Rcom USB 50 User`s manual

-PWFPGMJGFCFHJOTXJUI3DPN
REV. 3.0
DIGITAL EGG INCUBATOR
USER'S MANUAL
USB 50 / PRO 50
WATE
R
PULL OP
EN
Contents
How to use Rcom USB 50 / Rcom PRO 50
1. Introduction
(1) Rcom 50 Introduction
(
(2) Safety Precautions
)
(3) Identification of Parts
*
(4) Basic Components
+
(5) Function of Digital Control & How to Operate
,
(6) SET UP(Other Functions) / Easy Function Operation
-
Introduction
2. Before use
(1) How to Assemble the Incubator / Egg-Turning plate
%$
Before use
(2) What is an incubation room? / Preparation for Incubation %%r%&
3. Function Settings
(1) Incubation Modes / Incubation start with Automatic Mode
(2) Incubation start with Manual Mode
%'
%(r%)
(3) Incubation start for Other Birds
%*
(4) Incubation start with PC connection Mode
%+
Termination / Change Cels.& Fahr. /
(5) Incubation
Return to Factory Setting
conditions reset / How to Set Egg Turning Test /
(6) Incubation
How to Set Turn ON, OFF Humidification Function
Function Settings
%+
%,
4. Other Functions
Turning Check / Alarm for water supplement /
(1) Egg
Abnormal High or Low temperatue Alarm / Power Failure Alarm Function
5
Other Functions
%-
%*(*5"-*/$6#"503
Contents
How to use Rcom USB 50 / Rcom PRO 50
5. Incubation
(1) Humidity & Air Maintenance during Incubation /
&$
Maintenance after Hatching
(2) Dew Condensation
Introduction
&$
6. How to Clean
(1) How to Disassemble
&%
(2) How to Clean
&&
How to Clean
7. Product Information
(1) Servicing / Frequently Asked Questions (FAQ)
&'
Product Information
(2) Troubleshooting
&(
(3) Specification
&)
The result of Hatching can be changed by a large numbers of factors. Autoelex Co., Ltd. &
our distributors will not take any responsibility for ‘Loss of eggs or pet/animal lives’ under any
circumstances such as ‘Hatching/Brooding failures’, ‘User’s carelessness’, ‘Personal (un-certificated)
conversion / alteration’, ‘Arbitrary using out of the machine’s purpose’, ‘Electric power failure’, or
‘Malfunctioning’. Please be sure that the machine works without any problem before placing Eggs or
Pets(Animals). Also, we strongly recommend you to read the User’s Manual carefully to minimize of
any failure.
Mark Explanation
Caution : Caution mark against a fault that can cause damage, trouble, or failure of incubation.
Tip :
Prohibited
It is necessary to keep.
Do not disassemble.
Remove the power cord from outlet.
Do not touch.
Ground Connection for preventing electric shock.
References or useful suggestions in using Rcom product
Warning of actions which may be dangerous or cause damage to the incubator.
㷙 For Rcom USB 50 MODEL PC connecting, refer to the PC-SOFTWARE manual.
%*(*5"-*/$6#"503
6
1. Introduction
(1) Rcom 50 Introduction
Rcom 50
Thank you for choosing the Rcom incubator.
The Rcom 50 incubator is the first incubator with creditability to have a superior design and function
which help in controlling optimum incubation conditions. It has two sensors, one for detecting
surrounding environments and the another for internal incubator conditions.
The Rcom50 is designed easy to use and simple to use as a customer orientated product, but please
remember that the user's incubation knowledge and proper operation are very important for the best
incubation result. Therefore, be sure to read this user's manual carefully before you use this incubator.
The Rcom 50 offers optimum incubation conditions, but users need to observe and manage all
incubation conditions such as species of eggs, temperature or humidity for each incubation period, and
an optimum incubation circumstances .
Features
[Main Features]
* LCD display with incubation information, and animation graphic design
* Micro chip with optimum incubation conditions according to the species of birds, for incubation beginners
* Manual setting Mode for incubation specialists
* Outer Temp. Sensor included for Automatic Adjustment of Heating rate responding to Incubation Room
Temperature
* Superior design with convenient operation
* Optimum air circulation technique with 5 strong BLDC fans
* Automatic Temp. & Humidity setting and control
* Body locking device
* Water supplement alarm function
* 48 eggs capacity for chicken size eggs ( 116 Quail egg size / 24Goose egg size)
* Antiblastic Humidification method by heating water, which discourages bacterial growth
* Double-glazed view window for minimizing the influence of outside temperature
* Enhanced reliability by applying Swiss's Sensirion's 3rd generation temperature & humidity sensor
* Strong SMPS application for stable power supply
* Upgrade to the latest model incubator with program upgrade (USB MODEL ONLY)
[Safety Features]
* Self-examination function for sensing abnormal conditions
* Alarm and display function for abnormal incubator temperature caused by sudden fluctuation of ambient
temperature
* Incubation data memory function and power outage notification function in case of power failure
* Circulation fan cover for safety and electric safety cut-out switch on the upper main body for safety
* Heater supporter designed for heater tension control and its safety
* Safety cover applied for protecting humidification unit
* Humidification unit durability improved by water proof BLDC fan
* Alarm when water need replenishing
[Easy Features]
* No need of separate humidification unit as it included in main body
Û&RUÛ)FRQYHUWLEOH
* Various kinds of egg trays accept various sized eggs with ease
* Slide plate with embossed feature for preventing skid
* Variable air vent for adjusting air supply
* Bottom body designed for easy cleaning
* Roller Dividers, which can safely apply egg turning for expensive or rare eggs. (Option)
7
%*(*5"-*/$6#"503
1. Introduction
Electrical hazards
Do not use a damaged power Do not pull the cord when
cord or loose outlet.
taking out the power cord, and
▶ Risk of electric shock or fire. keep wet hands away from
connecting plug.
▶ Risk of electric shock or fire.
Setting Cautions
(2) Safety Precautions
Be careful the details below when you use.
Never pull the plug out of the
outlet during the incubation
period.
Do not install in moist or
humid environment.
▶ Risk of damage or fire within
the incubator.
▶ Risk of fire or interference
with the incubation process.
▶ Risk of fire or electric shock.
Do not cover the ventilating
opening.
Install away from heat
sources.
▶ Inner temperature can rise,
interrupting incubation.
▶ Risk of damage to the
incubator case and
interference with the
incubation process.
Ensure that the incubator is
installed on a stable surface
away from edges.
Do not disassemble or modify
the incubator in any way.
Please ensure that no small
objects get into
the holes on the incubator.
If the incubator sounds
strange or emits smoke
contact your service center.
▶ Risk of electric shock or fire.
▶ Risk of electric shock or fire.
Do not spray cleanser directly
on the incubator surface.
Clean the incubator by a soft
cloth with a neutral detergent.
▶ Risk of electric shock or fire.
▶ Risk of fire or electrical
overload.
Be careful the details below when you use.
Do not install under the direct
sunlight.
Cleaning Cautions
Do not insert multiple
connecting plugs in an outlet.
▶ Incubation will be interrupted.
Do not install in dusty or dirty
environment.
▶ Risk if electric shock or fire.
Do not twist or crush electric
cord.
▶ Risk of damage to incubator
and eggs and user from
accidental knocks or drops.
Do not install in excessively
cold or hot conditions,
cigarette smoke, etc.
Do not use any other
non-standard parts except
those provided.
▶ Risk of interference with
the incubation process.
▶ Risk of damage or hatching
failure.
Do not turn the incubator
upside down.
Children should be supervised
to ensure that they do not play
with the appliance.
▶ Water will pour out of the
incubator, and view window ▶ Risk of knocking the incubator
or accidental interference with
can be dropped or damaged.
the controls.
Clean the incubator thoroughly If the incubator requires repair
before storing.
disconnect from the power
supply and please contact to
your service center.
Be sure to disconnect the electric cord
from the outlet before cleaning.
Brush away dust on the plug
with a dry cloth.
Do not use chemicals like wax, For special cleaning of inner
benzene, alcohol, thinner,
part per year, contact to the
aromatic, or lubricant, etc.
service center.
▶ If you don't clean the inside of
incubator for a long time, dust
can cause some trouble or a fire.
%*(*5"-*/$6#"503
8
(3) Identification of Parts and
Compositio
1. Introduction
Identification of Parts
Handle
View Window
For a clear view of
the incubation process.
(Double Skin Viewing Window)
Serial No.
(EX:RCM0950278)
Power Connecting (the rear)
Egg Tray
For connecting
power cord.
Vents for air circulation
Small, Standard,
or Large egg tray
according to egg size.
Universal Tray
(Sold separately)
For circulating warm air
Air inlet vent
For inlet of air
from outside
WATER
Water hole
To facilitate water top-up
for the humidity control.
Main Body-1
PULL OPEN
Locking Button
Digital Control Center
See description of
the function and operation.
Main Body-2
#BDL
PASS
Calibration
PULL OPEN
110V~120V
RCM 0901278
PULL OPEN
Product Serial No.
USB Cable Connecting Socket
Connecting the USB cable.
You can set and store
incubation conditions
with your Computer.
< USB MODEL Only >
9
Power Connecting Socket
Connecting the electric cord
(EX:RCM0950278)
If you register your information
with your machine’s serial
number on our web-site
(www.Rcom.co.kr), you can get
2 year warranty service.
%*(*5"-*/$6#"503
1. Introduction
(4) Basic Components
Basic Components
Main Body-2
Main Body-1
WATER
Water Cap
Egg-Turning Plate
User's Manual
View Window
Small Egg Tray
Duplicated
View Window
Easy function
operation
Power Cord
Standard Egg Tray
* Can be attached
anywhere for
easy viewing
< USB MODEL >
Large Egg Tray
Gc`XGYdUfUhY`m
PC SOFTWARE CD
Universal Tray
Divider(10EA)
Universal Tray SET
Rolling Divider SET
USB Cable
ઔ USB MODEL - You can download updated information at www.Rcom.co.kr
%*(*5"-*/$6#"503
:
(5) Function of Digital Control &
How to Operate
1. Introduction
Function of Digital Control & How to Operate
Phqx#Exwwrq
Xs#Exwwrq
Select Birds
Incubation Termination
Temp. & Humidity UP
Setting Value Change
Vhohfw#Exwwrq
Grzq#Exwwrq
Select Auto/Manual
Pass to next stage
Temp. & Humidity DOWN
Setting Value Change
Lqsxw#Exwwrq
Ixqfwlrq#Exwwrq
Other function display,
Return to previous stage
Save input and
Pass to next stage
Setting Value Check
Egg Turning Interval Indication
Egg Turning Angle Indication
What’s ‘Temperature&Humidity Setting’?
This is that you set up temp.&humi. As you want to have inside of the machine.
NAME AND FUNCTION
ICON
ICON
NAME AND FUNCTION
--Fkrrvh#d#nlqg--#Fklfnhq#举
-#Gxfn#丿#
-#Txdlo#乀#
-#Skhdvdqw#乁#
-#Shdirzo#乂#
-#Jrrvh#乃#
-#zlogjrrvh#乄#
-#J0Skhdvdqw#久#
-#Wxunh|#乆#
-#Rwkhuv#Elugv#乇#
Egg Turning Indication
Fklfnhq
Species of Birds
FAN Operation Display
Current Temperature Display
Temperature Abnormal Display
Heater Stop Display
Heater Operation Display
Current Humidity Display
Humidification function OFF
Humidification Stop Display
Humidification Operation
Display
Egg Turning Interval Indication
Egg Turning Angle Indication
Water Supplement
Humidity Abnormal
PC Connecting
Alarm
Power Failure Notification
Bird Icon Display
60
90ȋ
< USB MODEL >
;
RII
Manual Egg Turning Stop
Indication
Automatic Egg Turning Stop
Indication
Incubation Termination
%*(*5"-*/$6#"503
(6) SET UP(Other Functions) /
Easy Function Operation
1. Introduction
▶ Push SET UP key and then select each function icon using
UP/DOWN key(ENTER)
SET UP(Other Functions)
T.CAL
Temperature
Calibration
H.CAL
Fatal Damage
୻
with Incorrect Calibration
Calibration
DODUP
High Alarm
DODUP
Abnomal
low Alarm
Be sure to read CAUTIONS. We do no recommend customers
to recalibrate by their own. If you need to recalibrate, please
ask purchase place.
WARNING
# Humidity
#Abnomal
Be sure to read CAUTIONS. We do no recommend customers
to recalibrate by their own. If you need to recalibrate, please
ask purchase place.
WARNING
Fatal Damage
୻
with Incorrect Calibration
Kljk
Whps
KlHuu
Alarm sounds when incubator temp. is higher than setting value
because of room temp. change or heating system disorder
* Setting Range : 0.0䮎 ~ 5.0䮎 (Default Setting : 2.0䮎)
Orz
Whps
OrHuu
Alarm sounds when incubator temp. is lower than setting value
because of room temp. change or heating system disorder
* Setting Range : 0.0䮎 ~ -5.0䮎 (Default Setting : -3.0䮎)
Selecting Centigrade (oC) and Fahrenheit (oF)
* Default Value : Centigrade (oC)
Xqlw
Oljkw#
LCD Backlight management setting
* Always On : Always BackLight On
* Always Off : Always BackLight Off
* Event On : 20 Sec. ON with Key input * Default Value : Always On
Vrxqg
ON/OFF Setting for Melody, other alarms
* Default Value : ON
##DOO#UHVHW
Factory setting
DOO#UHVHW
It returns to factory setting when you change the initial setting at discretion.
Lqir
Basic information of Incubator (versoin Indication)
Easy Function Operation
Function
୔ put some water after take off label from the back and attach to the window.
୔ If you want to change setting value, keep pressing "SET" button and change the value.
Krz#wr#Rshudwh
Sdjh
Select
the Species of Bird
Automatic Mode
Incubation
2 Sec.
Temp. Setting
Humid. Setting
Egg Turning Angle Setting
Egg Turning Interval Setting(Incubation day)
Other(Manual) Mode
Incubation
Select
the Species of Bird
How to change Setting
under Incubation
Once: Temp. Setting
4 times: Humidity Setting
7 times: Egg Turning Angle Setting
46
47

49
4;
9 times: Egg Turning Interval Setting
Incubation
Termination
Screen
on Incubation
Incubator Initialization
%*(*5"-*/$6#"503
Screen
on Incubation
5 Sec.
୅˩එ
"OFF"
UNDER 30%
Setting Value
Check
4:
4:
୅
එ
俎俯倘
How to change
Egg Turning Test
Select YES
"All Reset"
(Factory Setting)
How to turn off
Humidification Function
GIn case of low humidity
incubation
System finish
Are you sure?
4:
4;
4;
<
(1) How to Assemble the Incubator /
Egg-turning plate
2. Before use
How to Assemble
View Window
▶ Lock the four locking buttons
at the front and rear of the
incubator.
Back
Standard Tray
110V~120V
* Fit the water cap.
▶ Insert the power cord in the
socket at the back of the
main body.
Be careful when you assemble egg turning plate.
WATER
Water Cap
Gear
connecting part
Main Body-1
Egg-Turning Plate
81
'(
56
,'
(
Main Body-2
▶ If you do not assemble egg turning place correctly,
it can cuase incubator failure.
▶ Gear connecting part of egg turning plate must be
on the top side.
43
%*(*5"-*/$6#"503
(2) What is an incubation room? /
Preparation for Incubation
2. Before use
What's an Incubation Room? / Preparation for Incubation
The Incubation Room is a confined space for setting and operating an incubator.
Because the incubation room environment has a considerable effect on hatch rate, it's recommended to
control the environment for setting up an incubator; there should be little noise and vibration around and
temperature ranging 28℃(82.4℉) with small variation in temperature. Especially, if there are frequent occasions
when the temperature drops suddenly at night, compared with daytime, be sure to check from time to time
and pay attention so that the incubator is not directly exposed to s
unlight during daytime.
1
Insert the electric cord in the connecting jack
in the back of the main body and put the main plug into a socket.
The LCD display will light up and show temperature.
2
Open the watercap and fill the hole with DISTILLED WATER and refill water after about 5 min.
again up to the limit line on its inside mark.
(If you refill water during the incubation period, humidity goes down temporarily.)
After filling up with water, never shake or turn over the main body of the incubator, which would cause
water to spill inside the body and could cause a breakdown. Please close the water cap properly after fiilng.
During incubation period, check the DISTILLED WATER water levelabout every three days and refill water,
if necessary. (After you refill water, check again after 5min. and refill again.)
110V~120V
DISTILLED
WATER
WATE
R
OLPLW#Lqglfdwlrq
PULL OP
EN
In case you use the incubator without adding humidification water or intend to incubate eggs at low
humidity under RH 30%, you must stop its humidification function. please turn off the humidity unit if the
unit is empty water otherwise, humidity unit will be broke or you may not no longer use the unit.
(When using this function, the alarm for sensing water drop will go out.)
[See the description of humidification function OFF on Page 18]
※ How to turn off Humidification Function : Set humidity level at RH 30%.
%*(*5"-*/$6#"503
44
2. Before use
(2) What is an incubation room? /
Preparation for Incubation
Some gap (about 2mm) around the eggs is needed for easy egg turning as shown on the below. ▼
About 2mm
WAT ER
PULL OPEN
※ When you use the 'universal rolling divider' which is sold separately, be careful to adjust the distance of rolling
divider so that eggs do not roll out of position. Refer to the picture rignt side.
If you use Mineral water or Tap water for humidification,
the humidity unit can be broken easily because of water
scales. We strongly recommend you to use only
“DISTILLED WATER” for your machine, and
Autoelex Co.,Ltd & our distributors do not indemnify for
warranty service not only if you have any problem with
using mineral water, regular water, tab water and the like
but also if you had improper management or handling
for your machine. In this case, Autoelex Co.,Ltd. & our
distributors will charge for your after service.
WATE
R
ABS
Divider 10EA
<sold separately>
You can buy the ‘Distilled water’ in your local market,
and if you have any question, please contact the shop,
where you purchased your machine.
3
Place the eggs to incubate in the egg groove and
then close the view window.
Be careful to close the view window completely;
if not, the temperature and humidity will fail to go up.
WAT ER
The egg to incubate must be a fertilized egg.
(Refer to the guidebook.)
45
PULL OPEN
%*(*5"-*/$6#"503
(1) Incubation Modes /
Incubation start with Automatic Mode
3. Function Setting
Q Rcom Pro 50 incubator has two modes as automatic and manual mode,
and Rcom USB 50 incubator has three modes as automatic, manual,
and PC connecting mode.
Incubation Modes
Auto incubation
MANUAL button (Selection of birds)
ENTER button (Auto incubation starts after two seconds)
Temperature setting
ྙ Setting of temperature of
early and middle stages of incubation
ྚ Setting of temperature of final stage of incubation.
ྛ Setting of date of temperature change
in the final stage of incubation.
MENU button
OTHER (MANUAL) incubation
(Other birds)
Rcom PRO 50
Rcom USB 50
UP/DOWN button
(Selection of birds)
ྜ Setting of humidity of
early and middle stages of incubation.
ྜྷ Setting of humidity of final stage of incubation
ྞ Setting of date of humidity change
in the final stage of incubation.
Humidity setting
ENTER button
Egg turning angle setting
ྠ Setting of date of egg turning angle change
in the final stage of incubation.
MENU button
Incubation termination
(under incubation)
Egg turning interval setting
UP/DOWN button
("yes" selection)
ENTER button
(incubation termination)
--Fkrrvh#d#nlqg--
Fklfnhq
-#Fklfn#
-#Gxfn
-#Txdlo
-#Skhdvdqw
-#Shdirzo
-#Jrrvh
#######=
-#Rwkhu#Elugv
basic screen before
starting incubation
MENU screen
ྡ Setting of egg turning interval of
early and middle stages of incubation.
ྡྷ Setting of incubation date.
Incubation starts.
Fklfnhq
ྟ Setting of egg turning angle of
early and middle stages of incubation.
Rwkhu#Elugv
##93
<3䯍
Screen showing
incubation is in progress
##93
<3䯍
V|vwhp#ilqlvk
Duh#|rx#vxuhB
Screen showing incubation
of other birds is in progress
\HV
Screen showing
completion of incubation
Incubation start with Automatic Mode
The optimum incubation environment of the birds on the menu screen is memorized in the micro chip.
User can incubate easily using this function.
GH5FH
Duck
Quail
Pheasant
Peafowl
Chick
Goose
MANUAL
SHIFT
WildGoose
Others Birds
Turkey
Gold Pheasant
▶ Press MANUAL button to select species of birds in basic screen.
▶ Select species of birds and press ENTER button for about 2sec. then it starts incubation with automatic mode.
In auto incubation, user only needs to select type of birds as incubation environments such as optimum
temperature, humidity, egg turning, etc. are automatically controlled.
User can change incubation environments if needed.
Fklfnhq
Fklfnhq
%*(*5"-*/$6#"503
Vwduw
Lqfxedwlrq
2Sec.
####93
##<3䯍
46
3. Function Setting
(2) Incubation start
with Manual Mode
Incubation start with Manual Mode
This mode helps users to set temp. humidity, and egg turning etc. according to their needs.
This mode is ideal for those persons who are experienced in incubation.
▶ Press MENU button on basic screen.
MENU
▶ Select the species of birds with UP/DOWN button
and press ENTER button then it goes to incubation
conditions setting mode.
▶ Set required temp. humidity, and egg turning angle & interval
with UP/DOWN button, and press ENTER button to pass to
next step.
UP
#--###Fkrrvh##d###nlqg#####---###Fkrrvh##d###nlqg#####-Fklfnhq#
-#Fklfnhq#
-#Gxfn
-#Txdlo
-#Skhdvdqw
-#Shdirzo
-#Jrrvh
-#Zlogjrrvh#
If there is no proper option, please select option other
bird, Refer to Page16.
ྙ
DOWN
ENTER
* Press UP/DOWN button to select bird
species and press ENTER.
ྚ
Temperature setting
① Setting of temperature of
early and middle stages of incubation.
② Setting of temperature of
final stage of incubation.
③ Setting of date of temperature change
in the final stage of incubation.
▶ Optimum incubation temperature of general birds at early and
middle stages ① is 37.5℃, and the temperature of
final stage ② is better to set at 37℃ three days
before the expected date of hatching (D-Day) ③.
User can optionally change the temperature
of early, middle, and final stages of incubation.
(Default settings: ① 37.5℃, ② 37.0℃, ③ 3days)
5FNQFSBUVSF
䀺
䀻
䀼
%BZT
[Temperature Setting]
Humidity setting
④ Setting of humidity of
early and middle stages of incubation.
⑤ Setting of humidity of
final stage of incubation
⑥ Setting of date of humidity change
in the final stage of incubation.
▶ The optimum humidity depends on type of birds.
However the humidity of final stage ⑤
(3 days before incubation)is generally higher than that of
early and middle stages ④ of incubation.
(Default settings: ④ 45%, ⑤ 60%, ⑥ 3days)
It is recommended to raise the humidity setting to
over 60% from 1~3days before hatching.
(In areas of high ambient humidity, the humidity
may not need to be raised until the last half day after the chick is into the air space at the end of the egg.)
)VNJEJUZ
䀾
䀽
䀿
%BZT
[Humidity Setting]
Temperature and humidity is optimized when Rcom products are released.
We do no recommend customers to recalibrate by their own. If you need to recalibrate, please visit our
ZHEVLWHZZZUFRPFRNUĺ'RZQORDGĺ0DQXDORUDVNSXUFKDVHSODFH
Because of low price thermometers and hygrometers are not accurate, e recommend you to use special
calibrated thermo-hydrometer. (Poultry only thermo-hydrometer: check Rcom website: DigilogⅡ)
47
%*(*5"-*/$6#"503
(2) Incubation start
with Manual Mode
3. Function Setting
Egg-turning angle setting
⑦ Setting of egg turning angle of
early and middle stages of incubation.
⑧ Setting of date of egg turning angle change
in the final stage of incubation.
▶ The egg turning angle showing on LCD screen
may be different from the setting angle depending on
egg tray (based on standard egg tray) and
size of eggs. In general, the egg turning angle of
early and middle stages is 90° for chicken, golden pheasant,
pheasant. It is better to set higher angle (110 ~180°)
for bigger eggs and wild birds. It is a general
practice not to turn eggs (turn angle is 0°) at
final stage of incubation (3 days before expected hatching date).
5VSOJOH"OHMF
䁀
䁁
%BZT
[Egg Turning Angle Setting]
:KHQUQG5DQGRPLVVHWWKHHJJWXUQLQJDQJOHLVEHWZHHQaÛDWUDQGRP
(JJWXUQLQJDQJOHVHWWLQJUDQJHÛÛÛÛㆍㆍㆍㆍÛÛÛUQG
If having difference for the egg turning angle between display and actual operating,
Please find and select the proper angle.
Egg turning interval setting
⑨ Setting of egg turning interval of
early and middle stages of incubation.
⑩ Setting of incubation date.
5VSO*OUFSWBM
▶ It is a function to set the interval (time) of egg-turning ⑨.
It turns the eggs with the setting angle of early and
middle stages ⑦ every 60min.
User can optionally set the egg-turning interval ⑨ of eggs.
(Initial Setting: ⑨ 60min.)
䁂
"rnd"(Random) setting is for operating at random within
the limits from 10min. to 360min.
(JJWXUQLQJLQWHUYDOVHWWLQJUDQJHUQGㆍㆍㆍ
PLQ
䁃
[Egg Turning Interval, Incubation Date Setting]
▶ Setting of incubation date: The incubation date of birds on menu screen is a general incubation date.
User can input the correct incubation date.
(Initial settings: depending on type of birds)
※ Incubation date setting cannot be changed during incubation.
[ Setting Finish and Incubation Start ]
▶ After setting incubation date, press ENTER button to start incubation with melody.
5VSO*OUFSWBM
Fklfnhq
Vwduw
Lqfxedwlrq
##4k
<3ȋ
[Incubation Start Notification]
%*(*5"-*/$6#"503
[During Incubation]
48
(3) Incubation Start for
Other Birds
3. Function Settings
Incubation Start for other birds
This function is used when user wishes to incubate other birds
which are not memorized in the incubator menu setting.
User can change incubation conditions according to needs.
MENU
▶ Press MENU button in basic screen.
▶ Select Other Birds by UP/DOWM button and then press
ENTER to go to setting.
#--###Fkrrvh##d###nlqg#####---###Fkrrvh##d###nlqg#####--#J0Skhdvdqw#
-#Wxunh|
Rwkhu#Elugv#
-#Rwkhu#Elugv#
▶ Set incubation date, temperature, humidity, egg turning
angel and egg turning interval with UP/DOWM button,
and press ENTER button to save setting value.
[Refer to the page 14, 15]
䀽
䀿
DOWN
ENTER
* Press UP/DOWN button to select bird
species and press ENTER.
ྚ
%%BZ
䀺
䀻
ྙ
5FNQFSBUVSF
)VNJEJUZ
䀾
UP
%BZT
[Humidity Setting]
5VSOJOH"OHMF
䁀
䀼
%BZT
%BZT
[Temperature Setting]
OGYhh]b[X]gd`UmZcf8!8UmQ
ș How to Set Consecutive Incubation Function : On Incubation date
setting, raise incubation date up to D-50 and then press UP button
one more, then “?” will be show and it starts Consecutive incubation.
䁁
%BZT
[Egg Turning Angle Setting]
What is Consecutive Incubation Setting?
This function is used if you want to continue incubation without
termination with same setting.
5VSO*OUFSWBM
Vwduw
Lqfxedwlrq
䁂
##93
<3ȋ
%BZT
[Egg Turning Interval,
Incubation Date Setting]
49
[Incubation Start Notification]
[During Incubation]
%*(*5"-*/$6#"503
(4) Incubation start with PC connection Mode
,QFXEDWLRQ7HUPLQDWLRQ&KDQJH&HOV)DKU
Return to Factory Setting
3. Function Settings
Incubation start with PC connecting mode
<Rcom USB 50 MODEL ONLY>
With this function, you can share incubation process,
optimum incubation setting by building a database.
▶ Refer to the PC Software Manual for starting incubation
in PC connecting mode.
Incubation Termination
MENU
▶ During incubation, press MENU button then you can
see a message as "System finish, Are you sure?"
▶ Select YES with UP/DOWN button and press ENTER.
Fklfnhq
Fklfnhq
V|vwhp#ilqlvk
Duh#|rx#vxuhB
Ilqlvk
Lqfxedwlrq
##93
<3#䯍
Change Cels. & Fahr.
|•›
{Œ”—U|•›
{Œ”—Œ™ˆ›œ™ŒGœ•›
GGmˆ™Œ•Œ›OȋmP
s–žG
{Œ”—
s–l™™
|•›
Fklfnhq
Sdudphwhu#vdyhg
##93
<3#䯍
sŽ›
6HOHFWZLWK83'2:1EXWWRQ
6HOHFWÛ&RUÛ)ZLWK83'2:1EXWWRQ
Return to factory setting
▶ When users have changed the incubator settings,
but want to return to factory setting.
▶ Press SET UP button and select All Reset with
UP/DOWN button. Then, press ENTER.
If you press ENTER button once again, LCD display
goes off with message & alarm. Incubator returns to
factory setting after about 15 sec.
h““GyŒšŒ›
z–œ•‹
yŒšŒ›
yŒšŒ›
**
WARNING
**
GGGGGyŒ›œ™•G›–G
mˆŠ›–™ GšŒ››•ŽfG
h““G
yŒšŒ›
p•–
SET UP
BACK
Sdudphwhu#vdyhg
LCD
Display
goes off
Fklfnhq
Initialization after about 15sec.
%*(*5"-*/$6#"503
4:
(6) Incubation conditions reset /
How to Set Egg Turning Test /
Turn ON, OFF Humidification Function
3. Function Settings
Incubation Condition Reset during Incubation
▶ This is used when you want to change incubation
setting mode again during incubation.
Press MANUAL button during incubation, then
Temp. display will blink.
If you want to change Temp. reset with UP/DOWN button
and then press ENTER to save.
Using this method, you can also reset humidity, egg turning
angle, and egg turning interval. If you do not want to change
setting, just press MANUAL button then it passed to next stage.
Also, it returns to incubation screen if you do not press
any key for about 10sec.
MANUAL
SHIFT
▶ You can go directly to the needed setting mode by
pressing MANUAL button several times according to your needs.
It can be used when you want to check the current incubation
condition during incubation.
▶ If you press ENTER button, LCD display indicates
setting Temp. & Humidity.
Sdudphwhu#vdyhg
[Setting Save Message]
Egg Turning Test
▶ Press ENTER button for about 5sec. during incubation
period to check egg turning.
▶ If egg turning does not work, check whether you assembled
the egg turning plate properly.
[Refer to the page 10.]
ENTER
Humidification Function ON/ OFF Setting
▶ You should turn OFF humidification function when you operate incubator without water,
or when you want to incubate with low humidity below 30%.
▶ Press MANUAL button 4 times and then press DOWN button continuously until OFF indication is showing.
Then, press ENTER button to turn humidification off.
If you want to humidification turn ON, set humidity over 30%
)VNJEJUZ
Fklfnhq
Fklfnhq
Sdudphwhu#vdyhg
##93
<3#䯍
[Humidification ON]
4;
0''
4Times
0''
%BZT
5Times
##93
<3#䯍
[Humidification OFF]
%*(*5"-*/$6#"503
(1) Egg Turning Check / Alarm for water supplement /
Abnormal High or Low temperatue Alarm /
Power Failure Alarm Function
4. Other Functions
Egg Turning Check Function
▶ When starting egg turning, animation showed
on display with melody.
Water Shortage Detecting Function
▶ When water is short, humidification icon
is changed
Fklfnhq
Fklfnhq
and water supplement
##93
<3ȋ
alarm sounds after 5 min. This alarm continues
every 30 sec.
##93
<3ȋ
It takes about 1min. to return to normal display after
you refill water.
Fklfnhq
Fklfnhq
▶ When there is any problem on water detecting
sensor, humidification icon is changed like this
##93
<3ȋ
##93
<3ȋ
, and alarm sounds with message.
Abnormal High or Low Temperature Alarm Function
▶ When incubator temperature is different from
setting value, icon is changed
Fklfnhq
,
##93
<3ȋ
and display indicates current temp. and temp.
difference alternatively.
Fklfnhq
##93
<3ȋ
<Example>
※ Alarm call automatically turned off after 1min. but you
should press ENTER button to switch off alarm indication.
When temp. difference is 2੅, it indicates 39.5੅ and
+2.0 alternatively ( setting 37.5੅)
When temp. difference is -3੅, it indicates 34.5੅ and
-3.0 alternatively ( setting 37.5੅)
* How to Set Abnormal High Temp. Setting (When incubator temp. is higher than setting temp.) [Setting Range: 0 ~ 5੅, Default Setting : 2੅]
oŽGl™™–™
oŽG{Œ”—UGzŒ›
oUjhs
oŽG
{Œ”—
s–žG
{Œ”—
ol™™
s–l™™
Select with UP/DOWN button
oŽG{Œ”—UGl™™–™
GGG–Œ™GGGGGZUWȋjG
When MENU
screen is shown,
press SET UP/
BACK button
and display return
to basic screen.
Sdudphwhu#vdyhg
Set with UP/DOWN button
* How to Set Abnormal Low Temp. Setting (When incubator temp. is lower than setting temp.) [Setting Range: 0 ~ - 5੅, Default Setting : - 3੅]
s–žG
{Œ”—
ol™™
s–l™™
When MENU
screen is shown,
press SET UP/
BACK button
and display return
to basic screen.
s–žGl™™–™
s–žG{Œ”—UGzŒ›
oŽG
{Œ”—
s–žG{Œ”—UGl™™–™
GGGœ•‹Œ™GGT[UWȋjG
Sdudphwhu#vdyhg
|•›
Power Failure Alarm Function
▶ When you first switch on the power, or
in case of power failure during incubation,
Fklfnhq
display shows this icon
and incubator alarm sounds for about 10sec.
Press ENTER to remove.
%*(*5"-*/$6#"503
Fklfnhq
and incubator
##93
<3#䯍
4<
5. Incubation
(1) Humidity & Air Maintenance during Incubation /
Maintenance after Hatching
(2) Dew Condensation
Humidity & Air Maintenance During Incubation
▶ When hatching, humidity should be relatively high to prevent the
thin membrane from drying out or hardening before hatching.
▶ When hatching, it's recommended not to open the lid often.
This is because if you open the lid often humidity will be rapidly
decreased and it will take a long time to regain the proper humidity.
WATER
PULL OPEN
Incubator internal temperature is 37℃ (99.5℉) or more, and
hatching room temperature is below 28℃, in that case, RH70%
humidity is may not be able. The difference of ±5% humidity
value may occur from the humidity sensors difference, and there
are no problems at hatching
▶ It's very important to maintain humidity higher 1~3 days before
hatching than the early and middle incubation periods. Humidity
requirements during incubation are RH 45~55% for waterfowl,
RH 40~45% for poultry and RH 35~45% for parrot, in general.
One day before hatching, all kinds of birds need about RH 65%
humidity and sometimes need higher than that.
However, in areas of high ambient humidity, lower levels of
humidity may be needed during incubation.
WATER
PULL OPEN
When the baby chickens hatch out,
please move them into a brooder.
It's very important to keep humidity higher than RH 60%
before hatching 3days.
※ Air Controlling Lever : Outer fresh air can be flowed into incubator
inside without affecting insulation. When eggs start hatching,
open air controlling lever either fully or half-open.
7@CG9
CD9B
Air Vent
Maintenance after Hatching
▶ It is necessary to use a brooder for baby chicken or bird since they are too week against cold or cool environment.
If you try egg-hatching in your incubator, there would be lots of germs, feathers, which causes of low egg hatching
possibility for your next hatching. Also, they can make your incubator broken or faulty.
We strongly recommend you to use independent Hatcher or Brooder for egg-hatching.
If you have any faulty or broken because of not using independent Hatcher or Brooder, we do not serve you the
free warranty service. In other words, you have to pay for the service charge.
To make a simple Hatcher or Brooder, please refer to the our web-site (www.Rcom.co.kr).
Please do not try to egg-hatching in the incubator. It makes your incubator broken or faulty, and we do not
give you free warranty service. (Please move all the eggs 1~3 days before hatching into Hatcher or Brooder.)
Hatcher : The machine for egg-hatching. Operate it 1~3 days before egg-hatching. (Rcom MARU H&B)
Brooder : The machine makes baby chickens or birds warm up against cold or cool environment. You can
set up proper temperature and humidity. (Rcom MARU H&B / Rcom Brooder Series)
▶ As there is some difference in chick feed for each kind of bird, so it's desirable to obtain useful information
about the chicks before hatching.
Be sure to use a three-wavelength 20W bulb. If you use a bulb over 20W. temperature goes up, possibly
killing the chick or causing a fire. If there is too much water and a chick would falls into water, its feathers
get wet and it can be died of loss of body heat. Here, dry feathers with a hairdryer. etc
Be sure to use a three-wavelength 20W bulb :
In case breeding room size 370(mm) x 270(mm) x 130(mm)
Dew Condensation
This is a naturally occurring phenomenon when there is a
significant difference in temperature between inside and
outside of the incubator during incubation period. If this occurs,
water may form in inside bottom of the main body of the
incubator(bottom part).
53
%*(*5"-*/$6#"503
6. How to Clean
(1) How to Disassemble
▶ Pull out the electric cord from the connecting jack and
also take out the plug from the outlet.
Don't turn off the power soon after using the incubator,
as this may cause a break down due to moisture left
inside the main controller. At this time, it's better to
firstly remove the water inside of the incubator and dry
by operating it for 1hour and then turn it off or open the
view window and dry it naturally for 2~3 hours and,
then, re-operate it, which may lengthen the life time of
incubator.
(Set humidification function OFF. / Refer to the page 18.)
110V~120V
How to disassemble and clean the incubator
1
Unlock and remove the locking buttons for
four parts at the front and back of incubator
by pulling them forward.
110V~120V
back
2
The bottom part of incubator should be thoroughly cleaned
with water and dried. The upper part should be naturally dried
in the well-ventilated place for about one day to remove
moisture left inside of the incubator after hatching thoroughly.
Don't clean the product with organic solvents such as
benzene, thinner, etc. which may cause deformation or
decoloration of the plastic parts.
3
▶ When using humidification function, a lot of alien matter
sticks to the humidification heating element ⓐ. This may not
cause failure, but when terminating incubation please clean
the humidifying heater lightly with a soft brush.
9L
C9@
5IH
▶ If you place the main body(upper part) on the floor,
please don't let the humidification heating part touch with the
floor.
9L
C9@
5IH
9L
C9@
5IH
If you inflict impact on the humidification heating part or
scrape it with a sharp instrument, the humidifying heater
will be damaged.
We kindly recommend you to use distilled water
In order to reduce a foreign substance on the
humidifying heater device.
%*(*5"-*/$6#"503
೛
5IHC9@9L
54
6. How to Clean
(2) How to Clean
4
Start the vacuum cleaner to remove the dust as shown on the
right and thoroughly shake out the minute dust with a fine brush.
If the incubator goes through incubations several times,
feather, dust, shell, etc. accumulate inside the main body,
which may cause a break down, so be sure to clean
the product before storage.
In case the incubator clean status is poor which may cause fan noisy or stopping.
Cleaning
the fan
9L
C9@
5IH
9L
C9@
5IH
9L
C9@
5IH
9L
C9@
5IH
5IHC9@9L
5
If you finish cleaning the incubator, reassemble it in the reverse
order of disassembly. Wipe out outside the main body with a
wet cloth and dry it in a cool and well-ventilated place before
storage.
WAT ER
[Refer to How to assemble on Page 10.]
Don't clean the product with organic solvents such as
benzene, thinner, etc. which may cause deformation or
decoloration.
55
PULL OPEN
%*(*5"-*/$6#"503
7. Product Information
(1) Servicing /
Frequently Asked Questions (FAQ)
Servicing
All our Rcom digital incubators of Autoelex Co., Ltd. are made by precision systems under strict quality
control. But occasionally some defective products are found on the way of their distribution.
If any problem occurs, then please contact Rcom service center or distributorsin your country.
We will do our best to solve the problems, if any, for you. This product is designed in modular mode, so
for its repair, if any, a qualified person can replace the part concerned with ease.
* Complaint Department : 82-55-337-2560
*E-mail Receipt : Rcom@Rcom.co.kr
Frequently Asked Questions (FAQ)
Troubles
Expected Causes (Possibility)
Countermeasures
In case hatching rate
is low
ઔWhen the egg is an unfertilized egg.
ઔGetting infected by germs
ઔWrong incubation setting
ઔHealth condition of mother bird
ઔImproper egg turning
ઔ Inspect the egg to check possibility
of egg surviving.
ઔ Disinfect the incubator.
ઔ Check all settings of incubator.
Especially, check them focusing
on the temperature.
ઔ Review care of health of mother bird.
ઔ Check if egg turning is normal.
When a chick hatches
out earlier than expected
or a deformed chick
hatches out
ઔSetting temperature high
ઔEgg turning was not operating normally
ઔ Lower temp. setting of the
incubator about 0.5੅(1એ)
ex) 37.5℃ (99.5℉) ĺ 37.0℃ (98.6℉)
ઔ Check if egg turning function is OFF
When a chick hatches
out later than
expected
ઔSetting temperature low
ઔ Raise temp. setting of the
incubator about 0.5੅(1એ)
ઔ ex) 37.0℃ (98.6℉) ĺ 37.5℃ (99.5℉)
When hatching dates
are so different from
each egg (When all
chicks don't hatch out at
the same time but over a
long period)
ઔ Eggs stored for different lengths of time
ઔ Diffferent incubation temperatures
ઔ Minimize the time to store egg properly.
ઔ Check Temperature difference
in the incubator.
(sunlight, temp of incubation room, etc.)
When intending to
hatching various eggs
at the same time
ઔ Incubation days are different,
so hatching rate falls down.
ઔ Eggs might be contaminated by chicks
that hatched first.
ઔ Mark hatching date on eggs and
move them to other incubator
(brooder) just on the marked date.
ઔ In case of putting in many eggs
at the same time, it's convenient
to prepare a spare incubator available
as a brooder
%*(*5"-*/$6#"503
56
7. Product Information
Troubleshooting
CIRCUMSTANCE
(2) Troubleshooting
If you need detail self diagnosis,
please click “self diagnosis” on our website.
ITEMS TO BE CONFIRMED
SOLUTIONS
No signs of power
to the incubator.
ઔ Check electric cord is properly connected.
ઔ Check if there is a power outage.
ઔ Check whether the plug is damaged.
ઔ Connect the cord again.
ઔ Check the main socket with any other
electric appliances.
ઔ Try to insert to another outlet.
Temperature will
not go high enough.
ઔ Check your setting temperature.
ઔ Check the air circulation FAN is working.
ઔ Initialize the incubator.
[Refer to the page 17]
ઔ Set the temperature as required.
Alarm sounds with
HI indication
䯝 Check if room temperature is too high
䯝 Check if incubator is exposed to the direct
rays of sun
䯝 Adjust room temperature 28℃ (82.4℉)
䯝 Install incubator without the direct rays of sun
䯝 Return incubator to factory setting [Refer to page 17]
(abnormal high temp.)
Alarm sounds with
LO indication
(abnormal low temp.)
ઔ Take the power plug out of the outlet, and
disassemble the main body for cleaning
around the air circulation fan with brush.
䯝 Adjust room temperature 28℃ (82.4℉)
䯝 Check if room temperature is too low
䯝 Check if incubator heater(temperature controlling- 䯝 Place thermometer inside of incubator and check
system) is normally working
if setting temperature is correct
䯝 Return incubator to factory setting [Refer to page 17]
Humidity will not
go high enough.
ઔ Check your setting humidity.
ઔ Close the view window again after checking.
ઔ Initialize the incubator. [Refer to the page 9]
ઔ Supply water.
ઔ Set the humidity again as required.
The machine makes
some noise.
ઔ Check if there is any hatching debris such as
feather or eggs-shell in the incubator FAN.
ઔ Take out the plug out of the outlet and
disassemble the main body and clean
around the air circulation fan with brush.
Egg-Turning fails
to work.
ઔ Check that the Egg-turning stoppage is not
activated. (Egg-turning lamp lighting)
ઔ Check that there are no foreign items on the
egg turning tray.
ઔ Check if egg turning plate is assembled correctly.
[Refer to the page 10]
ઔ If you need to turn the eggs, you can
manually re-start egg-turning.
ઔ Unplug the power supply and
disassemble the main body for cleaning
the egg turning tray and gear.
ઔ Assemble egg turning plate as the picture on page 10.
Dew foams in
the incubator.
ઔ Check the incubator is not placed
too cold circumstances.
ઔ When you turn OFF incubator and then
turn on.
ઔ Move the incubator to where the ambient air
temperature is over 28℃ (82.4℉)
ઔ Check that you have not overfilled the incubator.
ઔ Check that the incubator placed on inclined
surface.
ઔ Check if it is Dew condensation
ઔ Do not fill water over LIMIT indication.
ઔ Place incubator under a level surface.
- It is normal that the machine
emits some sounds because
it uses air circulation fan
for working.
Water leaks from
the machine.
ઔ Dew condensation is normal.
ઔ Dry the incubator completely under well ventilated place.
Be sure that the incubator works without any problem before placing eggs in the incubator.
57
%*(*5"-*/$6#"503
7. Product Information
(3) Specification
1-1 Name : Rcom USB 50 / Rcom PRO 50
1-2 Model : UX-50 / PX-50
1-3 Supporting Soft : Rcom USB 50
INCUBATION SYSTEM (WINDOWS)
Specification
Specification
Power
AC 100~120[V], 50/60[Hz] / 220~240[V], 50/60[Hz]
Working Temp.
20 ~ 42.0[ C]
30 ~ 70[%]
o
Working Humid.
Power Consumption
Capacity
Average. 65[W]
24 ~ 116[EA]
Weight
6.65 [Kg]
Size
(W)633 * (L)523 * (H)171 [mm]
Automatic
250[V] 2.0[A] (Ø5×20[mm])
automatic setting for each birds (manual control available)
Manual
20.0 ~ 42.0[ C]
PROG (PC)
normal temperature ~ 45.0[ C]
Automatic
Automatic setting for each birds (manual control available)
Manual
30~70[%] (It can be changed according to the conditions)
PROG (PC)
30~70[%] (It can be changed according to the conditions)
Fuse Standard
Temp. Limits
Humid. Limits
Egg-Turning Interval
o
o
o
15[ ]~ Different from the egg tray
Small
- 116 [EA] (Quail egg size) - Small egg tray
Standard - 48 [EA] (Chick egg size) - Standard egg tray
Large
- 24 [EA] (Goose egg size) - Large egg tray
For all size egg - Different from the species of egg
Universal tray (option)
Capacity
PC Connecting
- USB MODEL -
MAX. 120[W]
USB 2.0
- Real - time hatching condition transmission and setting control
- Incubator Upgrade
You will be asking for service charge if you are in below cases.
1. Broken or Problem caused by ‘No cleaning’ or ‘Improper handling’
2. Broken or problem caused by ‘Not using distilled water’
3. Broken or problem caused by ‘Trying Bird hatching in incubator’
(Please don’t try bird hatching in incubator. Please use Hatcher during bird hatching.)
4. Broken or problem caused by ‘Wrong controling(Using)’
5. Broken or Problem caused by using the machine out of User’s Manual.
6. Broken or problem caused by ‘Customer’s mistake or fault’
Ě Register your product Serial No. on our website for free 2 years gurantee.
Ě Refer to website for how to register. (Free 1 years gurantee in case not registerd.)
※ Product Registration Procedures
If you are a new member of Rcom, you need to log in our website at www.Rcom.co.kr
1. Click “SIGN UP” on top of the right corner.
2. Fill out the information on the blanks.
If you already registered your information on the Rcom website, please log in to
www.Rcom.co.kr.
1. Click “Login” on top of the right corner.
2. Select “Customer” and click “Register Products”.
3. Fill out the information on the blanks.
You will need below information to register on our website.
1. Your name
2. Your (home/company) address & Email address, country
3. Your product(model) name & Serial number
4. Date of purchase & Name of purchased shop you bought from
%*(*5"-*/$6#"503
58
Rcom USB 50, PRO 50, MAX 50 PART LIST
Image
P a rt N o
Names of goods
(*.Compatible)
H50-H601-10
H50 Body
H50-A601UL-10
H50 USB Body
110ASM/
H50 USB Body
220ASM/
H50 PRO Body
110ASM/
H50 PRO Body
220ASM/
H50 MAX Body
110ASM/
H50 MAX Body
220ASM/
H50-A601UH-10
H50-A601PL-10
H50-A601PH-10
H50-A601ML-10
H50-A601MH-10
H50-A602-10
H50-H606-10
H50-A605L-10
H50-A605H-10
H50-AH604-10
Image
P a rt N o
Names of goods
(*.Compatible)
H50-A641-10
H50 SMPS
PCB ASM
RCM-A31-10
TH V2 Sensor
ASM
H50-H618-10
H50 Main PCB
Cover
H50-H611-10
H50 Humi
Heater Cover
H50-A610-10
H50 Humidity
Unit ASM
RCM-700-10
Silicon Tube
K20- H512-10
Heat Support -A
H50-H612-10
Heat Support- B
H50 Bottom ASM
H50 Slider
H50 Heater Frame
110ASM
H50 Heater Frame
220ASM
50Window ASM
H50-A604P-10
H50 PRO Main
PCB ASM
H50-A630L-10
H50 Silicon 110
HEATER ASM
H50-A604U-10
H50 USB Main
PCB ASM
H50-A630H-10
H50 Silicon 220
HEATER ASM
H50-A604M-10
H50 MAX MAIN
PCB ASM
H50-AH613-10
H50 Body Lock
ASM
੔ Partly spare parts are not on the parts list.
Rcom USB 50, PRO 50, MAX 50 PART LIST
Image
P a rt N o
Names of goods
(*.Compatible)
H50-H691-10
H50 Slider Roller
H50-H616-10
H50-H608-10
(Option)
H50-H622-10
RCM-H623-10
H50-H624 -10
(Option)
H50-H810-10
H50-H607-10
H50-H620-10
Image
P a rt N o
Names of goods
(*.Compatible)
H50-H621-10
H50 Small Tray
H50-H606M-10
H50 MAX
Membrane SW
H50-A606P-10
H50 PRO
Membrane SW
H20-F224-10
H20 Pinion Gear
H20-F223-10
330 Geard
Motor
H20-F214-10
Humi BLDC
FAN40
H20-F226-10
BLDC FAN50
H20-304EU-10
Power Coard(8)
H20-H686-10
H20 Rubber Foot
H50-F244-10
(Option)
H50 Ha tching
Pad
RCM-347-10
USB Cable
H50 50Water Cap
H50 Brooding
Tray
(*For reptile
incubator)
H50 Universal
Tray
ABS Divider(3호)
H50 Roller Divide
O-Ring(50용)
H50 Standard
Tray
H50 Large Tray
੔ Partly spare parts are not on the parts list.
3DPNJTEFTJHOFEGPSVTFSTFBTZBOEDPOWFOJFOUVTF
*UDBOCFDIBOHFEXJUIPVUOPUJDFGPSJNQSPWFNFOUJOQFSGPSNBODF
EFTJHOUSFBUNFOUBOETPGUXBSFFUD
www.Rcom.co.kr
SELLER
MANUFACTURER
ú)FBE0GGJDF%FPLBN+VDIPO(JNIBF
,03&"
ú5&%JSFDUUPTBMFTUFBN
_0GGJDF
ú'"9
ú&."*3DPN!3DPNDPLS
3DPNJTUIF#FTU%FTJHOXJUI)JHI2VBMJUZ7BMVFBOE1FSGPSNBODF