Chauvet | TriShot LED | User manual | Chauvet TriShot LED User manual

User Manual
TABLE OF CONTENTS
1. Before you Begin ............................................................................. 3 What is Included............................................................................................ 3 Unpacking Instructions .................................................................................. 3 Text Conventions .......................................................................................... 3 Icons .............................................................................................................. 3 Safety Notes .................................................................................................. 4 2. Introduction ...................................................................................... 5 Product Overview .......................................................................................... 5 Product Dimensions ...................................................................................... 6 3. Setup ................................................................................................. 7 AC Power ...................................................................................................... 7 Mounting ....................................................................................................... 8 4. Operation .......................................................................................... 9 Configuration (DMX) ..................................................................................... 9 Configuration (Standalone Modes) ............................................................... 9 DMX Channel Assignments and Values ..................................................... 11 5. Technical Information.................................................................... 12 General Maintenance .................................................................................. 12 General Troubleshooting ............................................................................ 13 Returns Procedure ...................................................................................... 14 Claims ......................................................................................................... 14 Contact Information ..................................................................................... 14 DMX Primer ................................................................................................. 15 6. Technical Specifications ............................................................... 18 Document Information
The information and specifications contained in this document are subject to change without
notice. CHAUVET® assumes no responsibility or liability for any errors or omissions that may
appear in this manual.
© Copyright 2011 CHAUVET®. All rights reserved
Printed in P.R.C.
Electronically published by CHAUVET® in the United States of America
Page 2 of 18
Author
Editor
Manager
PD Manager
A. Chiappone
R. Jones
A. Reiss
F. Sellers
TriShot™ LED User Manual (Rev. 01a)
1. BEFORE YOU BEGIN
What is Included



1 x TriShot™ LED
1 x Warranty Card
1 x User Manual
Unpacking Instructions
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above
and that they are all in good condition. If the material inside the container (this product
and any other accessory included with it) appears damaged from shipping, or if the
container shows signs of mishandling, notify the shipper immediately. In addition,
retain the container and all the packing material for inspection.
See the Claims section in the “Technical Information” chapter.
Text Conventions
Convention
[10]
<Menu>
1~512
50/60
Settings
Menu > Settings
Meaning
A DIP switch to be configured
A key to be pressed on the fixture’s control panel
A range of values
A set of values of which only one can be chosen
A menu option not to be modified (for example, showing the operating
mode/current status)
A sequence of menu options to be followed
ON
A value to be entered or selected
Icon
Meaning
Icons
This paragraph contains critical installation, configuration, or operation
information. Failure to comply with this information may render the
fixture partially or completely inoperative, cause damage to the fixture,
or cause harm to the user.
This paragraph contains important installation or configuration
information. Failure to comply with this information may prevent the
fixture from functioning correctly.
This paragraph reminds you of useful, although not critical, information.
Product at a Glance
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Master/Slave
TriShot™ LED User Manual (Rev. 01a)





Auto Programs
Auto-ranging Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle





Page 3 of 18
Safety Notes
Please read the following notes carefully because they include important safety
information about the installation, usage, and maintenance of this product.
Page 4 of 18

Keep this User Manual for future consultation. If you sell this product to another
user, be sure that they also receive this document.

Always make sure that the voltage of the outlet to which you are connecting this
product is within the range stated on the decal or rear panel of the fixture.

This product is for indoor use only! To prevent risk of fire or shock, do not expose
this fixture to rain or moisture.

Make sure there are no flammable materials close to the unit while operating.

Always install this product in a location with adequate ventilation, at least 20 in (50
cm) from adjacent surfaces.

Be sure that no ventilation slots on the unit’s housing are blocked.

Always disconnect this product from the power source before cleaning it or
replacing the fuse.

Make sure to replace the fuse with another of the same type and rating.

If mounting this product overhead, always secure it to a fastening device using a
safety cable.

The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this
product at higher temperatures.

In the event of a serious operating problem, stop using the unit immediately.

Never try to repair this product. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical
assistance center.

Never connect this product to a dimmer pack.

Make sure the power cord is not crimped or damaged.

Never disconnect the power cord by pulling or tugging on the cord.

Never carry a fixture from the power cord or any moving part. Always use the
hanging/mounting bracket or the handles.

Always avoid direct eye exposure to the light source when this fixture is on.
TriShot™ LED User Manual (Rev. 01a)
2. INTRODUCTION
Product Overview
.
Focus adjustment
DMX out
DIP switches
Microphone
Sensitivity
Bracket adjustment
knob
Safety
Fuseholder
DMX in
Power in
(hardwired)
TriShot™ LED User Manual (Rev. 01a)
Page 5 of 18
Product Dimensions
Page 6 of 18
TriShot™ LED User Manual (Rev. 01a)
3. SETUP
AC Power
This product has an auto-ranging power supply and it can work with an input voltage
range of 100~240 VAC, 50/60 Hz.
To determine the power requirements for a particular fixture, see the label affixed to
the back plate of the fixture or refer to the fixture’s specifications chart. A fixture’s
listed current rating indicates its average current draw under normal conditions.
Always connect this product to a protected circuit (circuit breaker or fuse),
making sure that it has an appropriate electrical ground to avoid the risk of
electrocution or fire.
Never connect this product to a rheostat (variable resistor) or dimmer circuit,
even if the rheostat or dimmer channel serves only as a 0 to 100% switch.
TriShot™ LED User Manual (Rev. 01a)
Page 7 of 18
Mounting
Orientation
The TriShot™ LED may be mounted in any position, provided there is adequate room
for ventilation around it.
Rigging
Be sure that the structure onto which you are mounting this product can support its
weight. Please see the “Technical Specifications” section of this manual for weight
information.
Make sure to mount the fixture securely to a rigging point, whether an elevated
platform or a truss.
When rigging this product onto a truss, you should use a mounting clamp of
appropriate weight capacity. The bracket has a 13 mm hole, which is appropriate for
this purpose.
When mounting this product overhead, always use a safety cable.
Before deciding on a location for this product, always make sure that it will be easy to
access the unit for maintenance and programming purposes.
The bracket knobs allow for directional adjustment when aiming the fixture to the
desired angle. Only loosen or tighten the bracket knobs using your bare hands. Using
tools could damage the knobs.
Hanging bracket
Mounting Diagram Bracket knob
Page 8 of 18
TriShot™ LED User Manual (Rev. 01a)
4. OPERATION
Configuration (DMX)
Set this product in DMX mode to control it with a DMX controller.
1) Connect this product to a suitable power outlet.
2) Turn this product on.
3) Connect a DMX cable from the DMX output of the DMX controller to the DMX
input socket of this product.
Starting Address
When selecting a starting DMX address, always consider the number of DMX
channels the selected DMX mode uses. If you choose a starting address that is too
high, you could restrict the access to some of the fixture’s channels.
The TriShot™ LED uses seven DMX channels, which defines the highest
configurable address to 506.
If you are not familiar with the DMX protocol, you may refer to the “DMX Primer”
section in the “Technical Information” chapter.
To select the starting address, do the following:
1) Set DIP switch [10] to the OFF position.
2) Use DIP switch [1~9] to set the DMX starting address.
Configuration (Standalone Modes)
Set this product in one of the standalone modes to control it without a DMX controller.
1) Connect this product to a suitable power outlet.
2) Turn this product on.
Sound Active Mode
To enable the Sound Active mode, do the following:
1) Set DIP switch [10] to the ON position.
2) Turn the music on and adjust the microphone sensitivity knob until the fixture
starts reacting to the beat of the music.
The fixture will only respond to the low frequencies of the music (bass and
drums).
Automatic Mode
Never connect a fixture that is operating in any standalone mode, whether
Static, Automatic, or Sound to a DMX string connected to a DMX controller.
This is because fixtures in standalone mode may transmit DMX signals that
could interfere with the DMX signals from the controller.
To enable the Automatic Mode, follow the instructions below:
1) Set DIP switch [7, 9, 10] to the ON position.
2) Use DIP switch [1~6] to increase the operating speed.
You may combine DIP switch [1~6] to reach higher speeds. The higher the
number of the DIP switch, the more it will increase the operating speed.
TriShot™ LED User Manual (Rev. 01a)
Page 9 of 18
Static Colors
To enable the Static Colors mode, do the following:
1) Set DIP switch [8, 9, 10] to the ON position.
2) Use DIP switch [1~6] to set the color. See the chart below to see what color each
DIP switch controls.
Red
[1, 2]
Green
[3, 4]
Blue
[5, 6]
You may combine DIP switch for same color to increase the intensity.
Master/Slave Mode
This mode allows a single TriShot™ LED unit (the “master”) to control the actions of
one or more TriShot™ LED units (the “slaves”) without the need of a DMX controller.
The master unit will be set to operate in either Automatic or Sound Active mode, while
the slave units will be set to operate in Slave Mode. Once set and connected, the
slave units will operate in unison with the master unit.
Configure the units as indicated below.
Slave units:
1) Set DIP switch [2~10] to the OFF position.
2) Set DIP switch [1] to the ON position.
3) Connect the DMX input of the first slave unit to the DMX output of the master unit.
4) Connect the DMX input of the subsequent slave units to the DMX output of the
previous slave unit.
5) Finish setting and connecting all the slave units.
Master unit:
1) Set the master unit to operate in either Automatic or Sound mode, as previously
indicated.
2) Make the master unit the first unit in the DMX daisy chain.
Page 10 of 18

Configure all the slave units before connecting the master unit to the DMX
daisy chain.

Never connect a DMX controller to a DMX string configured for Master/Slave
operation because it may interfere with the signals from the master unit.

Do not connect more than 31 slave units to the master unit.
TriShot™ LED User Manual (Rev. 01a)
DMX Channel Assignments and Values
7-CH
Channel
Function
1
2
3
Red
Green
Blue
4
Color Macros
5
Speed
(CH.6 between
032~223)
Strobe
(channels 1~4 only)
Value
000  255
000  255
000  255
000  009
010  255
Dimmer (0~100%)
Dimmer (0~100%)
Dimmer (0~100%)
No function
Strobe (slow~fast)
000  255
Slow~fast
000  015
016  255
No function
Slow~fast (6~18 Hz)
RGB mode
Pulse effect 0%~100% (using RGB faders)
Pulse effect 100%~0% (using RGB faders)
Pulse effect 100%~0%~100% (using RGB
faders)
Auto fade transition
Auto snap transition (3 colors)
Auto snap transition (7 colors)
Sound triggering mode
Intensity (RGB/Macro modes): 0%~100%
6
Operating mode
(when CH.6 is set
between 032~223,
CH.5 controls the
speed)
000  031
032  063
064  095
096  127
128  159
160  191
192  223
224  255
7
Dimmer
000  255
TriShot™ LED User Manual (Rev. 01a)
Setting
Page 11 of 18
5. TECHNICAL INFORMATION
General Maintenance
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life. To maintain optimum performance and
minimize wear, you should clean your lighting fixtures at least twice a month.
However, be aware that usage and environmental conditions could be contributing
factors to increase the cleaning frequency.
To clean this fixture, follow the instructions below:

Unplug the fixture from power.

Wait until the fixture is cold.

Use a vacuum (or dry compressed air) and a soft brush to remove dust collected
on the external surface/vents.

Clean all external optics and glass surfaces with a mild soap solution, ammoniafree glass cleaner, or isopropyl alcohol.

Apply the solution directly to a soft, lint free cotton cloth or a lens cleaning tissue.

Softly drag any dirt or grime to the outside of the glass surface.

Gently polish the external glass surfaces until they are free of haze and lint.
Always dry the external glass surfaces carefully after cleaning them.
Page 12 of 18
TriShot™ LED User Manual (Rev. 01a)
General Troubleshooting
Symptom
Circuit breaker
or fuse keeps
blowing
Product does
not power up
Possible Cause
Possible Action

Excessive load on the circuit

Make sure that the total load
does not exceed 80% of the
breaker or fuse nominal
current

Short circuit along the
power lines

Check the power lines and
power cords

No energy on power outlet


Check power outlet
Change to another outlet

Loose or damaged power
cord

Check the power cord

Blown fuse

Replace blown fuse with a
good one of the same type
and rating

Internal problem

Send product for repair

Wrong starting address on
the fixture

Set the correct starting
address on the fixture
Use the right fader(s) on the
controller


Fixture does
not respond to
DMX
Wrong DMX personality on
the fixture


Set the correct DMX
fixture’s personality
Assign the faders
accordingly

Wrong polarity setting on
the DMX controller

Change the signal polarity
on the controller

Loose or damaged DMX
cable

Check the DMX cable
before the faulty unit

Internal problem

Send product for repair

Signal cables are not DMX
compatible

Replace non DMX cables
with true DMX cables

Interference with AC or
radio signals

Keep DMX cables away
from AC wires or radio
equipment

DMX cable too long

Install an optically coupled
DMX amplifier right before
the fixture with intermittent
problems

Too many fixtures
connected

Install an optically coupled
DMX amplifier after unit #32

Terminator not connected

Install a terminator, as
indicated in the “DMX
Primer” section.
Intermittent
DMX Problems
If you still experience problems after trying the above solutions, contact
CHAUVET® Technical Support.
TriShot™ LED User Manual (Rev. 01a)
Page 13 of 18
Returns Procedure
The user must send the merchandise prepaid, in the original box, and with its original
packing and accessories. CHAUVET® will not issue call tags.
Call CHAUVET® and request a Return Merchandise Authorization Number (RMA #)
before shipping the fixture. Be prepared to provide the model number, serial number,
and a brief description of the cause for the return.
The user must clearly label the package with a Return Merchandise Authorization
Number (RMA #). CHAUVET® will refuse any product returned without an RMA #.
DO NOT write the RMA # directly on the box. Instead, write it on a properly
affixed label.
Once you have received the RMA #, please include the following information on a
piece of paper inside the box:

Your name

Your address

Your phone number

The RMA #

A brief description of the problem
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. As a suggestion, proper UPS packing
or double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace
returned product(s).
Claims
The carrier is responsible for any damage incurred during shipping to this product or
any part that shipped with it. Therefore, if the received merchandise appears to have
damages caused during shipping, the customer must submit the damage report and
any related claims with the carrier, not CHAUVET®. The customer must submit the
report upon reception of the damaged merchandise. Failure to do so in a timely
manner may invalidate the customer’s claim with the carrier.
For other issues such as missing components or parts, damage not related to
shipping, or concealed damage, the customer must make claims to CHAUVET®
within seven (7) days of receiving the merchandise.
Contact Information
World Headquarters
United Kingdom & Ireland
CHAUVET®
CHAUVET® Europe Ltd.
General Information
Address:
Voice:
Fax:
Toll free:
General Information
5200 NW 108th Avenue
Sunrise, FL 33351
(954) 929-1115
(954) 929-5560
(800) 762-1084
Technical Support
Voice:
Fax:
(954) 929-1115 (Press 4)
(954) 756-8015
World Wide Web
Voice:
Fax:
Email:
Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
+44 (0)1773 511115
+44 (0)1773 511110
uktech@chauvetlighting.com
World Wide Web
www.chauvetlighting.com
Page 14 of 18
Address:
www.chauvetlighting.co.uk
TriShot™ LED User Manual (Rev. 01a)
DMX Primer
The USITT DMX512-A data transmission protocol (DMX, from now on) is based on
the EIA-485 standard and it has 512 channels (001 to 512). This system requires a
controller (DMX controller), one or more DMX compatible fixtures, and a DMX circuit
(also known as “DMX universe”) to link the fixtures to the controller.
Depending on their complexity and features, DMX compatible fixtures may require
from one to more than 30 DMX channels to operate. Some DMX fixtures have
multiple operation modes (also known as “personalities”), each with its own number
of channels and controllable parameters.
Starting Address
In the DMX system, the controller sends DMX data to each fixture based on the
fixture’s starting address. The starting address is the number of the DMX channel
(001 to 512) assigned to the fixture’s first control channel (Channel 1). When
assigning starting addresses to multiple fixtures, it is critical to ensure that no starting
address is already in use by another fixture to prevent channels from overlapping.
Otherwise, the affected fixtures may operate erratically.
For instance, a user has two DMX compatible fixtures. Fixture “A” has four channels
and fixture “B” has six channels. If the user configures the starting address of fixture
“A” to “001”, channels 001 through 004 on the DMX controller will control fixture “A”.
This means that the user should assign the starting address of fixture “B” to “005” or
higher. For a starting address of “005”, the DMX controller would use channels 005 to
010 to control fixture “B”.
It is possible to control multiple fixtures of the same type by assigning each one of
them the same starting address. In this case, all the fixtures would respond in unison
(synchronized) to the signals from the DMX controller.
Fixture Linking (Daisy Chain)
DMX compatible fixtures receive the control signals
from the DMX controller through the DMX cables.
Each fixture has a DMX In and a DMX Out
connector. The figure to the right illustrates how the
fixtures link to each other using multiple segments of
DMX cable in a sequential format called “daisy
chain”.
The order in which the fixtures connect to the DMX
controller is irrelevant because all fixtures receive
the same DMX signals and they only respond to
them based on their individual starting addresses.
However, it is important to notice that the
connections between fixtures should always be as
short and direct as possible.
To ensure the integrity of the DMX signal, follow the
recommendations of the EIA-485 standard:


DMX Controller
1st DMX Fixture
2nd DMX Fixture
To other fixtures
The maximum recommended cable length is 500 m (1,640 feet).
The maximum recommended number of fixtures on the same daisy chain is 32.
Connecting more than 32 fixtures on one daisy chain without the use of a DMX
optically-isolated splitter may result in deterioration of the digital DMX signal.
TriShot™ LED User Manual (Rev. 01a)
Page 15 of 18
DMX Cabling
The DMX protocol requires using special data cables to accommodate for the high
speed digital signals it uses. Despite their apparent similarities, data cables are
electrically different from standard microphone cables because they can carry high
frequency digital signals and have better protection against electromagnetic
interference. You can purchase CHAUVET® certified DMX cables directly from a
dealer/distributor or make your own DMX cable.
If you choose to make your own DMX cable, you must use a data-grade cable such
as the Belden 9841, which has the following electrical characteristics:
Type:
Maximum capacitance between conductors:
Maximum capacitance between conductor and shield:
Maximum resistance:
Nominal impedance:
shielded, 2-conductor twisted pair
30 pF/ft
55 pF/ft
20 ohms/1000 ft
100~140 ohms
DMX Connectors Each DMX cable must have a male XLR connector on one end and a female XLR
connector on the other end. The DMX protocol indicates that the XLR connectors
must have five pins. However, most lighting fixtures use the 3-pin XLR connector.
The pin assignment of the 3-pin and 5-pin XLR connectors in a DMX cable is as
follows:
Female Plug
Male Plug
Signal
3-Pin
5-Pin
5-Pin
3-Pin
Signal
Common
1
1
1
1
Common
Data -
2
2
2
2
Data -
Data +
3
3
3
3
Data +
Not used
4
4
Not used
Not used
5
5
Not used
You can use the above table to create a 3-pin/3-pin cable, a 5-pin/5-pin cable, or a 3pin to 5-pin adapter.
The DMX daisy chain uses a terminator to reduce signal transmission problems,
especially with long cables. The terminator consists of either a 3-pin or 5-pin XLR
male plug with a 120 Ω, ¼ W resistor connected to the wire side of pins 2 and 3, as
shown below.
The terminator plug connects to the DMX Out socket of the last DMX fixture in the
daisy chain.
Do not allow the common wire of the DMX cable to touch the fixture’s chassis
ground. This could cause a ground loop, which may affect your fixtures’
performance. Test all DMX cables with an ohmmeter to verify the correct
polarity of the wires, and to make sure that they are not touching the shield or
each other.
Page 16 of 18
TriShot™ LED User Manual (Rev. 01a)
DIP Switch Reference Guide
You can use the table below to set your fixture’s DIP switches. Imagine that you want
to find the DIP switch settings for DMX address 328:
1) Find 328 among the addresses from the table and point at it with your finger.
2) Move your finger to the left and you will find the settings for DIP Switches 1 to 5.
DIP Switches 1, 2, 3, and 5 are Off (0), while DIP Switch 4 is On (1).
3) Go back and point at the 328 address.
4) Move your finger upward and you will find the settings for DIP Switches 6 to 9.
DIP Switches 6 and 8 are Off (0), while DIP Switches 7 and 9 are On (1).
5) See below how the DIP Switches will look after configuring them.
#9
#8
#7
#6
#1 #2 #3 #4 #5
DIP Switches
0 = Off
1=Off
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
TriShot™ LED User Manual (Rev. 01a)
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
DMX Address
----1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
Page 17 of 18
6. TECHNICAL SPECIFICATIONS
Dimensions and Weight
Length
Width
Height
Weight
8.6 in (218 mm)
5.2 in (131 mm)
6.7 in (171 mm)
2.6 lbs (1.2 kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power
Power Supply Type
Range
Voltage Selection
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
120 V, 60 Hz
230 V, 50 Hz
Consumption
17 W (0.15 A)
20 W (0.09 A)
Output
Power I/O
Input
Connectors
IEC
N/A
Cord plug
Edison
N/A
Type
Power
Lifespan
LED
3W
50,000 hours
Color
Quantity
Current
Tri-color
1
350 mA
Light Source
Photo Optic
Parameter
Illuminance @ 1 m
1,592 lx
Illuminance @ 2 m
305 lx
Beam angle
11º
Maximum External Temp.
Cooling System
104° F (40° C)
Convection
I/O Connectors
Connector Type
Channel Range
3-pin XLR
Sockets
7
Thermal
DMX
Ordering
TriShot™ LED
TRISHOTLED
Page 18 of 18
TriShot™ LED User Manual (Rev. 01a)
Download PDF

advertising