Owner's Manual
and Quick
Installation
Instructions
AUTOMATIC INGROUND POOL CLEANER
THANK YOU FOR PURCHASING THE ALPHA 3™.
YOUR ALPHA 3 HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY
INSTALLED AND TO PROVIDE YEARS OF LOW MAINTENANCE OPERATION.
PRIOR TO INSTALLING YOUR NEW ALPHA 3, PLEASE DO THE FOLLOWING:
1) Complete and return the warranty card.
2) Record your purchase information on the spaces provided below.
3) Attach your invoice (or a copy) to this page.
These actions will insure prompt warranty service, should it be required. Simply present your owner’s manual, along with the invoice at any of our
authorized warranty centers nationwide.
RECORD YOUR ALPHA 3 POOL CLEANER DATA HERE:
Date of Purchase _____________________________________________________________________________________________________________
Purchased From _____________________________________________________________________________________________________________
City __________________________________________________ State/Province _______________________ Zip/Postal Code____________________
Serial No:
A_______________________________________________________
(serial number located on underside of machine head)
ALPHA 3 LIMITED WARRANTY
This Alpha 3 was carefully inspected before shipment from our warehouse. Upon unpacking, if any part proves defective or missing, please notify Zodiac Pool Care,
Inc. immediately. Please consult owner’s manual for complete instructions on the installation and operation of your Alpha 3.
ZODIAC POOL CARE, INC. WARRANTS THE ALPHA 3 POOL CLEANER AGAINST ALL MANUFACTURING DEFECTS AND ALL WEAR AND
TEAR FOR THE FIRST TWO (2) YEARS INCLUDING THE ALPHA 3 HOSE. ALL WARRANTIES ARE EFFECTIVE FROM THE DATE OF
PURCHASE.
Should this product prove defective in workmanship, materials or wear during the applicable warranty period, the consumer’s sole and exclusive remedy shall be such
repair or replacement of the product as provided below.
THIS LIMITED WARRANTY EXCLUDES THE FOLLOWING:
1. Discoloration of the Alpha 3 pool cleaner. This is caused by reaction to ultraviolet rays and the chemicals used in the pool water. Discoloration does not affect the
operating ability of the Alpha 3. Therefore, this Limited Warranty does not cover the replacement of discolored parts.
2. Damage to or malfunction of the unit resulting from excess chlorination or improper water chemistry balance.
3. Replacement of parts which fail or become defective as a result of improper installation, negligence, misuse, abuse or tampering by unauthorized repair personnel.
4. Age, pool water imbalance, and improper installation can cause vinyl pool liners to become brittle or unduly wrinkled. Corrosion of the supporting walls and/or
irregularities in the pool base may also cause liner failure. The use of this product in such an environment is at the pool owner’s risk. Therefore, the pool owner
hereby releases the manufacturer from any and all claims for damage where these conditions exist.
5. The Alpha 3 is designed for use in inground pools only. If unit is used in any other application, the pool owner hereby releases the manufacturer from any and all
claims. This misuse will void all warranty on the unit. The Alpha 3 Pool Cleaner doesn’t work under pool cover.
THE LIMITED WARRANTY PROVIDED HEREIN IS THE SOLE AND EXCLUSIVE WRITTEN WARRANTY WITH RESPECT TO THE ALPHA 3
POOL CLEANER. ALL IMPLIED WARRANTIES IMPOSED BY APPLICABLE LAW, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO EACH COMPONENT OF THE ALPHA 3 ARE LIMITED
TO THE DURATION OF THE EXPRESS LIMITED WARRANTY WITH RESPECT TO SUCH COMPONENT. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
In no event shall Zodiac Pool Care, Inc. be liable in contract or in tort, or under any other legal theory, for lost profits or revenues, loss of use or similar economic loss,
or for indirect, special, incidental, consequential or similar damages, even if it has been advised of the possibility of such claim. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
No claim under this Limited Warranty will be recognized unless the registration card, included in your box, is completed and returned within fifteen (15) days of the
purchase date. Only the original purchaser may submit a claim under this Limited Warranty. Purchaser’s claims against Zodiac Pool Care, Inc. shall be limited to
those claims which may be asserted under the Limited Warranty relating to any defect, malfunction or wear of the Alpha 3.
To obtain warranty replacements or repair, call for authorization at (888) 786-7797. When calling, always supply serial number, evidence of purchase date, retailer
and a brief description of the problems/defects encountered. Zodiac Pool Care, Inc. reserves the right to repair or replace all defective or worn parts covered by this
Limited Warranty and return same to purchaser, freight collect.
Zodiac Pool Care, Inc. assumes no responsibility for any warranties or representations made by other individuals or businesses beyond the express terms contained in
this Limited Warranty.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
2
For sale and use in the United States, Canada and Mexico only. This pool cleaner is not warranted or guaranteed outside of the United States, Canada or Mexico.
This pool cleaner is covered by one or more of the following U.S. and Canadian patents and Canadian registered design:
U.S. patent nos. 4,642,833 – 4,742,593 – 5,315,728 – 5,421,054.
Canadian patent nos. 1,254,105 and 1,256,262.
OTHER PATENTS PENDING.
TABLE OF CONTENTS
General Pool Schematic ...................................................................................... 4
Disc Installation .................................................................................................. 5
Pool Preparation .................................................................................................. 5
Assembly............................................................................................................. 7
Installation........................................................................................................... 8
Pool Pulse™ .........................................................................................................12
Care and Maintenance.........................................................................................13
Balance and Coverage.........................................................................................15
Troubleshooting ..................................................................................................16
Accessories..........................................................................................................17
Parts Diagram ..................................................................................................... 18
Check that the following parts are included:
(1) Universal
Valve Cuff
(1) FlowKeeper™
Valve
(2) 45-degree
installation
adapter elbows
(1) Cleaner
head
(1) Pool Pulse™
(1) Disc
female end
(1) 41/2" Connector
(1) Hose Weight
male end
(12) Standard hose sections
(1) Hose protector
If assistance is required, call 1-888-786-7797
In Canada, please call 1-888-647-4004
IMPORTANT: FOR VINYL LINER POOL OWNERS
Vinyl liners are subject to deterioration or damage due to age, the effect of
chemicals, corrosion or failure of the supporting walls; as well as improper
installation, maintenance or cleaning of the supporting walls or base.
Before installing the Alpha 3™, examine the interior of your pool carefully. If
your vinyl liner is brittle or has stones, wrinkles, roots or metal corrosion in
contact with the underside of the liner, or has damage to the base material or
supporting walls, do not install the Alpha 3 before having a qualified
professional perform the necessary repairs.
3
GENERAL POOL SCHEMATIC
To help you better understand how your new Alpha 3 ™ will work, please read the
following overview:
The pump is the heart of your swimming pool. It pulls water and pushes water, creating a
circulation pattern. The pump is supplied water from the main drain and the skimmer.
Large debris is removed at the skimmer basket and the pump strainer basket. Valves
located in front of the strainer basket control the flow of water coming from the main
drain and skimmer. Pools with a wall vacuum fitting would have a valve located near the
skimmer and main drain valves. The wall vacuum fitting provides an easier access for
cleaning the pool. After water has been pulled by the pump through the suction side of the
system, it is then pushed through your filter, removing fine particles and re-enters the
swimming pool through the return inlets. The return inlets may have directional eyeballs
to aim flow and increase pressure. Water flow through your Alpha 3 makes it move, water
flow in your pool steers the cleaner. Restrictions in the suction line, damaged pump parts,
faulty or improperly set valves, baskets packed with debris and dirty pool filters all affect
flow through the cleaner and will reduce its performance. Improperly aimed return inlets
can create a pattern in the cleaning action of your Alpha 3.
FILTER
PUMP
PUMP
STRAINER
BASKET
SKIMMER & MAIN
DRAIN VALVES
RETURN
INLET
RETURN
INLET
SKIMMER
MAIN
DRAIN
All diagrams are provided for reference and for terminology
used throughout this manual. Your pool may vary.
4
DISC INSTALLATION
Slide the finned disc over the footpad. Be sure it fits properly in the grooves provided.
The fins on the disc face upward.
POOL PREPARATION
For your Baracuda Alpha 3™ to operate properly your pool filtration system must be
operating at maximum water flow. To eliminate readjustment, you must do the
following:
❑ Close the main drain
❑ Manually vacuum the pool
❑ Clean the filter according to the
manufacturer’s instructions and
empty the pump strainer basket
❑ Divert the pool return inlets downward
(see page 6)
5
POOL PREPARATION
For your Baracuda Alpha 3™ to work properly, all return inlets must be pointed
downward and towards each other so that you do not see a circular water flow or
ripples on the surface.
BEFORE ADJUSTMENT
TOP VIEW
SIDE VIEW
AFTER ADJUSTMENT
TOP VIEW
SIDE VIEW
To adjust the return inlet: loosen the lock ring and redirect the eyeball downward, then retighten the lock
ring. If the eyeball is difficult to adjust, insert a screwdriver inside the eyeball and gently adjust downward.
If the return inlets cannot be pointed downward, then you MUST install Baracuda return line diverters.
They are available through your Baracuda dealer (see page 17).
FOR POOLS WITH RETURN INLET
DIRECTIONAL FITTINGS
Replace the directional
eyeball with Baracuda
retrofit eyeball return
line diverter
(Part #90153 for
11/2" return lines;
Part #90155 for
2" return lines),
and reinstall
eyeball retaining
ring (see pg. 17).
6
IF UNABLE TO ADJUST RETURN INLETS
OR FOR POOLS WITHOUT RETURN INLET
DIRECTIONAL FITTINGS
Use Baracuda universal
return line diverter
(Part #24100). Pinch
wires together and
insert fully into
return inlet.
HOSE ASSEMBLY
FOR CORNER OR END INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the corner or end of your pool,
use enough hose sections to reach the farthest point in the pool, plus one (1) section.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM
FITTING
FOR CENTER INSTALLATIONS
If your skimmer or wall vacuum fitting is located at the center of your pool,
use enough hose sections to reach the farthest point in the pool, plus two (2) sections.
SKIMMER / WALL
VACUUM FITTING
SKIMMER / WALL
VACUUM FITTING
Note: You may not use all or you may need more hose sections,
with either installation method, depending upon your pool size.
7
INSTALLATION
The next steps vary based on whether your pool has one skimmer, two skimmers or a
wall vacuum fitting. Please follow the appropriate instructions for your type of pool.
FOR POOLS WITH ONE SKIMMER
❑ Turn the filtration system off.
❑ Using the parts shown below, choose the fitting combination
best suited for your skimmer. You may have parts leftover.
DO NOT INSTALL IN THE SKIMMER AT THIS TIME.
(2) 45° installation
adapter elbows
(1) 41/2" Connector
(1) Hose protector
(1) FlowKeeper™
Valve
(1) Universal
Valve Cuff
FOR POOLS WITH WALL VACUUM FITTINGS
No FlowKeeper™ Valve required
Insert the male end of the hose into the large end
of one 45° elbow. Then insert the small end of
the 45° elbow into the universal valve cuff. The
45° elbow should be angled toward the surface.
8
FOR POOLS WITH TWO SKIMMERS
No FlowKeeper™ Valve required
Insert the male end of the hose
into the universal valve cuff.
INSTALLATION
FOR ALL INSTALLATIONS
Turn on the filtration system. Fill the hose with water by placing the end over a
return inlet.
Submerge the Alpha 3™ pool cleaner head. When bubbles stop coming from the
extension pipe, attach the cleaner head to the female end of the hose.
9
INSTALLATION
FOR POOLS WITH ONE SKIMMER
HOSE PROTECTOR
4 1/2" CONNECTOR
FLOWKEEPER™
VALVE
UNIVERSAL VALVE CUFF
SKIMMER
Remove the skimmer basket, attach the regulator valve combination to the hose and
install into the skimmer. Your installation is now complete.
10
FOR POOLS WITH WALL VACUUM FITTINGS
FOR POOLS WITH TWO SKIMMERS
Insert the cuffed hose end into the wall
vacuum fitting. The 45° elbow should be
angled toward the surface.
Remove the skimmer basket from the
deep end skimmer. Attach the cuffed hose
end to the suction port of the skimmer.
FLOW ADJUSTMENT
FOR POOLS WITH WALL VACUUM FITTINGS AND
FOR POOLS WITH TWO SKIMMERS
Remove the cleaner head. Attach the
Pool Pulse™ to the end of the hose.
You MUST keep the Pool Pulse™
and hose under water.
• For pools with a wall vacuum fitting, leave
the wall vacuum fitting fully open and slowly
close the skimmer valve until the blue
indicator of the Pool Pulse™ falls into the
ideal range (when viewed from the side).
• For pools with two skimmers, leave the
selected skimmer open and slowly close the
other skimmer until the blue indicator of the
Pool Pulse™ falls into the ideal range (when
viewed from the side).
Remove the Pool Pulse ™. Submerge the
cleaner head. When the bubbles stop coming
from the extension pipe, attach the hose end.
Your installation is now complete.
IDEAL
TOO HIGH
TOO LOW
11
POOL PULSE™
The Pool Pulse™ is a flow meter that measures the volume of water flowing through
your Alpha 3™ cleaner. It must be used to properly set the flow on two skimmer or
wall vacuum installations and can be used as a diagnostic tool to check the flow on
any installation.
Always use the Pool Pulse™ with the proper hose length for
your pool. Keep the end of the hose underwater, remove the
cleaner head, submerge the Pool Pulse™ and attach it to the
end of the hose. The blue indicator door should move into
the clear wedge area indicating a flow in the ideal range.
If the flow is too low, review the installation procedures (see
page 11). A dirty pool filter, clogged baskets and improperly
set valves are usually the main cause of low flow. Other
types of hydraulic problems may require a professional pool
repairman.
IDEAL
TOO LOW
If the flow is too high, review the installation procedures.
Confirm that the bypass on the FlowKeeper ™ valve is
opening. Slightly open the main drain if necessary.
TOO HIGH
FLOWKEEPER™
FOR POOLS WITH ONE SKIMMER
The FlowKeeper ™ valve is designed to provide proper constant flow to the
ALPHA 3™ cleaner head. Skimming action is maintained through a bypass throat in
the valve. As the filter collects debris, the valve automatically maintains the correct
flow to the cleaner. The FlowKeeper™ valve comes preset from the factory at a
setting of 6. The last fully exposed number is the setting the valve is at. The lower the
number, the lower the flow to the cleaner head. Should re-adjustment become
necessary, either pull up on the slide plate to raise the setting or lift the top edge of the
slide plate and “walk” the plate down to a lower setting.
12
CARE AND MAINTENANCE
However good an automatic pool cleaner is, remember that it was developed to assist
you with the maintenance of your swimming pool. To maintain quality performance
and increase the lifespan of your Baracuda Alpha 3™, please do the following:
❑ The skimmer basket, pump strainer basket and pool filter should be thoroughly
cleaned on a regular basis to ensure optimum pool cleaner efficiency. Always
disconnect the hose from the skimmer before backwashing.
❑ NEVER COIL THE HOSE when the cleaner is removed from the pool. Hose
memory will influence coverage. A coiled hose can be straightened with hot water
or by laying it in the sun on the pool deck for a few hours.
CORRECT
X
INCORRECT
❑ REMOVE THE BARACUDA ALPHA 3 BEFORE SUPER CHLORINATING.
If you should develop an algae problem or a chemical imbalance problem, remove
the Baracuda Alpha 3 and follow the advice of a qualified pool professional.
Reinstall the cleaner when the imbalance is corrected or after a minimum of 4
hours from super chlorinating.
❑ Periodically inspect the cleaner for signs of wear. The disc and the footpad are the
most critical. When the depth of the channels between the treads of the footpad
are 1/8" or less, replace the footpad.
13
CARE AND MAINTENANCE
EASY ACCESS SYSTEM
Large foreign objects, such as children’s toys, tree branches and rocks, should be removed
manually from your pool prior to operating an automatic pool cleaner. In the event a
blockage occurs, please follow these instructions:
To remove the diaphragm, loosen the outer extension pipe 2 turns (fig. 1). From the
bottom of the cleaner, grip the tab of the diaphragm and pull it out (fig. 2). It will come out
with the inner extension pipe attached and will make a loud noise (fig. 3). Pull the
diaphragm off of the inner extension pipe and inspect it for damage (cuts or tears) or
debris causing a blockage (fig. 4). Pull or rinse out the debris. Do not use tools that might
damage the diaphragm. See your Baracuda dealer for a replacement if necessary.
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
To reassemble, push the inner extension pipe into the diaphragm so that it seats up to
the small lip on the inner extension pipe (fig. 5). Slide the inner extension pipe into
the inner body (fig. 6), then pressing from the ridges, seat the diaphragm into place
(fig. 7). The diaphragm should fit flush against the inlet plate (fig. 8). Tighten the
outer extension pipe until snug. Do not over tighten.
FIGURE 5
FIGURE 7
FIGURE 6
FIGURE 8
14
FIGURE 9
ADJUSTMENTS
BALANCE
Even with the proper flow, a hose weight (part number 43260) may be necessary to
balance the Alpha 3 cleaner head. If the Alpha 3 will not balance correctly in the deep
end of the pool, (as shown below), turn off the pump and add the hose weight
approximately 4 to 7 feet, or 1 1/2 to 2 hose sections away from the cleaner head.
If your pool is 8 feet deep or greater, you may need to purchase a heavier hose weight
(part number 43317) from your Baracuda dealer. Position this weight 9 feet or 2 1/2
hose sections away from the cleaner head. In unusual situations both weights may be
required, with the heavier hose weight (43317) at 9 feet away from the cleaner head
and the lighter weight (43260), 12 feet away from the cleaner head. The primary
reason for the hose weight is to maintain the hose at a 45˚ angle to the pool
cleaner.
Incorrect
Correct
Incorrect
COVERAGE
Normally it is undesirable for the return line water flow to affect the natural
movement of the Alpha 3 hose. However, the following illustration shows how return
line pressure can be used to balance cleaning coverage or to guide the cleaner away
from step areas with “V” shaped corners.
A return line located anywhere along the shaded area can be utilized to gently push
the hose allowing the Alpha 3 to free itself from in-pool obstacles.
TECHNIQUE
Position the return line directional so that you can only detect water movement on the
surface 8 feet out from the wall, and aim it at the center of the opposite wall.
15
TROUBLESHOOTING
PROBLEM
Alpha 3™ patterns or doesn’t
cover majority of pool.
SOLUTION
Use Pool Pulse™ to confirm proper flow (see pg 12).
Divert all return inlets (see pg 6).
Confirm proper hose length (see pg 7).
Check hose for memory (see pg 13).
Add hose weight 4' to 7' from cleaner head (see pg 15).
Use 45º elbow on wall vacuum installations (see pg 10).
Coverage will be limited with the use of a solar blanket.
Note: In cold water 60º or less, water flow must be
increased to compensate for reduced flexibility of hose
and diaphragm (see pg 11).
Alpha 3 sticks at steps.
Utilize flow as shown in coverage section (see pg 15).
Add hose weight 4' to 7' from cleaner head (see pg 15).
Reduce flow to low side of “ideal” range (see pg 12).
Shorten hose if necessary.
Alpha 3 won’t move
or moves slowly.
Use Pool Pulse™ to confirm proper flow (see pg 12).
Backwash filter (sand or DE) or soak cartridge style filter
overnight – consult your pool dealer.
Empty all baskets.
Tighten hose connections.
Check hoses for leaks.
Check diaphragm for damage or blockage (see pg 14).
Note: In cold water 60º or less, water flow must be
increased to compensate for reduced flexibility of
hose and diaphragm.
Alpha 3 won’t move
or moves slowly and air
bubbles are noticeable
at the return jets.
Use Pool Pulse™ to confirm proper flow (see pg 12).
Check hoses for possible leak.
Confirm proper water level in pool.
Replace and lubricate pump lid “O” ring – see your
pool dealer.
Alpha 3 won’t climb walls.
Machine may not climb walls of some vinyl pools or
pools with safety ledges.
Confirm proper hose length (see pg 7).
Use Pool Pulse™ and raise flow to high side of “ideal”
range (see pg 12).
Alpha 3 stays on walls
or edge of pool.
Use Pool Pulse™ to lower flow to low side of “ideal”
range (see pg 12).
Alpha 3 sticks at ladder.
Install ladder guard (see pg 17).
IF ASSISTANCE IS REQUIRED, CALL 1-888-786-7797
16
ACCESSORIES
PART ILLUSTRATION
PART NO.
DESCRIPTION
1. 24000
Ladder Guard
Always use on
stainless steel
in-pool ladders
2. 24100
Return Line Diverter
Use when no other
return inlet directional
fittings exist.
(see page 6).
3A. 90153
(for 2" return inlet)
Retrofit Eyeball Return
Line Diverter
Use to replace standard
directional inlet eyeballs
(see page 6).
4. 26705
The
1
2
(for 11/2" return inlet)
3A
3B
3B. 90155
with 4 1/2"
Hose Connector
Use when heavy debris
or leaf situations exist.
4
5. 43317
Hose Weight
70 gram - Aqua
17
PARTS DIAGRAM
3
1
2
19
4
20
21
5
6
22
23
7
26
8
9
24
1.
2.
3.
4.
5.
16
25
10
12
17
11
13
18
14
15
18
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
PART#
75050
52810
80525
54198
70450
DESCRIPTION
Alpha 3 Outer Extension Pipe w/handnut
Alpha 3 Outer Body Top
Alpha 3 Float
Alpha 3 Outer Body Bottom
Alpha 3 Bumper Fin Complete
QTY.
1
1
1
1
1
48632
48633
70600
48635
74000
71425
61225
48634
72880
46666
73406
81600
81700
60115
44805
22410
33800
53900
33160
43260
38260
20460
Alpha 3 Side Wing A
Alpha 3 Side Wing B
Alpha 3 Outer Body Bracket
Alpha 3 Bottom Bumper
Compression Ring
Alpha 3 Inner Body
Alpha 3 Inner Body plus compression ring
Alpha 3 Belly Weight
Alpha 3 Foot Pad - Teal
Alpha 3 Finned Disc - Teal
Threaded Inner Extension Pipe
Diaphragm Retaining Ring
Diaphragm
FlowKeeper™ Valve
Pool Pulse™
45º Elbow
Hose Protector
Universal Valve Cuff
Alpha 3 41/2" Connector
Alpha 3 Hose Weight
Alpha 3 Hose Section - Aqua -1 Meter
Alpha 3 Hose Kit - Aqua - 12 x 1 Meter
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
LET US HELP! If you are having a coverage problem you cannot solve, mail or fax us the following information
along with a sketch of your pool shape indicating the location of all skimmers, vacuum lines,
inlets, stairs, ladders, swimouts, spas, waterfalls, filter systems or other significant features and a
brief description of the problem.
MAIL TO:
ZODIAC POOL CARE, INC.
2028 NW 25th Avenue, Pompano Beach, FL 33069 or fax to: (954) 977-5065
CUSTOMER NAME: ________________________________________________________ TELEPHONE NO.: ( _______ ) ________________________
ADDRESS: ___________________________________________________________________________________________________________________
CITY: _____________________________________________________ STATE/PROVINCE: _____________ ZIP/POSTAL CODE: ________________
SERIAL NO.: ______________________________________________________________ PURCHASED FROM: _______________________________
POOL SURFACE (circle one):
CONCRETE
VINYL
FIBERGLASS
OTHER: ___________________________________________
POOL SIZE: _______________________________________________________________ PUMP SIZE (H.P.): __________________________________
FILTER (circle one):
SAND
D.E.
CARTRIDGE
FILTER SIZE (or Model No.) __________________________
INDICATE PROBLEM: _______________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
____________________________________________________________________________________________
ZODIAC POOL CARE, INC.
2028 NW 25th Avenue
Pompano Beach, Florida 33069
1-888-786-7797
http://www.baracuda.com
© Copyright 2001
91021