Signamax 12-Channel Rack Mount Converters User`s manual
SignaMax F0-065-1200 Series is a 12-port media converter that can house up to twelve media converters in a 1U standard 19” rackmountable size. The front panel provides status LEDs and an uplink push button for each 10/100BaseTX to 100BaseFX media converter or status LEDs and a dip switch array for each 1000BaseT to 1000BaseSX/LX media converter. The device supports full or half duplex mode on TX port, and has redundant power supplies. The allowed fiber media are multimode fiber using ST, SC, VF-45, or MT-RJ connector, and singlemode fiber using SC connector.
PDF
Download
Document
Advertisement
Advertisement
Signamax FO-065-1200 series 12-Port Media Converter Signamax Connectivity Systems FO-065-1200 Series 12-Port Media Converter U S User’s Manual E R ’ S G U I D E 1 Signamax Connectivity Systems 12-Port Media Converter F0-065-1200 Series User’s Guide Signamax FO-065-1200 series 12-Port Media Converter Preface This manual describes how to install and use the Signamax FO065-1200 series 12-Port Media Converter. The system introduced here is capable of housing up to twelve media converters, each of which offers a single channel media conversion solution: 10/100BaseTX ↔ 100BaseFX 1000BaseT ↔ 1000BaseSX/LX In this manual, you will find: • • • • • An introduction to the system Product features Illustrative LED functions Installation instructions Specifications User’s Manual 1 Signamax FO-065-1200 series 12-Port Media Converter Table of Contents PREFACE 1 TABLE OF CONTENTS 2 PRODUCT OVERVIEW 3 SIGNAMAX FO-065-1200 SERIES 12-PORT MEDIA CONVERTER PACKAGE CONTENTS PRODUCT FEATURES FRONT PANEL DISPLAY Front Panel Understanding LEDs 3 3 4 5 5 6 INSTALLATION 8 SELECTING A SITE FOR THE EQUIPMENT CONNECTING TO POWER 8 9 SPECIFICATIONS 10 ORDERING INFORMATION 11 CONTACT INFORMATION 12 2 User’s Manual Signamax FO-065-1200 series 12-Port Media Converter Product Overview Signamax FO-065-1200 series 12-Port Media Converter The Signamax FO-065-1200 series 12-Port Media Converter can house up to twelve media converters in a 1U standard 19” rackmountable size. The front panel of the Signamax FO-0651200 12-Port Media Converter provides status LEDs and an uplink push button for each 10/100BaseTX to 100BaseFX media converter or status LEDs and a dip switch array for each 1000BaseT to 1000BaseSX/LX media converter. Figure 1: Signamax FO-065-1200 12-Port Media Converter Package Contents When you unpack the product’s package, you should find the items listed below: Signamax FO-065-1200 series 12-Port Media Converter Two AC power cords User’s manual Rackmount ears with screws Please inspect the contents, and report any apparent damage or missing items immediately to your authorized reseller. User’s Manual 3 Signamax FO-065-1200 series 12-Port Media Converter Product Features ♦ ♦ ♦ ♦ ♦ ♦ ♦ 4 Houses twelve channels of media conversion Front panel status LEDs Standard 19” rackmountable size, 1U high 2 Redundant Power Supplies 10/100BaseTX to 100BaseFX converters: Fiber media allowed: multimode fiber using ST, SC, VF-45, or MT-RJ connector, singlemode fiber using SC connector One push button for uplink (MDI/MDI-X) crossover configuration 1000BaseT to 1000BaseSX/LX converters: Fiber media allowed: multimode fiber using SC connector or singlemode fiber using SC connector Support Auto-MDIX on TX port One dip switch for setting auto detecting duplex mode or full duplex One dip switch for setting link pass-through: TX port disconnected when SX/LX port is disconnected, SX/LX port still connected when TX port is disconnected Support full or half duplex mode on TX port User’s Manual Signamax FO-065-1200 series 12-Port Media Converter Front Panel Display FRONT PANEL The front panel of this Signamax FO-065-1200 12-Port Media Converter shows the layout of the twelve media converter channels. There are 12 sets of LED indicators, which provide you with instant feedback on the status of each media converter channel. Figure 2: Front Panel of the Signamax FO-065-1200 series 12-Port Media Converter User’s Manual 5 Signamax FO-065-1200 series 12-Port Media Converter UNDERSTANDING LEDS 10/100TX to 100FX Media Converter LEDs State Indication PWR Steady Power on Off Power off LNK/ACT Steady A valid network connection established LNK stands for LINK Flashing Transmitting & receiving ACT stands for activity 100 Steady TX port connection at speed of 100Mbps Off TX port connection at speed of 10Mbps FDX/COL Steady Connection in full duplex mode FDX stands for FULL-DUPLEX Flashing Off 6 Collision occurred COL stands for collision Connection in half-duplex mode User’s Manual Signamax FO-065-1200 series 12-Port Media Converter 1000T to 1000SX/LX Media Converter LEDs State Indication Power LNKC LNKF Steady Power feeding in Off No power Steady TX port: A valid network connection established. LNKC stands for LINK/Copper Off No connection Steady FX port: A valid network connection established. LNKF stands for LINK/Fiber Off No connection FDX/COL Steady Connection in full duplex mode FDX stands for FULL DUPLEX Flashing Collision occurred COL stands for COLLISION RX TX Off Connection in half duplex mode Steady Receiving data Off No reception Steady Transmitting data Off No transmission User’s Manual 7 Signamax FO-065-1200 series 12-Port Media Converter Installation Selecting a Site for the Equipment As with any electric device, you should place the equipment where it will not be subjected to extreme temperatures, humidity, or electromagnetic interference. Specifically, the site you select should meet the following requirements: - The ambient temperature should be between 32 and 104 degrees Fahrenheit (0 to 40 degrees Celsius). - The relative humidity should be less than 90 percent, non-condensing. - Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for IEC 801-3, Level 2 (3V/M) field strength. - Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes on each side of the switch or the fan exhaust port on the side or rear of the equipment. - The power outlet should be within 6 feet (1.8 meters) of the switch. 8 User’s Manual Signamax FO-065-1200 series 12-Port Media Converter Connecting to Power Step 1: Connect the supplied AC power cords to the receptacles on the rear panel of the system. Step 2: Attach the plugs from each of the dual power supplies into standard AC outlets with a voltage range from 100~240V AC. Step 3: Turn on the system by flipping the ON/OFF switches beside the dual power supplies’ receptacles to the ON position. Step 4: The power LED of each media converter will shine after turning on the system. Step 5: The link LED of each media converter will shine after connecting twisted pair copper cabling between the TX port (or fiber optic cabling between the FX port) and another working networked device.** Figure 3: Rear view of the Signamax FO-065-1200 12-Port Media Converter ** PLEASE NOTE: The primary function of the Signamax 065-1200 series 12-channel media converters is to convert existing twisted-pair network switch or hub ports in a network to fiber optic connectivity for distance extension or immunity to electro-magnetic or radio frequency interference (EMI/RFI). These devices do not contain a network switching matrix; rather, they “front-end” a network switch or hub to convert the twisted-pair connections to fiber optic capability. Each channel of media conversion in these devices has a one-to-one relationship with an available network switch port. Ports from the Signamax 065-1200 series 12-channel media converters can be routed to network switch ports located on different network switches. There is no requirement for the Signamax 1200 series’ converter channels to be routed to a single switch. When used in multiple switch configurations, twisted-pair ports from multiple Signamax 065-1200 series converters may be assigned and cabled to multiple network switches to avoid a single point of failure in redundant network configurations. User’s Manual 9 Signamax FO-065-1200 series 12-Port Media Converter Specifications Applicable Standards IEEE 802.3 10BaseT, IEEE 802.3u 100BaseTX/FX, IEEE 802.3ab 1000BaseT, IEEE 802.3z 1000BaseSX/LX Fixed Ports 12-Bay of 1 TX port and 1 FX port Speed – 10BaseT 10/20Mbps for half/full-duplex 100BaseTX/FX 100/200Mbps for half/full-duplex 1000BaseT/SX/LX 1000/2000Mbps for half/full-duplex Forwarding rate 14,880pps for 10Mbps 148,800pps for 100Mbps 1,488,000pps for 1000Mbps LED Indicators 10/100TX to 100FX: Per Bay- (1 LED): Power TX Port- (3 LEDs): LNK/ACT; FDX/COL; 100 FX Port- (2 LEDs): LNK/ACT; FDX/COL 1000T to 1000SX/LX: Per Bay- (4 LEDs): Power; TX; RX; FDX/COL TX Port- (1 LED): LNKC FX Port- (1 LED): LNKF Dimensions 440 × 243 × 45 mm Power 100 ~ 240 VAC, 50/60 Hz, 5.4A (x2) Power Consumption 65W (x2) Max. Operating Temperature 0°C ~ 40°C (32°F ~ 104°F) Storage Temperature -25°C ~ 70°C (-13°F ~ 158°F) Humidity 10 ~ 90%, non-condensing 10 User’s Manual Signamax FO-065-1200 series 12-Port Media Converter Ordering Information FO-065-1200ST00 10/100BaseT/TX to 100BaseFX 12-Port Media Converter – ST Multimode Connectors FO-065-1200SC10 10/100BaseT/TX to 100BaseFX 12-Port Media Converter – SC Multimode Connectors FO-065-1200SC20 10/100BaseT/TX to 100BaseFX 12-Port Media Converter – SC Singlemode Connectors FO-065-1200MT72 10/100BaseT/TX to 100BaseFX 12-Port Media Converter – MT-RJ Multimode Connectors FO-065-1200LC74 10/100BaseT/TX to 100BaseFX 12-Port Media Converter – LC Multimode Connectors FO-065-1200SC95 1000BaseT to 1000BaseSX 12-Port Media Converter – SC Multimode Connectors FO-065-1200SC97 1000BaseT to 1000BaseLX 12-Port Media Converter – SC Singlemode Connectors User’s Manual 11 Signamax FO-065-1200 series 12-Port Media Converter Contact Information SIGNAMAX CONNECTIVITY SYSTEMS An AESP Company 16295 N.W. 13th Avenue Suite A Miami, Florida 33169, U.S.A. Phone: 305-944-7710 Fax: 305-949-4483 Sales: 800-446-2377 Tech. Support: 800-446-2377, ext. 201 Http://www.signamax.com E-mail: [email protected] 12 User’s Manual ">

Public link updated
The public link to your chat has been updated.
Advertisement