ViewSonic BRILLIANTCOLOR PJD6241 User guide

ViewSonic
®
PJD6241
DLP Projector
- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
- Руководство пользователя
- 使用手冊 (繁體)
- 使用手冊 (簡體)
IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for
future service. Warranty information contained in this User Guide will describe your
- 사용자 안내서
- คู่มือการใช้งาน
limited coverage from ViewSonic Corporation, which is also found on our web site
at http://www.viewsonic.com in English, or in specific languages using the Regional
- Podręcznik użytkownika
selection box in the upper right corner of our website.
“Antes de operar su equipo lea cuidadosamente las instrucciones en este manual”
- Kullanιcι kιlavuzu
Model No. : VS12476
Downloaded From projector-manual.com Viewsonic Manuals
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
For Canada
•
•
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent or
discarded batteries or accumulators as unsorted municipal waste, but use the return and
collection systems available.
If the batteries, accumulators and button cells included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of
more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
Downloaded From projector-manual.com Viewsonic Manuals
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. o not block any ventilation openings. Install the unit in accordance with the
D
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade and the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure that the
power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the unit. When a cart is used, use caution when
moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the unit
has been damaged in any way, such as: if the power-supply cord or plug is damaged,
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or
moisture, or if the unit does not operate normally or has been dropped.
Downloaded From projector-manual.com Viewsonic Manuals
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the
European Parliament and the Council on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum
concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
Substance
Certain components of products as stated above are exempted under the Annex of the RoHS Directives
as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not
specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic
parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up
to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.
EN-1
Downloaded From projector-manual.com Viewsonic Manuals
Copyright Information
Copyright© ViewSonic® Corporation, 2010. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please
register your product on the Internet at: www.viewsonic.com. The ViewSonic® Wizard CD-ROM also
provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJD6241
ViewSonic DLP Projector
VS12476
PJD6241_UG_ENG Rev. 1C 01-01-10
_______________________________
_______________________________
The lamp in this product contains mercury.
Please dispose of in accordance with local, state or federal laws.
EN-2
Downloaded From projector-manual.com Viewsonic Manuals
Notes on the AC Power Cord
AC Power Cord must meet the requirement of countries where you use this projector.
Please confirm your AC plug type with the graphics below and ensure that the proper
AC Power Cord is used. If the supplied AC Power Cord does not match your AC outlet,
please contact your sales dealer. This projector is equipped with a grounding type AC
line plug. Please ensure that your outlet fits the plug. Do not defeat the safety purpose
of this grounding type plug. We highly recommend using a video source device also
equipped with a grounding type AC line plug to prevent signal interference due to
voltage fluctuations.
Ground
EN-3
Downloaded From projector-manual.com Viewsonic Manuals
CONTENTS
Introduction ........................................................................................................5
Projector Features ....................................................................................................... 5
Package Contents ....................................................................................................... 6
Projector Overview ...................................................................................................... 7
Using the Product ........................................................................................ 9
Control Panel .............................................................................................................. 9
Connection Ports ....................................................................................................... 10
Remote Control .........................................................................................................11
Installing the Batteries ...............................................................................................12
Remote Control Operation ........................................................................................13
Installation ........................................................................................................14
Connecting the Projector ...........................................................................................14
Powering On/Off the Projector .................................................................................. 15
Adjusting the Projector ..............................................................................................16
Menu Operation ............................................................................................18
Network Control ......................................................................................... 25
Maintenance .................................................................................................. 40
Cleaning the Lens .....................................................................................................40
Cleaning the Projector Housing ................................................................................40
Replacing the Lamp ..................................................................................................41
Specifications ...............................................................................................43
Appendix ........................................................................................................... 44
LED Indicator Messages ...........................................................................................44
Compatibility Modes ..................................................................................................45
Troubleshooting ........................................................................................................47
RS-232 Command and Configuration .......................................................................48
IR Control Code ........................................................................................................50
EN-4 From projector-manual.com Viewsonic Manuals
Downloaded
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
„
„
„
Single chip 1.397cm / 0.55" Texas Instruments DLP® technology
XGA (1024 x 768 pixels)
Auto image re-sizing (Auto-Sync.) to 1024 x 768 full screen with scaling
compression compatibility for VGA, SVGA, XGA and SXGA
„
„
„
„
„
„
„
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
RJ-45 connector for networked control
„
„
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
EN-5
Downloaded From projector-manual.com Viewsonic Manuals
Package Contents
When you unpack the projector, make sure you have all these components:
Projector with Lens Cap
AC Power Cord
Projector Carrying Case
VGA Cable (D-SUB to DSUB)
Remote Control (IR) & batteries
ViewSonic CD
Wizard
Quick Start
Guide
Optional accessories
RS232 cable
P/N: J2552-0208-00
„
„
RGB to component adapter
P/N: J2552-0212-00
Contact you dealer immediately if any items are missing, appear damaged, or if
the unit does not work.
Save the original shipping carton and Packing material; they will come-in handy
if you ever to ship your unit. for maximum protection, repack your unit as it was
originally packed at the factory.
EN-6
Downloaded From projector-manual.com Viewsonic Manuals
Projector Overview
Front View
1
11
10 9 8 7
2 3
4 5
6
1
Lens cap
7
Speaker
2
Elevator button
8
Focus ring
3
Lens cap strap
9
Zoom ring
4
Projection lens
10
Control panel
5
Front IR remote control sensor
11
Lamp cover
6
Ventilation holes (intake)
EN-7
Downloaded From projector-manual.com Viewsonic Manuals
Rear View
1
2
3 4
5
6
1
2
3
2
4
5
6
Connection ports
AC power socket
Kensington lock
Rear IR remote control sensor
Ventilation holes (exhaust)
Security bar
143.0mm
Bottom View
1
2
70.0mm
1
2
90.0mm
Ceiling mount (M4*6)
Tilt-adjustment feet
„
„
This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
Contact your dealer for information to mount the projector on a ceiling.
EN-8
Downloaded From projector-manual.com Viewsonic Manuals
Using the Product
Control Panel
LED
9 1
2
3
4
5
6
8
7
1
2
3
4
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
Button Function
4
5
6
7
8
9
/
Keystone
Manually correct distorted images resulting from an angled projection.
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
ENTER
Enter to sub-menu and confirm the menu selection.
SOURCE
Manually select an input source.
MENU/EXIT
Display or exit the on-screen display menus.
Power
Turn the projector on or off.
EN-9
Downloaded From projector-manual.com Viewsonic Manuals
Connection Ports
1
1
2
3
4
5
2
3
4
5
6
7
8
9
10
11
LAN
For network control.
USB
This connector is for firmware update and mouse function support.
VIDEO
Connect composite video output from video equipment to this jack.
S-VIDEO
Connect S-Video output from video equipment to this jack.
MONITOR OUT
Connect to a computer display, etc.
6
AUDIO OUT
Connect to a speaker or other audio input equipment.
7
COMPUTER IN 1
Connect image input signal (analog RGB or component) to this jack.
8
RS-232
When operating the projector via a computer, connect this to the controlling computer's
RS-232C port.
9
COMPUTER IN 2
Connect image input signal (analog RGB or component) to this jack
10
12V OUT
12V DC out
11
AUDIO IN
Connect an audio output from video equipment to this jack. The upper AUDIO IN
is Audio 1, and the lower one is Audio 2. When Audio 1 is turned on, Audio 2 will
turn off automatically and vice versa.
EN-10
Downloaded From projector-manual.com Viewsonic Manuals
Remote Control
1
2
3
4
5
6
POWER
Turn the projector on or off.
VGA1
Select analog RGB signal from
COMPUTER IN 1 terminal.
Source
Manually select an input source by
sequence.
Enter
Confirmed selections.
Keystone+ / Adjust image distortion caused by
tilting the projector.
ViewM
Switch in between high brightness
performance or Accuracy color
performance.
Freeze
Press “Freeze” to pause the screen
image. Press again to cancel the
freeze function.
14
Four directional buttons
Use four directional buttons to select items
or make adjustment to your selection.
Mouse
Switch between OSD control and
Mouse control (Apply to Navigation
buttons, Enter/Mouse Left Click, and
Exit/Mouse Right Click buttons).
15
Exit
Exit OSD Menu.
Laser
Aim the remote at the viewing
screen, press and hold this button to
activate the laser pointer.
16
Magnify
Zoom in and out the images.
10
VGA2
Select analog RGB signal from
COMPUTER IN 2 terminal.
17
Volume + / Adjust the volume level.
11
Video
Select video signal from video
equipment.
18
Mute
Cut off the sound temporarily. Press again
to cancel the Mute function.
12
Auto
Resynchronize the projector to the
input signal from a computer. This
function is available for computer
mode only.
19
Light
Enable backlight functions of the remote
control’s buttons.
13
MENU
Display on-screen display menus.
20
Blank
Cut off the screen temporarily. Press again
to cancel the Blank Screen function.
7
8
9
EN-11
Downloaded From projector-manual.com Viewsonic Manuals
Installing the Batteries
1.
Open the battery cover in the
direction shown.
2.
Install batteries as indicated by the
diagram inside the compartment.
3.
Close the battery cover into
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„ Dispose of used batteries according to the instructions.
„ Make sure the plus and minus terminals are correctly aligned when loading a battery.
„
„
„
„
„
„
Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
Remove batteries from remote control when not using for extended periods.
Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
Danger of explosion may happen if batteries are incorrectly replaced. Replce all
the batteries with new ones.
Batteries should not be in or near to fire or water, keep batteries in a dark, cool
and dry place.
If suspect battery leakage, wipe out the leakage and then replace new batteries.
If the leakage adheres to your body or clothes, rinse well with water immediately.
EN-12
Downloaded From projector-manual.com Viewsonic Manuals
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„ Operating the projector from
the front
15
10
5m
5m
7m
„
Operating the projector from
the rear
10
15
5m
5m
7m
„
„
„
„
„
„
„
Do not point the laser directly to the people's eyes (especially small children).
There is a danger of injury to the eyes.
The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or
humidity.
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
EN-13
Downloaded From projector-manual.com Viewsonic Manuals
Installation
Connecting the Projector
1
USB Cable
5
VGA (D-Sub) to HDTV (RCA) Cable
2
VGA Cable (D-Sub to D-Sub)
6
Composite Video Cable
3
RS-232 Cable
7
S-Video Cable
4
Audio Cable
8
Internet Cable
Laptop type
2
8
4
7
6
2
1
5
Desktop type
3
2
5
4
4
WPG-350
„
„
„
When connecting cable, power cords of both projector and external equipment
should be disconnected from AC outlet.
The figure above is a sample connection. This does not mean that all of these
devices can or must be connected simultaneously.
The cables that come with the projector may differ from the above illustration.
The included cables are based on actual shipment delivery.
EN-14
Downloaded From projector-manual.com Viewsonic Manuals
Powering On/Off the Projector
Powering On the Projector:
1.
2.
3.
4.
Remove the projector lens cap.
Complete the AC power cord and peripheral signal cable(s) connections.
Press
button to turn on the projector.
The projector takes a minute or so to warm up.
Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
„ If you are connecting multiple sources to the projector simultaneously, press
the SOURCE button on the control panel or the Source button on the remote
control.
Warning
„ Remove the lens cap first before powering on.
„ Never look into the lens when the lamp is on. This can damage your eyes.
„ This focal point concentrates high temperature. Do not place any object near
it to avoid possible fire hazard.
Powering Off the Projector:
1.
2.
3.
4.
Press
button to turn off the projector lamp. You will see a message "Power
off? Press Power again" appear on the screen.
Press
button again to confirm.
„ The cooling fans continue to operate for cooling cycle.
„ When the Lamp LED begins flashing, the projector has entered stand-by mode.
„ If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in standby mode, simply press
button to restart the projector.
Disconnect the AC power cord from the electrical outlet and the projector.
Do not turn on the projector right after power off.
EN-15
Downloaded From projector-manual.com Viewsonic Manuals
Adjusting the Projector
Adjusting the Projector Height
Tilt-adjustment foot
Elevator foot
Elevator button
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1.
2.
To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
To level the image on the screen, turn the tilt-adjustment foot to fine-tune the
height.
„
To avoid damaging the projector, make sure that the elevator foot and tiltadjustment foot are fully retracted before placing the projector in its carrying
case.
Adjusting the Projector Zoom and Focus
Zoom ring
Focus ring
1.
2.
Focus the image by rotating the focus ring. A still image is recommended for focusing.
Adjust the image by sliding the zoom ring.
EN-16
Downloaded From projector-manual.com Viewsonic Manuals
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
5.08m / 200"
3.05m / 120"
2.54m / 100"
1.52m / 60"
1.02m / 40"
Wide: 1.4m / 55.1” Tele: 1.7m / 66.9”
Wide: 2.1m / 82.7”
Tele: 2.6m / 102.4”
Wide: 3.6m / 141.7” Tele: 4.4m / 173.2”
Wide: 4.3m / 169.3” Tele: 5.2m / 204.7”
Wide: 7.2m / 283.5 Tele: 8.8m / 346.5”
Screen size
Diagonal
1.02m / 40"
1.27m / 50"
1.52m / 60"
1.78m / 70"
2.03m / 80"
2.29m / 90"
2.54m / 100"
3.05m / 120"
3.81m / 150"
5.08m / 200"
6.35m / 250"
7.62m / 300"
„
„
„
„
Wide
Projection distance
m
1.40
1.80
2.10
2.50
2.80
3.20
3.60
4.30
5.40
7.20
9.00
10.80
4 : 3 Screen
inch
55.1
70.9
82.7
98.4
110.2
126.0
141.7
169.3
212.6
283.5
354.3
425.2
Tele
Projection distance
m
1.70
2.20
2.60
3.00
3.50
3.90
4.40
5.20
6.60
8.80
11.00
13.20
inch
66.9
86.6
102.4
118.1
137.8
153.5
173.2
204.7
259.8
346.5
433.1
519.7
Position the projector in a horizontal position; other positions can cause heat
build-up and damage to the projector.
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may buildup on critical parts and damage the projector or its performance.
Consult with your dealer for special installation such as suspending from a
ceiling.
EN-17
Downloaded From projector-manual.com Viewsonic Manuals
Downloaded From projector-manual.com Viewsonic Manuals
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover.
EN-19
Downloaded From projector-manual.com Viewsonic Manuals
How to operate
1.
2.
3.
4.
5.
6.
Press the MENU button to open the OSD menu.
When OSD is displayed, use S / T to select any feature in the main menu.
After selecting the desired main menu item, press X to enter sub-menu for
feature setting.
Use S / T to select the desired item and adjust the settings with W / X.
Press the MENU button, the screen will return to the main menu.
To exit OSD, Press the MENU button again. The OSD menu will close and the
projector will automatically save the new settings.
Picture (Computer / Video Mode)
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select
each color, you can independently adjust its range and saturation according to your
preference.
Keystone
Manually correct distorted images resulting from an angled projection.
Aspect Ratio
Select how the picture fits on the screen:
„ 4:3 : The input source will be scaled to fit the projection screen.
„ 16:9 : The input source will be scaled to fit the width of the screen.
Image
There are many factory presets optimized for various types of images.
„ PC
: For computer or notebook.
„ Movie
: For home theater.
„ sRGB
: For PC standard color.
„ User
: Memorize user’s settings.
„ White Board : For white projection screen type.
„ Black Board : For black projection screen type.
„ Green Board: For green projection screen type.
„ Daylight Mode: For a daylight environment.
White Intensity
Increase the brightness of white areas.
EN-20
Downloaded From projector-manual.com Viewsonic Manuals
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
3D Sync
„ Off: Disable 3D function
„ 3D-Vision: For NVIDIA 3D Vision application
„ DLP-LINK: For TI 3D DLP-LINK application
3D Sync Invert (for TI 3D DLP-LINK only)
„ On: Invert left and right frame contents.
„ Off: Default frame contents.
Computer Image (Computer Mode)
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Video Image (Video Mode)
Saturation
Adjust a video image from black and white to fully saturated color.
Sharpness
Sharpen or soften the image.
Tint
Shift colors toward red or green.
Sound (Computer / Video Mode)
Volume
Adjust the volume level.
Mute
Cut off the sound temporarily.
Audio 1
Enable or disable Audio 1.
„ When Audio 1 is turned on, Audio 2 will turn off automatically.
Audio 2
Enable or disable Audio 2.
„ When Audio 2 is turned on, Audio 1 will turn off automatically.
EN-21
Downloaded From projector-manual.com Viewsonic Manuals
Setting (Computer / Video Mode)
Menu Position
Choose the menu location on the display screen.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in
front of or behind the screen. Invert or reverse the image accordingly.
Signal Type
Specify the source to the COMPUTER IN 1/COMPUTER IN 2 terminal that you wish to
project.
„ Auto : Automatically detect the input signal type from COMPUTER IN 1 and
COMPUTER IN 2 terminals.
„ RGB : For VGA signal
„ YCbCr/YPbPr:For component signal
Lamp Hours
Display the lamp’s elapsed operating time (in hours).
Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter
cover.
Filter Hours
Display the filter’s elapsed operating time (in hours).
When Filter Mode is turned on, the Filter Hours also turns on automatically.
„
Filter Hours Reset
Reset the filter Hour to 0 hours.
Power Saving
If no operation is performed for a specific period of time, projector will automatically
turn off.
Auto Source
Automatically scan through all the input source.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life.
„ This function will be unavailable when the DCR function is on.
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve
proper high altitude cooling of the projector.
OSD Timeout
EN-22
Downloaded From projector-manual.com Viewsonic Manuals
Duration of OSD menu display countly starts (at idle state by second).
Option (Computer / Video Mode)
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
Password
Set or change the password. When the password function is added, image projection
will require to input the preset password when turning on the projector.
Screen Capture
Capture the current projection screen as a start-up screen.
Start-up Screen
Select start-up screen when the projector is powered on or when no signal is input.
"User" is the screen that you captured.
Zoom
Zoom in and out the images.
Text shot
Using command codes, text messages can be sent for display by the projector over a
network connection. Text is shown on the center of the projection screen. This is a
great way to display urgent alert messages to employees, and simply requires a
connection to the projector’s LAN connector.
DCR (Dynamic Contrast Ratio)
Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable
DCR will resume to normal contrast performance. DCR will impact lamp life and
system noise performance.
Closed Caption
Enable or Disable closed captions by selecting CC1 (closed caption1, the most
common channel), CC2, CC3, CC4, T1, T2 or OFF.
Brilliant Color
Produce an expanded on-screen color spectrum that delivers enhanced color
saturation for bright, true-to-life images. Suggesting to turn Off for most video sources
and On for most computer sources.
™
NetWork
Enable or disable network management via RJ45 connector.
Network Config (Computer / Video Mode)
DHCP
Abbreviation for Dynamic Host Configuration Protocol. This protocol automatically
assigns IP Address to networked devices.
„ When the “DHCP” sets to “Yes”, it takes some time to obtain IP address from
DHCP server.
„ When the "DHCP" sets to "No", that means user will set IP address by manually.
EN-23
Downloaded From projector-manual.com Viewsonic Manuals
Group Name
Display group name.
Projector Name
Display projector's model name.
IP Address
Numerical address to identify networked computers. This function can only be used
when DHCP is set to No.
„ The IP Address is the number that identifies this projector on the network. You
cannot have two devices with the same IP Address on the same network.
„ The IP Address “0.0.0.0” is prohibited.
Subnet Mask
A numeric value to define the number of bits used for a network address of a divided
network (or subnet) in an IP Address. This function can only be used when DHCP is
set to No.
„ The Subnet Mask “0.0.0.0” is prohibited.
Gateway
A server (or router) to communicate across networks (subnets) that are divided by
Subnet Mask. This function can only be used when DHCP is set to No.
MAC Address
Abbreviation for Media Access Control Address. MAC Address is a unique ID number
assigned to each network adapter.
Network Restart
Restart network function when the device is not working properly or to apply changes
made on OSD configuration menu.
Language (Computer / Video Mode)
Select the language used by the on-screen menu.
Factory Default (Computer / Video Mode)
Restore settings to factory default .
System Info (Computer / Video Mode)
Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
EN-24
Downloaded From projector-manual.com Viewsonic Manuals
Network Control
This feature provides the ability to remotely control and manage the projector through
the network.
Preparation:
1.
2.
3.
Connect one end of the internet cable to the Network Control connector on the
projector.
Connect the other end of the internet cable to an available RJ-45 connector on
your computer.
Turn on your projector and computer.
There are two ways to connect to the network control:
A. Auto IP address setting (DHCP : Yes):
1.
Enable DHCP from the projector OSD, under Network Config.
„ When DHCP is enabled, IP Address, Subnet Mask and Gateway
information will get from DHCP server automatically.
EN-25
Downloaded From projector-manual.com Viewsonic Manuals
2.
Start browser in PC and specify following URL, then click “Go” button.
„ URL: http://(Projector IP address)/
„ For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/
3.
If connection succeeds, the login screen is displayed. Enter your User name and
Password and click “OK”. Below are the factory default settings for administrator,
user and passwords.
Item
Administrator
User
User name
Admin
User
Password
<blank>
<blank>
)For setting passwords, please go to Network Control page > Password.
EN-26
Downloaded From projector-manual.com Viewsonic Manuals
B. Manual IP address setting (DHCP: No):
1.
Set IP Address and Subnet Mask under Network Config.
„ IP Address: Numerical address to identify networked computers.
„ Subnet Mask: A numeric value to define the number of bits used for a
network address of a divided network (or subnet) in an IP Address.
„ Gateway: A server (or router) to communicate across networks (subnets)
that are divided by Subnet Mask.
2.
From your computer, go to Start > Settings > Network and Dial-up
Connections > Local Area Connection and right click to select Properties..
EN-27
Downloaded From projector-manual.com Viewsonic Manuals
3.
Select "Intel Protocol (TCP/IP)" and click "Properties".
4.
Set your PC’s IP address, and click OK.
„ Click "Use the following IP address"
„ The network address portion included in the IP address set into your PC
„
should be common with projector’s one.
In this case, projector has “169.254.1.1” IP address, specify “169.254.1.xxx”
for PC’s IP address. Select from 1 to 254 for “xxx” except 2 for PC.
EN-28
Downloaded From projector-manual.com Viewsonic Manuals
5.
Start browser in PC and specify following URL, then click “Go” button.
„ URL: http://(Projector IP address)/
„ For example, if projector IP address is 169.254.1.1, specify URL: http://
169.254.1.1/.
6.
If connection succeeds, the login screen is displayed. Enter your User name and
Password and click “OK”. Below are the factory default settings for administrator,
user and passwords.
Item
Administrator
User
User name
Admin
User
Password
<blank>
<blank>
)For setting passwords, please go to Network Control page > Password.
EN-29
Downloaded From projector-manual.com Viewsonic Manuals
Control the projector via a web browser
Login
If the administrator and user passwords are disabled, it will directly go into the
Status page.
EN-30
Downloaded From projector-manual.com Viewsonic Manuals
If the Administrator & User passwords are enabled, select your User Name and
enter password to login.
Authority on the network control of Administrator & User:
Item
Status
Description
Show current projector status and network
configuration settings.
Control
Control the projector via network.
Network Setting Network configuration & Password setup.
Alert
Show and setup Alert configurations.
Schedule
Show and setup Scheduling configurations.
Administrator
v
User
v
v
v
v
v
v
x
x
v
EN-31
Downloaded From projector-manual.com Viewsonic Manuals
Status
All screen images in this manual are shown when you login with the Administrator ID.
The image will differ if you login with User ID.
Item
IP Address
MAC Address
Projector Name
System Status
Input Status
Lamp Hours
Filter Hours
System Temperature
Projector Status
F/W Version
Date(mm/dd/yy)
Time
Description
Show current IP address.
Show current MAC Address.
Show projector name.
Show if projector is Powered ON or Standby.
Show current input source.
Show lamp used hours on current projector.
Show filter used hours on current projector.
Show system temperature.
Show current projector status, either function normally or error
found.
Show projector's F/W version
Show date set on current projector.
Show time set on current projector *.
Remark:
*If the power has not been supplied for over 50 hours, date and time will be reset.
EN-32
Downloaded From projector-manual.com Viewsonic Manuals
Control
Item
Basic
Power Switch
Input Source
Date
Time
Volume
Mute
Picture
Brightness
Contrast
Color Temperature
Keystone
Picture Mode
Aspect Ratio
Freeze
Video Image
Color
Description
Power On or Power Off the projector via network.
Select input source.
Show date set on current projector.
Show time set on current projector*.
Adjusts the volume setting. (0 - 20)
Enable or disable the mute function.
Adjusts the brightness setting. (0 - 100)
Adjusts the contrast setting. (0 - 100)
Selects the color temperature setting.
Adjusts the keystone setting. (-40 - +40)
Selects the picture mode setting.
Selects the aspect ratio setting.
Enable or disable the freeze function.
Adjusts the color setting.
EN-33
Downloaded From projector-manual.com Viewsonic Manuals
Tint
Sharpness
Computer Image
Frequency
Tracking
H Position
V Position
Setting
Menu Position
Projection
Auto Source
ECO mode
High Altitude
OSD Timeout
Language
Factory Default
Option
ViewMatch
White Intensity
Gamma
Signal Type
Filter Mode
Power Saving
Start Up Screen
Closed Caption
Blank Screen
Adjusts the tint setting. (0 - 100)
Adjusts the sharpness setting. (0 - 31)
Adjusts the frequency. (-50 - +50)
Adjusts the tracking. (0 - 31)
Adjusts the horizontal position. (-10 - +10)
Adjusts the vertical position. (-10 - +10)
Adjusts the menu position.
Selects the projection setting.
Enable or disable the auto source function.
Enable or disable the ECO function.
Enable or disable the high altitude function.
Selects the OSD timeout setting.
Selects preferred OSD language.
Enable or Disable factory default.
Selects ViewMatch setting.
Adjusts white intensity setting.
Adjusts gamma setting.
Selects signal type setting.
Selects filter mode setting.
Selects power saving setting.
Selects start-up screen setting.
Selects closed caption setting.
Selects blank screen setting.
Remark:
*If the power has not been supplied for over 50 hours, date and time will be reset.
„
If the adjustment did not display properly. Please “refresh” or “reload” the
browser again.
EN-34
Downloaded From projector-manual.com Viewsonic Manuals
Network Setting
Item
Network
DHCP
IP Address
Subnet Mask
Gateway
DNS Server
Group Name
Projector Name
Password
Administrator
New Password
Confirm Password
User
New Password
Confirm Password
Description
Assign an IP address to the projector from the DHCP server
automatically or manually.
Setup IP address when DHCP is disable.
Setup subnet mask when DHCP is disable.
Setup gateway when DHCP is disable.
Setup DNS server address when DHCP is disable.
Create projector group. (Max length: 6 characters)
Create projector naming of the current projector. (Max length: 15
characters)
Enable or disable administrative password function.
Setup administrative password. (Max length: 4 characters)
Re-enter administrative password.
Enable or disable user password function.
Setup user password. (Max length: 4 characters)
Re-enter user password.
Click “Submit” button to save the settings.
EN-35
Downloaded From projector-manual.com Viewsonic Manuals
Alert
Item
Email Setting
To
Cc
Subject
From
Server
User Name
Password
Description
Setup the mail alert attendee. (Max length: 40 characters)
Setup the backup mail alert attendee. (Max length: 40 characters)
Setup the subject of the alert e-mail. (Max length: 30 characters)
Setup the sender e-mail address. (Max length: 40 characters)
To enter the SMTP server (Mail server) name of the company.
For example: mail.viewsonic.com (Max length: 30 characters)
Enter user name of the sender’s e-mail account. (Max length: 20
characters)
Enter password of the sender’s e-mail account. (Max length: 14
characters)
Alert Condition
Fan Lock
Over Temperature
Lamp Fail
Lamp Time Alert
The cooling fan is not operating.
The projector internal is over heated.
The lamp does not light up.
Lamp is approaching the end of its useful life in full power
operation.
Replacement is suggested.
Schedule Execution Error Schedule Execution Error.
Filter Time Alert
Filter is approaching the end of its useful life.
Replacement is suggested.
Click “Submit” button to save the settings, then click “Issue Test Mail” to send a test mail
to check whether all settings and functions are correct.
EN-36
Downloaded From projector-manual.com Viewsonic Manuals
Schedule
The schedule function is divided into two scheduling categories, as shown below:
Weekly Schedule: defines the date of each week will execute the command
Click “Add” button to create new schedule. To delete schedule, click “Cancel”. Specific
Day: defines the month and day that will execute the command.
Click “Submit” button to create new schedule. To delete schedule, click “Cancel”.
EN-37
Downloaded From projector-manual.com Viewsonic Manuals
Tips for solving web page problems:
If your web page is not running smoothly, please follow below steps to set the browser.
1.
Go to Tools > General and click "Settings".
EN-38
Downloaded From projector-manual.com Viewsonic Manuals
2.
Click "Every visit to the page" and "OK".
3.
Click "OK" to exit "Internet Properties".
EN-39
Downloaded From projector-manual.com Viewsonic Manuals
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
„
„
„
„
„
Turn off the projector and remove the AC power cord from the power outlet
before beginning maintenance work.
Make sure the lens is cool before cleaning.
Do not use detergents or chemicals other than those noted above. Do not use
benzene or thinners.
Do not use chemical sprays.
Use a soft cloth or lens paper only.
EN-40
Downloaded From projector-manual.com Viewsonic Manuals
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„
„
„
„
„
„
„
„
„
„
The lamp is extremely hot right after turning off the projector. If you touch the
lamp, you may scald your finger. When you replace the lamp, wait for at least
45 minutes for the lamp to cool down.
Do not touch the lamp glass at any time. The lamp may explode due to
improper handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment
of use. There is no guarantee of the same lifetime for each lamp. Some lamps
may fail or terminate their lifetime in a shorter period of time than other similar
lamps.
A lamp may explode as a result of vibration, shock or degradation as a result of
hours of use as its lifetime draws to an end. Risk of explosion may differ
according to the environment or conditions in which the projector and lamp are
being used.
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least
for 5 minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible
material nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable
substance, such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches,
nausea, dizziness, and other symptoms.
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury
inside the lamp will be exposed. Leave the area immediately if the lamp
shatters while being operated and ventilate the area for at least 30 minutes in
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to
user’s health.
EN-41
Downloaded From projector-manual.com Viewsonic Manuals
1.
2.
3.
4.
5.
6.
7.
8.
9.
Turn off the projector.
If the projector is installed in a ceiling mount, remove it
Unplug the power cord.
Loosen the screw in the side of the lamp cover and remove the cover.
Remove the screws from the lamp module, raise the handle, and lift out the
module.
Insert the new lamp module into the projector and tighten the screws.
Replace the lamp cover and tighten the screw.
Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
Reset the lamp hour. Refer to the “Setting” menu.
„
„
„
„
„
„
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may
result in injury or accidents.
Since the lamp is made of glass, do not drop the unit and do not scratch the
glass.
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before
replacing the lamp.
Do not use the projector with the lamp cover removed.
EN-42
Downloaded From projector-manual.com Viewsonic Manuals
Specifications
Display system
Resolution
Zoom
F/No.
Focal length
Screen size
Lamp
Input terminal
Output terminal
Control terminal
Speaker
Video compatibility
Single 1.397cm / 0.55" DLP panel
XGA (1024 × 768)
1.2X
2.5 - 2.73
19.9 - 23.88mm
83.82cm ~ 762cm / 33” – 300”
230W
D-Sub 15-pin x 2, S-VIDEO x 1, VIDEO x 1, Audio signal input
(3.5 mm stereo mini jack) x 2
D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x
1, 12-Vdc trigger output x 1
RS-232 x 1, USB x 1, LAN x 1
5 watt x 2
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
Environment
31 - 80 KHz
50 - 120 Hz
Operating:
Temperature: 0°C to 40°C
Humidity: 30%-85%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
Power requirement
AC 100-240 V, 50 - 60 Hz, 2.5A
Power consumption
290 W
Dimension (W x D x H)
279.5mm x 218mm x 105mm / 11.0" x 8.6" x 4.1"
Weight
2.7 kg (6lb)
Note: Design and Specifications are subject to change without prior notice.
EN-43
Downloaded From projector-manual.com Viewsonic Manuals
Appendix
LED Indicator Messages
LED Type
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Color
Blue
Off
Off
Blue
Off
Off
Blue
Off
Off
Blue
Off
Off
Blue
Red
Red
Blue
Off
Off
Blue
Status
Solid
Off
Off
Solid
Off
Off
Solid
Off
Off
Flash
Off
Off
Solid (Full brightness)
Solid
Flash
Solid (Full brightness)
Off
Off
Solid (Full brightness)
Lamp LED
Temp LED
Off
Off
Solid
Solid
Power LED
Blue
Lamp LED
Temp LED
Red
Red
Flash (Full
brightness)
Solid
Solid
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Blue
Red
Red
Off
Red
Red
Solid (Full brightness)
Flash
Off
Off
Solid
Solid
EN-44
Downloaded From projector-manual.com Viewsonic Manuals
Meaning
The projector is in standby
mode.
Powering up
Normal operation
Power-down
The projector system has some
problems with its fans, so the
projector cannot start up.
The lamp is in good condition
and is projecting at maximum
brightness.
The lamp has reached its end
of life and must be changed
soon. The lamp will continue to
operate until it fails . Change
the lamp. If the lamp is off, then
the ballast will become
malfunction.
The projector is shutting and
the fan motor is cooling the
lamp for shutdown. Do not
unplug the power cord or turn
the power off before the Lamp
LED changes to flashing. The
fan motor will turn off when the
lamp has cooled.
Temperature is too high. The
lamp will turn off. The fan motor
is cooling the lamp.
The lamp ignition failed. If
temperature is too high, the
fans will cool the lamp.
Compatibility Modes
Computer:
Compatibility
VGA
Resolution
640 x 480
640 x 480 @ 120Hz
720 x 400
SVGA
XGA
800 x 600
800 x 600 @ 120Hz
1024 x 768
1024 x 768 @ 120Hz
1152 x 864
1280 x 960
SXGA
1280 x 1024
1280 x 960
1280 x 1024
14460 x 1050
1600 x 1200
H-Sync [KHz]
24.6
31.5
37.9
37.5
43.3
61.9
31.5
37.9
31.0
35.2
37.9
48.1
46.9
53.7
76.3
76.3
48.4
56.5
60.0
68.7
97.6
97.6
67.5
60.0
85.9
64.0
80.0
64.7
75.0
64.0
80.0
64.7
75.0
V-Sync [Hz]
50.0
59.9
72.8
75.0
85.0
119.5
70.0
85.0
50.0
56.0
60.3
72.0
75.0
85.1
120.0
120.0
60.0
70.1
75.0
85.0
120.0
120.0
75.0
60.0
85.0
60.0
75.0
60.0
75.0
60.0
75.0
60.0
60.0
EN-45
Downloaded From projector-manual.com Viewsonic Manuals
Video:
Signal
Horizontal Frequency (kHz)
Vertical Frequency (Hz)
1080i
33.8
60.0
1080i
28.1
50.0
1080p
67.5
60.0
1080p
56.3
50.0
720p
45.0
60.0
720p
37.5
50.0
576p
31.3
50.0
576i
15.8
50.0
480p
31.5
60.0
480i
15.8
60.0
EN-46
Downloaded From projector-manual.com Viewsonic Manuals
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
„ Be sure that the power cord is securely connected to the projector and the other end
is plugged into an outlet with power.
„ Press the power button again.
„ Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
„ Press the SOURCE button on the control panel or the Source button on the remote
control one or more times to select another active input source.
„ Be sure the external source is turned on and connected.
„ For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
„ Be sure the lens cover is removed.
„ While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
„ Check the projection lens to see if it needs cleaning.
If the image is flickering or unstable for a computer connection:
„ Press the Auto button on the remote control.
„ Press the MENU button, go to Computer Image and adjust Frequency or
Tracking.
Remote control problems
If the remote control does not operate:
„ Be sure nothing is blocking the remote control receiver on the front of the
projector. Use the remote control within the effective range.
„ Aim the remote control at the screen or at the front or back of the projector.
„ Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.
EN-47
Downloaded From projector-manual.com Viewsonic Manuals
RS-232 Command and Configuration
Baud Rate:19200 Parity Bit:none
Data Bit:8 Stop Bit:1 Assign Port:COM1
Operation
type
Name
OSD
Header
Command
Response
ON
BE, EF, 10, 05, 00,
C6, FF,
11, 11, 01, 00, 01, 00
06
OFF
BE, EF, 03, 06, 00,
DC, DB,
69, 00, 00, 00, 00, 00
06
Computer
(Analog RGB)
BE, EF, 03, 19, 00,
19, 29,
01, 47, 02, CC, CC, 00
06
YCbCr
BE, EF, 03, 19, 00,
89, E8,
01, 47, 02, CC, CC, 00
06
S-Video
BE, EF, 03, 19, 00,
E8, 69,
01, 47, 02, CC, CC, 00
06
Composite
Video
BE, EF, 03, 19, 00,
78, A8,
01, 47, 02, CC, CC, 00
06
HDTV (Y-PbPr)
BE, EF, 03, 19, 00,
DA, 2B,
01, 47, 02, CC, CC, 00
06
Power
Source
CRC
Menu
BE, EF, 02, 06, 00,
E9, D3,
30, 00, 00, 00, 00, 00
06
Up
BE, EF, 02, 06, 00,
6D, D2,
34, 00, 00, 00, 00, 00
06
Down
BE, EF, 02, 06, 00,
0B, D2,
32, 00, 00, 00, 00, 00
06
Left
BE, EF, 02, 06, 00,
DA, D3,
33, 00, 00, 00, 00, 00
06
Right
BE, EF, 02, 06, 00,
38, D2,
31, 00, 00, 00, 00, 00
06
On
BE, EF, 03, 06, 00,
EF, DB,
6A, 00, 00, 00, 00, 00
06
Off
BE, EF, 03, 06, 00,
3E, DA,
6B, 00, 00, 00, 00, 00
06
On
BE, EF, 03, 06, 00,
89, DB,
6C, 00, 00, 00, 00, 00
06
BE, EF, 03, 06, 00,
58, DA,
6D, 00, 00, 00, 00, 00
06
BE, EF, 02, 06, 00,
57, D0,
2E, 00, 00, 00, 00, 00
06
06
ECO
Auto
Source
Off
Source
Auto-Sync
BE, EF, 02, 06, 00,
86, D1,
2F, 00, 00, 00, 00, 00
Blank Screen(Video)
BE, EF, 02, 06, 00,
DF, DF,
66, 00, 00, 00, 00, 00
06
Keystone
BE, EF, 02, 06, 00,
3D, DE,
64, 00, 00, 00, 00, 00
06
Keystone
Up
BE, EF, 03, 06, 00,
10, DB,
65, 00, 00, 00, 00, 00
06
Down
BE, EF, 03, 06, 00,
23, DB,
66, 00, 00, 00, 00, 00
06
Image
BE, EF, 03, 06, 00,
F2, DA,
67, 00, 00, 00, 00, 00
06
Aspect Ratio
BE, EF, 03, 06, 00,
0D, DA,
68, 00, 00, 00, 00, 00
06
Factory Reset
BE, EF, 03, 06, 00,
6B, DA,
6E, 00, 00, 00, 00, 00
06
Lamp Hour
BE, EF, 03, 06, 00,
BA, DB,
6F, 00, 00, 00, 00, 00
Lamp Hour
Firmware Version
BE, EF, 03, 06, 00,
D5, D9,
70, 00, 00, 00, 00, 00
Version
System Status
BE, EF, 03, 06, 00,
04, D8,
71, 00, 00, 00, 00, 00 03:Projector
ON
(Normal
Mode)
EN-48
Downloaded From projector-manual.com Viewsonic Manuals
D-Sub 9 pin
1
1 CD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
Wire List
C1
1
2
3
4
5
6
7
8
9
SHELL
COLOR
Black
Brown
Red
Orange
Yellow
Green
Blue
Purple
White
DW
C2
1
2
3
4
5
6
7
8
9
SHELL
EN-49
Downloaded From projector-manual.com Viewsonic Manuals
IR Control Code
Format
Byte1
Byte2
Byte3
Byte4
Power
Key
NEC
83
F4
13
87
Source
NEC
83
F4
13
02
Up
NEC
83
F4
13
82
Down
NEC
83
F4
13
85
Left
NEC
83
F4
13
83
Right
NEC
83
F4
13
81
MENU
NEC
83
F4
13
84
Auto
NEC
83
F4
13
64
Mouse
NEC
83
F4
13
6B
ViewMatch
NEC
83
F4
13
63
Freeze
NEC
83
F4
13
80
Enter /
Mouse Left
NEC
83
F4
13
8c
Exit /
Mouse
Right
NEC
83
F4
13
8d
KeyS+
NEC
83
F4
13
86
KeyS-
NEC
83
F4
13
8a
Digital
Zoom+
NEC
83
F4
13
68
Digital
Zoom-
NEC
83
F4
13
6a
Volume+
NEC
83
F4
13
88
Volume-
NEC
83
F4
13
89
Mute
NEC
83
F4
13
8b
Blank
NEC
83
F4
13
8f
EN-50
Downloaded From projector-manual.com Viewsonic Manuals
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region
Web Site
Australia/New Zealand
www.viewsonic.com.au
T=Telephone
F=Fax
AUS=1800 880 818
NZ=0800 008 822
E-mail
service@au.viewsonic.com
T (Toll-Free)= 1-866-463-4775
Canada
www.viewsonic.com
T (Toll)= 1-424-233-2533
service.ca@viewsonic.com
F= 1-909-468-1202
Europe/Middle East/Baltic
countries/North Africa
www.viewsoniceurope.com
Contact your reseller
Hong Kong
www.hk.viewsonic.com
T= 852 3102 2900
service@hk.viewsonic.com
India
www.in.viewsonic.com
T= 1800 11 9999
service@in.viewsonic.com
Korea
www.kr.viewsonic.com
T= 080 265 9080
service@kr.viewsonic.com
Latin America (Argentina)
www.viewsonic.com/la/
T= 0800 666 0194
soporte@viewsonic.com
Latin America (Brazil)
www.viewsonic.com/la/
T= 0800 891 6984
soporte@viewsonic.com
Latin America (Chile)
www.viewsonic.com/la/
T= 800 440 303
soporte@viewsonic.com
Latin America (Columbia)
www.viewsonic.com/la/
T= 01 800 915 6588
soporte@viewsonic.com
Latin America (Mexico)
www.viewsonic.com/la/
T= 001 800 514 6518
soporte@viewsonic.com
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Merida, Yucatan. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru)
www.viewsonic.com/la/
T= 0800 53458
soporte@viewsonic.com
Macau
www.hk.viewsonic.com
T= 853 700 303
service@hk.viewsonic.com
T= 1-800-688-6688 (English)
Puerto Rico & Virgin Islands
www.viewsonic.com
T= 1-866-379-1304 (Spanish)
F= 1-909-468-1202
service.us@viewsonic.com
soporte@viewsonic.com
Singapore/Malaysia/Thailand
www.ap.viewsonic.com
T= 65 6461 6044
service@sg.viewsonic.com
South Africa
www.viewsoniceurope.com
www.viewsoniceurope.com/uk/Support/Calldesk.htm
United Kingdom
www.viewsoniceurope.com/uk/
www.viewsoniceurope.com/uk/Support/Calldesk.htm
United States
www.viewsonic.com
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-1202
Downloaded From projector-manual.com Viewsonic Manuals
service.us@viewsonic.com
Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years
warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp
from the date of the first consumer purchase; Europe except Poland: Three (3) years warranty for all parts
excluding the lamp, three (3) years for labor, and ninety (90) days for the original lamp from the date of
the first consumer purchase; Poland: Two (2) years warranty for all parts excluding the lamp, two (2) years
for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than four (4) hours average daily
usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for
labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe:
One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for
the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a.Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied
with the product.
b. Operation outside of product specifications.
c.Operation of the product for other than the normal intended use or not under normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
Downloaded From projector-manual.com Viewsonic Manuals
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name,
(c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service
center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.
com under Support/Warranty Information.
4.3: Projector Warranty
Downloaded From projector-manual.com Viewsonic Manuals
PRJ_LW01 Rev. 1h 06-25-07
Mexico Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a.Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
unauthorized attempted repair, or failure to follow instructions supplied with the product.
b.Any damage of the product due to shipment.
c.Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3.Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4.Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Product Name: ________________________
Model Number: __________________________
Document Number: ____________________
Serial Number: ___________________________
Purchase Date: ________________________
Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1.To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2.Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1.Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2.Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
Downloaded From projector-manual.com Viewsonic Manuals
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
4.3: ViewSonic Mexico Limited Warranty
Downloaded From projector-manual.com Viewsonic Manuals
PRJ_LW03 Rev. 1A 06-25-07
Downloaded From projector-manual.com Viewsonic Manuals