bmw e65 specification - Video

BMW E65
SPECIFICATION
-. MODEL: QVL-E65-V2
-. Product Code : BM-0807-652
INDEX
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
-.
Updated points on this version
Precaution
Main Spec.
System Composition
Outline Dimension
External Appearance
Connector Pin Assignment
DIP Switch Setting
How to use OSD Keypad
OSD (On Screen Display)
FMTX Frequency Setting
How to use parking guide line
CAN Wiring
Product Composition
FAQ
Updated points on this version
- FMTX Module is added in the product. (No need additional FMTX
Module for Audio)
- Offering OSD Key Pad
(The remote control is not offered anymore)
- Possible to move the displayed position of Navi (Only on RGB mode)
- Changed OSD MENU
Precaution
- You must keep the car key taken off from the car while you work
this and finally, connect power of the interface.
- When to connect the interface cable, you must keep the power
cable taken off.
- You must work this at the environment without any static electricity
or damages.
- All of process on this installation should be done by professionals.
- You must not break the labels attached on the board, if it’s broken,
no warranty.
- When you receive this package you have to check whether there’s
any parts not included and you have to contact us right away.
- Our repair service do not accept any problems caused by user’s
any fault or carelessness.
Main Spec.
1. Input Spec. (MULTI VIDEO INTERFACE)
-. 1 x Analog R,G,B (Sync on Green)
-. 1 x CVBS(REAR CAMERA) Input. (Rear camera source)
- 3 x A/V (NTST & PAL) Input.
-. 1 x LCD Input (Car system Input)
2. Output Spec.
-. 2 X CVBS OUTPUT (Video Out for installing Headrest monitor)
-. 1 x Audio OUTPUT
-. 1 X LCD OUTPUT(LCD Operation)
3. Electric Power Consumption
- Input Power : 8VDC ~ 24VDC
- Consumption Power : 12WATT, Max
4. Switching Mode (AV source)
- Possible to skip AV source while switching Mode (AV source) by DIP S/W
(Refer to the DIP S/W page)
- By ‘SET’ button of the OSD Keypad
- By Toggle Switch (Option)
- By ‘Menu’ button of the car through CAN
※ This function may not support E65 old version which is without “Menu button”
System Composition
Switch for source toggle
OSD keypad
OEM Navi Button (Can Interface)
NAVIGATION Input
(Analog RGB)
MCU
DISPLAY
A/V 1
A/V 2
A/V 3
VIDEO
CIRCUIT
Car installation
OEM LCD
VIDEO MUX
CVBS In
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
POWER
CIRCUIT
A/V OUT
FMTX
(Video out 2
Audio L, R1)
Power Input
(+8VDC ~ +24VDC)
Dip S/W
HEADREST
MONITOR
Outline Dimension
149mm * 91mm * 19mm
149mm
91mm
19mm
※ This can change under manufacturer's circumstance
External Appearance
LCD- IN/OUT
KEY PAD
DIP S/W
LED MODE
RGB (IN)
CAN I/F
A/V(IN/OUT)
※ This can change under manufacturer's circumstance
POWER
External Appearance
DIP S/W
LED MODE
CAN I/F
RGB(IN)
A/V(IN/OUT)
LCD-IN/OUT
※ This can change under manufacturer's circumstance
POWER
KEY PAD
Connector Pin Assignment
*RGB-IN Connect
*Power Connect
⑤
⑥
④
① ② ③ ④ ⑤ ⑥ ⑦
① R DATA (RED)
② G DATA (GREEN)
③
③ B DATA (BLUE)
④ SYNC (WHITE)
⑤ GND (BLACK)
⑥ NAVI IR (WHITE)
⑦ DVD IR (BLACK)
①
②
③
④
⑤
⑥
①
②
GND (BLACK)
I-Drive (ORANGE)
FMT-Antenna (BLUE)
N.C
ACC(RED)
REAR(GREY)
※ This can change under manufacturer's circumstance
Connector Pin Assignment
*CAN Connect
①
② ③ ④ ⑤ ⑥
① CAN HIGH – WHITE
② CAN LOW-YELLOW
③ N.C
④ N.C
⑤ N.C
⑥ N.C
※ This can change under manufacturer's circumstance
Connector Pin Assignment
* Power Cable
FILTER
& FUSE BOX
BLUE
ORANGE
BLACK
Gray
Blue
Orange
990mm
RED
Red
GREY
Black
990mm
FMTX
I - DRV
GND
ACC
LAMP - RV
DIP SW
※ ON : DOWN, OFF : UP
#PIN
FUNCTION
1
RGB INPUT MUTE
2
A/V 1 MUTE
ON : Skipping A/V 1
OFF : A/V1 Display
3
A/V 2 MUTE
ON : Skipping A/V 2
OFF : A/V2 Display
4
A/V 3 MUTE
ON : Skipping A/V 3
OFF : A/V3 Display
5
To select monitor size
6
N.C
7
Rear Mode
8
DIP S/W Selection
ON : Skipping RGB Mode
OFF : RGB Display
ON : 6.5” LCD Setting
OFF : 8.8” LCD Setting
N.C
ON : External Rear Camera
OFF : OEM Rear Camera
N.C
DIP SW
#PIN
모니터 사이즈
NO.5
E65 8.8Inch
OFF
E65 6.5Inch
ON
[E65 8.8 Inch]
※DIP S/W Use Example
[BMW E65-6.5 Inch]
-. Use Input Mode : A/V3(DVD), Navigation (RGB)
-. Rear Camera : When to be installed on CVBS 4
▷ DIP S/W : 1 Æ OFF
▷ DIP S/W : 2,3 Æ ON
(INPUT MODE SKIP)
▷ DIP S/W : 4 Æ OFF (enable A/V3)
▷ DIP S/W : 5 Æ ON (6.5 Inch)
▷ DIP S/W : 6 Æ OFF
▷ DIP S/W : 7 Æ ON (enable CVBS4)
▷ DIP S/W : 8 Æ OFF
[E65 6.5 Inch]
How to use OSD Keypad
MENU : OSD MENU, Going back to the last step of setting after mode
setting
SEL : Select, Mode change
UP : Move to Left, Up
DOWN : Move to Right, Down
*FACTORY MODE : Operated with pressing UP->DOWN->UP->MENU
keys of the keypad sequently.
OSD(On Screen Display)
· Analog RGB Mode
COLOR Menu
- BRIGHTNESS
- CONTRAST
- RED, GREEN, BLUE
- HUE
- COLOR BOX
- SATURATION
- SHARPNESS
· Video Mode
OSD(On Screen Display)
· Analog RGB Mode
· Video Mode
OPTION Menu
OSD H_POS : Move of OSD window to Left, Right
OSD V_POS : : Move of OSD window to Up, Down
OSD TRANS : OSD window transparency setting
SCREEN MODE : Screen Rate setting (4:3, 16:9)
INITIAL : Initializing OSD setting value
OSD(On Screen Display)
· Factory Mode( INTERFACE SETTING)
-Operated with pressing UP->DOWN->UP->MENU keys of the keypad sequently.
Factory Mode (Interface setting)
- POSITION – H-POSITION : Move of Screen to Left, Right (Only for RGB mode)
- V-POSITION : Move of Screen to Up, Right (Only for RGB mode)
- I-DRV – To control DVD, Navi by I-DRV (Optional)
OSD(On Screen Display)
· Factory Mode (INTERFACE SETTING)
Factory Mode (Interface setting)
-FM-TX – FM-TX USE : FMTX Setting
- FREQUENCY : FMTX Frequency Setting (Refer to the next ‘FMTX frequency setting’ page)
-REAR-CAM – By Rear Wire : When to install Back-up Cam by rear wire of power cable (Same with
previous version)
- By CAN-BUS : When to install Back-up Cam by CAN wiring. In this case, when the car
is in reverse, the CAM is detected automatically.
FMTX Frequency Setting
Factory Default : FMTX USE – ON, FREQENCY – 87.5MHz
Get the Factory Mode Operated with pressing
UP->DOWN->UP->MENU keys of the keypad
sequently
Set “FM-TX USE” to “ON” like the left picture.
(‘ON’ is Default). control the frequency by
“UP”, “Down” keys. At the bottom, you can
see present frequency and control it from
87.5MHZ to 108MHZ. (1MHZ per each time to
press)
※If you do not want this function, should set
“FM-TX USE” to “OFF”
How to use parking guide line
Factory Default : DISPLAY - DISABLE
①
① When the car is in reverse, if
press ‘UP’ key for 2 sec, the
guide line appears on the
screen.
②
② If you need to move the line
position, press ‘SEL’ key on
the above step.
(Use ‘Up’, ‘Down’ Key of Keypad)
How to use parking guide line
③
③ On step no.2, once press “SEL”
key again, you can move the
line
vertically by “UP”, “Down” keys.
CAN Wiring
E65 CAN Wiring Diagram
Orange:
CAN HIGH
Green:
CAN LOW
Product Composition
OSD Keypad : 1 EA
LCD In/OUT Cable : 1 EA
Navi Cable : 1 EA
Toggle S/W : 1 EA (Optional)
Power Cable : 1 EA
A/V Cable : 1 EA
Ground Cable (For Keypad) : 1 EA
CAN Cable : 1 EA
FAQ
1. When can not change mode.
-. Check if the Ground Cable (OSD Keypad) is connected or not.
-. Check if LED is turned on or not. If it is not turned on, Check if power cable is connected or not.
-. Check if CAN is connected well.
2. When the screen is displaying only black color.
-. Check if 2nd LED is turned on or not. If it is not turned on, please check all video sources that you
will connect with the interface is operating well or not.
-. Check if interface is connected well.
3. When displayed color of screen is not proper. (If it’s too dark or the color is not proper)
-. Try to push “Reset button” on the remote control. If the color of screen keeps on displaying wrong
color, you have to ask manufacturer for the problem.
-. Try to adjust Color, Contrast, Brightness by the remote.
4. When Back-up camera is not displayed on the screen.
-. Turn Dip S/W no.7 on.
5. When the mode you set is not skip.
-. Check if Dip S/W is set in proper way.
6. When Main screen on the car is not displayed.
-. Check if In/Out cables are connected well. If it keeps showing the same problem, you have to
ask manufacturer for the problem.
7. When the screen is displaying only white color.
-. Check if out cable is connected well. If it keeps showing the same problem, you have to ask
manufacturer for the problem.