Craftsman | 26302 - Professional 20 Volt Lithium-Ion | Operator`s manual | Craftsman 26302 - Professional 20 Volt Lithium-Ion Operator`s manual

Operator's
Manual
LITHIUlVi=ION
CORDLESS
1/2-in. Drill/Driver
Model No.
320.26302
320.29032
320.29036
,WARRANTY
,SAFETY
• ASSEMBLY
= DESCRIPTION
=OPERATION
=MAINTENANCE
,_
WARNING:
To reduce the risk
of injury, the user must read and
understand the operator's manual
before using this product.
CHARGE BATTERY
BEFORE FIRST USE
Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA
Visit the Craftsman web page: www.sears.com/craftsman
Save this manual
for future
reference
[]
Warranty ......................................................................................................................................
2
[]
Introduction
2
[]
Safety Symbols ........................................................................................................................
3-4
[]
General Safety Rules ...............................................................................................................
5-7
[]
Specific Safety Rules ..................................................................................................................
[]
Safety Rules for Charger/Adapter
[]
Description ............................................................................................................................
[]
Assembly ....................................................................................................................................
[]
Operation ..............................................................................................................................
12-21
[]
Maintenance .........................................................................................................................
22-23
[]
Exploded View and Parts List ..............................................................................................
24-32
[]
Sears Repair Parts Phone Numbers ..........................................................................
.................................................................................................................................
TWO YEAR LIMITED WARRANTY
7
..........................................................................................
ON CRAFTSMAN
® PROFESSIONAL
8-9
10-11
11
Back Cover
TOOL
If this Craftsman Professional tool fails due to a defect in material or workmanship, RETURN
IT TO THE NEAREST SEARS STORE OR OTHER CRAFTSMAN OUTLET IN THE UNITED
STATES for free replacement during the first year from the date of purchase,
during the second year from the date of purchase.
This warranty
does not include expendable
parts such as lamps, batteries,
and for free repair
bits or blades.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
Sears,
Roebuck
and Co., Hoffman
Estates, IL 60179
SAVE THESE iNSTRUCTiONS!
READ ALL iNSTRUCTiONS)
This Drill/Driver has many features for making its use more pleasant and enjoyable. Safety,
performance and dependability
have been given top priority in the design of this product making
it easy to maintain and operate.
A
• L WARNING:
known
ductive
Some
to the state
harm.
dust
created
of California
by using
to cause
power
cancer
tools
and
contains
birth
defects
chemicals
or other
repro-
Thepurpose
ofsafety
symbols
istoattract
yourattention
topossible
dangers.
Thesafety
symbols
andtheexplanations
withthemdeserve
yourcareful
attention
andunderstanding.
The
symbol
warnings
DONOT
bythemselves
eliminate
anydanger.
Theinstructions
andwarnings
theygivearenosubstitutes
forproper
accident
prevention
measures.
_'t_WABN|NG:
BE SURE to read and understand all safety alert symbols such as
i
"DANGER", "WARNING" and "CAUTION" BEFORE using this product. Failure to follow
instructions may result in electric shock, fire and/or serious personal injury,
SYMBOL
all
SIGNAL
MEANING
DANGER:
situation,
if not avoided,
will result
Indicates which,
an imminently
hazardous
in death or serious injury.
_t
WARNING:
situation,
if not avoided,
Indicates which,
a potentially
hazardous could
result in death or serious injury.
,_
CAUTION:
situation,
if not avoided,
Indicates which,
a potentially
hazardous may result
in minor or moderate injury.
J
(Without Safety Alert Symbol) Indicates
a situation that may result in property
damage.
CAUTION:
_,WABN|NG:
To ensure safety and reliability, all repairs should
qualified service technician at Sears Service Center,
be performed
by a
]
J
m
O
&,WARNING:
The operation of any power tool can result in foreign objects
being thrown into your eyes, which can result in severe eye damage. Before
beginning power tool operation, always wear safety goggles or safety glasses
with side shields and a full face shield when needed. We recommend Wide
Vision Safety Mask for use over eyeglasses or standard safety glasses with side
shields. Always use eye protection
SAVE
THESE
which is marked to comply with ANSI Z87.1.
iNSTRUCTiONS
I
I
I
I
Some of these following symbols may be used on this tool. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL
NAME
DES|G NAT|ON/EXPLANAT|ON
V
Volts
Voltage
A
Amperes
Current
Hz
Hertz
Frequency (cycles per second)
W
Watt
Power
min
Minutes
Alternating
Time
Current
Type of current
Direct Current
no
]
.../rain
No Load Speed
O
Rotational
Class II Construction
of current
speed, at no load
Double-insulated
Per Minute
Wet Conditions
i_
Type or a characteristic
construction
Revolutions, strokes, surface
orbits, etc., per minute
locations.
Do not expose to rain or use in damp
Alert
Read The Operator's
speed,
Manual
read and understand operator's manual
To reduce the risk of injury, user must
before using this product.
Eye Protection
glasses with side shields and a full face
Always wear safety goggles or safety
shield when operating this product.
Safety Alert
Precautions
that involve your safety.
No Hands Symbol
blade
in serious
injury.
Failure will
to result
keep your
hands personal
away from
the
No Hands Symbol
blade
Failure will
to result
keep your
in serious
hands personal
away from
injury.
the
No Hands Symbol
blade
Failure will
to result
keep your
in serious
hands personal
away from
injury.
the
No Hands Symbol
blade
Failure will
to result
keep your
in serious
hands personal
away from
injury.
the
Hot Surface
To reduce
avoid
contact
the with
risk any
of injury
hot surface.
or damage,
4
_,WARN|HG;
HEAD AND UNDEHSTAND ALL INSTHUCTIONS. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious personal injury.
The term "power tool" in all of the warnings listed below refer to mains-operated
(corded)
power tools or battery-operated
(cordless) power tools.
SAVE THESE iNSTRUCTiONS
WORK AREA SAFETY
II Keep work area clean and well lit. Cluttered or dark areas invite accidents.
m Do not operate power tools in explosive atmospheres,
such as in the presence of
flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or
fumes.
m Keep children
to lose control.
ELECTRICAL
and bystanders
away while operating
a power tool.
Distractions
cause you
SAFETY
m Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
m Avoid body contact with earthed (grounded) surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed (grounded).
m Do not expose power tools to rain or wet conditions.
increase the risk of electric shock.
Water entering a power tool will
m Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged
entangled cords increase the risk of electric shock.
or
m When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
m Use battery
only with Charger/Adapter
MODEL
BATTERY
320,26302
25708
320,25705
320,29032
29005
320,67099
320,t032t
320,29036
29006
320,67099
320,t032t
PERSONAL
PACK
listed.
CHARGER/ADAPTER
SAFETY
m Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol
or medication.
A moment of inattention while operating power tools may result in serious
personal injury.
m Use safety equipment.
Always wear eye protection. Safety equipment such as dust masks,
non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will
reduce personal injuries.
m Avoid accidental starting. Ensure the switch is in the off position before plugging in.
Carrying power tools with your finger on the switch or plugging in power tools that have the
switch on invites accidents.
m Hemove any adjusting
key or wrench before turning the power tool on. A wrench or key
left attached to a rotating part of the power tool may result in personal injury.
m Do not overreach. Keep proper footing and balance
control of the power tool in unexpected situations.
at all times.
This enables better
|
1
mDress
properly.
gloves
parts.
away from
Do not wear loose clothing or jewelry. Keep your hair, clothing and
moving parts. Loose clothes, jewelry or long hair can be caught in moving
m if devices are provided for the connection
ensure these are connected
and properly
related hazards.
m Do not wear loose clothing or jewelry.
hair can be drawn into air vents.
of dust extraction
and collection
facilities,
used. Use of these devices can reduce dust-
Contain
long hair. Loose clothes, jewelry
or long
m Do not use on a ladder or unstable support.
Stable footing on a solid surface enables
better control of the power tool in unexpected situations.
POWER TOOL USE AND CARE
m Do not force the power tool. Use the correct power tool for your application.
power tool will do the job better and safer at the rate for which it was designated.
The correct
m Do not use the power tool if the switch does not turn it on or off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
m Disconnect
the plug from the power source and/or the batter pack from the power tool
before making any adjustments,
changing accessories
or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
m Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
m Maintain power tools. Check for misalignment
or binding of moving parts, breakage of
parts and any other condition
that may affect the power tool's operation,
if damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
m Keep cutting tools sharp and clean. Properly maintained
edges are less likely to bind and are easier to control.
cutting tools with sharp cutting
m Use the power tool, accessories
and tool bits etc., in accordance
with these
instructions and in the manner intended for the particular type of power tool, taking in
account the working conditions
and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
m Ensure the switch is in the off position before inserting battery pack. Inserting the
battery pack into power tools that have the switch on invites accidents.
m Recharge only with the Charger/Adapter
specified by the manufacturer.
A Charger/
Adapter that is suitable for one type of batter pack may create a risk of fire when used with
another battery pack.
m Use power tools only with specifically
designated
packs may create a risk of injury and fire.
battery
packs. Use of any other battery
m When battery pack is not in use, keep it away from other metal objects like paper clips,
coins, keys, nails screws or other small metal objects that can make a connection
from
one terminal to another. Shorting the battery terminals together may cause burns or a fire.
m Under abusive conditions,
liquid may be ejected from the battery, avoid contact.
contact accidentally
occurs, flush with water. If liquid contacts eyes, additionally
medical help. Liquid ejected from the battery may cause irritation or burns.
i
_'WARN|NG:
T° reduce the risk °f injury, user must read instructi°n
manual
If
seek
]
SERVICE
m Have your power tool serviced by a qualified
repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
m When servicing a power tool, use only identical replacement parts. Follow instructions
in the Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance instructions may create a risk of shock or injury.
m Use auxiliary handle supplied
can cause personal injury.
with the tool(Available
only in 320.26302).
Loss of control
m Hold power tools by insulated gripping surfaces when performing an operation where
the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will
also make exposed metal parts of the tool "live" and shock the operator.
m Use clamps or another practical way to secure and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves it unstable and may lead to loss of control.
m Know your power tool. Read operator's
manual carefully. Learn its applications
and
limitations,
as well as the specific potential
hazards related to this tool. Following this
rule will reduce the risk of electric shock, fire or serious injury.
m Always wear safety glasses with side shields. Everyday glasses have only impact resistant
lenses. They are NOT safety glasses. Following this rule will reduce the risk of eye injury.
m Protect your lungs. Wear a face or dust mask if the operation
will reduce the risk of serious personal injury.
m Protect your hearing. Wear hearing protection during extended
Following this rule will reduce the risk of serious person injury.
is dusty. Following this rule
periods of operation.
m Battery tools do not have to be plugged into an electrical outlet; therefore,
they are
always in operating
condition.
Be aware of possible hazards when not using your
battery tool or when changing accessories.
Following this rule will reduce the risk of electric
shock, fire or serious personal injury.
m Do not place battery tools or their batteries
explosion and possibly injury.
near fire or heat. This will reduce the risk of
m Do not crush, drop or damage battery pack. Do not use a battery pack or Charger/
Adapter that has been dropped or received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged battery immediately.
m Batteries vent hydrogen
gas and can explode in the presence of a source of ignition
such as a pilot light. To reduce the risk of serious personal injury, never use any cordless
product in the presence of open flame. An exploded battery can propel debris and chemicals.
exposed, flush with water immediately.
m Do not charge battery
risk of electric shock.
tool in a damp or wet location,
If
Following this rule will reduce the
m For best results, your battery tool should be charged in a location where the temperature
is more that 32°F (0°C) but less that 104°F (40°C). Do not store outside or in vehicles.
m Under extreme usage or temperature
conditions,
battery leakage may occur, if liquid
comes in contact with your skin, wash immediately wit soap and water, then neutralize
with lemon juice or vinegar, if liquid gets in your eyes, flush them with clean water for at
least 10 minutes, then seek immediate medical attention.
Following this rule will reduce the
risk of serious personal injury.
m Save these instructions. Refer to them frequently and use them to instruct others who may
use this tool. If you loan someone this tool, also loan them these instructions.
m if the power supply
cord is damaged,
it must be replaced only by the manufacturer
or by an
,_,WARN|NG:
READ AND UNDERSTAND ALL iNSTRUCTiONS. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious personal injury.
|
1
ill Before using battery Charger/Adapter,
read all instructions and cautionary markings in this
manual, on battery Charger/Adapter,
battery and product using battery to prevent misuse of
the products and possible injury or damage.
_kCAUTION."
To reduce the risk of electric shock or damage to the Charger/Adapter
and i
battery, charge only lithium-ion
rechargeable batteries as specifically designated on your
Charger/Adapter.
Other types of batteries may burst, causing personal injury or damage.
ill Do not use Charger/Adapter
outdoors
or expose to wet or damp conditions.
entering Charger/Adapter
will increase the risk of electric shock•
Water
ill Use of an attachment
not recommended or sold by the battery Charger/Adapter
manufacturer
may result in a risk of fire, electric shock or injury to persons. Following
this rule will reduce the risk of electric shock, fire or serious personal injury•
ill De not abuse cord or Charger/Adapter.
Never use the cord to carry the Charger/Adapter
• Do not pull the Charger/Adapter
cord rather than the plug when disconnecting from
receptacle• Damage to the cord or Charger/Adapter
could occur and create an electric shock
hazard• Replace damaged cords immediately•
ill Make sure cord is located so that it will not be stepped on, tripped over, come in
contact with sharp edges or moving parts or otherwise subjected to damage or stress.
This will reduce the risk of accidental falls, which could cause injury and damage to the cord,
which could result in electric shock•
ill Keep cord and Charger/Adapter
parts.
from
heat to prevent damage to housing
or internal
ill Do not let gasoline, oils, petroleum-based
products, etc. come in contact with plastic
parts. They contain chemicals that can damage, weaken or destroy plastic•
ill An extension
cord should not be used unless absolutely
necessary. Use of improper
extension cord could result in a risk of fire and electric shock. If an extension cord must
be used, make sure:
1. That pins on plug of extension cord are the same number, size and shape as hose of plug on
Charger/Adapter.
2. That extension
cord is properly wired and in good electrical
condition;
3. That wire size is large enough for AC ampere rating of Charger/Adapter
Cord Length (Feet)
25'
50'
100'
Cord Size (AWG)
16
16
16
NOTE: AWG = American
Wire Gauge
and
as specified below:
II Do not operate Charger/Adapter
with a damaged cord or plug, which could cause
shorting and electric shock. I1damaged, have the Charger/Adapter
repaired or replaced
authorized service technician at Sears Service Center.
by an
ill Do not operate Charger/Adapter
if it has received a sharp blow, been dropped or
otherwise
damaged in any way. Take it to an authorized service technician at Sears Service
Center for an electrical check to determine if the Charger/Adapter
is in good working order•
ill Do not disassemble
Charger/Adapter.
Take it to an authorized service technician at Sears
Service Center when service or repair is required• Incorrect reassembly may result in a risk of
electric shock or fire.
ill Unplug Charger/Adapter
from outlet
reduce the risk of electric shock.
before
attempting
any maintenance
or cleaning
to
1
[] Disconnect
ChargerlAdapter
from the power supply when not in use. This will reduce
the risk of electric shock or damage to the Charger/Adapter
if metal items should fall into the
opening. It will also help prevent damage to the Charger/Adapter
during a power surge.
[] Risk of electric
battery terminal.
shock.
Do not touch uninsulated
portion of output connector
or uninsulated
[] Save these instructions.
Refer to them frequently and use them to instruct others who may
use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse
of the product and possible injury.
iMPORTANT
SAFETY
iNSTRUCTiONS
[] SAVE THESE INSTRUCTIONS.
This manual contains important safety and operating
instructions for battery Charger/Adapter
320.25709 and battery pack 320.25708.
[] Before using battery Charger/Adapter,
read all instructions
battery Charger/Adapter,
battery and product using battery.
and cautionary
[] CAUTION. To reduce the risk of injury, charge only lithium-ion rechargeable
types of batteries may burst, causing personal injury or damage.
markings on
batteries.
Other
_L,WARN|NG:
Use of this product can generate dust containing chemicals known to
the state of California to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
[] Lead from lead-based paints.
[] Crystalline silica from bricks and cement and other masonry
[] Arsenic and chromium, from chemically treated lumber.
Your risk from these exposures
work. To reduce your exposure
products.
varies, depending upon how often you do this type of
to these chemicals:
[] Work in a well-ventilated area.
[] Work with approved safety equipment, such as those dust masks that are specially
designed to filter out microscopic particles.
Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling and
other construction activities. Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes or lay on the skin may promote absorption
of harmful chemicals.
Fig, I
Two-Speed
Gear Box
Vents
Auxillar
Handle(available
only in 320.28302)
Torque
Adjustment
Ring
Direction
of Rotation
Selector
Chuck
Jaws
(FORWARD/CENTER
Ratcheting
LOCK/REVERSE)
Keyless
Chuck
Trigger
Switch
Integrated
LED Worklight
_mD
_
_
•
•
_
_
Chuck
1/2-in. Ratcheting, single-sleeve
Motor
20 Volt DC
Switch
VSR (Variable Speed Reversible)
No Load Speed
LO 0-350 / HI 0-1,300 (RPM)
Clutch
24 Position
Torque
500 in. Ibs.
Drill/Driver Weight (without battery)
3.88 Ibs.
Battery Type
Lithium-Ion
Battery Voltage
20.0 Volt DC
Charger/Adapter
Input
120-Volts, 60 Hz AC only
Optimum Charging Temperature
32°F (0 ° C) -104°F (40°C)
10
keyless
_OD
_
*
•
•
w
°0
¸
Chuck
1/2-in. Ratcheting, single-sleeve
Motor
12.0 Volt DC
Switch
VSR (Variable Speed Reversible)
No Load Speed
LO 0-230 / HI 0-1,000 (RPM)
Clutch
24 Position
Torque
370 in. Ibs.
Drill/Driver Weight (without battery)
3.07 Ibs.
Battery Type
Lithium-Ion
Battery Voltage
12.0 Volt DC
Charger/Adapter
Input
120-Volts, 60 Hz AC only
Optimum Charging Temperature
32°F (0 ° C) -104°F (40°C)
Chuck
1/2-in. Ratcheting, single-sleeve
Motor
16.0 Volt DC
Switch
VSR (Variable Speed Reversible)
No Load Speed
LO 0-300 / HI 0-1,300 (RPM)
Clutch
24 Position
Torque
420 in. Ibs.
Drill/Driver Weight (without battery)
3.13 Ibs.
Battery Type
Lithium-Ion
Battery Voltage
16.0 Volt DC
Charger/Adapter
keyless
Input
120-Volts, 60 Hz AC only
Optimum Charging Temperature
32°F (0 ° C) -104°F (40°C)
11
keyless
KNOW
YOUR
DRILL/DRIVER
(Fig. 1)
the tool and in this operator's manual as well as a knowledge of the project you are attempting.
_,WARN|NG:Thesafeuseofthisproductrequiresanunderstandingoftheinformationon
Before use of this product, familiarize yourself with all operating features and safety rules.
ADJUSTABLE
TORQUE
The drill has a 24-position clutch. The torque adjustment
amount of torque for your application.
clutch can be turned to select the right
TWO-SPEED
GEAR BOX
The two-speed gear box is designed for drilling or driving at LO or HI speeds. A slide switch is
located on top of your drill for selecting the appropriate speed.
VARIABLE
SPEED
The variable speed trigger switch delivers higher speed with increased
speed with decreased trigger pressure.
RATCHETING
KEYLESS
trigger pressure and lower
CHUCK
The keyless chuck allows you to hand-tighten or release the drill bit in the chuck jaws. The
ratcheting feature is designed to prevent the chuck from opening during operation.
FORWARD/R EVERS E/CENTER LOCK
The drill has a direction of rotation selector located above the trigger switch for changing the
direction of bit rotation. Setting the trigger switch in the OFF (center lock) position helps reduce
the possibility of accidental starting when not in use.
AUXILIARY HANDLE (ONLY COMES WITH 320.26302)
The drill is equipped with an auxiliary handle for ease of operation
and to prevent loss of control.
LED WORKLIGHT
The LED worklight, located on the front of the drill base, illuminates
depressed. This feature provides extra light for increased visibility.
when the trigger switch is
AWARN|NG:
if any parts are broken or missing, DO NOT attempt
cord or operate drill until the broken or missing parts are replaced.
could result in possible serious injury.
to plug in the power i
Failure to do so
J
AWARN|NG:
Do not attempt to modify this drill or create accessories
not
recommended for use with this drill. Any such alteration or modification
is misuse
could result in a hazardous condition leading to possible serious injury.
_,WARN|NG:
always
To prevent accidental
remove the battery
starting that could cause serious
pack from the drill when assembling
i
and
personal injury, i
parts.
UNPACKING
This product has been shipped completely
assembled.
I!1 Carefully remove the tool and any accessories
the packing list are included.
from the box. Make sure that all items listed in
!! Inspect the tool carefully to make sure no breakage or damage occurred during shipping.
I!1 Do not discard the packing material
operated the drill.
until you have carefully inspected
and satisfactorily
I!1 If any parts are damaged or missing, please refer to the numbers listed on the back page of
operator's manual.
PACKING
LIST
Drill/Driver, Auxiliary Handle(ONLY
AVAILABLE IN 320.26302),
12
Double-ended
J
Bit, Operator's Manual
!
POWER
BAR
mThisLithium-Ion
battery
pack
isequipped
with a POWER BAR which is used to display the
battery pack's remaining run time. Press the POWER BAR button to display the LED lights. The
LED lights will stay lit for approximately 4 seconds.
NOTE: The POWER BAR can be used when the battery
is attached
or removed from tooJ t
Fig, 2
Charge
O ® O O 60-7g%
Charge
0 0 ® ® 4o-sg%
Charge
POWER
0 0 0 ® 20-3g%
Charge
BAR
O O O-E- ChargeUnder
10%
• '-,'-,',•'-
J
LOW CAPACITY
CompJeteJy
d,schorged
WARNING
ill If one LED on the POWER BAR begins to flash, the battery pack's charge is under 10%
capacity and should be recharged.
ill Unlike other battery pack types, Lithium-ion battery packs deliver fade-free power for their
entire run time. The tool will not experience a slow, gradual loss of power as you work. To
signal that the battery pack is at the end of its run time and needs to be charged, power to the
tool will drop quickly. The POWER BAR will begin to display four flashing LED lights when it is
completely discharged. When this happens, remove the tool from the workpiece and charge
the battery pack as needed.
NOTE:
POWER BAR
may also
fourTMflashing
lights due to an overload
or high The
temperature
situation
(see display
SmartChip
Battery LED
protection).
SmartChip
TM
j
BATTERY PROTECTION
SmartChip TM intuitive circuitry protects the battery pack from extreme temperature, over-discharge
and over-charge. To protect the battery from damage and prolong its life, the battery pack's
SmartChip TM circuitry will turn off the battery pack if it becomes overloaded or if the temperature
becomes too high during use. This may happen in extremely high torque, binding and stalling
situations. This intelligent system will shutdown your battery pack if its operating temperature
exceeds 176°F (80°C) and will begin normal operation when it returns to 32°F (0°C) - 122°F (50°C).
ill The POWER BAR will display four flashing LED lights if the SmartChip TM circuitry detects a
momentary overload. You can conveniently reset the battery pack by pressing the POWER
BAR button. Press the POWER BAR button again to display the remaining charge.
NOTE: if the POWER BAR continues
battery pack on the ChargerlAdapter
to flash four LED lights after reset, place the
to evaluate the battery condition
(see Fig. 4).
13
i
|
J
NOTE: A significantly
reduced run time after fully charging the battery pack indicates
that the batteries are near the end of their usable life and must be replaced.
COLD WEATHER
3
|
J
OPERATION
I!1 This Lithium-Ion battery pack will provide optimal performance in temperatures between 32°F
(0°C) and 104°F (40°C). When the battery pack is very cold, it may "pulse" for the first minute
of use to warm itself up. Put the battery pack on a tool and use the tool in a light application.
After about a minute, the battery pack will have warmed itself up and will operate normally.
WHEN TO CHARGE
THE BATTERY
PACK
The Lithium-Ion battery can be charged at any time and will not develop a "memory" when
charged after only a partial discharge. It is not necessary to run down the battery pack charge
before recharging. Remove the battery pack from the tool when convenient for you and your job.
III Use the POWER BAR to determine when you need to recharge the battery pack.
!! You can "top-off"
your battery pack's charge before starting
a big job or long period of use.
I!1 Due to Lithium-Ion's fade-free properties, the only time it is necessary to charge the LithiumIon battery pack is when the pack has reached the end of its charge. To signal the end of
charge, power to the tool will drop quickly. Charge the battery pack as needed.
HOW TO CHARGE THE BATTERY
PACK
NOTE: This Lithium-ion battery pack is shipped
first time, fully charge the battery pack.
partially
charged.
Before
using it the
A fully discharged battery pack with a temperature between 32°F (0°C) and 104°F (40°C) will
charge in about 60-120 minutes(depends
on battery's capacity).
I!1 Charge the Lithium-Ion battery pack only with
the correct Charger/Adapter.
!! Connect the Charger/Adapter to a power supply.
Fig, 3
I!1 Attach the battery pack to the Charger/
Adapter by aligning the raised ribs of the
battery pack with the slot in the Charger/
Adapter. Slide the battery pack onto the
Charger/Adapter
(Fig. 3)
I!1 The Charger/Adapter
will communicate with
the battery pack's SmartChip TM circuitry to
evaluate the condition of the battery pack.
I!1 The POWER BAR LED lights will cycle from
right to left during charging. This is part of the
normal charging operation.
I!1 After charging is complete, the green LED
on the Charger/Adapter will come on and
the POWER BAR LED lights will go off. The
POWER BAR LED lights will not be displayed
when the POWER BAR button is pressed while
the battery pack is on the Charger/Adapter.
I!1 The battery pack will fully charge, but will not
overcharge, if left on the Charger/Adapter.
NOTE: For your convenience, the Charger/
Adapter can operate with most generators
and inverters rated at 300 watts or higher.
14
i
|
J
LED FUNCTIONS
OF CHARGER/ADAPTER
(Fig. 4)
Fig, 4
LED iNDiCATOR
_)
(SEE
Hi/LO
NANUAL)
TENP.
BATTERY
RED
LED
GREEN
LED
ACTION
Hot/Cold
battery
On
Off
Charging will begin when
battery returns to
32°F (0°C)-104°F (40°C)
Off
Battery pack or Charger/
Adapter is defective
Defective
BATTERY
DEFECTIVE
CHARGING
BATTERY
PACK
[_
Charging
Off
Flashing
Charging
Fully
charged
Off
On
Charging is complete
Maintenance charging
FULL
BATTERY
CHARGING
i Flashing
A HOT BATTERY
PACK
If the battery pack is above normal temperature range, the red LED will be lit and the green
LED will be off. When the battery pack cools down to approximately 104°F (40°C), the Charger/
Adapter will automatically begin charging.
CHARGING
A COLD BATTERY
PACK
If the battery pack is below the normal temperature range, the red LED will be lit and the green
LED will be off. When the battery warms to a temperature of more than 32°F (0°C), the Charger/
Adapter will automatically begin charging.
DEFECTIVE
BATTERY
If the Charger/Adapter
be off.
detects a problem, the red LED will begin flashing and the green LED will
m If defective, remove and reinsert the battery pack in the Charger/Adapter.
reads "defective" a second time, try charging a different battery pack.
If the LED status
m If a different battery pack charges normally, dispose of the defective battery pack (see
Maintenance section).
m If a different battery pack also indicates
BATTERY
"defective,"
the Charger/Adapter
may be defective.
CHARGING
If the battery pack is within normal temperature range, the green LED will begin flashing and the
red LED will be off. The battery pack will reach a full charge. The POWER BAR LED lights will
cycle right to left during charging. This is part of the normal charging operation. The POWER
BAR LED lights will not be displayed when the POWER BAR button is pressed while the battery
pack is on the Charger/Adapter.
BATTERY
FULL
If the battery pack is within normal temperature range, the green LED will be lit and the red LED will
be off. The battery pack is fully charged and ready to use. The battery pack will fully charge, but will
not overcharge, if left on the Charger/Adapter.
The POWER BAR LED lights will not be displayed
when the POWER BAR button is pressed while the battery pack is oil the Charger/Adapter.
NOTE: Charger/Adapter
may warm up with several continuous
charge cycles. This is
part of the normal operation of the Charger/Adapter.
Charge in a well ventilated area.
15
/
J
TOATTACH
BATTERY
PACK
(Fig.5)
mLock
thetrigger
switch
onthedrillbyplacing
thedirection
ofrotation
(forward/reverse/
center
lock)selector
incenter
position
mAligntheraised
portion
onthebattery
pack
withthegrooves
onthebottom
ofthedrill,
thenattach
thebattery
pack
tothedrillas
shown
mMake
sure
thelatch
onthebattery
pack
snaps
intoplace
andthebattery
pack
issecured
tothedrillbefore
beginning
operation.
TODETACH BATTERY PACK (Fig. 5)
m Lock the trigger switch on the drill by placing the direction
lock) selector in center position
!
of rotation (forward/reverse/center
Press the latch located on the front of the battery pack to release battery pack.
m Pull forward on the battery pack to remove from the drill.
_,WARN|NG:
Battery tools are always in operating condition.
Therefore, direction
rotation selector should always be locked when not in use or carrying at your side.
16
of
]
TRIGGER
SWITCH
(Fig. 6)
To turn the drill ON, depress the switch trigger.
To turn it OFF, release the trigger.
VARIABLE
Direction
of rotation
selector
SPEED (Fig. 6)
The variable speed trigger switch delivers
higher speed with increased trigger pressure
and lower speed with decreased trigger
pressure.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER
LOCK) (Fig. 6)
The direction of bit rotation is reversible and
is controlled by a selector located above the
trigger switch.
With the drill held in normal operating position:
m Position the direction of rotation selector to
the left of the tool for drilling.
m Position the direction of rotation selector to
the right of the tool for reverse.
ill Setting the switch in the OFF (center lock)
position helps reduce the possibility of
accidental starting when not in use.
_I_CAUTION:
To prevent gear damage, always allow
stop before changing the direction of rotation.
NOTE: The drill will not run unless
the left or right.
ELECTRIC
the direction
the chuck
to come to complete
of rotation selector
is engaged
fully
|
!
i
to |
]
BRAKE
To stop the drill, release the trigger switch and allow the chuck to come to a complete stop. The
electric brake quickly stops the chuck from rotating. This feature engages automatically when you
release the trigger switch.
RATCHETING
KEYLESS
CHUCK
(Fig. 7)
Fig, 7
The drill has a ratcheting keyless chuck to
tighten or release drill bits in the chuck jaws.
The arrows on the chuck indicate which
direction to rotate the chuck body in order to
GRIP (tighten) or OPEN (release) the chuck
jaws on the drill bit. The ratcheting feature is
designed to prevent the chuck from opening
during operation.
_,WARNING:
Chuck
jaws
Do not hold the chuck
body with one hand and use the power
of the drill to tighten the chuck jaws on
the drill bit. The chuck body could slip
in your hand, or your hand could slip
and come in contact with the rotating
bit. This could cause an accident
resulting
in serious
personal
OPEN
(release)
injury.
17
Ratcheting
TWO-SPEED
GEAR
BOX
(Fig.8)
Thedrillhasatwo-speed
gearboxdesigned
fordrilling
ordriving
atLOorHIspeeds.
A
slideswitch
islocated
onthetopofthedrillto
select
either LO or HI speed. When using drill
Fig, 8
Two-speed
gearbox
switch
Hi
in the LO speed range, speed will decrease
and the drill will have more power and torque.
When using drill in the HI speed range, speed
will increase and the drill will have less power
and torque. Use LO speed for high power and
torque applications and HI speed for fast drilling
or driving applications.
NOTE: Avoid running the drill at LO
speed for extended periods of time.
Running at LO speed under constant
usage may cause the drill to become
overheated, if this occurs, cool the drill
by running it without a load at HI speed.
_CAUTION:
Never change gears while the tool is running.
could result in serious damage to the drill.
ADJUSTABLE
TORQUE
CLUTCH
Failure to obey this caution/
(Fig. 9)
When using the drill/driver for different driving applications, it is necessary to increase or
decrease the torque in order to help prevent the possibility of damaging screw heads, threads,
workpiece, etc. In general, torque intensity should correspond to the screw diameter, if the torque
is too high or the screws too small, the screws may be damaged or broken.
The torque is adjusted by rotating the torque
adjustment ring.
Fig, 9
To decrease
torque
The torque is greater when the torque
adjustment ring is set on a higher setting. The
torque is less when the torque adjustment is set
on a lower setting.
The proper setting depends on the type of
material and the size of screw you are using.
Select the option that best matches the type of
bit, fastener and material you will be using.
Torque
adjl
ring
Ill Choose the correct speed: LO or HI.
To increase
torque
ill Choose the correct torque setting.
DRILL MODE (Fig. 10)
Fig, t0
Select drill mode for drilling and other heavy
duty applications.
ill To select drill mode, rotate the torque
adjustment ring until the _.&._icon aligns with
the torque indicator and clicks into position.
18
Drillicon
Torque indicator
!
LED WORKLIGHT
(Fig. 11)
The LED worklight located on the base of the
drill will come on when the trigger switch is
depressed. The LED worklight will turn off when
the trigger switch is released. This provides
additional lighting on the surface of the
workpiece for operation in lower-light areas.
Variable
BiT STORAGE
(Fig. 12)
When not is use, the bit provided with the
drill can be stored on the base of the drill by
snapping it into place in the bit clip.
LED
worklight
Fig. t2
INSTALLING
BITS (Fig. 13)
Fig. 13
== Lock the trigger switch by placing the
direction of rotation selector in the OFF
Ratcheting
Chuck
jaws
(center) position.
keyless
chuck
OPEN
(release)
== Open or close the chuck jaws to a point
where the opening is slightly larger than the
bit size you intend to use. Also, raise the front
of the drill slightly to keep the bit from falling
out of the chuck jaws.
== Insert a drill bit.
NOTE: Rotate the chuck body in the
I
direction of the arrow marked GRIP to
close the chuck jaws. Do not use a wrench
to t ghten or oosen the chuck jaws.
J
m Tighten the chuck jaws securely on the bit.
REMOVING
BiTS (Fig. 13)
Fig= t4
WRONG!
m Lock the trigger switch by placing the
direction of rotation selector in the OFF
(center) position.
m Open the chuck jaws.
NOTE: Rotate the chuck body in the
direction of the arrow marked OPEN to
open the chuck jaws. Do not use a wrench
to t ghten or oosen the chuck jaws.
I
I
J
WRONG!
m Remove the drill bit.
A.WARN|NG:
Make sure to insert the drill bit straight into the chuck jaws. Do not
insert the drill bit into the chuck jaws at an angle then tighten, as shown in figure 15.
This could cause the drill bit to be thrown from the driJJ, resulting in possible serious
personal injury or damage to the chuck.
19
|
J
USING THE AUXiLiARY
HANDLE
ASSEMBLY
(ONLY AVAILABLE iN 320.26302 )(Fig. 15)
An auxiliary handle assembly is packed with
the drill for ease of operation and to help
prevent loss of control. The handle can be
rotated 360 ° and it can also be mounted on the
opposite side for left hand use.
m Loosen the handle assembly
handle counterclockwise.
m Rotate the handle assembly
operating position.
To tighten
by turning the
to the desired
m Securely tighten by turning the handle
assembly clockwise.
Be sure the handle assembly is securely
tightened against the clamp. This secures the
handle assembly.
DRILLING
(Fig. 16)
m Check the direction of rotation selector for
the correct setting (forward or reverse).
m Secure the material to be drilled in a vise or
with clamps to keep it from turning as the drill
bit rotates.
m Hold the drill firmly and place the bit at the
point to be drilled.
II Depress the trigger switch to start the drill.
m Move the drill bit into the workpiece, applying
only enough pressure to keep the bit cutting.
Do not force the drill or apply side pressure to
elongate a hole. Let the tool do the work.
m When drilling hard, smooth surfaces, use
a center punch to mark the desired hole
location. This will prevent the drill bit from
slipping off-center as the hole is started.
m When drilling metals, use a light oil on the
drill bit to keep it from overheating. The oil
will prolong the life of the bit and increase the
drilling action.
m If the bit jams in the workpiece or if the drill
stalls, stop the tool immediately. Remove the
bit from the workpiece and determine the
reason for jamming.
NOTE: This drill is equipped with
an electric brake. When the brake is
functioning
properly, sparks may be visible
through the vent slots in the housing. This
is normal and is the action of the brake.
,_WARNiNG:
Be prepared for binding at bit breakthrough.
When these situations
I
occur, the drill has a tendency
to grab and kick opposite to the direction of rotation and
could cause loss of control when breaking through material, if not prepared, this loss of
control can result in possible serious injury,
J
20
WOOD
DRILLING
Formaximum
performance,
usehighspeed
steelorbradpoint
bitsforwood
drilling.
mBegin
drilling
ataverylowspeed
toprevent
thebitfromslipping
offthestarting
point,
increase
speed
asthedrillbitbitesintothematerial.
mWhen
drilling
"through"
holes,
place
ablock
ofwood
behind
theworkpiece
toprevent
ragged
orsplintered
edges
ontheback
sideofthehole.
METAL DRILLING
For maximum performance,
use high speed steel bits for metal or steel drilling.
m When drilling metals, use a light oil on the drill bit to keep it from overheating.
prolong the life of the bit and increase the drilling action.
The oil will
H! Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
m Maintain a speed and pressure which allows cutting without overheating
much pressure will:
- Overheat
the bit. Applying too
the drill.
- Wear the bearings.
- Bend or burn bits.
- Produce off-center
MASONRY
or irregular-shaped
holes.
DRILLING
For maximum performance,
concrete, etc.
use carbide-tipped
masonry bits when drilling holes in brick, tile,
m Maintain a speed and pressure which allows cutting without overheating
Applying too much pressure will:
- Overheat
the bit or drill.
the drill.
- Wear the bearings.
- Bend or burn bits.
Produce off-center
!
or irregular-shaped
Apply light pressure and medium
H! Apply additional
holes.
speed for best results in brick.
pressure for hard materials such as concrete.
m When drilling holes in tile, practice on a scrap piece to determine the best speed and pressure.
Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
_WARN|NG:
Always wear safety
power too operat on or when bow
goggles or safety glasses with side shields during
ng dust. f operat on s dusty, a so wear a dust mask.
_WARN|NG:
ensure safety
and Service
reliability,Center.
all repairs should be performed
qualified
serviceTotechnician
at Sears
21
by a
GENERAL
MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from
various types of commercial solvents and may be damaged by their use. Use clean cloths to
remove dirt, dust, oil, grease, etc.
_WARN|NG:
Do not at any time let brake fluids,
gasoline, petroleum-based
products,
penetrating oils, etc., come in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which may result in serious personal injury.
1
_WARN|NG:
To avoid serious personal injury, always remove the battery pack
.m the tool and unplug the Charger/Adapter
when cleaning or performing any
BATTERIES
The battery pack is equipped with Lithium-Ion rechargeable
each charge will depend on the type of work performed.
batteries.
The duration of use from
The batteries in this tool have been designed to provide maximum trouble-free life. Like all
batteries, they will eventually wear out. Do not disassemble the battery pack or attempt to replace
the batteries. Handling of the batteries, especially when wearing rings and jewelry, could result in
a serious burn.
To obtain the longest possible
battery life, read and understand
[] It is good practice to unplug the Charger/Adapter
when not in use.
For Lithium-Ion
the operators
and remove the Lithium-Ion
battery pack
battery pack storage longer than 30 days:
[] Store the Lithium-Ion
moisture.
[] Store Lithium-Ion
battery pack where the temperature
battery packs in a 30%-50%
is below 80°F (26°C) and free of
charged condition.
[] Every six months of storage, fully charge the Lithium-Ion
battery pack.
[] Exterior may be cleaned with a cloth or soft non-metallic
brush.
BATTERY
manual.
PACK REMOVAL
AND PREPARATION
FOR RECYCLING
To preserve natural resources, please recycle or dispose of batteries properly.
This product contains lithium-ion batteries. Local, state or federal laws may
prohibit disposal of lithium-ion batteries in ordinary trash. Consult your local
waste authority for information regarding available recycling and/or disposal
options.
_WARN|NG:
Upon removal, cover the battery pack's terminals
with heavy-duty
adhesive tape. Do not attempt to destroy or disassemble the battery pack or remove
any of its components.
Lithium-ion
batteries must be recycled or disposed of properly.
Also, never touch the terminals with metal objects and/or body parts as a short circuit
may result. Keep away from children. Failure to comply with these warnings could
result in fire and/or serious injury,
22
I
CHUCK
REMOVAL
(Fig.17-19)
Thechuck
canberemoved
andreplace
bya
new
one.
mLock
thetrigger
switch
byplacing
the
direction
ofrotation
selector
incenter
position.
! Open
thechuck
jaws.
mInsert
a5/16-in.
orlarger
hexkeyintothe
chuck
ofthedrillandtighten
thechuck
jaws
securely.
mTapthehexkeysharply
withamallet
in
aclockwise
direction.
Thiswillloosen
the
screw
inthechuck
foreasyremoval.
mOpen
thechuck
jawsandremove
thehex
key.
Using
ascrewdriver,
remove
thechuck
screw
byturning
itinaclockwise
direction.
Ratcheting
keyless
chuck
Fig. t8
threads,
NOTE: The chuck screw has left handed
J
Screwdriver
m Insert the hex key into the chuck and tighten
the chuck jaws securely. Tap sharply with a
mallet in a counterclockwise
direction. This
will loosen the chuck on the spindle. It can
now be unscrewed by hand.
TO RETIGHTEN
A LOOSE CHUCK
The chuck may become loose on the spindle
and develop a wobble. Also, the chuck screw
may become loose, causing the chuck jaws to
bind and prevent them from closing.
To tighten a loose chuck or chuck screw:
m Lock the trigger switch by placing the
direction of rotation selector in center position.
m Open the chuck jaws.
m Insert the hex key into the chuck and tighten
the chuck jaws securely. Tap the hex key
sharply with a mallet in a clockwise direction.
This will tighten the chuck oil the spindle.
%
m Open the chuck jaws and remove the hex key.
m Using a screwdriver, tighten the chuck
screw by turning the chuck screw in a
counterclockwise
direction.
AWARNING: Always
wear safety
Hex key
glasses with side shields
Chuck
Jaws
during
A_WARN|NG:
To ensure safety and reliability, all repairs should
qualified service technician at Sears Service Center.
i
J
maintenance.
be performed
by a
WARN|NG:
To avoid serious personal injury, always remove the battery pack
m the tool and unplug the Charger/Adapter
when cleaning or performing any
maintenance.
23
i
J
]
@
/
@
©
20 Volt. LITHIUMqON
CORDLESS
1/2-in. DRILL / DRIVER
MODEL NUMBER 320.26302
®
20 Volt. MTHIUM-ION
CORDLESS
1/2-in. DRILL/DRIVER
MODEL NUMBER 320.26302
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence
regarding your tool.
ITEM
NO.
PARTS
NO.
PART
DESCRIPTION
QTY.
1
5820325000
Screw (L.H.)
1
2
3860084000
Chuck
1
3
3420466000
Decorate Cover
1
4
3320358000
Clutch Cap
1
5
5810032000
Tapping Screw
4
8
2790110000
Gear Case ASSY.
1
7
5620049000
Tapping Screw
2
8
5850015000
Washer
2
9
3550673000
Pinion
1
10
2730114000
DC Motor
1
11
3122817000
Speed Change Button
1
12
3700961000
Spring Stop
1
13
3700972000
Name Plate
1
14
3700971000
Name Plate
1
15
5610013000
Tapping Screw
8
18
3320359000
Right Housing ASSY.
1
17
3700963000
Lantern Ring
1
18
3122818000
F/R Button
1
Inner Lead
1 set
20
19
4870303000
Switch
1
21
4890301000
PCB ASSY.
1
22
3400260000
Contact Receptacle
23
3700960000
Handle Hoop
1
24
3320360000
Left Housing ASSY.
1
28
3700973000
Name Plate
1
28
3700405000
Bits Holder
1
27
3810357000
Bits
1
28
5640154000
Lock Bolt
1
29
3122938000
Splint
1
30
3420500000
Handle Cover
1
31
3122946000
Plate
1
25
ASSY.
1
20 Volt. LITHIUM-ION
CORDLESS
1/2-in. DRILL/DRIVER
MODEL NUMBER 320.26302
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence
regarding your tool.
iTEM
NO,
PARTS
NO,
PART
DESCRIPTION
QTY,
32
3400274000
Handle
1
33
3700974000
Name Plate
1
34
3660252000
Handle Hoop
1
SEE BACK
PAGE
FOR PARTS
ORDERING
iNSTRUCTIONS
26
mL
_rm
_jc
o_J_J
r_
rm
12 Volt.
LITHIUM=ION
CORDLESS
1/2=in. DRILL/DRIVER
MODEL NUMBER 320.29032
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence
regarding your tool.
|TEM
NO,
PARTS
NO,
1
3810357000
2
2822394000
PART
DESCRIPTION
SCREW BIT
MOTOR&GEAR
QTY,
1
ASSY
3
3700961000
4
5610098000
5
5650007000
SPRING WASHER
2
6
3860084000
CHUCK
1
TAPPING SCREW
4
7
5610106000
8
3420605000
9
5650003000
10
11
12
13
STOP SPRING
1
THREAD
FORMING
DECORATE
1
SCREW
COVER
4
1
SPRING WASHER
1
5620031000
SCREW
1
3703673000
BIT HOLDER
1
5620034000
SCREW
4
5700046000
STEEL BALL
6
14
3703909000
HEAT SINK
1
15
3700408000
GASKET
1
16
3660109000
17
4920155000
18
3320525000
1
SPRING
SHRINKABLE
1
TUBE
1
SWITCH TRIGGER
1
19
3550290000
LOCK PIN
10
20
2790118000
GEAR CASE ASSY
1
21
3704024000
MOUNTING
1
22
5610013000
TAPPING SCREW
8
23
5620325000
SCREW (L.H.)
1
24
3703983000
SPRING STOP
1
25
3123494000
SPRING HOLDER
1
26
3123133000
F/R BUTTON
1
27
3123511000
28
3320493000
29
PLATE
CLUTCH CAP
LEFT HOUSING
1
ASSY
1
3320494000
RIGHT HOUSING ASSY
1
30
3121435000
PLASTIC SLEEVE
1
31
3700972000
NAME PLATE
1
28
12 Volt. LITHIUM=ION
CORDLESS
1/2=in. DRILL/DRIVER
MODEL NUMBER 320.29032
The Model Number will be found on the Nameplate attached to the right side o1the drill. Always
mention the Model Number in all correspondence
regarding your tool.
ITEM
NO,
PARTS
NO,
32
3122817000
33
3700960000
PART
DESCRIPT|ON
SPEED CHANGE
QTY,
BUTTON
1
HANDLE HOOP
1
BRACKET
1
34
3123141000
35
3700963000
36
3402175000
37
4870346000
38
4360225000
LED
1
39
4120311000
LEAD RESISTOR
1
SEE BACK
PAGE
FOR PARTS
LANTERN
CONTACT
RECEPTACLE
TRIGGER
ORDERING
INSTRUCTIONS
29
RING
SWITCH
1
ASSY
1
1
mL
Oi_
o_
c
r-
€_
€_
16 Volt.
LITHIUM-ION
CORDLESS
1/2-in. DRILL/DRIVER
MODEL NUMBER 320.29036
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence
regarding your tool.
ITEM
NO.
PARTS
NO.
1
3810357000
2
2822394000
PART
DESCRIPTION
SCREW BIT
MOTOR&GEAR
QTY.
1
ASSY
3
3700961000
4
5810098000
5
5850007000
SPRING WASHER
2
6
3860084000
CHUCK
1
TAPPING SCREW
4
7
5810108000
8
3420605000
9
5850003000
10
11
12
13
STOP SPRING
1
THREAD
FORMING
DECORATE
1
SCREW
COVER
4
1
SPRING WASHER
1
5620031000
SCREW
1
3703673000
BIT HOLDER
1
5620034000
SCREW
4
5700046000
STEEL BALL
6
14
3703909000
HEAT SINK
1
15
3700408000
GASKET
1
16
3660109000
17
4920155000
SHRINKABLE
18
3320525000
SWITCH TRIGGER
1
1
SPRING
1
TUBE
1
19
3550290000
LOCK PIN
10
20
2790118000
GEAR CASE ASSY
1
21
3704024000
MOUNTING
1
22
5610013000
TAPPING SCREW
8
23
5620325000
SCREW (L.H.)
1
24
3703983000
SPRING STOP
1
25
3123494000
SPRING HOLDER
1
28
3123133000
F/R BUTTON
1
27
3123511000
28
3320493000
29
PLATE
CLUTCH CAP
LEFT HOUSING
1
ASSY
1
3320494000
RIGHT HOUSING ASSY
1
30
3121435000
PLASTIC SLEEVE
1
31
3700972000
NAME PLATE
1
31
16 Volt.
LITHIUM=ION
CORDLESS
1/2=in. DRILL/DRIVER
MODEL NUMBER 320.29036
The Model Number will be found on the Nameplate attached to the right side of the drill. Always
mention the Model Number in all correspondence
regarding your tool.
ITEM
NO,
PARTS
NO,
PART
DESCRIPTION
GTY,
32
3122817000
SPEED CHANGE BUTTON
1
33
3700980000
HANDLE HOOP
1
BRACKET
1
34
3123141000
35
3700963000
LANTERN
36
3402175000
CONTACT RECEPTACLE
37
4870346000
38
4360225000
LED
1
39
4120311000
LEAD RESISTOR
1
SEE BACK
PAGE
FOR PARTS
TRIGGER
ORDERING
iNSTRUCTIONS
32
RING
SWITCH
1
ASSY
1
1
33
34
35
Your Home
For repair-in
your home-of
all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
iiiiiiiiiiiiiiii
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
iiiiiiiiiiiiiiii
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
iiiiiiiiiiiiiiii
1-800-4-MY-HOME ®
Anytime, day or night
/1-_00-469-_63t
_USA
ondOonada_
www.se,
rs.co,,
www.se,
r_.c,
OurHome
HHHHHHHH
HHHHHHHH
For repair of carry-in items like vacuums, lawn equipment,
and electronic, call or go on-line for the location of your nearest
Sear,
Port,_,epair
Center.
1-800-488-1222
HHHHHHHH
Anytime, day or night (U.S.A. only)
,,,.,eo,,.co_
HHHHHHHH
To purchase a protection agreement (U.S.A.)
or maintenance agreement (Canada> on a product serviced by Sears:
1-800-827-6655
(U.S.A.) 1-800-361-6665
(Canada)
Para pedir servicio de reparaciSn
Au Canada pour service en francais:
a domicilio, y para ordenar piezas:
1-800-LE-FOYER ac
ili!il ,-888-so-HoGAR
,1- 00- 33-6937,
©Sears Brands, LLC
_ Registered Trademark / TMTrademark / SM Service Mark of Sears Brands, LLC
_ Mama Registrada / TMMarca de F_brica / sM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MDMarque d6pos6e de Sears Brands, LLC
Download PDF

advertising