Mega Lite | 4070-N-E | User manual | Mega Lite 4070-N-E User manual

USER MANUAL
Table of Contents
Safety Information……………………………………………………………………………………………. 3
Specifications……………………………………………………………………………………………………..4
Main Power Connection…………………………………………………………………………………..5
DMX-512 Connection…………………………………………………………………...……………...... 5
DMX Profile......................................................................................................................... 6
Main Control Menu.......................................................................................................... 7
Rigging the Fixture…………………………………………………………………………………………….9
Cleaning & Maintenance................................................................................................9
Parts List.............................................................................................................................. 9
Check that the unit has not been damaged during transport
Protection Against Fire
1.
3.
4.
5.
6.
Maintain a minimum of 1 foot distance from any type of flame.
Replace fuse only with the specified type and rating.
Do Not install the unit to close to a heat source.
Make sure cable are properly secured away from unit movement.
Maximum surface operating temperature 80º.
Protection Against Fire
1.
2.
3.
4.
Disconnect power before servicing.
For connection to main power supply proceed to page 5.
This unit must be earthed. (electronically grounded)
Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3
Technical Information
Part Numbers
Fixture
4070-N-E Color Punch
Mechanical Specifications
DMX Connectors:
10.25”
3-pin XLR connectors in/out
Power Connections: Neutrik Power Con in/out
Thermal:
Maximum ambient temperature 40° C
Maximum surface temperature 60° C
Display:
Digital
Fastening System:
Mounting Yoke
Fixture
7.75”
9.25”
Packaged for Shipping
Size: 10.25”L x 3.5”W x 9.25”H
Size: 11.75 X 6.5 X 12
Weight: 5 lbs
Weight: 6 lbs
8.25”
Electrical Specifications
LED Quantity:
Red:
Green:
Blue:
12 Tri Color
12
12
12
LED Watts: 3
LED Lifetime: 60,000 to 100,000 hours
LED Angle: 25°
Power Consumption: Universal 100 - 240V 50/60 Hz
Ballast: Electronic
Watts:
Amps:
38
.43
Control & Programming
Protocol: DMX 512
DMX Channels:
3 Mode of operation
Mode A
Mode P
Mode F
Operating mode:
3 Channel R, G, B
4 Channel Dimmer/Strobe, R, G, B
7 Channel R,G,B, CTO, Strobe, Dimmer
Stand alone
4
3.5”
Main Power Connection
Caution!
1.
2.
3.
4.
Do not connect fixture to a dimmer system.
This unit has Auto switching power supply. It will respond to 110V or 220V automatically
This unit must be earthed. (electronically grounded)
Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to 60Hz
Cable (USA)
Cable (EU)
Pin
110V
220V
Black
Brown
Live
L
L
White
Light Blue
Neutral
N
L
Green
Yellow/Green
Ground
220V
Connection
L
N
L
110V
Connection
L
DMX-512 Connection
The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded
twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller with the fixture or
the fixture with another.
DMX—output
DMX—input
1. Shield
2. Signal (-)
2
2
1
1
3. Signal (+)
3
3
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a 120
Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it in to the
last fixture on the signal run. Pre-manufactured terminator plugs are available for
purchase from your Mega-Lite dealer (HOS-DMXT).
5
N-E Color Punch Mode A
DMX Chanel
1
2
3
Function
LED Color
LED Color
LED Color
Description
Red LED intensity
Green LED Intensity
Blue LED Intensity
Value
0-255
0-255
0-255
Description
Dimmer
Strobe (slow to fast)
Random Strobe (slow to fast)
Dimmer Full On
Red LED intensity
Green LED Intensity
Blue LED Intensity
Value
0-152
153-196
197-242
243-255
0-255
0-255
0-255
Description
Red LED intensity
Green LED Intensity
Blue LED Intensity
3200K
3800K
4400K
5000K
5600K
6200K
7000K
Strobe (slow to fast)
Random Strobe (slow to fast)
No Function
Color fade (slow to fast)
Color Snap (slow to fast)
Random (slow to fast)
Yellow
Purple
Aqua
Orange
Red Pulse
green Pulse
Blue Pulse
Yellow Pulse
Aqua Pulse
White Pulse
White LED Full
Dimmer Off to Full
Value
0-255
0-255
0-255
0-36
37-73
74-110
111-147
147-183
184-220
221-256
0-196
197-255
0-1
2-19
20-39
40-59
60-79
80-99
100-119
120-139
140-159
160-179
180-199
200-219
220-229
230-249
250-255
0-255
N-E Color Punch Mode P
DMX Chanel
Function
1
Dimmer
2
3
4
LED Color
LED Color
LED Color
N-E Color Punch Mode F
DMX Chanel
1
2
3
Function
LED Color
LED Color
LED Color
4
CTO
5
Strobe
6
Macro
7
Dimmer
6
Main Control Menu
CONTROL BOARD
The control board on the fixture base is your interface to access and control
all the functions on the unit. Its digital display gives you a code view of the
options and functions. The following will explain each function and its options.
Menu
DMX Address
1-512
Fade Scroll
A-P-F
Red Dimmer
Green Dimmer
Blue Dimmer
0-15
0-15
0-15
Flash
Fade Scroll
0-15
0-15
Up
Down
Flash Scroll
Chase Effect
Chase Speed
0-15
0-15
0-15
Enter
DMX Address
Press Enter to select. Use the up/down keys to select the required DMX start channel. Press Enter to confirm
Channel Mode
Mode A (3 Channels) R,G,B
This function allows you to select the operating mode
of the DMX channel profile. Press Enter use the up/
down keys to select desired Mode settings. Press
Enter to confirm the settings.
Mode P (4 Channels) Dimmer/ Strobe ,R,G,B
Mode F (7 Channels) R,G,B, CTO, Strobe, Macro, Dimmer
Red Dimmer
This function allows you to dim the red LED’s on the whole module. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings. (15 Steps)
Green Dimmer
This function allows you to dim the green LED’s on the whole module. Press Enter use the up/down keys to select desired dimmer settings. Press Enter to confirm the settings. (15 Steps)
Blue Dimmer
This function allows you to dim the blue LED’s on the whole module. Press Enter use the up/down keys to select desired dimmer
settings. Press Enter to confirm the settings. (15 Steps)
7
Flash
This function allows you to strobe the LED’s on the whole module in White color. Press Enter use the up/down keys to select
desired flash settings. Press Enter to confirm the settings.
Fade Scroll
This function allows you to fade the LED’s on the whole module from one color to another. Press Enter use the up/down keys to
select desired fade speed settings. Press Enter to confirm the settings. (15 Steps)
Flash Scroll
This function allows you to change the LED’s on the whole module from one color to another. Press Enter use the up/down keys
to select desired color change speed settings. Press Enter to confirm the settings. (15 Steps)
Chase Effect
This function allows you to select different chase patterns on the whole module. Press Enter use the up/down keys to select
desired chase settings. Press Enter to confirm the settings.
Chase Speed
This function allows you to select the speed of the chase that was selected on the Chase Effect . Press Enter use the up/down
keys to select desired chase speed settings. Press Enter to confirm the settings.
8
Rigging the fixture
Caution!
1.
2.
3.
4.
The installations must be carried out by an authorized dealer or trained professional.
Unit may cause severe injures if you have doubts concerning the safety do not install.
Unit is to be 24inches away from flammable materials (decoration material)
Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the projector has got to
be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be checked at least
one time a year by a skilled person.
Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installations and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments. Further
instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems
have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried
out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by authorized dealers or
trained professional only.
Should you have further questions , please contact your dealer.
Parts List
4070-FAN
Replacement fan
4070-MPCB
Main PCB card
4070-PS
Power Supply
4070-DIS
Display
4070-FH
Fuse Holder
4070-TRILED
Tri Chip LED
4070-KNOB
Knob Set
9
Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax 210-855-6279
www.mega-lite.com / info@mega-lite.com
Download PDF

advertising