Barco | DCS-200 | Instruction manual | Barco DCS-200 Instruction manual

a`pJOMM
rëÉêÛë=dìáÇÉ
•
•
Manual #: 26-0604010-00
Revision: 00
a`pJOMM==√==rëÉêÛë=dìáÇÉ
`çéóêáÖÜí
© Barco. May 30, 2008
All rights reserved. No part of this document may be copied, reproduced or translated. It
shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior
written consent of Barco.
kçíáÅÉ
Barco provides this manual “as is” without warranty of any kind, either expressed or
implied, including but not limited to the implied warranties or merchantability and fitness for
a particular purpose. Barco may make improvements and/or changes to the product(s) and/
or the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are
periodically made to the information in this publication; these changes are incorporated in
new editions of this publication.
cÉÇÉê~ä=`çããìåáÅ~íáçåë=`çããáëëáçå=Ec``F=pí~íÉãÉåí
This equipment has been tested and found to comply with the limits for a class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area may cause harmful interference, in which case the user will be responsible for
correcting any interference.
dì~ê~åíÉÉ=~åÇ=`çãéÉåë~íáçå
Barco provides a guarantee relating to perfect manufacturing as part of the legally
stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all
delivered goods for damage incurred during transport, as well as for material and
manufacturing faults. Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special
systems and software on the date of commissioning, at latest 30 days after the transfer of
risks. In the event of justified notice of compliant, Barco can repair the fault or provide a
replacement at its own discretion within an appropriate period. If this measure proves to be
impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or
cancellation of the contract. All other claims, in particular those relating to compensation for
direct or indirect damage, and also damage attributed to the operation of software as well
as to other services provided by Barco, being a component of the system or independent
service, will be deemed invalid provided the damage is not proven to be attributed to the
absence of properties guaranteed in writing or due to the intent or gross negligence or part
of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by
Barco, or if the goods are handled incorrectly, in particular if the systems are commissioned
operated incorrectly or if, after the transfer of risks, the goods are subject to influences not
2
DCS-200 • User’s Guide
agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid.
Not included in the guarantee coverage are system failures which are attributed to
programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal
wear as well as normal maintenance are not subject to the guarantee provided by Barco
either.
The environmental conditions as well as the servicing and maintenance regulations
specified in this manual must be complied with by the customer.
qê~ÇÉã~êâë
Brand and product names mentioned in this manual may be trademarks, registered
trademarks or copyrights of their respective holders. All brand and product names
mentioned in this manual serve as comments or examples and are not to be understood as
advertising for the products or their manufactures.
`çãé~åó=^ÇÇêÉëë
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, California 95670
USA
•
•
•
•
Phone: (916) 859-2500
Toll Free: (888) 414-7226
Fax: (916) 859-2515
Website: www.barco.com
Barco N.V.
Noordlaan 5
8520 Kuurne
BELGIUM
•
•
•
Phone: +32 56.36.82.11
Fax: +32 56.35.16.51
Website: www.barco.com
Technical Support
•
DCS-200 • User’s Guide
Tech Line: (866) 374-7878 — 24 hours per day, 7 days per week
3
léÉê~íçêë=p~ÑÉíó=pìãã~êó
The general safety information in this summary is for operating personnel.
aç=kçí=oÉãçîÉ=`çîÉêë=çê=m~åÉäë
There are no user-serviceable parts within the unit. Removal of the top cover will expose
dangerous voltages. To avoid personal injury, do not remove the top cover. Do not operate
the unit without the cover installed.
mçïÉê=pçìêÅÉ
This product is intended to operate from a power source that will not apply more than 230
volts rms between the supply conductors or between both supply conductor and ground. A
protective ground connection by way of grounding conductor in the power cord is essential
for safe operation.
dêçìåÇáåÖ=íÜÉ=mêçÇìÅí
This product is grounded through the grounding conductor of the power cord. To avoid
electrical shock, plug the power cord into a properly wired receptacle before connecting to
the product input or output terminals. A protective-ground connection by way of the
grounding conductor in the power cord is essential for safe operation.
rëÉ=íÜÉ=mêçéÉê=mçïÉê=`çêÇ
Use only the power cord and connector specified for your product. Use only a power cord
that is in good condition. Refer cord and connector changes to qualified service personnel.
rëÉ=íÜÉ=mêçéÉê=cìëÉ
To avoid fire hazard, use only the fuse having identical type, voltage rating, and current
rating characteristics. Refer fuse replacement to qualified service personnel.
aç=kçí=léÉê~íÉ=áå=bñéäçëáîÉ=^íãçëéÜÉêÉë
To avoid explosion, do not operate this product in an explosive atmosphere.
4
DCS-200 • User’s Guide
bèìáéãÉåí=j~êâáåÖ=~åÇ=p~ÑÉíó=qÉêãë=
t^okfkd
Highlights an operating procedure, practice, condition, statement, etc., which, if not strictly
observed, could result in injury to or death of personnel.
Note
Highlights an essential operating procedure, condition or
statement.
`^rqflk
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
^sboqfppbjbkq>
Le point d´exclamation dans un triangle equilatéral signale à alerter l´utilisateur qu´il y a
des instructions d´operation et d´entretien tres importantes dans la litérature qui
accompagne l´appareil.
slopf`eq
Ein Ausrufungszeichen innerhalb eines gleichwinkeligen Dreiecks dient dazu, den
Benutzer auf wichtige Bedienungs-und Wartungsanweisungen in der Dem Great
beiliegenden Literatur aufmerksam zu machen.
DCS-200 • User’s Guide
5
`Ü~åÖÉ=eáëíçêó
The table below lists the changes to the DCS-200 User’s Guide.
Table 0-1. Change History
Rev
00
6
Date
May 30, 2008
ECP #
558656
Description
DCS-200 User’s Guide
Approved By
R. Pellicano
DCS-200 • User’s Guide
q~ÄäÉ=çÑ=`çåíÉåíë
`Ü~éíÉê=N
fåíêçÇìÅíáçå =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=NP
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to Use This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Navigating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents and Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the DCS-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A Word About HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connectivity Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
`Ü~éíÉê=O
e~êÇï~êÉ=lêáÉåí~íáçå =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=NV
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inputs Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Effects Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Take . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
`Ü~éíÉê=P
27
28
28
28
28
29
29
30
31
32
léÉê~íáçåK=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=PP
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Up Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Button States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 • User’s Guide
19
20
21
22
23
24
25
fåëí~ää~íáçå =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=OT
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unpacking and Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable and Adapter Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rack-Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Cord/Line Voltage Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Format Connection Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
`Ü~éíÉê=Q
13
13
14
14
14
14
15
15
15
17
18
18
33
34
34
35
7
Table of Contents
Quick Setup and Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Function Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Status Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trans Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Pattern. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sync Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gamma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Output Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preview Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Src . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Format (Preview) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Patterns (Preview) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preview Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save (Preview) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjust On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Colorspace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timing Adjust. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contrast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Input Configuration Files . . . . . . . . . . . . . . . . . . . . . . .
Reset Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Save Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Delete Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Recall Config . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGO Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Preference. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
In Auto Acquire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Input Config. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Input Save. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auto Take . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Black Auto Take . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Auto Take. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Menu Context . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VFD Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDID Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVI Cable Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
36
38
39
41
44
46
47
47
48
48
49
49
49
50
51
51
52
52
53
53
55
55
56
56
57
57
60
61
61
62
63
63
64
64
65
66
67
69
70
70
71
72
72
72
72
72
73
73
74
76
77
79
DCS-200 • User’s Guide
Table of Contents
File Association Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Save System State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Tech Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Using Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Input Selection Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Flip-flop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Understanding Auto Acquire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Using HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Using the LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Saving a Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Transitioning to a Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Deleting a Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Using Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Using Black. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Black Auto Take Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Black Auto Take On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Using Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Introduction to Keying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
Performing a Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Key Auto Take Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Key Auto Take On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Key Transition Combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Mix Key Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Mix Key Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Mix Source plus Key Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Mix Source plus Key Down . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Source Transition Under Key . . . . . . . . . . . . . . . . . . . . . . . . 99
Fade to Black from Source plus Key . . . . . . . . . . . . . . . . . . 100
Fade up from Black to Source plus Key . . . . . . . . . . . . . . . 100
Understanding Front-Panel Lockout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Full Lockout Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Executive Lockout Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
`Ü~éíÉê=R
drf=léÉê~íáçåë =K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNMP
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
GUI Connection and Launch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
GUI Operations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
`Ü~éíÉê=S
réÖê~ÇáåÖ=pçÑíï~êÉK=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNMT
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Upgrade Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Downloading Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Via FTP Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Via Web Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Upgrade Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 • User’s Guide
107
108
108
108
109
109
109
110
9
Table of Contents
Troubleshooting Ethernet Communication . . . . . . . . . . . . . . . . . . . . 113
^ééÉåÇáñ=^=
péÉÅáÑáÅ~íáçåëK=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNNR
In This Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Physical and Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communications Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Agency Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog 15-pin D Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DVI-I Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Format Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
^ééÉåÇáñ=_=
oÉãçíÉ=`çåíêçä=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNOT
In This Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Communicating with DCS-200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Protocol. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command Responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Query Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Codes: General Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Codes: No Error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 Command List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ethernet Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EMAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
GATEWAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SUBNET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOACQ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BACKGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLKVID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CBLEQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EDIDTYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FREEZE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IADJ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IAUTOC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IAVAIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICDEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
115
116
116
117
117
117
118
118
119
120
121
122
127
127
128
128
128
128
130
130
130
131
134
134
134
134
135
135
135
135
135
135
136
136
136
136
137
137
137
137
138
138
138
139
DCS-200 • User’s Guide
Table of Contents
ICNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICPHO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICREC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICSAV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ICSP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHATV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHCROP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHPAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHPOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHTOTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IHUE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRCNT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IRES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISLICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ITYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IVATV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IVCROP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IVPAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IVPOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IVTOTAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCOMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OAVAIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OCSAV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OGM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OSRC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OSYNC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OTPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OTPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOCFG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOSAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOTAKE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLKTRAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCLR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LDMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LFEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DCS-200 • User’s Guide
139
139
139
140
140
140
140
141
141
141
142
142
142
142
143
143
143
144
144
144
145
145
146
146
146
146
147
147
147
147
147
147
147
148
148
148
149
149
149
150
151
151
151
151
151
151
152
152
152
152
152
153
11
Table of Contents
LINT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOCKOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PREVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TRNTIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VFDBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Key Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LKEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGO Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGODEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGOSAVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGOSEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
^ééÉåÇáñ=`=
`çåí~Åí=fåÑçêã~íáçå=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNRV
In This Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Return Material Authorization (RMA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
fåÇÉñ
12
153
153
153
153
154
154
154
154
155
155
155
155
155
155
156
156
157
157
157
159
159
159
160
=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=K=KNSN
DCS-200 • User’s Guide
NK==fåíêçÇìÅíáçå
få=qÜáë=`Ü~éíÉê
This chapter is designed to introduce you to the DCS-200 User’s Guide. Areas to be
covered are:
•
•
•
•
•
•
Chapter Structure
How to Use This Guide
Conventions
About the DCS-200
Connectivity Diagram
Application Questions
`Ü~éíÉê=píêìÅíìêÉ
The following chapters provide instructions for all aspects of DCS-200 operations:
•
Chapter 1, “Introduction” provides a system overview, a list of features, and a
system connectivity diagram.
•
Chapter 2, “Hardware Orientation” on page 19 provides detailed diagrams of the
system’s front and rear panels.
•
Chapter 3, “Installation” on page 27 provides comprehensive system installation
instructions.
•
Chapter 4, “Operation” on page 33 provides a menu tree, plus comprehensive
system operating instructions.
•
Chapter 5, “GUI Operations” on page 103 provides launch and operating
instructions for the system’s web-based GUI.
•
Chapter 6, “Upgrading Software” on page 107 outlines procedures for upgrading
system software components.
•
•
Appendix A, “Specifications” on page 115 lists the DCS-200’s specifications.
•
DCS-200 • User’s Guide
Appendix B, “Remote Control” on page 127 provides information regarding
remote control protocol.
Appendix C, “Contact Information” on page 159 lists important Barco contact,
RMA, warranty and technical support details.
13
NK==fåíêçÇìÅíáçå
How to Use This Guide
eçï=íç=rëÉ=qÜáë=dìáÇÉ
This section provides important tips for streamlining your use of this User’s Guide in its
electronic “PDF” form.
k~îáÖ~íáåÖ
Use Acrobat Reader’s “bookmarks” to navigate to the desired location. All chapter files
have the same bookmark structure for instant navigation to any section. Please note:
•
•
Extensive hyperlinks are provided within the chapters.
•
Use the “Previous Page” and “Next Page” buttons to go to the previous or next
page within a file.
•
Use Acrobat’s extensive search capabilities, such as the “Find” tool and “Search
Index” tool to perform comprehensive searches as required.
Use Acrobat’s “Go to Previous View” and “Return to Next View” buttons to trace
your complete navigational path.
q~ÄäÉ=çÑ=`çåíÉåíë=~åÇ=fåÇÉñ
Use the Table of Contents bookmarks to navigate a desired topic. Click any item to
instantly jump to that section of the guide. You can also use the Index to jump to specific
topics within a chapter. Each page number in the Index is a hyperlink.
`çåîÉåíáçåë=
The following conventions are used throughout this guide:
•
•
•
The symbol „ denotes an operations procedure.
The symbol S denotes an example.
Entries written in bold-face capital letters denote physical buttons or chassis
connectors.
S Press LOGO to ...
•
The term “select” is used as an abbreviation for “scroll to a selected menu line
and press the SEL button.”
•
A sequence of menu steps is represented by the menu names, separated by
arrows (>).
S INPUT > Timing Adjust > H Position
... indicates the following sequence:
14
a.
From the Main Menu, select INPUT to display the Input Menu.
b.
Scroll to the Timing Adjust line and press SEL to display the Timing
Adjust Menu.
c.
Scroll to the H Position line and press SEL to adjust the image’s
horizontal position.
DCS-200 • User’s Guide
NK==fåíêçÇìÅíáçå
About the DCS-200
^Äçìí=íÜÉ=a`pJOMM
The following topics are discussed in this section:
•
•
•
Overview
Features
A Word About HDCP
lîÉêîáÉï
DCS-200 is a high-quality dual-channel presentation switcher designed to provide true
seamless switching between various input sources. The DCS-200 offers all the features of
the DCS-100, and adds a scaled Preview mode that supports sizing and adjusting input
layers before taking them to Program. High-quality image scaling is maintained
throughout.
DCS-200 offers straightforward and simple operating modes, and is ideal for use in live
events, company boardrooms, hotel ballrooms, houses of worship, and in education and
training facilities. As the ideal “simple” presentation switcher to learn and operate,
DCS-200 provides a full screen output only, with no PIP capability.
DCS-200 accepts analog, DVI, and HD-SDI input sources and converts them to a wide
variety of output formats. Output video is provided on analog and DVI connectors
simultaneously. DCS-200 also allows you to capture and store up to three images to be
used as full-screen logs during the presentation. Any DVI source can be used as a
luminance key, providing an easy way for users to create titles and lower-third graphics.
Please note:
•
To ensure trouble-free orientation, installation and operation of your DCS-200,
please follow all procedures in the following chapters:
~
~
~
•
Chapter 2, “Hardware Orientation” on page 19.
Chapter 3, “Installation” on page 27.
Chapter 4, “Operation” on page 33.
Should you have any questions regarding the installation or operation of the DCS200 system, please consult with the factory. Refer to Appendix C, “Contact
Information” on page 159 for contact details.
=
cÉ~íìêÉë
The major features of the DCS-200 system are:
•
The system supports input and output resolutions up to UXGA, including all HD
resolutions up to 1080p, eliminating the need to create custom output formats.
NTSC and PAL are supported as inputs only.
Note
•
The DCS-200 supports DVI, analog computer and video formats on the DVI-I
inputs.
~
DCS-200 • User’s Guide
Outputs cannot be interlaced.
HDCP protocol is supported, and the DCS-200 is considered an HDCP
repeater in this configuration. Incoming encrypted data is encrypted
15
NK==fåíêçÇìÅíáçå
About the DCS-200
going out, and all analog outputs, plus the freeze and LOGO store
functions are disabled when the DCS-200 processes HDCP content.
Refer to the “A Word About HDCP” section on page 17 for more details.
~
•
•
•
A Preview mode lets you view and adjust layers before moving them to Program.
The DCS-200 stores and recalls up to three full-screen logos.
The system provides true seamless switching between all inputs, including one of
the three stored full-screen logos.
•
An Auto Take feature (in the User Preference Menu) supports transitioning from
one input source to another without pressing TAKE.
•
The following scaling and de-interlacing features are provided:
~
~
~
~
•
10-bit scaling
10-bit 4:2:2 de-interlacer with diagonal filter
165MHz maximum pixel rate
Low video delay: Interlaced sources, 3 fields (max)
The DCS-200 provides the ability to luminance key unscaled DVI sources. Please
note:
~
Keys are set up from the Key Menu. The front panel KEY button is used
to enable or disable the key transition.
~
Key transitions are performed at the same rate as the full screen source
transitions.
~
If the key source resolution is greater than the output resolution, the
DCS-200 only displays an area equal to the output resolution. This area
is selectable using the menu.
~
If the key source resolution is less than the output resolution, the key is
centered on screen, and can be moved within the screen boundaries.
•
The DCS-200 provides the ability to “auto acquire” input sources. The system
monitors inputs at all times, and if a timing change occurs, the system
automatically reacquires and displays the source — once the timing has been
measured.
•
The DCS-200 offers simple and intuitive menus:
~
~
16
1080i RGB input is supported on the DVI digital input.
Presentations can be switched without accessing any setup menus.
Two front-panel lockout modes enable you to lock out menu access,
either completely or partially.
•
•
•
The DCS-200 provides an integrated test pattern generator.
•
The File Association feature provides the ability to save and recall up to 64 input
configuration files, and associate each of them with one or more inputs.
The DCS-200 offers an HD/SD SDI input as standard.
A built-in web-based GUI enables you to perform all setup and transition
functions, just like the front panel.
DCS-200 • User’s Guide
NK==fåíêçÇìÅíáçå
About the DCS-200
^=tçêÇ=^Äçìí=ea`m
HDCP stands for High-Bandwidth Digital Content Protection, an industry-wide copy
protection scheme that is used to prevent the potential interception of digital data between
the source (e.g., a Blu-Ray player) and the target display (e.g., an HDCP compliant display
or monitor). The HDCP format was designed by Intel®, and it uses an “authentication and
key exchange” procedure to accomplish the required protection. For proper
implementation, products that are compatible with the HDCP format require a secure
connection to a compliant display, such as a projector or monitor.
In applications in which a DCS-200 is used, when an HDCP compliant device is connected
to the DCS-200, an HDCP “session” is created. In this session (which is transparent to the
user), “keys” are exchanged between the source device (e.g., a Blu-Ray player) and the
HDCP compliant display.
The source device queries the display to ensure that the equipment is HDCP compliant
before video is shown. Non-HDCP equipment such as PCs will work with any DVI
compliant display, but HDCP compliant equipment only shows “protected” content on
HDCP compliant displays.
Please note the following important points:
•
When an HDCP compliant device is connected to the DCS-200 and that specific
input is selected, the Status Menu indicates if HDCP is enabled.
•
If the “session” determines that the target display device is non-HDCP compliant
(e.g., if the user is attempting to make an illegal copy on an external recorder), an
error message appears on the DCS-200’s Status Menu, indicating that video
cannot be shown.
•
HDCP compliant repeaters cannot be connected to the output of the DCS-200, as
the DCS-200 must be the last device in the HDCP "chain" — prior to the HDCP
compliant display. If an HDCP repeater is connected, the message “HDCP
Violation” appears on the Status Menu. In Chapter 4, refer to the “Status Menu”
section on page 44 for additional details.
DCS-200 • User’s Guide
17
NK==fåíêçÇìÅíáçå
Connectivity Diagram
`çååÉÅíáîáíó=aá~Öê~ã
The figure below illustrates a basic DCS-200 system.
Sample Source Input
Devices
Preview
Inputs 1 - 6 (Analog)
DCS-200
Inputs 7 - 8 (DVI)
Program
Input 9 (HD/SD SDI)
Ethernet
Serial
Figure 1-1. Block diagram, DCS-200 system
In the diagram:
•
•
•
Up to nine sources can be connected to the DCS-200:
~
6 x analog inputs (on HD-15 connectors), for a variety of YUV and
RGBHV sources, including CVBS and Y/C.
~
2 x DVI inputs, for computer sources. These two DVI connectors also
support analog RGB inputs, and these inputs are universal, and accept
all types of sources — just like the six HD-15 connectors. (To connect
analog sources, use a customer-supplied DVI to HD-15 adapter.)
~
1 x SD-SDI or HD-SDI input.
The DCS-200 connects to a Preview monitor via analog or DVI.
The DCS-200 connects to a projector (or other target device) via analog or DVI.
In Chapter 2, refer to the “Inputs Section” heading on page 22 for details on all inputs.
^ééäáÅ~íáçå=nìÉëíáçåë
At Barco, we take pride in offering unique solutions to demanding technical problems. If
you have application questions, require further information or would like to discuss your
application requirements in more detail, please call (866) 469-8036. Our Customer
Support Engineers will be happy to supply you with the support you need. Refer to
Appendix C, “Contact Information” on page 159 for details.
18
DCS-200 • User’s Guide
OK==e~êÇï~êÉ=lêáÉåí~íáçå
få=qÜáë=`Ü~éíÉê
This chapter provides detailed diagrams of the DCS-200’s front and rear panels, along with
comprehensive explanations of each.
The following topics are discussed:
•
•
DCS-200 • User’s Guide
DCS-200 Front Panel
DCS-200 Rear Panel
19
2. Hardware Orientation
DCS-200 Front Panel
a`pJOMM=cêçåí=m~åÉä
The figure below illustrates the DCS-200 front panel:
1
2
Inputs
PROGRAM:
NEXT:
RGB
1 02 4 x 76 8 @ 5 9.9 4
SDI
N T S C (4 8 0i)
1
SEL
A djust
2
3
4
5
6
7
8
SDI
LOGO
DCS-200
ESC
E ffects
FR Z
B LA C K
3
KEY
TA KE
4
Figure 2-1. DCS-200 Front Panel
1)
Display Section
3)
Effects Section
2)
Inputs Section
4)
Take Button
Following are descriptions of each front panel section:
1)
Display Section
The Display Section includes a four-line display, the ADJUST knob and two
“menu navigation” buttons: SEL and ESC. Refer to the “Display Section”
heading on page 21 for complete details.
2)
Inputs Section
The Inputs Section includes ten “source” buttons that enable you to select inputs,
key sources and a full screen LOGO. Refer to the “Inputs Section” heading on
page 22 for complete details.
3)
Effects Section
The Effects Section provides three buttons that enable you to select the type of
effect that you want to perform next. Refer to the “Effects Section” heading on
page 23 for complete details.
4)
Take Button
The red TAKE button initiates a transition to the selected source. Refer to the
“Take” section on page 24 for details.
20
DCS-200 • User’s Guide
2. Hardware Orientation
DCS-200 Front Panel
aáëéä~ó=pÉÅíáçå
The figure below illustrates the Display Section:
PROGRAM:
NEXT:
RGB
1024x768 @59.94
SDI
NTSC (480i)
SEL
Adjust
ESC
Figure 2-2. Display Section with sample Status Menu
Descriptions of each button and control are provided below:
•
The Menu Display is a 4-line x 20-character Vacuum Fluorescent Display (VFD)
that shows all DCS-200 menus and sub-menus. Brightness is adjustable. The
following illustration shows a typical DCS-200 menu.
SE TUP ME NU
> T r a ns T i m e
Output
Pr eview
1.0
>>
>>
Figure 2-3. Sample Setup Menu Display
For all setup menus, please note:
~
~
The top line names the current menu, in all capital letters.
~
The double arrow (>>) indicates that a sub-menu is available.
Note
The navigation cursor (>) in the left-hand column indicates the current
line on which action can be taken.
The Status Menu layout is different from the “setup” menu
display. In Chapter 4, refer to the “Status Menu” section on
page 44 for details.
In Chapter 4, refer to the “Menu Tree” section on page 38 for additional details on
the system’s menu tree.
•
ADJUST — use the Adjust Knob to scroll through all system menus.
~
~
•
SEL
DCS-200 • User’s Guide
Turn the knob counter-clockwise (CCW) to scroll down.
Turn the knob clockwise (CW) to scroll up.
SEL — press to enter the setup menu tree (from the Status Menu), to enter a
sub-menu, change a parameter, accept a parameter, or to answer “Yes” to certain
menu queries.
21
2. Hardware Orientation
DCS-200 Front Panel
•
ESC
ESC — press to exit a menu without making changes, cancel an operation, to
answer “No” to certain menu queries, and to return to the top Status Menu. Each
press takes you back up the menu tree by one level.
fåéìíë=pÉÅíáçå
The figure below illustrates the Inputs Section:
Inputs
1
2
3
4
5
6
7
8
SDI
LOGO
Figure 2-4. Inputs Section
The buttons in the Inputs Section enable you to select the source that you want to
transition to Program. Each button corresponds to the similarly numbered input connector
on the rear panel. You can also select the full screen LOGO as the transition source.
There are three button states:
•
•
Off — the input is not selected for a transition.
Blinking — the input is “pending” for the next transition.
~
~
Note
•
When a button is blinking fast, it is being acquired by the system.
When a button is blinking slow, it is ready to be transitioned to Program.
If an input button is blinking slow, and the Status Menu
shows “Invalid Signal,” the system has attempted to acquire
the source, but has failed.
Lit Solid — the input is on Program.
In Chapter 4, refer to the “Flip-flop Mode” section on page 85 for additional information
about button behavior when TAKE is pressed.
Following are descriptions of each “input” button in the section:
1
22
•
Buttons 1 through 6 enable you to select physical inputs 1 through 6 (respectively)
from the rear panel HD-15 connectors.
•
Buttons 7 and 8 enable you to select physical inputs 7 and 8 (respectively) from
the rear panel DVI-I connectors. Please note:
~
If a DVI signal is present, the DVI (digital) source is used from the DVI-I
connector’s digital pins.
~
If a DVI signal is not present, the selection defaults to the analog signals
that are on the DVI-I connector’s analog pins. Note that a customersupplied DVI to HD-15 adapter is required to connect to the analog pins.
DCS-200 • User’s Guide
2. Hardware Orientation
DCS-200 Front Panel
SDI
•
The SDI button selects the SD-SDI or HD-SDI input source.
•
The LOGO button selects the stored “full screen” LOGO image for the next
transition. If no image is stored, the transition will be to Black. Use the menu to
select one of three stored LOGOs for use. In Chapter 4, refer to the “Using the
LOGO” section on page 88 for details.
LOGO
Note
If you press a button in the Inputs Section, it blinks to
indicate “pending.” If you do not want to pend a source
(which may be desirable in some situations), press the
blinking source button again. The button turns off, leaving
only the source on Program lit solid.
bÑÑÉÅíë=pÉÅíáçå
The figure below illustrates the Effects Section:
Effects
FRZ
BLACK
KEY
Figure 2-5. Effects Section
The buttons in the Effects Section enable you to freeze the selected source on Program,
transition to black, and perform a key over the selected Program source.
Following are descriptions of each “effects” button:
•
The FRZ button instantly freezes and unfreezes the current Program source.
When the source is frozen, the button is lit solid. In Chapter 4, refer to the “Using
Freeze” section on page 92 for details.
•
The BLACK button enables you to transition to or from black. The button
performs one of two functions, depending on the way the button is defined in the
User Preferences Menu.
FRZ
BLACK
~
DCS-200 • User’s Guide
If “Black Auto Take” is Off:
•
Press BLACK to pend a transition to or from black. The button
blinks to indicate “pending.”
•
Press TAKE to perform the transition to or from black.
– If the transition is “to” black, the button lights solid
when black is on Program.
– If the transition is “from” black, the button turns off
when the selected source is fully on Program.
23
2. Hardware Orientation
DCS-200 Front Panel
~
If “Black Auto Take” is On:
•
Press BLACK to immediately transition to/from black.
– If the transition is “to” black, the button blinks fast
during the transition, then lights solid when black is on
Program.
– If the transition is “from” black, the button blinks fast
during the transition, then turns off when the selected
source is on Program.
Important
Regardless of the current Black Auto Take mode, if you
select (or pend) BLACK, the system will not transition to the
selected “next” source until black is fully on Program.
In Chapter 4, refer to the “Using Black” section on page 93 for details.
•
KEY
The KEY button enables you to key an un-scaled DVI source (input 7 or 8) over
the current Program source. The key’s clip, gain, opacity, and the selected key
source are adjusted using the menu. The button performs one of two functions,
depending on the way the button is defined in the User Preferences Menu.
~
If “Key Auto Take” is Off:
•
Press KEY to pend a “key up” or “key down” transition. The
button blinks to indicate “pending.”
•
Press TAKE to perform the key transition at the current rate.
– If the transition is a “key up,” the button lights solid
when the key is on.
– If the transition is a “key down,” the button
automatically turns off when the key is off.
~
If “Key Auto Take” is On:
•
Press KEY to immediately perform the “key up” or “key down”
transition at the current rate.
– If the transition is a “key up,” the button blinks fast
during transition, then lights solid when the key is on.
– If the transition is a “key down,” the button blinks fast
during transition, then turns off when the key is off.
In Chapter 4, refer to the “Using Keys” section on page 95 for details.
q~âÉ=
TAKE
Press TAKE to mix the pending (blinking) source to Program, at the current transition rate.
Using the Setup Menu, you can adjust the transition time from 0 to 12 seconds. If the
transition time is set to 0, the transition is a cut. Please note:
•
Each time TAKE is pressed, the current source on Program and the pending
source flip-flop. In Chapter 4, refer to the “Flip-flop Mode” section on page 85 for
additional details.
•
The TAKE button is also used to transition a “key” up or down, when the “Key
Auto Take” function is On in the User Preferences Menu.
•
The TAKE button is also used to transition to/from black, when the “Black Auto
Take” function is On in the User Preference Menu.
In Chapter 4, refer to the “User Preference” section on page 70 for details on the User
Preference Menu.
24
DCS-200 • User’s Guide
2. Hardware Orientation
DCS-200 Rear Panel
a`pJOMM=oÉ~ê=m~åÉä
The figure below illustrates the DCS-200 rear panel:
8
Model
DCS-200
PREVIEW OUTPUTS
100 - 240 VAC
50 – 60 Hz, 1.9A
Input 1
Input 3
Input 5
Input 2
Input 4
Input 6
VIDEO INPUTS
MAIN OUTPUTS
HD/SD SDI
Input 7
SERIAL
ETHERNET
5
6
Input 8
1
2
3
4
7
Figure 2-1. DCS-200 Rear Panel
1)
Analog Inputs
4)
Main Outputs
7)
AC Power
2)
DVI and Analog Inputs
5)
Serial
8)
Preview Outputs
3)
HD/SD SDI Input
6)
Ethernet
Following are descriptions of each rear panel connector:
1)
Analog Inputs
Six HD-15 connectors are provided for the system’s Analog inputs. Please note:
~
~
Each input provides 10-bits/color sampling at a maximum 165 MHz.
~
Composite and S-Video formats are supported.
Each input supports 1:1 sampling up to 1600x1200@60 Hz. Sources
with native pixel rates greater than 165 MHz will be filtered and
undersampled at 165 Mhz. These include:
•
1920x1080p@60 (173.0 MHz)
•
1920x1200@60 (193.25 MHz)
•
2048x1080p@60 (183.75 MHz)
In Chapter 3, refer to the “Format Connection Table” section on page 32 for a
table of analog inputs that you can connect using a customer-supplied breakout
cable. In Appendix A, refer to the “Analog 15-pin D Connector” section on
page 118 for pinouts.
2)
DVI and Analog Inputs
Two DVI-I connectors are provided for both digital and analog inputs.
~
~
Using the connector’s digital pins, an 8-bit digital input is supported.
Using the connector’s analog pins, RGBHV, analog composite, S-Video,
and YUV formats are supported. A customer-supplied breakout cable or
DVI to HD-15 adapter is required for these connections.
In Appendix A, refer to the “DVI-I Connector” section on page 119 for pinouts.
DCS-200 • User’s Guide
25
2. Hardware Orientation
DCS-200 Rear Panel
3)
HD/SD SDI Input
One BNC connector is provided for the SD-SDI or HD-SDI input.
4)
Main Outputs
Two connectors are provided for the DCS-200’s main program outputs. Both
outputs have the same resolution, and both can be used simultaneously.
~
One DVI-I connector is provided for the system’s digital program output.
There are no analog outputs on this connector. In Appendix A, refer to
the “DVI-I Connector” section on page 119 for pinouts.
Note
~
5)
The DVI-I connector allows you to use both DVI-D and DVI-I
cables as required.
One HD-15 connector is provided for the system’s analog output. In
Appendix A, refer to the “Analog 15-pin D Connector” section on
page 118 for pinouts
Serial
One DB-9 connector is provided for Serial communications with the DCS-200
system. The port is also used for diagnostics or command-line operations.
6)
Ethernet
One RJ-45 connector is provided for 10/100BaseT Ethernet communications with
the DCS-200 system. The port is used for running the built-in web-based GUI, for
diagnostics, or for command-line operations via Telnet (using port 23).
S telnet 192.168.0.10 23
In Appendix A, refer to the “Ethernet Connector” section on page 120 for
pinouts.
7)
AC Power
One AC Connector is provided for connecting DCS-200 to AC. The integral
switch turns the chassis on and off. In Appendix A, refer to the “Physical and
Electrical Specifications” section on page 117 for power details.
8)
Preview Outputs
Two outputs are provided for connecting to the Preview monitor: an HD-15
connector for analog monitors and a DVI connector for digital displays.
26
DCS-200 • User’s Guide
PK==fåëí~ää~íáçå
få=qÜáë=`Ü~éíÉê
This chapter provides detailed instructions for installing the DCS-200 hardware. The
following topics are discussed:
•
•
•
•
•
•
•
•
DCS-200 • User’s Guide
Safety Precautions
Unpacking and Inspection
Site Preparation
Cable and Adapter Information
Rack-Mount Installation
Power Installation
Signal Installation
Format Connection Table
27
3. Installation
Safety Precautions
p~ÑÉíó=mêÉÅ~ìíáçåë=
For all DCS-200 installation procedures, observe the following important safety and
handling rules to avoid damage to yourself and the equipment:
•
To protect users from electric shock, ensure that the power supplies for each unit
connect to earth via the ground wire provided in the AC power cord.
•
The AC Socket-outlet should be installed near the equipment and be easily
accessible.
råé~ÅâáåÖ=~åÇ=fåëéÉÅíáçå=
Inspect the shipping box for damage. If you find any damage, notify the shipping carrier
immediately for all claims adjustments. As you open the box, compare its contents against
the packing slip. If you find any shortages, contact your Barco sales representative.
Once you have removed all the components from their packaging and checked that all the
listed components are present, visually inspect each unit to ensure there was no damage
during shipping. If there is damage, notify the shipping carrier immediately for all claims
adjustments.
páíÉ=mêÉé~ê~íáçå=
The environment in which you install your DCS-200 should be clean, properly lit, free from
static, and have adequate power, ventilation, and space for all components.
`~ÄäÉ=~åÇ=^Ç~éíÉê=fåÑçêã~íáçå
The table below provides information regarding supplied cables and adapters:
Table 3-1. DCS-200 Cables and Adapters
Cable / Adapter
Description
Quantity
AC Power Cord
7 foot, 10A (US Power Cord)
1
AC Power Cord
7 foot, 10A (European Power Cord)
1
28
DCS-200 • User’s Guide
3. Installation
Rack-Mount Installation
o~ÅâJjçìåí=fåëí~ää~íáçå
DCS-200 units are designed to be rack mounted and are supplied with front rack-mount
hardware. Please note the following important points:
•
When rack mounting the unit, remember that the maximum ambient operating
temperature for the unit is 40 degrees C.
•
Leave sufficient front and rear space to ensure that the airflow through the fan and
vent holes is not restricted.
•
When installing equipment into a rack, distribute the units evenly to prevent
hazardous conditions that may be created by uneven weight distribution.
•
•
•
Connect the unit only to a properly rated supply circuit.
•
Install the lower of the two mounting holes first.
Reliable grounding (earthing) of rack-mounted equipment should be maintained.
Rack mount the unit from the front rack ears using four rack screws (not supplied).
Rack threads may be metric or otherwise — depending upon the rack type.
mçïÉê=fåëí~ää~íáçå
„ Use the following steps to install power to the DCS-200:
1.
Connect an AC power cord to the AC Power Connector on the rear of the
DCS-200, and then to an AC outlet.
2.
Connect AC Power cords (or AC adapters) to all peripheral equipment, such as
video sources, VTRs and PCs. Please note:
~
~
DCS-200 • User’s Guide
Connect each unit only to a properly rated supply circuit.
Reliable grounding of rack-mounted equipment should be maintained.
29
3. Installation
Power Installation
mçïÉê=`çêÇLiáåÉ=sçäí~ÖÉ=pÉäÉÅíáçå
DCS-200 is rated to operate with the following specifications:
•
•
Input Power: 100-240 VAC, 50-60 Hz
Power Consumption: 240 watts maximum
DCS-200 performs line voltage selection automatically, and no user controls are required.
The AC power cords must be accessible so that they can be removed during field servicing.
Warning
When the DCS-200 is used in the 230-volt mode, a UL listed
line cord rated for 250 volts at 15 amps must be used and
must conform to IEC-227 and IEC-245 standards. This cord
will be fitted with a tandem prong-type plug.
The rear panel ON/OFF switch does not disconnect the unit
from input AC power. To facilitate disconnection of AC
power, the power cord must be connected to an accessible
outlet near the unit.
Building Branch Circuit Protection: For 115 V use 20 A, for
230 V use 8 A.
Figure 3-1. Tandem Prong-type Plug
Avertissement
Warnung
30
La choix de la ligne de voltage se réalise automatiquement
par le DCS-200 Transformateur Graphique. On n'a pas
besoin du controller usager pour la choix de la ligne de
voltage.
Das DCS-200 gerät mu beim Anschlu an 240V ~ mit einer
vom VDE auf 250V/10A geprüften Netzleitung mit einem
Schukostecker ausgestattet sein.
DCS-200 • User’s Guide
3. Installation
Signal Installation
páÖå~ä=fåëí~ää~íáçå
The figure below illustrates a sample DCS-200 system. Use this figure for reference during
the signal installation process.
Sample Source Input
Devices
Program
Preview
Inputs 1 - 6 (Analog)
DCS-200
DVI
Inputs 7 - 8 (DVI)
Program
Input 9 (HD/SD SDI)
Ethernet
Serial
Analog
Figure 3-2. DCS-200 System Diagram (sample)
„ Use the following steps to install signals to/from the DCS-200:
1.
2.
DCS-200 • User’s Guide
Input connections — any combination of inputs can be connected.
a.
As required, connect analog RGBHV sources to Inputs 1 through 6.
Refer to the “Format Connection Table” section on page 32 for a table
of analog input combinations.
b.
As required, connect DVI sources to Inputs 7 and 8 (using the
connector’s digital pins).
c.
As required, connect analog sources to Inputs 7 and 8 (using the
connector’s analog pins). A customer-supplied breakout cable or DVI to
HD-15 adapter is required for this connection.
d.
As required, connect an HD-SDI or SD-SDI source to Input 9.
Output connections — up to three outputs can be connected:
a.
If you are connecting the DCS-200 to a digital projector (for example) or
other target device, connect the DVI Output to the projector’s DVI input.
b.
If you are connecting the DCS-200 to an analog projector (for example)
or other target device, connect the Analog (HD-15) Output to the
projector’s analog input.
c.
If you are connecting the DCS-200 to a Preview monitor, connect the
Preview DVI or Analog (HD-15) Output to the monitor.
31
3. Installation
Format Connection Table
3.
GUI connection — to configure your system to run from the built-in web-based
GUI, perform the following steps:
a.
Ensure that your PC (or laptop) uses Windows® 2000 or XP.
b.
Ensure that your PC (or laptop) has a web browser installed, such as
Windows Internet Explorer® or Mozilla Firefox®.
c.
Ensure that your PC is using Java Version 6 or later.
d.
Connect the DCS-200’s Ethernet port to a Switch.
e.
Connect the Switch to your PC (or laptop).
This completes the required “physical” connections. Refer to Chapter 5, “GUI
Operations” on page 103 for installation and operating instructions.
4.
Communications connection — two methods are available for remote control:
a.
Connect the DCS-200’s Ethernet port to an Ethernet switch, and
connect the switch to the other Ethernet devices in your local system.
This enables you to communicate with the DCS-200 via Telnet. In
Appendix B, refer to the “Communicating with DCS-200” section on
page 127 for details.
b.
For a serial remote connection, connect the DCS-200’s Serial port to the
serial port of a laptop or a PC. In Appendix B, refer to the
“Communicating with DCS-200” section on page 127 for details
This completes system signal installation. Please continue with system setup, menu
orientation and operations, as outlined in Chapter 4, “Operation” on page 33.
cçêã~í=`çååÉÅíáçå=q~ÄäÉ
Use the following table to connect various source formats to the DCS-200, using the analog
HD-15 connectors (on Inputs 1 through 6). Please note:
•
•
RGB format — typical devices: Computers
YUV or YPbPr (Betacam) format — typical devices: DVD player, Betacam deck
Using a customer supplied VGA to 5 x BNC breakout cable, multiple input combinations
are possible. Cells with checks denote the connections required for the indicated format.
Table 3-2. Analog Input Combinations using Breakout Cable
Breakout Cable
Wire Color
Composite
Video
S-Video
(Y/C)
B
H Sync
V Sync
3
RGB
Sync on Green
RGB
Comp Sync
RGB
Separate H V
3 (Pr)
3
3
3
3 (Lum)
3 (Lum)
3
3
3
3 (Chrom)
3 (Pb)
3
3
3
3
3
R
G
YUV
(YPbPr)
3
Please contact Barco Technical Support for information on obtaining breakout cables. In
Appendix C, refer to the “Contact Information” section on page 160 for details.
32
DCS-200 • User’s Guide
QK==léÉê~íáçå
få=qÜáë=`Ü~éíÉê
This chapter provides comprehensive menu descriptions and detailed operating
instructions for the DCS-200. The following topics are discussed:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
DCS-200 • User’s Guide
Control Overview
Power-Up Initialization
Button States
Quick Setup and Operations
Menu Tree
Using the Menu System
Quick Function Reference
Status Menu
Using the Setup Menu
Using Inputs
Using the LOGO
Using Freeze
Using Black
Using Keys
Understanding Front-Panel Lockout
33
4. Operation
Control Overview
`çåíêçä=lîÉêîáÉï
There are several ways to control the DCS-200:
•
The front panel is ideal for all basic operations. Available controls include the
Display Section and the buttons in the Inputs Section and the Effects Section.
•
The built-in web-based GUI is ideal for intuitive point-and-click operations. Refer
to Chapter 5, “GUI Operations” on page 103 for additional details.
•
The DCS-200 can also be controlled remotely via Ethernet or Serial
communications. See Appendix B “Remote Control” on page 127 for additional
details.
mçïÉêJré=fåáíá~äáò~íáçå
After connecting power to the DCS-200, locate the power switch on the back of the chassis,
and turn power ON. While the system is initializing, the following messages are displayed:
DCS-200
Ba rco
Initializing...
Figure 4-1. System Initialization Message 1 (sample)
Program Loading
ple ase wait...
Figure 4-2. System Initialization Message 2 (sample)
Transferring to
ma in pro gram .
Figure 4-3. System Initialization Message 3 (sample)
34
DCS-200 • User’s Guide
4. Operation
Button States
DCS-200
Ba rco
Version 1.0
Initializing...
Figure 4-4. System Initialization Message 4 (sample)
The “version” line in the above menu shows the software version that is currently installed.
This version number changes as software upgrades are released.
When you first start up a DCS-200 that has stored logos, a message like the one in the
following illustration appears during initialization:
LOGO1 loading. ..
5%
Figure 4-5. LOGO Initialization Message (sample)
After system initialization is complete, the Status Menu appears.
_ìííçå=pí~íÉë
Remember that there are three states for the buttons in the Inputs Section:
•
•
•
Off — the input is not selected for a transition.
Blinking — the blinking status depends on the type of button:
~
For an input button:
•
When blinking fast, the input is being acquired by the system.
•
When blinking slow, the input is ready to be transitioned to
Program.
~
For an effect button (BLACK, KEY):
•
When blinking fast, the button’s “auto take” mode is ON, and
the effect is currently transitioning on or off.
•
When blinking slow, the button’s “auto take” mode is OFF, and
the effect is pending for the next transition.
Lit Solid — the input or the effect is on Program.
Remember also that when you press TAKE, the DCS-200 automatically flip-flops the
current source on Program with the “pending” source. Refer to the “Flip-flop Mode”
section on page 85 for additional information.
DCS-200 • User’s Guide
35
4. Operation
Quick Setup and Operations
nìáÅâ=pÉíìé=~åÇ=léÉê~íáçåë
For the optimum speed in setting up and operating your system, use the following steps.
For reference, links are provided to the appropriate sections in this guide.
1.
Connect power — Ensure that power is properly connected to the DCS-200.
(Chapter 3, “Power Installation,” page 29.)
2.
Connect inputs — Connect all input sources to the DCS-200. (Chapter 3,
“Signal Installation,” page 31.
3.
Connect outputs — Connect the output(s) of the DCS-200 to your projector(s) or
other target devices. (Chapter 3, “Signal Installation,” page 31.
4.
Turn on power — Turn on power to the DCS-200, your projector(s), and to all
peripheral equipment. (This chapter, “Power-Up Initialization,” page 34.)
5.
Factory reset — If you are using the DCS-200 for the first time, or if you are using
a DCS-200 that has just returned from another event, perform a full factory reset
to restore system configurations. (This chapter, “Factory Reset,” page 82.)
6.
Launch GUI — (Optional) If you want to run the system from the web-based GUI,
ensure that Ethernet is connected between your PC and the DCS-200, then
launch the GUI. (Chapter 5, “GUI Operations,” page 103.)
7.
Set output format — Set the desired output resolution and frame rate. (This
chapter, “Output Format,” page 48.)
8.
Enable test pattern — Turn on the desired test pattern, verify that you have an
image, and make the necessary adjustments. When complete, turn off the test
pattern. (This chapter, “Test Pattern,” page 48.)
9.
Save output configuration — After completing all output adjustments, save the
output configuration. (This chapter, “Save Output Config,” page 49.)
10. Select and adjust inputs — As required, select an input, and perform the
necessary adjustments. (This chapter, “Input Menu,” page 53.)
11. Save input configuration — After completing all adjustments for an input, save
the input configuration. (This chapter, “Save Config,” page 64.)
12. Repeat for each input — repeat steps 9 and 10 for each input that you have
connected to the DCS-200.
13. Adjust key source — As required, select the desired key source, and adjust its
clip, gain and opacity. (This chapter, “Using Keys,” page 95.)
14. Adjust system parameters — As required, adjust all desired system parameters
such as transition time, display brightness, and all user preferences. (This
chapter, “Trans Time,” page 47 and “System Menu,” page 73.)
15. Save system configuration — After completing all system adjustments, save the
system configuration. (This chapter, “Save System State,” page 81.)
16. (Optional) Remote Control — To control the DCS-200 remotely, ensure that
Ethernet or Serial communications are connected, then establish communications
and issue commands. (Appendix B, “Remote Control,” page 127.)
36
DCS-200 • User’s Guide
4. Operation
Quick Setup and Operations
17. Ready to roll — With all output, input and system configurations saved, press the
desired input button, and press TAKE.
Note
DCS-200 • User’s Guide
For advanced system operations, specific system “tweaks”
and operating descriptions on every feature, please start with
the “Quick Function Reference” section on page 41, and
select the function that you wish to perform.
37
4. Operation
Menu Tree
jÉåì=qêÉÉ
The figure below illustrates the entire DCS-200 menu tree. Please use this diagram for
reference as you learn how to operate the system.
Status Menu
Setup Menu
Trans Time
Output
Output Format
Test Pattern
Preview
Output Src
Input
Input Format
Key Setup
Input
LOGO Setup
Selection
User Preference
System
In Auto Acquire
VFD Brightness
Ethernet
Tech Support
Version
Output Format
Adjust On
Clip
Status
Auto Input Cfg
Mode
Test Pattern
Type
Gain
Save LOGO
Auto Input Save
DHCP
Type
Sync Setup
Colorspace
Opacity
Delete LOGO
Auto Take
Config Network
Raster Box
Save
Background
H Offset
Black Auto Take
Set Static IP
Timing Adjust
V Offset
Key Auto Take
Set Netmask
Sync Setup
Analog Sync
DVI Sync
Auto Config *
Gamma
Phase B
Save Config
H Total
IP
M
Serial Setup
H Position
Baud
H Active
Use Timing Adjust for analog
input sources except NTSC
and PAL.
V Total
V Position
V Active
Use Image Adjust for DVI,
SDI, NTSC and PAL input
sources.
Image Adjust
Auto Config *
H Size
Parameters
Handshaking
Reset
EDID Setup
Input
EDID Format
Type
V Size
DVI Cable EQ
H Pan
Input
V Pan
Equalization
Aspect Ratio
Reset All
Set to Default
Set to Maximum
Contrast
Set to Minimum
Brightness
Executive Mode
Color Balance
Red Contrast
File Association
Input 1
Grn Contrast
Input 2
RGB
Red Bright
Grn Bright
Blue Contrast
Input 3
Input 4
Input 5
Reset All
Input 6
Hue
Reset All
SDI
Comp
YPbPr
S-Video
Blue Bright
Saturation
Factory Reset
Set Gateway
Menu Context
Sampling
Phase A
Phone
Processing
Sync Sel
Pulldown Cmp
Sync Slice
Reset Config
Save Config
Input 7
Input 8
SDI
Temperature
Temp °F
Temp °C
Diagnostics
Start Tests
Save State
Delete Config
Recall Config
Figure 4-6. DCS-200 Menu Tree
* The “Auto Config” selection is only available when an analog input is chosen.
38
DCS-200 • User’s Guide
4. Operation
Using the Menu System
rëáåÖ=íÜÉ=jÉåì=póëíÉã
This section lists the rules and conventions for using DCS-200’s menu system. For
reference, the figure below illustrates the Setup Menu:
SE TUP ME NU
> T r a ns T i m e
Output
Pr eview
1.0
>>
>>
Figure 4-7. Setup Menu (sample)
For all setup menus, please note the following important menu rules and conventions:
•
•
The top line names the current menu, in all capital letters.
Subsequent lines typically display two fields:
~
For a listed function, the left-hand field names the function, and the
right-hand field is the function’s current parameter or value.
~
For a listed sub-menu, the left-hand field names the sub-menu that you
can access, and the right-hand field displays the double arrow (>>),
indicating that a sub-menu is available.
•
The “navigation” cursor (>) in the left-hand column indicates the current line on
which action can be taken. This arrow “scrolls” as you rotate the knob.
•
Scrolling:
~
~
•
Turn the ADJUST knob counter-clockwise (CCW) to scroll down.
Turn the ADJUST knob clockwise (CW) to scroll up.
To enter a sub-menu, scroll to the desired line and press SEL.
Note
Throughout this chapter, the term “select” is used as an
abbreviation for “scroll to a menu line and press SEL.”
S Select the Input field to...
•
To change a parameter, scroll to the desired line and press SEL. The cursor
changes to the “edit” cursor (#). Use the ADJUST knob to modify the value:
~
~
•
Turn the ADJUST knob CW to increase a value.
Turn the ADJUST knob CCW to decrease a value.
To accept a parameter or value, press SEL. The edit cursor changes back to the
navigation cursor.
Note
You must press SEL to activate a DCS-200 function.
•
In the “edit” mode, to exit (or cancel) without changing the original parameter,
press ESC.
•
To navigate back up the menu structure, press ESC. Each press takes you back
up the menu tree by one level.
DCS-200 • User’s Guide
39
4. Operation
Using the Menu System
•
The SEL button is also used to answer “Yes” to certain menu queries. The ESC
button is also used to answer “No” to certain menu queries.
Note
•
40
The display itself is four lines high, and the ADJUST knob is
used to scroll through the various lines. Throughout this
chapter, entire menus will be shown for clarity — rather than a
series of four-line sections.
If a value is displayed between brackets, (e.g., [SMPTE]) this indicates that the
value can not be changed.
DCS-200 • User’s Guide
4. Operation
Quick Function Reference
nìáÅâ=cìåÅíáçå=oÉÑÉêÉåÅÉ
Use the following table to quickly access the proper section for a specific function. Both
hyperlinks and page numbers are provided.
Table 4-1. DCS-200 Quick Function Reference Table
How to:
Use the Following Section:
Page
Adjust background color
Background
57
Adjust gamma
Gamma
49
Adjust image brightness
Brightness
61
Adjust image color balance
Color Balance
62
Adjust image contrast
Contrast
61
Adjust input processing
Processing
63
Adjust input timing
Timing Adjust
57
Adjust the image
Image Adjust
60
Adjust transition time
Trans Time
47
Associate configuration files to inputs
File Association Menu
79
Check software version
Tech Support
82
Contact Tech Support
Tech Support
82
Delete input configuration
Delete Config
65
Display a test pattern
Test Pattern
48
Display the raster box
Test Pattern
48
Identify button states
Button States
35
Learn the menu tree
Menu Tree
38
Lock out the front panel completely
Full Lockout Mode
101
Lock out the front panel, except inputs
Executive Lockout Mode
101
Perform a key
Performing a Key
96
Perform factory reset
Factory Reset
82
Perform key combinations
Key Transition Combinations
97
Perform quick setup and operations
Quick Setup and Operations
36
Perform system diagnostics
Diagnostics
81
Power up the system
Power-Up Initialization
34
Reset input configuration
Reset Config
64
Reset system
Factory Reset
82
Save input configuration
Save Config
64
DCS-200 • User’s Guide
41
4. Operation
Quick Function Reference
Table 4-1. DCS-200 Quick Function Reference Table (Continued)
How to:
Use the Following Section:
Page
Save output configuration
Save Output Config
49
Save system state
Save System State
81
Select inputs
Input Selection Rules
84
Set Auto Input Config mode
Auto Input Config
71
Set Auto Input Save mode
Auto Input Save
72
Set Auto Take mode
Auto Take
72
Set Black Auto Take mode
Black Auto Take
72
Set color input space
Colorspace
56
Set DVI cable equalization
DVI Cable Equalization
79
Set Ethernet parameters
Ethernet
74
Set In Auto Acquire mode
In Auto Acquire
70
Set input format
Input Format
55
Set input type
Type
56
Set Key Auto Take mode
Key Auto Take
72
Set Menu Context mode
Menu Context
73
Set or change multiple input configurations
File Association Menu
79
Set or change a single input configuration
Recall Config
66
Set output format
Output Format
48
Set Preview or Program mode
Adjust On
55
Set Serial port parameters
Serial Setup
76
Set up EDID
EDID Setup
77
Set up Key
Key Setup Menu
67
Set up LOGO
LOGO Setup Menu
69
Set up sync
Sync Setup
49
Set user preferences
User Preference
70
Set VFD brightness
VFD Brightness
73
Understand auto acquire
Understanding Auto Acquire
86
Use Black
Using Black
93
Use Freeze
Using Freeze
92
Use HDCP
Using HDCP
86
Use inputs
Using Inputs
84
Use Keys
Using Keys
95
Use the Input Menu
Input Menu
53
42
DCS-200 • User’s Guide
4. Operation
Quick Function Reference
Table 4-1. DCS-200 Quick Function Reference Table (Continued)
How to:
Use the Following Section:
Page
Use the Key Setup Menu
Key Setup Menu
67
Use the LOGO
Using the LOGO
88
Use the LOGO Setup Menu
LOGO Setup Menu
69
Use the menu system
Using the Menu System
39
Use the Output Menu
Output Menu
47
Use the Preview Menu
Preview Menu
50
Use the Setup Menu
Using the Setup Menu
46
Use the Status Menu
Status Menu
44
Use the System Menu
System Menu
73
Use the User Preference Menu
User Preference
70
View chassis temperature
Temperature
80
View LOGO status
LOGO Setup Menu
69
View software version
Tech Support
82
View Tech Support number
Tech Support
82
DCS-200 • User’s Guide
43
4. Operation
Status Menu
pí~íìë=jÉåì
The Status Menu is the system’s top level display, which appears by default after the
DCS-200 boots up.
•
To return to the Status Menu from any point within the Setup Menu, press ESC
repeatedly.
•
To display the Setup Menu from the Status Menu, press SEL.
The figure below illustrates a sample Status Menu:
PROGRAM:
NE XT :
RGB
102 4x768@59. 94
SDI
NTSC (480i)
— Program Input Type
— Program Input Format
— Next Input Type
— Next Input Format
Figure 4-8. Status Menu (sample)
The Status Menu provides information about the current input on Program (the button that
is lit solid), and the input that is next to be transitioned to Program (the button that is
blinking). The Status Menu always updates as “current” and “next” sources change.
Please note:
•
If Menu Context is ON (in the User Preference Menu), selecting a different input
for the “next” transition automatically displays the Input Menu. This menu always
reflects the source currently on Program. To return to the Status Menu, press
ESC repeatedly.
•
If Menu Context is OFF, the Status Menu remains on display when you select a
different input.
In the Status Menu, the variable fields are as follows:
•
•
Program Input Type — Specifies the type of input signal currently on Program.
Program Input Format — Indicates the current input video format, in the form:
Hact x Vact @ Vr Hz
S 1280x1024@60 Hz
If the currently selected input does not have a valid input signal, the Input Format
field displays Invalid Signal.
Please note the following conventions for displaying resolutions:
Table 4-2. Status Menu Conventions
Convention
44
Description
Hact x Vact @ Vr
No symbols. The current format is an exact match from the table. The
format has not been “best guessed” or saved.
*Hact x Vact @ Vr*
Asterisks. The format has been “best guessed.”
[Hact x Vact @ Vr]
Brackets. The exact table match has been saved.
[*Hact x Vact @ Vr*]
Brackets plus Asterisks. The best guessed format has been saved.
DCS-200 • User’s Guide
4. Operation
Status Menu
•
Next Input Type — indicates the next input type on Program, and (if applicable),
the system’s HDCP status. The following labels can appear, depending on the
output and HDCP implementation:
~
~
HDCP
HDCP Violation
Important
•
If the label “HDCP Violation” appears, an HDCP source is
selected, but a non-HDCP compliant device (e.g., an HDCP
repeater) has been detected. Video output is disabled.
Next Input Format — Indicates the input formats on Program, in the form:
Hact x Vact @ Vr Hz
S 1400x1050@59.94 Hz
DCS-200 • User’s Guide
45
4. Operation
Using the Setup Menu
rëáåÖ=íÜÉ=pÉíìé=jÉåì
After DCS-200 initialization is complete, the Status Menu appears. This is the system’s
top-level menu. Refer to the “Status Menu” section on page 44 for details.
To display the Setup Menu from the Status Menu, press SEL.
Note
When you make changes to input, output and system
parameters, your “configuration” information can be stored in
non-volatile memory — provided that you perform a “Save
Config” operation. In this way, your settings will be recalled
automatically each time the unit is turned on. Note that if the
“Auto Input Save” function is enabled in the User
Preferences Menu, the system automatically saves inputs.
The figure below illustrates the Setup Menu:
SE TUP ME NU
> T r a ns T i m e
Output
Pr eview
Inpu t
Key Setu p
Logo Set up
User Preference
System
Tech Suppo rt
Factory Reset
1.0
>>
>>
>>
>>
>>
>>
>>
>>
Figure 4-9. Setup Menu (sample)
Following are descriptions of each Setup Menu function:
•
•
•
•
•
•
•
•
•
•
46
Trans Time
Output Menu
Preview Menu
Input Menu
Key Setup Menu
LOGO Setup Menu
User Preference
System Menu
Tech Support
Factory Reset
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
qê~åë=qáãÉ
From the Setup Menu, select Trans Time to change the current transition rate that is used
when you mix between inputs, when you transition to/from keys, and when you transition
to/from black.
Following are two illustrations of the transition interval:
•
Standard Mix — When transitioning between inputs and the LOGO, or
transitioning to/from black, the DCS-200 functions as a seamless switcher. The
transition interval is defined as the total time required to mix to the new source, or
fade to/from black.
Video
Mix
Input 1
Input 2
Black
Transition Time
Figure 4-10. Transition interval diagram — mix between sources
•
Mix plus Digital Key — When transitioning to/from a digital key source, the
definition is the same as a standard mix — the total time required to fade to the
new source, plus or minus a key.
Digital Key Source
Video
Mix
Input 1
Input 2
Black
Transition Time
Figure 4-11. Transition interval diagram — mix between sources and a digital key
Note that transition times are specified for switching applications with Auto
Acquire turned OFF. When Auto Acquire is ON, the transition time is greater,
due to the additional time required to analyze the input video timing.
Transition values are listed below:
•
•
Adjustment range: 0.0 - 12.0 seconds (0.0 is a cut)
Default: 1.0 seconds
lìíéìí=jÉåì
From the Setup Menu, select Output to display the Output Menu.
OUTPUT
>
Test Patt ern
Sync Setu p
Gamma
Save Con fig
1024x76 8 @59. 94
>>
>>
1.3
Figure 4-12. Output Menu (sample)
DCS-200 • User’s Guide
47
4. Operation
Using the Setup Menu
Following are descriptions of each Output Menu function:
•
•
•
•
•
Output Format
Test Pattern
Sync Setup
Gamma
Save Output Config
lìíéìí=cçêã~í
From the Output Menu, select the top Output Format line to view or change the current
output format. This line indicates the format in the following form:
Hact x Vact @ Vr Hz
The output format for the DCS-200 can be set to any of the progressive outputs in the
format table. In Appendix A, refer to the “Format Table” section on page 122 for details.
Note
The output format is not updated until SEL is pressed.
qÉëí=m~ííÉêå
From the Output Menu, select Test Pattern to display the Test Patterns Menu:
TE ST P AT TERNS
> Mode
T ype
Ra st er B ox
ON
Bu rst
OFF
Figure 4-13. Test Patterns Menu (sample)
The following functions are available on the menu:
•
•
Mode — This function enables or disables the test pattern generator.
Type — This function enables you to select a test pattern. Available choices are:
~
~
~
~
~
~
~
~
48
H Ramp
V Ramp
100% Col Bars
75% Col bars
16 x 16 Grid
32 x 32 Grid
Burst
~
~
~
~
~
~
~
Gray Steps 1
Gray Steps 2
Red
Green
Blue
White
Black
50% Gray
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
•
Raster Box — This function enables or disables the raster box on the output.
~
When turned ON, the system displays a one-pixel border around the
active output area. Note that the raster box includes gaps that enable
you to precisely align the input video to fill the output raster.
~
When turned OFF, the output is clean, without the border.
póåÅ=pÉíìé
From the Output Menu, select Sync Setup to display the Output Sync Select Menu:
OUTP UT SY NC S ELE CT
> A na l og S y n c
DV I S y nc
-H-V
+H+V
Figure 4-14. Output Sync Select Menu (sample)
The Output Sync Select Menu enables you to independently adjust the output sync
polarity of the Analog and DVI outputs. The following functions are available:
•
Analog Sync — This field sets the analog output sync polarity.
~
~
•
Values: CSync, -H-V, -H+V, +H-V, +H+V
Default: -H-V
DVI Sync — This field sets the DVI output sync polarity.
~
~
Values: -H-V, -H+V, +H-V, +H+V
Default: +H+V
d~ãã~
From the Output Menu, select Gamma to specify the output Gamma.
•
•
Adjustment range: 1.0 to 3.0, in steps of 0.1
Default: 1.0
p~îÉ=lìíéìí=`çåÑáÖ
From the Output Menu, select Save Config to save the current output configuration. A
message is briefly shown, after which the system returns to the Output Menu.
Savin g Output Co nfig
Figure 4-15. Saving Output Configuration Message
DCS-200 • User’s Guide
49
4. Operation
Using the Setup Menu
Please note the following important points regarding the output configuration file:
•
When you perform the Save Config function, all configuration parameters from
the Output Menu are saved in non-volatile memory. If you do not perform the
function, output data will not be restored upon the next system power up.
•
If you make a change in the Output Menu, and attempt to exit the menu (by
pressing ESC) without saving changes, the system displays the following prompt:
Save Output Cfg?
<SEL> = Yes
<ESC> = No
Figure 4-16. Save Output Configuration Prompt
~
~
Select Yes (SEL) to save changes.
Select No (ESC) to continue operation without saving the changes.
mêÉîáÉï=jÉåì
From the Setup Menu, select Preview to configure the DCS-200’s Preview output. The
Preview output allows you to view, resize, and otherwise adjust the input source before
taking it to Program. You can preview each of the input sources (1 through 8, SDI and
LOGO). The input source is scaled to the selectable progressive resolution and output on
the DVI Digital and HD-15 analog VGA connectors.
The following illustration shows the Preview Menu:
PREV IE W
Output Src
Test Patt erns
Sync Setu p
S ave
Program
1024x768@59.94
>>
>>
Figure 4-17. Preview Menu (sample)
Note
50
After you view and adjust a source on the preview monitor,
and press TAKE to bring it to Program, the preview and
Program images exchange positions, or “flip-flop,” as
described in the “Flip-flop Mode” section on page 85. There
is a slight delay in the image exchange between the preview
output and the Program output. The preview image appears
slightly after the Program image.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
The following sections provide detailed information about Preview Menu functions:
• Output Src
• Output Format (Preview)
•Test Patterns (Preview)
• Preview Sync
• Save (Preview)
lìíéìí=pêÅ
In the Preview Menu, choose Output Src to select the source to be displayed on the
preview monitor. The source can be either Preview or Program.
•
•
Choose Preview to display on the preview monitor the “pending” source.
Choose Program to display on the preview monitor the same source that is on
Program.
Important
In Preview mode, when you press KEY to “pend” the key
transition, you will not see the key overlay on the preview
monitor. If you then press TAKE, the input and key appear
on Program.
To see the key on the preview monitor, you can route the
source from Program to preview using the Output Src
selection of the Preview Menu. This selection places a copy
of the Program image on the preview monitor, including the
key. For more information about keys, see the “Using Keys”
section on page 95.
lìíéìí=cçêã~í=EmêÉîáÉïF
In the Preview Menu, the [output_format] field displays the format of the output, in the
following form:
Hact x Vact @ Vr Hz
S 1024x768@59.94
The output format for the DCS-200 can be set to any of the progressive outputs in the
format table. In Appendix A, refer to the “Format Table” section on page 122 for details.
Note
The output format is not updated until you press SEL.
To make pixel-for-pixel adjustments, set the Preview and Program resolutions to be the
same, as shown in the following illustration:
Figure 4-18. Matching Preview and Program Resolutions
If you do not need to make pixel-perfect adjustments to the Preview image, the resolutions
of the Preview and Program outputs do not need to be the same, as shown in the following
DCS-200 • User’s Guide
51
4. Operation
Using the Setup Menu
illustration:
Figure 4-19. Different Preview and Program Resolutions
qÉëí=m~ííÉêåë=EmêÉîáÉïF
In the Preview Menu, the Test Patterns submenu provides the following options:
•
•
Mode enables or disables the test pattern generator. The values are ON and OFF.
Type provides a list of the available test patterns. The choices are:
~
~
~
~
~
~
~
~
•
~
~
~
~
~
~
~
H Ramp
V Ramp
100% Col Bars
75% Col bars
16 x 16 Grid
32 x 32 Grid
Burst
Gray Steps 1
Gray Steps 2
Red
Green
Blue
White
Black
50% Gray
Raster Box — This function enables or disables the raster box on the Preview
output.
~
When turned ON, the system displays a one-pixel border around the
active output area. Note that the raster box includes gaps that enable
you to precisely align the input video to fill the output raster.
~
When turned OFF, the output is clean, without the border.
mêÉîáÉï=póåÅ=
From the Preview Menu, select Sync Setup to independently adjust the output sync
polarity of the analog and DVI outputs of the Preview. The Preview Sync Menu looks like
the one in the following illustration.
PREV IE W SY NC
Analog Sync
DVI Syn c
-H-V
+H+V
Figure 4-20. Preview Sync Setup Menu (sample)
52
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
The selectable values are:
•
Analog Sync — This field sets the analog output sync polarity.
~
~
•
Values: -H-V, -H+V, +H-V, +H+V
Default: -H-V
DVI Sync — This field sets the DVI output sync polarity.
~
~
Values: -H-V, -H+V, +H-V, +H+V
Default: +H+V
p~îÉ=EmêÉîáÉïF
After you make changes using the Preview Menu, use the Save function to store them in
non-volatile memory. Your configuration parameters will then persist across power cycles.
If you do not choose Save after making changes, you are prompted to do so with a
message like the one shown in the following illustration.
S a v e P r e v i e w Co n f i g ?
<SEL> = Yes
<ESC> = No
Figure 4-21. Save Preview Configuration Prompt (sample)
•
•
Press SEL to save your changes.
Press ESC to continue without saving your changes.
If you do not save your changes, your settings will not be restored the next time the system
is powered up or the input is selected.
fåéìí=jÉåì
From the Setup Menu, select Input to display the Input Menu. The Input Menu enables
you to set parameters for the selected input on Program.
Important
DCS-200 • User’s Guide
The Input Menu does not appear in the menu tree when the
LOGO is on Program.
53
4. Operation
Using the Setup Menu
The format of the selected input on Program is shown on the second line.
INPUT
> Adjust On
T ype
Co lorspace
Background
Timing Adjust
Image Adjust
Co ntrast
Brightness
Color Balance
Processing
Re se t Config
Save Con fig
Delete Config
Recall Config
1024x76 8 @59. 94
Pr eview
RGB /H D-Y UV
RGB
Bla ck
>>
>>
100. 0%
100. 0%
>>
>>
>>
>>
>>
Figure 4-22. Input Menu (sample)
The Input Menu can be used in two ways:
•
Press an input button first, TAKE the input to Program, then use the menu to set
input parameters.
•
While you are already in the Input Menu, press a different input button and TAKE
it to Program. The fields update to reflect the values for the new input.
Note
Changing the parameters for one input does not affect the
input configuration of the other inputs.
The following sections provide detailed information about Input Menu functions:
•
•
•
•
•
•
•
•
54
Input Format
Adjust On
Type
Colorspace
Background
Timing Adjust
Image Adjust
Contrast
•
•
•
•
•
•
•
•
Brightness
Color Balance
Processing
About Input Configuration Files
Reset Config
Save Config
Delete Config
Recall Config
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
fåéìí=cçêã~í
From the Input Menu, select the top Input Format line to view the “auto-acquired” format
for the selected input, or to change the format. The format is shown in the following form:
Hact x Vact @ Vr Hz
S 1024x768@59.94
Please note the following important points:
•
•
•
If you select an input and it does not have a valid signal, "Invalid Signal" appears.
If an input was previously valid and its signal is lost, the "Invalid Signal" message
appears.
When In Auto Acquire is ON (in the User Preferences Menu), the input video
format for non-digital sources will be detected in the following search order:
~
~
~
The saved file as defined in the File Association Menu
~
A best guess (to the closest video format in the library)
The library of saved configurations for the selected input
Standard library formats as defined in Appendix A, in the “Format Table”
section on page 122
For digital sources, when In Auto Acquire is ON, the search order is:
~
~
~
•
The saved configuration file as defined in the File Association Menu
Your library of saved files
A direct measurement of the signal
If the video format is a “best guess” as determined by the “auto acquire” mode, it
is displayed (only in the Status Menu) within asterisks.
S *1024x768@60.11*
•
If you select an input that has been saved (using the Save Config function), the
video format is displayed (only in the Status Menu) within brackets.
S [1024x768@59.94] This example is a saved “exact match” from the format
table (or library).
S [*1024x768@59.90*] This example is a saved “best guess.”
•
When In Auto Acquire is OFF, the system attempts to lock to the signal using the
configuration defined in the File Association Menu for each input channel. If the
input signal is too different from the saved configuration to be usable, the display
indicates "Invalid Signal."
^Çàìëí=lå
In the Input Menu, the Adjust On field indicates whether any changes you make using the
Input Menu will be applied to the Preview or Program source.
For example, if you select Preview, as shown in the illustration below, and change the
Background, Color Balance, or other parameters using the Input Menu, you can view
DCS-200 • User’s Guide
55
4. Operation
Using the Setup Menu
those changes on the Preview source — while the Program source remains unchanged.
INPUT
1024x76 8 @59. 94
Pr eview
> Adjust On
Figure 4-23. Adjust On Field
If both paths are using the same input source, only the selected path is modified.
When LOGO is the input for the Adjust On selection, all the Input Menu values except
Adjust On are bracketed.
qóéÉ
In the Input Menu, the Type field shows the currently selected input type, and enables you
to change the type if required. The available types depend on the selected input:
•
•
•
•
For inputs 1 - 6: CVBS, Y/C, YPBPR, RGB/HD-YUV
For inputs 7 - 8 (when Digital): DVI
For inputs 7 - 8 (when Analog): CVBS, Y/C, YPBPR, RGB/HD-YUV
For the SDI input: [SDI]
Note
The SDI input always shows its type in brackets (e.g., [SDI]),
given that this input type cannot be changed.
`çäçêëé~ÅÉ
From the Input Menu, select Colorspace to change the color space for the selected input
on Program. Values depend on the selected input. Please note:
•
The default selection for YPbPr or YUV is SMPTE. In Appendix A, refer to the
“Format Table” on page 122 for information on the formats that are RGB, SMPTE
or both. When both formats are listed, the first item in the list is the default.
•
The Colorspace Menu allows selection between these two values when the input
is analog (excluding CVBS, Y/C) or DVI.
•
•
When either the CVBS or Y/C input is selected, only [SMPTE] is shown.
When the following formats are detected as either SD-SDI or HD-SDI, only
[SMPTE] is shown.
~
~
~
~
~
~
~
~
56
NTSC (480i)
PAL (576i)
1280x720p @50
1280x720p @59.94
1280x720p @60
1920x1080p @23.98
1920x1080p @24
~
~
~
~
~
~
~
1920x1080p @29.97
1920x1080p @30
1920x1080sF@23.98
1920x1080sF@24
1920x1080i @50
1920x1080i @59.94
1920x1080i @60
1920x1080p @25
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
_~ÅâÖêçìåÇ
From the Input Menu, select Background to change the system’s background color
between “Black” and “Gray.” This is a global setting.
When set to Gray, you can clearly see the edges of an input, particularly when the input’s
aspect ratio does not match the output’s aspect ratio. Note that the background selection
persists between source changes.
qáãáåÖ=^Çàìëí
From the Input Menu, select Timing Adjust to display the Timing Adjust Menu, which
allows for exact positioning of the input's active area.
TIMING ADJUST
> Aut o Config
Samp lin g
Pha s e A
Pha s e B
H Total
H Positio n
H Active
V Total
V Position
V Active
[1: 1]
[0]
5
2160
496
1600
[1250]
49
1200
Figure 4-24. Timing Adjust Menu (sample)
Note
Timing Adjust Menu settings apply to analog input sources
only, except for NTSC and PAL sources. For digital, NTSC
and PAL sources, refer to the “Image Adjust” section on
page 60.
For DVI digital, NTSC and PAL videos the Timing Adjust Menu is informational only.
Because the individual parameters cannot be adjusted, they are bracketed, as shown in the
following illustration.
TIMING ADJUST
> Aut o Config
Samp lin g
Pha s e A
Pha s e B
H Total
H Positio n
H Active
V Total
V Position
V Active
[1: 1]
[0]
[N/A]
[85 8]
[12 3]
[72 0]
[52 5]
[36 ]
[48 6]
Timing Adjust Menu — DVI Digital, NTSC, PAL (sample
DCS-200 • User’s Guide
57
4. Operation
Using the Setup Menu
For information about adjusting these inputs, refer to the “Image Adjust” section on
page 60.)
Important
The Timing Adjust Menu does not appear in the menu tree if
the analog input is being undersampled for the following
resolutions:
•
•
•
1920x1080p@60 (173.0 MHz)
1920x1200p@60 (193.25 MHz)
2048x1080p@60 (183.75 MHz)
The following functions are available:
•
•
•
Auto Config — This function performs an automatic input configuration on the
analog source on Program. When Auto Config is selected, the DCS-200 finds
the first and last pixel on each edge of the selected input, and ensures (to the best
possible extent) that the entire image is visible. In addition, the system
automatically phases the input to determine the correct sampling phase.
Tip
Ensure that there are non-black pixels around the extreme
edges of your active video, in order for the image to be
properly sized by the Auto Config function. For example,
if you use a Windows desktop with a high luminance
background, the Auto Config function will be accurate. If,
on the other hand, you use a desktop image with a black
border, the image will not be properly sized.
Note
Auto Config applies to analog input sources only. This
function is identical to the Auto Config function in the Image
Adjust Menu.
Sampling — select this function to change the sampling for the selected input.
Available values are: Oversample and 1:1 (default). Please note:
~
When 1:1 Sampling is selected, the system provides pixel-for-pixel
sampling, and generally better image quality.
~
When Oversample is selected, the system performs multiple samples
for every pixel, with a resulting “softer” image.
~
~
Oversample is only available for RGB and YPbPr analog inputs.
All other input types have defined sample clocks that are inherently 1:1.
If the input is set to one of the other types, the value is [1:1].
Phase A, Phase B — These two selections are advanced features which enable
you to adjust the sample phase of the system’s two scalers. Typically, they do not
need to be adjusted. Refer to the “Adjusting Sample Phase” section on page 59
for instructions.
The six “Active Area” values are initially filled in by the Auto Config command, or set to
their default values. You can adjust values for Analog RGB or YPbPr sources only. Digital
and decoded sources show values in brackets.
Please note:
•
58
When sampling is set to 1:1, values are the true timing measurements for the
analog RGB or YPbPr inputs.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
•
When sampling is set to OverSample, values represent the oversampling factor
being used.
For all Horizontal “active area” fields, all units are measured in pixels:
•
H Total — adjusts the total pixel count per line. This value cannot be adjusted if
the input type is DVI / SDI.
•
•
H Position — adjusts the offset of start of active area from H sync.
H Active — sets the size of the active area.
For all Vertical “active area” fields, all unit are measured in lines.
•
V Total — indicates the total line count per frame. This value is measured, and
can never be adjusted. Its value will always be shown in brackets.
•
•
V Position — sets the offset of start of active area from V sync.
V Active — sets the size of the active area.
^ÇàìëíáåÖ=p~ãéäÉ=mÜ~ëÉ
The DCS-200 has two A-to-D converters, which are referred to as A and B in the Timing
Adjust Menu. The sample phase value of each scaler is initially filled in by the Auto
Config command, or set to the default value of 0 (zero). If required, advanced users can
fine-tune the image by adjusting the sample clock phase of each scaler directly — but only
for inputs whose “type” is analog.
•
•
Adjustment range: -16 to 15
Default: 0
„ Use the following steps to adjust sample clock phase of each scaler, for inputs whose
“type” is analog.
1.
From the Input Menu, navigate to the Timing Adjust Menu, and scroll to the
Phase A or Phase B line.
2.
In the Inputs Section, select an input whose “type” is analog.
3.
TAKE the input to Program. The button lights solid.
4.
Pend the same input for the next transition. In this mode, only one button will now
be lit solid, and no buttons will be blinking.
5.
On the Timing Adjust Menu, note that one of the two Phase lines will be
bracketed, and the other will be unbracketed. When you press TAKE, the
brackets will switch positions. The un-bracketed line is the active scaler.
TIMING ADJUST
Samp lin g
> Pha s e A
Pha s e B
1:1
0
[0]
Figure 4-25. Timing Adjust Menu, phase indication of active scaler
6.
On the selected input, put up a Burst pattern. For example, if the source is a
computer, use a program such as DisplayMate® to generate the pattern.
7.
Scroll to the unbracketed Phase line, and press SEL.
8.
Use the Adjust knob to tweak the burst pattern for the maximum visual clarity and
a minimum amount of visual noise, then press SEL to accept the new value.
DCS-200 • User’s Guide
59
4. Operation
Using the Setup Menu
9.
Press TAKE to activate the other scaler.
10. Repeat steps 7 and 8 for the other scaler.
11. Press ESC to return to the Input Menu.
12. Scroll to the Save Config line, and press SEL to save the configuration for the
selected input.
13. Repeat the entire adjustment procedure from step 1, for all remaining inputs
whose “type” is analog — and be sure to save the input configuration each time
you complete an adjustment for a selected input.
fã~ÖÉ=^Çàìëí
From the Input Menu, select Image Adjust to display the Image Adjust Menu. This
menu, shown in the following illustration, enables you to adjust input parameters such as
horizontal and vertical image size, pan and aspect ratio:
I MA G E A D JU S T
> Aut o Config
H Size
V Size
H Pan
V Pan
Aspe ct Ra tio
Re se t A l l
0
0
[0]
[0]
4:3
Figure 4-26. Image Adjust Menu (sample)
Note
It is recommended that you use the Image Adjust Menu only
when you are using DVI, SDI, NTSC or PAL input sources.
For analog input sources (except NTSC and PAL), refer to the
“Timing Adjust” section on page 57.
Select Auto Config to perform an automatic input configuration on an NTSC or PAL
source on Program. The system finds the first and last pixel on each edge, and ensures (to
the best possible extent) that the entire image is visible. In addition, the system
automatically phases the input to determine the correct sampling phase.
Note
The Auto Config selection is only available for analog inputs
(NTSC or PAL). This function is identical to the Auto Config
function in the Timing Adjust Menu.
The Size and Pan functions allow you to size the image, and then position it within the
selected aspect ratio. The full-screen nature of the final output will be maintained.
•
60
Select H Size to size both the left and right edges simultaneously. Values are in
pixels. The output “window” is maintained in both size and aspect ratio.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
•
Select V Size to size both the top and bottom edges simultaneously. Values are
in lines. The output “window” is maintained in both size and aspect ratio.
Note
For both H Size and V Size, the function always cuts into the
visible image, equally on both sides, and never exposes
video outside the source’s active area. As you size, the
DCS-200 scales the input up to fit the selected aspect ratio.
Note
The maximum allowable H/V size is up to 33% of the input's
corresponding active area. For example, for a 1280x1024
input, the maximum H Size is 422 and the maximum V Size
is 336.
•
Select H Pan to pan a “sized” image left and right — within the selected aspect
ratio. Values are in pixels. The value reads [0] if the image has not been sized
horizontally.
•
Select V Pan to pan a “sized” image up and down — within the selected aspect
ratio. Values are in lines. The value reads [0] if the image has not been sized
vertically.
Note
If both H Size and H Pan are greater than 0, and H Size is
adjusted so that it approaches 0, at a calculated limit, H Pan
automatically adjusts itself to approach 0. This same rule
holds true for V Size and V Pan.
The Aspect Ratio function allows you to set a pre-defined or custom ratio for the input.
•
Select Aspect Ratio to adjust the image to one of the following values: 1:1, 3:2,
4:3, 5:4, 16:9, Custom.
•
If Custom is selected, the Ratio line appears:
~
Adjustment range: 0.750 to 3.000. The default value depends on the
last Aspect Ratio selected before Custom was chosen.
~
Note that the DCS-200 displays the input video aspect ratio according to
the input format detected. For example:
S Computer video at 1280x1024@60Hz defaults to 5:4 aspect ratio
S NTSC video defaults to 4:3, HDTV 1080i video defaults to 16:9
`çåíê~ëí
From the Input Menu, select Contrast to change the contrast of the selected input.
•
•
Adjustment range: 75.0% to 125.0%
Default: 100%
_êáÖÜíåÉëë
From the Input Menu, select Brightness to change the brightness of the selected input.
•
•
DCS-200 • User’s Guide
Adjustment range: 75.0% to 125.0%
Default: 100%
61
4. Operation
Using the Setup Menu
`çäçê=_~ä~åÅÉ
From the Input Menu, select Color Balance to display one of two available Color Balance
Menus. The menu that appears depends on the current input’s “type.” Each menu allows
you to adjust the input’s color balance parameters.
•
•
RGB Color Balance Menu
Color Balance Menu
od_=`çäçê=_~ä~åÅÉ=jÉåì
If the current input’s type is set to RGB, the RGB Color Balance Menu appears:
CO L O R B A L A N C E
> Re d Co ntrast
Re d Bright
Grn Contrast
Grn Bright
Blu Con trast
Blu Brig ht
Re se t A l l
0.0 %
0.0 %
0.0 %
0.0 %
0.0 %
0.0 %
Figure 4-27. RGB Color Balance Menu (sample)
Each of the individual contrast and brightness settings operates in conjunction with the
“global” contrast and brightness settings in the Input Menu.
•
•
•
Adjustment range (all values): -25.0% to +25.0%
Default (all values): 0.0%
Select Reset All to set all values back to their default settings.
`çäçê=_~ä~åÅÉ=jÉåì
If the current input’s type is set to Composite, S-video, YPbPr, or SDI, the Color Balance
Menu appears:
CO L O R B A L A N C E
> Sat urat i on
Hu e
Re se t A l l
100
0
Figure 4-28. Color Balance Menu (sample)
Please note:
•
Saturation is measured in percentage.
~
~
•
62
Adjustment range (SDI, YPbPr): 75.0% to 125.0%
Hue is measured in degrees, and is [N/A] for YPbPr inputs.
~
•
Adjustment range (Composite, S-Video): 0% to 150% (100% nominal)
Adjustment range: -90 to +90
Select Reset All to set all values back to their default settings.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
mêçÅÉëëáåÖ
From the Input Menu, select Processing to display the Processing Menu:
PR O CE SS I NG
> Sync Sel
Pulld own Comp
Sync Slice (mV)
Au to
OFF
128
Figure 4-29. Processing Menu (sample)
The following functions are available:
•
Sync Selection — This function applies only to Analog RGB inputs. The
DCS-200 automatically selects the syncs for digital sources, composite, S-video,
and YPbPr inputs. For these inputs, the value field indicates [N/A].
The sync choices are Auto, H/V (horizontal/vertical sync), CSync (composite
sync) and SOG (sync on green).
•
~
In Auto mode, the system finds sync in any of the three possible
sources.
•
If one of the sources is chosen, the system uses only that input
as a sync source.
•
If the system does not find sync at that source, it acts as if it is in
Auto mode.
~
The default selection for Analog RGB inputs is Auto.
Pulldown Compensation — This function only applies to standard video
(component, s-video, composite and SD/HD SDI) inputs. The mode, which
detects the 3:2 film pulldown sequence, should be turned ON to properly process
video derived from film source material.
~
~
•
Adjustment range: OFF, ON
Default: OFF
Sync Slice — This function selects the sync comparator threshold for RGsB
(RGB with Sync on Green) or YPbPr analog component video sources. When
DCS-200 detects Macrovision copy protection on the incoming YPbPr NTSC/PAL
video, the Sync Slice value is automatically repositioned to 60mV to account for
the reduced amplitude sync pulse.
~
~
Adjustment range: 20mV to 280mV, adjustable in steps of 10mV
Default: 160mV
^Äçìí=fåéìí=`çåÑáÖìê~íáçå=cáäÉë
The DCS-200 supports saving up to 64 input configuration files in non-volatile memory,
each of which is available to the nine physical inputs (1 through 8 and SDI).
Input configuration files contain settings that govern everything from pixel resolution to
aspect ratio and color balance — any setting you can view or change using the Input
Menu. By default, an input’s configuration file number is the same as the number of the
input — Input 1 is assigned to configuration file number 1, and so on. You can set, delete,
save, or recall the configuration file for an input. You can associate any number of saved
files to any number of inputs.
When you change the configuration file for an input, the timing in the new configuration file
DCS-200 • User’s Guide
63
4. Operation
Using the Setup Menu
must match the input’s timing. For example, if the input uses NTSC (720 x 480) timing, that
input cannot use a configuration file that uses WXGA (1280 X 768).
When you delete user-defined configuration files, those files are no longer available for use
by any input.
For more information about using input configuration files, refer to the following sections:
•
•
•
•
•
Reset Config
Save Config
Delete Config
Recall Config
File Association Menu
oÉëÉí=`çåÑáÖ
From the Input Menu, select Reset Config to remove all user-entered configuration
settings from the current input on Program, and restore the input’s parameters from the
system’s internal library values. When you select Reset Config, you will be prompted to
reset (SEL) or continue without resetting (ESC).
Note that if the current format was derived as a best guess, those “guess” values are
restored when you press SEL.
Note
Resetting configuration parameters does not change the
configuration file associated with the input — it simply assigns
the restored parameters to the existing configuration file. The
file number shown in the File Association Menu does not
change.
p~îÉ=`çåÑáÖ
After you use the Input Menu to change one or more input settings, you can save the
changes to non-volatile memory by selecting Save Config. You can save the changes to
the current configuration file for the selected input, or to a different file.
„
To save changes to an input’s configuration, use the following procedure:
1.
Select Save Config from the Input Menu. The menu shown in the following
illustration appears:
SA VE CONFIG
> File Number
Save File
24
Figure 4-30. Save Config Menu (sample)
2.
64
Select a value for File Number, or keep the default file number.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
If you save to another configuration file, the File Association Menu is updated to
associate the new file to the current input. For more information about the File
Association Menu, refer to the “File Association Menu” section on page 79.
Important
3.
You can assign a configuration file to more than one input. If
you do so, you must exercise caution when deleting the file,
because it will be deleted for all inputs.
Scroll down to Save File and press SEL.
A confirmation message is briefly displayed, after which the system returns to the
Input Menu.
Savin g Inpu t File
Figure 4-31. Saving Input File message (sample)
If you change a setting in the Input Menu and press ESC without saving changes, your
change will not be restored the next time you select the input or power up the system. The
system displays the following prompt:
Sa ve Input Cf g?
<SEL> = Yes
<ESC> = No
Figure 4-32. Save Input Configuration Prompt (sample)
•
•
Press SEL to save changes.
Press ESC to exit without saving.
aÉäÉíÉ=`çåÑáÖ
From the Input Menu, select Delete Config to delete any saved configuration file. A
deleted configuration file cannot be recalled by any input.
After you delete a configuration file, what happens the next time you select an input that
uses the file depends on whether In Auto Acquire is ON (in the User Preference Menu).
When In Auto Acquire is ON and an input does not have a saved configuration file, the
DCS-200 does a full sync (timing) acquisition on the selected input signal.
When In Auto Acquire is OFF, the system will use the configuration file defined in the File
Association Menu, to the greatest extent possible. If the input does not have a saved
configuration file, the DCS-200 displays the “Invalid Signal” message and the video output
is black.
For more information about In Auto Acquire, refer to the “Understanding Auto Acquire”
section on page 86 and the “In Auto Acquire” section on page 70.
DCS-200 • User’s Guide
65
4. Operation
Using the Setup Menu
„ Use the following procedure to delete a configuration file:
1.
From the Input Menu, select Delete Config. The menu shown in the following
illustration is displayed:
DE LET E C O NF IG
> File Number
De lete F i le
1
Figure 4-33. Delete Config Menu (sample)
The value of File Number is set to the current configuration file for the input. You
can either delete this file, select another saved configuration file and delete it, or
press ESC to continue without deleting.
2.
Select a file to delete. Then, scroll down to Delete File and press SEL.
A confirmation message is briefly displayed, after which the system returns to the
Input Menu:
De leting I nput File
Figure 4-34. Deleting Input Configuration Message (sample)
Important
You can assign a configuration file to more than one input. If
you do so, you must exercise caution when deleting the file,
because it will be deleted for all inputs.
oÉÅ~ää=`çåÑáÖ
From the Input Menu, select Recall Config to restore a configuration file that was
previously associated with the current input. Using the Recall Config Menu shown in the
following illustration, you can change from the current configuration file for the input to any
saved configuration file:
RE CA LL C O NF IG
> File Number
Recall File
41
Figure 4-35. Recall Config Menu (sample)
A number in brackets indicates the only file that is available for recall. If no files are
available, a message will be displayed to indicate that there are no saved files.
66
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
After you select a file number and choose Recall File, press SEL to initiate the recall or
ESC to continue using the current configuration.
When you press SEL, if the input timing matches the timing in the recalled input
configuration file, the input uses the recalled configuration file immediately. The File
Association Menu is also updated to reflect your change.
If the input and configuration file timings do not match and In Auto Acquire is ON, an “auto
acquire” will be performed. For more information about this function, refer to the
“Understanding Auto Acquire” section on page 86.
hÉó=pÉíìé=jÉåì
A luminance key is a video effect in which one video source cuts into a background image.
The "key source" is essentially an electronic hole which is cut into a background image, as
shown in the following illustration. In this illustration, DCS-200 is the key, which cuts into
the background image.
Figure 4-36. Example of a Key
In the DCS-200, the key hole is filled with video from one of the two DVI digital input
sources (inputs 7 and 8). You cannot use an analog input as a key source.
From the Setup Menu, select Key Setup to display the Key Setup Menu, which enables
you to select a digital key source and set key parameters. If Menu Context is ON, the
menu appears automatically when the KEY button is pressed.
KE Y SET UP
> Inpu t
Clip
Gain
Opacity
H Of fset
V Of fset
DVI _ 7
0
1.0 0
1023
0
0
Figure 4-37. Key Setup Menu (sample)
DCS-200 • User’s Guide
67
4. Operation
Using the Setup Menu
Following are descriptions of each Key Setup Menu function:
•
Input Source — This field enables you to select the desired digital key source.
~
~
Note
•
This field is bracketed once the key is on Program.
Adjustment range: 0 to 1023
Default: 0
Gain — This value adjusts the sensitivity of the keyer, enabling you to change the
sharpness of the keyed image. Gain only affects the key hole, as set by the clip.
~
~
•
Default: 7
Clip — This value adjusts the threshold of the video that "cuts" into the
background image. A hole will be cut into the background anywhere that
foreground luminance is greater than the clip level.
~
~
•
Selections: 7, 8
Adjustment range: 0 to 1023.99
Default: 1.00
Opacity — This value adjusts key opacity.
~
~
Adjustment range: 0 (fully opaque) to 1023 (fully transparent)
Default: 1023
•
H Offset — This value adjusts the key source’s horizontal offset (in pixels), if the
key source’s resolution is greater than (or less than) the output resolution.
•
V Offset — This value adjusts the key source’s vertical offset (in pixels), if the key
source’s resolution is greater than (or less than) the output resolution.
Tip
Always select the desired key source and adjust the key
parameters prior to your production. The key must be visible
on Program in order to visually adjust clip, gain and opacity.
Refer to the “Using Keys” section on page 95 for more information on using keys.
68
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
ildl=pÉíìé=jÉåì
A logo is a full-screen video source that, when you transition to it, appears on top of all
other sources. From the Setup Menu, select LOGO Setup to display the LOGO Setup
Menu, which enables you select, save and delete up to three full-screen logos.
LOGO SETUP
Selection
LOGO1
[1024x76 8]
Save Pgm t o Log o
Delete LOGO1
Figure 4-38. LOGO Setup Menu (sample)
Following are descriptions of each Key Setup Menu function:
•
LOGO Selection — This field enables you to select the desired logo.
~
~
•
Selections: LOGO1, LOGO2 and LOGO3
Default: LOGO1
[resolution] — This field shows the current resolution of the saved logo, if the
output resolution matches the resolution at which the logo was captured. The field
shows [EMPTY] if nothing has been saved at the selected location, or [INVALID
[resolution]] — e.g. [INVALID 1600x1200] — if the logo resolution does not
match the current output resolution.
Because the field is not user selectable, all data is shown between brackets.
•
Save Pgm to Logo — Choose this field and press SEL to save the current input
(on Program) to the selected logo memory register. The Save Pgm to Logo field
does not appear if the logo is pending or on Program.
Important
•
If a key is enabled in the input source, the key becomes part
of the stored logo and transitions to Program when you press
TAKE.
Delete LOGO — Choose this field and press SEL to delete the logo from the
selected memory register. The Delete LOGO field does not appear if the logo is
pending or on Program.
Refer to the “Using the LOGO” section on page 88 for more information on using logos.
DCS-200 • User’s Guide
69
4. Operation
Using the Setup Menu
rëÉê=mêÉÑÉêÉåÅÉ
From the Setup Menu, select User Preference to display the User Preference Menu:
US ER P RE FERENCE
> In Auto Acquire
Aut o Inp ut Cfg.
Aut o Inp ut Save
Black Auto Take
Key Auto Take
Menu Context
ON
OFF
ON
OFF
OFF
OFF
Figure 4-39. User Preference Menu (sample)
The following functions are available:
•
•
•
•
•
•
•
In Auto Acquire
Auto Input Config
Auto Input Save
Auto Take
Black Auto Take
Key Auto Take
Menu Context
få=^ìíç=^ÅèìáêÉ
The In Auto Acquire function enables or disables the Input Auto Acquire mode, which
acquires a signal for the input. Values for In Auto Acquire are: OFF and ON (default).
When In Auto Acquire is ON, and an input has a saved configuration file, the system
attempts to use the saved file. If the input timing matches the timing in the saved
configuration file, the saved file is used.
The system always performs a full sync (timing) acquisition on the selected input signal
under the following conditions:
•
•
•
•
When an input without a saved configuration file is selected
When the input type is changed
When the input signal’s sync rate is changed
When an input with a saved configuration file is selected, but the input timing is
different from the saved configuration
When In Auto Acquire is ON, and the input source is non-digital, the system uses the
following library search order:
70
•
Saved configuration files defined in the File Association Menu for each input
channel
•
•
The user’s library of saved files
•
A best guess
The standard Input Format table defined in Appendix A, in the “Format Table”
section on page 122
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
When In Auto Acquire is ON, and the input source is digital, the system uses the following
search order:
•
Saved configuration files defined in the File Association Menu for each input
channel
•
•
The user’s library of saved files
Direct measurement of the signal
If the input signal’s timing is too different from the saved configuration, a good lock may not
be possible. In this situation, the "Invalid Signal" message is displayed, and the video
output will be black. You will also see "Invalid Signal" if the configuration file for an input
has been deleted.
Note
When you turn In Auto Acquire ON, the DCS-200
automatically turns Auto Input Config and Auto Input Save
ON as well. Similarly, if you turn In Auto Acquire OFF, Auto
Input Config and Auto Input Save turn OFF as well. If you
wish to adjust these fields independently, you can still do so.
Please note the following important points:
•
It is recommended that you leave the In Auto Acquire mode ON. Then, if the
timing changes on any input (whether or not you have a saved config file), you will
always get an output image. On the other hand, if the mode is OFF and the input
timing changes, the output will be black.
•
When the In Auto Acquire mode is ON, the DCS-200 automatically detects and
acquires the input video type and resolution (in most cases), and limits menu
selections to those applicable to the detected video type.
•
If you are an advanced user and you know the exact timing parameters for your
input(s), you can turn the In Auto Acquire mode OFF, and dial in your timing
parameters manually.
Tip
If you have already saved configuration files for your inputs, it
is recommended that you turn the In Auto Acquire mode
OFF. This provides the fastest transition times. When the
mode is ON, transition times will be greater, due to the time
required to analyze the input timing for each source.
^ìíç=fåéìí=`çåÑáÖ
The Auto Input Config function enables or disables the automatic input configuration
mode. Values are: OFF and ON (default).
DCS-200 • User’s Guide
Note
This is the “automatic” version of the manual Auto Config
mode, which is located in both the Image Adjust Menu, and
the Timing Adjust Menu. Refer to the “Timing Adjust”
section on page 57 for details.
Note
The In Auto Acquire mode must be ON, in order for the Auto
Input Cfg mode to function. If In Auto Acquire is OFF, the
Auto Input Cfg mode is bracketed.
71
4. Operation
Using the Setup Menu
•
When ON, the system automatically finds the first and last pixel on each edge of
the selected input, and ensures (to the best possible extent) that the entire image
is visible. In addition, the system automatically phases the input to determine the
correct sampling phase.
These functions will only be performed under the following conditions:
~
~
~
•
When an input without a saved configuration file is selected.
When the input signal changes sync rates.
When an input with a saved configuration file is selected, but the input
timing is different from the saved configuration.
When OFF, the system uses the last known configuration for each input, to the
greatest extent possible.
^ìíç=fåéìí=p~îÉ
When the Auto Input Save mode is enabled, the system automatically saves the selected
input after it has been acquired for the first time. If the In Auto Acquire mode is OFF, the
field has no effect. The default is ON.
^ìíç=q~âÉ
The Auto Take mode allows you to bring an input source to Program by simply pressing an
input button (1 through 8, SDI, or LOGO), and without requiring a Take.
Regardless of your In Auto Acquire settings, the input button you select blinks “fast,” to
indicate that the system is performing an action such as an auto acquire, file association, or
another action. When the system completes its tasks for the input, the button blinks “slow”
to indicate that the input is ready to be taken to Program. Lastly, the button lights solid and
the source goes to Program automatically.
•
When ON, Auto Take overrides user preferences for Black Auto Take and Key
Auto Take. The values for these two menu items are bracketed.
•
When OFF, the selected input button blinks “fast” and then “slow.” Press TAKE to
perform the transition.
_ä~Åâ=^ìíç=q~âÉ
The Black Auto Take function controls the behavior of the BLACK button:
•
When ON, the BLACK button transitions the Program output to/from black, as
soon as the button is pushed.
•
When OFF, the BLACK button blinks when pressed, to indicate “pending.” Press
TAKE to perform a transition to/from black.
Refer to the “Using Black” section on page 93 for details.
hÉó=^ìíç=q~âÉ
The Key Auto Take function controls the behavior of the KEY button:
•
When ON, the KEY button performs a Key Up or Key Down transition, as soon
as the button is pushed.
•
When OFF, the KEY button blinks when pressed, to indicate “pending.” Press
TAKE to perform a Key Up or Key Down.
Refer to the “Using Keys” section on page 95 for details.
72
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
jÉåì=`çåíÉñí
The Menu Context function determines the behavior of certain menus when an Input,
LOGO or KEY button is pressed. The following conditions apply:
•
When ON, regardless of the current menu, the Input Menu, LOGO Menu or Key
Menu will automatically be displayed when the associated button is pressed.
•
When OFF, menu context does not change when an Input, LOGO or KEY button
is pressed.
póëíÉã=jÉåì
From the Setup Menu, select System to display the System Menu, which enables you to
adjust VFD brightness, input configurations, front panel lockout modes, Ethernet
parameters and many other “system” related functions:
SY STE M
> VF D Bright ness
Et hernet
Serial Setup
EDID Se tup
DVI Cable Equal
E xecut i ve M o d e
File Association
Temperature
Dia gnostics
Save System State
10
>>
>>
>>
>>
>>
>>
>>
>>
Figure 4-40. System Menu (sample)
The following sections describe each System Menu function:
•
•
•
•
•
•
•
•
•
•
VFD Brightness
Ethernet
Serial Setup
EDID Setup
DVI Cable Equalization
Executive Lockout Mode
File Association Menu
Temperature
Diagnostics
Save System State
sca=_êáÖÜíåÉëë
From the System Menu, select VFD Brightness to control the intensity of the front panel
VFD (vacuum fluorescent display).
•
DCS-200 • User’s Guide
Adjustment range: 1 - 16 (1 is the dimmest setting)
73
4. Operation
Using the Setup Menu
•
Default: 10
Note
It is recommend that you use a low intensity setting to avoid
"burn-in" of the display.
bíÜÉêåÉí
From the System Menu, select Ethernet to display the Ethernet Menu:
ET HE RN ET
> DH C P
OFF
Co nfig Network
>>
IP
192.168.000.010
M
00:04:a5:19:10:52
Figure 4-41. Ethernet Menu (sample)
The following Ethernet functions are available:
•
DHCP — DHCP can be turned OFF or ON.
~
Note
~
•
When OFF, the Config Network field appears, which enables you to
manually enter a static IP address, Subnet mask and Gateway.
Always consult with your network administrator to obtain valid
IP, subnet mask and gateway addresses.
When ON, the DCS-200 queries the DHCP server for a valid IP address,
and the Config Network field is hidden.
•
If the DCS-200 finds a DHCP server and receives an IP
address, the address is displayed.
•
If a server is not found, an IP address is not assigned.
Config Network — select this function to display the Config Network Menu,
which enables you to choose the specific Ethernet address you wish to change.
CO N F I G N E T W OR K
> Set St atic IP
Set Netmask
Set Gateway
>>
>>
>>
Figure 4-42. Config Network Menu (sample)
74
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
~
Select Set Static IP to display the Static IP Menu, which enables you to
set a static IP address when a DHCP server is not available. The editing
procedure is discussed below.
ST ATIC IP
>
192.168.000.010
Figure 4-43. Static IP Menu (sample)
~
Select Set Netmask to display the Netmask Menu, which enables you
to set a netmask. The editing procedure is discussed below.
Ne tmask
>
255.255.255.000
Figure 4-44. Netmask Menu (sample)
~
Select Set Gateway to display the Gateway Menu, which enables you to
set a gateway. The editing procedure is discussed below.
Gateway
>
192.168.000.002
Figure 4-45. Gateway Menu (sample)
„ Use the following steps to edit the IP address, Netmask or Gateway. Valid
fields range from 000 to 255.
DCS-200 • User’s Guide
a.
Press SEL to begin editing. This action highlights the first digit, and
displays the carat “^.”
b.
Use the ADJUST knob to move the carat left and right through the
address.
c.
When the desired digit is highlighted, press SEL to edit the value. The
carat changes to the pound sign “#.”
d.
Use the ADJUST knob to select the desired value (0 - 9).
e.
Once the value is selected, press SEL to “accept” the new value. The
pound sign “#” changes back to the carat “^.”
f.
Repeat the process from step b for all additional digits that you wish to
change.
g.
When complete, press ESC to display the Apply Changes Menu.
•
Select Yes (SEL) to apply all changes.
•
Select No (ESC) to exit the procedure without saving changes.
75
4. Operation
Using the Setup Menu
In each case, system returns to the root menu.
When Ethernet setup is complete, you can communicate with the DCS-200 via the
Ethernet port.
•
~
In Appendix B, refer to the “Remote Commands” section on page 134
for details on communicating with the DCS-200 via Telnet.
~
In Chapter 5, refer to the “GUI Connection and Launch” section on
page 104 for details on running the web-based GUI.
IP Address — The IP line is an information-only line that shows the current IP
address in all modes (with DHCP on or off). If an IP address has not been
established (no DHCP server found, or the network cable is not connected), the
address reads "000.000.000.000."
Note
•
The DCS-200’s default IP address is 192.168.0.10
MAC Address — The M line is an information-only line that shows the MAC
(hardware) address of the unit's Ethernet port.
pÉêá~ä=pÉíìé
From the System Menu, select Serial Setup to display the Serial Setup Menu, which
enables you to set system RS-232 parameters for the serial port.
SE RI AL S ET UP
> Bau d
Par ameter s
Ha ndshaking
Re se t
1152 00
N81
ON
Figure 4-46. Serial Setup Menu (sample)
The following functions are available:
•
Baud — Use this function to set the baud rate.
~
~
•
Default: 115200
Parameters — This function is a combined setting of Parity, Data Bits and Stop
bits (in this order).
~
~
•
Adjustment range: 9600, 38400, 57600 and 115200
Adjustment range: N81, E71, O71, E72, O72
Default: N81
Handshaking — This function controls the hardware flow of the serial port.
~
~
Adjustment range: ON, OFF
Default: ON
When ON, RTS/CTS and DSR/DTR are used to control the data flow in and out of
the serial port. When OFF, the state of these control lines is ignored.
•
76
Reset — Use this function to reset all serial values to their default settings.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
bafa=pÉíìé
From the System Menu, select EDID Setup to display the EDID Setup Menu, which
enables you to update the preferred EDID (Extended Display Identification Data)
resolution for the DCS-200.
EDID SETUP
> Inpu t
Type (7, 8 )
7
1280x1024 @60
Digital
Figure 4-47. EDID Setup Menu (sample)
Important
This menu is designed for advanced users only. Do not
reprogram EDID unless it is necessary.
EDID is a VESA standard data format that contains information about a display device and
its capabilities, including the preferred (as well as the allowed) device resolutions.
The DCS-200’s EDID file is stored in non-volatile memory. This file is read by a computer's
DVI graphics card during boot-up, when its DVI output is connected to a DVI-I input
connector on the DCS-200 system. The DCS-200 must be powered on first for the EDID
information to be read.
The following functions are available:
•
•
Input — selects the inputs that you wish to program: ALL, 1, 2, 3, 4, 5, 6, 7, or 8.
EDID Format — displays the current EDID format, and enables you to select a
new format to program into memory. Press SEL to program the preferred DVI
resolution, as defined on the EDID Format line.
Note
The DCS-200 can program the EDID EEPROM with the DVI
cable connected.
When SEL is pressed, the following message is briefly displayed.
Programming EDID
Please wait...
Figure 4-48. Programming EDID Message 1
DCS-200 • User’s Guide
77
4. Operation
Using the Setup Menu
If the programming is successful, the following message is displayed:
EDID Prog Done
Connect DVI inpu ts
and reboo t the PC
ES C = Con tinue
Figure 4-49. Programming EDID Message 2
Note
At this point, reboot the external computer(s) in order for the
new EDID information to be read, and the new preferred
resolution to become available.
If the EDID programming failed, the following message will be displayed:
EDID Prog failed!
ES C = Con tinue
Figure 4-50. EDID Programming Failed Message
If this message persists, please contact customer service for technical support.
•
78
Type (7, 8) — This field applies to inputs 7 and 8 only, allowing you to select
between Digital or Analog EDID for these inputs. Please note:
~
When the Input field is set to inputs 1 - 6, the Type field shows
[ANALOG], and cannot be changed.
~
When the Input field is set to 7 or 8, the Type field is selectable between
ANALOG or DIGITAL, and the current Type is reflected. Changing this
field triggers the programming process as soon as SEL is pressed, using
the currently shown resolution in the Format field.
~
When ALL is selected in the Input field, the Type field reflects Input 7.
Any triggering of the programming process changes both inputs 7 and 8
to the selected option in this field.
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
asf=`~ÄäÉ=bèì~äáò~íáçå
From the System Menu, select DVI Cable Equal to display the DVI Cable Equalizer
Menu, which enables you to adjust input cable equalization parameters for both DVI inputs
simultaneously, or individually for inputs 7 or 8.
DV I CAB LE EQUA LIZ ER
> Inpu t
Equalization
Set to Def aul t
Set to Ma xi m um
Set to Min i mu m
All
12
Figure 4-51. DVI Cable Equalizer Menu (sample)
The following functions are available:
•
Input — selects the exact inputs that you wish to set: ALL (inputs 7 and 8), 7
(individually), or 8 (individually).
Note
•
Inputs 7 or 8 do not need to be selected on the front panel for
this menu to change, and to apply the equalization settings.
Equalization — The equalization adjustment range is from 0 (short cable
equalization) to 15 (long cable equalization). The default value is 12, which
indicates “moderate” equalization.
In general, the default should be adequate for most users, unless cables longer
than 5M are used, and unless your signals are running at high pixel clock rates
(e.g., UXGA).
•
Set to Default — sets the Equalization field to the default setting of 12.
Note
•
•
Equalization is a subjective “visual” adjustment, which
depends on three important factors: cable length, signal
quality and cable quality. If you adjust the equalization,
optimize the setting for the lowest amount of visual artifacts.
Set to Maximum — sets the Equalization field to the maximum setting of 15.
Set to Minimum — sets the Equalization field to the minimum setting of 0.
cáäÉ=^ëëçÅá~íáçå=jÉåì
From the System Menu, select File Association to display the File Association Menu,
which enables you to select or change a configuration file for each of nine physical inputs
(1 through 8 and SDI). The configuration file contains settings that govern everything from
pixel resolution to aspect ratio and color balance — any setting you can change using the
Input Menu. The DCS-200 can store up to 64 input configuration files in non-volatile
memory.
Each time you press an input button, the DCS-200 uses the configuration file associated
with that input. The file is designated by a number from 1 to 64. The default file for each
input is the same as the input number—Input 1 uses configuration file 1, and so on. The
default file for the SDI input is 9.
DCS-200 • User’s Guide
79
4. Operation
Using the Setup Menu
You can view and change the current setting for each input by using the File Association
Menu, shown in the following illustration:
File Association
> Inpu t 1
Inpu t 2
Inpu t 3
Inpu t 4
Inpu t 5
Inpu t 6
Inpu t 7
Inpu t 8
SDI
1
2
3
4
5
6
7
8
9
Figure 4-52. File Association Menu (sample)
When you associate a configuration file with a specific input, the file is used by any input
source connected to that input.
To change a setting, scroll to an input number and press SEL. Choose a new configuration
file and press SEL again. The change takes effect the next time the input button is
pressed.
Refer to the “About Input Configuration Files” section on page 63 for additional
information about setting, recalling, saving and deleting input configuration files.
qÉãéÉê~íìêÉ
From the System Menu, select Temperature to display the System Temperature Menu.
SY STE M T E M PE RA T UR E
Temperature
Temperature
°F 85. 8
°C 29. 9
Figure 4-53. System Temperature Menu (sample)
The System Temperature Menu indicates the chassis’ internal temperature in both celsius
and farenheit. When the menu is displayed, temperature values update every 4 seconds.
Note that the DCS-200 measures the internal temperature for an “over-temp” condition
every 5 minutes. If the system’s internal temperature exceeds 122° F (50° C), the following
message appears:
O VE R T EM PE RA T U RE
Co ntact f actory if
conditio n persist s.
ESC = Continue
Figure 4-54. Over Temperature Warning
80
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
To clear the message and continue operations, press ESC.
Note
This message is a warning only, which does not prevent the
operation of the DCS-200. If this message appears, it is
recommended that you contact Barco Customer Service.
aá~ÖåçëíáÅë
From the System Menu, select Diagnostics to display the Diagnostics Menu:
DI AGNOS TIC S
> SE L = Sta rt T ests
Figure 4-55. Diagnostics Menu
If you suspect a problem with the DCS-200, press SEL to run a series of internal diagnostic
tests. The menu will report back “PASS” or “FAIL.”
Note
If the menu reports “FAIL,” contact Barco Customer Service.
In Appendix C, refer to the “Contact Information” section on
page 160 for contact details.
p~îÉ=póëíÉã=pí~íÉ
From the System Menu, select Save Config to save all current “system” settings so that
they may be restored at power up. A message is briefly shown, after which the DCS-200
returns to the System Menu.
Saving System Config...
Figure 4-56. Saving System Configuration Message
Please note the following important points regarding the system configuration file:
•
When you perform the Save Config function, all configuration parameters from
the System Menu are saved in non-volatile memory. If you do not perform the
function, data will not be restored upon the next system power up sequence.
•
This command also saves the current input as the default power-up selection.
Note
DCS-200 • User’s Guide
If you want the DCS-200 to always power up and acquire an
input other than input 1, perform the Save System State
command while the desired input is selected on Program.
81
4. Operation
Using the Setup Menu
•
If you do not perform the Save System State function, data will not be restored
upon the next system power up sequence.
•
If you make a change in the System Menu and attempt to exit the menu (by
pressing ESC) without saving changes, the system displays the following prompt::
Save System Cfg?
<SEL> = Yes
<ESC> = No
Figure 4-57. Save System Configuration Prompt
~
~
Select Yes (SEL) to save changes.
Select No (ESC) to continue operation without saving the changes.
qÉÅÜ=pìééçêí
From the Setup Menu, select Tech Support to display the Tech Support Menu:
TE CH SUPP ORT
Ver s ion
Pho ne
01. 00
866-374-7878
Figure 4-58. Tech Support Menu
The Tech Support Menu displays the following information:
•
Version — displays the current version of installed operating firmware. This
number changes when you update system software. In Chapter 6, refer to the
“Software Upgrade Overview” section on page 108 for update instructions.
•
Phone — lists the technical support phone number.
c~Åíçêó=oÉëÉí
From the Main Menu, select Factory Reset to display the Factory Reset Menu:
Clear All Saved
C onf ig u ra t io n s?
<SEL> = Yes
<ESC> = No
Figure 4-59. Factory Reset Menu
This function enables you to reset the DCS-200 to its factory default condition, in which all
user-defined input, output and system configuration files are deleted. When the command
is executed, a confirmation menu is shown.
82
DCS-200 • User’s Guide
4. Operation
Using the Setup Menu
•
•
Press SEL to reset the system.
Press ESC to cancel the operation, and return to the Setup Menu.
The following attributes constitute a “factory default” condition:
•
•
•
•
•
•
Input 1 is on Program.
The Output is set to 1024x768@59.94.
The Output Raster Box is OFF.
The Status Menu is displayed.
All menu items are set to their default values (as specified in this chapter).
The serial port is set to the following default values:
~
~
~
DCS-200 • User’s Guide
Baud: 115200
Parameters: N81 (No Parity, 8 Data Bits, 1 Stop Bit)
Handshaking: OFF
83
4. Operation
Using Inputs
rëáåÖ=fåéìíë
This section provides background information and instructions for using inputs. The
following topics are discussed:
•
•
•
•
Input Selection Rules
Flip-flop Mode
Understanding Auto Acquire
Using HDCP
fåéìí=pÉäÉÅíáçå=oìäÉë
„ To transition an input to Program:
1.
Select the desired input in the Inputs Section. Once a button is pressed, it blinks,
indicating that the source is “pending.”
2.
Press TAKE to transition the input to Program, using the current transition rate (as
entered on the Setup Menu).
Note
Whenever TAKE is pressed, the DCS-200 flip-flops sources
in the Inputs Section. Refer to the “Flip-flop Mode” section
on page 85 for additional information.
Please note the following important points:
•
All input buttons are selectable, whether or not they are physically connected, and
whether or not they have valid signals.
~
~
Note
When a button is blinking slow, it is ready to be transitioned to Program.
If an input button is blinking slow and the Status Menu shows
“Invalid Signal,” the system has attempted to acquire the
source, but has failed.
•
If you do not want to pend a source (which may be desirable in some situations),
simply press the blinking source button. It turns off, leaving only the button for the
source on Program lit solid. If TAKE is pressed, no transition will occur.
•
When the Status Menu is on and you select an input, one of two actions occur:
•
~
The Input Menu automatically appears if Menu Context is ON (in the
User Preference Menu).
~
The Status Menu remains on display if Menu Context is OFF.
The “Invalid Signal” message appears under the following conditions:
~
~
~
84
When a button is blinking fast, it is being acquired by the system.
If you select an input, and it does not have a valid signal.
If an input was previously valid and its signal is lost.
If the current “user-selected” format does not match the detected input
signal for the selected input.
DCS-200 • User’s Guide
4. Operation
Using Inputs
•
For information about using the system in conjunction with HDCP inputs, refer to
the “Using HDCP” section on page 86.
cäáéJÑäçé=jçÇÉ
Whenever you press TAKE to mix between inputs (including the LOGO), the DCS-200
automatically flip-flops inputs. Two actions occur when TAKE is pressed:
•
The blinking “next” source transitions to Program. Once it is fully on Program, the
button lights solid.
•
The previous (solid) source on Program automatically becomes the pending
“next” source, and the button blinks.
Program
(solid)
1
2
Pending
(blinking)
3
4
Inputs
5
6
7
8
SDI
LOGO
7
8
SDI
LOGO
Sources before TAKE
Pending
(blinking)
1
2
Program
(solid)
3
4
Inputs
5
6
Sources after TAKE
Figure 4-60. Flip-flop mode, before and after TAKE
Repeatedly pressing TAKE continues to flip-flop the current and pending sources in this
manner. Please note:
•
If Black Auto Take is OFF (in the User Preference Menu), you must press
TAKE to transition to black. If a source is pending, the source flip-flops to
Program — after the system is fully in black.
•
If Black Auto Take is ON, simply press BLACK to transition to black. If a source
is pending, it remains pending after the transition. There is no flip-flop.
•
If Key Auto Take is OFF (in the User Preference Menu), you must press TAKE
to transition the key up or down. If a source is pending, you will transition to the
new source and add the key, and the new source flip-flops to Program.
•
If Key Auto Take is ON, simply press KEY to transition the key up or down. If a
source is pending, it remains pending after the transition. There is no flip-flop.
DCS-200 • User’s Guide
85
4. Operation
Using Inputs
råÇÉêëí~åÇáåÖ=^ìíç=^ÅèìáêÉ
Please note the following important points regarding the In Auto Acquire mode:
•
If In Auto Acquire is ON and a valid input is selected that does not have a saved
Input Config File associated with it, the system attempts to acquire the source
and save an Input Config file. This process may take a few moments.
Note
The Input Config file will only be saved if the "Auto Input
Save" mode is ON in the User Preference Menu.
•
If an input is selected that does have a saved Input Config File associated with it,
the (blinking) source will transition to program after TAKE is pressed.
•
When the system performs an Auto Acquire for Inputs 7 or 8, the DCS-200 first
checks for a DVI signal. If not found, the system looks for a valid analog signal.
•
If In Auto Acquire is OFF and a valid input is selected (either with or without a
saved Input Config file), the system compares the library file to the input’s
incoming timing.
~
If the timings match, the system transitions to the input after TAKE is
pressed.
~
If the timings do not match, the “Invalid Signal” message appears, and
the system transitions to black after TAKE is pressed.
rëáåÖ=ea`m
Note
As a prerequisite, ensure that you have read the “A Word
About HDCP” section in Chapter 1 on page 17 prior to
reading this section.
With DCS-200, the HDCP mode is essentially automatic. Provided that you connect an
HDCP compliant monitor, you can select and switch between unprotected sources and
“protected” HDCP sources (e.g., a Blu-Ray player) without restriction.
•
•
•
Inputs 1 - 6 (analog) are unprotected sources.
Inputs 7 and 8 (analog) are unprotected sources.
Inputs 7 and 8 (digital) are protected when an HDCP source is connected.
Please note the following important points regarding HDCP operations:
•
When the input signal is an HDCP source on DVI inputs 7 or 8, the following
message appears if a non HDCP-compliant monitor is connected:
Selection Not Allowed
Output Display does
n ot s u p p o r t H D C P
Figure 4-61. Error Message: HDCP Not Supported
86
DCS-200 • User’s Guide
4. Operation
Using Inputs
•
DCS-200 • User’s Guide
When the input signal is an HDCP source on DVI inputs 7 or 8 and a valid HDCP
monitor is connected, the following actions occur:
~
~
The DCS-200’s analog output is disabled.
~
You cannot use the FRZ button.
You cannot store a LOGO from a “protected” source. However,
“unprotected” LOGOs that are already stored in the system can be
switched to Program.
87
4. Operation
Using the LOGO
rëáåÖ=íÜÉ=ildl
A logo is a full-screen video source which, when transitioned to Program, appears on top
of all other sources. The DCS-200 can store up to three logos in non-volatile memory.
The DCS-200 enables you to transition to or from a full-screen logo, in the same way that
you transition to or from video inputs. When you press TAKE, the system transitions the
selected logo to or from Program at the current transition rate, and the sources flip-flop in
the manner described in the “Flip-flop Mode” section on page 85.
Please note the following important points:
•
Video
If a source and a key are already on Program, both will dissolve out as the logo
dissolves in. The figure below illustrates this transition:
Digital Key Source
Mix
Input 1
LOGO
Black
Transition Time
Figure 4-62. Transition to LOGO from Source Plus Key
•
If a key is enabled in the input source, and you save the source as a logo, the key
becomes part of the stored logo.
•
A logo will be labeled INVALID if it was captured at a resolution that does not
match the current output resolution The resolution at which it was captured will
also be displayed — e.g., [INVALID 1600x1200].
•
If you scroll to an invalid logo, the LOGO button cannot be activated. The
following message will appear.
This stored LOGO does
no t match the current
output resolu tion.
P l e ase c a p t u r e a g a in .
Figure 4-63. LOGO Output Resolution Message (sample)
•
If LOGO is selected when there are no saved or valid logos, the following
message will appear:
No saved or valid
logos a va ilable
for display
Figure 4-64. LOGO Error Message (sample)
88
DCS-200 • User’s Guide
4. Operation
Using the LOGO
•
When you first start up a DCS-200 that has stored logos, a message like the one
in the following illustration appears during initialization:
LOGO1 loading. ..
5%
Figure 4-65. LOGO Initialization Message (sample)
Ensure that you are familiar with the LOGO Setup Menu. Refer to the “LOGO Setup
Menu” section on page 69 for details.
p~îáåÖ=~=içÖç
„ Use the following steps to capture and store a logo:
LOGO
1.
To capture and store a full-screen logo, first select the input that you wish to store,
and transition it to Program with a TAKE.
2.
From the Setup Menu, select LOGO Setup to display the LOGO Setup Menu.
LOGO SETUP
> Selection
LOGO1
[EMPTY]
Save Pgm t o Log o
Figure 4-66. LOGO Setup Menu (sample)
3.
In the Selection field, press SEL and choose the “register” into which you want to
save the LOGO (e.g., LOGO1, LOGO2 or LOGO3). Press SEL again.
4.
Scroll to the Save Pgm to Logo field, and press SEL to save the input as a fullscreen logo.
Note
5.
Repeat steps 1 through 4 to save up to two additional logos.
Important
DCS-200 • User’s Guide
When a logo is pending or already on Program, the Save
Pgm to Logo field does not appear.
When a “protected” HDCP source is selected (inputs 7 or 8),
and an HDCP compliant monitor is connected to the output,
you cannot save a logo.
89
4. Operation
Using the LOGO
qê~åëáíáçåáåÖ=íç=~=içÖç
„ To transition from the source on Program to a saved logo:
1.
With an output source on Program, press the LOGO button. Please note:
~
If Menu Context is ON (in the User Preference Menu), the LOGO
Setup Menu automatically appears when the LOGO button is pressed.
~
If Menu Context is OFF, the Status Menu (or the current menu)
remains on when the LOGO button is pressed.
The LOGO button blinks “slow” to indicate that a logo is pending, and the LOGO
Setup Menu appears:
LOGO SETUP
> Selection
LOGO1
[ 1024x768]
Figure 4-67. LOGO Setup Menu — Selecting a Logo
2.
Press SEL and scroll to select a saved logo.
Logos appear in this list only if their resolution matches the output resolution.
3.
Press TAKE.
The logo appears on Program and the LOGO Setup Menu displays the logo
number in brackets, as shown in the following illustration:
LOGO SETUP
> Selection
[LOGO3]
[1024x7 68]
Figure 4-68. LOGO Setup Menu — Logo on Program
Note
When the system transitions to the logo, the DCS-200 flipflops sources in the Inputs Section. Refer to the “Flip-flop
Mode” section on page 85 for additional information.
aÉäÉíáåÖ=~=içÖç
„ Use the following procedure to delete a saved logo:
1.
In the LOGO Setup Menu, scroll to Selection and press SEL.
2.
Select the logo to delete. Press SEL.
The DELETE LOGO line displays the logo number you selected.
90
DCS-200 • User’s Guide
4. Operation
Using the LOGO
3.
Scroll to DELETE LOGO and press SEL. A message like the one in the following
illustration appears:
Permanen tly De lete
LOGO2?
<SEL >=YES
<ESC>= NO
Figure 4-69. Delete LOGO Message (sample)
4.
DCS-200 • User’s Guide
Press SEL to delete the logo, or ESC to continue without deleting.
91
4. Operation
Using Freeze
rëáåÖ=cêÉÉòÉ
You can use the FRZ (Freeze) button to create a still image from a video image, typically
for use as a full-screen logo.
„ Use the following steps to freeze and un-freeze an input:
FRZ
1.
Select the desired input and transition it to program with a TAKE.
2.
Press FRZ to immediately freeze the source. The button lights.
3.
To un-freeze the source, press FRZ again. The light turns off.
Important
92
When a “protected” HDCP source is selected (inputs 7 or 8),
and an HDCP compliant monitor is connected to the output,
you cannot use the FRZ button.
DCS-200 • User’s Guide
4. Operation
Using Black
rëáåÖ=_ä~Åâ
BLACK
The BLACK button is used to transition the system’s output to/from black, no matter what
combination of sources are currently on Program. For example:
•
If a single source is on Program (e.g., Input 1), the system will mix to black at the
current transition rate.
•
If multiple sources are on Program (e.g., Input 1 + Key), the system will mix all
sources to Black at the current transition rate.
When BLACK is pressed, one of two different actions can occur, depending on how the
“Black Auto Take” function is set in the User Preference Menu.
•
•
Black Auto Take Off
Black Auto Take On
Note
Refer to the “User Preference” section on page 70 for details
on setting parameters in the User Preference Menu.
_ä~Åâ=^ìíç=q~âÉ=lÑÑ==
When the “Black Auto Take” function is OFF in the User Preference Menu, you must use
the TAKE button to transition to/from black.
„ Use the following steps to transition to/from black, when Black Auto Take is OFF:
1.
Press BLACK. The button blinks to indicate that a transition to/from black is
pending.
2.
Press TAKE. The system transitions to/from black, at the current transition rate.
Please note:
~
If the transition is “to” black, the BLACK button lights solid when black is
fully on Program.
~
If the transition is “from” black, the BLACK button automatically turns off
when the selected source is fully on Program.
Important
DCS-200 • User’s Guide
When the Black Auto Take function is OFF, if a source is
pending when TAKE is pressed, that source transitions to
Program after black is fully reached, and sources flip-flop in
the normal manner. If you do not want to transition to a new
source, simply press the blinking source to “un-pend” it.
93
4. Operation
Using Black
_ä~Åâ=^ìíç=q~âÉ=lå=
When the “Black Auto Take” function is ON in the User Preference Menu, you do not
need to press TAKE to perform a transition to/from black. The transition occurs
immediately, once BLACK is pressed.
„ Use the following steps to transition to/from black, when Black Auto Take is ON:
1.
Press BLACK. The system immediately transitions to/from black, at the current
transition rate.
Please note:
~
If the transition is “to” black, the BLACK button blinks fast during the
transition interval, then lights solid when black is on Program.
~
If the transition is “from” black, the BLACK button blinks fast during the
transition interval, then automatically turns off when the selected source
is fully on Program.
Important
94
When the Black Auto Take function is ON, if a different
source is pending when TAKE is pressed, that source
remains pending (blinking) after black is fully reached. The
system does not transition to the pending source, and
sources do not flip-flop. If desired, you can transition to the
pending source underneath black, by pressing TAKE in the
normal manner, and then pressing BLACK to immediately
fade up to the new source.
DCS-200 • User’s Guide
4. Operation
Using Keys
rëáåÖ=hÉóë
The following topics are discussed in this section:
KEY
•
•
•
Introduction to Keying
Performing a Key
Key Transition Combinations
fåíêçÇìÅíáçå=íç=hÉóáåÖ
A key is a video effect in which one video source cuts into a background image. The
DCS-200 enables you to perform a key over any selected source, using either DVI input 7
or 8 as the key source. All key transitions are seamless, at the same rate as the full-screen
source transitions.
Note
You cannot use an analog input as a key source. You cannot
key over the LOGO.
A variety of “key” transitions can be performed:
•
•
•
•
•
•
•
Mix key up, over the selected source
Mix key down, over the selected source
Mix from a source without a key, to a new source + key
Mix from a source + key to another source without a key
Mix between two sources under a key
Fade to black from a source + key
Fade up from black to a source + key
Before you perform a key transition, ensure that the key source is selected on the Key
Setup Menu, and that the key’s clip, gain and opacity have been adjusted. The key must
be transitioned to Program in order to adjust its parameters. See the “Key Setup Menu”
section on page 67 for details.
Important
In Preview mode, when you press KEY to “pend” the key
transition, you will not see the key overlay on the Preview
monitor. If you then press TAKE, the input and key appear
on Program.
To see the key on the Preview monitor, you can route the
source from Program to Preview using the Output Src
selection of the Preview Menu. This selection places a copy
of the Program image on the Preview monitor, including the
key. For more information about this function, refer to the
“Output Src” section on page 51.
Please note:
•
DCS-200 • User’s Guide
The resolution of the digital key source can be the same, greater than or less than
the system’s selected output resolution.
95
4. Operation
Using Keys
~
If the key source resolution is greater than the output resolution, the
DCS-200 only displays an area equal to the output resolution. This area
can be positioned using the H Offset and V Offset fields on the Key
Setup Menu.
~
If the key source resolution is less than the output resolution, the key is
centered in the middle of the screen. H Offset and V Offset can be used
to position the key within the output active space.
Tip
Select the key source and adjust key parameters prior to your
production. The key must be visible on Program in order to
visually adjust clip, gain and opacity. Refer to the “Key Setup
Menu” section on page 67 for details.
mÉêÑçêãáåÖ=~=hÉó
When the KEY button is pressed, one of two different actions can occur, depending on how
the “Key Auto Take” function is set in the User Preference Menu.
•
•
Key Auto Take Off
Key Auto Take On
Note
Refer to the “User Preference” section on page 70 for details
on setting parameters in the User Preference Menu.
hÉó=^ìíç=q~âÉ=lÑÑ
When the “Key Auto Take” function is OFF in the User Preference Menu, you must use
the TAKE button to perform a “key” transition.
„ Use the following steps to mix a key up or down, when Key Auto Take is OFF:
1.
Press KEY. The button blinks to indicate that a “key’ transition is pending. If
Menu Context is ON, the Key Setup Menu appears, enabling you to change the
key source or adjust key properties.
2.
Press TAKE. The system mixes the key up or down, at the current transition rate.
Please note:
~
If the transition is a “key up,” the KEY button lights solid when the key is
fully on Program.
~
If the transition is a “key down,” the KEY button automatically turns off
when the key is fully off of Program.
Important
~
96
When Key Auto Take is OFF, if a source is pending, you will
transition to the new source and add (or remove) the key
when TAKE is pressed. Sources will flip-flop. If you do not
want to transition to a new source, simply press the blinking
source button to “un-pend” it.
Refer to the “Key Transition Combinations” section on page 97 for
descriptions of the many key combinations that can be performed with
the DCS-200.
DCS-200 • User’s Guide
4. Operation
Using Keys
hÉó=^ìíç=q~âÉ=lå
When the “Key Auto Take” function is ON in the User Preference Menu, you do not need
to press TAKE to perform a key transition. The transition occurs immediately, once the
KEY button is pressed. In addition, if a source is pending, it remains pending after the
transition. There is no flip-flop.
„ Use the following steps to mix a key up or down, when Key Auto Take is ON:
1.
Press KEY. The system immediately mixes the key up or down, at the current
transition rate. Please note:
~
If the transition is a “key up,” the KEY button blinks fast during the
transition interval, then lights solid when the key is fully on Program.
~
If the transition is a “key down,” the KEY button blinks fast during the
transition, then automatically turns off when the key is off Program.
Note
If Menu Context is ON, the Key Setup Menu appears when
you press KEY, enabling you to change the key source or
adjust properties. However, because Key Auto Take is ON,
parameters cannot be adjusted until the transition is over.
Refer to the “Key Transition Combinations” section on page 97 for descriptions of the
many key combinations that can be performed with the DCS-200.
hÉó=qê~åëáíáçå=`çãÄáå~íáçåë
In this section, brief instructions are provided for each individual key transition. Please
remember the following points:
•
If Menu Context is ON, the Key Setup Menu appears when the KEY button is
pressed.
•
Key Clip, Gain, Opacity, H offset and V offset can only be adjusted when the
key is visible on Program. The Key Input field, however, can only be changed
when the key is off Program. Once the key is on, the Input field is bracketed.
•
Whenever TAKE is pressed, the current Program source and the pending
program source will flip-flop. If you do not want to transition to a new source,
simply press the blinking source button to “un-pend” it.
The following combinations are described:
•
•
•
•
•
•
•
DCS-200 • User’s Guide
Mix Key Up
Mix Key Down
Mix Source plus Key Up
Mix Source plus Key Down
Source Transition Under Key
Fade to Black from Source plus Key
Fade up from Black to Source plus Key
97
4. Operation
Using Keys
jáñ=hÉó=ré
„ Use the following steps to mix a key up, over a selected source:
Initial system state: Key is OFF Program
Key Auto Take: ON
Video
Source 1
Key Source
Black
Trans Time
Figure 4-70. Mix Key Up
1.
Select the desired “background” source, and transition it to program with a TAKE.
2.
Press KEY to mix the key up.
jáñ=hÉó=açïå
„ Use the following steps to mix a key down:
Initial system state: Key is ON Program
Key Auto Take: ON
Source 1
Video
Key Source
Black
Trans Time
Figure 4-71. Mix Key Down
1.
Press KEY to mix the key down.
jáñ=pçìêÅÉ=éäìë=hÉó=ré
„ Use the following steps to transition to a new source, and mix a key up:
Initial system state: Key is OFF Program
Key Auto Take: OFF
Video
Source 1
Source 2
Key Source
Black
Trans Time
Figure 4-72. Mix Source plus Key Up
98
1.
Select the source that you want to be the next background. The button blinks.
2.
Press KEY. The button blinks to indicate “pending.”
3.
Press TAKE to transition to the new source and mix the key up.
DCS-200 • User’s Guide
4. Operation
Using Keys
jáñ=pçìêÅÉ=éäìë=hÉó=açïå
„ Use the following steps to transition to a new source, and mix a key down:
Initial system state: Key is ON Program
Key Auto Take: OFF
Video
Source 2
Source 1
Key Source
Black
Trans Time
Figure 4-73. Mix Source plus Key Down
1.
Select the source that you want to be the next background. The button blinks.
2.
Press KEY. The button blinks to indicate “pending.”
3.
Press TAKE to transition to the new source and mix the key down.
pçìêÅÉ=qê~åëáíáçå=råÇÉê=hÉó
„ Use the following steps to transition between sources under a key:
Initial system state: Key is ON Program
Key Auto Take: ON or OFF
Video
Source 1
Source 2
Key Source
Black
Trans Time
Figure 4-74. Transition Sources under Key
1.
Select the source that you want to be the next background. The button blinks.
2.
Press TAKE to transition to the new source underneath the key.
DCS-200 • User’s Guide
99
4. Operation
Using Keys
c~ÇÉ=íç=_ä~Åâ=Ñêçã=pçìêÅÉ=éäìë=hÉó
„ Use the following step to fade both the source and a key to black:
Initial system state: Key is ON Program
Key Auto Take: ON or OFF
Black Auto Take: ON
Video
Source 1
Key Source
Black
Trans Time
Figure 4-75. Transition Source plus Key to Black
1.
Press BLACK to transition both the key and the source to black.
c~ÇÉ=ìé=Ñêçã=_ä~Åâ=íç=pçìêÅÉ=éäìë=hÉó
„ Use the following steps to transition up from black to a source plus a key:
Initial system state: Key is OFF Program
Key Auto Take: OFF
Black Auto Take: OFF
Source 1
Video
Key Source
Black
Trans Time
Figure 4-76. Transition from Black to Source plus Key
100
1.
Pend a new source for the next background. The button blinks.
2.
Press BLACK. The button blinks to indicate “pending.”
3.
Press KEY. The button blinks to indicate “pending.”
4.
Press TAKE to transition both the key and the source up from black.
DCS-200 • User’s Guide
4. Operation
Understanding Front-Panel Lockout
råÇÉêëí~åÇáåÖ=cêçåíJm~åÉä=içÅâçìí
The DCS-200 includes two front-panel lockout modes:
•
•
Full lockout mode, which locks the front panel from all source selections
Executive mode, which locks all front panel selections except the nine input
buttons (1 through 8 and SDI) and LOGO. In executive mode, the user can
transition from one input source to another without pressing TAKE.
cìää=içÅâçìí=jçÇÉ
In the full lockout mode:
•
•
•
All button pushes and all turns of the rotary knobs will be ignored.
All Ethernet and serial communications commands will function normally.
All button lights will continue to reflect the proper state of the inputs.
„ Use the following steps to fully lock and unlock the front panel:
1.
Press and hold the SEL and ESC buttons simultaneously for 3 seconds. Once
this button combination has been detected, the following display appears:
Fro nt Panel
L oc k o u t E n a b l e d
Figure 4-77. System Message: Lockout Enabled
2.
To disable the front panel full lockout mode, press and hold the SEL and ESC
buttons simultaneously for 3 seconds. When the button combination is detected,
the system returns to the menu that was displayed before full lockout mode was
enabled.
bñÉÅìíáîÉ=içÅâçìí=jçÇÉ
From the System Menu, select Executive Mode to initiate a limited front-panel lockout.
Executive mode enables seamless transitions between input sources without the need to
press TAKE. In executive lockout mode:
•
Button pushes will be ignored for all buttons except the nine input buttons and
LOGO. All turns of the rotary knobs will be ignored.
•
To take an input source to Program, press the input or LOGO button without
pressing TAKE. The transition is seamless, even if you have Auto Take (in the
User Preference Menu) turned off.
•
•
All Ethernet and serial communications commands will function normally.
DCS-200 • User’s Guide
All button lights will continue to reflect the proper state of the inputs.
101
4. Operation
Understanding Front-Panel Lockout
„ Use the following steps to enable and disable executive lockout mode:
1.
From the Setup Menu, choose the System Menu.
2.
Select Executive Mode. The following submenu appears:
EX ECUT IVE MODE
<SEL> = Enable
<ESC> = Cance l
Figure 4-78. Executive Mode Menu (sample)
3.
Press SEL. The confirmation message shown in the following illustration appears:
Executive Mode
Ena bled
Figure 4-79. Executive Mode Confirmation Message
4.
Press an input button or LOGO.
The button will blink “fast” to indicate that the system is performing an action such
as an auto acquire, file association, or another action. When the system
completes its tasks for the input, the button blinks “slow” to indicate that the input
is ready to be taken to Program. The input source signal automatically goes to
Program without requiring a Take, regardless of your Auto Take setting.
5.
102
To disable the front panel executive lockout mode, press and hold the SEL and
ESC buttons simultaneously for 3 seconds. When the button combination is
detected, the system returns to the menu that was displayed before executive
lockout mode was enabled.
DCS-200 • User’s Guide
RK==drf=léÉê~íáçåë
få=qÜáë=`Ü~éíÉê
This chapter provides connection, launch and operating instructions for the system’s webbased GUI, which enables you to perform all DCS-200 setup and transition functions, just
like the system’s “physical” front panel.
The following topics are discussed:
•
•
DCS-200 • User’s Guide
GUI Connection and Launch
GUI Operations
103
5. GUI Operations
GUI Connection and Launch
drf=`çååÉÅíáçå=~åÇ=i~ìåÅÜ
„ Use the following steps to connect a PC or laptop, and launch the GUI:
1.
Ensure that your PC (or laptop) uses Windows® 2000 or Windows XP.
2.
Ensure that your PC (or laptop) has a web browser installed, such as Windows
Internet Explorer® or Mozilla Firefox®.
3.
Ensure that your PC (or laptop) uses Java Version 6 or later.
4.
Connect the DCS-200’s Ethernet port to a Switch.
5.
Connect the Switch to your PC (or laptop).
6.
Power-up the DCS-200.
7.
Note the DCS-200’s current IP address:
a.
From the Status Menu, press SEL to display the Setup Menu.
b.
Select System to display the System Menu.
c.
Select Ethernet to display the Ethernet Menu.
d.
Make a note of the information on the IP line, which shows the current IP
address in all modes (with DHCP on or off).
Note
The default IP address is 192.168.0.10.
8.
On your PC (or laptop), open up a web browser.
9.
In the browser’s address bar, enter the DCS-200’s IP address as shown in the
following illustration.
Figure 5-1. Address bar with sample IP address
Note
104
Avoid using leading zeros in the IP address. If your display
panel shows 192.168.000.010, for example, type the address
as shown in the preceding illustration, not as shown on the
display.
DCS-200 • User’s Guide
5. GUI Operations
GUI Connection and Launch
10. When the PC establishes communications with the DCS-200, several web pages
are downloaded into the PC, and the DCS-200 Home Page appears:
Figure 5-2. DCS-200 Home Page
11. Click the Control Application GUI link to launch the GUI. The GUI Status Menu
page appears, as shown below:
Figure 5-3. DCS-200 GUI Status Menu
Note
DCS-200 • User’s Guide
If you cannot see the image shown above, check that you
have the latest version of Java installed on your PC or laptop.
105
5. GUI Operations
GUI Operations
12. The DCS-200 GUI is now ready for use. Refer to the “GUI Operations” section
on page 106 for important operating notes.
If you have trouble establishing communications between
your PC and the DCS-200, in Chapter 6, refer to the
“Troubleshooting Ethernet Communication” section on
page 113 for instructions.
Note
drf=léÉê~íáçåë
The figure below illustrates a sample GUI screen:
Figure 5-4. DCS-200 GUI Setup Menu
Running the DCS-200 GUI is virtually identical to running the system from the physical front
panel. The similarities are:
•
All control panel sections and menus are the same. In Chapter 4, refer to the
“Using the Menu System” section on page 39 for details.
•
All input, transition, and “effect” selection methods are the same. In Chapter 4,
refer to the “Using Inputs” section on page 84 for details.
•
All buttons blink states are the same. In Chapter 4, refer to the “Button States”
section on page 35 for details.
The differences are:
•
•
“Click” instead of press.
Use the Up/Down arrows in place of the ADJUST knob:
~
~
106
Click the Up Arrow to scroll up the menu tree.
Click the Down Arrow to scroll down the menu tree.
•
•
Click “Home” to return to the DCS-200 Home Page, if required.
•
You can not enter or leave the Front Panel Lockout mode from the GUI.
All actions taken on the GUI are mirrored on the physical front panel, and
similarly, all actions taken on the front panel are mirrored on the GUI.
DCS-200 • User’s Guide
SK==réÖê~ÇáåÖ=pçÑíï~êÉ
få=qÜáë=`Ü~éíÉê
This chapter provides detailed instructions for upgrading DCS-200 system software. The
following topics are discussed:
•
•
•
•
•
DCS-200 • User’s Guide
Software Upgrade Overview
Hardware Requirements
Software Requirements
Downloading Software
Ethernet Upgrade Method
107
6. Upgrading Software
Software Upgrade Overview
pçÑíï~êÉ=réÖê~ÇÉ=lîÉêîáÉï
Firmware files for the DCS-200 are loaded into the hardware at power-up. These files are
stored in the unit’s onboard flash memory.
The DCS-200’s system software can be easily upgraded using the following steps:
•
•
•
•
•
Download the appropriate “upgrade” file from the Barco FTP site or website.
Connect a PC (or laptop) to the DCS-200.
Launch a web browser.
Connect to the DCS-200 using its IP address.
Follow the upgrade instructions in the browser.
e~êÇï~êÉ=oÉèìáêÉãÉåíë
The following hardware items are required for upgrading DCS-200 software:
•
•
IBM compatible computer with an available Ethernet port
Local Ethernet network, including an Ethernet switch
pçÑíï~êÉ=oÉèìáêÉãÉåíë
The following list outlines software requirements for upgrading the DCS-200’s software:
•
Ensure that your PC (or laptop) uses the Windows® 2000 or Windows XP
operating systems.
•
Ensure that your PC (or laptop) has a web browser installed, such as Windows
Internet Explorer® or Mozilla Firefox®.
Software files can be downloaded from either the Barco Folsom FTP site or the Barco
website, as described in the following “Downloading Software” section.
108
DCS-200 • User’s Guide
6. Upgrading Software
Downloading Software
açïåäç~ÇáåÖ=pçÑíï~êÉ
Two different methods can be used to download DCS-200 software:
•
•
Via FTP Site
Via Web Site
sá~=cqm=páíÉ
Barco Folsom's FTP site address is: ftp.folsom.com
„ To download software from the FTP site:
1.
Create a target folder on your PC (e.g., DCS-200).
2.
Ensure that your PC is connected to the internet.
3.
Log on to the FTP site using one of the following methods:
a.
If you are using an FTP client such as Ipswitch WS_FTP Professional,
log on to our site as follows:
•
FTP Site: ftp.folsom.com
•
User name: anonymous
•
Password: your email address
S Example: johndoe@somecompany.com
b.
If you are using a web browser, point the browser to:
ftp://ftp.folsom.com
4.
Note
If you are using Internet Explorer 7, after entering the FTP
address, click Page, and then click Open FTP Site in
Windows Explorer.
c.
To use Windows Explorer, right-click the Start button, then click
Explore. When the Explorer window opens, enter the FTP site in the
address bar.
Once logged on, navigate to the following directory:
ftp://ftp.folsom.com/Image Processing/DCS-200/
5.
Transfer the following file to the target folder on your PC:
DCS-200_##_##.tar.gz
6.
Please continue with the “Ethernet Upgrade Method” section on page 110.
sá~=tÉÄ=páíÉ
Barco's web site address is: www.barco.com
„ To download software from the web site:
1.
Create a target folder on your PC (e.g., DCS-200).
2.
Ensure that your PC is connected to the internet.
3.
On the web, navigate to:
DCS-200 • User’s Guide
109
6. Upgrading Software
Ethernet Upgrade Method
http://www.barco.com
4.
Navigate to the “Presentation Systems” home page:
http://www.barco.com/corporate/en/products/
5.
Log in to the Barco Partnerzone.
6.
Navigate to the “Software Updates” link, and download the latest version of code:
DCS-200_##_##.tar.gz
7.
When the File Download Dialog appears, click Save.
8.
When the Save As Dialog appears, navigate to the target folder and click Save.
9.
Please continue with the “Ethernet Upgrade Method” section on page 110.
bíÜÉêåÉí=réÖê~ÇÉ=jÉíÜçÇ
„ Use the following steps to upgrade DCS-200 software:
1.
Ensure that your PC (or laptop) uses the Windows® 2000 or Windows XP
operating systems.
2.
Connect the DCS-200’s Ethernet port to a Switch.
3.
Connect the Switch to your PC (or laptop).
4.
Power-up the DCS-200.
5.
Note the DCS-200’s current IP address:
a.
From the Status Menu, press SEL to display the Setup Menu.
b.
Select System to display the System Menu.
c.
Select Ethernet to display the Ethernet Menu.
d.
Make a note of the information on the IP line, which shows the current IP
address in all modes (with DHCP on or off).
Note
The default IP address is 192.168.0.10.
6.
On your PC (or laptop), open up a web browser.
7.
In the browser’s address bar, enter the DCS-200’s IP address.
Figure 6-1. Address bar with sample IP address
Note
110
Avoid using leading zeros in the IP address. If your display
panel shows 192.168.000.010, for example, type the address
as shown in the preceding illustration, not as shown on the
display.
DCS-200 • User’s Guide
6. Upgrading Software
Ethernet Upgrade Method
8.
When the PC establishes communications with the DCS-200, several web pages
are downloaded into the PC, and the DCS-200 Home Page appears:
Figure 6-2. DCS-200 Home Page
9.
Click the Firmware Upgrade link to continue the upgrade process. The Select
File page appears, as shown below:
Figure 6-3. DCS-200 Select File Page
10. Click the Browse button, and navigate to the folder on your PC where you saved
the latest version of code.
DCS-200 • User’s Guide
111
6. Upgrading Software
Ethernet Upgrade Method
11. In the Upload Dialog, select the file:
DCS200_##_##.tar.gz
... and click Open.
12. In the Select File page, click Start Upgrade.
The Upload Status page appears, which provides status during the upload
procedure:
Figure 6-4. DCS-200 Upload Status Page
13. When the procedure is complete, you have three options:
~
~
Click Home to return to the DCS-200 Home Page.
~
If the upload was successful, click Restart DCS-200 to complete the
entire upgrade procedure.
If a problem was encountered during the process, click View Log File to
display a text-based log of the upload procedure.
14. Close your browser, and resume operations on the DCS-200.
Note
112
Be sure to check the Software Version Menu to verify that
the system has been updated. From the Setup Menu, select
Tech Support to display the Tech Support Menu, which lists
the current software version at the top.
DCS-200 • User’s Guide
6. Upgrading Software
Ethernet Upgrade Method
qêçìÄäÉëÜççíáåÖ=bíÜÉêåÉí=`çããìåáÅ~íáçå
„ Use the following steps to determine the IP address of the DCS-200, and establish
proper communications:
1.
Power-up the DCS-200.
2.
Note the DCS-200’s current IP address:
3.
a.
From the Status Menu, press SEL to display the Setup Menu.
b.
Select System to display the System Menu.
c.
Select Ethernet to display the Ethernet Menu.
d.
Make a note of the information on the IP line, which shows the current IP
address in all modes (with DHCP on or off).
Attempt to ping the DCS-200 as follows:
a.
Connect the DCS-200’s Ethernet port to a Switch.
b.
Connect the Ethernet Switch to your PC.
c.
Turn on the PC or laptop.
d.
Open a command prompt window on the PC. Click Start > Programs >
Accessories > Command Prompt.
e.
On the command prompt line, type:
ping 192.168.0.10
... followed by Enter.
Note
Use the unit’s actual IP address, as determined in step 2
above.
f.
If the computer can successfully communicate with the DCS-200, you
will see a series of “replies” from the target IP address. Repeat the
upgrade procedure as outlined in the “Ethernet Upgrade Method”
section on page 110.
g.
If you see a “Request timed out” message, the PC is unable to locate
the DCS-200. If this is the case:
•
•
•
DCS-200 • User’s Guide
Check your network connections and settings as described
above, or ...
Contact your network administrator, or ...
Contact Technical Support. In Appendix C, refer to the
“Contact Information” section on page 160 for details.
113
6. Upgrading Software
Ethernet Upgrade Method
114
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
få=qÜáë=^ééÉåÇáñ
This appendix provides detailed technical specifications for the DCS-200. The following
topics are discussed:
•
•
•
•
•
•
•
DCS-200 • User’s Guide
Input Specifications
Output Specifications
Physical and Electrical Specifications
Communications Specifications
Agency Specifications
Pinouts
Format Table
115
^K==péÉÅáÑáÅ~íáçåë
Input Specifications
fåéìí=péÉÅáÑáÅ~íáçåë=
The table below lists DCS-200 input specifications.
Table A-1. DCS-200 Input Specifications
Parameter
Inputs 1 - 6
Detail
Specification
Connector
HD-15 VGA
Format
RGBHV / RGBS / RGsB computer video, YPbPr video
(SD or HD), S-video, or composite video
Sampling
10-bits/color at 165 MHz maximum
Supports 1:1 sampling up to 1600x1200@60 Hz
Sources with native pixel rates > 165 MHz will be filtered
and undersampled at 165 Mhz, including:
• 1920x1080p@60 (173.0 MHz)
• 1920x1200@60 (193.25 MHz)
• 2048x1080p@60 (183.75 MHz)
Inputs 7 - 8
Input 9
Connector
DVI-I, per DDWG 1.0
Format (Digital)
8-bit DVI, RGBHV data via analog pins
Format (Analog)
RGBHV / RGBS / RGsB computer video, YPbPr video
(SD or HD), S-video, or composite video
HDCP hardware support
HDCP version 1.0 compliant
Connector
BNC
Format
SD-SDI per SMPTE 259M-C (NTSC/PAL resolution)
HD-SDI per SMPTE 292M (HDTV)
lìíéìí=péÉÅáÑáÅ~íáçåë
The table below lists DCS-200 output specifications:
Table A-2. DCS-200 Output Specifications
Parameter
Outputs
116
Detail
Specification
DVI output
1 x DVI connector
RGB output
1 x HD-15 VGA connector
HDCP Encryption
On DVI connector only
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
Physical and Electrical Specifications
mÜóëáÅ~ä=~åÇ=bäÉÅíêáÅ~ä=péÉÅáÑáÅ~íáçåë=
The table below lists DCS-200 physical and electrical specifications.
Table A-3. DCS-200 Physical and Electrical Specifications
Parameter
Power
Mechanical
Detail
Specification
Connector
Standard IEC, integral on/off switch
Power
100-240 VAC, 50-60 Hz
Chassis
H: 3.50 in. (8.89 cm), 2 RU rack mount
W: 17.00 in. (43.18 cm), 19.00 in. (48.26 cm) + wings
D: 14.25 in. (36.19 cm)
Temperature
0-40 degrees C
Humidity
0-95% non-condensing
Weight
7.5 lbs (3.40 kg)
Shipping Weight
22.0 lbs (9.97 kg)
`çããìåáÅ~íáçåë=péÉÅáÑáÅ~íáçåë=
The table below lists DCS-200 communications specifications.
Table A-4. DCS-200 Communications Specifications
Parameter
Communications
Detail
Specification
Ethernet
RJ-45, 10/100 Mbps
Serial
DB-9 Female, DCE, 115k Baud
^ÖÉåÅó=péÉÅáÑáÅ~íáçåë=
The table below lists DCS-200 agency specifications.
Table A-5. DCS-200 Agency Specifications
Parameter
Agency Specifications
DCS-200 • User’s Guide
Detail
Specification
EMI/EMC
EN55103-1 E4, EN55103-2, FCC Part 15 Subpart B Class A
Safety
EN 60950 Class 1
117
^K==péÉÅáÑáÅ~íáçåë
Pinouts
máåçìíë=
The following topics are discussed in this section:
•
•
•
•
Analog 15-pin D Connector
DVI-I Connector
Ethernet Connector
Serial Connector
^å~äçÖ=NRJéáå=a=`çååÉÅíçê
The figure below illustrates the analog 15-pin D connector:
5
1
10
6
15
11
Figure A-1. Analog 15-pin D connector, chassis view
The table below lists Analog 15-pin D connector pinouts.
Table A-6. Analog 15-pin D Connector Pinouts
Pin
118
Signal
Pin
Signal
1
Red
9
+5V DDC Power
2
Green
10
GND
3
Blue
11
4
12
DDC Data
5
13
H Sync or C Sync
6
Red return
14
V Sync
7
Green return
15
DDC Clock
8
Blue return
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
Pinouts
asfJf=`çååÉÅíçê
The figure below illustrates the DVI-I connector:
1
8 C1 C2
9
C5
17
24 C3 C4
Figure A-2. DVI-I connector
The table below lists DVI-I connector pinouts. Please note:
•
•
T.M.D.S = Transition Minimized Differential Signal
DDC = Display Data Channel
Table A-7. DVI-I Connector Pinouts
Pin
Signal
Pin
Signal
1
T.M.D.S. Data 2-
13
T.M.D.S. Data 3+
2
T.M.D.S. Data 2+
14
+5V Power
3
T.M.D.S. Data 2/4 Shield
15
ground (for +5V)
4
T.M.D.S. Data 4-
16
Hot Plug Detect
5
T.M.D.S. Data 4+
17
T.M.D.S. Data 0-
6
DDC Clock
18
T.M.D.S. Data 0+
7
DDC Data
19
T.M.D.S. Data 0/5 Shield
8
Analog Vertical Sync
20
T.M.D.S. Data 5-
9
T.M.D.S. Data 1-
21
T.M.D.S. Data 5+
10
T.M.D.S. Data 1+
22
T.M.D.S. Clock Shield
11
T.M.D.S. Data 1/3 Shield
23
T.M.D.S. Clock +
12
T.M.D.S. Data 3-
24
T.M.D.S. Clock -
MicroCross Pins
C1
Analog Red Video
C4
Analog Horizontal Sync
C2
Analog Green Video
C5
Analog Common Ground Return
C3
Analog Blue Video
DCS-200 • User’s Guide
119
^K==péÉÅáÑáÅ~íáçåë
Pinouts
bíÜÉêåÉí=`çååÉÅíçê
The figure below illustrates the Ethernet connector:
1
8
Figure A-3. Ethernet connector
The table below lists Ethernet connector pinouts.
Table A-8. Ethernet Connector Pinouts
Pin
Wire Color
1
TX Data +
White / Orange
2
TX Data -
Orange
3
RX Data +
White / Green
4
Blue
5
White / Blue
6
120
Signal
RX Data -
Green
7
White / Brown
8
Brown
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
Pinouts
pÉêá~ä=`çååÉÅíçê
The figure below illustrates the DB-9 Serial connector.
5
1
9
6
Figure A-4. Serial connector
The table below lists Serial connector pinouts.
Table A-9. Serial Connector Pinouts
Pin
RS-232 Signal
Description
1
CD
Carrier Detect
2
TXD
Transmitted Data
3
RXD
Received Data
4
DSR
Data Set Ready
5
GND
Signal Ground
6
DTR
Data Terminal Ready
7
CTS
Clear To Send
8
RTS
Request To Send
9
RI
Unused
DCS-200 • User’s Guide
121
^K==péÉÅáÑáÅ~íáçåë
Format Table
cçêã~í=q~ÄäÉ
The table below lists the available input and output formats for the DCS-200. Each entry
uses the following convention: Format @Fv (Hz). Most of the formats listed in this table
are supported for inputs and outputs. Formats that are supported only for input or only for
output sources are designated in bold in the Input/Output column.
Note
The DCS-200’s output can be set to progressive formats only.
Table A-10. DCS-200 Input and Output Formats
Format
122
Input Color Space
Input/Output
Apple 1200p @60
RGB
Input/Output
NTSC (480i)
SMPTE
Input Only
PAL (576i)
SMPTE
Input Only
640x480 @59.94
RGB
Input/Output
640x480 @60
RGB
Input/Output
640x480 @72
RGB
Input/Output
640x480 @75
RGB
Input/Output
640x480 @85
RGB
Input/Output
720x480p
SMPTE, RGB
Input/Output
720x575p
SMPTE, RGB
Input/Output
800x600 @50
RGB
Input/Output
800x600 @56
RGB
Input/Output
800x600 @59.94
RGB
Input/Output
800x600 @60
RGB
Input/Output
800x600 @72
RGB
Input/Output
800x600 @75
RGB
Input/Output
800x600 @85
RGB
Input/Output
875p
RGB
Input/Output
1024x768 @47.95
RGB
Input/Output
1024x768 @48
RGB
Input/Output
1024x768 @50
RGB
Input/Output
1024x768 @59.94
RGB
Input/Output
1024x768 @60
RGB
Input/Output
1024x768 @70
RGB
Input/Output
1024x768 @71.93
RGB
Input/Output
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
Format Table
Table A-10. DCS-200 Input and Output Formats (Continued)
Format
Input Color Space
Input/Output
1024x768 @72
RGB
Input/Output
1024x768 @75
RGB
Input/Output
1024x768 @85
RGB
Input/Output
1152x864 @75
RGB
Input/Output
1280x720 @60
RGB
Input Only
1280x720 @60 II
RGB
Input Only
1280x720p @48
SMPTE, RGB
Input/Output
1280x720p @50
SMPTE, RGB
Input/Output
1280x720p @59.94
SMPTE, RGB
Input/Output
1280x720p @60
SMPTE, RGB
Input/Output
1280x768 @47.95
RGB
Input/Output
1280x768 @48
RGB
Input/Output
1280x768 @50
RGB
Input/Output
1280x768 @59.94
RGB
Input/Output
1280x768 @75
RGB
Input/Output
1280x800 @60
RGB
Input/Output
1280x800 @60 II
RGB
Input Only
1280x960 @50
RGB
Input/Output
1280x960 @59.94
RGB
Input/Output
1280x960 @60
RGB
Input/Output
1280x960 @85
RGB
Input/Output
1280x1024 @47.95
RGB
Input/Output
1280x1024 @48
RGB
Input/Output
1280x1024 @50
RGB
Input/Output
1280x1024 @59.94
RGB
Input/Output
1280x1024 @60
RGB
Input/Output
1280x1024 @71.93
RGB
Input/Output
1280x1024 @72
RGB
Input/Output
1280x1024 @75
RGB
Input/Output
1280x1024 @85
RGB
Input/Output
1360x768 @60
RGB
Input/Output
1364x768 @47.95
RGB
Input/Output
1364x768 @48
RGB
Input/Output
DCS-200 • User’s Guide
123
^K==péÉÅáÑáÅ~íáçåë
Format Table
Table A-10. DCS-200 Input and Output Formats (Continued)
Format
124
Input Color Space
Input/Output
1364x768 @50
RGB
Input/Output
1364x768 @59.94
RGB
Input/Output
1364x768 @75
RGB
Input/Output
1364x1024 @47.95
RGB
Input/Output
1364x1024 @48
RGB
Input/Output
1364x1024 @50
RGB
Input/Output
1364x1024 @59.94
RGB
Input/Output
1364x1024 @75
RGB
Input/Output
1366x768 @50
RGB
Input/Output
1366x768 @59.94
RGB
Input/Output
1400x1050 @48
RGB
Input/Output
1400x1050 @50
RGB
Input/Output
1400x1050 @59.94
RGB
Input/Output
1400x1050 @60
RGB
Input/Output
1400x1050 @75
RGB
Input/Output
1440x900 @60
RGB
Input/Output
1440x900 @75
RGB
Input/Output
1440x900 @85
RGB
Input/Output
1536x768 @50
RGB
Input/Output
1536x768 @59.94
RGB
Input/Output
1600x1200 @47.95
RGB
Input/Output
1600x1200 @48
RGB
Input/Output
1600x1200 @50
RGB
Input/Output
1600x1200 @59.94
RGB
Input/Output
1600x1200 @60
RGB
Input/Output
1680x1050 @60
RGB
Input/Output
1920x1080i @50
SMPTE, RGB
Input Only
1920x1080i @59.94
SMPTE, RGB
Input Only
1920x1080i @60
SMPTE, RGB
Input Only
1920x1080p @23.98
SMPTE, RGB
Input/Output
1920x1080p @24
SMPTE, RGB
Input/Output
1920x1080p @25
SMPTE, RGB
Input/Output
1920x1080p @29.97
SMPTE, RGB
Input/Output
DCS-200 • User’s Guide
^K==péÉÅáÑáÅ~íáçåë
Format Table
Table A-10. DCS-200 Input and Output Formats (Continued)
Format
Input Color Space
Input/Output
1920x1080p @30
SMPTE, RGB
Input/Output
1920x1080p @48
SMPTE, RGB
Input/Output
1920x1080p @50
SMPTE, RGB
Input/Output
1920x1080p @59.94
SMPTE, RGB
Input/Output
1920x1080p @60
SMPTE, RGB
Input/Output
1920x1080p II @50
SMPTE, RGB
Output Only
1920x1080p II @60
SMPTE, RGB
Input Only
1920x1080sF@23.98
SMPTE, RGB
Input Only
1920x1080sF@24
SMPTE, RGB
Input Only
1920x1200p @60
RGB
Input/Output
1920x1200p II @60
RGB
Output Only
2048x1080p @48
RGB
Input/Output
2048x1080p @50
RGB
Input/Output
2048x1080p @59.94
RGB
Input/Output
2048x1080p @60
RGB
Input/Output
2048x1080p II @50
RGB
Input/Output
2048x1080p II @60
RGB
Output Only
DCS-200 • User’s Guide
125
^K==péÉÅáÑáÅ~íáçåë
Format Table
126
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
få=qÜáë=^ééÉåÇáñ
This appendix provides information regarding remote control protocol. The following
topics are discussed:
•
•
•
•
•
Communicating with DCS-200
Command Protocol
Error Codes
DCS-200 Command List
Remote Commands
`çããìåáÅ~íáåÖ=ïáíÜ=a`pJOMM
„ Use the following steps to communicate with the DCS-200 via Telnet:
1.
Connect the DCS-200’s Ethernet port to an Ethernet switch, and connect the
switch to your PC or laptop.
2.
Ensure that all Ethernet parameters are properly set up. In Chapter 4, refer to the
“Ethernet” section on page 74 for details.
3.
For Telnet communications, use the DCS-200’s IP address and port 23. On a
Microsoft Windows PC, open a command prompt window and enter the following:
> telnet xxx.xxx.xxx.xxx
4.
23
After you “Telnet” into the DCS-200, you are presented with the login prompt:
Welcome to DCS-200.
Login as “user”.
Press <ENTER> for password.
a.
Type “user” and press ENTER to login.
b.
When prompted for a password, press ENTER.
Once you have successfully logged in, the following message appears, along with
the command prompt (>):
ShellApp waiting for input
>
5.
You can now issue commands. Operationally, the telnet window functions in a
manner similar to a serial communications session. As required, type "help" to
see a list of supported commands.
Refer to the “Remote Commands” section on page 134 for a complete list of commands.
DCS-200 • User’s Guide
127
_K==oÉãçíÉ=`çåíêçä
Command Protocol
`çãã~åÇ=mêçíçÅçä
The DCS-200’s command protocol is compatible with GNU getopt parsing. Every
parameter of the command has an option character associated with it. A <CR> carriage
return (ASCII 13) terminates the command.
Note
The order of the option characters in the command does not
matter.
S Command example:
ITYPE -i 2 -t 1<CR>
Or
ITYPE -t 1 -i 2<CR>
`çãã~åÇ=oÉëéçåëÉë
A command response is sent after each command is processed. This response consists of
the command, followed by the error code, a line feed <LF> and a special termination
character (\x4).
•
When a command is successful, the error code is a 0 (eERR_OK), or some
positive value.
•
When a command is not successful, the error code is a negative value. A
preliminary list of the error codes is included. Refer to the “Error Codes” section
on page 130 for details.
S Command response example:
ITYPE -e 0<LF>
</x4>
nìÉêó=léíáçåë
Query type options are available for the commands. The order of precedence for
processing query option arguments is help (--help), query (-?), and list (--list). If more than
one query option is sent in a command, the option with the highest precedence is
processed, and any others are ignored.
Help Query — Commands have a “help” query option associated with them, (--help). This
query lists all option flags and parameters for the command in the following format:
S Help option example:
IBRT --help<CR>
S Response:
f_oq
•
•
128
Description: Input Brightness Adjust
Command Format: IBRT -i(input) -b(bright)
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Command Protocol
•
Parameters:
-i(input): Input number, 1-8
-b(bright): 75.0%-125.0%
•
•
Query Format: IBRT i(input) -?
Query Response: IBRT i(input) b(bright) --min 75 --max 125
IBRT -e 0 <LF>
</x4>
Current Setting Query — The current setting query option (-?) returns the command with
each of the current parameter settings. Commands with minimum and maximum settings
for the parameter will have these “min” and “max” values returned with option flags --min
and --max.
S Query option example:
IBRT -i 4 -?<CR>
S Response:
IBRT -i 4 -b 100.00 --min 75 --max 125
IBRT -e 0<LF>
</x4>
Several commands have a list for the associated valid parameter values, such as the
format commands. The list of these values can be queried with the list query option (--list).
The list shows has the numeric value for the parameter, followed by the value text encased
in quotes. A colon separates the numeric value from the string.
S List query option example:
ISMP -i 4 --list<CR>
S Response:
0:"OverSample"
1:"1:1"
ISMP -e 0<LF>
</x4>
DCS-200 • User’s Guide
129
_K==oÉãçíÉ=`çåíêçä
Error Codes
bêêçê=`çÇÉë
This section provides DCS-200 error codes:
bêêçê=`çÇÉëW==dÉåÉê~ä=c~áäìêÉë
The table below lists general failure codes:
Table B-1. DCS-200 General Error Codes
Code
Description
-9999
Generic fail
-9998
Operation is not applicable in current state
-9997
UI Related... Did not get response from device
-9996
UI Related... Did not get valid response from device
-9995
Timeout occurred
-9994
Parameter / data out of range
-9993
Searching for data in an index, no matching data
-9992
Checksum didn't match
-9991
Version didn't match
-9990
UI Related... Current device interface not supported
-9989
Pointer operation invalid
-9988
Part of command had error
-9987
Buffer overflow
-9986
Initialization is not done (still in progress)
bêêçê=`çÇÉëW==kç=bêêçê
The table below lists the “no error” code:
Table B-2. DCS-200 “No Error” Code
Code
0
130
Description
Successful
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
DCS-200 Command List
a`pJOMM=`çãã~åÇ=iáëí
The table below lists DCS-200 remote commands.
Table B-3. DCS-200 Remote Commands
Command
Description
Page
Ethernet Commands
DHCP
Enable/Disable DHCP mode
134
EMAC
Get MAC Address
134
GATEWAY
Set gateway to be used when DHCP is OFF
135
IP
Set Static IP Address to be used when DHCP is OFF
135
SUBNET
Set subnet mask to be used when DHCP is OFF
135
Input Commands
ACQ
Input Source Acquire. Does a "force" acquire of the input
135
AUTOACQ
Auto Input Acquisition Mode
135
BACKGND
Set background color
136
BLKVID
Puts black into the scaler selected
136
CBLEQ
Set cable equalization
136
EDID
Set Input EDID Resolution
136
EDIDTYPE
Set EDID type
137
FREEZE
Freeze the input on program
137
IADJ
Selects the input path to adjust (preview or program)
137
IAR
Adjust Input Aspect Ratio
137
IAUTOC
Attempts to detect and adjust input video to the active video area
138
IAVAIL
Query only command for input availability
138
IBRT
Input brightness adjust
138
ICDEL
Delete Input Configuration
139
ICNT
Input contrast adjust
139
ICPHO
Input Phase Adjust
139
ICREC
Recalls saved input configuration for selected input
139
ICRST
Reset Input Configuration to default values
140
ICSAV
Saves Input Configuration
140
ICSP
Input Colorspace Adjust
140
IHATV
Input Horizontal Active Adjust
140
IHCROP
Input Horizontal Crop
141
DCS-200 • User’s Guide
131
_K==oÉãçíÉ=`çåíêçä
DCS-200 Command List
Table B-3. DCS-200 Remote Commands (Continued)
Command
Description
Page
IHPAN
Input Horizontal Pan
141
IHPOS
Input Horizontal Position Adjust
141
IHTOTAL
Input Horizontal Total Adjust
142
IHUE
Input Hue Adjust
142
IMAP
Maps the input file configuration for the selected input
142
IRBRT
Input RGB Brightness Adjust
142
IRCNT
Input RGB Contrast Adjust
143
IRES
Input Resolution Select
143
ISAT
Input Saturation Adjust
143
ISEL
Selects the selected input as the current input to display
144
ISLICE
Input Sync Slice Threshold Adjust
144
ISMP
Adjust Input Sample mode
144
ISYNC
Input Sync Type Adjust
145
ITYPE
Input Type Adjust
145
IVATV
Input Vertical Active Adjust
146
IVCROP
Input Vertical Crop
146
IVPAN
Input Vertical Pan
146
IVPOS
Input Vertical Position Adjust
146
IVTOTAL
Input Vertical Total Adjust. Query-only command.
147
PCOMP
Pulldown Compensation mode adjust
147
TAKE
Take the input currently on preview onto program
147
Output Commands
BLACK
Set the mixer output to black
147
OAVAIL
Checks availability of the preview output. Query-only command.
147
OCSAV
Save Output Configuration
147
OGM
Set Output Gamma
148
ORBM
Output Raster Box Mode
148
ORES
Output Resolution
148
OSRC
Select the input source for the preview output
149
OSYNC
Output Sync Type Adjust
149
OTPM
Output Test Pattern Mode
149
OTPT
Output Test Pattern Type
150
132
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
DCS-200 Command List
Table B-3. DCS-200 Remote Commands (Continued)
Command
Description
Page
System Commands
AUTOCFG
Auto Input Configuration Mode
151
AUTOSAVE
Auto Input Settings Save
151
AUTOTAKE
Auto Take Mode
151
BLKTRAN
Set whether going to black is a direct cut or setup for a take
151
CONTEXT
Set menu context
151
DIAG
Perform a system diagnostic test
152
DIAGD
Display the results of the last performed system diagnostic test
152
ISTAT
Query only command for the input status type and format.
152
LCLR
Clear the selected log (ram copy, not flash)
152
LDMP
Display the current log messages
152
LFEN
Set the mode for the selected log
153
LINT
Set the time interval for writing the enabled logs to flash
153
LOCKOUT
Control the lockout mode of the front panel
153
OSTAT
Query only command for the output status type and format
153
PREVIEW
Query only command for the input, key and black button status on preview
153
PROGRAM
Query only command for the input, key and black button status on program
154
RESET
Reset unit
154
SAVE
System Save
154
SERIAL
Sets the serial port
154
TEMP
Query only command for the temperature of the unit
155
TRNTIME
Set transition time
155
VER
Display Version info
155
VFDBRT
Set VFD brightness
155
Key Commands
LKEY
Luminance Key definition
155
LOGO Commands
LOGODEL
Delete the selected logo file
156
LOGOSAVE
Save the image on Program to the selected logo fame store and file
157
LOGOSEL
Logo selection
157
LOGOSTAT
The logo format status. This command is a query only.
157
DCS-200 • User’s Guide
133
_K==oÉãçíÉ=`çåíêçä
Remote Commands
oÉãçíÉ=`çãã~åÇë
This section lists DCS-200 remote commands, in the following categories:
•
•
•
•
•
•
Ethernet Commands
Input Commands
Output Commands
System Commands
Key Commands
LOGO Commands
bíÜÉêåÉí=`çãã~åÇë
ae`m
•
•
•
•
•
bj^`
•
•
•
•
•
•
134
Description: Enables/disables DHCP mode.
Command Format: DHCP -m (mode)
Command Params: -m mode: 0-disable, 1-enable (default: on)
Query Format: DHCP -?
Query Response: DHCP -m (mode) --min 0 --max 1
Description: Gets MAC Address.
Command Format: N/A
Command Params: N/A
Query Format: EMAC -?
Query Response: EMAC -a (addr)
Response Params: -a (addr): MAC address formatted xx.xx.xx.xx.xx.xx
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
d^qbt^v
• Description: Sets gateway to be used when DHCP is OFF.
• Command Format: GATEWAY -s (static addr)
• Command Params: s static addr: format will be: xxx.xxx.xxx.xxx
• Query Format: GATEWAY -?
• Query Response: GATEWAY -a (active addr) -s (static addr)
• Query Params: -a (active addr): Active gateway active address
fm
•
•
•
•
•
•
Description: Sets Static IP Address to be used when DHCP is OFF.
Command Format: IP -s (static)
Command Params: -s static addr with format xxx.xxx.xxx.xxx
Query Format: IP -?
Query Response: IP -a (active addr) -s (static addr)
Response Params: -a (active addr): returns active address
pr_kbq
• Description: Sets subnet mask to be used when DHCP is OFF.
• Command Format: SUBNET -s (static addr)
• Command Params: -s static address formatted xxx.xxx.xxx.xxx
• Query Format: SUBNET -?
• Query Response: SUBNET -a(active addr) -s(static addr)
• Response Params: -a(active addr): returns active address
fåéìí=`çãã~åÇë
^`n
•
•
•
•
Description: Input Source Acquire. Does a "force" acquire of the input.
Command Format: ACQ -i (input)
Parameters: -i (input): Input number
Query Format: N/A
^rql^`n
• Description: Auto Input Acquisition Mode
• Command Format: AUTOACQ -m (mode)
• Command Params: -m mode: 0-off, 1-on (Default: on)
• Query Format: AUTOACQ -?
• Query Response: AUTOACQ -m (mode) --min 0 --max 1
DCS-200 • User’s Guide
135
_K==oÉãçíÉ=`çåíêçä
Remote Commands
_^`hdka
• Description: Sets background color.
• Command Format: BACKGND -i (input) -b (background)
• Parameters: -b (background):1-black, 2-gray
• Query Format: BACKGND -?
• Query Response: BACKGND -b (background) --min 1 -- max 2
• List Format: BACKGND --list
• List Response: 1:"Black"
2:"Gray"
_ihsfa
• Description: Puts black into the selected scaler.
• Command Format: BLKVID -s (scaler) -m (mode)
• Parameters:
-s (scaler): 1 - 2
-m (mode): 0 - off, 1 - on
•
•
Query Format: N/A
Query Response: N/A
`_ibn
• Description:
Sets cable equalization. Command valid only for DVI input
channels.
•
•
Command Format: CBLEQ -i(input) -c(cable equalization)
Parameters:
-i (input): 7-8
-c (cable equalization): 0 - 15 (Default: 12)
•
•
bafa
•
•
•
Query Format: CBLEQ -i(input) -?
Query Response: CBLEQ -i(input) -c (cable equalization) --min 0 --max 15
Description: Sets Input EDID Resolution.
Command Format: EDID -i (input) [-f (format) | -n (index)]
Parameters:
-i (input) : 1-8
-f (format): Format string, i.e. "1024x768 @59.94"
or
-n (index): Video format index
•
•
•
136
Query Format: EDID -i (input) -?
Query Response: EDID -i (input) -f (format)
List Format: EDID -i (input) --list
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
List Response:
2:"720x480p"
4:"720x575p"
5:"640x480 @59.94"
Etc.
bafaqvmb
• Description:
Sets EDID type. This command is valid only for the DVI input
channels.
•
•
Command Format: EDIDTYPE -i(input) -t(EDID type)
Parameters:
-i (input): 7-8
-t (EDID type): 0 - analog, 1 - digital (Default: 1)
•
•
•
•
Query Format: EDIDTYPE -i(input) -?
Query Response: EDIDTYPE -i(input) -t (EDID type) --min 0 --max 1
List Format: EDIDTYPE -i(input)
List Response:
0:"Analog"
1:"Digital"
cobbwb
• Description: Freezes the input on program.
• Command Format: FREEZE -m (mode)
• Command Params: -m mode: 0-off, 1-on (Default: off)
• Query Format: FREEZE -?
• Query Response: FREEZE -m (mode) --min 0 --max 1
f^ag
•
•
•
•
•
•
•
Description: Selects the input path to be adjusted (preview or program).
Command Format: IADJ -p (path)
Parameters:-p (path): 0-preview, 1-program
Query Format: ADJ -?
Query Response: IADJ -p (path)
List Format: IADJ --list
List Response: 0: "PREVIEW"
1: "PROGRAM"
f^o=
•
•
DCS-200 • User’s Guide
Description: Adjust Input Aspect Ratio
Command Format: IAR -i (input) -r (ratio) -c (custom ratio)
137
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Parameters:
-i (input): 1 - 9
-r (ratio): 1 - 1:1, 2 - 3:2, 3 - 4:3, 4 - 5:4, 5 - 16:9
-c (custom ratio): .75 - 3.0
•
•
Query Format: IAR -i (input) -?
Query Response: IAR -i (input) -c (custom ratio) --min .75 -- max 3
or
IAR -i (input) -r (ratio) --min 1 -- max 5
•
•
List Format: IAR -i (input) --list
List Response: 1:"1:1"
2:"3:2"
3:"4:3"
4:"5:4"
5:"16:9"
f^rql`=
• Description:
Attempts to detect and adjust input video to the active video area.
This command is only for analog input types.
•
•
•
•
Command Format: IAUTOC -i (input)
Parameters: -i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog)
Query Format: N/A
Query Response: N/A
f^s^fi
• Description:
Query-only command for input availability. This command can be
used to identify whether the SDI board is present by querying for input 9.
•
Parameters: -i (input):1 - 9
-m (mode): 0 - input not available, 1 - input available
•
•
f_oq
•
•
•
Query Format: IAVAIL -i (input) -?
Query Response: IAVAIL -i (input) -m (mode)
Description: Input Brightness Adjust
Command Format: IBRT -i(input) -b (bright)
Parameters:
-i (input): 1-9
-b (bright): 75.0% - 125.0% (Default: 100%)
•
•
138
Query Format: IBRT -i (input) -?
Query Response: IBRT -i (input) -b(bright) --min 75 --max 125
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
f`abi=
•
•
•
Description: Deletes input configuration.
Command Format: ICDEL -i(input) -f(file)
Parameters: -i(input):1 - 9
-f(file): 1 - 64. If specified, update the File Association menu to reflect the
selected file number. If not specified, use the current file number from the
ICREC query.
•
•
f`kq
•
•
•
Query Format: N/A
Query Response: N/A
Description: Input Contrast Adjust
Command Format: ICNT -i(input) -c(contrast)
Parameters:
-i (input): 1-9
-c (contrast): 75.0% - 125.0% (Default: 100%)
•
•
f`mel
•
•
•
Query Format: ICNT - i(input) -?
Query Response: ICNT -i(input) -c(contrast) --min 75 --max 125
Description: Input Phase Adjust. This command is only valid for analog input
types.
Command Format: ICPHO -i(input) -a(ADC) -p(phase)
Parameters: -i (input): 1 - 8 (7 & 8 only if itype is analog)
-a (ADC): A/B (A:ADC A, B:ADC B)
-p (phase): -16 - 15 (default: 0)
•
•
f`ob`=
•
•
•
Query Format: ICPHO -i(input) -a(ADC) -?
Query Response: ICPHO -i(input) -a(ADC) -p(phase) --min -16 --max 15
Description: Recalls the saved input configuration for selected input. The
selected input’s IMAP is updated if the -f (file) parameter is specified.
Command Format: ICREC -i (input) -f (file)
Parameters: -i (input):1 - 9
-f (file): 1 - 64. If specified, update the File Association menu to reflect the
selected file number.
•
•
•
Query Format: ICREC -i (input) -?
Query Response: ICREC -i (input) -f (file)
List Format: ICREC -i (input) --list
The list returns all saved input formats.
•
DCS-200 • User’s Guide
List Response:
139
_K==oÉãçíÉ=`çåíêçä
Remote Commands
1:"1"
2:"2"
.
.
64:"64"
f`opq
•
•
•
•
•
f`p^s=
•
•
•
Description: Reset Input Configuration to the input default values
Command Format: ICRST -i (input)
Parameters: -i (input): 1 - 9
Query Format: N/A
Query Response: N/A
Description: Saves Input Configuration. The input’s IMAP is updated if the
-f (file) parameter is specified.
Command Format: ICSAV -i (input) -f (file)
Parameters: -i (input):1 - 9
-f (file): 1 - 64. If specified, update the File Association menu to reflect
the selected file number. If not specified, use the current file number
from the ICREC query.
•
•
f`pm
•
•
•
Query Format: N/A
Query Response: N/A
Description: Input Colorspace Adjust
Command Format: ICSP -i (input) -c (color)
Parameters:
-i (input): 1 - 9
-c (color): 0-RGB, 1-SMPTE
•
•
•
Query Format: ICSP -i (input) -?
Query Response: ICSP -i (input) -c (color) --min 0 --max 1
List Format: Each input type will have a different list for colorspace.
ICSP -i (input) --list
fe^qs
•
•
140
Description: Input Horizontal Active Adjust. This command is only adjustable for
analog input types. Other input types will provide query information only.
Command Format: IHATV -i (input) -a (active)
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog); 1 - 9 for
query
-a (active): In pixels
•
•
Query Format: IHATV -i (input) -?
Query Response:
IHATV -i (input) -a (active) --min (active min) -- max (active max)
fe`olm=
• Description: Input Horizontal Crop
• Command Format: IHCROP -i (input)
• Parameters:
-w (width)
-i (input): 1 - 9
-w (width): In pixels
•
•
Query Format: IHCROP -i (input) -?
Query Response: IHCROP -i (input) -w(width) --min (pos min) -- max (pos max)
fem^k=
• Description: Input Horizontal Pan
• Command Format: IHPAN -i (input)
• Parameters:
-p (pan)
-i (input): 1 - 9
-p (pan): In pixels
•
•
femlp
•
•
•
Query Format: IHPAN -i (input) -?
Query Response: IHPAN -i (input) -p (pan) --min (active min) -- max (active
max)
Description: Input Horizontal Position Adjust. This command is only adjustable
for analog input types. Other input types will provide query information only.
Command Format: IHPOS -i (input) -p (position)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog); 1 - 9 for
query
-p (position): In pixels
•
•
Query Format: IHPOS -i (input) -?
Query Response:
IHPOS -i (input) -p (position) --min (pos min) -- max (pos max)
DCS-200 • User’s Guide
141
_K==oÉãçíÉ=`çåíêçä
Remote Commands
feqlq^i
• Description:
Input Horizontal Total Adjust. This command is only adjustable for
analog input types. Other input types will provide query information only.
•
•
Command Format: IHTOTAL -i (input) -t (total)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog); 1 - 9 for
query
-t(total): In pixels
•
•
ferb
•
•
•
Query Format: IHTOTAL -i (input) -?
Query Response: IHTOTAL -i (input) -t (total) --min (total min) -- max (total max)
Description: Input Hue Adjust. This command is only valid for SDI, Y/C and
CVBS inputs.
Command Format: IHUE -i (input) -h (hue)
Parameters:
-i (input): 1 - 9
-h (hue): -90 - +90 (Default: 0)
•
•
fj^m
•
•
•
Query Format: IHUE -i (input) -?
Query Response: IHUE -i (input) -h (hue) --min -90 --max 90
Description: Maps the input file configuration for the selected input.
Command Format: IMAP -i (input) -f (file)
Parameters: -i (input):1 - 9
-f (file): 1 - 64
•
•
fo_oq
•
•
•
Query Format: IMAP -i (input) -?
Query Response: IMAP -i (input) -f (file)
Description: Input RGB Brightness Adjust. This command is only valid for
formats with the RGB color space.
Command Format: IRBRT -i (input) -r (red) -g (green) -b (blue)
Parameters:
-i (input): 1 - 8
-r (red): -25.0% - 25.0% (Default: 0%)
-g (green): -25.0% - 25.0% (Default: 0%)
-b (blue): -25.0% - 25.0% (Default: 0%)
•
142
Query Format: IRBRT -i input -?
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Query Response:
IRBRT -i (input) -r (red) -g (green) -b (blue) --min -25 --max 25
fo`kq
•
•
•
Description: Input RGB Contrast Adjust. This command is only valid for formats
with the RGB color space.
Command Format: IRCNT -i (input) -r (red) -g (green) -b (blue)
Parameters:
-i (input): 1 - 8
-r (red): -25.0% - 25.0% (Default: 0%)
-g (green): -25.0% - 25.0% (Default: 0%)
-b (blue): -25.0% - 25.0% (Default: 0%)
•
•
Query Format: IRCNT -i (input) -?
Query Response:
IRCNT -i (input) -r(red) -g(green) -b(blue) --min 75 --max 125
fobp
•
•
•
Description: Input Resolution Select
Command Format: IRES -i (input) [-f (format) | -n (index)]
Parameters: -i (input): 1 - 9
-f (format): format string, i.e. "800x600 @59.94"
or
-n (index): video format index (see --list)
-s (status): 0 - valid, non-zero - invalid
•
•
•
Query Format: IRES -i (input) -?
Query Response: IRES -i (input) -f (format) -s (status)
List Format: Each input type has a different list of valid resolutions.
IRES -i (input) --list
•
List Response: Example for input type of analog:
1:"NTSC (480i)"
2:"720x480p"
3:"PAL (576i)"
Etc.
fp^q
•
•
DCS-200 • User’s Guide
Description: Input Saturation Adjust. This command is only valid for the SMPTE
color space.
Command Format: ISAT -i (input) -s (sat)
143
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Parameters:
-i (input): 1 - 9
-s (saturation): 0 - 150 (Default: 100)
•
•
•
Query Format: ISAT -i (input) -?
Query Response: ISAT -i (input) -s (sat) --min 75 --max 125
List Response: 0:"RGB"
1:"SMPTE"
fpbi
•
•
•
Description: Selects the specified input as the current input to display. This
command will perform the valid sync check, route the input, recall video if saved
or acquire source if not saved. Includes the -f (file) parameter option. Also, the
IMAP will be updated for the input if the file parameter is specified.
Command Format: ISEL -i (input) -f (file
Parameters: -i (input): 1 - 9
-f (file): 1 - 64; If specified, updates the File Association menu to reflect
the selected file number. If not specified, uses the file number specified
in the ICREC query.
•
•
Query Format: ISEL -?
Query Response: ISEL -i (input)
fpif`b=
• Description:
Input Sync Slice Threshold Adjust. This command is only valid for
analog inputs.
•
•
Command Format: ISLICE -i (input) -t (threshold)
Parameters: -i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog)
-t(threshold): 8 - 256mV; +8 increments (default: 128mV)
•
•
fpjm=
•
•
•
Query Format: ISLICE -i (input) -?
Query Response: ISLICE -i (input) -t (threshold) --min 8 -- max 256
Description: Adjust Input Sample mode. This command is only adjustable for
analog input types. Other input types will provide query information only.
Command Format: ISMP -i (input) -s (sample mode)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog); 1 - 9 for
query
-s (sample mode): 0 - over sample, 1 - 1:1 sampling (Default: 1:1)
•
•
144
Query Format: ISMP -i (input) -?
Query Response: ISMP -i (input) -s (sample mode) --min 0 -- max 1
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
List Format: Each input type has a different list of valid sample modes.
ISMP -i (input) --list
•
List Response: 0:"OverSample"
1:"1:1"
fpvk`
•
•
•
Description: Input Sync Type Adjust. This command is only valid for analog
input types.
Command Format: ISYNC -i (input) -s (sync)
Parameters: -i (input): 1 - 8 (7 & 8 only if itype is analog)
-s (sync): 0 - auto, 1 - H/V, 2- CSync, 3- SOG (Default: auto)
•
•
•
•
Query Format: ISYNC -i (input) -?
Query Response: ISYNC -i (input) -s(sync) --min 0 --max 3
List Format: ISYNC -i (input) --list
List Response: 0:"AUTO"
1:"H/V"
2:"CSYNC"
3:"SOG"
fqvmb
•
•
•
Description: Input Type Adjust. This command is only adjustable for the analog
inputs. Other inputs will provide query information only.
Command Format: ITYPE -i (input) -t (type)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if itype is analog) ; 1 - 9 for
query
-t (type): 1-analog, 2-Y/C, 3-CVBS, 4-SDI, 5-DVI, 6-YPbPr
•
•
•
Query Format: ITYPE -i (input) -?
Query Response: ITYPE -i (input) -t (type)
List Format: Each input type has a different list of valid input types.
ITYPE -i (input) --list
•
List Response: 1:"RGB"
2:"Y/C"
3:"CVBS"
4:"SDI"
5:"DVI"
6:"YPbPr"
DCS-200 • User’s Guide
145
_K==oÉãçíÉ=`çåíêçä
Remote Commands
fs^qs
•
•
•
Description: Input Vertical Active Adjust. This command is only adjustable for
analog input types. Other input types will provide query information only.
Command Format: IVATV -i (input) -a (active)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if input is analog); 1 - 9 for
query
-a (active): In lines
•
•
Query Format: IVATV -i (input) -?
Query Response: IVATV -i (input) -a (total) --min (active min) -- max (active
max)
fs`olm=
• Description: Input Vertical Crop
• Command Format: IVCROP -i (input)
• Parameters:
-h (height)
-i(input): 1 - 9
-h(height): In lines
•
•
Query Format: IVCROP -i(input) -?
Query Response: IVCROP -i(input) -h(height) --min (pos min) -- max (pos max)
fsm^k=
• Description: Input Vertical Pan
• Command Format: IVPAN -i (input)
• Parameters:
-p (pan)
-i (input): 1 - 9
-p (pan): In pixels
•
•
fsmlp
•
•
•
Query Format: IVPAN -i (input) -?
Query Response: IVPAN -i (input) -p (pan) --min (active min) -- max (active
max)
Description: Input Vertical Position Adjust. This command is only adjustable for
analog input types. Other input types will provide query information only.
Command Format: IVPOS -i (input) -p (position)
Parameters:
-i (input): 1 - 8 for adjustments (7 & 8 only if input is analog); 1 - 9 for
query
-p (position): In lines
•
•
146
Query Format: IVPOS -i (input) -?
Query Response: IVPOS -i (input) -p (position) --min (pos min) -- max (pos max)
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
fsqlq^i
• Description: Input Vertical Total Adjust. This command is a query only.
• Parameters: -i (input): 1 - 9
• Query Format: IVTOTAL -i (input) -?
• Query Response: IVTOTAL -i (input) -t (total)
m`ljm=
• Description: Pulldown Compensation mode adjust.
• Command Format: PCOMP -i (input) -m (mode)
• Parameters: -i (input):1 - 9
-m(mode): 0 - off, 1 - on (Default: off)
•
•
q^hb
•
•
•
Query Format: PCOMP -i (input) -?
Query Response: PCOMP -i (input) -m (mode) --min 0 -- max 1
Description: Take the input currently on preview onto program.
Command Format: TAKE
Command Params: None
lìíéìí=`çãã~åÇë
_i^`h=
• Description: Set the mixer to output black.
• Command Format: BLACK -m (mode)
• Parameters: -m (mode): 0 - off, 1 - on
• Query Format: BLACK -?
• Query Response: BLACK -m (mode) --min 0 --max 1
l^s^fi
• Description:
Query-only command used to identify whether the preview output
mezzanine is installed
•
•
Query Format: OAVAIL -o (output) -?
Parameters: -o (output): 1 - DVI, 3 - Preview DVI
-m (mode): 0 - output not available, 1 - output available
•
Query Response: OAVAIL -o (output) -m (mode)
l`p^s=
• Description: Save Output Configuration
• Command Format: OCSAV
DCS-200 • User’s Guide
147
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
•
•
ldj=
•
•
•
Parameters: -o output: 1 - DVI, 3 - Preview DVI
Query Format: N/A
Query Response: N/A
Description: Set Output Gamma
Command Format: OGM -o (output) -g (gamma)
Parameters:
-o output: 1 - DVI
-g gamma: 1.0 to 3.0; +0.1 increment (Default: 1.0)
•
•
Query Format: OGM -o (output) -?
Query Response: OGM -o (output) -g (gamma) --min 1 -- max 3
lo_j=
• Description: Output Raster Box Mode
• Command Format: ORBM -o (output)
• Parameters:
-m (mode)
-o (output): 1 - DVI, 3 - Preview DVI
-m (mode): 0-off, 1-on
•
•
lobp=
•
•
•
Query Format: ORBM -o (output) -?
Query Response: ORBM -o (output) -m (mode) --min 0 -- max 1
Description: Output Resolution
Command Format: ORES -o (output) [-f (format) | -n (index)]
Parameters: -o (output): 1 - DVI, 3 - Preview DVI
-f (format): format string, i.e. "1600x1200 @60"
(Default: 1024x768 @ 59.94)
or
-n (index): video format index (see list response)
•
•
•
•
Query Format: ORES -o (output) -?
Query Response: ORES -o (output) -f(format)
List Format: ORES -o (output) --list
List Response: 2: "720x480p"
4: "720x575p"
5:"640x480 @59.94"
6:"640x480 @60"
7:"640x480 @72"
8:"640x480 @75"
9:"640x480 @85"
148
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
10:"800x600 @50"
11:"800x600 @56"
12:"800x600 @59.94"
13:"800x600 @60"
14:"800x600 @72"
15:"800x600 @75"
16:"800x600 @85"
lpo`
•
•
•
•
•
•
•
Description: Selects the input source for the preview output (preview or
program).
Command Format: OSRC -s (source)
Parameters: -s (source): 0-preview, 1-program
Query Format: OSRC -?
Query Response: OSRC -s (source)
List Format: OSRC --list
List Response: 0:"PREVIEW"
1:"PROGRAM"
lpvk`=
• Description: Output Sync Type Adjust.
• Command Format: OSYNC -o (output) -s (sync)
• Parameters:
-o (output): 1 - DVI, 2 - Analog, 3 - Preview DVI, 4 - Preview Analog
-s (sync): 1 = +H+V, 2 = +H-V, 3 = -H+V, 4 = -H-V, 5=CSync for analog
only (Defaults: DVI : +H+V, analog: -H-V)
•
•
Query Format: OSYNC -o (output) -?
•
•
List Format: OSYNC -o (output) --list
Query Response: OSYNC -o (output) -s(sync) --min 1 --max 4 (max returned for
analog is 5)
List Response: 1:"+H+V"
2:"+H-V"
3:"-H+V"
4:"-H-V"
5.”CSync” (returned for analog only)
lqmj=
•
•
DCS-200 • User’s Guide
Description: Output Test Pattern Mode
Command Format: OTPM -o (output) - m (mode)
149
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Parameters:
-o (output): 1 - DVI, 3 - Preview DVI
-m (mode): 0 - off, 1 - on
•
•
lqmq=
•
•
•
•
Query Format: OTPM -o (output) -?
Query Response: OTPM -o (output) - m (mode) --min 0 -- max 1
Description: Output Test Pattern Type
Command Format: OTPT -o (output) - t (type)
Parameters: -o (output): 1 - DVI, 3 - Preview DVI
-t (type): 1 - H Ramp
2 - V Ramp
3 - 100% Col Bars
4 - 16x16 Grid
5 - 32x32 Grid
6 - Burst
7 - 75% Col bars
8 - 50% Gray
9 - Gray Steps 1
10 - Gray Steps 2
11 - White
12 - Black
13 - Red
14 - Green
15 - Blue
•
•
•
•
Query Format: OTPT -o (output) -?
Query Response: OTPT -o (output) - t (type) --min 1 -- max 15
List Format: OTPT -o (output) --list
List Response: 1:"H Ramp"
2:" V Ramp"
3:"100% Col Bars"
4:"16x16 Grid"
5:"32x32 Grid"
6:"Burst"
7:"75% Col bars"
8:"50% Gray"
9:"Gray Steps 1"
10:"Gray Steps 2"
11:"White"
150
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
12:"Black"
13:"Red"
14:"Green"
15:"Blue"
póëíÉã=`çãã~åÇë
^rql`cd=
• Description: Auto Input Configuration Mode
• Command Format: AUTOCFG -m (mode)
• Parameters: -m (mode): 0 - off, 1 - on (default: off)
• Query Format: AUTOCFG -?
• Query Response: AUTOCFG -m (mode) --min 0 -- max 1
^rqlp^sb=
• Description: Auto Input Settings Save
• Command Format: AUTOSAVE -m (mode)
• Parameters: -m (mode): 0 - off, 1 - on (default: off)
• Query Format: AUTOSAVE -?
• Query Response: AUTOSAVE -m (mode) --min 0 -- max 1
^rqlq^hb=
• Description: Auto Take Mode
• Command Format: AUTOTAKE -m (mode)
• Parameters: -m (mode): 0 - off, 1 - on (default: off)
• Query Format: AUTOTAKE -?
• Query Response: AUTOTAKE -m (mode) --min 0 -- max 1
_ihqo^k=
• Description:
Sets whether going to black is a direct transition or requires a
TAKE.
•
•
Command Format: BLKTRAN -m (mode)
•
•
Query Format: BLKTRAN -?
Parameters: -m (mode): 0 - do an immediate transition, 1 - take is required
(Default: off)
Query Response: BLKTRAN -m (mode) --min 0 -- max 1
`lkqbuq=
• Description: Sets menu context
• Command Format: CONTEXT -m (mode)
DCS-200 • User’s Guide
151
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
•
•
af^d
•
•
•
•
•
af^da
•
•
•
•
•
fpq^q
•
•
•
i`io
•
•
•
•
•
iajm
•
•
•
•
•
152
Parameters: -m (mode): 0 - off, 1 - on
Query Format: CONTEXT -?
Query Response: CONTEXT -m (mode) --min 0 -- max 1
Description: Performs a system diagnostic test. The results are logged into a file
which may be displayed using DIAGD.
Command Format: DIAG
Parameters: None
Query Format: N/A
Query Response: N/A
Description: Display the results of the last performed system diagnostic test.
Command Format: DIAGD
Parameters: None
Query Format: N/A
Query Response: N/A
Description: Query only command for the input status type and format.
Query Format: ISTAT -?
Query Response: ISTAT -t "(input type)" -f "(input format)"
Description: Clear the selected log (ram copy, not flash).
Command Format: LCLR -l (log)
Parameters: -l (log): 0-combined, 1-debug, 2-warning, 3-error
Query Format: N/A
Query Response: N/A
Description: Display the current log messages (ram copy, not flash) for the
selected log.
Command Format: LDMP -l (log)
Parameters: -l (log): 0-combined, 1-debug, 2-warning, 3-error
Query Format: N/A
Query Response: N/A
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
icbk
•
•
•
Description: Sets the mode for the selected log. When selected, the messages
for that log will be written to flash every time interval specified in (LINT).
Command Format: LFEN -l (log) -m (mode)
Parameters: - l (log): 0-combined, 1-debug, 2-warning, 3-error
-m (mode): 0 - disable, 1 - enable
•
•
ifkq
•
•
•
•
•
Query Format: N/A
Query Response: N/A
Description: Sets the time interval for writing the enabled logs to flash.
Command Format: LINT -t (time interval)
Parameters: -t (time interval): 1 - 60 seconds
Query Format: N/A
Query Response: N/A
il`hlrq
• Description:
Controls the lockout mode of the front panel. With full lockout mode
enabled, all keys and menu will be deactivated. The executive mode will lock out
all but the input bus keys (1 through 8, SDI, and LOGO).
•
•
Command Format: LOCKOUT -m (mode) -f
Parameters: -m (mode): 0 - disable, 1 - full lockout, 2 - executive mode
(default: 0 - disable)
-f: Command from front panel
•
•
lpq^q
•
•
•
Query Format: LOCKOUT -?
Query Response: LOCKOUT -m (mode) -- min 0 -- max 2
Description: Query only command for the output status type and format.
Query Format: OSTAT -?
Query Response: OSTAT -t "(output type)" -f "(output format)"
mobsfbt=
• Description:
Query only command for the input, key and black button status on
preview. If the black, key, or scaler path is not present on preview, then these
options are not returned.
•
Parameters: -i (input): 1 - 9
-k: key on preview
-b: black on preview
-l: logo on preview
-a: A or B path of scaler input on preview
DCS-200 • User’s Guide
153
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
•
Query Format: PREVIEW -?
Query Response: PREVIEW -i(input) -k -b
moldo^j=
• Description:
Query only command for the input, key and black button status on
program. If the black, key, or scaler path is not present on program, then these
options are not returned.
•
Parameters: -i (input): 1 - 9
-k: key on preview
-b: black on preview
-l: logo on preview
-a: A or B path of scaler input on preview
•
•
obpbq
•
•
•
Query Format: PROGRAM -?
Query Response: PROGRAM -i(input) -k -b
Description: Reset unit
Command Format: RESET [-f | -s ]
Parameters:
-f : factory reset
or
-s: soft reset
•
•
p^sb=
•
•
•
•
•
Query Format: N/A
Query Response: N/A
Description: System Save
Command Format: SAVE
Parameters: N/A
Query Format: N/A
Query Response: N/A
pbof^i=
• Description: Sets the serial port.
• Command Format: SERIAL -b (baud) -p (parity/etc.) -h (handshaking)
• Parameters: -b (baud): 0 - 9600, 1 - 38400, 2 - 57600, 3 - 115200 (default:
115200)
-p (parity/etc): 0 - N81, 1 - E71, 2 - O71, 3 - E72, 4 - O72 (default: N81)
-h (handshaking): 0 - off, 1 - on (default: on)
•
154
Query Format: SERIAL -? - (option letter)
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
The SERIAL query will return only one option parameter at a time. If no
option is specified, an error code will be returned.
•
Query Response: SERIAL -b (baud) --min 0 -- max 3
SERIAL -p (parity/etc) --min 0 -max 4
SERIAL -h (handshaking) --min 0 -max 1
qbjm
•
•
•
Description: Query only command for the temperature of the unit.
Query Format: TEMP -?
Query Response: TEMP -c (celsius) -f (fahrenheit)
qokqfjb=
• Description: Set transition time
• Command Format: TRNTIME -s (seconds)
• Parameters: -s (seconds): 1.5 - 5.0 (default: 1.5)
• Query Format: TRNTIME -?
• Query Response: TRNTIME -s (seconds) --min 1.5 -- max 5
sbo
•
•
•
•
•
Description: Display Version info
Command Format: VER
Parameters: N/A
Query Format: N/A
Query Response: N/A
sca_oq=
• Description: Set VFD brightness
• Command Format: VFDBRT -b (brightness) -f
• Parameters:
-b (brightness): 1 - 16 (default: 10)
-f: Command from front panel
•
•
Query Format: VFDBRT -?
Query Response: VFDBRT -b (brightness) --min 1 -- max 16
hÉó=`çãã~åÇë
ihbv=
•
•
DCS-200 • User’s Guide
Description: Luminance Key definition
Command Format: LKEY -m (mode) -s (source) -c (clip) -g (gain) -o (opacity) -h
(hoffset) -v (v offset)
155
_K==oÉãçíÉ=`çåíêçä
Remote Commands
•
Command Params:
-m mode: 0-off, 1-on (Default: off)
-s source: 1-6 (analog) 7-8 (DVI), 9-SDI
-c clip: 0 - 1023 (default: 0)
-g gain: 0 - 1023.99 (default: 1.00)
-o opacity: 0-1023 (default: 1023)
-h hoffset: +/- ½ (input hact - output hact)
-v voffset: +/- ½ (input vact - output vact)
•
Query Format: LKEY -? -(option letter)
The LKEY query will return only one option parameter at a time. If no
option is specified, an error code will be returned.
•
Query Response: LKEY -m (mode) --min 0 --max 1
LKEY -s (source) --min 0 --max 11
LKEY -c (clip) --min 0 --max 1023
LKEY -g (gain) --min 0 --max 1023.99
LKEY -o (opacity) --min 0 --max 1023
LKEY -h (hoffset) --min (hoffset min) -max (hoffset max)
LKEY -v (voffset) --min (voffset min) -max (voffset max)
•
List Format: LKEY --list
The list command for LKEY returns the possible values for the source
parameter.
•
List Response: 1:"1"
2:" 2"
3:"3"
4:"4"
5:"5"
6:"6"
7:"7"
8:"8"
9:"SDI"
ildl=`çãã~åÇë
ildlabi=
• Description: Delete the selected logo file.
• Command Format: LOGODEL -l (logo)
• Command Params: -l logo: 1 - 3 (Default: 1)
• Query Format: N/A
• Query Response: N/A
156
DCS-200 • User’s Guide
_K==oÉãçíÉ=`çåíêçä
Remote Commands
ildlp^sb=
• Description:
Save the image on Program output to the selected logo frame store
and file.
•
•
•
•
Command Format: LOGOSAVE -l (logo)
Command Params: -l logo: 1 - 3 (Default: 1)
Query Format: N/A
Query Response: N/A
ildlpbi=
• Description: Logo selection
• Command Format: LOGOSEL -l (logo)
• Command Params: -l logo: 1 - LOGO1, 2 - LOGO2, 3 - LOGO3
(Default:
LOGO1)
•
•
•
•
Query Format: LOGOSEL -?
Query Response: LOGOSEL -l (logo) --min 1 --max 3
List Format: LOGOSEL --list
List Response: 1:"LOGO1"
2:"LOGO2"
3:"LOGO3"
ildlpq^q=
• Description: The logo format status. This command is a query only.
• Command Params: -l logo: 1 - LOGO1, 2 - LOGO2, 3 - LOGO3
• Query Format: LOGOSTAT -l (logo) -?
• Query Response: LOGOSTAT -l (logo) -s (status string)
DCS-200 • User’s Guide
157
_K==oÉãçíÉ=`çåíêçä
Remote Commands
158
DCS-200 • User’s Guide
`K==`çåí~Åí=fåÑçêã~íáçå
få=qÜáë=^ééÉåÇáñ
The following topics are discussed in this Appendix:
•
•
•
Warranty
Return Material Authorization (RMA)
Contact Information
t~êê~åíó
All video products are designed and tested to the highest quality standards and are backed
by a full 3-year parts and labor warranty. Warranties are effective upon delivery date to
customer and are non-transferable. Barco warranties are only valid to the original
purchaser/owner. Warranty related repairs include parts and labor, but do not include
faults resulting from user negligence, special modifications, lightning strikes, abuse (drop/
crush), and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair. Barco will cover
shipping charges for return shipments to customers.
oÉíìêå=j~íÉêá~ä=^ìíÜçêáò~íáçå=Eoj^F
In the unlikely event that a product is required to be returned for repair, please call the
following number and ask for a Sales Engineer to receive a Return Merchandise
Authorization number (RMA).
•
(888) 414-7226
RMA Conditions are listed below:
DCS-200 • User’s Guide
a.
Prior to returning any item, you must receive a Return Merchandise
Authorization (RMA) number.
b.
All RMA numbers must appear on their return-shipping label.
c.
RMA numbers are valid for ten (10) days from issue date.
d.
All shipping and insurance charges on all RMAs must be prepaid by the
customer
159
`K==`çåí~Åí=fåÑçêã~íáçå
Contact Information
`çåí~Åí=fåÑçêã~íáçå
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, California 95670
USA
•
•
•
•
Phone: (916) 859-2500
Toll Free: (888) 414-7226
Fax: (916) 859-2515
Website: www.barco.com
Sales Contact Information
•
•
•
Direct: (916) 859-2505
Toll Free: (888) 414-7226
E-mail: folsomsales@barco.com
Barco N.V.
Noordlaan 5
8520 Kuurne
BELGIUM
•
•
•
Phone: +32 56.36.82.11
Fax: +32 56.35.16.51
Website: www.barco.com
Technical Support
•
160
Tech Line: (866) 374-7878 — 24 hours per day, 7 days per week
DCS-200 • User’s Guide
fåÇÉñ
kìãÉêáÅë
10/100BaseT . . . . . . . . . . . . . . . . . . . . . . . . . .26
1-1 Sampling . . . . . . . . . . . . . . . . . . . . . . . . . .58
3-2 film pulldown . . . . . . . . . . . . . . . . . . . . . . .63
^
AC
connector . . . . . . . . . . . . . . . . . . . . . . . . .26
power and voltage selection . . . . . . . . . . .30
power cords . . . . . . . . . . . . . . . . . . . . . . .30
power installation . . . . . . . . . . . . . . . . . . .29
ACQ (command) . . . . . . . . . . . . . . . . . . . . . .135
Acrobat usage . . . . . . . . . . . . . . . . . . . . . . . . .14
navigating and searching . . . . . . . . . . . . .14
Adapter information . . . . . . . . . . . . . . . . . . . . .28
Address
company . . . . . . . . . . . . . . . . . . . . . . . . . . .3
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
MAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
ADJUST
knob . . . . . . . . . . . . . . . . . . . . . . . . . .20, 21
using knob . . . . . . . . . . . . . . . . . . . . . . . .39
Adjust
analog input sources . . . . . . . . . . . . . . . .57
background color . . . . . . . . . . . . . . . . . . .57
brightness . . . . . . . . . . . . . . . . . . . . . . . . .61
color balance . . . . . . . . . . . . . . . . . . . . . .62
colorspace . . . . . . . . . . . . . . . . . . . . . . . .56
contrast . . . . . . . . . . . . . . . . . . . . . . . . . . .61
digital input sources . . . . . . . . . . . . . . . . .60
hue/saturation color balance . . . . . . . . . .62
image . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
input format . . . . . . . . . . . . . . . . . . . . . . .55
input parameters . . . . . . . . . . . . . . . . . . . .60
input type . . . . . . . . . . . . . . . . . . . . . . . . .56
NTSC input sources . . . . . . . . . . . . . . . . .60
output format . . . . . . . . . . . . . . . . . . . . . .48
output gamma . . . . . . . . . . . . . . . . . . . . .49
output sync . . . . . . . . . . . . . . . . . . . . . . . .49
PAL input sources . . . . . . . . . . . . . . . . . . .60
processing . . . . . . . . . . . . . . . . . . . . . . . .63
DCS-200 • User’s Guide
raster box . . . . . . . . . . . . . . . . . . . . . .49, 52
RGB color balance . . . . . . . . . . . . . . . . . .62
sample phase . . . . . . . . . . . . . . . . . . . . . .59
test pattern . . . . . . . . . . . . . . . . . . . . . . . .48
timing . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
transition time . . . . . . . . . . . . . . . . . . . . . .47
VFD brightness . . . . . . . . . . . . . . . . . . . . .73
Adjust On . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Agency specifications . . . . . . . . . . . . . . . . . . 117
Analog
15-pin D connector pinouts . . . . . . . . . . 118
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
output . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
sync . . . . . . . . . . . . . . . . . . . . . . . . . .49, 53
Application questions . . . . . . . . . . . . . . . . . . . .18
Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . .61
Asterisks . . . . . . . . . . . . . . . . . . . . . . . . . .44, 55
Auto
black, take . . . . . . . . . . . . . . . . . . . . . . . .72
config . . . . . . . . . . . . . . . . . . . . . . . . .58, 60
input config . . . . . . . . . . . . . . . . . . . . . . . .71
input save . . . . . . . . . . . . . . . . . . . . . . . . .72
key, take . . . . . . . . . . . . . . . . . . . . . . . . . .72
sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
take . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Auto acquire
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
understanding . . . . . . . . . . . . . . . . . . . . . .86
Auto take
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
off, black . . . . . . . . . . . . . . . . . . . . . . . . . .93
off, key . . . . . . . . . . . . . . . . . . . . . . . . . . .96
on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
on, black . . . . . . . . . . . . . . . . . . . . . . . . . .94
on, key . . . . . . . . . . . . . . . . . . . . . . . . . . .97
AUTOACQ (command) . . . . . . . . . . . . . . . . .135
AUTOCFG (command) . . . . . . . . . . . . . . . . .151
AUTOSAVE (command) . . . . . . . . . . . . . . . .151
AUTOTAKE (command) . . . . . . . . . . . . . . . .151
_
BACKGND (command) . . . . . . . . . . . . . . . . .136
161
Index
Background color, adjust . . . . . . . . . . . . . . . . .57
Barco
contact information . . . . . . . . . . . . . . . . .160
sales contact information . . . . . . . . . . . .160
technical support information . . . . . . .3, 160
warranty . . . . . . . . . . . . . . . . . . . . . . . . .159
Baud . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Best guess format . . . . . . . . . . . . . . . . . . . . . .55
Black
auto take . . . . . . . . . . . . . . . . . . . . . . . . . .72
auto take off . . . . . . . . . . . . . . . . . . . . . . .93
auto take on . . . . . . . . . . . . . . . . . . . . . . .94
background . . . . . . . . . . . . . . . . . . . . . . . .57
button . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
BLACK (command) . . . . . . . . . . . . . . . . . . . .147
Black Auto Take
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Blinking (button) . . . . . . . . . . . . . . . . . . . . .22, 35
BLK, using . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
BLKTRAN (command) . . . . . . . . . . . . . . . . . .151
BLKVID (command) . . . . . . . . . . . . . . . . . . . .136
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . .18
BNC breakout cable . . . . . . . . . . . . . . . . . . . .32
Brackets . . . . . . . . . . . . . . . . . . . . . . . .40, 44, 55
Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
VFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Button
BLACK . . . . . . . . . . . . . . . . . . . . . . . . . . .23
FRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
states . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
TAKE . . . . . . . . . . . . . . . . . . . . . . . . .20, 24
Button state
blinking . . . . . . . . . . . . . . . . . . . . . . . .22, 35
lit solid . . . . . . . . . . . . . . . . . . . . . . . .22, 35
off . . . . . . . . . . . . . . . . . . . . . . . . . . . .22, 35
`
Cable
equalization . . . . . . . . . . . . . . . . . . . . . . .79
information . . . . . . . . . . . . . . . . . . . . . . . .28
CBLEQ (command) . . . . . . . . . . . . . . . . . . . .136
Change history . . . . . . . . . . . . . . . . . . . . . . . . .6
Chapter structure . . . . . . . . . . . . . . . . . . . . . . .13
Chassis internal temperature . . . . . . . . . . . . . .80
Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Color
background . . . . . . . . . . . . . . . . . . . . . . . .57
balance . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Colorspace . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
162
Command
ACQ . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
AUTOACQ . . . . . . . . . . . . . . . . . . . . . . .135
AUTOCFG . . . . . . . . . . . . . . . . . . . . . . .151
AUTOSAVE . . . . . . . . . . . . . . . . . . . . . .151
AUTOTAKE . . . . . . . . . . . . . . . . . . . . . .151
BACKGND . . . . . . . . . . . . . . . . . . . . . . .136
BLACK . . . . . . . . . . . . . . . . . . . . . . . . . .147
BLKTRAN . . . . . . . . . . . . . . . . . . . . . . . .151
BLKVID . . . . . . . . . . . . . . . . . . . . . . . . . .136
CBLEQ . . . . . . . . . . . . . . . . . . . . . . . . . .136
CONTEXT . . . . . . . . . . . . . . . . . . . . . . .151
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . .134
DIAG . . . . . . . . . . . . . . . . . . . . . . . . . . . .152
DIAGD . . . . . . . . . . . . . . . . . . . . . . . . . .152
EDID . . . . . . . . . . . . . . . . . . . . . . . . . . . .136
EDIDTYPE . . . . . . . . . . . . . . . . . . . . . . .137
EMAC . . . . . . . . . . . . . . . . . . . . . . . . . . .134
FREEZE . . . . . . . . . . . . . . . . . . . . . . . . .137
GATEWAY . . . . . . . . . . . . . . . . . . . . . . .135
IADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
IAR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
IAUTOC . . . . . . . . . . . . . . . . . . . . . . . . .138
IAVAIL . . . . . . . . . . . . . . . . . . . . . . . . . . .138
IBRT . . . . . . . . . . . . . . . . . . . . . . . . . . . .138
ICDEL . . . . . . . . . . . . . . . . . . . . . . . . . . .139
ICNT . . . . . . . . . . . . . . . . . . . . . . . . . . . .139
ICPHO . . . . . . . . . . . . . . . . . . . . . . . . . .139
ICREC . . . . . . . . . . . . . . . . . . . . . . . . . .139
ICRST . . . . . . . . . . . . . . . . . . . . . . . . . . .140
ICSAV . . . . . . . . . . . . . . . . . . . . . . . . . . .140
ICSP . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
IHATV . . . . . . . . . . . . . . . . . . . . . . . . . . .140
IHCROP . . . . . . . . . . . . . . . . . . . . . . . . .141
IHPAN . . . . . . . . . . . . . . . . . . . . . . . . . . .141
IHPOS . . . . . . . . . . . . . . . . . . . . . . . . . .141
IHTOTAL . . . . . . . . . . . . . . . . . . . . . . . . .142
IHUE . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
IMAP . . . . . . . . . . . . . . . . . . . . . . . . . . . .142
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
IRBRT . . . . . . . . . . . . . . . . . . . . . . . . . . .142
IRCNT . . . . . . . . . . . . . . . . . . . . . . . . . .143
IRES . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
ISAT . . . . . . . . . . . . . . . . . . . . . . . . . . . .143
ISEL . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
ISLICE . . . . . . . . . . . . . . . . . . . . . . . . . .144
ISMP . . . . . . . . . . . . . . . . . . . . . . . . . . . .144
ISTAT . . . . . . . . . . . . . . . . . . . . . . . . . . .152
ISYNC . . . . . . . . . . . . . . . . . . . . . . . . . .145
ITYPE . . . . . . . . . . . . . . . . . . . . . . . . . . .145
IVATV . . . . . . . . . . . . . . . . . . . . . . . . . . .146
IVCROP . . . . . . . . . . . . . . . . . . . . . . . . .146
IVPAN . . . . . . . . . . . . . . . . . . . . . . . . . . .146
IVPOS . . . . . . . . . . . . . . . . . . . . . . . . . .146
IVTOTAL . . . . . . . . . . . . . . . . . . . . . . . . .147
LCLR . . . . . . . . . . . . . . . . . . . . . . . . . . .152
LDMP . . . . . . . . . . . . . . . . . . . . . . . . . . .152
DCS-200 • User’s Guide
Index
LFEN . . . . . . . . . . . . . . . . . . . . . . . . . . .153
LINT . . . . . . . . . . . . . . . . . . . . . . . . . . . .153
LKEY . . . . . . . . . . . . . . . . . . . . . . . . . . .155
LOCKOUT . . . . . . . . . . . . . . . . . . . . . . .153
LOGODEL . . . . . . . . . . . . . . . . . . . . . . .156
LOGOSAVE . . . . . . . . . . . . . . . . . . . . . .157
LOGOSEL . . . . . . . . . . . . . . . . . . . . . . .157
LOGOSTAT . . . . . . . . . . . . . . . . . . . . . .157
OAVAIL . . . . . . . . . . . . . . . . . . . . . . . . . .147
OCSAV . . . . . . . . . . . . . . . . . . . . . . . . . .147
OGM . . . . . . . . . . . . . . . . . . . . . . . . . . . .148
ORBM . . . . . . . . . . . . . . . . . . . . . . . . . . .148
ORES . . . . . . . . . . . . . . . . . . . . . . . . . . .148
OSRC . . . . . . . . . . . . . . . . . . . . . . . . . . .149
OSTAT . . . . . . . . . . . . . . . . . . . . . . . . . .153
OSYNC . . . . . . . . . . . . . . . . . . . . . . . . . .149
OTPM . . . . . . . . . . . . . . . . . . . . . . . . . . .149
OTPT . . . . . . . . . . . . . . . . . . . . . . . . . . .150
PCOMP . . . . . . . . . . . . . . . . . . . . . . . . .147
PREVIEW . . . . . . . . . . . . . . . . . . . . . . . .153
PROGRAM . . . . . . . . . . . . . . . . . . . . . . .154
protocol . . . . . . . . . . . . . . . . . . . . . . . . . .128
remote . . . . . . . . . . . . . . . . . . . . . . . . . .134
RESET . . . . . . . . . . . . . . . . . . . . . . . . . .154
responses . . . . . . . . . . . . . . . . . . . . . . . .128
SAVE . . . . . . . . . . . . . . . . . . . . . . . . . . .154
SERIAL . . . . . . . . . . . . . . . . . . . . . . . . . .154
SUBNET . . . . . . . . . . . . . . . . . . . . . . . . .135
TAKE . . . . . . . . . . . . . . . . . . . . . . . . . . .147
TEMP . . . . . . . . . . . . . . . . . . . . . . . . . . .155
TRNTIME . . . . . . . . . . . . . . . . . . . . . . . .155
VER . . . . . . . . . . . . . . . . . . . . . . . . . . . .155
VFDBRT . . . . . . . . . . . . . . . . . . . . . . . . .155
Command list . . . . . . . . . . . . . . . . . . . . . . . . .131
Communicating with DCS-200 . . . . . . . . . . . .127
Communications
connections . . . . . . . . . . . . . . . . . . . . . . .32
specifications . . . . . . . . . . . . . . . . . . . . . 117
Company address . . . . . . . . . . . . . . . . . . . . . . .3
Components, front panel . . . . . . . . . . . . . . . . .20
Config
network . . . . . . . . . . . . . . . . . . . . . . . . . . .74
save system . . . . . . . . . . . . . . . . . . . . . . .81
Configuration
delete input . . . . . . . . . . . . . . . . . . . . . . . .65
recall input . . . . . . . . . . . . . . . . . . . . . . . .66
reset input . . . . . . . . . . . . . . . . . . . . . . . . .64
save input . . . . . . . . . . . . . . . . . . . . . . . . .64
save output . . . . . . . . . . . . . . . . . . . . . . . .49
configuration files . . . . . . . . . . . . . . . . . . . . . . .70
Configuration files, selecting . . . . . . . . . . .79–80
Connection, format table . . . . . . . . . . . . . . . . .32
Connectivity diagram . . . . . . . . . . . . . . . . . . . .18
Connector
AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
analog 15-pin D pinouts . . . . . . . . . . . . . 118
DVI-I pinouts . . . . . . . . . . . . . . . . . . . . . . 119
DCS-200 • User’s Guide
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . .26
Ethernet pinouts . . . . . . . . . . . . . . . . . . .120
rear panel . . . . . . . . . . . . . . . . . . . . . . . . .25
Contact information . . . . . . . . . . . . . . . . . . . .160
CONTEXT (command) . . . . . . . . . . . . . . . . .151
Context, menu . . . . . . . . . . . . . . . . . . . . . . . . .72
Contrast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
Control overview . . . . . . . . . . . . . . . . . . . . . . .34
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . .14
menu system . . . . . . . . . . . . . . . . . . . . . .39
status menu . . . . . . . . . . . . . . . . . . . . . . .44
Copy protection . . . . . . . . . . . . . . . . . . . . . . . .17
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
CSync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
navigation . . . . . . . . . . . . . . . . . . . . . . . . .39
Custom aspect ratio . . . . . . . . . . . . . . . . . . . . .61
a
Data bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
DCS-200
block diagram . . . . . . . . . . . . . . . . . . . . . .18
button states . . . . . . . . . . . . . . . . . . . . . . .35
command list . . . . . . . . . . . . . . . . . . . . .131
communicating with . . . . . . . . . . . . . . . .127
communications connections . . . . . . . . . .32
connectivity diagram . . . . . . . . . . . . . . . . .18
control overview . . . . . . . . . . . . . . . . . . . .34
features . . . . . . . . . . . . . . . . . . . . . . . . . .15
front panel . . . . . . . . . . . . . . . . . . . . . . . .20
GUI connection and launch . . . . . . . . . .104
GUI connections . . . . . . . . . . . . . . . . . . . .32
GUI operation . . . . . . . . . . . . . . . . . . . . .103
hardware installation . . . . . . . . . . . . . . . .27
hardware orientation . . . . . . . . . . . . . . . . .19
home page . . . . . . . . . . . . . . . . . . . 105, 111
input connections . . . . . . . . . . . . . . . . . . .31
introduction to . . . . . . . . . . . . . . . . . . . . . .13
menu tree . . . . . . . . . . . . . . . . . . . . . . . . .38
operation . . . . . . . . . . . . . . . . . . . . . . . . .33
output connections . . . . . . . . . . . . . . . . . .31
rear panel connectors . . . . . . . . . . . . . . . .25
remote commands . . . . . . . . . . . . . . . . .134
remote control protocol . . . . . . . . . . . . . .127
restart . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
specifications . . . . . . . . . . . . . . . . . . . . . 115
system diagram . . . . . . . . . . . . . . . . . . . .31
upgrading software . . . . . . . . . . . . . . . . .107
Delete
input configuration . . . . . . . . . . . . . . . . . .65
LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . .74, 134
server . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
DHCP (command) . . . . . . . . . . . . . . . . . . . . .134
163
Index
DIAG (command) . . . . . . . . . . . . . . . . . . . . . .152
DIAGD (command) . . . . . . . . . . . . . . . . . . . .152
Diagnostics menu . . . . . . . . . . . . . . . . . . . . . .81
Diagram
connectivity . . . . . . . . . . . . . . . . . . . . . . . .18
system . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
brightness . . . . . . . . . . . . . . . . . . . . . . . . .73
section . . . . . . . . . . . . . . . . . . . . . . . .20, 21
Documentation conventions and symbols . . . .14
Double arrow . . . . . . . . . . . . . . . . . . . . . . . . . .21
Download software . . . . . . . . . . . . . . . . . . . .109
via FTP site . . . . . . . . . . . . . . . . . . . . . .109
via web site . . . . . . . . . . . . . . . . . . . . . . .109
DVI
cable equalization . . . . . . . . . . . . . . . . . . .79
cable equalizer menu . . . . . . . . . . . . . . . .79
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
output . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
sync . . . . . . . . . . . . . . . . . . . . . . . . . .49, 53
DVI-I
connector pinouts . . . . . . . . . . . . . . . . . . 119
connectors . . . . . . . . . . . . . . . . . . . . . . . .25
b
EDID
format . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
setup menu . . . . . . . . . . . . . . . . . . . . . . . .77
type (7, 8) . . . . . . . . . . . . . . . . . . . . . . . . .78
EDID (command) . . . . . . . . . . . . . . . . . . . . . .136
EDIDTYPE (command) . . . . . . . . . . . . . . . . .137
Edit cursor . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Effects section . . . . . . . . . . . . . . . . . . . . . .20, 23
Electrical specifications . . . . . . . . . . . . . . . . . 117
EMAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . .79
set to default . . . . . . . . . . . . . . . . . . . . . . .79
set to maximum . . . . . . . . . . . . . . . . . . . .79
set to minimum . . . . . . . . . . . . . . . . . . . . .79
Equipment marking terms . . . . . . . . . . . . . . . . .5
Error codes . . . . . . . . . . . . . . . . . . . . . . . . . .130
general failures . . . . . . . . . . . . . . . . . . . .130
no error . . . . . . . . . . . . . . . . . . . . . . . . . .130
ESC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
using . . . . . . . . . . . . . . . . . . . . . . . . . .39, 40
Ethernet
address . . . . . . . . . . . . . . . . . . . . . . . . . . .74
connection . . . . . . . . . . . . . . . . . . . . . . . .32
connector . . . . . . . . . . . . . . . . . . . . . . . . .26
connector pinouts . . . . . . . . . . . . . . . . . .120
Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
troubleshoot connection . . . . . . . . . . . . . 113
Executive lockout mode . . . . . . . . . . . . . . . . .101
164
Extended Display Identification Data . . . . . . . .77
c
Factory
default . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
reset menu . . . . . . . . . . . . . . . . . . . . . . . .82
Fade
to black from source plus key . . . . . . . . .100
up to source plus key . . . . . . . . . . . . . . .100
FCC statement . . . . . . . . . . . . . . . . . . . . . . . . .2
Features, DCS-200 . . . . . . . . . . . . . . . . . . . . .15
File Association
menu . . . . . . . . . . . . . . . . . . . . . . . . .16, 79
Flip-flop mode . . . . . . . . . . . . . . . . . . . . . . . . .85
Format
asterisks . . . . . . . . . . . . . . . . . . . . . . . . . .55
best guess . . . . . . . . . . . . . . . . . . . . . . . .55
brackets . . . . . . . . . . . . . . . . . . . . . . . . . .55
connection table . . . . . . . . . . . . . . . . . . . .32
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
output . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
FREEZE (command) . . . . . . . . . . . . . . . . . . .137
Front panel
components . . . . . . . . . . . . . . . . . . . . . . .20
display section . . . . . . . . . . . . . . . . . . . . .20
executive lockout mode . . . . . . . . . . . . .101
full lockout mode . . . . . . . . . . . . . . . . . .101
FRZ
button . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
FTP site . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
Full lockout mode . . . . . . . . . . . . . . . . . . . . .101
Function, quick reference table . . . . . . . . . . . .41
d
Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Gamma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Gateway
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
GATEWAY (command) . . . . . . . . . . . . . . . . .135
Gray background . . . . . . . . . . . . . . . . . . . . . . .57
Guarantee and compensation . . . . . . . . . . . . . .2
GUI
connection and launch . . . . . . . . . . . . . .104
connections . . . . . . . . . . . . . . . . . . . . . . .32
differences from physical control panel .106
how to connect and launch . . . . . . . . . . .104
operation . . . . . . . . . . . . . . . . . . . . . . . .103
DCS-200 • User’s Guide
Index
operations . . . . . . . . . . . . . . . . . . . . . . . .106
similarities to physical control panel . . . .106
status menu . . . . . . . . . . . . . . . . . . . . . .105
up/down arrows . . . . . . . . . . . . . . . . . . .106
web-based . . . . . . . . . . . . . . . . . . . . . . . .16
use the setup menu . . . . . . . . . . . . . . . . .46
use this guide . . . . . . . . . . . . . . . . . . . . . .14
Hue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Hue/Saturation color balance menu . . . . . . . .62
Hyperlinks . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
e
f
H
IADJ (command) . . . . . . . . . . . . . . . . . . . . . .137
IAR (command) . . . . . . . . . . . . . . . . . . . . . . .137
IAUTOC (command) . . . . . . . . . . . . . . . . . . .138
IAVAIL (command) . . . . . . . . . . . . . . . . . . . . .138
IBRT (command) . . . . . . . . . . . . . . . . . . . . . .138
ICDEL (command) . . . . . . . . . . . . . . . . . . . . .139
ICNT (command) . . . . . . . . . . . . . . . . . . . . . .139
ICPHO (command) . . . . . . . . . . . . . . . . . . . .139
ICREC (command) . . . . . . . . . . . . . . . . . . . .139
ICRST (command) . . . . . . . . . . . . . . . . . . . . .140
ICSAV (command) . . . . . . . . . . . . . . . . . . . . .140
ICSP (command) . . . . . . . . . . . . . . . . . . . . . .140
IHATV (command) . . . . . . . . . . . . . . . . . . . . .140
IHCROP (command) . . . . . . . . . . . . . . . . . . .141
IHPAN (command) . . . . . . . . . . . . . . . . . . . . .141
IHPOS (command) . . . . . . . . . . . . . . . . . . . .141
IHTOTAL (command) . . . . . . . . . . . . . . . . . . .142
IHUE (command) . . . . . . . . . . . . . . . . . . . . . .142
Image adjust menu . . . . . . . . . . . . . . . . . . . . .60
IMAP (command) . . . . . . . . . . . . . . . . . . . . . .142
In Auto Acquire . . . . . . . . . . . . . . . . . . . . .55, 70
Information, cables and adapters . . . . . . . . . .28
Input
auto config . . . . . . . . . . . . . . . . . . . . . . . .71
auto save . . . . . . . . . . . . . . . . . . . . . . . . .72
buttons . . . . . . . . . . . . . . . . . . . . . . . . . . .22
colorspace . . . . . . . . . . . . . . . . . . . . . . . .56
configuration file . . . . . . . . . . . . . . . . . . . .63
connections . . . . . . . . . . . . . . . . . . . . . . .31
delete configuration . . . . . . . . . . . . . . . . .65
DVI cable equalizer . . . . . . . . . . . . . . . . .79
format . . . . . . . . . . . . . . . . . . . . . . . . .44, 55
format table . . . . . . . . . . . . . . . . . . . . . .122
format, next . . . . . . . . . . . . . . . . . . . . . . .45
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
previewing . . . . . . . . . . . . . . . . . . . . . . . .50
processing . . . . . . . . . . . . . . . . . . . . . . . .63
recall configuration . . . . . . . . . . . . . . . . . .66
reset configuration . . . . . . . . . . . . . . . . . .64
save configuration . . . . . . . . . . . . . . . . . .64
SDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
selection rules . . . . . . . . . . . . . . . . . . . . .84
source, key . . . . . . . . . . . . . . . . . . . . . . . .68
specifications . . . . . . . . . . . . . . . . . . . . . 116
type . . . . . . . . . . . . . . . . . . . . . . . . . . .44, 56
type, next . . . . . . . . . . . . . . . . . . . . . . . . .45
Inputs
analog . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
active . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
position . . . . . . . . . . . . . . . . . . . . . . . . . . .59
size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . .76
Hardware
installation . . . . . . . . . . . . . . . . . . . . . . . . .27
orientation . . . . . . . . . . . . . . . . . . . . . . . . .19
requirements, upgrading software . . . . .108
HD-15 connectors . . . . . . . . . . . . . . . . . . . . . .25
HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
compliant device . . . . . . . . . . . . . . . . . . . .17
compliant monitor . . . . . . . . . . . . . . . . . . .86
protocol . . . . . . . . . . . . . . . . . . . . . . . . . . .15
repeater . . . . . . . . . . . . . . . . . . . . . . .17, 45
status . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
High-Bandwidth Digital Content Protection . . .17
History, change . . . . . . . . . . . . . . . . . . . . . . . . .6
Horizontal active area . . . . . . . . . . . . . . . . . . .59
How hot is my system . . . . . . . . . . . . . . . . . . .80
How to
adjust sample phase . . . . . . . . . . . . . . . .59
capture and store a LOGO . . . . . . . . . . . .89
communicate with DCS-200 . . . . . . . . . .127
connect and launch the GUI . . . . . . . . . .104
delete configuration files . . . . . . . . . . . . . .66
download software from FTP site . . . . . .109
download software from website . . . . . .109
edit IP address . . . . . . . . . . . . . . . . . . . . .75
enable/disable executive lockout . . . . . .102
freeze and un-freeze an input . . . . . . . . .92
install power . . . . . . . . . . . . . . . . . . . . . . .29
install signals to/from DCS-200 . . . . . . . .31
lock/unlock front panel . . . . . . . . . . . . . .101
power up . . . . . . . . . . . . . . . . . . . . . . . . . .34
transition inputs to Program . . . . . . . . . . .84
transition to a saved logo . . . . . . . . . . . . .90
transition to/from black, auto take off . . . .93
transition to/from black, auto take on . . . .94
transition to/from key, auto take off . . . . . .96
transition to/from key, auto take on . . . . . .97
troubleshoot Ethernet connection . . . . . . 113
upgrade software via Ethernet . . . . . . . . 110
use menu system . . . . . . . . . . . . . . . . . . .39
DCS-200 • User’s Guide
165
Index
DVI . . . . . . . . . . . . . . . . . . . . . . . . . . .25, 67
protected and unprotected . . . . . . . . . . . .86
section . . . . . . . . . . . . . . . . . . . . .20, 22, 24
source signals . . . . . . . . . . . . . . . . . . . . .15
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Installation
hardware . . . . . . . . . . . . . . . . . . . . . . . . .27
power . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
rack mount . . . . . . . . . . . . . . . . . . . . . . . .29
safety precautions . . . . . . . . . . . . . . . . . .28
signals . . . . . . . . . . . . . . . . . . . . . . . . . . .31
site preparation . . . . . . . . . . . . . . . . . . . . .28
unpacking and inspection . . . . . . . . . . . . .28
Introduction to
DCS-200 . . . . . . . . . . . . . . . . . . . . . . . . . .13
keying . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Invalid signal . . . . . . . . . . . . . . . . . . . . . . .55, 71
IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .135
address . . . . . . . . . . . . . . . . . . . . . . . .74, 75
address, port 23 (Telnet) . . . . . . . . . . . .127
IRBRT (command) . . . . . . . . . . . . . . . . . . . . .142
IRCNT (command) . . . . . . . . . . . . . . . . . . . . .143
IRES (command) . . . . . . . . . . . . . . . . . . . . . .143
ISAT (command) . . . . . . . . . . . . . . . . . . . . . .143
ISEL (command) . . . . . . . . . . . . . . . . . . . . . .144
ISLICE (command) . . . . . . . . . . . . . . . . . . . .144
ISMP (command) . . . . . . . . . . . . . . . . . . . . . .144
ISTAT (command) . . . . . . . . . . . . . . . . . . . . .152
ISYNC (command) . . . . . . . . . . . . . . . . . . . . .145
ITYPE (command) . . . . . . . . . . . . . . . . . . . . .145
IVATV (command) . . . . . . . . . . . . . . . . . . . . .146
IVCROP (command) . . . . . . . . . . . . . . . . . . .146
IVPAN (command) . . . . . . . . . . . . . . . . . . . . .146
IVPOS (command) . . . . . . . . . . . . . . . . . . . .146
IVTOTAL (command) . . . . . . . . . . . . . . . . . . .147
h
Key
auto take . . . . . . . . . . . . . . . . . . . . . . . . . .72
auto take off . . . . . . . . . . . . . . . . . . . . . . .96
auto take on . . . . . . . . . . . . . . . . . . . . . . .97
clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
fade to black from source plus key . . . . .100
fade up to source plus key . . . . . . . . . . .100
gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
H offset . . . . . . . . . . . . . . . . . . . . . . . . . . .68
input source . . . . . . . . . . . . . . . . . . . . . . .68
introduction to . . . . . . . . . . . . . . . . . . . . . .95
luminance . . . . . . . . . . . . . . . . . . . . . .16, 67
mix down . . . . . . . . . . . . . . . . . . . . . . . . .98
mix source plus key down . . . . . . . . . . . .99
mix source plus key up . . . . . . . . . . . . . . .98
mix up . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
opacity . . . . . . . . . . . . . . . . . . . . . . . . . . .68
166
performing . . . . . . . . . . . . . . . . . . . . . . . .96
setup menu . . . . . . . . . . . . . . . . . . . . . . . .67
transition combinations . . . . . . . . . . . . . . .97
transition source under key . . . . . . . . . . .99
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
V offset . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Key Auto Take
off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
KEY button . . . . . . . . . . . . . . . . . . . . . . . . . . .24
i
LCLR (command) . . . . . . . . . . . . . . . . . . . . .152
LDMP (command) . . . . . . . . . . . . . . . . . . . . .152
LFEN (command) . . . . . . . . . . . . . . . . . . . . .153
Line voltage selection . . . . . . . . . . . . . . . . . . .30
LINT (command) . . . . . . . . . . . . . . . . . . . . . .153
List, commands . . . . . . . . . . . . . . . . . . . . . . .131
Lit solid (button) . . . . . . . . . . . . . . . . . . . . .22, 35
LKEY (command) . . . . . . . . . . . . . . . . . . . . .155
Lockout
executive mode . . . . . . . . . . . . . . . . . . .101
LOCKOUT (command) . . . . . . . . . . . . . . . . .153
LOGO
button . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
delete . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
how to capture and store . . . . . . . . . . . . .89
in executive lockout mode . . . . . . . . . . .101
save . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
selection . . . . . . . . . . . . . . . . . . . . . . . . . .69
setup menu . . . . . . . . . . . . . . . . . . . . . . . .69
status . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
transitioning to . . . . . . . . . . . . . . . . . . . . .90
using . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
LOGODEL (command) . . . . . . . . . . . . . . . . .156
LOGOSAVE (command) . . . . . . . . . . . . . . . .157
LOGOSEL (command) . . . . . . . . . . . . . . . . .157
LOGOSTAT (command) . . . . . . . . . . . . . . . .157
Luminance key . . . . . . . . . . . . . . . . . . . . .16, 67
j
MAC Address . . . . . . . . . . . . . . . . . . . . . . . . .76
Macrovision copy protection . . . . . . . . . . . . . .63
Main outputs . . . . . . . . . . . . . . . . . . . . . . . . . .26
Menu
Adjust On . . . . . . . . . . . . . . . . . . . . . . . . .55
context . . . . . . . . . . . . . . . . . . . . . . . .44, 72
diagnostics . . . . . . . . . . . . . . . . . . . . . . . .81
display . . . . . . . . . . . . . . . . . . . . . . . . . . .21
DVI cable equalizer . . . . . . . . . . . . . . . . .79
EDID setup . . . . . . . . . . . . . . . . . . . . . . . .77
Ethernet . . . . . . . . . . . . . . . . . . . . . . . . . .74
DCS-200 • User’s Guide
Index
Executive Mode . . . . . . . . . . . . . . . . . . .102
factory reset . . . . . . . . . . . . . . . . . . . . . . .82
File Association . . . . . . . . . . . . . . . . . . . .70
File Recall . . . . . . . . . . . . . . . . . . . . . .79–80
gateway . . . . . . . . . . . . . . . . . . . . . . . . . .75
GUI status . . . . . . . . . . . . . . . . . . . . . . . .105
hue/saturation color balance . . . . . . . . . .62
image adjust . . . . . . . . . . . . . . . . . . . . . . .60
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
input file association . . . . . . . . . . . . . .16, 79
key setup . . . . . . . . . . . . . . . . . . . . . . . . .67
LOGO setup . . . . . . . . . . . . . . . . . . . . . . .69
netmask . . . . . . . . . . . . . . . . . . . . . . . . . .75
output . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
output sync setup . . . . . . . . . . . . . . . . . . .49
Preview . . . . . . . . . . . . . . . . . . . . . . . . . . .50
RGB color balance . . . . . . . . . . . . . . . . . .62
rules and conventions . . . . . . . . . . . . . . .39
serial setup . . . . . . . . . . . . . . . . . . . . . . . .76
set static IP . . . . . . . . . . . . . . . . . . . . . . . .74
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
status . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Sync Setup . . . . . . . . . . . . . . . . . . . . . . . .52
system . . . . . . . . . . . . . . . . . . . . . . . . . . .73
system temperature . . . . . . . . . . . . . . . . .80
tech support . . . . . . . . . . . . . . . . . . . . . . .82
test pattern . . . . . . . . . . . . . . . . . . . . . . . .48
timing adjust . . . . . . . . . . . . . . . . . . . . . . .57
tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
usage, rules . . . . . . . . . . . . . . . . . . . . . . .39
user preference . . . . . . . . . . . . . . . . . . . .70
value in brackets . . . . . . . . . . . . . . . . . . . .40
Mix
key down . . . . . . . . . . . . . . . . . . . . . . . . .98
key up . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
plus digital key . . . . . . . . . . . . . . . . . . . . .47
source plus key down . . . . . . . . . . . . . . . .99
source plus key up . . . . . . . . . . . . . . . . . .98
Mode
flip-flop . . . . . . . . . . . . . . . . . . . . . . . . . . .85
test pattern . . . . . . . . . . . . . . . . . . . . . . . .48
k
Navigation cursor . . . . . . . . . . . . . . . . . . . .21, 39
Netmask
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Network config . . . . . . . . . . . . . . . . . . . . . . . . .74
l
OAVAIL (command) . . . . . . . . . . . . . . . . . . . .147
OCSAV (command) . . . . . . . . . . . . . . . . . . . .147
DCS-200 • User’s Guide
Off (button) . . . . . . . . . . . . . . . . . . . . . . . .22, 35
Offset
H . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
OGM (command) . . . . . . . . . . . . . . . . . . . . . .148
Opacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
GUI . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
quick setup . . . . . . . . . . . . . . . . . . . . . . . .36
Operators safety summary . . . . . . . . . . . . . . . .4
ORBM (command) . . . . . . . . . . . . . . . . . . . . .148
ORES (command) . . . . . . . . . . . . . . . . . . . . .148
Orientation, hardware . . . . . . . . . . . . . . . . . . .19
OSRC (command) . . . . . . . . . . . . . . . . . . . . .149
OSTAT (command) . . . . . . . . . . . . . . . . . . . .153
OSYNC (command) . . . . . . . . . . . . . . . . . . . .149
OTPM (command) . . . . . . . . . . . . . . . . . . . . .149
OTPT (command) . . . . . . . . . . . . . . . . . . . . .150
Output
analog . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
connections . . . . . . . . . . . . . . . . . . . . . . .31
DVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
format . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
format (Preview) . . . . . . . . . . . . . . . . . . . .51
format table . . . . . . . . . . . . . . . . . . . . . .122
gamma . . . . . . . . . . . . . . . . . . . . . . . . . . .49
main . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
preview . . . . . . . . . . . . . . . . . . . . . . . . . . .26
save configuration . . . . . . . . . . . . . . . . . .49
source selection . . . . . . . . . . . . . . . . . . . .51
specifications . . . . . . . . . . . . . . . . . . . . . 116
sync setup menu . . . . . . . . . . . . . . . . . . .49
test pattern . . . . . . . . . . . . . . . . . . . . . . . .48
Oversample . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Over-temp . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Overview
control . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
software upgrade . . . . . . . . . . . . . . . . . .108
m
Page
DCS-200 home . . . . . . . . . . . . . . . . 105, 111
select file . . . . . . . . . . . . . . . . . . . . . . . . 111
upload status . . . . . . . . . . . . . . . . . . . . . 112
Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
PCOMP (command) . . . . . . . . . . . . . . . . . . .147
PDF file usage . . . . . . . . . . . . . . . . . . . . . . . . .14
navigating and searching . . . . . . . . . . . . .14
Performing a key . . . . . . . . . . . . . . . . . . . . . . .96
Phase A, Phase B . . . . . . . . . . . . . . . . . . . . . .58
Phone, tech support . . . . . . . . . . . . . . . . . . . .82
Physical specifications . . . . . . . . . . . . . . . . . . 117
Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
167
Index
analog 15-pin D connector . . . . . . . . . . . 118
DVI-I connector . . . . . . . . . . . . . . . . . . . 119
Ethernet connector . . . . . . . . . . . . . . . . .120
serial connector . . . . . . . . . . . . . . . . . . .121
Power
cord, line voltage selection . . . . . . . . . . . .30
installation . . . . . . . . . . . . . . . . . . . . . . . . .29
precautions . . . . . . . . . . . . . . . . . . . . . . . .30
up and initialization . . . . . . . . . . . . . . . . . .34
Preview
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
output format . . . . . . . . . . . . . . . . . . . . . .51
output source selection . . . . . . . . . . . . . .51
outputs . . . . . . . . . . . . . . . . . . . . . . . . . . .26
save configuration . . . . . . . . . . . . . . . . . .53
sync setup . . . . . . . . . . . . . . . . . . . . . . . .52
PREVIEW (command) . . . . . . . . . . . . . . . . . .153
Previewing input signals . . . . . . . . . . . . . . . . .50
Processing menu . . . . . . . . . . . . . . . . . . . . . . .63
PROGRAM (command) . . . . . . . . . . . . . . . . .154
Protocol
command . . . . . . . . . . . . . . . . . . . . . . . .128
remote control . . . . . . . . . . . . . . . . . . . .127
Pulldown Compensation . . . . . . . . . . . . . . . . .63
n
Query options . . . . . . . . . . . . . . . . . . . . . . . .128
Quick
function reference . . . . . . . . . . . . . . . . . . .41
setup and operations . . . . . . . . . . . . . . . .36
o
Rack mount installation . . . . . . . . . . . . . . . . . .29
Raster Box . . . . . . . . . . . . . . . . . . . . . . . . .49, 52
Ratio, aspect . . . . . . . . . . . . . . . . . . . . . . . . . .61
Rear panel connectors . . . . . . . . . . . . . . . . . . .25
Recall
input configuration . . . . . . . . . . . . . . . . . .66
Reference, quick function table . . . . . . . . . . . .41
Remote control protocol . . . . . . . . . . . . . . . .127
Repeater, HDCP . . . . . . . . . . . . . . . . . . . .17, 45
RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154
Reset
all . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
config . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
factory . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
input configuration . . . . . . . . . . . . . . . . . .64
serial parameters . . . . . . . . . . . . . . . . . . .76
Resolutions, input and output . . . . . . . . . . . . .15
Restart DCS-200 . . . . . . . . . . . . . . . . . . . . . . 112
Return material authorization . . . . . . . . . . . . .159
RGB color balance menu . . . . . . . . . . . . . . . .62
168
RMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Rules, input selection . . . . . . . . . . . . . . . . . . .84
p
Safety
precautions . . . . . . . . . . . . . . . . . . . . . . . .28
summary . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Sales contact information . . . . . . . . . . . . . . .160
Sample phase, adjust . . . . . . . . . . . . . . . . . . .59
Sampling . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Saturation . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Save
config . . . . . . . . . . . . . . . . . . . . . .49, 64, 81
input configuration . . . . . . . . . . . . . . . . . .64
input, auto . . . . . . . . . . . . . . . . . . . . . . . . .72
LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
output configuration . . . . . . . . . . . . . . . . .49
Preview configuration . . . . . . . . . . . . . . . .53
system config . . . . . . . . . . . . . . . . . . . . . .81
system state . . . . . . . . . . . . . . . . . . . .81, 82
SAVE (command) . . . . . . . . . . . . . . . . . . . . .154
Scaling and de-interlacing . . . . . . . . . . . . . . . .16
SDI
button . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Section
display . . . . . . . . . . . . . . . . . . . . . . . .20, 21
effects . . . . . . . . . . . . . . . . . . . . . . . . .20, 23
inputs . . . . . . . . . . . . . . . . . . . . . .20, 22, 24
SEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
using . . . . . . . . . . . . . . . . . . . . . . . . . .39, 40
Select file page . . . . . . . . . . . . . . . . . . . . . . . 111
Selection, input rules . . . . . . . . . . . . . . . . . . . .84
Serial
communications . . . . . . . . . . . . . . . . . . . .26
connection . . . . . . . . . . . . . . . . . . . . . . . .32
connector . . . . . . . . . . . . . . . . . . . . . . . . .26
connector pinouts . . . . . . . . . . . . . . . . . .121
setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
setup menu . . . . . . . . . . . . . . . . . . . . . . . .76
SERIAL (command) . . . . . . . . . . . . . . . . . . . .154
Set
gateway . . . . . . . . . . . . . . . . . . . . . . . . . .75
netmask . . . . . . . . . . . . . . . . . . . . . . . . . .75
static IP . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Setup
EDID . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
menu, using . . . . . . . . . . . . . . . . . . . . . . .46
serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Signal installation . . . . . . . . . . . . . . . . . . . . . . .31
Site preparation . . . . . . . . . . . . . . . . . . . . . . . .28
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Software
downloading . . . . . . . . . . . . . . . . . . . . . .109
requirements, upgrading . . . . . . . . . . . .108
DCS-200 • User’s Guide
Index
upgrade overview . . . . . . . . . . . . . . . . . .108
upgrade via Ethernet . . . . . . . . . . . . . . . 110
upgrading . . . . . . . . . . . . . . . . . . . . . . . .107
version . . . . . . . . . . . . . . . . . . . . . . . .35, 82
SOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Source transition under key . . . . . . . . . . . . . . .99
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 115
agency . . . . . . . . . . . . . . . . . . . . . . . . . . 117
communications . . . . . . . . . . . . . . . . . . . 117
electrical . . . . . . . . . . . . . . . . . . . . . . . . . 117
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
input and output format table . . . . . . . . .122
output . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
physical . . . . . . . . . . . . . . . . . . . . . . . . . 117
pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Standard mix . . . . . . . . . . . . . . . . . . . . . . . . . .47
Static IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Status
HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
menu, conventions . . . . . . . . . . . . . . . . . .44
menu, input format . . . . . . . . . . . . . . . . . .44
menu, input type . . . . . . . . . . . . . . . . . . . .44
menu, next input format . . . . . . . . . . . . . .45
menu, next input type . . . . . . . . . . . . . . . .45
Status menu, GUI . . . . . . . . . . . . . . . . . . . . .105
Stop bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
SUBNET (command) . . . . . . . . . . . . . . . . . . .135
Support, technical information . . . . . . . . . .3, 160
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Sync
analog . . . . . . . . . . . . . . . . . . . . . . . . .49, 53
auto . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
CSync . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
DVI . . . . . . . . . . . . . . . . . . . . . . . . . . .49, 53
selection . . . . . . . . . . . . . . . . . . . . . . . . . .63
setup (Preview outputs) . . . . . . . . . . . . . .52
setup menu . . . . . . . . . . . . . . . . . . . . . . . .49
slice . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
SOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Sync Setup menu . . . . . . . . . . . . . . . . . . . . . .52
System
config, save . . . . . . . . . . . . . . . . . . . . . . .81
diagram . . . . . . . . . . . . . . . . . . . . . . . . . .31
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
temperature menu . . . . . . . . . . . . . . . . . .80
q
Table
format connections . . . . . . . . . . . . . . . . . .32
input and output formats . . . . . . . . . . . . .122
quick function reference . . . . . . . . . . . . . .41
DCS-200 • User’s Guide
TAKE
button . . . . . . . . . . . . . . . . . . . . . . . . .20, 24
command . . . . . . . . . . . . . . . . . . . . . . . .147
Tech support
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
phone . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
software version . . . . . . . . . . . . . . . . . . . .82
Technical support information . . . . . . . . . .3, 160
Telnet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
using . . . . . . . . . . . . . . . . . . . . . . . . . . . .127
TEMP (command) . . . . . . . . . . . . . . . . . . . . .155
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . .80
over-temp condition . . . . . . . . . . . . . . . . .80
Terms, equipment marking . . . . . . . . . . . . . . . .5
Test pattern
generator . . . . . . . . . . . . . . . . . . . . . . . . .16
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
raster box . . . . . . . . . . . . . . . . . . . . . .49, 52
type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Timing
1-1 sampling . . . . . . . . . . . . . . . . . . . . . . .58
adjust menu . . . . . . . . . . . . . . . . . . . . . . .57
oversample . . . . . . . . . . . . . . . . . . . . . . . .58
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Trans time . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Transition time . . . . . . . . . . . . . . . . . . . . . . . . .47
Transitioning
automatically . . . . . . . . . . . . . . . . . . . . . .72
to a saved logo . . . . . . . . . . . . . . . . . . . . .90
Tree, menu . . . . . . . . . . . . . . . . . . . . . . . . . . .38
TRNTIME (command) . . . . . . . . . . . . . . . . . .155
Troubleshoot Ethernet connection . . . . . . . . . 113
Type
input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
test pattern . . . . . . . . . . . . . . . . . . . . . . . .48
r
Understanding auto acquire . . . . . . . . . . . . . .86
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Up/Down arrows . . . . . . . . . . . . . . . . . . . . . .106
Upgrade
software . . . . . . . . . . . . . . . . . . . . . . . . .107
software via Ethernet . . . . . . . . . . . . . . . 110
Upload
dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
status page . . . . . . . . . . . . . . . . . . . . . . . 112
User preference
auto input save . . . . . . . . . . . . . . . . . . . . .72
auto take . . . . . . . . . . . . . . . . . . . . . . . . . .72
menu . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
menu context . . . . . . . . . . . . . . . . . . . . . .72
Using
auto acquire . . . . . . . . . . . . . . . . . . . . . . .70
black . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
169
Index
BLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
ESC button . . . . . . . . . . . . . . . . . . . . .39, 40
freeze . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
HDCP . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
LOGO . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
SEL button . . . . . . . . . . . . . . . . . . . . .39, 40
setup menu . . . . . . . . . . . . . . . . . . . . . . . .46
s
V
active . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
position . . . . . . . . . . . . . . . . . . . . . . . . . . .59
size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
total . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Vacuum Fluorescent Display . . . . . . . . . . . . . .21
VER (command) . . . . . . . . . . . . . . . . . . . . . .155
Version, software . . . . . . . . . . . . . . . . . . . . . . .82
Vertical active area . . . . . . . . . . . . . . . . . . . . .59
VFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
brightness . . . . . . . . . . . . . . . . . . . . . . . . .73
VFDBRT (command) . . . . . . . . . . . . . . . . . . .155
t
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . .159
Web site . . . . . . . . . . . . . . . . . . . . . . . . . . . . .109
170
DCS-200 • User’s Guide
Download PDF

advertising