Belkin | Delphi Roady | User guide | Belkin Delphi Roady User guide

QuickGuide delphi option
7/13/05
8:54 AM
Page 1
Mounting roadyXT in your vehicle
Using roadyXT at home*
We’ve included two types of mounts to help you install your roadyXT in
your vehicle’s interior.
Turn off your roadyXT and your home
stereo. Connect your roadyXT to your
stereo as illustrated.
Activating your roadyXT
34
Swivel Mount
Find a suitable location; the mount uses a strong adhesive and you’ll have
difficulty repositioning it after installation. Do not install this mount on a
leather surface. Make sure the air temperature is at least 60°F.
Press the arrow
buttons to find
channel 0. Push
the “select” button
to choose it.
Place the antenna on a
window or an exterior wall
so that it points south.
You’ll see an 8character XM Radio
ID in the display.
(The XM Radio ID
does not use the
letters I, O, S, and F.)
Clean the mounting surface with the surface preparation
cleaning kit, following the directions on the package.
Peel away the adhesive liner and firmly press
the swivel mount to the surface for 30 seconds.
For best results, do not touch or apply any
pressure to the vehicle mount for 24 hours.
Activate your XM Satellite Radio service by contacting XM at
http://activate.xmradio.com or by calling 1.800.XM.RADIO (1.800.967.2346).
You will need the XM Radio ID and a major credit card.
To remove the mount, lift the adhesive pad
with your fingers or a spoon. You may warm it with a hair dryer for 2 to 3
minutes to help soften the adhesive. Remove any leftover adhesive from
the dash surface by rubbing with your finger, or use a mild cleaner as
recommended by your vehicle’s manufacturer.
XM will send a signal from the satellites to activate the full channel lineup.
Activation normally takes 10 to 15 minutes, but may take up to an hour
during peak busy periods.
When you can access the full channel lineup on your roadyXT, you’re done!
Caution: Never use a commercial heat gun or paint-stripping gun. This could result in damage to the unit
or to your vehicle.
You can adjust the tension of the swivel mount
by using a screwdriver.
*With roadyXT Home Kit, (model SA10176, sold separately)
Base of mount can be rotated to accommodate
vertical or horizontal surfaces. Choose the best
for your installation.
Slowly turn and tilt the antenna. The signal bars on the display will change.
Find the position that gives at least two bars on either “satellite” or
“terrestrial.”
• Save favorite channels as presets, which you can instantly recall by
pushing just one button.
• Save and recall the artist names and titles of your favorite songs.
• Use TuneSelect™ to find your favorite songs when they play on any
XM channel.
• Create a personal stock ticker.
• View sports scores, news, and more.
Check out your roadyXT User Guide for more information.
Delphi Corporation
1441 West Long Lake Road
Troy, Michigan 48098-5090
U.S.A.
Customer Service: [1] 877.GO DELPHI
The antenna aiming screen remains as long as it’s needed to help you position the antenna. When you’ve found the best position, press the “menu”
button twice to return to normal operation.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death.
Warning: The FCC and FAA have not certified the Delphi XM roadyXT Satellite Radio
Receiver for use in any aircraft (neither portable nor permanent installation). Therefore,
Delphi cannot support this type of application or installation.
The Delphi XM® roadyXT Satellite Radio Receiver incorporates an FM transmitter and is
therefore classified as an intentional transmitter. Changes or modifications to the unit not
expressly approved by Delphi can void your authority to operate this equipment.
FCC ID: RS2SA10177
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
Warning: roadyXT should be placed in your vehicle where it will not interfere with the function of safety features
(e.g., deployment of airbags). Failure to correctly place roadyXT may result in death and/or injury to yourself or to
others if the unit becomes detached during an accident and/or obstructs the deployment of an airbag.
Press the “menu” button. Use the arrow and “select” buttons to choose
“Antenna Aiming.” This feature is most helpful when using the roadyXT in
a stationary home or office environment.
Do more
www.delphi.com
Attach the power, antenna,
and audio cable (if needed).
Tuck the cables under the
plastic tab.
To help aim the antenna, use roadyXT’s “Antenna Aiming” feature.
roadyXT, the XM name, TuneSelect, and related
logos are trademarks of XM Satellite Radio Inc.
Insert your roadyXT receiver
into the vehicle cradle.
Turn on your roadyXT.
Printed on Recycled Paper
©2005 Delphi Corporation. All rights reserved.
DPSS-05-E-051
Vent Mount
Find a horizontal air vent that is strong
enough to hold your roadyXT and its
cradle. Clip the vent mount into the vent.
To remove the mount, push it into the
vent and lift upwards slightly to release
the mount’s hooks from the vent vanes.
Carefully extract the mount.
QuickGuide delphi option
7/13/05
8:54 AM
What’s in the box?
Page 2
Using roadyXT in your vehicle
Controls
Because every vehicle is different, we can only provide some general
guidelines. If you need help, consult a professional installer.
1 2
power
vehicle swivel
mount
roadyXT
receiver
vehicle power
adaptor
vehicle antenna
surface preparation kit
home antenna
roadyXT
Home Kit
sold separately
home cradle
(SA10176)
vehicle cradle
home power
adaptor
cassette adaptor
menu – access
advanced features
and configuration
options
up and down arrows,
select – change channels, choose menu
options, TuneSelect™
disp – change
what you see on
the display
remote
vehicle vent
mount
pre/dir – select
between direct
channel entry or
up to 30 presets
search – look up channels
by category or scan all
channels
memory – save
and recall up to
20 artist names
or song titles
jump – return to
previous channel;
press and hold to
select one of last
six FM frequencies
used for transmitter
• Always do a trial run before installing anything permanently. Temporarily
connect all power, audio, and antenna lines. Make sure that you receive
the XM signal and that you hear XM programming through your vehicle’s
audio system.
Audio quality
For a neat, fully integrated installation, use the DELPHI FM DIRECT
ADAPTOR (model SA10112, sold
separately). The FM Direct
Adaptor must be connected to
your car radio and to the car’s FM
antenna. We recommend that you
consult a professional installer.
numbers – enter a
channel directly or
select favorite presets
The WIRELESS FM TRANSMITTER is the easiest and quickest
way to hear XM programming
in your vehicle. Simply set your
FM radio and your roadyXT to
the same frequency.
audio cables
Additional Vehicle Kits sold separately (SA10178)
Display
signal strength –
1 to 3 bars
Remote Control*
search by scanning
all channels
display
modes 1-5
search channels
by category
Use the CASSETTE ADAPTOR
if your vehicle’s audio system
has a built-in cassette player.
• Decide which method (cassette adaptor, wired connection, or wireless
FM transmitter) is best for your vehicle and location.
channel selection
mode – direct
entry or preset
banks A, B, or C
Remember to pull out the clear plastic
tab from the remote battery compartment before using the remote.
To remove the battery from the remote,
use your thumb to press the center of
the battery tray and pull it out. Replace
the battery with the equivalent size and
voltage, taking care to insert it with the
positive (+) side up.
Placing the antenna
For best reception, place the XM antenna on the vehicle’s metallic roof, at least
6" from any window or sunroof. It can be placed in the front, middle, or rear
of the roof.
If the car is a hard- or soft-top convertible, you may mount the antenna on
the metal trunk lid. It should be at least 4" from the rear window. Ensure that
the antenna and cable don’t interfere with the opening or closing of the
convertible top and the trunk lid.
TIP: If you route the antenna cable through the
trunk seal, use the lowest part of the weather
seal. This should minimize any water leaks.
n1
tio
op
n2
power
menu – access
advanced features and
configuration options
up and down arrows, select –
change channels, choose
menu options, TuneSelect
additional info – channel
name, channel number,
artist, song title, Stock
Ticker, and Info Extras
search – look up
channels by category
or scan all channels
pre/dir – select between
direct channel entry or
up to 30 presets
tio
op
+ and – change channels,
or control volume if
roadyXT is placed in a
Delphi audio system
jump – return to previous
channel; press and hold
to select one of last six
FM frequencies used for
modulator
TIP: Don’t install the XM antenna inside your
vehicle or on a non-metallic surface. Doing so
will likely degrade the signal and you will probably
experience more signal interruptions.
numbers – enter a
channel directly or
select favorite presets
disp – change what you
see on the display; show
artist name, song title,
channel number, stock
quotes, or Info Extras
*Sold separately
TIP: If you use your roadyXT’s wireless
FM transmitter, mount the XM antenna
as close to your vehicle’s FM antenna
as possible. The FM antenna may be a
wire or metallic strip embedded in the
windshield or rear window.
memory – save and
recall up to 20 artist
names or song titles
Warning: Failure to properly install the antenna may result in injury to yourself or to
others if it becomes detached during an accident.
Download PDF

advertising