Base Units Base Unit Prices

Base Units Base Unit Prices
Prices as of April 15, 2015. Check Web site for most current prices.
Base Units
Company
Information
Control Systems
Overview
To use the Do-more H2 Series PLC, you must have at least one base unit. A base unit
has an internal power supply that converts the input power (110-220VAC, 24VDC or
125VDC) to 5VDC in order to activate the modules installed in the base unit. For the
Do-more H2 Series PLC, 10 types of base units are available.
D2-03B-1$132.00
D2-04B-1$143.00
D2-06B-1$176.00
Base Unit Part Numbers
Number of Module Slots
Base Unit Prices
D2-09B-1$220.00
D2-03BDC1-1$150.00
Input Power Type
D2-04BDC1-1$171.00
110-220 VAC
24 VDC
125 VDC
D2-03B-1
D2-03BDC1-1
-
D2-04B-1
D2-04BDC1-1
-
D2-06B-1
D2-06BDC1-1
D2-06BDC2-1
D2-06BDC2-1$184.00
D2-09B-1
D2-09BDC1-1
D2-09BDC2-1
D2-09BDC2-1$238.00
3 slot
4 slot
6 slot
9 slot
D2-06BDC1-1$194.00
D2-09BDC1-1$238.00
CLICK PLC
Do-More
PLCs Overview
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL105
DirectLOGIC
DL205
In the base unit, the far left slot is called the ‘CPU Slot’. It is used for a CPU or base
controller. Optional modules (discrete I/O modules, analog I/O modules, and specialty
modules) can be installed in the other slots. For instance, if you pick a base unit with nine
slots, you can install up to eight optional modules.
DirectLOGIC
DL305
DirectLOGIC
DL405
Module Slots are numbered from left to right starting with zero. The slot to the right of
the CPU slot is Slot 0, the slot to the right of it is Slot 1 and so on. The following is an
example with the nine slot base unit D2-09B-1.
Productivity
Controller
Overview
Productivity
3000
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Other HMI
Communications
The following is a detailed specification table for the base units.
Appendix
Book 1
Power Supply Specifications
Specification
Part Numbers
AC Powered Bases
D2-03B-1, D2-04B-1,
D2-06B-1, D2-09B-1
24 VDC Powered Bases
D2-03BDC1-1, D2-04BDC1-1,
D2-06BDC1-1, D2-09BDC1-1
Terms and
Conditions
125 VDC Powered Bases
D2-06BDC2-1,
D2-09BDC2-1
Voltage Withstand (dielectric) 1 minute @ 1,500 VAC between primary, secondary, field ground, and run relay
Insulation Resistance
> 10 Mq at 500 VDC
Input Voltage Range
85-132 VAC (110 range)
170-264 VAC ( 220 range)
47-63 Hz
10.2-28.8 VDC (24 VDC)
with less than 10% ripple
Auxiliary 24 VDC Output
300 mA max.
none
300 mA max.
Maximum Inrush Current
30A
10A
20A
Maximum Power
80 VA
25W
30W
100-264 VDC (125 VDC)
with less than 10% ripple
Book 1 (14.2)
www.automationdirect.com/do-more-plcs
Do-more H2 PLCs
eDH-25
Prices as of April 15, 2015. Check Web site for most current prices.
Base Units
I/O Expansion
When you need to use more than eight optional modules or you need to install base units in isolated locations,
the Do-more H2 Series PLC supports the Ethernet Remote I/O System.
H2-ERM(100)
Stride Ethernet Switch
(See the Communications
Products section for details.)
H2-EBC100 I/O
H4-EBC I/O
T1H-EBC100 I/O
Note for DL205 PLC customers
The Do-more H2 Series PLC does NOT support local expansion I/O with the D2-EM/D2-CM or serial remote
I/O with the D2-RMSM.
Book 1 (14.2)
eDH-26
Do-more H2 PLCs
1-800-633-0405
Prices as of April 15, 2015. Check Web site for most current prices.
Base Units
Company
Information
Control Systems
Overview
Module Placement and
I/O Usage Tables
There are very few I/O module placement restrictions with the Do-more H2
Series PLC family. In general, any mix of
analog and discrete module types can be
used in any local or Ethernet remote base.
However, specialty modules can’t be
used in the Ethernet remote base except
for the F2-08SIM. Reference the Module
Placement Restrictions table to the right
for the Do-more H2 Series PLC.
Analog I/O in the Ethernet remote
bases
When using an analog module in an
Ethernet remote base, the analog update
time to the CPU will be asynchronous to
the scan time. Critical analog I/O should
be located in the local base.
I/O point usage
The table to the right indicates the number
of I/O points consumed by each module.
Use this information to ensure you stay
within the maximum I/O count of the I/O
system you have chosen.
CLICK PLC
Module Placement Restrictions
Do-More
PLCs Overview
Module/Unit
Local CPU Base
Ethernet Remote Base
CPUs
Discrete I/O
Analog I/O
CPU slot only
3
3
3
3
Do-More T1H
PLC
CPU slot only
DirectLOGIC
PLCs Overview
Base Controller
H2-EBC100
Specialty Modules
H2-CTRIO
H2-CTRIO2
H2-ECOM100
H2-SERIO
H2-SERIO-4
H2-ERM(100)
F2-08SIM
Do-More H2
PLC
DirectLOGIC
DL05/06
3
3
3
3
3
3
3
DirectLOGIC
DL105
DirectLOGIC
DL205
3
DirectLOGIC
DL305
I/O Module Point Usage
DC INPUT
RELAY OUTPUT
D2-08ND3
D2-16ND3-2
D2-32ND3
D2-32ND3-2
8X
16 X
32 X
32 X
D2-04TRS
D2-08TR
F2-08TR
F2-08TRS
D2-12TR
8 Y1
8Y
8Y
8Y
16 Y2
AC INPUT
D2-08NA-1
D2-08NA-2
D2-16NA
8X
8X
16 X
DC OUTPUT
D2-04TD1
D2-08TD1
D2-08TD2
D2-16TD1-2
D2-16TD2-2
F2-16TD1P
F2-16TD2P
D2-32TD1
D2-32TD2
F2-08SIM
H2-CTRIO
H2-CTRIO2
H2-EBC100
H2-ECOM100
H2-ERM(100)
H2-SERIO
H2-SERIO-4
8X
None
None
None
None
None
None
None
Productivity
Controller
Overview
Productivity
3000
Universal
Field I/O
COMBINATION
D2-08CDR
Software
8 X/8 Y1
C-More
HMI
ANALOG
8 Y1
8Y
8Y
16 Y
16 Y
16 X/16 Y
16 X/16 Y
32 Y
32 Y
AC OUTPUT
D2-08TA
F2-08TA
D2-12TA
DirectLOGIC
DL405
SPECIALTY MODULES
8Y
8Y
16 Y2
F2-04AD-1
F2-04AD-2
F2-08AD-1
F2-08AD-2
F2-02DA-1(L)
F2-02DA-2(L)
F2-4AD2DA
F2-8AD4DA-1
F2-8AD4DA-2
F2-02DAS-1
F2-02DAS-2
F2-08DA-1
F2-08DA-2
F2-04RTD
F2-04THM
C-More Micro
HMI
8 X/4 WX
8 X/4 WX
8 X/8 WX
8 X/8 WX
2 WY
2 WY
8 X/4 WX/2 WY
8 X/8 WX/7 WY
8 X/8 WX/7 WY
2 WY
2 WY
8 WY
8 WY
8 X/4 WX
8 X/4 WX
ViewMarq
Industrial
Marquees
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
Note 1: 4-pt. modules consume eight points. Only the first four points are used.
Note 2: 12-pt. modules consume 16 points. The first six points are assigned, two are skipped,
and then the next six points are assigned. For example, a D2-12TA installed in slot 0
would use Y0-Y5, and Y8-Y13. Y6-Y7, and Y14-Y15 would be unused.
Book 1 (14.2)
www.automationdirect.com/do-more-plcs
Do-more H2 PLCs
eDH-27
Prices as of April 15, 2015. Check Web site for most current prices.
Base Units
Power Budget
When determining the types and quantity
of I/O modules you will be using, it is
important to remember there is a defined
amount of power available from the base
power supply.
The chart on the next page indicates
the power supplied and used by each
module. The adjacent chart shows an
example of how to calculate the power
used by your particular system. These
charts should make it easy for you to
determine if the devices you have chosen
will operate within the power budget of
your system configuration.
If the I/O you have chosen for a base
exceeds the maximum power available
from the power supply, you may be able
to resolve the problem by using remote
I/O bases.
1.Using a chart similar to the one below,
fill in column 2.
2.
Using the tables on the next page,
enter the current supplied and used
by each device (columns 3 and 4).
Devices which fall into the “Other”
category (Row D) are devices such as
the operator interface and the handheld programmer, which also have
power requirements, but do not directly
plug into the base.
3.
Add the current used by the system
devices (columns 3 and 4) starting
with the CPU slot and put the total in
the row labeled “Maximum Current
Required” (Row E).
Column 1
A
Base power supply specifications
The table below lists base power supply
specifications, including maximum inrush
current and maximum power consumed
from your power source.
Power budget example
The example on the right shows how
to calculate the power budget for the
Do-more PLC system. The examples are
constructed around a single 9-slot base
using the devices shown. It is recommended you construct a similar table for
your Do-more PLC system. Follow the
steps to the right to determine your power
budget.
4.
Subtract the row labeled “Maximum
Current Required” (Row E), from the
row labeled “Current Supplied” (Row
B). Place the difference in the row
labeled “Remaining Current Available”
(Row F).
5.
If “Maximum Current Required” is
greater than “Current Supplied” in
either column 3 or 4, the power
budget will be exceeded. It will be
unsafe to use this configuration, and
you will need to restructure your I/O
configuration. Note the auxiliary power
supply does not need to supply all the
external power. If you need more than
the 300mA supplied, you can add
an external 24V power supply. This
will help keep you within your power
budget for external power.
Column 2
Column 3
Column 4
Device Type
5VDC (mA)
External Power 24
VDC (mA)
9 slot
2,600
300
H2-DM1E
D2-16ND3-2
D2-16ND3-2
D2-16NA
D2-08NA-1
D2-16TD1-2
D2-08TA
D2-08TA
275
100
100
100
50
200
250
250
0
0
0
0
0
80
0
0
EA1-S3ML
90
0
E Maximum Current Required
1415
80
F Remaining Current Available
2600-1415=1185
300-80=220
B CURRENT SUPPLIED
Base
C CURRENT REQUIRED
CPU SLOT
SLOT 0
SLOT 1
SLOT 2
SLOT 3
SLOT 4
SLOT 5
SLOT 6
SLOT 7
D OTHER
Operator interface
Power Supply Specifications
Specification
Part Numbers
AC Powered Bases
D2-03B-1, D2-04B-1, D2-06B-1, D2-09B-1
24 VDC Powered Bases
D2-03BDC1-1, D2-04BDC1-1,
D2-06BDC1-1, D2-09BDC1-1
125 VDC Powered Bases
D2-06BDC2-1, D2-09BDC2-1
Voltage Withstand (dielectric) 1 minute @ 1,500 VAC between primary, secondary, field ground, and run relay
Insulation Resistance
> 10 Mq at 500 VDC
Input Voltage Range
85-132 VAC (110 range)
170-264 VAC ( 220 range)
47-63 Hz
10.2-28.8 VDC (24 VDC)
with less than 10% ripple
Auxiliary 24 VDC Output
300 mA max.
none
300 mA max.
Maximum Inrush Current
30A
10A
20A
Maximum Power
80 VA
25W
30W
100-264 VDC (125 VDC)
with less than 10% ripple
Book 1 (14.2)
eDH-28
Do-more H2 PLCs
1-800-633-0405
Prices as of April 15, 2015. Check Web site for most current prices.
Base Units
Company
Information
Control Systems
Overview
Power Requirements
This section shows the amount of power
supplied by each of the base power
supplies and the amount of power
consumed by each module. The Power
Consumed charts list how much INTERNAL
power from each power source is required
for the modules. Use this information
when calculating the power budget for
your system.
In addition to the internal power sources,
bases offer a 24 VDC auxiliary power
supply with external power connections.
This auxiliary power supply can power
external devices.
Use ZipLinks to reduce power
requirements
If your application requires a lot of relay
outputs, consider using the ZIPLink AC or
DC relay output modules ZL-RRL16-24-1
or ZL-RRL16-24-2. These modules can
switch high current (10A) loads without
putting a heavy load on your base power
budget. Refer to the Terminal Blocks and
Wiring Solutions section in this catalog for
more information.
This logo is placed next to the I/O
modules that are supported by the ZIPLink
connection systems. See the I/O module
specifications at the end
of this section.
CLICK PLC
Power Supplied
Device
5V(mA)
24V Auxiliary
Do-More
PLCs Overview
D2-04BDC1-1
2600
None
Do-More H2
PLC
300
D2-06BDC1-1
2600
None
300
D2-09BDC1-1
2600
None
2600
300
D2-06BDC2-1
2600
300
2600
None
D2-09BDC2-1
2600
300
5V(mA)
24V Auxiliary
D2-03B-1
2600
300
D2-04B-1
2600
D2-06B-1
2600
D2-09B-1
D2-03BDC1-1
Bases
Device
Bases
Device
DirectLOGIC
PLCs Overview
Power Consumed
Power Consumed
Device
DirectLOGIC
DL105
100
5
DirectLOGIC
DL205
F2-04AD-2
110
5
F2-08AD-1
100
5
24V Auxiliary
H2-DM1
250
0
F2-04AD-1
H2-DM1E
275
0
Analog Modules
CPUs
DC Input Modules
D2-08ND3
50
0
F2-08AD-2
100
5
D2-16ND3-2
100
0
F2-02DA-1
40
60 (note 1)
D2-32ND3
25
0
F2-02DA-1L
40
70 @ 12V (note 1)
0
F2-02DA-2
40
60
F2-02DA-2L
F2-02DAS-1
40
100
70 @ 12V
50 / channel
D2-32ND3-2
25
AC Input Modules
D2-08NA-1
50
0
D2-08NA-2
100
0
F2-02DAS-2
100
60 / channel
D2-16NA
100
0
F2-08DA-1
30
50 (note 1)
DC Output Modules
F2-08DA-2
60
140
D2-04TD1
60
20
F2-4AD2DA
60
80 (note 1)
D2-08TD1
100
0
F2-8AD4DA-1
35
100 (note 1)
D2-08TD2
100
0
F2-8AD4DA-2
35
80 (note 1)
D2-16TD1-2
200
80
F2-04RTD
90
0
D2-16TD2-2
200
0
F2-04THM
110
60
F2-16TD1P
70
50
Specialty Modules
F2-16TD2P
70
50
H2-CTRIO
400
0
D2-32TD1
350
0
H2-CTRIO2
275
0
D2-32TD2
350
0
H2-EBC100
300
0
AC Output Modules
H2-ECOM100
300
0
D2-08TA
250
0
H2-ERM
320
0
F2-08TA
250
0
H2-ERM100
300
0
D2-12TA
350
0
H2-SERIO
80
0
H2-SERIO-4
80
0
50
0
Relay Output Modules
D2-04TRS
250
0
F2-08SIM
D2-08TR
250
0
Note 1: Add an additional 20 mA per output loop.
F2-08TR
670
0
F2-08TRS
670
0
D2-12TR
450
0
Combination In/Out Module
D2-08CDR
200
0
Book 1 (14.2)
www.automationdirect.com/do-more-plcs
DirectLOGIC
DL05/06
24V Auxiliary
5V(mA)
5V(mA)
Do-More T1H
PLC
Do-more H2 PLCs
eDH-29
DirectLOGIC
DL305
DirectLOGIC
DL405
Productivity
Controller
Overview
Productivity
3000
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
Prices as of April 15, 2015. Check Web site for most current prices.
Do-more H2 Series PLC Overview
Module Compatibility
The following table shows which DL205 components are supported by the H2-DM1 and
H2-DM1E Do-more CPUs.
Module
Base Units
Module Compatibility Table
Status
Module
Part Number
F2-04AD-1
D2-04B-1
F2-04AD-2
D2-06B-1
F2-08AD-1
D2-09B-1
F2-08AD-2
D2-03BDC1-1
F2-04RTD
D2-04BDC1-1
F2-04THM
D2-06BDC1-1
Analog I/O
Modules
D2-09BDC1-1
D2-06BDC2-1
F2-02DA-2(L)
F2-02DAS-1
F2-02DAS-2
D2-08ND3
F2-08DA-1
D2-16ND3-2
F2-08DA-2
D2-32ND3
F2-4AD2DA
D2-32ND3-2
F2-8AD4DA-1
D2-08NA-1
F2-8AD4DA-2
Local Expansion D2-CM
Modules
D2-EM
D2-16NA
Status
F2-02DA-1(L)
D2-09BDC2-1
D2-08NA-2
Discrete I/O
Modules
Part Number
D2-03B-1
No
No
D2-04TD1
H2-ERM(100)
D2-08TD1
H2-ERM-F
D2-08TD2
D2-RMSM
No
D2-16TD1-2
D2-RSSS
No
D2-16TD2-2
H2-ECOM100
F2-16TD1P
H2-ECOM-F
F2-16TD2P
D2-DCM
D2-32TD1
Specialty
Modules
D2-32TD2
H2-EBC-F
D2-08TA
H2-SERIO
F2-08TA
H2-SERIO-4
D2-12TA
F2-CP128
D2-04TRS
H2-CTRIO
D2-08TR
H2-CTRIO2
F2-08TR
D2-CTRINT
F2-08TRS
F2-08SIM
Programmer
Operator
Interface
D2-12TR
D2-08CDR
= Supported
No
H2-EBC100
No
No
D2-HPP
No
DV-1000
No
No = Not Supported
Book 1 (14.2)
eDH-10
Do-more H2 PLCs
1-800-633-0405
Prices as of April 15, 2015. Check Web site for most current prices.
Do-more H2 Series PLC Overview
Company
Information
Control Systems
Overview
CLICK PLC
Communications
Do-More
PLCs Overview
The Do-more H2 Series PLC supports many communication protocols. The following table shows which CPU module
communications port or specialty module supports each protocol.
CPU Modules
Protocols
Do-more Designer Programming
H2-DM1 / H2-DM1E
RS-232
USB Port
Serial Port
Yes
Yes
Do-More H2
PLC
Do-More T1H
PLC
Specialty Modules
H2-DM1E
H2-ECOM100 H2-SERIO
Ethernet H2-ECOM100
H2-ECOM-F H2-SERIO-4
Port
Yes
Yes
H2-ERM100
H2-ERM-F
DirectLOGIC
PLCs Overview
Yes
DirectLOGIC
DL05/06
Modbus/RTU Client (Master)
Yes
Yes
DirectLOGIC
DL105
Modbus/RTU Server (Slave)
Yes
Yes
DirectLOGIC
DL205
Modbus/TCP Client (Master)
Yes
Yes
Modbus/TCP Server (Slave)
Yes
Yes
DirectLOGIC RX/WX Client (Master)
Yes
Yes
Yes
DirectLOGIC RX/WX Server (Slave)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
K-Sequence Server (Slave)
Yes
DirectNET Server (Slave)
HEI Ethernet Remote I/O Master
DirectLOGIC
DL405
Productivity
Controller
Overview
Yes
Productivity
3000
Universal
Field I/O
Yes
SMTP (EMail) Client
w/Authentication
Simple Network Time Protocol
(SNTP) Client
Yes
Yes
C-More Micro
HMI
Yes
Do-more Time Synchronization
Protocol (Client, Server, Alternate
Client)
Yes
Do-more Logger/UDP
Yes
Software
C-More
HMI
Yes
Do-more/PEERLINK
Serial ad-hoc ASCII/Binary
Programatic Control
DirectLOGIC
DL305
ViewMarq
Industrial
Marquees
Other HMI
Yes
Communications
Yes
UDP ad-hoc Programmatic Control
Yes
TCP Client Programmatic Control
Yes
TCP Server Programmatic Control
Yes
Appendix
Book 1
Terms and
Conditions
Blank = Not Supported
Book 1 (14.2)
www.automationdirect.com/do-more-plcs
Do-more H2 PLCs
eDH-11
Prices as of April 15, 2015. Check Web site for most current prices.
Dimensions and Installation
Company
Information
Control Systems
Overview
CLICK PLC
Understanding the installation requirements for your Do-more H2 Series PLC
system will help ensure that the components operate within their environmental
and electrical limits.
See the
Enclosures section
for an enclosure that may
be suitable for your
application
2"
50.8mm
minimum
Plan for safety
RUN
2""
2
50.8mm
8
m
minimum
TERM
STOP
USB
PGM
PORT
RS-232
SERIAL
E
1 T
0 H
/ E
1 R
0 N
0 E
T
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
1.2"
30mm
minimum
DirectLOGIC
DL105
DirectLOGIC
DL205
Environmental
specifications
DirectLOGIC
DL305
DirectLOGIC
DL405
The Environmental Specifications table
at the right lists specifications that apply
globally to the Do-more H2 Series PLC
system (CPUs, bases, and I/O modules).
Be sure that the system is operated within
these environmental specifications.
Productivity
Controller
Overview
Environmental Specification
-4 F - 158 F (-20 C to 70 C)
Ambient Operating Temperature
32oF - 131oF (0oC to 55oC)
Ambient Humidity
30%-95% relative humidity (non-condensing)
Vibration Resistance
MIL STD 810C, Method 514.2
Shock Resistance
MIL STD 810C, Method 516.2
Noise Immunity
NEMA (ICS3-304)
Atmosphere
No corrosive gases
A
(Base Total Width)
Base
3-slot
4-slot
6-slot
9-slot
Software
C-More
HMI
C-More Micro
HMI
C
(Component Width)
Millimeters Inches
Millimeters
172mm
203mm
265mm
358mm
163mm
194mm
256mm
349mm
148mm
179mm
241mm
334mm
6.41”
7.63”
10.07”
13.74”
5.8”
7.04”
9.48”
13.14”
A
4 or 8pt. I/O
2.95”
(75mm)
4 or 8pt. I/O
STOP
C
TERM
STOP
E
1 T
0 H
/ E
1 R
0 N
0 E
T
H2-DM1E
TERM
2.99”
(76mm)
STOP
RS-232
SERIAL
E
1 T
0 H
/ E
1 R
0 N
0 E
T
B
4.76"
(121mm)
TERM
5.85”
(148mm)
RUN
H2-DM1E
7.91"
(201mm)
D2-DSCBL-1
Approximate
Dimension
STOP
STOP
ZL-D24-CBL40-X
ZipLink cable
RUN
USB
PGM
PORT
E
1 T
0 H
/ E
1 R
0 N
0 E
T
USB
PGM
PORT
0 N
0 E
T
E
1 T
0 H
/ E
1 R
H2-DM1E
RUN
TERM
RUN
USB
PGM
PORT
RS-232
SERIAL
H2-DM1E
Universal
Field I/O
Millimeters Inches
ZL-D24-CBL40
ZipLink cable
E
1 T
0 H
/ E
1 R
0 N
0 E
T
o
6.77”
7.99”
10.43”
14.09”
TERM
RUN
USB
PGM
PORT
o
Inches
3.54”
(90mm)
w
OK
o
B
(Mounting Hole)
3.62”
(92mm)
12 or 16pt. I/O
RS-232
SERIAL
OK
Storage Temperature
USB
PGM
PORT
Use the diagrams below to make sure
the Do-more H2 Series PLC system can
be installed in your application. To ensure
proper airflow for cooling purposes,
bases must be mounted horizontally. It
is important to check these dimensions
against the conditions required for your
application. For example, it is recommended that approximately 3” of space is
left in front PLC surface for ease of access
and cable clearances. Also, check the
installation guidelines for recommended
cabinet clearances.
Productivity
3000
Rating
o
RS-232
SERIAL
Base dimensions
and mounting
RS-232
SERIAL
Do-More H2
PLC
Do-More T1H
PLC
This catalog should never be used as a
replacement for the user manual. The user
manual, H2-DM-M (sold separately or
downloadable online), contains important
safety information that must be followed.
The system installation should comply with
all appropriate electrical codes and standards.
H2-DM1E
Do-More
PLCs Overview
Airflow
Ai
fl
3.62”
(92mm)
Book 1 (14.2)
www.automationdirect.com/do-more-plcs
Do-more H2 PLCs
eDH-41
ViewMarq
Industrial
Marquees
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
2.95”
(75mm)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement