MaxIT | Classic | User manual | MaxIT Classic User manual

(((
)
MaxIT ))
BLUE Dongle User Manual
MaxIT® BLUE features
Multi-function
Button (“MFB”)
3.5mm stereo
jack plug
Reset button
Charging socket
3
4
1) Introduction
Your MaxIT®BLUE Dongle is a lightweight device utilising
Bluetooth® wireless technology.
When used in conjunction with the MaxIT ® Pulse Wireless
Loopset Model # MA007S, it allows the hearing aid wearer
to listen to audio output from devices such as MP3 players,
PCs, televisions etc.
Power is provided by an internal re-chargeable battery.
PLEASE NOTE: The MaxIT® BLUE Dongle is NOT
backwardly compatible with the earlier model MaxIT ®
Classic Wireless Loopset Model #s BH015 or MA007M as
these do not support the A2DP profile.
5
2) Package contents
MaxIT® BLUE Dongle
3.5mm stereo jack plug connector
USB Charger cable
User guide
3) Charging the re-chargeable battery
a)
Connect the USB charger cable to the BLUE Dongle
Charging Socket, plug the charger cable into a USB
port on your computer and ensure that the computer
is turned on.
6
b)
Whilst the battery is charging the MFB light will
glow RED. When the battery is fully charged the
MFB light will fade and go out.
c)
Initial charging of the battery will take around 3
hours.
d)
The BLUE
charging
Dongle can be used during battery
IMPORTANT:
Ensure that the battery is fully charged prior to
initial use otherwise the battery life may be
reduced.
7
4) Initial pairing and connection procedure
a)
To use the BLUE whilst charging, pair the unit 1st
then connect the charging cable.
b)
Press and hold the Multifunction Button (“MFB”)
until the LED flashes alternately between BLUE and
RED indicating that the BLUE Dongle is in pairing
mode.
c)
Press and hold the TALK button on your MaxIT ®
Pulse Wireless Loopset for approximately 7 seconds
until the LED flashes alternately between YELLOW
and RED indicating that the Loopset is in pairing
mode.
8
d)
The 2 units will pair automatically. This will be
indicated by the LED on the BLUE Dongle flashing
BLUE rapidly 5 times accompanied by a single beep
in the hearing aid.
e)
If pairing does not occur as expected, turn off both
the BLUE Dongle and the Pulse Loopset, wait for 10
seconds and then repeat steps a to d above.
f)
Once pairing is complete, connect the BLUE Dongle
to the desired audio output equipment using the
3.5mm stereo jack plug connector.
5) Subsequent connection procedure
a)
Press the BLUE Dongle MFB for 2 seconds until the
LED flashes BLUE and then release.
9
b)
The BLUE Dongle will connect automatically to the
Pulse Loopset. If the BLUE Dongle cannot find the
Pulse Loopset within 2 minutes, it will turn off
automatically as part of the power saving mode (see
paragraph 7).
6) Switching OFF the BLUE Dongle
To switch OFF your BLUE Dongle, press and hold the
MFB for 3 seconds until the LED illuminates RED for 1
second. Release the button and your BLUE Dongle will
then switch off.
7) Power saving mode
If your BLUE Dongle is out of range of your Pulse Loopset
for more than 2 minutes, your BLUE Dongle will enter
power saving mode and turn off automatically to conserve
battery power. To re-establish connection, return within
10
range of your BLUE Dongle and press the MFB for 2
seconds until the LED flashes BLUE and then release.
8) Low battery alert
When the BLUE Dongle is switched on and battery power
is low, the LED will flash RED every 5 seconds.
MaxIT® BLUE Dongle specifications
Bluetooth® wireless technology Version 1.2 Class II
A2DP profile supported
Frequency 2.4GHz spectrum
Maximum range 10 metres
Weight 16.5g
11
Continuous operation of up to 7 hours
(((
)
MaxIT ))
SOLUTIONS FOR THE HARD OF HEARING
Contact Information
MaxIT Limited
Tel/Fax:
Email:
+852 31436962
enquiry@maxit.com.hk
12
Website:
www.maxit.com.hk
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by MaxIT Ltd. is under license.
13
Download PDF

advertising