SIDACtor Protection Thyristors Teccor brand SIDACtor

SIDACtor Protection Thyristors Teccor brand SIDACtor
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
SDP Series - SOT23-5
Description
This new SIDACtor series is targeted for the tertiary or
line driver side protection position for VDSL2+, ADSL2
applications and general I/O protection functions. This new
low capacitance over voltage protection does not require
a bias voltage and is sufficiently robust for the chip-side
position behind the coupling transformer.
This SOT23-5 solution, with its flow-through design,
minimizes PCB trace layout routing, while its four different
stand-off voltage values offer compatibility with a variety of
line drivers. Its low capacitance makes it compatible with
ADSL2 and VDSL2, and the 30MHz bandplan of VDSL2+.
Features & Benefits
Agency Approvals
Agency
Agency File Number
E133083
Schematic Symbol
• Lower overshooting
protection than clamping
• Bidirectional transient
voltage protection
• SOT23-5 surface mount
package
• Robust surge rating
• Low insertion loss
• Starts to switch in
nanoseconds
• Low capacitance
• RoHS compliant
Applicable Global Standards
(Tip) 1
NC
5 (Tip)
• YD/T 950
• IEC 61000-4-5
• YD/T 993
• ITU K.20/21 Basic Level
• YD/T 1082
• ITU K.20/21 Enhanced
Level
• GR 1089 Inter-building
2
• GR 1089 Intra-building
(Ring) 3
• TIA-968-B
• IEC 61000-4-2
4 (Ring)
• TIA-968-A
Surge Ratings
IPP
Series
8/20µs
Amps min
G
50
Electrical Characteristics
[email protected]=5µA
[email protected]/µs
IH
IS
[email protected]=1.0
Amps
V min
V max
mA typ
mA max
V max
8
15
30
500
4.0
6.5
P12G
12
20
30
500
4.0
6.0
P18G
P24G
18
24
25
35
30
30
500
500
4.0
4.0
5.5
5.0
Part Number
Marking
SDP0080T023G5RP
P08G
SDP0120T023G5RP
SDP0180T023G5RP
SDP0240T023G5RP
[email protected]=1MHz,2V
pF typ
Notes:
- SIDACtor devices are bidirectional. All electrical parameters and surge rating apply to
forward and reverse polarities.
- All measurement are made at an ambient temperature of 25°C.
- Ipp applies to -40°C through +85°C temperature range.
- Ipp is repetitive surge rating and is guaranteed for the life of the product.
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
1
309
Revised: August 9, 2012
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
Maximum Ratings
Parameter Name
Symbol
Test Conditions
Value
Units
Lightning surge waveforms
Ipp
8/20µs
50
A
min
max
Operating Free Temperature Range
TA
-40
+85
°C
Junction temperature
TJ
-40
+150
°C
Storage temperature
TSTG
-40
+150
°C
Notes:
- The device also complies with IEC 61000-4-2 ESD ±15kV (air discharge), ±8 kV(contact discharge) and IEC 61000-4-4 EFT 40A(5/50nS) in equipment level ESD test when used behind the
xDSL transformer.
- The device must initially be in thermal equilibrium with -40°C < TJ < +150°C
- The lightning surge may be repeated after the device returns to its initial conditions.
Mechanical dimensions, recommended layout dimensions
The epoxy meets UL 94V-0 ratings.
Dimension
A
A1
A2
B
C
D
E
F
G
A
0.037(0.95)
D
B
E
A2
A1
C
F
G
0.037(0.95)
Dimension are in inches
(and millimeters).
0.024(0.60)
0.047(1.2)
0.138(3.5)
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
2
310
Revised: August 9, 2012
Inches
Millimeters
Min
Max
Min
Max
0.035
0
0.035
0.014
0.004
0.11
0.059
0.102
0.004
0.057
0.004
0.051
0.020
0.008
0.118
0.069
0.118
0.024
0.90
0
0.90
0.35
0.09
2.80
1.50
2.6
0.10
1.45
0.10
1.30
0.50
0.20
3.00
1.75
3.00
0.60
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
Thermal Considerations
Package
Symbol
Parameter
Value
Unit
TJ
Operating Junction Temperature Range
-40 to +150
°C
TSTG
Storage Temperature Range
-40 to +150
°C
R0JA
Thermal Resistance: Junction to Ambient
120
°C/W
5
4
1
2
3
Holding Current vs. Case Temperature
VS vs. Junction Temperature
Percent of VS Change – %
IH (TC = 25ºC)
1.8
1.6
1.4
25°C
1.2
1.0
Ratio of
IH
2.0
0.8
0.6
0.4
-40
-20
0
20
40
60
80
100 120 140
14
12
10
8
6
25 °C
4
2
0
-4
-6
-8
160
-40 -20
Case Temperature (TC) - ºC
0
20 40 60 80 100 120 140 160
Junction Temperature (TJ) – °C
Capacitance vs. Bias Voltage
V-I Characteristics
+I
9
Capacitance (pF)
8
IT
7
IS
IH
6
5
SDP-08
-V
4
SDP-012
3
IDRM
+V
VT
SDP-018
2
1
0
0
2
4
6
8
10
12
14
16
18
20
22
24
Off-State Voltage (V)
-I
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
VDRM
VS
SDP-024
3
311
Revised: August 9, 2012
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
SDP-xxx Application example
and the SDP3500Q38CB overvoltage protector. GDTs may
also be used on the line side of the coupling transformer. The
flow-through design of the SOT23-5 package is illustrated
below. If the inter winding capacitance of the transformer is
allowing some common mode events to get coupled across,
then the SDP-xxx0T023 can be placed in a three chip mode,
as shown below for additional chip-side protection.
The following schematics show alternate protection solutions
for a typical DSL interface that connects to outside wiring.
This surface mount SOT23-5 chip-side solution provides a
minimum footprint solution appropriate for high density card
designs. The SDP-xxx0T023 will protect the interface from
lightning induced surges on the chip-side of the coupling
transformer. This tertiary protector may be preceded by lineside protection such as the TeleLink over-current protector
DSL driver chipset
Tip
Ring
SDP-018
DSL driver chipset
Tip
Ring
(3)SDP-018
5
1
NC
2
3
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
PCBTrace
4
4
312
Revised: August 9, 2012
PCBTrace
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
Soldering Parameters
- Temperature Min (Ts(min))
Pre Heat
- Temperature Max (Ts(max))
- Time (Min to Max) (ts)
Pb-Free assembly
(see Fig. 1)
+150°C
+200°C
60-180 secs.
Average ramp up rate (Liquidus Temp (TL)
to peak)
3°C/sec. Max.
TS(max) to TL - Ramp-up Rate
3°C/sec. Max.
Reflow
- Temperature (TL) (Liquidus)
+217°C
- Temperature (tL)
60-150 secs.
Figure 1
TP
Peak Temp (TP)
+260(+0/-5)°C
Time within 5°C of actual Peak Temp (tp)
30 secs. Max.
Ramp-down Rate
6°C/sec. Max.
Time 25°C to Peak Temp (TP)
8 min. Max.
Do not exceed
+260°C
TL
TS(max)
Ramp-down
Preheat
TS(min)
tS
25
time to peak temperature
(t 25ºC to peak)
EIA J-STD-002, TEST A.
Part Numbering
Temp Cycling
Mil-STD-883F, Method 1010.8 Condition
C, -65°C to +150°C
168 Hrs, 85°C /60%RH+3IR-Reflow,
260°C +5V, -0°C
Bias Humidity
JESD 22-A101-B 85°C , 85°CRH. 50V
168 Hrs, 85°C /60%RH+3IR-Reflow,
260°C +5V, -0°C
Pressure Cooker
JEDEC 22-A102C No Bias, 121°C,
100%RH 96Hrs/192Hrs.
168 Hrs, 85°C /60%RH+3IR-Reflow,
260°C +5V, -0°C
High Temp Storage
JESD 22-A103C Con B. 150°C, no bias 1000Hrs
HTRB
JESD 22-108C
168 Hrs, 85°C /60%RH+3IR-Reflow,
260°C +5V, -0°C
Thermal Shock
Mil-STD-883F, Method 1011.9 Condition
A, 0°C to 100°C
168 Hrs, 85°C /60%RH+3IR-Reflow,
260°C +5V, -0°C
C-SAM
As per flow, JSTD-020C pre&post
preconditioning test.
Wet Humidity
(Tin only)
NEMI standard: 60°C/93%RH
Part Marking
SDP xxx 0 T023 G 5 RP
Type
Packing Option
SIDACtor DSL Protector
RP: Reel Pack
Nominal Working voltage:
008=8V
012=12V
018=18V
024=24V
5
4
PXXG
Number of pins
Surge Ipp rating
1
2
3
Construction variable:
0=single chip
Pin 1 indicator
Package
T023=SOT23-5
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
Time
Environmental Specifications
100% Matte-Tin Plated
Solderability
Critical Zone
TL to TP
tL
Physical Specifications
Terminal Material
tP
Ramp-up
Temperature
Reflow Condition
5
313
Revised: August 9, 2012
Part Marking Code
SIDACtor ® Protection Thyristors
Teccor® brand SIDACtor® DSL Protection Devices
Packing Options
Package Type
T023
Description
Quantity
Added Suffix
Min. Order Qty.
Industry Standard
SOT23-5
Tape & Reel Pack
3000
RP
3000
EIA-481-A
Tape and Reel Specification — SOT23-5
BDDFTT!IPMF
25/5nn
24nn
291nn
5/1nn
2/6nn
EJB/!IPMF
3/1nn
2/86nn
DM
9nn
5/1nn
71nn
TPU34.6!)9nn!QPDLFU!QJUDI*
9/5nn
VTFS!EJSFDUJPO!PG!GFFE
QJO!2
HFOFSBM!JOGPSNBUJPO
2/!4111!QJFDFT!QFS!SFFM/
3/!PSEFS!JO!NVMUJQMFT!PG!GVMM!SFFMT!POMZ/
DPWFS!UBQF
© 2012 Littelfuse, Inc.
Specifications are subject to change without notice.
Please refer to www.littelfuse.com for current information.
6
314
Revised: August 9, 2012
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Littelfuse:
SDP0080T023G5RP SDP0120T023G5RP SDP0180T023G5RP SDP0240T023G5RP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement