Christie | 38-VIV403-01 | User`s manual | Christie 38-VIV403-01 User`s manual

MODEL
38-VIV403-01
✽ Projection lens is optional.
User's Manual
Downloaded From projector-manual.com Christie Manuals
TO THE OWNER
Before operating this projector, read this manual thoroughly and operate the projector properly.
This projector provides many convenient features and functions. Operating the projector properly enables you to
manage those features and maintains it in better condition for a considerable time.
Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other
accidents.
If your projector seems to operate improperly, read this manual again, check operations and cable connections and try
the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales
dealer where you purchased the projector or the service center.
SAFETY PRECAUTIONS
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
● This projector produces intense light from the projection lens. Do not stare directly into the lens. Eye damage
could result. Be especially careful that children do not stare directly into the beam.
● This projector should be set in the way indicated. If not, it may result in a fire hazard.
● Take appropriate space on the top, sides and rear of the projector
cabinet for allowing air circulation and cooling the projector.
Minimum distance should be taken. If the projector is to be built
into a compartment or similarly enclosed, the minimum distances
must be maintained. Do not cover the ventilation slot on the
projector. Heat build-up can reduce the service life of your
projector, and can also be dangerous.
SIDE and TOP
REAR
20cm
50cm
50cm
1m
● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation
holes.
● Remote Control Unit, supplied to this projector, emits the laser beam as the laser pointer function from Laser
Light Window while pressing LASER button (for 1 minute / LASER POINTER INDICATOR lights red to indicate
laser emission). Do not look into Laser Light Window or shine the laser beam on yourself or other people. Eye
damage may result.
● If the projector is not to be used for an extended time, unplug the projector from the power outlet.
READ AND KEEP THIS USER'S MANUAL FOR LATER USE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION :
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT DANGEROUS
VOLTAGE CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS UNIT.
2
Downloaded From projector-manual.com Christie Manuals
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS IN THE
USER'S MANUAL WITH THIS UNIT.
SAFETY INSTRUCTIONS
All the safety and operating instructions should be read before
the product is operated.
Read all of the instructions given here and retain them for later
use. Unplug this projector from AC power supply before
cleaning. Do not use liquid or aerosol cleaners. Use a damp
cloth for cleaning.
This projector should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supplied, consult your authorized dealer or
local power company.
Follow all warnings and instructions marked on the projector.
Do not overload wall outlets and extension cords as this can
result in fire or electric shock. Do not allow anything to rest on
the power cord. Do not locate this projector where the cord
may be damaged by persons walking on it.
For added protection to the projector during a lightning storm,
or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This will prevent damage
due to lightning and power line surges.
Do not attempt to service this projector yourself as opening or
removing covers may expose you to dangerous voltage or
other hazards. Refer all servicing to qualified service
personnel.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool, etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand, or table.
The projector may fall, causing serious injury to a child or
adult, and serious damage to the projector. Use only with a
cart or stand recommended by the manufacturer, or sold with
the projector. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit
approved by the manufacturers.
An appliance and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
Slots and openings in the back and bottom of the cabinet are
provided for ventilation, to insure reliable operation of the
equipment and to protect it from overheating.
Unplug this projector from wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet has been
damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer that have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock, or injury to persons.
Upon completion of any service or repairs to this projector, ask
the service technician to perform routine safety checks to
determine that the projector is in safe operating condition.
The openings should never be covered with cloth or other
materials, and the bottom opening should not be blocked by
placing the projector on a bed, sofa, rug, or other similar
surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation
such as a book case unless proper ventilation is provided.
Never push objects of any kind into this projector through
cabinet slots as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the projector.
Downloaded From projector-manual.com Christie Manuals
Voor de klanten in Nederland
Bij dit product zijn batterijen
geleverd.
Wanneer deze leeg zijn,
moet u ze niet weggooien
maar inleveren als KCA.
3
COMPLIANCES
Federal Communication Commission Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such
changes or modifications should be made, you could be required to stop operation of the equipment.
CAUTION!
This is a Class A equipment. This equipment can cause interference in residential areas; in this case, the operator
can be asked to take adequate countermeasures.
AC POWER CORD REQUIREMENT
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada :
AC Power Cord used in the United States and Canada is listed by the Underwriters
Laboratories (UL) and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure
that the plug will fit into the power outlet. Do not try to defeat this safety feature.
Should you be unable to insert the plug into the outlet, contact your electrician.
GROUND
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
4
Downloaded From projector-manual.com Christie Manuals
TABLE OF CONTENTS
FEATURES AND DESIGN
PREPARATION
6
7
COMPUTER MODE
SELECTING INPUT SOURCE
SELECTING COMPUTER SYSTEM
COMPATIBLE COMPUTER SPECIFICATIONS
PC ADJUSTMENT
NAME OF EACH PART OF PROJECTOR
SETTING-UP PROJECTOR
7
8
CONNECTING AC POWER CORD
LENS INSTALLATION
POSITIONING PROJECTOR
LENS SHIFT ADJUSTMENT
PICTURE LEVEL AND TILT ADJUSTMENT
MOVING PROJECTOR
8
9
9
9
10
10
AUTO PC ADJUSTMENT
MANUAL PC ADJUSTMENT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
VIDEO MODE
CONNECTING PROJECTOR
11
TERMINALS OF PROJECTOR
CONNECTING TO COMPUTER
CONNECTING TO VIDEO EQUIPMENT
11
14
15
SELECTING INPUT SOURCE
SELECTING VIDEO SYSTEM
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT
IMAGE LEVEL ADJUSTMENT
PICTURE SCREEN ADJUSTMENT
BEFORE OPERATION
SIDE CONTROLS AND INDICATORS
OPERATION OF REMOTE CONTROL
LASER POINTER FUNCTION
REMOTE CONTROL BATTERIES INSTALLATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
FLOW OF ON-SCREEN MENU OPERATION
MENU BAR
BASIC OPERATION
TURNING ON / OFF PROJECTOR
ADJUSTING SCREEN
ZOOM ADJUSTMENT
FOCUS ADJUSTMENT
LENS SHIFT ADJUSTMENT
KEYSTONE ADJUSTMENT
PICTURE FREEZE FUNCTION
NO SHOW FUNCTION
P-TIMER FUNCTION
SOUND ADJUSTMENT
26
26
26
28
29
29
30
32
32
33
34
35
35
36
37
37
38
39
16
16
18
18
19
20
20
20
21
22
22
23
23
23
23
23
24
24
24
SETTING
SETTING MENU
APPENDIX
OPERATING WIRELESS MOUSE
MAINTENANCE
40
40
43
43
43
WARNING TEMP. INDICATOR
AIR FILTER CARE AND CLEANING
CLEANING PROJECTION LENS
LAMP MANAGEMENT
LAMP REPLACEMENT
43
44
44
45
46
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
48
50
25
TRADEMARKS
● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc.
● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc.
● Windows and PowerPoint are registered trademarks of Microsoft Corporation.
● Each name of corporations or products in the user's manual is a trademark or a registered trademark of its
respective corporation.
Downloaded From projector-manual.com Christie Manuals
5
FEATURES AND DESIGN
This Multimedia Projector is designed with most advanced technology for portability, durability, and ease of use. This
projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD)
technology.
◆
Compatibility
This projector widely accepts various video and
computer input signals including;
● Computers
IBM-compatible or Macintosh computer up to 1600
x 1200 resolution.
● 6 Color Systems
NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PALN color system can be connected.
● Component Video
Component video signal, such as a DVD player
output high definition TV signals including 480i,
480p, 575i, 575p, 720p, 1035i, 1080i-50 or 1080i60, can be connected.
● S-Video
S-Video signal, such as a S-VHS VCR output
signal, can be connected.
◆
High Resolution Image
This projector provides 1600 x 1200 dots resolution for
computer input and 1100 horizontal TV lines. This
projector cannot display image of over 1600 x 1200 dots.
When resolution of your computer is over than 1600 x
1200, reset a computer output for lower resolution.
◆
Multi-Scan System
This projector has Multi-Scan System to conform to
almost all computer output signals quickly. There is no
need for troublesome manual adjustment of frequency
and other settings.
◆
One-Touch Auto PC Adjustment
Incoming computer video signals are recognized and
best adjustment is automatically set by Auto PC
Adjustment. No complicated setup is necessary and
projection is always precise.
◆
Progressive Scan Function
This function converts interlace video signals into
progressive scan signals and provide fine picture quality.
◆
Digital Zoom (for Computer)
Digital Zoom function adjusts image size to approx. 1/4 ~
49 times of original image size, allowing you to focus on
crucial information at a presentation.
◆
Keystone Correction
Positioning height of a projector may result in distorted
image being displayed in a trapezoid shape. Keystone
Correction solves this problem by digitally altering
projection to produce undistorted images.
6
Downloaded From projector-manual.com Christie Manuals
◆
Motor-driven Lens Shift
Projection lens can be moved up, down left and right with
motor-driven lens shift function. This function makes it
easy to provide projected image where you want.
Zoom and focus can be also adjusted with motor-driven
operation.
◆
Power Management
Power Management function is provided to reduce power
consumption while a projector is not in use.
This Power Management function operates to turn
Projection Lamp off when a projector detects signal
interruption and any button is not pressed over 5
minutes. Projection Lamp is automatically turned on
again when a projector detects signal or any operation
button is pressed.
This projector is shipped with this function ON.
◆
Digital Visual Interface
This projector is equipped with DVI 29-pin terminal for
connecting DVI output from a computer.
◆
Multi Versatile Platform
This projector applies various input/output terminals and
4 terminal slots for expansion to tune to diversity of
signals from computers and video equipment.
◆
Selectable Terminal Slots
4-built-in Terminal Slots enable you to arrange any
combinations of input sources just by changing Terminal
Boards. For Terminal Boards, contact sales dealer
where you purchased a projector.
◆
Laser Pointer Function
Remote Control Unit supplied with this projector includes
Laser Pointer function. This function helps you to make
a smart presentation on a projected screen.
◆
Wireless Mouse
Remote Control Unit supplied with this projector has
Wireless Mouse function for a connected computer. This
function enables you to operate both projector and
computer with Remote Control Unit only.
◆
Multilanguage Menu Display
Operation menu is displayed in; English, German,
French, Italian, Spanish, Portuguese, Dutch, Swedish,
Russian, Chinese, Korean or Japanese.
◆
Network board (Optional)
Network board is an optional product to control and set
up a projector via the network cable. By accessing to the
connected projector using the web browser on your
computer. It can be controlled and set up the projector
remotely. Contact the sales dealer where you purchased
this projector for optional parts.
PREPARATION
NAME OF EACH PART OF PROJECTOR
FRONT OF CABINET
SPEAKERS
INFRARED
REMOTE RECEIVER
POWER CORD
CONNECTOR
PROJECTION LENS
MAIN ON / OFF
SWITCH
LENS COVER
CAUTION
Do not turn on a projector with lens cover
attached. High temperature from light beam may
damage lens cover and result in fire hazard.
CARRYING HANDLE
LEVEL AND TILT ADJUST HANDLE
BACK OF CABINET
EXHAUST VENT
INFRARED
REMOTE RECEIVER
HOT AIR EXHAUSTED !
Air blown from exhaust vent is hot. When
using or installing a projector, following
precautions should be taken.
● Do not put a flammable object near this vent.
● Keep rear grills at least 3’ (1m) away from
any object, especially heat-sensitive object.
● Do not touch this area, especially screws
and metallic parts. This area will become
hot while a projector is used.
This projector detects internal temperature
and automatically controls operating power
of Cooling Fans.
LAMP COVER
BOTTOM OF CABINET
AIR FILTER
AIR INTAKE VENTS
This projector is equipped with cooling
fans for protection from overheating.
Pay attention to following to ensure
proper ventilation and avoid a possible
risk of fire and malfunction.
● Do not cover vent slots.
● Keep bottom clear of any objects.
Obstructions may block cooling air.
ADJUSTABLE FEET
ADJUSTABLE FEET
Downloaded From projector-manual.com Christie Manuals
7
PREPARATION
SETTING-UP PROJECTOR
CONNECTING AC POWER CORD
This projector uses nominal input voltages of 120 V or
200-240 V AC. This projector automatically selects
correct input voltage. It is designed to work with singlephase power systems having a grounded neutral
conductor. To reduce risk of electrical shock, do not plug
into any other type of power system.
Consult your authorized dealer or service station if you
are not sure of type of power supply being in use.
Connect a projector with peripheral equipment before
turning a projector on. (Refer to pages 12 ~ 15 for
connection.)
Connect AC Power Cord (supplied) to
a projector.
AC outlet must be near this equipment
and must be easily accessible.
CAUTION
AC Power Cord must meet requirement of country where you use a projector.
Confirm AC plug type with chart below and proper AC power cord must be used.
If supplied AC Power Cord does not match AC outlet, contact your sales dealer.
AC Outlet side
Projector side
For U.S.A. and Canada
For Continental Europe
Ground
To POWER CORD
CONNECTOR on a
projector.
8
Downloaded From projector-manual.com Christie Manuals
To AC Outlet.
(120 V AC)
To AC Outlet.
(200 - 240 V AC)
PREPARATION
LENS INSTALLATION
Before setting up a projector, install Projection Lens on a Projector.
1. Before installation, check where a projector is used and prepare suitable lens. For specifications of Projection
Lens, refer to manual separately attached or contact sales dealer where you purchased a projector.
2. For installation, refer to installation manual supplied to a Projector.
When moving or setting up a projector, be sure to replace a Lens Cover to protect a surface. And be
careful not to hold or subject a lens to strong forces. It may damage lens, cabinet, or mechanical
parts.
POSITIONING PROJECTOR
This projector is designed to project on a flat projection
surface.
SCREEN
ROOM LIGHT
Brightness in room has a great influence on picture
quality. It is recommended to limit ambient lighting in
order to provide best image.
VENTILATION
This projector is equipped with cooling fan to protect it from overheating. Pay attention to following to ensure proper ventilation
and avoid a possible risk of fire and malfunction.
● Do not cover vents with papers or other materials.
● Keep rear grill at least 3 feet (1 m) away from any
object.
● Make sure that there are no objects under a projector.
An object under a projector may prevent a projector
from taking cooling air through bottom vent.
AIR INTAKE VENT
(BOTTOM SIDE)
EXHAUST VENT
(REAR SIDE)
LENS SHIFT ADJUSTMENT
Projection lens can be moved up, down, left and right with motor-driven lens shift function. This function makes
it easy to provide projected image where you want.
Use LENS SHIFT button and
POINT UP/DOWN button to
move image up or down.
(Refer to page 23.)
Use LENS SHIFT button and
POINT LEFT/RIGHT button to
move image left or right.
(Refer to page 23.)
MOVED UP OR DOWN
Downloaded From projector-manual.com Christie Manuals
MOVED LEFT OR RIGHT
9
PREPARATION
PICTURE LEVEL AND TILT ADJUSTMENT
Picture tilt and projection angle can be adjusted with
handles on both sides of a projector. Projection angle
can be adjusted to 5.7 degrees upper way.
1
Press knob on handle. Handle pop out.
2
Turn handles (right and left) until picture is projected on
proper position. Adjust height of rear adjustable feet by
rotating them until projector properly stabled on table.
3
Press knob and retract handle.
REAR ADJUSTABLE
FEET. (Refer to P7).
LEVEL AND TILT
ADJUST HANDLE
KNOB
ADJUSTABLE
FEET
Height of front feet can be adjusted
by turning handles.
MOVING PROJECTOR
For safety, be sure to hold Carrying Handles
on both sides by 2 or more people when
moving a projector. Moving it unproperly may
result in damage of cabinet or person's
injury.
Replace lens cover and retract feet to prevent damage to lens and cabinet.
1
Pull up lock buttons on each side of carrying handles
and release locks.
2
Pull carrying handles out fully until it's locked (with a
click). Move a projector by holding two handles by 2 or
more people.
3
To retract carrying handles, pull up lock buttons and
release lock of handles and press handles fully in until
it's locked.
CARRYING
HANDLE
LOCK BUTTONS
Pull up lock buttons to
release lock.
CAUTION IN CARRYING OR TRANSPORTING A PROJECTOR
● Do not drop or bump a projector, otherwise damages or malfunctions may result.
● When carrying a projector, use a suitable carrying case.
● Do not transport a projector by using a courier or transport service in an unsuitable transport case. This
may cause damage to a projector. To transport a projector through a courier or transport service, consult
your dealer and best case should be applied.
10
Downloaded From projector-manual.com Christie Manuals
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector.
4 TERMINAL SLOTS (Factory set)
SERIAL PORT OUT
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
R
INPUT 1
(MONO)
DVI Terminal
INPUT 2
CONTROL PORT
5 BNC Terminal
INPUT 3
AUDIO
L
R
DVI
AV Terminal
INPUT 4
SERIAL PORT IN
HDB 15-PIN
Terminal
CONTROL PORT
L
(MONO)
R/C JACK
USB
VIDEO/Y
C
S-VIDEO
AUDIO
R
L
(MONO)
INPUT/OUTPUT
TERMINALS
AUDIO OUT
R
ANALOG RGB
L
RESET
AUDIO
R
CONTROL PORT
L
(MONO)
(MONO)
REPLACEMENT OF TERMINAL
NOTE; When replacement of terminal board, MAIN
ON/OFF switch should be OFF position.
1
Remove 2 Screws on terminal.
2
Pull out terminal by holding handle.
3
Replace terminal. Insert terminal along Guide to fit Plug
into Socket.
4
Tighten screws to secure terminal.
Screws
NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD
Guide
Socket
When ordering or using Optional Interface Board
(Terminal Board), contact your sales dealer. When contacting the sales dealer, tell the Optional Control
Number (Op.cont.No.) in the menu that is located under
Language Select Menu. (See page 40.)
Figure shows HDB 15-PIN terminal.
Plug
Downloaded From projector-manual.com Christie Manuals
11
CONNECTING PROJECTOR
INPUT/OUTPUT TERMINALS AND JACKS
INPUT 1
INPUT 1, 2, 3, 4
DVI INPUT TERMINAL
5 BNC INPUT JACKS
Connect component video output (Cr, Y,
Cb or Pr, Y, Pb) from video equipment to
R/Pr, G/Y and B/Pb jacks or connect
computer output [5 BNC Type (Red,
Green, Blue, Horiz. Sync and Vert.
Sync.)] from computer to R/Pr, G/Y,
B/Pb, H/HV and V jacks. (Refer to P14,
15)
SERIAL PORT IN
AUDIO INPUT JACKS
Connect computer output
(Digital/Analog DVI-I type)
to this terminal.
(Refer to P14.)
AUDIO
L
R
DVI
CONTROL PORT
(MONO)
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
R
CONTROL PORT
INPUT 2
SERIAL PORT OUT
Connect audio output
from computer or video
equipment to these jacks.
(Refer to P14, 15.)
INPUT 1
INPUT 2
L
INPUT 1, 2, 4
CONTROL PORT CONNECTORS
(MONO)
USB
S-VIDEO
C
VIDEO/Y
AUDIO
R
INPUT 3
R/C JACK
L
(MONO)
AUDIO OUT
ANALOG RGB
L
RESET
AUDIO
R
CONTROL PORT
L
(MONO)
INPUT 4
R
When controlling computer
with Remote Control of this
projector, connect mouse port
of your personal computer to
these connectors. (Refer to
P14.)
(MONO)
INPUT 3
12
INPUT 4
INPUT 3
AV INPUT (VIDEO/Y, C) JACKS
HDB 15-PIN INPUT TERMINAL
S-VIDEO INPUT JACK
Connect composite video output from
video equipment to VIDEO/Y jack or
connect Separate Y/C video outputs to
VIDEO/Y and C jacks. (Refer to P15.)
Connect computer output
(Analog HDB 15-pin type) to
this terminal.
(Refer to P14.)
Connect S-VIDEO output
from video equipment to
this jack. (Refer to P15.)
Downloaded From projector-manual.com Christie Manuals
CONNECTING PROJECTOR
USB PORT (Series B)
SERIAL PORT
IN TERMINAL
This port is used to control a projector
with computer. It is also used to
control computer with Remote Control
of this projector. (Refer to P41-43.)
Connect USB port of computer to this
port.
If you control a projector by computer,
you must connect a cable (not provided)
from your computer to this terminal.
SERIAL PORT
OUT TERMINAL
AUDIO
L
R
DVI
CONTROL PORT
(MONO)
SERIAL PORT OUT
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
R
INPUT 1
SERIAL PORT IN
CONTROL PORT
INPUT 2
This terminal outputs signal
from SERIAL PORT IN. More
than two projectors can be
controlled with one computer
by connecting SERIAL PORT
IN. of another projector to this
terminal.
L
(MONO)
USB
VIDEO/Y
C
S-VIDEO
AUDIO
R
L
INPUT 3
R/C JACK
(MONO)
AUDIO OUT
ANALOG RGB
L
RESET
R
CONTROL PORT
L
(MONO)
INPUT 4
R
AUDIO
(MONO)
RESET BUTTON
R/C JACK
When using Wired / Wireless Remote
Control Unit as Wired Remote
Control, Connect Wired Remote
Control Unit to this jack with Remote
Control Cable (supplied).
(Refer to page 19.)
This projector uses a micro processor to control unit.
Occasionally, micro processor may malfunction and
need to be reset. This can be done by pressing
RESET button with a pen, which will shut down and
restart unit. Do not use RESET function excessively.
AUDIO OUTPUT JACKS
Connect an external audio
amplifier to these jacks.
(Refer to P14, 15.)
Downloaded From projector-manual.com Christie Manuals
13
CONNECTING PROJECTOR
CONNECTING TO COMPUTER
Cables used for connection (✽ = Cables are not supplied with this projector.)
• VGA Cable (HDB 15 pin)
NOTE :
• Control Cable for PS/2 port, Serial port, or ADB port
When connecting cable, power cords of both a
• MAC/VGA Adapter, DVI/VGA Adapter
projector and external equipment should be
disconnected from AC outlet. Turn a projector
• DVI Cable
and peripheral equipment on before computer is
• BNC Cable (BNC x 5) ✽
switched on.
• Audio Cables (RCA x 2) ✽
IBM-compatible computers or Macintosh computers (VGA / SVGA / XGA / SXGA/UXGA)
Desktop type
Monitor Output
Laptop type
Monitor Output Audio Output Serial port
Monitor Output
PS/2 port
ADB port
MAC/VGA
Adapter
Set slide switches
following chart
below.
BNC Cable ✽
Control Cable Control Cable Control Cable
for Serial Port for PS/2 Port for ADB Port
Audio Cable
(stereo) ✽
DVI Cable
Terminal
Terminal
Terminal
DVI/VGA Adapter
VGA Cable
Use one of these Control
Cables corresponding
with terminal of your
computer.
AUDIO
L
R
DVI
CONTROL PORT
INPUT 1
SERIAL PORT IN
(MONO)
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
R
CONTROL PORT
INPUT 2
SERIAL PORT OUT
L
(MONO)
USB
VIDEO/Y
C
S-VIDEO
AUDIO
R
L
INPUT 3
Terminals of
a Projector
R/C JACK
(MONO)
AUDIO OUT
ANALOG RGB
L
RESET
AUDIO
R
CONTROL PORT
INPUT 4
R
L
(MONO)
(MONO)
MAC/VGA ADAPTER
AUDIO OUT
ON
Audio Cable
(stereo) ✽
Switches of
MAC/VGA Adapter
ON
DIP
1 2 3 4 5 6
OFF
Audio Input
External Audio Equipment
Audio Amplifier
14
Downloaded From projector-manual.com Christie Manuals
Audio Speaker
(stereo)
Set switches as shown in table below depending on
RESOLUTION MODE that you want to use before
your turn on a projector and computer
MODE
SWITCHES
1
2
3
4
5
6
13"MODE (640 x 480)
ON
ON OFF OFF OFF OFF
16"MODE (832 x 624)
OFF ON OFF ON OFF OFF
19"MODE (1024 x768)
OFF ON
ON OFF OFF OFF
21"MODE (1152 x 870)
ON
ON
ON
ON OFF OFF
CONNECTING PROJECTOR
CONNECTING TO VIDEO EQUIPMENT
Cables used for connection
NOTE :
When connecting cable, power cords of both a
projector and external equipment should be
disconnected from AC outlet. Turn a projector
and peripheral equipment on before computer is
switched on.
• Video Cable (BNC x 1, BNC x 2 or BNC x 3) ✽
• S-VIDEO Cable ✽
• Audio Cable (RCA x 2) ✽
(✽ = Cables are not supplied with this projector.)
Component video output equipment.
Video Source (example)
Video Cassette Recorder
Separate Y/C
Video Output
Y
Component Video Output
Pr/Cr
Y
S-VIDEO Output
Pb/Cb
Audio Output
R
L
C
Video
Cable ✽
Video
Cable ✽
S-VIDEO
Cable ✽
Video
Cable ✽
S-VIDEO
AV AUDIO IN
Pr/Cr-Y-Pb/Cb
Y-C
VIDEO
Audio Cable
(Stereo) ✽
SERIAL PORT IN
AUDIO
L
R
DVI
CONTROL PORT
(MONO)
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
R
CONTROL PORT
INPUT 2
SERIAL PORT OUT
INPUT 1
Composite
Video Output
(such as DVD player or
high-definition TV source.)
Video Disc Player
L
(MONO)
USB
VIDEO/Y
C
S-VIDEO
AUDIO
R
L
INPUT 3
R/C JACK
(MONO)
Terminals of
a Projector
AUDIO OUT
ANALOG RGB
L
RESET
AUDIO
R
CONTROL PORT
L
(MONO)
INPUT 4
R
(MONO)
AUDIO OUT
Audio Cable
(Stereo) ✽
Audio Input
External Audio Equipment
Audio Amplifier Audio Speaker (stereo)
Downloaded From projector-manual.com Christie Manuals
15
BEFORE OPERATION
SIDE CONTROLS AND INDICATORS
REAR
INDICATORS
SIDE CONTROLS
FRONT
INDICATORS
SIDE CONTROLS
ZOOM BUTTONS
FOCUS BUTTONS
VOLUME BUTTONS
POWER ON–OFF BUTTON
Used to adjust zoom.
(P23)
Used to adjust focus. (P23)
Used to adjust volume.
(P25)
Used to turn a projector on
or off. (P22)
ZOOM
FOCUS
VOLUME
ON-OFF
MENU BUTTONS
LENS SHIFT BUTTONS
Used to open or close MENU
operation. (P20, 21)
Used to select LENS
SHIFT function. (P23)
SELECT BUTTON
LENS SHIFT
MENU
Used to execute item
selected. It is also used to
expand image in DIGITAL
ZOOM mode. (P34)
INPUT 3/4
SELECT
INPUT 1/2 BUTTON
Used to select input source
either INPUT 1 or INPUT 2.
(P26)
AUTO PC ADJ. BUTTON
INPUT 3/4 BUTTON
Use to operate AUTO PC
Adjustment function. (P29)
Used to select input source
either INPUT 3 or INPUT 4.
(P26)
AUTO PC ADJUST
POINT BUTTONS
Used to select an item or
adjust value in MENU. It is
also used to pan image in
DIGITAL ZOOM mode.
(P34)
16
INPUT 1/2
Downloaded From projector-manual.com Christie Manuals
IMAGE
IMAGE BUTTON
Used to select image
level. (P32, 37)
BEFORE OPERATION
INDICATORS
FRONT INDICATORS
LAMP
READY
LAMP
REPLACE
WARNING
TEMP.
LAMP REPLACE INDICATOR
WARNING TEMP. INDICATOR
This LAMP REPLACE
indicator lights yellow when
any of Projection Lamps is
nearing its end, and flashes
when any of them becomes
out. Check which lamp
needs to be replaced on
Lamp Status Display.
(P45-47)
This indicator flashes red
when internal projector
temperature is too high.
(P43)
READY INDICATOR
LAMP INDICATOR
This indicator lights green
when a projector is ready to
be turned on. And it
flashes green in Power
Management mode. (P41)
This indicator is dim when a
projector is turned on. And
bright when a projector is in
stand-by mode.
LAMP
READY
WARN
ING
TEMP
.
LA P
REPLM
ACE
REAR INDICATORS
Downloaded From projector-manual.com Christie Manuals
17
BEFORE OPERATION
OPERATION OF REMOTE CONTROL
Left Side
LASER POINTER INDICATOR
POWER ON-OFF BUTTON
ON
Lights red while laser beam
is emitted from Laser Light
Window.
ON-OFF
Used to turn projector on or
off. (P22)
INPUT 1/2 BUTTON
ZOOM
FOCUS VOLUME
LOCK
F
ALL OF
MUTE D.ZOOM INPUT 1/2
MENU BUTTON
Used to select MENU
operation. (P20, 21)
MENU
INPUT 3/4
Used to select input source
either INPUT 1 or INPUT 2.
(P26)
INPUT 3/4 BUTTON
Used to select input source
either INPUT 3 or INPUT 4.
(P26)
POINT BUTTON
SELECT BUTTON
ALL-OFF SWITCH
When using Remote Control Unit,
turn this switch to “ON.” And turn it
to “ALL OFF” when it is not used.
Used to execute item
selected, or to expand
or compress image in
DIGITAL ZOOM +/–
mode. (P34)
It is also used as a PC
mouse in Wireless
Mouse Operation. (P43)
LASER BUTTON
Used to operate Laser
Pointer Function. Laser
beam is emitted while
pressing this button within
1 minute.
When using this Laser
Pointer for more than 1
minute, release LASER
button and press it again.
LASER
LENS SHIFT
KEYSTONE
NO SHOW
FREEZE
AUTO PC ADJ.
IMAGE
P-TIMER
Used to move a pointer on
ON-SCREEN MENU, adjust
each item, or pan image in
DIGITAL ZOOM +/– mode.
(P34)
It is also used as a PC mouse
in Wireless Mouse Operation.
(P43)
✽ When pressing center of this
button, it works as SELECT
button.
RIGHT CLICK BUTTON
Used as a PC mouse in
Wireless Mouse Operation.
(P43)
P-TIMER BUTTON
Used to operate P-TIMER
function. (P24)
LASER POINTER FUNCTION
This Remote Control Unit emits a laser beam as laser pointer function from Laser Light Window. When LASER button is
pressed, laser light goes on. And when LASER button is being pressed for more than 1 minute or LASER button is released,
light goes off. LASER POINTER INDICATOR lights RED and Laser is emitted with RED light to indicate laser beam is being
emitted.
Laser emitted is a class II laser; therefore, do not look into Laser Light Window or shine laser beam on yourself or other
people. Three marks bellow are caution labels for laser beam.
CAUTION : Use of controls, adjustments or performance of procedures other than those specified herein may result
hazardous radiation exposure.
These caution labels are put on remote control.
LASER POINTER INDICATOR
Laser Light Window
18
Downloaded From projector-manual.com Christie Manuals
BEFORE OPERATION
Operating Range
ON-OFF
ZOOM BUTTON
Used to adjust zoom.
(P23)
ZOOM
FOCUS VOLUME
LOCK
VOLUME BUTTON
Used to adjust volume.
(P25)
Point Remote Control Unit toward
projector (Receiver Window)
whenever pressing any button.
Maximum operating range for
Remote Control Unit is about 16.4’
(5m) and 60° in front and rear of a
projector.
MUTE D.ZOOM INPUT 1/2
FOCUS BUTTON
Used to adjust focus.
(P23)
D.ZOOM BUTTON
MENU
INPUT 3/4
Used to select DIGITAL
ZOOM +/– mode and
resize image. (P34)
60°
MUTE BUTTON
16.4’
(5 m)
LENS SHIFT BUTTON
Used to mute sound.(P25)
Used to select LENS
SHIFT function. (P23)
LASER
LENS SHIFT
NO SHOW BUTTON
FREEZE BUTTON
Used to turn picture into
black image. (P24)
AUTO PC ADJ. BUTTON
KEYSTONE
NO SHOW
FREEZE
IMAGE
AUTO PC ADJ.
P-TIMER
Use to operate AUTO PC
Adjustment function. (P29)
Used to freeze picture.
(P24)
IMAGE BUTTON
Used to select image
level. (P32, 37)
KEYSTONE BUTTON
Used
to
correct
keystone distortion.
(P23, 40)
WIRED REMOTE JACK
When using as Wired
Remote Control, connect
Remote Control Cable to
this jack.
Battery installation is
required when using as
Wired Remote Control.
16.4’
(5 m)
60°
Remote Control Batteries Installation
1
Remove battery
compartment lid.
Press lid downward and slide it.
2
Slide batteries into
compartment.
3
Replace compartment lid.
Two AA size batteries
For correct polarity (+ and
–), be sure battery
terminals are in contact
with pins in compartment.
To insure safe operation, please observe following precautions :
● Use (2) AA, UM3 or R06 type alkaline batteries.
● Replace two batteries at same time.
● Do not use a new battery with an used battery.
● Avoid contact with water or liquid.
● Do not expose Remote Control Unit to moisture, or heat.
● Do not drop Remote Control Unit.
● If a battery has leaked on Remote Control Unit, carefully wipe case clean and install new batteries.
● Danger of explosion if battery is incorrectly replaced.
● Dispose of used batteries according to the batteries manufacturers instructions and local rules.
Downloaded From projector-manual.com Christie Manuals
19
BEFORE OPERATION
OPERATING ON-SCREEN MENU
HOW TO OPERATE ON-SCREEN MENU
You can control and adjust this projector through ON-SCREEN
MENU. Refer to following pages to operate each adjustment on
ON-SCREEN MENU.
WIRELESS REMOTE CONTROL
POINT BUTTON
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
1 DISPLAY MENU
Press MENU button to display ON-SCREEN MENU.
2 MOVING POINTER
Move pointer (✽ see below) or adjust value of item by pressing
POINT button(s) on Side Control or on Remote Control Unit.
✽ Pointer is a icon on ON-SCREEN MENU to select item. See figures on section "FLOW OF ON-SCREEN MENU OPERATION"
below.
SELECT BUTTON
Used to select item.
SIDE CONTROL
LENS SHIFT
MENU
I
SELECT
3 SELECT ITEM
Select item or set selected function by pressing SELECT button.
I
POINT BUTTONS
Used to move Pointer
UP/ DOWN/ RIGHT/
LEFT.
SELECT BUTTON
Used to select item.
AUTO PC ADJUST
IMAGE
FLOW OF ON-SCREEN MENU OPERATION
Display ON-SCREEN MENU
1
MENU ICON
Press MENU button to display ON-SCREEN MENU (MENU
BAR). A red frame is POINTER.
Select Menu to be adjusted
2
MENU BAR
Move POINTER (red frame) to MENU ICON that you want to
select by pressing POINT RIGHT / LEFT buttons.
POINTER (red frame)
Press POINT DOWN button to
move POINTER.
POINTER
(red frame)
ITEM
Control or adjust item through ON-SCREEN MENU
3
4
Press POINT DOWN button and move POINTER (red frame
or red arrow) to ITEM that you want to adjust, and then press
SELECT button to show ITEM DATA.
SELECT
BUTTON
Adjust ITEM DATA by pressing POINT RIGHT / LEFT
buttons.
Refer to following pages for details of respective
adjustments.
ITEM DATA
Press POINT LEFT/RIGHT
buttons to adjust value or
set function.
20
Downloaded From projector-manual.com Christie Manuals
BEFORE OPERATION
MENU BAR
FOR PC SOURCE
Press MENU BUTTON while connecting to PC input source.
IMAGE SELECT MENU
SCREEN MENU
SETTING MENU
Used to adjust size
of image. [Normal
/ True / Wide /
Digital zoom +/–]
(Refer to P34)
Used to change
settings of projector
or reset Lamp
Replace Counter.
(Refer to P40-42)
GUIDE WINDOW
PC SYSTEM MENU
Shows selected
item of ONSCREEN MENU.
Used to select
computer system.
(Refer to P27, 28)
Used to select
image level among
Standard, Real
and Image 1 ~ 4.
(Refer to P32)
INPUT MENU
PC ADJUST MENU
IMAGE ADJUST MENU
SOUND MENU
Used to select
input source (Input
1, Input 2, Input 3
or Input 4). (Refer
to P26)
Used to adjust
parameters to
match with input
signal format.
(Refer to P29-31)
Used to adjust
computer image.
[Contrast/Brightness
/Color Temp.
/White Balance (R/G/B)
/Sharpness/Gamma
/Noise Reduction
/Progressive]
(Refer to P33)
Used to adjust
sound [volume,
Bass or Treble],
to select Built-in
SP On-Off and
Sound Mute.
(Refer to P25)
FOR VIDEO SOURCE
Press MENU BUTTON while connecting to VIDEO input source.
INPUT MENU
IMAGE SELECT MENU
Used to select
input source (Input
1, Input 2, Input 3
or Input 4). (Refer
to P35)
Used to select image
level among
Standard, Cinema
and Image 1 ~ 4.
(Refer to P37)
Same function as
Menu for PC source.
SCREEN MENU
Used to set size of
image to Normal
or Wide.
(Refer to P39)
AV SYSTEM MENU
IMAGE ADJUST MENU
Used to select
system of selected
video source.
(Refer to P36)
Used to adjust picture image.
[Contrast/Brightness/Color
/Tint/Color Temp.
/White balance (R/G/B)
/Sharpness/Gamma
/Noise Reduction/Progressive]
Same function as
Menu for PC source.
(Refer to P38, 39)
Downloaded From projector-manual.com Christie Manuals
21
BASIC OPERATION
TURNING ON / OFF PROJECTOR
TURNING ON PROJECTOR
1
Complete peripheral connections (with Computer, VCR, etc.)
before turning on projector. (Refer to "CONNECTING TO
PROJECTOR" on Pages 12~15 for connecting that equipment.)
LAMP STATUS
INPUT 1
2
3
Connect a projector's AC Power Cord into a wall outlet and turn
MAIN ON / OFF SWITCH to ON. LAMP indicator lights RED,
and READY indicator lights GREEN.
Press POWER ON-OFF button on Side Control or on Remote
Control Unit to ON. LAMP indicator dims, and Cooling Fans start
to operate. Preparation Display appears on a screen and countdown starts. Signal from source appears after 30 seconds.
Current Input position and Lamp status are also displayed on
screen for 5 seconds. (Refer to "LAMP MANAGEMENT" on
page 45.)
1
3
2
4
30
Preparation Display disappears after
30 seconds.
TURNING OFF PROJECTOR
1
Press POWER ON-OFF button on Side Control or on Remote
Control Unit, and a message "Power off?" appears on a screen.
2
Press POWER ON-OFF button again to turn off projector. LAMP
indicator lights bright and READY indicator turns off. After
approximate 90 seconds, READY indicator will light green again
and projector may be turned on by pressing POWER ON-OFF
button.
3
Cooling fans will operate for approximate 2 minutes after projector is turned off. To power down completely, turn MAIN ON/OFF
SWITCH to OFF and disconnect AC Power Cord.
Power off?
Message disappears after 4 seconds.
TO MAINTAIN LIFE OF LAMP, ONCE YOU TURN
PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE
TURNING IT OFF.
When Power Management function is ON, projector detects signal interruption and turns off Projection Lamp automatically.
Refer to “Power Management” on pages 40 and 41.
When WARNING TEMP. indicator flashes red, projector is automatically turned off. Wait at least 5 minutes before turning on
projector again.
When both WARNING TEMP. and READY indicators to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF.
2. Turn a projector on again.
When WARNING TEMP. indicator continues to flash, follow procedures below:
1. Turn MAIN ON / OFF SWITCH to OFF and disconnect AC Power Cord from an AC outlet.
2. Check Air Filters for dust accumulation.
3. Clean Air Filters. (See "AIR FILTER CARE AND CLEANING" section on page 44.)
4. Turn a projector on again.
If WARNING TEMP. indicator should still continue to flash, contact sales dealer where you purchased this projector or
service center.
22
Downloaded From projector-manual.com Christie Manuals
BASIC OPERATION
ADJUSTING SCREEN
ZOOM ADJUSTMENT
1
Press ZOOM ▲/▼ button on Side Control or on Remote Control
Unit. Message “Zoom” is displayed.
2
Press ZOOM ▲ button to make image larger, and press ZOOM
▼ button to make image smaller.
Zoom
Message disappears after 4 seconds.
FOCUS ADJUSTMENT
1
Press FOCUS ▲/▼ button on Side Control or on Remote Control
Unit. Message “Focus” is displayed.
2
Adjust focus of image by pressing FOCUS ▲/▼ button(s) .
Focus
Message disappears after 4 seconds.
LENS SHIFT ADJUSTMENT
1
Press the LENS SHIFT button on Side Control or on the Remote
Control Unit. Message “Lens shift” is displayed.
2
Press POINT UP button to move image up, press POINT DOWN
button to move image down, press POINT LEFT to move image
left and press POINT RIGHT to move image right.
Lens shift
Message disappears after 4 seconds.
KEYSTONE ADJUSTMENT
If a projected picture has keystone distortion, correct image with KEYSTONE adjustment.
1
Press KEYSTONE ▲/▼ button on Remote Control Unit or select
Keystone on SETTING menu. (Refer to page 40.) Keystone
dialog box appears.
2
Correct keystone distortion by pressing KEYSTONE ▲/▼ button
or POINT UP/DOWN button(s). Press KEYSTONE ▲ button or
POINT UP button to reduce upper part of image, and press
KEYSTONE ▼ button or POINT DOWN button to reduce lower
part.
Reduce upper width with KEYSTONE ▲ button or
POINT UP button.
Downloaded From projector-manual.com Christie Manuals
Reduce lower width with KEYSTONE ▼ button or
POINT DOWN button.
23
BASIC OPERATION
PICTURE FREEZE FUNCTION
Press FREEZE button on Remote Control Unit to freeze picture on-screen. To cancel FREEZE function, press FREEZE
button again or press any other button except POINT / SELECT / RIGHT CLICK / LASER button.
NO SHOW FUNCTION
Press NO SHOW button on Remote Control Unit to black out a image.
To restore to normal, press NO SHOW button again or press any
other button except POINT / SELECT / RIGHT CLICK / LASER button.
No show
Message disappears after 4 seconds.
P-TIMER FUNCTION
Press P-TIMER button on Remote Control unit. Timer display “00 : 00”
appears on a screen and timer starts to count time (00 : 00 ~ 59 : 59).
To stop P-TIMER display, press P-TIMER button. And then, press P-TIMER
button again to cancel P-TIMER function.
24
Downloaded From projector-manual.com Christie Manuals
BASIC OPERATION
SOUND ADJUSTMENT
Indicates roughly level of
volume.
DIRECT OPERATION
Volume
Press VOLUME (+/–) button(s) on Side Control or on Remote Control
Unit to adjust volume. Volume dialog box appears on screen for a few
seconds.
(+) button to increase volume, and (–) button for decreasing.
Mute
Press MUTE button on Remote Control Unit to cut off sound. To
restore sound to its previous level, press MUTE button again or press
Volume (+/–) button(s).
Press MUTE button to set
Mute function On or Off.
Display disappears after 4 seconds.
MENU OPERATION
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
SOUND Menu icon.
2
Press POINT DOWN button to move a red frame pointer to item
that you want to select, and then press SELECT button.
Volume
To increase volume, press POINT RIGHT button, and press POINT
LEFT button for decreasing.
Treble
SOUND MENU
SOUND Menu icon
Indicates roughly
level of volume.
On
Press POINT LEFT/RIGHT buttons
to adjust value.
Close SOUND Menu.
To adjust Treble sound, press POINT RIGHT button or POINT LEFT
button.
Bass
To adjust Bass sound, press POINT RIGHT button or POINT LEFT
button.
Built-in SP.
Press POINT LEFT/RIGHT button(s) to switch built-in speaker on and
off.
Mute
Press POINT LEFT/RIGHT button(s) to cut off sound. Dialog box
display is changed to “On” and sound is cut off. To restore sound to
its previous level, press POINT LEFT/RIGHT button(s) again.
Quit
Closes SOUND MENU.
Downloaded From projector-manual.com Christie Manuals
25
COMPUTER INPUT
SELECTING INPUT SOURCE
DIRECT OPERATION
Select INPUT source by pressing INPUT 1/2 and INPUT 3/4
buttons on Side Control or on Remote Control Unit.
INPUT 1/2 button
INPUT 3/4 button
INPUT 1
INPUT 3
INPUT 2
INPUT 4
MENU OPERATION
1
2
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to select Input and press SELECT
button. Another dialog box INPUT SELECT Menu will appear.
INPUT Menu icon
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to INPUT source that you want to select, and then
press SELECT button.
SELECTING COMPUTER SYSTEM
WHEN SELECT INPUT 1 (DVI INPUT TERMINAL )
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move a red arrow pointer to Input
1 and then press SELECT button. Source Select Menu will
appear.
3
Move a pointer to either Digital or Analog and then press
SELECT button.
Digital
When digital signal is connected on DVI terminal, select
Digital.
Analog
When analog signal is connected on DVI terminal, select
Analog.
INPUT MENU
INPUT Menu icon
Move a pointer (red arrow) to
Input 1 and press SELECT
button.
Input 1
Source Select Menu
Move a pointer to Digital or
Analog and press SELECT
button.
WHEN SELECT INPUT 2 (5 BNC INPUT JACKS )
When connecting a computer output [5 BNC Type (Red, Green, Blue,
Horiz. Sync and Vert. Sync.)] from a computer to R/Pr, G/Y, B/Pb, H/HV
and V jacks.
INPUT MENU
INPUT Menu icon
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.
3
26
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to "RGB", and then press SELECT button.
Downloaded From projector-manual.com Christie Manuals
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Input 2
Source Select Menu
Move a pointer to RGB and
press SELECT button.
COMPUTER INPUT
AUTOMATIC MULTI-SCAN SYSTEM
This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA, SXGA or UXGA (refer
to “COMPATIBLE COMPUTER SPECIFICATIONS” on page 28). When selecting Computer, this projector automatically
tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually.)
Note : Projector may display one of following messages.
Auto
––––
When projector can not recognize connected signal as
PC system provided in this projector, Auto PC Adjustment
function operates to adjust projector and message “Auto”
is displayed on SYSTEM Menu icon. (Refer to P29.)
When image is not provided properly, manual adjustment
is required. (Refer to P29 and 30.)
PC SYSTEM MENU
PC SYSTEM Menu icon
Displays system being
selected.
There is no signal input from computer. Make sure
connection of computer and a projector is set correctly.
(Refer to TROUBLESHOOTING on page 48.)
D-VGA, D-SVGA, D-XGA, D-SXGA 1, D-SXGA 2, D-SXGA 3 or D-UXGA
When digital computer signal is received on DVI terminal,
above message is displayed on PC SYSTEM Menu icon.
SELECT COMPUTER SYSTEM MANUALLY
This projector automatically selects PC system among those provided
in this projector and PC system can be also selected manually.
1
2
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to PC
SYSTEM Menu icon.
Press POINT DOWN button to move a red arrow pointer to
system that you want to set, and then press SELECT button.
PC SYSTEM MENU
PC SYSTEM Menu icon
Displays system being selected.
Systems on this dialog box can
be selected.
Custom Mode (1~5) set in PC
ADJUST Menu. (P31)
Downloaded From projector-manual.com Christie Manuals
27
COMPUTER INPUT
COMPATIBLE COMPUTER SPECIFICATIONS
Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less
than 230 MHz of Dot Clock.
ON-SCREEN
DISPLAY
VGA 1
VGA 2
VGA 3
VGA 4
VGA 5
VGA 6
VGA 7
MAC LC13
MAC 13
RGB
RGB
480p
575p
SVGA 1
SVGA 2
SVGA 3
SVGA 4
SVGA 5
SVGA 6
SVGA 7
SVGA 8
SVGA 9
SVGA 10
SVGA 11
MAC 16
XGA 1
XGA 2
XGA 3
XGA 4
XGA 5
XGA 6
XGA 7
XGA 8
XGA 9
XGA 10
XGA 11
XGA 12
RESOLUTION
640 x 480
720 x 400
640 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Progressive)
––––––––
(Progressive)
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
832 x 624
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
(Interlace)
1024 x 768
1024 x 768
1024 x 768
(Interlace)
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
31.47
31.47
31.47
37.86
37.86
37.50
43.269
34.97
35.00
15.734
15.625
31.47
31.25
35.156
37.88
46.875
53.674
48.08
37.90
34.50
38.00
38.60
32.70
38.00
49.72
48.36
68.677
60.023
56.47
60.31
48.50
44.00
63.48
36.00
62.04
61.00
35.522
59.88
70.09
70.09
74.38
72.81
75.00
85.00
66.60
66.67
30
25
59.88
50
56.25
60.32
75.00
85.06
72.19
61.03
55.38
60.51
60.31
51.09
60.51
74.55
60.00
84.997
75.03
70.07
74.92
60.02
54.58
79.35
43.59
77.07
75.70
43.48
XGA 13
XGA 14
XGA15
MAC 19
MAC 21
SXGA 1
SXGA 2
SXGA 3
SXGA 4
SXGA 5
SXGA 6
SXGA 7
SXGA 8
SXGA 9
SXGA 10
SXGA 11
SXGA 12
SXGA 13
SXGA 14
SXGA 15
SXGA 16
SXGA 17
SXGA 18
SXGA 19
SXGA 20
SXGA 21
MAC
MAC
UXGA 1
UXGA 2
UXGA 3
UXGA 4
720p
1035i
1080i60
1080i50
RESOLUTION
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1152 x 870
1152 x 864
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 1024
1280 x 960
1152 x 900
1152 x 900
1280 x 1024
(Interlace)
1280 x 1024
(Interlace)
1280 x 1024
1280 x 1024
1152 x 900
1280 x 1024
(Interlace)
1280 x 1024
1280 x 1024
1400 x 1050
1280 x 960
1280 x 1024
1600 x 1200
1600 x 1200
1600 x 1200
1600 x 1200
––––––––
(Progressive)
––––––––
(Interlace)
––––––––
(Interlace)
––––––––
(Interlace)
H-Freq.
(kHz)
V-Freq.
(Hz)
46.90
47.00
58.03
60.24
68.68
64.20
62.50
63.90
63.34
63.74
71.69
81.13
63.98
79.976
60.00
61.20
71.40
50.00
50.00
63.37
76.97
61.85
46.43
63.79
91.146
63.93
75.00
80.00
75.00
81.25
87.50
93.750
45.00
33.75
33.75
31.25
58.20
58.30
72.0
75.08
75.06
70.40
58.60
60.00
59.98
60.01
67.19
76.107
60.02
75.025
60.00
65.20
75.60
43.00
47.00
60.01
72.00
66.00
43.35
60.18
85.024
60.00
75.08
75.08
60.00
65.00
70.00
75.00
60.00
30.00
30.00
25.00
When a input signal is digital from DVI terminal, refer to chart below.
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
ON-SCREEN
DISPLAY
RESOLUTION
H-Freq.
(kHz)
V-Freq.
(Hz)
D-VGA
D-SVGA
D-XGA
D-SXGA 1
640 x 480
800 x 600
1024 x 768
1280 x 1024
31.469
37.879
48.363
63.981
59.940
60.317
60.004
60.020
D-SXGA 2
D-SXGA 3
D-UXGA
1280 x 1024
1280 x 1024
1600 x 1200
60.276
31.65
75.00
58.069
29.8
60.00
NOTE : Specifications are subject to change without notice.
28
Downloaded From projector-manual.com Christie Manuals
COMPUTER INPUT
PC ADJUSTMENT
AUTO PC ADJUSTMENT
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your
computer. Auto PC Adjustment function can be operated as follows.
Auto PC Adj.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
2
Press POINT DOWN button to move a red frame pointer to
AUTO PC Adj. icon and then press SELECT button twice.
This Auto PC Adjustment can be also executed by pressing
AUTO PC ADJ. button on Side Control or on Remote Control
Unit.
PC ADJUST MENU
PC ADJUST Menu icon
Move a red frame pointer to AUTO PC
Adj. icon and press SELECT button.
Store adjustment parameters.
Adjustment parameters from Auto PC Adjustment can be memorized
in this projector. Once parameters are memorized, setting can be
done just by selecting Mode in PC SYSTEM Menu (P26). Refer to
step 3 of MANUAL PC ADJUSTMENT section (P30).
NOTE
● Fine sync, Total dots and Picture Position of some computers can
not be fully adjusted with this Auto PC Adjustment function. When
image is not provided properly through this function, manual
adjustments are required. (Refer to page 30, 31.)
● Auto PC Adjustment function can not be operated in Digital Signal
input on DVI terminal and “RGB”, “480p”, “575p”, “720p (HDTV)”,
“1035i (HDTV)”, “1080i50 (HDTV)” or “1080i60 (HDTV)” is selected
on PC SYSTEM Menu (P27).
Downloaded From projector-manual.com Christie Manuals
29
COMPUTER INPUT
MANUAL PC ADJUSTMENT
This projector can automatically tune to display signals from most personal computers currently distributed. However, some
computers employ special signal formats which are different from standard ones and may not be tuned by Multi-Scan system
of this projector. If this happens, projector can not reproduce a proper image and image may be recognized as a flickering
picture, a non-synchronized picture, a non-centered picture or a skewed picture.
This projector has a Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This
enables you to recall setting for a specific computer whenever you use it.
Note : This PC ADJUST Menu can not be operated in Digital Signal input on DVI terminal is selected on PC SYSTEM
MENU (P27).
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to PC
ADJUST Menu icon.
2
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button.
Adjustment dialog box will appear. Press POINT LEFT/RIGHT
button to adjust value.
Fine sync
PC ADJUST MENU
PC ADJUST Menu icon
Move a red frame icon to item and press
SELECT button.
Adjusts an image as necessary to eliminate flicker from display.
Press POINT LEFT/RIGHT button to adjust value.(From 0 to 31.)
Total dots
Number of total dots in one horizontal period. Press POINT
LEFT/RIGHT button(s) and adjust number to match your PC image.
Selected Mode
Shows status
(Stored / Free) of
selected Mode.
Horizontal
Adjusts horizontal picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Vertical
Adjusts vertical picture position. Press POINT LEFT/RIGHT
button(s) to adjust position.
Press POINT LEFT/RIGHT
button to adjust value.
Press SELECT button at this icon to
adjust “Clamp,” “Display area (H/V)” or
set “Full screen.”
Current mode
Press SELECT button to show information of computer selected.
Clamp
Current mode
Adjusts clamp position. When a image has a dark bar(s), try this
adjustment.
Press SELECT button at
Current mode icon to show
information of computer
connected.
30
Downloaded From projector-manual.com Christie Manuals
COMPUTER INPUT
Display area
Selects area displayed with this projector. Select resolution at
Display area dialog box.
Press SELECT button at
Display area icon and Display
area dialog box appears.
Display area H
Adjustment of horizontal area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Display area
Display area V
Adjustment of vertical area displayed with this projector. Press
POINT LEFT/RIGHT button(s) to decrease/increase value and then
press SELECT button.
Full screen
Press POINT LEFT
/RIGHT button(s) to
adjust value and then
press SELECT button.
Press POINT LEFT/RIGHT button(s) to switch Full screen function to
“On” or “Off.” Set “On” to resize image with 4 x 3 aspect ratio to fit a
screen.
NOTE : Fine sync, Display area, Display area H, Display area V and
Full screen can not be adjusted when “RGB”, “480p”, “575p”,
“720p (HDTV)”, “1035i (HDTV)”, “1080i50 (HDTV)” or
“1080i60 (HDTV)” is selected on PC SYSTEM Menu (P27).
3
To store adjustment data.
This Mode has parameters being stored.
Store
To store adjustment parameters, move a red frame pointer to
Store icon and then press SELECT button. Move a red arrow
pointer to any of Mode 1 to 5 that you want to store and then
press SELECT button.
Mode free
To clear adjustment parameters previously set, move a red
frame pointer to Mode free icon and then SELECT button. Move
a red arrow pointer to Mode that you want to clear and then
press SELECT button.
Vacant Mode
Other icons operates as follows.
Store icon
Shows values of “Total dots,”
“Horizontal,” “Vertical,” “Display
area H,” and “Display area V.”
Reset
Reset all adjust parameters on adjustment dialog box to previous
figure.
To clear adjustment data.
Quit
Closes PC ADJUST MENU.
Close this dialog box.
Mode free icon
Downloaded From projector-manual.com Christie Manuals
31
COMPUTER INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Real, Image 1, Image 2, Image 3
and Image 4 by pressing IMAGE button on Side Control or on Remote
Control Unit.
IMAGE button
Standard
Real
Standard
Normal picture level preset on this projector.
Image 1
Real
Picture level with improved halftone for graphics.
Image 2
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P33).
Image 3
Image 4
IMAGE LEVEL SELECT (MENU)
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
2
Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.
IMAGE SELECT MENU
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Real
Move a red frame icon to level and
press SELECT button.
Picture level with improved halftone for graphics.
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P33).
32
Downloaded From projector-manual.com Christie Manuals
Level being selected.
COMPUTER INPUT
IMAGE LEVEL ADJUSTMENT
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to
IMAGE ADJUST Menu icon.
2
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
IMAGE ADJUST MENU
IMAGE ADJUST
Menu icon
Move a red frame pointer to
item to be selected and then
press SELECT button.
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Selected Image level
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Store icon
Press SELECT button at this icon to
store adjustment.
Sharpness
Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Noise reduction
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
Image Level Menu
Move a red frame pointer to any
of Image 1 to 4 where you want
to set and then press SELECT
button.
Progressive
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on.
3
Store
To store manually preset image, move a red frame pointer to
Store icon and press SELECT button. Image Level Menu will
appear. Move a red frame pointer to Image 1 to 4 where you
want to set and then press SELECT button.
Other icons operates as follows.
Reset
Reset all adjustment to previous figure.
Quit
Closes IMAGE MENU.
Downloaded From projector-manual.com Christie Manuals
NOTE :
● Noise reduction can be operated when “RGB”,
“480p”, “575p”, “720p (HDTV)”, “1035i (HDTV)”,
“1080i50 (HDTV)” or “1080i60 (HDTV)” is
selected on PC SYSTEM MENU (P27) only.
● Progressive can be operated when “RGB”,
“1035i (HDTV)”, “1080i50 (HDTV)” or “1080i60
(HDTV)” is selected on PC SYSTEM MENU
(P27) only.
33
COMPUTER INPUT
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
2
Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
SCREEN MENU
SCREEN Menu icon
Move a red frame to function and press
SELECT button.
Normal
Provides image to fit screen size.
True
Provides image in its original size.
Wide
Provides image to fit wide video aspect ratio (16 : 9) by expanding
image width uniformly. This function can be used for providing a
squeezed video signal at 16 : 9.
Digital zoom +
When Digital zoom + is selected, ON-SCREEN MENU disappears
and message “D. Zoom +” is displayed. Press SELECT button to
expand image size. And press POINT UP/DOWN/LEFT/RIGHT
button(s) to pan image. Panning function can work only when image
is larger than screen size.
A projected image can be also expanded by pressing D.ZOOM ▲
button on Remote Control Unit.
Digital Zoom –
When Digital zoom – is selected, ON-SCREEN MENU disappears
and message “D. Zoom –” is displayed. Press SELECT button to
compress image size.
A projected image can be also compressed by pressing D.ZOOM ▼
button on Remote Control Unit.
To cancel Digital Zoom +/– mode, press any button except D.ZOOM
▲/▼, SELECT, POINT and AUTO PC ADJ. buttons.
34
Downloaded From projector-manual.com Christie Manuals
NOTE
● Picture screen adjustment cannot be operated
when “720p (HDTV)”, “1035i (HDTV)”, “1080i50
(HDTV)” or “1080i60 (HDTV)” is selected on PC
SYSTEM Menu (P27).
● True and Digital zoom +/– cannot be operated
when “RGB”, “480p” or “575p” is selected on PC
SYSTEM Menu (P27).
● This projector cannot display any resolution higher
than 1600 X 1200. If your computer’s screen
resolution is higher than 1600 X 1200, reset
resolution to lower before connecting projector.
● Image data in other than UXGA (1600 x 1200) is
modified to fit screen size in initial mode.
● Panning function may not operate properly if
computer system prepared on PC ADJUST Menu
is used.
VIDEO INPUT
SELECTING INPUT SOURCE
WHEN SELECT INPUT 2 (5 BNC SLOT )
When connect component video output (Cr, Y, Cb or Pr, Y, Pb) from
video equipment to R/Pr, G/Y and B/Pb jacks.
1
2
INPUT MENU
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
Press POINT DOWN button to move a red arrow pointer to Input
2 and then press SELECT button. Source Select Menu will
appear.
INPUT Menu icon
Move a pointer (red arrow) to
Input 2 and press SELECT
button.
Input 2
Source Select Menu
3
Press POINT DOWN button and a red-arrow icon will appear.
Move arrow to "Y, Pb/Cb, Pr/Cr" and then press SELECT button.
Move a pointer to
Y, Pb/Cb, Pr/Cr and press
SELECT button.
WHEN SELECT INPUT 3 (AV TERMINAL )
When connecting to those equipment, select a type of Video
source in SOURCE SELECT (VIDEO) Menu.
1
INPUT MENU
INPUT Menu icon
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
INPUT Menu icon.
2
Press POINT DOWN button to move a red arrow pointer to Input
3 and then press SELECT button. Source Select Menu will
appear.
3
Move a pointer to source that you want to select and then press
SELECT button.
Video
When video input signal is connected to VIDEO jack,
select Video.
S-Video
When video input signal is connected to S-VIDEO jack,
select S-Video.
Y, C
When video input signal is connected to VIDEO/Y, C
jacks, select Y, C.
Downloaded From projector-manual.com Christie Manuals
Move a pointer (red arrow) to
Input 3 and press SELECT
button.
Input 3
Source Select Menu (VIDEO)
Move a pointer to source and
press SELECT button.
35
VIDEO INPUT
SELECTING VIDEO SYSTEM
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT buttons to move a red frame pointer to AV
SYSTEM Menu icon.
2
Press POINT DOWN button to move a red arrow pointer to
system that you want to select and then press SELECT button.
VIDEO JACK OR S-VIDEO JACK
Auto
Projector automatically detects incoming Video system, and adjusts
itself to optimize its performance.
When Video System is PAL-M or PAL-N, select system manually first.
AV SYSTEM MENU (VIDEO OR S-VIDEO)
AV SYSTEM Menu icon
This box indicates system
being selected.
PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N
If projector can not reproduce proper video image, it is necessary to
select a specific broadcast signal format among PAL, SECAM, NTSC,
NTSC 4.43, PAL-M, and PAL-N.
Move pointer to system
and press SELECT
button.
Y, Pb/Cb, Pr/Cr JACKS
Auto
Projector automatically detects incoming Video signal, and adjusts
itself to optimize its performance.
When Video System is 1035i, 1080i50 or 1080i60, select system
manually first.
COMPONENT VIDEO SIGNAL FORMAT
If projector can not reproduce proper video image, it is necessary to
select a specific component video signal format among 480i, 575i,
480p, 575p, 720p, 1035i , 1080i50 or 1080i60.
AV SYSTEM MENU (COMPONENT VIDEO)
Auto
1080i60
1080i50
1035i
720p
575p
480p
575i
480i
36
Downloaded From projector-manual.com Christie Manuals
AV SYSTEM Menu icon
This box indicates system
being selected.
Move pointer to system
and press SELECT
button.
VIDEO INPUT
PICTURE IMAGE ADJUSTMENT
IMAGE LEVEL SELECT (DIRECT)
Select image level among Standard, Cinema, Image 1, Image 2,
Image 3 and Image 4 by pressing IMAGE button on Side Control or on
Remote Control Unit.
IMAGE button
Standard
Cinema
Standard
Normal picture level preset on this projector.
Image 1
Cinema
Picture level adjusted for picture with fine tone.
Image 2
IMAGE 1~4
User preset picture adjustment in IMAGE ADJUST Menu (P39).
Image 3
Image 4
IMAGE LEVEL SELECT (MENU)
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button to move a red frame pointer to
IMAGE SELECT Menu icon.
2
Press POINT DOWN button to move a red frame pointer to level
that you want to set and then press SELECT button.
IMAGE SELECT MENU
IMAGE SELECT
Menu icon
Standard
Normal picture level preset on this projector.
Cinema
Move a red frame pointer to level
and press SELECT button.
Picture level adjusted for picture with fine tone.
IMAGE 1~4
Level being selected.
User preset picture adjustment in IMAGE ADJUST Menu (P39).
Downloaded From projector-manual.com Christie Manuals
37
VIDEO INPUT
IMAGE LEVEL ADJUSTMENT
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
IMAGE ADJUST Menu icon.
2
Press POINT DOWN button to move a red frame pointer to item
that you want to adjust and then press SELECT button. Level of
each item is displayed. Adjust each level by pressing POINT
LEFT/RIGHT button(s).
IMAGE ADJUST MENU
Move a red frame pointer to
item to be selected and then
press SELECT button.
IMAGE ADJUST
Menu icon
Contrast
Press POINT LEFT button to decrease contrast, and POINT RIGHT
button to increase contrast. (From 0 to 63.)
Brightness
Press POINT LEFT button to adjust image darker, and POINT
RIGHT button to adjust brighter. (From 0 to 63.)
Color
Press POINT LEFT button to lighten color, and POINT RIGHT button
to deeper color. (From 0 to 63.)
Tint
Press POINT LEFT button or POINT RIGHT button to obtain proper
color. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
Press SELECT button at this icon to
display other items.
Color temp.
Press either POINT LEFT button or POINT RIGHT button to Color
temp. level that you want to select. (XLow, Low, Mid or High)
White balance (Red)
Press SELECT button at this icon to
display previous items.
Press POINT LEFT button to lighten red tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
White balance (Green)
Press POINT LEFT button to lighten green tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Press POINT LEFT/RIGHT buttons
to adjust value.
White balance (Blue)
Press POINT LEFT button to lighten blue tone and POINT RIGHT
button to deeper tone. (From 0 to 63.)
Sharpness
Press POINT LEFT button to soften image, and POINT RIGHT
button to sharpen image. (From 0 to 15.)
Gamma
Press either POINT LEFT button or POINT RIGHT button to obtain
better balance of contrast. (From 0 to 15.)
Noise reduction
Press POINT LEFT/RIGHT button(s) to change noise reduction
mode. Dialog box display is changed to “On” to reduce noise (rough
parts) of image. Press POINT LEFT/RIGHT button(s) again, to
change noise reduction mode to off.
Progressive scan
Press POINT LEFT/RIGHT button(s) to change progressive scan
mode. Dialog box display is changed to “Off” and progressive scan
mode to off. Press POINT LEFT/RIGHT button(s) again, progressive
scan mode to on.
38
Downloaded From projector-manual.com Christie Manuals
Press SELECT button at this icon to
store value.
NOTE :
Tint can not be adjusted when video system is
PAL, SECAM, PAL-M or PAL-N.
Progressive can not be operated when “480p”,
“575p” or “720p” is selected on AV SYSTEM
MENU (P36).
VIDEO INPUT
3
Store
To store adjustment data, move a red frame pointer to Store icon
and press SELECT button. Image Level Menu will appear.
Move a red frame pointer to Image Level 1 to 4 and then press
SELECT button.
Image Level Menu
Move a red frame pointer to
image icon to be set and
then press SELECT button.
Other icons operates as follows.
Reset
Reset all adjustment to previous figure.
Quit
Store icon
Closes IMAGE MENU.
PICTURE SCREEN ADJUSTMENT
This projector has a picture screen resize function, which enables you to display desirable image size.
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red frame pointer to
SCREEN Menu icon.
2
Press POINT DOWN button and move a red frame pointer to
function that you want to select and then press SELECT button.
Normal
SCREEN MENU
SCREEN Menu icon
Move a red frame to function and press
SELECT button.
Provides image at a normal video aspect ratio of 4 : 3.
Wide
Provides image at a wide screen ratio of 16 : 9.
Downloaded From projector-manual.com Christie Manuals
NOTE : SCREEN Menu can not be operated when
“720p”, “1035i”, “1080i50” or “1080i60” is
selected on AV SYSTEM Menu (P36).
39
SETTING
SETTING MENU
1
Press MENU button and ON-SCREEN MENU will appear. Press
POINT LEFT/RIGHT button(s) to move a red-frame pointer to
SETTING icon.
2
Press POINT DOWN button to move a red-frame pointer to item
that you want to set and then press SELECT button. Setting
dialog box appears.
SETTING MENU
Set a red frame
pointer to item and
press SELECT
button.
SETTING Menu icon
Language
Language used in ON-SCREEN MENU is selectable from among
English, German, French, Italian, Spanish, Portuguese, Dutch,
Swedish, Russian, Chinese, Korean and Japanese.
Keystone
When image is distorted vertically, select Keystone. ON-SCREEN
MENU disappears and Keystone dialog box is displayed.
Correct keystone distortion by pressing POINT UP/DOWN button(s).
Refer to KEYSTONE ADJUSTMENT on page 23.
When pressing SELECT
button at Language,
Language Menu appears.
Blue back
When this function is “On,” this projector will produce a blue image
instead of video noise on screen when any input source is unplugged
or turned off.
Display
This function decides whether to display On-Screen Displays.
On ··· shows all On-Screen Displays.
Off ···· sets On-Screen Displays disappeared except;
● ON-SCREEN MENU
● “Power off?” message
Logo
Move a pointer to item Optional Control
and then press POINT Refer to page 11.
LEFT/RIGHT button(s).
When this function is “On,” projector displays our logo when starting
up.
Ceiling function
Ceiling
When this function is “On,” picture is top/bottom and left/right
reversed. This function is used to project image from a ceiling
mounted projector.
Rear
When this function is “On,” picture is left/right reversed. This function
is used to project image to a rear projection screen.
40
Downloaded From projector-manual.com Christie Manuals
Rear function
Number
SETTING
Power management
This function turns Projection Lamp off when this projector detects
signal interruption and is not used for a certain period in order to
reduce power consumption and maintain Lamp-life. (This projector is
shipped with this function ON.)
Power Management function operates to turn Projection Lamp off
when input signal is interrupted and any button is not pressed over 5
minutes. This function operates as follows;
1. When any input signal is interrupted, “No signal” and counting
down display appears (for 5 minutes).
2. After counting down for 5 minutes, projector lamp and READY
indicator are turned off.
3. When READY indicator flashing, Projection Lamp can be
turned on again (Power Management mode).
In this Power Management mode, Projection Lamp is
automatically turned on when input signal connected or
projector is operated with any button on Side Control or on
Remote Control Unit again.
On start
Time left until Lamp off.
Press SELECT button at this icon to
display other items.
On start
When this function is “On,” projector is automatically turned on just
by switching MAIN ON/OFF SWITCH on.
Press SELECT button at this icon to
display previous items.
Note ; Be sure to turn projector off properly (refer to section
“TURNING OFF PROJECTOR” on P22). If projector is turned
off in wrong steps, On Start function does not operate
properly.
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s).
Lamp Mode
This Projector is equipped with 4 Projection Lamps and a number of using lamps can be switched to 4 lamps or 2 lamps.
Using 2 lamps maintain life of Projection Lamps.
To change over Lamp Mode
1. Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select SETTING and
press SELECT button. Setting dialog box appears.
2. Press POINT DOWN button to move a red frame pointer to “Lamp mode”. Set "4 lamps mode" or "2 lamps mode" by
pressing POINT LEFT/RIGHT button(s). When Lamp Mode is set from "4 lamps mode" to "2 lamps mode" image
becomes little darker. When Lamp Mode is set from "2 lamps mode" to "4 lamps mode" image become brighter
gradually.
NOTE : After changing Lamp Mode, it can not be switched again for 90 seconds.
Remote control
This projector has two different remote control codes; factory-set normal code (Code 1) and secondary code (Code 2). This
switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment
together.
When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”
To change code of Projector;
Set Remote control in SETTING MENU to “Code 2.”
To change code of Remote Control Unit;
Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.
After changing code, make sure Remote Control operates properly.
To return to normal code (Code 1), operate both projector and Remote Control in ways above again.
NOTE : When batteries of Remote Control Unit are replaced or ALL-OFF switch is turned to “ALL-OFF,” remote transmit
code automatically returns to normal code (Code 1).
Downloaded From projector-manual.com Christie Manuals
41
SETTING
USB
This Projector is equipped with USB port for interactive operation
between a projector and computer. Set mode following steps below.
USB
Press SELECT button at this icon to
display previous items.
Wireless Mouse mode
Select "
this projector.
" when controlling a computer with Remote Control of
Projector mode
Select "
" when controlling a projector with computer.
Move a pointer to item and then
press POINT LEFT/RIGHT
button(s).
NOTE: Before you control a projector by computer, install USB driver
(optionally sold parts) and set up computer following instruction in USB driver package. Contact your authorized dealer.
Lamp counter reset
Be sure to reset Lamp Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP
REPLACE indicator stops lighting.
1
Turn projector on, press MENU button and ON-SCREEN
MENU will appear. Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon.
2
Press POINT DOWN button to move a red frame pointer to
“Lamp counter reset” and then press SELECT button.
3
Move arrow to replaced lamp number (Lamp 1, Lamp 2, Lamp 3
or Lamp 4) and then press SELECT button. Message "Lamp
replace counter Reset?" is displayed. Move pointer to [Yes] and
then press SELECT button.
NOTE: Be sure to reset correct lamp number otherwise LAMP
REPLACE indicator continues lighting.
4
1
3
2
4
Move pointer to Lamp counter reset and then
press SELECT button. Move arrow to
replaced lamp number (Lamp 1, Lamp
2, Lamp 3 or Lamp 4) and then press
SELECT button.
Another confirmation dialog box appears and select [Yes] to
reset Lamp Replace Counter.
Do not reset Lamp Replace Counter except after Projection lamp is
replaced.
Quit
Closes SETTING MENU.
Message "Lamp replace counter Reset?" is
displayed. Move pointer to [Yes] and then
press SELECT button.
42
Downloaded From projector-manual.com Christie Manuals
APPENDIX
OPERATING WIRELESS MOUSE
Wireless Remote Control Unit is not only able to operate this projector but also usable as a wireless mouse for most
Personal Computers. POINT buttons and two CLICK buttons are used for wireless mouse operation.
This Wireless Mouse function is available only when PC mouse pointer is displayed on a projected screen. When ONSCREEN MENU or any message / dialog box is displayed on screen instead of PC mouse pointer, this Wireless Mouse
function can not be used.
INSTALLATION
To use Wireless Remote Control Unit as Wireless Mouse for a Personal Computer, installation of mouse driver (not supplied)
is required. Make sure that mouse driver is properly installed in your computer. And make sure that mouse port (or USB
port) of a Personal Computer is activated.
1
Connect mouse port (or USB port) of your computer to Control
Port (or USB connector) of this projector with Control Cable (or
USB cable). (Refer to page 13, 14 for connection.)
2
Turn a projector on first, and then turn on your computer. When
computer is switched on first, Wireless Mouse may not work
properly.
Note : When your computer has no mouse
port, connect Serial Port of your
computer to Control Port of a projector
with Control Cable for Serial Port (not
supplied).
OPERATING WIRELESS MOUSE
When controlling a PC mouse pointer, operate Wireless Mouse with POINT button, SELECT button, and RIGHT CLICK
button on Wireless Remote Control Unit.
POINT button
POINT button (Move pointer)
Used to move PC mouse pointer. Pointer is moved corresponding
with direction you are pressing.
SELECT (LEFT CLICK) button
This button has same function as left button in a PC mouse.
RIGHT CLICK button
This button has same function as right button in a PC mouse. This
button is not available for controlling this projector.
SELECT button
(left button of mouse)
RIGHT CLICK button
(right button of mouse)
MAINTENANCE
WARNING TEMP. INDICATOR
WARNING TEMP. Indicator flashes red and projector is automatically turned off when an internal temperature of a projector
exceeds normal temperature. Wait at least 5 minutes before turning on projector again.
When WARNING TEMP. Indicator continues to flash, check items listed below.
1
2
3
Ventilation Slots of a projector may be blocked. In such an event, reposition a projector so that Ventilation Slots are
not obstructed.
Air Filter may be clogged with dust particles. Clean Air Filter by following section AIR FILTER CARE AND CLEANING
on next page.
If WARNING TEMP. Indicator remains on after performing above checks, Cooling Fans or Internal Circuits may be
malfunctioning. Contact service personnel from an authorized dealer or a service station.
Downloaded From projector-manual.com Christie Manuals
43
APPENDIX
AIR FILTER CARE AND CLEANING
Air Filter prevents dust from accumulating on surface of Projection Lens and Projection Mirror. Should Air Filter
become clogged with dust particles, it will reduce Cooling Fans' effectiveness and may result in internal heat
build up and adversely affect life of a projector.
Clean Air Filter following steps below:
1
Turn power off, and disconnect AC power cord from AC outlet.
2
Pull out air filter from a projector.
3
Pulling up center frame of air filter top, separate air filter top and
sheet from air filter base.
4
Clean each parts with brush or wash out dust and particles. Be
sure to dry them out.
5
Assemble sheet and air filter and replace air filter to a projector.
AIR FILTER
AIR FILTER
TOP
CAUTION
Do not operate a projector with Air Filter
removed. Dust may accumulate on LCD
Panel and Mirror degrading picture quality.
Do not put small parts into Air Intake Vents.
It may result in malfunction of a projector.
AIR FILTER
BASE
SHEET
RECOMMENDATION
We recommend avoiding dusty/smoky environments when operating a projector. Usage in these
environments may cause poor image quality.
When using under dusty or smoky conditions, dust may accumulate on liquid crystal panel, lens, or optical elements inside it.
This condition may degrade quality of projected image.
When above symptoms are noticed, contact your authorized dealer or service station for proper cleaning.
CLEANING PROJECTION LENS
Follow these steps to clean projection lens:
44
1
Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents or other harsh chemicals might scratch lens.
2
3
Lightly wipe cleaning cloth over lens.
When a projector is not in use, replace lens cover.
Downloaded From projector-manual.com Christie Manuals
APPENDIX
LAMP MANAGEMENT
This Projector is equipped with 4 Projection Lamps to ensure brighter image and those lamps are controlled by Lamp
Management Function. Lamp Management Function detects status of all lamps and shows status on screen or on LAMP
REPLACE indicator. This function also automatically controls Lamp Mode when any of lamps is out for end of life or
malfunctions.
LAMP STATUS
INPUT 1
1
3
2
4
30
LAMP REPLACE
INDICATOR
Lamp Replace Indicator
This LAMP REPLACE indicator lights yellow when any of Projection Lamps is nearing its end, and flashes when any of them
becomes out. Check number of lamp on Lamp Status Display and replace lamp.
Lamp Status Display
Lamp Status Display appears on screen when power switch is on or changed input position (input 1, input 2, Input 3 or input 4).
This shows status of each lamp as; ON, OFF, NEAR END, or OUT. Refer to following for each status.
1
2
3
4
LAMP STATUS
DISPLAY
Yellow Lamp
Projection Lamp lights normally.
Dim Lamp
Projection Lamp is turned off.
Red Lamp
Projection Lamp is nearing its end. When image becomes
darker or color becomes unnatural, replace lamp. (LAMP
REPLACE indicator lights yellow.)
X Mark on Lamp
(LAMP REPLACE indicator flashes yellow.)
Projection lamp is defective or fails to be turned on. Restart
a projector on, and make sure lamp is on. If this mark still
appears, replace lamp corresponding with number marked
X.
Lamp Mode Changeover
Lamp Management Function automatically changes combination of lighting lamp (Lamp Mode) by detecting status of lamp.
When any of 4 lamps becomes out, Lamp Mode is changed over from 4 lamps to 2 lamps. And when any of 2 lamps are out,
a projector operates with 1 lamp. Lamp Mode can be switched to 4 lamps or 2 lamps manually. Refer to SETTING section
on page 40, 41.
1
3
1
3
1
3
2
4
2
4
2
4
4 LAMP MODE
Downloaded From projector-manual.com Christie Manuals
2 LAMP MODE
(Example)
1 LAMP MODE
(Example)
45
APPENDIX
LAMP REPLACEMENT
When the life of the Projection Lamp of this projector draws to an end,
the LAMP REPLACE indicator lights yellow. If this indicator lights
yellow, replace the projection lamp with a new one promptly.
FRONT INDICATORS
REAR INDICATORS
LAMP
READY
WARNI
TEMP.NG
LAMP
LA P
REPLM
ACE
READY
LAMP
REPLACE
WARNING
TEMP.
LAMP REPLACE
INDICATOR
CAUTION
Allow a projector to cool, for at least 45 minutes before
you open Lamp Cover. The inside of a projector can
become very hot.
For continued safety, replace with a lamp assembly of
the same type.
Do not drop a lamp assembly or touch a glass bulb! The
glass can shatter and may cause injury.
Follow these steps to replace lamp assembly.
BUTTON
1
Check number of lamp to be replaced on Lamp Status Display.
2
Turn off a projector and disconnect AC Power Cord. Allow a
projector to cool down for at least 45 minutes.
3
Remove two screws on Lamp Cover and press button to open
Lamp Cover. (See right figure.)
4
Loosen two screws and pull out Lamp Assembly to be replaced
by grasping handle.
5
Replace Lamp Assembly with a new one and tighten two screws.
Make sure Lamp is set properly
6
Replace Lamp Cover and tighten two screws.
7
Connect AC Power Cord to a projector and turn a projector on.
8
Reset Lamp Replacement Counter. (Refer to section "Lamp
Counter Reset" on page 42.)
LAMP
COVER
SCREWS
SCREWS
LAMP 3
NOTE : Do not reset LAMP REPLACEMENT COUNTER when
lamp is not replaced.
LAMP 1
LAMP 4
LAMP 2
Make sure which number of lamp needs to be
replaced on Lamp Status Display.
Figure shows case of replacing LAMP 2.
CAUTION : DO NOT OPERATE A PROJECTOR WHILE ANY OF LAMPS IS REMOVED. IT MAY
RESULT IN MALFUNCTIONS, FIRE HAZARD, OR OTHER ACCIDENTS.
NOTES ON LAMP REPLACEMENT
To maintain quality of picture (better balance of color and brightness in entire screen), we recommend replacing
all 4 lamps at a time.
46
Downloaded From projector-manual.com Christie Manuals
APPENDIX
ORDER REPLACEMENT LAMP
Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the
following information to the dealer.
●
Model No. of your projector
● Replacement Lamp Type No.
:
:
38-VIV403-01
03-000709-01P
(Service Parts No. 610 300 0862)
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly. Improper
handling may result in accidents, injury, or create a fire hazard.
● Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a
shorter period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE INDICATOR
lights up, replace the lamp with a new one IMMEDIATELY after the projector has cooled down.
( Follow carefully the instructions in the LAMP REPLACEMENT section of this manual. ) Continuous
use of the lamp with the LAMP REPLACE INDICATOR lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out
from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one
should check the inside of the projector except those who are authorized trained technicians and who are
familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who
are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken
glass.
Downloaded From projector-manual.com Christie Manuals
47
APPENDIX
TROUBLESHOOTING
Before calling your dealer or service center for assistance, check matters below once again.
1. Make sure you have connected a projector to your computer or video equipment as described in section "CONNECTING
PROJECTOR" on pages 12 ~ 15.
2. Check cable connection. Verify that all computer, video and power cord are properly connected.
3. Verify that all power is switched on.
4. If a projector still does not produce an image, re-start your computer.
5. If an image still does not appear, unplug a projector from your computer and check your computer monitor's
display.Problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be
sure to turn a computer and monitor off before you power up a projector. Power equipment back on in order of : Projector
and computer.)
6. If problem still exists, check following chart.
Problem:
No power.
Try these Solutions
● Plug a projector into your AC outlet.
● Turn MAIN ON/OFF switch to ON.
● Press POWER ON/OFF switch to ON.
● Make sure READY Indicator lights.
● Wait 90 seconds after a projector is turned OFF when turning a projector back on.
NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as
follows:
1. LAMP indicator lights bright and READY indicator turns off.
2. After 90 seconds, READY indicator lights green again and a projector may be
turned on by pressing Power ON-OFF button.
● Check WARNING TEMP. and READY indicator. If both WARNING TEMP. and READY
indicator flashes, a projector can not be turned on.
(See "TURNING ON/OFF PROJECTOR" section on page 22.)
● Check Projection Lamp. (Refer to page 46.)
Image is out of
focus.
● Adjust focus of a projector.
● Check Projection Lens to see if it needs cleaning.
NOTE : Moving a projector from a cool temperature location to a warm temperature location
may result in moisture condensation on Projection Lens. In such an event, leave a
projector OFF and wait until condensation disappears.
Picture is Left/Right
reversed.
● Check Ceiling / Rear feature. (See “SETTING” section on page 40.)
Picture is
Top/Bottom
reversed.
● Check Ceiling feature. (See “SETTING” section on page 40.)
Some displays are
not seen during
Operation.
● Check Display feature.(See “SETTING” section on page 40.)
No image.
● Check connection between your computer or video equipment and a projector.
● When turning a projector on, it takes about 30 seconds to display an image.
● Check system that you select is corresponding with your computer or video equipment.
● Make sure temperature is not out of Operating Temperature (5°C ~ 35°C).
No sound.
48
● Check audio cable connection from audio input source.
● Adjust audio source.
● Press VOLUME (+) button.
● Press MUTE button.
Downloaded From projector-manual.com Christie Manuals
APPENDIX
Problem:
Try these Solutions
Remote Control Unit
does not work.
●
●
●
●
Wireless Mouse
function does not
work.
● Check cable connection between a projector and your computer.
● Check mouse setting on your computer.
● Turn a projector on before turning on a computer.
Check batteries.
Check ALL-OFF switch on Remote Control Unit is set to “ON.”.
Make sure nothing is between Infrared Remote Receiver and Remote Control Unit.
Make sure you are not too far from a projector when using Remote Control Unit.
Maximum operating range is 16.4’ (5m).
● Check transmitted signal mode from Remote Control Unit.
(See “SETTING” section on page 40.)
SERVICE
WARNING: High voltages are used to operate this projector. Do not attempt to open cabinet.
You can often correct operating problems yourself. If a projector fails to work properly, see "TROUBLESHOOTING" section on page 48, 49. To correct failure, try "Solutions".
If after following all operating instructions, you find that service is necessary, contact Christie Service Station or
store where you purchased unit.
Give model number and explain difficulty. We will advise you how to obtain service.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety
standards against risk of fire, casualty and electrical hazards.
The CE Mark is a Directive conformity mark of the European Community (EC).
Downloaded From projector-manual.com Christie Manuals
49
APPENDIX
TECHNICAL SPECIFICATIONS
Projector Type
Dimensions (W x H x D)
Net Weight
LCD Panel System
Panel Resolution
Number of Pixels
Color System
High Definition TV Signal
Motorized Lens Shift
Scanning Frequency
Horizontal Resolution
Projection Lamp
Input 1 Jacks
Multi-media Projector
22.9" x 10" x 30.9" (581 mm x 252 mm x 783 mm)
81.7 lbs (37 kg)
1.8" TFT Active Matrix type, 3 panels
1600 x 1200 dots
5,760,000 (1600 x 1200 x 3 panels)
PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N
480i, 480p, 575i, 575p, 720p, 1035i, 1080i-50 and 1080i-60
Up, Down, Left and Right
H-sync. 15 ~ 120 KHz, V-sync. 50 ~ 120 Hz
1100 TV lines
250 watt type x 4
DVI-I Terminal (Digital/Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)
Input 2 Jacks
BNC Type x 5 (R/Pr, G/Y, B/Pb, H/HV and V), RCA Type (Audio R and L)
and DIN 8-pin (Control port)
Input 3 Jacks
BNC Type x 2 (VIDEO/Y, C), RCA Type (Audio R and L)
and DIN 4-pin (S-Video)
Input 4 Jacks
HDB 15-pin Terminal (Analog), RCA Type (Audio R and L)
and DIN 8-pin (Control port)
Other Jacks
Serial port in (DB 9), Serial port out (DB 9), USB port,
Audio Monitor out (RCA Type R and L) and Wired Remote Jack
Built-in Speakers
Feet Adjustment
Voltage and
Power Consumption
Operating Temperature
Storage Temperature
Remote Control Transmitter
Accessories
INT. SP. Stereo (R and L), 3 watt RMS (T.H.D. 10%)
0˚ to 5.7˚
AC 120 V
(12 A Max. Ampere), 50 / 60 Hz (The U.S.A and Canada)
AC 200 ~ 240 V (7.5 A Max. Ampere), 50 / 60 Hz (Continental Europe)
41 ˚F ~ 95 ˚F (5 ˚C ~ 35 ˚C)
14 ˚F ~ 140 ˚F (-10 ˚C ~ 60 ˚C)
Power Source
Operating Range
Dimensions
Net Weight
Laser Pointer
:
:
:
:
:
AA, UM3 or R06 Type x 2
16.4’ (5m) / ±30˚
2.2” x 1.3” x 7.6” (55mm x 34mm x 192mm)
0.36 lbs (165 g) (including batteries)
Class II Laser (Max. Output : 1mW / Wave length : 650±20nm)
User’s Manual
AC Power Cord
Wireless/Wired Remote Control Transmitter and Batteries
Remote Control Cable
VGA Cable and DVI Cable
MAC/VGA Adapter and DVI/VGA Adapter
3 Types Control Cable (For PS/2, Serial and ADB port)
6 Types Light-Block Sheet (For option lens)
Lens Attachment (For option lens)
Protective Dust Cover
● Specifications are subject to change without notice.
● LCD panels are manufactured to the highest possible standards. At least 99.99% of the pixels are effective,
however a tiny fraction of the pixels (0.01% or less) may be ineffective by the characteristics of the LCD
panels.
50
Downloaded From projector-manual.com Christie Manuals
APPENDIX
CONFIGURATIONS OF TERMINALS
DVI-I TERMINAL (DIGITAL/ANALOG)
This terminal accepts only Digital (TMDS) or Analog (RGB) output signal. Connect display output terminal of computer to
this terminal with DVI cable (supplied).
Pin Configuration
C1 C2
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
C3 C4
C5
C1
C2
C3
C4
C5
Analog Red Input
Analog Green Input
Analog Blue Input
Analog Horiz. sync
Analog Ground (R/G/B)
1
2
3
4
5
6
7
8
T.M.D.S. Data2–
T.M.D.S. Data2+
T.M.D.S. Data2 Shield
No Connect
No Connect
DDC Clock
DDC Data
Analog Vert. sync
9
10
11
12
13
14
15
16
T.M.D.S. Data1–
T.M.D.S. Data1+
T.M.D.S. Data1 Shield
No Connect
No Connect
+5V Power
Ground (for +5V)
Hot Plug Detect
17
18
19
20
21
22
23
24
T.M.D.S. Data0–
T.M.D.S. Data0+
T.M.D.S. Data0 Shield
No Connect
No Connect
T.M.D.S. Clock Shield
T.M.D.S. Clock+
T.M.D.S. Clock–
HDB 15-PIN TERMINAL (ANALOG)
Connect display output terminal of computer to this terminal with VGA Cable (supplied).
● When connecting Macintosh computer, use MAC/VGA Adapter (supplied).
● When connecting Analog signal from DVI terminal of computer to this terminal, use DVI/VGA Adapter (supplied).
Pin Configuration
4
5
10
15
14
2
3
9
8
13
1
7
12
1
2
3
4
5
6
7
8
6
11
Red Input
Green Input
Blue Input
Sense 2
Ground (Horiz.sync.)
Ground (Red)
Ground (Green)
Ground (Blue)
9
10
11
12
13
14
15
+5V Power
Ground (Vert.sync.)
Sense 0
DDC Data
Horiz. sync.
Vert. sync.
DDC Clock
CONTROL PORT CONNECTOR
Terminal : Mini DIN 8-PIN
Connect control port (PS/2, Serial or ADB port) on your computer to this terminal with Control Cable (supplied).
Pin Configuration
8
5
7 6
4 3
2 1
1
2
3
4
5
6
7
8
PS/2
----CLK
DATA
GND
--------GND
-----
Downloaded From projector-manual.com Christie Manuals
Serial
RXD
--------GND
RTS
TXD
GND
GND
ADB
----ADB
----GND
------------GND
51
APPENDIX
SERIAL PORT IN/OUT TERMINAL
Pin Configuration
Connect serial port output terminal of computer to this terminal with Serial Cable (not supplied).
1
2
3
4
5
6
7
8
9
5 4 3 2 1
9 8 7 6
----RxD
TxD
----Ground
-----------------
USB PORT TERMINAL
Pin Configuration
Connect USB port output terminal of computer or peripheral equipment to this terminal with USB port Cable (not
supplied).
52
2
1
3
4
1
2
3
4
Downloaded From projector-manual.com Christie Manuals
Vcc
- Data
+ Data
Ground
APPENDIX
Downloaded From projector-manual.com Christie Manuals
53
APPENDIX
54
Downloaded From projector-manual.com Christie Manuals
APPENDIX
Downloaded From projector-manual.com Christie Manuals
55
CHRISTIE DIGITAL SYSTEMS, Inc.
809 Wellington Street North
Kitchener, Ontario
Canada N2G 4Y7
Telephone (519) 744-8005
North America call toll-free
1-800-265-2171 (sales)
Fax (519) 749-3136
CHRISTIE DIGITAL SYSTEMS, Inc.
10550 Camden Drive
Cypress, CA 90630
USA
Telephone (714) 236-8610
Fax (714) 503-3385
Toll Free 1-800-407-7727
Toll Free 1-800-333-3816
CHRISTIE DIGITAL SYSTEMS, Inc.
ViewPoint
200 Ashville Way
Wokingham, Berkshire, U.K.
RG41 2PL
Telephone +44 118 977-8000
Fax +44 118 977-8100
sales-europe@christiedigital.com
Printed in Japan
Downloaded From
projector-manual.com
Christie ManualsMT8K)
Part No.
10-A 610 318 4647 (1AA6P1P4699--
CHRISTIE DIGITAL SYSTEMS, Inc.
Willicher Damm 129
D-41066 Mönchengladbach Germany
Telephone +49 2161 664540
Fax +49 2161 664546
sales-germany@christiedigital.com
CHRISTIE DIGITAL SYSTEMS, Inc.
627A Aljunied Road
#05-02 Biz Tech Centre
Singapore 389842
Telephone 65-877-8737
Fax 65-877-8747
Download PDF

advertising