Valor | DTS-660W | User manual | Valor DTS-660W User manual

DTS-660W
Contents
Thank you for your choosing a Valor Multimedia product. We hope you will find the instructions
in this user manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn
how to use all the features of your new unit for maximum enjoyment.
After you have finished reading the instructions, please keep this manual in a safe place for future
reference.
Preparation
Features
Tools and Supplies
Warnings
Disconnecting the Battery
Controls and Indicators
Button Operation
The Key Areas of Touch Screen
Remote Control
Front Zone Remote Control
Rear-Zone Remote Control
Smart Dial Remote Control
TFT Monitor Operation
Open/Close TFT Monitor
TFT Monitor Auto Open
Monitor Tilt Angle Adjustment
Rear Camera Mode
Image Setting
Parking Brake Interlock
Monitor Movement Mechanism
Operating Instructions
Power On / Off
Playing Source Selection
Volume Adjustment
Audio Control Menu
Six-Channel Audio Control
Rear Zone
System Reset
Mute
System Setup Menu
MAIN Menu
Screen Setting
General Setup Menu
ASP(Audio Signal Processing) Configuration Menu
Rear-Zone Operation
Standby
1
1
1
1
2
3
3
4
5
5
6
7
9
9
9
9
9
9
10
10
11
11
11
11
11
12
13
13
13
14
14
15
15
17
19
20
Tuner Operation
Tuner TFT Display
Switch to Radio Tuner source
Select FM/AM Band
Auto Tuning
Manual Tuning
Using Preset Stations
Auto Store (AS)
Program Scan (PS)
Local Radio Stations Seeking (LOC)
DVD Player Operation
Opening/Closing the TFT Video Screen
Insert/Eject Disc
Reset the Loading Mechanism
Accessing DVD Mode
Using the Touch-Screen Controls
Controlling Playback
Accessing the DVD Menu
Moving Through Chapters
Fast Forward/Fast Reverse
Selecting 2-Channel or 6-Channel Audio Playback
GOTO Search
Direct Chapter / Track Selection
Viewing an Alternate Picture Angle (DVD Only)
Zooming
Multi-Language Discs (DVD Only)
Playback Information
General Disc Information
DVD Setup Menu
Accessing the DVD Setup Screen
LANGUAGE Menu
ASP SET Menu
VIDEO Menu
SPEAKER Menu
RATING (Parental Lock) Menu
CD/MP3/WMA/JPEG Operation
CD Player User Interface
MP3/WMA Discs
JPEG Discs
SD Card Reader Operation
Accessing SD Card Mode
Using the Touch-Screen Controls
21
21
21
22
22
22
22
22
23
23
24
24
24
24
24
24
25
25
26
26
26
27
27
28
28
28
28
29
31
31
31
32
32
33
34
35
35
36
37
38
38
38
Preparation
iPod Operation
Accessing iPod Mode
iPod Instructions
Playback of video on iPod
Sat Radio Operation
Accessing SAT Mode
Auto Scan
Manual Scan
Storing a Channel
Recalling a channel
Bluetooth Operation
Before using the Bluetooth
The Bluetooth Indicator
Accessing the Bluetooth Mode
Bluetooth User Interface
Phone Book
Bluetooth Setup
Pairing
Auto Connect
Making a phone call
Answering an incoming call
End a call
Navigation Operation
Access the Navigation mode
Navigation Operation
How to Listen to an Audio program While Using/viewing the Navigation
Troubleshooting
Specifications
NOTE:
1. certain description in the book may differ from the actual unit.
2. Some pictures or icons in the book may differ from actual display.
3. Specifications subject to change without notice.
39
39
39
40
41
41
41
42
42
42
43
43
43
43
43
44
44
45
45
45
45
46
47
47
47
47
48
53
Please read all of the instructions below before beginning your installation. We recommend that
you have your unit installed by an experienced mobile video/navigation installer.
Features
•Double DIN size, all-in-one integrated entertainment system
•Built-in DVD Player, automotive specification slot loading mechanism
•Built-in ISS FM/AM Tuner.
•SD card reader with READ/PLAY functionality.
•Built-in Bluetooth hands-free dial/answer for connection to Bluetooth enabled handsets.
•High resolution 6.5”(16:9) TFT color monitor, contrast and brightness adjustment.
•Built-in 50W X 5 output amplifier, 5.1 channel surround sound output.
•Dual zone function with easy operation.
•Smart Touch-screen operation.
•All functions can be operated by included Remote Controls.
•Rear zone remote control operation.
•”Smart Dial” remote control operation.
•Built-in Satellite Radio Control, Built-in iPod Control, Navigation Ready.
•Powerful Graphic User Interface and software update ability.
Tools and Supplies
We suggest using these tools and supplies to install the unit.
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Multimeter
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
• Heatshrink tubing
• Soldering iron and solder
Warnings
1. Only connect the unit to a 12-volt negative ground system.
2. Never install this unit where operation and viewing could interfere with safe driving
conditions.
3. To reduce the risk of a traffic accident (except when using for rear view video camera) never
use the video display function while driving the vehicle. This may be in violation of local laws.
4. Never disassemble or adjust the unit without the assistance of a professional. For details,
please consult your local car stereo specialty shop.
5. To prevent injury from shock or fire, never expose this unit to moisture or water.
6. Never use irregular discs, the only recommended disc size is a 12cm round disc.
1
Controls and Indicators
7. To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor.
8. Do not change the fuse on the power wire without professional guidance. Using an improper
fuse may cause damage to the unit and result in a fire.
9. The monitor employs an automatic motorized mechanism. To prevent damage to the core
Mechanism, please do not push, pull or swivel the monitor manually.
Disconnecting the Battery
To prevent a short circuit, turn off the ignition and remove the negative (-) battery cable prior to
starting the installation.
NOTE: If the unit is to be installed in a car equipped with an on-board drive or navigation
computer, do not disconnect the battery cable. If the cable is disconnected, the computer
memory may be lost. Under these conditions, use extra caution during installation to avoid
causing a short circuit.
NOTE: It is especially important that you read the WARNINGS and NOTES in this manual
Button Operation
7
1
8
2
3
4
9
10
11
5
12
13
14
6
16
15
17
18
1.MENU
Press to go to MAIN menu.
Press to go to the previous source, if applicable, while in the MAIN menu.
2.FM/AM
Press to change among the following bands: FM1,FM2,FM3,AM
3. AS/PS(AUTO STORE/PROGRAM SCAN)
Press to auto store strong radio stations in the 12 preset channels in the current band.
Press and hold to start to Scan the preset radio station
4.SRC
Press to select a source.
Press and hold to toggle rear zone mode On/Off.
5.POWER OFF/MUTE
Press and hold to power off.
Press Mute or restore the volume.
Press to power on when the machine is in powered off.
6.SMART DIAL/VOL
Press to enter SMART DIAL mode.
Press and hold to enter audio adjust menu, you must wait 15 seconds after your last volume
change. Otherwise, you will set the default start-up volume.
Rotate clockwise/counter-clockwise to control the volume increase or decrease.
Select a new volume level, and then press and hold the knob until hear a long single sound to
store a new default volume.
7.REMOTE CONTROL SIGNAL RECEIVER
2
3
Remote Control
8.SHORT WAY TO SWITCH TO THE NAVIGATION SOURCE
9.PREVIOUS
10.POS
Return to current position
11.NEXT
12.INFO/PIC
Press to display playing information on the screen.
Press and hold to access the picture settings.
13.RESET
Use this button to restart the machine.
14.ANGLE ADJUST
Press to adjust the tilt of the screen.
Press and hold to adjust the tilt of the screen in any angle between 35 to 90,of course you should
loosen the first when you find the best tilt .
15.DISC SLOT
16.DISC INDICATOR LIGHT
It is blue when there is no disc in the unit,
it is red when there is a disc in the unit.
17.EJECT
Press once to eject the disc.
Hold to reset loading mechanism.
18.SD CARD SLOT
Front Zone Remote Control
3
2
4
1
6
5
7
9
8
10
11
13
14
12
16
15
19
20
23
24
27
28
17
18
21
22
25
26
The key areas of touch screen
The touch key areas are outlined below, for DVD, VCD playback mode and so forth.
Power
Open
Turn the power on/off
Mute
Toggle on/off audio output
SRC
Select playing mode
Numeric button
VOL up
VOL down
Information
GOTO search
Stop/Band
Select
A — Return to MAIN MENU
B — Display playing information
C — Select previous chapter
D — Select next chapter
E — Display the on-screen controls, and different mode displays different menu.
F —On DVD/VCD mode, display the GOTO search menu on the screen directly.
4
Open/close the motorized screen
Directly access certain chapter / track / preset
station in current band
Increase the volume
Decrease the volume
Display playing information
Position search function on VCD/DVD mode
Select FM/AM band on Tuner mode
Stop playback
Enter the audio settings
Menu
Exit the current menu
Enter the main menu of system
Picture
Adjust the picture settings
Repeat A—B
OK
Set start point A and end point B to repeat continually
Direction buttons
Up/down/left/right to select items for setting
ESC
Start or pause playback, confirm the settings
5
Select rear playing sources
Title
Also can activate and disable SCAN mode while playing CD
R-SRC
Root
Enter the main menu of the disc
Turn on PBC while playing VCD
Numeric button
Repeat
Repeat playback for current chapter
Mute
Directly access certain chapter / track / preset
station in current band
Toggle on/off audio output
Next
Select the next chapter/track for playback
Search an available radio station by increasing tuning
frequency on tuner mode
GOTO search
Title
Position search function on VCD/DVD mode
Also can activate and disable SCAN mode while playing CD
Select the previous chapter/track for playback
Search an available radio station by decreasing tuning
frequency on tuner mode
Root
Enter the main menu of the disc
Turn on PBC while playing VCD
Previous
OK
Start or pause playback, confirm settings
Fast Reverse
Fast reverse the disc content
Fast Forward
Fast forward the disc content
Audio
Change the audio language for disc playback
Zoom
Angle
Zooming in/out on an image
SUB Title
Language selection for subtitle
Play in different angle for a scene scene(if it is applicable)
Rear-Zone Remote Control
1
2
3
4
Direction buttons
Up/down/left/right to select items for setting
Previous
Select the previous chapter/track for playback
Search an available radio station by decreasing tuning
frequency on tuner mode
Next
Select the next chapter/track for playback
Search an available radio station by increasing tuning
frequency on tuner mode
Stop
Play/pause
Stop playback
Zoom
Zooming in/out on an image
Fast Reverse
Fast reverse the disc content
Fast Forward
Fast forward the disc content
Slower Play
Repeat
Audio
SUB Title
Angle
Repeat A—B
Start/pause playback
Slow forward playback
Repeat playback for current chapter
Change the audio language for disc playback
Language selection for subtitle
Play in different angle for a scene scene(if it is applicable)
Set start point A and end point B to repeat continually
6
5
7
8
Smart Dial Remote Control
10
9
12
13
11
15
16
14
17
18
21
19
20
6
7
TFT Monitor Operation
Open/Close TFT Monitor
3
2
1
Press the (
) button on the front zone remote control or press the (
front panel to open/close the monitor.
) button on the
TFT Monitor Auto Open
•If “TFT Auto Open” is “On”, when the unit is turned on, the monitor automatically opens to the
last viewing position.
•If “TFT Auto Open” is ”Off” , when the unit is turned on, press the (
) button on the remote
control or press the (
) button on the front panel to open the monitor into the desired
viewing position.
w
•If “TFT Auto Open” is ”Manual”, hen the unit is turned on or turned off, the monitor has no
Movement.
See “General setting” for more instructions.
Monitor Tilt Angle Adjustment
VOL down
VOL up
Smart Dial
Decrease the volume
Increase the volume
Press this encoder to access system setup.
Rotate up/down to select a desired item and
press once to access or confirm.
NOTE: The buttons of NAV MENUF1\F2\F3\F4\F5\F6 are used on the navigation mode. If your
unit has the navigation function, please read the user manual of navigation to find the functions
of the buttons.
The monitor angle can be adjusted for optimum viewing using one of the following methods:
• Press the (
) button on the front panel to adjust the tilt angle of the screen one step at a
Time.
• Press and hold the (
) button to continuously adjust the tilt angle.
• Adjust the “Screen Tilt” in the “Screen setting” to adjust the tilt of the screen to the desired
degree.
Rear Camera Mode
When the vehicle is placed in "Reverse", and an optional rear camera is connected to the unit,
the TFT monitor will automatically switch to the camera input source.
Image Setting
Video Output Format
The table below shows the video output format for each source.
SAT
RGB Mode
Adjustable Parameters
While in RGB mode, the only parameter that can be adjusted is brightness (BRIGHT). To access
“SHARPNESS” “COLOR” “CONTRAST” “BRIGHTNESS” and “TINT ”you must be in CVBS
Mode.
8
9
Operation Instructions
Parameter Adjustment Procedure
1. Enter Picture Quality Setting mode:
Press the PIC button on the remote or press and hold the PIC button on the unit.
2. Select Item to Set:
Press the ( / ) buttons on the remote or press the ( / ) buttons on the front panel to
select an item.
3. Set Parameters:
Press the ( / ) buttons on the remote or rotate the SMART DIAL clockwise/counterclockwise
to adjust the selected feature to the desired setting.
4. Exit Picture Quality Setting Mode:
Press the PIC button on the remote or press and hold the PIC button on the unit.
NOTE: There must be a video signal present on the AUX or CAMERA input to adjust the above
settings.
Parking Brake Interlock
1. When the “PARKING” lead is properly connected to the brake switch, the display on the TFT
monitor will display video only when the vehicle is stopped and the parking brake is applied.
2. Parking brake function is overridden when the video source is set to CAMERA.
3. When the “parking brake interlock” is active, the front monitor displays a caution message
with blue background, preventing the driver from watching video while driving to reduce the risk
of a traffic accident. Rear video screens are not affected.
Please see “INSTALLATION SECTION” for installation.
Monitor Movement Mechanism
If an obstruction occurs in the monitor path, the motion will stop automatically to prevent
damage to the mechanism or monitor.
Normal operation is resumed by pressing the (
) button or disconnecting and reconnecting
the power.
Power On / Off
Press the POWER /MUTE button to turn the unit on. You can also turn on the unit by pressing the
button (
) on the remote.
Press and hold the POWER/MUTE button on the front panel or press the POWER button (
)
on the remote to power off the unit.
Playing Source Selection
Press the SRC button on the front panel or the (SRC) button on the remote to change among
available playing sources: TUNER, Disc, iPod, SAT, AUX IN, CAMERA (rear view video camera),
NAVI and SD Card. The playing mode is displayed on the TFT display.
AUX IN Mode
An external audio/video device can be connected to this unit via RCA cables to the “AUX-IN”.
CAMERA Mode
“CAMERA” mode is only available when the camera is connected and when backing up. To
install a rear view video camera, connect the CAMERA video input cable to the rear view camera
output cable.
NOTE: If you have not connected a device to the unit, the source can not be selected. Example:
If you have not connected an iPod to the unit, the iPod source will not be available.
Volume Adjustment
To increase or decrease the volume level, turn the SMART DIAL/VOL on the front panel or press
the VOL+/ VOL- buttons on the remote control. The volume ranges from “0” to “40”. The default
volume is “10” when the unit is powered on each time. Default volume memory setup: Rotate
Smart Dial/VOL knob on the front panel to select volume value and then press and hold the
Smart Dial/VOL button until you hear a single beep. When you hear the beep, setup is
completed.
Audio Control Menu
The Audio Control feature allows you to easily adjust your audio system to meet the acoustical
characteristics of your vehicle, which vary depending on the type of vehicle and its
measurements. To get the best possible sound quality from your new system, be sure to adjust
the settings for the speakers as well. Proper setting of the Fader and Balance boosts the effects
of the cabin equalizer.
Accessing the Audio Control Menu
Press and hold the SMART DIAL/VOL button on the front panel for more than 2 seconds (you
must wait 15 seconds after your last volume adjustment before attempting to enter the audio
control menu via the SMART DIAL) or press the (SEL ) button on the remote control to display
The “Audio” menu.
Selecting an Audio Feature for Adjustment
Press the ( / ) buttons on the remote or press the SMART DIAL/VOL button on the front
panel once to select a audio feature to be adjusted.
Adjusting an Audio Feature
Press the ( / ) buttons on the remote or rotate the SMART DIAL/VOL
Clockwise/counterclockwise to adjust the selected feature to the desired setting.
10
11
Audio Adjustments
Rear Zone
If a monitor is installed in the rear zone and connected to the rear zone AV output, passengers in
the back seat can control the DVD output using the rear zone remote control. See “Rear-Zone
Remote Control” for instructions.
System Reset
To correct a system halt or other unusual operation, use the tip of a pen to press the RESET
button located on the front bottom-right corner of the unit. After a system reset, the unit restores
the settings before last power off.
Mute
The volume will be muted when the following cases occur:
• Automatic: audio output mutes when a telephone call is received by the car phone or when
verbal navigation is performed.
• When the “MUTE” wire is connected to a cell phone that will output a mute signal to the “MUTE”
Wire.
• Manual: Press the MUTE button (
) on the front panel or the MUTE button (
) on the
remote to mute the volume from the unit.
NOTE: Press the MUTE button again to restore the volume.
Adjusting the volume or using any of the audio set-up features will cancel the mute function.
NOTE: The Bass and Treble levels are only adjustable when EQ is on “User” mode.
The Loudness function compensates for deficiencies in sound ranges at low levels. Loudness
levels range from 1-4 or “off”. When the Loudness function is on, LOUD is displayed on the
screen.
Exiting the Audio Control Menu
Press and hold the SMART DIAL/VOL button on the front panel to exit the audio control menu, or
touch the return arrow on the top right of the display.
Press the (ESC) or (SEL) button on the remote control to exit the audio control menu.
Six-Channel Audio Control
6-Channel Audio Adjustments
Item
Master Volume
Front Left Channel Volume
Front Right Channel Volume
Rear Left Channel Volume
Rear Right Channel Volume
Center Channel Volume
Subwoofer Volume
12
00 to 40
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
13
System Setup Menu
MAIN Menu
Screen Setting
Accessing the Screen Setup Menu

•Press the MENU on the front panel or press the (MENU) button on the remote control to access
MAIN menu.
•Select the
button on the right bottom of the screen to access the Screen setup.
There are three methods to access the MAIN menu.
•Press the MENU button on the front panel .
•Press the MENU button on the remote control.
•Touch the A area on the touch-screen.
10
11
8
13
9
17
12
15
14
16
18
1
2
3
4
5
6
7
1.Touch to access Front-Zone menu.
2.Touch to access Rear-Zone menu.
3.Touch to access DVD setup.
4.Touch to access ASP setup.
5.Touch to access General setup.
6.Touch to access Screen setup.
7.Touch to turn to the previous menu.
8.Bluetooth indicator.
9.Touch to access Tuner mode.
10.Touch to access DVD mode.
11.Touch to access iPod mode.
12.Touch to access SAT Radio mode.
13.Touch to access AUX IN mode.
14.Touch to access SD Card mode.
15.Touch to access Navigation mode.
16.Touch to access Camera mode.
17.Touch to access Bluetooth mode.
18.Touch to access the Standby mode.
Note: Remote, Smart dial, touch screen operations and buttons on front panel are all useable to
select menu and adjust settings. The following instructions will show the different ways to
access menus and adjustments.
14
Selecting a Feature for Adjustment
Press the ( / ) buttons on the remote to select a feature to be adjusted.
Rotate SMART DIAL clockwise/anticlockwise to select a feature to be adjusted. Touch directly
the options on the screen to select a feature to be adjusted.
Adjusting a Feature
General setup Menu
Accessing the General Setup Menu
•Select the TOOLS button on the bottom of the touch screen to access the General setup.
15
Selecting a Feature for Adjustment
Press the direction buttons on the remote control or touch the option directly on the screen to
select the feature to be adjusted.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust by pressing the (OK) button on the
remote or by pressing the SMART DIAL button. A submenu appears in a second row with the
selected option.
2. Select a new value by pressing the direction button.
3. Confirm your selection by pressing (OK) button or pressing the SMART DIAL button. The new
value setup is complete.
Adjusting the Clock
1. Access the “Clock” setting under the General Setup menu.
2. Press the direction button on the remote to move the cursor to the “Hour” or “Min” position,
and press the (OK) button. you also can touch the “Hour” or “Min” position directly.
3. The numeric keypad will pop up.
4. Press the numeric button on the remote control or touch the numeric keypad on the screen to
adjust the hour or minutes.
5. Press the (OK) button on the remote control or on the keypad of the screen to confirm setup.
Return to normal playback
The system will automatically return the previous playback mode that it was in before accessing
the setup menu 20 seconds after the last operation.
16
Bluetooth
Select to activate/deactivate the Bluetooth function.
ASP(Audio Signal Processing) Configuration Menu
The ASP Configuration menu allows you to make fine audio adjustment.
Accessing the ASP Configuration Menu
•Press the MENU on the front panel or press the (MENU) button on the remote control to access
MAIN menu.
•Select the SPEAKER TOOLS button on the bottom of the screen to access the ASP setup.
•A menu appears with the option for the first item, and then you can touch the
button to the
option on the next page, press the
button to return.
17
10KHz
Treble Freq
12.5KHz
15KHz
Depending on the audio source, select the Treble
Center Frequency to achieve the best Treble effect.
17KHz
160Hz
Selecting a crossover frequency sets a cut-off
frequency of the subwoofer’s LPF(low-pass filter)
and the “SMALL” speakers’ HPF (high-pass filter).
The Crossover frequency setting has no effect if
the subwoofer is set to “Off” and any other speaker
is set to “Large”.
0°
Subwoofer output IN phase
180°
Subwoofer output OUT OF phase
80Hz
Sub Filter
Sub Phase
120Hz
NOTE: Depending on your installation, reversing the
subwoofer phase may increase bass output.
1.0
Bass Q-Factor
1.25
1.5
When the Bass Center Frequency is selected,
adjusting the Bass Q-Factor alters the sharpness
of the Bass output.
2.0
Selecting a Feature for Adjustment
Press the direction buttons on the remote control or touch the option directly on the screen to
select a feature to be adjusted.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust by pressing the (OK) button on the
remote or by pressing the SMART DIAL. A submenu appears in a second row with the selected
option.
2. Select a new value by pressing the direction button.
3. Confirm your selection by pressing (OK) button on the remote control or pressing the SMART
DIAL on the front panel. The new setup is complete.
Return to normal playback
The system will automatically return the previous playback mode that it was in before accessing
the setup menu 20 seconds after the last operation.
FM/AM Gain
-07 ~ +07
Adjust the FM/AM gain
DVD Gain
-07 ~ +07
Adjust the DVD gain
NAVI Gain
-07 ~ +07
Adjust the NAVI gain
Bluetooth Gain
-07 ~ +07
Adjust the Bluetooth gain
SAT Gain
-07 ~ +07
Adjust the SAT gain
iPod Gain
-07 ~ +07
Adjust the iPod gain
AUX IN Gain
-07 ~ +07
Adjust the AUX IN gain
SD Card Gain
-07 ~ +07
Adjust the SD Card gain
Rear-Zone Operation
Independent sources can be played simultaneously on the unit. For example, the FM/AM tuner
can be listened to by the front passengers, while DVD video is available to rear passengers.
Access Rear-Zone
1.Touch the REAR ZONE button on the bottom of the display to access the Rear-Zone menu and
you can select a source to play.
60Hz
80Hz
Bass Freq
100Hz
130Hz
Depending on the audio source, select the Bass
Center Frequency to achieve the best Bass effect.
150Hz
200Hz
18
19
Tuner Operation
2. Use the Multi-Zone Remote Control to access the Rear-Zone and select a source to play.
3. Press and hold the SRC button on the front panel to toggle Rear-Zone mode On.
Exit Rear-Zone
1.Touch the Off button on the Rear-Zone menu.
2.Press and hold the SRC button on the front panel.
NOTE: If DVD is selected as the front source and SD Card can not be selected for the rear
source, if SD card is selected as the front source and DVD can not be selected for the rear
source .Since the multimedia processor is shared between optical and SD Card media, one or
the other can be selected but not both simultaneously.
Selecting a Source for the Front Zone
Access the Front-Zone menu, and this menu allows you to select a source for the front zone.
You can also use the button on the front panel or on the front remote control.
The AM/FM tuner/iPod/SAT Radio graphics will change to a "blue screen" background when the
DVD player or SD Card media is selected from the Rear-Zone menu.
Remote, Smart dial, touch screen operations and buttons on front panel are all useable to
control the front source.
The functions of the buttons on the touch-screen are discribed in the next chapters about AM/FM
tuner/iPod/SAT Radio.
NOTE: Optical media and an SD Card cannot be selected from the Rear-Zone Source Menu
simultaneously.
Standby
1. Touch the
button on the touch-screen to access Standby mode.
2. In the standby mode, the unit stands in low-power state with audio output only.
3. In the standby mode, you can return to normal screen mode by performing any unit operation.
Tuner TFT Display
6
1
13 3 12
2
4
5
11
7
8
9
10
14
15
16
17
18
19
20
1.Current Source information, touch this area to return to MAIN menu
2. Current Radio Band Indicator
3. Current Preset Station playing Indicator
4. Stereo Broadcast Indicator
5. Radio Frequency Indicator
6. Preset Radio Stations: Touch to recall preset stations or touch and hold to store a station.
(total 12 stations a Band can be preset.)
7. System EQ setting
8. Loud Setting Indicator (See “Audio control menu” for instructions. )
9. Rear Zone Playing Mode
10.Volume Indicator.
11.Strong Local Signal Broadcasting Indicator: Touch to active Local/DX function
12.Current time
13.Bluetooth Indicator
14.
: Touch to change among the following bands: FM-1, FM-2, FM-3 and AM.
15.
: Touch to automatically scan and store stations in current radio band. You also can
press the AS/PS button on the front panel.
16.
: Touch to seek down.
17.
: Touch to seek up.
18.
: Touch to tune down once a step.
19.
: Touch to tune up once a step.
20.
: Touch to activate/deactivate Scan Mode
Switch to Radio Tuner source
Press the SRC button on the front panel or on the remote control to switch to the Tuner source.
You can also access the tuner mode from the MAIN menu directly.
20
21
Select FM/AM Band
Program Scan (PS)
Touch the
button on the screen, or press the BAND button(
change among the following bands: FM-1, FM-2, FM-3 and AM.
)on the remote control to
Auto Tuning
Press the button (
) on remote control or touch the
button on the screen to seek the
next available channel by increasing the tuning frequency. Press the button again to stop
searching.
Press the button (
) on the remote control or touch the
button on the screen to seek
the next available channel by decreasing the tuning frequency. Press the button again to stop
searching.
1. Press and hold the AS/PS button on the panel Or press the
button on the screen.scan
the stations in the 12 preset channels in the current band.
2. Touch the
button on the screen to automatically scan all stations in current band to
preview stations.
3. Press any button to stop scanning and listen to the selected station.
Local Radio Stations Seeking (LOC)
When the Local function is on, only radio stations with a strong signal are tuned. When the Local
function is active, “LOC” appears on the screen and an indicator is illuminated.
To activate the Local function in AM/FM tuner mode, touch the
button on the screen .
Touch the
again to Activate the DX function
Manual Tuning
Press the
button on the remote control or touch the
frequency one step at a time.
Press the
button on the remote control or touch the
frequency one step at a time.
button to increase the tuning
button to decrease the tuning
Using Preset Stations
12 numbered preset buttons store and recall stations for each band. Front 6 stored stations (P1P6) for the current band appear on the screen, touch the channel directly for use.
You can touch the arrow buttons
on the screen to see the other 6 stations.
Storing a Station
1. Select a band (if needed), then select a station.
2. Touch and hold an onscreen preset button (6) for three seconds. The preset number appears
at the top of the screen.
Recalling a Station
1. Select a band (if needed).
2. Touch an on-screen preset button (6) to select the corresponding stored station.
Auto Store (AS)
Press the AS/PS button on the panel or Press and hold the
automatically scan and store all stations in current band.
22
button on the screen to
23
DVD Player Operation
NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless
the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT
screen displays caution information with a blue background. Rear video screens, if applicable,
will operate normally.
Opening/Closing the TFT Video Screen
Opening the TFT Screen
To open the TFT video screen, press the (
) button on the unit or press the (
) button
on the remote control.
Closing the TFT Screen
Press the (
) button on the unit or press the (
) button on the remote control again to
Close the TFT screen.
1.Touch to Play/Pause
2.Touch to stop
3.Touch to fast reverse
4.Touch to fast forward
5.Touch to repeat playback
6.Touch to repeat from A to B. Select the repeat point A wherever you want to start and the point
B wherever you want to end, then, DVD displays from A to B continually.
7.Touch to choose a language, if the disc is recorded in multiple languages.
8.Touch to display Sub-title
9.Touch to return to DVD main menu
Controlling Playback
Insert/Eject Disc
Inserting a Disc
When inserting a DVD disc, DVD mode is entered and disc play begins.
NOTE: If Parental Lock (Rating) is activated and the disc inserted is not authorized, the 4-digit
code must be entered and/or the disc must be authorized (see “RATING (Parental Lock) Menu”).
You cannot insert a disc if there is already a disc in the unit or if the power is off.
NOTE: CD-R/RW, DVD-R/RW, DVD+R/RWs will not play unless the recording session is closed.
Ejecting a Disc
Press the button
on the unit to eject the disc. The unit automatically reverts to Tuner mode
at the same time.
Reset the Loading Mechanism
If the disc loads abnormally or does not play properly, press and hold the button
to reset the loading mechanism. The disc is ejected and normal operation resumes.
on the unit
Accessing DVD Mode
To switch to DVD mode when a disc is already inserted, press the SRC button on the front panel
or on the remote control till DVD appears at the top of the screen.
Using the Touch-Screen Controls
Stopping Playback
Touch the stop button
on the screen or press the (
) button on the remote control to
stop DVD play; touch the play/pause button
on the screen or the (OK) button on the remote
Control to resume disc play.
Pausing Playback
Touch the play/pause button
on the screen to suspend or resume disc play.
Repeat Playback
Press the Repeat button
on the screen or on the remote control to alter repeat mode
according to the following:
• DVD: Repeat Title, Repeat Chapter, Repeat Off
• VCD (PBC Off): Repeat Single, Repeat Off
• MP3: Repeat Single, Repeat Folder, Repeat Off
NOTE: For VCD play, the repeat function is not available if PBC is on.
PBC (Play back Control) (VCD Only)
For VCD with play back functionality, play back control (PBC) provides additional controls for
VCD playback.
Press the (ROOT) button on the remote control to toggle the PBC function “On”/”Off”. Once PBC
is on, playback starts from track one of the play list.
NOTE: When PBC is activated, fast forward, slow playback, and previous/next track are
available. Repeat and direct track selection are not available. When PBC is activated, selecting
random, scan, or search playback automatically deactivates PBC.
Sectional Repeat Function (A-B)
Use the A-B function to define a specific area of a disc to repeat.
• Press the Repeat A-B button (
) on the screen or on the remote control to set the start
point (A) of the repeated section.
• Press the Repeat A-B button (
) again once you reach the desired end point (B) of the
repeated section. The selected portion of the DVD will now repeat continuously.
• Press the Repeat A-B button (
) again to cancel the A-B section setting and stop repeat
play.
Accessing the DVD Menu
1.You can touch the area F, and then touch the
24
25
button to recall the main DVD menu.
2.Use the arrow buttons on the remote to select a title from the menu.
3.Press the (TITLE) button on the remote control to select a different title for playback.
4. Press the (OK) button on the remote control or touch the item directly to confirm your
selection and begin playback.
Moving Through Chapters
Press the (
) button on the remote control to advance to the next chapter on the DVD.
Press the (
) button on the remote control to move to the previous chapter on the DVD.
Touch the right side of the screen to advance to the next chapter, or touch the left side of the
Screen to move to the previous chapter.
GOTO Search
During DVD or VCD playback, perform the following steps to use the GOTO feature to access a
specific location on a disc:
1. Press the( -/--) button on remote control or touch Area F on the screen to enter “GOTO” mode.
2. Press the (
/ ) buttons on the remote control to select a category.
• For DVD mode, you can choose Time or Title/ Chapter search.
• For VCD mode, press the( -/-- ) button to choose between Track Search, Disc Search and Exit.
Fast Forward/Fast Reverse
Press the (
) button on the remote control or touch the
of area E on the screen to fast
forward. Keep pressing or touching and releasing the button to increase the rate from “2X” to
“4X”, “8X”, and “20X”.
Press the (
) button on the remote control or touch the
of area E on the screen to fast
reverse. Keep pressing or touching and releasing the button to increase the rate from “2X” to
“4X”, “8X”, and “20X”.
Selecting 2-Channel and 6-Channel Audio Playback
2-Channel Audio (Down Mix) Support for CD, SD Card and DVD
Linear pulse code modulation (LPCM) and pulse code modulation (PCM) support is available for
CD, SD Card and DVD discs when 2-channel audio is selected.
6- Channel Audio Support for CD, SD Card and DVD
Surround I is available for decoding analog or digital 2- channel down mixed sources. Surround
II is available for decoding digital bit-stream sources.
NOTE: Only 2-Channel audio support is available for AM / FM tuner, Auxiliary input.
3. Touch the(
Screen.
)/ (--- /---) area on the screen to display a numeric keypad on the touch
Speaker Output Options
Speaker Setup
Front speaker Rear Speaker Center Speaker
Sub- Woofer
2CH mode
Play 2CH audio in
6CH mode with
surround “off”
4. Enter a time/Track number into the field using the numeric keypad on the remote control or on
the screen.
5. Press the OK button on the remote control or on the touch screen to go to the specified
Location on the disc.
6. Press the ( -/-- )button on the remote control or touch the F Area on the screen again to exit.
Play 2-channel
(DownMix) audio
in 6-channel mode
with surround “on”
Play 6-channel
audio in 6-channel
mode
Direct Chapter / Track Selection
During DVD, VCD and CD playback, you can use the numeric keypad on the remote control to
access a track directly.
26
27
Viewing an Alternate Picture Angle (DVD Only)
Some DVDs contain scenes that have been shot simultaneously from different angles. For discs
recorded with multiple angles, press the (ANGLE) button on the remote control to toggle
available angles of the on-screen image.
VCD Playback Information
The following information is displayed at the top of the screen during VCD playback:
Zooming
Press the ZOOM button on the remote control to enlarge and pan through the video image using
the following options: “Q1”, “Q2”, “Q3”, and “Off”.
Multi-Language Discs (DVD Only)
Changing Audio Language
If you are watching a disc recorded in multiple languages, press the (AUDIO) button on the
remote control to choose a language. You also can touch area E, and then touch the
button.
NOTE: During VCD playback, press the (AUDIO) button on the remote control to choose
between Left Channel, Right Channel, and Stereo.
Changing Subtitle Language
If you are watching a disc recorded in multiple languages with subtitles, press the (SUBT) button
on the remote control to choose the language in which you would like the subtitles to appear. You
also can touch area E, and then touch the
button.
1.Indicates Current playing source.
2.Indicates the forth of 16 tracks on the DVD is currently playing.
3.Indicates the playback time of the current title.
4.Indicates EQ Setting.
5.Indicates the Loud Setting.
6.Indicates the current system time.
7.Indicates the current playback source of the rear zone.
General Disc Information
Playback Information
During DVD and VCD playback, press the (INFO) button on the remote control or touch area B to
display playback information on the screen, including the media playing and current playback
time.
DVD Playback Information
The following information is displayed at the top of the screen during DVD playback:
Disc Symbols
1.Indicates Current playing source.
2.Indicates the forth of 16 titles on the DVD is currently playing.
3.Indicates the first of 20 chapters on the DVD is currently playing.
4.Indicates the playback time of the current title.
5.Indicates EQ setting (or decoding mode when listening to a DVD with 5.1 surround
6.Indicates the Loud Setting.
7.Indicates the current system time.
8.Indicates the current playback source of the rear zone.
28
sound.)
29
DVD Setup Menu
In “DVD Setup” mode, “LANGUAGE”, “ASP SET”, “VIDEO”, “SPEAKER” “SURROUND” and
“RATING” (parental lock) are available for setup. This operation can be performed using rotary
encoder, the remote control or touch screen.
Accessing the DVD Setup Screen
If DVD is selected as the current playing source, you can access the DVD setup screen through
the following methods:
• Press the MENU on the front panel or touch area A to access the MAIN menu, and then touch
the DVD TOOLS button to access DVD Setup Screen.
• Press the (MENU) button on the remote control , press the direction button to select DVD
TOOLS and press the (OK)button to access.
Accessing a Menu
To access a menu (LANGUAGE .ASP SET, VIDEO, SPEAKER. SURROUND, RATING), press
the direction buttons on the remote control to highlight the desired menu. You can also touch the
on-screen menu selection to access that menu.
NOTE: Once the DVD setup is complete, the settings are memorized. If you want To restore the
factory default settings, please use the “Load Factory “ in the RATING Menu. (See RATING
Menu.)
Selecting a Feature for Adjustment
Once inside a menu, press the ( / ) on the remote control or touch the item directly to select
the feature to be adjusted.
Adjusting a Feature
1. Enter the option field for the feature you want to adjust by pressing the (OK) button on the
remote or by pressing SMART DIAL. A submenu appears in a second row with the selected
option.
2. Select a new value by pressing the ( / ) buttons on the remote control or rotate clockwise
or counter-clockwise the SMART DIAL.
3. Confirm your selection by pressing the (OK) buttons on the remote control, or press the
SMART DAIL. The new setup is completed.
LANGUAGE Menu
If a DVD supports more than 1 Subtitle or Audio language, all the languages are available for
selection during playback. If the selected language is not supported by the DVD, then the default
language is used. During playback, press the (SUBT)or (AUDIO) button on the remote control to
Change the language directly. This will not affect the DVD menu settings.
LANGUAGE Menu Features
30
31
TV Shape
(Aspect Ratio)
4:3
Image is presented in wide view with a 4:3 aspect
ratio.
16:9
Image is presented in wide view with a 16:9 aspect
ratio.
ASP SET Menu
The unit has a built-in Pink Noise generator to help set the relative speaker levels for multichannel audio playback.
ASP SET Features
Off
Pink noise
DRC
Stop output of pink noise
Left
Left channel pink noise
Right
Off
Right channel pink noise
Employ the Dynamic Range Control for better
playback for low volumes.
On
NOTE: For standard discs not formatted for “widescreen”, use of the 16:9 aspect ratio will result
in image distortion.
SPEAKER Menu
Speaker Menu Features
5ms
4ms
Center Control
3ms
2ms
1ms
Adjust the time difference between the center and
front speakers to create a time delay between
1 and 5 milliseconds, producing a more accurate
audio effect.
0ms
Rear Control
9ms
6ms
3ms
Adjust the time difference between the rear and
front speakers to create a time delay between 3
and 15 milliseconds, producing a more accurate
audio effect.
Down Sampling
Off
On
Surround
Subwoofer
0ms
Normal Output
Audio signal output at 48kHz
Center
NOTE: When Down Sampling is On, the audio output signal will be converted to 48kHz. When
Down Sampling is Off, the original sampling frequency is preserved.
DownMix
Large
Front
15ms
12ms
Full 6CH
Speaker Mode
6-channel mode
2-channel mode. If you select this mode, the
selections below will not be available.
Use when front speakers have good bass output.
Small
Use when front speakers do not have good bass
output.
Large
Use when rear speakers have good bass output.
Small
Use when rear speakers do not have good bass output.
None
Use when rear speakers are not present.
Present
Use when subwoofer is present.
None
Large
Use when subwoofer is not present.
Use when center speaker has good bass output.
Small
Use when center speaker does not have good bass
output.
None
Use when center speaker is not present.
Speaker Selection
Selecting LARGE for the multi-channel speaker option will give a full range output. Selecting
SMALL for the multi channel speaker option will activate a high pass filter whose crossover is
dependent upon the sub-woofer low pass filter frequency. For example, if the subwoofer low
pass filter is set to 80Hz, then the high pass SMALL speaker crossover will be set to 90Hz.
VIDEO Menu
VIDEO Menu Features
32
33
CD/MP3/WMA/JPEG Operation
Low pass
80Hz
120Hz
160Hz
High pass
90Hz
135Hz
180Hz
RATING (Parental Lock) Menu
The DVD system has a built-in parental lock feature to prevent unauthorized persons from
viewing restricted disc content. By default, the rating system is unlocked. Once setup, the
parental lock is released only by entering the correct password. Once the password is entered,
rating is available for setup.
RATING Menu Features
Password
----
Instructions for Insert/Eject, Play/Pause, Stopping Playback, Track Selection, Fast
Forward/Fast Reverse, Scan, and Random Play are the same for DVD, CD and MP3 operation.
Please see the DVD Player Operation section for information about these topics.
The file naming formats listed below are compatible with this unit:
• ISO 9660 – file name: 12 characters, file extension: 3 characters
• ISO 9660 – file name: 31 characters, file extension: 3 characters
• Joliet – 64 characters
If the file or folder name does not conform to ISO 9660 file system standards, it may not be
displayed or played back correctly.
CD Player User Interface
1
2
3
4
5
Enter a 4-digit password to activate the “Rating”
feature.
16
13
1. Kid Safe
17
14
2. G
3.PG
Rating
4. PG-13
5. PG-R
Select the appropriate rating level for the intended
audience. You may override higher ratings by using
your password.
18
15
19
6. R
7. NC-17
8. ADULT
No
Load Factory
Yes
Select “Yes” to restore the factory default settings
for the DVD setup only (except the password and
parental lock setting).
To reset the password, access the “RATING” menu and enter the current password. Once the
correct password is entered, you can access the “Password” field and enter a new one.
NOTE: Record the password and keep it in a safe place for future reference. The rating for each
disc is marked on the disc, disc packing, or documentation. If the rating is not available on the
disc, the parental lock feature is unavailable. Some discs restrict only portions of the disc and
the appropriate content will play. For details, please refer to the disc description.
34
6
7
8
9
10
11
12
1.Current source indicator, touch this area to access MAIN menu.
2.Disc title
3.Track title
4.Bluetooth indicator
5.Current time
6.
: Touch to play/pause
7.
: Touch to stop disc playback
8.
: Touch to turn to the previous page
9.
: Touch to turn to the next page
10.
: Touch to fast backward current track
11.
: Touch to fast forward current track
12.
: Touch to activate/deactivate Scan And you can press the (Title) button on the remote
control to toggle the scan function “on/off”
13.
: Touch to activate/deactivate Repeat Single Mode
14.
: Touch to activate/deactivate Random Mode
15.
: Touch to display the numeric keypad on the screen and then you can use the numeric
keypad to access a track directly.
16.Current track and total number of tracks on disc
35
17.Elapsed playing time
18.Playback information
19.Volume indicator
Playing CD Files
After inserting a CD disc, files will play in the sequence of the directory. In playing back, you can
press the numeric button on the remote control or touch a track on the onscreen directly to play.
Previous/Next Page
Touch the
or
on the screen to navigate through the pages/files.
Fast backward/fast forward
Touch the
or
on the screen to Fast backward or fast forward play.
MP3/WMA Discs
This player allows you to playback MP3/WMA files recorded on CDROM, CD-R, CD-RW,
DVD+R/RW and DVD-R/RW. For CD-RW discs, please make sure they are formatted using the
full method and not the quick method to prevent improper disc operation. Use the following
settings when compressing audio data for your MP3 disc:
• Transfer Bit Rate: 320kbps
• Sampling Frequency: 48kHz
When recording MP3 up to the maximum disc capacity, disable additional writing. For recording
on an empty disc up to maximum disc capacity, use the "Disc at once" setting.
7.
: Touch to stop disc playback
8.
: Touch to turn to the previous page
9.
: Touch to turn to the next page
10.
: Touch to display previous folder
11.
: Touch to display next folder
12.
: Touch to fast forward current track
13.
: Touch to activate/deactivate Repeat Single Mode
14.
: Touch to activate/deactivate Random Mode
15.
: Touch to display the numeric keypad on the screen, and use it to access a track directly.
16.The disc format indicator, displays the current track and total number of tracks on disc
17.Elapsed playing time
18.playback information
19.Volume indicator
Playing MP3/WMA Files
After inserting a MP3/WMA disc, files will play in the sequence of the directories/folders. In
playing back, you can press the numeric button on the remote control or touch the a track
directly to play.
Change Directory/Folder
Touch the
or
on the screen to navigate through the directories/folders.
Previous/Next Page
Touch the
or
on the screen to navigate through the pages/files.
The touch keys for MP3/WMA CD/DVD playback are described below.
JPEG Discs
1
2
3
4
5
16
13
17
14
18
15
19
6
7
8
9
10
11
1.Current source indicator, touch this area to access MAIN menu.
2.Disc title
3.Track title
4.Bluetooth indicator
5.Current time
6.
: Touch to play/pause
36
12
1
2
3
1.Stop playback and return to the picture list
2.Rotate picture clockwise 90°
3.Rotate picture counterclockwise 90°
37
SD Card Reader Operation
iPod Operation
Accessing SD Card Mode
Accessing iPod Mode
Open the main display panel, and you will find the SD Card slot. Insert the SD Card in the slot,
and press the SRC button on the front panel to switch to SD Card mode. You can press the
(SRC) button on the remote control to switch to the Can also touch the SD icon on the screen
Form the main menu.
1.To switch to iPod mode, press the SRC button on the front panel or the (SRC) button on the
remote control repeatedly until iPod appears at the top left corner of the screen.
2. Select the Main menu, then touch the iPod icon to select iPod as your source.
iPod Instructions
Using the Touch-Screen Controls
The touch keys on the screen for iPod playback are described below.
The touch keys for SD card playback are described below. The interface is similar to the
MP3/WMA mode.
1
2
3
4
1
2
3
4
5
5
19
16
13
20
14
13
17
14
15
16
17
18
21
18
15
22
19
6
6
7
8
9
10
11
12
1.Current source indicator, touch this area to access MAIN menu.
2.Folder title
3. Track title
4.Bluetooth indicator
5.Current time
6.
:Touch to play/pause
7.
: Touch to stop disc playback
8.
:Touch to turn to the previous page
9.
:Touch to turn to the next page
10.
: Touch to display previous folder
11.
: Touch to display next folder
12.
: Touch to fast forward current track
13.
: Touch to activate/deactivate Repeat Single Mode
14.
: Touch to activate/deactivate Random Mode
15.
: Touch to display the numeric keypad on the screen to access a track directly.
16. Current track /total tracks
17. Elapsed playing time
18. Playback information
19. Volume indicator
38
7
8
9
10
11
12
1.Current source indicator, touch this area to access MAIN menu.
2.Artist name
3.Track title / root directory list
4.Bluetooth indicator
5.Current time
6.
: Touch to play/pause disc playback
7.
: Touch to stop disc playback
8.
: Touch to turn to the previous page
9.
: Touch to turn to the next page
10.
: Touch to fast backward current track
11.
: Touch to fast forward current track
12.
: Touch to activate/deactivate Scan Mode
13.
: Touch to wait for iPod video/photo
14.
: Touch to activate/deactivate Repeat Single Mode
15.
: Touch to activate/deactivate Random Mode
16.
: Touch to access root directory list
17.
: Touch to display a numeric keypad on the screen to access a track directly.
18.
: Touch to display track list
19.Current track /total tracks
20.Elapsed playing time
21.Playback information
22.Volume indicator
39
Sat Radio Operation
According to the above instruction 16, when you press the
display The following.
button, the touch screen will
Accessing Sat Radio Mode
To switch to Sat Radio mode, press the SRC button on the front panel or the (SRC)
button on the remote control until SAT appears at the top of the screen. The touch keys for
Sat Radio playback are described below.
NOTE: An optional Terk XM Direct Universal Tuner box(XMD1000) and XM Antenna is required
to receive XM Radio, along with a subscription to XM Radio. Check with your dealer for these
Optional devices.
1
2
3
4
5
6
7
8
The TFT displays the root directory list classified by the iPod, from which you can select your
favorite songs.
You can choose a play list from your iPod play lists and then select a song to listen to.
9
18
10
Playback of video on iPod
For playback of video on iPod, press the
following.
button to enter, the touch screen will display the
11
If there are videos on iPod and you select them on iPod, they will start to play, otherwise there
will be nothing on the display. However, you can return to listen to your music by pressing the
button again.
NOTE: All video control functions are done on the iPod video, the touchscreen only controls
audio portions of iPod functionality.
12
13
14
15
16
17
1.Current source indicator, touch this area to access MAIN menu.
2.The artist information of the channel the playing back currently.
3.The preset channel Currently playing back.
4.Bluetooth indicator
5.Current time indicator.
6.Current Band and channel number indicator.
7.Current channel name indicator.
8.Current channel category indicator.
9.Playback information.
10.The volume indicator.
11.
: Touch to change among the following bands: SAT, SAT-1, SAT-2 and SAT-3.
12.
: Touch to open the category folder list.
13.
: Touch to scan the previous available channel of all categories.
14.
: Touch to scan the next available channel of all categories.
15.
: Touch to scan the previous available channel of current category.
16.
: Touch to scan the next available channel of current category.
17.
: Touch to activate/deactivate Scan Mode.
18.
: Touch to display the numeric keypad on the screen to access a channel directly.
Auto Scan
Touch the
40
button to automatically scan the available channels of all categories.
41
Bluetooth Operation
Manual Scan
Touch the
Touch the
Before using the Bluetooth
/
/
to scan the previous/next available channel of all categories.
to scan the previous/next available channel of current category.
Storing a Channe l
1. Select a band (if needed), then select a channel.
2. Touch and hold an on-screen preset channel for three seconds. The storing process is
complete.
Before using the Bluetooth, it’s necessary to perform the following steps. For more operating
details, refer to each section below.
1. Select the “Bluetooth” option in the General setup and select the “On” option to activate the
Bluetooth feature.
2. Pair your mobile phone to this unit (refer to the “Pairing” operation). It is necessary to pair
your phone to the unit. Without pairing, Bluetooth is not available.
The Bluetooth Indicator
Recalling a channel
12 numbered preset channels store and recall channels for each band. Front 6 stored channels
(1-6) for the current band appear on the screen, touch the channel directly or use the numeric
buttons on the remote control.
You can touch the arrow buttons (
) on the screen to select other channels.
There is a Bluetooth indicator (
) at the top of the touch screen.
When the Bluetooth function is “Off”, the indicator is grey.
When the Bluetooth function is “On” and no phone is connected to the unit, the indicator will
blink.
If a phone has been connected to the unit, the indicator is on solid.
Accessing Bluetooth Mode
Access the MAIN menu first and then touch the
button on the screen to access Bluetooth
mode.
Touch the
button at the top of the touch screen to access Bluetooth mode directly.
Bluetooth User Interface
Dial Interface
1
8
2
3
6
4
7
5
1.Current source indicator, touch this area to access MAIN menu.
2.Touch to access the dial interface.
3.Touch to access the Phone book.
4.Touch to access Bluetooth setup.
5.Touch to switch the audio output between the unit and the mobile phone.
6.Make use of these buttons to achieve some base functions of the phone.
42
43
7.Touch to return to the previous menu.
8.Show the phone number and function status.
Manual
Connect
Phone Book
Press the
Auto
button to access the Phone Book.
If this function is set to Auto, connection between
the Last Used phone and this unit will take place
automatically as soon as the devices are less than
a few meters apart.
Pairing
You can see phone book list, SIM book list, dialed call list, received call list, missed call list.
If the number has been stored in the Phonebook, it can be accessed by touching
or
on
the screen to navigate through the Phone Book entries. Then, touch the number to initiate the
phone call
NOTE: Not all Bluetooth enabled phones support this feature
Bluetooth setup
Select the
button to access the Bluetooth setup.
Access the Bluetooth setup and press “Yes” option on the screen, then “Wait pairing” displays on
the screen. Now you can pair a phone with the unit.
This unit can pair with 4 mobile phones in all, but just one can be active at a time.
The Default phone will be retained only if all other paired phones are deleted. (Default Phone:
The phone that was first paired with the unit.)
When maximum pairing has been completed, that is, four mobile phones have been connected
with the unit, and you want to still pair a new one, then the system will retain the default phone
and last used phone used. The phone least used (except the default phone) will be deleted and
the new paired phone will become the last used phone. (Last Used Phone: The phone connected
with the unit that was used last.)
If you want pair your phone with the unit, the password 1234 is used to complete the pairing.
When asked, enter this password in the phone you are pairing with this unit.
Auto Connect
If the unit has been set to auto connect, it will attempt to connect to the last used phone first. If
Auto Connect is not activated, the unit will return to the previous operating mode.
When the phone connects to the unit successfully, all of the cell phone’s Bluetooth enabled
options will be active.
Making a phone cal l
There are four ways to make a phone call from this unit:
1. Make use of the Number dial on the screen to make a call.
2. You can enter the phone number using the numeric keypad and press the OK button on the
remote control to make a call. (must be in the Bluetooth mode)
3. You can open the phone book and select one to make a call directly. (Your cell phone must
support this option)
4. If your phone supports voice dial, access this mode on your phone instead of using the
Phonebook
Answering an incoming call
LANGUAGE Menu Features
Pairing
Yes
Press the “Yes” button to start to wait for pairing
with one phone.
Off
Answer an incoming call manually.
On
The unit will automatically answer an incoming call
(based on the cell phone Bluetooth functions)
Auto Answer
44
You can answer an incoming call even if the source other than the telephone is selected.
You can answer an incoming call automatically or manually (refer to Bluetooth setup and the
Controls and Indicators title (Button Operation) for exact instructions)
When a call comes in, this interface will display on the screen:
45
Navigation Operation
Access the Navigation mode
1. Access the MAIN menu and select the NAVI button on the touch-screen to enter the
Navigation Operation interface.
2. Press the SRC button on the front panel or on the remote control to switch the source to
Navigation.
3. Press NAV button on the front panel of the unit.
Navigation Operation
Please read the Navigation Software User Manual
End a call
Press the ESC button on the remote or touch the
icon to end a call.
NOTE: Not all handsets are compatible with the Bluetooth hands free system. Please check the
compatibility list if you are experiencing connectivity problems. If you are experiencing
operation problems, please contact your installation center for assistance. You may have an
Incompatible handset and your unit is functioning normally.
IMPORTANT INFORMATION:
Make sure that the SD Card with the map information is inserted into the NAV-1 or NAV-2
navigation unit before installing in the vehicle. It may be hard to access this card slot once the
installation is completed.
Follow the instructions on loading mapping information from the DVD-ROM to the SD Card in the
Navigation Software User Manual. This must be done prior to loading the SD Card into the
Navigation Unit.
How to Listening to an Audio program while using/viewing the Navigation
You can listen to an audio program while using Navigation. To do so, do the following:
1. Select the audio source. The source can be the Tuner, Satellite Radio, iPod, SD
Card, or the audio from the AUX input.
2. Touch the NAV button on the front panel to select Navigation. The map will be
shown on the TFT display, and audio will continue to play while you are in the
Navigation mode.
3. Navigation voice prompts will mute the audio source, give the instruction, and then
return to the audio source
4. To adjust a parameter of the audio source (i.e., select a different radio station),
touch the NAV button. This will return you to the audio source screen. Make your
adjustments, and then press the NAV button to return the Navigation function.
Navigation will continue while you are in an audio source screen, and voice prompts
will continue while you make adjustments.
46
47
48
49
Increase volume level
Review wiring diagram and check “MUTE” connection
Replace speakers
Volume set too low
Improper “MUTE” connection
Speakers damaged
Check wiring and correct
Turn TFT Auto Open on
Check wiring and correct
Incorrect connection between yellow
memory wire and positive battery wire
TFT Auto Open is turned off
Incorrect connection to parking brake wire
Unit resets itself when
engine is off
Monitor does not open
automatically
Use disc in good condition
Clean disc with soft cloth
Use compatible disc
Disc is dirty or wet
Incorrect playback
message displayed
Interruption occurred
during playback
Recreate disc with good files
File is damaged/bad recording
Message is longer than LCD can display
Clean disc or replace
Turn PCB off
Use original disc
Disc is dirty or scratched
PCB is on
No repeat or searching
while playing VCD
MP3
PCB is not available on the disc
PBC cannot be used
during VCD playback
Insert disc with label side up
Disc is inserted upside down
Disc is illegally copied
Use disc with proper region cod
Disc region code is not compatible with unit
Disc rating exceeds Parental Lock rating limit Change Parental Lock settings to lower restriction
Incompatible disc is used
Eject current disc and insert new one
Disc is warped or scratched
Turn LOCAL function off
Disc already inside unit
Connect the auto antenna control cable properly
LOCAL function is activated
Connect the auto antenna control cable properly
Auto antenna not properly connected
Auto antenna is not fully extended
Press OPEN key to restart monitor movement
Use correct aspect ratio setting
Improper aspect ratio setup
Moving path is blocked
Check wiring and correct
Improper video signal connections
Image blurred, distorted,
or dark
Disc does not play back
Cannot insert disc
DISC
Weak station searching
TUNER
Monitor stops at incorrect
position
Prolonged image or
improper height/width ratio
display
No image
Stop vehicle in safe place and apply parking brake
Check that “MUTE” connection is not grounded and
that it’s properly insulated
“MUTE” wire is grounded
Tel-Mute malfunction
PRK SW is activated and parking brake
is not engaged
Check speaker connections
TFT MONITOR
Connect proper speakers
Speaker is shorted
Use original copy
Insulate all speaker wiring connections
Check wiring and correct
Improper audio output connection
Adjust the channel balance to the center position
Remove battery and install correctly
Battery installed incorrectly
Speaker wiring is in contact with metal
part of car
Replace battery with new one
Battery depleted
Heavily biased volume balance
Press the RESET button located in the bottom right
corner of the front panel
Install new fuse with correct rating
Install new fuse with correct rating
Corrective Action
Illegal operation
Radio Fuse blown
Car battery fuse blown
Cause
Unauthorized disc is in use
Speaker power rating not compatible with unit
Poor sound quality or
distortion
No/low audio output
Remote control does not
function
Unit will not power on
GENERAL
Provlem
Clean disc with soft cloth
Insert disc with label side up
Disc is dirty
50
Remote control does
not function
Pull out the insulation tape
Replace battery with new one
Remove battery and install correctly
Battery depleted
Battery installed incorrectly
illegal mechanism operation
Error
Battery is covered with insulation tape
DVD is not compatible with region code
of unit
Region Error
Remote control
Disc format is not compatible with this unit
Press EJECT key for 5 seconds to reset loading
mechanism
Insert disc
Disc not present in loading compartment
Disc is upside down
Clean disc with soft cloth
Insert disc with label side up
Corrective Action
Disc is upside down
Disc is dirty
Cause
Disc is being read
Unknown disc
Bad Disc
No Disc
Loading
Error Messages
Messages Displayed
1. When using the remote for the first time, you must pull out the insulation tape.
2. Remove the battery if the remote control is not used for a month or longer.
Remove and dispose of the old battery immediately.
Do not store the battery with metallic materials.
3. Inserting/Replacing the Battery:
Remove the battery holder
Remove the battery from the battery holder
Install the battery
51
Specifications
Power Ratings
Main Amplifier
Power Output: 20 watts X 4 channels into 4-ohms @ < 10% THD+N
Signal to Noise Ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms)
MAX Power: 50 X 5 watts into 4-ohms, all channels driven
Frequency Response: 20Hz to 20kHz, -3dB. Aux input used as source reference
Reference Supply Voltage: 14.4VDC
DVD/CD Player
Compatible formats: DVD-R, DVD-RW, DVD+R, DVD+RW,
CD-R, CD-RW, CD-DA, MP3, WMA, HDCD, SVCD, VCD,
MPEG, JPEG, MP3/WMA files burned onto a DVD+R/W or
DVD-R/W and CD-R/RW
Signal to Noise Ratio: 85dBA
Dynamic Range: >95dB
Frequency Response: 20Hz to 20kHz, -3dB
Channel Separation: > 60dB @ 1kHz
D/A Converter(s): 6-channel high performance 24-bit, 192kHz, multi-bit Sigma Delta modulation.
DAC supports sample rates from 8~192kHz.
Mechanical anti vibration ability: 10~200Hz, X/Y/Z direction: 1.0G
Insert the battery holder
NOTE: Use only one CR2025(3V) lithium battery.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
Do not recharge, disassemble, heat or dispose of the battery in fire.
Keep batteries away from children to avoid the risk of accident.
Suggestions
1. Only use a piece of clean silicone cloth and neutral detergent to clean the front panel or
monitor. A rough cloth and non neutral detergent (such as alcohol) may result in scratching or
discoloration.
2. Keep off water and other liquid things.
3. If the temperature inside the player gets too high, a protective circuit automatically stops
playing the disc. And then, please wait for the unit to cool down before operating the player
again.
4. Never insert anything other than a 5” (12 cm) compact disc into the player as the mechanism
can be damaged by foreign objects.
5. Do not attempt to use a 3” (8 cm) CD-Single disc in this unit, either with or without an adaptor,
as it will damage the player and disc. Such damages are not covered by the Warranty on this
product. 6.When the vehicle warms up during cold weather or under damp conditions,
condensation may appear on the LCD panel. If this occurs, the screen will not operate properly
until the moisture has evaporated.
7.We suggest that you should clean the discs used in this unit more frequently than used in your
home, because of the environmental conditions of the vehicle.
52
Video Section
Format: NTSC, PAL (auto-detection)
Output: 1Vp-p (75-ohm), buffered
Input: 1Vp-p (75-ohm)
FM Tuner Section
Tuning Range: 87.5MHz - 107.9MHz
Mono Sensitivity (-30dB): 10dBu
Quieting Sensitivity (-50dB): 15dBu
Alternate Channel Selectivity: 70dB
Signal to Noise Ratio @ 1kHz: 58dB
Image Rejection: 60dB
Stereo Separation @ 1kHz: 30dB
Frequency Response: 30Hz - 15kHz, -3dB
AM Tuner Section
Tuning Range: 530kHz - 1710kHz
Sensitivity (-20dB): 20dBu
Signal to Noise Ratio @ 1kHz: 50dB
Image Rejection: 60dB
Frequency Response: 50Hz - 2kHz, -3dB
Integrated SD Card Reader
53
Monitor Section
Screen Size: 6.5" (Measured diagonally).
Screen Type: TFT Liquid Crystal Display (LCD) active matrix
Response Time: 30mSec rise time, 50mSec fall time
Resolution, DVD/Composite Video in: 280,800 sub pixels,
1200 (W) X 234 (H)
Viewing angle:
55-60 degrees left or right
35-40 degrees up
50-55 degrees down
General
Auxiliary Input impedance: 10k
Power Supply: 10.5 to 16V DC, negative ground
Fuse: 10-amp, mini ATM type
DIN chassis dimensions: 178mm x (160+25)mm x100mm
* Specifications subject to change without notice.
54
Download PDF

advertising