Vivitek D5I8ZHDL User`s manual

Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2011
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
DisplayPort is a registered trademark of the Video Electronics Standards Association, registered in
the U.S. and the other countries.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
—i—
DLP Projector—User’s Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
¾
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
¾
Follow all warnings and cautions in this manual and on the unit case.
¾
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
¾
Do not place the unit on an unstable surface, cart, or stand.
¾
Avoid using the system near water, in direct sunlight, or near a heating device.
¾
Do not place heavy objects such as books or bags on the unit.
— ii —
PPrreeffaaccee
Projector Installation Notice
¾
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease
dramatically, and may lead to other unpredictable damages.
¾
Allow at least 50 cm clearance around the exhaust vent.
¾
Ensure that the intake vents do not recycle hot air from the exhaust vent.
¾
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.
¾
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.
– iii –
DLP Projector—User’s Manual
Verify Installation Location
¾
To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.
¾
The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
¾
Verify if the voltage is stable, grounded properly and there is no electricity leakage.
¾
Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.
¾
Turn on Altitude Mode when located in high altitude areas
¾
The projector can only be installed upright or inverted.
¾
When installation the bracket, make sure the weight limit is not exceed and firmly secured.
¾
Avoid installing near air conditioner duct or subwoofer.
¾
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
¾
Keep your product away from fluorescent lamps to avoid malfunction
caused by IR interference
¾
The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted
tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.
¾
The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected
to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even
DAMAGE the port.
¾
Install the projector above 200cm to avoid damage.
¾
The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
¾ Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
¾
Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
¾
Keep the outlet at least 100cm away from the inlets of other projectors
¾
The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
¾ Make sure there is no object blocking air input within 30 cm.
¾
Keep the inlet away from other heat sources
¾
Avoided heavy dust area
— iv —
PPrreeffaaccee
Choosing a Projector
Edge blending application
¾ Not only brightness, bright balances, lens but stability is important too when choosing a projector.
¾
A projector need 30 to 60 minutes warm up to adjust properly.
¾
After lens shift, there should not be any optical distortion such as trapezoidal and barrel shape
distortions.
¾
Quick dis-assemble lens need to be firmly secured, the electric motor cannot be mistakenly shift.
The screen should not be offset for long time use or during booting up and shutting down the
projector.
¾
Projector six-axis colors (R,G,B,Y,C,W). Projector adjust functions require: Hue, Saturation, Gain
¾
Vertical or 360 degree projection application. Needs to VERIFY engineering design of lamp aging
to avoid conflict with client.
HDMI Cable
Edge blending signal needs to use digital transfer, the 4 pairs of TMDS transfer impedance require 100 Ω
diameter as following to maintain signal quality:
¾
5M
: AWG 26
¾
10 M : AWG 24
¾
15 M : AWG 22
¾
20 M : AWG 22
¾
25 M : AWG 22
–v–
DLP Projector—User’s Manual
Power Safety
¾
Only use the supplied power cord.
¾
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
¾
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 42
for clear and safe instructions for this procedure. Before replacing the lamp:
¾
Unplug the power cord.
¾
Allow the lamp to cool for about one hour.
Cleaning the Projector
¾
Unplug the power cord before cleaning. See Cleaning the Projector page .45
¾
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 57.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
— vi —
PPrreeffaaccee
Main Features
•
Lightweight unit, easy to pack away and transport.
•
Compatible with all major video standards including NTSC, PAL, and SECAM.
•
A high brightness rating allows for presentations in daylight or in lit rooms.
•
Supports resolutions up to WUXGA at 16.7 million colors to deliver crisp, clear images.
•
Flexible setup allows for front, rear projections.
•
Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
•
Input source automatically detected.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
Note:
When resolution setting to WUXGA will need to enable reduce blanking function
– vii –
DLP Projector—User’s Manual
Table of contents
GETTING STARTED........................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-right View ............................................................................................................................................................ 2
Top view—On-screen Display (OSD) buttons and LEDs....................................................................................... 3
Rear view....................................................................................................................................................................... 4
Bottom view................................................................................................................................................................... 6
REMOTE CONTROL PARTS ................................................................................................................................................... 7
REMOTE CONTROL OPERATING RANGE ............................................................................................................................... 9
PROJECTOR AND REMOTE CONTROL BUTTONS .................................................................................................................... 9
SETUP AND OPERATION............................................................................................................................................... 10
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................. 10
INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 11
Removing the Existing Lens From the Projector ................................................................................................... 11
Installing the New Lens ............................................................................................................................................. 12
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 13
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 15
ADJUSTING PROJECTED IMAGE POSITION USING SHIFT ..................................................................................................... 16
Adjusting the vertical image position ....................................................................................................................... 16
Adjusting the horizontal image position .................................................................................................................. 17
Shift Range Diagram ................................................................................................................................................. 17
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 18
ADJUSTING THE VOLUME .................................................................................................................................................. 19
ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 20
OSD MENU CONTROLS ..................................................................................................................................................... 20
Navigating the OSD ................................................................................................................................................... 20
SETTING THE OSD LANGUAGE .......................................................................................................................................... 21
OSD MENU OVERVIEW ..................................................................................................................................................... 22
IMAGE SETTINGS ............................................................................................................................................................... 23
Advanced Feature...................................................................................................................................................... 24
DISPLAY SETTINGS ............................................................................................................................................................ 26
Keystone...................................................................................................................................................................... 27
HSG Adjustment......................................................................................................................................................... 28
White Balance............................................................................................................................................................. 29
AUDIO SETTINGS ............................................................................................................................................................... 30
TIMER SETUP ..................................................................................................................................................................... 31
BASIC SETUP ..................................................................................................................................................................... 32
Menu Setting ............................................................................................................................................................... 33
Lamp Setting ............................................................................................................................................................... 33
ADVANCED SETUP ............................................................................................................................................................. 34
Network Settings ........................................................................................................................................................ 35
INFORMATION MENU ......................................................................................................................................................... 41
MAINTENANCE AND SECURITY .................................................................................................................................. 42
REPLACING THE PROJECTION LAMP................................................................................................................................... 42
CLEANING THE PROJECTOR................................................................................................................................................ 45
Cleaning the Lens ...................................................................................................................................................... 45
Cleaning the Case...................................................................................................................................................... 45
USING THE PHYSICAL LOCK .............................................................................................................................................. 46
Using the Kensington® Lock ..................................................................................................................................... 46
Using the Security Chain Lock ................................................................................................................................. 46
TROUBLESHOOTING...................................................................................................................................................... 47
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 47
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 47
LED ERROR MESSAGES ..................................................................................................................................................... 48
— viii —
PPrreeffaaccee
IMAGE PROBLEMS .............................................................................................................................................................. 48
LAMP PROBLEMS ............................................................................................................................................................... 49
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 49
AUDIO PROBLEMS ............................................................................................................................................................. 49
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 49
HDMI Q & A .................................................................................................................................................................... 50
SPECIFICATIONS ............................................................................................................................................................. 51
SPECIFICATIONS................................................................................................................................................................. 51
PROJECTION DISTANCE VS. PROJECTION SIZE (1080P) ...................................................................................................... 52
Projection Distance and Size Table......................................................................................................................... 52
TIMING MODE TABLE ........................................................................................................................................................ 54
PROJECTOR DIMENSIONS ................................................................................................................................................... 56
REGULATORY COMPLIANCE....................................................................................................................................... 57
FCC WARNING .................................................................................................................................................................. 57
CANADA ............................................................................................................................................................................ 57
SAFETY CERTIFICATIONS ................................................................................................................................................... 57
APPENDIX I........................................................................................................................................................................ 58
RS-232C PROTOCOL.......................................................................................................................................................... 58
APPENDIX II....................................................................................................................................................................... 62
APPENDIX III...................................................................................................................................................................... 63
D5185HD EDGE BLENDING .............................................................................................................................................. 63
Equipment Requirement............................................................................................................................................ 63
Edge Blending Guideline........................................................................................................................................... 63
– ix –
DLP Projector – User’s Manual
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
PROJECTOR WITH LENS CAP
REMOTE CONTROL
(BATTERIES NOT INCLUDED)
RGB CABLE
POWER CORD
CD-ROM
(THIS USER’S MANUAL)
WARRANTY CARD
QUICK START CARD
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
–1–
DLP Projector—User’s Manual
Views of Projector Parts
Front-right View
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
IR receiver
Receives IR signal from remote control
7
2.
Lens
Projection Lens
3.
Focus ring
Focuses the projected image
4.
Zoom ring
Enlarges the projected image
5.
Height adjuster
Adjusts level of projector
6.
Function keys
See Top view—On-screen Display (OSD) buttons and LEDs.
7.
Lamp cover
Removes cover to replace lamp
42
8.
Vertical lens shift
Adjusts the image position vertically
16
9.
Horizontal lens shift
Adjusts the image position horizontally
17
10.
Lens release button
Press the release button before removing the
lens
11
18
15
3
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
—2—
DLP Projector – User’s Manual
Top view—On-screen Display (OSD) buttons and LEDs
ITEM
1.
LABEL
MENU
2.
DESCRIPTION
z
Navigates and changes settings in the OSD
z
Quick Menu – For Keystone
ENTER
Enter or confirm highlighted OSD menu item
4.
BLANK
Displays a blank screen and mutes audio
6.
AUTO
7.
8.
9.
SOURCE
PAGE:
Opens and exits OSD menus
3.
5.
SEE
z
Navigates and changes settings in the OSD
z
Quick Menu – For Volume -
20
20
Optimizes image size, position, and resolution
z
Navigates and changes settings in the OSD
z
Quick Menu – For Volume +
z
Navigates and changes settings in the OSD
z
Quick Menu – For Keystone
Alternate input source
–3–
20
DLP Projector—User’s Manual
Rear view
1
2
3
4 5
6
7
8 10
9 11
12
13
14
27
ITEM
26 25 23 22 21
24
LABEL
20
18 17 15
19
16
DESCRIPTION
SEE PAGE:
1.
RJ-45
Connect a LAN cable from Ethernet
2.
DP
Connect a DISPLAYPORT cable from a DISPLAYPORT device
3.
HDMI
Connect the HDMI cable from a HDMI device
4.
DVI
Connect the DVI cable from a computer
5.
VGA1
Connect an RGB cable from a computer or a video enabled device
6.
POWER
Turns the projector on or off (main power switch must
be turned on first).
Press to place the projector in standby mode.
7.
PWR LED
Solid Blue
Lamp ready
Blinking Red
Error code
Flashing Red
Powering on/ cooling
Solid Red
Over Temperature
Blinking Red
Error code
Error code
8.
TEMP LED
9.
LAMP LED
Blinking Red
10.
AUDIO IN
(VGA1)
Connect an AUDIO cable from the input device
11.
AUDIO IN
(VGA2)
Connect an AUDIO cable from the input device
12.
IR receiver
Receive IR signal from remote control
13.
RS-232
Connects RS-232 serial port cable for remote control
—4—
13
48
DLP Projector – User’s Manual
ITEM
LABEL
DESCRIPTION
SEE PAGE:
14.
12V OUT
Connect the 12V OUT (Screen Trigger-- For screen controllers used)
15.
WIRE IR
Wire remote control connector (connect with wire remote connector of the
Remote Control set)
16.
AUDIO 1
Connect an AUDIO cable from the input device
17.
AUDIO 2
Connect an AUDIO cable from the input device
Share audio input with DVI.
18.
VIDEO
Connect the COMPOSITE cable from a video device
19.
S-VIDEO
Connect the S-video cable from a video device
20.
COMPONENT
Connect the Component cable to a display
21.
Power switch
Turns on/off the projector
22.
AC IN
Connects the power cable
23.
VGA2
Connect an RGB cable from a computer or a video enabled device
24.
VGA OUT
Connect the RGB cable to a display
(Pass through by VGA1 only)
25.
AUDIO OUT
Connect an AUDIO cable for audio loop through
26.
Security chain
lock
Helps protect the projector from unauthorized use
27.
Kensington Lock
Secures to permanent object with a Kensington® Lock
system
13
Note:
For 12V OUT
y To use this feature, you must plug in the connector before turn on/off the projector.
y Screen controllers are supplied and supported by screen manufacturers.
y Do not use this jack for anything other than intended use.
Note:
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the
S-VIDEO connector. S-VIDEO provides a better quality signal.
–5–
46
DLP Projector—User’s Manual
Bottom view
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a
ceiling
15
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a
period of 60 seconds.
—6—
DLP Projector – User’s Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
–7–
DLP Projector—User’s Manual
ITEM
1.
2.
3.
4.
LABEL
DESCRIPTION
Power OFF
Turns the projector off
DVI
Displays the DVI source selection
VGA
Displays the VGA source selection
DP
Displays the Display Port source selection
5.
Up cursor /
Keystone+
Navigates and changes settings in the OSD
Quick Menu – For Keystone
6.
7.
ENTER
Enters and confirms settings in the OSD
Right cursor
Navigates and changes settings in the OSD
8.
Down cursor /
Keystone-
Navigates and changes settings in the OSD
Quick Menu – For Keystone
9.
10.
11.
12.
13.
3D
Activate 3D video (not available in D5180HD series)
PICTURE MODE
Changes the Display Mode setting
SOURCE
Alternate input source
CONTRAST
Displays the contrast settings bar
BRIGHT
Displays the brightness setting bar
14.
SHARP
Displays the sharpness setting bar
15.
COLOR
Displays the color setting bar
16.
FREEZE
Freezes/unfreezes the on-screen picture
17.
VOL +
Adjusts volume
18.
AUTO
Auto adjustment for frequency, phase, and position
19.
VOL -
Adjusts volume
20.
21.
22.
BLANK
Makes the screen blank
TINT
Displays the tint setting bar
MUTE
Mutes the built-in speaker
23.
STATUS
Opens the OSD Status menu (the menu only opens when an input
device is detected)
24.
25.
ASPECT RATIO
Displays the ASPECT RATIO selections
MENU
Opens the OSD
26.
Left cursor
Navigates and changes settings in the OSD
27.
28.
29.
30.
31.
32.
COMP
Displays the Component source selection
VIDEO
Displays the VIDEO source selection
HDMI 1
Displays the HDMI 1 source selection
Power ON
Turns the projector on
Status LED
Lights when the remote control is used
IR transmitter
Transmits signals to projector
Wired remote connector
Wired remote function
33.
—8—
SEE PAGE:
13
20
20
13
DLP Projector – User’s Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are limited in use.
–9–
DLP Projector—User’s Manual
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
2.
3.
Remove the battery compartment
cover by sliding the cover in the direction of the arrow.
Insert the battery with the positive
side facing up.
Replace the cover.
Caution:
1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
— 10 —
DLP Projector – User’s Manual
Installing or Removing the Optional Lens
Caution:
y Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts.
y Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans
stop, and turn off the main power switch.
y Do not touch the lens surface when removing or installing the lens.
y Keep fingerprints, dust or oil off the lens surface.
y Do not scratch the lens surface.
y Work on a level surface with a soft cloth under it to avoid scratching.
y If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Removing the Existing Lens From the Projector
1.
2.
3.
4.
5.
Pull and release the top cover to
open as shown.
Push the LENSE RELEASE button
to the unlock position.
Grasp the lens.
Rotate the lens counterclockwise.
The existing lens will be disengaged.
Pull out the existing lens slowly.
– 11 –
DLP Projector—User’s Manual
Installing the New Lens
1.
Align the notches and correctly position the electrical contact pad as
shown in the picture.
Note:
Pin of IRIS should be in the direction
as shown in the picture.
2.
Rotate the lens clockwise until you
feel it click into place.
— 12 —
DLP Projector – User’s Manual
Starting and Shutting down the Projector
1.
2.
3.
Remove the lens cap.
Securely connect the power cord
and signal cable. When connected,
the power led will turn red.
Turn on the lamp by pressing
“
” button on the rear of the
projector or “
” on the remote
control.
The PWR LED will now flash red
The startup screen will display in
approximately 30 seconds. The first
time you use the projector, you can
select your preferred language from
quick menu after the startup screen
display.
– 13 –
DLP Projector—User’s Manual
4.
5.
If more than one input device is connected, press the SOURCE button
to scroll among devices.
(Component is supported through
the RGB to COMPONENT
ADAPTER.)
•
DVI: DVI
•
HDMI: HDMI
•
VGA1/ VGA2: Analog RGB
•
DP: DISPLAYPORT input
•
Component Video: DVD input YCbCr / YPbPr,
or HDTV input YPbPr via HD15 connector
•
S-Video: Super video (Y/C separated)
•
Composite Video: Traditional composite video
When the “Power Off? /Press
Power again” message appears,
press the POWER button. The projector turns off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has
cooled down.
— 14 —
DLP Projector – User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
1.
2.
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection
angle.
•
Ensure the cables are in a safe location. You could trip over them.
To raise the level of the projector,
twist the adjusters counter clockwise
To lower the level of the projector,
lift the projector and twist the adjusters clockwise.
– 15 –
DLP Projector—User’s Manual
Adjusting Projected Image Position Using Shift
The Shift feature provides a lens shift function that can be used to adjust the position of the projected
image either horizontally or vertically within the range detailed below.
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio
than traditional lens shift systems.
Adjusting the vertical image position
The vertical image height can be adjusted between 120% and -40% of half image height. Note that
the maximum vertical image height adjustment can be limited by the horizontal image position. For
example it is not possible to achieve the maximum vertical image position height detailed above if the
horizontal image position is at maximum. Please consult the Shift Range diagram below for further
clarification.
Screen Height
(H)
Screen
-40% offset
100%
0% offset
H x 20%
120% offset
Distance
(L)
— 16 —
DLP Projector – User’s Manual
Adjusting the horizontal image position
With the lens in the center position the horizontal image position can be adjusted to the left or right by
up to a maximum of 10% of the half image width. Note that the maximum horizontal image height adjustment can be limited by the vertical image position. For example it is not possible to achieve the
maximum horizontal image position if the vertical image position is at maximum. Please consult the
Shift Range diagram below for further clarification.
MENU
BLANK
ENTER
AUTO
SOURCE
Shift Range Diagram
Wx10%
Wx10%
W
Hx120%
Hx100%
H=Image Height
Max H image shift=Hx120%
When Wx10%, Max image shift=Hx100%
– 17 –
DLP Projector—User’s Manual
Adjusting the Zoom, Focus and Keystone
1.
2.
3.
Use the Image-zoom
control (on the projector
only) to resize the projected image and
screen size.
Use the Image-focus
control (on the projector
only) to sharpen the
projected image.
Use the KEYSTONE
buttons (on the projector or the remote
control) to correct image-trapezoid (wider
top or bottom)
effect.
Remote control and OSD panel
4.
The keystone control
appears on the display.
— 18 —
DLP Projector – User’s Manual
Adjusting the Volume
1.
2.
3.
Press the Volume +/-.
buttons on the remote
control.
The volume control
appears on the display.
Press the
or buttons on the keypad to
adjust Volume +/-.
Press the MUTE button
to turn off the volume
(This feature is available only on the
remote).
– 19 –
DLP Projector—User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the
projector.
3
1
1
3
5
6
7
1
7
4
2
2
5
4
6
1
1. To enter the OSD, press the MENU button.
2. There are seven menus. Press the cursor ▲▼ button to move through the
menus.
3. Select one of the main menu, Press
ENTER or ► button into submenu.
Press the cursor ▲▼ button to move up
and down in submenu.
4. Select one of the submenu, Press
ENTER or ► button into the selected
item. Press ▲▼or ◄► to change values for settings.
5. Press MENU to close the OSD or leave
a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the Horizontal/Vertical Position items in the Computer menu can only be modified when connected to a PC.
Items that are not available cannot be accessed and are grayed out.
— 20 —
DLP Projector – User’s Manual
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ▲▼ button to navigate to Basic Setup.
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ▲▼ button until the language you want is highlighted.
4. Press the MENU button twice to close the OSD.
– 21 –
DLP Projector—User’s Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
Image Settings
Picture Mode
Movie/Bright/Normal/User 1/User 2/User 3
Brightness
Contrast
Saturation
Tint
Sharpness
Advanced
Reset
Image Settings>> Advanced(PC Detail Adjustment)
Yes/No
Auto Adjustment
Image Position
Up/Down/Left/Right
Phase
Frequency
Image Settings>> Advanced(Video Adjustment)
Noise Reduction
Flesh Tone
Off/Low/Moderate/High
Dynamic Contrast
Display Settings
Aspect Ratio
Auto/16:9/4:3/Letter Box/Real
Keystone
V Keystone/H Keystone/Reset
Projection
Front Table/Front Ceiling/Rear Table/Rear Ceiling
Gamma
Color Temperature
Lamp Native/Warm/Normal/Cool/Cooler/High Cool
HSG Adjustment
White Balance
Display Settings>> HSG Adjustment
Primary Color
Red Gain/Green Gain/Blue Gain/Red Offset/Green Offset/Blue Offset
R/G/B/Y/C/M
Hue
Saturation
Gain
White Gain Red
White Gain Green
White Gain Blue
Audio Settings
Volume
Mute
Timer Setup
Basic Setup
Off/On
Sleep Timer
Off / 30 Min / 1 Hr / 2 Hr / 3 Hr / 4Hr / 8Hr / 12 Hr
Auto Power Off
Off / 5 Min / 10 Min / 15 Min / 20 Min / 25 Min / 30 Min
Language
English/ Danish/ Dutch/ Finnish/ Français/ Deutsch/ Italiano/ Korean/ Norsk/ Polish/ Português (Latin American)/
Russian/ Simplified Chinese/ Traditional Chinese/ Spanish/ Swedish/ Turkish/ Bahasa
Auto Scan
Off/On
Menu Settings
Menu position
Top-Left/Top-Right/Center/Bottom-Left/Bottom-Right
Display Time
5 Sec / 10 Sec / 15 Sec / 20 Sec / 25 Sec / 30 Sec
Transparency
Splash Logo
Logo/Blue/Black
Background Color
Purple/Blue/Black
Lamp Setting
Advanced Setup
Lamp Mode
Boost/Standard
Reset Lamp Timer
Yes/No
High Altitude Mode
Off/On
Network Settings
Control By
Network Status
Reset All
Information
Source
Resolution
Lamp Hour
Firmware Version
— 22 —
Yes/No
RS232/RJ45
Network State / DHCP (On / Off) / IP Address / SubNet Mask /
Default Gateway / DNS / Apply
DLP Projector – User’s Manual
Image Settings
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Image
Settings menu. Press ENTER / ► button to move up and down in the Image Settings item. Press
ENTER / ► button to entry item. Press ▲▼ or ◄► to change values for settings.
ITEM
DESCRIPTION
Picture Mode
Press the cursor ▲▼ button to set the Picture Mode.
Brightness
Press the cursor ◄► button to adjust the display brightness.
Contrast
Press the cursor ◄► button to adjust the display contrast.
Saturation
Press the cursor ◄► button to adjust the Saturation.
Tint
Press the cursor ◄► button to adjust the Tint.
Sharpness
Press the cursor ◄► button to adjust the display sharpness level.
Advanced
Press ENTER / ► to enter the Advanced menu. See Advanced Feature on page 24.
Reset
Press the cursor ▲▼ button to set the “YES” or :NO”. Press ENTER to reset Picture
Mode default values.
– 23 –
DLP Projector—User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ▲▼ to move to the Image Settings menu.
Press ENTER / ► button in the Advanced item. Press ENTER / ► button to entry item.Press▲▼to
move to the Advanced item and then press ENTER or ►or ◄► to setting value.
PC Detail Adjustment
ITEM
DESCRIPTION
Auto Adjust
Press ENTER or ► button; or Press the Auto button on the projector keypad or the
Auto button on the remote control to automatically adjust frequency, phase, and position.
Image Position
Press ENTER / ► button to Image Position submenu, Press the ▲▼ or ◄► buttons
to Enter H/V position adjust Image Position.
This function is only available when a PC signal (analog RGB) is selected.
Phase
Press the ◄► buttons to adjust the A/D sampling clock.
Frequency
Press the ◄► buttons to adjust the A/D sampling number.
Image Position
— 24 —
DLP Projector – User’s Manual
Video Adjustment
ITEM
DESCRIPTION
Noise Reduction
Press ENTER / ► button to enter Noise Reduction submenu, Press the cursor ◄►
button to adjust the Noise Reduction.
Flesh Tone
Press the cursor ▼▲ button to select different Flesh Tone.
Dynamic Contrast
Press the cursor ▼▲ button to select different Dynamic Contrast.
Noise Reduction
– 25 –
DLP Projector—User’s Manual
Display Settings
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Display
Settings menu. Press ENTER / ► button to move up and down in the Display Settings item. Press
ENTER / ► button to entry item. Press▲▼ or ◄► to change values for settings.
ITEM
DESCRIPTION
Aspect Ratio
Press the cursor▲▼button to set the Aspect Ratio.
(Range: Auto/ 16:9/ 4:3/ Letter Box/ Real)
Keystone
Press the ENTER/ ► button to enter the Keystone sub menu.
(This function will be disabled when Auto keystone is activated)
Projection
Press the cursor▲▼button to select different projection type.
Gamma
Press the cursor ◄► button to adjust the gamma correction of the display.
Color Temp
Press the cursor▲▼button to set the Color Temp
HSG Adjustment
Press the ENTER/ ► button to enter the HSG (Hue/Saturation/Gain) Adjustment sub
menu.
See HSG Adjustment on page 28
White Balance
Press the ENTER/ ► button to enter the White Balance sub menu.
See White Balance on page 29
— 26 —
DLP Projector – User’s Manual
Keystone
Press the ENTER/ ► button to enter the Keystone sub menu. Press ◄► to change values for settings.
V Keystone
Press the cursor ◄► button to adjust the V Keystone
(This function will be disabled when Auto keystone is activated)
H Keystone
Press the cursor ◄► button to adjust the H Keystone
(This function will be disabled when Auto keystone is activated)
Reset
Press ENTER button to reply Keystone default values.
Applying keystone to correct image due to projection angle will result in minor distortion compared to
actual image
– 27 –
DLP Projector—User’s Manual
HSG Adjustment
Press the ENTER/ ► button to enter the HSG Adjustment item. Press▲▼ or ◄► to change values
for settings.
ITEM
DESCRIPTION
Primary Color
Press the ▲▼ buttons to set the Primary Color.
Notes: There are six colors (R/ G/ B/ C/ M/ Y) to be customized.
Hue
Press the ◄► buttons to adjust the Hue.
Saturation
Press the ◄► buttons to adjust the Saturation.
Gain
Press the ◄► buttons to adjust the Gain.
White Gain Red
Press the cursor ◄► button to adjust the White Gain Red.
White Gain Green
Press the cursor ◄► button to adjust the White Gain Green.
White Gain Blue
Press the cursor ◄► button to adjust the White Gain Blue.
— 28 —
DLP Projector – User’s Manual
White Balance
Press the ENTER button to enter the White Balance sub menu.
ITEM
DESCRIPTION
Red Gain
Press the ◄► buttons to adjust the Red Gain.
Green Gain
Press the ◄► buttons to adjust the Green Gain.
Blue Gain
Press the ◄► buttons to adjust the Blue Gain.
Red Offset
Press the ◄► buttons to adjust the Red Offset.
Green Offset
Press the ◄► buttons to adjust the Green Offset.
Blue Offset
Press the ◄► buttons to adjust the Blue Offset.
– 29 –
DLP Projector—User’s Manual
Audio Settings
Press the MENU button to open the OSD menu. Press the cursor▲▼ button to move to the Audio
Settings menu. Press ENTER / ► button to move up and down in the Audio Settings item. Press
ENTER / ► button to entry item. Press▲▼ or ◄► to change values for settings.
ITEM
DESCRIPTION
Volume
Press the ◄► buttons to adjust the audio volume.
(Range: 0~10)
Mute
Press the ▲▼ buttons to turn on or off the speaker.
— 30 —
DLP Projector – User’s Manual
Timer Setup
Press the MENU button to open the OSD menu. Press the cursor▲▼ button to move to the Timer
Setup menu. Press ENTER / ► button to move up and down in the Timer Setup item. Press ENTER
/ ► button to entry item. Press the cursor ▲▼ button to move up and down in the Timer Setup item.
Press▲▼to change values for settings.
ITEM
DESCRIPTION
Sleep Timer
Press the cursor▲▼buttons to set Sleep timer. The projector automatically turns off
after the preset period of time.
(Range: Off/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr).
Auto Power Off
Press the cursor▲▼buttons to set the Auto Power Off timer. The projector automatically turns off if no input source is detected after the preset period of time.
(Range: Off/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min).
– 31 –
DLP Projector—User’s Manual
Basic Setup
Press the MENU button to open the OSD menu. Press the cursor▲▼button to move to the Basic
Setup menu. Press ENTER / ► button to move up and down in the Basic Setup item. Press ENTER
/ ► button to entry item. Press▲▼to change values for settings.
ITEM
DESCRIPTION
Language
Press the cursor▲▼button to select a different localization Menu.
Auto Scan
Press the cursor▲▼button to enable or disable the automatically searching of all input port to find out the valid source.
Menu Setting
Press the ENTER/ ► button to enter the Menu Setting sub menu.
See Menu Setting on page 33.
Splash Logo
Press the cursor▲▼button to set desired startup screen when lamp warming up.
Background Color
Press the cursor▲▼button to set desired background color when in no signal.
Lamp Setting
Press the ENTER/ ► button to enter the Lamp sub menu.
See Lamp Setting on page 33.
— 32 —
DLP Projector – User’s Manual
Menu Setting
ITEM
DESCRIPTION
Menu Position
Press the cursor▲▼button to select a different OSD location.
Menu Display Time
Press the cursor▲▼button to select OSD timeout delay.
Transparency Menu
Press the cursor ◄► button to select OSD transparency
Lamp Setting
ITEM
DESCRIPTION
Lamp Mode
Press the cursor▲▼button to select the lamp mode for higher brightness or lower
brightness to save lamp life.
Reset Lamp Timer
Press the▲▼button to reset the Lamp Hour after the lamp is replaced
– 33 –
DLP Projector—User’s Manual
Advanced Setup
Press the Menu button to open the OSD menu. Press ▲▼ to move to the Advanced Setup menu
Press ENTER / ► button to move up and down in the Advanced Setup item. Press ENTER / ► button to entry item. Press ▲▼to change values for setting.
ITEM
DESCRIPTION
High Altitude Mode
Press the cursor ▲▼ buttons to turn on or off High Altitude Mode.
Recommend to turn ON when the altitude of the environment is higher than 1500m
(4921ft).
Network Settings
Press ENTER / ► to enter the Network menu. See page 35 for more information on
Network Settings.
Reset All
Press the ▲▼ button to enter reset all settings.
— 34 —
DLP Projector – User’s Manual
Network Settings
ITEM
DESCRIPTION
Press the▲▼buttons to select projector remote command control.
Selecting RJ45 enables RJ45 control and disables the RS232 port.
Selecting RS232 enables RS232 control and disables the RJ45 network port.
When RS232 control is enabled, the serial port settings are fixed to:
Control By
115200 Baud;8-bits;No parity;1 Stop-bit;No flow control
(Range: RS232/ RJ45)
Note: this setting changes the standby power:
RS232 = <0.5W (Default)
RJ45 = <10W
Network Status
Press the ENTER/ ► button to enter the Network Status sub menu.
See Network Status on page 36.
– 35 –
DLP Projector—User’s Manual
Network Status
ITEM
Network Status
DESCRIPTION
Displays the network connection status.
Press▲▼to turn DHCP On or Off.
DHCP
Note: If user selects ‘DHCP’ Off, it will still use user apply IP setting or default RJ45
IP setting. If user selects ‘DHCP’ On, it will use dynamic IP address and IP setting
from DHCP server on the network..
IP Address
Press the▲▼buttons to change value IP address if DHCP is turned off.
Subnet Mask
Press the▲▼buttons to change value Subnet Mask if DHCP is turned off.
Gateway
Press the▲▼buttons to change value Gateway address if DHCP is turned off.
DNS
Press the▲▼buttons to change value DNS name if DHCP is turned off.
Apply
Press▲▼ to confirm settings.
— 36 —
DLP Projector – User’s Manual
For simplicity and ease of operation, the projector provides diverse networking and remote management
features.
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off,
Brightness and Contrast settings. Also, projector status information, such as: Video-Source, Sound-Mute,
etc.
LAN_RJ45
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop).
2. On the PC (Laptop), select Start → Control Panel → Network Connections.
– 37 –
DLP Projector—User’s Manual
3. Right-click on Local Area Connection, and select Properties.
4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP).
5. Click Properties.
6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
— 38 —
DLP Projector – User’s Manual
7. Press the Menu button on the projector.
8.
Select Advanced Setup → Network Settings → Control By → RJ45 option.
9.
After getting into Network Status, input the following:
` DHCP: Off
` IP Address: 10.10.10.10
` Subnet Mask: 255.255.255.0
` Gateway: 0.0.0.0
` DNS Server: 0.0.0.0
10. Press
(Enter) / ► to confirm settings.
Open a web browser
(for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher).
11. In the Address bar, input the IP address: 10.10.10.10.
12. Press
(Enter) / ►.
The projector is setup for remote management. The LAN/RJ45 function displays as follows.
– 39 –
DLP Projector—User’s Manual
CATEGORY
Crestron Control
Projector
Network Configuration
User Password
Admin Password
ITEM
INPUT-LENGTH
IP Address
14
IP ID
3
Port
5
Projector Name
10
Location
10
Assigned To
10
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
Enabled
(N/A)
New Password
15
Confirm
15
Enabled
(N/A)
New Password
15
Confirm
15
For more information, please visit http://www.crestron.com.
— 40 —
DLP Projector – User’s Manual
Information Menu
Press the MENU button to open the OSD menu. Press the cursor▲▼button to move to the
Information Menu..
ITEM
DESCRIPTION
Source
Displays the activated input source.
Resolution
Displays the native resolution of input source.
Lamp Hour
Displays the number of hours the lamp has been in use.
Firmware Version
Displays the firmware version of the projector.
– 41 –
DLP Projector—User’s Manual
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and broken shards of the lamp.
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the projector. Glass fragments could fall if the lamp has been burned out.
! IF A LAMP EXPLODES
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come
out of the exhaust vent. The gas contains toxic mercury.
Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor
immediately.
1.
2.
3.
Switch off the power to the
projector by pressing the
POWER button.
Allow the projector to cool
down at least 30 minutes.
Disconnect the power
cord.
— 42 —
DLP Projector – User’s Manual
4.
5.
6.
7.
Unlock the lamp cover.
Pull up and remove the
cover.
Use a screwdriver to remove the screws from the
lamp module.
Pull out the lamp module.
– 43 –
DLP Projector—User’s Manual
8.
Reverse steps 1 to 7 to
install the new lamp
module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.
Note:
The lamp module must sit
securely in place and the
lamp connector must be
connected properly before
tightening the screws.
9.
Turn on the projector and reset the lamp after the lamp module is replaced.
Lamp Reset:
Press Menu → Select Basic Setup →Lamp Setting →Reset Lamp Timer → Press the
▲▼ buttons to adjust the settings.
— 44 —
DLP Projector – User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to
the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and
then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
– 45 –
DLP Projector—User’s Manual
Using the Physical Lock
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,
http://www.Kensington.com.
Using the Security Chain Lock
In addition to the password protection function and the Kensington lock, the Security Chain Opening
helps protect the PROJECTOR from unauthorized use.
See the following picture.
— 46 —
DLP Projector – User’s Manual
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions.
•
Use some other electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in suspending mode.
•
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.
– 47 –
DLP Projector—User’s Manual
LED Error Messages
ERROR CODE MESSAGES
POWER LED
TEMP LED
LAMP LED
BLUE
RED
RED
RED
Lamp Ready
ON
-
-
-
Start
-
flashing
-
-
Cooling
-
flashing
-
-
Over Temperature
-
-
ON
-
Thermal Break Sensor error
-
-
-
4 blinks
Lamp Error
-
5 blinks
-
-
Burner Fan error
-
6 blinks
1 blinks
-
System Fan error
-
6 blinks
2 blinks
-
Power and Ballast Fan error
-
5 blinks
-
1 blinks
Case Open
-
7 blinks
-
-
DMD error
-
8 blinks
-
-
Color wheel error
-
9 blinks
-
-
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the Power or Lamp LEDs are still blinking or the Temp LED is lit, contact your
service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control or projector.
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Display Setings menu of the OSD.
Problem: The image is streaked
1. Set the Frequency settings on the Image Settings>Advanced menu of the OSD to the
default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
— 48 —
DLP Projector – User’s Manual
Adjust the Color Temperature and Gamma settings on the Display Settings menu of the
OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
– 49 –
DLP Projector—User’s Manual
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI
cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or
up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz
or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable
and can successfully handle 1080p signals including those at increased color depths and/or
increased refresh rates from the Source. High-Speed cables are also able to accommodate
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective
distance from the typical 10 meter range to much longer lengths. These companies
manufacture a variety of solutions that include active cables (active electronics built into
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and
fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI
Compliance Test Specification. However, there may be instances where cables bearing the
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively
investigates these instances to ensure that the HDMI trademark is properly used in the
market. We recommend that consumers buy their cables from a reputable source and a
company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
— 50 —
DLP Projector – User’s Manual
SPECIFICATIONS
Specifications
1080P 0.65”
Display type
1080P 1920x1080 Native
Resolution
Projection distance
Projection screen size
Projection lens
Zoom ratio
1.5 meters ~ 7 meters (Standard projection len)
35 to 205 inches (Standard projection len)
Manual Focus/Manual Zoom (Standard projection len)
1.25 (Standard projection len)
+/- 35 degree ( +/- 350 step )
Vertical keystone correction
Projection methods
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, Mac
SDTV/EDTV/ HDTV
480i, 480p, 720p, 1080i, 1080p
Video compatibility
NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM
H-Sync
15.6, 30 – 91.1 kHz
V-Sync
50 – 85 Hz
FCC-B, UL, CB, CE, CCC, China CECP, KC, PCT, PSB, ICES-003,
NOM, UL-S(Argentina), SASO and C-tick
5° ~ 35°C
Safety certification
Operation temperature
Dimensions
AC Input
Power consumption
431.11mm (W) x 344.16mm (D) x 161.51mm (H)
AC Universal 100 – 240, Typical @ 110VAC (100 – 240)/+-10%
Bright mode : 420W / Normal mode:360W
<0.5 watts
Stand By
330W (Boost) / 280W (STD)
Lamp
3W x 2
Audio speaker
VGA x 2
DISPLAYPORT x 1
DVI-D x 1
PC audio jack x 2
Input Terminals
S-Video x 1
Component x 1
Composite video x 1
HDMI x 1
VGA x 1
Output Terminals
PC audio jack x 1
RS-232C
Control Terminals
RJ45
Screen trigger: DC Jack x 1 (DC12V 200mA output function)
wire remote
Kensington lock
Security
– 51 –
DLP Projector—User’s Manual
Image Hight
Projection Distance vs. Projection Size (1080P)
A
Keystone Correction Angle
Projection Distance
V-Sync
Projection Distance and Size Table
Standard projection len: TR: 1.54~1.93; offset=120%
TELE
Distance (m)
WIDE
1.71
3.42
4.27
8.55
1.70
3.41
6.82
10.23
40
80
100
200
50
100
200
300
Keystone Correction
Angle (degree)
9.92
9.92
9.92
9.92
12.36
12.36
12.36
12.36
Image Height (mm)
498
996
1245
2491
623
1245
2491
3736
Image Width (mm)
886
1771
2214
4428
1107
2214
4428
6641
A (mm)
50
100
125
249
62
125
249
374
Diagonal (inch)
Long throw projection len: TR: 1.93~2.9; offset=120%
TELE
Distance (m)
WIDE
2.57
6.42
12.84
19.26
2.14/
6.41
12.82
19.23
40
100
200
300
50
150
300
450
Keystone Correction
Angle (degree)
6.64
6.64
6.64
6.64
9.92
9.92
9.92
9.92
Image Height (mm)
498
1245
2491
3736
623
1868
3736
5604
Image Width (mm)
886
2214
4428
6641
1107
3321
6641
9962
A (mm)
50
125
249
374
62
187
374
560
Diagonal (inch)
— 52 —
DLP Projector – User’s Manual
Short throw projection len: TR: 0.77; offset=120%
FIX
Distance (m)
0.68
1.36/
1.70
2.56
40
80
100
150
Keystone Correction
Angle (degree)
23.67
23.67
23.67
23.67
Image Height (mm)
498
996
1245
1868
Image Width (mm)
886
1771
2214
3321
A (mm)
50
100
125
187
Diagonal (inch)
– 53 –
DLP Projector—User’s Manual
Timing Mode Table
SIGNAL
RESOLUTION
H-SYNC
(KHZ)
V-SYNC
(HZ)
NTSC
-
15.734
60.0
O
-
PAL/SECAM
-
15.625
50.0
O
720 x 400
37.9
85.0
640 x 480
31.5
640 x 480
VESA
VIDEO /
COMPONENT RGB
S-VIDEO
DVI
HDMI /
DP
-
-
-
-
-
-
-
-
-
O
O
O
60.0
-
-
O
O
O
37.9
72.0
-
-
O
O
O
640 x 480
37.5
75.0
-
-
O
O
O
640 x 480
43.3
85.0
-
-
O
O
O
800 x 600
35.2
56.0
-
-
O
O
O
800 x 600
37.9
60.0
-
-
O
O
O
800 x 600
48.1
72.0
-
-
O
O
O
800 x 600
46.9
75.0
-
-
O
O
O
800 x 600
53.7
85.0
-
-
O
O
O
1024 x 768
48.4
60.0
-
-
O
O
O
1024 x 768
56.5
70.0
-
-
O
O
O
1024 x 768
60.0
75.0
-
-
O
O
O
1024 x 768
68.7
85.0
-
-
O
O
O
1280 x 800
49.7
59.8
-
-
O
O
O
1280 x 800
62.8
74.9
-
-
O
O
O
1280 x 800
71.6
84.8
-
-
O
O
O
1280 x 1024
63.98
60.0
-
-
O
O
O
1280 x 1024
79.98
75.0
-
-
O
O
O
1280 x 1024
91.10
85.0
-
-
O
O
O
1280 x 960
60.0
60.0
-
-
O
O
O
1280 x 960
85.9
85.0
-
-
O
O
O
1400 x 1050
65.3
60.0
-
-
O
O
O
1440 x 900
70.6
75.0
-
-
O
O
O
1440 x 900
55.6
60.0
-
-
O
O
O
— 54 —
DLP Projector – User’s Manual
SIGNAL
VESA
Apple Mac
SDTV
EDTV
HDTV
RESOLUTION
H-SYNC
(KHZ)
V-SYNC
(HZ)
VIDEO /
S-VIDEO
DVI
HDMI /
DP
1600 x 1200
75.0
60.0
-
-
O
O
O
1920 x 1080
67.5
60.0
-
-
O
O
O
1920 x 1200
74.04
59.95
-
-
O
O
O
640 x 480
35.0
66.68
-
-
O
O
O
832 x 624
49.725
74.55
-
-
O
O
O
1024 x 768
60.24
75.0
-
-
O
O
O
1152 x 870
68.68
75.06
-
-
O
O
O
480i
15.734
60.0
-
O
-
-
O
576i
15.625
50.0
-
O
-
-
O
480p
31.469
60.0
-
O
-
-
O
576p
31.25
50.0
-
O
-
-
O
720p
37.5
50.0
-
O
-
-
O
720p
45.0
60.0
-
O
-
-
O
1080i
33.8
60.0
-
O
-
-
O
1080i
28.1
50.0
-
O
-
-
O
1080p
67.5
60.0
-
O
-
-
O
1080p
56.3
50.0
-
O
-
-
O
1080p
27.0
24
-
O
-
-
O
1080p
28.13
25
-
O
-
-
O
1080p
33.75
30
-
O
-
-
O
COMPONENT RGB
O: Frequency supported
—: Frequency not supported
* : Displayable level
The resolution of the panel for the projector is 1920 x 1080. Resolution other than native resolution
may display with uneven size of text or lines.
– 55 –
DLP Projector—User’s Manual
Projector Dimensions
— 56 —
DLP Projector – User’s Manual
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, UL, CB, CE, CCC, China CECP, KC, PCT, PSB, ICES-003, NOM, UL-S(Argentina),
SASO and C-tick
– 57 –
DLP Projector—User’s Manual
APPENDIX I
RS-232C Protocol
RS232 Setting
Baud rate:
115200
Parity check:
None
Data bit:
8
Stop bit:
1
Flow Control
None
RS-232 Setup for D5180 / D5185
In the main HyperTerminal window,
1. Select “Property” from the “File” Menu
2. Select “Setting” Tab
3. Select “VT100” under Emulation
4. Click on “ASCII Setup”
5. Tick the options as below
6. Click OK while done
Control Command Structure
Header code
HEX
ASCII
‘V’
Command code
Data code
End code
Command
Data
0Dh
Command
Data
CR
— 58 —
DLP Projector – User’s Manual
Operation Command
Note:
XX=00-98, projector's ID, XX=99 is for all projectors D5180/D5185 -> V99Sxxxx
Return Result P=Pass / F=Fail
n: 0:Disable/1: Enable/Vaule(0~9999)
Command Group 00
ASCII
HEX
Function
Description
Power On
Return Result
VXXS0001
56H 39H 39H 53H 30H 30H 30H 31H 0DH
VXXS0002
56H 39H 39H 53H 30H 30H 30H 32H 0DH
Power Off
P/F
VXXS0003
56H 39H 39H 53H 30H 30H 30H 33H 0DH
Resync
P/F
VXXG0004
56H 39H 39H 47H 30H 30H 30H 34H 0DH
Get Lamp Hours
Pn/F
VXXS0006
56H 39H 39H 53H 30H 30H 30H 36H 0DH
System Reset
P/F
VXXG0007
56H 39H 39H 47H 30H 30H 30H 37H 0DH
Get System Status
VXXG0008
56H 39H 39H 47H 30H 30H 30H 38H 0DH
Get F/W Version
P/F
0: Stand by
1:Ignition
2:Normal
3:Cooling
Pn/F
Pn/F
Command Group 01
ASCII
VXXG0101
HEX
Function
Description
Return Value
56H 39H 39H 47H 30H 31H 30H 31H 0DH
Get Brightness
n=0~100
Pn/F
VXXS0101n
56H 39H 39H 53H 30H 31H 30H 31H n 0DH
Set Brightness
n=0~100
P/F
VXXG0102
56H 39H 39H 47H 30H 31H 30H 32H 0DH
Get Contrast
n=0~100
Pn/F
VXXS0102n
56H 39H 39H 53H 30H 31H 30H 32H n 0DH
Set Contrast
n=0~100
P/F
VXXG0103
56H 39H 39H 47H 30H 31H 30H 33H 0DH
Get Color
n=0~512
Pn/F
VXXS0103n
56H 39H 39H 53H 30H 31H 30H 33H n 0DH
Set Color
n=0~512
P/F
VXXG0104
56H 39H 39H 47H 30H 31H 30H 34H 0DH
Get Tint
n=0~100
Pn/F
VXXS0104n
56H 39H 39H 53H 30H 31H 30H 34H n 0DH
Set Tint
n=0~100
P/F
VXXG0105
56H 39H 39H 47H 30H 31H 30H 35H 0DH
Get Sharpness
0~24
Pn/F
VXXS0105n
56H 39H 39H 53H 30H 31H 30H 35H n 0DH
Set Sharpness
VXXG0106
56H 39H 39H 47H 30H 31H 30H 36H 0DH
VXXS0106n
56H 39H 39H 53H 30H 31H 30H 36H n 0DH
VXXG0107
56H 39H 39H 47H 30H 31H 30H 37H 0DH
Get Gamma
0~10
Pn/F
VXXS0107n
56H 39H 39H 53H 30H 31H 30H 37H n 0DH
Set Gamma
0~10
P/F
– 59 –
0~24
0:Native
1:Warm
2:Normal
Get Color Temperature 3.Cool
4.Cooler
5.High Cool
0:Native
1:Warm
2:Normal
Set Color Temperature 3.Cool
4.Cooler
5.High Cool
P/F
Pn/F
P/F
DLP Projector—User’s Manual
Command Group 01
ASCII
HEX
Function
Description
Return Value
0:Movie
1:Bright
VXXG0108n
56H 39H 39H 47H 30H 31H 30H 38H 0DH
Get Picture Mode
2:Normal
3.User1
P/F
4.User2
5.User3
0:Movie
1:Bright
VXXS0108n
56H 39H 39H 53H 30H 31H 30H 38H n 0DH
Set Picture Mode
2:Normal
3.User1
P/F
4.User2
5.User3
Command Group 02
ASCII
HEX
Function
Description
Return Value
VXXS0201
56H 39H 39H 53H 30H 32H 30H 31H 0DH
Select RGB
P/F
VXXS0202
56H 39H 39H 53H 30H 32H 30H 32H 0DH
Select RGB2
P/F
VXXS0203
56H 39H 39H 53H 30H 32H 30H 33H 0DH
Select DVI
P/F
VXXS0204
56H 39H 39H 53H 30H 32H 30H 34H 0DH
Select Video
P/F
VXXS0205
56H 39H 39H 53H 30H 32H 30H 35H 0DH
Select S-Video
P/F
VXXS0206
56H 39H 39H 53H 30H 32H 30H 36H 0DH
Select HDMI 1
P/F
VXXS0208
56H 39H 39H 53H 30H 32H 30H 38H 0DH
Select Component
P/F
VXXS0209
56H 39H 39H 53H 30H 32H 30H 39H 0DH
Select DP
VXXG0220
56H 39H 39H 47H 30H 32H 32H 30H 0DH
Get Current Source
P/F
Return
1:RGB
2:RGB2
3:DVI
4:Video
5:S-Video
6:HDMI
8:Component
9:DP
Pn/F
Command Group 03
ASCII
HEX
Function
VXXG0301
56H 39H 39H 47H 30H 33H 30H 31H 0DH
Get Scaling
VXXS0301n
56H 39H 39H 53H 30H 33H 30H 31H n 0DH
Set Scaling
VXXG0302
VXXS0302n
VXXG0304
VXXS0304n
56H 39H 39H 47H 30H 33H 30H 32H 0DH
56H 39H 39H 53H 30H 33H 30H 32H n 0DH
56H 39H 39H 47H 30H 33H 30H 34H 0DH
56H 39H 39H 53H 30H 33H 30H 34H n 0DH
Blank
Blank
Freeze On
Freeze On
— 60 —
Description
0: Auto
1: 16:9
2: 4:3
3: Letter Box
4: Real
0: Auto
1: 16:9
2: 4:3
3: Letter Box
4: Real
Return Value
Pn/F
P/F
Pn/F
P/F
Pn/F
P/F
DLP Projector – User’s Manual
Command Group 03
ASCII
HEX
Function
VXXG0305
VXXS0305n
56H 39H 39H 47H 30H 33H 30H 35H 0DH
56H 39H 39H 53H 30H 33H 30H 35H n 0DH
Get Volume
Set Volume
VXXG0308
56H 39H 39H 47H 30H 33H 30H 38H 0DH
Projection Mode
Description
Return Value
n=0~10
Pn/F
n=0~10
P/F
0:Front
1:Front+Ceiling
Pn/F
2:Rear
3:Rear+Ceiling
VXXS0308n
56H 39H 39H 53H 30H 33H 30H 38H n 0DH
Projection Mode
0:Front
1:Front+Ceiling
P/F
2:Rear
3:Rear+Ceiling
VXXG0309
56H 39H 39H 47H 30H 33H 30H 39H 0DH
Get vertical keystone value
n= -300~300
Pn/F
VXXS0309n
56H 39H 39H 53H 30H 33H 30H 39H n 0DH
Set vertical keystone value
n= -300~300
P/F
VXXG0310
VXXS0310n
56H 39H 39H 47H 30H 33H 31H 30H 0DH
56H 39H 39H 53H 30H 33H 31H 30H n 0DH
Get horizontal keystone value
Set horizontal keystone value
n=-350~350
n=-350~350
Pn/F
P/F
Command Group 04 (Remote Control)
ASCII
HEX
Function
Description
Return Value
VXXS0401
VXXS0402
VXXS0403
VXXS0404
VXXS0405
VXXS0408
VXXS0409
VXXS0410
VXXS0411
VXXS0412
VXXS0413
VXXS0416
VXXS0417
VXXS0418
VXXS0419
56H 39H 39H 53H 30H 34H 30H 31H 0DH
56H 39H 39H 53H 30H 34H 30H 32H 0DH
56H 39H 39H 53H 30H 34H 30H 33H 0DH
56H 39H 39H 53H 30H 34H 30H 34H 0DH
56H 39H 39H 53H 30H 34H 30H 35H 0DH
56H 39H 39H 53H 30H 34H 30H 38H 0DH
56H 39H 39H 53H 30H 34H 30H 39H 0DH
56H 39H 39H 53H 30H 34H 31H 30H 0DH
56H 39H 39H 53H 30H 34H 31H 31H 0DH
56H 39H 39H 53H 30H 34H 31H 32H 0DH
56H 39H 39H 53H 30H 34H 31H 33H 0DH
56H 39H 39H 53H 30H 34H 31H 36H 0DH
56H 39H 39H 53H 30H 34H 31H 37H 0DH
56H 39H 39H 53H 30H 34H 31H 38H 0DH
56H 39H 39H 53H 30H 34H 31H 39H 0DH
UP arrow
DOWN arrow
LEFT arrow
RIGHT arrow
POWER
AUTO
KEYSTONE+
KEYSTONEMENU
STATUS
MUTE
BLANK
FREEZE
VOLUME+
VOLUME-
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
P/F
VXXS0420
56H 39H 39H 53H 30H 34H 32H 30H 0DH
Enter
P/F
– 61 –
DLP Projector—User’s Manual
APPENDIX II
The D5180HD family include the following models
D5I80HD
D5I8ZHDA
D5I8ZHDB
D5I8ZHDC
D5I8ZHDD
D5I8ZHDE
D5I8ZHDF
D5I8ZHDG
D5I8ZHDH
D5I8ZHDI
D5I8ZHDJ
D5I8ZHDK
D5I8ZHDL
D5I8ZHDM
D5I8ZHDN
D5I8ZHDO
— 62 —
DLP Projector – User’s Manual
APPENDIX III
D5185HD Edge Blending
Equipment Requirement
1.
Display Units:two D5185HD projectors recommended to have similar brightness levels or closed lamp
hour used.
2.
Source Input:a personal computer (PC) with Intel® Core™ i7 processor with 4GB Memory and Windows® 7 (32/64 bit) with dual DVI / HDMI / DP ports.
3.
Graphic Card:Matrox (M-series) or nVidia video card with build-in Edge Overlap function
4.
Optical tool:CL200 for color and brightness measurement
Edge Blending Guideline
1.
Ensure the blended units with similar brightness level to prevent defect in overlapping area
2.
Mechanically blend two screens with assistance of test pattern “Crosshatch” by moving the projector position and/or by adjusting the lens shift feature.
3.
Enable the edge blending function (e.g., Mosaic for nVidia) in the PC, and specify the overlapping area
(15~25% of native resolution)
4.
Projector Setup 1:the Display Mode = User3
– 63 –
DLP Projector—User’s Manual
5.
Projector Setup 2:Advance Setup page, entry Alignment
6.
Projector Setup 3:Alignment Status = ON
— 64 —
DLP Projector – User’s Manual
7.
Projector Setup 4:Enter Warp and fine tune the screens by the Warp functions
8.
Projector Setup 5:Enter Blending and fine tune the screen by the Blending functions
9.
Projector Setup 6:minimize the brightness difference between the two projectors by adjusting the While
Level / Black Level / Lamp Power functions
– 65 –
DLP Projector—User’s Manual
10.
Projector Setup 7:cut off unnecessary part by using the Blanking function
11.
Open up a picture to verify the blending status and repeat the above steps if necessary.
— 66 —