r® ELECTRONIC ELECTRIC DRYERS _Tc,_8_C'_ ____I"¸_¸_ _,:' For questions about features, operation/performance, parts, accessories or service, call: 1-800-688-9900 or visit our website at... www.amana.com Table of Contents ................................................. W10216186A 2 TABLEOF CONTENTS DRYER SAFETY .............................................................................. INSTALLATION INSTRUCTIONS .................................................. Tools and Parts ............................................................................ Optional Pedestal ......................................................................... Location Requirements ............................................................... Electrical Requirements ............................................................... Electrical Connection ................................................................... Venting Requirements ............................................................... Plan Vent System ...................................................................... Install Vent System .................................................................... Install Leveling Legs .................................................................. Connect Vent ............................................................................. Level Dryer ................................................................................ Reverse Door Swing ................................................................. Complete Installation ................................................................ DRYER USE ................................................................................. Starting Your Dryer .................................................................... Stopping Your Dryer ................................................................. Pausing or Restarting ................................................................ Control Locked .......................................................................... Drying and Cycle Tips ............................................................... 2 4 4 4 4 6 8 13 14 15 15 16 16 16 17 18 18 19 19 19 19 Status Lights .............................................................................. Cycles ........................................................................................ Options ...................................................................................... Modifiers .................................................................................... Changing Cycles, Options, and Modifiers ................................ End of Cycle Signal ................................................................... Drying Rack Options ................................................................. DRYER CARE .............................................................................. Cleaning the Dryer Location ...................................................... Cleaning the Lint Screen ........................................................... Cleaning the Dryer Interior ........................................................ Removing Accumulated Lint ..................................................... Vacation and Moving Care ........................................................ Changing the Drum Light .......................................................... TROUBLESHOOTING ................................................................. Dryer Operation ......................................................................... Dryer Results ............................................................................. ASSISTANCE OR SERVICE ........................................................ 20 20 21 22 22 22 22 23 23 23 24 24 24 24 25 25 25 27 WARRANTY ................................................................................. 28 DRYERSAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean: You can be killed or seriously follow instructions. injured if you don't immediately You can be killed or seriously instructions. injured if you don't follow All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. 2 WARNING - Clothes dryer installation - "Ris. ofFire" must be performed - install the clothes dryer according by a qualified to the manufacturer's installer. instructions and local codes. - Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire. - To reduce the risk of severe injury or death, follow all installation instructions. - Save these instructions. IM PORTANT SAFETY INSTRUCTIONS WARNING: Toreduce theriskoffire,electric shock,orinjury topersons whenusing the dryer, followbasicprecautions, including the following:  Read all instructions before using the dryer.  Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.  Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.  Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.  Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.  Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.  Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials. Clean lint screen before or after each load.   Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt. Do not reach into the dryer if the drum is moving.   Do not install or store the dryer where it will be exposed to the weather. The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.  See installation instructions  Do not tamper with controls.  Before the dryer is removed from service or discarded, remove the door to the drying compartment.  SAVE THESE INSTRUCTIONS for grounding requirements. INSTALLATIONINSTRUCTIONS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Flat-blade screwdriver • Vent clamps #2 Phillips screwdriver • Caulking gun and compound (for installing new exhaust vent) Adjustable wrench that opens to 1" (25.4 mm) or hex-head socket wrench (for adjusting dryer feet) • Tin snips (new vent installations) Wire stripper (for direct wire installations) • 1A" nut driver or socket wrench (recommended) Level • Tape measure Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of different heights separately for this dryer. You may select a 10" (254 ram) pedestal or a 15.5" (394 ram) pedestal with a storage drawer. The pedestal will add to the total height of the dryer for a total height of approximately 46" (1168 ram) or 51.5" (1308 ram), respectively. For a garage installation, you will need to place the 10" (254 ram) pedestal at least 9" (229 ram) above the floor. You will need to place the 15.5" (394 ram) pedestal at least 3" (76 ram) above the floor. Parts supplied Remove parts package from dryer drum. Check that all parts are included. Optional pedestal (15.5" [394 ram] model shown) To order, call the dealer from whom you purchased your dryer or refer to the "Assistance or Service" section. 4 Leveling legs NOTE: Do not use leveling legs if installing the dryer on a pedestal. Parts needed Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts. • Pedestal Height Color Part Number 10" (254 ram) White WHPIOOOSQ 15.5" (394 ram) White XHP1550VW 15.5" (394 ram) Burgundy XHP1550VM For close-clearance installations between 31.5" (800.1 mm) and 37" (939.8 mm), see "Plan Vent System" section for venting requirements. I<-- Explosion Hazard 37" "--_1 (939.8 ram) Keep flammable materials and vapors, such as gasoline, away from dryer. Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the "Assistance or Service" section. Place dryer at least 18 inches (460 ram) above the floor for a garage installation, Failure to do so can result in death, explosion, or fire. If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: You will need • • A location that allows for proper exhaust installation. See "Venting Requirements." • A separate 30-amp circuit. • If you are using a power supply cord, a grounded electrical outlet located within 2 ft (610 mm) of either side of the dryer. See "Electrical Requirements." • A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight of a companion appliance should also be considered. • 4 A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. A UL listed strain relief. • A level floor with a maximum slope of 1" (25 mm) under entire dryer. (If slope is greater than 1" [25 mm], install Extended Dryer Feet Kit, Part Number 279810.) Clothes may not tumble properly and automatic sensor cycles may not operate correctly if dryer is not level. • For a garage installation, you will need to place the dryer at least 18" (460 mm) above the floor. If you are using a pedestal, you will need 18" (460 mm) to the bottom of the dryer. Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended. Custom undercounter installation - Dryer only 1"* _ 25 mm _==--=27" --_ 686 ram) _--- 1"* (25mm) *Required spacing Closet installation - Dryer only The dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector. (76ram) 48in.2. (3100 mm2) _18" rnin.* Installation clearances The location must be large enough to allow the dryer door to open fully. f(457.2ram) Dryer Dimensions 24in.2. = (1550 mm2) (76ram) + I1"*1_-31,/2" _J6"**l (25ram) (800ram) (127ram) A 38 == A. Side view - closet or confined area B. Closet door with vents (965.2 *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. Recessed or closet installation - Dryer on pedestal IH 27 == (686 rnm) N *Most installations require a minimum 5" (127 mm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements." Installation spacing for recessed area or closet installation The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 mm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons: • Additional spacing should be considered for ease of installation and servicing. • Additional clearances might be required for wall, door, and floor moldings. • Additional spacing should be considered on all sides of the dryer to reduce noise transfer. • For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. • Companion appliance spacing should also be considered. 14m , 457.2 m__ 1" --_ (25mm) 1_-==27"_11_(===1 '' (686ram) (25 rnm) A I1"*_ 31,/2" +15.... (25 mm) (800ram) (127ram) B A. Recessed area B. Side view - closet or confined area *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. Installation • spacing for cabinet installation For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required. 7"* (178 mm) Mobile home - additional installation requirements This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). 7"* (178mm) Mobile home installations un require: • Metal exhaust system hardware, purchase from your dealer. • Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening. 9"* (229 mm) which is available for It is your responsibility • To contact a qualified electrical installer. • 5"** 311/2" 1"* 1" 27" 1" (127 mm) (800 mm) (25mm) (25mm)(686 mm)(25 mm) To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. The National Electric Code requires a 4-wire supply connection for homes built after 1996, dryer circuits involved in remodeling after 1996, and all mobile home installations. *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269. Recommended installation spacing for recessed or closet installation, with stacked washer and dryer To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit. The dimensions shown are for the recommended spacing. 48 in. 2 * (31000 mm 2) 3"* (76 mm) _,i//}ii iiii __ii'_ Do not use an extension cord. o If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. x¸ _ Electrical 3"* (76 mm) 24 in. 2 * + 1"* (25 mm) (15500mm2) • *Required spacing (1930 ram) 1" _ (25 mm) If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" in the "Electrical Connection" section. This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the external ground conductor screw (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor. 6"*_mm) 5½"**--}1_(140 mm) Connection To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. _ 27" -_-I (686 mm) (25 mm) *Required spacing **For side or bottom venting, 0" (0 mm) spacing is allowed. A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors. If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: • A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. • A UL listed strain relief. If your outlet looks like this: 4-wire receptacle (14-30R) Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover. If your outlet looks like this: GROUNDING  For a grounded, cord=connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.  For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. WARNING: Improper connection of the equipment= grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. SAVE THESE 3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R. If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire) and be: • Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated. • 10-gauge solid copper wire (do not use aluminum). • At least 5 ft (1.52 m) long. INSTRUCTIONS iNSTRUCTiONS Direct Wire Power Supply Cord Fire Hazard Fire Hazard Use a new UL listed 30 amp power supply cord. Use 10 gauge solid copper Use a UL listed strain relief. Use a UL listed strain relief. Disconnect power before making electrical connections. Ground wire (green or bare wire) must be connected green ground connector. Connect remaining 2 terminals (gold}. Securely Disconnect power. Remove the hold-down Ground wire (green or bare wire) must be connected green ground connector. Securely connections. 2 supply wires to remaining tighten all electrical connections. Style 1: Power supply cord strain relief screw and terminal block cover. D Remove the screws from a _/J' (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws enough to hold the two clamp sections together. ............................................................................................. A g / / A A. Neutral ground wire B. External ground conductor screw C. Center, silver-colored terminal block screw D. Terminal block cover and hold-down screw 3. Install strain relief. to Failure to do so can result in death, fire, or electrical shock. Failure to do so can result in death, fire, or electrical shock. 1. 2. to neutral wire (white or center wire) to center (silver). Connect remaining 2 terminals (gold). 2 supply wires to remaining tighten all electrical Disconnect power before making electrical connections. Connect terminal Connect neutral wire (white or center wire) to center terminal (silver}. wire. A. Strain relief tab pointing up B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. Electrical Connection Options If your home has: And you will be connecting to: Go to Section 4-wire receptacle (NEMA Type 14-30R) A UL listed, 120/240-volt 4-wire connection: Power supply cord 30-amp, dryer minimum, power supply cord* 4-wire direct A fused disconnect or 4-wire connection: Direct Wire circuit breaker box* (127 ram) Style 2: Direct wire strain relief Unscrew the removable conduit connector and any screws from a _/J' (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads. 3-wire receptacle (NEMA type 10-30R) 3-wire connection: Power supply cord A UL listed, 120/240-volt 30-amp, dryer power supply minimum, cord* _ 3-wire direct A fused disconnect or 3-wire connection: Direct Wire box* circuit breaker A *If local codes do not permit the connection of a cabinet-ground conductor to the neutral wire, go to "Optional 3-wire connection" section. B 4-wire C connection: Power supply cord IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. A .... ........... i "' _i' A. Removable conduit connector B. Hole below terminal block opening C. Strain relief threads C Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable. Now complete installation following instructions of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) for your type E A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. Ground prong D. Neutral prong E. Spade terminals with upturned ends F. 3/4"(19 mm) UL fisted strain relief G. Ring terminals 1. 4, D Remove center silver-colored terminal block screw. G 2, Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw. 4-wire connection: Direct wire IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 11/2"(38 mm) from 3 remaining wires. Strip insulation back 1" (25 mm). Shape ends of wires into a hook shape. (127 A. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw. B. Center silver-colored terminal block screw When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. C. Neutral ground wire D. Neutral wire (white or center wire) E. 3/4"(19 mm) UL listed strain relief 3, Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw. 1, 2. Remove center silver-colored terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw. C A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. :_" (19 mm) UL listed strain relief D. Center silver-colored terminal block screw D E E. Neutral ground wire F. Neutral wire (white or center wire) 4, Connect the other wires to outer terminal block screws. Tighten screws. ! A. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw. B. Center silver-colored terminal block screw C. Neutral ground wire D. Neutral wire (white or center wire) E. 3/4"(19 mm) UL listed strain relief 5. Tighten strain relief screws. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. "Venting Requirements." 10 Now go to 3, Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. C G F A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with upturned ends E. 3/4"(19 mm) UL listed strain relief E Ring terminals G. Neutral (white or center wire) 1, A. External ground conductor screw B. Ground wire (green or bare) of power supply cable C. 3/4"(19 mm) UL listed strain relief D. Center silver-colored terminal block screw 2. Loosen or remove center silver-colored terminal block screw. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. E. Neutral ground wire E Neutral wire (white or center wire) 4, C Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. A D E 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. "Venting Requirements." A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw Now go to D. Neutral wire (white or center wire) E. 3/4"(19 mm) UL listed strain relief 3, Connect the other wires to outer terminal block screws. Tighten screws. ! 4. Tighten strain relief screws. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. "Venting Requirements." Now go to 11 3-wire connection: Direct wire Use where local codes permit connecting cabinet-ground conductor to neutral wire. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 31/2'' (89 mm) of outer covering from end of cable. Strip insulation back 1" (25 mm). If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape. 4. Tighten strain relief screw. 5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. "Venting Requirements." Now go to Optional 3-wire connection When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. 1, 2. Loosen or remove center silver-colored Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire. 1. Remove center silver-colored 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw. terminal block screw. D terminal block screw. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw. F B A. External ground conductor screw B. Center silver-colored terminal block screw C. D. E. E 3, A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw 12 Connect the other wires to outer terminal block screws. Tighten screws. ! D. Neutral wire (white or center wire) E. 3/4"(19 mm) UL fisted strain relief 3, Neutral ground wire Neutral wire (white or center wire) 3/4"(19 mm) UL listed strain relief Grounding path determined by a quafified electrician Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. 4, Tighten strain relief screws. 5. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground. 6, Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. • Flexible metal vent must be fully extended and supported when the dryer is in its final location. • Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance. • Do not install flexible metal vent in enclosed walls, ceilings, or floors. • The total length of flexible metal vent should not exceed 73Aft (2.4 m). Elbows Fire Hazard 45 ° elbows provide better airflow than 90 ° elbows. Use a heavy metal vent, Do not use a plastic vent, Do not use a metal foil vent. Failure to follow these instructions can result in death or fire. WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. Good Clamps Use clamps to seal all joints. The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. If using an existing Better Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct and catch lint. Do not use duct tape. vent system • Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. • Replace any plastic or metal foil vent with rigid or flexible heavy metal vent. • Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance. Clamp Exhaust Recommended hood styles are shown here. If this is a new vent system Vent material • Use a heavy metal vent. Do not use plastic or metal foil vent. • 4" (102 mm) heavy metal exhaust vent and clamps must be used. DURASAFE TM venting products are recommended. _4, ( 1J24_n_m ) (102 ram} A. Louvered hood style B. Box hood style The angled hood style (shown here) is acceptable. 4" (102 mm) heavy metal exhaust vent 4" DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section. (102 mm)_(_ V'_ Rigid metal vent • For best drying performance, recommended. • Rigid metal vent is recommended kinking. rigid metal vents are to avoid crushing and Flexible metal vent • 21/2" (63.5 ram} Flexible metal vents are acceptable cleaning. • An exhaust hood should cap the vent to keep rodents and insects from entering the home. • Exhaust hood must be at least 12" (305 mm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.). only if accessible for 13 • Do not use an exhaust hood with a magnetic latch. Improper venting can cause moisture and lint to collect indoors, which may result in:  Moisture damage to woodwork, carpets, etc.  Housecleaning furniture, paint, wallpaper, problems and health problems. Choose your exhaust Recommended Optional exhaust installations This dryer can be converted to exhaust out the right side, left side, or through the bottom. Contact your local dealer to have the dryer converted. Fire Hazard installation type Cover unused exhaust holes with one of the following kits: exhaust installations Typical installations vent the dryer from the rear of the dryer. Other installations are possible. B 279818 (white} W10186596 (midnight Contact grey} your local dealer. Failure to follow these instructions can result in death, fire, electrical shock, or serious injury. A .......................... i, ................................................. H A. B. C. D. Dryer Elbow Waft Exhaust hood E. Clamps F. Rigid metal or flexible metal vent G. Ventlength necessary to connect elbows H. Exhaust outlet A B C A. Standard rear offset exhaust installation B. Left or right side exhaust installation C. Bottom exhaust installation (not an option with pedestal installations) Alternate installations for close clearances Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer's instructions. i!il A B A. Over-the-top installation (also available with one offset elbow) B. Periscope installation NOTE: The following kits for close clearance alternate installations are available for purchase. To order, please see the "Assistance or Service" section. • 14 Over-the-Top Installation: Part Number 4396028 Periscope Installation (For use with dryer vent to wall vent mismatch): Part Number 4396037 - 0" (0 mm) to 18" (457.2 mm) mismatch Part Number 4396011 - 18" (457.2 mm) to 29" (736.6 mm) mismatch Number of 90 ° turns or elbows Type of vent Box or Louvered hoods Angled hoods 3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m) 4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m) Part Number 4396014 - 29" (736.6 mm) to 50" (1270 mm) mismatch Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside. /_C_tl 1. 2. 3. _ s_ .... C_c,_s_ . Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (102 mm) clamp. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape, screws, or other fastening devices that extend into the interior of the vent to secure vent. Items sticking through the vent can catch lint. Excessive Weight Hazard Determine vent path Use two or more people to move and install dryer. • Select the route that will provide the straightest direct path outdoors. • Plan the installation to use the fewest number of elbows and turns. 1. • When using elbows or making turns, allow as much room as possible. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer. 2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration. 3. Examine the leveling legs. Find the diamond marking. • Bend vent gradually to avoid kinking. • Use the fewest 90 ° turns possible. Determine vent length drying performance and elbows needed and most Failure to do so can result in back or other injury. for best • Use the following Vent system chart to determine type of vent material and hood combinations acceptable to use. • NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will: • Shorten the life of the dryer. • Reduce performance, resulting in longer drying times and increased energy usage. "1 The Vent system chart provides venting requirements that will help to achieve the best drying performance. Vent system chart NOTE: Side and bottom exhaust installations have a 90 ° turn inside the dryer. To determine maximum exhaust length, add one 90 ° turn to the chart. Number of 90 ° turns or elbows Type of vent Box or Louvered hoods Angled hoods 0 Rigid metal 64 ft (20 m) 58 ft (17.7 m) 1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m) 2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m) 4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible. 5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent. 15 Lay the dryer door on a flat, protected surface with the inside door assembly facing up. 4= 1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (102 mm) clamp. 2. Move dryer into its final location. Do not crush or kink vent. 3. (On gas models) Check that there are no kinks in the flexible gas line. Once the exhaust vent connection is made, remove the corner posts and cardboard. 4. Check the levelness of the dryer. Check levelness first side to side, then front to back. Remove the 5 screws to release the outer door assembly from the inner door assembly, as indicated below. It is important that you remove only the 5 indicated screws. iQ__ Lift the inner door assembly off of the outer door assembly. Set the outer door assembly aside. 5= Reverse the hinge 1. Place the inner door, screw head side up, on the work space. 2. Remove the 4 hinge screws that hold the hinge to the door and remove hinge. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. C Swng You can change your door swing from a right-side left-side opening, if desired. opening to a C NOTE: For ease of installation, you may want to use 2 or more people to remove and reattach the dryer door. Remove the door 1. Place a towel or soft cloth on top of the dryer or work space to protect the surface. 2. Open the dryer door. Remove the 5 screws that hold the door hinge on the front panel of the dryer. A. Hinge side screw B. Locator pins on hinge C. Top side screw Move the large hole screw to the opposite side. Remove the 2 plug screws and plastic plugs, and insert them in the original screw holes on the opposite side. 3= A_ A. Dryer front panel B. Dryer door C. Screws 3. Remove the door. A. Hinge screws B. Large hole screw C. Plug screws and plastic plugs 16 4. Move hinge to the other side and reattach with the 4 screws removed in Step 2. Make sure Iocator pins line up in holes and drive the top 2 screws in place first to help drive Iocator pins into proper location. 5. Set the inner door assembly aside. 4. Align the door by placing the locating tabs on the hinge with the locating holes on the dryer front panel. Insert and tighten the center hinge screw. The door will hang in place while you insert and tighten the remaining 4 screws. NOTE: Two or more people may be needed to reattach the dryer door. Reverse the door handle 1. Place the outer door assembly face down on work space. 2. Remove the 6 screws that hold the intermediate door to the outer door assembly. Remove the intermediate door, and set hinge shield aside. Remove the hinge hole cover. / C A. Dryer door B. Dryer front panel C. Insert this hinge screw first. A. Intermediate 5. Close the door and check that it latches securely. 6. Check for fingerprints necessary. 1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer's final location. Be sure the vent is not crushed or kinked. 5. Check that the dryer is level. See "Level Dryer." 6. For power supply cord installation, plug into an outlet. For direct wire installation, reconnect power. 7. Remove the blue protective film on the console and any tape remaining on the dryer. 8. Read "Dryer Use." 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. door on the glass. Clean the glass if B. Hinge shield C. Hinge hole cover 3. Rotate the window assembly 180° and reattach the intermediate door, hinge shield, and hinge hole cover with the 6 screws removed in Step 2. Reinstalling the door 1. Place the inner door assembly into the outer door assembly. To fit correctly, the inside door assembly edge is completely inside the outside door assembly edge. 2. Reassemble the inner and outer door assemblies with the 5 screws. 10. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Dry Temperature setting. If the dryer will not start, check 3. Remove existing label from the opposite side of the door and discard. Find label provided with the Use and Care Guide and apply over original hinge holes. the following: • Controls are set in a running or "On" position. • The Start button has been pushed firmly. • Dryer is plugged into an outlet and/or electrical supply is connected. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. This dryer automatically runs an installation diagnostic routine at the start of its first cycle. If you receive an L2 code, there may be a problem with your home power supply keeping the dryer's heater from turning on. See "Troubleshooting." If you receive an AF code, your dryer vent may be crushed or blocked. See "Troubleshooting." NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away. 17 DRYERUSE Drum Lghl_ 0 .,_ "% ....... [email protected] Fire Hazard Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Do not dry anything that has ever had anything flammable on it (even after washing}. Failure to follow these instructions can result in death, explosion, or fire. No washer can completely Items containing foam, rubber, or plastic must be dried on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death or fire. Select DRYNESS LEVEL to adjust how dry you want the load. As the cycle runs, the control senses the dryness of the load and adjusts the time automatically for the selected dryness level. WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. Follow these basic steps to start your dryer. Please refer to specific sections of this manual for more detailed information. 1. Clean lint screen before each load. See "Cleaning the Lint Screen." 2. Place laundry in dryer and shut door. 3. Press the POWER button. Then rotate the dial or press a Timed Cycles button to select the desired Automatic or Timed Cycle. The indicator light for the selected Automatic or Timed cycle will glow green. The preset modifiers for the selected cycle will glow green. Selectable options will glow amber. If an option or modifier is unavailable with the selected cycle, the light will not illuminate. The estimated or actual cycle time (in minutes) will show in the display. To use an Automatic Cycle NOTE: Most loads may be dried using Normal dryness level, which is shown in bold letters on your control panel. Normal is the energy preferred dryness level and will use the least energy. Select the desired Options. To make changes during an Automatic Cycle: • Press STOP once. • Adjust Dryness Level. NOTE: Dryness Level selections can be made only while using Automatic Cycles. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More Dry, Normal, or Less Dry. Selecting More Dry, Normal, or Less Dry automatically adjusts the sensed time needed. More NOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is selectable. The light will not glow when the selection is unavailable with the cycle or option combinations selected. • Select an Automatic Cycle. Dry Norman Less Dry © Dryness AUtO 18 remove oil. Do not dry anything that has ever had any type of oil on it (including cooking oils}. CYCLES Level ONLY Now Automatic Cycles Work The AccelerCare function improves drying performance with Auto Moisture Sensing Plus, which advances the cycle as moisture is extracted from clothing. A thermistor (electronic temperature sensor) and moisture sensing strips in the dryer drum help measure the amount of moisture in the clothes as they tumble. An electronic control determines the load type to help save time, avoid overdrying, and increase the accuracy of the end dryness level. After the first 5 minutes of an automatic cycle, the estimated time display will adjust based on the approximate load size, cycle, dryness level selected, and amount of moisture left in the clothes. When the clothes have reached approximately 80% of the dryness level selected, the estimated time display will adjust again, showing the final drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and enhances fabric care. To use a Timed Cycle NOTE: A light next to each feature will glow green when the feature is selected or will glow amber when the feature is selectable. The light will not glow when the selection is unavailable with the cycle or option combinations selected. • Press a Timed Cycles button or, to select Air Fluff, rotate the control knob to the desired cycle. • Press MORE TIME or LESS TIME until the desired drying time is displayed. Tap MORE TIME or LESS TIME, and the time will change by 1-minute intervals. Press and hold MORE TIME or LESS TIME, and the time will change by 5-minute intervals. NOTE: The More Time and Less Time buttons can be used only with Timed Cycles. 0% E T/4z Timed @O Press TEMPERATURE glows. until the desired g To restart the dryer Close the door. Press and hold START until dryer starts. NOTE: Drying will continue from where the cycle was interrupted if you close the door and press START within 5 minutes. If the cycle is interrupted for more than 5 minutes, the dryer will shut off. Select new cycle settings before restarting the dryer. This feature allows you to lock your settings to avoid unintended use of the dryer. You can also use the Control Locked feature to avoid unintended cycle or option changes during dryer operation. To enable the Control Locked feature: Press and hold CYCLE SIGNAL for 3 seconds. The Control Locked indicator light glows, and a single beep tone is heard. To unlock, press and hold CYCLE SIGNAL for 3 seconds. The indicator light turns off. Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle is running, the display shows the estimated cycle time, which is determined by your dryer automatically sensing the dryness level of your load. If a Timed Cycle is running, the display shows the exact number of minutes remaining in the cycle. Cool Down tumbles the load without heat during the last few minutes of all cycles. Cool Down makes the loads easier to handle and reduces wrinkling. The length of the Cool Down depends on the load size and dryness level. h" Cycle I -- • ............S .................. To pause the dryer at any time Open the door or press STOP once. temperature Drying tips • Follow care label directions when they are available. • NOTE: During a Timed Cycle, you can change the settings for Time, Temperature, Wrinkle Prevent, and End of Cycle Signal. Press STOP twice to stop the dryer and clear the settings. Select another cycle or option. If desired, add a fabric softener sheet. Follow package instructions. • To reduce wrinkling, remove the load from the dryer as soon as tumbling stops. This is especially important for permanent press, knits, and synthetic fabrics. 4, (OPTIONAL STEP) If desired, select OPTIONS. For more details, see "Options." • 5. (OPTIONAL STEP) If desired, set the End of Cycle Signal. Select LOUD or SOFT by pressing the Cycle Signal button to alert you when a cycle ends. Avoid drying heavy work clothes together with lighter fabrics. This could cause overdrying of lighter fabrics and lead to increased shrinkage or wrinkling. 6, Press and hold START for approximately dryer starts. Be sure the door is closed. 3 seconds until • If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off. • If you wish to end your drying cycle after pressing Start, press Stop twice. To stop your dryer at any time Press STOP twice or open the door. Cycle tips • Dry most loads using the preset cycle settings. • Refer to the Automatic or Timed Cycles Preset Settings chart (in the "Cycles" section) for a guide to drying various loads. Drying temperature and Dryness Level are preset when you choose an Automatic Cycle. You can select a different dryness level, depending on your load, by pressing Dryness Level and choosing More Dry, Normal or Less Dry. NOTE: You cannot use the Timed Cycle Adjust and you cannot modify temperature with the Automatic Cycles. If you wish to adjust the cycle length of a Timed Cycle, press More Time or Less Time. Adjust the temperature of a Timed Cycle by pressing TEMPERATURE until the desired temperature is selected. NOTE: You cannot use the Dryness Level with Timed Cycles. 19 You may follow the progress of your dryer with the drying Status indicator lights. Select the drying cycle that matches the type of load you are drying. See Automatic Dry chart or Timed Preset Cycle Settings chart. Power TIMED CYCLES 0 0 Norraa|. Casual oooim./// Timed Dry Timed Cycle The Timed Cycle light glows green during a Timed Cycle. © Quick Dry ECK L INT Wet The Wet light glows green at the beginning of Automatic Cycle if a wet item is detected or in a timed cycle after 5 minutes. • • In an Automatic Cycle, if a wet item is not detected after 5 minutes, the dryer will run for a preset minimum run time (based on the selected cycle and dryness level setting) and then go into Cool Down. The Cool Down and Wrinkle Prevent indicators will glow green, if selected. In a Timed Cycle, the Wet light will glow green after 5 minutes and remain on until the dryer enters Cool Down. Damp The Damp light glows green in an Automatic Cycle when the laundry is approximately 80% dry. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing. To be alerted when the load is about 80% dry, you may use the damp dry signal option. See Damp Dry Signal in "Options." Cool Down The Cool Down light glows green during the cool down part of the cycle. Laundry cools for ease in handling. Clothes Dry The Clothes Dry light glows green when the drying cycle is finished. This indicator stays on during Wrinkle Prevent. Wrinkle Prevent The Wrinkle Prevent light glows green when this option is selected. This indicator stays on with Clothes Dry. SCRFFN Touch Up Automatic Cycles Automatic Cycles allow you to match the cycle to the load you are drying. See the following Automatic Dry Preset Cycle Settings chart. Each cycle dries certain fabrics at the recommended temperature. A sensor detects the moisture in the load and automatically adjusts the drying time for optimal drying. Heavy Duty Use this cycle to get high heat for heavyweight cotton towels, or bedspreads. mixed loads, Denim Use this cycle to get medium high heat for drying denims. Normal Use this cycle to get medium heat for drying sturdy fabrics such as work clothes and sheets. Casual Use this cycle to get low heat for drying no-iron fabrics, such as sport shirts, casual business clothes, and permanent press blends. Delicate Use this cycle to get extra-low heat to gently dry items such as lingerie, blouses, or washable knit fabrics. Automatic Dry Preset Cycle Settings Sensing/Revising Est. Time The Sensing/Revising Est. Time light glows green when moisture sensing strips in the dryer drum are measuring the amount of moisture in the clothes. The estimated time display may adjust to show a more accurate drying time. Indicator lights Other indicator lights show Cycle, Options, Modifiers, End of Cycle and Control Lock settings selected. The display shows the estimated or actual time remaining. Automatic Cycles Load Type Temperature Time* (Minutes) HEAVY DUTY Heavyweight mixed loads, cotton towels, bedspreads High 45 DENIM Denim jeans, jackets Medium High 55 NORMAL Corduroys, work clothes, sheets Medium 40 CASUAL Permanent press, synthetics Low 35 DELICATE Lingerie, blouses, washable knit fabrics Extra Low 30 *Estimated Time with Dryness Level (Normal) setting. Time will vary depending on load type and load size. 20 Timed Cycles Use Timed Cycles to select a specific amount of drying time and a drying temperature. (Temperatures are not selectable with Air Fluff.) When a Timed Cycle is selected, the Estimated Time Remaining display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing More Time or Less Time. See "Changing Cycles, Options, and Modifiers." You can customize your cycles by selecting options. Not all Options are available with all cycles. Current selections will glow green. If an option is unavailable with a selected cycle, the light will not illuminate when pressed and an error sound will be heard. OPTIONS Prevent Wrinkle Timed Dry Use this cycle to complete drying if items are still damp after an Automatic Cycle. Timed Dry is also useful for drying heavyweight and bulky items, such as bedspreads and work clothes. Lightweight garments, such as exercise wear, can be dried using Timed Dry on a low temperature setting. Quick Dry Use this cycle for drying small loads or loads that need a short drying time. Touch Up Use this cycle to help smooth out wrinkles from items, such as clothes packed in a suitcase or items wrinkled from being left in the dryer too long. Air Fluff Rotate the dial to Air Fluff to use this cycle for items that require drying without heat such as rubber, plastic, and heat-sensitive fabrics. This table shows examples of items that can be dried using Air Fluff. The temperature setting is not adjustable with this cycle. Type of Load Time* (Minutes) Foam rubber - pillows, padded bras, stuffed toys 20 - 30 Plastic - Shower curtains, tablecloths 20 - 30 Rubber-backed 40 - 50 rugs Olefin, polypropylene, sheer nylon 10 - 20 0 Signal Damp 0 CvCES Dry ONlY AUTO Sounds Button O Drum Light 0 Wrinkle Prevent Wrinkle Prevent helps smooth out wrinkles that form when you cannot unload the dryer promptly at the end of a cycle. During this option, the dryer stops tumbling and then tumbles again for a brief period. • Press WRINKLE PREVENT to get up to 2 hours of heat-free, periodic tumbling at the end of a cycle. • Stop Wrinkle Prevent at any time by pressing WRINKLE PREVENT or opening the dryer door. • For the Casual cycle, Wrinkle Prevent is preset to ON. The other cycles will retain the Wrinkle Prevent setting. For example, if you select Wrinkle Prevent in the Normal cycle, Wrinkle Prevent will be on the next time you select the Normal cycle. NOTE: If you do not select Wrinkle Prevent, the dryer stops after cool down. Damp Dry Signal Select the Damp Dry Signal to alert you that your clothes are approximately 80% dry. This is useful when you want to remove lightweight items in a mixed load to avoid overdrying or remove partially dry items that may need ironing. NOTE: The Damp Dry Signal is available only with the Automatic Cycles. *Reset cycle to complete drying, if needed. When using Air Fluff Button Sounds • Check that coverings are securely stitched. • Shake and fluff pillows by hand periodically during the cycle. • Dry item completely. Foam rubber pillows are slow to dry. Timed Preset Cycle Settings Timed Cycles Load Type Default Temperature Default Time (Minutes) TIMED DRY Heavyweight, bulky items, bedspreads, work clothes High 40 QUICK DRY Small loads High 23 TOUCH UP Helps to smooth out wrinkles Medium High 20 AIR FLUFF Dry without heat Air Dry (no heat) 36 You can change the volume of the sound of the beeps. Press BUTTON SOUNDS until the desired volume (Loud, Soft, or Off) glows. The Power and Cancel buttons will still beep softly when the Button Sounds volume is set to Off. Drum Light Press DRUM LIGHT to turn on the light inside the dryer drum. During a cycle, if Drum Light is selected, the drum light turns on and will remain on until Drum Light is pressed again, the door is open and closed, or the door is left open for 5 minutes. When the dryer is not running, the Drum Light is pressed or the dryer remain on until the dryer door has dryer door is closed or Drum Light drum light will turn on when door is opened, and it will been open for 5 minutes, the is pressed again. Press DRUM LIGHT at any time to turn the drum light ON or OFE *Use the Air Fluff cycle for items that require drying without heat such as rubber, plastic, and heat-sensitive fabrics. 21 Use Modifiers to select time, temperatures, and dryness levels for the Timed Cycles. Not all Modifiers are available with all options and cycles. Available modifier settings will glow amber. Current selections will glow green. If a modifier is unavailable with a selected cycle, the light will not illuminate. Time Press MORE TIME or LESS TIME until the desired drying time is displayed. The time cannot be changed with Automatic Cycles. Adjustl Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions, or personal preference. There are 3 drying settings: 1 (factory preset dryness level), 2 (slightly dryer clothes, approximately 15% more drying time), and 3 (much dryer clothes, approximately 30% more drying time). 1. O_,E [email protected] Timed iO Cycle Changing the Preset Dryness Level Settings If all of your loads on all Automatic Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your Automatic Dry cycles. _" 2. O %s x\_4\e" Temperature Press TEMPERATURE until the desired temperature setting glows. Temperature modifiers cannot be used with the Automatic Cycles or the Air Fluff cycle. O TIMED CYCLES 3. To select a new drying setting, press the DRYNESS LEVEL button again until the desired drying setting is shown. NOTE: While you are cycling through the settings, the current setting will not flash, but the other settings will flash. 4. Press START to save the drying setting. The drying setting you selected will become your new preset drying setting for all Automatic Dry cycles. End of Cycle Signal The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling. Temperature ADJUSTS The Dryness Level settings cannot be changed while the dryer is running. Press and hold the DRYNESS LEVEL button for 5 seconds. The dryer will beep, and "CF" will be displayed for 1 second followed by the current drying setting. ONLY Loud Dryness Level Press DRYNESS LEVEL until the desired Dryness Level is selected. Dryness Level cannot be adjusted with Timed Cycles. Soft Off °O UNLOCK O Dryness AUTO Level CYCLES ONLY You can change Automatic Cycles, Timed Cycles, Modifiers, and Options anytime before pressing Start. • Three short tones sound if an unavailable combination is selected. The last selection will not be accepted. Changing Cycles after pressing Start 1. Press STOP twice. This ends the current cycle. 2. Select the desired cycle and options. 3. Press and hold START. The dryer starts at the beginning of the new cycle. NOTE: If you do not press START within 5 minutes of selecting the cycle, the dryer automatically shuts off. Changing Modifiers and Options after pressing Start You can change a Modifier or Option anytime before the selected Modifier or Option begins. 1. Press STOP once. 2. Select the new Modifier and/or Option. 3. Press and hold START to continue the cycle. NOTE: If you happen to press Stop twice, the program clears and your dryer shuts down. Restart the selection process. 22 CONTROLS Press CYCLE SIGNAL to adjust the sound level or turn off the signal. NOTE: When Wrinkle Prevent is selected and the End of Cycle Signal is on, a tone sounds every 5 minutes until the clothes are removed, or Wrinkle Prevent ends. The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for example, sweaters). If your model does not have a drying rack, you may be able to purchase one for your model. To find out whether your model allows drying rack usage and for information on ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer. The dryer rack is recommended for use with the Air Fluff cycle or with Timed Dry cycles. The dryer rack cannot be used with Automatic Cycles. To use the heated dryer rack: Do not remove the lint screen. 1. Close the door. 5. Rotate the dial to the Air Fluff cycle or press Timed Dry. Select a drying time by pressing MORE TIME or LESS TIME. Press TEMPERATURE until the desired temperature glows. Items containing foam, rubber, or plastic must be dried on a clothesline or by using the Air Fluff cycle. Refer to the following table. 6. When Air Fluff is selected, the Estimated Time Remaining display shows the default time. You can change the actual time in the cycle by pressing More Time or Less Time. 7. Start the dryer. Open dryer door. A NOTE: Check the lint screen and remove any lint accumulated from items dried on the rack after the cycle is finished. A. Front edge 2. 4. Place dryer rack over the bottom of the dryer door opening. Rest the back wire on the dryer back ledge. Push down on the frame front to secure over lint screen. Dryer Rack Cycle Temp. Time* Wool sweaters Timed Dry Low 60 Timed Dry Low 60 Stuffed toys or pillows Foam rubber filled Air Fluff Air Only (no heat) 90 Sneakers shoes Air Fluff Air Only (no heat) 90 Block to shape and lay flat on the rack Stuffed toys or pillows Cotton or polyester fiber filled A. Dryer rack front edge B. Dryer back panel 3. Place wet items on top of the rack. Allow space around items for air to circulate. The rack does not move, but the drum will rotate. Make sure items do not hang over the edges or between rack grille. or canvas *Reset cycle to complete drying if needed. NOTE: You must remove rack for normal tumbling. To remove the dryer rack, lift it straight up and out of the dryer. DRYERCARE Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air. Explosion Every load cleaning The lint screen is located in the door opening of the dryer. The control panel has an indicator light to remind you to clean the lint screen before each load. A screen blocked by lint can increase drying time. To clean 1. Pull the lint screen straight up. Roll lint off the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove. 2. Push the lint screen firmly back into place. Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Place dryer at least 18 inches (460 ram) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. 23 IMPORTANT: • Do not run the dryer with the lint screen loose, damaged, blocked, or missing. Doing so can cause overheating and damage to both the dryer and fabrics. • If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint. See "Venting Requirements." As needed cleaning Laundry detergent and fabric softener residue can build up on the lint screen. This buildup can cause longer drying times for your clothes, or cause the dryer to stop before your load is completely dry. The screen is probably clogged if lint falls off while the screen is in the dryer. Vacation care Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should: 1. Unplug dryer or disconnect 2. Clean lint screen. See "Cleaning the Lint Screen." Moving power. care Clean the lint screen with a nylon brush every 6 months, or more frequently, if it becomes clogged due to a residue buildup. To wash For power supply cord-connected 1. Unplug the power supply cord. 2. Make sure leveling legs are secure in dryer base. 1. 2. Roll lint off the screen with your fingers. Wet both sides of lint screen with hot water. 3. Use masking tape to secure dryer door. 3. Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to remove residue buildup. For direct-wired dryers: dryers: Electrical Shock Hazard Disconnect power before servicing. 4. Rinse screen with hot water. Replace all parts and panels before operating. 5. Thoroughly dry lint screen with a clean towel. Replace screen in dryer. Failure to do so can result in death or electrical To clean dryer drum 1. Make a paste with powdered laundry detergent and very warm water. 2. Apply paste to a soft cloth. OR Apply a liquid, nonflammable household cleaner to the stained area and rub with a soft cloth until all excess dye and stains are removed. 3. Wipe drum thoroughly with a damp cloth. 4. Tumble a load of clean cloths or towels to dry drum. 1. Disconnect power. 2. Disconnect wiring. 3. Make sure leveling legs are secure in dryer base. 4. Use masking tape to secure dryer door. The dryer light automatically you open the door. shock. turns on inside the dryer drum when To change the drum light 1. Unplug dryer or disconnect power. 2. Open the dryer door. Locate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right corner of the cover. Remove the cover. 3. Turn bulb counterclockwise. Replace the bulb with a 10-watt appliance bulb only. Replace the cover and secure with the screw. 4. Plug in dryer or reconnect power. NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside out to avoid transfer of dye. From Inside the Dryer Cabinet Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified person. From the Exhaust Vent Lint should be removed every 2 years, or more often, depending on dryer usage. 24 TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call... Try the following: Check to see if a household fuse has blown or circuit breaker has tripped. Electric dryers use two household fuses or breakers. Replace the fuse or reset the circuit breaker. Dryer will not run • Confirm the power cord is properly installed. Refer to "Electrical Connection" section for details. Has a fuse blown, or has a circuit breaker tripped? There may be 2 fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Select a Timed Dry heated cycle, and restart the dryer. If the message persists, consult a qualified electrician. • Is the correct power supply available? Electric dryers require 240-volt power supply. Check with a qualified electrician. "AF" (low airflow condition): The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display and return to the estimated time remaining. • Was a regular fuse used? Use a time-delay fuse. Try the following: Clean lint screen. • Is the dryer door firmly closed? Check to see if the vent run from the dryer to the wall is crushed or kinked. • Was the Start button firmly pressed? Large loads may require pressing and holding the Start button for 2-5 seconds. Confirm the vent run from the dryer to the wall is free of lint and debris. Confirm the exterior vent exhaust hood is free of lint and debris. No heat • Confirm your vent system falls within the recommended run length and number of elbows for the type of vent you are using. Refer to "Plan Vent System" for details. Has a fuse blown, or has a circuit breaker tripped? The drum may be turning, but you may not have heat. Electric dryers use 2 fuses or circuit breakers. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician. Select a Timed Dry heated cycle, and restart the dryer. If the message persists, have your entire home venting run cleaned. Unusual sounds "F" Variable (F1, F2, F20) service codes: Call for service. • Has the dryer had a period of non-use? If the dryer hasn't been used for a while, there may be a thumping sound during the first few minutes of operation. • Is a coin, button, or paper clip caught between the drum and front or rear of the dryer? Check the front and rear edges of the drum for small objects. Clean out pockets before laundering. • Are the four legs installed, and is the dryer level front to back and side to side? The dryer may vibrate if not properly installed. See the Installation Instructions. • Is the clothing knotted or balled up? When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer. Dryer displaying Clothes are not drying satisfactorily, long, or load is too hot • drying times are too Is the lint screen clogged with lint? Lint screen should be cleaned before each load. code message "PF" (power failure), check the following: Was the drying cycle interrupted by a power failure? Press and hold START to restart the dryer. "L2" Diagnostic Code (low or no line voltage condition): The drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display and return to the estimated time remaining. Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to follow or fire. these instructions can result in death 25 • • • • Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement? Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See "Venting Requirements." Cycle time too short Excessive Weight Hazard Are fabric softener sheets blocking the lint screen grille? Use only one fabric softener sheet, and use it only once. Use two or more people to move and install dryer. Failure to do so can result in back or other injury. Is the exhaust vent the correct length? Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See "Plan Vent System." Is the automatic cycle ending early? The load may not be contacting the sensor strips. Level the dryer. Is the exhaust vent diameter the correct size? Use 4" (102 mm) diameter vent material. Change the dryness level setting on Automatic Cycles. Increasing or decreasing the dryness level will change the amount of drying time in a cycle. Do not use a dryer rack with an automatic cycle. Lint on load • Explosion Hazard Stains on load or drum Keep flammable materials and vapors, such as gasoline, away from dryer. Was dryer fabric softener properly used? Add dryer fabric softener sheets at the beginning of the cycle. Fabric softener sheets added to a partially dried load can stain your garments. Place dryer at least 18 inches (460 ram) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire. Is the dryer located in a room with temperature below 45°F (7°C)? Proper operation of dryer cycles requires temperatures above 45°F (7°C). Is the dryer located in a closet? Closet doors must have ventilation openings at the top and bottom of the door. The front of the dryer requires a minimum of 1" (25 mm) of airspace, and, for most installations, the rear of the dryer requires 5" (127 mm). See "Installation Instructions." Has an air dry cycle been selected? Select the right cycle for the types of garments being dried. See "Modifiers." Is the load too large and heavy to dry quickly? Separate the load to tumble freely. 26 Is the lint screen clogged? Clean lint screen. Check for air movement. Drum stains are caused by dyes in clothing (usually blue jeans). This will not transfer to other clothing. Loads are wrinkled • Was the load removed from dryer at the end of the cycle? • Was the dryer overloaded? Dry smaller loads that can tumble freely. Odors • Have you recently been painting, staining, or varnishing in the area where your dryer is located? If so, ventilate the area. When the odors or fumes are gone from the area, rewash and dry the clothing. • Is the dryer being used for the first time? The new electric heating element may have an odor. The odor will be gone after the first cycle. ASSISTANCEOR SERVICE Before calling for assistance or service, please check "Troubleshooting." It may save you the cost of a service call. If you still need help, follow the instructions below. For Assistance When calling, please know the purchase date and the complete model and serial number of your appliance. This information will help us to better respond to your request. Our consultants If you need replacement parts If you need to order replacement parts, we recommend that you use only factory specified parts. Factory specified parts will fit right and work right because they are made with the same precision used to build every new MAYTAG ®appliance. To locate factory specified parts in your area, call the following customer assistance telephone number or your nearest designated service center. and Service Call Maytag Services, LLC Customer Assistance toll free: 1-800-688-9900, or visit our website at www.amana.com/help provide assistance with: • Features and specifications • Installation information. on our full line of appliances. • Use and maintenance • Accessory • Specialized customer assistance (Spanish speaking, hearing impaired, limited vision, etc.). • Referrals to local dealers, repair parts distributors and service companies. Maytag ®appliances designated service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States. procedures. and repair parts sales. To locate the Maytag ®appliances designated service company in your area, you can also look in your telephone directory Yellow Pages. For further assistance If you need further assistance, you can write to Maytag ® appliances with any questions or concerns at: Maytag Services, LLC Attn: CAIR _ Center P.O. Box 2370 Cleveland, TN 37320-2370 Please include a daytime phone number in your correspondence. 27 AMANA ®LAUNDRY WARRANTY LIMITED WARRANTY For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Amana brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Amana") will pay for factory specified parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be provided by a Amana designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain service under this limited warranty. ITEMS EXCLUDED FROM WARRANTY This limited warranty does not cover: 1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a manner that is inconsistent to published user or operator instructions and/or installation instructions. 2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing. 3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Amana. 4. 5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Amana within 30 days from the date of purchase. 6. Pick up and delivery. This major appliance is intended to be repaired in your home. 7. Repairs to parts or systems resulting from unauthorized modifications 8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Amana servicer is not available. made to the appliance. 9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Amana's published installation instructions. 10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined. DISCLAIMER OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province. LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. AMANA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province. If outside the 50 United States and Canada, contact your authorized Amana dealer to determine if another warranty applies. If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Amana. In the U.S.A., call 1-800-688-9900. In Canada, call 1-800-807-6777. 6/o8 Keep this book and your sales slip together for future reference. You must provide proof of purchase or installation date for in-warranty service. Write down the following information about your major appliance to better help you obtain assistance or service if you ever need it. You will need to know your complete model number and serial number. You can find this information on the model and serial number label located on the product. Dealer name Address Phone number Model number Serial number Purchase date W10216186A © 2008 All rights reserved. ®Registered trademarW TM Trademark of Maytag Corporation or its related companies. 7/08 Printed in U.S.A.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project