Downloaded From WashingMachine-Manual.com Manuals
Problem
The door can not open :
Spinning starts late or the laundry
is not spun enough :
Possible cause
The program is still running and the drum is turning.
The door lock has not yet released.
The water level is above the bottom edge of the door.
The machine is heating the water, and the water
temperature is higher than 55
The door can only be opened when the relevant light
has gone out.
The electronic unbalance detection device has cut
in because the laundry is not evenly distributed in
the drum.The laundry is redistributed by reverse
rotation of the drum.This may happen several times
before the unbalance disappears and normal spinning
can resume.if ,after few minutes,the laundry is still
not evenly distributed in the drum,the machine will
spin at a lower speed or will not spin.If at the end of
the programme the laundry is not spun enough,
redistriute the load manually and select the spin
programme.
Water is not
visible in the machine? The machine,
which is the result of modern technology, runs
in a very economical way with low water
consumption.Performanceis
neverthelessexcellent.
The machine makes an unusual
noise? The machine is fitted with a commutator
motor which improves machine
performance.
If you are unable to identify or solve the problem,contact our service centre. Before telephoning, make a note
of the model, serial number and purchase date of your machine: the Service Centre will require this information.
Contents of this user manual may be modified without informing you.
22
Downloaded From WashingMachine-Manual.com Manuals
1
Something not working?
3
14
15 - 17
4
18
4
Problems which you can resolve yourself
During machine operation it is possible that one of the End light starts to flash:
- E10:problem with the water supply
- E20: problem with the water draining
- E40:door open
Once the problem has been eliminated, press the START/PAUSE button to restart the programme. If
after all checks, the problem persists, contact your local Service Centre.
4
19
5
19
19
19
19
20
20
20
5
5
5
6
6
7
7
Problem
The machine does not start up:
The door is not firmly closed. E40
The machine is not plugged in or there is no power at
the socket.
The main fuse or the fuse in the plug has blown.
The START/PAUSE button has not been pressed.
The DELAY option has been selected.
The machine does not fill:
The
The
The
The
The machine fills them empties
immediately:
The end of the drain hose is too low. Refer to relevant
paragraph in drainage section.
21-22
7
7
8
The machine does not empty and/or
does not spin:
8
8
12
12
12
12
12
12
12
13
13
2
Downloaded From WashingMachine-Manual.com Manuals
Possible cause
water tap is closed. E10
inlet hose is squashed or kinked. E10
filter in the inlet hose is blocked. E10
door is not properly closed. E40
The drain hose is squashed or kinked. E20
The drain pump is clogged. E20
The laundry is not evenly distributed in the drum.
The RINSE HOLD or NIGHT CYCLE option has been
selected.
There is water on the floor:
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose ; check to see if it is
damp.
The drain hose is damaged.
Check that the filter has been fastened.
Unsatisfactory washing results:
Too little detergent or unsuitable detergent has Been
used.
Stubborn stains have not been treated prior to washing.
The correct program or temperature was not selected.
Excessive laundry load.
The machine vibrates or is noisy:
The transit bolts and packing have not been removed.
The support feet have not been adjusted.
The laundry in drum has not been evenly distributed.
Too little laundry is washed.
21
6. Emergency emptying out
Remove any objects from the pump impeller by
rotating it.
If the water is not discharged , proceed as follows to
empty out the machine:
Pull out the plug from the power socket;
Close the water tap;
If necessary, wait until the water has cooled down;
Open the pump door;
Place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove
its cap. The water should drain by gravity into the
bowl.Whe the bowl is full,put the cap back on the
hose. Empty the bowl. Repeat the procedure until
water stops flowing ou;
Clean the pump if necessary as previously described.
Replace the emergency emptying hose in its seat
after having plugged it.
Screw the pump again and close the door.
Put the cap back on the emergency emptying hose
and place the latter back in its seat.
7. Frost precautions
Screw the pump fully in.
Close the pump door.
If the machine is installed in a place where the temperature could drop below 0 , proceed as follows:
Remove the plug from the socket.
Close the water tap and unscrew the water inlet hose
from the tap.
Place the end of the emergency emptying hose and
that of the inlet hose in a bowl placed on the floor
and let water drain out.
Screw the water inlet hose back on and reposition the
emergency emptying hose after having put the cap
on again.
5. Water inlet filter
If you notice that the machine is taking longer to fill,
check that the filter in the water inlet valve is not
blocked:
Turn off the water tap.
Take off the inlet hose from water tap. Drain water in
this hose.
Unscrew the hose from the inlet valve.
Clean the filter with a stiff brush.
Put on the hose back onto the tap and the inlet
valve.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.When
you use the machine again, make sure that the ambient temperature is above 0 .
20
Downloaded From WashingMachine-Manual.com Manuals
3
Maintenance
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the drawer
after cleaning.
1. Door seal
Check from time to time the door seal and eliminate
eventual possible objects that could be trapped in the
fold.
PE
PS
PP
4. Drain pump
The drain pump should be inspected if
The machine does not empty and/or spin.
The machine makes an unusual noise during draining
due to objects such as safety pins,coins etc.
blocking the pump.
Proceed as follows
Disconnect the appliance.
If necessary wait until the water has cooled down.
Open the pump door.
2. Bodywork
Clean the outside of the machine with warm water and
a neutral, non-abrasive household detergent. Rinse
with clean water and dry with a soft cloth.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
3. Detergent dispenser drawer
After a while, detergents and fabric softeners leave
deposits in the drawer.
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the machine,
press the button in the rear left-hand corner.To facilitate cleaning, the top part of the additive compartment can be removed.
Place a container close to the pump to collect any
spillage.
Release the emergency emptying hose, place it in
the container and remove its cap.
When no more water comes out, unscrew the pump
and remove it. Always keep a rag nearby to dry up
spillage of water when removing the pump.
85 cm
60 cm
49 cm
5
2
2
1
2
EWS1050
EWS1250
EWS1250Z
kg
kg
kg
kg
kg
1000
1200
1200
AC 220V/50Hz
2000 W
10A
0.05MPa
0.8MPa
4
Downloaded From WashingMachine-Manual.com Manuals
19
Programme table
Type of laundry
and symbols on
labels
60
95
white cotton:
Programme/
temperature
Cottons
60-95
e.g. : work clothes,
sheet,household
7
Description of
programme
Wash at 60-95
three rinses
long spin
linen, table cloth
60
30
Coloured cotton:
e.g.shirts,blouse
underwear towels
household linen
60
30
Synthetic
fabricand
blends:
e.g.shirts,blouse,
underwear
40
30
Delicate fabric
e.g. acrylic fabric,
Cottons
Wash at 60-30
60-30
cold
or cold
three rinses
long spin
Synthetic
60-30
cold
Short spin
Delicates
40-30
cold
viscose, polyester,
synthetic blends
40
30
Wool, h a n d
wash
Wool/Hand
wash
40 - 30
cold
silk
Silk
Wash at 60-30 ,
or cold
three rinses
30
cold
Wash at 40-30 ,
or cold
three rinses
Short spin
Wash at 40-30 ,
or cold
three rinses
Short spin
Wash at 30 ,
or cold
three rinses
Available options
Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse
Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse
Max load
5Kg
1
5Kg
Spin speed
Rinse hold
Night cycle
Economy
Super Quick wash
Prewash
Anti-allergic rinse
2Kg
Spin speed
Rinse hold
Night cycle
Super Quick wash
Prewash
Anti-allergic rinse
2Kg
2
3
A
B
Spin speed
Rinse hold
Night cycle
1Kg
Spin speed
Rinse hold
Night cycle
2Kg
A
4
B
C
Short spin
5
6
18
Downloaded From WashingMachine-Manual.com Manuals
5
B
60
90cm
If you had selected the RINSE HOLDor NIGHT CYLCE
option , the light of the START/PAUSE button goes out,
the zero on the display begins to flash, the door is
locked and RINSE HOLD or NIGHT CYCLE light remains lit.
When the programme has been completed, a blinking
zero appears on the display and the audible signal is
given.
Press the SKIP RESET button repeatedly to erase
the programme that has just been carried out. If
you omit to do this, the next time you switch the
washing machine on, the blinking zero will appear on the display and you will hear the audible
signal.
Press the ON/OFF button to switch the machine off.
The relevant light will go out. Remove the laundry
from the washing machine. Check whether the drum is
completely empty, by rotating it with your hand. The
purpose of this is to prevent any items of laundry
from remaining accidentally in the drum, where they
might get damaged in a subsequent wash (e.g. by
shrinking) or bleed colour into another load of laundry.
We advise you to close the water supply tap and
disconnect the plug from the socket. Leave the door
ajar in order to air the washing machine.
12. How to cancel a programme during its cycle
To cancel a programme that is being carried out, first
pause the washing machine by pressing theSTART/
PAUSE button, then press the SKIP RESET button
repeatedly, until the display shows three blinking
dashes.
13.How to Open the door during the
cycle of a programme
220V/50Hz
You can open the door, after having set the washing
machine to PAUSE, provided the following conditions
exist:
The washing machine is not in the heating phase
beyond 55°C;
The level of the water is not high;
The drum is not turning.
If these requirements are met, when you pause the
washing machine, the door can be opened instantly.
Should it not be possible to open the door, and should
it be absolutely necessary to do so, switch the machine off by pressing the ON/OFF button. After approximately 3 minutes, you can open the door instantly.
Pay attention to the level and temperature of the
water in the washing machine!
When you close the door and press the ON/OFF button again, the washing machine will resume the
programme from the point where it had been interrupted.
14. End of programme
At the end of the programme, the washing machine
stops automatically, gives an audible signal, and displays a blinking zero.
60cm
6
Downloaded From WashingMachine-Manual.com Manuals
17
Important!
Every programme has its limited temperature in order
to preventing laundry from being spoiled,so it’s normal
that some temperature can not be chosed.
delay. The selected delay time value (up to 23 hours)
will appear on the display for 3 seconds, then the
duration of the programme will appear again.
7. Select the SPIN SPEED or the RINSE
HOLD option
Press the SPIN SPEED button repeatedly, in order to
select the desired spin speed or the RINSE HOLD
option. The relevant light will light up. If you select the
RINSE HOLD option, the machine will stop at the end
of the programme with the water still in the tub.
10. Start the programme
Press the START/PAUSE button. The relevant light will
stop flashing and only the light relevant to the phase
that is in progress will remain lit. If you have chosen a
delayed start, the washing machine will begin the countdown The display will show the duration of the
programme or the selected delay.
Important!
Every programme has its limited spin speed in order to
preventing laundry from being spoiled,so it’s normal
that some speed can not be chosed.
1
8. Select the desired options
2
If your laundry is very dirty or has stubborn stains, it
may be advisable to select the PREWASH, ANTIALLERGIC RINSE option. Press the OPTIONS button
so as to cause one or both of the lights to light up. If
your laundry is only slightly soiled, depress ECONOMY
or SUPER QUICK WASH button. The relevant light
illuminates.
3
11. How to change a programme during its cycle
Before you make any change, you must pause the
washing machine by pressing the START/PAUSE
button. It is possible to change any phase before the
programme carries it out.
Changing the type of fabric or temperature is possible,
obviously, only during the washing phase.
If it is necessary to drain the water in order to change
the programme in progress,proceed as follows:
PAUSE the machine by pressing the START/PAUSE
button;
Press the SKIP RESET button repeatedly, until only
the DRAIN light remains lit;
Press the START/PAUSE button again.
When the water has been drained, the display shows a
blinking zero. You may now select a new programme
and press the START/PAUSE button to start it.
9.Select the DELAY START
Before you start the programme, if you wish the
starting to be delayed, press the DELAY START button
repeatedly, or keep it pressed, to select the desired
16
Downloaded From WashingMachine-Manual.com Manuals
4
5
6
7
Operating sequence.
Before washing your first load of laundry we recommend that you run a cotton cycle at 60 with the
machine empty, in order to remove any manufacturing residue from the drum and tub.
1. Place the laundry in drum
5. Select the desired programme/
fabric
Open the door.
Place the laundry in drum, one item at a time,shaking
them out as much as possible.
Close the door.
1 2
3
4
5
6
8
7
9
Press the FABRICS button repeatedly, in order to
select the desired programme/fabric. The relevant light
will light up. The lights relevant to the phases that form
the programme will light up. The display will show the
duration of the selected programme, calculated on the
basis of the maximum load for each type of fabric.
The light of the START/PAUSE button will start flashing.
If the load of laundry to be washed is small, at the
beginning of the cycle the display will still indicate the
duration relevant to the maximum load. The duration
value will be gradually adjusted during the execution of
the cycle.
10 11 12
1
/
2. Measure out the detergent
5
Pull out the dispenser drawer until it stops. Measure
out the amount of detergent recommended by the
manufacturer in a graduated cup and pour it into the
main wash compartment.
If you wish to carry out the prewash, pour detergent
into the appropriate compartment marked.
2
/
3. Measure out the additives
3
If required, pour fabric softener into the compartment
marked, without exceeding the MAX mark.
6. Select temperature
Press the TEMPERATURE button if you wish to select
a temperature value different from the one proposed
by the washing machine. The relevant light will light up.
/
4
4. Switch the machine on
To switch the machine on, press the ON/OFF button :
the mains-on light comes on. The display will show
three blinking dashes or a blinking zero.
/
8
Downloaded From WashingMachine-Manual.com Manuals
/
15
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Energetic
wash
6-7
95
60
40
30
Max. wash
temperature
95 C
Max. wash
temperature
60 C
Max. wash
temperature
40 C
Max. wash
temperature
30 C
Delicate wash
60
40
40
8
/
Do not
wash
at all
Hand wash
30
/
/
cI
Bleaching
Do not bleach
Bleach in cold water
/
/
/
/
lroning
Dry cleaning
Hot iron
max 200 C
Warm iron
Lukewarm iron
max 150 C
max 110 C
A
P
F
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not iron
-
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On clothes
hanger
On the line
14
Downloaded From WashingMachine-Manual.com Manuals
Tumble dry
Do not
tumble dry
9
9
0
/
Ink: depending on the type of ink, moisten the fabric
first with acetone ( ), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
( ) do not use acetone on artificial silk.
Quantity of detergent to be used
The type and quantity of detergent will depend on the
type of fabric, load size, degree of soiling and hardness of the water used.
Water hardness is classified in so-call degree of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Follow the product manufacturer’s instructions on
Detergents and additives
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances, which ,
in large quantities, can upset the delicate balance of
nature.
The choice of detergent will depend on the type of
fabric (delicates,woollens ,cottons ,etc.), the colour,
washing temperature and degree of soiling.
All commonly available washing machine detergents
may be used in this appliance:
/
10
/
-
10
Downloaded From WashingMachine-Manual.com Manuals
- You are washing a small load,
- The laundry is lightly soiled,
- Large amounts of foam forms during washing.
- Powder detergents for all types of fabric,
- Powder detergents for delicate fabrics ( 60
0
Err
quantities to use.
Use less detergent if:
/
/
max)
and woollens.
- Liquid detergents,preferably for low temperature
wash program ( 60 max )for all types of fabric,or
special for woollens only.
The detergent and any additives must be placed in the
appropriate compartments of the dispenser drawer before starting the wash program.
If using concentrated powder or liquid detergents, a
program without prewash must be selected.
The washing machine incorporates a recirculation
system, which allows an optimal use of the concentrated detergent.
Pour liquid detergent into the dispenser drawer compartment marked
just before starting the program.
Any fabric softener or bleacher must be poured into
the compartment marked
before starting the wash
program.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the “MAX”
mark in the detergent dispenser drawer.
13
Laundry weight
Washing hints
The following weights are indicative:
Bathrobe
Napkin
Quilt cover
Sheet
Pillow case
Tablecloth
Towelling towel
Tea cloth
Night dress
Ladies’ brief
Man’s work shirt
Man’s shirt
Man’s pyjamas
Blouse
Men’s underpants
Sorting the laundry
Follow the wash code symbols on each garment label
and the manufacture’s washing instructions.
Sort the laundry as follows:
Whites, coloureds , synthetics, delicates, woolens.
Temperatures for washing
95
60
cold
30 -40
for dirty white cottons and linen(e.g. tea
cloths,towels,tablecloths,sheets)
for normally soiled,colour fast garments(e.
g. shirts,night dresses,pyjamas….) in linen,
cotton or synthetic fibres and for ligntly
soiled white cotton (e.g. underwear).
for delicate items (e.g. net curtains),
mixed laundry including synthetic fibres and
woolens.
1200g
100g
700g
500g
200g
250g
200g
100g
200g
100g
600g
200g
500g
100g
100g
-
/
-
/
/
/
/
/
/
/
/
/
12
Removing stain before washing
Stubborn stains may not be removed by just water and
detergent. It is therefore advisable to treat them prior
to washing.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special detergent
then rub in the soap and water.
Oil based paint: moisten with benzine stain remover,
lay the garment on a soft cloth and dab the stain; treat
several times.
Dried grease stains: moisten with turpentine, lay the
garment on a soft surface and dab the stain with the
fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a rust removing product used cold. Be careful with rust stains
which are not recent since the cellulose structure will
already have been damaged and the fabric tends to
hole.
Mould stains: treat with bleach, rinse well (whites and
fast coloureds only).
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Ball point pen and glue: moisten with acetone ( ),
lay the garment on a soft cloth and dab the stain.
Lipstick: moisten with acetone( ) as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Red wine: soak in water and detergent, rinse and treat
with acetic or citric acid, then rinse. Treat any residual
marks with bleach.
Checking Laundry
Important! Make sure that no metal objects are left in
the laundry (e. g. hair clips, safety pins, pins).
Never wash whites and coloureds together. Whites
may lose their whiteness in the wash.
New coloured items may run in the first wash; they
should therefore be washed separately the first time .
Button up pillowcases, close zip fasteners, hooks and
poppers. Tie any belts or long tapes.
Remove persistent stains before washing. Rub particularly soiled areas with a special detergent or detergent paste.
Treat curtain with special care, remove hooks or tie
them up in a bag net.
Maximum loads
Recommended load are indicated in the programme
charts.
General rules:
Cotton ,linen: drum full but not too tightly packed;
Synthetics: drum no more than half full ;
Delicate fabrics and woollens: drum no more than
one third full .
Washing a maximum load makes the most efficient
use of water and energy .
For heavily soiled laundry , reduce the load size.
12
Downloaded From WashingMachine-Manual.com Manuals
-
/
11
3
/
11
1200
100
700
500
200
250
200
100
200
100
600
200
500
100
100
95
60
30 -40
g
g
g
g
g
g
g
g
g
g
g
g
g
g
g
In this case,both the drain and the spin (at the speed
provided for the selected type of fabric) will be
performed. This button allows you also to select special programmes, such as RINSES, SPIN and DRAIN.
If the machine is already switched on because it
has just performed a washing programme, proceed
as follows:
- depress SKIP RESET once or repeatidly to cancel
the previously performed programme (three blinking
dashes will appear on the display);
- select the type of fabric by means of the relevant
button;
- select the special programme:
RINSES
Depress SKIP RESET once, the pilot light WASH goes
out.
SPIN
Depress SKIP RESET twice, the pilot lights WASH
and RINSES go out.
DRAIN
Depress SKIP RESET three times, the pilot lights
WASH, RINSES and SPIN go out and only the pilot
light DRAIN remains lit.
Example:
The time value shown on the display will decrease by
one unit every hour till the first 2 hours, and then it
decreases by one unit every 30 minutes.
You can change the delay time at any moment,
before you press the START/PAUSE button. If you
have already pressed the START/PAUSE button, and
you wish cancel the delay time, proceed as follows:
set the washing machine to PAUSE by pressing the
START/PAUSE button;
press the DELAY START button twice, to erase the
delay time. The display will indicate “0”.
press the START/PAUSE button again.
Important!
The door will be locked throughout the delay time. If
you need to open the door, you must first set the
washing machine to PAUSE by pressing the START/
PAUSE button. After you have closed the door, press
the START/PAUSE button again.
12. Programme phase indicator lights
When you select a programme, the lights relevant to
the phases that form the programme light up.
After you have started the programme, only the light
relevant to the phase that is currently being carried out
will remain lit.
In this case the machine will perform the rinses and
spin.
If the machine is switched off:
- depress ON/OFF button to switch it on;
- select the type of fabric by means of the relevant
button;
- select the special programme as previously
described.
11. DELAY START button
This button makes it possible to delay the starting of
the programme by up to 23 hours.For example, if you
want to take advantage of low energy price rates during nighttime. The delay you have selected is shown
on the display for about 3 seconds; afterwards, the
duration of the programme reappears. You must select this option after you have set the programme and
before you press the START/PAUSE button.
12
Downloaded From WashingMachine-Manual.com Manuals
11
The washing machine has completed the
programme: this is indicated by a blinking zero.
The zero will reappear when you switch the washing
machine on, unless the previous programme has
been erased by means of the SKIP RESET button.
An alarm code indicates a fault in the machine operation .
9. START/PAUSE button
This button has two functions:
Start: after you have selected the desired programme
and options, press this button to start the washing
machine. The light above the button will stop flashing and remain lit. If you have selected a delay time
by means of the relevant button, the countdown will
begin and will be shown on the display.
Pause: when you press this button again, the
programme in progress is interrupted. (you can add
missing clothes).The light above the button will start
flashing. To restart the programme, press the button
again.
Important!
You must set the washing machine to PAUSE before
you make any change in the programme in progress.
Important!
The first time you use the washing machine, when
you switch it on, it may display a blinking zero and
give an audible warning signal. This is due to the fact
that the washing machine has performed a washing
cycle during the manufacturer’s inspection tests, and
this cycle has not been erased after its completion.
Delay start, a time value indicated in hours and
selected by means of the relevant button. The delay
time is displayed for 3 seconds, then the duration of
the selected programme reappears. After you have
pressed the START/PAUSE button, the countdown
begins, and the delay time value decreases by one
unit every hour till the first 2 hours, and then it
decreases by one unit every 30 minutes. You can
delay the start of every programme selecting the
DELAY START button. The delay time is indicated
first by 30-60-90 minutes, and then by hours up to
23 hours.
10. SKIP/ RESET button
At the end of a programme, you must press this button once or repeatedly, in order to clear the contents
of the memory (the display will show three blinking
dashes); otherwise, the next time you switch the washing machine on, the blinking zero will reappear and the
audible warning signals relevant to the end of the previous cycle will be given. You can also press the SKIP
RESET button to exclude one or several phases of the
programme which is running, as indicated below: - set
the washing machine to PAUSE by pressing the START/
PAUSE button (the relevant light will flash);
- press the SKIP RESET button once or several times,
until the required phase(s) is(are) cancelled.
Example:
An incorrect option selection has been made:
this is indicated by the message Err when a function
incompatible with the current programme is selected.
The incorrect selection is also indicated by an audible warning signal.
10
Downloaded From WashingMachine-Manual.com Manuals
13
drain and spin:
PREWASH: select this option if you wish your laundry to be prewashed before the main wash (not
available for WOOL / HAND WASH and silk
programme).
The prewash ends with a short spin in programmes
for cotton and synthetic fabrics, whereas in the
programme for delicate fabrics the water is only
drained. The PREWASH and the ANTI-ALLERGIC
RINSE functions cannot be selected together.
ANTI- ALLERGIC RINSE:can be used with all
programmes except the WOOL / HAND WASH and
SILK programme. The machine adds rinses with
more water to remove residual detergent.
This option is recommended for people who are allergic
to detergents and in areas where the water is very
soft.
- press the FABRICS button to select the type of
95
95 C
60
40
60 C
60
30
40 C
40
40
30 C
30
fabric previously washed, eventually reduce the spin
speed, and then press the SKIP RESET button twice,
so as to cause the light SPIN to light up, then select
spin speed and at the end press the START/PAUSE
button.
Important!
When the machine is on, if you simultaneously press
the TEMPERATURE button and SPIN SPEED button
for about 3 seconds, the acoustic warning signal can
be activated or desactivated.
6-7. OPTIONS buttons
cI
200 C
150 C
110 C
A
P
F
R113
R111
R113
14
Downloaded From WashingMachine-Manual.com Manuals
Press this button to select the following options:
NIGHT CYCLE: when you choose this option, the
machine will not drain the water of the last rinse, so
as not to wrinkle the laundry. As all spinning phases
are suppressed, this washing cycle is very noiseless and it can be selected at night or in times with a
more economical power rate. On cotton and synthetic programmes the rinses will be performed with
more water. At the end of the cycle, the light of the
START/PAUSE button goes out and the door is locked,
the NIGHT CYCLE pilot light remains lit, to indicate
that the water must be drained. To complete the
cycle, choose one of the following programmes:
Drain To drain the water select DRAIN programme
by means of the SKIP/RESET button, then press
the START/PAUSE button.
Spin To spin the laundry choose SPIN programme
by means of the SKIP/RESET button; select spin
speed by means of SPIN SPEED button and then
press the START/PAUSE button.
ECONOMY: this option is available only with cotton
programme at 95°-60°-40° C and synthetics
programme at 60°-40° C. If you select this option
the temperature automatically decreases and,
consequently, the washing time increases. This function can be used with normally soiled laundry in order
to save energy.
SUPER QUICK WASH; select this function for laundry that is only slightly soiled (not for silk WOOL
and HAND WASH programme). The washing time
will be reduced according to the type of fabric and
the selected temperature.Special 23 minutes super
quick cycle is available by choosing “cold” and pressing this button.
The NIGHT WASH, the ECONOMY and the SUPER
QUICK WASH functions cannot be selected together.
8. Dispiay
The following pieces of information are shown on the
display:
Three blinking dashes, when a programme is cancelled by means of the SKIP RESET button. The
three blinking dashes will also appear when you press
the ON/OFF button to switch the machine on, if the
previously selected cycle has been erased.
Duration of washing programme in hours and
minutes, after you have selected a programme. While
the programme is running (after you have pressed
the START/PAUSE button), the displayed time value
decreases by one unit every minute.
The washing machine has stopped with water in
tub, at the end of a programme with RINSE HOLD
or NIGHT CYCLE option: this is indicated by a
blinking zero.
9
Use
Control panel description
5
1
1 2
3
4
5
6
1. ON/OFF button
7
8
9
10 11 12
Sterilization 95 option can hold high temperature for
10 minutes, in order to eliminate microphyte from the
laundry
By selecting position COLD the machine will wash with
cold water. To be used for extremely delicate items,
such as curtains.
Press this button to switch the washing machine on.
Press the ON/OFF button again to switch the machine
off.
2. MAIN-ON light
This light is connected to the ON/OFF button. It lights
when you press the button, and goes out when you
press it again.
5.SPIN SPEED button
Press this button repeatedly to change the spin speed,
if you want your laundry to be spun at a speed different from the one proposed by the washing machine.
The relevant light will light up.
Maximum speeds are:
for cotton: 1.200 rpm;
(EWS1050 1000rpm)
for synthetic fabrics, wool, and fabrics to be handwashed: 900 rpm;
for silk and delicate fabrics: 700 rpm.
RINSE HOLD position : when you choose this option,
the machine will not drain the water of the last rinse, so
as not to wrinkle the laundry. At the end of the cycle,
the light of the START/ PAUSE button goes out, the
door is locked, and the RINSE HOLD light remains lit,
to indicate that the water must be drained.
To complete the cycle, first press the SKIP RESET
button (3 dashes appear on the display), and then
choose one of the following options:
drain only:
- press the FABRICS button to choose any type of
fabric, press the SKIP RESET button 3 times, so as
to cause the light DRAIN to light up, and then press
the START/PAUSE button.
3. FABRICS button
Press this button repeatedly to select the programme
on the basis of the type of laundry to be washed. The
light relevant to the selected programme will light up.
The washing machine will propose a temperature and
automatically select the maximum spin value provided
for the programme you have chosen. You can change
these values by operating buttons 4 and 5. On the
display will appear the duration of the washing
programme, depending on the maximum load capacity
for each type of fabric, and the START/PAUSE light
begins to flash.
Hand wash
When you select this programme, you obtain a particularly delicate washing, suitable for articles of clothing whose label indicates that they must be handwashed .
4.TEMPERATURE button
Press this button repeatedly to increase or decrease
the temperature, if you want your laundry to be washed
at a temperature different from the one proposed by
the washing machine. The relevant light will light up.
Maximum temperatures are 95°C for cotton, 60°C for
synthetic fabrics, 40°C for delicate fabrics, wool and
fabrics to be hand-washed (WOOLEN/HAND WASH
programme).
for silk.
8
Downloaded From WashingMachine-Manual.com Manuals
2
/
6
3
MAX
4
/
15
Your new washing machine
This new washing machine incorporates all the latest functions and wash technology from Europe and is built
according to the highest manufacturing and quality standards, thus giving you optimal wash performance, lowest
energy & water consumption and specially designed fabric care options:
7
10
SANITARY WASH 95 a special wash cycle that heats up water to high temperature and maintains it for more
than 10 minutes will destroy most of all bacteria, thus ensuring healthy wash for you and your family.
ANTI-ALLERGY RINSE option is designed for people with sensitive skin and/or allergic problems. Additional
rinse phases and increased water level will ensure all residuals are rinsed away.
Water and electricity consumption automatically adapt to the wash load and type of garment, optimizing the
running cost for your washing machine.
LOW NOISE is ensured by our stable and high quality structure. 99% INSULATION are used in order to ensure
we have lowest possible level of noise leakage into you home environment.
SUPER QUICK WASH if you are in a hurry. Down to 23min option is available if you choose to wash with cold
water.
MAGIC BALL ensures lowest water, energy and detergent usage, saving your money and the environment.
POWERFUL SPIN (1000 and 1200 RPM) for dryer clothes and shorter drying time after your washing.
SUPERDAMPERS and ACTIVE BALANCE CONTROL controlled by the microprocessor of the washing machines ensure lowest possible vibrations and noise.
Our special fabric care program for WOOL, HANDWASH, SILK and DELICATES developed by our fabric care
specialists in Italy treats your delicate clothes with extreme care.
Description of the appliance
11
8
1. Detergent dispenser drawer
2. Control panel
3. Door locked pilot light
4. Door opening handle
5. Drain pump
6. Adjustable feet
Door locked pilot light
It stays on during the whole programme indicating
that the door is locked.
When the light goes out, the door can be opened
9
3
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
16
Downloaded From WashingMachine-Manual.com Manuals
7
When connect the waving junctures with inlet valve,
please aviod leakage and loose for joint deviation of
screw thread.
Pay attention to avoid the damage for over-bending.
Directly into a drain pipe at a height of not less
than 60cm and not more than 90cm.The end of the
drain hose must be always ventilated and the inside
diameter of the drainpipe must be larger than the
outside diameter of the drain hose. The drain hose
must not be kinked.
14
0
/
0
/
12
0
/
/
0
/
13
The inlet hose must not be lengthened. If it is too
short and you do not wish to move the tap, you will
have to purchase a new, longer hose specially designed for this type of use.
0
/
Electical connection
The machine is designed to operate on a 220V, single
phase, 50 Hz frequency supply.
Check that your domestic electrical installation can
take the maximum load required(2kW), also taking into
account any other appliance in use.
Connect the machine to an earthed socket.
Water drainage
The end of the drain hose can be positioned in three
ways:
Hooked over the edge of a sink using the plastic
hose guide supplied with the machine. In this case,
make sure the end cannot come unhooked when the
machine is emptying. This could be done by tying it
to the tap with a piece of string or attaching it to the
wall.
The manufacturer declines any responsibility
for damage or injury through failure to comply
with the above safety precaution.
Should the appliance power supply cable need
to be replaced, this should be carried out by
our Service Centre.
/
/
Please ensure that when the appliance is installed
the power supply cable is easily accessible
In a sink drain pipe branch. This branch must be
above the trap so that the bend is at least 60cm
above the ground.
6
Downloaded From WashingMachine-Manual.com Manuals
17
7. Plug the open holes with the plugs, which you will
find in the plastic envelope containing the instruction booklet.
Installation
Unpacking
All transit bolts and packing must be removed
before using the appliance.
60
95
You are advised to keep all transit devices so that they can be refitted if the machine ever has to betrantransported again.
1. Using a spanner, unscrew and remove the rear
right-hand bolt and lay the machine to its back,
taking care not to squash the hoses. This can be
avoided by placing one of the corner packing pieces
between the machines and the floor.
60
40
30
60
40
30
40
30
Positioning and levelling
Install the machine on a flat hard floor.
Make sure that air circulation around the machine is
not impeded by carpets,rugs etc. Check that the
machine does not touch the wall or other kitchen
units.
Carefully level by screwing the adjustable feet in or
out. Never place carboard, wood or similar materials
under the machine to compensate for any unevenness in the floor. Or the machine will make abnormal
noise or vibrate during spin.
2. Remove the polystyene block from the botton of
the machine and release the two plastic bags.
3. Carefully remove the right-hand bag then the left
bag by pulling them towards the centre of the
machine.
Water inlet
4.Put the bottom cover in the right position.
40
Put the juncture base A around the tap, fasten the
four screws and fix the inlet connector B, which
should ensure no water leakage.
To insert inlet tube in the sliding connector, press the
sliding knob C first, then put inlet tube in connector
B, and pull the tube to confirm if it is surely in
position.
30
5.Set the machine upright and remove the two remaining bolts from the back.
6.Pull out the three plastic spacers from the holes into
which the bolts were fitted.
18
Downloaded From WashingMachine-Manual.com Manuals
5
Disposal
Packaging materials
The materials marked with the symbol
clable.
PE
PS
PP
When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with the
remaining cable. Disable the door catch in order to
prevent children from becoming trapped .
are recy-
1
polyethylene
polystyrene
polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
4
Machine
Use authorised disposal sites for you old appliance.
Help to keep your country tidy!
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
With adequate pre-treatment, stains and limited soiling can be removed; the laundry can then be washed
at a lower temperature,so saving energy.
Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
The machine works more economically if it is fully
loaded.Do not overload!
2
3
Technical specifications
DIMENSION
Height
Width
Depth
85 cm
60 cm
49 cm
MAXIMUM LOAD
Cottons
Synthetics
Delicates
Wool / hand wash
Silk
5
2
2
1
1
SPIN SPEED
EWS1050
EWS1250
EWS1250Z
1000 rpm max.
1200 rpm max.
1200 rpm max.
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MAXIMUM FUSE PROTECTION
WATER PRESSURE
kg
kg
kg
kg
kg
AC 220V/50 Hz
2000 W
10 A
Minimum
Maximum
4
Downloaded From WashingMachine-Manual.com Manuals
50 kPa
800 kPa
19
Warnings
6
Installation
7
Always unplug the appliance and shut the water tap
after use.
All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not completely removed. Refer to the relevant paragraph in
the instruction book.
Any electrical work required to install the appliance
must be carried out by a qualified electrician.
Any plumbing work required to install this appliance
must be carried out by a qualified plumber.
After having installed the machine, check that it is
not standing on its electrical supply cables.
If the appliance is placed on a carpeted floor, ensure
that air can circulate freely between the feet and the
floor.
General safety
Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by inexperienced persons could cause serious danger. Contact
your local Service Centre.
Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
During high temperature wash programmes the door
glass may get hot. Do not touch it!
Before maintaining or repairing the machine, please
unplug the appliance.
Do not make it exposed to the sun for long time or
get wet in the rain.
Do not pour water directly on the washing machine.
The machine has run testing program with heating,
so may some condensing water left in tub.
The machine has self-protection function for power
supplier. When power supplier is abnormality, the
machine will not work or give alarm code (EBI). Please
turn off to avoid damaging your machine. Check
power supplier by qualified person. When you use
the machine again, make sure that power supplier
meets the requirement written in this instruction book.
Use
This appliance is designed for domestic use. It must
not be used for purposes other than those for which
it was designed.
Only wash fabrics which are designed to be machine
washed. Follow the instructions on each garment
label.
Do not overload the appliance. Follow the instruction
in the instruction book.
Make sure that all pockets are empty. Objects such
as coins, safety pins ,pins and screws can cause
extensive damage.
Do not wash garments saturated with petroleum,
methylated spirits, trichlorethylene, etc. If such
fluids have been used to remove stains prior to
washing, wait until they have completely evaporated from the fabric before placing garments in the
appliance.
Place small items such as socks , belts, etc . in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
Use only the recommended quantities of fabric
softener, an excessive amount could damage the
laundry.
Leave the porthole door slightly ajar when the appliance is not in use. This preserves the door seal and
prevents the formation of musty smells.
Always check that water has emptied out before
opening the door. If not, drain the water following the
instructions in the instruction book.
5
20
Downloaded From WashingMachine-Manual.com Manuals
Child safety
Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
The packaging components(e.g. Plastic film,
polystyrene) can be dangerous to children-danger of
suffocation! Keep them out of children’s reach.
Keep all detergents in a safe place out of children’s
reach.
Make sure that children or pets do not climb into the
drum.To avoid this the machine incorporates a speicial
feature. To activate this device, rotate the button
(without pressing it) inside the door clockwise until
the groove is horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise
until the groove is vertical.
3
Contents
Warnings
3
Disposal
4
Tips for environmental protection
Technical specifications
Installation
4
5
5
Positioning and levelling
5
Water inlet
5
Water drainage
6
Electrical connection
6
Your new washing machine
Description of the appliance
7
Detergent dispenser drawer
7
Control panel
Control panel description
Washing hints
19
Bodywork
19
Detergent dispenser drawer
19
Drain pump
19
Water inlet filter
19
Emergency emptying out
20
Frost precautions
20
Something not working?
- E10
- E20
- E40
E40
21-22
E10
E10
E10
E40
E20
E20
8
8
12
12
Temperatures for washing
12
Checking laundry
12
Maximum loads
12
Laundry weight
12
Removing stains before washing
12
Detergents and additives
13
Quantity of detergent to be used
13
Operating sequence
19
8
Sorting the laundry
International wash code symbols
Maintenance
7
7
Door locked pilot light
Use
18
Door seal
4
Unpacking
Programme table
14
15-17
2
Downloaded From WashingMachine-Manual.com Manuals
21
Dear customer,
Please read these operating instructions carefully and
pay particular attention to the safety notes indicated
in the first pages. We recommend that you keep this
instruction booklet for future reference and pass it on
to any future owners.
Transport damages
When unpacking the appliance, Check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and / or the key words (Warning! , Caution! ) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
22
Downloaded From WashingMachine-Manual.com Manuals
1
Downloaded From WashingMachine-Manual.com Manuals