AOC 2036S User`s guide

AOC MONITOR
USER`S GUIDE
2036S
SAFETY INTRODUCTION…………………………………………………………….2
SETUP…………………………………………………………………………………….7
ADJUSTING…………….…………………………………………………...………….11
DRIVER INSTALLATION GUIDE…………………….….…………………………19
PRODUCT INFORMATION………………………………………………………….26
TROUBLESHOOT……...………………………………………………………….…..28
-1-
SAFETY INTRODUCTION
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the separation between the equipment and receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4.
Consult the dealer or an experienced radio/TV technician for help.
NOTICE :
1.
The changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
2.
Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
3.
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this
equipment. It is theresponsibilities of the user to correct such interference.
WEEE Declaration
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household
waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment
at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal service or the shop where you purchased the product .
HG Declaration
SAFETY: Lamp Disposal
LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO
LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES
ALLIANCE AT WWW.EIAE.ORG.
-2-
Precautions
WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may
result in exposure to shock, electrical hazards, and/or mechanical hazards.
Read and follow these precautions when connecting and using your computer monitor:
PRECAUTIONS
•
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in
a wet basement.
•
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause
serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the
monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow
the kit instructions.
•
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation
of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place
the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat
register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.
•
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of
the type of power supplied to your home, consult your dealer or local power company.
•
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
•
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
•
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
•
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
•
Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous
voltages and other hazards. Please refer all servicing to qualified service personnel.
•
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V AC, Min. 5A.
•
The wall socket shall be installed near the equipment and shall be easily accessible.
•
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license(Only for monitors
with power adapter).
•
Please make sure to clean the cabinet regularly with the provided cloth , you can use soft-cleanser to clean the
stain , instead of severe spray cleanser which will cauterize the monitor cabinet.
•
Dont leak liquid into monitor which will result in the damage of chassis or component. Please unplug before
cleaning ,and do not scratch the screen with hard things.
-3-
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks
are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid
the problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.Some
warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific
presentation of the warning is mandated by regulatory authority.
POWER
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the
type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only
into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an
electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose
of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor
from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured
receptacles marked between 100 - 240V AC, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license (Only for monitors with
power adapter).
INSTALLATION
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and
use mounting accessories recommended by the manufacturer. A product and cart combination should be moved
with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric
shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a fire or damage to the monitor.
-4-
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:
-5-
CLEANING
Clean the cabinet regularly with the cloth provided. You can use soft-detergent to wipe out the stain, instead of
strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough
as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
OTHER
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a
Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
-6-
SETUP
CONTENTS IN BOX
Not all signal cables (Analog, DVI, USB, Audio, and HDMI cables) will be provided for all countries and regions.
Please check with the local dealer or AOC branch office for confirmation.
-7-
SETUP STAND & BASE
Please setup or remove the base following the steps as below.
Setup:
Remove:
ADJUSTING VIEWING ANGLE
•
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's
angle to your own preference.
•
Hold the stand so you will not topple the monitor when you change the monitor's angle.
•
You are able to adjust the monitor's angle from -5° to 20 °
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
-8-
CONNECTING MONITOR
Cable Connections On Back of Monitor and Computer
1. Power
2. Analog (DB-15 VGA cable)
To protect equipment, always turn off the PC and LCD monitor before connecting.
1.
Connect the power cable to the AC port on the back of the monitor.
2.
Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer's D-Sub port.
3.
Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.
-9-
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure.
Follow these steps:
1.
Remove the base.
2.
Follow the manufacturer's instructions to assemble the wall mounting arm.
3.
Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the
back of the monitor.
4.
Insert the 4 screws into the holes and tighten.
5.
Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for
instructions on attaching it to the wall.
Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department
of AOC.
Distance between the wall-mount holes : 100 x 100 mm
Screw specification for wall-mount : M4 x 10
- 10 -
ADJUSTING
Setting the Optimal Resolution
The recommended resolution for this monitor is 1920 by 1080. To setup the monitor to this resolution, follow the steps
below.
For Windows Vista:
1 Click START.
2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization
- 11 -
5 Click Display Settings.
6 Set the resolution SLIDE-BAR to 1920 by 1080.
For Windows XP:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.
- 12 -
4 Click Appearance and Themes.
5 Double click DISPLAY.
6 Click SETTINGS.
7 Set the resolution SLIDE-BAR to 1920 by 1080.
For Windows ME/2000:
1 Click START.
2 Click SETTINGS.
3 Click CONTROL PANEL.
4 Double click DISPLAY.
5 Click SETTINGS.
6 Set the resolution SLIDE-BAR to 1920 by 1080.
- 13 -
HOTKEYS
Power
Press to turn on or turn off the monitor.
4:3 or wide / Up
Press key to change the screen aspect ratio between standard 4:3format or Wide format. When the input
resolution is wide format, the aspect ratio hotkey is disabled. When the main menu or sub-menu is active, the key functions
as to select up or increase value.
Auto / Down
Auto configure hot key: When the OSD is closed, press Auto button to do auto configure.
OSD SETTING
- 14 -
Eco mode ---DCR, Standard, Text, Internet, Game, Movie, Sports
DCR
Standard
- 15 -
TEXT
INTERNET
Game
- 16 -
Movie
Sports
Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as “On”,
Contrast, Brightness, Eco mode and Gamma can not be adjusted.
- 17 -
LED INDICATOR
Status
LED Color
Full Power Mode Blue
Active-off Mode Orange
- 18 -
DRIVER INSTALLATION GUIDE
Windows 2000
Start Windows® 2000
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select 'Monitor'
- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.
- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.
6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.
7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on
'Next' and then click on 'Have disk...'.
8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).
9. Click on the 'Open' button, then click on the 'OK' button.
10. Select your monitor model and click on the 'Next' button.
11. Click on the 'Finish' button then the 'Close' button.
If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.
Windows ME
1. Start Windows® Me
2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.
3. Double click on the 'Display' Icon.
4. Select the 'Settings' tab then click on 'Advanced...'.
5. Select the 'Monitor' button, then click on 'Change...' button.
6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.
7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want'
, then click on 'Next' and then click on 'Have Disk...'.
8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.
9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.
10. Click on 'Finish' button then the 'Close' button.
Windows XP
1. Start Windows® XP
2. Click on the 'Start' button and then click on 'Control Panel'.
- 19 -
3. Select and click on the category ‘Appearance and Themes’
4. Click on the 'Display' Item.
5. Select the 'Settings' tab then click on the 'Advanced' button.
- 20 -
- If the 'Properties' button is active, click on 'Properties' button.
Please follow the steps below.
7. Click on the 'Driver' tab and then click on 'Update Driver...' button.
8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.
- 21 -
9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive
F: (CD-ROM Drive).
11. Click on the 'Open' button, then click the 'OK' button.
12. Select your monitor model and click on the 'Next' button.
- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message
, please click on the 'Continue Anyway' button.
13. Click on the 'Finish' button then the 'Close' button.
14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.
- 22 -
Windows Vista
1. Click "Start " and "Control Panel". Then, double-click on "Appearance and Personalization".
2. Click "Personalization" and then "Display Settings".
3. Click "Advanced Settings...".
4. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration
for your monitor is completed. The monitor can be used as is.
If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue".
- 23 -
5. Click "Update Driver..." in the "Driver" tab.
6. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of
device drivers on my computer".
7. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive
F:\Driver (CD-ROM Drive).
8. Select your monitor model and click on the 'Next' button.
9. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
- 24 -
i-MENU
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen
menus instead of the OSD button on the monitor. Please click here to setup the software. To complete installation,
please follow the installation guide .
- 25 -
PRODUCT INFORMATION
Specifications
LCD Panel
Resolution
Model number
Driving system
Viewable Image
Size
Pixel pitch
Video
Separate Sync.
Display Color
2036S
TFT Color LCD
Dot Clock
140MHz
Horizontal scan
range
Horizontal scan
Size(Maximum)
Vertical scan range
Vertical scan
Size(Maximum)
Optimal preset
resolution
Highest preset
resolution
Plug & Play
Input Connector
Input Video Signal
Power Source
Power
Consumption
Connector Type
Signal Cable Type
Physical
Characteristics Dimensions &
Weight:
Environmental
Temperature:
Humidity:
Altitude:
508.05mm diagonal
0.2768mm(H) x 0.2768mm(V)
R, G, B Analog lnterface & Digital Interface
H/V TTL
16.7M Colors
30 kHz - 80 kHz
442.8mm
55 Hz - 75 Hz
249.075mm
1600 x 900 (60 Hz)
1600 x 900 (60 Hz) )
VESA DDC2B/CI
D-Sub 15pin
Analog: 0.7Vp-p(standard), 75 OHM
100-240VAC, 50/60Hz
Typical < 25W
Standby < 1 W
15-pin Mini D-Sub
Detachable
Height (with base)
378mm
Width
493.8mm
Depth
186mm
Weight (monitor only)
4.2 kg
Weight (with packaging) 5.5kg
Operating
0° to 40°
Non-Operating
-20°to 60°
Operating
10% to 85% (non-condensing)
Non-Operating
5% to 80% (non-condensing)
Operating
0~ 3000m (0~ 10000 ft )
- 26 -
Preset Display Modes
HORIZONTAL
VERTICAL
STAND RESOLUTION
FREQUENCY(kHZ) FREQUENCY(Hz)
640×480 @60Hz DMT
31.469
59.940
VGA
640×480 @67Hz MAC 35.000
66.667
VGA
640×480 @72Hz DMT
37.861
72.809
VGA
640×480 @75Hz DMT
37.500
75.000
Dos-mode
720×400 @70Hz DOS
31.469
70.087
SVGA
800×600 @56Hz DMT
35.156
56.250
SVGA
800×600 @60Hz DMT
37.879
60.317
SVGA
800×600 @72Hz DMT
48.077
72.188
SVGA
800×600 @75Hz DMT
46.875
75.000
SVGA
832×624 @75Hz
49.725
74.550
XGA
1024×768 @60Hz DMT 48.363
60.004
XGA
1024×768 @70Hz DMT 56.476
70.069
XGA
1024×768 @75Hz DMT 60.023
75.029
WSXGA
1600×900 @60Hz DMT 60.000
60.000
VGA
Pin Assignments
Pin Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PLUG & PLAY
15-Pin Side of the Signal Cable
Video-Red
Video-Green
Video-Blue
N.C.
Detect Cable
GND-R
GND-G
GND-B
+5V
Ground
N.C.
DDC-Serial data
H-sync
V-sync
DDC-Serial clock
- 27 -
PLUG & PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC used,
communicate additional information about its display capabilities.
2
The DDC2B is a bi-directional data channel based on the I C protocol. The host can request EDID information
over the DDC2B channel
TROUBLESHOOT
Problem & Question
Power LED Is Not ON
Possible Solutions
•
Make sure the power button is ON and the Power Cord is properly connected
to a grounded power outlet and to the monitor.
Is the power cord connected properly?
Check the power cord connection and power supply.
Is the cable connected correctly?
(Connected using the D-sub cable)
Check the DB-15 cable connection.
(Connected using the DVI cable)
Check the DVI cable connection.
* DVI input is not available on every model.
If the power is on, reboot the computer to see the initial screen (the login
screen), which can be seen.
If the initial screen (the login screen) appears, boot the computer in the
applicable mode (the safe mode for Windows ME/XP/2000) and then change the
frequency of the video card.
(Refer to the Setting the Optimal Resolution)
If the initial screen (the login screen) does not appear, contact the Service
Center or your dealer.
No images on the screen
Can you see "Input Not Supported" on the screen?
You can see this message when the signal from the video card exceeds the
maximum resolution and frequency that the monitor can handle properly.
Adjust the maximum resolution and frequency that the monitor can handle
properly.
Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are
available at : here)
Picture Is Fuzzy & Has
Ghosting Shadowing
Problem
•
Adjust the Contrast and Brightness Controls.
•
Press to auto adjust.
•
Make sure you are not using an extension cable or switch box. We recommend
plugging the monitor directly to the video card output connector on the back .
•
Picture Bounces, Flickers Or
Wave Pattern Appears In
The Picture
Move electrical devices that may cause electrical interference as far away from
the monitor as possible.
•
Use the maximum refresh rate your monitor is capable of at the resolution your
are using.
Monitor Is Stuck In Active
Off-Mode"
•
The Computer Power Switch should be in the ON position.
- 28 -
•
The Computer Video Card should be snugly fitted in its slot.
•
Make sure the monitor's video cable is properly connected to the computer.
•
Inspect the monitor's video cable and make sure no pin is bent.
•
Make sure your computer is operational by hitting the CAPS LOCK key on the
keyboard while observing the CAPS LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
•
Inspect the monitor's video cable and make sure that no pin is damaged.
•
Make sure the monitor's video cable is properly connected to the computer.
Screen image is not
centered or sized properly
•
Adjust H-Position and V-Position or press hot-key (AUTO).
Picture has color defects
(white does not look white)
•
Adjust RGB color or select desired color temperature.
•
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and
FOCUS.
•
Press to auto-adjust.
Horizontal or vertical
disturbances on the screen
- 29 -