Moffat TURBOFAN E31D4 Specifications

30DSERIES
E31D4
(Digital Operation)
Installation and Operation Manual
234144-9
MANUFACTURED BY
Moffat Limited
Christchurch
New Zealand
INTERNATIONAL CONTACTS
AUSTRALIA
Moffat Pty Limited
Web:
E.Mail:
Main Office:
Service:
Spares:
Customer Service:
www.moffat.com.au
vsales@moffat.com.au
(tel) +61 (03) 9518 3888
(fax) +61 (03) 9518 3833
(tel): 1800 622 216
(tel): 1800 337 963
(tel): 1800 335 315
(fax): 1800 350 281
CANADA
Serve Canada
Web:
E.Mail:
Sales:
Service:
www.servecanada.com
info@servecanada.com
(tel): 800 551 8795 (Toll Free)
(tel): 800 263 1455 (Toll Free)
NEW ZEALAND
Moffat Limited
Web:
E.Mail:
Main Office:
www.moffat.co.nz
sales@moffat.co.nz
(tel): 0800 663328
UNITED KINGDOM
Blue Seal
Web:
E.Mail:
Sales:
Spares:
Service:
www.blue-seal.co.uk
sales@blue-seal.co.uk
(tel): +44 121 327 5575
(fax): +44 121 327 9711
(tel): +44 121 322 6640
(fax): +44 121 327 9201
(tel): +44 121 322 6644
(fax): +44 121 327 6257
UNITED STATES
Moffat
Web:
Sales:
Service:
www.moffat.com
(tel): 800 551 8795 (Toll Free)
(tel): +1 336 661 1556
(fax): +1 336 661 9546
(tel): 800 858 4477 (Toll Free)
(tel): +1 336 661 1556
(fax): +1 336 661 1660
REST OF WORLD
Moffat Limited
Web:
E.Mail:
www.moffat.co.nz
export@moffat.co.nz
The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in writing
by the manufacturer.
In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and design
without prior notice.
© Copyright Moffat Ltd. July 2012.
Contents List
E31 Turbofan Convection Oven.
Model Numbers Covered in this Manual
E31D4 - Turbofan Oven - 4 Tray Convection Oven.
Introduction ........................................................................................................... 2
Safety Information
Specifications ......................................................................................................... 3
Installation ............................................................................................................. 4
Installation Requirements
Unpacking
Location
Clearances
Stand Mounted Ovens
Electrical Connection
Positioning and Levelling of Oven
Initial Start-Up
Commissioning
Operation ................................................................................................................ 6
Operation Guide
Oven Control Panel
Using the Oven - Manual Mode
Cooking in Program Mode
Setting the Oven Programs
Operator Accessible Parameters .......................................................................... 10
Setting the Operator Accessible Parameters
Table of Operator Accessible Parameters
Cleaning and Maintenance ................................................................................... 11
Cleaning Guidelines
Oven Cleaning
Periodic Maintenance
Fault Finding ......................................................................................................... 13
Electrical Schematics ............................................................................................ 14
Replacement Parts List......................................................................................... 15
Appendix 1 - Reversing the Oven Door ................................................................ 16
Introduction
Before using your new oven, please read this instruction
manual carefully, pay particular attention to any information
labelled ‘WARNING’, ‘CAUTION’, ‘IMPORTANT’ or
‘NOTE’ in this manual.
Warning
Indicates a hazardous situation
which, if not avoided, will result in
death or serious injury.
Caution
Indicates a hazardous situation
which, if not avoided, will result in
minor or moderate injury.
This manual must be kept by the owner for future
reference.
A record of the Date of Purchase, Date of Installation
and Serial Number of the oven should be recorded in
the area provided below.
The serial number of this oven can be found on the
Technical Data Plate located on the front right hand
side panel, see diagram in ‘Installation Section’.
Model Number:
Serial Number:
If you are unsure of any aspect of the installation,
instructions or performance of your oven, contact your
TURBOFAN dealer promptly. In many cases a phone call
could answer your question.
Dealer:
Service Provider:
Should you contact your TURBOFAN dealer on any matter
concerning this oven, please have the information provided
opposite, readily available.
Date Purchased:
Date Installed:
Safety Information
For your safety, please pay attention to the following symbols
marked on the appliance.
- Risk of electric shock.
No user serviceable parts inside.
Qualified service person access only.
Disconnect from power before servicing.
2
Specifications
E31D4
Oven Power Ratings
208V,
1P+N+E,
50/60HZ,
2.9 kW
220V,
1P+N+E,
50/60HZ,
3.1 kW
230-240V,
1P+N+E,
50/60HZ,
3.1 kW
Oven Tray Details
Tray Capacity
Tray Spacing
4 x GN 1/1 Pan
4 x US ½ Pan
80 mm / 3⅛”
3
Installation
Installation Requirements
Important:
•
Installation shall comply with local electrical, health and safety requirements.
•
It is most important that this oven is installed correctly and that oven operation is correct before use.
•
If you have any questions regarding the proper installation and / or operation of this oven, please contact your local
Turbofan distributor.
Unpacking
Clearances
1. Remove all packaging and transit protection including
all protective plastic coating from the exterior stainless
steel panels.
2. Check the oven and supplied parts for damage. Report
any damage immediately to the carrier and distributor.
3. Check that the following parts have been supplied with
your oven:4 x Leg Adjustable.
To ensure correct ventilation for the motor and controls,
the following minimum installation clearances are to be
adhered to:Rear
75 mm / 3”.
Left-hand side
75 mm / 3”.
Right-hand side
75 mm / 3”.
CLEARANCE FROM SOURCE OF HEAT.
A minimum distance of 300mm (12”) from the
appliance sides is required.
4. Report any deficiencies to the distributor who supplied
your oven.
5. Securely fit the 4 legs supplied with the oven.
6. Check that the available electrical supply is correct to
that shown on the Technical Data Plate located on the
front right hand side panel.
•
Important:
The vent located at the rear of the oven must NOT be
obstructed.
Oven Vent Location
Refer to ‘Specifications’ section, ‘Oven
Specifications Tables’.
Location
1. Position the oven in its approximate working position.
2. The unit should be positioned so that the control panel
and oven shelves are easily reachable for loading and
unloading.
Stand Mounted Ovens
For ovens that are to be mounted to a stand, the oven feet
are used to level the oven on the stand. Refer to the
instructions supplied with separately ordered stands for
mounting details.
Technical Data Plate - Location
4
Installation
Electrical Connection
Warning
This oven must be earthed / grounded.
If the supply cord is damaged, it must be replaced by a
suitably qualified person in order to avoid a hazard.
Each oven should be connected to an adequately protected
power supply and an isolation switch mounted adjacent to,
but not behind the oven and must be readily accessible to
the operator. This switch must be clearly marked and
readily accessible in case of fire.
Check the electricity supply is correct to as shown on the
Technical Data Plate on the front right hand corner of the
oven side panel.
Ensure that the oven is fitted with the appropriate power
cord and plug.
Positioning and Levelling of Oven
1. Correctly locate the oven into its final operating position
and using a spirit level, adjust the oven feet so that the
oven is level and at the correct height.
Initial Start-Up
Before using the new oven;
1. For first time use of the oven, operate the oven for
about 1 hour at 200°C / 400°F to remove any fumes or
odours which may be present.
2. Please refer to the Operation Section of this manual for
details on how to correctly operate and shutdown the
oven.
Commissioning
Before leaving the new installation;
Check the oven functions in accordance with the
operating instructions specified in the ‘Operation’
section of this manual.
Ensure that the operator has been instructed in the areas
of correct operation and shutdown procedure for the
appliance.
NOTE: If for some reason it is not possible to get the
appliance to operate correctly, turn off the
power supply at the mains supply and contact
the supplier of this appliance.
5
Operation
Operation Guide
Warning
Warning
Take care when opening the oven door
during baking. Let hot air and steam escape
before removing or replacing food as the
steam produced can cause steam burns.
Some parts of this oven will become VERY
HOT during use and could cause burns if
touched.
•
Turbofan Ovens have been designed to provide simple operation.
•
This oven is intended for use in a commercial kitchen and must only be put to the use for which it was intended, i.e.
cooking food product. To use this oven correctly please read the following sections carefully:-
Oven Control Panel
Temperature Display - Shows the
Programming Button and LED -
preset chamber temperature.
When used with ‘Temperature’ Button,
shows actual oven temperature for 5
seconds.
Shows Cooking Modes and Error
Codes.
Used to enter the ‘Programming’
mode.
Temperature Button and LED Shows actual oven temperature for 5
seconds on the Temperature Display.
LED ‘On’ when heating; LED flashes
when showing actual temperature.
Grill / Broil Button and LED Switches between ‘Baking Mode’ and
‘Grill / Broil Mode’.
Temperature Adjustment Control.
Time Display - Shows cook time in full
minutes only from 180 - 1, and
seconds for final minute only.
Light On / Off Button and LED Turns oven light ‘On / Off’.
On / Off / Stand-By Button and
LED - Press ‘On / Off’ Button once to
Start / Stop Button and LED Pressing the ‘Start / Stop’ Button oven
switches between ‘Time Start’ and
‘Temporary Pause’ Modes. LED will
flash when timer is paused.
When in the cooking cycle, pressing
the ‘Start / Stop’ Button for 2 seconds
will end the cooking cycle.
turn the oven ‘On’.
Press and hold ‘On / Off’ Button for 2
seconds to turn the oven ‘Off’.
Time Adjustment Control.
6
Operation
Using the Oven - Manual Mode
1.
To check actual oven temperature
during preheat or cooking, press
‘Temperature’ button.
Actual
temperature will display briefly on
‘Temperature Display’ before the
display reverts to the pre-set
temperature.
TURN ‘ON’.
Press ‘On-Off’ button.
Temperature Dislay.
Temperature Display will show actual temperature.
2.
Heating ‘On’
Indicator
SET TEMPERATURE.
+ to increase the temperature.
- to decrease the temperature.
At any time during cooking, time
and temperature can be adjusted
by using the ‘Time’ / ‘Temperature’
controls.
Time Display.
Time Display will show actual time set.
Timer ‘On’
Indicator
Power ‘On’
Indicator
3.
This oven can be used without
using the ‘Timer’, as it is purely a
timer and does not control the
baking operation of the oven.
SET TIME.
+ to increase the time.
- to decrease the time.
4.
If the ‘Timer’ is set to the ‘Infinity’
setting
, the timer will count
elapsed time to a maximum of 999
minutes.
START TIMER.
Press ‘Start / Stop’ button to start timer operation.
Opening the oven door during a
cooking cycle will pause the
cooking time.
To continue
cooking, close the oven door.
- Press any button, to cancel the ‘Alarm’.
- Press ‘Grill / Broil’ button, to select the Grill / Broil mode.
- Press ‘Act Temp’ button, to check ‘Actual’ temperature of oven at any time during cooking.
- Press ‘Light’ button, to turn ‘On’ oven light. (refer - ‘Operator Accessible Parameters’).
- Press ‘Program’ button, to program the Oven refer to the ‘Installation and Operation Manual’.
- Press and hold ‘On / Off’ button, for 3 seconds to turn ‘Off’ the Oven.
Grill / Broil; - Grill / Broil function can be selected at any time during the Manual Mode by pressing the ‘Grill / Broil’ button.
The ‘Grill / Broil’ LED will illuminate.
The Time Display will show either ‘Grill’
or ‘Broil’
.
On completion of the Grill / Broil mode, the oven temperature will return to the temperature previously set.
7
Operation
Cooking in Program Mode
1.
TURN ‘ON’.
Press ‘On-Off’ button.
Press ‘Programs’ button.
Program Mode
Indicator
Heating ‘On’
Indicator
Temperature Dislay.
Temperature Display will
show program selected.
2.
To check actual oven temperature
during preheat or cooking, press
‘Temperature’ button.
Actual
temperature will display briefly on
‘Temperature Display’ before the
display reverts to the pre-set
temperature.
SELECT A PROGRAM.
+ to scroll forward through programs.
- to scroll backward through programs.
Light will remain ‘On’ by default
when cooking in ‘Program’ mode.
Time Display.
Time Display will show ‘Pre-Heating’.
Program cannot be started until
pre-heating is completed.
When cooking in ‘Program’ mode,
the oven light will remain ‘On’ until
cooking is completed.
Load Oven.
‘Time’ display will show
‘Ready’.
3.
Opening the oven door during a
cooking cycle will pause the
cooking time.
To continue
cooking, close the oven door.
START PROGRAM.
Press ‘Start / Stop’ button to start
cooking program.
- Press any button, to cancel the ‘Alarm’.
- Press ‘Grill / Broil’ button, to select the Grill / Broil mode.
- Press ‘Act Temp’ button, to check ‘Actual’ temperature of oven at any time during cooking.
- Press ‘Program’ button, to program the Oven refer to ‘Setting the Oven Programs’ overleaf.
- Press and hold ‘On / Off’ button, for 3 seconds to turn ‘Off’ the Oven.
Grill / Broil; - Grill / Broil function can be selected at any time during the Program Mode by pressing the ‘Grill / Broil’ button.
The ‘Grill / Broil’ LED will illuminate.
The Time Display will show either ‘Grill’
or ‘Broil’
.
On completion of the Grill / Broil mode, the oven temperature will return to the temperature previously set.
8
Operation
Setting the Oven Programs
Oven can be pre-programmed with up to 20 Program’s. When you receive your oven, the controller is not programmed. To
set programs, carry out the following for each program required:-
1.
ENTER PROGRAMMING MODE.
Press ‘Programs’ button to enter
‘Programming’ mode.
2.
SELECT PROGRAM REQUIRED.
Heating ‘On’
Indicator
Rotate ‘Temperature Control’ to program
required.
Temperature Display will show program
selected.
Press and hold ‘Temperature’ button
until ‘Time’ and ‘Temperature’ displays
and ‘Temperature’ button LED flashes.
Change time and temperature
parameters.
3.
ENTER COOK TEMPERATURE.
Rotate ‘Temperature Control’ to set
cook temperature.
+ to increase the temperature.
- to decrease the temperature.
Timer ‘On’
Indicator
‘Temperature’ Display will show
temperature selected.
4.
ENTER COOK TIME.
Rotate ‘Timer Control’ to set cook time.
+ to increase the time.
- to decrease the time.
‘Time’ Display will show time
selected.
‘Time’ and ‘Temperature’ displays
and ‘Temperature’ button LED flash.
Press ‘Temperature’ button to confirm ‘Time’ and ‘Temperature’ settings.
9
Operator Accessible Parameters
Setting the Operator Accessible Parameters
With the Oven in ‘Stand-By’ mode:-
1.
ENTER THE OPERATOR PARAMETER MODE.
Press 'Grill / Broil' and 'Start / Stop' buttons together.
‘Temperature’ Display will show ‘PAS’.
The ‘Time’ Display will flash.
2.
SET PASSWORD.
Rotate ‘Timer Control’ to set password;
(123) (Operator Password).
Press ‘Light On / Off’ button to confirm password.
‘Temperature’ Display will show one of Parameter Codes.
‘Time’ Display will show value of the parameter.
3.
SETTING THE PARAMETERS.
Rotate ‘Timer Control’ to parameter required.
Press ‘Light’ button to confirm parameter. ‘Time’ display will flash.
While ‘Time’ display is flashing, rotate ‘Timer Control’ to
select value required.
Press ‘Light’ button to confirm value. ‘Time’ display will stop flashing.
4.
EXITING THE PARAMETER MODE.
Press ‘On-Off’ button, to return to ‘Stand-By’ mode.
Table of Operator Accessible Parameters
Parameter
Number.
Description
Turn -On Pre-Heating Temperature. (60 - 260˚C / 140 - 500˚F).
Default
Setting
150ºC
(325ºF)
Light Auto ‘Off’ Setting Time 0 = ‘On/Off’.
1 = 1 minute auto ‘Off’.
2 = 2 minutes auto ‘Off’, etc.
1
Buzzer Volume - Can be adjusted from ‘0’ to ‘10’.
5
Program Pre-Heating Condition - (Can be adjusted from 0 to 30ºC {0 to 54ºF} above pre-heat
temperature).
10
20ºC
(36ºF)
Cleaning and Maintenance
Cleaning Guidelines
c. Pull side racks forward to disengage the location
pins at the rear of rack from the rear wall of the
oven and remove the racks from the oven.
Caution
d. Clean all racks with a mild anti bacterial detergent
and hot water, using a soft bristled brush.
Always turn off electrical power at the
mains supply before commencing cleaning.
e. Dry the racks thoroughly with a dry cloth.
f. To refit the racks, engage the locating pins at the
rear of side rack into the locating holes in the rear
of the oven.
This oven is not water proof.
Do not use
water jet spray to clean interior or exterior
of the appliance.
g. At the same time locate the front of the rack over
the rack securing screw and hand tighten the rack
securing screw .
To achieve the best results, cleaning must be regular and
thorough. If any small faults occur, have them looked at
promptly. Don't wait until they cause a complete
breakdown.
h. Refit the wire oven racks and bottom element guard
to the oven.
NOTE:
Lamp Glass / Fan Baffle
a. Remove the wire racks as shown previously.
• Carefully read and follow the safety instructions on
the label of the cleaning product to be used.
• DO NOT use harsh abrasive scouring pads or
abrasive detergents as they could damage the oven.
Lamp
Glass
• Ensure that any detergent or cleaning material has
been completely removed after each cleaning.
To keep your oven clean and operating at peak efficiency,
follow the procedures shown below:-
Fan
Baffle
Location
Bracket
Oven Cleaning
NOTE:
• If the oven usage is very high, the cleaning
procedure should be carried out on a more frequent
basis.
b. Whilst holding the fan baffle in place, undo the lamp
glass (anti-clockwise) and remove.
• Allow the oven interior to cool to approx 50˚C 120˚F before commencing cleaning.
Stainless Steel Surfaces
a. Thoroughly clean the exterior surfaces of the oven
with, a damp cloth moistened with a mild detergent
solution, or a soft bristled brush.
b. Baked on deposits or discolouration may require a
good quality stainless steel cleaner. Always apply
cleaner when the oven is cold and rub in the
direction of the grain.
Unscrew Anti-Clockwise
Side Racks
c. Pull the fan baffle forward off the location bracket at
lower rear of the oven.
a. Remove wire oven racks and bottom element guard.
b. Partially undo the rack securing screw (anticlockwise) securing side rack to the oven wall, until
the rack is loose.
Rack Securing
Screw
d. Clean fan baffle with mild anti bacterial detergent
and hot water solution using a soft bristled brush.
e. Dry fan baffle thoroughly with a soft dry cloth
before re-fitting.
f. Clean the lamp glass using a soft cloth with a mild
anti bacterial detergent and hot water solution.
Rear
Location
Points
g. Dry the lamp glass thoroughly with a dry cloth.
h. Refit the fan baffle onto the location bracket below
the fan.
i.
11
Whilst holding the fan baffle in place, refit the lamp
glass, screw the glass in clockwise to secure the fan
baffle in place. Do not over tighten lamp glass.
Cleaning and Maintenance
Door Seal
a. To remove door seal, pull the 1 piece seal forward
until it pulls out of the location groove around the
oven. Note the way the seal is fitted to the
oven, with the lip facing inwards.
Door Glass Cleaning
• Ensure that the oven door is cool before cleaning
the oven door glass.
a. Open the oven door.
b. Lift up the bottom of the inner glass at the centre of
the door to unlock from the inner glass retaining
catches and swing the glass inwards towards the
oven.
b. Check for wear and damage to the door seal and
replace as required.
c. Wash the door seal in a sink, taking care not to cut
or damage the seal.
d. Dry the door seal thoroughly.
e. Refit the door seal with lip facing into centre of the
oven.
Top Locking Catches
Refit Seal with Lip
facing inwards
c. Clean both sides of the inner glass and the inner
side of the outer door glass with a conventional
glass cleaner.
f. Press the door seal into the locating groove in the
front face of the oven until the seal is properly
located all around the oven.
d. Dry the oven door thoroughly with a soft dry cloth.
e. Swing the inner glass back towards the outer door.
f. Whilst holding the outer door, lift the inner glass
back onto the locking catches until the inner glass is
securely held.
Push Seal carefully
into locating channel
Periodic Maintenance
NOTE: All maintenance operations should only be
carried out by a qualified service person.
Controls and mechanical parts should be checked and
adjusted periodically by a qualified service person. It is
recommended that the appliance is serviced every 6
months.
Oven Interior
• Allow the oven interior to cool to approx 50˚C 120˚F before commencing cleaning.
a. Remove the oven racks, element guard and the fan
baffle as shown previously.
b. Clean any build up of grease from the oven interior,
using a mild anti bacterial detergent and hot water
solution and a soft bristled brush.
c. Dry the oven thoroughly with a soft dry cloth.
d. Clean the oven regularly with a good quality oven
cleaner.
12
Fault Finding
This section provides a reference to the more common
problems that may occur during the operation of your
oven. This fault finding guide is intended to help you
correct and accurately diagnose problems with your oven.
You may encounter a problem not covered in this section,
please contact your service provider who will require the
following information:-
When fault finding a problem, always use a process of
elimination starting with the simplest solution and working
through to the most complex. Never overlook the obvious.
• The Model and Serial Number of the oven, can be
Fault
Oven does not operate.
Oven Controller operates but No Heat in
Oven.
Oven heats up but fan does not operate.
Door does not close fully.
Oven light not illuminating.
found on the Technical Data Plate located on the
front right hand side panel of the oven.
Possible Causes
Remedy
Mains isolating switch, circuit breaker or
fuses are 'Off' at the power board.
Turn 'On'.
Overtemp tripped (No lights, no power
light).
Call for service.
Overtemp faulty.
Call for service.
Digital Controller faulty
Call for service.
Digital Controller faulty
Refer to ‘Digital Controller Fault Codes’. Call for
service.
Door not closed fully.
Close door. (Refer ‘Door does not close fully’).
Door Switch faulty.
Call for service.
Heating Relay faulty.
Call for service.
Element faulty.
Call for service.
Fan motor faulty.
Call for service.
Fan or fan motor obstructed.
Call for service.
Tray in way of door.
Correctly position tray in rack.
Door mis-aligned.
Re-align door.
Door seal obstruction.
Correctly install door seal. (Refer to the
‘Cleaning’ Section).
Blown bulb.
Replace bulb.
Too high a temperature selected.
Select a lower temperature.
Oven or racks not level.
Check oven racks and level.
Insufficient air space around trays or
baking tins.
Ensure oven racks are spaced to allow air flow
around baking on all shelves.
Oven overloaded with too much product.
Re-load oven.
Opening oven door un-necessarily.
Ensure oven door remains closed during the
baking process.
Oven door seal damaged or faulty.
Check seals and replace if damaged.
Oven vent restricted.
Ensure oven vent not blocked or shrouded.
‘Err 001’ on display.
Probe error.
Call for service.
‘Err 003’ on display.
Digital input error.
Call for service.
Uneven cooking.
13
Electrical Schematics
Electrical Schematic E31D4 Turbofan Oven
14
Replacement Parts List
Important:
Only genuine authorized replacement parts should be used for the servicing and repair of this oven. The instructions
supplied with the parts should be followed when replacing components.
For further information and servicing instructions, contact your nearest authorized service provider or Turbofan Dealer.
When ordering replacement parts, please quote the part number and the description as listed below. If the part required
is not listed below, request the part by description and quote model number and serial number which is shown on the
Technical Data Plate.
Item
Description
234631
234429
234450
234434
Digital Control Board Kit E31D4
Transformer 208 / 240V x 12V AC SEC, 20VA
Encoder
Temperature Probe 20 mm PT1000 1 mtr
234202
234203
234462
234463
Oven Bottom Element, 2000W, 230 - 240V
Oven Bottom Element, 2000W, 208 - 220V
Oven Top Element, 230 - 240V
Oven Top Element, 208 - 220V
013431K
025400
233573
233862
234447
003002
231814
Fan Motor Kit, 208 - 240V, 50/60Hz
Overtemp, 360°C - 680°F
Overtemp Cap
Door Microswitch
Knob Indexed
Oven Lamp Lens
Lamp Bulb G9 25W, Halogen, 230V
234580
235277
235278
234626
234627
234464
232379
Door Roller Catch
Door Roller Catch Strike
Strike Lock Nut
Door Hinge Top
Door Hinge Bottom
Door Seal - E31
Foot Adjustable (73 - 80 mm)
234204
234205
233567
233552
Oven Side Rack LH, E31
Oven Side Rack RH, E31
Oven Rack E31D
Rack Securing Screw
15
Appendix 1 - Oven Door Reversal
11. Remove inner glass latching
studs and fit to opposite
side of door using Loctite
243 to secure.
Reversing the Oven Door
• Refit all screw fasteners using a low-mid strength
thread locking adhesive unless otherwise stated.
• Door reversal should only be carried out by a
suitably competent person.
Remove Latching Studs
Remove the Oven Door Inner Glass.
1. Open the oven door and
open the door inner glass.
2. Remove screw securing
inner glass retaining clip
and remove clip.
3. Lift up inner glass and
remove, ensuring that pivot
spacer is removed from
lower inner glass pivot and
retained.
12. Turn door handle over and
fit to other end of door
where hinges were removed
from. Ensure Flat of handle
is to the outside.
Remove Upper and Lower Door Hinges and Door
Catch.
Remove Screw and
Retaining Clip.
13. Remove bottom door pivot
bolt and spacers and fit
pivot bolt to top door hinge
assembly (as this will be
swapped over and fitted to
bottom of other side of
oven).
Fit Blanking Plugs.
4. Remove black plastic plugs
from top and bottom of
door and fit to holes where
inner glass pivots were
removed from.
Remove the Oven Door.
5. Remove the door roller catch and blanking plate from
the inside of the door and swap these over.
14. Remove the 4 blanking
screws from front of oven.
Swap Roller Catch and
Blanking Plate over.
6. Whilst supporting door,
unscrew and remove top
door pivot bolt from top
door hinge assembly.
7. Remove door and lay on a
flat surface or workbench.
8. Unscrew screws securing
the door handle remove
door handle.
9. Remove top door hinge and
fit to bottom opposite
corner of door.
Remove screws top and bottom
and fit to where hinges removed
from.
Remove Top
Door Pivot Bolt.
15. Remove Hinge Plate from
top of oven and fit
diagonally opposite, to
lower corner.
Remove these screws to remove
top and bottom hinges.
16. Remove Hinge Plate from
bottom of oven and fit
diagonally opposite, to
upper corner.
17. Fit screws removed at Item
14 above to where hinges
were fitted.
Remove Handle
Securing Screws
10. Remove bottom door hinge
and fit to top opposite
corner of door.
Bottom Door Pivot
Bolt and Spacers.
Remove Top Door Hinge
16
Appendix 1 - Oven Door Reversal
18. Remove Blanking Screw and Door Catch from front of
oven and swap around (refer ‘Adjusting Door Catch’).
Door Catch
Adjust Door for Correct Alignment.
Check alignment and operation of the door. Ensure that
the door is correctly aligned horizontally and vertically.
1. To align, slacken off the
upper and lower hinge plates
and correctly align the door.
Re-tighten both hinge plates.
2. Check that the roller catch
correctly retains door in the
closed position.
Slacken these screws to adjust
3. To adjust, slightly loosen
door vertically - horizontally.
screws securing roller catch
and close the door. The
roller catch will centralise
itself.
4. Open door and tighten roller
catch securing screws.
Blanking Screw
Locking Nut
19. Fit door spacers removed at Item 13 previously, to
lower hinge pivot bolt.
Oven Door Re-Fitting
Fit the Door.
1. Refit oven door by locating
bottom of door onto bottom
hinge plate pivot bolt and
spacers.
2. Fit top of door into top
hinge plate and secure with
top pivot bolt.
Top Door Pivot Bolt.
Adjusting Door Catch
If the door sealing requires adjustment, carry out the
following to adjust:1. Check that the door seals
correctly when closed, by
placing a sheet of paper
between the door and the
seal.
2. Close the door on the paper
and attempt to withdraw the
paper by firmly tugging on
the paper. The paper should
just pull out with some
resistance but without tearing.
3. To adjust the door catch, loosen the locking nut on
the door catch:-
Fit Inner Glass to Door.
NOTE: It is important to ensure that the inner glass
is fitted correctly and that the glass pivots at
the hinge end of the door and not the handle
end.
3. Fit pivot spacer removed at Item 3 on previous page,
to the lower inner glass pivot and locate inner glass
lower pivot into position on inside of door.
4. Locate top pivot of inner glass
Screw and
into top of door and secure in
Retaining Clip.
position with inner glass
retaining clip.
5. Lift inner glass up onto locking
catch to lock glass into
position.
a. If the paper withdraws easily, screw the door
catch ‘In’ by ½ a turn and repeat the test above
until adjusted correctly.
b. If the paper cannot be withdrawn and the door
springs open, screw the door catch ‘Out’ by ½ a
turn and repeat the test above until adjusted
correctly.
4. Tighten the locking nut on the door catch.
Inner Glass Locking Catch
17