CYBEX | 629A | Owner`s manual | CYBEX 629A Owner`s manual

Cybex Arc Trainer® 620A/629A
Owner’s Manual
Cardiovascular Systems
Part Number 5620A-4 H
www.cybexinternational.com
Cybex Arc Trainer® 620A/629A
Owner’s Manual
Cardiovascular Systems
Part Number 5620A-4 H
Cybex®and the Cybex logo are registered trademarks of Cybex International, Inc.
Arc Trainer® and its mark are registered trademarks of Cybex International, Inc.
Polaris® a registered trademark of Polar.
DISCLAIMER: Cybex International, Inc. makes no representations or warranties regarding the contents of this manual. We
reserve the right to revise this document at any time or to make changes to the product described within it without notice or
obligation to notify any person of such revisions or changes.
© 2008 Cybex International, Inc. All rights reserved. Printed in United States of America.
10 Trotter Drive Medway, MA 02053 • 888-426-9239 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • techhelp@cybexintl.com • techpubs@cybexintl.com • 5620A-4 H • July 2008
About This Manual
An Owner’s Manual is shipped with each unit. To purchase additional copies of this manual or
any other Cybex manual, please do one of the following:
• fax orders to 508-533-5183 or contact Cybex Customer Service at 888-462-9239
• or contact Cybex Customer Service at 508-533-4300
Find information on the web at www.cybexinternational.com or by e-mail at
techhelp@cybexintl.com.
FCC Compliance Information
! WARNING: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception (which can be determined by
turning the equipment off and on) the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.
Page i
Cybex Arc Trainer 620A/629A Owner’s Manual
Table of Contents
Front Pages
About this Manual . . . . . . . . . . . . . . . . . . i
FCC Compliance Information . . . . . . . . . i
Table of Contents . . . . . . . . . . . . . . . . . . iii
1 Safety
Important Voltage Information . . . . . . . . .
Grounding Instructions . . . . . . . . . . . . . . .
Important Safety Instructions . . . . . . . . .
Warning Decals . . . . . . . . . . . . . . . . . . . .
Warning Decals For Units with AC
Power Kit . . . . . . . . . . . . . . . . . . . . . . . .
Caution Decals . . . . . . . . . . . . . . . . . . . .
Explanation of Symbols Used . . . . . . . . .
1-1
1-1
1-2
1-5
1-7
1-8
1-9
2 Technical Specifications
Specifications . . . . . . . . . . . . . . . . . . . . . 2-1
3 Operation
Terms and Symbols Used . . . . . . . . . . . . 3-1
Intended Use . . . . . . . . . . . . . . . . . . . . . . 3-2
Quick Operation Guide . . . . . . . . . . . . . . 3-3
Detailed Operation Guide . . . . . . . . . . . . 3-3
Stopping the Arc Trainer 620A/629A . . . 3-6
Control During Operation . . . . . . . . . . . . 3-6
Data Readouts . . . . . . . . . . . . . . . . . . . . . 3-7
Displaying Heart Rate . . . . . . . . . . . . . . . 3-8
Heart Rate LED . . . . . . . . . . . . . . . . . . . . 3-8
Use of Programs . . . . . . . . . . . . . . . . . . . 3-9
Manual Mode . . . . . . . . . . . . . . . . . . . . . . 3-10
The Workout Perrofile. . . . . . . . . . . . . . . . . 3-10
Range of Motion . . . . . . . . . . . . . . . . . . . 3-10
Hill Interval . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Weight Loss . . . . . . . . . . . . . . . . . . . . . . . 3-16
Cardio . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
Strength . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-22
Warnings . . . . . . . . . . . . . . . . . . . . . . . . .
Regular Maintenance Activities . . . . . . . .
Cleaning Your Arc Trainer 620A/629A . .
Drive Belt Maintenance . . . . . . . . . . . . . .
Lubrication . . . . . . . . . . . . . . . . . . . . . . . .
Environment . . . . . . . . . . . . . . . . . . . . . . .
Storage . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Schedule . . . . . . . . . . . . . . . . . . .
Rechargeable Battery . . . . . . . . . . . . . . .
5 Setup and Assembly
Warnings/Cautions . . . . . . . . . . . . . . . . .
Choosing and Preparing a Site . . . . . . . .
Electrical Power Requirements . . . . . . . .
Assembling the Arc Trainer
620A/629A . . . . . . . . . . . . . . . . . . . . . . .
Testing the Operation . . . . . . . . . . . . . . .
Setting Operation Options . . . . . . . . . . . .
Cybex Personal Entertainment Monitor
- Optional . . . . . . . . . . . . . . . . . . . . . .
6 Customer Service
Contacting Service . . . . . . . . . . . . . . . . .
Serial Number and Voltage . . . . . . . . . . .
Return Material Authorization (RMA). . . .
Damaged Parts . . . . . . . . . . . . . . . . . . . .
Ordering Parts . . . . . . . . . . . . . . . . . . . . .
PartList - Main Assembly . . . . . . . . . . . . .
Exploded Views - Main Assembly. . . . . . .
Parts List - Console Assembly . . . . . . . .
Exploded View - Console Assembly . . . .
Parts List - Front End Assembly . . . . . . .
Exploded View - Front End Assembly. . .
Schematic . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-2
4-3
4-5
4-5
4-5
4-6
4-7
5-1
5-1
5-2
5-2
5-9
5-10
5-11
6-1
6-1
6-2
6-3
6-3
6-4
6-5
6-12
6-13
6-14
6-15
6-17
4 Preventive Maintenance
Page iii
Cybex Arc Trainer 620A/629A Owner’s Manual
1 - Safety
IMPORTANT: Read all instructions and warnings before using the unit.
Important Voltage Information
NOTE: The power cord is available with the optional AC power kit.
! WARNING: Do not plug unit into wall outlet without an approved medical power cord.
Before plugging the power cord into an electrical outlet, verify that the voltage requirements for your
area match the voltage of the unit that you have received.
Grounding Instructions
This unit must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and
ordinances.
! DANGER: Improper connection of the
equipment grounding conductor can result
in a risk of electric shock. Check with a
qualified electrician or service provider if
you are in doubt as to whether the unit is
properly grounded. Seek a qualified
electrician to perform any modifications to
the cord or plug. Cybex is not responsible
for injuries or damages as a result of cord
or plug modification.
Make sure that the unit is connected to an
outlet having the same configuration as the
plug. Do not use a ground plug adapter to
adapt the power cord to a non-grounded
outlet.
AW-19522
115 VAC
EW600005
220 VAC
AW-19587
100 VAC
AW-19521
230 VAC
Safety
Page 1-1
Cybex Arc Trainer 620A/629A Owner’s Manual
Important Safety Instructions
(Save These Instructions)
! DANGER: To reduce the risk of electric shock, always unplug this unit from the electrical outlet
immediately after using it and before cleaning it.
! WARNING: Serious injury could occur if these precautions are not observed. To reduce the risk
of burns, fires, electric shock, or injury:
User Safety Precautions
Safety
Page 1-2
•
Keep children away. Teenagers and disabled must be supervised.Tenez les enfants éloignés. Les
adolescents et les handicapés doivent être surveilles.
•
Obtain instruction before using. Lisez les instructions avant l’utilisation.
•
Wait until foot plates come to a complete stop before dismounting. Attendre l’arret complet des
reposes pieds avant de descendre.
•
Obtain a medical exam before beginning any exercise program.
•
Stop exercising if you feel faint, dizzy, or experience pain.
•
Read and understand the Owner’s Manual and all warnings posted on the unit before using.
•
DO NOT wear loose or dangling clothing while using.
•
Keep all body parts, towels, and the like free and clear of moving parts.
•
Use the handrails for support and to maintain balance.
•
DO NOT use the unit if you exceed 400 lbs. (180 kg). This is the rated maximum user weight.
•
Replace any warning labels if damaged, worn or illegible.
•
Report any malfunctions, damage or repairs to the facility.
•
Wait until foot plates come to a complete stop before dismounting.
•
All maintenance activities shall be performed by qualified personnel. Failure to do so could result in
serious injury.
•
DISCONNECT POWER BEFORE SERVICING.
•
Moving parts. Keep hands away when in use.
•
For connection to a Medical Grade outlet only to ensure proper grounding. Rated 100-240 VAC~
50/60 Hz 0.75 A.
Cybex Arc Trainer 620A/629A Owner’s Manual
Facility Safety Precautions
•
Make sure all user and safety precautions are observed.
•
Read and understand the Owner’s Manual completely before using the unit.
•
Make sure all users are properly trained on how to use the equipment.
•
Make sure that each machine is setup and operated on a solid level surface. Do not install
equipment on an uneven surface.
•
Make sure there is enough room for safe access and operation of the equipment.
•
Perform regular maintenance checks on the equipment. Also pay close attention to all areas most
susceptible to wear, including (but not limited to) cables, pulleys, belts and grips.
•
Immediately replace worn or damaged components. If unable to immediately replace worn or
damaged components then remove from service until the repair is made.
•
Do not attempt repairs, electrical or mechanical. Seek qualified repair personnel when servicing. If
you live in the USA, contact Cybex Customer Service at 888-462-9239. If you live outside the USA,
contact Cybex Customer Service at 508-533-4300.
•
Disconnect the optional power adapter before servicing the unit.
•
Keep a repair log of all maintenance activities.
•
Use only Cybex supplied components to maintain/repair the equipment.
•
Do not use attachments unless recommended for the unit by Cybex.
•
Do not use the unit if: the unit is plugged into an optional power adapter that has a damaged
cord; (2) the unit is not working properly or (3) if the unit has been dropped or damaged. Seek
service from a qualified technician.
•
Do not use the optional power adapter in damp or wet locations.
•
EQUIPMENT not suitable for use in the presence of a FLAMMABLE ANAESTHETIC MIXTURE WITH
AIR or WITH OXYGEN OR NITROUS OXIDE.
•
Do not use the unit outdoors.
•
The 620A/629A may generate electromagnetic or other forms of interference, or it may be affected
by interference from other equipment nearby. If this is suspected, take precautions by separating
the equipment or otherwise shielding it to avoid such interference.
NOTE: It is the sole responsibility of the user/owner or facility operator to ensure that regular
maintenance is performed.
Arc Trainers containing the A/V options
•
Devices connected to Cybex equipment must comply with appropriate safety standards. This
includes but not limited to: (UL-60601, IEC/EN 60601-1) for medical equipment.
•
There must be adequate mechanical mounting of the device in all combinations
(configurations).
Safety
Page 1-3
Cybex Arc Trainer 620A/629A Owner’s Manual
Safety
Page 1-4
•
The device must be stable on the unit in all configurations.
•
Risk and leakage current of the final combinations must comply with IEC/EN 60601-1-1 and is the
responsibility of the end user to ensure compliance.
•
Electromagnetic emissions and immunity of all configurations must conform to IEC/EN 60601-1-2.
•
All added devices must have a compatible interface.
•
All devices must be used for their intended purpose.
•
Signal or mains isolation devices and additional protective earth may be needed to assure
compliance with IEC/EN 60601-1-1.
•
Do not power the entire system from a single outlet or power strip. If the unit is used with the
optional power supply, ensure that this power supply is plugged in to a separate outlet than any
connected device, to prevent exceeding the allowable leakage current of the system.
•
End user of a system shall ensure that interruption and restoration of the power supply to any
equipment or non-medical equipment of the system shall not result in a safety hazard other than
interruption or cessation of its intended function.
Cybex Arc Trainer 620A/629A Owner’s Manual
Warning Decals
Carefully read and understand the following before using the unit:
NOTE: To replace any worn or damaged decals do one of the following: Fax orders to 508-533-5183 or
contact Cybex Customer Service at 888-462-9239. If you live outside of the USA, call 508-533-4300.
Warning decals indicate a potentially hazardous situation, which, if not avoided, could result in death or
serious injury. The warning decals are shown below.
Warning decal part number
610A-349-4
Safety
Page 1-5
Cybex Arc Trainer 620A/629A Owner’s Manual
Underneath
Access Cover
Warning decal part number - DE-19592-4
SERIOUS INJURY COULD OCCUR
IF THESE PRECAUTIONS
ARE NOT OBSERVED
High voltage is present under
this shield. This shield should
only be removed by a qualified
service technician.
Keep wet items away from
inside parts.
High voltage may still be present
even if the unit is unplugged.
Shield part number
630A-316
Warning battery
DE-19586
Located on
battery bracket
Warning decal part number
DE-17155-4
WARNING
Hot flywheel! Wait until it
cools before servicing.
DE-17155-4
Safety
Page 1-6
Cybex Arc Trainer 620A/629A Owner’s Manual
Warning Decals for Units with AC Power Kit
Warning decal part number
CM000240
ПРЕДУПРЕЖДЕНИЕ
ОТКЛЮЧИТЕ
ПИТАНИЕ,
ПРЕЖДЕ ЧЕМ
ПРИСТУПАТЬ
К ОБСЛУЖИВАНИЮ.
CM000240 E
Warning decal part number
DE-19547-4
WARNING
For connection to a Medical Grade
outlet only to ensure proper grounding.
WARNING
Grade
n to a Medical
For connectio
grounding.
ensure proper
outlet only to
VAC~ 50/60Hz
Voltage: 100-240
DE-19547-4
Voltage: 100-240 VAC~
50/60Hz
0.75 Amps
1-Phase
DE-19547-4
Safety
Page 1-7
Cybex Arc Trainer 620A/629A Owner’s Manual
Caution Decal
Caution decals indicate a potentially hazardous situation, which, if not avoided, may result in minor or
moderate injury. The caution decals are shown below.
CAUTION
Moving parts.
Keep hands away
when in use.
DE-17219-4
Caution decal part number
DE-17219-4
NOTE: This decal is located on both sides of the unit in a total of two locations.
Safety
Page 1-8
Cybex Arc Trainer 620A/629A Owner’s Manual
Explanation of Symbols Used
Class II Equipment - Classifies equipment as Class II with double insulation.
BF
Type BF Applied Part - Classifies equipment as Type BF, providing protection
against electric shock.
CE - The CE (Conformitè Europèenne) mark is a European Union approval indicating
that a product complies with a European Directive.
Pause/End - Press to pause program.
Quick Start - Press to skip Program Setup Mode and enter Manual Mode.
Up Triangle - This key adjusts Time, Level or Weight up.
Down Triangle - This key adjusts Time, Level or Weight down.
Up Arrow - This key adjusts Incline up.
Down Arrow - This key adjusts Incline down.
Level Plus - This key adjusts Level up.
Level Minus - This key adjusts Level down.
Safety
Page 1-9
Cybex Arc Trainer 620A/629A Owner’s Manual
This page intentionally left blank
Safety
Page 1-10
Cybex Arc Trainer 620A/629A Owner’s Manual
2 - Technical Specifications
Specifications
Length:
Width:
Height:
Weight of Product:
Shipping Weight:
Incline Levels:
Resistance Levels:
Stride Length:
Programs:
Console Features:
Heart Rate Features:
Frame Colors:
Resistance Range:
Maximum User Weight:
Power Rating:
Other:
Options:
82” (208 cm) NOTE: When highest incline is in use the length increases to
93” (236 cm).
30” (76 cm) NOTE: Measurement is without the water bottle holder.
Width with water bottle holder and arms attached is 37” (94cm).
59” (150cm).
450 lbs. (204 kg).
475 lbs. (215 kg).
11 (Represented by 0-10% in increments of 1).
101 (Represented by 0-100% in increments of 1).
24” (61 cm) fixed length.
Quick Start plus Manual, Weight Loss, Cardio, Interval, Hill and Strength.
Upper console: Dot Matrix of program, large 1” LED display of distance,
calories, calories per hour, METS, Watts, strides per minute and heart rate.
Lower Console: LED display of resistance and dual function display of time
and incline.
Built-in wireless heart rate receiver (transmitter not included) and contact
heart rate monitoring.
Standard: White texture, black texture, metaltone gold, black chrome,
platinum sparkle.
Custom: Unlimited colors available.
0-900 watt.
400 lbs. (181 kg).
Self powered or 100 - 240 VAC~, 50/60 Hz, 0.75A, 1-phase.
Water bottle holder.
Channel and volume controls on lower switch membrane for embedded A/V
and AC power kit.
30”
(76 cm)
Water Bottle Holder
82-93” (208-236 cm)
Technical
Specifications
Page 2-1
Cybex Arc Trainer 620A/629A Owner’s Manual
This page intentionally left blank
Technical
Specifications
Page 2-2
Cybex Arc Trainer 620A/629A Owner’s Manual
3 - Operation
Read and understand all instructions and warnings prior to using the Unit. See all of the safety related
information located in chapter 1.
Terms and Symbols Used
This section lists some of the common terms and symbols used in this chapter. Other terms and
symbols are listed in this chapter as appropriate.
Dormant Mode - This occurs when the unit is plugged in, turned to the on (I) position and not in use.
The control panel will display a beating heart when the unit is in Dormant Mode.
Program Setup Mode - This begins after pressing any program key. Upon entering a program the
LEDs flash, prompting the user to adjust the appropriate settings.
Active Mode - This begins immediately after pressing the Quick Start key (Manual Mode), or after the
Program Setup Mode. The beginning of Active Mode is marked by the 3 second countdown. Active
Mode continues until you reach the end of a program or press the Pause/end key.
Quick Start - This begins by pressing the Quick Start key. Quick Start skips the Program Setup
Mode and begins immediately in Manual Mode.
Manual Mode - This begins immediately after pressing the Quick Start key or after pressing the
Manual program key. In Manual Mode you can customize your workout Resistance and Time and
enter your Weight by pressing those keys. NOTE: Manual Mode features differ from the Manual
Program. See the Manual section in this chapter.
Workout Review - This begins after pressing the Pause/end key once, at the end of a program or
when you stop striding for 25 seconds. The workout statistics accumulated during the previous
workout session will display for 20 seconds (default setting) or until Pause/end is pressed again.
NOTE: You can change the 20 second default. See Setting Operation Options in chapter 5.
Pause Mode - This begins when the you stop striding for 25 seconds or when you press Pause/end
once. While in Workout Review you can press the Quick Start key to resume your workout in Manual
Mode. The time, calories burned and other accumulated data is remembered and added to.
ST - These keys adjust Time, Level or Weight up or down.
- These keys adjust Incline higher or lower..
+ - - These keys adjust Resistance up (+) or down (-).
channel + - (optional) - These keys adjust Channel up (+) or down (-).
volume + - (optional) - These keys adjust Volume up (+) or down (-).
Operation
Page 3-1
Cybex Arc Trainer 620A/629A Owner’s Manual
Intended Use
The intended use of this exercise equipment is to aid or improve general physical fitness and exercise.
For Household or Commercial use.
620A/629A Arc Trainer
Operation
Page 3-2
Cybex Arc Trainer 620A/629A Owner’s Manual
Quick Operation Guide
NOTE: Maximum user weight is 400 lbs. (181 kg).
The following is a quick overview of the operation of the unit. For more information read Detailed
Operation Guide in this chapter. NOTE: Times specified in this chapter reflect the unit’s defaults. To
change the defaults see Setting Operation Options in chapter 5.
1. Hold the handrails to steady yourself while you step into the foot plates and begin pedaling.
2. Press any program key or press Quick Start to skip the settings and begin Manual Mode
immediately.
3. If you pressed a program key to select a program, you will now be prompted for workout Time,
Weight, and Level as appropriate. Adjust these settings with the ST arrows and press Enter to
proceed. IMPORTANT: Enter your actual weight. The Resistance + - keys calculate the proper
resistance for your weight. Your workout may feel too easy or too difficult if you do not enter your
actual weight.
4. The unit begins the workout session setting resistance to correspond to the program that you
selected.
5. Press the Resistance + - keys to change the load at any time. The right display will show the
current resistance setting.
6. Press the Incline
incline setting.
keys to change the incline at any time. The left display will show the current
7. Press the Pause/End key at any time.
! WARNING: Wait until all moving parts come to a complete stop before dismounting.
8. Wait until foot plates come to a complete stop before dismounting the unit. Hold the handrails to
steady yourself while you step off the unit.
Detailed Operation Guide
NOTE: Maximum user weight is 400 lbs. (181 kg).
1. If using the optional AC power kit, plug the power cord into a power outlet having the same
configuration as the plug. NOTE: Coil up the remainder of the power cord and place it out of the
way.
2. If using the optional AC power kit, observe that the control panel is illuminated.
3. Hold the handrails to steady yourself while you step into the pedals.
Operation
Page 3-3
Cybex Arc Trainer 620A/629A Owner’s Manual
4. You now have the option to select a program or to select Quick Start, skip Program Setup Mode,
and enter Manual Mode.
To select a program, press a program key and follow the prompts. Upon entering a program the
LEDs flash, prompting you to adjust the appropriate settings. This is referred to as Program Setup
Mode. If the Quick Start key is pressed now, all defaults for that program will be accepted. After
10 seconds, if no key has been pressed, the first default will be accepted. After another 10
seconds the second default will be accepted and so on until the last default. The program will not
enter Active Mode until you press the Enter or Quick Start key. If no key has been pressed for 20
seconds after displaying the last default, then the unit will return to the Dormant Mode.
If you press the Quick Start key instead of choosing a program, you will enter Manual Mode.
NOTE: No prompts will occur in Manual Mode. While in Manual Mode, customize your workout
Resistance and Incline and enter your Weight by pressing those keys.
IMPORTANT: Enter your actual weight. The Resistance + - keys calculate the proper resistance for
your weight. Your workout may feel to easy or too difficult if you do not enter your actual weight.
For the most accurate calorie count, you must set your correct weight before beginning your
workout (including clothing).
NOTE: Press Enter after each adjustment.
5. Depending on which program and level you selected, the resistance may begin to increase and the
incline may rise or fall.
6. Observe the four displays (See Figure 1):
The lower left display flashes the actual incline until the desired incline is reached and then reverts
to time. During your workout the time will show in the format of minutes:seconds. If your workout
exceeds sixty minutes the time format will change to minutes only.
The lower right display shows the user’s current resistance.
The top center display begins showing your program profile at the left side.
The center display shows statistics or adjustable settings. This scans (every three seconds) through
Distance, Calories, Calories per Hour, Mets, Watts and Strides Per Minute. Press the Scan key
to toggle this feature on or off.
NOTE: The charging battery LED will light only when the battery is being charged.
NOTE: Heart Rate is scanned only when you are holding the contact heart rate grips or using Polar
compatible heart rate transmitter. See Figure 1.
Operation
Page 3-4
Cybex Arc Trainer 620A/629A Owner’s Manual
Statistics or
adjustable
settings
Profile
manual
hill
interval
Heart Rate
LED
weight
loss
Pause/end
strides
minute
Cybex International, Inc. Medway, MA USA (508) 533-4300 www.Cybexinternational.com
resistance
Incline
Keys
Time
Charging LED
Channel and Volume
keys (optional)
Resistance
+ - keys
Resistance
Figure 1
7. Press the Resistance + - keys to change the load at any time. Pressing the + key will make your
workout harder. Pressing the - key will make your workout easier. The right display will show the
current level in increments of 1 from 0 to 100.
8. Press the Incline
keys to change the incline at any time. The left display will show the current
incline (only while it is adjusting), in increments of 1 from 0 to 10.
9. Press the Pause/end key at any time to stop your workout. Press Pause/end once to end your
workout and begin your Workout Review. Press Pause/end twice to clear the Workout Review and
return to Dormant Mode.
10. When you complete a program the unit begins a countdown, “3...2...1” and sounds a tone for each
count. Workout Review displays for 20 seconds (default setting) or until you press the Pause/end
key.
NOTE: Speeding up and slowing down is dependent on the user speeding up and slowing down.
! WARNING: Wait until foot plates come to a complete stop before dismounting.
11. Wait until foot plates come to a complete stop before dismounting the unit. Hold the handrails to
steady yourself while you step off the unit.
12. The unit returns to Dormant Mode or powers off. (If used with optional power adapter, returns to
Dormant Mode).
Operation
Page 3-5
Cybex Arc Trainer 620A/629A Owner’s Manual
Stopping the Arc Trainer 620A/629A
Press Pause/End once to pause your workout for 20 seconds (default setting) and to enter the
Workout Review. All workout settings and data will remain in memory for the pre-selected time. Press
the Quick Start key within the default setting to continue your workout. If the Quick Start key has
not been pressed during the 20 second pause, workout data will be cleared and the display will either
change to Dormant Mode or powers off.
Press Pause/end a second time to interrupt workout data from cycling and to change the display to
Dormant Mode.
NOTE: Speeding up and slowing down is dependent on the user speeding up and slowing down.
! WARNING: Wait until foot plates come to a complete stop before dismounting.
Emergency Dismount: Follow the steps listed below if you experience pain, feel faint or need to stop
your unit in an emergency situation:
1.
Grip handrails for support.
2.
Stop striding.
3.
Wait until the foot plates come to a complete stop.
4.
Continue holding the handrails while you step off the unit.
Presence Detect
Presence Detect uses the movement of the pedals and any input from the user (such as a key press or
heartrate) to determine your presence. If you step off the Arc or stop moving during a workout, it may
detect that you are not there. After the pre-selected waiting period “run?” will appear in the center
window for a few seconds then Presence Detect will end your workout session. If you press Quick
Start within the time selected you can resume your workout.
Control During Operation
Control keys on the display are usable during operation and may be pressed at any time to make
adjustments in level, incline or data readouts.
Changing Level - You can change the level during a programmed workout. Press the Level key to
display the current program and level status. Then press ST keys to change the level. The level will
change immediately and will continue to accumulate performance data without interruption. NOTE: If
you change the level during the Manual Mode the level and resistance will change at once.
Changing Resistance - Press the Resistance + - keys to change the load in increments of 1.
Minimum to maximum resistance is from 0-100. NOTE: During a Manual Mode or Quick Start workout
the ST keys temporarily revert to resistance keys.
Changing Incline - Press the Incline
keys to change the elevation in increments of 1 from 0-10.
The elevation rises in the shape of an arc ranging from 12 to 34.5 degrees. See Range of Motion in this
chapter.
Operation
Page 3-6
Cybex Arc Trainer 620A/629A Owner’s Manual
channel + - (optional) - These keys adjust Channel up (+) or down (-).
volume + - (optional) - These keys adjust Volume up (+) or down (-).
Changing Programs - When changing programs, your data from the previous program will transfer
only when changing from one program to manual mode. You cannot transfer data when changing from
one program to another program or from Manual Mode to a program.
Changing Workout Time - Press Time to alter the amount of time you plan to workout. You can
change Time before or during a workout. NOTE: The Max default time may limit your time. See Setting
Operation Options in chapter 5.
Changing Data Readouts - Press Scan once to continue to display a set of data. Press Scan again
and it will continually review each set of data. NOTE: The automatic scan is a feature that can be
toggled and/or turned on or off. See Setting Operation Options in chapter 5. If Scan is off, your heart
rate will still appear when a heart beat is detected.
Data Readouts
As you exercise, the Arc Trainer 620A/629A keeps track of the following data.
Distance - The total accumulated distance, in miles or kilometers, during your
workout. NOTE: Depending on the defaults you’ve chosen this measurement will
show in English or Metric.
Calories - The total accumulated calories burned during your workout. Your weight
must be correctly set before beginning your workout for this measurement to be
most accurate.
Calories Per Hour - Calculation of present workloads energy exertion in Calories
per Hour. Your weight must be correctly set before beginning your workout for this
measurement to be most accurate.
Metabolic Equivalent - Relates to the user’s energy expenditure. A MET is a basic
unit of measurement that is used to compare relative work between individuals and
activities. One MET is the amount of oxygen an individual consumes at rest. For
example two mets would be twice that amount. If an individual were working at four
METs he/she would be consuming oxygen at a rate equal to four times their resting consumption. METs can be used to compare walking on a grade with running or
even to cycling and other activities. See The Workout Profile in this chapter for more
information.
Watts - Present workload energy exertion in Watts.
strides
minute
Strides Per Minute - Your average number of strides per minute at your current
speed.
Heart Rate - Your current heart rate. Heart rate will appear when a signal is
introduced. Use either the handgrips for Contact Heart Rate or a Polar compatible
heart rate transmitter. See Heart Rate LED for a description of colors.
Operation
Page 3-7
Cybex Arc Trainer 620A/629A Owner’s Manual
To review accumulated data after a program: The display automatically cycles through your
accumulated workout data during the Workout Review for 20 seconds (default setting).
Displaying Heart Rate
In order to display your heart rate, you must either use a Polar compatible heart rate transmitter belt
(not included) or hold the handgrips to use Contact Heart Rate.
Contact Heart Rate - Hold the handgrips on the handrails until a heart rate is displayed, typically less
than thirty seconds. For best results, hold the handgrips lightly and ensure that your hands contact
both the front and back sensors of each grip. NOTE: Hold your hands as steady as possible as
movement can cause interference on the contacts.
Factors that can interfere with the heart rate signal include:
• excessive movement
• body composition
• hydration
• too loose grip
• too tight grip
• excessive dirt, powder or oil
• resting or leaning on the grips
Contaminants, such as hand lotions, oils or body powder, may come off on the contact heart rate
grips. These can reduce sensitivity and interfere with the heart rate signal. Therefore, ensure you have
clean hands when using the contact heart rate.
Polar Compatible Reception - To use this feature, a Polar compatible heart rate transmitter belt must
be worn. To view heart rate continuously, press the Scan key when the Heart LED is lit or press the
Heart key.
Heart Rate LED
When the handgrips are held the center display switches to show the heart rate in beats per minute
(BPM) if you are not scanning. For several seconds the display will show “---”. Once the actual heart
rate is determined the center window displays the BPM and the Heart LED lights up. See Figure 2. The
color of the light represents a scale of low to high target heart rate.
Operation
Page 3-8
Cybex Arc Trainer 620A/629A Owner’s Manual
NOTE: A label is on the unit to remind you what the
color represents while you are working out.
See Figure 2.
Use of Programs
! WARNING: Obtain a medical exam before beginning
any exercise program. Begin
comfortably with a lower level and
progress with higher levels as you
become acclimated.
R 165U
LE 265
HEART RATE ZONE
Blue = 0-69 beats per minute
Green = 70-93 beats per minute
Yellow = 94-120 beats per minute (FAT BURN ZONE)
Amber = 121-170 beats per minute (CARDIO ZONE)
Purple = 171 & up beats per minute
Heart LED
The color of the heart
indicates the range of
beats per minute as
shown on this decal.
Beats Per Minute
= 0-69
= 70-93
= 94-120
= 121-170
= 171 & UP
DE-17218-4 C
With the Arc Trainer 620A/629A, you may choose from
six different programs. Five of the programs provide
ten levels of difficulty for a choice of fifty different
Figure 2
preprogrammed options. You may also use Manual Mode.
With this unique combination of programs, you can tailor
your workout to achieve exactly the fitness goals you desire, including: weight loss, conditioning,
endurance or maintenance of overall health. Speed is never predetermined for you; you can change
your speed simply by changing your stride. The program choices are summarized as follows:
Quick Start
Hill Interval
Interval
Weight Loss
Cardio
Strength
Manual
hill
interval
No levels
10 levels
10 levels
10 levels
10 levels
10 levels
No levels
Skip setup and control speed, incline, and time as you go.
Control speed and time. Level dictates incline and level.
Enter time desired. Level dictates incline and level.
Enter time desired. Level dictates incline and level.
Enter time desired. Level dictates incline and level.
Enter time desired. Level dictates incline and level.
Enter time desired. Control incline and level as you go.
weight
loss
manual
Operation
Page 3-9
Cybex Arc Trainer 620A/629A Owner’s Manual
Manual Mode
Manual Mode is not a preprogrammed workout. Instead, it allows you to choose setting as you
workout. You may choose your settings according to how you feel or your endurance level. Since
you remain in control, Manual Mode may be the best choice for beginners or for those who have not
worked out in a long time.
Press the Quick Start key to workout in Manual Mode. To increase or decrease the resistance while in
Manual Mode use the Resistance + - keys. To increase or decrease the incline while in Manual Mode
use the
arrows.
When you workout in Manual Mode, be sure to include a three-to-five minute warm-up and cool-down
period. You can warm-up by setting a low resistance at zero incline and then gradually increase the
incline and resistance to the target for your workout. Reverse this process for your cool-down period,
lowering the resistance gradually and returning the incline to zero.
The Workout Profile
The Workout Profile matrix in the center of the display uses columns of lights to show the progress of
your workout. The height of the column represents METS, specifically the highest METS you reached in
that period. Each column represents 1 minute of your total workout time when in Manual Mode and 15
seconds in every other program.
NOTE: It is conceivable to have two segments of different speed and elevation combinations in the
same met range.
Range of Motion
Press the Incline
keys to change the elevation in increments of 10%. The elevation rises or lowers
in the shape of an arc ranging from 12 to 34.5 degrees (with the chord of an arc). Depending upon the
incline you choose the primary and secondary muscles trained will vary. See Figure 3.
Operation
Page 3-10
Cybex Arc Trainer 620A/629A Owner’s Manual
4"
Stride Length 2
th
2
4"
NOTE: Stride length always remains 24” (61 cm).
Stride Len
g
Figure 3
Operation
Page 3-11
Cybex Arc Trainer 620A/629A Owner’s Manual
Hill Interval
Program Overview
The Hills program is designed to give the user the experience of hiking in a hilly terrain. This program
uses intervals of moderate resistance and incline to simulate relatively flat areas and intervals of
substantially greater incline and resistance to simulate steeper grades. Likewise the two-minute work
segments are intended to tax the users capabilities, while the two-minute rest allows for recuperation
and allows for repeated work segments. See table on the next page and Figure 4.
Hills
Time Segments :30 :30 :30
Warm Up
Resistance
1
2
3
Program Level 10 20 25 30
9 20 25 30
8 15 20 25
7 15 20 25
6 15 15 20
5 15 15 20
4 10 10 15
3 10 10 15
2 10 10 10
1 10 10 10
Incline
Program Level 10
9
8
7
6
5
4
3
2
1
Operation
Page 3-12
Warm Up
1
2
3
4
3
3
3
3
3
3
3
3
3
3
3
3
2
2
2
2
2
2
3
5
4
4
3
3
3
3
3
3
3
:30
4
35
35
30
30
25
25
20
20
15
10
4
6
5
5
4
4
3
3
3
3
3
2:00 2:00 2:00 2:00 :30 :30 :30 :30
Program Segments
Cool Down
1
2
1
2
1
2
3
4
40 60 40
60 35 30 25 20
40 50 40
50 35 30 25 20
35 45 35
45 30 25 20 15
35 40 30
40 30 25 20 15
30 35 25
40 25 20 15 15
30 25 35
35 25 20 15 15
25 30 30
30 20 15 10 10
25 25 25
30 20 15 10 10
20 20 20
25 15 10 10 10
15 15 15
20 10 10 10 10
Program Segments
1
2
1
6 10
6
5 10
5
5
9
5
4
9
4
4
8
4
3
8
3
3
7
3
3
7
3
3
6
3
3
6
3
2
10
10
9
9
8
8
7
7
6
6
Cool Down
1
2
6
5
5
4
5
4
4
3
4
3
3
3
3
3
3
3
3
3
3
3
3
4
3
3
3
3
3
3
2
2
2
4
3
3
3
3
3
3
3
2
2
2
Cybex Arc Trainer 620A/629A Owner’s Manual
Resistance %
100
Hill Intervals
Profiles Show Level 10 at 12 Minutes
Incline %
10
90
9
80
8
70
7
60
6
50
5
40
4
30
3
20
2
10
1
0
Warm
Up
Program Segments
in Minutes
Cool
Down
0
Warm
Up
Program Segments
in Minutes
Cool
Down
Figure 4
Operation
Page 3-13
Cybex Arc Trainer 620A/629A Owner’s Manual
Interval
Program Overview
The Interval program utilizes a 1:2 (work:rest) ratio with the work period lasting for 30 seconds. This
allows for moderate and balanced taxation of both the aerobic and anaerobic energy systems. As such
this program is useful to those who desire improving both their aerobic and anaerobic capabilities. This
program maintains a steady incline throughout. The use of low to moderate incline ensure that the
gluteus maximus will be the prime mover. See table below and Figure 5.
Interval
Time Segments :30 :30 :30
Warm Up
Resistance
1
2
3
Program Level 10 35 45 55
9 35 40 50
8 30 40 50
7 30 35 45
6 25 35 40
5 25 30 35
4 20 25 30
3 20 25 30
2 15 20 25
1 10 15 20
Incline
Program Level 10
9
8
7
6
5
4
3
2
1
Operation
Page 3-14
:30
4
65
60
55
50
45
40
35
30
30
20
:30 :30 :30 :30
Program Segments
1
2
3
1
70 45 45 70
65 40 40 65
60 35 35 60
55 30 30 55
50 30 30 50
45 25 25 45
40 25 25 40
35 20 20 35
30 20 20 30
25 15 15 25
Warm Up
Program Segments
1
2
3
4
1
2
3
4
2
2
3
4
5
5
5
5
2
2
3
4
5
5
5
5
2
2
3
3
4
4
4
4
2
2
3
3
4
4
4
4
2
2
3
3
4
4
4
4
2
2
2
3
3
3
3
3
2
2
2
2
3
3
3
3
2
2
2
2
3
3
3
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
:30
:30
:30
:30
:30
:30
:30
2
45
40
35
30
30
25
25
20
20
15
3
45
40
35
30
30
25
25
20
20
15
1
70
65
60
55
50
45
40
35
30
25
2
45
40
35
30
30
25
25
20
20
15
3
45
40
35
30
30
25
25
20
20
15
1
70
65
60
55
50
45
40
35
30
25
2
45
40
35
30
30
25
25
20
20
15
:30 :30 :30 :30 :30
Cool Down
3
1
2
3
4
45 40 35 30 20
40 35 30 25 15
35 30 25 20 15
30 30 25 20 10
30 30 25 20 10
25 25 20 15 10
25 25 20 15 10
20 20 15 10 10
20 20 15 10
5
15 15 15 10
5
5
6
1
2
3
4
5
6
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
5
5
4
4
4
3
3
3
2
2
Cool Down
1
2
3
4
3
2
4
3
2
3
3
2
3
3
2
3
3
2
3
2
2
2
2
2
2
2
2
2
2
2
2
2
2
4
2
2
2
2
2
2
2
2
2
2
Cybex Arc Trainer 620A/629A Owner’s Manual
Intervals
Profiles Show Level 10 at 10 Minutes
(Longer workout repeats the program segment)
100
90
80
70
Resistance % 60
50
40
30
20
10
0
Warm
Up
Program
Segments
in Minutes
Cool
Down
Warm
Up
Program
Segments
in Minutes
Cool
Down
10
9
8
7
Incline %
6
5
4
3
2
1
0
Figure 5
Operation
Page 3-15
Cybex Arc Trainer 620A/629A Owner’s Manual
Weight Loss
Program Overview
The Weight Loss program is designed for low to medium intensity training that the user can sustain for
an extended period of time. It builds from a low intensity baseline to include segments of higher incline
and resistance as well as segments that use higher resistance with the baseline incline. The constant
variety provides for periods of higher expenditure and training effect without the introduction of undue
fatigue allowing the user to perform for longer periods of time. See table below and Figure 6.
Weight Loss
Time Segments
Resistance
Program Level
10
9
8
7
6
5
4
3
2
1
:30 :30
Warm Up
1
2
5 10
5 10
5 10
5
5
5
5
5
5
0
0
0
0
0
0
0
0
:30 :30 1:00 1:00 1:00 1:00 1:00 1:00 :30 :30 :30 :30
Program Segments
Cool Down
3
4
1
2
3
4
5
1
1
2
3
4
15 20 25 45 45 25 40 25 20 15 10
5
15 20 25 40 40 25 40 25 20 15 10
5
15 20 25 35 35 25 35 25 20 15 10
5
10 15 25 40 40 25 30 25 15 10
5
5
10 15 25 35 35 25 20 25 15 10
5
5
10 15 25 30 30 25 20 25 15 10
5
5
5 10
0 25 25
0 20
0 10
5
0
0
5 10
0 20 20
0 10
0 10
5
0
0
0
5
0 10 10
0
0
0
5
0
0
0
0
0
0 10 10
0
0
0
0
0
0
0
Warm Up
1
2
3
Program Level 10
4
4
4
9
4
4
4
8
3
3
3
7
3
3
3
6
3
3
3
5
3
3
3
4
2
2
2
3
2
2
2
2
2
2
2
1
2
2
2
Incline
Operation
Page 3-16
4
4
4
3
3
3
3
2
2
2
2
Program Segments
1
2
3
4
5
4
6
6
4
4
4
6
6
4
4
3
6
6
3
3
3
4
4
3
3
3
4
4
3
3
3
4
4
3
3
2
3
3
2
2
2
3
3
2
2
2
3
3
2
2
2
3
3
2
2
1
4
4
3
3
3
3
2
2
2
2
Cool Down
1
2
3
4
4
4
4
4
4
3
3
3
3
3
3
3
3
3
3
3
3
2
2
2
2
2
2
2
2
2
2
2
2
4
4
4
3
3
3
3
2
2
2
2
Cybex Arc Trainer 620A/629A Owner’s Manual
Weight Loss
Profiles Show Level 10 at 10 Minutes
100
90
80
70
Resistance %
60
50
40
30
20
10
0
Warm
Up
Program Segments
in Minutes
Cool
Down
Program Segments
in Minutes
Cool
Down
10
9
8
7
Incline %
6
5
4
3
2
1
0
Warm
Up
Figure 6
Operation
Page 3-17
Cybex Arc Trainer 620A/629A Owner’s Manual
Cardio
Program Overview
The Cardio program is designed for experienced users that desire a high intensity cardiovascular
training experience. The two-minute work interval with high resistance ensures that the aerobic energy
system is completely taxes, while the subsequent two-minute rest interval allows for recovery enabling
a repeat at the higher work rate. Additionally, a higher incline level is used during the recovery interval
to discourage blood pooling, ensuring more complete recovery. See table below and Figure 7.
Cardio
Time Segments
Operation
Page 3-18
Resistance
Program Level 10
9
8
7
6
5
4
3
2
1
:30 :30
Warm Up
1
2
30 35
25 35
25 30
20 25
15 20
15 20
10 15
5 10
0
5
0
0
:30 :30 2:00 2:00 2:00 :30 :30 :30 :30
Program Segments Cool Down
3
4
1
2
1
1
2
3
4
45 55
80
60
80 55 45 35 30
45 55
75
55
75 55 45 35 25
40 45
70
50
70 45 40 30 25
35 40
65
45
65 40 35 25 20
30 35
60
40
60 35 30 20 15
25 30
55
35
55 30 25 20 15
20 25
50
30
50 25 20 15 10
15 20
45
30
45 20 15 10
5
10 15
40
25
40 15 10
5
0
5 10
35
20
35 10
5
0
0
Incline
Program Level 10
9
8
7
6
5
4
3
2
1
Warm Up
1
2
3
3
4
5
3
3
4
3
3
4
3
3
4
3
3
3
3
3
3
2
2
2
2
2
2
2
2
2
2
2
2
4
6
5
4
4
4
3
3
3
2
2
Program Segments Cool Down
1
2
1
1
2
3
5
8
5
6
5
4
5
8
5
5
4
3
5
7
5
4
4
3
4
7
4
4
4
3
4
6
4
4
3
3
4
6
4
3
3
3
3
5
3
3
2
2
3
5
3
3
2
2
2
4
2
2
2
2
2
4
2
2
2
2
4
3
3
3
3
3
3
2
2
2
2
Cybex Arc Trainer 620A/629A Owner’s Manual
Cardio
Profiles Show Level 10 at 10 Minutes
100
90
80
70
Resistance %
60
50
40
30
20
10
0
Warm
Up
Program Segments
in Minutes
Cool
Down
Warm
Up
Program Segments
in Minutes
Cool
Down
10
9
8
7
Incline %
6
5
4
3
2
1
0
Figure 7
Operation
Page 3-19
Cybex Arc Trainer 620A/629A Owner’s Manual
Strength
Program Overview
The program is designed with the specific goal of taxing the anaerobic energy system and encouraging
maximal power development. This program uses a 1:3 (work:rest) ratio having 15-second work
periods. The work periods use high resistance settings to maximally tax their anaerobic energy system
and rest periods with very low resistance to encourage recuperation. Additionally, this program uses
high incline settings to encourage contribution for the whole leg for maximal power production. See
table below and Figure 8.
Strength
Time Segments
Resistance
Program Level 10
9
8
7
6
5
4
3
2
1
:30 :30 :30
Warm Up
1 2 3
50 65 80
50 60 75
45 60 70
45 55 70
40 50 65
35 50 60
35 45 55
35 40 50
30 40 50
30 35 45
:30 :15 :15 :15 :15 :15
Program Segments
4 1 2 3 4 1
90 100 35 35 35 100
85 95 35 35 35 95
80 90 35 35 35 90
75 85 30 30 30 85
70 80 30 30 30 80
65 75 30 30 30 75
65 70 25 25 25 70
60 65 25 25 25 65
55 60 20 20 20 60
50 55 20 20 20 55
Warm Up
Incline
1 2 3 4
Program Level 10 5 6 8 9
9 5 6 8 9
8 5 6 7 8
7 5 6 7 8
6 5 6 7 8
5 4 5 6 7
4 4 5 6 7
3 4 5 6 7
2 3 4 5 6
1 3 4 5 6
Operation
Page 3-20
:15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :15 :30 :30 :30
Cool Down
2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3
35 35 35 100 35 35 35 100 35 35 35 100 35 35 35 100 35 35 35 30 25 20
35 35 35 95 35 35 35 95 35 35 35 95 35 35 35 95 35 35 35 30 25 20
35 35 35 90 35 35 35 90 35 35 35 90 35 35 35 90 35 35 35 30 25 20
30 30 30 85 30 30 30 85 30 30 30 85 30 30 30 85 30 30 30 25 20 20
30 30 30 80 30 30 30 80 30 30 30 80 30 30 30 80 30 30 30 25 20 20
30 30 30 75 30 30 30 75 30 30 30 75 30 30 30 75 30 30 30 25 20 15
25 25 25 70 25 25 25 70 25 25 25 70 25 25 25 70 25 25 25 20 20 0
25 25 25 65 25 25 25 65 25 25 25 65 25 25 25 65 25 25 25 20 20 0
20 20 20 60 20 20 20 60 20 20 20 60 20 20 20 60 20 20 20 15 0 10
20 20 20 55 20 20 20 55 20 20 20 55 20 20 20 55 20 20 20 15 0 10
:30
4
15
15
15
15
15
10
0
0
5
5
Program Segments
Cool Down
1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 9 8 6 5
10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 9 8 6 5
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8 7 6 5
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8 7 6 5
9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 8 7 6 5
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 7 6 5 4
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 7 6 5 4
8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 8 7 6 5 4
7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 6 5 4 3
7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 7 6 5 4 3
Cybex Arc Trainer 620A/629A Owner’s Manual
Strength
Profiles Show Level 10 at 10 Minutes
(Longer workout repeats the program segment)
100
90
80
70
Resistance %
60
50
40
30
20
10
0
Warm
Up
Program Segments
in Minutes
Cool
Down
Program Segments
in Minutes
Cool
Down
10
9
8
7
Incline %
6
5
4
3
2
1
0
Warm
Up
Figure 8
Operation
Page 3-21
Cybex Arc Trainer 620A/629A Owner’s Manual
Manual
Program Overview
Manual Mode is available both through Quick Start and through the Manual program where it includes
the program time and user weight adjustment. NOTE: There is no diagram because resistance and
incline are user-controlled.
Operation
Page 3-22
Cybex Arc Trainer 620A/629A Owner’s Manual
4 - Preventive Maintenance
Warnings
All warnings and cautions listed in this chapter are as follows:
! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do
so could result in serious injury.
! WARNING: To prevent electrical shock, be sure that the unit is unplugged from the electrical
outlet before performing any cleaning or maintenance procedures.
! WARNING: Keep wet items away from inside parts of the unit. Electrical shock could occur
even if the unit is unplugged. Do not touch components on the lower board. A
charge can remain after unplugging the power cord.
! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away
from inside parts of the unit. Electrical shock could occur even if the unit is
unplugged.
! WARNING: The flywheel may be hot. Wait until it cools before servicing.
! WARNING: Battery replacement shall be performed by qualified service technician.
Regular Maintenance Activities
! WARNING: All maintenance activities shall be performed by qualified personnel. Failure to do
so could result in serious injury.
Preventive maintenance activities must be performed to maintain normal operation of your unit. keeping
a log of all maintenance actions will assist you in staying current with all preventive maintenance
activities. See Service Schedule located at the end of this chapter.
NOTE: Worn or damaged components shall be replaced immediately or the unit removed from service
until the repair is made.
NOTE: Cybex is not responsible for performing regular inspection and maintenance actions for your
unit. Instruct all personnel in equipment inspection and maintenance actions and also in
accident reporting/recording.
Preventive
Maintenance
Page 4-1
Cybex Arc Trainer 620A/629A Owner’s Manual
Cleaning Your Arc Trainer 620A/629A
! WARNING: To prevent electrical shock, be sure that the unit is unplugged from the electrical
outlet before performing any cleaning or maintenance procedures.
When cleaning your unit spray a mild cleaning agent, such as a water and dish soap solution, on a
clean cloth first and then wipe the unit with the damp cloth.
NOTE: Do not spray cleaning solution directly on the unit. Direct spraying could cause damage to the
electronics and may void the warranty.
After Each Use - Wipe up any liquid spills immediately. After each workout, use a cloth to wipe up any
remaining perspiration from the handrails and painted surfaces.
Be careful not to spill or get excessive moisture on the console and display overlays, as this might
create an electrical hazard or cause failure of the electronics.
As Needed - Vacuum any dust or dirt that might accumulate under or around the unit. Cleaning this
area should be done as often as indicated in the Service Schedule.
! WARNING: Keep wet items away from inside parts of the unit. Electrical shock could occur
even if the unit is unplugged. Do not touch components on the lower board. A
charge can remain after unplugging the power cord and turning off the unit.
To clean inside the unit, remove the four Phillips head screws securing the access cover in place. Use
a vacuum attachment or hand vacuum to clean the exposed elevation assembly and remove dirt and
debris off of internal components.
Use a dry cloth to wipe all exposed areas. Replace the access cover and secure it with the screws
when finished.
Lift the rear of the unit and roll it back from its present position so as to vacuum the floor area
underneath the unit. When finished, return the unit to its normal position.
Contact Heart Rate Grips - Contaminants, such as hand lotions, oils or body powder, may come off
on the contact heart rate grips. These can reduce sensitivity and interfere with the heart rate signal. It is
recommended that the user have clean hands when using the contact heart rate. Clean the grips using
a cloth dampened with a cleaning solution containing alcohol. The grips are the only part of the unit
you should use a cleaning solution containing alcohol.
Preventive
Maintenance
Page 4-2
Cybex Arc Trainer 620A/629A Owner’s Manual
Drive Belt Maintenance
There are two drive belts that may become loose, worn or
cracked. See Figure 1.
Primary Belt - This is the wider of the two belts.
It has grooves that keep it aligned on the large
upper pulley. Unless the unit has been serviced
and not put back together properly, it is unlikely
that the primary belt will become loose because it
is a stretch-fit belt.
Secondary Belt - This is the narrower of the two
belts. It has grooves that keep it aligned on the
flywheel’s drive pulley. It is unlikely that the
secondary belt will become loose because it is a
stretch-fit belt. Unless the unit has been worked
on and not put back together properly, it is
unlikely the tension will change.
Primary
Drive Belt
Secondary
Follow this Drive Belt Maintenance procedure to
Drive Belt
ensure that the belts are tensioned properly and
in good condition. See the Service Schedule in
this chapter for a minimum schedule for checking
the belt tension and condition. NOTE: If a belt has
cracks or appears worn, it must be replaced
Figure 1
immediately by a qualified service technician.
Tools Required
• Phillips head screwdriver
! WARNING: Disconnect the power cord before beginning this procedure. Keep wet items away
from inside parts of the unit. Electrical shock could occur even if the unit is
unplugged.
1. Read and understand this Drive Belt Maintenance section thoroughly before proceeding to
step 2.
2. Disconnect the external power source.
A. If your unit has the optional AC Power Kit, Unplug the power cord from the power outlet.
3. Remove the access cover.
A. Using a Phillips screwdriver, remove the two lower screws securing the access cover.
Preventive
Maintenance
Page 4-3
Cybex Arc Trainer 620A/629A Owner’s Manual
B. Remove the two upper screws securing the
access cover. See Figure 2.
Access
Cover
C. Remove the access cover.
! WARNING: The flywheel may be hot. Wait until it
cools before servicing.
4. Check the condition of each belt.
A. Roll each belt by pulling down on it. Examine the
condition of each belt. If a belt has cracks or
appears worn, it must be replaced immediately
by a qualified service technician.
5. Attach the access cover.
A. Using a Phillips head screwdriver, tighten the
two upper screws first (removed in step 3B).
NOTE: Do not over tighten screws.
Screw (4)
B. Tighten the two lower screws, removed in step
3A. NOTE: Do not over tighten screws. See
Figure 2.
6. Test unit for proper operation.
Preventive
Maintenance
Page 4-4
Figure 2
Cybex Arc Trainer 620A/629A Owner’s Manual
Lubrication
The Arc Trainer 620A/629A is designed with no-maintenance parts. Although there are grease fittings
on the pillow blocks, re-lubrication of the bearings is not required.
Elevation Motor Lubrication - In time the elevation motor pivot points may develop a squeak. If a
squeak is present, the unit will need to be serviced by a qualified service technician.
Environment
Static Electricity - Depending upon where you live, you may experience dry air, causing a common
experience of static electricity. This may be especially true in the winter time. You may notice a static
build-up just by walking across a carpet and then touching a metal object. The same can hold true
while working out on your unit. You may experience a shock due to the build-up of static electricity on
your body and the discharge path of the unit. If you experience this type of situation, you may want to
increase the humidity to a comfortable level through the use of a humidifier.
Humidity - The unit is designed to function normally in an environment with a relative humidity range
of 30% to 75%.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room,
sauna, indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine
could adversely affect the electronics as well as other parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient
temperature range of 50o F (10o C) to 104o F (40o C) degrees.
Storage
Humidity - The unit can be shipped and stored in an environment with a relative humidity range of
10% to 90%.
NOTE: Do not store the unit in an area of high humidity, such as in the vicinity of a steam room, sauna,
indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine could
adversely affect the electronics as well as other parts of the machine.
Temperature - The unit can be shipped and stored in an environment with an ambient temperature
range of 32o F (0o C) and 140o F (60o C) degrees.
Preventive
Maintenance
Page 4-5
Cybex Arc Trainer 620A/629A Owner’s Manual
Service Schedule
Service Schedule
NOTE: This is the minimum recommended service.
NOTE: If using optional AC Power Kit, unplug unit from wall outlet.
Date Mileage Service Initials
Determine mileage.
1. Enter Test Mode by holding
down any key for three seconds
while pedaling the unit.
2. Then press
dist
First 500 Miles
A Check drive belts for tension
& wear.
Every 5000 Miles
A Check drive belts for tension
& wear.
B Move unit and vacuum
underneath.
C Remove access cover to clean
inside - use dry cloth & vacuum.
Every 20,000 Miles
D Check elevation assembly
& replace worn parts.
E Lubricate elevation bushings.
Preventive
Maintenance
Page 4-6
Cybex Arc Trainer 620A/629A Owner’s Manual
Rechargeable Battery
The 620A/629A Arc Trainer is designed with a 12 volt Lead-Acid rechargeable battery. The battery will
recharge during regular operation of the unit. The battery will also be charged when the optional power
adapter is plugged in.
The console indicates if the battery is charging by lighting up an LED next to the text ‘charging’. The
display will indicate dashes in the incline display if this battery should ever fail to provide enough
energy. The unit will still function normally other than the disabling of the incline feature.
! WARNING: Battery replacement shall be performed by qualified service technician.
If the battery is completely discharged, the workout review will also be truncated if the user isn’t
pedaling during this time period. Contact Cybex Service to replace the battery or purchase the optional
AC adapter kit to recharge the battery. See Chapter 6.
Preventive
Maintenance
Page 4-7
Cybex Arc Trainer 620A/629A Owner’s Manual
This page intentionally left blank
Preventive
Maintenance
Page 4-8
Cybex Arc Trainer 620A/629A Owner’s Manual
5 - Setup and Assembly
Warnings/Cautions
All warnings and cautions listed in this chapter are as follows:
! WARNING: Use extreme caution when assembling the unit. Failure to do so could result in
injury.
! WARNING: A minimum of two people are required to lift, move and assemble this unit.
Always use proper lifting methods when moving heavy items.
! WARNING: Be sure that all electrical requirements are met as indicated in the specifications
at the front of the manual and at the beginning of this chapter prior to
proceeding.
! WARNING: Wait until all moving parts come to a complete stop before dismounting.
! CAUTION: A minimum of two people are required to assemble this unit.
Choosing and Preparing a Site
Before assembling the unit you must select a suitable site and have the proper electrical outlet power
available for optimum operation and safety. See the Electrical Power Requirements section (located on
the next page) for direction in locating your voltage requirements.
The area you select for the unit should be well lit and well ventilated. Locate the unit on a structurally
sound and level surface. Allow enough clearance for safe access and passage during use of the unit.
Allow a minimum of 5” (13 cm) behind the unit for the elevation to rise. If the unit is to be located above
the first floor, place it near or above major support beams. To protect the carpeting, place a 3/4” (1.9
cm) thick wood base under the unit. Be sure to use the rubber foot covers shown on page 5-7.
Humidity - The unit is designed to function normally in an environment with a relative humidity range
of 30% to 75%.
NOTE: Do not install or use the unit in an area of high humidity, such as in the vicinity of a steam room,
sauna, indoor pool or outdoors. Exposure to extensive water vapor, chlorine and/or bromine
could adversely affect the electronics as well as other parts of the machine.
Temperature - The unit is designed to function normally in an environment with an ambient
temperature range of 50o F (10o C) to 104o F (40o C) degrees.
See Chapter 4 for information regarding storage of the unit.
Setup
and Assembly
Page 5-1
Cybex Arc Trainer 620A/629A Owner’s Manual
Electrical Power Requirements
NOTE: The AC power kit is optional on the 620A/629A Arc Trainer.
Make sure that the unit is connected to an outlet having the same configuration as the plug. NOTE: Do
not use a ground plug adapter to adapt the 3-prong power cord plug to a non-grounded electrical
outlet.
NOTE: Use Cybex supplied AC power kit only. Consult an electrician if you have any questions.
Assembling the 620A/629A Arc Trainer
! WARNING: Use extreme caution when assembling the unit. Failure to do so could result in
injury.
! CAUTION: A minimum of two people are required to assemble this unit.
Tools Required
•
•
•
•
Phillips head screwdriver
Torque wrench
7/32” Allen wrench (supplied) (2)
9/16” Open-end wrench
NOTE: The words “left” and “right” denote the user’s orientation.
1. Read and understand all instructions thoroughly before assembling the unit.
NOTE: Each step number in the assembly instructions tells you what you will be doing. The lettered
steps following each step number describe the procedure required. Do not continue with step 2
until you have carefully read all of the assembly instructions.
2. Verify you have received the correct package.
A. Read the sticker on the outside of the box and verify that the model number and voltage are
what you ordered.
3. Unpack and verify the contents of the boxes.
A. Lift up and remove the cardboard sleeve that surrounds the unit.
B. Verify that you have the color that you ordered by looking at the paint.
C. If you ordered the optional AC power kit, verify that you have the correct power cord.
Setup
and Assembly
Page 5-2
Cybex Arc Trainer 620A/629A Owner’s Manual
D. Check to be sure that the following items are present. Check off ( ) each item as you find it.
See Figure 1. If any of the parts are missing contact Cybex Customer Service.
Item Qty
Part Number
1
1
Varies
2
1
Varies
3
1
PL-17209
4
2
11090-405
5
1
AW-19522
5
1
AW-19521
5
1
AW-19587
5
1
EW600005
6
1
NA
7
1
5620A-X
8
1
620A-352
9
1
600A-301
NA means Not Applicable
Description
Base with covers attached
Console/handle assembly
Water bottle holder
Foot pad (in box)
Power cord 115 VAC (optional)
Power cord 230 VAC (optional)
Power cord 100 VAC (optional)
Power cord 220 VAC (optional)
Hardware pack
Owner’s Manual
Assembly poster
Warranty sheet
#6
#7
#8
#9
#5
(Optional)
#2
#3
#4
#1
Figure 1
Setup
and Assembly
Page 5-3
Cybex Arc Trainer 620A/629A Owner’s Manual
E. Check off (
Item
10
11
12
13
14
Qty
1
4
2
4
2
) each item in the hardware pack as you find it. See Figure 2.
Part Number
YA000201
JC700422
HT552515
JS347400
BK030204
Description
Loctite
BHSCS .375-16 x 1.50
Pan HD Phil HD Self Tapping 8-16 x .75 Type WB Black
Internal Tooth Lockwasher
7/32” Allen wrench
Hardware
#10
#11
#12
#13
#14
#2
#13
#11
#12
#1
#3
#5
(Optional)
#4
Figure 2
Setup
and Assembly
Page 5-4
Cybex Arc Trainer 620A/629A Owner’s Manual
! CAUTION: A minimum of two people are required to lift, move and assemble the unit. Always
use proper lifting methods when moving heavy items.
4. Lift and move the unit
A. Carefully remove lag bolts and shipping supports.
B. With one person on each side firmly grasp each rear foot.
C. Using proper lifting methods, lift the rear feet so that the front transport wheels are able to roll
on the floor.
D. Move or roll the unit to the location where you intend to leave it.
E. Carefully lower the rear feet so that the unit is in the intended location.
5. Remove the Left and Right Front Outside Pivot Shaft Retainers and Screws.
A. Locate the left front outside pivot shaft retainer and BHSCS on main frame.
B. Using a 7/32” Allen wrench (#14) remove the left screw .375-16 x 1.00 and pivot shaft
retainer from the main frame and set aside. See Figure 3.
C. Repeat steps 5A and 5B for the right front screw and pivot shaft retainer.
PIVOT SHAFT
RETAINER
BHCSC
Figure 3
6. Attach the Console/Handle Assembly.
NOTE: If installing the Cybex Personal Entertainment Monitor Option refer to page 5-11 for installation
instructions.
A. Locate the console/handle assembly (#2), four BHSCS .375-16 x 1.50 (#11) and four
washers (#13).
B. Locate the upper display cable and plug it into the lower display cable in the main frame
assembly. See Figure 4.
NOTE: Ensure cable connectors are securely fastened.
Setup
and Assembly
Page 5-5
Cybex Arc Trainer 620A/629A Owner’s Manual
C. Place the console/handle assembly
(#2) in the correct position on the
main frame assembly. See Figure 4.
D. Attach the console/handle assembly
using the four washers (#13) and four
screws .375-16 x 1.50 (#11) as shown
in Figure 4. NOTE: Do not securely
fasten screws at this time.
NOTE: Confirm that no cables are
pinched lowering the console.
Upper
Display
Cable
#2
#13
Lower
Display
Cable
#11
Figure 4
#2
PIVOT SHAFT
RETAINER
BHSCS/
Loctite
Figure 5
E. Place the lower left console/handle assembly support (#2) in the correct position on the main
frame assembly. See Figure 5.
F. Apply a drop of loctite to threads of BHSCS .375-16 x 1.00 removed in step 5B and
place another drop of loctite into the shaft (where the BHSCS will be threaded into).
G. Reattach left pivot shaft retainer (removed in step 5B) using the BHSCS/loctite. See Figure 5.
H. Repeat steps 6E and 6F for right side.
I. Securely fasten the BHSCS attached in steps 6D and 6G using the 7/32” Allen wrench (#14)
provided. NOTE: Torque the BHSCS in Figure 5 to 150 inch pounds minimum. Ensure the
mounting plate is tight against bearing with no side play allowed.
Setup
and Assembly
Page 5-6
Cybex Arc Trainer 620A/629A Owner’s Manual
7. Attach the water bottle holder.
A. Hold the water bottle holder (#3) with two hands and gently pull outward and continue to pull
(hold open) during step 7B. See Figure 6.
B. Place the water bottle holder (#3) over the frame with the larger side outside of the frame as
shown in Figure 6.
NOTE: Water bottle holder may be placed on either side.
C. Using a Phillips head screwdriver, attach the water bottle holder (#3) to the frame with the two
8-16 x 0.75 screws (#12). See Figure 7. NOTE: Do not overtighten.
#3
#12
Figure 7
Figure 6
8. Attach the foot covers.
A. Have one person lift the unit
while a second person places
a foot cover (#4) under each
of the two back feet.
See Figure 8.
#4
Figure 8
Setup
and Assembly
Page 5-7
Cybex Arc Trainer 620A/629A Owner’s Manual
9. Level the unit.
A. Confirm that the unit is on a level surface. If it is not, use a 9/16” open-end wrench to adjust
the leveling feet up or down. See Figure 9.
Leveling Feet
Figure 9
10. Connect the optional
power cord.
Optional AC
Power Kit
NOTE: The power cord is
included in the
optional AC power
kit.
WARNING
Grade
to a Medical
For connection
grounding.
ensure proper
outlet only to
50/60Hz
VAC~
Voltage: 100-240
DE-19547-4
A. Plug the optional
power cord (#5) into
the inlet. NOTE:
Do not plug the
power cord into an
outlet at this time.
See Figure 10.
11. Visually inspect the
unit.
A. Carefully remove any
package material
from arms and rest
of unit.
#5 Optional
Figure 10
B. Carefully examine the unit to ensure that the assembly is correct and complete.
Setup
and Assembly
Page 5-8
Cybex Arc Trainer 620A/629A Owner’s Manual
! WARNING: Be sure that all electrical requirements are met as indicated in the specifications at
the front of the manual and at the beginning of this chapter prior to proceeding.
Testing the Operation
Use the following instructions to test the full resistance and incline range of the unit.
1. Plug the optional power cord into a power outlet from a grounded circuit as described under
Electrical Requirements in this chapter. NOTE: Coil up the remainder of the power cord and place
it out of the way.
2. Observe that the control panel will illuminate and be in the Dormant Mode when using the optional
power adapter.
NOTE: If you are not using the optional AC power kit, the display will not illuminate until step 4.
3. Hold the handrails to steady yourself while you step into the pedals.
4. Begin pedaling.
5. Press the Quick Start key.
6. Run the unit through its full resistance range. First press the Resistance + key until the unit
reaches its highest load (the display will show “100”). Then press the Resistance - key until the
unit reaches its lowest load; the display will show “0”. As you stride, you will feel the resistance
change.
NOTE: When the unit reaches the set incline and resistance, the displays will stop flashing and remain
steadily illuminated to indicate that the desired settings have been reached.
7. Run the unit through its full incline range. First press the Incline
key until the unit reaches its
highest incline (the display will show “10”). Then press the Incline
key until the unit reaches its
lowest incline (the display will show “0”).
! WARNING: Wait until all moving parts come to a complete stop before dismounting.
8. Press Pause/end twice to bring the incline back to its start position, end the workout review, and
return the display to Dormant Mode.
9. Wait until foot plates come to a complete stop before dismounting the unit. Hold the handrails to
steady yourself while you step off the unit.
Setup
and Assembly
Page 5-9
Cybex Arc Trainer 620A/629A Owner’s Manual
Setting Operation Options
NOTE: If using optional AC Power Kit, unplug unit from wall outlet.
1. Enter Test Mode by holding down any key for three seconds while pedaling the unit. The display
will read “SArc”.
NOTE: After changing any value, you must press Enter to save that value. When you press enter the
display will read “updt” (updated) to confirm your selection.
2. Press the Weight key to set options, change values with S and T keys and press Enter to save
your selection. Each time you press Weight the next set of data is displayed in the following order.
Unit - Choices are “Eng” (English) or “Euro” (metric) measurements. English is the default.
Scan - This turns on or off the data readout scan (unless a specific data key is pressed during a
workout). Default is on.
Def - This is the default time for time based programs if a user doesn’t re-set Time. For example, if you
press Time you can decrease or increase the set workout time up to the amount that the Max
time is set. Choices (in minutes) include: 20, 30, 40, 50 and 60. Default is 20.
Max - This is the maximum amount of time the unit can run per use. You can limit the users time or
choose “none” for unlimited time. Choices (in minutes) include: 20, 30, 40, 50, 60, 90, 120 and “none”
for no time limit. Default is 60.
Idle (or Workout Review): - This is how long the unit retains and displays your current workout data
during a pause in the workout or after a workout. Choices include: 20 seconds; 30 seconds; 40
seconds; 1 minute and 5 minutes; default is 20 seconds.
PD (Presence Detect) — This is how long the Arc will continue your workout session if the user steps
off the pedals or stops moving. Choices are between 5 and 60 seconds. Default is 5 seconds. NOTE:
See Presence Detect in Chapter 3 for further detail.
Remember: You must press Enter after changing a value for that value to be stored.
3. To exit Test Mode press the Pause/end key once.
Your unit is now ready for use. Follow the instructions in the Operation chapter to learn how to operate
the unit.
Setup
and Assembly
Page 5-10
Cybex Arc Trainer 620A/629A Owner’s Manual
! Warning: To prevent injury, this apparatus must be securely attached to the equipment in
accordance with these installation instructions.
Cybex Personal Entertainment Monitor - Optional
Tools Required
• 3 mm Allen wrench (supplied with unit)
• 7/32” Allen wrench (supplied with unit)
1. Please read instructions thoroughly before
beginning.
D
C
2. Verify the kit contents shown in Figure 11.
A. Console with monitor mount (1), 620A-220
B. Coax and power cables (1), 630A-104 (in Arc
frame)
C. Strain relief bushing (1), PP740000
D. 3 mm Allen wrench (1), BK030210
E. Poster (1), 620A-387 (not shown)
F. Warranty sheet (1), LT-20219 (not shown)
G. Cable Tie (2), EW000028
A
G
Figure 11
H
I
J
K
3. Verify the monitor kit contents shown in
Figure 12.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Monitor (1), EE000005 or EE000007
Remote control (1), EM000000
Batteries, Remote control, AAA size (2), N/A
Screws, Mounting, M4 x 0.7 x 10 mm (4),
HC692860
Washers, External Lock (4), HS047300
Washers, Flat, M4 (4), HS097600
AC/DC Adapter (1), ET300038
Power cord, 115 VAC 60 Hz. (Country
specific cords supplied with product). (1),
EW600000
Personal Entertainment Monitor Manual (1),
LT-20191
4. Installing the coax and power cables in the
console mount.
A. Lay the console mount on the Arc Trainer
as shown in Figure 13. NOTE: This will allow
easier access to route the cable assembly.
L
P
N
O
M
Figure 12
Console
Mount
Shroud
NOTE: Place cloth under console mount
to protect the shroud from damage.
Figure 13
Setup
and Assembly
Page 5-11
Cybex Arc Trainer 620A/629A Owner’s Manual
B. Locate the coax and power cables
exiting the top of the Arc frame.
C. Insert the coax and power cables
into the bottom of the console
mount until 8” (20 cm) of cable
exits the top. See Figure 14.
Coax & Power
Cables
Heart Rate
Cable
8”
(20 cm)
NOTE: Exactly 8” (20 cm) of cable must exit
the top of the monitor mount.
5. Attach the Console Assembly.
A. Locate the console assembly, four
BHSCS (Button Head Socket Cap
Screw) and four lockwashers.
B. Plug the upper display cable into
the lower display cable in the main
frame assembly. See Figure 15.
NOTE: Ensure cable connectors are
securely fastened.
C. With 8” of coax and power cables
exiting the top of the console
assembly, pull the extra coax and
power cables out of the bottom of
the main frame.
D. Attach the console assembly to
the main frame using the four
lockwashers and four BHSCS as
shown in Figure 15.
NOTE: Confirm that no cables are pinched
lowering the console.
Display Console
RJ-45
Cable
Display
Console
Cable
Console
Mount
Handle
Assembly
Opening
Coax & Power
Cables
Figure 14
Upper
Display
Cable
Console
Assembly
Coax & Power
Cables
Lower
Display
Cable
Main Frame
Assembly
BHSCS
(4)
Lockwasher
(4)
Figure 15
NOTE: Do not securely fasten screws at
this time.
Heart Rate Cable
BHSCS
6. Installing Handrail Assembly to the
Console Assembly.
A. Plug the heart rate cable connector
from the console assembly to the
heart rate connector from the
handle assembly. See Figure 16.
B. Using a 7/32” Allen wrench, attach
the two BHSCS securing the
handle assembly to the console
assembly. See Figure 16.
Setup
and Assembly
Page 5-12
C. Continue on with step 6E on page
5-6.
Console
Assembly
Figure 16
Handle
Assembly
Cybex Arc Trainer 620A/629A Owner’s Manual
7. Install monitor.
A. Locate monitor (H), four mounting screws (K), four lock washers (L) and four flat washers (M).
B. Remove the back cover from monitor (H) by pressing the bottom tabs of the cover in
and rotating out. See Figure 17.
C. Insert the power cable end of (B) through hole on left side of monitor mount. See Figure 18.
D. Insert the RJ-45 cable and the coax cable end of (B) through hole on right side of monitor
mount. See Figure 18.
(H)
Monitor
Bracket
(H)
Tab
D
D
Monitor
Mount
Back
Cover
(B)
Power
Cable
RJ-45
Cable
(M)
(B)
Coax
Cable
Tab
NOTE: Press in bottom of tabs and rotate out.
Figure 17
(L)
(K)
Figure 18
E. Using a 3 mm Allen wrench secure
the monitor bracket to the monitor
mount using the four mounting
screws (K), four lock washers (L)
and four flat washers (M).
See Figure 18.
F. Insert the power cable, coax cable
and RJ-45 cable into the monitor
as shown in Figure 19. NOTE: Use
of the CSAFE port is optional and
requires a CSAFE cable and device.
To CSAFE
Device
Power Inlet
12 VDC
Antenna/
Cable
Source
(Coax Cable)
To Fitness
Equipment
RJ-45
Figure 19
Setup
and Assembly
Page 5-13
Cybex Arc Trainer 620A/629A Owner’s Manual
G. Secure the power cable to the monitor plate using the cable tie (G). See Figure 20.
H. Install the back cover to the monitor (H). See Figure 21.
Power
Cable
(H)
Monitor
Plate
Back
Cover
Secure Cable
Tie Here
Figure 20
Figure 21
8. Plug in AC/DC Adapter and coax cables.
A. Locate the AC/DC adapter (N) supplied with the monitor and plug into the power cable
exiting the base of the Arc.
B. Plug the power cord (O) into the AC/DC adapter (N). NOTE: Power cord (O) varies
by country.
C. Thread the antenna/cable source cable (supplied at the site location) into the coax
cable exiting the base of the Arc.
9. Set up monitor for first time use.
A.
Locate the personal entertainment monitor manual (LT-20191) and follow the set up
procedure in Chapter 5.
B. Plug the power cord (O) into a wall outlet.
C. Plug headphones (not supplied) into headphone jack located at base of console.
D. Refer to Chapter 3 of the personal
entertainment monitor manual
(LT-20191) regarding use of the
channel and volume keys located
on the lower center of the Arc
console. See Figure 22.
10. Continue on with Step 7 on page 5-7.
Channel
Keys
Figure 22
Setup
and Assembly
Page 5-14
Volume
Keys
Cybex Arc Trainer 620A/629A Owner’s Manual
6 - Customer Service
Contacting Service
Hours of phone service are Monday through Friday from 8:30 a.m. to 6:00 p.m. Eastern Standard Time.
For Cybex customers living in the USA, contact Cybex Customer Service at 888-462-9239.
For Cybex customers living outside the USA, contact Cybex Customer Service at 508-533-4300 or fax
508-533-5183.
Find information on the web at www.cybexinternational.com or by e-mail at techhelp@cybexintl.com.
Serial Number and Voltage
Your serial number and voltage can be found on the front of the unit. See Figure 1.
For your convenience record your serial number and voltage below so that you will have it ready if you
call Cybex Customer Service.
Serial Number
Voltage
Serial Number
Figure 1
Customer
Service
Page 6-1
Cybex Arc Trainer 620A/629A Owner’s Manual
Return Material Authorization (RMA)
The Return Material Authorization (RMA) system outlines the procedures to follow when returning
material for replacement, repair, or credit. The system assures that returned materials are properly
handled and analyzed. Follow the following procedures carefully.
Contact your authorized Cybex dealer on all warranty-related matters. Your local Cybex dealer will
request an RMA from Cybex, if applicable. Under no circumstances will defective parts or equipment
be accepted by Cybex without proper RMA and an Automated Return Service (ARS) label.
1. Call the Customer Service hotline listed on Page 6-1 for the return of any item that is defective.
2. Provide the technician with a detailed description of the problem you are having or the defect in the
item you wish to return.
3. Provide the model and serial number. The serial number is located on the front of the unit as shown
in Figure 1. The serial number begins with a letter, for example: R09-101331100.
4. At Cybex’s discretion, the technician may request that you return the problem part(s) to Cybex for
evaluation and repair or replacement. The technician will assign you an RMA number and will send
you an ARS label. The ARS label and RMA number must be clearly displayed on the outside of the
package that contains the item(s) to be returned. Include a description of the problem, the serial
number of the unit and the name and address of the owner in the package along with the part(s).
5. Forward the package through UPS to Cybex.
Attn: Customer Service Department
Cybex International, Inc.
1975 24th Ave SW
Owatonna, MN 55060
NOTE: Merchandise returned without an RMA number on the outside of the package or shipments sent
C.O.D. will not be accepted by the Cybex receiving department.
Customer
Service
Page 6-2
Cybex Arc Trainer 620A/629A Owner’s Manual
Damaged Parts
Materials damaged in shipment should not be returned for credit. Shipping damages are the
responsibility of the carrier (UPS, Federal Express, trucking companies, etc.).
Apparent Damage - Upon receipt of your shipment, check all boxes carefully. Any damage seen with
a visual check must be noted on the freight bill and signed by the carrier’s agent. Failure to do so will
result in the carrier’s refusal to honor your damage claim. The carrier will provide you with the required
forms for filing such claims.
Concealed Damage - Damage not seen with a visual check upon receipt of a shipment but noticed
later must be reported to the carrier as soon as possible. Upon discovery of the damage, a written or
phone request to the carrier asking them to perform an inspection of the materials must be made
within ten days of the date of delivery. Keep all shipping containers and packing materials: they will be
needed as part of the inspection process. The carrier will provide you with an inspection report and the
necessary forms for filing a concealed damage claim. Concealed damage is the carrier’s responsibility.
Ordering Parts
Fax orders to 508-533-5183. To speak with a customer service representative, call 888-462-9239 (for
customers living within the USA) or 508-533-4300 (for customers outside the USA).
Customer
Service
Page 6-3
Cybex Arc Trainer 620A/629A Owner’s Manual
Main Assembly
ITEM
QTY
PART NO.
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A23
A24
A25
A26
A27
A28
A29
A30
A31
2
2
1
1
1
4
2
1
1
1
1
5
1
1
1
1
1
6
4
4
2
2
1
1
1
1
1
11090-404
11090-405
600A-200
600A-201
600A-301
600A-311
600A-331
600A-332
600A-333
600A-334
600A-335
600A-336
600A-362
610A-201
610A-202
610A-303
610A-304
610A-311
610A-342
610A-357
610A-377
610A-395
620A-200
629A-200
620A-201
620A-203
620A-204
1
1
2
2
620A-352
630A-101
630A-317
AF-16694
A32
A33
A34
A35
A36
A37
A38
1
2
2
1
2
1
4
AW-18439
CM000243
CW-17231
DE-17317
DE-17339
DE-19561
FB030244
A39
8
FB030247
A40
A41
A42
4
8
1
FC030004
FC030007
FT-17242
A43
1
FT-17243
A44
A45
A46
A47
A48
A49
A50
8
3
1
4
4
2
8
HB-17036
HC701226
HC701230
HC701234
HF540200
HG700022
HM582514
A51
A52
A53
A54
A55
A56
2
2
4
2
6
4
HN624901
HN704000
HN704901
HN704902
HS100000
HS307601
A57
4
HS307602
Customer
Service
Page 6-4
DESCRIPTION
DECAL, CYBEX
FOOT PAD
WELDMENT, LINKAGE ROD RIGHT
WELDMENT, LINKAGE ROD LEFT
WARRANTY SHEET ARC
SPACER, FLANGE
COVER, CRANK
COVER, ELEVATION MOTOR
COVER, RIGHT
COVER, LEFT
COVER, FRONT ACCESS
INSERT, COVER
LABEL, BIOSIG PATENT
FOOT PLATE ARM, LR
FOOT PLATE ARM, RR
COVER, PIVOT RH
COVER, PIVOT LH
RETAINER, PIVOT SHAFT
PIVOT PIN
TUBE, SPACER
RETAINER, PIVOT SHAFT
ASSY, ARM CRANK
MAIN FRAME 620A
MAIN FRAME 629A
C HANDLE 620A
FOOT PLATE ARM, LF
FOOT PLATE ARM, RF
REMOVER 4/07
POSTER, INSTALLATION
DRIVE FRAME ASSEMBLY
FOAM, .25 X .38
ASSY, BEARING, 1.00 INCH
PILLOW BLOCK
HARNESS, SPA FRAME
LABEL, BLANK CALIBRATION
WHEEL, TENSIONER
DECAL, LOGO ARC TRAINER
DECAL, CYBEX VORTEX
LABEL, ETL MEDICAL
BEARING, RADIAL BALL .50 ID X
1.688 OD
BEARING, RADIAL 25MM
EXTENDED RACE
TOLERANCE RING 42 (1.653) ID
TOLERANCE RING 2.047 ID
SLEEVE, ELEVATION MOUNTING,
TOP
SLEEVE, ELEVATION MOUNTING,
BOTTOM
BEARING, BALL, .750 DIAMETER
BOLT, HHCS .375-16 x 2.0
SCREW, HHCS .375-16 x 2.50
SCREW, HHCS .375-16 x 3.00
GROMMET, NYLON
LEVELING GLIDE, .375-16
SCREW, PAN HEAD PHILPIPS
10-32 x .62 BLK
LOCKNUT, .250-20 NYLON BLK ZN
HEX NUT .375-16
LOCKNUT, .375-16 NYLON
LOCKNUT, .375-16 NYLON
WASHER, NO. 10 NYLON
WASHER, FLAT .281 ID X .500 OD X
.062 T
WASHER FLAT .281 ID X 1.000 OD. X
.063 TH
ITEM
QTY
PART NO.
DESCRIPTION
A58
A59
A60
A61
2
10
4
2
HS328300
HS347700
HS427100
HT512517
A62
8
HT552512
A63
16
HT552515
A64
A65
A66
A67
A68
A69
A70
A71
A71
A72
A73
A74
2
8
2
4
2
4
8
8
24
2
4
2
HT552516
HT572512
HX-16751
PP080229
HX-17023
HX-17143
HX622815
HX700415
HX700415
HX700417
JC700422
JD623324
A75
A76
A77
A78
A79
A80
A81
A82
A83
A84
A85
A85
A85
A85
A86
A87
A88
A89
A90
A91
A92
A93
A93
A94
A94
A95
A95
A96
A96
A97
A98
A99
A100
A101
A102
A103
A104
A104
A105
A105
A106
A107
A108
A109
4
1
4
1
4
2
1
JS347400
MR-18446
PL-16535
PL-17209
PL-17279
PP080202
PP130003
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
1
1
4
4
1
1
2
2
2
2
4
1
1
1
619A-201
619A-202
AW-19521
AW-19522
AW-19587
EW600005
5620A-x*
610-349-x*
DE-17218-x*
DE-17219-x*
DE-19561
DE-19592
DE-19547-x*
610A-300
610A-390
610A-301
610A-391
610A-302
610A-392
620AK002
620AK007
610A-397
CM000240
620A-121
HS307400
HX620420
620A-122
EC-18267
610A-407
610A-409
610A-408
610A-410
HT532517
AW-19870
610AK023
630A-351
LOCKWASHER SPLIT .312
WASHER, USS .375
WASHER, SPRG .760 1.000 .136
TAP SC 10-24 X 1.00 TYPE WB PN
HD PHIL BLK
PAN HD PHIL HD SELF TAPPING,
8-16 x .50 TYPE WB
PAN HD PHIL HD SELF TAPPING,
8-16 x .75, TYPE WB BLACK
PN HD PHIL SC # 8 X .875 BLK
TAP SC NO. 10-24 X .50 PN HD PHIL
CAP, FRAME TUBE
PLUG, TUBE END 1.50 TUBE OD
PIN, SPRING .1875 x .75 LG, TYPE 420
RING RETAINING, INTERNAL, .500-168
SHCS .250-20 UNC-3A SS
BHSCS .375-16 X .75 SS, 620A ONLY
BHSCS .375-16 X .75 SS, 629A ONLY
BHSCS .375-16 X 1.00 SS
BHSCS .375-16 X 1.50
BOLT, SHOULDER .312 x 1.75
.250-20 UNC
LOCKWASHER, INT TOOTH .375
MOTOR, ELEVATION, 12 VDC
CAP, LINKAGE ROD, 2.00 OD
WATER BOTTLE HOLDER
SPACER, SHAFT, FOOT PLATE
INSERT, PLASTIC, 1.19 DIA-11 GA
INSERT, DOMED PLASTIC
REMOVED 4/07
REAR LEG RH, 629A ONLY
REAR LEG LH, 629A ONLY
POWER CORD 230 VAC (OPTIONAL)
POWER CORD 115 VAC (OPTIONAL)
POWER CORD 100 VAC (OPTIONAL)
POWER CORD 220 VAC (OPTIONAL)
OWNER’S MANUAL (NOT SHOWN)
WARNING DECAL
HEART RATE ZONE DECAL
CAUTION DECAL
ETL LABEL
SERVICE SCHEDULE & ERROR CODE
DECAL, MEDICAL INLET
RIGHT FOOT PLATE (BLACK)
RIGHT FOOT PLATE (YELLOW)
LEFT FOOT PLATE (BLACK)
LEFT FOOT PLATE (YELLOW)
TOE CAP (BLACK)
TOE CAP (YELLOW)
HEART RATE GRIP KIT W/O DRILL BITE
HEART RATE GRIP KIT W/ DRILL BITE
CAUTION DECAL (T/A OPTION ONLY)
WARNING DECAL
CONSOLE MOUNT
LOCKWASHER, INT TOOTH .250 SS
BHSCS .250-20 X 1.250 SS
CONSOLE MOUNT W/AV OPTION
BATTERY 12 VDC (NOT SHOWN)
TOP SENSOR GRIP (BLACK)
TOP SENSOR GRIP (YELLOW)
BOTTOM SENSOR GRIP (BLACK)
BOTTOM SENSOR GRIP (YELLOW)
TAP SC #6 X 1.00, TYPE 25, PPHD
HEART RATE CABLE
TOTAL ACCESS CONVERSION KIT
WEEE SYMBOL DECAL
*Language Key
1-German 2-French 3-Spanish 4-English 6-Japanese 7-Swedish 8-Russian
Cybex Arc Trainer 620A/629A Owner’s Manual
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
&2/.4!##%33#/6%2!33%-",9
+)4./!+
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
2)'(43(2/5$!33%-",9
+)4./!+
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
%,%6!4)/.-/4/2
#/6%2!33%-",9
,%&43(2/5$!33%-",9
+)4./!+
Customer
Service
Page 6-5
Cybex Arc Trainer 620A/629A Owner’s Manual
A105
A106
A96
A105
A104
A107
A93
A94
HANDLE ASSEMBLY
KIT NO. 620AK005
A104
A67
A97
A106
SEE CONSOLE
ASSEMBLY
A70
A57
A60
A81
A71
A108
A24
A100
A99
A104
A71
A106
A67
A105
A72
A67
A21
A21
A72
A102
A78
A75
A73
A63
Customer
Service
Page 6-6
A101
A59
A74
A53
A23
A42
A46
A43
A76
A70
A49
A52
A56
A6
A80
A77
A51
A53
A34
A58
A59
A54
A109
A77
A69
A4
A52
A51
A34
A7
A40
A36
A38
A49
A50
SERIAL
NUMBER
DECAL
A70
A81
A56
A6
KIT NO. 600AK012
A13
A37
A98
A58
A74
A59
A47
A22
A59
A45
A31
A33
A45
A54
A68
KIT NO. 600AK006
A29
A68
A22
A59
A59
A45
A31
A59
A47
A40
A7
A3
A38
A6
A69
A77
A56
A70
KIT NO. 600AK007
A50
A36
Cybex Arc Trainer 620A/629A Owner’s Manual
Customer
Service
Page 6-7
Cybex Arc Trainer 620A/629A Owner’s Manual
+)4./!+
!
!
!
!
!
!
!
!
!
!
!
!
!
,%&4&//40,!4%!33%-",9
!
!
2)'(4&//40,!4%!33%-",9
+)4./!+
!
!
!
!
!
!
!
!
!
!
!
!
Customer
Service
Page 6-8
!
Cybex Arc Trainer 620A/629A Owner’s Manual
!
RIGHT SIDE ASSEMBLY
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
+)4./
!+
!
!
+)4./!+
!
!
!
!
!
+)4./!+
!
!
!
!
!
!
+)4./!+
!
!
!
!
Customer
Service
Page 6-9
Cybex Arc Trainer 620A/629A Owner’s Manual
LEFT SIDE ASSEMBLY
A23
A97
A71
A17
A1
A71
A50
A66
A84
A71
A18
A18
A71
A19
A23
KIT NO. 610AK010
A21
A72
A39
A89
A41
A41
A39
A20
A70
A77
A20
A39
A69
A41
A40
A41
A56
A14
A39
A6
A38
A25
KIT NO. 600AK006
A70
A56
KIT NO. 620AK003
A77
A6
Customer
Service
Page 6-10
KIT NO. 600AK012
Cybex Arc Trainer 620A/629A Owner’s Manual
NOTE: Parts lists and exploded views of the console and front end assembly are on
the pages that follow.
Customer
Service
Page 6-11
Customer
Service
Page 6-12
CONSOLE
TAPE DOUBLE COATED .75
CABLE, CHR CHASSIS GND
DECAL, CSAFE PORT, ENGLISH
DECAL, ERROR CODES, ENGLISH
PLATE, CONSOLE MOUNTING
SENSOR, WIRELESS HR RECEIVER
PCA, DISPLAY BOARD, ARC
HARNESS, SPA FRAME
CABLE, 630A CHR CONSOLE
SCREW, SEMS, 10-32 X .75 PHIL PAN, BLK ZINC
LOCKWASHER EXT TOOTH NO. 8 ZINC
SCREW, TAP 8-16 x .31 PLASTITE
PAN HD PHIL HD SELF TAPPING, 8-16 x .50 TYPE WB
PAN HD PHIL HD SELF TAPPING, 8-16 x .75, TYPE WB BLK
INSERT, PLASTIC .437 DIA 11 GA
CONSOLE, FRONT PLASTIC
CONSOLE, REAR PLASTIC
COVER, CONSOLE BATTERY DOOR
TAB, BOOK HOLDER
MEMBRANE,610A TOP, UNIV
MEMBRANE, 620/630A W/O AV
630A-111-x*
01250
610A-104
610A-354-x*
610A-355-x*
610A-396
630A-318
AD-19140
AW-18440
AW-19328
HJ582515
HS087300
HT552509
HT552512
HT552515
PP080207
PP620003
PP620004
PP620005
PP620006
SW-18276-x*
SW-19296-x*
B
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
1
1
1
1
1
1
1
1
1
1
1
1
7
4
4
1
1
1
1
2
1
1
DESCRIPTION
ITEM QTY PART NO.
Console Assembly
Cybex Arc Trainer 620A/629A Owner’s Manual
B20
B16
#20
B19
B21
B1
B15
B6
B7
B12
B12
B13
B9
B12
B8
Console Assembly
B13
B11
B3
B2
B13
B14
B17
B14
B4
B18
B10
Cybex Arc Trainer 620A/629A Owner’s Manual
Customer
Service
Page 6-13
Customer
Service
Page 6-14
630A-200
630A-201
630A-305
630A-314
630A-316
600A-313
630A-328
600A-337
600A-340
600A-343
01250
AD-18442
AF-19518
1
1
2
1
1
1
1
1
2
1
2
1
1
1
2
1
1
1
1
2
1
2
2
4
4
2
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
C16
C17
C18
C19
C20
C21
C22
C23
C24
C25
C26
AX-19550
BR030221
DE-17155-x*
DE-19586
DE-19593-x*
EC-18267
FB030243
FM-16859
FM-19507
HC661240
HC661217
HC701254
HF540201
PART NO.
QTY
ITEM
FRAME, FRONT
BRACKET, TRANSFORMER (A/C OPTION
ONLY)
SPACER, INSULATING
CLAMP, BATTERY
CONTROLLER COVER
SHAFT
BELT, SECONDARY DRIVE, 7 RIB
PULLY, POLY-V DIE CAST, 16 GROOVES
BEARING, 1.00 INCH PILLOW BLOCK
BELT, PRIMARY DRIVE 16 RIB
DOUBLE SIDED FOAM TAPE, 0.75 (A/C
OPTION ONLY)
PCA, CONTROL BOARD
PLATE, POWER INLET, BLANK (FOR
CORDLESS UNITS ONLY)
ASSEMBLY, BRAKE GENERATOR
RING RETAINING, EXTERIOR CRESENT
WARNING DECAL
DECAL, WARNING ICON, BATTERY
DECAL, LOWER CONTROL COVER
BATTERY, 12 VDC
BEARING, 25 MM ID X 52 MM OD 6205
SHAFT, LOWER
COUNTERWEIGHT, PULLEY
SCREW, HEX HEAD CAP .312-18 X 3.75
HX HD CAP SCREW .312-18 X 1.00
HX HD CAP SCREW .375-16 X 5.50
NUT, GROMMET, SPACER
DESCRIPTION
HX-17023
HX-17050
630A-327
HX-19504
JC700922
JC702820
PW-16521
TR-18448
630A-315
AW-18447
CM000243
2
2
4
1
1
4
1
1
1
1
1
C35
C36
C37
C38
C39
C40
C41
C42
C43
C44
C45
HF579000
HN704901
HS307600
HS308300
HS347600
HS347700
HS760100
HT572512
4
4
2
2
4
8
4
11
C27
C28
C29
C30
C31
C32
C33
C34
PART NO.
QTY
ITEM
Front End Assembly
NUT, U TYPE 10-24 PANEL
LOCKNUT, .375-16 NYLON
WASHER, SAE .250
LOCKWASHER SPLIT .250
WASHER, SAE .375
WASHER, USS .375
SPRING RETAINING WASHER
SCREW, TAP NO. 10 - 24 X .50 PAN
HEAD
PIN, SPRING .1875 X .75 LG TYPE 420
BUSHING, 1.275 ID X 1.87 OD, NYLON
SLEEVE, GENERATOR ISOLATION
SPACER, GENERATOR ISOLATION
SCREW, FHSCS .375-16 X 1.50
SCREW, SOC HD CAP .375 X 16 X 1-1/4
PULLEY, DRIVE
TRANSFORMER, 24V DC IEC-320 INPUT
(A/C OPTION ONLY)
PLATE
BATTERY CABLE (NOT SHOWN)
LABEL, CALIBRATION
DESCRIPTION
Cybex Arc Trainer 620A-629A Owner’s Manual
C42
C2
C34
C32
C28
C32
C28
C11
C13
C1
A/C Option Only
C27
C19
C27
C27
C45
C36
C26
C22
C34
C15
C29
C23
C43
C36
C39
C30
C4
C34
C16
C17
C20
C21
C24
C27
C33
C34
C12
C9
C34
C7
C20
C41
C15
C10
C8
C35
C32
C6
C34
C5
C32
C25
C18
C25
C22
C14
C3
C39
C38
C3
C31
C37
Front End Assembly
C40
Cybex Arc Trainer 620A/629A Owner’s Manual
Customer
Service
Page 6-15
Cybex Arc Trainer 620A/629A Owner’s Manual
This page intentionally left blank
Customer
Service
Page 6-16
Cybex Arc Trainer 620A/629A Owner’s Manual
ADAPTER, SERVICE PROGRAMMING
CN-16924
5
6
7
8
GRAY
BROWN
YELLOW
GREEN
RED
BLACK
ORANGE
BLUE
BAT +
BAT -
POT HIGH
POT WIPER
POT LOW
MOTOR +
+
MOTOR -
J102
9
OPT
6310A-031
6310A-033
6310A-034
6310A-035
AW-18447
CABLE, SPA 12V BATTERY
BATTERY ON
NC
POT HIGH
J4
RXD
TXD
N/C
N/C
GND
N/C
OPTION
NOT FOR
MEDICAL
APPLICATIONS
4
3
1
8
6
7
10
4
1
2
6
3
1
CSAFE
(COMM. ONLY)
6
4
2
9
J5
5
3
2
10
8
5
1
9
7
6
4
2
P3
AW-19323
5
3
2
5
P5
A/V MONITOR
EE000004
BLACK
BROWN OR RED
4
2
2
3
1
1
7
5
3
4
6
WHITE/BLACK
10
J1
13
11
8
AW-18439
CABLE, 630A FRAME HARNESS
WHITE
WHITE/RED
WHITE/YEL
9
WHITE/ORG
RED
BLACK
ORANGE
BLUE
S
AW-19870
CABLE, CHR GRIP
VIOLET
BLACK
BRN OR RED
R COMMON (INSIDE)
GREEN
BROWN
N
12
14
630A-318 ASSY, POLAR EMBEDDED
1 CRPM = 15.15 FLYWHEEL RPM
1:15.15
P1
14
WHITE
WHITE/RED
WHITE/YLW
RED
13
12
WHITE/BLACK
10
WHITE/ORG
8
ORANGE
VIOLET
GREEN
11
9
6
4
GRAY
YELLOW
7
5
3
1
BLACK
2
3
BLUE
4
2
1
BROWN
AW-19328
2
3
1
J3
1
6
2
SW-19295-X
MEMBRANE, AARC BTM W/AV
1
2
3
2
4
6
8
7
5
2
3
1
GND
J1
3
1
SIG
J10
BAT CNTRL
N/C
N/C
N/C
POT WIPER
5
3
RED
1
BROWN
P10
HA-20175
HEADPHONES
5 X 5 UPPER MEMBRANE SWITCHES
J4
1 x 11 EMBEDDED LEDs
J3
3 x 4 LOWER MEMBRANE
ES000001
ADAPTER, 1/4"-1/8"
630A-102
CABLE, AUDIO 1/4"
POLAR
OPTION
NOT FOR
MEDICAL
APPLICATIONS
4
3
3
CHASSIS
GND
N/C
ELEV DOWN
B+
ELEV UP
TXD
POT REF
RXD
GND
RELAY +9V
RPM
2
J8
6
BRAKE
+9V PWR
LEFT
RIGHT
GND
GND
GND
TXD
RXD
LEFT
5
8
J8
4
2
1
7
COM
10
9
6
COM
7
5
5
GND
+5
SIG
8
6
4
3
4
2
1
J6
3
J2
6
5
2
ORANGE
SHIELD
LEFT COMMON
LEFT SIGNAL
SHIELD
RIGHT COMMON
RIGHT SIGNAL
3
1
BLACK
J1
4
2
1
SW-19296-4 (ENGLISH ONLY)
MEMBRANE, AARC BTM W/O AV
CHASSIS
P8
10
9
3
RIGHT
7
2
AD-19140
PCA, SPA 2-LAYER DISPLAY BOARD
EC-19141
CODE, SPA
5
1
610A-104
CABLE, CHR GND
8
6
4
3
1
630A-103 CABLE,
5E BONDED-PAIR RJ45
SW-18276-X
MEMBRANE, AARC TOP
2
P6
EW600005 (Ger. Sp. Swe.)
CABLE, POWER CORD, 230V,
10A, CEE 7-7,2M
AW-19521
POWER CORD, JAPAN,
2.4M IEC-320
AW-19587
POWER CORD, 250VAC,
3A, 2.5M IEC-320, UK
AW-18440
CABLE, 630A CONSOLE HARNESS
VCC
N
BF APPLIED PART
R SIGNAL (OUT)
630A-104
CABLE, A/V I/O W/2.1mm
AC POWER ADAPTER
GRAY
L COMMON (INSIDE)
YELLOW
S
L SIGNAL (OUT)
POWER CORD, US 10A / 125VAC MEDICAL
POWER CORD, 6A IEC-320 SCHUKO 50Hz
POWER CORD, UK IEC-320 230V
POWER CORD, JAPAN IEC-320 100v
8
1
AD-18442
CONTROLLER, SPA
AW-19522
EW600005
AW-19521
AW-19587
7
POT WIPER
N/C
N/C
BRAKE
AW-19870
CABLE, CHR GRIP
c
2.1mm
ELEV UP
TSEL
UL60601
EN60601
J6
PWM GND
VCC
+
6
QSEL
-
5
DSEL
GND
4
UP
DOWN
DISPLAY CHASSIS GND
PWM
100-240VAC
50/60Hz
24V DC
24VDC
2.5A / 250V FB
(BATTERY PWR)
F5
LOGIC GND
VDD
12V
0.75A / 24V PTC
RESETTABLE
(VDD TO DISPLAY)
F2
3
J2
GENERATOR
AC INPUT
AC INPUT
AC INPUT
RPM
15A / 125V FB
(INCLINE MOTOR)
F1
1
2
ELEV DOWN
1
+9V
2
BRAKE
3
RPM
4
J3
150°C
DE-19547-4
DECAL, POWER INLET RATING
TR-18448
TRANSFORMER, 24V DC
2
DC RETURN
JST B6P-VH
AX-19550
ECB W/GENERATOR
1
DIAGNOSTIC LEDS
1.6 / 250V FB
(BRAKE CURRENT)
1 2 3 4 5 6
2
KIT
110V/60HZ
630AX031
230V/50HZ NON UK 630AX033
230V/50HZ UK
630AX034
110V/50HZ JAPAN
630AX035
1
1 2 3 4 5 6
F6
5
6
4A / 250V FB
(GEN POWER)
1
RXD
F4
DOTTED LINES INDICATE ISOLATION
=>3000VAC
2
J8
J7
4A / 250V FB
(GEN POWER)
3
TXD
F3
4
+9V
5
6
CHASSIS
GND
N/C
B+
TXD
RXD
N/C
N/C
CSAFE CONNECTOR
ELV-MOTOR
8
5
1 CD CARRIER DETECT
2 RD RECEIVE DATA
3 TD TRANSMIT DATA
4 DTR READY
5 GND
6 DSR DATA SET READY
7 RTS REQUEST TO SEND
8 CTS CLEAR TO SEND
9 RI RING DETECT
POSITION
FEEDBACK
12v DC
7
4
4
6
EC-18267
BATTERY, 12V / 7AHR
3
3
2
2
1
1
MR-18446
GEARMOTOR,SP ARC 12V DC
STD CSAFE
EXTERNAL ACCESS
FITNESS EQUIPMENT STANDARD ONLY
SCHEMATIC INTENDED TO BE AN ELECTRICAL
REPRESENTATION OF THE ARC SYSTEM.
MECHANICAL IMPLEMENTATION OR REPRESENTATION
MAY VARY.
TO CHR BOARD
Customer
Service
Page 6-17
10 Trotter Drive Medway, MA 02053 • 508-533-4300 • FAX 508-533-5183
www.cybexinternational.com • Techhelp@cybexintl.com•techpubs@cybexintl.com
Download PDF

advertising