Motherboard
Blitz Extreme
E3152
First Edition V1
June 2007
Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any
means, except documentation kept by the purchaser for backup purposes, without the express written
permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Contents
Notices........................................................................................................ viii
Safety information....................................................................................... ix
About this guide........................................................................................... x
Blitz Extreme specifications summary..................................................... xii
Chapter 1:
Product introduction
1.1
Welcome!....................................................................................... 1-1
1.3
Special features............................................................................. 1-2
1.2
Package contents.......................................................................... 1-1
1.3.1
ROG intelligent Performace & Overclocking features . ... 1-2
1.3.3
Product highlights............................................................ 1-7
1.3.2
Chapter 2:
2.1
2.2
Motherboard overview.................................................................. 2-5
2.2.1
Placement direction......................................................... 2-5
2.2.3
Motherboard layout.......................................................... 2-6
2.2.4
2.2.5
Audio card layout............................................................. 2-6
Layout contents................................................................ 2-7
2.3.1
Installing the CPU.......................................................... 2-10
2.3.3
Uninstalling the CPU heatsink and fan.......................... 2-14
Installing the CPU heatsink and fan............................... 2-12
System memory.......................................................................... 2-16
2.4.1
Overview........................................................................ 2-16
2.4.3
Installing a DIMM........................................................... 2-19
2.4.2
2.5
Screw holes..................................................................... 2-5
Central Processing Unit (CPU).................................................... 2-9
2.3.2
2.4
Hardware information
Before you proceed...................................................................... 2-1
2.2.2
2.3
ROG unique features ...................................................... 1-4
2.4.4
Memory configurations................................................... 2-17
Removing a DIMM......................................................... 2-19
Expansion slots........................................................................... 2-20
2.5.1
Installing an expansion card.......................................... 2-20
2.5.3
Interrupt assignments.................................................... 2-21
2.5.2
2.5.4
2.5.5
Configuring an expansion card...................................... 2-20
PCI slots......................................................................... 2-22
PCI Express x1 slots...................................................... 2-22
iii
Contents
2.6
2.7
2.8
2.5.6
EL I/O shield, LCD Poster and Audio card Installation............ 2-24
2.7.1
2.7.2
Rear panel connectors................................................... 2-26
2.8.3
Onboard switches.......................................................... 2-38
2.8.5
Chapter 3:
3.2.1
Powering up
Using the OS shut down function..................................... 3-2
Using the dual function power switch............................... 3-2
BIOS setup
4.1.1
ASUS Update utility......................................................... 4-1
4.1.3
ASUS EZ Flash 2 utility.................................................... 4-5
4.1.4
4.1.5
Creating a bootable floppy disk........................................ 4-4
AFUDOS utility................................................................. 4-6
ASUS CrashFree BIOS 3 utility....................................... 4-8
BIOS setup program..................................................................... 4-9
4.2.1
BIOS menu screen......................................................... 4-10
4.2.3
Navigation keys.............................................................. 4-10
4.2.2
4.2.4
4.2.5
4.2.6
4.2.7
4.2.8
iv
Installing the DIY Pedestal............................................. 2-41
Managing and updating your BIOS............................................. 4-1
4.1.2
4.3
Installing the optional fans............................................. 2-39
Turning off the computer.............................................................. 3-2
Chapter 4:
4.2
Internal connectors........................................................ 2-29
Starting up for the first time......................................................... 3-1
3.2.2
4.1
Audio card Installation.................................................... 2-25
2.8.1
2.8.4
3.2
EL I/O shield and LCD Poster Installation...................... 2-24
Connectors.................................................................................. 2-26
2.8.2
3.1
PCI Express x16 slots.................................................... 2-22
Jumper......................................................................................... 2-23
4.2.9
Menu bar........................................................................ 4-10
Menu items.....................................................................4-11
Sub-menu items..............................................................4-11
Configuration fields.........................................................4-11
Pop-up window...............................................................4-11
Scroll bar.........................................................................4-11
General help...................................................................4-11
Main menu................................................................................... 4-12
Contents
4.3.1
System Time [xx:xx:xx].................................................. 4-12
4.3.3
Legacy Diskette A [1.44M, 3.5 in.].................................. 4-12
4.3.2
4.3.4
Language [English]........................................................ 4-12
4.3.5
SATA 1-6...........................................................................................4-13
4.3.7
AHCI Configuration........................................................ 4-15
4.3.6
4.4
System Date [Day xx/xx/xxxx]........................................ 4-12
4.3.8
SATA Configuration........................................................ 4-14
System Information........................................................ 4-16
Extreme Tweaker menu.............................................................. 4-17
4.4.1
Ai Overclocking [Auto].................................................... 4-17
PCIE Frequency [Auto]................................................................. 4-18
DRAM Frequency [Auto]............................................................... 4-18
DRAM Timing Control [Auto]......................................................... 4-18
Loadline Calibration [Auto]............................................................ 4-20
FSB Termination Voltage [Auto].................................................... 4-20
DRAM Voltage [Auto].................................................................... 4-21
South Bridge Voltage [Auto].......................................................... 4-21
PLL Voltage [Auto]........................................................................ 4-21
NB LED Selection [NB Volt].......................................................... 4-22
4.5
SB LED Selection [PLL Volt]......................................................... 4-22
Advanced menu.......................................................................... 4-22
4.5.1
Ai Net 2.......................................................................... 4-23
4.5.3
CPU Configuration......................................................... 4-25
4.5.2
4.5.4
4.5.5
4.6
4.5.6
Chipset........................................................................... 4-26
OnBoard Devices Configuration.................................... 4-27
PCI PnP......................................................................... 4-28
Power menu................................................................................. 4-29
4.6.1
Suspend Mode [Auto].................................................... 4-29
4.6.3
ACPI 2.0 Support [Enabled]........................................... 4-29
4.6.2
4.6.4
4.6.5
4.7
USB Configuration......................................................... 4-23
4.6.6
Repost Video on S3 Resume [Disabled]........................ 4-29
ACPI APIC Support [Enabled]........................................ 4-29
APM Configuration......................................................... 4-30
Hardware Monitor.......................................................... 4-31
Boot menu................................................................................... 4-35
Contents
4.7.1
Boot Device Priority....................................................... 4-35
4.7.3
Security.......................................................................... 4-37
4.7.2
4.8
4.9
Tools menu.................................................................................. 4-39
4.8.1
4.8.2
5.2
5.2.1
Running the support DVD................................................ 5-1
5.2.3
Utilities menu................................................................... 5-3
5.2.5
5.2.6
5.2.7
Make disk menu............................................................... 5-5
Manual menu................................................................... 5-6
ASUS Contact information............................................... 5-6
Other information............................................................. 5-7
5.3.1
ASUS MyLogo3™............................................................ 5-9
5.3.3
ASUS PC Probe II.......................................................... 5-12
5.3.4 5.3.5 5.3.6
5.3.7
5.3.8
5.3.9
5.3.10
AI NET2..........................................................................5-11
ASUS AI Suite................................................................ 5-18
ASUS AI Gear 2............................................................. 5-20
ASUS AI Nap................................................................. 5-21
ASUS AI N.O.S.............................................................. 5-22
ASUS Q-Fan Plus.......................................................... 5-23
ASUS AI Booster............................................................ 5-24
SoundMAX® High Definition Audio utility........................ 5-25
RAID configurations................................................................... 5-30
5.4.1
RAID definitions............................................................. 5-30
5.4.2
Installing Serial ATA hard disks...................................... 5-31
5.4.4
JMicron® RAID Configuration......................................... 5-39
5.4.3
vi
Drivers menu.................................................................... 5-2
Software information.................................................................... 5-9
5.3.2
5.5
Software support
Support DVD information............................................................. 5-1
5.2.4
5.4
ASUS O.C. Profile.......................................................... 4-40
Installing an operating system.................................................... 5-1
5.2.2
5.3
ASUS EZ Flash 2........................................................... 4-39
Exit menu..................................................................................... 4-41
Chapter 5:
5.1
Boot Settings Configuration........................................... 4-36
Intel® RAID configurations.............................................. 5-31
Creating a RAID driver disk........................................................ 5-47
5.5.1
Creating a RAID driver disk without entering the OS..... 5-47
5.5.2
Chapter 6:
6.1
6.2
6.3
6.1.1
6.1.2
A.3
A.4
Requirements................................................................... 6-1
Before you begin.............................................................. 6-1
Installing CrossFire™ graphics cards........................................ 6-2
Software information.................................................................... 6-5
6.3.1
Appendix:
A.2
ATI® CrossFire™ technology support
Overview........................................................................................ 6-1
6.3.2
A.1
Creating a RAID driver disk in Windows®....................................... 5-47
Installing the device drivers.............................................. 6-5
Using the Catalyst™ Control Center................................ 6-7
CPU features
Intel® EM64T...................................................................................A-1
Enhanced Intel SpeedStep® Technology (EIST).........................A-1
A.2.1
A.2.2
System requirements.......................................................A-1
Using the EIST.................................................................A-2
Intel Hyper-Threading Technology............................................A-3
®
Debug Code Table.........................................................................A-4
vii
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
viii
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing system
before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure
that all power cables are unplugged.
• Seek professional assistance before using an adpater or extension cord.
These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using,
contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully read all
the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in
any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
ix
About this guide
This user guide contains the information you need when installing and configuring
the motherboard.
How this guide is organized
This guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports.
•
Chapter 2: Hardware information
•
Chapter 3: Powering up
•
Chapter 4: BIOS setup
•
Chapter 5: Software support
•
Chapter 6: ATI CrossFire™ support
•
Appendix: CPU features
This chapter lists the hardware setup procedures that you have to perform
when installing system components. It includes description of the switches,
jumpers, and connectors on the motherboard.
This chapter describes the power up sequence and ways of shutting down
the system.
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
This chapter describes the contents of the support CD that comes with the
motherboard package and the software.
This chapter describes the ATI CrossFire™ feature and shows the graphics
card installation procedures.
The Appendix describes the CPU features and technologies that the
motherboard supports as well as the debug code table for the LCD Poster.
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
2.
ASUS websites
The ASUS website provides updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
Optional documentation
Your product package may include optional documentation, such as warranty
flyers, that may have been added by your dealer. These documents are not
part of the standard package.
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Indicates a menu or an item to select.
Italics
Used to emphasize a word or a phrase.
<Key> Keys enclosed in the less-than and greater-than sign
means that you must press the enclosed key.
Example: <Enter> means that you must press the
Enter or Return key.
<Key1+Key2+Key3>
If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command exactly
as shown, then supply the required item or value
enclosed in brackets.
Example: At the DOS prompt, type the command line:
afudos /i[filename]
afudos /iBlitz-Extreme.ROM
xi
Blitz Extreme specifications summary
CPU
LGA775 socket for Intel® Core™2 Quad /
Core™2 Extreme / Core™2 Duo / Pentium® Extreme /
Pentium® D / Pentium® 4 / Celeron® D Processors
Support Intel® next generation 45nm Multi-Core CPU
Compatible with Intel® 06/05B/05A processors
* Refer to www.asus.com for Intel CPU support list
Chipset
Intel® P35 / ICH9R with Intel® Fast Memory Access
Technology
System Bus
1333 / 1066 / 800 MHz
Memory
4 x DIMM, max. 8GB, DDR3 1333* / 1066 / 800 MHz,
non-ECC, un-buffered memory
Dual channel memory architecture
* This chipset officially supports the memory frequency
up to DDR3 1066MHz. Tuned by ASUS Super
Memspeed Technology, this motherboard natively
supports up to DDR3 1333. Refer to www.asus.com or
user manual for Memory QVL (Qualified Vendor List).
Expansion Slots
2 x PCI Express x16 slots (support dual graphics
solution)
3 x PCI Express x1 (PCIEx1_1 is compatible with the
audio slot.)
2 x PCI 2.2
CrossFire™ Technology
Support ATI CrossFire™ graphics cards (both at x8
mode)
Storage
Southbridge
- 6 x SATA 3.0 Gb/s ports
- Intel Matrix Storage Technology supports RAID 0, 1,
10, 5.
JMicron® JMB363 PATA and SATA controller
- 1 x UltraDMA 133/100/66 for up to 2 PATA devices
- 2 x External SATA 3.0 Gb/s port (SATA On-the-Go)
LAN
Dual Gigabit LAN controllers, both featuring AI NET2
High Definition Audio
SupremeFX II Audio Card
- ADI 1988B 8-channel High Definition Audio CODEC
- Noise Filter
Coaxial / Optical S/PDIF out ports at back I/O
IEEE 1394
VIA 6308P 1394a controller supports 2 x 1394a ports
(one at midboard; one at back I/O)
USB
12 x USB 2.0 ports (6 ports at mid-board, 6 ports at back
panel)
(continued on the next page)
xii
Blitz Extreme specifications summary
ASUS Exclusive
Overclocking features
Crosslinx technology
Extreme Tweaker
Loadline Calibration
Intelligent overclocking tools:
- CPU level up
- AI NOS™ (Non-delay Overclocking System)
- AI Overclocking (intelligent CPU frequency tuner)
- AI Booster Utility
- O.C. Profile
Overclocking protection:
- COP EX (Component Overheat Protection -EX)
- Voltiminder LED
- ASUS C.P.R. (CPU Parameter Recall)
ASUS Special Features
Fusion Block System
LCD Poster
EL I/O
Onboard Switches: Power / Reset / Clr CMOS
Q-Connector
Q-Fan Plus
ASUS EZ Flash2
ASUS CrashFree BIOS3
ASUS MyLogo3™
Multi-Language BIOS
Back Panel I/O Ports
1 x PS/2 Keyboard (purple)
1 x S/PDIF Out (Coaxial + Optical)
2 x External SATA
2 x LAN (RJ45) port
6 x USB 2.0/1.1 ports
1 x IEEE1394a port
1 x Clr CMOS switch
Internal I/O Connectors
3 x USB 2.0 connectors support additional 6 USB 2.0
ports
1 x Floppy disk drive connector
1 x IDE connector for two devices
6 x SATA connectors
8 x Fan connectors (1 x CPU/ 1 x Power/ 4 x Chassis/
2 x Optional)
2 x Thermal sensor connectors
1 x IEEE1394a connector
1 x S/PDIF Out connector
1 x Chassis Intrusion connector
24-pin ATX Power connector
8-pin ATX 12V Power connector
1 x En/Dis-able Clr CMOS
1 x EL I/O Shield connector
1 x System panel connector
1 x LCD poster connector
(continued on the next page)
xiii
Blitz Extreme specifications summary
BIOS Features
16 Mb AMI BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.4,
ACPI 2.0a Multi-Language BIOS
Manageability
WOL by PME, Chassis Intrusion, PXE
Accessories
Fusion Block System Accessory
ASUS Optional Fan
DIY Pedestal
3 in 1 ASUS Q-connector kit
UltraDMA 133/100/66 cable
Floppy disk drive cable
Serial ATA cables
Serial ATA power cables
2-port USB2.0 module
IEEE1394a module
EL I/O Shield
Thermal sensor cables
Cable ties
User's manual
Software
The hottest 3D game: S.T.A.L.K.E.R
Support DVD:
Drivers
ASUS PC Probe II
ASUS Update
ASUS AI Suite
Futuremark® 3DMark® 06 Advanced Edition
Kaspersky Anti-Virus software
Form Factor
ATX Form Factor, 12”x 9.6” (30.5cm x 24.5cm)
*Specifications are subject to change without notice.
xiv
This chapter describes the motherboard
features and the new technologies
it supports.
1
Product
introduction
Chapter summary
1
1.1
Welcome!....................................................................................... 1-1
1.3
Special features............................................................................. 1-2
1.2
Package contents.......................................................................... 1-1
ASUS Blitz Extreme
1.1
Welcome!
Thank you for buying an ASUS® Blitz Extreme motherboard!
The motherboard delivers a host of new features and latest technologies, making it
another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS Blitz Extreme
I/O modules
USB 2.0 module
IEEE 1394a module
Cables
Ultra DMA 133/100/66 cable
Floppy disk drive cable
Serial ATA cables
Serial ATA power cables
Thermal sensor cables
Accessories
Fusion Block System Accessory
EL I /O shield
LCD Poster
ASUS Optional Fan
3-in-1 ASUS Q-Connector Kit
Cable ties
DIY Pedestal
DVD/CD
ASUS motherboard support DVD
The hottest game: S.T.A.L.K.E.R
Documentation
User guide
If any of the above items is damaged or missing, contact your retailer.
ASUS Blitz Extreme
1-
1.3
Special features
1.3.1
ROG intelligent Performace & Overclocking features
Crosslinx
Crosslinx is a unique technology utilizing a dedicated special graphics controller
to optimize PCIe allocation with dual x8 lanes. Such architecture eliminates the x4
bottleneck found on competing x16, x4 solutions. Hence, the Crosslinx is able to
provide faster graphics performance.
Fusion Block System
Building on the ROG unique heatpipe, the Fusion Block System (FBS) provides
dual paths to cool down the motherboard. Users will be able to connect the FBS
with the watercooling circuit.
Component Overheat Protection -EX (COP EX)
When the temperature of Northbridge and Southbridge reaches the limit of
specifications, the motherboard will automatically shut down to protect NB and SB
from burning.
Voltiminder LED
The voltage warning LED uses green, yellow, and red light on the motherboard to
highlight the voltage status of each respecitve component (CPU, memory, NB, SB).
2-Phase DDR3
The 2-phase DDR3 supplies stable power to memory in turns. Each phase only
shoulders half of the loading compared with the only one phase power module.
8 phase DrMOS power
The DrMOS, the next generation of CPU power module, provides higher efficiency
for energy saving and higher quality power supply to the processor. With thtis
latest technology, this motherboard allows users to reach the highest overclock
frequency and to have the most stable platform.
Super Memspeed Technology
To attain top performance, ASUS has managed to break through current FSB
and DRAM ratio proportions by utilizing Super Memspeed Technology- the latest
technology that provides even more precise overclocking options to unleash
the true potential of DDR3 memory. Native DDR3 1333 maximizes system
performance by eliminating the bottleneck when overclocking both the CPU and
the memory- providing great performance for 3D graphics and other memory
demanding applications.
1-
Chapter 1: Product Introduction
Loadline Calibration
The Loadline calibration ensures stable and optimal CPU voltage when heavy
loading.
Extreme Tweaker
This feature allows you to fine tune the CPU/memory voltage and gradually
increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz
increment to achieve maximum system performance.
AI NOS™ (Non-Delay Overclocking System)
The patented ASUS Non-delay Overclocking System™ (AI NOS™) technology
auto‑detects the CPU loading and dynamically overclocks the CPU speed when
needed. Unlike other dynamic overclocking techniques, AI NOS™ reacts much
faster to satisfy your need for speed. See page 4-17 and 5-22 for details.
AI Booster
The ASUS AI Booster allows you to overclock the CPU speed in Windows
environment without the hassle of booting the BIOS.
ASUS O.C. Profile
The motherboard features the ASUS O.C. Profile that allows users to conveniently
store or load multiple BIOS settings. The BIOS settings can be stored in the
CMOS or a separate file, giving users freedom to share and distribute their favorite
settings. See page 4-40 for details.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the
BIOS default settings in case the system hangs due to overclocking. When the
system hangs due to overclocking, C.P.R. eliminates the need to open the system
chassis and clear the RTC data. Simply shut down and reboot the system, and the
BIOS automatically restores the CPU default setting for each parameter.
ASUS Blitz Extreme
1-
1.3.2
ROG unique features
Supreme FX II features
Supreme FX II extends all the features of the 1st generation and places a shielding
to enhancethe sound quality. It also lights up the model name with stylish LEDs.
Noise Filter
This feature detects repetitive and stationary noises (non-voice signals) like
computer fans, air conditioners, and other background noises then eliminates
it in the incoming audio stream while recording. See page 5-29 for details.
LCD Poster
The LCD Poster uses an external panel to smartly display the error message of the
physical system during the Power-On Self Test (POST) to inform you the boot error
instead of the “code name.”
Onboard Switches
A power-on button, a reset button, and a clear CMOS button are onboard to
provide overclockers and gamers the convenience of fine-tuning performance
when working on a bare (open-case) system. Press the power-on button to wake
up the system, the reset button to reboot, and the clear CMOS button to clear
setup information when the system hangs due to overclocking. See page 2-38 for
details.
ASUS Q-Fan plus technology
The ASUS Q-Fan plus technology smartly adjusts the CPU and chassis fan
1 speeds according to the system loading to ensure quiet, cool, and efficient
operation. See pages 4-32 and 5-23 for details.
Optional Fan (for water-cooling/passive-cooling only)
The optional fan is specifically designed to provide sufficient airflow over the CPU
power modules and chipset area when water-cooling or passive-cooling is utilized,
ensuring effective heat dissipation for the entire system. See page 2-39 for details.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice from the
available options. The localized BIOS menus allow easier and faster configuration.
See page 4-12 for details.
1-
Chapter 1: Product Introduction
ASUS MyLogo3
This new feature present in the motherboard allows you to personalize and add
style to your system with customizable boot logos. See page 5-9 for details.
ASUS Quiet Thermal Solution
ASUS Quiet Thermal solution makes system more stable and enhances the
overclocking capability.
AI Gear 2
AI Gear 2 allows you to choose from profiles to adjust CPU frequency and
vCore voltage, minimizing system noise and saving 50% power consumption
at most. You can real-time chnage the mode under operating system to suit
your needs. See page 5-20 for details.
AI Nap
With AI Nap, the system can continue running at minimum power and noise
when you are temporarily away. To wake the system and return to the OS
environment, simply click the mouse or press a key. See page 5-21 for
details.
8-Phase Power Design
The ASUS 8-Phase Power Design provides highly efficient operation to
generate less heat (at least 15°C (59°F)) than other conventional power
solutions. It reduces input ripple current and output ripple voltage, which
keeps CPU and power module from suffering the risk of high power stress.
It has the advantages of quick transient response and stability, especially
beneficial when CPU requires more current immediately under heavy loading
or overclocking mode.
Fanless Design - Stack Cool 2
ASUS Stack Cool 2 is a fan-less and zero-noise cooling solution that lowers
the temperature of critical heat generating components. The motherboard
uses a special design on the printed circuit board (PCB) to dissipate heat
these critical components generate.
ASUS EZ DIY
ASUS EZ DIY feature collection provides you easy ways to install computer
components, update the BIOS or back up your favorite settings.
ASUS Blitz Extreme
1-
ASUS Q-Connector
ASUS Q-Connector allows you to easily connect or disconnect the chassis
front panel cables to the motherboard. This unique module eliminates the
trouble of connecting the system panel cables one at a time and avoiding
wrong cable connections. See page 2-37 for details.
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data
from a USB flash disk containing the BIOS file. See page 4-8 for details.
ASUS EZ Flash 2
EZ Flash 2 is a user-friendly BIOS update utility. Simply press the predefined
hotkey to launch the utility and update the BIOS without entering the OS.
Update your BIOS easily without preparing a bootable diskette or using an
OS-based flash utility. See pages 4-5 and 4-39 for details.
1-
Chapter 1: Product Introduction
1.3.3
Product highlights
Green ASUS
This motherboard and its packaging comply with the European Union’s Restriction
on the use of Hazardous Substances (RoHS). This is in line with the ASUS vision
of creating environment-friendly and recyclable products/packaging to safeguard
consumers’ health while minimizing the impact on the environment.
Intel® Quad-core Processor Ready
This motherboard supports the latest Intel® Quad-core processors in the LGA775
package. It is excellent for multi-tasking, multi-media and enthusiastic gamers.
Intel® Quad-core processor is one of the most powerful CPU in the world.
Intel® Core™2 Duo/ Intel® Core™2 Extreme CPU support
This motherboard supports the latest Intel® Core™2 processor in the LGA775
package. With the new Intel® Core™ microarchitecture technology and 1333/ 1066
/ 800 MHz FSB, the Intel® Core™2 is one of the most powerful and energy efficient
CPUs in the world.
Intel P35 Chipset
The Intel® P35 Express Chipset is the latest chipset designed to support 8GB
of dual-channel DDR3 1066/800 architecture, 1333/1066/800 FSB (Front Side
Bus), PCI Express x16 graphics and multi-core CPU. It especially includes Intel®
Fast Memory Access technology that significantly optimizes the use of available
memory bandwidth and reduces the latency of the memory accesses.
DDR3 memory support
The motherboard supports DDR3 memory that features data transfer rates of 1066
/ 800 MHz to meet the higher bandwidth requirements of the latest 3D graphics,
multimedia, and Internet applications. The dual-channel DDR3 architecture
doubles the bandwidth of your system memory to boost system performance.
Furthermore, this motherboard does not restrict the memory size across two
channels. Users may install different memory size DIMMs into the two channels
and enjoy dual-channel and single-channel functions at the same time. This new
feature optimizes the use of available memory size.
ASUS Blitz Extreme
1-
Serial ATA 3.0 Gb/s technology and SATA-On-The-Go
This motherboard supports the next-generation hard drives based on the Serial ATA
(SATA) 3Gb/s storage specification, delivering enhanced scalability and doubling
the bus bandwidth for high-speed data retrieval and saves. The external SATA port
located at the back I/O provides smart setup and hot-plug functions. Easily backup
photos, videos and other entertainment contents to external devices. See page
2-27 for details.
Dual RAID solution
The Intel® P35 chipset incorporates six Serial ATA connectors with high
performance RAID 0, 1, 5 and 10 functions. Making this motherboard an ideal
solution to enhance hard disk performance and data back up protection without the
cost of add-on cards. See page 2-30 for details.
IEEE 1394a support
The IEEE 1394a interface provides high speed digital interface for audio/video
appliances such as digital television, digital video camcorders, storage peripherals
& other PC portable devices. See pages 2-28 and 2-32 for details.
S/PDIF digital sound ready
This motherboard provides convenient connectivity to external home theater audio
systems via coaxial and optical S/PDIF-out (SONY-PHILIPS Digital Interface) jacks.
It allows to transfer digital audio without converting to analog format and keeps the
best signal quality. See pages 2-28 and 2-35 for details.
Dual Gigabit LAN solution
The integrated dual Gigabit LAN design allows a PC to serve as a network gateway
for managing traffic between two separate networks. This capability ensures rapid
transfer of data from WAN to LAN without any added arbitration or latency. See
page 2-26 for details.
High Definition Audio
Enjoy high-end sound quality on your PC! The onboard 8-channel HD audio (High
Definition Audio, previously codenamed Azalia) CODEC enables high-quality
192KHz/24-bit audio output, jack-sensing feature, retasking functions and multistreaming technology that simultaneously sends different audio streams to different
destinations. You can now talk to your partners on the headphone while playing
multi-channel network games. See pages 2-27 for details.
1-
Chapter 1: Product Introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components. It
includes description of the jumpers and
connectors on the motherboard.
2
Hardware
information
Chapter summary
2
2.1
Before you proceed...................................................................... 2-1
2.3
Central Processing Unit (CPU).................................................... 2-9
2.2
2.4
2.5
Motherboard overview.................................................................. 2-5
System memory.......................................................................... 2-16
Expansion slots........................................................................... 2-20
2.6
Jumper......................................................................................... 2-23
2.8
Connectors.................................................................................. 2-26
2.7
EL I/O, LCD Poster and Audio card Installation....................... 2-24
ASUS Blitz Extreme
2.1
Before you proceed
Take note of the following precautions before you install motherboard components
or change any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
Before you install or remove any component, ensure
that the ATX power supply is switched off or the power cord is detached
from the power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.
Onboard LEDs
The motherboard comes with LEDs that indicate the voltage conditions of CPU,
memory, northbridge, southbridge and FSB frenquency. You may adjust the
voltages in BIOS. There are also an LED for hard disk drive activity and an onboard
switch for power status. For more information on voltage adjustment, refer to 4.4
Extreme Tweaker menu
CPU LED
Refer to the illustration below for the location of the CPU LED and the table
below for LED definition.
®
1.
CPU_CRAZY
CPU_HIGH
CPU_NORMAL
BLITZ EXTREME
BLITZ EXTREME CPU LED
CPU Voltage
ASUS Blitz Extreme
Normal (green)
High (yellow)
Crazy (red)
1.10000~1.50000
1.51250~1.69375
1.70000~1.90000
2-
2.
Refer to the illustration below for the location of the memory LED and the
table below for LED definition.
®
Memory LED
DDR_CRAZY
DDR_HIGH
DDR_NORMAL
BLITZ EXTREME
BLITZ EXTREME DDR LED
DRAM Voltage
High (yellow)
Crazy (red)
1.80~2.20
2.22~2.60
2.62~3.40
Northbridge/Southbridge LEDs
Northbridge and southbridge LEDs each have two different voltage displays.
The northbridge LED displays either the 1.25V NB voltage or the 1.20V
FSB termination voltage. The southbridge LED shows either the 1.50V CPU
PLL voltage or the 1.05V SB voltage. You can select the voltage to display
in BIOS. Refer to the illustration below for the location of the northbridge/
southbridge LEDs and the table below for LED definition.
®
3.
Normal (green)
NB_CRAZY
NB_HIGH
NB_NORMAL
SB_CRAZY
SB_HIGH
SB_NORMAL
BLITZ EXTREME
BLITZ EXTREME North/South Bridge LED
North Bridge Voltage
Normal (green)
High (yellow)
Crazy (red)
1.25~1.59
1.61~1.83
1.85~2.03
1.42~1.60
1.62~1.80
1.50~1.60
1.62~1.80
1.82~2.00
1.050~1.125
1.150~1.175
1.200~1.225
FSB Termination Voltage 1.20~1.40
PLL Voltage
South Bridge Voltage
2-
Chapter 2: Hardware information
FSB frenquency LED
There are five LEDs that light up to indicate the level of FSB frequency. One
lit blue LED suggests that the frequency is low (default), while five lit blue
LEDs shows that the frequency is high (fast). Refer to the illustration below
for the location of the FSB frenquency LEDs and the table below for LED
definition.
®
4.
BLITZ EXTREME
Fast
Default
BLITZ EXTREME Frequency LED
200-299
300-399
400-499
500-599
600~
CPU FSB (Default) (Overclocking) (Overclocking) (Overclocking) (Overclocking)
200MHz
1
2
3
4
5
(Default)
(Fast)
266-299
300-399
400-499
500-599
600~
CPU FSB (Default) (Overclocking) (Overclocking) (Overclocking) (Overclocking)
266MHz
1
2
3
4
5
(Default)
(Fast)
333-399
400-499
500-549
550-599
600~
CPU FSB (Default) (Overclocking) (Overclocking) (Overclocking) (Overclocking)
333MHz
1
2
3
4
5
(Default)
(Fast)
ASUS Blitz Extreme
2-
Hard Disk LED
The HD LED is designed for indication of the hard disk activity. It blinks when
the data is written into or read from the hard disk drive. It stays unlit if there is
no hard disk connected to the motherboard or the hard disk does not function.
®
5.
HD_LED
BLITZ EXTREME
BLITZ EXTREME Hard Disk LED
Power LED
The motherboard comes with a power-on switch as the standby power LED.
The swtich lights up to indicate that the system is ON, in sleep mode, or in
soft‑off mode. This is a reminder that you should shut down the system and
unplug the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard poweron switch.
®
6.
BLITZ EXTREME
BLITZ EXTREME Power on switch
2-
Chapter 2: Hardware information
2.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to
ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components.
2.2.1
Placement direction
When installing the motherboard, make sure that you place it into the chassis in the
correct orientation. The edge with external ports goes to the rear part of the chassis
as indicated in the image below.
2.2.2
Screw holes
Place nine (9) screws into the holes indicated by circles to secure the motherboard
to the chassis.
®
DO NOT overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
BLITZ EXTREME
ASUS Blitz Extreme
2-
2.2.3
Motherboard layout
24.5cm (9.6in)
EATX12V
LCD_CON
CPU_FAN
SPDIF_O12
EATXPWR
LGA775
CHA_FAN4
LAN1_USB12
CHA_FAN1
PCIEX1_1
NB_CRAZY
NB_HIGH
NB_NORMAL
ADH
JMB363
CR2032 3V
Lithium Cell
CMOS Power
PCI1
Marvell
88E8001
VIA
VT6308P
FLOPPY
CHA_FAN3
30.5cm (12.0in)
88E8056
DDR2 DIMM_B2 (64 bit,240-pin module)
Intel®
P35
LAN2_USB34
DDR2 DIMM_B1 (64 bit,240-pin module)
CPU_CRAZY
CPU_HIGH
CPU_NORMAL
DDR2 DIMM_A2 (64 bit,240-pin module)
ESATA12
E1394
DDR2 DIMM_A1 (64 bit,240-pin module)
®
SPDIF_OUT
CLR_CMOS
PRI_EIDE
KB_USB56
PWR_FAN
DDR_CRAZY
DDR_HIGH
DDR_NORMAL
PCIEX16_1
PCIEX1_2
PCIEX1_3
CLRTC_SW
IDT
PES24N3A
BLITZ EXTREME
PCI2
OPT_FAN1
OPT_TEMP2
BIOS
RST_SW
PWR_SW
SATA34
SATA56
OPT_FAN2
CHASSIS
IE1394_2
OPT_TEMP1
SATA12
SB_CRAZY
SB_HIGH
SB_NORMAL
PCIEX16_2
Super
I/O
HD_LED
Intel®
ICH9R
USB1112
USB910
FREQUENCY
Fast
CHA_FAN2
USB78
Default
PANEL
Refer to 2.8 Connectors for more information about rear panel connectors and
internal connectors.
2.2.4
Audio card layout
SUPREMEFX II
Listen with Absolute HD
2-
Chapter 2: Hardware information
2.2.5
Slots
1.
Layout contents
DDR3 DIMM slots
2.
PCI slots
4.
PCI Express x16 slots
3.
Jumper
1.
PCI Express x 1 slots
Clear RTC RAM (3-pin CLRTC)
Page
2-16
2-22
2-22
2-22
Page
2-23
Rear panel connectors
Page
2.
Coaxial S/PDIF Out port
2-26
4.
LAN 1 (RJ-45) port
1.
3.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
PS/2 keyboard port (purple)
LAN 2 (RJ-45) port
Line In port (light blue)
Line Out port (lime)
Microphone port (pink)
Center/Subwoofer port (orange)
Rear Speaker Out port (black)
Side Speaker Out port (gray)
USB 2.0 ports 1, 2, 3 and 4
External SATA port 1/2
IEEE 1394a port
Clear CMOS switch
Optical S/PDIF Out port
USB 2.0 ports 5 and 6
ASUS Blitz Extreme
2-26
2-26
2-26
2-27
2-27
2-27
2-27
2-27
2-27
2-27
2-27
2-28
2-28
2-28
2-28
2-
Internal connectors
Page
2.
IDE connector (40-1 pin PRI_EIDE)
2-29
4.
USB connectors (10-1 pin USB78, USB910, USB1112)
1.
3.
5.
6.
ICH9R Serial ATA connectors (7-pin SATA1-6)
IEEE 1394a port connector (10-1 pin IE1394_2)
Thermal sensor cable connectors (2-pin OPT_TEMP1-2)
2-29
2-30
2-31
2-32
2-32
7.
CPU, chassis, and optional fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN1-4, 3-pin PWR_FAN,
3‑pin OPT_FAN1-2)
2-33
9.
ATX power connectors (24-pin EATXPWR, 2x4-pin EATX12V)
2-34
8.
10.
11.
Chassis intrusion connector (4-1 pin CHASSIS)
2-34
Digital audio connector
(4-1 pin SPDIF, for ASUS HDMI VGA card)
2-35
System panel connector (20-8 pin PANEL)
2-36
Onboard switches
Page
2.
2-38
1.
2-
Floppy disk drive connector (34-1 pin FLOPPY)
Power-on switch
Reset switch
2-38
Chapter 2: Hardware information
2.3
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for the
Intel® Core™2 Quad/ Core™2 Extreme/ Core™2 DUO/ Core™2/ Pentium® D/
Pentium® 4/ Pentium® Extreme.
•
Make sure that all power cables are unplugged before installing the CPU.
•
If installing a dual-core CPU, connect the chassis fan cable to the
CHA_FAN1 connector to ensure system stability.
•
Upon purchase of the motherboard, make sure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS will shoulder the cost
of repair only if the damage is shipment/transit-related.
•
•
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the LGA775 socket.
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
ASUS Blitz Extreme
2-
2.3.1
Installing the CPU
To install a CPU:
Locate the CPU socket on the motherboard.
®
1.
BLITZ EXTREME
BLITZ EXTREME CPU Socket 775
Before installing the CPU, make sure that the cam box is facing towards you
and the load lever is on your left.
2.
Press the load lever with your thumb (A), then move it to the left (B) until it is
released from the retention tab.
Retention tab
Load lever
A
PnP cap
B
This side of the socket box
should face you.
To prevent damage to the socket pins, do not remove the PnP cap unless you
are installing a CPU.
3.
2-10
Lift the load lever in the direction of
the arrow to a 135º angle.
Chapter 2: Hardware information
4.
Lift the load plate with your thumb
and forefinger to a 100º angle (A),
then push the PnP cap from the load
plate window to remove (B).
B
A
Load plate
Alignment key
5.
Position the CPU over the
socket, making sure that
the gold triangle is on the
bottom‑left corner of the
socket then fit the socket
alignment key into the
CPU notch.
CPU notch
Gold triangle mark
The CPU fits in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
6.
7.
A
Close the load plate (A), then
push the load lever (B) until it
snaps into the retention tab.
If installing a dual-core CPU,
connect the chassis fan cable
to the CHA_FAN1 connector to
ensure system stability.
B
The motherboard supports Intel® LGA775 processors with the Intel® Enhanced
Memory 64 Technology (EM64T), Enhanced Intel SpeedStep® Technology
(EIST), and Hyper-Threading Technology. Refer to the Appendix for more
information on these CPU features.
ASUS Blitz Extreme
2-11
2.3.2
Installing the CPU heatsink and fan
The Intel LGA775 processor requires a specially designed heatsink and fan
assembly to ensure optimum thermal condition and performance.
®
•
When you buy a boxed Intel® processor, the package includes the CPU fan
and heatsink assembly. If you buy a CPU separately, make sure that you
use only Intel®‑certified multi‑directional heatsink and fan.
•
Your Intel® LGA775 heatsink and fan assembly comes in a push-pin design
and requires no tool to install.
•
If you purchased a separate CPU heatsink and fan assembly, make sure
that you have properly applied Thermal Interface Material to the CPU
heatsink or CPU before you install the heatsink and fan assembly.
Make sure that you have installed the motherboard to the chassis before you
install the CPU fan and heatsink assembly.
To install the CPU heatsink and fan:
1.
Place the heatsink on top of the
installed CPU, making sure that the
four fasteners match the holes on
the motherboard.
Orient the heatsink and fan
assembly such that the CPU fan
cable is closest to the CPU fan
connector.
Motherboard hole
Fastener
Narrow end
of the groove
Make sure to orient each fastener with the narrow end of the groove pointing
outward. (The photo shows the groove shaded for emphasis.)
2-12
Chapter 2: Hardware information
2.
Push down two fasteners at a time in
a diagonal sequence to secure the
heatsink and fan assembly in place.
B
A
A
3.
A
B
B
A
B
Connect the CPU fan cable to the connector on the motherboard labeled
CPU_FAN.
®
CPU_FAN
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
BLITZ EXTREME
BLITZ EXTREME CPU fan connector
DO NOT forget to connect the CPU fan connector! Hardware monitoring errors
will occur if you fail to plug this connector.
ASUS Blitz Extreme
2-13
2.3.3
Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1. Disconnect the CPU fan cable from
the connector on the motherboard.
2.
Rotate each fastener
counterclockwise.
3.
Pull up two fasteners at a time in
a diagonal sequence to disengage
the heatsink and fan assembly from
the motherboard.
4.
2-14
A
B
B
A
B
A
A
B
Carefully remove the heatsink
and fan assembly from the
motherboard.
Chapter 2: Hardware information
5.
Rotate each fastener clockwise to
ensure correct orientation when
reinstalling.
Narrow end of the groove
The narrow end of the
groove should point outward
after resetting. (The photo
shows the groove shaded for
emphasis.)
Refer to the documentation in the boxed or stand-alone CPU fan package for
detailed information on CPU fan installation.
ASUS Blitz Extreme
2-15
2.4
System memory
2.4.1
Overview
The motherboard comes with four Double Data Rate 3 (DDR3) Dual Inline Memory
Modules (DIMM) sockets.
A DDR3 module has the same physical dimensions as a DDR3 DIMM but is
notched differently. DDR3 modules are developed for better performance with less
power consumption.
DIMM_B1
DIMM_B2
®
DIMM_A1
DIMM_A2
The figure illustrates the location of the DDR3 DIMM sockets:
BLITZ EXTREME
BLITZ EXTREME
240-pin DDR3 DIMM sockets
Channel
Channel A
Channel B
Sockets
DIMM_A1 and DIMM_A2
DIMM_B1 and DIMM_B2
This chipset officially supports DDR3 1066/800. With the ASUS Super
Memspeed Technology, the motherboard supports upto 1333MHz and provides
more ratio setting items. Refer to the table below for details.
1600
FSB
DDR3 1600 1333 1200 1000
2-16
800
1333
1333 1111 1000
833
1066
889
Chapter 2: Hardware information
2.4.2
Memory configurations
You may install 512 MB, 1 GB, and 2 GB unbuffered non‑ECC DDR3 DIMMs into
the DIMM sockets.
•
You may install varying memory sizes in Channel A and Channel B. The
system maps the total size of the lower-sized channel for the dual-channel
configuration. Any excess memory from the higher-sized channel is then
mapped for single-channel operation.
•
Always install DIMMs with the same CAS latency. For optimum
compatibility, it is recommended that you obtain memory modules from the
same vendor.
•
Due to chipset resource allocation, the system may detect less than 8 GB
system memory when you installed four 2 GB DDR3 memory modules.
•
If you install four 1 GB memory modules, the system may detect less than
3 GB of total memory because of address space allocation for other critical
functions. This limitation applies to Windows Vista 32-bit/Windows XP 32-bit
version operating system since it does not support PAE (Physical Address
Extention) mode.
•
If you install Windows Vista 32-bit/Windows XP 32-bit version operating
system, we recommend that you install less than 3GB of total memory.
Notes on memory limitations
•
Due to chipset limitation, this motherboard can only support up to
8 GB on the operating systems listed below. You may install a maximum of
2 GB DIMMs on each slot.
64-bit
Windows XP Professional x64 Edition
Windows Vista x64 Edition
ASUS Blitz Extreme
2-17
Blitz Extreme Motherboard Qualified Vendors Lists (QVL)
DDR3-1333MHz capability
Size
Vendor
Chip No.
CL Chip Brand
512MB
1024MB
512MB
1024MB
ELPIDA
ELPIDA
ELPIDA
ELPIDA
J5308BASE-DG-E
J5308BASE-DG-E
J5308BASE-DJ-E
J5308BASE-DJ-E
8
8
9
9
ELPIDA
ELPIDA
ELPIDA
ELPIDA
SS/
DS
SS
DS
SS
DS
Part No.
EBJ51UD8BAFA-DG-E
EBJ11UD8BAFA-DG-E
EBJ51UD8BAFA-DJ-E
EBJ11UD8BAFA-DJ-E
DIMM support
A*
B* C*
•
•
•
•
•
•
•
•
Blitz Extreme Motherboard Qualified Vendors Lists (QVL)
DDR3-1067 MHz capability
Size
Vendor
Chip No.
CL
Chip Brand
512MB
1024MB
512MB
1024MB
512MB
1024MB
1024MB
512MB
512MB
1024MB
Qimonda
Qimonda
ELPIDA
ELPIDA
NANYA
MICRON
SAMSUNG
SAMSUNG
Kingston
Kingston
IDSH51-03A1F1C-10F
IDSH51-03A1F1C-10F
J5308BASE-AC-E
J5308BASE-AC-E
NT5CB64M8AN-BE
D9GTR
K4B1G0846C-ZCF8
K4B510846E-ZCG8
IDSH51-03A1F1C-10F
J5308BASE-AC-E
N/A
N/A
8
8
N/A
7
8
8
N/A
N/A
QIMONDA
QIMONDA
ELPIDA
ELPIDA
NANYA
MICRON
SAMSUNG
SAMSUNG
QIMONDA
ELPIDA
SS/ Part No.
DS
DIMM support
A* B* C*
SS IMSH51U03A1F1C-10F
•
•
•
DS IMSH1GU13A1F1C-10F
•
•
SS EBJ51UD8BAFA-AG-E
•
•
•
DS EBJ11UD8BAFA-AG-E
•
•
SS NT512C64B88A0NY-BF
•
•
SS MT8JTF12864AY-1G1BZES •
•
•
SS M378B2873CZ0-CF8
•
•
•
SS M378B6573EZ0-CG8
•
•
SS KVR1066D3N7/512
•
•
•
DS KVR1066D3N7/1G
•
•
•
Blitz Extreme Motherboard Qualified Vendors Lists (QVL)
DDR3-800 MHz capability
Size
Vendor
Chip No.
CL
Chip Brand
512MB
512MB
1024MB
512MB
1024MB
1024MB
1024MB
2048MB
SAMSUNG
ELPIDA
ELPIDA
NANYA
NANYA
Qimonda
Hynix
Hynix
K4B510846E-ZCE7
J5308BASE-AC-E
J5308BASE-AC-E
NT5CB64M8AN-25D
NT5CB64M8AN-25D
IDSH51-03A1F1C-08E
HY5TQ1G831ZNF-S6
HY5TQ1G831ZNF-S5
N/A
6
6
N/A
N/A
N/A
N/A
N/A
SAMSUNG
ELPIDA
ELPIDA
NANYA
NANYA
QIMONDA
Hynix
Hynix
SS/
DS
SS
SS
DS
SS
DS
DS
SS
DS
Part No.
M378B6573EZ0-CE7
EBJ51UD8BAFA-8C-E
EBJ11UD8BAFA-8C-E
NT512C64B88A0NY-25D
NT1GC64B8HA0NY-25D
IMSH1GU13A1F1C-08E
HYMT112U64ZNF8-S6
HYMT125U64ZNF8-S5
DIMM support
A*
B*
C*
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
SS - Single-sided DS - Double-sided
DIMM support:
A - Supports one module inserted into either slot, in Single-channel memory configuration.
B - Supports one pair of modules inserted into either Channel A or Channel B as one pair of Dualchannel memory configuration.
C - Supports four modules inserted into the blue and white slots as two pairs of Dual‑channel
memory configuration.
Visit the ASUS website for the latest DDR3-1333/1067/800 MHz QVL.
2-18
Chapter 2: Hardware information
2.4.3
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both the
motherboard and the components.
2
To install a DIMM:
1.
2.
3.
3
Unlock a DIMM socket by pressing
the retaining clips outward.
Align a DIMM on the socket
such that the notch on the DIMM
matches the break on the socket.
DDR3 DIMM notch
1
1
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
Unlocked retaining clip
2.4.4
•
A DDR3 DIMM is keyed with a notch so that it fits in only one direction. DO
NOT force a DIMM into a socket to avoid damaging the DIMM.
•
The DDR3 DIMM sockets do not support DDR and DDR2 DIMMs. DO NOT
install DDR or DDR2 DIMMs to the DDR3 DIMM sockets.
Removing a DIMM
To remove a DIMM:
1.
Support the DIMM lightly with
your fingers when pressing the
retaining clips. The DIMM might
get damaged when it flips out
with extra force.
2.
2
Simultaneously press the retaining
clips outward to unlock the DIMM.
DDR3 DIMM notch
1
1
Remove the DIMM from the socket.
ASUS Blitz Extreme
2-19
2.5
Expansion slots
In the future, you may need to install expansion cards. The following sub‑sections
describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing expansion
cards. Failure to do so may cause you physical injury and damage motherboard
components.
2.5.1
Installing an expansion card
To install an expansion card:
1.
2.
3.
4.
5.
6.
Before installing the expansion card, read the documentation that came with
it and make the necessary hardware settings for the card.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
Remove the bracket opposite the slot that you intend to use. Keep the screw
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Secure the card to the chassis with the screw you removed earlier.
Replace the system cover.
2.5.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
2.
3.
Turn on the system and change the necessary BIOS settings, if any. See
Chapter 4 for information on BIOS setup.
Assign an IRQ to the card. Refer to the tables on the next page.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will
arise between the two PCI groups, making the system unstable and the card
inoperable. Refer to the table on the next page for details.
2-20
Chapter 2: Hardware information
2.5.3
Interrupt assignments
Standard interrupt assignments
IRQ
0
1
2­
3
4
5
6
7
8
9
10
11
12
13
14
15
Priority
Standard Function
1
2
—
11
12
13
14
15
3
4
5
6
7
8
9
10
System Timer
Keyboard Controller
Re-direct to IRQ#9
IRQ holder for PCI steering*
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
Printer Port (LPT1)*
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for PCI devices.
IRQ assignments for this motherboard
PCI slot 1
PCI slot 2
LAN(8001)
SATA(363)
LAN(8056)­
PCIE x16 1
PCIE x16 2
PCIE x1 1
PCIE x1 2
PCIE x1 3
USB controller 1
USB controller 2
USB controller 3
USB controller 4
USB controller 5
USB controller 6
USB 2.0 controller 1
USB 2.0 controller 2
SATA controller 1
SATA controller 2
ASUS Blitz Extreme
A
B
shared —
— shared
shared —
shared —
— shared
shared —
shared —
— shared
shared —
—
—
—
—
—
—
—
—
shared —
—
—
—
—
—
—
—
—
—
—
—
—
C
D
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
shared —
—
—
— shared
shared —
—
—
—
—
shared —
—
—
shared —
—
—
—
—
E
F
G
H
—
—­
—
—
—­
—
—­
—
—­
—­
—­
—
——­­
—­
—
—
—­
—­
—
—­
—­
—­
—
—­
—­
—­
—
—­
—­
—­
—
—­
—­
—­
—
—­
—­
—­
—
—­
—­
—­ shared
—­
—­
—­
—
—­
—­
—­
—
—­
—­
—­
—
—­ shared­ —­
—
—­
—­
—­
—
—­
—­
—­ shared
—­
—­
—­
—
—­
— shared —
—­
— shared —
2-21
2.5.4
PCI slots
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other
cards that comply with PCI specifications. The figure shows a LAN card installed
on a PCI slot.
2.5.5
PCI Express x1 slots
This motherboard supports PCI Express x1 network cards, SCSI cards and other
cards that comply with the PCI Express specifications.
2.5.6
•
Install the audio card on the black PCIEx1 slot prior to other compatible
cards.
•
When using PCIEx1 cards, install the cards on PCIEx1 slots prior to
PCIEx16 slots.
PCI Express x16 slots
This motherboard has two PCI Express x16 slots that support PCI Express x16
graphic cards complying with the PCI Express specifications. With two graphics
cards installed, the motherboard can enable dual‑display.
This motherboard supports two ATI CrossFire™ PCI Express x16 graphics cards
that comply with the PCI Express specifications.
•
In CrossFire™ mode, install the ATI CrossFire™ Edition (Master) graphics
card on the primary PCI Express slot.
•
Install two ATI graphics cards from the same GPU family that support
CrossFire™ mode.
Audio slot
PCI slot
PCI Express x 16 slot
PCI slot
PCI Express x 16 slot
PCI Express x 1 slot
2-22
Chapter 2: Hardware information
2.6
1.
Jumper
Clear RTC RAM (CLRTC_SW)
This jumper allows you to enable the clr CMOS switch. You can clear the CMOS
memory of date, time, and system setup parameters by erasing the CMOS RTC
RAM data. The clr CMOS switch on the back I/O helps you easily to clear the
system setup information such as system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
3.
Plug the power cord and turn ON the computer.
2.
4.
Press down the clr CMOS switch.
Hold down the <Del> key during the boot process and enter BIOS setup to
re-enter data.
Removing the cap will cause system boot failure!
clr CMOS switch behavior
System power state
Clearing CMOS
G3*
S5*
S0
S0
(DOS mode) (OS mode)
S1
S3
S4
**
*G3: Power off without +5VSB power (AC power loss); S5: Power off with +5VSB power
** The system shuts down immediately.
•
•
•
The clr CMOS switch will not function if the jumper cap on CLRTC_SW is
moved to the Disable position, but the shutdwon function in S0 mode (DOS
mode) still works.
Make sure to re-enter your previous BIOS settings after you clear the
CMOS.
You do not need to clear the RTC when the system hangs due to CPU
overclocking. With the C.P.R. (CPU Parameter Recall) feature, shut down
and reboot the system so the BIOS can automatically reset CPU parameter
settings to default values. If the system hangs due to overclocking of
memory timing or chipset voltage and the power button fails to function,
pressing down the clr CMOS switch will shut down the system and clear
CMOS simultaneously.
ASUS Blitz Extreme
2-23
2.7
EL I/O shield, LCD Poster
and Audio card Installation
2.7.1
EL I/O shield and LCD Poster Installation
1.
2.
Install the EL I/O shield to the
chassis by snaping it in place from
inside.
Orient the motherboard and install
it to the chassis. Make sure that the
motherboard external ports fit the
I/O openings.
Be cautious when installing the motherboard. The I/O shield edge springs may
damage the I/O ports.
2-24
3.
Locate the P_ELJ1 connector and 4.
connect the shield cable to the
connector in a correct orientation.
Thread the LCD Poster cable
through the back I/O shield opening
until the stopper fits the opening.
5.
Locate and connect the LCD
Poster cable to the LCD_con
connector.
Place the LCD Poster on the
chassis or to wherever you like.
6.
Chapter 2: Hardware information
2.7.2
Audio card Installation
1.
Take out the Audio card from the
package.
2.
Locate the audio slot on the
motherboard.
3.
Align the card connector with the
slot and press firmly until the card
sits on the slot completely.
4.
The photo below shows the audio
card installed on the motherboard.
ASUS Blitz Extreme
2-25
3
4
Line in
2
Front-out
1
5
6
Mic in
Rear panel connectors
7
Cen/Sub
2.8.1
8
Rear-out
Connectors
9
Side-out
2.8
10
clr
CMOS
16
1.
2.
3.
4.
15
14
13
12
11
PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
Coaxial S/PDIF Out port. This port connects an external audio output device
via a coaxial S/PDIF cable.
LAN 2 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
LAN 1 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
32-bit OS LAN port LED indications
Activity/Link
OFF
YELLOW*
YELLOW*
Speed LED
OFF
OFF
ORANGE
Description
Soft-off Mode
During Power ON/OFF
100 Mbps connection
ACT/LINK
LED
SPEED
LED
* Blinking
64-bit OS LAN port LED indications
Activity/Link
DNR
DNR
DNR
DNR
2-26
Speed LED
DNR
DNR
DNR
DNR
LAN port
Description
Soft-off Mode
During Power ON/OFF
100 Mbps connection
1 Gbps connection
Chapter 2: Hardware information
5.
6.
7.
Line In port (light blue). This port connects the tape, CD, DVD player, or
other audio sources.
Line Out port (lime). This port connects a headphone or a speaker. In
4-channel, 6-channel, and 8-channel configuration, the function of this port
becomes Front Speaker Out.
Microphone port (pink). This port connects a microphone.
8. Center/Subwoofer port (orange). This port connects the center/subwoofer
speakers.
9.
Rear Speaker Out port (black). This port connects the rear speakers on a
4-channel, 6-channel, or 8-channel audio configuration.
10. Side Speaker Out port (gray). This port connects the side speakers in an
8-channel audio configuration.
Refer to the audio configuration table below for the function of the audio ports in
2, 4, 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Light Blue
Lime
Pink
Orange
Black
Gray
Headset
2-channel
Line In
Line Out
Mic In
–
–
–
4-channel
6-channel
8-channel
Line In
Front Speaker Out
Mic In
–
Rear Speaker Out
–
Line In
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Ou
–
Line In
Front Speaker Out
Mic In
Center/Subwoofer
Rear Speaker Out
Side Speaker Out
11. USB 2.0 ports 1, 2, 3 and 4. These 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
12. External SATA port 1/2. These ports connect to external Serial ATA hard
disk drives. To configure a RAID0, RAID1, RAID 10, RAID 5 or JBOD set,
connect external Serial ATA hard disk drives to the External SATA port 1 and
2.
The external SATA port supports
external Serial ATA 3.0 Gb/s
devices. Longer cables support
higher power requirements to
deliver signal up to two meters
away, and enables improved hotswap function.
ASUS Blitz Extreme
2-27
•
Before creating a RAID set using Serial ATA hard disks, make sure that you
have connected the Serial ATA signal cable and installed Serial ATA hard
disk drives; otherwise, you cannot enter the JMicron RAID utility and SATA
BIOS setup during POST.
•
If you intend to create a RAID configuration using this connector, set the
J-Micron eSATA/PATA Controller Mode in the BIOS to [RAID]. See section
4.5.5 Onboard Device Configuration for details.
•
When using hot-plug and NCQ, set the J-Micron eSATA/PATA Controller
Mode in the BIOS to [AHCI]. See section 4.5.5 Onboard Device
Configuration for details.
•
Before creating a RAID set, refer to 5.4.3 JMicron® RAID Configuration or
the manual bundled in the motherboard support DVD.
•
DO NOT insert different connectors to the external SATA ports.
•
DO NOT unplug the external Serial ATA box when a RAID 0 or JBOD is
configured.
13. IEEE 1394a port. This 6-pin IEEE 1394a port provides high-speed
connectivity for audio/video devices, storage peripherals, PCs, or portable
devices.
14. Clear CMOS switch. Press the clear CMOS switch to clear setup information
when the system hangs due to overclocking.
15. Optical S/PDIF Out port. This port connects an external audio output device
via an optical S/PDIF cable.
16. USB 2.0 ports 5 and 6. These 4-pin Universal Serial Bus (USB) ports are
available for connecting USB 2.0 devices.
2-28
Chapter 2: Hardware information
2.8.2
1.
Internal connectors
Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable. Insert
one end of the cable to this connector, then connect the other end to the
signal connector at the back of the floppy disk drive.
®
Pin 5 on the connector is removed to prevent incorrect cable connection when
using a FDD cable with a covered Pin 5.
FLOPPY
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
BLITZ EXTREME
PIN 1
BLITZ EXTREME Floppy disk drive connector
2.
IDE connector (40-1 pin PRI_EIDE)
The onboard IDE connector is for the Ultra DMA 133/100/66 signal cable.
There are three connectors on each Ultra DMA 133/100/66 signal cable:
blue, black, and gray. Connect the blue connector to the motherboard’s IDE
connector, then select one of the following modes to configure your device.
Drive jumper setting
Single device
Two devices
Cable-Select or Master
Cable-Select
Master
Slave
Mode of
device(s)
Master
Slave
Master
Slave
Cable connector
Black
Black
Gray
Black or gray
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.
If any device jumper is set as “Cable-Select,” make sure all other device
jumpers have the same setting.
ASUS Blitz Extreme
2-29
®
PRI_EIDE
NOTE: Orient the red markings
(usually zigzag) on the IDE
cable to PIN 1.
BLITZ EXTREME
BLITZ EXTREME IDE connector
3.
ICH9R Serial ATA connectors (7-pin SATA1~6)
These connectors are for the Serial ATA signal cables for Serial ATA hard disk
drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID
1, RAID 5, RAID 10 configuration with the Intel® Matrix Storage Technology
through the onboard Intel® ICH9R RAID controller.
•
These connectors are set to Standard IDE mode by default. In Standard
IDE mode, you can connect Serial ATA boot/data hard disk drives to these
connectors. If you intend to create a Serial ATA RAID set using these
connectors, set the Configure SATA as item in the BIOS to [RAID]. See
section 4.3.6 SATA Configuration for details.
•
For RAID 5, use at least three hard disk drives. For RAID 10, use at least
four hard disk drives. Use two to four Serial ATA hard disk drives for each
RAID 0 or RAID 1 set.
•
Before creating a RAID set, refer to 5.4.2 Intel® RAID Configuration or the
manual bundled in the motherboard support DVD.
®
SATA1
SATA2
SATA5
BLITZ EXTREME
BLITZ EXTREME SATA connectors
2-30
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXP5
RSATA_RXN5
GND
GND
RSATA_TXP6
RSATA_TXN6
GND
RSATA_RXP6
RSATA_RXN6
GND
SATA3
SATA4
SATA6
Chapter 2: Hardware information
You must install the Windows® XP Service Pack 1 before using Serial ATA hard
disk drives. The Serial ATA RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is
available only if you are using Windows® XP or later version.
Connect the right-angle side
of SATA signal cable to SATA
device. Or you may connect the
right-angle side of SATA cable to
the onboard SATA port to avoid
mechanical conflict with huge
graphics cards.
USB connectors (10-1 pin USB 78, USB 9 10, USB 11 12)
These connectors are for USB 2.0 ports. Connect the USB module cable
to any of these connectors, then install the module to a slot opening at the
back of the system chassis. These USB connectors comply with USB 2.0
specification that supports up to 480 Mbps connection speed.
USB+5V
USB_P8USB_P8+
GND
NC
USB78
USB+5V
USB_P7USB_P7+
GND
USB910
USB+5V
USB_P9USB_P9+
GND
BLITZ EXTREME
USB 2.0 connectors
USB1112
USB+5V
USB_P11USB_P11+
GND
BLITZ EXTREME
USB+5V
USB_P10USB_P10+
GND
NC
USB+5V
USB_P12USB_P12+
GND
NC
®
4.
right angle side
Never connect a 1394 cable to the USB connectors. Doing so will damage the
motherboard!
You can connect the USB cable to ASUS Q-Connector (USB, blue) first, and
then install the Q-Connector (USB) to the USB connector onboard.
ASUS Blitz Extreme
2-31
IEEE 1394a port connector (10-1 pin IE1394_2)
This connector is for a IEEE 1394a port. Connect the IEEE 1394a module
cable to this connector, then install the module to a slot opening at the back
of the system chassis.
®
5.
GND
+12V
TPB1GND
TPA1-
IE1394_2
BLITZ EXTREME
PIN 1
+12V
TPB1+
GND
TPA1+
BLITZ EXTREME IEEE 1394a connector
Never connect a USB cable to the IEEE 1394a connector. Doing so will damage
the motherboard!
You can connect the 1394 cable to ASUS Q-Connector (1394, red) first, and
then install the Q-Connector (1394) to the 1394 connector onboard.
Thermal sensor cable connectors (2-pin OPT_TEMP1-2)
These connectors are for temperature monitoring. Connect the thermal
sensor cables to these connectors and place the other ends to the devices.
The OPT_TEMP connectors are for the devices that you want to monitor
temperature. The optional fans can work with the temperature sensors for a
better cooling effect.
OPT_TEMP2
BLITZ EXTREME
Temperature
Ground
®
6.
OPT_TEMP1
BLITZ EXTREME Thermal sensor cable connectors
Temperature
Ground
Remove the thermal sensor cable from the assigned device when you set this
item to [SB Overheat Protection].
2-32
Chapter 2: Hardware information
7.
CPU, chassis, and optional fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN1-4, 3-pin PWR_FAN,
3‑pin OPT_FAN1-2)
The fan connectors support cooling fans of 350 mA ~ 1000 mA (24 W max.) or
a total of 1 A ~ 3.48 A (41.76 W max.) at +12V. Connect the fan cables to the
fan connectors on the motherboard, making sure that the black wire of each
cable matches the ground pin of the connector.
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air
flow inside the system may damage the motherboard components. These are
not jumpers! DO NOT place jumper caps on the fan connectors!
®
PWR_FAN
CHA_FAN4
CHA_FAN3
CHA_FAN1
OPT_FAN1
BLITZ EXTREME
OPT_FAN2
CHA_FAN2
BLITZ EXTREME Fan connectors
CPU_FAN
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
PWR_FAN
Rotation
+12V
GND
CHA_FAN1
CHA_FAN2
CHA_FAN3
CHA_FAN4
OPT_FAN1
OPT_FAN2
Rotation
+12V
GND
Rotation
+12V
GND
GND
+12V
Rotation
CPU_FAN
Rotation
+12V
GND
Rotation
+12V
GND
Rotation
+12V
GND
•
If you install two VGA cards, we recommend that you plug the chassis fan
cable to the motherboard connector labled CHA_FAN1 or CHA_FAN2 for
better themal environment.
•
Only the CPU_FAN, CHA_FAN1-3 and OPT_FAN1-2 support ASUS Q-Fan
feature.
ASUS Blitz Extreme
2-33
8.
Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this
connector. The chassis intrusion sensor or switch sends a high-level signal to
this connector when a chassis component is removed or replaced. The signal
is then generated as a chassis intrusion event.
CHASSIS
BLITZ EXTREME
Chassis Signal
GND
+5VSB_MB
®
By default , the pin labeled “Chassis Signal” and “Ground” are shorted with
a jumper cap. Remove the jumper caps only when you intend to use the
chassis intrusion detection feature.
(Default)
BLITZ EXTREME Chassis intrusion connector
9.
ATX power connectors (24-pin EATXPWR, 8-pin EATX12V)
These connectors are for ATX power supply plugs. The power supply plugs
are designed to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
®
EATXPWR
EATX12V
BLITZ EXTREME
+12V DC
+12V DC
+12V DC
+12V DC
GND
GND
GND
GND
BLITZ EXTREME ATX power connectors
2-34
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
+5 Volts
-5 Volts
Ground
Ground
Ground
PSON#
Ground
-12 Volts
+3 Volts
•
Make sure to remove the cap on the EATX12V connector before connecting
an 8-pin EPS +12V power plug.
•
Use only an 8-pin EPS +12V power plug for the EATX12V connector.
Chapter 2: Hardware information
•
•
•
For a fully configured system, we recommend that you use a power supply
unit (PSU) that complies with ATX 12 V Specification 2.0 (or later version)
and provides a minimum power of 400 W.
Do not forget to connect the 4-pin/8pin EATX12V power plug; otherwise,
the system will not boot.
Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices. The system
may become unstable or may not boot up if the power is inadequate.
• The ATX 12 V Specification 2.0-compliant (400W) PSU has been tested
to support the motherboard power requirements with the following
configuration:
CPU: Intel® Pentium® Extreme 3.73GHz
Memory: 512 MB DDR2 (x4)
Graphics card: ASUS EAX1900XT
Parallel ATA device: IDE hard disk drive
Serial ATA device: SATA hard disk drive (x2)
Optical drive: DVD-RW
•
If you want to use two high-end PCI Express x16 cards, use a PSU with
500W to 600W power or above to ensure the system stability.
10. Digital audio connector (4-1 pin SPDIF, for ASUS HDMI VGA card)
®
This connector is for an additional Sony/Philips Digital Interface (S/PDIF)
port(s). If you are using ASUS HDMI-equipped graphics card, connect the
HDMI card to this connector with a S/PDIF out cable.
SPDIF_OUT
GND
SPDIFOUT
+5V
BLITZ EXTREME
BLITZ EXTREME Digital audio connector
The ASUS HDMI-equipped graphics card and S/PDIF out cable are purchased
separately.
ASUS Blitz Extreme
2-35
11. System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
+5V
Ground
Ground
Speaker
SPEAKER
PLED-
®
PLED+
PLED
IDE_LED
BLITZ EXTREME
Reset
Ground
PWR
Ground
IDE_LED+
IDE_LED-
PANEL
RESET
PWRSW
* Requires an ATX power supply.
BLITZ EXTREME System panel connector
2-36
•
System power LED (2-pin PLED)
•
Hard disk drive activity LED (2-pin IDE_LED)
•
System warning speaker (4-pin SPEAKER)
•
ATX power button/soft-off button (2-pin PWRSW)
•
Reset button (2-pin RESET)
This 2-pin connector is for the system power LED. Connect the chassis
power LED cable to this connector. The system power LED lights up when
you turn on the system power, and blinks when the system is in sleep mode.
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or flashes when data is
read from or written to the HDD.
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
This connector is for the system power button. Pressing the power button
turns the system on or puts the system in sleep or soft-off mode depending
on the BIOS settings. Pressing the power switch for more than four seconds
while the system is ON turns the system OFF.
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
Chapter 2: Hardware information
ASUS Q-Connector (system panel)
You can use the ASUS Q-Connector to connect/disconnect chassis front panel
cables in a few steps. Refer to the instructions below to install the ASUS QConnector.
1.
Connect the front panel cables to the
ASUS Q-Connector.
Refer to the labels on the Q-Connector
to know the detailed pin definitions, then
match them to the respective front panel
cable labels.
2.
Install the ASUS Q-Connector to the
system panel connector, making sure
the orientation matches the labels on the
motherboard.
3.
The front panel functions are now enabled.
The figure shows the Q-Connector properly
installed on the motherboard.
ASUS Blitz Extreme
2-37
2.8.3
Onboard switches
Onboard switches allow you to fine-tune performance when working on a bare
or open-case system. This is ideal for overclockers and gamers who continually
change settings to enhance system performance.
Power-on switch
Press the clear power-on switch to wake/power up the system.
®
1.
BLITZ EXTREME
BLITZ EXTREME Power on switch
Reset switch
Press the reset switch to reboot the system.
®
2.
BLITZ EXTREME
BLITZ EXTREME Reset switch
2-38
Chapter 2: Hardware information
2.8.4
Installing the optional fans
Install the optional fan only if you are using a passive cooler or a water cooler.
Installing the optional fan with an active CPU cooler will interfere with the airflow
and destabilize the system.
Optional fan on one side fins
1. Position the fan above the pipe
and heatsink assembly.
3. Carefully push down the fan until
it snugly fits the heatsink, then
connect the fan cable.
ASUS Blitz Extreme
2. Fit the fan to the grooved edge of
the heatsink.
4. The photo shows the fan installed
on the motherboard.
2-39
Optional fan on the other side fins
1. Assemble the optional fan kit
by fitting the optional fan to the
grooved edge of the plastic fan
seat and snapping it into place.
2. The photo below demostrates the
the optional fan ready for use.
3. Slide the optional fan onto the
heatsink, then connect the fan
cable.
4. The photo shows the fan installed
on the motherboard.
•
•
Plug the optional fan cables to the CHA_FAN1, CHA_FAN4 or PWR_FAN
connector on the motherboard.
Make sure the optional fan is installed correctly to prevent damage to the
fan and motherboard components.
When you are using water-cooling modules, make sure to install TWO optional
fans to obtain a more effective heat dissipation.
2-40
Chapter 2: Hardware information
2.8.5
1.
Installing the DIY Pedestal
Take out the DIY Pedestal from
the motherboard package.
2.
Arrange and stick the rubber
studs to wherever you wish to
place your motherboard.
3. Put the motherboard on the DIY
Pedestal to get a more efficient
heat dissipation.
•
•
The tape on the rubber studs is for one-time use. Replace the tape if the
adhesive surface fails to function.
You can use the DIY Pedestal in other creative ways based on your needs.
ASUS Blitz Extreme
2-41
2-42
Chapter 2: Hardware information
This chapter describes the power up
sequence, the vocal POST messages,
and ways of shutting down the system.
3
Powering up
Chapter summary
3.1
3.2
3
Starting up for the first time......................................................... 3-1
Turning off the computer.............................................................. 3-2
ASUS Blitz Extreme
3.1
Starting up for the first time
1.
After making all the connections, replace the system case cover.
3.
Connect the power cord to the power connector at the back of the system
chassis.
2.
4.
5.
6.
Be sure that all switches are off.
Connect the power cord to a power outlet that is equipped with a surge
protector.
Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power
After applying power, the system power LED on the system front panel case
lights up. For systems with ATX power supplies, the system LED lights up
when you press the ATX power button. If your monitor complies with “green”
standards or if it has a “power standby” feature, the monitor LED may light up
or switch between orange and green after the system LED turns on.
The system then runs the power-on self tests or POST. While the tests are
running, the BIOS beeps (see BIOS beep codes table below) or additional
messages appear on the screen. If you do not see anything within 30
seconds from the time you turned on the power, the system may have failed a
power-on test. Check the jumper settings and connections or call your retailer
for assistance.
BIOS Beep
One short beep
One continuous beep followed by two
short beeps then a pause (repeated)
One continuous beep followed by three
short beeps
One continuous beep followed by four
short beeps
7.
Description
VGA detected
Quick boot set to disabled
No keyboard detected
No memory detected
No VGA detected
Hardware component failure
At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the
instructions in Chapter 4.
ASUS Blitz Extreme
3-
3.2
Turning off the computer
3.2.1
Using the OS shut down function
If you are using Windows® XP:
1. Click the Start button then select Turn Off Computer.
2. Click the Turn Off button to shut down the computer.
3.
The power supply should turn off after Windows® shuts down.
If you are using Windows® Vista:
1. Click the Start button then select ShutDown.
2. The power supply should turn off after Windows® shuts down.
3.2.2
Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts
the system to sleep mode or to soft-off mode, depending on the BIOS setting.
Pressing the power switch for more than four seconds lets the system enter the
soft-off mode regardless of the BIOS setting. Refer to section 4.5 Power Menu in
Chapter 4 for details.
3-
Chapter 3: Powering up
This chapter tells how to change
the system settings through the BIOS
Setup menus. Detailed descriptions
of the BIOS parameters are also
provided.
4
BIOS setup
Chapter summary
4
4.1
Managing and updating your BIOS............................................. 4-1
4.3
Main menu................................................................................... 4-12
4.2
4.4
BIOS setup program..................................................................... 4-9
Extreme Tweaker menu.............................................................. 4-17
4.5
Advanced menu.......................................................................... 4-22
4.7
Boot menu................................................................................... 4-35
4.6
4.8
4.9
Power menu................................................................................. 4-29
Tools menu.................................................................................. 4-39
Exit menu..................................................................................... 4-41
ASUS Blitz Extreme
4.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic
Input/Output System (BIOS) setup.
1.
ASUS Update (Updates the BIOS in Windows® environment.)
3.
ASUS AFUDOS (Updates the BIOS using a bootable floppy disk.)
ASUS EZ Flash 2 (Updates the BIOS using a floppy disk or USB flash disk.)
2.
ASUS CrashFree BIOS 3 (Updates the BIOS using a bootable floppy disk,
USB flash disk or the motherboard support DVD when the BIOS file fails or
gets corrupted.)
4.
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy disk or
USB flash disk in case you need to restore the BIOS in the future. Copy the
original motherboard BIOS using the ASUS Update or AFUDOS utilities.
4.1.1
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update the
motherboard BIOS in Windows® environment. The ASUS Update utility allows you
to:
•
Save the current BIOS file
•
Update the BIOS from an updated BIOS file
•
•
•
Download the latest BIOS file from the Internet
Update the BIOS directly from the Internet, and
View the BIOS version information.
This utility is available in the support DVD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network or an
Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1.
Place the support DVD in the optical drive. The Drivers menu appears.
3.
The ASUS Update utility is copied to your system.
2.
Click the Utilities tab, then click Install ASUS Update VX.XX.XX.
ASUS Blitz Extreme
4-
Quit all Windows® applications before you update the BIOS using this utility.
Updating the BIOS through the Internet
To update the BIOS through the Internet:
4-
1.
Launch the ASUS Update utility from the Windows® desktop by clicking Start
> Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update
main window appears.
2.
Select Update BIOS from the
Internet option from the drop‑down
menu, then click Next.
3.
Select the ASUS FTP site nearest
you to avoid network traffic, or
click Auto Select. Click Next.
Chapter 4: BIOS setup
4.
5.
From the FTP site, select the BIOS
version that you wish to download.
Click Next.
Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself through
the Internet. Always update the
utility to avail all its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1.
2.
3.
4.
Launch the ASUS Update utility from the Windows® desktop by clicking Start
> Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS Update
main window appears.
Select Update BIOS from a file
option from the drop‑down menu,
then click Next.
Locate the BIOS file from the Open
window, then click Open.
Follow the screen instructions to
complete the update process.
Blitz-Extreme.rom
Blitz-Extreme
ASUS Blitz Extreme
4-
4.1.2
1.
Creating a bootable floppy disk
Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click Start from the Windows® desktop, then select My Computer.
c. Select the 3 1/2 Floppy Drive icon.
d. Click File from the menu, then select Format. A Format 3 1/2 Floppy
Disk window appears.
e. Select Create an MS-DOS startup disk from the format options field,
then click Start.
2.
4-
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click Start, then select Run.
d. From the Open field, type
D:\bootdisk\makeboot a:
assuming that D: is your optical drive.
e. Press <Enter>, then follow screen instructions to continue.
Copy the original or the latest motherboard BIOS file to the bootable floppy
disk.
Chapter 4: BIOS setup
4.1.3
ASUS EZ Flash 2 utility
The ASUS EZ Flash 2 feature allows you to update the BIOS without having to go
through the long process of booting from a floppy disk and using a DOS‑based
utility. The EZ Flash 2 utility is built-in the BIOS chip so it is accessible by pressing
<Alt> + <F2> during the Power-On Self Tests (POST).
To update the BIOS using EZ Flash 2:
1.
2.
3.
Visit the ASUS website (www.asus.com) to download the latest BIOS file for
the motherboard.
Save the BIOS file to a floppy disk or a USB flash disk, then restart the
system.
You can launch the EZ Flash 2 by two methods.
(1) Insert the floppy disk / USB flash disk that contains the BIOS file to the
floppy disk drive or the USB port.
Press <Alt> + <F2> during POST to display the following.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.05
FLASH TYPE: SST 25VF016
Current ROM
BOARD: Blitz Extreme
VER: 0122
DATE: 05/07/07
PATH: A:\
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
A:
Note
[Enter] Select or Load
[B] Backup
[Tab] Switch
[Up/Down/Home/End] Move
[ESC] Exit
(2) Enter BIOS setup program. Go to the Tools menu to select EZ Flash2
and press <Enter> to enable it.
You can switch between drives by pressing <Tab> before the correct file
is found. Then press <Enter>.
4.
When the correct BIOS file is found, EZ Flash 2 performs the BIOS update
process and automatically reboots the system when done.
•
•
This function can support devices such as USB flash disk, or floppy disk
with FAT 32/16 format and single partition only.
DO NOT shut down or reset the system while updating the BIOS to prevent
system boot failure!
ASUS Blitz Extreme
4-
4.1.4
AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment using
a bootable floppy disk with the updated BIOS file. This utility also allows you to
copy the current BIOS file that you can use as backup when the BIOS fails or gets
corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
1.
2.
•
Make sure that the floppy disk is not write-protected and has at least
1024KB free space to save the file.
•
The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be same as shown.
Copy the AFUDOS utility (afudos.exe) from the motherboard support DVD to
the bootable floppy disk you created earlier.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than eight
alphanumeric characters for the main filename and three alphanumeric
characters for the extension name.
A:\>afudos /oOLDBIOS1.rom
Main filename
3.
Extension name
Press <Enter>. The utility copies the current BIOS file to the floppy disk.
A:\>afudos /oOLDBIOS1.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
Write to file...... ok
A:\>
The utility returns to the DOS prompt after copying the current BIOS file.
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
4-
Visit the ASUS website (www.asus.com) and download the latest BIOS file for
the motherboard. Save the BIOS file to a bootable floppy disk.
Chapter 4: BIOS setup
Write the BIOS filename on a piece of paper. You need to type the exact BIOS
filename at the DOS prompt.
2.
3.
Copy the AFUDOS utility (afudos.exe) from the motherboard support DVD to
the bootable floppy disk you created earlier.
Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable floppy
disk.
A:\>afudos /iBlitz Extreme.ROM
4.
The utility verifies the file and starts updating the BIOS.
A:\>afudos /iBlitz Extreme.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to prevent
system boot failure!
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iBlitz Extreme.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... done
Verifying flash .... done
Please restart your computer
A:\>
ASUS Blitz Extreme
4-
4.1.5
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore
the BIOS file when it fails or gets corrupted during the updating process. You can
update a corrupted BIOS file using the motherboard support DVD, the floppy disk,
or the USB flash disk that contains the updated BIOS file.
Prepare the motherboard support DVD, the floppy disk or the USB flash disk
containing the updated motherboard BIOS before using this utility.
Recovering the BIOS from the support DVD
To recover the BIOS from the support DVD:
1.
Turn on the system.
3.
The utility displays the following message and automatically checks the DVD
for the BIOS file.
2.
Insert the motherboard support DVD to the optical drive.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and starts flashing the corrupted
BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “Blitz Extreme.ROM”. Completed.
Start flashing...
4.
Restart the system after the utility completes the updating process.
Recovering the BIOS from the USB flash disk
To recover the BIOS from the USB flash disk:
1.
Insert the USB flash disk that contains BIOS file to the USB port.
3.
The utility will automatically checks the devices for the BIOS file When found,
the utility reads the BIOS file and starts flashing the corrupted BIOS file.
2.
4.
4-
Turn on the system.
Restart the system after the utility completes the updating process.
•
Only the USB flash disk with FAT 32/16 format and single partition can
support ASUS CrashFree BIOS 3. The device size should be smaller than
8GB.
•
DO NOT shut down or reset the system while updating the BIOS! Doing so
can cause system boot failure!
Chapter 4: BIOS setup
4.2
BIOS setup program
This motherboard supports a programmable Serial Peripheral Interface (SPI) chip
that you can update using the provided utility described in section 4.1 Managing
and updating your BIOS.
Use the BIOS Setup program when you are installing a motherboard, reconfiguring
your system, or prompted to “Run Setup.” This section explains how to configure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
configuration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to reconfigure your system using the BIOS Setup program so that the
computer can recognize these changes and record them in the CMOS RAM of the
SPI chip.
The SPI chip on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. Press
<Del> during the Power-On Self-Test (POST) to enter the Setup utility; otherwise,
POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make
your selections from the available options using the navigation keys.
•
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Select the Load Setup Defaults item under the
Exit Menu. See section 4.9 Exit Menu.
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS file for
this motherboard.
ASUS Blitz Extreme
4-
4.2.1
BIOS menu screen
Menu items
Main
Menu bar
Extreme Tweaker
Configuration fields
BIOS SETUP UTILITY
Advanced
Power
Boot
System Time
System Date
Legacy Diskette A
Language
SATA
SATA
SATA
SATA
SATA
SATA
1
2
3
4
5
6
General help
Tools
[10:55:25]
[Thu 05/10/2007]
[1.44M, 3.5 in]
[English]
[Not
[Not
[Not
[Not
[Not
[Not
Detected]
Detected]
Detected]
Detected]
Detected]
Detected]
SATA Configuration
System Information
Exit
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Use [+] or [-] to
configure system Time.
Select Screen
Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Sub-menu items
4.2.2
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Advanced
For changing the advanced system settings
Extreme Tweaker For changing the overclocking settings
Power
For changing the advanced power management (APM)
configuration
Tools
For configuring options for special functions
Boot
Exit
For changing the system boot configuration
For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that
particular menu. Use the navigation keys to select items in the menu and change
the settings.
Some of the navigation keys differ from one screen to another.
4-10
Chapter 4: BIOS setup
4.2.4
Menu items
The highlighted item on the menu bar
displays the specific items for that
menu. For example, selecting Main
shows the Main menu items.
The other items (Advanced, Power,
Boot, and Exit) on the menu bar have
their respective menu items.
4.2.5
Sub-menu items
System Time
System Date
Legacy Diskette A
Language
SATA
SATA
SATA
SATA
SATA
SATA
Use [ENTER], [TAB],
or [SHIFT-TAB] to
select a field.
[06:22:54]
[Thu 05/10/2007]
[1.44M, 3.5 in]
[English]
1
2
3
4
5
6
[Not
[Not
[Not
[Not
[Not
[Not
Use [+] or [-] to
configure system.
Detected]
Detected]
Detected]
Detected]
Detected]
Detected]
SATA Configuration
System Information
Main menu items
A solid triangle before each item on any menu screen means that the iteam has a
sub-menu. To display the sub-menu, select the item and press <Enter>.
4.2.6
Configuration fields
These fields show the values for the menu items. If an item is user- configurable,
you can change the value of the field opposite the item. You cannot select an item
that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To
change the value of a field, select it then press <Enter> to display a list of options.
Refer to 4.2.7 Pop-up window.
4.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the
configuration options for that item.
4.2.8
Scroll bar
A scroll bar appears on the right side of a
menu screen when there are items that do
not fit on the screen. Press the
Up/Down arrow keys or <Page Up> /<Page
Down> keys to display the other items on
the screen.
4.2.9
General help
At the top right corner of the menu screen
is a brief description of the selected item.
ASUS Blitz Extreme
Pop-up window
Scroll bar
4-11
4.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving
you an overview of the basic system information.
Refer to section 4.2.1 BIOS menu screen for information on the menu screen
items and how to navigate through them.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
System Time
System Date
Legacy Diskette A
Language
SATA
SATA
SATA
SATA
SATA
SATA
1
2
3
4
5
6
[10:55:25]
[Thu 05/10/2007]
[1.44M, 3.5 in]
[English]
[Not
[Not
[Not
[Not
[Not
[Not
Detected]
Detected]
Detected]
Detected]
Detected]
Detected]
SATA Configuration
System Information
Tools
Exit
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Use [+] or [-] to
configure system Time.
Select Screen
Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
4.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed.
Configuration options: [Disabled] [720K , 3.5 in.] [1.44M, 3.5 in.]
4.3.4
Language [English]
Allows you to choose the BIOS language version from the options.
Configuration options: [Chinese BIG5] [Chinese (GB)] [Japanese] [Français]
[German] [English]
4-12
Chapter 4: BIOS setup
4.3.5
SATA 1-6
While entering Setup, the BIOS automatically detects the presence of Serial ATA
devices. There is a separate sub-menu for each SATA device. Select a device item
then press <Enter> to display the SATA device information.
BIOS SETUP UTILITY
Main
SATA 1
Device
:Not Detected
Select the type of
device connected to
the system.
Type
[Auto]
LBA/Large Mode
[Auto]
Block(Multi-Sector Transfer)[Auto]
PIO Mode
[Auto]
DMA Mode
[Auto]
SMART Monitoring
[Auto]
32Bit Data Transfer
[Enabled]
+-
F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
The BIOS automatically detects the values opposite the dimmed items (Device,
Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and
SMART monitoring). These values are not user-configurable. These items show
N/A if no SATA device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to [Auto] allows automatic selection of the
appropriate IDE device type. Select [CDROM] if you are specifically configuring a
CD-ROM drive. Select [ARMD] (ATAPI Removable Media Device) if your device is
either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Auto]
Block (Multi-sector Transfer) [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the data
transfer from and to the device occurs multiple sectors at a time if the device
supports multi-sector transfer feature. When set to [Disabled], the data transfer
from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
ASUS Blitz Extreme
4-13
DMA Mode [Auto]
Selects the DMA mode.
Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0]
[MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
4.3.6
SATA Configuration
The items in this menu allow you to set or change the configurations for the SATA
devices installed in the system. Select an item then press <Enter> if you want to
configure the item.
SATA Configuration
SATA Configuraton
Configure SATA as
[Enhanced]
[IDE]
Hard Disk Write Protect
IDE Detect Time Out (Sec)
[Disabled]
[35]
Set [Compatible Mode]
when Legacy OS (i.e.
WIN ME, 98, NT4.0, MS
DOS) is used.
Set [Enhanced Mode]
when Native OS (i.e.
WIN2000, WIN XP, Vista
is used.
SATA Configuration [Enhanced]
Configuration options: [Disabled] [Compatible] [Enhanced]
Configure SATA as [IDE]
Sets the configuration for the Serial ATA connectors supported by the
Southbridge chip.
The AHCI allows the onboard storage driver to enable advanced Serial
ATA features that increases storage performance on random workloads by
allowing the drive to internally optimize the order of commands.
If you want to create a RAID 0, RAID 1, RAID 5, RAID 10, or the Intel®
Matrix Storage Technology configuration from the Serial ATA hard disk drives,
set this item to [RAID].
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, keep the default setting [IDE].
If you want the Serial ATA hard disk drives to use the Advanced Host Controller
Interface (AHCI), set this item to [AHCI].
4-14
Chapter 4: BIOS setup
Intel Robson Technology [Disabled]
Allows you to enable or disable Intel Robson Technology.
Configuration option: [Disabled] [Enabled]
The Intel Robson Technology appears only when you set the item Configure
SATA as to [AHCI].
Hard Disk Write Protect [Disabled]
Disables or enables device write protection. This will be effective only if device is
accessed through BIOS. Confiuration option: [Disabled] [Enabled]
IDE Detect Time Out (Sec) [35]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
4.3.7
AHCI Configuration
This menu allows you to configure AHCI settings. It appears only when you set the
Configure SATA as item to [AHCI] in the SATA Configuration menu.
While entering setup,
BIOS auto detects
the presence of SATA
devices. This displays
the status of auto
detection of SATA
devices.
AHCI Settings
AHCI
AHCI
AHCI
AHCI
AHCI
AHCI
Port1
Port2
Port3
Port4
Port5
Port6
[Not
[Not
[Not
[Not
[Not
[Not
Detected]
Detected]
Detected]
Detected]
Detected]
Detected]
ACHI Port1~6 [XXXX]
Displays the status of auto-detection of SATA devices.
AHCI Port1
Device
:Not Detected
SATA Port1
Select the type of
devices connected to
the system.
[Auto]
SATA Port1 [Auto]
Allows you to select the type of device connected to the system.
Configuration options: [Auto] [Not Installed]
ASUS Blitz Extreme
4-15
4.3.8
System Information
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
BIOS SETUP UTILITY
Main
AMIBIOS
Version
: 0122
Build Date : 05/07/07
Processor
Type
Speed
Count
: Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz
: 1876MHz
: 2
System Memory
Available
: 512 MB
Select Screen
Select Item
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
4-16
Chapter 4: BIOS setup
4.4
Extreme Tweaker menu
The Extreme Tweaker menu items allow you to configure overclocking-related
items.
Take caution when changing the settings of the Extreme Tweaker menu items.
Incorrect field values can cause the system to malfunction.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
Configure System Frequency/Voltage
Ai Overclocking
CPU Ratio Control
DRAM Frequency
DRAM Timing Control
DRAM Static Read Control
DRAM Dynamic Write Control
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
Transaction Booster
Clock Over-Charging Mode
[Auto]
[Auto]
CPU Spread Spectrum PCIE Spread Spectrum
[Auto]
[Auto]
Tools
Exit
Select the target CPU
frequency, and the
relevant parameters
will be auto-adjusted.
Frequencies higher
than CPU manufacturer
recomends are not
guaranteed to be
stable. If the system
becomes unstable,
return to the default.
+-
Tab
F1
F10
ESC
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.4.1
Ai Overclocking [Auto]
Allows selection of CPU overclocking options to achieve desired CPU internal
frequency. Selct either one of the preset overclocking configuration options:
Manual
Allows you to individually set overclocking parameters.
Auto
Loads the optimal settings for the system.
Standard
Loads the standard settings for the system.
N.O.S.
The ASUS Non-delay Overclocking System feature intelligently
determines the system load and automatically boosts the
performance for the most demanding tasks.
The following item only appears when you set the Ai Overclocking item to
[N.O.S].
N.O.S. Mode [Auto]
Configuration options: [Auto] [Standard] [Sensitive] [Heavy Load]
CPU Ratio Control [Auto]
Allows you to control the CPU ratio. Configuration options: [Auto] [Manual]
The following item only appears when you set the CPU Ratio Control item to
[Manual].
ASUS Blitz Extreme
4-17
Ratio CMOS Setting [7]
Configuration options: [6] [7]
The following two items only appear when you set the Ai Overclocking item to
[Manual].
FSB Frequency [266]
Displays the frequency sent by the clock generator to the system bus and PCI bus.
The value of this item is auto-detected by the BIOS. Use the <+> and <-> keys to
adjust the FSB frequency. You can also type the desired CPU frequency using the
numeric keypad. The values range from 200 to 800. Refer to the table below for
the correct Front Side Bus and CPU External Frequency settings.
FSB/CPU External Frequency Synchronization
Front Side Bus
CPU External Frequency
FSB 1333
333 MHz
FSB 1066
266 MHz
FSB 800
200 MHz
Refer to page 2-3 for FSB frequency LED definition.
PCIE Frequency [Auto]
Allows you to set the PCI Express frequency.
Configuration options: [Auto] [100] [101]~[149] [150]
DRAM Frequency [Auto]
Allows you to set the DDR3 operating frequency.
Configuration options: [Auto] [DDR3-800MHz] [DDR3-889 MHz] [DDR3-1067MHz]
A very high DRAM frequency may cause the system to become unstable! If this
happens, revert to the default setting.
DRAM Timing Control [Auto]
Configuration options: [Auto] [Manual]
The following items appear when you set the DRAM Timing Control item to
[Manual].
CAS# Latency [ 6]
Configuration options: [5] [6] [7] [8] [9] [10]
RAS# to CAS# Delay [ 5 DRAM Clocks]
Configuration options: [3 DRAM Clocks] [4 DRAM Clocks]~[9 DRAM Clocks]
[10 DRAM Clocks]
4-18
Chapter 4: BIOS setup
RAS# Precharge [ 5 DRAM Clocks]
Configuration options: [ 3 DRAM Clocks] [ 4 DRAM Clocks]~[ 9 DRAM
Clocks] [10 DRAM Clocks]
RAS# Activate to Precharge [ 9 DRAM Clocks]
Configuration options: [ 3 DRAM Clocks] [ 4 DRAM Clocks]~[33 DRAM
Clocks] [34 DRAM Clocks]
TWR [Auto]
Configuration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRFC [Auto]
Configuration options: [Auto] [30 DRAM Clocks] [36 DRAM Clocks]
[48 DRAM Clocks] [60 DRAM Clocks] [72 DRAM Clocks]
TWTR [Auto]
Configuration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRRD [Auto]
Configuration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
TRTP [Auto]
Configuration options: [Auto] [ 1 DRAM Clocks]~[15 DRAM Clocks]
DRAM Static Read Control [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
DRAM Dynamic Write Control [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
Transaction Booster [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
Boost Level [0]
Set this time to higher level to get better performance. This item is available
only when you set the Transaction Booster item to [Enabled].
Configuration options: [0] [1]
Clock Over-Charging Mode [Auto]
Configuration options: [Auto] [700mV] [800mV] [900mV] [1000mV]
CPU Spread Spectrum [Auto]
Allows you to enable or disable the CPU spread spectrum.
Configuration options: [Auto] [Disabled]
PCIE Spread Spectrum [Auto]
Allows you to enable or disable the PCIE spread spectrum.
Configuration options: [Auto] [Disabled]
ASUS Blitz Extreme
4-19
The following item only appears when you set the Ai Overclocking item to
[Manual] or [N.O.S.].
CPU Voltage [Auto]
Allows you to select the CPU VCore voltage. The text color in the configuration
field corresponds to the onboard CPU LED color, both of which indicate CPU
voltage condition. Refer to page 2-1 for CPU LED definition.
Configuration options: [Auto] [1.10000V] [1.10625V] [1.11250V] [1.11875V]
[1.12500V] [1.13125V] [1.13750V] [1.14375V] [1.50000V] [1.15625V] [1.16250V]
[1.16875V] [1.17500V] [1.18125V] [1.18750V] [1.19375V] [1.20000V] [1.20625V]
[1.21250V] [1.21875V] [1.22500V] [1.23125V] [1.23750V] [1.24375V] [1.25000V]
[1.25625V] [1.26250V] [1.26875V] [1.27500V] [1.28125V] [1.28750V] [1.29375V]
[1.30000V]~[1.80000V] [1.80625V] [1.81250V] [1.81875V] [1.82500V] [1.83125V]
[1.83750V] [1.84375V] [1.85000V] [1.85625V] [1.86250V] [1.86875V] [1.87500V]
[1.88125V] [1.88750V] [1.89375V] [1.90000V]
Refer to the CPU documentation before setting the CPU Vcore voltage. Setting
a high VCore voltage may damage the CPU permanently, and setting a low
VCore voltage may make the system unstable.
CPU Voltage Reference [Auto]
Configuration options: [Auto] [0.531V] [0.545V] [0.561V] [0.576V] [0.581V] [0.597V]
[0.618V] [0.635V]
Loadline Calibration [Auto]
Configuration options: [Auto] [Disabled] [Enabled]
FSB Termination Voltage [Auto]
Allows you to select the front side bus (FSB) termination voltage. The text color
in the configuration field indicates FSB termination voltage condition. When you
set the NB LED Selection item to [FSBT Volt], the onboard northbridge LED
displays FSB termination voltage condition. Refer to page 2-2 for northbridge LED
definition.
Configuration options: [Auto] [1.20V] [1.22V] [1.24V] [1.26V] [1.28V] [1.30V]~
[1.70V] [1.72V] [1.74V] [1.76V] [1.78V] [1.80V]
Setting a high FSB termination voltage may damage the chipset and CPU.
North Bridge Voltage [Auto]
Allows you to select the northbridge voltage. The text color in the configuration field
indicates northbridge voltage condition. When you set the NB LED Selection item
to [NB Volt], the onboard northbridge LED displays northbridge voltage condition.
Refer to page 2-2 for northbridge LED definition.
Configuration options: [Auto] [1.25V] [1.27V] [1.29V] [1.31V]~[1.97V] [1.99V]
[2.01V] [2.03V]
4-20
Chapter 4: BIOS setup
North Bridge Voltage Refernece [Auto]
Configuration options: [Auto] [0.61x] [0.67x]
DRAM Voltage [Auto]
Allows you to select the DRAM reference voltage. The text color in the
configuration field corresponds to the onboard memory LED color, both of which
indicate DRAM voltage condition. Refer to page 2-2 for memory LED definition.
Configuration options: [Auto] [1.50V] [1.52V] [1.54V] [1.56V] [1.58V] [1.60V]~
[3.00V] [3.02V] [3.04V]
DDR3 Channel A REF Voltage [Auto]
Allows you to manually set the memory voltage, or you can set to [Auto] for the
safe mode.
Configuration options: [DDR3_REF-30mv] [DDR3_REF-20mv] [DDR3_REF-10mv]
[DDR3_REF] [DDR3_REF+10mv] [DDR3_REF+20mv] [DDR3_REF+30mv]
DDR3 Channel B REF Voltage [Auto]
Allows you to manually set the memory voltage, or you can set to [Auto] for the
safe mode.
Configuration options: [DDR3_REF-30mv] [DDR3_REF-20mv] [DDR3_REF-10mv]
[DDR3_REF] [DDR3_REF+10mv] [DDR3_REF+20mv] [DDR3_REF+30mv]
DDR3 Controller REF Voltage [Auto]
Allows you to manually set the memory voltage, or you can set to [Auto] for the
safe mode.
Configuration options: [DDR3_REF-30mv] [DDR3_REF-20mv] [DDR3_REF-10mv]
[DDR3_REF] [DDR3_REF+10mv] [DDR3_REF+20mv] [DDR3_REF+30mv]
South Bridge Voltage [Auto]
Allows you to select the southbridge voltage. The text color in the configuration
field indicates southbridge voltage condition. When you set the SB LED Selection
item to [SB Volt], the onboard southbridge LED displays southbridge voltage
condition. Refer to page 2-2 for southbridge LED definition.
Configuration options: [Auto] [1.050V] [1.075V] [1.110V] [1.125V] [1.150V] [1.175V]
[1.200V] [1.225V]
PLL Voltage [Auto]
Allows you to select the southbridge voltage. The text color in the configuration
field indicates southbridge voltage condition. When you set the SB LED Selection
item to [SB Volt], the onboard southbridge LED displays southbridge voltage
condition. Refer to page 2-2 for southbridge LED definition.
Configuration options: [Auto] [1.50V] [1.52V] [1.56V] [1.58V] [1.60V]~[1.92V]
[1.94V] [1.96V] [1.98V] [2.00V]
ASUS Blitz Extreme
4-21
NB LED Selection [NB Volt]
Allows you to switch the onboard northbridge LED display between northbridge
voltage [NB Volt] and front side bus termination voltage [FSBT Volt].
Configuration options: [NB Volt] [FSBT Volt]
SB LED Selection [PLL Volt]
Allows you to switch the onboard southbridge LED display between PLL voltage
[PLL Volt] and southbridge voltage [SB Volt].
Configuration options: [PLL Volt] [SB Volt]
4.5
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
Ai Net 2
USB Configuration
Tools
Exit
LAN Cable Status.
CPU Configuration
Chipset
Onboard Devices Configuration
PCIPnP
Select Screen
Select Item
+- Change Field
Tab Select Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4-22
Chapter 4: BIOS setup
4.5.1
Ai Net 2
BIOS SETUP UTILITY
Advanced POST Check LAN cable[Disabled]
Ai Net 2
Pair Status
1-2
N/A
3-6
N/A
4-5
N/A
7-8
N/A
1-2
3-6
4-5
7-8
Check LAN cable during
POST.
Length
N/A
N/A
N/A
N/A
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
POST Check LAN cable [Disabled]
Enables or disables the LAN cable checking during the POST.
Configuration options: [Disabled] [Enabled]
4.5.2
USB Configuration
The items in this menu allows you to change the USB-related features. Select an
item then press <Enter> to display the configuration options.
BIOS SETUP UTILITY
Advanced
USB Configuration
Options
USB Devices Enabled:
None
USB Functions
USB 2.0 Controller
USB 2.0 Controller Mode
BIOS EHCI Hand-off
Port 64/60 Emulation
Legacy USB Support Disabled
Enabled
[Enabled]
[Enabled]
[HiSpeed]
[Enabled]
[Disabled]
[Auto]
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
The USB Devices Enabled item shows the auto-detected values. If no USB
device is detected, the item shows None.
USB Functions [Enabled]
Allows you to enable or disable the USB functions. The following sub-items appear
when this item is set to [Enabled]. Configuration options: [Disabled] [Enabled]
ASUS Blitz Extreme
4-23
The following items appear only when you set USB Functions to [Enabled].
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed] [HiSpeed]
The USB 2.0 Controller Mode item appears only when you enable the USB
2.0 Controller.
BIOS EHCI Hand-off [Enabled]
Allows you to enable the support for operating systems without an EHCI hand‑off
feature. Configuration options: [Disabled] [Enabled]
Port 64/60 Emulation [Disabled]
Allows you to enable or disable the I/O port 60h/64h emulation support. This item
should be enabled for the complete USB keyboard legacy support for non-USB
aware OSes. Configuration options: [Disabled] [Enabled]
Legacy USB Support [Auto]
Allows you to enable or disable the support for legacy USB devices. Setting to
[Auto] allows the system to detect the presence of USB devices at startup. If
detected, the USB controller legacy mode is enabled. If no USB device is detected,
the legacy USB support is disabled.
Configuration options: [Disabled] [Enabled] [Auto]
4-24
Chapter 4: BIOS setup
4.5.3
CPU Configuration
The items in this menu show the CPU-related information that the BIOS
automatically detects.
BIOS SETUP UTILITY
Advanced
Configure Advanced CPU settings
Manufacturer:Intel
Brand String:Intel(R) Core(TM)2 CPU 6300 @ 1.86GHz
Frequency
:1.86GHz
FSB Speed
:1066 MHz
Cache L1
:64 KB
Cache L2
:2048 KB
CPUID
:6F5
Ratio Status:Unlocked (Max:07, Min:06)
Ratio Actual Value: 7
CPU Ratio Control [Auto]
C1E Support [Enabled]
Max CPUID Value Limit [Disabled]
Vanderpool Technology [Enabled]
CPU TM Function [Enabled]
Execute Disable Bit [Enabled]
PECI
[Enabled]
Intel(R) SpeedStep(tm) Tech.[Disabled]
Options
Auto
Manual
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
CPU Ratio Control [Auto]
Configuration options: [Auto] [Manual]
The following item appears when the item CPU Ratio Control is set to
[Manual].
Ratio CMOS Setting: [ 7]
C1E Support [Enabled]
Allows you to enable or disable C1E Support.
Configuration options: [Enabled] [Disabled]
Max CPUID Value Limit [Disabled]
Setting this item to [Enabled] allows legacy operating systems to boot even without
support for CPUs with extended CPUID functions.
Configuration options: [Disabled] [Enabled]
Vanderpool Technology [Enabled]
Configuration options: [Enabled] [Disabled]
CPU TM Function [Enabled]
Configuration options: [Disabled] [Enabled]
Execute Disable Bit [Enabled]
Allows you to enable or disable the No-Execution Page Protection Technology.
Setting this item to [Disabled] forces the XD feature flag to always return to zero
(0). Configuration options: [Disabled] [Enabled]
ASUS Blitz Extreme
4-25
PECI [Enabled]
Allows you to enable or disable the PECI interface.
Configuration options: [Enabled] [Disabled]
The following item appears when the item CPU Ratio Control is set to [Auto].
Intel(R) SpeedStep (tm) Tech. [Disabled]
Configuration options: [Enabled] [Disabled]
4.5.4
Chipset
The Chipset menu allows you to change the advanced chipset settings. Select an
item then press <Enter> to display the sub-menu.
BIOS SETUP UTILITY
Advanced
Advanced Chipset Settings
WARMING: Setting wrong values in below sections
may cause system to malfunction.
North Bridge Configuration
Configure North Bridge features.
North Bridge Chipset Configuration
BIOS SETUP UTILITY
Advanced
North Bridge Chipset Configuration
Memory Remap Feature
[Enabled]
Initiate Graphic Adapter [PEG/PCI]
PEG Port Control
[Auto]
ENABLE: Allow
remapping of
overlapped PCI memory
above the total
physical memory.
DISABLE: Do not allow
remapping of memory.
Memory Remap Feature [Enabled]
Allows you to enable or disable the remapping of the overlapped PCI memory
above the total physical memory. Enable this option only when you install 64bit operating system. Configuration options: [Disabled] [Enabled]
Initiate Graphic Adapter [PEG/PCI]
Allows you to decide which graphics controller to use as the primary boot
device. Configuration options: [PCI/PEG] [PEG/PCI]
PEG Port Control [Auto]
Configuration options: [Auto] [Disabled]
4-26
Chapter 4: BIOS setup
4.5.5
OnBoard Devices Configuration
BIOS SETUP UTILITY
Advanced
Onboard Device Configuration
J-Micron eSATA/PATA Controller
Controller Mode
Marvell Gigabit LAN 1
LAN Boot ROM
Marvell Gigabit LAN 2
LAN Boot ROM
VIA Firewire 1394
Options
[Enabled]
[IDE]
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Enabled]
Enabled
Disabled
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
J-Micron eSATA/PATA Controller [Enabled]
Configuration options: [Enabled] [Disabled]
Controller Mode [IDE]
Configuration options: [RAID] [IDE] [AHCI]
Marvell Gigabit LAN 1 [Enabled]
Configuration options: [Enabled] [Disabled]
LAN Boot ROM [Disabled]
Configuration options: [Disabled] [Enabled]
MarvelI Gigabit LAN 2 [Enabled]
Configuration options: [Enabled] [Disabled]
LAN Boot ROM [Disabled]
Configuration options: [Disabled] [Enabled]
VIA Firewire 1394 [Enabled]
Configuration options: [Enabled] [Disabled]
ASUS Blitz Extreme
4-27
4.5.6
PCI PnP
The PCIPnP menu items allow you to change the advanced settings for PCI/PnP
devices.
Take caution when changing the settings of the PCI PnP menu items. Incorrect
field values can cause the system to malfunction.
BIOS SETUP UTILITY
Advanced
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
[NO]
NO: lets the BIOS
configure all the
devices in the system.
YES: lets the
operating system
configure Plug and Play
(PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
Select Screen
Select Item
+Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Plug And Play O/S [NO]
When set to [NO], BIOS configures all the devices in the system. When set to
[YES] and if you install a Plug and Play operating system, the operating system
configures the Plug and Play devices not required for boot.
Configuration options: [NO] [YES]
4-28
Chapter 4: BIOS setup
4.6
Power menu
The Power menu items allow you to change the settings for the Advanced
Power Management (APM). Select an item then press <Enter> to display the
configuration options.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
Suspend Mode
Repost Video on S3 Resume
ACPI 2.0 Support
ACPI APIC Support
[Auto]
[Disabled]
[Disabled]
[Enabled]
Tools
Exit
Select the ACPI state
used for System
Suspend.
APM Configuration
Hardware Monitor
Select Screen
Select Item
+Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.6.1
Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface (ACPI) state
to be used for system suspend.
Configuration options: [S1 (POS) Only] [S3 Only] [Auto]
4.6.2
Repost Video on S3 Resume [Disabled]
Determines whether to invoke VGA BIOS POST on S3/STR resume.
Configuration options: [Disabled] [Enabled]
4.6.3
ACPI 2.0 Support [Enabled]
Specifies the Advanced Configuration and Power Interface (ACPI) version
supported. Configuration options: [Disabled] [Enabled]
4.6.4
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power Interface
(ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When
set to Enabled, the ACPI APIC table pointer is included in the RSDT pointer list.
Configuration options: [Disabled] [Enabled]
ASUS Blitz Extreme
4-29
4.6.5
APM Configuration
BIOS SETUP UTILITY
Power
APM Configuration
Restore on AC Power Loss
Power On By RTC Alarm
Power On By PCI Devices
Power On By PCIE Devices
Power On By PS/2 Keyboard
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
<Enter> to select
whether or not to
restart the system
after AC power loss.
+-
F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Restore On AC Power Loss [Power Off]
When set to [Power Off], the system goes into off state after an AC power loss.
When set to [Power On], the system goes on after an AC power loss. When set to
[Last State], the system goes into either off or on state, whatever the system state
was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. When this item is
set to Enabled, the items RTC Alarm Date/ RTC Alarm Hour/ RTC Alarm Minute/
RTC Alarm Second will become user-configurable with set values.
Configuration options: [Disabled] [Enabled]
Power On By PCI Devices [Disabled]
Allows you to enable or disable the PME to wake up from S5 by PCI devices.
Configuration options: [Disabled] [Enabled]
Power On By PCIE Devices [Disabled]
Allows you to enable or disable the PCIE devices to generate a wake event.
Configuration options: [Disabled] [Enabled]
Power On By PS/2 Keyboard [Disabled]
Allows you to disable the Power On by PS/2 keyboard function or set specific keys
on the PS/2 keyboard to turn on the system. This feature requires an ATX power
supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key]
4-30
Chapter 4: BIOS setup
4.6.6
Hardware Monitor
BIOS SETUP UTILITY
Power
Hardware Monitor
CPU Temperature
MB Temperature
NB Temperature
SB Temperature
OPT Temperature
CPU Temperature
[30.5ºC/86.5ºF]
[35ºC/95ºF]
[34ºC/94ºF]
[42ºC/107.5ºF]
[N/A]
North Bridge Overheat Protecti[Auto]
South Bridge Sensor Select
[SB Overheat Protec]
South Bridge Overheat Protecti[Auto]
OPT_TEMP1 Overheat Protection [Disabled]
CPU Fan and Chassis Fan
OPT Fan and Power Fan
+-
F1
F10
ESC
Select Screen
Select Item
Change Field
General Help
Save and Exit
Exit
+-
F1
F10
ESC
Select Screen
Select Item
Change Field
General Help
Save and Exit
Exit
VCORE Voltage
[ 1.280V]
FSB Termination Voltage
[ 1.232V]
North Bridge Voltage
[ 1.280V]
DRAM Voltage
[ 1.584V]
v02.58 (C)Copyright 1985-2006,
1985-2007, American Megatrends, Inc.
Scroll down to see more items.
DRAM Reference Voltage
South Bridge Voltage
PLL Voltage
3.3V Voltage
5V
Voltage
12V Voltage
[ 1.584V]
[ 1.072V]
[ 1.520V]
[ 3.200V]
[ 5.040V]
[12.152V]
v02.58 (C)Copyright 1985-2006,
1985-2007, American Megatrends, Inc.
CPU Temperature; MB Temperature; NB Temperature
SB Temperature; OPT Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU,
motherboard, northbridge, southbridge and the assigned device temperatures.
Select [Ignored] if you do not wish to display the detected temperatures.
North Bridge Overheat Protection [Auto]
Allows you to enable/disable the northbridge overheat auto-protection function or
set the temperature over which the system shuts down.
Configuration options: [Auto] [70C] [80C] [Disabled]
South Bridge Sensor Select [SB Overheat Protection]
Allows you to switch the target the temperature sensor aims at between the
southbridge and any device with a thermal sensor cable connected to the
OPT_TEMP2 connector.
Configuration options: [SB Overheat Protection] [OPT_TEMP2]
Remove the thermal sensor cable from the assigned device when you set this
item to [SB Overheat Protection].
The next item varies depending on whether you set the South Bridge Sensor
Select item to [SB Overheat Protection] or [OPT_TEMP2].
ASUS Blitz Extreme
4-31
South Bridge Overheat Protection [Auto]
Allows yous to enable/disable the southbridge overheat auto-protection function or
set the temperature over which the system shuts down.
Configuration options: [Auto] [70C] [80C] [Disabled]
OPT_TEMP2 Overheat Protection [Disabled]
If you monitor a device temperature using a thermal sensor cable connected to the
OPT_TEMP2 connector, you can use this item to set the temperature over which
the system shuts down or disable this function.
Configuration options: [Disabled] [50C] [60C] [70C] [80C] [90C]
OPT_TEMP1 Overheat Protection [Disabled]
If you monitor a device temperature using a thermal sensor cable connected to the
OPT_TEMP1 connector, you can use this item to set the temperature over which
the system shuts down or disable this function.
Configuration options: [Disabled] [50C] [60C] [70C] [80C] [90C]
CPU Fan and Chassis Fan
BIOS SETUP UTILITY
Power
CPU Fan Speed
CPU Q-Fan Control
Chassis Fan 1 Speed
Chassis Fan 2 Speed
Chassis Fan 3 Speed
Chassis Q-Fan Control
Chassis Fan 4 Speed
[4411RPM]
[Disabled]
[N/A]
[N/A]
[N/A]
[N/A]
:N/A
CPU Fan Speed
Select Screen
Select Item
+- Change Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
CPU Fan Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A.
CPU Q-Fan Control [Disabled]
Allows you to enable or disable the CPU Q-Fan controller.
Configuration options: [Disabled] [Enabled]
Chassis Fan 1/2/3 Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the
chassis fan speed in rotations per minute (RPM). If the fan is not connected
to the motherboard, the field shows N/A.
4-32
Chapter 4: BIOS setup
Chassis Q-Fan Control [Disabled]
Allows you to enable or disable the chassis Q-Fan controller.
Configuration options: [Disabled] [Enabled]
The following two items appear when you enable the Chassis Q-Fan Control
feature.
Chassis Fan Ratio [Auto]
Configuration options: [Auto] [90%] [80%] [70%] [60%]
Chassis Target Temperature [21ºC]
Configuration options: [12ºC] [15ºC] [18ºC] [21ºC] [24ºC] [27ºC] [30ºC]
Chassis Fan 4 Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the
chassis fan speed in rotations per minute (RPM). If the fan is not connected
to the motherboard, the field shows N/A.
OPT Fan and Power Fan
BIOS SETUP UTILITY
Power
OPT_Fan 1 Speed
OPT_Fan1 Q-Fan Control
Duty Cycle Mode
OPT_Fan 2 Speed
OPT_Fan2 Q-Fan Control
Duty Cycle Mode
Power Fan Speed
:N/A
[DUTY CYCLE]
[90%]
:N/A
[DUTY CYCLE]
[90%]
:N/A
Fan configuration
mode setting
Select Screen
Select Item
+- Change Field
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
The onboard hardware monitor automatically detects the optional fan speed. If the
fan is not connected to the motherboard, the field shows N/A.
OPT_Fan1/2 Q-Fan Control [DUTY CYCLE]
Allows you to select the optional fan control mode. When this item is set to
[DUTY CYCLE], you can configure the Duty Cycle Mode item. If you set this
item to [Q-FAN], you are allowed to configure the TargetTemp Value item.
The Q-Fan detects the temperature of the fan connected to the OPT_FAN1/2
connector and adjusts the fan speed.
Configuraiton options: [DUTY CYCLE] [Q-FAN]
You need to connect the thermal sensor cables to the OPT_TEMP1/2
connectors to enable this function.
ASUS Blitz Extreme
4-33
Duty Cycle Mode [90%]
Allows you to set the fan duty cycle. When the OPT_Fan1/2 Q-Fan Control item is
set to [Q-FAN], this item does not appear.
Configuraiton options: [70%] [80%] [90%] [100%]
TargetTemp Value [32]
Allows you to set the temperature at which the optional fan starts up. When the
OPT_Fan1/2 Q-Fan Control item is set to [DUTY CYCLE], this item does not
appear. Configuration options: [16] [24] [32] [40] [48] [56] [64] [72]
Power Fan Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the power
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A.
VCORE Voltage, FSB Termination Voltage, North Bridge Voltage,
DRAM Voltage, DRAM Reference Voltage, South Bridge Voltage, PLL
Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output through
the onboard voltage regulators.
4-34
Chapter 4: BIOS setup
4.7
Boot menu
The Boot menu items allow you to change the system boot options. Select an item
then press <Enter> to display the sub-menu.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
Tools
Exit
Specifies the Boot
Device Priority
sequence.
Boot Device Priority
Boot Settings Configuration
Security
A virtual floppy disk
drive (Floppy Drive B:)
may appear when you set
the CD-ROM drive as the
first boot device.
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.7.1
Boot Device Priority
BIOS SETUP UTILITY
Boot
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[Hard Drive]
[ATAPI CD-ROM]
Specifies the boot
sequence from the
availabe devices.
A device enclosed
in parenthesis has
been disabled in
the corresponding
menu.
+-
F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
1st ~ xxth Boot Device [xxx Drive]
These items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number of
devices installed in the system. Configuration options: [xxx Drive] [Disabled]
ASUS Blitz Extreme
4-35
4.7.2
Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Quick Boot [Enabled]
Full Screen Logo
[Enabled]
AddOn ROM Display Mode
[Force BIOS]
Bootup Num-Lock
[On]
Wait for ‘F1’ if Error
[Enabled]
Hit ‘DEL’ Message Display[Enabled]
Interrupt 19 Capture
[Disabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items. Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo3™ feature.
AddOn ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run Setup”
during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
Configuration options: [Disabled] [Enabled]
4-36
Chapter 4: BIOS setup
4.7.3
Security
The Security menu items allow you to change the system security settings. Select
an item then press <Enter> to display the configuration options.
BIOS SETUP UTILITY
Boot
Security Settings
Supervisor Password
User Password
:Not Installed
:Not Installed
<Enter> to change
password.
<Enter> again to
disabled password.
Change Supervisor Password
Change User Password
Enter
F1
F10
ESC
Select Screen
Select Item
Change
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default Not Installed. After you set a
password, this item shows Installed.
To set a Supervisor Password:
1.
2.
Select the Change Supervisor Password item and press <Enter>.
From the password box, type a password composed of at least six letters
and/or numbers, then press <Enter>.
3. Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a user
password.
To clear the supervisor password, select the Change Supervisor Password then
press <Enter>. The message “Password Uninstalled” appears.
If you forget your BIOS password, you can clear it by erasing the CMOS Real
Time Clock (RTC) RAM. See section 2.6 Jumper for information on how to
erase the RTC RAM.
ASUS Blitz Extreme
4-37
After you have set a supervisor password, the other items appear to allow you to
change other security settings.
BIOS SETUP UTILITY
Boot
Security Settings
Supervisor Password
User Password
:Not Installed
:Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
<Enter> to change
password.
<Enter> again to
disabled password.
[Full Access]
[Setup]
Enter
F1
F10
ESC
Select Screen
Select Item
Change
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
User Access Level [Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
[No Access] prevents user access to the Setup utility.
[View Only] allows access but does not allow change to any field.
[Limited] allows changes only to selected fields, such as Date and Time.
[Full Access] allows viewing and changing all the fields in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on
top of the screen shows the default Not Installed. After you set a password, this
item shows Installed.
To set a User Password:
1.
2.
Select the Change User Password item and press <Enter>.
On the password box that appears, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3. Confirm the password when prompted.
The message “Password Installed” appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user password.
Clear User Password
Select this item to clear the user password.
4-38
Chapter 4: BIOS setup
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup
utility. When set to [Always], BIOS checks for user password both when accessing
Setup and booting the system. Configuration options: [Setup] [Always]
4.8
Tools menu
The Tools menu items allow you to configure options for special functions. Select
an item then press <Enter> to display the sub-menu.
Main
Extreme Tweaker
BIOS SETUP UTILITY
Advanced
Power
Boot
Tools
Exit
Press ENTER to run
the utility to select
and update BIOS.
This utility doesn't
support :
1.NTFS format
ASUS EZ Flash 2
ASUS O.C. Profile
Select Screen
Select Item
Change Field
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
+-
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
4.8.1
ASUS EZ Flash 2
Allows you to run ASUS EZ Flash 2. When you press <Enter>, a confirmation
message appears. Use the left/right arrow key to select between [Yes] or [No],
then press <Enter> to confirm your choice. Please see page 4-5, section 4.1.3 for
details.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.05
FLASH TYPE: SST 25VF016
Current ROM
BOARD: Blitz Extreme
VER: 0122
DATE: 05/07/07
PATH: A:\
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
A:
Note
ASUS Blitz Extreme
[Enter] Select or Load
[Tab] Switch
[B] Backup
[ESC] Exit
[Up/Down/Home/End] Move
4-39
4.8.2
ASUS O.C. Profile
This item allows you to store or load multiple BIOS settings.
BIOS SETUP UTILITY
Tools
O.C. PROFILE Configuration
O.C. Profile 1 Status
O.C. Profile 2 Status
Save to Profile 1
:Not Installed
:Not Installed
Save to Profile 1
Load from Profile 1
Save to Profile 2
Load from Profile 2
Start O.C. Profile
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Save to Profle 1/2
Allows you to save the current BIOS file to the BIOS Flash. Press <Enter> to save
the file.
Load from Profile 1/2
Allows you to load the previous BIOS settings saved in the BIOS Flash. Press
<Enter> to load the file.
Start O.C. Profile
Allows you to run the utility to save and load CMOS. Press <Enter> to run the
utility.
ASUSTek O.C. Profile Utility V1.05
Current CMOS
BOARD: Blitz Extreme
VER: 0122
DATE: 05/07/07
PATH: A:\
Restore CMOS
BOARD: Unknown
VER: Unknown
DATE: Unknown
A:
Note
[Enter] Select or Load
[Tab] Switch
•
•
4-40
[B] Backup
[ESC] Exit
[Up/Down/Home/End] Move
This function can support devices such as USB flash disk or floppy
disk with FAT 32/16 format and single partition only.
DO NOT shut down or reset the system while updating the BIOS to
prevent the system boot failure!
Chapter 4: BIOS setup
4.9
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values for the
BIOS items, and save or discard your changes to the BIOS items.
Main
Extreme Tweaker
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
BIOS SETUP UTILITY
Advanced
Power
Boot
Tools
Exit
Exit system setup
after saving the
changes.
F10 key can be used
for this operation.
Load Setup Defaults
Enter
Tab
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
Select Field
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
Pressing <Esc> does not immediately exit this menu. Select one of the options
from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are finished making your selections, choose this option from the Exit
menu to ensure the values you selected are saved to the CMOS RAM. An onboard
backup battery sustains the CMOS RAM so it stays on even when the PC is turned
off. When you select this option, a confirmation window appears. Select YES to
save changes and exit.
If you attempt to exit the Setup program without saving your changes, the
program prompts you with a message asking if you want to save your changes
before exiting. Press <Enter> to save the changes while exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you made to the
Setup program. If you made changes to fields other than System Date, System
Time, and Password, the BIOS asks for a confirmation before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation appears. Select
YES to discard any changes and load the previously saved values.
Load Setup Defaults
This option allows you to load the default values for each of the parameters on the
Setup menus. When you select this option or if you press <F5>, a confirmation
window appears. Select YES to load default values. Select Exit & Save Changes
or make other changes before saving the values to the non-volatile RAM.
ASUS Blitz Extreme
4-41
4-42
Chapter 4: BIOS setup
This chapter describes the contents of
the support DVD that comes with the
motherboard package and the softwares.
5
Software
support
Chapter summary
5.1
5.2
5.3
5.4
5.5
5
Installing an operating system.................................................... 5-1
Support DVD information............................................................. 5-1
Software information.................................................................... 5-9
RAID configurations................................................................... 5-30
Creating a RAID driver disk........................................................ 5-47
ASUS Blitz Extreme
5.1
Installing an operating system
This motherboard supports Windows® XP/ 64-bit XP/ Vista™ operating systems
(OS). Always install the latest OS version and corresponding updates to maximize
the features of your hardware.
5.2
•
Motherboard settings and hardware options vary. Use the setup
procedures presented in this chapter for reference only. Refer to your OS
documentation for detailed information.
•
Make sure that you install the Windows® XP Service Pack2 or later versions
before installing the drivers for better compatibility and system stability.
Support DVD information
The support DVD that came with the motherboard package contains the drivers,
software applications, and utilities that you can install to avail all motherboard
features.
The contents of the support DVD are subject to change at any time without
notice. Visit the ASUS website(www.asus.com) for updates.
5.2.1
Running the support DVD
Place the support DVD to the optical drive. The DVD automatically displays the
Drivers menu if Autorun is enabled in your computer.
Click an icon to
display support DVD/
motherboard information
Click an item to install
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the DVD.
ASUS Blitz Extreme
5-
5.2.2
Drivers menu
The Drivers menu shows the available device drivers if the system detects installed
devices. Install the necessary drivers to activate the devices.
ASUS InstAll - Installation Wizard for Drivers
Installs all of the drivers through the Installation Wizard.
Intel(R) Chipset Inf Update Program
Installs the Intel® chipset Inf update program.
SoundMAX ADI1988 Audio Driver
Installs the SoundMAX® ADI1988 audio driver and application.
Marvell Yukon Gigabit Ethernet Driver
Installs the Marvell Yukon Gigabit Ethernet driver.
USB 2.0 Driver
Installs the USB 2.0 driver.
5-
Chapter 5: Software support
5.2.3
Utilities menu
The Utilities menu shows the applications and other software that the motherboard
supports.
Click to display
the next page
ASUS InstAll - Installation Wizard for Utilities
Click to return
to the previous
page
Installs all of the utilities through the Installation Wizard.
Marvell Yukon VCT Application
Installs the Marvell® Yukon Virtual Cable Tester™ (VCT) application that diagnoses
and reports LAN cable faults and shorts using the Time Domain Reflectometry
(TDR) technology.
ASUS PC Probe II
This smart utility monitors the fan speed, CPU temperature, and system voltages,
and alerts you of any detected problems. This utility helps you keep your computer
in healthy operating condition.
ASUS Blitz Extreme
5-
ASUS AI Suite
Installs the ASUS AI Suite.
ASUS Update
The ASUS Update utility allows you to update the motherboard BIOS in
Windows® environment. This utility requires an Internet connection either
through a network or an Internet Service Provider (ISP).
ADOBE Acrobat Reader V7.0
Installs the Adobe® Acrobat® Reader that allows you to open, view, and print
documents in Portable Document Format (PDF).
Microsoft DirectX 9.0c
Installs the Microsoft® DirectX 9.0c driver. The Microsoft DirectX® 9.0c is a
multimedia technology that enhances computer graphics and sound. DirectX®
improves the multimedia features of you computer so you can enjoy watching
TV and movies, capturing videos, or playing games in your computer. Visit
the Microsoft website (www.microsoft.com) for updates.
Anti-Virus Utility
The anti-virus application scans, identifies, and removes computer viruses.
View the online help for detailed information.
3DMark06 Software
Installs the 3DMark software.
WinDVD Copy5 Trial
Installs the WinDVD Copy5 trial version.
InterVideo MediaOne Gallery
Installs the media library and all-in-one software.
Ulead PhotoImpact 12 SE
Installs the PhotoImpact image editing software.
CyberLink PowerBackup
Installs CyberLink PowerBackup to back up and restore your data easily.
Corel Snapfire Plus SE
Installs Corel Snapfire Plus SE.
5-
Chapter 5: Software support
5.2.4
Make disk menu
The Make disk menu contains items to create the Intel ICH9 or JMicron® JMB36X
RAID/AHCI driver disk.
Make Intel ICH9R 32/64bit AHCI/RAID Driver Disk
Allows you to create an ICH9R 32/64bit AHCI/RAID driver disk.
Make JMicron JMB36X 32/64bit SATA/RAID Driver
Allows you to create a JMicron® JMB36X 32/64bit SATA/RAID driver.
ASUS Blitz Extreme
5-
5.2.5
Manual menu
The Manual menu contains a list of supplementary user manuals. Click an item to
open the folder of the user manual.
Most user manual files are in Portable Document Format (PDF). Install the Adobe®
Acrobat® Reader from the Utilities menu before opening a user manual file.
5.2.6
ASUS Contact information
Click the Contact tab to display the ASUS contact information. You can also find
this information on the inside front cover of this user guide.
5-
Chapter 5: Software support
5.2.7
Other information
The icons on the top right corner of the screen give additional information on the
motherboard and the contents of the support DVD. Click an icon to display the
specified information.
Motherboard Info
Displays the general specifications of the motherboard.
Browse this DVD
Displays the support DVD contents in graphical format.
ASUS Blitz Extreme
5-
Technical support Form
Displays the ASUS Technical Support Request Form that you have to fill out when
requesting technical support.
Filelist
Displays the contents of the support DVD in text format.
5-
Chapter 5: Software support
5.3
Software information
Most of the applications in the support DVD have wizards that will conveniently
guide you through the installation. View the online help or readme file that came
with the software application for more information.
5.3.1
ASUS MyLogo3™
The ASUS MyLogo3™ utility lets you customize the boot logo. The boot logo is the
image that appears on screen during the Power‑On‑Self-Tests (POST). The ASUS
MyLogo3™ is automatically installed when you install the ASUS Update utility from
the support DVD. See section 5.2.3 Utilities menu for details.
•
Before using the ASUS MyLogo3™, use the AFUDOS utility to make a copy
of your original BIOS file, or obtain the latest BIOS version from the ASUS
website. See section 4.1.4 AFUDOS utility.
•
Make sure that the BIOS item Full Screen Logo is set to [Enabled] if
you wish to use ASUS MyLogo3. See section 4.7.2 Boot Settings
Configuration.
•
You can create your own boot logo image in GIF, JPG, or BMP file formats.
To launch the ASUS MyLogo3™:
1.
2.
3.
4.
5.
6.
Launch the ASUS Update utility. Refer to section 4.1.1 ASUS Update utility
for details.
Select Options from the drop down menu, then click Next.
Check the option Launch MyLogo to replace system boot logo before
flashing BIOS, then click Next.
Select Update BIOS from a file from the drop down menu, then click Next.
When prompted, locate the new BIOS file, then click Next. The ASUS
MyLogo3 window appears.
From the left window pane, select
the folder that contains the image
you intend to use as your boot logo.
ASUS Blitz Extreme
5-
7.
When the logo images appear on the
right window pane, select an image to
enlarge by clicking on it.
8.
Adjust the boot image to your desired
size by selecting a value on the Ratio
box.
9.
When the screen returns to the ASUS Update utility, flash the original BIOS to
load the new boot logo.
10. After flashing the BIOS, restart the computer to display the new boot logo
during POST.
5-10
Chapter 5: Software support
5.3.2
AI NET2
The AI NET2 features the Marvell® Virtual Cable Tester™ (VCT). VCT is a cable
diagnostic utility that reports LAN cable faults and shorts using the Time Domain
Reflectometry (TDR) technology. The VCT detects and reports open and shorted
cables, impedance mismatches, pair swaps, pair polarity problems, and pair skew
problems of up to 64 ns at one meter accuracy.
The VCT feature reduces networking and support costs through a highly
manageable and controlled network system. This utility can be incorporated
in the network systems sofware for ideal field support as well as development
diagnostics.
Using the Virtual Cable Tester™
To use the the Marvell® Virtual Cable Tester™ utility:
1.
Launch the VCT utility from the Windows® desktop by clicking Start > All
Programs > Marvell > Virtual Cable Tester.
2. Click Virtual Cable Tester from the menu to display the screen below.
3.
Click the Run button to perform a cable test.
•
The VCT utility only tests Ethernet cables connected to Gigabit LAN port(s).
•
If you want the system to check the status of the LAN cable before entering
the OS, enable the item Post Check LAN Cable in the BIOS Setup.
•
The Run button on the Virtual Cable Tester™ main window is disabled if no
problem is detected on the LAN cable(s) connected to the LAN port(s).
ASUS Blitz Extreme
5-11
5.3.3
ASUS PC Probe II
PC Probe II is a utility that monitors the computer’s vital components, and detects
and alerts you of any problem with these components. PC Probe II senses fan
rotations, CPU temperature, and system voltages, among others. Because PC
Probe II is software-based, you can start monitoring your computer the moment
you turn it on. With this utility, you are assured that your computer is always at a
healthy operating condition.
Installing PC Probe II
To install PC Probe II on your computer:
1.
Place the support DVD to the optical drive. The Drivers installation tab
appears if your computer has an enabled Autorun feature.
If Autorun is not enabled in your computer, browse the contents of the support
DVD to locate the setup.exe file from the ASUS PC Probe II folder. Double-click
the setup.exe file to start installation.
2.
3.
Click the Utilities tab, then click ASUS PC Probe II.
Follow the screen instructions to complete installation.
Launching PC Probe II
You can launch the PC Probe II right after installation or anytime from the
Windows® desktop.
To launch the PC Probe II from the Windows® desktop, click Start > All Programs
> ASUS > PC Probe II > PC Probe II v1.xx.xx. The PC Probe II main window
appears.
After launching the application, the PC Probe II icon appears in the Windows®
taskbar. Click this icon to close or restore the application.
Using PC Probe II
Main window
The PC Probe II main window allows you to view the current status of your
system and change the utility
configuration. By default, the main
window displays the Preference
section. You can close or restore
the Preference section by clicking
on the triangle on the main
window right handle.
Click to close the
Preference panel
5-12
Chapter 5: Software support
Button
Function
Opens the Configuration window
Opens the Desktop Management Interface window
Opens the Report window
Opens the Peripheral Component Interconnect window
Opens the Windows Management Instrumentation window
Opens the hard disk drive, memory, CPU usage window
Shows/Hides the Preference section
Minimizes the application
Closes the application
Sensor alert
When a system sensor detects a problem, the main window right handle
turns red, as the illustrations below show.
When displayed, the monitor panel for that sensor also turns red. Refer to the
Monitor panels section for details.
Preferences
You can customize the application using the
Preference section in the main window. Click
the box before each preference to activate or
deactivate.
ASUS Blitz Extreme
5-13
Hardware monitor panels
The hardware monitor panels display the current value of a system sensor such as
fan rotation, CPU temperature, and voltages.
The hardware monitor panels come in two display modes: hexagonal (large) and
rectangular (small). When you check the Enable Monitoring Panel option from the
Preference section, the monitor panels appear on your computer’s desktop.
Small display
Large display
Changing the monitor panels position
To change the position of the monitor panels in the desktop,
click the arrow down button of the Scheme options, then select
another position from the list box. Click OK when finished.
Moving the monitor panels
All monitor panels move together using a magnetic effect. If
you want to detach a monitor panel from
the group, click the horseshoe magnet
icon. You can now move or reposition the
panel independently.
Adjusting the sensor threshold value
You can adjust the sensor threshold
value in the monitor panel by
clicking the or buttons. You can
also adjust the threshold values
using the Config window.
You cannot adjust the sensor
threshold values in a small
monitoring panel.
5-14
Click to
increase
value
Click to
decrease
value
Chapter 5: Software support
Monitoring sensor alert
The monitor panel turns red when a component value exceeds or is lower
than the threshold value. Refer to the illustrations below.
Small display
Large display
WMI browser
Click
to display the
WMI (Windows Management
Instrumentation) browser. This
browser displays various Windows®
management information. Click an
item from the left panel to display on
the right panel. Click the plus sign (+)
before WMI Information to display the
available information.
You can enlarge or reduce the browser size by dragging the bottom right corner
of the browser.
DMI browser
Click
to display the DMI
(Desktop Management Interface)
browser. This browser displays various
desktop and system information.
Click the plus sign (+) before DMI
Information to display the available
information.
ASUS Blitz Extreme
5-15
PCI browser
Click
to display the PCI
(Peripheral Component Interconnect)
browser. This browser provides
information on the PCI devices installed
on your system. Click the plus sign
(+) before the PCI Information item to
display available information.
Usage
The Usage browser displays real-time information on the CPU, hard disk drive
space, and memory usage. Click
to display the Usage browser.
CPU usage
The CPU tab displays realtime CPU usage in line graph
representation. If the CPU has
an enabled Hyper­‑Threading,
two separate line graphs display
the operation of the two logical
processors.
Hard disk drive space usage
The Hard Disk tab displays the
used and available hard disk
drive space. The left panel of the
tab lists all logical drives. Click
a hard disk drive to display the
information on the right panel.
The pie chart at the bottom of the
window represents the used (blue)
and the available HDD space.
5-16
Chapter 5: Software support
Memory usage
The Memory tab shows both
used and available physical
memory. The pie chart at the
bottom of the window represents
the used (blue) and the available
physical memory.
Configuring PC Probe II
Click
to view and adjust the sensor threshold values.
The Config window has two tabs: Sensor/Threshold and Preference. The Sensor/
Threshold tab enables you to activate the sensors or to adjust the sensor threshold
values. The Preference tab allows you to customize sensor alerts, or change the
temperature scale.
Loads the default
threshold values for
each sensor
ASUS Blitz Extreme
Applies your
changes
Cancels or
ignores your
changes
Loads your saved
configuration
Saves your
configuration
5-17
5.3.4 ASUS AI Suite
ASUS AI Suite allows you to launch AI Gear 2, AI N.O.S., AI Booster, AI Nap, and
Q-Fan Plus utilities easily.
Installing AI Suite
To install AI Suite on your computer:
1.
2.
3.
Place the support DVD to the optical drive. The Drivers installation tab
appears if your computer has an enabled Autorun feature.
Click the Utilities tab, then click AI Suite.
Follow the screen instructions to complete installation.
Launching AI Suite
You can launch the AI Suite right after installation or anytime from the Windows®
desktop.
To launch the AI Suite from the Windows® desktop, click Start > All Programs >
ASUS > AI Suite > AI Suite v1.xx.xx. The AI Suite main window appears.
After launching the application, the AI Suite icon appears in the Windows® taskbar.
Click this icon to close or restore the application.
Using AI Suite
Click the AI N.O.S., AI Gear 2, AI Nap, AI Booster, or Q-Fan Plus icon to launch the
utility, or click the Normal icon to restore the system to normal state.
Press to restore to normal
Press to launch AI Nap
5-18
Press to launch AI Gear 2
Press to launch AI N.O.S.
Press to launch AI Booster
Press to launch Q-Fan Plus
Chapter 5: Software support
Other feature buttons
Click
on right corner of the main window to open the monitor window.
Displays the CPU/
system temperature,
CPU/memory/PCIE
voltage, and CPU/
chassis fan speed
Displays the FSB/CPU
frequency
Click
on right corner of the expanded window to switch the temperature from
degrees Centigrade to degrees Fahrenheit.
ASUS Blitz Extreme
5-19
5.3.5 ASUS AI Gear 2
ASUS AI Gear 2 provides four system performance options that allows you to
select the best performance setting for your computing needs. This easy-to-use
utility adjusts the processor frequency and vCore voltage to minimize system noise
and power consumption.
After installing AI Suite from the bundled support DVD, you can launch AI Gear 2
by double-clicking the AI Suite icon on your Windows OS taskbar and then click the
AI Gear 2 button on the AI Suite main window.
Shift the gear to the performance setting that you like.
Maximum
Performance
Medium
Performance
High
Performance
5-20
Maximum
Power Saving
Chapter 5: Software support
5.3.6
ASUS AI Nap
This feature allows you to minimize the power consumption of your computer
whenever you are away. Enable this feature for minimum power consumption and
a more quiet system operation.
After installing AI Suite from the bundled support DVD, you can launch the utility by
double-clicking the AI Suite icon on the Windows OS taskbar and click the AI Nap
button on the AI Suite main window.
Click Yes on the confirmation screen.
To exit AI Nap mode, press the system power or mouse button then click Yes on
the confirmation screen.
To switch the power button functions from AI Nap to shutting down, just right
click the AI Suite icon on the OS taskbar, select AI Nap and click Use power
button. Unclick the the item to switch the function back.
ASUS Blitz Extreme
5-21
5.3.7
ASUS AI N.O.S.
This ASUS Non-delay Overclocking System feature intelligently determines the
system load and automatically boosts the performance for the most demanding
tasks.
After installing AI Suite from the bundled support DVD, you can launch the utility
by double-clicking the AI Suite icon on the Windows OS taskbar and click the AI
N.O.S. button on the AI Suite main window.
drop-down
menu button
Click the drop-down menu button and select Disable or Manual.
select an
N.O.S. mode
Click Apply at the bottom to save the configuration.
5-22
Chapter 5: Software support
5.3.8
ASUS Q-Fan Plus
This ASUS Q-Fan Plus Control feature allows you to set the appropriate
performance level of the CPU Q-Fan or the Chassis Q-Fan for more efficient
system operation. After enabling the Q-Fan Plus function, the fans can be set to
automatically adjust depending on the temperature, to decrease fan speed, or to
achieve the maximum fan speed.
After installing AI Suite from the bundled support DVD, you can launch the utility by
double-clicking the AI Suite icon on the Windows® OS taskbar and click the Q-Fan
Plus button on the AI Suite main window.
Click the drop-down menu button
and display the fan names. Select
CPU Q-Fan or CHASSIS Q-Fan.
Click the box of Enable Q-Fan to
activate this function.
drop-down list button
Enable Q-Fan box
Profile list appears after clicking
the Enable Q-Fan box. Click
the drop-down list button and
select a profile. Optimal mode
makes the fans adjust speed with
the temperature; Silent mode
minimizes fan speed for quiet fan
operation; Performance mode
boosts the fan to achieve maximal
fan speed for the best cooling
effect.
click to display the
drop-down list and
select a Q-Fan mode
Click Apply at the bottom to save the setup.
ASUS Blitz Extreme
5-23
5.3.9
ASUS AI Booster
The ASUS AI Booster application allows you to overclock the CPU speed in
WIndows® environment without the hassle of booting the BIOS.
After installing AI Suite from the bundled support DVD, you can launch the utility
by double-clicking the AI Suite icon on the Windows® OS taskbar and click the AI
Booster button on the AI Suite main window.
The options on the taskbar allow you to use the default settings, adjust CPU/
Memory/PCI-E frequency manually, or create and apply your personal overclocking
configurations.
5-24
Chapter 5: Software support
5.3.10
SoundMAX® High Definition Audio utility
The ADI AD1988 High Definition Audio CODEC provides 8-channel audio capability
through the SoundMAX® audio utility with AudioESP™ software to deliver the
ultimate audio experience on your PC. The software implements high quality audio
synthesis/rendering, 3D sound positioning, and advanced voice-input technologies.
Follow the installation wizard to install the ADI AD1988 Audio Driver from the
support CD that came with the motherboard package to activate the SoundMAX®
audio utility.
You must use 4-channel, 6-channel or 8-channel speakers for this setup.
If the SoundMAX® audio utility is correctly installed, you
will find the SoundMAX® icon on the taskbar.
ASUS Blitz Extreme
5-25
From the taskbar, double-click on the SoundMAX® icon to display the SoundMAX®
Control Panel.
Audio Setup Wizard
By clicking the
icon from the SoundMAX® control panel, you can easily
configure your audio settings. Simply follow succeeding screen instructions and
begin enjoying High Definition Audio.
5-26
Chapter 5: Software support
Jack configuration
This screen helps you configure your
computer’s audio ports, depending on
the audio devices you have installed.
Adjust speaker volume
This screen helps you adjust speaker
volume. Click the Test button to hear
the changes you have made.
Adjust microphone volume
This screen helps you adjust microphone volume. You will be asked to read prewritten text to allow the AudioWizard to adjust the volume as you speak.
ASUS Blitz Extreme
5-27
Audio preferences
Click the
icon to go to the Preferences page. This page allows you to change
various audio settings.
General options
Click the General tab to choose your playback and recording devices, enable/
disable the AudioESP™ feature, and enable/disable digital output.
Listening Environment options
Click the Listening Environment tab to set up your speaker, acoustic environment,
and enable/disable the Virtual Theater Surround function.
5-28
Chapter 5: Software support
Microphone options
Click the Microphone tab allows you to optimize your microphone input settings.
Enhanced Microphone Features
Voice recording
Enables Noise Filter function. Detects repetitive and stationary noises like
computer fans, air conditioners, and other background noises then eliminates
it in the incoming sudio stream while recording. You can enable it for a better
recording quality.
Directional Array
Receives only the sound coming from the reception cone and eliminates
interferences including neighboring speakers and reverberations. You can
enable it to transit clearer sound during on-line games, MSN, or Skype.
Speaker Phone
Advanced de-reverberation techniques can help to reduce echo and minimize
its effect on the speech engine. You can enable it when you have conference
call to reduce echoes in the other side.
•
The directional Array and Speaker Phone
function only when working with the ASUS
Array Mic.
•
If you are using Windows Vista, you have to
manually enable the directional Array and
Speaker Phone function. Go to Control
panel > Sound. Click the Recording tab on
the top and select Microphone. Click the
Microphone Enhancement tab and check
Array Mic.
ASUS Blitz Extreme
5-29
5.4
RAID configurations
The motherboard comes with the Intel® ICH9R Southbridge RAID controller that
allow you to configure IDE and Serial ATA hard disk drives as RAID sets. The
motherboard supports the following RAID configurations.
5.4.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write
data in parallel, interleaved stacks. Two hard disks perform the same work as a
single drive but at a sustained data transfer rate, double that of a single disk alone,
thus improving data access and storage. Use of two new identical hard disk drives
is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one
drive to a second drive. If one drive fails, the disk array management software
directs all applications to the surviving drive as it contains a complete copy of
the data in the other drive. This RAID configuration provides data protection and
increases fault tolerance to the entire system. Use two new drives or use an
existing drive and a new drive for this setup. The new drive must be of the same
size or larger than the existing drive.
RAID 10 is data striping and data mirroring combined without parity (redundancy
data) having to be calculated and written. With the RAID 10 configuration you get
all the benefits of both RAID 0 and RAID 1 configurations. Use four new hard disk
drives or use an existing drive and three new drives for this setup.
RAID 5 stripes both data and parity information across three or more hard
disk drives. Among the advantages of RAID 5 configuration include better
HDD performance, fault tolerance, and higher storage capacity. The RAID
5 configuration is best suited for transaction processing, relational database
applications, enterprise resource planning, and other business systems. Use a
minimum of three identical hard disk drives for this setup.
Intel® Matrix Storage. The Intel® Matrix Storage technology supported by the
ICH9R chip allows you to create a RAID 0, RAID 1, RAID 5, and RAID 10 function
to improve both system performance and data safety. You can also combine two
RAID sets to get higher performance, capacity, or fault tolerance provided by the
difference RAID function. For example, RAID 0 and RAID 1 set can be created by
using only two identical hard disk drives.
If you want to boot the system from a hard disk drive included in a created RAID
set, copy first the RAID driver from the support CD to a floppy disk before you
install an operating system to the selected hard disk drive. Refer to section 5.6
Creating a RAID driver disk for details.
5-30
Chapter 5: Software support
5.4.2
Installing Serial ATA hard disks
The motherboard supports Serial ATA hard disk drives. For optimal performance,
install identical drives of the same model and capacity when creating a disk array.
To install the SATA hard disks for a RAID configuration:
1.
Install the SATA hard disks into the drive bays.
3.
Connect a SATA power cable to the power connector on each drive.
2.
Connect the SATA signal cables.
5.4.3
Intel® RAID configurations
This motherboard supports RAID 0, RAID 1, RAID 5, RAID 10 (0+1) and Intel®
Matrix Storage configurations for Serial ATA hard disks drives through the Intel®
ICH9R Southbridge chip.
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID
set(s). To do this:
1.
Enter the BIOS Setup during POST.
3.
Select the item Configure SATA As, then press <Enter> to display the
configuration options.
2.
4.
5.
6.
Go to the Main Menu, select SATA Configuration, then press <Enter>.
Select [RAID] from the Configure SATA As item options, then press <Enter>.
Select the item Onboard Serial-ATA BOOTROM, press <Enter>, then select
[Enabled] from the options.
Save your changes, then exit the BIOS Setup.
Refer to the system or the motherboard user guide for details on entering and
navigating through the BIOS Setup.
ASUS Blitz Extreme
5-31
Intel® Matrix Storage Manager Option ROM Utility
The Intel® Matrix Storage Manager Option ROM utility allows you to create RAID 0,
RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial ATA hard disk drives
that are connected to the Serial ATA connectors supported by the Southbridge.
To enter the Intel® Application Accelerator RAID Option ROM utility:
1.
Install all the Serial ATA hard disk drives.
3.
During POST, press <Ctrl+I> to display the utility main menu.
2.
Turn on the system.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
None defined.
Physical Disks:
Port Drive Model
0
XXXXXXXXXXX
1
XXXXXXXXXXX
2
XXXXXXXXXXX
3
XXXXXXXXXXX
[↑↓]-Select
Serial #
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
[ESC]-Exit
Size
Type/Status(Vol ID)
XX.XXGB Non-RAID Disk
XX.XXGB Non-RAID Disk
XX.XXGB Non-RAID Disk
XX.XXGB Non-RAID Disk
[ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through
the menus and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and
may not exactly match the items on your screen.
5-32
Chapter 5: Software support
Creating a RAID 0 set (striped)
To create a RAID 0 set:
1.
From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume0
RAID0(Stripe)
Select Disks
128KB
0.0
GB
Create Volume
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
[↑↓]-Change
2.
3.
4.
[TAB]-Next
[ESC]-Previous Menu
[Enter]-Select
Enter a name for the RAID 0 set, then press <Enter>.
When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 0(Stripe), then press <Enter>.
When the Disks item is highlighted, press <Enter> to select the hard disk
drives to configure as RAID. This pop‑up screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
Serial #
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
Size
XX.XGB
XX.XGB
XX.XGB
XX.XGB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 2 to 4 disks to use in creating the volume.
[↑↓]-Previous/Next
5.
[SPACE]-Selects
[ENTER]-Selection Complete
Use the up/down arrow key to highlight a drive, then press <Space> to
select. A small triangle marks the selected drive. Press <Enter> after
completing your selection.
ASUS Blitz Extreme
5-33
6.
Use the up/down arrow key to select the stripe size for the RAID 0 array, then
press <Enter>. The available stripe size values range from 4 KB to 128 KB.
The default stripe size is 128 KB.
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
7.
8.
Key in the RAID volume capacity that you want, then press <Enter>. The
default value indicates the maximum allowed capacity.
Press <Enter> when the Create Volume item is highlighted. This warning
message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
9.
5-34
Press <Y> to create the RAID volume and return to the main menu, or <N> to
go back to the Create Volume menu.
Chapter 5: Software support
Creating a RAID 1 set (mirrored)
To create a RAID 1 set:
1.
From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume1
RAID1(Mirror)
Select Disks
N/A
XX.X GB
Create Volume
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
[↑↓]-Change
2.
3.
4.
5.
[TAB]-Next
[ESC]-Previous Menu
[Enter]-Select
Enter a name for the RAID 1 set, then press <Enter>.
When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 1(Mirror), then press <Enter>.
When the Capacity item is highlighted, key in the RAID volume capacity that
you want, then press <Enter>. The default value indicates the maximum
allowed capacity.
Press <Enter> when the Create Volume item is highlighted. This warning
message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
6.
Press <Y> to create the RAID volume and return to main menu or <N> to go
back to Create Volume menu.
ASUS Blitz Extreme
5-35
Creating a RAID 10 set (RAID 0+1)
To create a RAID 10 set:
1.
From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume10
RAID10(RAID0+1)
Select Disks
128KB
XXX.X GB
Create Volume
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
[↑↓]-Change
2.
3.
4.
[TAB]-Next
[ESC]-Previous Menu
[Enter]-Select
Enter a name for the RAID 10 set, then press <Enter>.
When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 10(RAID0+1), then press <Enter>.
When the Stripe Size item is highlighted, press the up/down arrow key to
select the stripe size for the RAID 10 array, then press <Enter>. The available
stripe size values range from 4 KB to 128 KB. The default stripe size is 64
KB.
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
5.
5-36
Key in the RAID volume capacity that you want then press <Enter> when
the Capacity item is highlighted. The default value indicates the maximum
allowed capacity.
Chapter 5: Software support
6.
Press <Enter> when the Create Volume item is highlighted. This warning
message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
7.
Press <Y> to create the RAID volume and return to the main menu or <N> to
go back to the Create Volume menu.
Creating a RAID 5 set (parity)
To create a RAID 5 set:
1.
From the utility main menu, select 1. Create RAID Volume, then press
<Enter>. This screen appears.
Intel(R) Matrix Storage Manager Option ROM v5.0.0.1032 ICH9R wRAID5
Copyright(C) 2003-05 Intel Corporation. All Rights Reserved.
[ CREATE ARRAY MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Volume5
RAID5(Parity)
Select Disks
64KB
0.0 GB
Create Volume
[ DISK/VOLUME INFORMATION ]
Enter a string between 1 and 16 characters in length that can be used
to uniquely identify the RAID volume. This name is case sensitive and
cannot contain special characters.
[↑↓]-Change
2.
3.
[TAB]-Next
[ESC]-Previous Menu
[Enter]-Select
Enter a name for the RAID 5 set, then press <Enter>.
When the RAID Level item is highlighted, press the up/down arrow key to
select RAID 5(Parity), then press <Enter>.
ASUS Blitz Extreme
5-37
4.
The Disks item is highlighted, press <Enter> to select the hard disk drives to
configure as RAID. The following pop‑up screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
XXXXXXXXXXXX
Serial #
XXXXXXXX
XXXXXXXX
XXXXXXXX
XXXXXXXX
Size
XX.XGB
XX.XGB
XX.XGB
XX.XGB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 2 to 4 disks to use in creating the volume.
[↑↓]-Previous/Next
5.
6.
[SPACE]-Selects
[ENTER]-Selection Complete
Use the up/down arrow key to highlight the drive you want to set, then press
<Space> to select. A small triangle marks the selected drive. Press <Enter>
after completing your selection.
When the Stripe Size item is highlighted, press the up/down arrow key
to select the stripe size for the RAID 5 array, then press <Enter>. The available stripe size values range from 4 KB to 128 KB. The default stripe
size is 64 KB.
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
7.
8.
Key in the RAID volume capacity that you want, then press <Enter> when
the Capacity item is highlighted. The default value indicates the maximum
allowed capacity.
Press <Enter> when the Create Volume item is highlighted. This warning
message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
9.
5-38
Press <Y> to create the RAID volume and return to the main menu or <N> to
go back to the Create Volume menu.
Chapter 5: Software support
5.4.4
JMicron® RAID Configuration
The JMicron® Serial ATA controller allows you to configure RAID 0, RAID 1 and
JBOD sets on the external Serial ATA hard disk drives.
Before creating a RAID set
Prepare the following items:
1.
2.
3.
4.
Two SATA HDDs, preferably with the same model and capacity.
A write-enabled floppy disk (Windows XP). A write-enabled floppy disk or a
USB flash disk drive (Windows Vista)
Microsoft® Windows® OS installation disk (Windows XP)
Motherboard support DVD with JMB363 driver
Complete the following steps before you create a RAID set:
1.
2.
Install two external Serial ATA hard disk drives on your system.
Set the Controller Mode item in the BIOS to [RAID]. See section 4.5.5
Onboard Devices Configuration for details.
BIOS SETUP UTILITY
Advanced
Onboard Device Configuration
J-Micron eSATA/PATA Controller
Controller Mode
Marvell Gigabit LAN 1
LAN Boot ROM
Marvell Gigabit LAN 2
LAN Boot ROM
VIA Firewire 1394
Options
[Enabled]
[IDE]
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Enabled]
Enabled
Disabled
Select Screen
Select Item
+- Change Option
F1 General Help
F10 Save and Exit
ESC Exit
v02.58 (C)Copyright 1985-2007, American Megatrends, Inc.
3.
4.
5.
Enter the JMB363 RAID BIOS utility to set up your RAID configuration.
Create a JMB363 RAID driver disk for Windows® OS installation. See section
5.5 Creating a RAID driver disk for details.
Install the JMB363 driver after the Windows® OS had been installed.
Always install the JMB363 driver before creating RAID sets.
ASUS Blitz Extreme
5-39
Entering the JMB363 RAID BIOS utility
1. During POST, press <Ctrl-J> to enter the JBM363 RAID BIOS menu.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.97
Copyright (C) 2004-2005 JMicron Technology
http://www. jmicron.com
HDD0 : HDS722516VLSA80 HDD1 : HDS722516DLA380
164 GB Non-RAID
164 GB Non-RAID
Press <Ctrl-J> to enter RAID Setup Utility...
2.
3.
The main JMB363 RAID BIOS menu appears.
Use the arrow keys to move the color bar and navigate through the items.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.97
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
[Hard Disk Drive List]
Model Name
Capacity Type/Status
HDD0:HDS722516VLSA80 164 GB
Non-RAID
HDD1:HDS722516DLA380 164 GB Non-RAID
[RAID Disk Drive List]
[
TAB]-Switch Window [↑↓]-Select Item
[ENTER]-Action
[ESC]-Exit
Creating a RAID set
1. In the main JMB363 RAID BIOS menu, highlight Create RAID Disk Drive
using the up/down arrow key then press <Enter>.
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
5-40
Chapter 5: Software support
2. When the Level item is highlighted, use the up/down arrow key to select the
RAID set that you want to create.
[Create New RAID]
Name : JRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128 KB
Size : 319 GB
Confirm Creation
[Create New RAID]
Name : JRAID
Level: 1-Mirror
Disks: Select Disk
Block: N/A
Size : 159 GB
Confirm Creation
3. When the Disks item is highlighted, use the up/down arrow key to highlight
an HDD that you want to belong to the RAID set, then press the space bar to
confirm selection. Repeat the process until the HDDs are selected.
A selected HDD shows a
sign before it.
[Hard Disk Drive List]
Model Name
HDD0: HDS722516VLSA80 HDD1: HDS722516DLA380
Capacity
XXX GB XXX GB Type/Status
Non-RAID
Non-RAID
4. Key in the RAID volume capacity. Use the up/down arrow to choose the block
size. The default value indicates the maximum allowed capacity.
[Create New RAID]
Name : JRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128 KB
Size : 319 GB
Confirm Creation
ASUS Blitz Extreme
5-41
5. When done, press <Enter> to confirm the creation of the RAID set. A dialogue
box appears to confirm the action. Press <Y> to confirm; otherwise, press
<N>.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller BIOS v0.97
[Create New RAID]
Name: JRAID
Level: 0-Stripe
Disks: Select Disk
Block: 128 KB
Size : 319 GB
Confirm Creation
[Hard Disk Drive List]
Model Name
Available
HDD0: HDS722516VLSA80 164 GB
HDD1: HDS722516DLA380 164 GB Type/Status
Non-RAID
Non-RAID
[RAID Disk Drive List]
Create RAID on the selected HDD (Y/N)? Y
CONFIRM RAID CREATION
ALL DATA ON THE SELECTED HARD DISK
WILL BE LOST WHEN EXIT WITH SAVING
[
TAB]-Switch Window [↑↓]-Select Item
[ENTER]-Action
[ESC]-Exit
Pressing <Y> deletes all the data in the HDDs.
6. The following screen appears, displaying the relevant information about the
RAID set you created.
[RAID Disk Drive List]
Model Name RAID Level Capacity Status Members(HDDx)
RDD0:JRAID
0-Stripe XXX GB
Normal 01
5-42
Chapter 5: Software support
Deleting a RAID set
1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive
using the up/down arrow key then press <Enter>.
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
2. Use the space bar to select the RAID set you want to delete.
3.
A selected set shows a
set.
sign before it. Press the <Del> key to delete the
A dialogue box appears to confirm the action. Press <Y> to confirm;
otherwise, press <N>.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller
[Main Menu]
[Hard Disk Drive List]
Create RAID Disk Drive
Model Name
Capacity
Delete RAID Disk Drive
HDD0: HDS722516VLSA80 164 GB
Revert HDD to Non-RAID
HDD1: HDS722516DLA380 164 GB Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
[RAID Disk Drive
ALLList]
DATA ON THE RAID WILL BE LOST!!
ModelARE
NameYOU RAID
Capacity
Status
SURELevel
TO DELETE
(Y/N)?
Y
Members(HDDx)
RDD0: JRAID
0-Stripe
XXX GB
Normal
[
TAB]-Switch Window [↑↓]-Select Item
[ENTER]-Action
BIOS v0.97
Type/Status
RAID Inside
RAID Inside
01
[ESC]-Exit
Pressing <Y> deletes all the data in the HDDs.
ASUS Blitz Extreme
5-43
Resetting disks to non-RAID
•
An HDD that has been previously configured as part of another RAID set in
another platform is called a broken RAID HDD. When you install a broken
RAID HDD, you cannot select this HDD when configuring a RAID set
through the JMB363 utility.
•
If you still want to use this broken RAID HDD as part of the RAID set
configured through the JMB363, you may do so by resetting the disk to nonRAID. You will, however, lose all data and previous RAID configurations.
To reset disks to non-RAID:
1. In the main JMB363 RAID BIOS menu, highlight Revert HDD to non‑RAID
using the up/down arrow key then press <Enter>.
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
2. Use the space bar to select the HDD that you want to reset to non‑RAID.
3.
A selected HDD shows a
sign before it.
A dialogue box appears to confirm the action. Press <Y> to confirm;
otherwise, press <N>.
Pressing <Y> deletes all the data in the HDD.
5-44
Chapter 5: Software support
Solving a Mirror conflict
A Mirror conflict occurs when both disks in a RAID 1 (Mirror) configuration are
unplugged from the system in turn, then plugged in again. Since both disks contain
exactly the same data, the system will be unable to determine which of the two
is the source drive. This option allows you to set the source drive and rebuild the
Mirror drive according to the contents of the source drive.
To solve a Mirror conflict:
1. In the main JMB363 RAID BIOS menu, highlight Solve Mirror Conflict using
the up/down arrow key then press <Enter>.
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
2. Use the space bar to select the HDD that you want to set as source drive.
sign before it.
The selected HDD shows a
A status bar at the bottom of the screen shows the progress of the rebuilding.
3.
Using the <TAB>, move to the RAID Disk Drive List menu and highlight the
RAID set that you want to rebuild. Press <Del> to begin rebuilding the Mirror
configuration.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller
[Main Menu]
[Hard Disk Drive List]
Create RAID Disk Drive
Model Name
Capacity
Delete RAID Disk Drive
HDD0: HDS722516VLSA80 164 GB
Revert HDD to Non-RAID
HDD1: HDS722516DLA380 164 GB Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
[RAID Disk Drive List]
Model Name
Members(HDDx)
RDD0: JRAID
RAID Level Capacity
Status
1-Mirror
XXX GB
Rebuild
BIOS v0.97
Type/Status
RAID Inside
RAID Inside
01
Rebuilding... 01%, please wait...
ASUS Blitz Extreme
5-45
Rebuilding a Mirror Drive
When one of the disks in a RAID 1 (Mirror) configuration is unplugged from the
system, then plugged in again, a dialogue box appears to ask you to rebuild the
Mirror drive. Press <Y> to confirm; otherwise, press <N>.
This option allows you to rebuild the Mirror drive later and synchronize the data
between two hard disks.
To rebuild a Mirror drive:
1. In the main JMB363 RAID BIOS menu, highlight Rebuild Mirror Drive using
the up/down arrow key then press <Enter>.
[Main Menu]
Create RAID Disk Drive
Delete RAID Disk Drive
Revert HDD to Non-RAID
Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
2.
Using the <TAB>, move to the RAID Disk Drive List menu and highlight the
RAID set that you want to rebuild. Press <Del> to begin rebuilding the Mirror
configuration.
A status bar at the bottom of the screen shows the progress of the rebuilding.
JMicron Technology Corp. PCI-to-SATA II/IDE RAID Controller
[Main Menu]
[Hard Disk Drive List]
Create RAID Disk Drive
Model Name
Capacity
Delete RAID Disk Drive
HDD0: HDS722516VLSA80 164 GB
Revert HDD to Non-RAID
HDD1: HDS722516DLA380 164 GB Solve Mirror Conflict
Rebuild Mirror Drive
Save and Exit Setup
Exit Without Saving
[RAID Disk Drive List]
Model Name
Members(HDDx)
RDD0: JRAID
RAID Level Capacity
Status
1-Mirror
XXX GB
Rebuild
BIOS v0.97
Type/Status
RAID Inside
RAID Inside
01
Rebuilding... 01%, please wait...
Saving the settings and exiting setup
When you have finished, highlight Save & Exit Setup using the up/down arrow key
then press <Enter> to save the current RAID configuration and exit the JMB363
RAID BOS utility.
A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise,
press <N> to return to the JMB RAID BIOS menu.
5-46
Chapter 5: Software support
5.5
Creating a RAID driver disk
A floppy disk with the RAID driver is required when installing Windows® XP/Vista
and later operating system on a hard disk drive that is included in a RAID set. For
Windows Vista user, you can create a RAID driver disk with a floppy disk drive or a
USB flash disk drive.
5.5.1
Creating a RAID driver disk without entering the OS
To create a RAID driver disk without entering the OS:
1. Boot your computer.
2.
Press <Del> during POST to enter the BIOS setup utility.
4.
Insert the support CD into the optical drive.
3.
5.
6.
7.
8.
9.
Set the optical drive as the primary boot device.
Save changes and exit BIOS.
Press any key when the system prompts “Press any key to boot from the
optical drive.”
When the menu appears, press <1> to create a RAID driver disk.
Insert a formatted floppy disk into the floppy drive then press <Enter>.
Follow succeeding screen instructions to complete the process.
5.5.2
Creating a RAID driver disk in Windows®
To create a RAID driver disk in Windows®:
1.
Start Windows®.
3.
Go to the Make Disk menu, then click Intel ICH9R 32/64 bit RAID Driver
Disk to create an Intel® ICH9R RAID driver disk or the Make JMicron
JMB36X 32/64-bit RAID Driver to create a JMicron JMB363 RAID driver
disk.
2.
4.
5.
Place the motherboard support CD into the optical drive.
Insert a floppy disk into the floppy disk drive or connect a USB flash disk if
you are using Windows Vista OS.
Follow succeeding screen instructions to complete the process.
Write-protect the floppy disk to avoid computer virus infection.
ASUS Blitz Extreme
5-47
To install the RAID driver in Windows XP:
1.
2.
3.
4.
During the OS installation, the system prompts you to press the <F6> key to
install third-party SCSI or RAID driver.
Press <F6> then insert the floppy disk with RAID driver into the floppy disk
drive.
When prompted to select the SCSI adapter to install, make sure you select
Intel(R) SATA RAID Controller (Desktop ICH9R) and JMicron JMB363.
Follow the succeeding screen instructions to complete the installation.
To install the RAID driver in Windows® Vista:
1. Insert the floppy disk/USB device with RAID driver into the floppy disk drive/USB
port.
2. During the OS installation, select JMicron JMB363.
3. Follow the succeeding screen instructions to complete the installation.
5-48
Chapter 5: Software support
This chapter tells how to install ATI®
CrossFire™ graphics cards to avail of
ATI’s Multi-Video Processing technology.
6
ATI® CrossFire™
technology support
Chapter summary
6
6.1
Overview........................................................................................ 6-1
6.3
Software information.................................................................... 6-5
6.2
Installing CrossFire™ graphics cards........................................ 6-2
ASUS Blitz Extreme
6.1
Overview
The motherboard supports the ATI® CrossFire™ technology that allows you to
install multi-graphics processing units (GPU) graphics cards. Follow the installation
procedures in this section.
6.1.1
Requirements
•
CrossFire™ Edition graphics card (Master)
•
CrossFire™-ready motherboard
•
•
CrossFire™-ready graphics card (Slave)
Make sure that your power supply unit (PSU) can provide at least the
minimum power required by your system. See 9. ATX Power connectors on
page 2-30 for details.
6.1.2
•
Visit the ATI website or download the Radeon® X850 Crossfire™ Edition
User’s Guide from the support CD for detailed hardware requirements and
installation procedures.
•
The ATI CrossFire™ technology supports only the following operating
systems:
- Windows® XP 32-bit (Home or Professional) with Service
Pack 2 (SP2)
- Windows® XP Professional 64-bit Edition.
•
Make sure that your graphics card driver supports the ATI® CrossFire™
Technology. Download the latest driver from the ATI website (www.ati.com)
•
The maximum resolution of Radeon™ X850 CrossFire™ Edition is 1600 x
1200 at 65 MHz when you use DVI output.
Before you begin
Uninstall other graphics card drivers in your system
To uninstall other graphics card drivers:
1.
Close all current applications.
3.
Select your current graphics card driver/s.
5.
Restart your system.
2.
4.
Go to Control Panel > Add/Remove Programs.
Select Add/Remove.
ASUS Blitz Extreme
6-
6.2
Installing CrossFire™ graphics cards
Before installing a CrossFire™ system, refer to the user guide that came with
the ATI® CrossFire™ Edition graphics card.
To install the graphics cards:
1.
Prepare one CrossFire™ Edition (Master) graphics card and one
CrossFire™-ready (Slave) graphics card.
Slave graphics card
Master graphics card
2. Insert the CrossFire™ Edition (Master) graphics card into the PCI Express
x16 blue slot. Make sure that the card is properly seated on the slot.
6-
Chapter 6: ATI® MVP technology support
3. Insert the CrossFire™-ready (Slave) graphics card into the PCI Express x16
blue slot. Make sure that the card is properly seated on the slot.
4. Connect an auxiliary power source from the power supply to the graphics
cards.
ASUS Blitz Extreme
6-
5. Connect one end of the external cable to the Master graphics card.
6. Connect the other end of the external cable to the Slave graphics card.
7.
Connect the loose end to the corresponding port on your monitor.
6
7
6-
Chapter 6: ATI® MVP technology support
6.3
Software information
6.3.1
Installing the device drivers
Refer to the documentation that came with your graphics card package to install
the device drivers.
The ATI CrossFire™ technology supports only the following operating systems:
• Windows® XP 32-bit (Home or Professional) with Service
Pack 2 (SP2)
• Windows® XP Professional 64-bit Edition.
• Windows® Vista 32/64 bit Edition. (Will be ready later. Visit the ATI
website (www.ati.com)
1.
2.
3.
Turn on your system and log in
with administrator rights.
Windows® auto-detects the
CrossFire™ graphics cards
and displays the Found New
Hardware Wizard window. Click
Cancel.
Place the CrossFire™ installation
CD in your optical drive and install
drivers from the opening menu.
4.
Click Next to continue from the
installation window that appears.
5.
Read the License Agreement,
then click Yes.
ASUS Blitz Extreme
6-
6.
•
Select Express to install the HydraVision™ multi-monitor and desktop
management software, as well as the ATI driver.
•
Select Custom to individually choose desired software components.
Setup prepares the installation
wizard that will guide you to setup
process.
Windows automatically configures
the ATI Catalyst Control Center.
The status windows indicates the
progress of the installation.
7.
The Setup Complete window
appears, indicating that the driver
files have been copied to your
computer.
8.
6-
Select the components that you
want to install, then click Next.
Click Yes to restart your computer
now or No to restart later
Click Finish.
Chapter 6: ATI® MVP technology support
6.3.2
Using the Catalyst™ Control Center
The Catalyst™ Control Center allows you to access display features of the ATI
hardware and software you installed. Use this application to adjust your graphic
settings, enable/disable connected devices, and change your desktop orientation.
Launching the Catalyst™ Control Center
There are several ways to launch the Catalyst™ Control Center:
• On the Windows® task bar, click Start > ATI Catalyst™ Control Center >
Catalyst™ Control Center
• Double-click the Catalyst™ Control Center desktop shortcut.
• On the Windows® task bar, doubleclick the Catalyst™ Control Center
icon.
ASUS Blitz Extreme
6-
The Catalyst™ Control Center Dialog Box
View
The Catalyst™ Control Center provides two views:
Standard - simple view with wizards for beginners
Advance - allows advanced users to access and configure the complete
features of the software
Set to Advance view to enable the CrossFire™ function.
6-
Chapter 6: ATI® MVP technology support
To enable CrossFire™:
1. Set the view to Advance.
2. Click the Crossfire™ item in Graphics Settings.
3. In the CrossFire™ Settings dialog, tick the box opposite Enable
CrossFire™.
4. Click OK to effect the setting.
3
2
4
Hotkeys
Click the Hotkeys tab on the Catalyst™ Control Center to access the Hotkeys
Manager, which allows you to create key combinations as shortcuts for
performing certain functions quickly.
ASUS Blitz Extreme
6-
Profiles
Click the Profiles tab on the Catalyst™ Control Center to access the Profiles
Manager, which allows you to create customized environments for your
desktop, video, and 3D applications.
Preferences
Click the Preferences tab on the Catalyst™ Control Center to select a
language, restore defaults, change skins, or enable/disable the System Tray
icon.
6-10
Chapter 6: ATI® MVP technology support
Help
Click the Help tab on the Catalyst™ Control Center to access the online help
system, generate a Problem Report, and get the Catalyst™ Control Center
version information.
ASUS Blitz Extreme
6-11
6-12
Chapter 6: ATI® MVP technology support
The Appendix describes the CPU features
and technologies that the motherboard
supports as well as the debug code table
for the LCD Poster.
A
CPU features
Chapter summary
A
A.1
Intel EM64T...................................................................................A-1
A.3
Intel® Hyper-Threading Technology............................................A-3
A.2
A.4
®
Enhanced Intel SpeedStep® Technology (EIST).........................A-1
Debug Code Table.........................................................................A-4
ASUS Blitz Extreme
A.1
Intel® EM64T
•
The motherboard is fully compatible with Intel® LGA775 processors running
on 32-bit operating systems.
•
The motherboard comes with a BIOS file that supports EM64T. You can
download the latest BIOS file from the ASUS website (www.asus.com/
support/download/) if you need to update the BIOS file. See Chapter 4 for
details.
•
Visit www.intel.com for more information on the EM64T feature.
•
Visit www.microsoft.com for more information on Windows® 64-bit OS.
Using the Intel® EM64T feature
To use the Intel® EM64T feature:
1.
2.
3.
4.
Install an Intel® CPU that supports the Intel® EM64T.
Install a 64-bit operating system (Windows® Vista 64-bit Edition, Windows® XP
Professional x64 Edition or Windows® Server 2003 x64 Edition).
Install the 64-bit drivers for the motherboard components and devices from
the support DVD.
Install the 64-bit drivers for expansion cards or add-on devices, if any.
Refer to the expansion card or add-on device(s) documentation, or visit the
related website, to verify if the card/device supports a 64-bit system.
A.2
A.2.1
Enhanced Intel SpeedStep®
Technology (EIST)
•
The motherboard comes with a BIOS file that supports EIST. You can
download the latest BIOS file from the ASUS website (www.asus.com/
support/download/) if you need to update the BIOS. See Chapter 4 for
details.
•
Visit www.intel.com for more information on the EIST feature.
System requirements
Before using EIST, check your system if it meets the following requirements:
•
Intel® processor with EIST support
•
Operating system with EIST support (Windows® Vista, Windows® XP SP2/
Windows® Server 2003 SP1/Linux 2.6 kernel or later versions)
•
BIOS file with EIST support
ASUS Blitz Extreme
A-
A.2.2
Using the EIST
To use the EIST feature:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Turn on the computer, then enter the BIOS Setup.
Go to the Advanced Menu, highlight CPU Configuration,
then press <Enter>.
Set the Intel(R) SpeedStep Technology item to [Automatic],
then press <Enter>.
Press <F10> to save your changes and exit the BIOS setup.
After the computer restarts, right click on a blank space on the desktop, then
select Properties from the pop-up menu.
When the Display Properties
window appears, click the Screen
Saver tab.
Click the Power button on the
Monitor power section to open the
Power Options Properties window.
On the Power schemes section,
click , then select any option
except Home/Office Desktop or
Always On.
Click Apply, then click OK.
10. Close the Display Properties
window.
After you adjust the power scheme,
the CPU internal frequency slightly
decreases when the CPU loading is
low.
The screen displays and procedures may vary depending on the operating
system.
A-
Appendix: CPU features
A.3
Intel® Hyper-Threading Technology
•
The motherboard supports Intel® Pentium® 4 LGA775 processors with
Hyper-Threading Technology.
•
Hyper-Threading Technology is supported under Windows® Vista/XP/2003
Server and Linux 2.4.x (kernel) and later versions only. Under Linux, use
the Hyper-Threading compiler to compile the code. If you are using any
other operating systems, disable the Hyper-Threading Technology item in
the BIOS to ensure system stability and performance.
•
Installing Windows® XP Service Pack 1 or later version is recommended.
•
Make sure to enable the Hyper-Threading Technology item in BIOS before
installing a supported operating system.
•
For more information on Hyper-Threading Technology, visit www.intel.
com/info/hyperthreading.
Using the Hyper-Threading Technology
To use the Hyper-Threading Technology:
1.
2.
3.
Install an Intel® Pentium® 4 CPU that supports Hyper-Threading Technology.
Power up the system and enter the BIOS Setup. Under the Advanced Menu,
make sure that the item Hyper‑Threading Technology is set to [Enabled].
The BIOS item appears only if you installed a CPU that supports Hyper­
‑Threading Technology.
Restart the computer.
ASUS Blitz Extreme
A-
A.4
Debug Code Table
Code
CPU INIT
DET CPU
CHIPINIT
DET DRAM
DC FCODE
EFSHADOW
INIT IO
INIT HWM
CLR SCRN
INIT8042
ENABLEKB
DIS MS
R/W FSEG
DET FLASH
TESTCMOS
PRG CHIP
INIT CLK
CHECKCPU
INTRINIT
INITINT9
CPUSPEED
VGA BIOS
TESTVRAM
RESET KB
A-
Description
CPU Initiation
Test CMOS R/W functionality.
Early chipset initialization:
-Disable shadow RAM
-Disable L2 cache
-Program basic chipset registers
Detect memory
-Auto-detection of DRAM size, type and ECC.
-Auto-detection of L2 cache
Expand compressed BIOS code to DRAM
Call chipset hook to copy BIOS back to E000 & F000 shadow RAM.
Initialize IO devices.
Initialize Hardware Monitor.
1. Blank out screen
2. Clear CMOS error flag
1. Clear 8042 interface
2. Initialize 8042 self-test
1. Test special keyboard controller for Super I/O chips.
2. Enable keyboard interface.
1. Disable PS/2 mouse interface (optional).
2. Auto detect ports for keyboard & mouse followed by a port & interface
swap (optional).
3. Reset keyboard for Super I/O chips.
Test F000h segment shadow to see whether it is R/W-able or not. If test
fails, keep beeping the speaker.
Auto detect flash type to load appropriate flash R/W codes into the run time
area in F000 for ESCD & DMI support.
Use walking 1’s algorithm to check out interface in CMOS circuitry. Also set
real-time clock power status, and then check for override.
Program chipset default values into chipset.
Initialize clock generator.
Detect CPU information including brand, type and CPU level (586 or 686).
Initial interrupts vector table.
Initialize INT 09 buffer
1. Program CPU internal MTRR (Pentium class CPU) for 0-640K memory
address.
2. Initialize the APIC for Pentium class CPU.
3. Program early chipset according to CMOS setup. Example: onboard IDE
controller.
4. Measure CPU speed.
5. Invoke video BIOS.
Initialize VGA BIOS
1. Initialize multi-language
2. Put information on screen display, including BIOS logo, CPU type, CPU
speed .
Reset keyboard.
Appendix: CPU features
8254TEST
8259MSK1
8259MSK2
8259TEST
COUNTMEM
MP INIT
USB INIT
TEST MEM
SHOW MP
PNP LOGO
ONBD IO
EN SETUP
MSINSTAL
CHK ACPI
EN CACHE
SET CHIP
AUTO CFG
INIT FDC
DET IDE
COM/LPT
DET FPU
CPU CHG
EZ FLASH
CPR FAIL
FAN FAIL
UCODEERR
FLOPYERR
KB ERROR
HD ERR
CMOS ERR
MS ERROR
SMARTERR
HM ERROR
AINETERR
CASEOPEN
PASSWORD
ASUS Blitz Extreme
Test 8254
Test 8259 interrupt mask bits for channel 1.
Test 8259 interrupt mask bits for channel 2.
Test 8259 functionality.
Calculate total memory by testing the last double word of each 64K page.
1. Program MTRR of M1 CPU
2. Initialize L2 cache for P6 class CPU & program CPU with proper
cacheable range.
3. Initialize the APIC for P6 class CPU.
4. On MP platform, adjust the cacheable range to smaller one in case the
cacheable ranges between each CPU are not identical.
Initialize USB
Test all memory (clear all extended memory to 0)
Display number of processors (multi-processor platform)
Display PnP logo
Initialize Onboard IO devices.
Okay to enter Setup utility.
Initialize PS/2 Mouse
Prepare memory size information for function call: INT 15h ax=E820h
Turn on L2 cache
Program chipset registers according to items described in Setup & Autoconfiguration table.
Assign resources to devices.
1. Initialize floppy controller
2. Set up floppy related fields in 40:hardware.
Detect & install all IDE devices: HDD, LS120, ZIP, CDROM.
Detect serial ports & parallel ports.
Detect & install co-processor
New CPU installed
Execute EZ Flash
CPR error
Fan error
UCODE error
Floppy error
Keyboard error
HDD error
CMOS error
Mouse error
HDD smart function error
Hard monitor error
AI NET error
Case open
Clear EPA or customization logo.
1. Call chipset power management hook.
2. Recover the text fond used by EPA logo (not for full screen logo)
3. If password is set, ask for password.
A-
USB FINAL
INIT ROM
NUM LOCK
UPDT DMI
INT 19H
A-
Initialize PnP boot devices
1. USB final Initialization
2. NET PC: Build SYSID structure
3. Switch screen back to text mode
4. Set up ACPI table at top of memory.
5. Invoke ISA adapter ROMs
6. Assign IRQs to PCI devices
7. Initialize APM
8. Clear noise of IRQs.
Initialize device option ROMs.
1. Program daylight saving
2. Update keyboard LED & typematic rate
1. Build MP table
2. Build & update ESCD
3. Set CMOS century to 20h or 19h
4. Load CMOS time into DOS timer tick
5. Build MSIRQ routing table.
Boot attempt (INT 19h)
Appendix: CPU features