Bock Water heaters | 40E | Product manual | Bock Water heaters 40E Product manual

40E ELECTRIC FAN HEATER
PRODUCT MANUAL
IMPORTANT
READ AND UNDERSTAND THIS MANUAL BEFORE ASSEMBLING, STARTING OR SERVICING THE HEATER.
IMPROPER USE OF HEATER CAN CAUSE SERIOUS INJURY.
KEEP THIS MANUAL FOR FUTURE REFERENCE.
FOR PROFESSIONAL USE ONLY
OCTOBER 2014 REVISION
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
IMPORTANT INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS HEATER
1. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handle when
moving this heater. Keep combustible materials at least 6 feet (2 meter) from the front of the heater and keep
them away from sides and rear
2. Extreme caution is necessary when the heater is used near children or invalids and whenever the heater is
left unattended
3. Always unplug the heater when not in use
4. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped
or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical
adjustment or repair
5. Do not expose to rain, water spray or dripping water
6. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the
heater where it may fall into a bathtub or other liquid container
7. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away
from traffic area and where it will not be tripped over
8. To disconnect heater, turn controls to off, then remove plug from outlet
9. Connect to properly grounded outlets only
10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater
11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces,
where openings may become blocked
12. A heater has hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint or flammable
liquids are used or stored
13. Do not point to flammable materials
14. Use heater only as described in this manual. Any other use not recommended by the manufacturer may
cause fire, electric shock or injury to persons
15. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable
power tap (outlet/power strip)
16. SAVE THESE INSTRUCTIONS
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
GENERAL INFORMATION FOR USER
Patron electric heaters are designed for professional use.
The heat is generated in sealed heating elements inside the inner mantle of the heater. Heated air is then distributed by an electric motor driven fan blowing air through the heater.
Although effectively cooled by the fan, the heating elements have high surface temperatures. That is why combustible materials must be kept at a safe distance from the heater and care must be taken that no combustible
particles enter the heater with the air sucked in by the fan.
Keep the heater clean of dust at any time. Dust may cause fire when heated.
Make sure that the fan blades may rotate unobstructed at all times.
Do not block air intakes or exhaust in any manner.
LIMITED WARRANTY
PATRON heater products are professional construction heaters. They are warranted for twenty-four (24) months
from original date of purchase. The warranty does not cover products modified outside our factory, damage
or failure caused by acts of God, abuse, misuse, use on other than rated voltage, abnormal usage, faulty or
improper installation, failure to provide recommended maintenance or any repairs other than those provided by
an authorized PATRON service.
THERE ARE NO OBLIGATIONS OR LIABILITIES ON THE PART OF PATRON PRODUCTS INC. FOR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF
THE PRODUCT OR OTHER INDIRECT DAMAGES WITH RESPECT TO LOSS OF PROPERTY, REVENUES,
OR PROFIT, OR COST OF REMOVAL, INSTALLATION OR REINSTALLATION.
THIS WARRANTY CONSTITUTES THE EXCLUSIVE REMEDY OF ANY PURCHASER OF EQUIPMENT
SOLD BY THE MANUFACTURER AND ITS DEALERS AND DISTRIBUTORS AND IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED.
During the warranty period, Patron Products will, at its sole option, repair or replace any defective parts or products returned, freight prepaid, to Patron Products or such other location as Patron Products may designate.
Returned products must be packaged carefully, and Patron Products shall not be responsible for damage in
transit. When returning parts, the owner must provide the model number of the product and the nature of difficulty being experienced. This warranty does not oblige Patron Products to bear the cost of labour in replacing any assembly, unit or component or part thereof, nor does the company assume any liability for secondary
charges, expenses of removal or installing, freight or damages. There will be charges rendered for product
repair after our warranty period has expired. Proof of purchase, including date, must accompany request for inwarranty service.
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
OPERATION
REVIEW AND UNDERSTAND ALL WARNINGS IN THIS MANUAL. THEY ARE ESSENTIAL FOR SAFE USE
OF THE HEATER.
FOLLOW ALL LOCAL CODES
TO START HEATING:
1. Place the heater on a stable and level surface. Make sure that no explosive or combustible fumes or dust
are present.
MINIMUM CLEARANCES FROM COMBUSTABLE MATERIALS
OUTLET = 6 feet
SIDES = 1 foot
TOP = 2 feet
REAR = 2 feet
FLOOR = COMBUSTABLE
2. Connect power cord of heater into 480 V / 60 Hz three phase power source. THE POWER SOURCE MUST
BE EQUIPPED WITH A CIRCUIT BREAKER! See paragraph “Technical specifications” in this manual for
correct amperage rating. NOTE: Check your heater to make sure it is wired for either one or three phase
use.
3. Set the room thermostat to a temperature above the ambient room temperature by turning the knob. Note!
The heater will start heating only if the thermostat “calls for heat” meaning that it is set to higher than prevailing ambient temperature
Select the power range by means of the switches marked S1, S2 and S3.
S1 “ON” = Partial output 16 kW (51,200 BU/h)
S1 & S2“ON” = Partial output 32 kW (102,400 BU/h)
S1 & S2 & S3 “ON” = Full output 40 kW (136,500 BU/h)
THE HEATER WILL NOW OPERATE AUTOMATICALLY, CONTROLLED BY THE THERMOSTATS.
TO STOP HEATING
1. Turn the main switch into position “0” standby
2. Let the fan run until it stops automatically - do not disconnect heater from power source!
3. Disconnect the power supply plug
NOTE!
THE HEATER IS EQUIPPED WITH AN OVERHEAT LIMIT SWITCH WHICH MAY CAUSE THE HEATER TO
STOP. CHECK AND REMOVE THE CAUSE FOR OVERHEATING BEFORE RESTARTING.
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
MAINTENANCE
WARNING!
NEVER SERVICE THE HEATER WHILE IT IS PLUGGED IN, RUNNING OR HOT. SEVERE BODILY INJURE
OR ELECTRIC SHOCK MAY OCCUR.
ONLY QUALIFIED PERSONS ARE ALLOWED TO OPEN HEATER FOR SERVICE. NO USER-SERVICEABLE PARTS INSIDE.
•
•
•
Keep heater clean. Use pressurized air to blow fan blades clean. Note! Use moderate pressure to avoid
damage to fan blades
Inspect heater before and after each use
The bearings of the fan motor must be lubricated according to instructions on the motor
STORAGE
When not in use, the heater must be disconnected from power source, cleaned of dust and stored in a dry
place.
TECHNICAL SPECIFICATIONS
HEAT OUTPUT
(3 STAGE SELECTOR)
AIRFLOW
ELECTRIC CONNECTION
AMPERAGE DRAW (3 Phase)
AMBIENT THERMOSTAT
LENGTH
WIDTH
HEIGHT
WEIGHT
BTU/Hr
51,200 / 102,400 / 136,500
CFM
V ac / Hz
A
1,765
480 / 60 three phase
Partial: 20
Partial: 40
Full: 50
32 - 100 °F (0 - 40 °C)
46
20
25
125
temp. range
inches
inches
inches
lbs
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
SPARE PARTS
DIAGRAM
PATRON 40E
5
4
6
Drawing 1
A
16
20
12
13
15
14
1
21
2
7
19
8
A
Dwg. 2
2
9
3
10
11
18
17
1
404103
Heat Exchange Chamber
12
404112
Fan Thermostat Plate
2
404103
Heat Exchange Chamber
13
21200
Overheat Limit Switch, Inner
3
404103
Heat Exchange Chamber
14
21100
Cooldown Thermostat
4
404102
Hood (Incl. Connection Hatch)
15
20550
Overheat Limit Switch, Air Outlet
5
404104
40E /1640E82770
CA
Connection Hatch Patron
Only
6
404101
Handle
17
74200
Wheel
7
404106
Front Panel
18
74600
Locking Washer
8
404108
Duct Adapter
19
404113
Gasket, Duct Adapter
9
404107
Bottom Frame
20
42410
Heating Element, 15 per heater
10
404111
Support Leg
21
36809
Guard Ring
11
404105
Wheel Shaft
Metal Bracket for 20550 Switch
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
SPARE PARTS
DIAGRAM
PATRON 40E
33
15
33
30
48
Drawing 2
26
25
37
30
39
42
41
38
35
34
36
31
46
48
43
41
40
47
45
27
28
29
24
Patron 40E / 40E CA / 60E
24
404115
Rear Panel
36
25
404109
Partition Panel
37
36615
Terminal Block
26
404110
Contactor Mounting Plate
38
28400
Transformer
27
404117
Fan Enclosure Tube
39
36630
Locking Clamp (2/Heater)
28
404118
Fan Mounting Plate
40
37910
Plastic Bracket
29
83900
Fan Guard Grill
41
20210
Ambient Thermostat
30
36804
Bushing, Medium
42
20212
Thermostat Knob
31
36805
Bushing, Large
43
404116
Bolt
33
22560
Contactor (4/Heater)
45
14300
Fan Motor
34
36905
Strain Reliever
46
14310
Power Cord, Fan Motor (per ft)
35
26900
Toggle Switch
47
16351
Fan Blade
48
36802
Bushing, Small
38111 + 38110
Fuse + Fuse Holder
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
40E PRODUCT MANUAL
WIRING DIAGRAM
C1 ... C3
C1/4
Contactors
Pole 4 of contactor C1 (open)
22560
S3
Toggle switch for +8kW output
26900
-
TA
Ambient Thermostat
20210
22560
TC
Cooldown thermostat
21100
C4
Contactor for fan motor
F1
Fuse
38111
TO 1
Overheat limit switch (inner)
21200
M
Fan motor
14300
TO 2
Overheat limit switch (discharge)
20550
Heating element
42410
TR
Transformer 480V/24 V, AC
28400
S1
Toggle switch for 16 kW output
26900
X1
Terminal Block
36615
S2
Toggle switch for +16kW output
26900
R1...R15
RENTQUIP USA INC. | 1-800-818-1199 | WWW.PATRONPRODUCTS.COM
PATRON PRODUCTS
A DIVISION OF RENTQUIP
1-800-818-1199
www.patronproducts.com
Download PDF