User Manual
Rack/Tower Online UPS
1K/1.5K/2K/3K
Uninterruptible Power Supply System
Table of Contents
1. Important Safety Warning ............................................................................................1
1-1. Transportation....................................................................................................1
1-2. Preparation ........................................................................................................1
1-3. Installation ........................................................................................................1
1-4. Operation ..........................................................................................................1
1-5. Maintenance, service and faults ...........................................................................2
2. Installation and setup ..................................................................................................3
2-1 Rear panel view ..................................................................................................3
2-2. Install the UPS ...................................................................................................4
2-3. Setup the UPS....................................................................................................4
2-4 Battery Replacement ...........................................................................................6
2-5 Battery Kit Assembly (option) ...............................................................................7
3. Operations .................................................................................................................9
3-1. Button operation ................................................................................................9
3-2. LCD Panel ..........................................................................................................9
3-3. Audible Alarm .................................................................................................. 11
3-4. LCD display wordings index ............................................................................... 11
3-5. UPS Setting ..................................................................................................... 11
3-6. Operating Mode Description .............................................................................. 14
3-7. Faults Reference Code ...................................................................................... 15
3-8. Warning indicator ............................................................................................. 16
4. Troubleshooting ........................................................................................................ 17
5. Storage and Maintenance .......................................................................................... 19
6. Specifications ........................................................................................................... 20
1. Important Safety Warning
Please comply with all warnings and operating instructions in this manual strictly. Save this
manual properly and read carefully the following instructions before installing the unit. Do not
operate this unit before reading through all safety information and operating instructions
carefully
1-1. Transportation
 Please transport the UPS system only in the original package to protect against shock
and impact.
1-2. Preparation
 Condensation may occur if the UPS system is moved directly from cold to warm
environment. The UPS system must be absolutely dry before being installed. Please
allow at least two hours for the UPS system to acclimate the environment.
 Do not install the UPS system near water or in moist environments.
 Do not install the UPS system where it would be exposed to direct sunlight or near
heater.
 Do not block ventilation holes in the UPS housing.
1-3. Installation
 Do not connect appliances or devices which would overload the UPS system (e.g.
laser printers) to the UPS output sockets.
 Place cables in such a way that no one can step on or trip over them.
 Do not connect domestic appliances such as hair dryers to UPS output sockets.
 The UPS can be operated by any individuals with no previous experience.
 Connect the UPS system only to an earthed shockproof outlet which must be easily
accessible and close to the UPS system.
 Please use only VDE-tested, CE-marked mains cable (e.g. the mains cable of your
computer) to connect the UPS system to the building wiring outlet (shockproof
outlet).
 Please use only VDE-tested, CE-marked power cables to connect the loads to the UPS
system.
 When installing the equipment, it should ensure that the sum of the leakage current
of the UPS and the connected devices does not exceed 3.5mA.
1-4. Operation
 Do not disconnect the mains cable on the UPS system or the building wiring outlet
(shockproof socket outlet) during operations since this would cancel the protective
earth of the UPS system and of all connected loads.
 The UPS system features its own, internal current source (batteries). The UPS output
sockets or output terminals block may be electrically live even if the UPS system is not
connected to the building wiring outlet.
 In order to fully disconnect the UPS system, first press the OFF/Enter button to
disconnect the mains.
 Prevent no fluids or other foreign objects from inside of the UPS system.
1
1-5. Maintenance, service and faults
 The UPS system operates with hazardous voltages. Repairs may be carried out only
by qualified maintenance personnel.
 Caution - risk of electric shock. Even after the unit is disconnected from the mains
(building wiring outlet), components inside the UPS system are still connected to the
battery and electrically live and dangerous.
 Before carrying out any kind of service and/or maintenance, disconnect the batteries
and verify that no current is present and no hazardous voltage exists in the terminals
of high capability capacitor such as BUS-capacitors.
 Only persons are adequately familiar with batteries and with the required
precautionary measures may replace batteries and supervise operations.
Unauthorized persons must be kept well away from the batteries.
 Caution - risk of electric shock. The battery circuit is not isolated from the input
voltage. Hazardous voltages may occur between the battery terminals and the
ground. Before touching, please verify that no voltage is present!
 Batteries may cause electric shock and have a high short-circuit current. Please take
the precautionary measures specified below and any other measures necessary when
working with batteries:
-remove wristwatches, rings and other metal objects
-use only tools with insulated grips and handles.
 When changing batteries, install the same number and same type of batteries.
 Do not attempt to dispose of batteries by burning them. This could cause battery
explosion.
 Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin
and eyes. It may be toxic.
 Please replace the fuse only with the same type and amperage in order to avoid fire
hazards.
 Do not dismantle the UPS system.
2
2. Installation and setup
NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is
damaged. Please keep the original package in a safe place for future use.
NOTE: There are two different types of online UPS: standard and long-run models. Please
refer to the following model table.
Model No.
Type
Model No.
Type
1K
1KL
1.5K
1.5KL
Standard
Long-run
2K
2KL
3K
3KL
2-1 Rear panel view
1K/1.5K IEC
2K IEC
3K IEC
1K/1.5K NEMA
2K NEMA
3K NEMA
1. Programmable outlets: connect to non-critical loads.
2. Output receptacles: connect to mission-critical loads.
3. AC input
4. Input circuit breaker
5. Network/Fax/Modem surge protection
6. Emergency power off function connector (EPO)
7. USB communication port
8. RS-232 communication port
9. SNMP intelligent slot
10. External battery connector (only available for long-run models)
11. Input terminal
12. Output circuit breaker
3
2-2. Install the UPS
For safety consideration, the UPS is shipped out from factory without connecting battery wires.
Before install the UPS, please follow below steps to re-connect battery wires first.
Step 1
Step 2
Step 3
Remove front panel.
Connect the AC input and
re-connect battery wires.
Put the front panel back to the
unit.
This UPS can be either displayed on the desk or mounted in the 19” rack chassis. Please choose
proper installation to position this UPS.
Rack-mount Installation
Step 1
Tower Installation
Step 1
Step 2
Step 2
Step 3
2-3. Setup the UPS
Step 1: UPS input connection
Plug the UPS into a two-pole, three-wire, grounded receptacle only. Avoid using extension
cords.
Step 2: UPS output connection
 For socket-type outputs, there two kinds of outputs: programmable outlets and general
outlets. Please connect non-critical devices to the programmable outlets and critical
devices to the general outlets. During power failure, you may extend the backup time to
critical devices by setting shorter backup time for non-critical devices.
4
Step 3: Communication connection
Communication port:
USB port
RS-232 port
Intelligent slot
To allow for unattended UPS shutdown/start-up and status monitoring, connect the
communication cable one end to the USB/RS-232 port and the other to the communication
port of your PC. With the monitoring software installed, you can schedule UPS
shutdown/start-up and monitor UPS status through PC.
The UPS is equipped with intelligent slot perfect for either SNMP or AS400 card. When
installing either SNMP or AS400 card in the UPS, it will provide advanced communication and
monitoring options.
PS. USB port and RS-232 port can’t work at the same time.
Step 4: Network connection
Network/Fax/Phone surge port
Connect a single modem/phone/fax line into surge-protected “IN” outlet on the back panel of
the UPS unit. Connect from “OUT” outlet to the equipment with another modem/fax/phone line
cable.
Step 5: Disable and enable EPO function
Keep the pin 1 and pin 2 closed for UPS normal operation. To activate EPO function, cut the
wire between pin 1 and pin 2.
It’s in closed status for UPS
normal operation.
Step 6: Turn on the UPS
Press the ON/Mute button on the front panel for two seconds to power on the UPS.
Note: The battery charges fully during the first five hours of normal operation. Do not
expect full battery run capability during this initial charge period.
Step 7: Install software
For optimal computer system protection, install UPS monitoring software to fully configure UPS
shutdown. Please follow steps below to download and install monitoring software:
1. Go to the website http://www.power-software-download.com
2. Click ViewPower software icon and then choose your required OS to download the software.
3. Follow the on-screen instructions to install the software.
4. When your computer restarts, the monitoring software will appear as an orange plug icon
located in the system tray, near the clock.
5
2-4 Battery Replacement
NOTICE: This UPS is equipped with internal batteries and user can replace the batteries
without shutting down the UPS or connected loads.(hot-swappable battery design)
Replacement is a safe procedure, isolated from electrical hazards.
CAUTION!! Consider all warnings, cautions, and notes before replacing batteries.
Note: Upon battery disconnection, equipment is not protected from power outages.
Step 1
Step 2
Step 3
Remove front panel.
Disconnect battery wires.
Step 4
Step 5
Pull out the battery box by
removing two screws on the
front panel.
Step 7
Remove the top cover of
battery box and replace the
inside batteries.
After replacing the
Re-connect the battery wires.
batteries, put the battery
box back to original location
and screw it tightly.
Step 8
Put the front panel back to the unit.
6
2-5 Battery Kit Assembly (option)
NOTICE: Please assemble battery kit first before installing it inside of UPS. Please select
correct battery kit procedure below to assemble it.
2-battery kit
Step 1: Remove adhesive tapes.
Step 2: Connect all battery terminals by
following below chart.
Tapes
Step 3: Put assembled battery packs on
one side of plastic shells.
3-battery kit
Step 1: Remove adhesive tapes.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
Step 2: Connect all battery terminals by
following below chart.
Tapes
Tapes
Step 3: Put assembled battery packs on
one side of plastic shells and insert one
more defect battery on the space.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
Defect
battery
7
4-battery kit
Step 1: Remove adhesive tapes.
Step 2: Connect all battery terminals by
following below chart.
Tapes
Tapes
Step 3: Put assembled battery packs on
one side of plastic shells.
6-battery kit
Step 1: Remove adhesive tapes.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
Step 2: Connect all battery terminals by
following below chart.
Tapes
Tapes
Step 3: Put assembled battery packs on
one side of plastic shells.
Step 4: Cover the other side of plastic shell as
below chart. Then, battery kit is assembly well.
8
3. Operations
3-1. Button operation
Button View
Button
Function
 Turn on the UPS: Press and hold ON/Mute button for at least 2
seconds to turn on the UPS.
 Mute the alarm: After the UPS is turned on in battery mode, press
and hold this button for at least 5 seconds to disable or enable the
alarm system. But it’s not applied to the situations when warnings or
ON/Mute Button
errors occur.
 Up key: Press this button to display previous selection in UPS setting
mode.
 Switch to UPS self-test mode: Press ON/Mute buttons simultaneously
for 5 seconds to enter UPS self-testing while in AC mode, ECO mode,
AECO mode, or converter mode.
 Turn off the UPS: Press and hold this button at least 2 seconds to turn
off the UPS in battery mode. UPS will be in standby mode under
power normal or transfer to bypass mode if the Bypass enable setting
OFF/Enter Button
by pressing this button.
 Confirm selection key: Press this button to confirm selection in UPS
setting mode.
 Switch LCD message: Press this button to change the LCD message
for input voltage, input frequency, battery voltage, output voltage,
output frequency.
Select Button
 Setting mode: Press and hold this button for 5 seconds to enter UPS
setting mode when Standby and Bypass mode.
 Down key: Press this button to display next selection in UPS setting
mode.
 Switch to bypass mode: When the main power is normal, press
ON/Mute + Select
ON/Mute and Select buttons simultaneously for 5 seconds. Then UPS
Button
will enter to bypass mode. This action will be ineffective when the
input voltage is out of acceptable range.
3-2. LCD Panel
Rack Display
Load info
Input/output
and Battery
info
UPS status
Tower Display
Battery info
Battery info
Warning
& Fault info/
Setting
operation
Backup
time
info
Load info
9
Input/output
and Battery
info
Warning & Fault info/
Setting operation
UPS status
Backup time
info
Display
Function
Backup time information
Indicates the backup time in pie chart.
Indicates the backup time in numbers.
H: hours, M: minute
Warning & Fault information
Indicates that the warning and fault occurs.
Indicates the warning and fault codes, and the codes are
listed in details in 3-5 section.
Setting Operation
Indicates the setting operation.
Input/Output & Battery information
Indicates the output/input voltage, output/input frequency,
and battery voltage.
V: voltage, Hz: frequency
Load information
Indicates the load level by 0-25%, 26-50%, 51-75%, and
76-100%.
Indicates overload.
Indicates the load or the UPS output is short circuited.
UPS status
Indicates that programmable management outlets are
working.
Indicates the UPS working in line mode.
Indicates the UPS is working in converter mode.
Indicates the UPS is working in bypass mode.
Indicates the UPS powers the output directly from the mains
Indicates that the UPS alarm is disabled.
Indicates the battery charger is working.
Battery information
Indicates the Battery level by 0-25%, 26-50%, 51-75%, and
76-100%.
Indicates low battery.
Indicates there is something wrong with battery.
10
3-3. Audible Alarm
Battery Mode
Sounding every 4 seconds
Low Battery
Sounding every second
Overload
Sounding twice every second
Fault
Continuously sounding
3-4. LCD display wordings index
Abbreviation
Display content
Meaning
ENA
Enable
DIS
Disable
ESC
Escape
RAC
Rack display
TOE
Tower display
B.L
Low Battery
O.L
Overload
N.C
Battery is not connected
O.C
Overcharge
SF
Site Fault
E.P
EPO
T.P
Over Temperature
C.H
Charger Failure
B.B
Battery Fault
F.U
Frequency Unstable in Bypass Mode
B.V
Input Voltage is Out of Bypass Range
3-5. UPS Setting
There are two parameters to set up the
UPS.
Parameter 1: It’s for program
alternatives. There are 9 programs to
set up:
Parameter 2: It’s for setting
information display。
Parameter 2
Parameter 1
11
 01: Output voltage setting
Interface
Setting
For 208/220/230/240 VAC models, you may choose the following
output voltage:
208: presents output voltage is 208Vac
220: presents output voltage is 220Vac
230: presents output voltage is 230Vac
240: presents output voltage is 240Vac
For 110/150/120/127 VAC models, you may choose the following
output voltage:
110: presents output voltage is 110Vac
115: presents output voltage is 115Vac
120: presents output voltage is 120Vac
127: presents output voltage is 127Vac
 02: Frequency Converter enable/disable
Interface
Setting
CF ENA: converter mode enable
CF DIS: converter mode disable
 03: Output frequency setting
Interface
Setting
You may set the initial frequency on battery mode:
BAT 50: presents output frequency is 50Hz
BAT 60: presents output frequency is 60Hz
If converter mode enable, you may choose the following output
frequency:
CF 50: presents output frequency is 50Hz
CF 60: presents output frequency is 60Hz
 04: ECO enable/disable
Interface
Setting
ENA: ECO mode enable
DIS: ECO mode disable
12
 05: AECO enable/disable
Interface
Setting
ENA: Advanced ECO mode enable
DIS: Advanced ECO mode disable
 06: Bypass mode enable/disable
Interface
Setting
ENA: Bypass mode enable
DIS: Bypass mode disable
 07: Programmable outlets enable/disable
Interface
Setting
ENA: Programmable outlets enable
DIS: Programmable outlets disable
 08: Programmable outlets setting
Interface
Setting
0-999: setting the backup time limits in minutes from 0-999 for
programmable outlets which connect to non-critical devices on
battery mode.
13
 09: LCD display direction setting
Interface
Setting
RAC: the LCD display is horizontal.
TOE: the LCD display is vertical.
 10: Acceptable input voltage range setting
Interface
Setting
For 208/220/230/240 VAC models, you may choose the following
Acceptable input voltage range:
110/300 alternating flashing: acceptable input voltage range is
from 110V to 300V;
160/260 alternating flashing: acceptable input voltage range is
160V to 260V;
170/270 alternating flashing: acceptable input voltage range is
170V to 270V;
For 110/150/120/127 VAC models, you may choose the following
Acceptable input voltage range:
55/150 alternating flashing: acceptable input voltage range is
from 55V to 150V;
80/130 alternating flashing: acceptable input voltage range is 80V
to 130V;
85/135 alternating flashing: acceptable input voltage range is 85V
to 135V;
 00: Exit setting
3-6. Operating Mode Description
Operating Description
mode
Online mode When the input voltage is within
acceptable range, UPS will provide
pure and stable AC power to output.
The UPS will also charge the battery at
online mode.
ECO mode
(Efficiency
Corrective
Optimizer)
When the input voltage is within
setting range (±3%Vo max), UPS will
bypass voltage to output for energy
saving. PFC and INVERTER are still
active at this mode.
14
LCD display
Rack Display
Tower Display
AECO mode
(Advanced
Efficiency
Corrective
Optimizer)
When the input voltage is within
setting range (±3%Vo max), UPS will
bypass voltage to output for energy
saving. PFC and INVERTER are off at
this mode.
Frequency
Converter
mode
(Rack)
When input frequency is within 40 Hz
to 70 Hz, the UPS can be set at a
constant output frequency, 50 Hz or
60 Hz. The UPS will still charge
battery under this mode.
Battery
mode
When the input voltage is beyond the
acceptable range or power failure and
alarm is sounding every 4 second,
UPS will backup power from battery.
Bypass
mode
When input voltage is within
acceptable range but UPS is
overload, UPS will enter bypass mode
or bypass mode can be set by front
panel. Alarm is sounding every 10
second.
Standby
mode
UPS is powered off without output
power, but the battery still can be
charged.
Fault mode
The UPS is in fault mode when no
output power is supplied from the
UPS and the fault icon flashes on the
LCD display, although the information
of UPS can be displayed in the
screen.
3-7. Faults Reference Code
Fault event
Bus
Bus
Bus
Bus
start fail
over
under
unbalance
Inverter soft start fail
High Inverter voltage
Fault
code
01
02
03
04
Icon
Fault event
Icon
Low Inverter voltage
Inverter output short
Battery voltage too high
Battery voltage too low
Fault
code
13
14
27
28
x
x
x
x
11
12
x
x
Over temperature
Overload
41
43
x
15
x
x
3-8. Warning indicator
Warning
Icon (flashing)
Low Battery
Code
Alarm
Sounding every second
Overload
Sounding twice every second
Battery is not connected
Sounding every second
Overcharge
Sounding every second
Site wiring fault
Sounding every second
EPO enable
Sounding every second
Over temperature
Sounding every second
Charger failure
Sounding every second
Battery Fault
Sounding every second
Bypass Out Range
Sounding every second
Bypass Frequency Unstable
Sounding every second
16
4. Troubleshooting
If the UPS system does not operate correctly, please solve the problem by using the table
below.
Symptom
Possible cause
Remedy
No indication and alarm even
The AC input power is not Check if input power cord
though the main is normal.
connected well.
firmly connected to the
mains.
The AC input is connected Plug AC input power cord
to the UPS output.
to AC input correctly.
The icon
and the warning
code
flashing on LCD
display and alarm is sounding
every second.
The icon
and
flashing
on LCD display and alarm is
sounding every second.
EPO function is activated.
Set the circuit in closed
position to disable EPO
function.
Line and neutral
conductors of UPS input
are reversed.
Rotate mains power socket
by 180° and then connect
to UPS system.
The external or internal
Check if all batteries are
The icon
and
flashing
battery is incorrectly
connected well.
on LCD display and alarm is
connected.
sounding every second.
Fault code is shown as 27 and the Battery voltage is too high Contact your dealer.
or the charger is fault.
icon
is lighting on LCD
display and alarm is continuously
sounding.
Fault code is shown as 28 and the Battery voltage is too low Contact your dealer.
or the charger is fault.
icon
is lighting on LCD
display and alarm is continuously
sounding.
Remove excess loads from
UPS output.
UPS is overloaded. Devices Remove excess loads from
connected to the UPS are
UPS output.
fed directly by the
electrical network via the
Bypass.
After repetitive overloads, Remove excess loads from
the UPS is locked in the
UPS output first. Then shut
Bypass mode. Connected
down the UPS and restart
devices are fed directly by it.
the mains.
Fault code is shown as 43 and The The UPS shut down
Remove excess loads from
icon
is lighting on LCD automatically because of
UPS output and restart it.
display and alarm is continuously overload at the UPS
sounding.
output.
The icons of
and
are flashing on LCD display and
alarm is sounding twice every
second.
UPS is overload
17
Symptom
Possible cause
Fault code is shown as 14 and
alarm is continuously sounding.
The UPS shut down
automatically because
short circuit occurs on the
UPS output.
Fault code is shown as 01, 02, 03, A UPS internal fault has
04, 11, 12, 13 and 41 on LCD
occurred. There are two
display and alarm is continuously possible results:
sounding.
1. The load is still supplied,
but directly from AC power
via bypass.
2. The load is no longer
supplied by power.
Battery backup time is shorter
Batteries are not fully
than nominal value
charged
Batteries defect
18
Remedy
Check output wiring and if
connected devices are in
short circuit status.
Contact your dealer
Charge the batteries for at
least 5 hours and then
check capacity. If the
problem still persists,
consult your dealer.
Contact your dealer to
replace the battery.
5. Storage and Maintenance
5-1. Operation
The UPS system contains no user-serviceable parts. If the battery service life (3~5 years
at 25°C ambient temperature) has been exceeded, the batteries must be replaced. In this
case, please contact your dealer.
Be sure to deliver the spent battery to a recycling facility or ship it to your
dealer in the replacement battery packing material.
Storage
Before storing, charge the UPS 5 hours. Store the UPS covered and upright in a cool, dry
location. During storage, recharge the battery in accordance with the following table:
Storage Temperature
Recharge Frequency
Charging Duration
-25°C - 40°C
Every 3 months
1-2 hours
40°C - 45°C
Every 2 months
1-2 hours
19
6. Specifications
MODEL
Capacity
VA
W
1K
1KL
1.5K
1.5KL
2K
2KL
3K
3KL
1000 VA
900 W
1000 VA
800W
1500 VA
1350 W
1500 VA
1200 W
2000 VA
1800 W
2000 VA
1600 W
3000 VA
2700 W
3000 VA
2400 W
INPUT
Low Line
Transfer
Low Line
Voltage
Comeback
Range
High Line
Transfer
High Line
Comeback
Frequency Range
Power Factor
OUTPUT
Output Voltage
AC Voltage Regulation
Frequency Range
Frequency Range
Current Crest Ratio (CF)
Harmonic Distortion
(THDU)
AC to DC
Inverter to
Bypass
Waveform (Batt. Mode)
EFFICIENCY
AC Mode
Battery Mode
BATTERY
Battery Type
Transfer
Time
Numbers
Typical Recharge Time
Charging Current (max.)
Charging Voltage
INDICATORS
LCD
ALARM
Battery Mode
Low Battery
Overload
Fault
PHYSICAL
Dimension, DxWxH (mm)
Net Weight (kgs)
ENVIRONMENT
Humidity
Noise Level
MANAGEMENT
Smart RS-232/USB
Optional SNMP
80 VAC/70 VAC/60 VAC/55 VAC ± 5 % or 160 VAC/140 VAC/120 VAC/110 VAC ± 5 %
(based on load percentage 100%-80% / 80%-70% / 70%-60% / 60%-0)
85 VAC/75 VAC/65 VAC/60 VAC ± 5 % or 170 VAC / 150 VAC / 130 VAC / 120 VAC ± 5 %
150 VAC ± 5 % or 300 VAC ± 5 %
140 VAC ± 5 % or 290 VAC ± 5 %
40Hz ~ 70Hz
≧0.99 @normal voltage
110/115/120/127 VAC or 208/220/230/240 VAC
± 1%
47 ~ 53 Hz or 57 ~ 63 Hz (Synchronized Range)
50Hz  0.5% or 60Hz  0.5% (Bat. Mode)
5:1 (max.)
≦ 2% (Linear load)
≦ 2% (Linear load)
8% max (Batt. mode before shut down)
8% max (Batt. mode before shut down)
Zero
4 ms (Typical)
Pure Sinewave
86% (typical), 88% (peak)
83% (typical), 86% (peak)
88% (typical), 90% (peak)
85% (typical), 88% (peak)
Depending
Depending
Depending
Depending
12V/9Ah
12V/9Ah
12V/9Ah
on
on
on
on
2
3
4
6
application
application
application
application
4 hours recover to 90% capacity (for standard model only)
1A
8A or 4A
1A
8A or 4A
1A
8A or 4A
1A
8A or 4A
27.4 VDC ± 1%
41.1 VDC ± 1%
54.7 VDC ± 1%
82.1VDC ± 1%
12V/9Ah
UPS status, Load level, Battery level, Input/Output/battery info, Discharge time and Fault indicators
Sounding every 4 seconds
Sounding every second
Sounding twice every second
Continuously sounding
380 x 438 x 88
12.9
8.6
480 x 438 x 88
17.6
10.7
480 x 438 x 88
20.6
11.3
600 x 438 x 88
28
13.8
20-90 % RH @ 0- 40°C (non-condensing)
Less than 50dBA @ 1 Meter
Supports Windows 2000/2003/XP/Vista/2008/7, Linux, Unix, and MAC
Power management from SNMP manager and web browser
20