Master MH-150V-GFA User`s manual

User’s Manual and
Operating Instructions
Propane
Forced Air Heaters
Model #s: MH-40-GFA, MH-60V-GFA,
MH-125V-GFA, MH-150V-GFA
DE
C
S IGN
D
ER
T IF IE
CERTIFIED
IMPORTANT: Read and understand all of the directions in this manual before assembling,
starting or servicing the heater. Improper use of this heater can cause serious injury.
Table of Contents
Specifications ..........................................................2
Unpacking ................................................................2
Product Features .....................................................2
Propane Supply / Information .................................2
Safety Information.................................................3-4
Operation ..............................................................4-5
Checking for Leaks ..................................................5
Lighting Instructions ................................................5
Storage.....................................................................5
Wiring Diagrams.......................................................6
Replacement Parts ..............................................6-7
Exploded Parts Drawing .......................................7
Troubleshooting Guide .......................... Back Cover
Warranty ................................................. Back Cover
GENERAL HAZARD WARNING: Failure to comply
with the precautions and instructions provided with
this heater, can result in death, serious bodily injury and
property loss or damage from hazards of fire, explosion,
burn, asphyxiation, carbon monoxide poisoning, and/or
electrical shock.
Only persons who can understand and follow the
instructions should use or service this heater.
If you need assistance or heater information such as an
instructions manual, labels, etc, contact the manufacturer.
Not for use in residential living areas or
in non-adequately ventilated enclosed
spaces. Never bring or store a propane cylinder indoors.
DANGER
CONSUMER: Retain this manual for future reference.
Pinnacle Products International, Inc. 668 Stony Hill Road #302 Yardley, PA 19067 USA
Phone: 215-891-8460 Fax: 215-891-8461 Web: www.pinnacleint.com Email: info@pinnacleint.com
221000150-11
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
Specifications
Model #
Rating
BTU/Hr
Fuel
Consumption
Electrical
Input
Manifold
Pressure
Amps
Weight
(Lbs)
Size
(L x W x H)
MH-40-GFA
42,000
1.9 Lbs/Hr
120V, 60 Hz
11” W.C.
0.6
11.2
18” x 7” x 13”
MH-60V-GFA
40,000 1.9 to 2.8 Lbs/Hr
60,000
120V, 60 Hz
11” W.C.
0.6
11.2
18” x 7” x 13”
MH-125V-GFA
95,000 4.4 to 5.8 Lbs/Hr
125,000
120V, 60 Hz
8.3” W.C.
0.8
17.6
25” x 8.6” x 15.5”
MH-150V-GFA
120,0005.5 to 6.9 Lbs/Hr
150,000
120V, 60 Hz
8” W.C.
0.8
17.6
25” x 8.6” x 15.5”
Table 1: Specifications
Specifications subject to change without notice
Unpacking
1. Remove all packing items applied to heater for shipment. Keep
plastic cover caps attached to inlet connector and hose/regulator assembly for storage.
2. Remove all items from carton.
3. Check all items for shipping damage. If heater is damaged,
promptly inform dealer where you purchased the heater.
The Propane (LP) gas pressure regulator
CAUTION and hose assembly supplied with the
heater must be used without alteration.
If the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of
life.
- Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
- An LP cylinder not connected for use shall not be stored
in the vicinity of this or any other appliance.
DANGER
- WHAT TO DO IF THE SMELL OF GAS IS PRESENT:
CAUTION uses air (oxygen) from the area which it is
-
used. Ample combustion and ventilation air must be provided. See VENTILATION on page 5.
-
This is an unvented portable heater. It
-
Product Features
-
- Portable, stable and fully assembled.
-
- Wind resistant and rain protected.
- Continuous spark ignition or piezo spark ignition.
- 100% safety shut-off system.
- Adjustable input ratings (Except MH-40-GFA).
- Adjustable Height Controller.
DO NOT attempt to light heater
Extinguish any open flame
Shut off gas to heater
If odor continues, contact your local gas supplier or
fire department.
Do not touch any electric switch, do not use any
phone in your building
Immediately call your gas supplier from a neighbors
phone. Follow the gas suppliers instructions
If you can not reach your gas supplier, call the fire
department
Service must be done by a qualified service agency
or the gas supplier.
The state of California requires the following
warning:
Combustion by-products produced when using this product contain carbon monoxide, a chemical known to the state of California to cause cancer and birth defects (or other reproductive harm).
WARNING
PROPANE INFORMATION
The Propane (LP) cylinder must also be
equipped with the following:
- A collar to protect the gas valve.
- A shut-off valve terminating a LP cylinder
valve outlet as specified in the American
National Standard for Compressed Gas
Cylinder Valve Outlets and Inlet Connections.
- A safety relief valve having direct communications with the vapor space of the LP cylinder.
- An arrangement of vapor withdrawal.
Figure 1. Product Features
Page 2
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
General Safety Information
Indicates an imminently hazardous situaDANGER tion which, if not avoided, WILL result in
death or serious injury.
Indicates a potentially hazardous situation
WARNING which, if not avoided, COULD result in
death or serious injury.
Indicates a potentially hazardous situation
CAUTION which, if not avoided, MAY result in minor
or moderate injury.
Fire, burn, inhalation, and explosion
WARNING hazard. Keep solid combustibles such as
building materials, paper, or cardboard, at a safe distance
away from heater as recommended by the instructions.
Never use the heater in spaces which do or may contain
volatile or airborne combustibles or products such as
gasoline, solvents, paint thinner, dust particles, or unknown
chemicals.
WARNING
Not for home or recreational vehicle use.
Consumer: Retain these instructions for future reference.
Improper use of this heater can result in
DANGER serious injury or death from burns, fire,
explosion, electrical shock and /or carbon monoxide
poisoning.
This heater is designed and approved for use as a construction
heater in accordance with ANSI Z83.7a/CSA 2.14a-2007. Other
standards govern the use of fuel gases and heating products for
specific uses. Your local authority can advise you about these.
The primary purpose of construction heaters is to provide temporary heating of buildings under construction, alteration, or repair.
Properly used, the heater provides safe economical heating.
Products of combustion are vented into the area being heated.
WARNING Not for use with ductwork.
Do not operate this heater until you read and
WARNING thoroughly understand the safety and operating instructions.
CHECK WITH YOUR LOCAL FIRE SAFETY AUTHORITY IF YOU
HAVE ANY QUESTIONS ABOUT APPLICATIONS. This heater is
designed and approved for use as a construction heater under
ANSI Z83.7a/CSA 2.14a-2007.
Other standards govern the use of fuel gasses and heat producing products in specific applications. Your local authority can advise
you of these.
This is a direct-fired, forced-air construction heater for either
indoor or outdoor use. It's intended use is primarily for the
temporary heating of buildings under construction, alteration or
repair. All of the products of combustion generated by this heater
are forced through the heater and released into the area being
heated. This heater operates at approximately 98%+ combustion
efficiency, but still produces small amounts of carbon monoxide.
Humans can tolerate small amounts of carbon monoxide for short
periods. Carbon monoxide can build up in a heated space, and
failure to provide adequate ventilation could result in poisoning or
death.
You must provide the propane gas and cylinder(s). Use this
heater only with a propane vapor withdrawal supply system.
Refer to Chapter 5 of the Standard for Storage and Handling of
Liquefied Petroleum Gas , ANSI/NFPA 58. Your local library or
fire department will have this booklet.
IMPORTANT SAFETY INFORMATION
- Children should be kept away.
- Always maintain proper clearance from combustible materials.
Minimum clearance should be:
Sides - 24”
Top - 36”
Front - 72”
- Heater must be placed on level and solid footing.
- Never place anything, including clothes or other flammable items
on heater.
- Do not modify heater, or operate a heater that has been
modified.
Combustible by-products produced when
- Adequate clearance for accessibility, combustion and ventilation
(air supply) must be maintained at all times when heater is operating.
ide, a chemical known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The hose assembly shall be protected
WARNING from traffic, building material and contact
with hot surfaces both during use and while in storage.
- Service and repair should be performed by a qualified service
person. The heater should be inspected before each use, and at
least annually by a qualified person. More frequent cleaning may
be required as necessary. Do not service heater while hot or
operating.
WARNING using this product contain carbon monox-
IMPORTANT: Read this User's Manual carefully and completely
before attempting to operate or service this heater. Improper use
of the heater can cause serious injury or death from fire,
explosion and carbon monoxide poisoning.
Every possible circumstance that may involve a hazard cannot be
anticipated. The warnings in this manual and attached to the unit
are therefore not all-inclusive. If a procedure, work method or operating technique not specifically recommended by Pinnacle is used,
you must be sure it is safe for you and others. You should also
insure that equipment will not be damaged or made unsafe by the
operating or maintenance method you choose.
- Never connect heater to an unregulated gas supply.
- Use only the electrical/power cord specified. Electrical and
grounding connection must comply with National Electrical
Code - ANSI/NFPA 70 (USA) and CSA C22.1 Canadian
Electrical Code, Part 1 (Canada).
- To prevent injury, always wear gloves when handling heater.
Never handle an operating or hot heater, as severe burns may
result.
- Use heater in accordance with all local codes. In the absence
of local codes, refer to The National Fuel Code, ANSI Z223.1.
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Page 3
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
General Safety Information (Continued)
- This heater is shipped from the factory for use with LP
(propane) gas only. Do not convert to any other gas. Installation
must conform to local codes, or in their absence, with the standard for the Storage and Handling of Liquefied Petroleum Gases
ANSI/NFPA 58.
- Turn heater gas valve knob and LP cylinder valve to OFF position.
- LP cylinder valve equipped with old style fitting has LEFTHANDED THREADS. Turn fitting CLOCKWISE to loosen.
Protect this fitting when disconnected from LP cylinder.
- Have your LP cylinder filled by your local Propane gas supplier.
- Use only the regulator and hose assembly provided with this
heater. Inspect the regulator/hose assembly prior to each use of
the heater. If there is excessive abrasion or wear, or if the hose
is cut, replace it with the proper assembly shown in the parts
list, prior to using the heater.
- Some LP cylinders have a bleed-off valve. This valve should be
inspected for leaks after each filling of the LP cylinder. Turn the
valve clockwise to close.
- Gas supply connections should be checked by using a 50/50
soap and water solution. Never use a flame to check for gas
leaks.
- Locate LP cylinder at least 6 feet from the heater, and do not
direct heater discharge towards the LP cylinder unless it is at
least 20 feet from the heater.
- With heater gas valve knob still in OFF position, turn ON LP
cylinder valve and check for leaks with soap solution.
Propane is safe to use when properly hanCAUTION dled. Careless handling of the LP cylinder
could result in a fire and/or an explosion. Therefore:
- Always keep LP cylinder securely fastened and in an upright
position.
- The electrical connection and grounding must comply with the
National Electrical Code, ANSI/NFPA 70. Use only a properly
grounded three (3) prong receptacle.
- Do not restrict air inlet or outlet areas of the heater.
- Fasten full Propane tank and connect proper fitting to LP cylinder valve by turning COUNTERCLOCKWISE.
- Avoid tipping the LP cylinder on its side when connected to a
regulator, since this may cause damage to the diaphragm in the
regulator.
Operation
- Handle valves with care.
REFILLING THE LP CYLINDER
- Never connect an unregulated LP cylinder to a construction
heater.
ALL NEW LP CYLINDERS MUST BE PURGED BEFORE THE
FIRST FILLING.
Purging and filling of LP cylinders must be
WARNING performed by personnel who have been
thoroughly trained in accepted LP gas industry procedures.
Failure to follow these instructions may result in explosion,
fire, severe personal injury or death.
Average
Temp.(oF)
MH-40
MH-60V
20 or 100lb. 20 or 100lb.
cylinder
cylinder
MH-125V
MH-150V
100lb. cylinder
100lb. cylinder
32°
1
1
2
2
20°
1
1
2
2
10°
1
1
3
3
0°
1
1
3
3
-10°
2
2
Use larger
tank
Use larger
tank
-20°
2
2
Use larger
tank
Use larger
tank
Table 2: The table above shows the minimum number of 100 lb
LP cylinders required in cold weather. Your local LP dealer will
help you select the proper LP supply system.
Page 4
- Do not subject LP cylinder to excessive heat.
- Tightly close the gas shutoff valve on the LP cylinder after each
use.
- All fittings must be protected when disconnected from the LP
cylinder.
- Never store an LP cylinder inside a building or in the vicinity of
any gas burning appliance.
The disconnected tank must never be
CAUTION stored in a building, garage or any other
enclosed area.
- Do not restrict inlet or outlet of heater. Heater is never to be
used with ductwork.
Figure 2 Connecting Hose / Regulator to LP Cylinder
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
Operation (Continued)
SHUTDOWN INSTRUCTIONS
CHECKING FOR LEAKS
- To check for leaks, make up a 50/50 solution of dish soap and
water. Apply this solution to all gas connections. If bubbles
appear, there is a leak. If a leak is found, turn off the gas supply,
and re-connect the leaking connection. If the leak persists after
several tries, contact Pinnacle Customer Service at 215-8918460.
To shut off heater:
- The installation of this heater must meet all local codes and/or
gas utility requirements. In the absence of local codes, the
National Fuel Code ANSI Z223.1 should be followed.
- The minimum clearances to any combustible construction materials must be maintained at all times (See Page 3).
VENTILATION
1. Turn gas valve knob clockwise to OFF position.
2. Turn gas supply OFF by turning LP cylinder valve clockwise to
close.
3. Disconnect the power cord.
TEST FIRING THE HEATER
Test fire your construction heater following the lighting instructions
applicable to the gas control system employed.
Leak test all gas connections with 50/50 soap and water solution
prior to start-up. Soap bubbles indicate a gas leak. DO NOT use a
match or flame to test for gas leaks.
NOTE: Heater surface temperature must be cold before initiating
service, cleaning or storage.
STORAGE
CAUTION Always provide a fresh air opening in the heated space of at least three square feet (2,800 sq. cm.) for each
100,000 BTU/Hr of heater output. For example, a
MH-150V-GFA will require:
- a two-car garage door open 6 inches, or
- a single car garage open 9 inches, or
- two thirty two inch wide windows open 15 inches.
LIGHTING INSTRUCTIONS
1. Connect power cord to a properly grounded three (3) prong
120V, 60 Hz, extension cord.
Extension Cord Wire Requirements:
6 to 10 feet (1.8 to 3 meters) long, use 18 AWG conductor.
Always disconnect the heater from the LP cylinder before putting
the heater into storage. If for any reason the heater is to be
stored indoors, the tank MUST be disconnected from the LP
cylinder, and the cylinder stored outdoors in a well-ventilated
area, out of the reach of children, and in accordance with the
Standard for Storage and Handling of Liquefied Gases,
ANSI/NFPA 58 - latest edition. The plastic valve plug or valve
cover supplied with the cylinder must be re-installed on the valve
to protect the fitting from damage.
Never store an LP cylinder inside of a
building, or near any other gas or oil
burning appliances.
DANGER
NOTE: Installation and repair of this heater should be done
by a qualified service person.
11 to 100 feet (3.4 to 30.53 meters) long, use 16 AWG conductor.
101 to 200 feet (30.8 to 61 meters) long, use 14 AWG conductor.
2. Connect heater to a proper LP cylinder.
3. Turn gas valve clockwise to OFF position.
4. Wait five (5) minutes for any gas to clear. Smell for gas; if you
do not smell gas, go to Step 4.
5. Push in and turn gas control knob counterclockwise to
LOW/IGN position. This will light the burner. If needed, keep
pressing control knob until the burner lights and keep pressing
and turning from OFF to LOW/ IGN on Piezo electric spark
models (HIGH/IGN on Model MH-40-GFA).
Hose
6. Keep the valve knob depressed for at least 30 seconds after
lighting the burner. After 30 seconds, release valve knob.
Inlet Connector
7. If burner does not stay lit, repeat lighting procedure.
8. When burner stays lit, turn gas valve knob counterclockwise to
desired setting (All models except MH-40-GFA).
Figure 3. Connecting Hose to Heater Inlet
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Page 5
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
Wiring Diagrams
NOTE: If any original wiring as supplied with the
heater must be replaced, it must be with type AWG
105°C wire or its equivalent, except as indicated.
Figure 4. Wiring Diagram for Piezo/Manual Spark Models.
NOTE: If any original wiring as supplied with the heater must be replaced, it
must be with type AWG 105°C wire or its equivalent, except as indicated.
Figure 5. Wiring Diagram for Continuous Spark Models.
Repair Parts List for Propane Construction Heater
Reference
Number
Description
Part Number for Models:
MH-40-GFA
MH-60V-GFA
MH-125V-GFA
MH-150V-GFA
Quantity
1
2
3
4
5
6
7
8
9
10
Outer Shell
Inner Shell Assembly
Base
Height Controller
Base Cover
Inner Shell Cap
Multi Bracket Assembly
Thermal Switch
Tubing Assembly
Nozzle
22-524-0075
22-524-0004
22-501-0003
22-512-0005
22-508-0003
22-505-0006
22-504-0002
22-603-0001
22-605-0001
22-081-0007
22-524-0077
22-524-0005
22-501-0002
22-512-0008
22-508-0002
22-505-0011
22-504-0002
22-603-0001
22-605-0005
22-081-0015
22-524-0077
22-524-0005
22-501-0002
22-512-0008
22-508-0002
22-505-0008
22-504-0003
22-603-0001
22-605-0005
22-081-0004
1
1
1
1
1
1
1
1
1
1
Page 6
22-524-0076
22-524-0004
22-501-0001
22-512-0005
22-508-0001
22-505-0010
22-504-0002
22-603-0001
22-605-0001
22-081-0014
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
Exploded Drawing/Part Breakdown
2
6
7
12
8
1
13
14
16
17
15
10
11
21
9
23
22
26
18
20
3
25
19
24
4
Figure 6. Exploded View - All Models
5
27
28
Repair Parts List for Propane Construction Heater (Continued)
Reference
Number
Description
Part Number for Models:
MH-40-GFA
MH-60V-GFA
MH-125V-GFA
MH-150V-GFA
Quantity
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Nozzle Nut
Handle
Flange Hex Nut
Fan
Cushion Pad
Motor Assembly
Guard
Round Bolt
Valve Assembly
Inlet Connector
Spark Module
PCB Assembly
PCB Case
Valve Knob
Power Cord Assembly
Thermal Switch Cable
Hex Nut
Regulator Assembly
22-518-0001
22-511-0004
22-518-0003
22-514-0001
22-509-0001
22-061-0015
22-101-0003
22-503-0002
22-011-0005
22-507-0003
–
22-521-0001
22-506-0001
22-516-0001
22-131-0001
22-601-0001
22-518-0004
22-041-0004
22-518-0001
22-511-0005
22-518-0003
22-514-0002
22-509-0001
22-061-0016
22-101-0004
22-503-0003
22-011-0018
22-507-0003
22-604-0005
22-521-0002
22-506-0001
22-516-0001
22-131-0001
22-601-0001
22-518-0004
22-041-0005
22-518-0002
22-511-0005
22-518-0003
22-514-0002
22-509-0001
22-061-0016
22-101-0004
22-503-0003
22-011-0008
22-507-0003
22-604-0005
22-521-0002
22-506-0001
22-516-0001
22-131-0001
22-601-0001
22-518-0004
22-041-0005
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
22-518-0001
22-511-0005
22-518-0003
22-514-0001
22-509-0001
22-061-0015
22-101-0003
22-503-0002
22-011-0017
22-507-0003
22-604-0005
22-521-0002
22-506-0001
22-516-0001
22-131-0001
22-601-0001
22-518-0004
22-041-0004
Always be sure to follow proper maintenance procedures. This should include cleaning the inside the heater
once a month, and checking the spark gap at least once a heating season.
Pinnacle Products International, Inc. Propane Forced Air User’s Manual
Page 7
Propane
Forced Air Heaters
NEVER LEAVE HEATER UNATTENDED
WHILE BURNING, CONNECTED TO A
POWER SOURCE, OR WHILE
CONNECTED TO A FUEL SOURCE
Troubleshooting Guide
Problem
Fan does not turn when electricity is
connected
Heater will not fire (ignite)
Heater stops running by itself
Possible Cause
Solution
1. No electric power to heater
1. Check current at outlet. If voltage is correct,
inspect extension and power cords for cuts, frays
or breaks
2. Blades of fan in contact with heater
housing
2. Check housing for damage. Be sure there ar no
dents in the housing obstructing the fan
3. Fan blades bent
3. Straighten all fan blades
4. Fan motor defective
1. No spark at module
4. Replace Motor Assembly
1. Inspect module wire. Re-attach, or tighten if loose.
Inspect Spark module, and replace if necessary.
Inspect all other electrical components
2. Incorrect spark gap
2. Set plug gap to 0.16” (4mm)
3. Corroded electrode
3. Replace spark plug (Multi-Bracket Assembly)
1. Temperature inside heater is too high, 1. If heater input or output is restricted, the inside
causing thermal switch to shut down
temperature can become too hot. Keep the areas
operation
in front and behind heater clear of obstructions
2. Damaged control valve
2. Replace control valve (Valve Assembly)
3. Dust or debris accumulated in heater 3. Clean inside of heater
LIMITED WARRANTY
Pinnacle Products International, Inc. warrants this heater to
the original retail purchaser only, to be free from defects in material and workmanship for a period of one (1) year from the date of
initial purchase. This product must be properly installed, maintained and operated in accordance with the instructions provided.
Pinnacle Products International, Inc. requires reasonable proof
of your date of purchase from an authorized retailer or distributor.
Therefore, you should keep your sales slip, invoice, or cancelled
check from the original purchase. This Limited Warranty shall be
limited to the repair or replacement of parts, which prove defective under normal use and service within the warranty period, and
which Pinnacle Products International, Inc. shall determine at
its reasonable discretion.
This warranty does not apply to products purchased for rental
use.
This Limited Warranty does not cover any failures or operating
difficulties due to normal wear and tear, accident, abuse, misuse,
alteration, misapplication, improper installation or improper maintenance and service by you or any third party. Failure to perform
normal and routine maintenance on the heater, shipping damage,
damage related to insects, birds, or animals of any kind, and
damage due to weather conditions are also not covered. In addition, the Limited Warranty does not cover damage to the finish,
such as scratches, dents, discoloration, rust or other weather
damage, after purchase.
All transportation costs for the return of the damaged product or
parts will be the responsibility of the purchaser. Upon receipt of
damaged item, Pinnacle Products International, Inc. will examine the item and determine if defective. Pinnacle Products
International, Inc. will repair or replace and return the item,
freight pre-paid. If Pinnacle Products International, Inc. finds
the item to be in normal operating condition, or not defective, the
item will be returned freight collect.This Limited Warranty is in
lieu of all other express warranties. Pinnacle Products
International, Inc. disclaims all warranties for products that are
purchased from sellers other than authorized retailers or distributors.
AFTER THE PERIOD OF THE ONE (1) YEAR EXPRESS WARRANTY EXPIRES, Pinnacle Products International, Inc. DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR APPLICATION. FURTHER, Pinnacle Products International, Inc. SHALL
HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY
THIRD PARTY FOR ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. Pinnacle
Products International, Inc. assumes no responsibility for any
defects caused by third parties. This Limited Warranty gives the
purchaser specific legal rights; a purchaser may have other rights
depending upon where he or she lives. Some states do not allow
the exclusion or limitation of special, incidental or consequential
damages, or limitations on how long a warranty lasts, so the
above exclusion and limitations may not apply to you.
Pinnacle Products International, Inc. does not authorize any
person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return,
or replacement of its equipment, and no such representations are
binding on Pinnacle Products International, Inc.
Always be sure to specify model number and serial number when
making any claim with Pinnacle Products International, Inc.
For your convenience use the space provided below to list this
information:
Model #: ____________________
Serial #: _________________________
Date of Purchase: _________________