6753i IP Phone
User Guide
Release 2.5
41-001199-21
Rev 00
Aastra Telecom will not accept liability for any damages and/or long distance charges, which result from unauthorized and/or
unlawful use. While every effort has been made to ensure accuracy, Aastra Telecom will not be liable for technical or editorial errors
or omissions contained within this documentation. The information contained in this documentation is subject to change without
notice.
Copyright 2008 Aastra Telecom. www.aastratelecom.com
All Rights Reserved.
Software License Agreement
Aastra Telecom Inc., hereinafter known as "Seller", grants to Customer a personal,
worldwide, non-transferable, non-sublicenseable and non-exclusive, restricted use license
to use Software in object form solely with the Equipment for which the Software was
intended. This Product may integrate programs, licensed to Aastra by third party
Suppliers, for distribution under the terms of this agreement. These programs are
confidential and proprietary, and are protected as such by copyright law as unpublished
works and by international treaties to the fullest extent under the applicable law of the
jurisdiction of the Customer. In addition, these confidential and proprietary programs are
works conforming to the requirements of Section 401 of title 17 of the United States Code.
Customer shall not disclose to any third party such confidential and proprietary programs
and information and shall not export licensed Software to any country except in
accordance with United States Export laws and restrictions.
Customer's use of this software shall be deemed to reflect Customer's agreement to abide
by the terms and conditions contained herein. Removal or modification of trademarks,
copyright notices, logos, etc., or the use of Software on any Equipment other than that for
which it is intended, or any other material breach of this Agreement, shall automatically
terminate this license. If this Agreement is terminated for breach, Customer shall
immediately discontinue use and destroy or return to Seller all licensed software and other
confidential or proprietary information of Seller. In no event shall Seller or its suppliers or
licensors be liable for any damages whatsoever (including without limitation, damages for
loss of business profits, business interruption, loss of business information, other
pecuniary loss, or consequential damages) arising out of the use of or inability to use the
software, even if Seller has been advised of the possibility of such damages.
iii
Software License Agreement
Customer agrees to not reverse engineer, decompile, disassemble or display Software
furnished in object code form. Customer shall not modify, copy, reproduce, distribute,
transcribe, translate or reduce to electronic medium or machine readable form or
language, derive source code without the express written consent of the Seller and its
Suppliers, or disseminate or otherwise disclose the Software to third parties. All Software
furnished hereunder (whether or not part of firmware), including all copies thereof, are
and shall remain the property of Seller and its Suppliers and are subject to the terms and
conditions of this agreement. All rights reserved.
Table of Contents
Table of Contents
Software License Agreement ...................................................................................................... iii
Table of Contents ..........................................................................................................................v
About This Guide ..........................................................................................................................1
Documentation ..........................................................................................................................1
Introduction ...................................................................................................................................2
Phone Features ..........................................................................................................................2
Requirements ............................................................................................................................2
Installation and Setup ................................................................................................................3
Getting Started ..............................................................................................................................4
Plugging in and Starting the Phone ...........................................................................................4
Idle Screens ...............................................................................................................................7
Incomplete Configuration .........................................................................................................8
No Service .................................................................................................................................8
IP Phone Keys and Key Descriptions ..........................................................................................9
Key Panel ..................................................................................................................................9
Methods for Customizing Your Phone ......................................................................................11
Phone Options via the IP Phone UI ........................................................................................11
Phone Options via the Aastra Web UI ....................................................................................14
Phone Status ................................................................................................................................18
Phone Status via IP Phone UI .................................................................................................18
Finding Your Phone’s IP Address ..........................................................................................19
Phone Status via the Aastra Web UI .......................................................................................19
Customizing Your Phone ............................................................................................................23
Ring Tones and Tone Sets .......................................................................................................23
Contrast Level .........................................................................................................................26
Live Dialpad* .........................................................................................................................26
Set Audio ................................................................................................................................27
Time and Date .........................................................................................................................28
Language .................................................................................................................................32
User Password .........................................................................................................................41
Resetting a User Password ......................................................................................................42
Restarting Your Phone ............................................................................................................43
Phone Lock .............................................................................................................................44
Defining an Emergency Dial Plan ..........................................................................................45
v
Table of Contents
Table of Contents
Line Keys and Programmable Keys ..........................................................................................47
Multiple Line and Call Appearance Keys ...............................................................................47
Programmable Keys ................................................................................................................48
Line Key .................................................................................................................................51
Creating a Speeddial Key .......................................................................................................52
Editing Speeddial Keys ...........................................................................................................58
Do Not Disturb (DND) Key ....................................................................................................62
Busy Lamp Field (BLF) Key ..................................................................................................63
BLF List Key ..........................................................................................................................65
Flash Key ................................................................................................................................68
Automatic Call Distribution (ACD) Key (for Sylantro Servers) ............................................69
Directed Call Pickup/Group Call Pickup Keys (for Sylantro Servers) ...................................73
XML Key ................................................................................................................................77
Sprecode Key ..........................................................................................................................80
Park/Pickup Keys ....................................................................................................................81
Last Call Return (lcr) Key (for Sylantro Servers) ...................................................................84
Call Forward Key ....................................................................................................................85
BLF/Xfer .................................................................................................................................86
Speeddial/Xfer ........................................................................................................................88
Speeddial/Conf ........................................................................................................................90
Directory Key .........................................................................................................................92
Callers List Key ......................................................................................................................94
Transfer Key ...........................................................................................................................96
Conference Key ......................................................................................................................98
Intercom Key ........................................................................................................................100
Services Key .........................................................................................................................102
Phone Lock Key ....................................................................................................................104
Paging Key (Sends the RTP Stream) ....................................................................................106
None Key ..............................................................................................................................108
Deleting a Key .....................................................................................................................109
Making Calls .............................................................................................................................110
Dialing a Number ..................................................................................................................110
Using Handsfree Speakerphone ............................................................................................110
Using a Headset .................................................................................................................... 111
vi
Table of Contents
Table of Contents
Redial ....................................................................................................................................112
Mute ......................................................................................................................................113
Receiving Calls ..........................................................................................................................114
Answering an Incoming Call ................................................................................................114
Sending an Incoming Call to Voicemail ...............................................................................114
Handling Calls ...........................................................................................................................115
Placing a Call on Hold ..........................................................................................................115
Transferring Calls .................................................................................................................116
Conferencing Calls ...............................................................................................................118
Ending Calls ..........................................................................................................................123
Managing Calls .........................................................................................................................124
Directory List ........................................................................................................................124
Callers List ............................................................................................................................134
Account Configuration (DND and Call Forwarding) ...........................................................140
Missed Calls Indicator ..........................................................................................................160
Voicemail ..............................................................................................................................161
Additional Features ..................................................................................................................162
Star Codes .............................................................................................................................162
Suppress DTMF Playback ....................................................................................................163
Display DTMF Digits ...........................................................................................................164
Enable/Disable Call Waiting .................................................................................................166
Play Call Waiting Tone .........................................................................................................168
Stuttered Dial Tone ...............................................................................................................169
XML Beep Support ...............................................................................................................170
Status Scroll Delay ................................................................................................................171
Incoming Call Interrupts Dialing ..........................................................................................172
Switch UI Focus to Ringing Line .........................................................................................174
Preferred Line and Preferred Line Timeout ..........................................................................175
Goodbye Key Cancels Incoming Calls .................................................................................177
UPnP Mapping Lines (for remote phones) ...........................................................................179
Message Waiting Indicator ...................................................................................................180
Incoming Intercom Call Features .........................................................................................181
Using Redial Key for “Last Number Redial” .......................................................................183
Group RTP Paging (receives RTP streams) ..........................................................................184
vii
Table of Contents
Table of Contents
Use LLDP ELIN ...................................................................................................................186
Shared Call Appearance (SCA) Call Bridging .....................................................................187
Available Features Enabled by Administrators .....................................................................190
Outgoing Intercom Calls .......................................................................................................190
Missed Call Summary Subscription .....................................................................................190
Customizable Callers List Key .............................................................................................191
Autodial (Hotline and Warmline) .........................................................................................191
Centralized Conferencing .....................................................................................................192
Answer and Ignore Keys for XML Applications ..................................................................192
Playing a WAV File On Your Phone .....................................................................................193
Using the Keypad During Active XML Applications ..........................................................193
Key Redirection ....................................................................................................................194
XML Applications and Off-Hook Interaction ......................................................................195
XML Override for a Locked Phone ......................................................................................195
RTP Recording and Simultaneous Playing ...........................................................................195
“Hold” Feature Enhancement (for Broadsoft Servers) .........................................................196
Configurable Save and Delete Keys .....................................................................................196
Authentication Support for HTTP/HTTPS Download Methods
Used with Broadsoft Client Management System (CMS) ....................................................196
Diverting Calls from Your Phone .........................................................................................198
Display of Call Destination Information ..............................................................................199
Model M670i Expansion Module .............................................................................................200
Using the Expansion Module ................................................................................................201
Troubleshooting Solutions ........................................................................................................202
Limited Warranty .....................................................................................................................207
Appendix A - Time Zone Codes .............................................................................................. A-1
Index ................................................................................................................................... Index-1
viii
About This Guide
This guide explains how to use your new 6753i phone. Not all features listed are available by
default. Contact your System Administrator to find out which features and services are available
on your system. Your System Administrator also has the ability to customize some features on this
phone.
Documentation
•
Aastra 6753i SIP IP Phone Installation Guide – Contains installation and set-up instructions,
general features and functions, and basic options list customization. This Installation Guide is
included in the box with your phone.
•
Aastra 6753i SIP IP Phone User Guide – Describes the most commonly used features and
functions for an end user. This User Guide can be downloaded from www.aastratelecom.com.
•
Aastra SIP IP Phone Administrator Guide –
Contains advanced Administrator information and procedures for setting up the 6753i IP
Phone on a network. This Administrator Guide is intended for the System Administrator and
can be downloaded from www.aastratelecom.com.
About This Guide
Model 6753i IP Phone User Guide
1
Introduction
Introduction
This 6753i IP telephone has all the features of a regular business phone, allowing you to make
and receive calls, transfer, conference and more. The 6753i IP telephone provides
communications over an IP Network using the SIP IP telephony protocol.
Phone Features
•
3-line LCD screen
•
6 top keys - all 6 keys are programmable
•
Press-and-hold speeddial key configuration feature
•
3 call appearance lines with LEDs
•
Supports up to 9 call lines
•
Full-duplex speakerphone for handsfree calls
•
Headset mode support (via handset jack)
•
Built-in two-port, 10/100 Ethernet ports - lets you share a connection with your computer
•
Inline power support (based on 802.3af standard) which eliminates power adapters
•
AC power adapter (included)
•
Enhanced busy lamp fields*
•
Set paging*
*Availability of feature dependant on your phone system or service provider.
Requirements
The 6753i IP Phone requires the following environment:
2
•
SIP-based IP PBX system or network installed and running with a SIP account created for
the 6753i IP phone.
•
Access to a Trivial File Transfer Protocol (TFTP), File Transfer Protocol (FTP), Hypertext
Transfer Protocol (HTTP) server, or HyperText Transfer Protocol over Secure Sockets Layer
(SSL) (HTTPS).
•
Ethernet/Fast Ethernet LAN (10/100 Mb)
•
Category 5/5e straight through cabling
Model 6753i IP Phone User Guide
•
Power source
— For Ethernet networks that supply in-line power to the phone (IEEE 802.3af):
— For power, use the Ethernet cable (supplied) to connect from the phone directly to the
network for power. (No 48v AC power adapter required.)
— For Ethernet networks that DO NOT supply power to the phone:
— For power, use the 48V AC Power Adapter (included) to connect from the DC power
port on the phone to a power source.
or
— (optional) - For power, use a Power over Ethernet (PoE) power injector or a PoE
switch. A PoE power injector is available as an optional accessory from Aastra
Telecom. Contact your Administrator for more information.
Installation and Setup
If your System Administrator has not already setup your 6753i phone, please refer to the Aastra
6753i Installation Guide for basic installation and physical setup of the 6753i. For more advanced
administration and configuration information, System Administrators should refer to the
Aastra SIP IP Phone Administrator Guide.
Introduction
Model 6753i IP Phone User Guide
3
Getting Started
Getting Started
The 6753i must be set up and configured prior to its first use. This section describes phone
behavior and start up screens you may see when the phone is first plugged in, or when it is
restarted.
Plugging in and Starting the Phone
The 6753i automatically begins the start up sequence as soon as it is connected. The phone goes
through this process the first time you plug in your phone and every time you restart your phone.
Note: Some start up screens only appear the first time you connect your phone,
or if your phone has been factory defaulted.
The phone displays the following startup screens.
Aastra 6753i
Firmware Loaded
LLDP
Initializing
network
During the first start up the 6753i phone attempts to contact the Redirection and Configuration
Server (rcs.aastra.com) for current server information. No personal information is transmitted
from the phone during this process.
Contacting
Redirector
4
Model 6753i IP Phone User Guide
The 6753i phone may also look for configuration servers on your local network (press 3Remote
to enter a remote server address, or 4Skip to continue without checking for servers).
Auto Discovery
Remote
Skip
If appropriate servers are found they are listed for you to select from by scrolling down to view the
complete list. (Press 3Skip to continue without selecting a server.).
Choose Server
<server name>
Skip
Select
The 6753i phone then checks settings and looks for new configuration and firmware updates for
the phone from a server. If a new update is found, the phone displays the message “Updating
Configuration”. This may take a few moments while the phone downloads the latest updates
Updating
configuration
.
Note: New updates to your phone can be automatically scheduled from the
server. This is set up on the phone system by your System Administrator and
should be scheduled during non-business hours or slow call periods.
Getting Started
Important! Do not unplug or remove power to the phone while it is checking or
installing firmware and configuration information.
If language packs were loaded to your phone by your System Administrator, the following
screen displays during startup.
Downloading
language packs.....
Model 6753i IP Phone User Guide
5
Getting Started
When the configuration update is complete, the phone displays the following screens.
Network
DSP
SIP
Done
6
Model 6753i IP Phone User Guide
Idle Screens
Idle Screen 1
When the phone has successfully updated the configuration and connected to the network, the
phone displays the Idle State screen:
1
John Burns
9054550055
Sat Jun 8 2:55pm
The Idle State screen lists your name (SIP screen name), extension (or phone number), and day,
date, and time. The "1" in the upper corner in the above example indicates the idle screen for the
first line appearance. You can use the left and right arrow keys to scroll through the idle screens for
all three line appearances. The 6753i allows for scrolling up to 3 lines.
This screen is shown whenever your phone is not in use.
Idle Screen 2
The second display line displays the following temporary messages if the event occurs:
•
No Service
•
DHCP Failed
•
Restarting......
•
New IP Obtained
•
Network Disconnected/Connected
Note: Since the "Network Disconnected/Connected" display on two lines, the
date and time does not show if this event displays.
The second line can also display the following status messages, listed in order of display priority:
Call forward status
•
DND On (Do Not Disturb)
•
Number of missed calls
Model 6753i IP Phone User Guide
Getting Started
•
7
Getting Started
When more than one status message displays, the 2 is shown after the message to indicate you
can use the 2 and 5 navigation keys to scroll through the remaining messages.
1
John Burns
CFWD All
Jun 8 2:55pm
2
Network Connected
Incomplete Configuration
If your phone displays an "Incomplete Config" message without any extension or user name at
the end of the start up sequence instead of an Idle state screen, this indicates the phone
configuration that was downloaded from the configuration server is not complete or correct.
Contact your System Administrator for assistance.
No Service
When the phone is not properly connected to the network, or the account has not been
configured by the Network Administrator, the "No Service" or "Network Disconnected" prompt
appears on the display and the telephone status light turns ON. The phone also displays the
default time and date of 12:00am Jan. 1st, 2000. Check that the cables are tightly connected to
the phone and to the wall jack. The phone should automatically detect when the connection is
reconnected and display the "Network Connected" prompt temporarily.
If changes have been made to your phone settings, you may need to restart your phone. For more
information on restarting your phone, see “Restarting Your Phone” on page 43.
For more information about connecting your phone, refer to the Aastra 6753i Installation Guide.
Check with your System Administrator for assistance.
8
Model 6753i IP Phone User Guide
IP Phone Keys and Key Descriptions
The following sections describe the various 6753i phone key functions, and how they help you
make and manage your calls and caller information.
IP Phone Keys and Key Descriptions
Key Panel
The following table identifies the keys on the key panel of your 6753i IP phone that you can use
for handling calls.
Keys
Key Description
Goodbye key - Ends an active call. The Goodbye key also exits an open
list, such as the Options List, without saving changes.
Options key - Accesses options to customize your phone. Your System
Administrator may have already customized some of your settings. Check
with your System Administrator before changing the Administrator-only
options.
Hold key - Places an active call on hold. To retrieve a held call, press the
call appearance button beside the light that is flashing.
Redial key - Redials up to 100 previously dialed numbers. Pressing the
Redial key twice simultaneously redials the last dialed number.53
Volume control key - Adjusts the volume for the handset, headset,
ringer, and handsfree speaker.
Model 6753i IP Phone User Guide
9
IP Phone Keys and Key Descriptions
Keys
Key Description
Line/Call Appearance key - Connects you to a line or call. The Aastra
6753i IP phone supports up to 3 line keys.
Handsfree key - Activates Handsfree for making and receiving calls
without lifting the handset. When the audio mode option is set, this key is
used to switch between a headset and the handsfree speakerphone.
Mute key - Mutes the microphone so that your caller cannot hear you (the
light indicator flashes when the microphone is on mute).
Navigation keys - Pressing the UP and DOWN arrow keys lets you view
different status and text messages on the LCD display (if there is more
than 1 line of status/text messages). These buttons also let you scroll
through menu selections, such as the Options List.
Pressing the LEFT and RIGHT arrow keys lets you view the different line/
call appearances. While in the Options List, these keys allow you to exit or
enter the current option. When you are editing entries on the display,
pressing the LEFT arrow key erases the character on the left; pressing
the RIGHT arrow key sets the option.
Programmable keys - 6 Top Keys - all 6 keys are programmable.
Keys 1 and 2 are designated as the SAVE and DELETE keys,
respectively. Only your System Administrator can make these keys
configurable, if required.
The following are the default functions for the programmable keys on the
6753i IP phone:
1
2
3
4
5
6
SAVE
Allows you to save numbers and/or names to the
Directory. Using this key, you enter the number,
name, and line (or speeddial key) to record in the
Directory List.
DELETE
Allows you to delete a single entry or all entries
from the Directory List and Callers List.
DIRECTORY
Displays up to 200 names and phone numbers
(stored in alphabetical order).
CALLERS LIST Accesses the last 200 calls received.
TRANSFER
Transfers the active call to another number.
CONFERENCE Begins a conference call with the active call.
Notes:
1. For more information about the SAVE and DELETE keys, see
“Configurable Save and Delete Keys” on page 196.
2. For more information about configuring keys 1 thru 6 to perform
specific functions, see “Programmable Keys” on page 48.
10
Model 6753i IP Phone User Guide
Methods for Customizing Your Phone
There are two ways to customize specific options on your phone:
•
Using the Options
key on the IP Phone
•
Using the Aastra Web UI in an Internet browser window from your PC.
Phone Options via the IP Phone UI
You can customize your phone by pressing the Options
key and accessing the IP Phone UI.
These options allow you to customize the following phone settings.
Option
Number
Methods for Customizing Your Phone
1
Option
Call Forward
1. Screenname
2. All Off
3. All On
Note: The menus that display for Call Forward
are dependant on the Call Forward Mode set on
the phone. Default is "Account" mode.
2
Services
1. Directory
2. Callers List
3. Voicemail
3
Preferences
1. Tones
Ring Tone
Tone Set
2. Contrast Level
3. Speeddial Edit
4. Live Dialpad
5. Set Audio
Audio Mode
Headset Mic Vol
6. Time and Date
Time Zone
Daylight Savings
Time Format
Date Format
Time Server
Time Server 1
Time Server 2
Time Server 3
Set Time
Set Date
7. Language
Screen Language
Input Language
Model 6753i IP Phone User Guide
11
Methods for Customizing Your Phone
4
Phone Status
1. IP&MAC Addresses
2. LAN Port
3. PC Port
4. Firmware Info
5. Error Messages
5
User Password
6
Administrator Menu
(Password Protected)
7
Restart Phone
8
Phone Lock
Note: *The "Administrator Menu" options are Administrator level functions
only, and are not accessible by the user. These options should only be set up and
changed by your System Administrator.
Simplified Options Menu
Your System Administrator may configure a simplified options menu for your phone. The
following table indicates the options that may appear on your phone if the simplified options
menu is applied.
Option
Number
1
Option
Call Forward
1. Screenname
2. All Off
3. All On
Note: The menus that display for Call Forward are
dependant on the Call Forward Mode set on the
phone. Default is "Account" mode.
12
2
Services
1. Directory
2. Callers List
3. Voicemail
2
Preferences
1. Tones
Ring Tone
Tone Set
2. Contrast Level
3. Live Dialpad
4. Set Audio
Audio Mode
Headset Mic Vol
3
Phone Status
1. IP&MAC Addresses
2. LAN Port
3. PC Port
4. Firmware Info
5. Error Messages
4
Phone Lock
Model 6753i IP Phone User Guide
Using the IP Phone UI
IP Phone UI
1. Press the Options key
on the phone to enter the Options List.
2. Use 2 and 5 to scroll through the list of options, or press the number corresponding to the
Option.
3. Press Enter, the 4 key, or press the digit number of the corresponding option to select an
option.
4. Change a selected option if applicable.
5. Press the Set or Done key to save the change.
6. Press the
changes.
button, the 3 key, or the
button at any time to exit without saving
For more information about customizing your phone using the available options from the IP Phone
UI, see the section “Customizing Your Phone” on page 23.
For more information about Administrator options, contact your System Administrator.
Model 6753i IP Phone User Guide
13
Methods for Customizing Your Phone
Reference
Methods for Customizing Your Phone
Phone Options via the Aastra Web UI
In addition to the IP Phone UI options, you can customize additional options on the IP Phone
using the Aastra Web UI. In order to access your phone using the Aastra Web UI, you need to
know your phone’s IP address. To find your phone’s IP address, see “Finding Your Phone’s IP
Address” on page 19.
Using the Aastra Web UI
Aastra Web UI
1. Open your web browser, enter the phone’s IP address or host name into the address field and
press <Enter>.
The following logon screen displays.
2. At the prompt, enter your username and password and click
Note: For a user, the default user name is “user” and the password field is left
blank.
14
Model 6753i IP Phone User Guide
The Network Status window displays for the IP phone you are accessing.
Methods for Customizing Your Phone
3. You can logout of the Aastra Web UI at any time by clicking Log Off.
Model 6753i IP Phone User Guide
15
Methods for Customizing Your Phone
The following categories display in the side menu of the Aastra Web UI: Status, Operation,
Basic Settings.
Headings
Descriptions
Status
The Status section displays the network status and the MAC address of the IP phone. It
also displays hardware and firmware information about the IP phone, and information about
the SIP account(s) currently configured on the phone. The information in the Network Status
window is read-only.
Operation
User Password - Allows you to change user password.
Phone Lock - Allows you to assign an emergency dial plan to the phone, lock the phone to
prevent any changes to the phone and to prevent use of the phone, and reset the user
password.
Keypad Speeddial - Allows you to assign a speeddial number to a specific digit on the
phone’s keypad for speeddialing purposes.
Programmable Keys - There are 6 function keys, all 6 of which you can configure to
perform the functions identified in the following list.
Your Administrator must unlock the SAVE and DELETE keys in order for these keys to be
configurable. For more information about the SAVE and DELETE keys, see “Configurable
Save and Delete Keys” on page 196.
•
none
•
Last Call Return (lcr)
•
line
•
Call Forward
•
speeddial
•
BLF/Xfer
•
do not disturb (DND)
•
Speeddial/Xfer
•
Busy Lamp Field
(BLF)
•
Speeddial/Conf
•
BLF List
•
Directory
•
Auto Call Distribution
(ACD)
•
Callers List
•
Directed Call Pickup
•
Conference
•
Extensible Markup
Language (XML)
•
Transfer
•
flash
•
Intercom
•
sprecode
•
Services
•
park
•
Phone Lock
•
pickup
•
Paging
Expansion Module - Allows you to configure an additional 36 keys with a M670i Expansion
Module if it is attached to the phone. This option displays on the side menu of the Aastra
Web UI only if an Expansion Module is attached.
Directory - Allows you to copy the Callers List and Directory List from your IP phone to your
PC.
Reset - Allows you to restart the IP phone when required.
16
Model 6753i IP Phone User Guide
Headings
Descriptions
Basic
Settings
Preferences - Allows you to enable/disable the following:
• Suppress DTMF Playback
• Display DTMF Digits
• Call Waiting
• Play Call Waiting Tone
• Stuttered Dial Tone
• XML Beep Support
• Status Scroll Delay (seconds)
• Incoming Call Interrupts Dialing
• Switch UI Focus to Ringing Line
• Preferred Line
• Preferred Line Timeout (seconds)
• Goodbye Key Cancels Incoming Call
• UPnP Mapping Lines
• Message Waiting Indicator Line
• DND Key Mode
• Call Forward Key Mode
• Use LLDP ELIN
Methods for Customizing Your Phone
This category also allows you to configure:
•
•
•
•
•
•
incoming Intercom call settings
group paging RTP settings
ring tones (global and per-line basis)
ring tone sets
time and date settings
Webpage language and input language
Account Configuration - Allows you to configure “do not disturb” (DND) and “call
forwarding” (CFWD) by account. You can have multiple accounts on the 6753i.
Model 6753i IP Phone User Guide
17
Phone Status
Phone Status
You can view the status of your phone using the IP Phone UI or the Aastra Web UI.
Phone Status via IP Phone UI
The "Phone Status" option on the IP phone displays the status of your phone to the LCD
display.
This option allows you to view your phone’s:
•
Network status including your phone’s IP and MAC address
•
Local Area Network (LAN) port information
•
PC Port information (if PC link exists)
•
Firmware version
•
Error messages from the last reboot or startup
Use the following procedure to view the status of your phone using the IP Phone UI.
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Phone Status.
3. Select the option you want to view:
•
IP&MAC Address
•
LAN Port
•
PC Port
•
Firmware Info
•
Error Messages
The option you select displays to the LCD. Use the
LCD display.
18
and
keys to scroll the through the
Model 6753i IP Phone User Guide
Finding Your Phone’s IP Address
If you want to access your phone’s options using an Internet browser, you need to enter the IP
address of the phone in the browser to open the Aastra Web UI. Use the following procedure to
find your phone’s IP address.
IP Phone UI
1. Press the
button on the phone to enter the Option List.
2. Select Phone Status and press the 4 key.
3 Phone Status
=Next
=Enter
3. Select "IP&MAC Addresses" and press the 4 key.
1 IP&MAC Addresses
=Next
=Enter
The IP address of your 6753i IP phone displays in the "IP Address" field.
IP Address:
10.40.50.112
=Next
=Exit
Phone Status via the Aastra Web UI
Use the following procedure to view the phone status via the Aastra Web UI.
Aastra Web UI
2. In the Username/Password window, enter your username and password and click
.
Note: For a user, the default user name is “user” and the password field is left
blank.
Model 6753i IP Phone User Guide
19
Phone Status
1. Open your web browser, enter the phone’s IP address or host name into the address field and
press <Enter>.
Phone Status
The Network Status window displays for the IP phone you are accessing.
This Network Status window is view only. It displays the Network Status of your phone which
includes the following:
20
•
Link State, Negotiation, Speed, and Duplex setting for the LAN and PC ports
•
MAC Address
•
Hardware Information
•
Firmware Information
•
SIP Account status
Model 6753i IP Phone User Guide
SIP Account Status
The IP Phones show the SIP registration status on the IP Phone’s Network Status screen in the
Aastra Web UI.
The following is an illustration of the Network Status screen in the Aastra Web UI with SIP status
displayed.
SIP Account Status
Phone Status
Model 6753i IP Phone User Guide
21
Phone Status
The following table describes the status conditions that can display for the account.
Status Condition
Desription
Registered
Displays this status on accounts that HAVE been registered with the SIP proxy
server.
Example:
Backup
Registrar
Line SIP Account
1
9057604603@anasipproxy.aastra.com:5060
Status
Registered
Used?
Yes
where
Account Number is “1”
SIP Account is “9057604603@anasipproxy.aastra.com” on port “5060”
Status is “Registered”
Backup registrar is used (“Yes”)
SIP Error Number
Displays on accounts when registration fails with the SIP proxy server.
Example:
Backup
Registrar
Line
SIP Account
4
9057604601@anasipproxy.aastra.com:5060
Status
401
Used?
No
where
Account Number is “4”
SIP Account is “9057604601@anasipproxy.aastra.com” on port “5060”
Status is “401” - Unregistered if SIP registration fails.
Backup registrar is used (“No”)
22
Model 6753i IP Phone User Guide
Customizing Your Phone
The following paragraphs describe the options available from either the IP Phone UI, the Aastra
Web UI, or both, and provide procedures applicable to the option.
Ring Tones and Tone Sets
You can configure ring tones and ring tone sets on the IP phone.
Ring Tones
There are several distinct ring tones a user can select from to set on the IP phones. You can enable/
disable these ring tones on a global or per-line basis.
The following table identifies the valid settings and default values for each type of configuration
method.
Ring Tones Table
Valid Values
Default Value
IP Phone UI
Global
Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
Silent
Global Setting:
Tone 1
Aastra Web UI
Global:
Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
Silent
Global Setting:
Tone 1
Lines 1 to 9
Per-Line Setting:
Global
Tone 1
Tone 2
Tone 3
Tone 4
Tone 5
Silent
Per-Line Setting:
Global
Model 6753i IP Phone User Guide
Customizing Your Phone
Configuration Method
23
Customizing Your Phone
Ring Tone Sets
In addition to ring tones, you can configure ring tone sets on a global-basis on the IP phone. Ring
tone sets consist of tones customized for a specific country. The ring tone sets you can configure
on the IP phones are:
•
United States (US) (Default - also used in Canada)
•
Mexico
•
Brazil
•
United Kingdom (UK)
•
Italy
•
Germany
•
France
•
Europe (generic tones)
•
Australia
When you configure the country's tone set, the country-specific tone is heard on the phone for
the following:
•
dial tone
•
secondary dial tone
•
ring tone
•
busy tone
•
congestion tones
•
call waiting tone
•
ring cadence pattern
You configure global ring tones and tone sets using the Aastra Web UI and the IP Phone UI.
Configuring Ring Tones and Tone Sets
IP Phone UI
Use the following procedures to configure ring tones and tone sets on the IP phone.
Global configuration only
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Tones.
4. Select Ring Tone.
24
Model 6753i IP Phone User Guide
5. Select the type of ring tone (Tone 1 through Tone 5, or Silent).
6. Select Set and then press 2.
7. Select Tone Set.
8. Select the country for which you want to apply the tone set. Valid values are
Australia, Europe, France, Germany, Italy, UK, Mexico, Brazil, and US. Default is US.
9. Press 4.
The ring tone and tone set you select is immediately applied to the IP phone.
Aastra Web UI
1. Click on Basic Settings->Preferences->Ring Tones.
2. In the "Ring Tones" section, select a country from the "Tone Set" field.
Valid values are Australia, Europe, France, Germany, Italy, UK, Mexico, Brazil, and US.
Default is US.
3. Select a value from the "Global Ring Tone" field.
Note: *See the Ring Tones Table on page 23 for valid values.
For per-line configuration:
4. In the "Ring Tone" section, select a line for which you want to set ring tone.
5. Select a value from the "LineN" field.
Note: See the Ring Tones Table on page 23 for valid values.
6. Click
to save your changes.
Model 6753i IP Phone User Guide
25
Customizing Your Phone
For global configuration:
Customizing Your Phone
Contrast Level
The "Contrast Level" option on the IP phone allows you to set the amount of light that
illuminates the LCD display. Use this option to set the preference of contrast level.
You can set the contrast level using the IP Phone UI only.
Setting Contrast Level
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Contrast Level.
4. Use the 3 and 4 navigation buttons to increase or decrease the intensity of contrast
lighting on the LCD.
5. Press Set to save your selection.
Live Dialpad*
The "Live Dialpad" option on the IP phone turns the Live Dial Pad mode ON or OFF. With live
dial pad ON, the 6753i IP phone automatically dials out and turns ON Handsfree mode as soon
as a dial pad key or programmable key is pressed. With live dial pad OFF, if you dial a number
while the phone is on-hook, lifting the receiver or pressing the
initiates a call to that
number.
*Availability of feature dependant on your phone system or service provider.
You can enable/disable the live dialpad using the IP Phone UI only.
Enabling/Disabling Live Dialpad
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Live Dialpad.
4. Use the Change key to turn the live dialpad ON or OFF.
5. Press Done to save your selection.
26
Model 6753i IP Phone User Guide
Set Audio
The "Set Audio" option on the IP Phone allows you to set the audio mode for your IP phone. It
also allows you to set the volume level of the headset microphone.
You can set Audio on your IP phone using the IP Phone UI only.
Audio Mode
The 6753i allows you to use a handset, a headset, or handsfree mode to handle incoming and
outgoing calls. The audio mode option provides different combinations of these three methods to
provide maximum flexibility in handling calls. There are four audio mode options you can set:
Audio Mode Option Description
This is the default setting. Calls can be made or received using the handset
or handsfree speakerphone. In handset audio mode, pressing the
button on the phone switches to handsfree speakerphone. In Speaker audio
mode, lift the handset to switch to the handset.
Headset
Choose this setting if you want to make or receive all calls using a handset
or headset. Calls can be switched from the handset to headset by pressing
the
button on the phone. To switch from the headset to the handset, lift
the handset.
Speaker/Headset
Incoming calls are sent to the handsfree speakerphone first when the
button is pressed. By pressing the button again, you can switch back
and forth between the handsfree speakerphone and the headset. At
anytime, lifting the handset switches back to the handset from either the
handsfree speakerphone or the headset.
Headset/Speaker
Incoming calls are sent to the headset first when the
button is
pressed. By pressing the button again, you can switch back and forth
between the headset and the handsfree speakerphone. At anytime, lifting
the handset switches back to the handset from either the headset or the
handsfree speakerphone.
Headset Mic Volume
The "Headset Mic Volume" option allows you to set the volume level for the headset microphone.
Setting Audio Mode and Headset Mic Volume
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Set Audio.
4. Select Audio Mode.
Model 6753i IP Phone User Guide
27
Customizing Your Phone
Speaker
Customizing Your Phone
5. Select the audio mode you want to use on your phone. Valid values are:
Speaker
Headset
Speaker/Headset
Headset/Speaker
6. Press Done to save your selection.
7. Select Headset Mic Volume.
8. Select the Low, Medium, or High volume level.
9. Press Done to save your selection.
Time and Date
On the IP phones, you can configure the following:
•
Time and date
•
Time and date format
•
Time zone
•
Daylight savings time
•
Time Servers
Note: Only the Time and Date Formats and Time Servers can be set using the
Aastra Web UI.
Note:
Configuring Time and Date
Use the following procedures to configure the time and date settings on the IP phone.
IP Phone UI
Set Time and Time Format
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Time and Date.
4. Select Set Time.
5. Using the keys on the keypad, enter a time to set on the IP phone. Use the
3 and 4 navigation keys to move backward or forward when entering the time. Use the
"*" key to set either AM or PM.
6. Press Set to save the time setting.
7. Select Time Format.
28
Model 6753i IP Phone User Guide
8. Using the "Change" key, set the Time Format to either a 12 hour format or a 24 hour format.
Valid values are 12h and 24h. Default is 12h.
9. Press Set to save the Time Format you selected.
Set Date and Date Format
1. Select Preferences.
2. Select Time and Date.
3. Select Set Date.
4. Using the keys on the keypad, enter a date to set on the IP phone. Use the
3 and 4 navigation keys to move backward or forward when entering the date.
5. Press Set to save the date setting.
6. Select Date Format.
7. Select a date format from the list of options. Default is Sun Jan 2. Valid values are:
Sun Jan 2 (Default)
•
2-Jan-00
•
2000 01 02
•
02/01/2000
•
02/01/00
•
02-01-00
•
01/.02/00
•
Jan 2
•
2 Jan 2000
•
Sun 2 Jan
•
2 Jan
•
02.01.2000
Customizing Your Phone
•
8. Press Set to save the Date Format setting.
Set Time Zone
1. Select Preferences.
2. Select Time and Date.
3. Select Time Zone.
4. Press * to display a list of Time Zone options.
A list of Time Zones display for different areas of the world.
5. Select a Time Zone that applies to your area.
The default Time Zone is US-Eastern.
Note: For a list of the Time Zones values available on the IP Phone, see
‘Appendix A - Time Zone Codes.”.
Model 6753i IP Phone User Guide
29
Customizing Your Phone
6. Press Set to save the Time Zone setting.
Set Daylight Savings Time
1. Select Preferences.
2. Select Time and Date.
3. Select Daylight Savings.
4. Select a Daylight Savings time from the list of options.
Valid values are:
•
OFF
•
30 min summertime
•
1 h summertime
•
Automatic (Default)
Note: The default for Daylight Savings is Automatic.
5. Press Set to save the Daylight Savings setting.
Set Time Servers
With a valid time server enabled your IP phone will synchronize the time displayed with the
specified configuration server. The phone will use the time from Time Server 1 unless it is not
configured or unavailable, in which case it will move on to Time Server 2, and if neccessary
Time Server 3.
1. Select Preferences.
2. Select Time and Date.
3. Select Time Server.
4. Select from Time Server 1, Time Server 2, or Time Server 3.
5. Enter an IP address or domain name for the time server.
Note: The default for Time Servers is Enabled. The Time Servers can be
Enabled or Diabled only from the Aastra Web UI.
6. Press Set to save the time server setting.
30
Model 6753i IP Phone User Guide
Aastra Web UI
1. Click on Basic Settings->Preferences->Time and Date Setting.
2. In the “Time Format” field, select the time format you want to use on your phone. Valid
values are:
•
12h (12 hour format) (default)
•
24h (24 hour format)
Note: The time and time format you configure display on the phone’s idle
screen.
3. In the “Date Format” field, select the date format you want to use on your phone. Default is
WWW MMM DD. Valid values are:
WWW MMM DD (default)
•
DD-MMM-YY
•
YYYY-MM-DD
•
DD/MM/YYYY
•
DD/MM/YY
•
DD-MM-YY
•
MM/DD/YY
•
MMM DD
•
DD MMM YYYY
•
WWW DD MMM
•
DD MMM
•
DD.MM.YYYY
Note: The date and date format you configure display on the phone’s idle screen.
4. In the “NTP Time Servers” field, enable by checking the checkbox or disable by unchecking
the box (default is enabled).
Model 6753i IP Phone User Guide
31
Customizing Your Phone
•
Customizing Your Phone
5. In the “Time Server 1”, “Time Server 2”, and “Time Server 3” fields, enter IP addresses
or qualified domain names for the primary, secondary, and tertiary time servers.
Note: Time Servers can only be entered if NTP Time Servers is enabled.
6. Click
to save your changes.
Language
The IP phones support several different languages. You can have the IP Phone UI and the Aastra
Web UI display in a specific language as required. When you set the language to use, all of the
display screens (menus, services, options, configuration parameters, etc.) display in that
language. The IP phones support the following languages:
•
•
•
•
•
•
•
•
English (default)
French (Canadian)
French (European)
Spanish (Mexican)
Spanish (European)
German
Italian
Portuguese
You can also configure the language to use when inputing values in the Aastra Web UI and the
IP Phone UI.
Specifying the Language to Use
Once the language pack(s) are available on your phone from your System Administrator, you
can specify which language to use on the phone and/or the Aastra Web UI.
Note: All languages may not be available for selection. The available languages
are dependant on the language packs currently loaded to the IP phone.
IP Phone UI
Use the following procedure to specify which language to use for the IP Phone UI.
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Language.
4. Select Screen Language.
The language setting displays a check mark indicating this is the current language on the IP
Phone.
32
Model 6753i IP Phone User Guide
5. Using the 2 and 5 keys, scroll through the languages. Valid values are:
•
English (default)
•
Français (French)
•
Español (Spanish)
•
Deutsch (German)
•
Italiano (Italian)
•
Português (Portguese)
Note: All languages may not be available for selection. The available languages
are dependant on the language packs currently loaded to the IP phone. English is
the default language and cannot be changed or removed. For more information
about loading language packs, see your System Administrator.
6. Press Set to set the language on the phone.
The change is dynamic. When you exit the Options Menu, the phone displays all menu items
in the language you selected.
Customizing Your Phone
Model 6753i IP Phone User Guide
33
Customizing Your Phone
Aastra Web UI
Note: You must have the language pack(s) already loaded to your phone in order
to use them. For more information about loading language packs, see your
System Administrator.
1. Click on Basic Settings->Preferences->Language Settings.
2. In the “Webpage Language” field, select a language to apply to the Aastra Web UI. The IP
phone supports the following languages:
•
English (default)
•
Français (French)
•
Español (Spanish)
•
Deutsch (German)
•
Italiano (Italian)
•
Português (Portguese)
Note: All languages may not be available for selection. The available languages
are dependant on the language packs currently loaded to the IP phone by your
System Administrator. English is the default language and cannot be changed or
removed.
3. Click
to save your settings. The change is dynamic. The Aastra Web UI displays all
screens in the language you selected.
34
Model 6753i IP Phone User Guide
Language Input
The 6753i supports text and character inputs in various languages (English, German, French,
Spanish, and Italian). Inputting textual or character information into the IP Phone UI can be done
using the keypad on the phone. You enable the Language Input feature using the Aastra Web UI or
the IP Phone UI. You can then use text and characters in a specific language when performing
inputs on the phone.
The following tables identify the language characters that you can use to enter text and characters
on the 6753i.
Keypad Input Alphabet Tables
English
Key
Uppercase Characters
Lowercase Characters
0
0
0
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2
abc2
3
DEF3
def3
4
GHI4
ghi4
5
JKL5
jkl5
6
MNO6
mno6
7
PQRS7
pqrs7
8
TUV8
tuv8
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
Key
Uppercase Characters
Lowercase Characters
0
0
0
1
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2ÀÂÇÁÅÆ
abc2àâçáåæ
3
DEF3ÉÈÊË
def3éèêë
Customizing Your Phone
1
French
4
GHI4ÎÏ
ghi4îï
5
JKL5
jkl5
6
MNO6ÑÓÒÔÖ
mno6ñóòôö
7
PQRS7
pqrs7
8
TUV8ÚÙÛÜ
tuv8úùûü
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
Model 6753i IP Phone User Guide
35
Customizing Your Phone
Spanish
Key
Uppercase Characters
Lowercase Characters
0
0
0
1
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2ÁÀÇ
abc2áàç
3
DEF3ÉÈ
def3éè
4
GHI4ÏÍ
ghi4ïí
5
JKL5
jkl5
6
MNO6ÑÓÒ
mno6ñóò
7
PQRS7
pqrs7
8
TUV8ÚÜ
tuv8úü
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
Key
Uppercase Characters
Lowercase Characters
0
0
0
1
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2ÄÀ
abc2äà
3
DEF3É
def3é
4
GHI4
ghi4
5
JKL5
jkl5
6
MNO6Ö
mno6ö
7
PQRS7ß
pqrs7ß
8
TUV8Ü
tuv8ü
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
German
36
Model 6753i IP Phone User Guide
Italian
Key
Uppercase Characters
Lowercase Characters
0
0
0
1
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2ÀCÇ
abc2àcç
3
DEF3ÉÈË
def3éèë
4
GHI4
ghi4
5
JKL5
jkl5
6
MNO6ÓÒ
mno6óò
7
PQRS7
pqrs7
8
TUV8Ù
tuv8ù
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
Key
Uppercase Characters
Lowercase Characters
0
0
0
1
1.:;=_,-'&()
1.:;=_,-'&()
2
ABC2ÁÀÂÃÇ
abc2áàâãç
3
DEF3ÉÊ
def3éê
4
GHI4Í
ghi4í
5
JKL5
jkl5
6
MNO6ÓÔÕ
mno6óôõ
7
PQRS7
pqrs7
8
TUV8ÚÜ
tuv8úü
9
WXYZ9
wxyz9
*
* <SPACE>
* <SPACE>
#
#/\@
#/\@
Portguese
Customizing Your Phone
Model 6753i IP Phone User Guide
37
Customizing Your Phone
Configuring Language Input Using the IP Phone UI
You can configure the language you use for inputting on the phone by setting the Input
Language option. The default input language setting is English. You can change this setting
using the IP Phone UI or the Aastra Web UI.
Example
= Next
= Next
= Enter
Language Option
Input Language
English
= Next
= Set
2. Input Language
7. Language
= Enter
Input Language Option
Select an Input
Language
IP Phone UI
Use the following procedure to change the input language using the IP Phone UI.
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Language.
4. Select Input Language.
Select the language you want to use when inputting text and characters into the IP Phone UI.
Valid values are:
•
•
•
•
•
•
English (default)
Français (French)
Español (Spanish)
Deutsch (German)
Italiano (Italian)
Português (Portguese)
Note: Available input languages are dependent on the configuration enabled by
your System Administrator.
5. Press Set when you have selected an input language.
Aastra Web UI
Use the following procedure to set the input language using the Aastra Web UI.
38
Model 6753i IP Phone User Guide
1. Click on Basic Settings-> Preferences->Language Settings.
2. Select a language from the "Input Language" field. Setting this field allows you to specify
the language to use when entering text and characters in the Aastra Web UI and IP Phone UI.
Valid values are:
•
•
•
•
•
•
English (default)
Français (French)
Español (Spanish)
Deutsch (German)
Italiano (Italian)
Português (Portguese)
Note: All languages may not be available for selection. The available input
languages are dependant on the configuration enabled by your System
Administrator.
Model 6753i IP Phone User Guide
39
Customizing Your Phone
3. Click
to save your settings. The change is dynamic. The Aastra Web UI and IP Phone
UI allow you to enter text and characters in the language you selected.
Customizing Your Phone
Latin 2 Character Set
The 6753i includes support for ISO 8859-2 (Latin2) of multi-national languages when
displaying and inputing in the IP Phone UI and the Aastra Web UI.
UTF-8 is also compatible with XML encoding on the IP Phones.
The following table illustrates the Latin 2 character set used on the 6753i IP Phone.
40
Model 6753i IP Phone User Guide
User Password
This category allows you to change the user password for your phone. Changing your password
ensures that only you can alter your phone settings, and helps keep your system secure. You can
change your user password using the IP Phone UI or the Aastra Web UI.
If you change the password
Then you need to:
using the IP Phone UI,
use that new password to log into
the Aastra Web UI.
using the Aastra Web UI,
use that new password when
changing the user password via the
IP Phone UI.
Note: Valid values when creating or changing a password are 0 to 4294967295
(integers only; symbols and alpha characters are not allowed). Default password
is an empty string "" (field is blank).
Setting a User Password
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select User Password and press Enter.
3. At the "Current Password" prompt, enter the current user password and press Enter.
4. At the "New Password" prompt, enter the new user password and press Enter.
Customizing Your Phone
5. At the "Enter Again" prompt, re-enter the new user password and press Enter.
A message, "Password Changed" displays on the screen.
Aastra Web UI
1. Click on Operation->User Password.
2. In the "Current Password" field, enter the current user password.
Note: By default, the user name is “user” (all lowercase) and the password field
is left blank.
Model 6753i IP Phone User Guide
41
Customizing Your Phone
3. In the "New Password" field, enter the new user password.
4. In the "Password Confirm" field, enter the new user password again.
5. Click
to save your changes.
Resetting a User Password
If you forget your password, you can reset it and enter a new password. The reset user password
feature resets the password to the factory default which is blank (no password).
You can reset a user password using the Aastra Web UI only.
Note: Valid values when creating or changing a password are 0 to 4294967295
(integers only; symbols and alpha characters are not allowed). Default password
is an empty string "" (field is blank).
Reset a User Password
Use the following procedure to reset a user password.
Aastra Web UI
1. Click on Operation->Phone Lock.
2. In the "Reset User Password" field, click
The following screen displays.
3.
4.
5.
6.
42
.
In the "Current Password" field, leave this blank.
In the "New Password" field, enter a new password.
In the "Password Confirm" field, re-enter your new user password.
Click
to save your settings.
Model 6753i IP Phone User Guide
Restarting Your Phone
You may want to restart your phone to check for updates for your phone on the server. You may
occasionally need to restart your phone to set changes or updates to your phone or network
settings. You may also need to restart your phone if you have been asked to do so by your System
Administrator, or should you experience any unexpected behavior.
IP Phone UI
1. Press the
button on the phone to enter the Options List.
2. Select Restart Phone.
3. Press # to confirm the restart of the phone. If you do not wish to restart your phone, press the
3 key to cancel.
Note: Your phone is out of service temporarily during the restart and
downloading process.
Aastra Web UI
1. Click on Operation->Reset.
Customizing Your Phone
2. Click
.
3. Click OK at the confirmation prompt.
Model 6753i IP Phone User Guide
43
Customizing Your Phone
Phone Lock
You can lock your phone to prevent the phone from being used or configured. You can lock the
phone using any of the following:
•
At the path Options->Phone Lock on the IP Phone UI.
•
At the path Operations->Phone Lock on the Aastra Web UI.
•
At a configured key on the phone. For more information about configuring a Lock/Unlock
key on your phone, see “Phone Lock Key” on page 104.
In the Aastra Web UI, the Operation->Phone Lock path also allows you to perform the
following:
•
Reset a user password. Clicking on the “Reset” button in the “Reset User Password” field
displays a screen that allows you to enter and save a new user password.
•
Set an emergency dial plan. An emergency dial plan can be 911, 999, 112, 110 or all of the
above. The default emergency dial plan is 911|999|112|110.
The following procedures describe locking the phone, setting an emergency dial plan, and
resetting the user password.
Locking/Unlocking a Phone
Use the following procedures to lock an IP phone and prevent it from being used or configured.
IP Phone UI
Lock the Phone
1. Press
on the phone to enter the Options List.
2. Select Phone Lock and press Enter.
3. At the "Lock the phone?" prompt, press Lock.
The message "Phone is locked" displays.
Unlock the Phone
1. Press
on the phone to enter the Options List.
2. At the prompt, "Password:", enter your user password and press Enter.
The phone unlocks.
44
Model 6753i IP Phone User Guide
Aastra Web UI
1. Click on Operation->Phone Lock.
Lock the Phone
2. In the "Lock the Phone?" field, click
.
The phone locks dynamically and displays the following message:
"Phone is locked".
Unlock the Phone
3. Click on Operation->Phone Lock.
4. In the "Unlock the Phone?" field, click
.
The phone unlocks dynamically and displays the following message:
"Phone is unlocked".
Public telephone networks in countries around the world have a single emergency telephone
number (emergency services number), that allows a caller to contact local emergency services for
assistance when required. The emergency telephone number may differ from country to country. It
is typically a three-digit number so that it can be easily remembered and dialed quickly. Some
countries have a different emergency number for each of the different emergency services.
You can specify the digits to dial on the IP phone for contacting emergency services. Once you
specify the emergency number(s) on the phone, you can dial those numbers directly on the dial pad
when required and the phone automatically dials to those emergency services.
Note: Contact your local phone service provider for available emergency
numbers in your area.
Model 6753i IP Phone User Guide
45
Customizing Your Phone
Defining an Emergency Dial Plan
Customizing Your Phone
The following table describes the default emergency numbers on the IP phones.
Emergency
Number
Description
911
A United States emergency number
999
A United Kingdom emergency number
112
An international emergency telephone number for GSM mobile phone
networks.
In all European Union countries it is also the emergency telephone number
for both mobile and fixed-line telephones.
110
A police and/or fire emergency number in Asia, Europe, Middle East, and
South America.
You can set the emergency dial plan using the Aastra Web UI.
Define an Emergency Dial Plan
Use the following procedure to specify the numbers to use on your phone for dialing emergency
services in your area.
Aastra Web UI
1. Click on Operation->Phone Lock.
2. In the "Emergency Dial Plan" field, enter the 3-digit number used in your local area to
contact emergency services. For multiple numbers, enter a “|” between each emergency
number. For example:
911|110
Default for this field is 911|999|112|110.
3. Click
to save the emergency dial plan to your phone.
Reference
For more advanced options you can set on your phone, see “Additional Features” on page 162.
46
Model 6753i IP Phone User Guide
Line Keys and Programmable Keys
This section describes the Multiple Line/Call Appearance Keys (L1, L2, and L3) and the
customizable programmable keys located at the top left on the phone.
Programmable Keys
Multiple Line/
Call Appearance
Keys
The 6753i has 3 hard line/call appearance keys each with a corresponding status light.
These line/call appearance buttons and lights can represent physical lines, calls for your extension
or calls from a group that your extension is part of. By pressing a line/call appearance button, you
connect to the line or a call it represents. The line/call appearance light indicates the status of that
line or call. When the phone is taken off-hook, the phone automatically selects a line for you.
Line/Call Appearance
Light Behavior
Line/Call
Appearance Status
Off
Idle line or no call
activity
Light flashes quickly
Ringing
Light is solid
Connected
Light flashes slowly
Hold
When you have more than one call, you can use the left and right navigation buttons (3 and 4) to
scroll left and right to the different call information. Icons 3 and 4 appear if there is call
information either left, right or both sides of the current information you are viewing.
The display shows which line the call information is referring to (L1, L2, L3, etc.), the Caller ID
information (name and number, if available), the call status (Connected, Ring, Hold, etc.) and the
timer specific to that call.
Model 6753i IP Phone User Guide
47
Line Keys and Programmable Keys
Multiple Line and Call Appearance Keys
Line Keys and Programmable Keys
Programmable Keys
There are six function keys on the 6753i phone, all 6 of which are programmable, located to the
left of the paper label.
Programmable
Keys after Admin Unlocks
Save Key
Delete Key
Directory
Callers List
Transfer
Conference
Programmable
Keys
Note: The SAVE and DELETE keys are programmable ONLY after an
Administrator has unlocked these keys. For more information about the SAVE
and DELETE keys, see “Configurable Save and Delete Keys” on page 196.
Note: If a M670i Expansion Module(s) is attached to the phone, you can
configure 36 additional keys on each Expansion Module (Phone allows up to 3
expansion modules totaling up to 108 additional keys). For more information
about expansion modules, see “Model M670i Expansion Module” on page 200.
You can use the Aastra Web UI only, to configure key functions. The following table lists the
functions you can set on the programmable keys and provides a description for each function.
48
Key Function
Description
None
Indicates no setting for the key.
Line
Indicates the key is configured for line use.
Speeddial
Indicates the key is configured for speeddial use. You can also configure a prefix
for a speeddial number.
Do Not Disturb
Indicates the key is configured for "do not disturb" on the phone.
Busy Lamp Field
(BLF)
Indicates the key is configured for Busy Lamp Field (BLF) use. User can dial out
on a BLF configured key.
(Maximum of 50 BLFs allowed on M670i Expansion Module.)
BLF List
Indicates the key is configured for BLF list use. User can dial out on a BLF List
configured key.
Auto Call
Distribution (ACD)
(For Sylantro Servers)
Indicates the key is configured to allow the Sylantro server to distribute calls
from a queue to registered IP phone users (agents).
Model 6753i IP Phone User Guide
Key Function
Description
Directed Call Pickup
(DCP)/
(For Sylantro Servers)
Indicates the key is configured to allow you to intercept - or pickup - a call on a
monitored extension(s).
Group Call Pickup
(GCP)
Indicates the key is configured to accept an XML application for accessing
customized XML services. You can also specify an XML key URL for this option.
Flash
Indicates the key is set to generate a flash event when it is pressed on the 6753i.
The IP phone generates flash events only when a call is connected and there is
an active RTP stream (for example, when the call is not on hold).
Sprecode
Indicates the key is configured to automatically activate specific services offered
by the server. For example, if the sprecode value of *82 is configured, then by
pressing the Sprecode key, *82 automatically activates a service provided by the
server. Contact your System Administrator for available services.
Park
Indicates the key is configured to park incoming calls when pressed.
Pickup
Indicates the key is configured to pick up parked calls when pressed.
Last Call Return (lcr)
Indicates the key is configured for “last call return” when pressed.
Call Forward
Indicates the key is configured as a Call Forward key. When pressed, the IP
Phone UI displays the Call Forward menus.
BLF/Xfer
Indicates the key is configured as a simplified BLF key and a transfer key. You
can use this key to perform the BLF function, or you can use it as a transfer key
to transfer calls.
Speeddial/Xfer
Indicates the key is configured as a simplified speeddial key and a transfer key.
You can use this key to perform speeddial functions, or you can use it as a
transfer key to transfer calls.
Speeddial/Conf
Indicates the key is configured as a speeddial key and a conference key. You
can use this key to speeddial from within a conference call, and add the new call
directly to the conference.
Directory
(Key 3 by Default)
Indicates the key is configured to access the Directory List.
Callers List
(Key 4 by Default)
Indicates the key is configured to access the Callers List.
Transfer
(Key 5 by Default)
Indicates the key is configured as a Transfer key (Xfer) for transferring calls.
Conference
(Key 6 by Default)
Indicates the key is configured as a Conference key (Conf).
Intercom
Indicates the key is configured to be used for intercom calls.
Services
Indicates the key is set to access Services, such as, Directory List, Callers List,
Voicemail, or any other XML applications set up by your System Administrator.
Model 6753i IP Phone User Guide
Line Keys and Programmable Keys
XML
49
Line Keys and Programmable Keys
Key Function
Description
Phone Lock
Indicates the key is configured as a phone lock key, allowing you to press this
key to lock/unlock the phone.
Paging
Indicates the key is configured as a Paging key. When pressed, the phone can
send Real Time Transport Protocol (RTP) streams from a pre-configured
multicast address without involving SIP signaling. You can also receive RTP
streams from pre-configured multicast addresses (can specify up to 5
addresses) using the "Paging Listen Addresses" at the path,
Basic Settings->Preferences->Group Paging RTP Settings in the Aastra Web
UI. For more information about setting this parameter, see “Group RTP Paging
(receives RTP streams)” on page 184.
Programmable keys can also be set up to quickly to access features such as Call Return (*69) or
Voicemail.
Note: Quick access features like Call Return and Voicemail must first be configured
on your PBX in order to work on your phone. See your System Administrator for
more information.
The following paragraphs describe how to configure each function listed in the previous table.
50
Model 6753i IP Phone User Guide
Line Key
You can set a programmable key or an expansion module key to act as a line/call appearance key
on the 6753i. The key acts as a line that behaves the same as a hard line key (L1, L2, and L3). For
more information about the behavior of line keys, see “Multiple Line and Call Appearance Keys”
on page 47.
You use the Aastra Web UI to set a Line key.
Configuring a Line Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
Line Keys and Programmable Keys
Use the following procedure to set a Line key on your phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Line to apply to the key.
4. In the "Line" field, select a line for which to apply this key. Valid values are 4 through 9.
5. Click
to save your changes.
Model 6753i IP Phone User Guide
51
Line Keys and Programmable Keys
Creating a Speeddial Key
The normal function of the speeddial option allows you to dial a number quickly by pressing a
key configured for speeddialing. You can program the keys on the 6753i to speeddial outside
numbers, dial directly to another person’s line or extension, or set up to quickly access features
such as Caller ID (*69), Voicemail.
The speeddial function can be set using the IP Phone UI or the Aastra Web UI.
Note: You can use a speeddial key while on an active call by placing the active
call on hold first, and then pressing the speeddial key.
You can create speeddial keys using any of the following methods:
•
Using the Aastra Web UI at the paths:
— Operation->Programmable Keys
— Operation->Expansion Module
— Operation->Speeddial Edit
•
By pressing and holding a programmable key, expansion module key, or keypad key.
•
Using the IP Phone UI at the path:
— Options->Preferences->Speed Dial Edit
Speeddial Prefix
The speeddial feature also allows you to specify a preset string of numbers followed by a “+”
that the phone dials automatically after pressing the speeddial key. You can use this feature for
numbers that contain long prefixes.
For example, if you had the following speeddial configuration in the Aastra Web UI:
Key 1
Type=speeddial
Label=Europe Office
Value=1234567+
Line=2
then, after you press key 1 on the phone, the prefix number displays on the phone screen. The
phone proceeds to dial the prefix number automatically and pauses for you to enter the
remaining phone number using the keypad on the phone.
You can save up to 7 speeddial numbers on the 6753i.
52
Model 6753i IP Phone User Guide
Use the following procedures to set speeddial on the 6753i IP phone.
Press-and-Hold to Create a Speeddial
(applicable to programmable keys, keypad keys, expansion module keys)
IP Phone UI
Pressing and holding down a programmable key, expansion module key, or keypad key on the
phone initiates a speeddial feature.
Note: When creating a speeddial for a key on the IP Phone, you must select a
key that has no preassigned function (key must be set to None). Pressing and
holding a programmable key, expansion module key, or keypad key that currently
has a speeddial setting, allows you to edit that speeddial setting.
1. Press a programmable key, expansion module key, or a number key on the keypad for 3
seconds. A screen displays with the prompt, "Enter number>".
Speeddial
Enter number> 3456
After entering the number, the prompt, "Use Save to end" displays on the screen.
3456
Use Save to end
3. Press Save to save the number as a speeddial key.
By default, the phone automatically assigns the speeddial key to line 1 if available. To select a
different line, press the Change key and select a different line, or use the phone’s keypad to
select a number (1-9), or use the 2 and 5 to make your selection.
Line: 1
Change
Use Save to end
4. Press Save to save the speeddial key to the line specified.
Note: Press and hold a speeddial key to edit that speeddial key. If you try to edit
a digit key set to “Empty” or “None”, the phone proceeds to enter the “Add a
Speeddial Key” process. For more information about editing a speeddial key, see
“On the 6753i, you can edit a speeddial key using any of the following methods:”
on page 58.
Model 6753i IP Phone User Guide
53
Line Keys and Programmable Keys
2. Enter a phone number or extension to assign to that speeddial key.
The following example illustrates the screen display:
Line Keys and Programmable Keys
Creating a Speeddial Using the Speed Dial Edit Option
You can use the IP Phone UI at the path, Options->Preferences->Speeddial Edit, to create a
speeddial key.
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select Preferences.
3. Select Speed Dial Edit.
The following prompt displays:
"Press SD button"
All current speeddial key LEDs flash RED (for programmable keys and expansion module
keys). All other function key LEDs turn off, during this process. After you press a speeddial
key for editing, the phone restores all key LEDs to their previous state.
Note: If you select a key that is currently set as a speeddial key, the speeddial
information displays for you to edit.
4. Press a non-configured programmable key, keypad key, or expansion module key.
5. Enter a phone number or extension to assign to that speeddial key.
The following example illustrates the screen display:
Speeddial
Enter number> 3456
After entering the number, the prompt, "Use Save to end" displays on the screen.
3456
Use Save to end
6. Press Save to save the number as a speeddial key.
By default, the phone automatically assigns the speeddial key to line 1 if available. To select
a different line, press the Change key and select a different line, or use the phone’s keypad
to select a number (1-9), or use the 2 and 5 to make your selection.
Line: 1
Change
Use Save to end
7. Press Save to save the speeddial key to the line specified.
54
Model 6753i IP Phone User Guide
Creating a Speeddial Key Using the Save Key
IP Phone UI
Use the following procedure to create a speeddial key using the Save key. Use the following
illustration for reference.
Save Key
Programmable
Keys
Save to?
2. Select a programmable key or expansion module key you want to save to.
3. At the "Enter Number" prompt, use the dial pad key to enter the number.
Enter Number >
5553491234
4. Press the Save key to save the speeddial configuration.
5. At the "Enter Name" prompt, use the dial pad keys to select the letters. Continue to press the
number key to access the next letter for that key (i.e. press 2 three times to access C). Press 4
to move to the next space, or wait a moment and the cursor automatically advances. To insert a
space between letters, press 4. To backspace and erase a mistake, press 3 or the Delete key.
You can save up to 16 letters and numbers on each programmable key entry.
Enter Name >
John Smith
Model 6753i IP Phone User Guide
55
Line Keys and Programmable Keys
1. Press the Save key. The screen displays "Save to?"
Line Keys and Programmable Keys
6. Press the Save key to finish.
Saved Memory key
5553491234
Creating a Speeddial Using a Programmable Key or Expansion Module Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Speeddial to apply to the key.
4. In the "Value" field, enter the phone number, extension, or speeddial prefix to apply to this
hard key. If you enter a speeddial prefix, you must enter the "+" character at the end of the
prefix number (for example, "123456+").
5. In the "Line" field, select a line for which to apply the speeddial to. Valid values are 1
through 9.
6. Click
56
to save your changes.
Model 6753i IP Phone User Guide
Creating Speeddial Key Using “Keypad Speeddial” in the Aastra Web UI
Aastra Web UI
1. Click on Operation->Keypad Speeddial..
3. In the input box, enter the phone number, extension, or speeddial prefix to apply to this Digit
key. If you enter a speeddial prefix, you must enter the "+" character at the end of the prefix
number (for example, "123456+").
4. Click
to save your changes.
Saving an Entry from the Redial, Callers, or Directory Lists to a
Speeddial Key
IP Phone UI
Use the following procedure to save an entry from your Directory List, Callers List, or Redial List
on the IP phone.
Save Key
Directory List Key
Callers List Key
Redial List Key
Model 6753i IP Phone User Guide
57
Line Keys and Programmable Keys
2. Select from "Digit 1" through "Digit 9".
Line Keys and Programmable Keys
1. Press the Directory List, Callers List, or Redial List key. From the Directory List, Callers
List, or Redial List, scroll through the list to find the name and number that you wish to save
to your speeddial.
2. Press the Save key.
3. Press the selected speed dial. If the name is displayed with the number, both are saved to the
speed dial. If no name is displayed, you can enter the name using the phone’s key pad.
Editing Speeddial Keys
On the 6753i, you can edit a speeddial key using any of the following methods:
•
Using the Aastra Web UI at the path:
— Operation->Programmable Keys
— Operation->Expansion Module Keys
— Operation->Keypad Speed Dial
•
Using the IP Phone UI at the path:
— Options->Preferences->Speed Dial Edit.
The following illustration shows the path in the 6753i IP Phone UI for editing a speeddial key.
Preferences
1. Tones
2. Contrast Level
3. Speed Dial Edit
4. Live Dialpad
5. Set Audio
6. Time and Date
7. Language
Next
Enter
Speed Dial Edit:
Press SD button
555-1212
Use Save to end
Press the Speeddial Key
(LED for Speeddial Key
flashes)
Edit and Save the
Speeddial
Speed Dial Edit Option
IP Phone UI
Use the following procedure to edit a speeddial key from the IP Phone UI.
Note: *A speeddial key must be already configured on the phone to edit the key.
1. Press
on the phone to enter the Options List.
2. Select Preferences.
58
Model 6753i IP Phone User Guide
3. Select Speed Dial Edit.
All current speeddial key LEDs flash RED (for programmable keys and expansion module
keys). All other function key LEDs turn off, during this process. After you press a speeddial
key for editing, the phone restores all key LEDs to their previous state.
4. Press a speeddial key you want to edit.
The speeddial edit screen displays.
Notes:
1. If a number on the keypad is setup as a speeddial key, pressing the applicable
number in the speeddial editing process also displays the speeddial edit screen.
The edit screen allows you to change the Speeddial Number and Line setting.
2. If you press a key that is NOT setup as a speeddial key, the phone displays an
“Invalid Key” message. However, if you press-and-hold an empty keypad key,
programmable key, or expansion module key that is set to "NONE", it initiates the
“Add a Speeddial Key” process allowing you to setup a new speeddial key. For
more information, see “Press-and-Hold to Create a Speeddial (applicable to
programmable keys, keypad keys, expansion module keys)” on page 53.
5. Edit the speeddial information as applicable and press SAVE.
Line Keys and Programmable Keys
Notes:
1. You can cancel out of the speeddial editing process at any time without
saving, by pressing the
key.
2. You can also use the (up arrow) key to cancel when in Extension editing or the
3 (left arrow) key to cancel if in Line editing. Pressing either of these keys
displays the idle screen.
On the 6753i, you can remove the Speeddial Key by erasing the speeddial number
digits (leaving the speeddial value blank) and then press SAVE or the (right
arrow) key. Use the left arrow key to delete the digits.
Model 6753i IP Phone User Guide
59
Line Keys and Programmable Keys
Editing a Speeddial on a Programmable Key or Expansion Module Key
Aastra Web UI
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select the key configured for speeddial.
3. In the "Value" field, edit the phone number, extension, or speeddial prefix to apply to this
hard key. If you enter a speeddial prefix, you must enter the "+" character at the end of the
prefix number (for example, "123456+").
4. If required in the "Line" field, select a line for which to apply the speeddial to. Valid values
are 1 through 9.
5. Click
to save your changes.
Note: You can delete a speeddial key by removing the information from the
"Value" field.
60
Model 6753i IP Phone User Guide
Editing a Speeddial Using “Keypad Speeddial” in the Aastra Web UI
Aastra Web UI
1. Click on Operation->Keypad Speeddial..
3. In the input box, edit the phone number, extension, or speeddial prefix for this Digit key. If you
enter a speeddial prefix, you must enter the "+" character at the end of the prefix number (for
example, "123456+").
4. Click
to save your changes.
Model 6753i IP Phone User Guide
61
Line Keys and Programmable Keys
2. Select from "Digit 1" through "Digit 9".
Line Keys and Programmable Keys
Do Not Disturb (DND) Key
The IP phones have a feature you can enable called "Do not Disturb (DND). The DND function
allows you to turn "do not disturb" ON and OFF.
Note: You can configure DND using the Aastra Web UI only.
If DND is ON, callers calling into the phone hear a busy signal or a message, depending on how
your System Administrator set up the configuration server. The second line on the screen of the
IP phone shows when DND is set.
If the phone shares a line with other phones, only the phone that has DND configured is affected.
You can set DND on the programmable keys or expansion module keys using the Aastra Web UI
only. DND is not configurable from the IP phone UI.
Configuring a DND Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select do not disturb to apply to this key.
62
Model 6753i IP Phone User Guide
Busy Lamp Field (BLF) Key
The BLF feature on the IP phones allows a specific extension to be monitored for state changes.
BLF monitors the status (busy or idle) of extensions on the IP phone.
Note: The BLF setting is applicable to the Asterisk server only.
Example
A Supervisor configures BLFs on his phone for monitoring the status of a worker’s phone use
(busy or idle). When the worker picks up his phone to make a call, a busy indicator on the
Supervisor’s phone shows that the worker’s phone is in use and busy.
On the 6753i, the busy and idle indicators are the LEDs next to each BLF key. The LED
illuminates steady to indicate the monitored line is off-hook or unregistered. The LED goes off
when the line is idle.
Note: You can also use a BLF configured key to dial out. Contact your System
Administrator for more information
Model 6753i IP Phone User Guide
63
Line Keys and Programmable Keys
You can set BLF on the programmable keys or expansion module keys using the Aastra Web UI
only. BLF is not configurable from the IP phone UI.
Line Keys and Programmable Keys
Configuring a BLF Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select BLF to apply to this key.
4. In the "Value" field, enter the phone number or extension you want to monitor.
5. In the "Line" field, select a line for which to apply to this key. Valid values are Global (for
all lines), or 1 through 9.
6. Click
64
to save your changes.
Model 6753i IP Phone User Guide
BLF List Key
(For use with the BroadSoft Broadworks Rel 13 or higher platform only)
The BLF\List feature on the IP phones is specifically designed to support the BroadSoft
Broadworks Rel 13 Busy Lamp Field feature.
This feature allows the IP phone to subscribe to a list of monitored users defined through the
BroadWorks web portal.
Note: Your System Administrator must have BLF List enabled on the
BroadWorks Server. Contact your System Administrator for more information.
In addition to monitoring the idle and busy state, the BLF\List feature also supports the ringing
state. On the 6753i phone, the LED lights next to each BLF key illuminate steady to indicate the
monitored line is off-hook or unregistered. The LED goes off when the is idle. When the
monitored extension is ringing, the LED flashes.
Example
A receptionist has a 6753i running Broadsoft firmware that subscribes to a list of extensions from
the BroadWorks Application Server. On the 6753i running Broadsoft firmware, the key LEDs
illuminate either flashing, solid, or turn off depending on the state of those extensions.
Note: The Broadworks BLF feature is not the same as the Broadworks Shared
Call Appearance (SCA) feature and does not permit call control over the
monitored extension.
Model 6753i IP Phone User Guide
65
Line Keys and Programmable Keys
Note: You can use a BLF\List configured key to dial out.
Line Keys and Programmable Keys
Configuring a BLF List Key
Aastra Web UI
The BLF List function can be configured on the 6753i using the Aastra Web UI only.
If you set a key to use BLF/List, you must also enter a BLF List URI at
Operation->Programmable Keys->Services. The BLF List URI is the name of the BLF list
defined on the BroadSoft BroadWorks Busy Lamp field page for your particular user. For
example, my480i-blf-list@as.broadworks.com. The value of the BLF\List URI parameter must
match the list name configured. Otherwise, no values display on the 6753i screen and the feature
is disabled.
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select "BLF\List" (BroadSoft BroadWorks).
4. In the "Line" field, select a line number that is actively registered to the appropriate SIP
proxy you are using. Valid values are Global (for all lines), or 1 through 9.
66
Model 6753i IP Phone User Guide
5. In the "BLF List URI" field, enter the name of the BLF list defined on the BroadSoft
BroadWorks Busy Lamp field page for your particular user. For example,
my6753i-blf-list@as.broadworks.com.
Note: Contact your System Administrator for the BLF List URI.
6. Click
to save your changes.
Line Keys and Programmable Keys
Model 6753i IP Phone User Guide
67
Line Keys and Programmable Keys
Flash Key
You can set a programmable key or expansion module key to generate a flash event when it is
pressed on the 6753i. You do this by setting the key to "flash". The IP phone generates flash
events only when a call is connected and there is an active RTP stream (for example, when the
call is not on hold).
Configuring a Flash Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select flash.
4. Click
68
to save your changes.
Model 6753i IP Phone User Guide
Automatic Call Distribution (ACD) Key (for Sylantro Servers)
The 6753i and any attached Expansion Modules support Automatic Call Distribution (ACD) for
Sylantro servers. The ACD feature allows the Sylantro server to distribute calls from a queue to
registered IP phone users (agents).
To use the ACD feature on an IP phone, you must first configure an ACD key or Expansion
Module key. When you want to subscribe to a queue (in order to receive incoming calls), you press
the ACD key and the IP phone UI prompts you to specify the following information:
•
User ID: the phone number(s) used to login into the queue.
•
Password: the password used to login to the queue.
•
Available/unavailable: Shows the current status of the IP phone. Specifies if the IP phone
user is available/unavailable to receive a call from the queue.
Note: Your System Administrator must provide you with your User ID and
Password to access the applicable phone queue.
When you are on an active call, or you miss a call, the server automatically changes the phone’s
status to unavailable. The server updates it’s database with this new information and no longer
distributes calls to the phone. The phone remains in this "unavailable" state until:
•
you make yourself “available” again by pressing the "Available" key.
•
an ACD timer expires (set by your System Administrator).
You can also choose to manually change the phone status to unavailable by pressing the
"Unavailable" key on the phone.
Note: It is recommended you configure no more than a single ACD key,
programmable key, or expansion module key per IP phone.
Model 6753i IP Phone User Guide
69
Line Keys and Programmable Keys
After creating an ACD key, you are ready to receive calls from a queue on the server. You must
press the ACD key and then log in by entering your User ID and Password. An "Available" key
displays allowing you to make your phone available to accept these calls.
Line Keys and Programmable Keys
Configuring an Automatic Call Distribution (ACD) Key
Use the following procedure to configure ACD on the 6753i IP Phone.
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Automatic call distribution.
4. In the "Line" field, select a line to apply Automatic call distribution. Valid values are 1
through 9.
Note: It is recommended you configure no more than a single ACD
programmable key or expansion module key per IP phone.
5. Click
70
to save your changes.
Model 6753i IP Phone User Guide
Using the ACD Feature on your IP Phone
The ACD feature allows you to login to a phone queue in order to receive distributed calls on your
IP phone. To login to a phone queue, you must preconfigure an ACD key on your IP Phone as
described in the previous procedure.
Your Administrator sets up the queue that you access when you press the ACD Key. Contact your
System Administrator for more information.
When you press the ACD Key, the phone prompts you to enter a User ID and Password to login
into the queue. Once logged in, you can make your phone “available” or “unavailable” to take calls
by pressing the Available/Unavailable Key (2). The server monitors your IP phone status. When
you set the IP phone to “available,” the server begins distributing calls to your phone. When you
set the IP phone to “unavailable,” the server temporarily stops distributing calls to your phone.
The LED for the ACD Key shows the current status of your phone.
This LED changes when you log into the phone queue and are available to take calls. The LED
changes again when you are busy with an active call. The table below shows the status of the LED
as they may appear on your IP phone.
Phone
Model
Status: Logged In
Status: Unavailable Logged Out
and Available
6753i
Solid Red LED
Blinking red LED
No LED
Using the ACD Key
Use the following procedure to log into a phone queue from your IP phone.
IP Phone UI
1. Check with your Administrator to verify the queue linked to your ACD Key.
2. Press the ACD Key on your IP phone.
The LCD displays the label of the ACD queue you are accessing.
The "User ID" prompt displays.
ACD: <Queue Label>
User ID:
= Login
= Next
Model 6753i IP Phone User Guide
71
Line Keys and Programmable Keys
ACD LED Table
Line Keys and Programmable Keys
3. Using the keypad, enter your User ID (phone number provided by your System
Administrator) and press the 2 Key.
The "Password" prompt displays.
ACD: <Queue Label>
Password:
= Login
= Next
4. Using your keypad, enter your Password (provided by your System Administrator) and press
the 2 Key.
5. Press 4 (Login) to login to the queue.
You are logged into the queue and the following screen displays.
ACD: <Queue Label>
= Avail
= Logout
6. To allow your phone to be available in the queue, press 2 (Avail).
The following screen displays.
ACD: <Queue Label>
= Unavail
= Logout
If your IP phone status is set to “Available” then the server begins to distribute phone calls
from this queue to your IP phone. You must manually change the state to “Available” in
order to start receiving calls.
7. To temporarily stop receiving calls, press the press 2 (Unavail).
If you are on a call (or miss a call that has been distributed to your phone), your phone status
automatically changes to "Unavailable". Your phone remains in the "Unavailable" state
until one of the following occurs:
•
You use the IP Phone UI to manually switch the IP phone state back to
"Available".
or
•
The availability “timer” for your IP phone expires. This only occurs if your
Administrator has configured an auto-availability timer on your IP phone. Contact your
System Administrator for more information.
8. To logout of the queue, press 4 (Logout).
The server no longer distributes phone calls to your IP phone.
72
Model 6753i IP Phone User Guide
Directed Call Pickup/Group Call Pickup Keys (for Sylantro Servers)
Aastra IP phones support the Directed Call Pickup (DCP) and Group Call Pickup (GCP) features.
The DCP/GCP feature allows you to intercept - or pickup - a call on a monitored extension. You
can configure this feature using the Aastra Web UI to create a DCP or GCP key on the IP phone.
When you configure a DCP key, you specify the extension that you want to monitor. Then, when
the monitored extension receives a call, you press the DCP key to pick up the call. If the monitored
extension receives multiple incoming calls simultaneously, the IP Phone UI displays a list of
incoming calls. You select a call from this list, and are connected to the call.
When you configure a GCP key, you specify the ring group (for example, extensions 2200 - 2210)
that you want to monitor for incoming calls. When an incoming call is received on any of these
extensions, the Operator presses the GCP key and is connected to the call. If multiple incoming
calls are received simultaneously, the Operator press the GCP key, selects an extension from a list,
and presses the Pickup key to answer the call.
Line Keys and Programmable Keys
Note: Your System Administrator must configure the extension range for the
Group Call Pickup feature. Contact your System Administrator for more
information.
Configuring Directed Call Pickup (DCP) Key (for Sylantro Servers)
Use the following procedure to configure Directed Call Pickup using the
Aastra Web UI.
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
Model 6753i IP Phone User Guide
73
Line Keys and Programmable Keys
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the “Type” field, select Directed Call Pickup.
4. In the “Value” field, specify the extension you want to intercept when you press this key.
For example: 2200.
5. In the "Line" field, select the line for which to apply the Directed Call Pickup configuration.
Valid values are 1 through 9.
6. Click
to save your changes.
Configuring Group Call Pickup (GCP) Key (for Sylantro Servers)
Use the following procedure to configure Group Call Pickup using the
Aastra Web UI.
Aastra Web UI
Note: A ring group must be configured on the Sylantro Server in order for a
GCP key to function.
74
Model 6753i IP Phone User Guide
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select a key for which to configure Group Call Pickup.
3. In the “Type” field, select Directed Call Pickup.
Line Keys and Programmable Keys
4. In the “Value” field, enter groupcallpickup.
5. In the "Line" field, select the line for which to apply the Group Call Pickup configuration.
Valid value are 1 through 9.
6. Click
to save your changes.
Using Directed Call Pickup/Group Call Pickup
Use the following procedure for the DCP/GCP feature on your phone.
IP Phone UI
Note: Before using the DCP/GCP feature on your phone, you must first
configure the DCP or GCP Key. You must identify the extension(s) or phone
number(s) you want to monitor when configuring the key. See the previous
procedures to configure a DCP or GCP Key.
Using Directed Call Pickup (DCP)
1. When the monitored extension receives a call, press the DCP Key to pick up the call.
If the monitored extension receives multiple incoming calls simultaneously, the phone
displays a list of incoming calls.
2. Use the 5 and 2 keys to scroll through the list to select an extension.
3. Press 2 (Pickup) Key for the extension you select.
The call is answered.
Model 6753i IP Phone User Guide
75
Line Keys and Programmable Keys
Using Group Call Pickup (GCP)
1. If any of the monitored group of extensions receives a call, press the GCP Key.
The call is answered. If the monitored group of extensions receives multiple incoming calls
simultaneously, the phone displays a list of incoming calls.
2. Use the 5 and 2 keys to scroll through the list to select an extension.
3. Press 2 (Pickup) Key for the extension you select.
The call is answered.
Select an extension
Press the Pickup
Key to answer
the call
76
DCP on line:
1. 2201
= Pickup
= Cancel
Model 6753i IP Phone User Guide
XML Key
The 6753i IP phone has a feature you can enable called "XML" (Extensible Markup Language).
XML is a markup language much like HTML. Your System Administrator can create customized
XML menu services and load them to your IP phone. These services include things like weather
and traffic reports, contact information, company info, stock quotes, or custom call scripts. You
can configure XML using the Aastra Web UI only.
Using the Aastra Web UI, you can configure a key to access XML applications. Under
Operations->Programmable Keys or Operation->Expansion Module, you can assign a key the
type "XML".
Note: The XML services must be set up by your System Administrator before
you can use the key. Contact your System Administrator for more information.
You must also specify an XML URI and a Services label using the following XML fields:
XML Application URI
•
XML Application Title
The XML Application URI is the URI loaded by your phone. The phone performs an HTTP GET.
Contact your System Administrator for the applicable XML URI to enter in the "XML Application
URI" field.
The XML Application Title is the label that displays beside the XML key on your phone. If you
use the Services key to access the XML features, the "XML Application Title" is the label that
displays on the Services Menu in the IP Phone UI.
Note: Contact your System Administrator for the applicable URI to enter in this
field.
After an XML key is configured, you can use the IP Phone UI to access the XML applications.
Model 6753i IP Phone User Guide
77
Line Keys and Programmable Keys
•
Line Keys and Programmable Keys
Configuring an XML Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select XML to apply to the key.
4. In the "Value" field, enter a URI(s) to apply to this key.
Note: Contact your System Administrator for the appropriate value to enter in
the "Value" field.
If you specify multiple URIs in the "Value" field, a list of XML applications appears for
selection after pressing the XML key.
5. In the "XML Application URI" field, enter the XML application URI provided by your
System Administrator.
6. In the "XML Application Title" field, enter the XML application title that you want to
display as the title for the key on your phone.
7. Click
78
to save your changes.
Model 6753i IP Phone User Guide
Accessing the XML Service
After an XML application(s) have been saved to your IP phone, and after a key has been
configured to access the XML application(s), the customized service is ready for you to use.
IP Phone UI
1. Press the key configured for XML on the 6753i phone. A "Custom Features" screen displays
or the title you specified.
2. Use the 5 and 2 to scroll through the customized features.
3. For menu and directory services, select a service to display the information for that customized
service. Message services display to the screen after pressing the key. For user input services,
follow the prompts as appropriate.
4. To exit from the "Customized Features" screen, press the XML key again.
Line Keys and Programmable Keys
Model 6753i IP Phone User Guide
79
Line Keys and Programmable Keys
Sprecode Key
You can set a programmable key or expansion module key to automatically activate specific
services offered by the server. For example, if the sprecode value of *82 is configured, then by
pressing the Sprecode key, *82 automatically activates a service provided by the server. Contact
your System Administrator for information about available services.
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
Configuring a Sprecode Key
Use the following procedure to configure a sprecode key on the 6753i phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select sprecode.
4. In the "Value" field, enter the appropriate value for accessing specific services from the
server.
Note: For values to enter in this field, contact your System Administrator.
5. Click
80
to save your changes.
Model 6753i IP Phone User Guide
Park/Pickup Keys
The 6753i phone has a park and pickup call feature that allows you to park a call and pickup a call
when required.
The IP phones support the Park/Pickup feature on the Asterisk, BroadWorks, Sylantro, and ININ
PBX servers.
You can set programmable keys or expansion module keys on the 6753i to use the park/pickup
feature by setting a programmable key as "Park" or "Pickup”, and then:
•
specify a value
•
specify a line to use
Note: The values you enter for each key are dependent on the type of server you
are using (Asterisk, BroadWorks, Sylantro, or ININ PBX).
•
When a call comes in and you pickup the handset, you can press the applicable "Park" key to
park the call.
•
After the call is parked, you can press the "Pickup" key, followed by the applicable value to
pickup the call.
You configure a Park and Pickup programmable configuration using the Aastra Web UI.
The following table provides the values you enter for the "Park Call" and "Pickup Parked Call"
fields in the Aastra Web UI.
Park/Pickup Call Server Configuration Values
Server
Park Values*
Pickup Values*
Aasterisk
700
700
Sylantro
*98
*99
BroadWorks
*68
*88
ININ PBX
callpark
pickup
*Leave "value" fields blank to disable the park and pickup feature.
Model 6753i IP Phone User Guide
81
Line Keys and Programmable Keys
The park/pickup feature performs as follows:
Line Keys and Programmable Keys
Configuring Park/Pickup Keys
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
Use the following procedure to configure park/pickup on the 6753i phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Park for the first key. For the second key, select Pickup.
4. In the "Value" fields, enter the appropriate values based on the server in your network.
Note: For values to enter in this field, see the table “Park/Pickup Call Server
Configuration Values” on page 81.
5. In the "Line" field, select the lines for which to apply the Park and pickup configuration.
Valid values are 1 through 9.
6. Click
82
to save your changes.
Model 6753i IP Phone User Guide
Using the Park Call/Pickup Parked Call Feature
Use the following procedure on the IP phone to park a call and pick up a parked call.
Park a Call
1. While on a live call, press the "Park" key.
2. Perform the following for your specific server:
For Asterisk Server
Server announces the extension number where the
call has been parked. Once the call is parked, press
the
key to complete parking.
For BroadWorks Server
After you hear the greeting from the CallPark server,
enter the extension where you want to park the call.
For Sylantro Server
For ININ Server
Enter the extension number where you want to park
the call, followed by "#" key.
If the call is parked successfully, the response is either a greeting voice confirming that the call
was parked, or a hang up occurs. The parked call party hears music on hold.
3. If the call fails, you can pick up the call (using the next procedure) and press the "Park" key
again to retry step 2.
Pickup a Parked Call
1. Pick up the handset on the phone.
2. Enter the extension number where the call was parked.
3. Press the "Pickup" key.
If the call pick up is successful, you are connected with the parked call.
Model 6753i IP Phone User Guide
83
Line Keys and Programmable Keys
Enter the extension number where you want to park
the call, followed by "#" key.
Line Keys and Programmable Keys
Last Call Return (lcr) Key (for Sylantro Servers)
Using the Aastra Web UI, you can configure the "Last call return" (lcr) function on a key. This
feature is for Sylantro servers only.
How it works
If you configure "lcr" on a key, and a call comes into your phone, after you are finished with the
call and hang up, you can press the key configured for “lcr” and the phone dials the last call you
received. When you configure an “lcr” key, the label “LCR” displays next to that key on the IP
phone. When the Sylantro server detects an “lcr” request, it translates this request and routes the
call to the last caller.
Configuring a Last Call Return Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Last Call Return.
4. In the "Line" field, select the line to apply this feature.
Valid values are 1 through 9.
5. Click
84
to save your changes.
Model 6753i IP Phone User Guide
Call Forward Key
Using the Aastra Web UI, you can configure the "Call Forward" function on a key. Use call
forwarding when you want a specific account on your phone to be forwarded to another number
when your phone is in the busy state or the no answer state, or both. Pressing the Call Forward key
on the phone accesses the Call Forward Menus. The menus that display are dependant on the Call
Forward mode (Account (default), Phone, or Custom) configured for the phone.
For more information about call forwarding and call forwarding modes, see “Call Forward
Account-Based Configuration” on page 145.
Configuring a Call Forward
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
Line Keys and Programmable Keys
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Call Forward.
4. Click
to save your changes.
Model 6753i IP Phone User Guide
85
Line Keys and Programmable Keys
BLF/Xfer
The BLF key allows one or more extensions to be monitored, and once there is any state change
with those extensions, the key shows the status of the monitored lines. The Xfer key allows a call
to be transferred to other recipients blindly or consultatively. The BLF/Xfer key combines the
BLF and Xfer key's functionality together allowing the user to transfer calls or use BLF with one
key.
Note: It is recommended that you enable the “Switch UI Focus to Ringing Line”
parameter when using the BLF/Xfer feature. For more information about this
parameter, see “Switch UI Focus to Ringing Line” on page 174.
BLF/Xfer Key Requirements and Functionality
•
BLF/Xfer and BLF
A BLF/Xfer key can be configured for subscribing to an extension and monitor the status of
the extension, similar to the BLF key functionality. Changes of the state of the monitored
extension are indicated by a LED / Icon.
•
BLF/Xfer and Blind Transfer Calls
When the focused line is in the “Connected” state, pressing the BLF/Xfer key transfers the
call to the extension unconditionally, disregarding the status of the monitored extension.
If transferring a call to an extension fails, a message “Transfer Failed” displays on the
phone, and you can reconnect the call (get the call back) by pressing the line key again.
86
•
BLF/Xfer and Call Forward
When the focused line is in the “Ringing” state, pressing the BLF/Xfer key forwards the call
to the extension unconditionally, disregarding the status of the monitored extension.
•
BLF/Xfer and Speeddial
When the focused line and the monitored extension are idle, pressing the BLF/Xfer key
causes the phone to go offhook and dial the number of the extension.
Model 6753i IP Phone User Guide
Configuring a BLF/Xfer Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select BLF/Xfer.
4. In the “Value” field, enter the monitored extension or the extension to transfer calls to (for
example, “35”).
5. In the “Line” field, select the line for which you want to use the key functionality.
6. Click
to save your changes.
Model 6753i IP Phone User Guide
87
Line Keys and Programmable Keys
Speeddial/Xfer
The Speeddial key allows a number to be dialed quickly by pressing one key configured for
speeddialing. The Xfer key allows a call to be transferred to other recipients blindly or
consultatively. The Speeddial/Xfer key combines the Speeddial and Xfer key's functionality
together allowing the user to transfer calls or use Speeddial with one key.
Note: It is recommended that you enable the “Switch UI Focus to Ringing Line”
parameter when using the Speeddial/Xfer feature. For more information about
this parameter, see “Switch UI Focus to Ringing Line” on page 174.
Speeddial/Xfer Key Requirements and Functionality
The Speeddial/Xfer key has the following capabilities:
•
Speeddial/Xfer and Speeddial
When the phone is in the “Idle” state, pressing the Speeddial/Xfer key causes the phone to
go offhook and dial the predefined extension.
•
Speeddial/Xfer and Blind Transfer
When the phone is connected to a call, pressing the Speeddial/Xfer key blind transfers the
call to the predefined target.
If transferring a call fails, a message “Transfer Failed” displays, and you can reconnect the
call (get the call back) by pressing the line key again.
•
88
Speeddial/Xfer and Call Forward
When the phone is in the “Ringing” state, pressing the Speeddial/Xfer key forwards the call
to the predefined extension.
Model 6753i IP Phone User Guide
Configuring a Speeddial/Xfer Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Speeddial/Xfer.
4. In the “Value” field, enter the speeddial extension or the extension to transfer calls to (for
example, “5551212”).
5. In the “Line” field, select the line for which you want to use the key functionality.
6. Click
to save your changes.
Model 6753i IP Phone User Guide
89
Line Keys and Programmable Keys
Speeddial/Conf
The 6753i allows you to configure a programmable key or expansion module key to be used as a
speeddial conference key (Speeddial/Conf key) while remaining in the current call. This key
allows a user on a call to conference another party at a pre-defined number while remaining in
the conference.
For example, while on an active call, a user can use the Speeddial/Conf key to dial a recording
service and have the resulting conference recorded.
Note: If not currently in a conference, the Speeddial/Conf key is disabled
on the active call.
If you configure a programmable key as a Speeddial/Conf key and you press this key while on
an active call, the focused line changes to the dialing line. A Cancel softkey displays on the
phone allowing you to abort the conference speeddial if required. The message "Ringing..."
displays below the number when the far end is ringing. The message "Conf. Unavailable" briefly
displays when a conference is already in progress. The active call is not put on hold when the
speeddial number is dialed.
Note: This feature is not compatible with centralized conferencing.
90
Model 6753i IP Phone User Guide
Configuring a Speeddial/Conf Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Speeddial/Conf.
4. In the “Value” field, enter the number or the extension to add to the conference (for example,
“5551212”).
5. In the “Line” field, select the line for which you want to use the key functionality.
6. Click
to save your changes.
Model 6753i IP Phone User Guide
91
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
Line Keys and Programmable Keys
Directory Key
By default, the 6753i has a Directory key configured on Key 3. However, using the Aastra Web
UI, you can assign the Directory key to another available key if required (Key 3 through Key 6).
Directory
Key
The "Directory List" feature allows you to store frequently used names and numbers on the
phone. You can also dial directly from a directory entry.
You can use the Directory key to access a Directory List which contains a customized list of
names with phone numbers and labels.
In addition to creating a Directory key, you can also download a Directory List to your PC if
required using the Aastra Web UI.
Reference
For more information about the Directory List, see “Directory List” on page 124.
92
Model 6753i IP Phone User Guide
Configuring a Directory Key
Aastra Web UI
Notes:
1. Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY by
your System Administrator.
2. By default, the Directory key is Key 3.
Use the following procedure to configure a Directory key on the 6753i phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Directory.
4. Click
to save your changes.
Model 6753i IP Phone User Guide
93
Line Keys and Programmable Keys
Callers List Key
By default, the 6753i has a Callers List key configured on Key 4. However, using the Aastra
Web UI, you can assign the Callers List key to another available key if required (Key 3 through
Key 6).
Callers List
Key
The Callers list is a stored log of your incoming calls. You can use the Callers List key to access
a list of callers that called your phone.
Reference
For more information about the Callers List, see “Callers List” on page 134.
Configuring a Callers List Key
Aastra Web UI
Notes:
1. Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY by
your System Administrator.
2. By default, the Callers List key is Key 4.
Use the following procedure to configure a Callers List key on the 6753i phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
94
Model 6753i IP Phone User Guide
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Callers List.
4. Click
to save your changes.
Line Keys and Programmable Keys
Model 6753i IP Phone User Guide
95
Line Keys and Programmable Keys
Transfer Key
By default, the 6753i has a Transfer key configured on Key 5. However, using the Aastra Web
UI, you can assign the Transfer key to another available key if required (Key 3 through Key 6).
Transfer
Key
The Transfer key allows you to perform blind or consultative call transfers to other recipients.
The blind transfer feature transfers a call to another number without you having to talk to the
recipient. A consultative transfer feature transfers a call to another number but allows you to
speak with the recipient before the call is actually transferred.
Reference
For more information about using blind and consultative call transfers, see “Transferring Calls”
on page 116.
96
Model 6753i IP Phone User Guide
Configuring a Transfer Key
Aastra Web UI
Notes:
1. Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY by
your System Administrator.
2. By default, the Transfer key is Key 5.
Use the following procedure to configure a Transfer key on the 6753i phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Transfer.
4. Click
to save your changes.
Model 6753i IP Phone User Guide
97
Line Keys and Programmable Keys
Conference Key
By default, the 6753i has a Conference key configured on Key 6. However, using the Aastra
Web UI, you can assign the Conference key to another available key if required (Key 3 through
Key 6).
Conference
Key
The Conference key allows you to link three active calls into a single conference (Local
Conferencing). This key also helps to create multiple conferences with unlimited participants on
your phone if your System Administrator has enabled Centralized Conferencing on your phone.
Reference
For more information about Local and Centralized Conferencing, see “Conferencing Calls” on
page 118.
Configuring a Conference Key
Aastra Web UI
Notes:
1. Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY by
your System Administrator.
2. By default, the Conference key is Key 6.
Use the following procedure to configure a Conference key on the 6753i phone.
98
Model 6753i IP Phone User Guide
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
Line Keys and Programmable Keys
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Conference.
4. Click
to save your changes.
Model 6753i IP Phone User Guide
99
Line Keys and Programmable Keys
Intercom Key
By default, the IP phone allows incoming intercom calls to be automatically answered without
having to set up an Icom key on your phone. For more information about changing the behavior
of incoming Intercom calls, see the section “Incoming Intercom Call Features” on page 181.
Your System Administrator can enable outgoing intercom calls on your phone. If enabled, you
must configure an Icom key on your phone to use for outgoing intercom calls.You must
configure a programmable key or expansion module key with the function, “Intercom”.
Use the following procedure to configure a key as an Icom key using the Aastra Web UI.
Configuring an Intercom Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Intercom.
4. Click
100
to save your changes.
Model 6753i IP Phone User Guide
Using the Icom Key (for Outgoing Intercom Calls)
IP Phone UI
1. Press the Icom key.
2. Enter the extension number of the person you want to intercom or the BLF key for that
extension.
3. After a beep tone, your phone automatically connects with the remote extension and you can
speak through its speaker.
4. To cancel intercom, press
or hang up the handset.
5. When you are finished speaking, hang up the phone by placing the handset back on-hook or by
pressing
or the line/call appearance button for the active call. When you hang up, the
remote phone also hangs up.
Reference
Model 6753i IP Phone User Guide
101
Line Keys and Programmable Keys
For more information about incoming intercom calls, see “Incoming Intercom Call Features” on
page 181. For more information about outgoing intercom calls, see “Available Features Enabled
by Administrators” on page 190.
Line Keys and Programmable Keys
Services Key
The 6753i allows you to configure a Services key that, when pressed on the phone, displays the
Services menu which includes the following options:
•
Directory (See “Directory List” on page 124 for more information.)
•
Callers List (See “Callers List” on page 134 for more information.)
•
Voicemail (See “Voicemail” on page 161 for more information.)
The Services Menu can also be accessed via the IP Phone UI at the location, Options->Services.
The Services key can also access any XML applications setup by your System Administrator.
Contract your System Administrator for more information.
To configure a Services key, you must configure a key with the function, “Services”.
Use the following procedure to configure a key as a Services key using the Aastra Web UI.
Configuring a Services Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Services.
4. Click
102
to save your changes.
Model 6753i IP Phone User Guide
Using the Services Key
IP Phone UI
1. Press the Services key. The following default list displays:
•
Directory (See “Directory List” on page 124 for more information.)
•
Callers List (See “Callers List” on page 134 for more information.)
•
Voicemail (See “Voicemail” on page 161 for more information.)
Note: Addtional options may display in the Services Menu if setup by your
System Administrator. Contact your Administrator for more information.
2. Select an option from the Services Menu.
3. To cancel a Service, press
.
Line Keys and Programmable Keys
Model 6753i IP Phone User Guide
103
Line Keys and Programmable Keys
Phone Lock Key
You can configure a programmable key or an expansion module key on the phone to use as a
lock/unlock key. You assign the function of the key as “Phone Lock”.
Use the following procedure to configure a key as a lock/unlock key in the Aastra Web UI.
Configuring a Phone Lock Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Phone Lock.
4. Click
to save your changes.
Note: You can lock/unlock the phone using the new key you just configured,
using the Aastra Web UI at the path Operation->PhoneLock, or using the "Phone
Lock" option on the IP Phone UI at the path Options->Phone Lock. For more
information about using the lock/unlock feature, see “Phone Lock” on page 44.
104
Model 6753i IP Phone User Guide
Using the Lock/Unlock Key on the IP Phone
After configuring a key as a lock/unlock key, refer to the following procedure to use the key on the
IP phone.
IP Phone UI
Lock the Phone
1. Press the Lock key.
The phone locks.
The LED for the key AND the Message Waiting Lamp illuminate steady ON. An “Unlock”
label appears next to the key you just pressed.
Unlock the Phone
1. Press the Unlock key.
A password prompt displays.
Model 6753i IP Phone User Guide
105
Line Keys and Programmable Keys
2. Enter your user password and press ENTER.
The phone unlocks.
The LED for the key AND the Message Waiting Lamp go OFF. The “Lock” label appears next
to the key you just pressed.
Line Keys and Programmable Keys
Paging Key (Sends the RTP Stream)
You can configure a Paging key on the phone that allows you to send a Real Time Transport
Protocol (RTP) stream to pre-configured multicast address(es) without involving SIP signaling.
You enter a multicast IP address(es) and a port number for the Paging key, that when pressed,
initiates an outgoing multicast RTP session. This is called Group Paging on the IP phones.
You can also specify group paging RTP addresses that the phone listens for when receiving RTP
streams. You can specify up to 5 listening multicast addresses at the path, Basic
Settings->Preferences->Group Paging RTP Settings.
For more information about Group Paging and how it works, and to specify multicast addresses,
see “Group RTP Paging (receives RTP streams)” on page 184.
Configuring a Paging Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select Paging.
106
Model 6753i IP Phone User Guide
4. In the “Value” field, enter a multicast IP address and a port number for the Paging key. When
you press this key, the phone initiates an outgoing multicast RTP session to the specified
address using the specified port. (For example, 239.0.1.15:10000).
Note: The “Value” field allows for one multicast address entry only.
5. To receive RTP steams for Group Paging, you must also configure the "Paging Listen
Addresses" parameter at the path, Basic Settings->Preferences->Group Paging RTP Settings.
For more information about setting this parameter, see “Group RTP Paging (receives RTP
streams)” on page 184.
6. Click
to save your changes
Using the Paging Key
The following procedure describes the use of the Paging key on the IP Phone. The procedure
assumes you have already configured the Paging key using the Aastra Web UI.
Notes:
1. Recipient of a Paging call can set a global “Do Not Disturb” (DND) to ignore
any incoming pages.
2. For incoming Paging, the phone uses the Intercom configuration settings. The
incoming Page is dependant on the “Allow Barge-In” parameter setting and the
“Idling/On Call” state.
1. On the IP Phone, press the key you configured for Paging.
The phone opens a multicast RTP session and an outgoing OR incoming phone screen displays
as follows:
Paging
00:01
= Drop
2. Press the Drop key to end the multicast RTP session and return to the idle screen.
Note: If you enable global DND on the phone, the incoming multicast RTP
session is dropped.
Model 6753i IP Phone User Guide
107
Line Keys and Programmable Keys
IP Phone UI
None Key
You can set a key to force a blank entry on the IP phone display for a specific key. You do this by
setting the key to "none". If a particular key is not defined, it is ignored.
Setting a None Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable ONLY
by your System Administrator.
Use the following procedure to configure a None key on the 6753i IP Phone.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select None.
4. Click
to save your changes.
Deleting a Key
Aastra Web UI
Note: Keys 1 and 2 (SAVE and DELETE keys) can be made configurable
ONLY by your System Administrator.
Use the following procedure to delete a key function using the Aastra Web UI.
1. Click on Operation->Programmable Keys.
or
Click on Operation->Expansion Module <N>.
Line Keys and Programmable Keys
Programmable Keys and Expansion Module Keys
2. Select from "Key 3" through "Key 6".
or
Select from “Key 1” through “Key 36” (M670i).
3. In the "Type" field, select None.
4. Click
to save your changes
The function is deleted from the IP phone memory.
Model 6753i IP Phone User Guide
109
Making Calls
Making Calls
This section describes ways to make calls on your 6753i phone, using your handset,
speakerphone or headset.
Dialing a Number
First, take the phone off-hook by:
•
lifting the handset
•
pressing
•
pressing a line/call appearance button.
or
At the dial tone, enter the number you wish to call.
Note: After dialing the number, the phone has a short delay before sending the
call. To send the call immediately, you can press the "#" key immediately after
dialing the number. The phone sends the call without delay.
If you are unable to make calls within certain area codes, check with your System Administrator
for any toll restrictions placed on your extension that may restrict your access to long distance
area codes or dialing prefixes.
=Dial
When your party picks up, a timer appears on your display that records the length of your call.
If the Live DialPad option is on, as soon as you press the first digit on the dial pad the phone
automatically selects the next available line, go off-hook and dial as digits are pressed.
Using Handsfree Speakerphone
The handsfree feature allows you to speak to someone without using the handset or headset.
Your phone must be in either the Speaker or Speaker/Headset audio mode. For more information
about setting the audio mode on your phone, see “Set Audio” on page 27.
IP Phone UI
110
•
To dial using handsfree, first press
and enter a number at the dial tone.
•
To answer a call on your phone using handsfree, press
button.
or the line/call appearance
Model 6753i IP Phone User Guide
•
If you are in Speaker audio mode, lift the handset and press
handsfree and handset.
•
If you are in Speaker/headset audio mode, press
headset.
•
When the handset is on hook, press
to switch between
to switch between handsfree and
to disconnect the call.
When handsfree is on, the speaker light turns on.
Using a Headset
The 6753i accepts headsets through the modular RJ9 jack on the back of the phone. Contact your
telephone equipment retailer or distributor to purchase a compatible headset.
Note: Customers should read and observe all safety recommendations contained
in headset operating guides when using any headset.
Advanced Volume Controls for the Headset Mic
On the 6753i, there are 3 options for the headset microphone volume. For more information about
the headset microphone, see “Headset Mic Volume” on page 27.
IP Phone UI
To change the volume:
1. Press
to enter the Options list.
2. Select Preferences and press 4.
3. Use 2 to scroll down to Set Audio and press 4 to select.
4. Press 2 to scroll down to Headset/Mic Volume and press 4 to select.
5. Use 2 to scroll down the list and press 4 to select your desired volume.
6. Press 4 to save changes and 3 to exit.
7. If you do not wish to save changes, press 3 to return to the previous screen.
Making Calls
Note: By default, the volume for the headset microphone is set to medium.
Model 6753i IP Phone User Guide
111
Making Calls
Making and Receiving Calls Using a Headset
IP Phone UI
1. Ensure that you have selected a headset audio mode by accessing the Options list (under
option Preferences->Set Audio->Audio Mode on the IP Phone).
2. Plug the headset into the jack.
3. Press the
key to obtain a dial tone or to answer an incoming call. Depending on the
audio mode selected from the options menu, a dial tone or an incoming call is received on
either the headset or the handsfree speakerphone.
4. Press the
key to end the call.
Redial
IP Phone UI
•
Press
to dial the most recent number you dialed from the phone.
•
If you are off-hook and press
the last number you called is called back.
•
If you are on-hook and press
, a Redial Directory list appears on-screen.
The redial list is available during active calls. It stores up to the last 100 numbers you called,
allowing you to scroll through and select the number you wish to redial.
Note: Your System Administrator can set your Redial key to speeddial a specific
number. Contact your System Administrator for more information.
Accessing the Redial List
IP Phone UI
1. If you are off-hook and press
called.
, the telephone automatically dials the last number you
2. If you are not on the phone, press
to display the most recently dialed number and use
2 and 5 to scroll through the list to view the other numbers.
3. Press 2 to see the second most recently dialed number, or 5 to see the oldest call on your
list.
4. To dial the displayed number press
5. Press
or the
, or lift the Handset or press any line keys.
key to cancel.
Note: The redial list is available during active calls. It also stores up to the last
100 numbers you called, allowing you to scroll through and select the number
you wish to redial.
112
Model 6753i IP Phone User Guide
Deleting from the Redial List
Note: You cannot delete individual entries in the Redial List.
IP Phone UI
Delete All Items
1. Press
.
2. Press the Delete Key, then press the Delete Key again at the prompt to erase all items.
DELETE again to
erase all items
Redial List is
empty
Mute
You can use the Mute
key to mute the handset, headset, or speakerphone. When you use the
mute key on your phone, you cannot be heard on an active call or on a conference.
When a call is muted, the icon displays as follows.
1
John Burns
9054550055
03:00
For muted calls, the handsfree LED flashes and the Mute key LED is ON.
Press the
button at any time to mute handset, headset, or handsfree.
The speaker light flashes slowly and you can hear the caller, but they cannot hear you. To switch
mute on or off, press
.
Note: If you place a muted call on hold, the phone automatically takes the call
off mute when you reconnect to the call.
Model 6753i IP Phone User Guide
113
Making Calls
IP Phone UI
Receiving Calls
Receiving Calls
When a call is ringing at your extension, you see the "Inbound Call" Screen. The line/call
appearance light flashes quickly for the incoming call.
Laflamme & Assoc
555-1234
Answering an Incoming Call
IP Phone UI
To answer the call
•
For handsfree operation, press
call.
•
Press
or the line/call appearance button for the incoming
for handsfree or headset operation.
Note: The audio mode setting you have selected in the options list under Set
Audio->Audio Mode determines if the call goes to handsfree or headset operation.
For more information, see “Set Audio” on page 27.
•
Lift the handset for handset operation.
If the phone is already connected to a call, pressing the line/call appearance button for the new
incoming call automatically places the connected call on hold and answers the new call. To
reconnect to a party, press the line/call appearance button for that call.
If you cannot answer the call, the caller goes to voicemail has been configured for your
extension.
Note: The
button can be used to cancel the call pickup procedure.
Sending an Incoming Call to Voicemail
You can send an incoming call directly to voicemail without answering the call. To do this, press
without picking up the handset. If you're already on the phone your incoming call should
go directly to voicemail. Your phone screen displays a voicemail icon (
) along with the
number of waiting messages, if you have unheard messages
(example:
x4).
114
Model 6753i IP Phone User Guide
Handling Calls
When you are connected to a call, you can use the hard keys or programmable keys on the phone
to place a call on hold, transfer a call, or conference.
Placing a Call on Hold
You can place an active call on hold by pressing the Hold
hold, only your phone can retrieve the call.
key. When you place a call on
When a call is on hold, the icon displays on-hook as follows.
1
Call held
03:05
For on-hold calls, the timer displays as running and the Line and main LEDs flash.
IP Phone UI
To place a call on hold
1. Connect to the call (if not already connected).
2. Press the Hold
key.
Call held
Jun 8 2:55pm
Note: If you are connected to another call, the phone does not beep to remind
you that you still have a call on hold.
Model 6753i IP Phone User Guide
115
Handling Calls
The line/call appearance light begins to flash slowly and after a short time the phone beeps softly
to remind you that you still have a call on hold. The screen displays "Call Held" with the line
number the call is held at the phone.
Handling Calls
When on Hold
To let your caller know that they are still on hold, music plays softly (if this has been set up for
your system). The call/line appearance light for the line you are on remains solid to indicate that
you are still connected.
John 1051
01:17
Automatic Hold
When juggling between calls, you do not have to press the hold button to go from one call to the
next. The phone automatically puts your current call on hold as soon as you press a new line/call
appearance button. If you have more than one call on hold, you can reconnect to a held call by
pressing the line/call appearance button where that call is being held. Press
to disconnect
the call.
Retrieving a Held Call
If you have more than 1 call on hold, you can scroll through the held call information by
pressing 3 and 4 navigation keys. To reconnect to a call press the line/call appearance button
where that call is being held. If you press the call/line appearance button again, you disconnect
from the call.
Transferring Calls
Blind Transfer
A blind transfer is when you transfer a call directly to another extension without consulting with
the person receiving the call. To do this, simply complete the transfer immediately after you
have entered the number. The call goes directly to the extension or outside line you transferred
to. If the party you are transferring the call to does not answer, the transferred call rings back to
your extension.
Consultive Transfer
You also have the option to consult with the person you are transferring the call to, before you
complete the transfer. To do this, remain on the line until the receiving party answers the call.
After consulting with the receiving party, you can either complete the transfer or cancel the
transfer to go back to the original call.
116
Model 6753i IP Phone User Guide
IP Phone UI
Use the following procedure to transfer a call to another extension. Use the following illustration
as a reference.
Transfer
Key
1. Connect to Party 1 (if not already connected). Party 1 is the party you want to transfer.
2. Press the Transfer Key. You should hear a dial tone as a second line opens up.
3. Dial the extension number (or the outside number) to Party 2. This is the Party for which you
want to transfer Party 1.
4. To complete a "blind" transfer, press the Transfer Key again before the receiving end answers.
To complete a consultive transfer, remain on the line to speak with the Party 2, before pressing
the Transfer Key again to transfer Party 1 to Party 2. To cancel the transfer, select Cancel on
the display screen.
Transferring Two Existing Calls
The 6753i allows you to perform a transfer of a call when there are currently two active calls on
the phone. For example, on your phone, there are two active calls - Call A and Call B. Call B is on
hold. You can perform the following to transfer Call A to Call B:
Press Xfer key. A new line opens.
2.
Press or scroll to the Line where Call B is on hold.
3.
Press Xfer key.
Handling Calls
1.
Call A is transferred to Call B.
Model 6753i IP Phone User Guide
117
Handling Calls
Conferencing Calls
The 6753i IP phone offers two methods of conferencing:
•
Local conferencing (default method).
•
Centralized conferencing (for Sylantro and Broadsoft Servers) (Administrator must enable
this method).
By default, the Conference key is Key 6 on your phone. A Conference key must be set up on
your phone before you can set up conference calls. To assign a key as a Conference key, see
“Conference Key” on page 98.
Conference State Screens
When you use the Conference key to initiate a conference call, the following screen displays.
1-1
1-2
John
Jim
03:05
= Drop
In a conference call, the call timer moves to the left. You use the up and down arrow keys to
scroll to a party on the list. You use the right arrow key to select the party to drop.
Local Conferencing
The 6753i phone supports up to 3 parties (including yourself) in a conference call. This is called
Local Conferencing and is the default method of conferencing on the 6753i.
Note: Your System Administrator can set your Conference key to speeddial a
specific number. Contact your System Administrator for more information.
118
Model 6753i IP Phone User Guide
Using Local Conferencing
IP Phone UI
Use the following procedure to create a conference call using local conferencing. Use the
following illustration as a reference.
Conference
Key
1. When you begin a conference, you are the first party in the conference (Party 1). Pickup the
handset or press the speakerphone key.
A line opens up.
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them before adding
them to the conference.
4. Press the Conf Key. A new line opens.
2
=Dial
5. Enter the phone number of Party 3.
7. Press the Conf key again to add Party 3 to the conference. Party 1 (which is yourself), Party 2,
and Party 3 are all connected to a single conference.
8. To drop a party from the conference, press the Conf key once more.
Note: You can use 2 and 5 to scroll through and see the numbers and names (if
available) of the parties in the conference call. When a name is displayed,
pressing 4 drops the displayed party from the call.
Model 6753i IP Phone User Guide
119
Handling Calls
6. Wait for Party 3 to answer. When Party 3 answers, you can consult with them before adding
them to the conference.
Handling Calls
Joining Two Active Calls in a Single Conference
IP Phone UI
1. Begin with active calls on two different lines (for example, Line 1 and Line 2 have active
calls).
2. Press the Line key for which you want to conference the two calls together (for example,
Line 1).
3. Press the Conf key.
4. Press the Line key that has the second active call (for example, Line 2).
5. Press the Conf key. The two active calls link into a conference call on Line 1.
Note: You can use 2 and 5 to scroll through and see the numbers and names (if
available) of the parties in the conference call. When a name is displayed,
pressing 4 drops the displayed party from the call.
Centralized Conferencing (for Sylantro and Broadsoft Servers)
The 6753i allows you to create multiple conferences with unlimited participants (depending on
your server limitations) when your Administrator enables Centralized Conferencing.
If your Administrator does not enable Centralized Conferencing, then the 6753i uses Local
Conferencing by default.
Your Administrator can configure Centralized Conferencing globally on all lines or on specific
lines. Although, for the global setting to work, you must configure the lines with the applicable
phone number.
Reference
For more information on Centralized Conferencing, see “Centralized Conferencing” on
page 192 or contact your System Administrator.
120
Model 6753i IP Phone User Guide
Using Centralized Conferencing
IP Phone UI
Note: When Centralized Conferencing is enabled on your phone, local
conferencing (or three-way conferencing) works as indicated in the previous
section, “Using Local Conferencing.” Joining two active calls in a conference
also works as indicated in the previous section, “Joining Two Active Calls in a
Single Conference.”
Use the following procedure to create a conference call using centralized conferencing. Use the
following illustration as a reference.
Conference
Key
Setting Up a Conference and Adding Multiple Parties
(for Sylantro and Broadsoft Servers)
Note: You can have an unlimited number of parties in a conference (dependent
on the limitations of the server.
1. When you begin a conference, you are the first party in the conference (Party 1). Pickup the
handset or press the Speakerphone Key.
A line opens up.
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them before adding
them to Conference 1.
4. Press the Conf Key. A new line opens.
2
=Dial
5. Enter the phone number of Party 3.
Model 6753i IP Phone User Guide
121
Handling Calls
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
Handling Calls
6. Wait for Party 3 to answer. When Party 3 answers, you can consult with them before adding
them to the Conference 1.
7. Press the Conf Key again to add Party 3 to Conference 1. Party 1 (which is yourself), Party
2, and Party 3 are all connected to Conference 1.
8. Press an available Line Key (or answer an incoming call on an available line). If calling out,
call Party 4.
9. Wait for Party 4 to answer. When Party 4 answers, you can consult with them before adding
them to the conference.
10. Press the Conf Key to add Party 4 to Conference 1.
11. Press the Line Key that has Conference 1.
12. Press the Conf Key to join all parties (Parties 1 through 4) on Conference 1.
13. To add more parties, repeat steps 8 through 12.
Note: You can use 2 and 5 to scroll through and see the numbers and names (if
available) of the parties in the conference call. When a name is displayed,
pressing 4 drops the displayed party from the call.
If any party in the conference hangs up (including the party that began the conference), all other
parties in the conference are still connected.
Setting Up Multiple Conferences (for Sylantro Server only)
Note: The 6753i is limited to 9 conferences (a single conference each on lines 1
through 9).
1. Start Conference 1 using the procedures in the previous section, “Setting Up a Conference
and Adding Multiple Parties (for Sylantro and Broadsoft Servers)”.
2. When you are finished adding all required parties to Conference 1, press an available Line
Key to start Conference 2. You are Party 1 on Conference 2. Call Party 2.
3. When Party 2 answers, press the Conf Key.
4. Press an available Line Key.
5. Call Party 3 for Conference 2.
6. When Party 3 answers, press the Conf Key to join Parties 1 (which is yourself), Party 2, and
Party 3 on Conference 2.
You now have two active conferences on two different lines.
Note: When you are connected to multiple conference calls, and you put a
conference on hold, the conference may be on hold for a limited period of time
before it is disconnected. Contact your System Administrator for more
information.
If any party in a conference hangs up (including the party that began the conference), all other
parties in the conference are still connected.
122
Model 6753i IP Phone User Guide
Joining Additional Parties to Active Conferences
In centralized conferencing, you can join multiple incoming or outgoing calls to active
conferences. Before following this procedure, at least one active conference must exist on your
phone.
1. As Party 1, pickup the handset or press the speakerphone key.
A line opens up.
2. Call Party 2 by dialing their number (or answer an incoming call of a Party).
3. Wait for Party 2 to answer. When Party 2 answers, you can consult with them before adding
them to the conference.
4. Press the Conf Key.
5. Press the Line Key that has the active conference. (For example, Line 1 and Line 2 both have
active conferences. Pressing Line 1 joins Party 1 and Party 2 to the conference on Line 1.
Pressing Line 2 joins Party 1 and Party 2 to the conference on Line 2.)
6. Press the Conf Key again to join the Parties to the active conference.
Ending a Conference and Transferring Remaining Parties
The 6753i allows a Host to drop from a 3-way conference and let the other two parties remain
connected by pressing a Xfer key.
Notes:
1. The 6753i does not support scrolling between lines.
2. The Caller ID of the dropped Host still displays on the remaining parties’ phones.
If you are the Host of a conference and want to leave that conference:
•
While in a 3-way conference press the Xfer
key on the phone.
Your phone leaves the 3-way conference but the remaining parties are still connected to the
conference.
Ending Calls
To end a call, you first need to connect or reconnect to the call if not already connected (for example, if
your caller is on hold). Press
or the line/call appearance button of the active call to end the
call. If connected through the handset, you can also place the handset back on hook to end the call.
Model 6753i IP Phone User Guide
123
Handling Calls
IP Phone UI
Managing Calls
Managing Calls
The 6753i has several features that make it easier to manage calls, and to keep track of your
caller history, as well as your business and personal contacts.
These features include:
•
Directory List
•
Callers List
•
Call Forwarding
•
Missed Calls Indicator
•
Voicemail
Directory List
The Directory List is your personal phone book, conveniently stored within your phone. You can
enter up to 200 entries into the 6753i Directory by adding them manually, or by saving the
number and name from other lists stored on your phone. You can also dial directly from a
directory entry. Each entry can contain a maximum of 16 letters and numbers. On the 6753i, you
access the Directory by pressing the Directory Key (Key 3).
Accessing Your Directory
IP Phone UI
Use the following procedure to access your Directory List. Use the following illustration as a
reference.
Directory
Key (Key 3)
1. Press the Directory Key (Key 3). The directory displays the number of entries in your list. If
the Directory list is empty, "Directory Empty/Use Save to add" is displayed.
Directory empty
Use Save to add
124
Model 6753i IP Phone User Guide
2. You can access entries by pressing 2 and 5 to scroll through the list.
3. To search for an entry by name, press the dial pad number corresponding to the first letter of
the name (for example, press 7 for the letter P). Continue to press the dial pad number to
access other letters on the same key (for example, press 7 three times for ‘Ron’). If there are
multiple entries under the same letter, you can use 2 and 5 to scroll through the list, or
continue to press the next letters of the name to find a better match.
4. To dial the displayed number press
or just lift the handset or press any Line Key.
5. Press the Directory Key to cancel.
Sorting Entries and Quick Search Feature
You can also sort multiple numbers according to preference and perform a quick-search feature
that allows you to enter the first letter that corresponds to a name in the Directory to find specific
line items. The phone displays the first name with this letter.
Note: The quick-search feature in the Directory List works only when the
Directory is first accessed.
Managing the Directory List
From the Directory List in the IP Phone UI, you can perform the following:
•
“Add a New Entry to the Directory List” (page 126)
•
“Edit an Entry in the Directory List” (page 128)
•
“Delete an Entry from the Directory List” (page 129)
•
“Save an Entry to the Directory List” (page 130)
Managing Calls
Model 6753i IP Phone User Guide
125
Managing Calls
Add a New Entry to the Directory List
IP Phone UI
Use the following procedures to add a new entry to the Directory List. Use the following
illustration as a reference.
Save Key
Delete Key
Directory
Key
Notes:
1. Use the 3 Key when required for backspacing.
2. You can exit the entry process any time by pressing the
Key.
1. Press the Directory Key (Key 3).
2. Press Save (Key 1).
The "Enter Number" prompt displays.
3. Enter a phone number using the numbers on the keypad and press Save. To backspace and
erase a mistake, press 3 or press the Delete Key (Key 2).
The "Press 1st letter to enter name" prompt displays.
4. Enter a name to associate with the phone number you just entered, and press Save. Use the
keypad to select the letters. Continue to press the number key to access the next letter for
that key (for example, press 2 three times to access C). Press 4 to move to the next space, or
wait a moment and the cursor automatically advances. To insert a space between letters,
press 4. To backspace and erase a mistake, press 3 or press the Delete Key.
The "Line" prompt displays. The default is Line 1.
5. If you want to save the new Directory entry to use Line 1, press Save to save the new entry
to the Directory List.
If you want the new entry to use a different line, use the 2 key to select a different Line and
press Save.
The new entry you added is saved to the Directory List.
Saved: Directory
John Burns
126
Model 6753i IP Phone User Guide
Adding an Entry to the Directory List from the Save Key
You can also add a new entry to the Directory List from the Save Key (Key 1).
Notes:
1. Use the 3 Key when required for backspacing.
2. You can exit the entry process any time by pressing the
Directory Key.
Key or the
1. Press the Save Key.
The "Save to?" prompt displays.
2. Press the Directory Key.
The "Enter Number" prompt displays.
3. Enter a phone number using the numbers on the keypad and press Save. To backspace and
erase a mistake, press 3 or press the Delete Key (Key 2).
The "Press 1st letter to enter name" prompt displays.
4. Enter a name to associate with the phone number you just entered, and press Save. Use the
keypad to select the letters. Continue to press the number key to access the next letter for that
key (for example, press 2 three times to access C). Press 4 to move to the next space, or wait
a moment and the cursor automatically advances. To insert a space between letters, press 4.
To backspace and erase a mistake, press 3 or press the Delete Key.
The "Line" prompt displays. The default is Line 1.
5. If you want to save the new Directory entry to use Line 1, press Save to save the new entry to
the Directory List.
If you want the new entry to use a different line, use the 2 key to select a different Line and
press Save.
The new entry you added is saved to the Directory List.
Saved: Directory
John Burns
Managing Calls
Model 6753i IP Phone User Guide
127
Managing Calls
Edit an Entry in the Directory List
IP Phone UI
Use the following procedure to edit an entry in the Directory List. Use the following illustration
as a reference.
Save Key
Directory
Key
1. Press the Directory Key.
2. Access the entry you want to edit by pressing the first letter of the name on the dial pad, or
use 2 and 5 to scroll through the list to find the name.
3. To begin editing, press 3. Press 3 again to erase the numbers or letters to the left or use the
dial pad to enter additional digits or characters once you have saved the number.
If you don't want to change the number or name just press the Directory Key or the
Key at any time to exit.
4. Press the Save Key to finish.
128
Model 6753i IP Phone User Guide
Delete an Entry from the Directory List
You can delete a single entry from the Directory List, or you can delete all entries from the
Directory List.
IP Phone UI
Use the following procedures to delete a single entry or all entries from the Directory List. Use the
following illustration as a reference.
Delete Key
Directory
Key
Delete a Single Entry
1. Press the Directory Key.
2. Press 2 and 5 to find the entry you want to delete.
3. Press the Delete Key.
The "DELETE again to erase this item" prompt displays.
DELETE again to
erase this item
Managing Calls
4. Press the Delete Key again at the prompt to erase the entry.
Delete All Entries
1. Press the Directory Key.
2. Press the Delete Key.
The "DELETE again to erase all items" prompt displays.
DELETE again to
erase all items
Model 6753i IP Phone User Guide
129
Managing Calls
3. Press the Delete Key again to erase all entries from the Directory List.
The "Directory empty" prompt displays.
Directory empty
Use Save to add
Save an Entry to the Directory List
You can save entries (names and numbers) from other sources to your Directory using any of the
following methods:
•
Saving from the Display
•
Saving from the Caller List
•
Saving from the Redial List
Saving from the Display
IP Phone UI
You can save the name and/or number displayed on your screen during a call to the Directory
List, or to one of your programmable keys using the following procedure. Use the following
illustration as a reference.
Save Key
Directory
Key
1. Press the Save Key during the call.
Save to?
John Burns
9054550055
2. Press the Directory Key or an empty programmable key. If a name is displayed both the
number and name are saved in the Directory List or the programmable key. If no name or
"Unknown Name" displays, you can enter the name using the dial pad.
3. Press the Save Key to finish.
130
Model 6753i IP Phone User Guide
Saving from the Callers List
IP Phone UI
Use the following procedure to save names/numbers from the Callers List to the Directory. Use the
following illustration as a reference.
Save Key
Directory
Key
Callers List
Key
1. Press the Callers List Key (Key 4).
2. From the Callers List, scroll through the list to find the name and number that you want to save
to your Directory.
3. Press the Save Key.
4. Press the Directory Key to save the number you selected to the Directory List. If the name is
displayed with the number, both are saved to the Directory. If no name is displayed, you can
enter the name using the dial pad.
Managing Calls
Model 6753i IP Phone User Guide
131
Managing Calls
Saving from the Redial List
IP Phone UI
Use the following procedure to save names/numbers from the Redial List to the Directory. Use
the following illustration as a reference.
Save Key
Directory
Key
Redial List
Key
1. Press the Redial List Key (
).
2. From the Redial List, scroll through the list to find the name and number that you want to
save to your directory.
3. Press the Save Key.
4. Press the Directory Key to save the number you selected to the Directory List. If the name is
displayed with the number, both are saved to the Directory. If no name is displayed, you can
enter the name using the dial pad.
132
Model 6753i IP Phone User Guide
Downloading the Directory List to Your PC
You can download the Directory List to your PC via the Aastra Web UI. The phone stores the
directorylist.csv file to your PC in comma-separated value (CSV) format.
You can use any spreadsheet application to open the file for viewing. The following is an example
of a Directory List in a spreadsheet application. The file displays the name, phone number, and line
number for each Directory entry.
Note: Your System Administrator can populate your IP phone Directory List
with server directory files. Contact your System Administrator for more details.
Download the Directory List
Use the following procedure to download the Directory List to your PC using the Aastra Web UI.
Aastra Web UI
1. Click on Operation->Directory.
.
3. Click OK.
4. Enter the location on your computer where you want to download the Directory List and click
SAVE.
The callerslist.csv file downloads to your computer.
5. Use a spreadsheet application to open and view the Directory List.
Model 6753i IP Phone User Guide
133
Managing Calls
2. In the Directory List field, click on
A File Download message displays.
Managing Calls
Callers List
The Callers list is a stored log of your incoming calls. The 6753i IP Phone stores information for
up to 200 incoming calls in the Callers list.
By default, the Callers List Key is Key 4 on the top left of your phone.
Callers List Key
Note: Your System Administrator can create a custom Callers List XML
application allowing you to access the Callers List via an XML Key instead of the
Callers List Key. This allows you to configure the Callers List Key with other
functions if required. Contact your System Administrator for more information.
Your phone logs the number and name (if available) of the caller, when they last called, and the
number of times they tried to reach you. When the Callers list is full, the oldest call records are
deleted to accommodate the information of new callers.
If the phone number of an incoming or outgoing call matches a number that you have
programmed with a name in a programmable key or in the Directory List, the Callers List
displays the name and number.
The display shows you how many callers have been added to the list since you last checked it.
134
Model 6753i IP Phone User Guide
Caller’s List Screen Display
Display Item
Description
450-349-0438
Indicates you have returned the call from the
Callers list.
N MAR 04 3:30pm 2x
"N" indicates a new call.
XX New Callers
When you’re not on the telephone and not in the
Callers list, the display shows you how many
callers have been added to the list since you last
checked it.
Indicates an unanswered call in the Callers list.
Indicates an answered call in the Callers list.
Indicates a Call Waiting call in the Callers list.
Indicates an incoming Call Waiting call.
John Burns
9054550055
Jun 8 2:41pm 2X
"2x" indicates this caller has called twice. The
display shows the date and time of the last call
from that caller.
You can view, scroll, and delete line items in the Callers List from the IP phone UI. You can also
directly dial from a displayed line item in the Callers List.
Managing Calls
Model 6753i IP Phone User Guide
135
Managing Calls
Accessing the Callers List
IP Phone UI
Use the following procedure to access the Callers List. Use the following illustration as a
reference.
Callers List
Key
Handsfree
Button
1. Press the Callers List Key. Press 2 and 5 to move through the Callers list. Press 2 to see the
most recent call, or 5 to see the oldest call on your list.
2. To dial the displayed number just press
or lift the Handset or press any line keys.
3. Press the Callers List Key to cancel.
Editing Entries in the Callers List
Important: The Caller List does not save changes. Editing in the Callers List is generally used if
you plan to call the number and need to add a prefix.
In the Callers List, if a dial pad key is pressed when a number and/or a name is displayed, the
cursor automatically adds the digit at the left side of the number to enable the entry of the prefix.
007
N
136
John Burns
9054550055
Jun 8 2:55pm
Model 6753i IP Phone User Guide
IP Phone UI
Use the following procedure to edit the Callers List. Use the following illustration as a reference.
Callers List
Key
Handsfree
Button
1. Press the Callers List Key.
2. Press 2 and 5 to find the entry you want to edit. Press 2 to view the most recent call, or 5 to
see the oldest call on your list.
3. Press any key on the dial pad to begin editing.
4. To move the cursor one digit to the right, press 4. To erase one digit to the left of the cursor,
press 3.
5. To dial the displayed number press
, or just lift the handset, or press any line keys.
Managing Calls
Model 6753i IP Phone User Guide
137
Managing Calls
Deleting Entries From the Callers List
You can delete individual items from the Callers List, or you can delete all items in the Callers
List.
IP Phone UI
Use the following procedure to delete an individual item from the Callers List. Use the following
illustration as a reference.
Delete Key
Callers List
Key
1. Press the Callers List Key.
2. Press 2 and 5 to find the item you want to delete.
3. Press the Delete Key.
4. Press the Delete Key again at the prompt to erase the item.
IP Phone UI
Use the following procedure to delete all items from the Callers List.
1. Press the Callers List Key.
2. Press the Delete Key.
3. Press the Delete Key again at the prompt to erase all items.
138
Model 6753i IP Phone User Guide
Downloading the Callers List to Your PC
You can download the Callers List to your PC for viewing using the Aastra Web UI. When you
download the Callers List, the phone stores the callerlist.csv file to your computer in
comma-separated value (CSV) format.
You can use any spreadsheet application to open the file for viewing. The following is an example
of a Callers List in a spreadsheet application. This file displays the name, phone number, and the
line that the call came in on.
Download the Callers List
Use the following procedure to download the Callers List to your PC using the Aastra Web UI.
Aastra Web UI
1. Click on Operation->Directory.
.
3. Click OK.
4. Enter the location on your computer where you want to download the Callers List and click
SAVE.
The callerslist.csv file downloads to your computer.
5. Use a spreadsheet application to open and view the Callers List.
Model 6753i IP Phone User Guide
139
Managing Calls
2. In the Callers List field, click on
A File Download message displays.
Managing Calls
Account Configuration (DND and Call Forwarding)
The 6753i has a feature that allows you to configure “Do Not Disturb” (DND) and “call
forwarding” (CFWD) for multiple accounts on the phone. You can set specific modes for the
way you want the phone to handle DND and CFWD. The three modes you can set on the phone
for these features are:
•
Account
•
Phone
•
Custom
The following paragraphs describe account-based DND and CFWD:
•
DND Account-Based Configuration
•
Call Forward Account-Based Configuration
DND Account-Based Configuration
"Do Not Disturb" (DND) is a feature on the phone that prevents the phone from ringing and
receiving incoming calls. When DND is enabled with "call forwarding" (CFWD), any incoming
calls can be call forwarded to voicemail or another number. See "“Call Forward Account-Based
Configuration”" on page 145 for more information about call forwarding to other numbers.
On the 6753i, you can set DND on the phone-side for a specific account or for all accounts on
the phone. You can set three modes for DND using the Aastra Web UI at the path, Basic
Settings->Preferences->General->DND Key Mode: Account, Phone (default), and Custom.
DND performs according to the mode you set.
You can then configure a DND key (for the phone or for an expansion module) using the Aastra
Web UI at the path, Operation->Programmable Keys. You can enable and disable DND by
toggling the key, or by setting DND for a specific account at the path,
Basic Settings->Account Configuration. Once you enable DND, "DND" displays on the LCD
for the applicable account.
1
Screenname1
DND On
Jan 1 12:96
Note: If there is only one account configured on the phone, then the mode
setting is ignored and the phone behaves as if the mode was set to “Phone”.
140
Model 6753i IP Phone User Guide
The following describes the key behavior for each DND mode.
•
Account - DND key toggles the account in focus on the IP Phone UI, to ON or OFF if DND
enabled for that account.
•
Phone - (default) DND key toggles all accounts on the phone to ON or OFF.
•
Custom - DND key displays custom screens on the IP Phone UI. User can select whether to
enable/disable DND per account, enable DND on all accounts, or disable DND on all
accounts.
The following table describes the key and Message Waiting Indicator (MWI) LEDs when you
enable DND on the IP Phone.
Key LED Behavior
for All Modes
MWI LED Behavior
for All Modes
DND key LED RED if current
account in focus has DND ON.
DND key LED OFF when current
account in focus has DND
disabled.
MWI LED ON if current account in
focus has DND ON.
MWI LED OFF if current account in
focus has DND OFF.
Note: If you make changes to the configuration for DND via the IP Phone UI,
you must refresh the Aastra Web UI screen to see the changes.
Configuring a DND Key
To configure a DND key, see the section, “Do Not Disturb (DND) Key” on page 62.
Note: If there is no DND key configured or if it is removed, DND is disabled on
the IP Phone.
Managing Calls
Model 6753i IP Phone User Guide
141
Managing Calls
Configuring DND Using the Aastra Web UI.
Aastra Web UI
Use the following procedure to configure DND using the Aastra Web UI.
1. Click on Basic Settings->Preferences->General.
2. In the “DND Key Mode” field, select a “do not disturb” (DND) mode to use on the phone.
Valid values are: Account, Phone (default), Custom. Default is Phone.
•
account
Sets DND for a specific account. DND key toggles the
account in focus on the phone to ON or OFF.
•
phone
(default) Sets DND ON for all accounts on the phone. DND key
toggles all accounts on the phone to ON or OFF.
•
custom
Sets the phone to display custom screens after pressing
the DND key, that list the account(s) on the phone.
The user can select a specific account for DND, turn
DND ON for all accounts, or turn DND OFF for all accounts.
Notes:
1. If there is only one account configured on the phone, then the mode setting is
ignored and the phone behaves as if the mode was set to “Phone”.
2. Using the Aastra Web UI, if you change the DND Key Mode to “phone”, all
accounts synchronize to the current setting of Account 1.
3. Click
142
to save your changes. The changes takes affect immediately without a reboot.
Model 6753i IP Phone User Guide
4. Click on Basic Settings->Account Configuration.
5. For each account, enable DND by placing a check mark in the box. Disable DND by
unchecking the box.
Notes:
1. If you selected “Account” or “Custom” mode in step 2, you can enable/
disable each account or all accounts as applicable. If you selected “Phone” mode,
the first account allows you to change the DND status for all accounts.
2. Number and name of accounts that display to this screen are dependant on the
number and name of accounts configured on the phone. In the screen in step 4,
Screenname1 is configured on Line 1, Screenname2 is configured on Line 2, and
Screenname3 is configured on Line 3. Only your Administrator can create
accounts for your phone. Contact your Administrator for more information.
6. Click
to save your changes. The changes takes affect immediately without a reboot.
Using DND Modes via the IP Phone UI
After you add a DND key to your phone, you can toggle the DND state using this key on the
phone. Use the following procedure to enable/disable DND on the IP Phone.
IP Phone UI
Notes:
1. If there is no DND key configured or if it is removed, DND is disabled on the
IP Phone.
2. If there is only one account configured on the phone, then the mode setting is
ignored and the phone behaves as if the mode was set to “Phone”.
3. Using the Aastra Web UI, if you change the DND key mode to “phone”, all
accounts synchronize to the current setting of Account 1.
Model 6753i IP Phone User Guide
143
Managing Calls
The following procedures assume you have already configured a DND key AND assumes there
are three accounts configured on the phone.
Managing Calls
DND in Account Mode
1. With the account in focus on the IP Phone UI, press the DND key to toggle DND ON or
OFF for the account.
2. Use the RIGHT and LEFT arrow keys to scroll through each account.
1
2
Screenname1
DND On
Jan 1 12:96
3
Screenname2
Jan 1 12:96
Screenname3
DND On
Jan 1 12:96
In the above example, Screenname1, Screenname2, and Screenname3, are three accounts
configured on the phone. Only Screenname1 and 3 have DND ON. Screenname 2 has DND
OFF.
DND in Phone Mode (Default)
1. Press the DND key to toggle DND ON or OFF for all accounts on the phone. Toggling to
ON enables DND on all accounts on the phone. Toggling to OFF disables DND on all
accounts on the phone.
2. Use the RIGHT and LEFT arrow keys to scroll through each account.
1
Screenname1
DND On
Jan 1 12:96
3
2
Screenname2
DND On
Jan 1 12:96
Screenname3
DND On
Jan 1 12:96
In the above example, toggling Screenname1 to DND ON, enabled DND for Screenname2 and 3
also.
144
Model 6753i IP Phone User Guide
DND in Custom Mode
1. Press the DND key on the phone. The screen displays a list of the accounts on the phone and
allows you to enable/disable a specific account or all accounts.
2. Use the UP and DOWN arrow keys to scroll through the accounts.
DND
1. Screenname1
Change
Done
DND
X
2. Screenname2
Change
Done
DND
3. Screenname3
Change
Done
DND
4. All Off
Done
Set
DND
5. All On
Done
Set
In the above example, Screenname1 and 3 have DND ON as indicated by a check mark (3).
Screenname2 has DND off as indicated by an X. Items 4 and 5 allow you to disable or enable
DND on all accounts, respectively.
3. Use the CHANGE key to enable or disable DND for a specific account.
4. Use the SET key to enable/disable DND for all accounts.
5. After making the change, press DONE and then Confirm (#) to save the change. Pressing
Apply Changes?
0 Cancel
# Confirm
Cancel (0) cancels the attempted change. The following screen displays after pressing a
DONE key:
Call Forward Account-Based Configuration
On the 6753i, you can set Call Forward (CFWD) on the phone-side for a specific account or for all
accounts on the phone. You can set three modes for CFWD using the Aastra Web UI at the path,
Basic Settings->Preferences->General->Call Forward Key Mode:
•
Account (default)
•
Phone
•
Custom
CFWD performs according to the mode you set.
Model 6753i IP Phone User Guide
145
Managing Calls
Call Forward (CFWD) on the IP phone allows incoming calls to be forwarded to another
destination.
Managing Calls
You can configure CFWD using the Aastra Web UI at the path,
Basic Settings->Account Configuration, OR you can configure CFWD using the IP Phone UI
at the path, Options->Call Forward.
Using the Aastra Web UI at the path, Operation->Programmable Keys, you can also configure a
CFWD key (on the phone or on an expansion module) to use as a shortcut for accessing the
CFWD menu on the phone.
The following describes the behavior for each CFWD mode.
•
Account - (default) The account mode allows you to configure CFWD on a per account
basis. Pressing a configured CFWD key applies to the account in focus.
•
Phone - The Phone mode allows you to set the same CFWD configuration for all accounts
(All, Busy, and/or No Answer). When you configure the initial account, the phone applies
the configuration to all other accounts. (In the Aastra Web UI, only the account you
configured is enabled. All other accounts are grayed out but set to the same configuration.)
Using the Aastra Web UI, if you make changes to that initial account, the changes apply to
all accounts on the phone.
•
Custom - The Custom mode allows you to configure CFWD for a specific account or all
accounts. You can configure a specific mode (All, Busy, and/or No Answer) for each
account independently or all accounts. On the 6753i, you can set all accounts to ALL On or
ALL Off.
Note: If there is only one account configured on the phone, then the mode
setting is ignored and the phone behaves as if the mode was set to “Phone”.
You can enable different CFWD rules/modes independently (for example, you can set different
phone numbers for Busy, All, and NoAns modes and then turn them on/off individually).
The following table describes the key and Message Waiting Indicator (MWI) LEDs when you
enable CFWD on the IP Phone.
Key LED Behavior
for All Modes
MWI LED Behavior
for All Modes
CFWD key LED RED if CFWD All,
CFWD Busy, or CFWD No Answer
is enabled for the account in focus.
CFWD key LED OFF if any CFWD
mode is disabled.
MWI LED ON if current account in
focus has CFWD ALL enabled.
MWI LED OFF if CFWD All is
disabled.
Note: If you make changes to the configuration for CFWD via the IP Phone UI,
you must refresh the Aastra Web UI screen to see the changes.
146
Model 6753i IP Phone User Guide
Configuring CFWD Using the Aastra Web UI
Aastra Web UI
Use the following procedure to configure CFWD using the Aastra Web UI.
1. Click on Basic Settings->Preferences->General.
2. In the “Call Forward Key Mode” field, select a call forward mode to use on the phone. Valid
values are: Account, Phone, Custom. Default is Account.
Account - (default) The account mode allows you to configure CFWD on a per account basis.
Pressing a configured CFWD key applies to the account in focus.
•
Phone - The Phone mode allows you to set the same CFWD configuration for all accounts
(All, Busy, and/or No Answer). When you configure the initial account, the phone applies the
configuration to all other accounts. (In the Aastra Web UI, only the account you configured is
enabled. All other accounts are grayed out but set to the same configuration.) Using the Aastra
Web UI, if you make changes to that initial account, the changes apply to all accounts on the
phone.
•
Custom - The Custom mode allows you to configure CFWD for a specific account or all
accounts. You can configure a specific state (All, Busy, and/or No Answer) for each account
independently or all accounts. On the 6753i, you can set all accounts to ALL On or ALL Off.
Note: If there is only one account configured on the phone, then the mode
setting is ignored and the phone behaves as if the mode was set to “Phone”.
3. Click
to save your changes.
The changes takes affect immediately without a reboot.
Model 6753i IP Phone User Guide
147
Managing Calls
•
Managing Calls
4. Click on Basic Settings->Account Configuration.
The illustration above shows 3 accounts configured on the phone. Accounts must be set up
by your System Administrator.
5. For each account, enable the CFWD state by placing a check mark in one or more of the
following “State” fields:
•
All
•
Busy
•
No Answer
The “All” option forwards all incoming calls for this account to the specified phone number
regardless of the state of the phone. The phone can be in the Busy or No Answer states, or
can be in the idle state. The phone still forwards all calls to the specified number.
The “Busy” option call forwards incoming calls only if the account is in the busy state. The
calls are forwarded to the specified phone number.
The “No Answer” option call forwards incoming calls only if the account rings but is not
answered in the defined number of rings. The call gets forwarded to the specified number.
Note: You can use the “Busy” and “No Answer” states together using different
forwarding phone numbers. If these states are enabled for an account (the “All”
state is disabled), and the phone is in the busy state when a call comes in, the
phone can forward the call to the specified phone number (for example,
voicemail). If there is no answer on the phone after the specified number of rings,
the phone can forward the call to a different specified number, such as a cell
phone number.
6. For each account, in the “Number” field, enter the phone number for which you want the
incoming calls to forward to if the phone is in the specified state.
If using the “Account” mode or “Custom” mode, you can enter different phone numbers for
each account.
148
Model 6753i IP Phone User Guide
Notes:
1. If you selected “Account” mode in step 2, you can enable/disable each
account or all accounts as applicable. You can enter different phone number for
each enabled state.
If you selected “Custom” mode, you can enable/disable each account or all
accounts as applicable. You can enter different phone numbers for each enabled
state.
If you selected “Phone” mode, all accounts are set to the same CFWD
configuration (All, Busy, and/or No Answer) as Account 1 on the phone. (In the
Aastra Web UI, only Account 1 is enabled. All other accounts are grayed out but
use the same configuration as Account 1.)
Using the Aastra Web UI, if you make changes to Account 1, the changes apply
to all accounts on the phone. Using the IP Phone UI, if you make changes to any
other account other then Account 1, the changes also apply to all accounts on the
phone. When enabling a CFWD state, you must specify a phone number for the
phone to CFWD to. The number you specify applies to all accounts of the same
mode.
2. Number and name of accounts that display to this screen are dependant on the
number and name of accounts configured on the phone. In the screen in step 4,
Screenname1 is configured on Line 1, Screenname2 is configured on Line 2, and
Screenname3 is configured on Line 3. The name for the account is specified by
your System Administrator. Contact your System Administrator for more
information.
7. For the "No Answer" state, in the “No. Rings” field, enter the number of times that the
account rings before forwarding the call to the specified number. Valid values are 1 through
20. Default is 1.
When using the “Account” mode or “Custom” mode, you can enter a different number of
rings for each account. If you use the Aastra Web UI to change the Call Forward Key Mode to
“Phone”, all accounts synchronize to Account 1.
9. Click
to save your changes.
The changes takes affect immediately without a reboot.
Model 6753i IP Phone User Guide
149
Managing Calls
8. (Optional) You can configure a Call Forward key on your phone to access the Call Forward
menus if desired. You can also access the Call Forward menu from the IP Phone UI at the path,
Options->Call Forward. To create a Call Forward key, see “Call Forward Key” on page 85.
Managing Calls
Using CFWD via the IP Phone UI
Once CFWD is enabled on your phone, you can access and change the configuration using the
IP Phone UI or the Aastra Web UI. You can access the CFWD menus by pressing a
pre-configured Call Forward key, or by selecting Options->Call Forward from the IP Phone UI.
The following procedure assumes you have already configured a CFWD key AND assumes
there are three accounts configured on the phone.
Notes:
1. If there is no CFWD key configured on the phone or it is removed, you can
still enable CFWD via the IP Phone UI at the path Options->Call Forward.
2. If there is only one account configured on the phone, then the mode setting is
ignored and the phone behaves as if the mode was set to “Phone”.
3. Using the Aastra Web UI, if you change the CFWD key mode to “Phone”, all
accounts synchronize to the current setting of Account 1.
CFWD in Account Mode
1. Use the RIGHT and LEFT arrow keys to scroll through each account.
1
Screenname1
CFWD All
Jan 1 12:96
2
3
Screenname2
Jan 1 12:96
Screenname3
CFWD Busy
Jan 1 12:96
In the above example, Screenname1, Screenname2, and Screenname3, are three accounts
configured on the phone. Screenname1 has “CFWD All” enabled, Screenname 2 has CFWD
disabled as indicated by no message displayed, and Screenname3 has “CFWD Busy”
enabled.
2. Press the Call Forward key. The Call Forward Mode screen displays. Use the UP and
DOWN arrow keys to scroll through each state type.
Indicates
CFWD Enabled
Indicates
no CFWD
phone number
configured
Indicates
CFWD Disabled
Cfwd Mode
1. All
Done
Change
Cfwd Mode
2. Busy
Done
Change
Cfwd Mode
3. NoAns
Done
X
Change
Cfwd Mode
4. All Off
Done
Set
Cfwd Mode
5. All On
Done
Set
!
In the above example, CFWD All is enabled as indicated by a check mark (3), CFWD Busy
is enabled but no call forward phone number configured as indicated by a !, and CFWD
NoAns is disabled, as indicated by an X.
150
Model 6753i IP Phone User Guide
3. Select a state for the account(s) in focus using the UP and DOWN arrow keys.
You can enable/disable any or all of the following states for an account:
•
All - Enables CFWD All for an account and forwards all incoming calls for that account, to the
specified number.
•
Busy - Enables CFWD Busy for an account and forwards incoming calls to a specified number
if DND has been enabled for that account OR if the account is currently engaged in another
call.
•
No Answer - Enables CFWD NoAns for an account and forwards incoming calls to a
specified number if the call has not been answered for the specified number of rings.
Note: If CFWD All AND CFWD Busy AND CFWD NoAns are all enabled
(and/or if the account has DND enabled), the CFWD All settings take precedence
over CFWD Busy and CFWD NoAns.
You can also use the following keys if required:
•
All Off - Disables all CFWD states for the current account in focus.
•
All On - Enables all CFWD states for the current account in focus.
4. Press the CHANGE key for the state you selected in step 3. Scroll to the CFWD State screen.
This displays the current state of the mode you selected. In the following example, the CFWD
All state is ON.
CFWD State Screen
to view
1. Cfwd State
On
Done
Change
1. Cfwd All
Use
Change
Cfwd State
On
Next
Cfwd State
Off
Next
Set
Set
5. Press the CHANGE key in the CFWD State screen. Press NEXT to toggle the state of the
CFWD mode ON or OFF. In the example in Step 4, you press NEXT to change the option to
OFF.
6. Press SET to save the change.
7. In the CFWD State screen, press the DOWN arrow key to scroll to the CFWD Number screen
and press CHANGE.
Managing Calls
.
1. Cfwd All
Use
to view
1. Cfwd State
On
Done
Change
CFWD Number Screen
2. Cfwd Number
Done
Model 6753i IP Phone User Guide
Change
Change
Cfwd Number
__
Cancel
Set
151
Managing Calls
8. Enter a phone number to apply to the current state in focus. When the phone is in the state
you specified, and a call comes into the phone, it forwards the call to the number you
specify.
9. Press SET to save the change.
10. For the CFWD No Answer state, In the CFWD Number screen, press the DOWN arrow
key to scroll to the CFWD No. Rings screen and press CHANGE.
1. Cfwd NoAns
Use
to view
1. Cfwd State
On
Done
Change
2. Cfwd Number
CFWD No. Rings Screen
Done
Change
Change
3. No. Rings
Done
Change
No. Rings
1
Next
Set
11. Press NEXT to select the number of rings to apply to the phone for call forwarding
incoming calls. Valid values are 1 to 20. Default is 1.
When the phone receives an incoming call, and call forward is configured on the phone, the
phone rings the number of times you specify in the No. Rings screen, and then forwards the
call if there is no answer.
12. Press SET to save the change.
13. Press DONE to save CFWD All Number, CFWD All State, CFWD Busy Number, CFWD
Busy State, CFWD No Answer Number, CFWD No Answer State, CFWD No Answer
Rings.
Each time you press DONE, the following “Apply Changes” screen displays.
Apply Changes?
0 Cancel
# Confirm
14. Press # to confirm the change(s) each time the “Apply Changes” screen displays. All
changes are saved to the phone.
152
Model 6753i IP Phone User Guide
CFWD in Phone Mode
1. Use the RIGHT and LEFT arrow keys to scroll through each account.
1
Screenname1
CFWD All
Jan 1 12:96
2
Screenname2
CFWD All
Jan 1 12:96
3
Screenname3
CFWD All
Jan 1 12:96
In the above example, Screenname1, Screenname2, and Screenname3, are three accounts
configured on the phone. All three accounts have CFWD enabled as indicated by the “CFWD
All” message.
Note: In ”Phone” mode, when you change the call forward configuration for an
account, the change applies to all accounts.
2. Press the Call Forward key. The Call Forward menu displays. Use the UP and DOWN arrow
keys to scroll through each state type.
Indicates
CFWD ALL
enabled
Indicates
no CFWD
phone number
configured for
Busy
Indicates
CFWD NoAns
enabled
Cfwd Mode
1. All
Done
Change
Cfwd Mode
2. Busy
Done
Change
Cfwd Mode
3. NoAns
Done
Change
Cfwd Mode
4. All Off
Done
Set
Cfwd Mode
5. All On
Done
Set
!
In the above example, the account has CFWD All and CFWD NoAns enabled as indicated by
a check mark (3). The CFWD Busy setting is enabled but no call forward phone number is
configured as indicated by a !.
You can enable/disable a specific account on the phone with any or all of the following states.
However, the configuration you set will apply to all accounts on the phone.
•
All - Enables CFWD All on the phone and forwards all incoming calls to the specified
number.
•
Busy - Enables CFWD Busy on the phone and forwards incoming calls to a specified
number if DND has been enabled OR if the phone is currently engaged in another call.
•
No Answer - Enables CFWD NoAns on the phone and forwards incoming calls to a
specified number if the call has not been answered for the specified number of rings.
Model 6753i IP Phone User Guide
153
Managing Calls
3. Select a state using the UP and DOWN arrow keys.
Managing Calls
Note: If CFWD All AND CFWD Busy AND CFWD NoAns are all enabled
(and/or if the account has DND enabled), the CFWD All settings take precedence
over CFWD Busy and CFWD NoAns.
You can also use the following keys if required:
•
All Off - Disables all CFWD states for the phone.
•
All On - Enables all CFWD states for the phone.
Note: In “Phone” mode, the initial configuration you set for an account applies
to all the accounts on the phone.
4. Press the CHANGE key for the mode you selected in Step 2. Scroll to the CFWD State
screen. This screen displays the current state of the mode you selected. In the following
example, the CFWD All state is ON.
Use
CFWD State
Screen
to view
1. Cfwd State
On
Done
Change
1. Cfwd All
Change
Cfwd State
On
Next
Cfwd State
Off
Next
Set
Set
5. Press the CHANGE key in the CFWD State screen. Press NEXT to toggle the state of the
CFWD state ON or OFF. In the example in Step 4, you press NEXT to change the option to
OFF.
6. Press the SET key to save the change.
7. In the CFWD State screen, press the DOWN arrow key to scroll to the CFWD Number
screen and press CHANGE
1. Cfwd All
Use
to view
1. Cfwd State
On
Done
CFWD Number
Screen
Change
2. Cfwd Number
Done
Change
Change
Cfwd Number
__
Cancel
Set
8. Enter a phone number to apply to the current state in focus. When the phone is in the state
you specified, and a call comes into the phone, it forwards the call to the number you
specify.
9. Press SET to save the change.
154
Model 6753i IP Phone User Guide
10. For the CFWD No Answer state, in the CFWD Number screen, press the DOWN arrow key
to scroll to the CFWD No. Rings screen and press CHANGE.
1. Cfwd NoAns
Use
to view
1. Cfwd State
On
Done
Change
2. Cfwd Number
Done
CFWD No.
Rings Screen
Change
Change
3. No. Rings
Done
Change
No. Rings
1
Next
Set
11. Press the NEXT key to select the number of rings to apply to the phone for call forwarding
incoming calls. Valid values are 1 to 20. Default is 1.
When the phone receives an incoming call, and call forward is configured on the phone, the
phone rings the number of times you specify in the No. Rings screen, and then forwards the
call.
12. Press SET to save the change.
13. Press DONE to save CFWD All Number, CFWD All State, CFWD Busy Number, CFWD
Busy State, CFWD No Answer Number, CFWD No Answer State, CFWD No Answer Rings.
Each time you press DONE, the following “Apply Changes” screen displays.
Apply Changes?
0 Cancel
# Confirm
14. Press # to confirm the change(s) each time the “Apply Changes” screen displays.
Managing Calls
All the same changes are saved to all accounts on the phone.
Model 6753i IP Phone User Guide
155
Managing Calls
CFWD in Custom Mode
1. Use the RIGHT and LEFT arrow keys to scroll through each account.
1
Screenname1
CFWD All
Jan 1 12:96
2
Screenname2
CFWD Busy
Jan 1 12:96
3
Screenname3
CFWD NoAns
Jan 1 12:96
In the above example, Screenname1, Screenname2, and Screenname3, are three accounts
configured on the phone. All three accounts have CFWD enabled as indicated by the “CFWD
All”, “CFWD Busy”, and “CFWD NoAns” messages.
Press the Call Forward key. The CFWD Account screens display. Use the UP and DOWN
arrow keys to scroll through each account.
Call Forward
1. Screenname1
Change
Done
Indicates
CFWD Enabled
Call Forward
X
2. Screenname2
Change
Done
Indicates
CFWD Disabled
Call Forward
!
3. Screenname3
Change
Done
Indicates
no CFWD phone
number
configured
Call Forward
4. All Off
Done
Set
Call Forward
5. All On
Done
Set
In the above example, Screenname1 has one or more CFWD states enabled as indicated by a
check mark (3). Screenname2 has one or more CFWD states disabled as indicated by an X.
Screenname3 has one or more CFWD states configured but a specific state has no call forward
phone number configured as indicated by a !. Items 4 and 5 allow you to disable or enable
CFWD on all accounts, respectively.
156
Model 6753i IP Phone User Guide
2. Select an account to configure. Press the CHANGE key. The CFWD Mode screen displays.
Use the UP and DOWN arrow keys to scroll through each state screen.
Indicates
CFWD All
enabled
Indicates
no CFWD
phone number
configured for
Busy
Indicates
CFWD NoAns
enabled
Cfwd Mode
1. All
Done
Change
Cfwd Mode
2. Busy
Done
Change
Cfwd Mode
3. NoAns
Done
Change
Cfwd Mode
4. All Off
Done
Set
Cfwd Mode
5. All On
Done
Set
!
In the above example, the account has CFWD All and CFWD NoAns enabled as indicated by a
check mark (3). The CFWD Busy setting is enabled for the account but has no call forward
phone number configured as indicated by a !.
3. Select a state for the account(s) in focus using the UP and DOWN arrow keys.
You can enable/disable any or all of the following states for a specific account or for all
accounts (with individual configurations):
All - Enables CFWD All for an account and forwards all incoming calls for that account, to
the specified number. The phone number can be different between accounts.
•
Busy - Enables CFWD Busy for an account and forwards incoming calls to a specified
number if DND has been enabled for that account OR if that account is currently engaged in
another call. The phone number can be different between accounts.
•
No Answer - Enables CFWD NoAns for an account and forwards incoming calls to a
specified number if the call has not been answered for a specified number of rings. The phone
number can be different between accounts.
Note: If CFWD All AND CFWD Busy AND CFWD NoAns are all enabled
(and/or if the account has DND enabled), the CFWD All settings take
precedence over CFWD Busy and CFWD NoAns.
You can also use the following keys if required:
•
All Off - Disables all CFWD states for the current account in focus or all accounts.
•
All On - Enables all CFWD states for the current account in focus or all accounts.
Model 6753i IP Phone User Guide
157
Managing Calls
•
Managing Calls
4. Press the CHANGE key for the mode you selected in step 2. Scroll to the CFWD State
screen. This displays the current state of the mode you selected. In the following example,
the CFWD All state is ON.
Use
CFWD State
Screen
to view
1. Cfwd State
On
Done
Change
1. Cfwd All
Change
Cfwd State
On
Next
Cfwd State
Off
Next
Set
Set
5. Press the CHANGE key in the CFWD State screen. Press NEXT to toggle the state of the
CFWD state ON or OFF. In the example in Step 4, you press NEXT to change the option to
OFF.
6. Press the SET key to save the change.
7. In the CFWD State screen, press the DOWN arrow key to scroll to the CFWD Number
screen and press CHANGE.
1. Cfwd All
Use
to view
1. Cfwd State
On
Done
CFWD Number
Screen
Change
2. Cfwd Number
Done
Change
Change
Cfwd Number
__
Cancel
Set
8. Enter a phone number to apply to the current state in focus. When the phone is in the state
you specified, and a call comes into the phone, it forwards the call to the number you
specify.
9. Press SET to save the change.
158
Model 6753i IP Phone User Guide
10. For the CFWD No Answer state, in the CFWD Number screen, press the DOWN arrow key
to scroll to the CFWD No. Rings screen and press CHANGE.
1. Cfwd NoAns
Use
to view
1. Cfwd State
On
Done
Change
2. Cfwd Number
Done
CFWD No.
Rings Screen
Change
Change
3. No. Rings
Done
Change
No. Rings
1
Next
Set
11. Press the NEXT key to select the number of rings to apply to the phone for call forwarding
incoming calls. Valid values are 1 to 20. Default is 1.
When the phone receives an incoming call, and call forward is configured on the phone, the
phone rings the number of times you specify in the No. Rings screen, and then forwards the
call.
12. Press SET to save the change.
13. Press DONE to save CFWD All Number, CFWD All State, CFWD Busy Number, CFWD
Busy State, CFWD No Answer Number, CFWD No Answer State, CFWD No Answer Rings.
Each time you press DONE, the following “Apply Changes” screen displays.
Apply Changes?
0 Cancel
# Confirm
14. Press # to confirm the change(s) each time the “Apply Changes” screen displays.
All changes are saved to the phone for all accounts.
Managing Calls
Model 6753i IP Phone User Guide
159
Managing Calls
Missed Calls Indicator
The IP phone has a "missed calls" indicator that increments the number of missed calls to the
phone. This feature is accessible from the IP phone UI only.
The number of calls that have not been answered increment on the phone’s idle screen as
"<number> New Calls". As the number of unanswered calls increment, the phone numbers
associated with the calls are stored in the Callers List. The user can access the Callers List and
clear the call from the list. Once the user accesses the Callers List, the "<number> New Calls" on
the idle screen is cleared.
Accessing and Clearing Missed Calls.
IP Phone UI
Use the following procedure to access and clear missed calls from the Callers List. Once you
display the Callers List, the "<number> New Calls" indicator clears. Use the following
illustration as a reference.
Callers List
Key
1. .Press Callers List key on the phone.
2. Use the 2 and 5 keys to scroll through the line items in the Callers List to find the line items
that have the b icon with the receiver ON. These are the missed calls to the phone.
3. To clear a line item from the Callers List, select the line item you want to delete and press
the Clear key. The line item is deleted from the Callers List.
160
Model 6753i IP Phone User Guide
Voicemail
The Voicemail feature on the 6753i IP phone allows you to use a line, configured with a phone
number for dialing out, to connect to a voicemail server.
For each assigned Voicemail number, there can be a minimum of 0 or a maximum of 1 Voicemail
access phone number.
The Voicemail list displays a list of phone numbers assigned to the 6753i that have registered
voicemail accounts associated with them.
Note: The Voicemail list does not display the voicemail access number.
The phone displays up to 99 voicemail messages for an account even if the number of voicemails
exceeds the limit.
Registered account numbers/URIs that exceed the length of the screen, either with or without the
voicemail icon and the message count, are truncated with an ellipse character at the end of the
number/URI string.
The end of the Voicemail list displays the number of new voicemail messages (if any exist).
Contact your System Administrator for lines configured for Voicemail.
Using Voicemail
IP Phone UI
1. Press the key on the phone that your System Administrator set up to access voicemail. After
pressing the key, the phone dials to access the voicemail server.
2. Use the 2 and 5 keys to scroll through the line items in the Voicemail list.
From a selected item in the Voicemail list, you can also lift the handset (go offhook) to make
an outgoing call using the voicemail access phone number.
Model 6753i IP Phone User Guide
161
Managing Calls
3. When you have selected a line item, press the
handsfree key, 4 Scroll Right key, or
press a line key to make an outgoing call using the voicemail access phone number associated
with the line for which the voicemail account is registered.
Additional Features
Additional Features
This section describes additional features you can use on the 6753i phone.
Star Codes
All of the main call handling and extension management features using star codes can be set on
your phone by your Administrator. Contact your System Administrator for more information.
If these have not been set up, you can dial any star code commands on the 55i phone the same
way you would on a regular telephone.
162
Model 6753i IP Phone User Guide
Suppress DTMF Playback
A feature on the IP phones allows you to enable or disable the suppression of DTMF playback
when a number is dialed from the keys on your phone.
When suppression of DTMF playback is disabled, and you press a key, the IP phone dials the
stored number and displays each digit as dialed, in the LCD window.
When the suppression of DTMF playback is enabled, the IP phone dials the stored number and
displays the entire number immediately in the LCD window, allowing the call to be dialed faster.
DTMF playback suppression is enabled by default. Disabling suppression of DTMF playback can
be configured using the Aastra Web UI.
Configuring Suppression of DTMF Playback
Aastra Web UI
Use the following procedure to configure suppression of DTMF playback.
Note: "Suppress DTMF Playback" is enabled by default.
1. Click on Basic Settings->Preferences->General.
Additional Features
2. Go to the "General" section.
3. The parameter “Suppress DTMF Playback” is enabled by default. (Disable this field by
unchecking the box). Default is enabled.
4. Click
to save your settings.
Model 6753i IP Phone User Guide
163
Additional Features
Display DTMF Digits
A feature on the IP phones allows users to enable or disable DTMF (dual-tone multi-frequency)
digits to display to the IP phone when using the keypad to dial, or when dialing from a
programmed key.
DTMF is the signal sent from the phone to the network that you generate when you press the
phone’s touch keys. This is also known as “touchtone” dialing. Each key you press on your
phone generates two tones of specific frequencies. One tone is generated from a high-frequency
group of tones and the other from a low frequency group.
If you enable the Display DTMF Digits parameter, the digits you are dialing from the keypad or
or from a programmable key display to the IP phone’s LCD display. This parameter is disabled
by default (no digits display when dialing).
You can enable the "Display DTMF Digits" parameter using the Aastra Web UI.
164
Model 6753i IP Phone User Guide
Configuring Display of DTMF Digits
Aastra Web UI
Use the following procedure to configure the display of DTMF digits on the IP phone.
Note: "Display DTMF Digits" is disabled by default.
1. Click on Basic Settings->Preferences->General.
2. Enable the "Display DTMF Digits" field by checking the check box.
Disable this field by unchecking the box). Default is disabled.
3. Click
to save your settings.
Additional Features
Model 6753i IP Phone User Guide
165
Additional Features
Enable/Disable Call Waiting
The call waiting feature notifies the user on an active call, of a new incoming call. You can
disable the call waiting feature, so that the new incoming call is automatically rejected by the
phone with a busy message.
If you disable call waiting on the phone, and the user is on a call, any further incoming calls
receive busy unless “Call Forward Busy” or “Call Forward No Answer and Busy” is
configured on the phone (for more information on
Call Forwarding, see “Call Forward Account-Based Configuration” on page 145.) It then
forwards the call according to the rule configured. The phone can only:
•
transfer the currently active call
or
•
accept transferred calls if there is no active calls.
If call waiting is disabled:
•
intercom calls are treated as regular incoming calls and are rejected.
•
pre-dialing with live dial pad disabled still accepts incoming calls.
•
the “Incoming Call Interrupts Dialing” parameter is ignored because the incoming call is
automatically rejected (for information on “Incoming Call Interrupts Dialing” see page 172).
•
the Missed Calls List does not get updated with details of calls.
•
the Blind Transfer feature on the phone may not work if two calls are made to the phone at
one time.
You can disable call waiting using the configuration files or the Aastra Web UI.
Enabling/Disabling Call Waiting
Aastra Web UI
Use the following procedure to enable or disable Call Waiting on the IP phone.
Note: "Call Waiting" is enabled by default.
166
Model 6753i IP Phone User Guide
1. Click on Basic Settings->Preferences->General.
2. Call Waiting is enabled by default. If required, disable the "Call Waiting" field by unchecking
the check box.
3. Click
to save your settings.
Additional Features
Model 6753i IP Phone User Guide
167
Additional Features
Play Call Waiting Tone
You can enable or disable the playing of a call waiting tone when you are on an active call and a
new call comes into the phone.
You can configure this feature using the Aastra Web UI.
Configuring Call Waiting Tone
Aastra Web UI
Use the following procedures to configure a call waiting tone on the IP phone.
Note: "Play Call Waiting Tone" is enabled by default.
1. Click on Basic Settings->Preferences->General.
2. A call waiting tone is enabled by default. If required, disable the "Play Call Waiting Tone"
field by unchecking the check box.
3. Click
168
to save your settings.
Model 6753i IP Phone User Guide
Stuttered Dial Tone
You can enable or disable the playing of a stuttered dial tone when there is a message waiting on
the IP phone.
You can configure this feature using the Aastra Web UI.
Configuring Stuttered Dial Tone
Aastra Web UI
Use the following procedures to configure stuttered dial tone on the IP phone.
Note: "Stuttered Dial Tone" is enabled by default.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 6753i IP Phone User Guide
169
Additional Features
2. Stuttered dial tone is enabled by default. If required, disable the "Stuttered Dial Tone" field
by unchecking the check box.
Additional Features
XML Beep Support
Using the Aastra Web UI, you can enable or disable a beep to be audible when the phone
receives an XML application using the "XML Beep Support" field at the path Basic
Settings->Preferences->General. If you disable this feature, then no beep is heard when the
XML application arrives to the phone.
If your System Administrator has set a value for this feature in a custom XML application or in
the configuration files, the value you set in the Aastra Web UI overrides the Administrator’s
setting. Setting and saving the value in the Aastra Web UI applies to the phone immediately.
Configuring XML Beep Support
Aastra Web UI
Use the following procedures to configure an XML beep on the IP phone.
Note: "XML Beep Support" is enabled by default.
1. Click on Basic Settings->Preferences->General.
2. "XML Beep Support" is enabled by default. If required, disable the "XML Beep Support"
field by unchecking the check box.
3. Click
170
to save your settings.
Model 6753i IP Phone User Guide
Status Scroll Delay
Using the Aastra Web UI, you can specify a scroll delay option that allows you to set the time
delay, in seconds, between the scrolling of each status message on the phone. You can specify this
setting in the "Status Scroll Delay (seconds)" field at the path Basic
Settings->Preferences->General. The default time is 5 seconds for each message to display before
scrolling to the next message. You can increase or decrease this time as required. Setting and
saving the value in the Aastra Web UI applies to the phone immediately.
Configuring Status Scroll Delay
Aastra Web UI
Use the following procedures to specify a status scroll delay on the IP phone.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 6753i IP Phone User Guide
171
Additional Features
2. Enter a value in the "Status Scroll Delay (seconds)" field. Valid values are: 1 to 25 seconds.
Default is 5.
Additional Features
Incoming Call Interrupts Dialing
The 6753i has a feature you can enable or disable called "Incoming Call Interrupts Dialing".
This feature is disabled by default. If you are dialing out on your phone, and you receive an
incoming call at the same time, the incoming call goes to an available line and the LED blinks to
let you know where the call was placed by the phone. If there is no line available to take the call,
a busy signal is sent to the caller. The LCD continues to display the number you were dialing.
If “Incoming Call Interrupts Dialing” is enabled, the incoming call interrupts your dialing
sequence and displays to the phone’s LCD for you to answer. You have a choice to ignore the
incoming call. If you choose to answer the incoming call, you can answer the call, finish the call,
and then hang up. You can still go back to the original outgoing call and finish dialing out.
You can enable or disable this parameter in the Aastra Web UI at the path Basic
Settings->Preferences->General.
Notes:
1. On a 6753i, you must use the down arrow key to ignore the call. To answer
the call, lift the handset or press the Speaker Key.
2. If you disable this field, and the phone receives an incoming call while you
are dialing an outgoing call, you can pick up the call and perform transfer or
conference as required.
Transfer/Conference Call Behavior
If you are dialing the phone to transfer or conference a call, and your phone receives an
incoming call, your dialing is never interrupted (regardless of whether the “Incoming Call
Interrupts Dialing” is enabled or disabled). For Transfer and Conference, the incoming calls
always go to an available line (other than the one you are using for dialing) and the incoming
call’s line LED blinks. The LCD still displays your dialing screen.
Intercom Behavior
If “Incoming Call Interrupts Dialing” is enabled and you are dialing an outgoing Intercom
call, the enabled interrupt setting takes precedence over an enabled “Allow Barge In” setting.
The incoming call interrupts your dialing on an outgoing intercom call. On an incoming
intercom call, the enabled “Allow Barge In” and “Auto-Answer” occurs while you are dialing to
transfer or conference the call. However, the incoming call goes to an available idle line, and the
LED blinks while you are dialing the second half of the conference or transfer.
If “Incoming Call Interrupts Dialing” is disabled, an incoming intercom goes to an available
idle line and the LED blinks for that line. The phone answers the call under all conditions.
172
Model 6753i IP Phone User Guide
Configuring "Incoming Call Interrupts Dialing"
Aastra Web UI
Use the following procedures to configure "Incoming Call Interrupts Dialing" on the IP Phone.
Note: "Incoming Call Interrupts Dialing" is disabled by default.
1. Click on Basic Settings->Preferences->General.
2. Enable the "Incoming Call Interrupts Dialing" field by checking the check box. Disable this
field by unchecking the box). Default is disabled.
3. Click
to save your settings.
Additional Features
Model 6753i IP Phone User Guide
173
Additional Features
Switch UI Focus to Ringing Line
You can configure a feature on the 6753i that controls the behavior of the phone when it receives
an incoming call when it is already in a connected call. When a call comes into the phone, and
the phone is already on a connected call, the phone switches focus to the ringing line to enable
the user to see who is calling them. You can turn off this functionality so that the phone stays
focused on the connected call. You can do this using the Switch Focus to Ringing Line
parameter in the Aastra Web UI.
Configuring “Switch Focus to Ringing Line” Using the Aastra Web UI
Aastra Web UI
Use the following procedure to enable or disable the “Switch Focus to Ringing Line” using the
Aastra Web UI.
1. Click on Basic Settings->Preferences->General.
2. The “Switch Focus to Ringing Line” field is enabled by default. To disable this field,
uncheck the box.
3. Click
174
to save your settings.
Model 6753i IP Phone User Guide
Preferred Line and Preferred Line Timeout
The 6753i has a feature called “preferred line” and “preferred line timeout”. If you enable the
preferred line parameter on your phone, after a call ends (incoming or outgoing), the display
switches back to the preferred line. Next time you go off-hook to make another call, you pickup on
the preferred line. You can enable the preferred line parameter using the Aastra Web UI at the
location, Basic Settings->Preferences->General. You can also set a preferred timeout parameter
that specifies the number of seconds it takes for the phone to switch back to the preferred line.
Note: You can configure “Preferred Line” and “Preferred Line Timeout” using
the Aastra Web UI only.
The following table provides the behavior of the preferred line focus feature with other features on
the phone.
Preferred Line Behavior
call return
The phone switches back to the focused line immediately after
the call ends.
speeddial
The line is already specified when the speeddial is created. The
phone switches back immediately after the call ends.
conference
For incoming calls, the phone switches back immediately after
the call ends.
transfer
For incoming or outgoing calls, the current behavior is that the
same line used to transfer the call does not change. For incoming
calls, the phone switches back immediately after the call
transfers.
blf
The phone switches back immediately after the call ends.
park
The phone switches back immediately after the call ends.
voicemail
The phone switches back immediately after the call ends.
redial
The phone switches back immediately after the call ends.
dialing
For incomplete dialing on a non-preferred line, the focus does not
change if some digits are entered.
If no digits are entered or digits were cleared, the focus changes
to preferred line after the time out has passed without activities.
caller id
If the "Switch UI Focus To Ringing Line" parameter is disabled,
the User is able to see the Caller ID when the phone switches the
focus to the ringing line.
factory default
Factory default and recovery mode clears the "preferred line" and
"preferred line timeout" parameters, and the phone operates in a
non-preferred line mode.
Additional Features
Phone Feature
Notes:
1.
If you specify a value of “0” for the preferred line parameter, it
disables the preferred line focus feature.
2.
If you specify a value of “0” for the preferred line timeout
parameter, the phone returns the line to the preferred line immediately.
Model 6753i IP Phone User Guide
175
Additional Features
Configuring “Preferred Line” and “Preferred Line Timeout”
Using the Aastra Web UI
Aastra Web UI
Use the following procedure to configure the Preferred Line and Preferred Line Timeout feature
using the Aastra Web UI.
1. Click on Basic Settings->Preferences->General.
2. In the “Preferred Line” field, select a preferred line to switch focus to after incoming or
outgoing calls end on the phone. Default is 1. Valid values are:
•
None (disables the preferred line focus feature)
•
1 to 9
For example, if you set the preferred line to “1”, when a call (incoming or outgoing) ends on
the phone (on any line), the phone switches focus back to Line 1.
3. In the “Preferred Line Timeout” field, enter the amount of time, in seconds, that the phone
switches back to the preferred line after a call (incoming or outgoing) ends on the phone, or
after a duration of inactivity on an active line. Default is 0. Valid values are:
•
0 to 999
4. Click
176
to save your changes.
Model 6753i IP Phone User Guide
Goodbye Key Cancels Incoming Calls
The 6753i has a feature that allows you to configure the Goodbye key to drop a second incoming
call or ignore incoming calls presented to the phone when you are on an active call. The parameter
is called "Goodbye Key Cancels Incoming Call" and is configurable via the Aastra Web UI.
If you enable this parameter, which is the default, pressing the Goodbye key rejects calls coming
into the phone while you are on an active call. When you disable this parameter, pressing the
Goodbye key hangs up the active call.
If you disable this feature, and the phone receives another call when an active call is already
present, the 6753i displays "3 Ignore Answer 4" on the LCD. For the 6753i, you must use the
Right and Left arrow keys to answer or ignore the call.
A User can set this parameter using only the Aastra Web UI.
Configuring Goodbye Key to Cancel Incoming Calls
Aastra Web UI
Use the following procedure to configure the Goodbye key to cancel incoming calls on the IP
Phone.
Note: "Goodbye Key Cancels Incoming Call" is enabled by default.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 6753i IP Phone User Guide
177
Additional Features
2. The "Goodbye Key Cancels Incoming Call" field is enabled by default. If required, disable
this field by unchecking the check box.
Additional Features
Using the Goodbye Key to Cancel Incoming Calls Feature
IP Phone UI
178
IF
THEN
"Goodbye Key Cancels Incoming Call" is
enabled AND a second call comes in while
you are on an active call,
press the Goodbye key to reject the second
incoming call.
"Goodbye Key Cancels Incoming Call" is
disabled AND a second call comes in while
you are on an active call,
press the Goodbye key to hang up on the
active call so you can answer the second
incoming call.
"Goodbye Key Cancels Incoming Call" is
disabled AND a second call comes in while
you are on an active call,
press the Left Arrow 3 key to ignore the
second incoming call and remain on the active
call
OR
press the Right Arrow 4 key to answer the
second incoming call.
Model 6753i IP Phone User Guide
UPnP Mapping Lines (for remote phones)
Universal Plug and Play (UPnP) is a standard that uses Internet protocols to enable devices to be
plugged into a network and automatically know about each other. With UPnP, when a user plugs a
device into the network, the device configures itself, acquires a TCP IP address, and uses a
discovery protocol based on the Internet's HTTP or HTTPS URL to announce its presence on the
network to other devices.
This method of device discovery on a network is called “Universal Plug and Play” or UPnP. If you
enable UPnP, and the phone is discovered on the network, port mappings are set up between the
phone and the Internet Gateway Device (IGD) in your network. The phone controls the opening,
closing, and polling of ports on the IGD. HTTP and SIP use a single port each. RTP/RTCP uses a
range of ports.
You can enable the UPnP mappings to specific lines on your phone. You set this configuration
using the Aastra Web UI at Basic Settings->Preferences->UPnP Mapping Lines.
Note: UPnP must be enabled on your remote phone before you can configure the
UPnP mapping lines. Contact your System Administrator for more information.
Configuring UPnP Mapping Lines
Aastra Web UI
Use the following procedure to configure the UPnP mapping lines on the IP phone.
1. Click on Basic Settings->Preferences->General.
3. Click
to save your settings.
Model 6753i IP Phone User Guide
179
Additional Features
2. The "UPnP Mapping Lines" field is set to 0 by default. If required, change the setting to a
specific line by selecting a line from the list. Valid values are 0 through 10. The line you select
is the line that your remote phone uses to perform Universal Plug and Play on the network you
are connecting to.
Additional Features
Message Waiting Indicator
You can configure the Message Waiting Indicator (MWI) to illuminate for a specific line or for
all lines. For example, if you configure the MWI LED on line 3 only, the LED illuminates if a
voice mail is pending on line 3. If you configure the MWI LED for all lines, the LED illuminates
if a voice mail is pending on any line on the phone (lines 1 through 9).
You configure the MWI indicator using the Aastra Web UI.
Configuring Message Waiting Indicator
Aastra Web UI
Use the following procedure to configure the message waiting indicator on a specific line or on
all lines on the IP phone.
Note: "Message Waiting Indicator Line" parameter is set to ALL lines by
default.
1. Click on Basic Settings->Preferences->General.
2. The "Message Waiting Indicator Line" field is set to ALL lines by default. If required,
change the setting to a specific line by selecting a line from the list. Valid values are All and
lines 1 through 9.
3. Click
180
to save your settings.
Model 6753i IP Phone User Guide
Incoming Intercom Call Features
Incoming Intercom
By default, the IP phone allows incoming intercom calls to be automatically answered without
having to set up an Icom key on your phone. The phone automatically plays a warning tone when
it receives an incoming intercom call. It also mutes the microphone. If the intercom call comes into
the phone while an active call is already present, the phone puts the active call on hold and answers
the intercom call.
You can change the behavior of how the phone handles incoming intercom calls by enabling/
disabling specific parameters using the Aastra Web UI. The following table describes these
features.
Incoming Intercom Features in
Aastra Web UI
Description
Microphone Mute
Allows you to enable or disable the microphone on the IP
phone for Intercom calls made by the originating caller.
Auto Answer
Allows you to enable or disable the IP phone to automatically
answer an Intercom call. If auto-answer is enabled on the IP
phone, the phone plays a tone (if "Play Warning Tone" is
enabled) to alert the user before answering the intercom call. If
auto-answer is disabled, the phone rejects the incoming
intercom call and sends a busy signal to the caller.
Note: Your Administrator can set a time period delay before
the phone automatically answers. Contact your System
Administrator for more information.
Play Warning Tone
Allows you to enable or disable a warning tone to play when
the phone receives an incoming intercom call on an active line.
Allow Barge In
Allows you to enable or disable how the phone handles
incoming intercom calls while the phone is on an active call.
You can mute or unmute the microphone on the IP phone for intercom calls made by the
originating caller. If you want to mute the intercom call, you enable this feature. If you want to
unmute (or hear the intercom call), you disable this feature. "Microphone Mute" is enabled by
default.
Model 6753i IP Phone User Guide
181
Additional Features
Microphone Mute
Additional Features
Auto-Answer/Play Warning Tone
The auto-answer feature on the IP phone allows you to enable or disable automatic answering
for an Intercom call. If “Auto-Answer” is enabled, the phone automatically answers an incoming
intercom call. If “Play Warning Tone” is also enabled, the phone plays a tone to alert you before
answering the intercom call. If “Auto-Answer” is disabled, the phone rejects the incoming
intercom call and sends a busy signal to the caller."Auto-Answer" and "Play Warning Tone"
are enabled by default.
Note: Your Administrator can set a time period delay before the phone
automatically answers. Contact your System Administrator for more information.
Allow Barge In
You can configure whether or not the IP phone allows an incoming intercom call to interrupt an
active call. The “Allow Barge In” parameter controls this feature. When you enable the this
parameter, which is the default value, an incoming intercom call takes precedence over any
active call, by placing the active call on hold and automatically answering the intercom call.
When you disable this parameter, and there is an active call, the phone treats an incoming
intercom call like a normal call and plays the call warning tone. "Allow Barge In" is enabled by
default.
Configuring Incoming Intercom Settings
Aastra Web UI
Use the following procedure to configure incoming Intercom settings on the IP phone.
1. Click on Basic Settings->Preferences->Incoming Intercom Settings.
182
Model 6753i IP Phone User Guide
2. The "Auto-Answer" field is enabled by default. The automatic answering feature is turned on
for the IP phone for answering Intercom calls. To disable this field, uncheck the box.
Note: If the Auto-Answer field is not checked (disabled), the phone rejects the
incoming intercom call and sends a busy signal to the caller.
3. The "Microphone Mute" field is enabled by default. The microphone is muted on the IP
phone for Intercom calls made by the originating caller. To disable this field, uncheck the box.
4. The "Play Warning Tone" field is enabled by default. If “Auto-Answer” is enabled, the phone
plays a warning tone when it receives in incoming intercom call. To disable this field, uncheck
the box.
5. The "Allow Barge In" field is enabled by default. If “Allow Barge In” is enabled, the phone
puts an active call on hold and answers the incoming Intercom call. To disable this field,
uncheck the box.
6. Click
to save your settings.
Using Redial Key for “Last Number Redial”
The IP phone has an enhanced redial user interface that allows a user to quickly redial the last
number that was dialed out from the phone. You can:
•
Press the REDIAL button twice to redial the last number dialed.
•
Press the REDIAL button once, scroll the list of numbers, then press the REDIAL button again
to dial the number that displays on the screen.
The “last number redial” feature for the Redial key is static and is not configurable.
Additional Features
Model 6753i IP Phone User Guide
183
Additional Features
Group RTP Paging (receives RTP streams)
You can configure the phone to allow it to receive a Real Time Transport Protocol (RTP) stream
from pre-configured multicast address(es) without involving SIP signaling. This is called Group
Paging on the IP phones. You can specify up to 5 multicast addresses that the phone listens for
on the network. This feature is configurable using the Aastra Web UI only.
The 6753i in the local network listens for RTP on the preconfigured multicast address. The
Phone displays the “Paging” message to the phone’s LCD. It uses the G711 uLaw CODEC for
multicast RTP.
The recipient can drop the incoming page if required. The recipient can also set Do Not Disturb
(DND) to ignore any incoming pages.
For incoming RTP multicasts, the ringing display is dependant on the setting for the “Allow
Barge-In” parameter. (See “Allow Barge In” on page 182.) If this parameter is disabled, and
there is no other call on the phone, then the paging is automatically played via the default audio
device.
If there is an existing call on the phone, the call initially displays in the ringing state. The user
has the option to accept/ignore the call. If the “Allow Barge-In” parameter is enabled, the RTP
multicast call barges in, and any existing calls are put on hold.
If an RTP multicast session already exists on the phone, and the phone receives another
incoming RTP multicast session, the priority is given to the first multicast session and the second
multicast session is ignored. The behavior for the incoming calls in this case is also based on the
setting for the “Allow Barge-in” parameter. The incoming call is handled as if there were an
existing call already on the phone.
184
Model 6753i IP Phone User Guide
Configuring Group RTP Paging
Aastra Web UI
Use the following procedure to configure RTP streaming on the receiving end for Paging
applications using the Aastra Web UI.
1. Click on Basic Settings->Preferences->Group Paging RTP Settings.
Group Paging RTP Settings
Enter the IP address in dotted decimal format.
(for example, 239.0.1.15:10000,239.0.1.20:15000)
You can enter up to 5 listening multicast addresses.
If this field is blank, the Paging Listening capability is disabled on the phone.
Notes:
1. Recipient of a Paging call can set a global “Do Not Disturb” (DND) to ignore
any incoming pages.
2. For incoming Paging, the phone uses the Intercom configuration settings. The
incoming Page is dependant on the “Allow Barge-In” parameter setting and the
“Idling/On Call” state.
3. Click
to save your settings.
Model 6753i IP Phone User Guide
185
Additional Features
2. In the “Paging Listen Addresses” text box, enter the multicast IP address(es) and port number
on which the phone listens for incoming multicast RTP packets.
Additional Features
Use LLDP ELIN
The 6753i IP Phone supports Link Layer Discovery Protocol for Media Endpoint Devices
(LLDP-MED), and Explicit Congestion Notification (ECN) Emergency Location Identification
Number (ELIN). LLDP ELIN allows the phone to use the location information sent by the
switch, as a caller ID for making emergency calls.
Note: If the phone receives location information in ECN ELIN format (10 to 25
numeric string), the phone replaces the caller ID SIP header with the ECN ELIN
value and the SIP URI does not change. The phone determines if this is an
emergency number by checking the emergency dial plan configured on the phone.
You can enable or disable the LLDP ELIN on the IP Phones using the Aastra Web UI.
For more information about LLDP-MED and LLDP ELIN, contact your System Administrator.
Configuring LLDP ELIN
Aastra Web UI
Use the following procedure to enable or disable LLDP ELIN using the Aastra Web UI.
1. Click on Basic Settings->Preferences->General.
2. The "Use LLDP ELIN" field is enabled by default. If required, disable this field by
unchecking the check box.
3. Click
186
to save your settings.
Model 6753i IP Phone User Guide
Shared Call Appearance (SCA) Call Bridging
Shared Call Appearance (SCA) is when incoming calls are presented to multiple phones
simultaneously. For example, it is the ability to assign the boss' extension to a button on the
secretary's phone. Calls can be transferred between two phones with the same extension button by
simply putting the call on hold at one phone and picking it up on the other. Status LEDs light and
flash in unison, allowing all people sharing the extension to see the status at a glance.
The phones include an enhanced SCA for the servers that support call bridging and allows two or
more SCA users to be connected in a call with a third party.
Refer to the following example.
Phone 1
SCA phone 1 answers.
When 2 and 3 pickup,
1 can hangup.
Phone A calls the SCA number and
all the phones in the SCA enironment
Phone A
ring.
Phone 2
SCA Environment
Phone 3
Note: A user can place a call on hold while in an SCA bridged call, by pressing the SCA line key.
SCA phone 2 joins by
pressing SCA line. When
phone 1 hangs up, 2 is still
connected. Phone 2 can
press the line key to
put SCA call on hold
leaving 3 still connected
to 1.
SCA phone 3 joins by
pressing SCA line. When
phone 1 hangs up, 3 is still
connected. Phone 3 can
press the line key to
put SCA call on hold
leaving 2 still connected
to 1.
Note: Your Administrator must enable/disable the beep on the server-side.
If a phone is configured for SCA bridging and it attempts to join a call, but the account on the
server does not have this functionality enabled, an error message displays to the LCD on the
phone.
The SCA call bridging feature is disabled by default on all phones. Your Administrator can enable/
disable this feature if required. Contact your System Administrator for more information.
Model 6753i IP Phone User Guide
187
Additional Features
Using the example above, when a call comes into Phone 1, Phone 2 and Phone 3 can pickup the
same call by pressing the SCA line key. Phone 2 and 3 display the call they are bridging into on the
LCD of the phones. Existing SCA parties in a bridge or one-to-one call hear an audible beep when
another party has joined the call.
Additional Features
Keys States and LED Behavior
There are two call states on the phones that support SCA bridging:
•
Bridge-active - A bridged call is in progress
•
Bridge-held - The 3rd-party (i.e., non-SCA party) in the bridge is on hold.
The following tables provide the key states and LED behavior in an SCA bridge call for users
involved in an SCA call and users not involved in the SCA call.
Line Keys and Idle Screens
State
Call LED
Call Caller ID
Non-Call LED
Non-Call Caller ID
Idle
N/A
N/A
Off
N/A
Seized
Solid Green
None
Solid Red
None
Progressing (outgoing call)
Green
Called Part7
Solid Red
None
Alerting (incoming call)
Blinking Unselected Red
N/A
Active
Solid Green
Far-end
Solid Red
Far-end
Held
Slow Flashing Green
Far-end
Slow Flashing Red
Far-end
Hold private
Slow Flashing Green
Far-end
Solid Red
Far-end
Bridge-active
Solid Green
Far-end
Solid Red
Far-end
Bridge-held
Slow Flashing Green
Far-end
Solid Red
Far-end
Programmable Line Keys
State
Call Icon
Call LED
Non-Call Icon
Non-Call LED
Idle
Small circle
None
Small circle
None
Seized
N/A
N/A
Sold Circle
Solid Red
Progressing (outgoing call)
Empty circle
Solid Red
Sold Circle
Solid Red
Alerting (incoming call)
Empty blinking circle
Flashing Red
N/A
N/A
Active
Empty circle
Solid Red
Sold Circle
Solid Red
Held
Reverse empty blinking
circle
Slow Flashing
Red
Sold Reverse Circle Slow Flashing Red
Hold private
Reverse empty blinking
circle
Slow Flashing
Red
Sold Circle
Solid Red
Bridge-active
Empty circle
Solid Red
Sold Circle
Solid Red
Bridge-held
Reverse empty blinking
circle
Slow Flashing
Red
Sold Circle
Solid Red
188
Model 6753i IP Phone User Guide
Line key Phone Behavior
State
Call Line Key Pressed
Non-Call Line Key Pressed
Idle
N/A
Attempt to seize the line
Seized
Hang up
Ignore
Progressing
Hang up
Ignore
Alerting
answer
N/A
Active
Hold
Bridge
Held
Retrieve
Bridge
Hold private
Retrieve
Ignore
Bridge-active
Hold
Bridge
Bridge-held
Retrieve
Bridge
Additional Features
Model 6753i IP Phone User Guide
189
Available Features Enabled by Administrators
Available Features Enabled by Administrators
There are features on your IP Phone that you can use ONLY if an Administrator has enabled
them on your phone. Those features are described in this section. Contact your System
Administrator for more information.
Outgoing Intercom Calls
If your System Administrator configures the outgoing intercom feature on your phone, pressing
the Icom button allows your phone to find an available line and place an intercom call to a
recipient. To use this feature, you must configure an intercom key on your phone. For more
information about configuring and using an Icom key, see “Intercom Key” on page 100.
Missed Call Summary Subscription
A feature on the IP phones allows missed calls that have been redirected by the server, to be
incremented in the missed calls indicator on the phone it was initially directed to. This feature is
called the Missed Call Summary Subscription and can be configured by your System
Administrator. For this feature to work, you must configure voicemail on the phone that the call
was initially directed to.
For example, phones A, B, and C are connected to the server. Your Administrator configures the
server to direct calls coming into phone B (which has voicemail configured) to be forwarded to
phone C. When phone A calls phone B, the server forwards the call to phone C. With the Missed
Call Summary Subscription enabled, phone B receives notification from the server that the
call was forwarded and the missed calls indicator is incremented on phone B. See the illustration
below.
Phone A
A calls B
Phone C
Phone B
B fowards call to C
Missed calls indicator increments on phone B.
: Voicemail must be configured on phone B.
Note:
Note: Your System Administrator can configure the Missed Call Summary
Subscription feature on a global or per-line basis.
190
Model 6753i IP Phone User Guide
Customizable Callers List Key
Your System Administrator can specify an XML URI that creates a custom Callers List application
for your phone. When you press the Callers List key, the phone accesses a custom XML URI
Callers List instead of the standard Callers List. Contact your System Administrator for more
information.
Autodial (Hotline and Warmline)
•
Hotline: The IP phone immediately dials a preconfigured number when you lift the handset.
•
Warmline: The IP phone waits for a specified amount of time after you lift the handset before
dialing a preconfigured number. If you do not dial a number within the time allotted, then the
IP phone begins to dial the number.
The Autodial feature is available on a global or per-line basis. Contact your System Administrator
for more information.
Notes:
1. Any speeddial numbers that you configure on your IP phone are not affected
by autodial settings.
2. If Autodial is configured on your phone, any lines that function as hotlines do
not accept conference calls, transferred calls, and/or intercom calls.
Model 6753i IP Phone User Guide
191
Available Features Enabled by Administrators
Your System Administrator can configure an autodial feature on your phone. If autodial is enabled,
the phone automatically dials a preconfigured number whenever it is off-hook. Depending on the
configuration specified by your Administrator, the Autodial functions as either a “hotline”, or as a
“warmline,” as follows:
Available Features Enabled by Administrators
Centralized Conferencing
The 6753i supports centralized conferencing for Sylantro and Broadsoft servers. This feature
provides centralized conferencing on the SIP server (versus localized, on the phone). Your
System Administrator must enable this feature on your phone before you can use centralized
conferencing.
Centralized Conferencing allows you to perform the following:
•
Conference two active calls together into a conference call.
•
When on an active conference call, invite another party into the call.
•
Create simultaneous conference calls on the same IP phone (Sylantro servers only). For
example, a user at extension 2005 could create two conferences, and put one conference on
hold while conversing with the other party:
— Line 1: conference together extensions 2005, 2010, and 2020.
— -Line 2: conference together extensions 2005, 2011 and 2021.
•
Disconnect from an active conference call while allowing the other callers to remain
connected.
•
Add unlimited number of users to a conference (dependent on the limitations of the server).
•
Join two active calls together into a conference.
•
Join incoming or outgoing active calls to any existing conference.
Reference
For more information about using Centralized Conferencing, see “Centralized Conferencing (for
Sylantro and Broadsoft Servers)” on page 120.
Answer and Ignore Keys for XML Applications
If you are accessing XML applications on your phone and a call comes in, your System
Administrator can create "Answer" and "Ignore" keys that you can use to either answer the
incoming call, or ignore it.
An XML application can display
here while a call is coming in.
Ignore
Answer
When the 3 Ignore Answer 4 line displays, you can press the Right Arrow key (Answer) to
answer the incoming call without disturbing the current XML application. When you answer the
call, the 3 Ignore Answer 4 line disappears from the LCD. Pressing the Left Arrow key
(Ignore) ignores the incoming call without disturbing the current XML application. Contact your
System Administrator for more information.
192
Model 6753i IP Phone User Guide
Playing a WAV File On Your Phone
If enabled by your Administrator, the 6753i IP Phone can play a WAV file. A WAV file is an audio
file format standard for storing an audio bit stream on a system in raw, uncompressed format or
compressed format to reduce the file size.
A WAV file is streamed to the phone using the HTTP protocol.
The WAV feature supports the following:
Streaming of the WAV file to allow it to be locally played
•
Allows you to abort the audio streaming by pressing the Goodbye key on the phone.
•
Supports the HTTP file download protocol
•
Supports the aLaw and uLaw codecs
•
Plays the WAV file only if the phone is idle.
•
WAV audio file starts only when 4 seconds of the audio data (or the complete file) has been
accumulated.
•
Follows the standard phone behavior of speaker/head set/hand set.
IP Phone UI Screen During WAV Streaming
The 6753i screen displays the following during WAV streaming.
Streaming
00:10
To abort the WAV streaming, press any of the following:
•
Goodbye key
•
Drop softkey
You can also place the handset (if in use) on hook.
Using the Keypad During Active XML Applications
If enabled by your Administrator, the 6753i IP Phone can allow you to continue using your keypad
keys during active XML applications on your phone. This feature is applicable only when your
phone is in the connected state. By default, the phone suppresses dialpad events when an XML
object is in focus, so your Administrators must enable the keypad to be used during active XML
applications. Contact your System Administrator for more information.
Model 6753i IP Phone User Guide
193
Available Features Enabled by Administrators
•
Available Features Enabled by Administrators
Key Redirection
Conference, Transfer, Redial, Intercom Keys and Voicemail Option
If enabled by your Administrator, the Conference, Transfer, Redial, and Intercom keys, as well
as the Voicemail option, can be redirected to XML scripts.This allows the server to provide the
phone with Redial, Transfer (Xfer), Conference (Conf), and Intercom (Icom) key features, and
the Voicemail option feature, rather then accessing them from the phone-side. By default, the
server-side keys function the same as the phone-side key features.
Notes:
1. Key remapping takes precedence over redirecting.
2. Disabling the redial, conference, or transfer features on the phone
also disables the redirection of these keys.
Contact your System Administrator for more information about this feature.
Options Key
If enabled by your Administrator, the Services Menu on the 6753i IP Phone can be redirected to
an XML script. This allows the server to provide the phone with available options, rather then
accessing them from the phone-side. You access the XML script by selecting the Services Menu.
You can still access the Services Menu from the phone-side by pressing and holding the Options
key to display the phone-side Services Menu.
IMPORTANT NOTES
•
If no Options URI script is configured, the local Options Menu on the phone displays as
normal.
•
If you configure password access to the Options Menu, this password is required when
accessing the local Option Menu, but is not required for the Options Key redirection feature.
•
Pressing the Options Menu for redirection from the server does not interfere with normal
operations of the phone (for example, pressing the options menu when on a call does not
affect the call).
•
If the phone is locked, you must unlock the phone before accessing the Options Menu
redirect feature. After pressing the Options Key, the phone displays a screen that allows you
to unlock the phone before continuing.
•
On the 6753i, the redirection feature works after selecting the Services Menu. To display the
original Options Menu, press and hold the Options key.
Contact your System Administrator for more information about this feature.
194
Model 6753i IP Phone User Guide
XML Applications and Off-Hook Interaction
If enabled by your Administrator, the 6753i can be prevented from going into the off-hook/dialing
state when the handset is off-hook and the call ends. This feature is disabled by default and must
be enabled by your Administrator. The disabled behavior is as follows:
Contact your System Administrator for more information about this feature.
XML Override for a Locked Phone
The 6753i has a feature that allows a locked phone to be overridden when an XML application is
sent to the phone. This feature also allows you to still use programmable keys/expansion module
keys applicable to the XML application even though the phone is locked. However, any keys NOT
associated with the XML application cannot be used when the phone is locked.
Also, XML Get Requests override the locked feature on the phone so that any programmable key
pressed by the user that initiates a Get Request continues to get sent.
Only a System Administrator can configure the feature of "XML override for a locked phone".
RTP Recording and Simultaneous Playing
The IP Phones now allow for Real-Time Transport Protocol (RTP) recording and simultaneous
playing of an audio file via XML commands created by your Administrator. The RTP and
multicast RTP commands allow the phone to send/receive an RTP stream to/from given multicast/
unicast addresses (without involving SIP signaling).
Notes:
1. When an RTP stream is being sent with RTP recording and simultaneous
playing (mix), the IP Phone LCD displays an icon with an ‘m’ on top to indicate
that a mixed RTP stream is being sent.
2. When RTP stream is being received with RTP recording and simultaneous
playing (mix), you can use the volume controls on the IP phone to adjust the
volume (increase or decrease) to your specifications.
Contact your System Administrator for more information about this feature.
Model 6753i IP Phone User Guide
195
Available Features Enabled by Administrators
You are in a call using the handset and the phone displays an XML application. The far-end
terminates the call, and a new XML application gets pushed/pulled onto the display. Since the
handset is off-hook and in idle mode, the "offhook idle timer" starts. When this timer expires, the
phone applies dial tone and moves to the off-hook/dialing state, which then destroys the XML
application that was being displayed.
Available Features Enabled by Administrators
“Hold” Feature Enhancement (for Broadsoft Servers)
The Hold feature allows you to put an active call on “hold,” then retrieve the call later. This
enhancement is intended for IP phones operating with servers that support RFC3264 (for
example, Broadsoft). If a server does not support RFC3264, then the IP phones do not use
RFC3264 functionality.
Configurable Save and Delete Keys
There are six function keys on the 6753i phone located to the left of the paper label. Your System
Administrator can make the Save and Delete keys (Keys 1 and 2) programmable keys with the
same functions that are available for the other programmable keys.
By default, the Save key allows you to save entries to the Directory and perform a Save-To from
the Callers List. It also allows you to save speeddial information to a programmable key. You
can also use the Save key while using specific XML applications.
By default, the Delete key allows you to remove entries from the Directory List and Callers List.
(Must enter the Directory or Callers list and select an entry, then press twice to delete entry).
Once the Save and Delete keys are made configurable, you can change the function of the keys
using the Aastra Web UI.
IMPORTANT: If you change the functions of the Save and Delete keys, and then an
Administrator locks Keys 1 and 2, the functions are automatically set back to the default settings
of "Save" and "Delete".
Authentication Support for HTTP/HTTPS Download Methods Used with
Broadsoft Client Management System (CMS)
If enabled by an Administrator, the 6753i has authentication support when using HTTP or
HTTPS as download protocols (as per RFC 2617). When a phone is connected to a Broadsoft
Server using the CMS tool, a LOGIN key displays. Pressing the LOGIN key displays a login
screen with Username and Password. Username can be up to 40 characters and Password can be
up to 20 characters. A System Administrator can optionally configure a Domain Name to be
used as the Username (e.g. username@domain.com). A user can navigate the screen using the
navigation keys (arrow keys) on the phone. The screen provides a SUBMIT key for submission
of the field information, and a CANCEL key for exiting the login screen. Appropriate messages
display if the phone reaches a timeout while trying to connect to the server, or if a Username or
Password are incorrect.
Once the login information for a specific user is entered and accepted by the server, the phone
reboots and downloads the user profile.
196
Model 6753i IP Phone User Guide
IP Phone UI when Broadsoft CMS is Enabled
When the Broadsoft CMS feature is enabled on the IP Phone, the following screens display:
Login Screen
9054550055
Sat Jun 8 2:55pm
=Log In
Please Enter:
Username: _
=Submit
=Next
Password Screen
Please Enter:
Password: _
=Cancel
Model 6753i IP Phone User Guide
Available Features Enabled by Administrators
Username Screen
=Submit
197
Available Features Enabled by Administrators
Diverting Calls from Your Phone
Your Administrator can enable/disable a feature on your phone that allows incoming calls to be
diverted to another phone if required.
When an outgoing call from your phone is being diverted to another destination (i.e., via call
forward), the phone displays the Caller ID (phone number and/or caller name) of the new
destination and the reason for the call diversion. Similarly, at the new destination, the Caller ID
of the original call destination displays.
Call Diversion Example
1
Tim calls Mark at x400.
2
Mark’s phone is busy.
3
Mark’s phone diverts the incoming call to another destination (Roger @ x 464).
4
Tim’s phone displays name and extension of where the call is being diverted to and
reason for diverting the call. The screen scrolls between Screen 1 and Screen 2.
5
Roger’s phone accepts the call and displays the name and number of the phone the
incoming call (Tim) and the name (or number) of the original destination (Mark). The
screens scroll between Screen 1 and Screen 2..
See examples of the phones’ LCD below.
The diversion LCD screens scroll every 3 seconds.
Tim’s Phone @ x462
Roger’s Phone @ x464
diverted to
Roger @ 464 receives the incoming call from Tim
divertted from Mark
Tim @ 463 calls Mark’s phone which is busy
and diverts to Roger.
1
Roger
464
2
Diverting:
User-Busy
3-Line LCD Display
1
Tim
462
2
Via:
Mark
3-Line LCD Display
To enable this call diverting feature, contact your System Administrator.
198
Model 6753i IP Phone User Guide
Display of Call Destination Information
By default, your phone displays call destination information if your phone is configured to forward
calls to other destinations. The call destination information displays on multiple screens that scroll
every 3 seconds. The following example shows call destination information on the 6753i IP Phone.
Call Destination Information
1
Bob
2
0409123456
To:
Alice One
Note: When both call diversion and call destination are enabled, the information
displays to the phone’s screens in the following order:
Screen 1
Caller info
Screen 2
Call destination
Screen 3
Call diversion
If your phone does not display call destination information, your System Administrator may have
disabled this feature. Contact your System Administrator for more information.
Model 6753i IP Phone User Guide
199
Available Features Enabled by Administrators
6753i IP Phone
Model M670i Expansion Module
Model M670i Expansion Module
The 6753i IP Phone offers an optional M670i Expansion Module that attaches to the right side of
the phone to provide additional keys.
Model M670i
The M670i provides 18 keys in each column (totaling 36 keys) on the keypad. Each key
provides an LED for indicating call status. The M670i provides a paper label for convenient key
labeling.
The Expansion Module keys support the following functions:
•
none
•
pickup
•
line
•
Last Call Return (lcr)
•
speeddial
•
Call Forward
•
do not disturb (DND)
•
BLF/Xfer
•
Busy Lamp Field
(BLF)
•
Speeddial/Xfer
•
BLF List
•
Directory
•
Auto Call Distribution
(ACD)
•
Callers List
•
Directed Call Pickup
•
Conference
•
Extensible Markup
Language (XML)
•
Transfer
•
flash
•
Intercom
•
sprecode
•
Services
•
park
•
Phone Lock
•
Paging
You can configure the keys using the Aastra Web UI at the path,
Operation->Expansion Module <N> when an Expansion Module is attached to the 6753i IP
Phone.
200
Model 6753i IP Phone User Guide
Reference
For more information about configuring the expansion module keys with these functions, see the
“Programmable Keys” on page 48.
Using the Expansion Module
M670i Expansion Module
After configuring the keys on the M670i Expansion Module, you can record the name of the key
on the paper labels provided with the Expansion Module. Press the key you want to use when
applicable.
Keys
Lock Phone
BLF Key
Office (speeddial)
For more information about configuring keys, see “Programmable Keys” on page 48.
For more information about installing the M670i module on your phone, see the Aastra 6753i IP
Phone Installation Guide.
Press-and-Hold to Create a Speeddial Key
You can press and hold an expansion module key to create a speeddial key and configure it the
same way you configure a speeddial key on the phone.
For a procedure on creating a speeddial key, see “Press-and-Hold to Create a Speeddial (applicable
to programmable keys, keypad keys, expansion module keys)” on page 53.
Model 6753i IP Phone User Guide
201
Model M670i Expansion Module
References
Troubleshooting Solutions
Why is my display blank?
Ensure that power is being provided to your phone. Make sure your phone is plugged into a
power source.
Why is my speakerphone not working?
If you press the
button and the speaker light flashes and you do not hear dial tone through
the speaker phone, the Set Audio option in the phone’s Options list has been set up for headset
use. Press
a second time and if the light goes out, the phone has been set up to be used
only with a headset or handset. If the light stays on steady and you hear dial tone, the phone has
been set up so that you can alternate between the speakerphone and the headset by pressing
. See the section, “Set Audio” on page 27 for instructions on how to change the Set Audio
option.
Why can’t I get a dial tone?
Check for any loose connections and that the phone has been installed properly. For installation
instructions, please refer to the “Installation and Setup” section in the Aastra 6753i Installation
Guide provided with your phone.
Why doesn’t my phone ring?
Check the ring volume on your phone. It may be turned down or turned off. To adjust the ringer
volume setting, press the volume button when the phone is on-hook and idle. For more
information, refer to the “Adjusting Volume section” in the Aastra 6753i Installation Guide
provided with your phone.
Why is the light not coming on with a new Voice Mail Message?
Your phone system or service provider must provide “Visual” Message Waiting service for this
function to work. Check with your System Administrator for more information.
Why is my handset not working?
Check to ensure that the handset cord is fully connected to both the phone and handset. See the
section “Connecting a Handset or Headset” in the Aastra 6753i Installation Guide for
information.
How do I find the IP address of my phone?
Instructions on where to find the IP address of your phone can be found in this guide in the section,
“Finding Your Phone’s IP Address” on page 19.
Why does my phone display the “No Service” message?
The phone displays the “No Service” message if the SIP settings have not been set up correctly.
Contact your System Administrator for more information.
How do I change my user password?
You can change the user password from the IP phone UI or the Aastra Web UI.
IP Phone UI
1. Press
on the phone to enter the Options List.
2. Select User Password and press Enter.
3. Enter the current user password and press Enter.
4. Enter the new user password and press Enter.
5. Re-enter the new user password and press Enter.
A message, "Password Changed" displays on the screen.
Troubleshooting Solutions
Aastra Web UI
1. Click on Operation->User Password.
2. In the "Current Password" field, enter the current user password.
Note: By default, the user name is “user” (all lowercase) and the password field
is left blank. If you have forgotten your password, contact your System
Administrator for assistance.
3. In the "New Password" field, enter the new user password.
4. In the "Password Confirm" field, enter the new user password again.
Model 6753i IP Phone User Guide
203
Troubleshooting Solutions
5. Click
to save your changes.
For information on how to access the Aastra Web UI, go to the section “Using the Aastra Web
UI” on page 14.
Why does my phone display "Bad Encrypted Config"?
The IP phone displays "Bad Encrypted Config" because encrypted configuration files are
enabled but the decryption process has failed.
Report this error to your System Administrator.
How do I restart the IP phone?
IP Phone UI
1. Press the
button on the phone to enter the Option List.
2. Use the 2 key to scroll down the list of options to Phone Status and press the 4. key to
select.
3. Press the 2 key to scroll to the Restart Phone option.
Press the 4. key to confirm and restart the phone. If you do not wish to restart your phone, press
the 3 key to cancel.
Note: Your phone is out of service temporarily during the restart and
downloading process.
Aastra Web UI
1. Click on Operation->Reset.
2. Click
.
3. Click OK at the confirmation prompt.
204
Model 6753i IP Phone User Guide
How do I lock my phone?
You can lock your phone to prevent the phone from being used or configured. You can lock the
phone using any of the following:
•
In the IP Phone UI at the path Options->Phone Lock.
•
In the Aastra Web UI at the path Operations->Phone Lock.
•
At a configured Phone Lock key on the phone. For more information about configuring a
Lock/Unlock key on your phone, see “Phone Lock Key” on page 104.
Use the following procedure to lock an IP phone using the IP Phone UI.
IP Phone UI
Lock the Phone
1. Press
on the phone to enter the Options List.
2. Select Phone Lock and press Enter..
3. Press 4 to set the phone to lock.
4. Press
on the phone.
The following message displays:
"Phone is locked".
1. Press
Troubleshooting Solutions
Unlock the Phone
on the phone to enter the Options List.
2. Enter your user password and press Enter.
The phone unlocks.
Use the following procedure to lock an IP Phone using the Aastra Web UI.
Aastra Web UI
1. Click on Operation->Phone Lock.
Model 6753i IP Phone User Guide
205
Troubleshooting Solutions
Lock the Phone
2. In the "Lock the Phone?" field, click
.
The phone locks dynamically and displays the following message:
"Phone is locked".
Unlock the Phone
3. Click on Operation->Phone Lock.
4. In the "Unlock the Phone?" field, click
.
The phone unlocks dynamically and displays the following message:
"Phone is unlocked".
206
Model 6753i IP Phone User Guide
Limited Warranty
Aastra Telecom warrants this product against defects and malfunctions during a one (1) year
period from the date of original purchase. If there is a defect or malfunction, Aastra Telecom
shall, at its option, and as the exclusive remedy, either repair or replace the telephone set at no
charge, if returned within the warranty period.
If replacement parts are used in making repairs, these parts may be refurbished, or may contain
refurbished materials. If it is necessary to replace the telephone set, it may be replaced with a
refurbished telephone of the same design and color. If it should become necessary to repair or
replace a defective or malfunctioning telephone set under this warranty, the provisions of this
warranty shall apply to the repaired or replaced telephone set until the expiration of ninety (90)
days from the date of pick up, or the date of shipment to you, of the repaired or replacement set, or
until the end of the original warranty period, whichever is later. Proof of the original purchase date
is to be provided with all telephone sets returned for warranty repairs.
Exclusions
Aastra Telecom does not warrant its telephone sets to be compatible with the equipment of any
particular telephone company. This warranty does not extend to damage to products resulting from
improper installation or operation, alteration, accident, neglect, abuse, misuse, fire or natural
causes such as storms or floods, after the telephone is in your possession.
Aastra Telecom shall not be liable for any incidental or consequential damages, including, but not
limited to, loss, damage or expense directly or indirectly arising from the customers use of or
inability to use this telephone, either separately or in combination with other equipment. This
paragraph, however, shall not apply to consequential damages for injury to the person in the case
of telephones used or bought for use primarily for personal, family or household purposes.
This warranty sets forth the entire liability and obligations of Aastra Telecom with respect to
breach of warranty, and the warranties set forth or limited herein are the sole warranties and are in
lieu of all other warranties, expressed or implied, including warranties or fitness for particular
purpose and merchantability.
Should the set fail during the warranty period;
In North America, please call 1-800-574-1611 for further information.
Outside North America, contact your sales representative for return instructions.
You will be responsible for shipping charges, if any. When you return this telephone for warranty
service, you must present proof of purchase.
Model 6753i IP Phone User Guide
207
Limited Warranty
Warranty Repair Services
Limited Warranty
After Warranty Service
Aastra Telecom offers ongoing repair and support for this product. This service provides repair
or replacement of your Aastra Telecom product, at Aastra Telecom's option, for a fixed charge.
You are responsible for all shipping charges. For further information and shipping instructions;
In North America, contact our service information number: 1-800-574-1611.
Outside h America, contact your sales representative.
Note: Repairs to this product may be made only by the manufacturer and its
authorized agents, or by others who are legally authorized. This restriction
applies during and after the warranty period. Unauthorized repair will void the
warranty.
208
Model 6753i IP Phone User Guide
Appendix A - Time Zone Codes
The following table identifies the time zone name and time zone code to use on the IP phone.
Time Zone Name/Time Zone Code Table
Time Zone Code
AD-Andorra
AE - Dubai
AG-Antigua
AI-Anguilla
AL-Tirane
AN-Curacao
AR-Buenos Aires
AS-Pago Pago
AT-Vienna
AU-Lord Howe
AU-Tasmania
AU-Melbourne
AU-Sydney
AU-Broken Hill
AU-Brisbane
AU-Lindeman
AU-Adelaide
AU-Darwin
AU-Perth
AW-Aruba
AZ - Baku
CET
GST
AST
AST
CET
AST
ART
BST
CET
LHS
EST
EST
EST
CST
EST
EST
CST
CST
WST
AST
AZT
BA-Sarajevo
BB-Barbados
BE-Brussels
BG-Sofia
BM-Bermuda
BO-La Paz
BR-Noronha
BR-Belem
BR-Fortaleza
BR-Recife
BR-Araguaina
BR-Maceio
BR-Sao Paulo
BR-Cuiaba
BR-Porto Velho
BR-Boa Vista
BR-Manaus
BR-Eirunepe
BR-Rio Branco
BS-Nassau
BY-Minsk
BZ-Belize
EET
AST
CET
EET
AST
BOT
FNT
BRT
BRT
BRT
BRS
BRT
BRS
AMS
AMT
AMT
AMT
ACT
ACT
EST
EET
CST
Model 6753i IP Phone User Guide
Appendix A - Time Zone Codes
Time Zone Name
A-1
Appendix A - Time Zone Codes
A-2
Time Zone Name
Time Zone Code
CA-Newfoundland
CA-Atlantic
CA-Eastern
CA-Saskatchewan
CA-Central
CA-Mountain
CA-Pacific
CA-Yukon
CH-Zurich
CK-Rarotonga
CL-Santiago
CL-Easter
CN-China
CO-Bogota
CR-Costa Rica
CU-Havana
CY-Nicosia
CZ-Prague
NST
AST
EST
EST
CST
MST
PST
PST
CET
CKS
CLS
EAS
CST
COS
CST
CST
EES
CET
DE-Berlin
DK-Copenhagen
DM-Dominica
DO-Santo Domingo
CET
CET
AST
AST
EE-Tallinn
ES-Madrid
ES-Canary
EET
CET
WET
FI-Helsinki
FJ-Fiji
FK-Stanley
FO-Faeroe
FR-Paris
EET
NZT
FKS
WET
CET
GB-London
GB-Belfast
GD-Grenada
GE - Tbilisi
GF-Cayenne
GI-Gibraltar
GP-Guadeloupe
GR-Athens
GS-South Georgia
GT-Guatemala
GU-Guam
GY-Guyana
GMT
GMT
AST
GET
GFT
CET
AST
EET
GST
CST
CST
GYT
HK-Hong Kong
HN-Tegucigalpa
HR-Zagreb
HT-Port-au-Prince
HU-Budapest
HKS
CST
CET
EST
CET
IE-Dublin
IS-Reykjavik
IT-Rome
GMT
GMT
CET
JM-Jamaica
JP-Tokyo
EST
JST
Model 6753i IP Phone User Guide
Time Zone Code
KY-Cayman
EST
LC-St Lucia
LI-Vaduz
LT-Vilnius
LU-Luxembourg
LV-Riga
AST
CET
EET
CET
EET
MC-Monaco
MD-Chisinau
MK-Skopje
MQ-Martinique
MS-Montserrat
MT-Malta
MU - Mauritius
MX-Mexico City
MX-Cancun
MX-Merida
MX-Monterrey
MX-Mazatlan
MX-Chihuahua
MX-Hermosillo
MX-Tijuana
CET
EET
CET
AST
AST
CET
MUT
CST
CST
CST
CST
MST
MST
MST
PST
NI-Managua
NL-Amsterdam
NO-Oslo
NR-Nauru
NU-Niue
NZ-Auckland
NZ-Chatham
CST
CET
CET
NRT
NUT
NZS
CHA
OM - Muscat
GST
PA-Panama
PE-Lima
PL-Warsaw
PR-Puerto Rico
PT-Lisbon
PT-Madeira
PT-Azores
PY-Asuncion
EST
PES
CET
AST
WET
WET
AZO
PYS
RO-Bucharest
RU-Kaliningrad
RU-Moscow
RU-Samara
RU-Yekaterinburg
RU-Omsk
RU-Novosibirsk
RU-Krasnoyarsk
RU-Irkutsk
RU-Yakutsk
RU-Vladivostok
RU-Sakhalin
RU-Magadan
RU-Kamchatka
RU-Anadyr
EET
EET
MSK
SAM
YEK
OMS
NOV
KRA
IRK
YAK
VLA
SAK
MAG
PET
ANA
Model 6753i IP Phone User Guide
Appendix A - Time Zone Codes
Time Zone Name
A-3
Appendix A - Time Zone Codes
A-4
Time Zone Name
Time Zone Code
SE-Stockholm
SG-Singapore
SI-Ljubljana
SK-Bratislava
SM-San Marino
SR-Paramaribo
SV-El Salvador
CET
SGT
CET
CET
CET
SRT
CST
TR-Istanbul
TT-Port of Spain
TW-Taipei
EET
AST
CST
UA-Kiev
US-Eastern
US-Central
US-Mountain
US-Pacific
US-Alaska
US-Aleutian
US-Hawaii
UY-Montevideo
EET
EST
CST
MST
PST
AKS
HAS
HST
UYS
VA-Vatican
CET
YU-Belgrade
CET
Model 6753i IP Phone User Guide
Index
Numerics
6753i
customizing 11, 23
feature 2
getting started 4
idle screens 7
incomplete configuration message 8
installation and setup 3
keys and key descriptions 9
no service message 8
plugging in the phone 4
requirements 2
A
Aastra Web UI
Basic Settings parameters 17
Operaton parameters 16
phone status 16
about this guide 1
account configuration 140
account status 21
ACD key 69
allow barge-in, for intercom 182
audio, setting 27
auto-answer, for intercom 182
autodial (hotline and warmline) 191
B
BLF key 63
BLF list 65, 68
BLF List key 65
BLF/Xfer 86
BLF/Xfer key 86
BLF/Xfer, softkeys for 87, 89, 91
C
Model 6753i IP Phone User Guide
D
DCP key 73
delete key 10
dial plan, emergency 45
dial tones, stuttered 169
dialing a number 110
dialpad, live 26
Directory key 92
directory key 93
Directory List
downloading to phone 133
directory list 124
downloading to PC 133
sorting 125
diverting calls 198
DND key 62
DND, enabling/disabling 140, 145
documentation 1
DTMF, suppressing playback 163
Index
call destination, displaying 199
Call Forward key 85
call forwarding, softkeys for 85
call waiting tone 168
callers list 134
downloading to phone 139
Callers List key 94
callers list key 94
callers list key, customizable 191
calls, ending 123
calls, handling 115
calls, making 110
calls, managing 124
calls, placing on hold 115
calls, receiving 114
calls, transferring 116
conference calls 118
Conference key 98
conference key, setting 97, 98
conferencing
ending 123
transfer remaining parties 123
conferencing, centralized 192
contrast level 26
Index-1
Index
Index
E
BLF key 63
BLF List key 65
BLF/Xfer key 86
Call Forward key 85
Callers List key 94
Conference key 98
DCP and GCP keys 73
deleting 109
descriptions of 9
Directory key 92
DND key 62
Flash key 68
Ignore key for XML 192
Intercom key 100
Last Call Return key 84
Line key 51
None key 108
Paging key 106
Park and Pickup keys 81
Phone Lock key 104
Services key 102
Speeddial key 52
Speeddial/Conf key 90
Speeddial/Xfer key 88
Sprecode key 80
Transfer key 96
XML key 77
emergency dial plan, defining 45
empty key 108
expansion module, 560M 200
expansion module, M670i 200
F
Flash key 68
G
GCP key 73
Goodbye key cancels incoming call 177
configuring 177
using 178
group RTP paging 184
H
headset mode 27
headset, using 111
headset/speaker mode 27
hold, feature enhancement using 196
I
idle screens 7
ignore sofkey 192
incoming call interrupts dialing 172
incomplete configuration 8
installation and setup, 9122i 3
intercom calls
incoming call features 181
Intercom key 100
intercom, outgoing calls using 190
Introduction 207
IP address of the phone 19
IP address, finding 19
K
key panel 9
key redirection 194
keys
ACD key 69
Answer softkey for XML 192
Index-2
L
language
latin 2 character set 40
overview 32
specifying on IP phone 32
last call return key 84
LCR key 84
Line key 51
lines settings 47
LLDP ELIN 186
lock/unlock the phone 205
locking/unlocking the phone 44
Model 6753i IP Phone User Guide
Index
M
M670i 200
message waiting indicator, configuring 180
microphone mute, for intercom 181
microphone volume, headset 27
missed call summary subscription 190
missed calls indicator
accessing and clearing 160
overview 160
N
no service 8, 203
None key 108
O
options
Aastra Web UI 14
IP Phone UI 11
simplified menu 12
P
Paging key 106
paging, softkeys for 106
Park key 81
park/pickup
using on the IP phone 83
password, resetting user’s 42
Phone Lock key 104
phone status 41
phone status, displaying 18
Pickup key 81
playing a WAV file 193
preferred line 175
preferred line timeout 175
programmable key
description 48
R
Model 6753i IP Phone User Guide
S
save key 10
Services key 102
speaker mode 27
speaker/headset mode 27
speakerphone, using 110
speeddial
configuring key for 52
configuring prefix for 52
creating from Keypad Speeddial in Web UI 57
creating from phone keypad 53
creating from programmable key in Web UI 56
creating from SAVE key 55
creating from Speeddial Edit Option 54
editing 58
saving to Redial List, Callers List, Directory List 57
speeddial/Xfer 88
Speeddial/Xfer key 88
Sprecode key 80
star codes 162
starting up the phone 4
status scroll delay 171
switch UI focus to ringing line 174
T
Transfer key 96
troubleshooting solutions 202
changing password 203
display blank 202
finding IP address 203
handset not working 202
locking/unlocking phone 205
no dial tone 202
no light for VM message 202
no ring 202
no speakerphone 202
phone displays "Bad Encrypted Config"? 204
phone displays "No Service" 203
restarting phone 204
Index-3
Index
redial 112
restarting the phone 43
ring tone sets 24
ring tones 23
RTP paging, group 184
Index
Index
U
UPnP mapping lines 179
user password 41
V
voicemail 114, 161
W
warning tone, for Intercom 182
warranty, limited 207
X
XML application title 77
XML application URI 77
XML beep support 170
XML features 193, 195
XML key 77
XML service, accessing 79
Index-4
Model 6753i IP Phone User Guide
Aastra Telecom will not accept liability for any damages and/or long distance charges, which result
from unauthorized and/or unlawful use.
While every effort has been made to ensure accuracy, Aastra Telecom will not be liable for technical
or editorial errors or omissions contained within this documentation. The information contained
in this documentation is subject to change without notice.
Copyright 2008 Aastra Telecom. www.aastra.com
All Rights Reserved.