Advantech | PPC-L61T | User manual | Advantech PPC-L61T User manual

User Manual
PPC-L61T
AMD LX800 Processor based
Fanless Panel PC with 6.5” TFT
LCD
Copyright
This document is copyrighted, © 2007. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
However, the original manufacturer assumes no responsibility for its use, nor for any
infringements upon the rights of third parties that may result from such use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International BusinessMachines Corporation.
AMD is a trademark of Advanced Micro Devices, Inc.
Microsoft Windows is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
All other product names or trademarks are properties of their respective owners.
For more information on this and other Advantech products, please visit our websites
at:
http://www.advantech.com
http://www.advantech.com.tw
For technical support and service, please visit our support website at:
http://service.advantech.com.tw/eservice
This manual is for the PPC-L61T series.
PPC-L61T User Manual
Part No. 2008L61T00
Edition 1
Printed in Taiwan
July 2008
ii
Declaration of Conformity
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this userís
manual, it may cause harmful interference to radio communications. Note that even
when this equipment is installed and used in accordance with this userís manual,
there is still no guarantee that interference will not occur. If this equipment is believed
to be causing harmful interference to radio or television reception, this can be determined by turning the equipment on and off. If interference is occurring, the user is
encouraged to try to correct the interference by one or more of the following measures:
„ Reorient or relocate the receiving antenna.
„ Increase the separation between the equipment and receiver.
„ Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
„ Consult the dealer or an experienced radio/TV technician for help.
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standards authority could youíre
your authority to operate the equipment.
iii
PPC-L61T User Manual
Packing List
Before you begin installing your card, please make sure that the following materials
have been shipped:
„ PPC-L61T series Panel PC
„ Accessories for PPC-L61T
„ Warranty card
„ DC plug-in housing (female) is connected on the AC/DC power adapter
„ "Drivers, Utilities and User Manual" CD-ROM
„ End User License Agreement (XPE and WinCE model)
„ Mounting kits and packet of screws
If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Additional Information and Assistance
1.
2.
Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
Warning! 1.
2.
3.
4.
5.
Input voltage rated:12-30 Vdc, 2.5 A max.
Use a 3 V@ 195 mA lithium battery.
Packing: please carry the unit with both hands and handle with
care.
Maintenance: to properly maintain and clean the surfaces, use only
approved products or clean with a dry applicator.
CompactFlash: Turn off power before inserting or removing
CompactFlash storage card.
Contact information:
Our European representative:
Advantech Europe GmbH
Kolberger Str. 7
D-40599 D¸sseldorf, Germany
Tel: 49-211-97477350
Fax: 49-211-97477300
PPC-L61T User Manual
iv
Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
Read these safety instructions carefully.
Keep this User Manual for later reference.
Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
Keep this equipment away from humidity.
Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
All cautions and warnings on the equipment should be noted.
If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
Never pour any liquid into an opening. This may cause fire or electrical shock.
Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to
the userís manual.
e. The equipment has been dropped and damaged.
DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
Caution! DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED.REPLACE ONLY WITH THE SAME OR EQUIVALENT
TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED
BATTERIES ACCORDING TO THE MANUFACTURERíS INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
v
PPC-L61T User Manual
Wichtige Sicherheishinweise
1.
2.
3.
Bitte lesen sie Sich diese Hinweise sorgfältig durch.
Heben Sie diese Anleitung für den späteren Gebrauch auf.
Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie
Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch
zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht
zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen
oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann. Es
sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom
Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung
vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in
das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen
Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen
und von einer qualifizierten Servicestelle zu überprüfen:
15. Netzkabel oder Netzstecker sind beschädigt.
16. Flüssigkeit ist in das Gerät eingedrungen.
17. Das Gerät war Feuchtigkeit ausgesetzt.
18. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder
Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.
19. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
20. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
21. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz
nur durch densellben order einem vom Hersteller empfohlene-mahnlichen Typ.
Entsorgung gebrauchter Batterien navh Angaben des Herstellers.
22. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf nicht fachmännische Weise gewechselt wird. Verfangen Sie die Batterie nur gleicher oder
entsprechender Type, wie vom Hersteller empfohlen. Entsorgen Sie Batterien
nach Anweisung des Herstellers.
23. Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt
70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend der IEC704-1 erstellt. Advantech lehnt jegliche Verantwortung für die Richtigkeit der in
diesem Zusammenhang getätigten Aussagen ab.
PPC-L61T User Manual
vi
Contents
Chapter
1
General Information ............................1
1.1
1.2
1.3
Introduction ............................................................................................... 2
General Specifications .............................................................................. 2
LCD Specifications.................................................................................... 4
Figure 1.1: LCD Specifications ..................................................... 4
Dimensions ............................................................................................... 4
Figure 1.1 PPC-L61T dimensions................................................ 4
1.4
Chapter
2
System Setup .......................................5
2.1
2.3
2.4
2.5
A Quick Tour of the Panel PC ................................................................... 6
Figure 2.1 Front View of the PPC-L61T Panl PC ........................ 6
Figure 2.2 Left Side of the PPC-L61T.......................................... 6
Figure 2.3 Rear View of the PPC-L61T ....................................... 7
Figure 2.4 Panel PC I/O............................................................... 7
Installation Procedures.............................................................................. 8
2.2.1 Connecting the Power Cord.......................................................... 8
2.2.2 Connecting the Keyboard or Mouse ............................................. 8
2.2.3 Switching On the Power................................................................ 8
Figure 2.5 Switching on the power .............................................. 8
Running the BIOS Setup Program ............................................................ 8
Installing System Software........................................................................ 9
Installing the Drivers.................................................................................. 9
3
Hardware and Peripheral Installation ..
2.2
Chapter
.............................................................11
3.1
3.2
3.3
Overview of Hardware Installation and Upgrading.................................. 12
Installing the Storage Device and Memory ............................................. 12
Installing the Optional accessory ............................................................ 12
3.3.1 Installing Extension HDD kit........................................................ 12
3.3.2 Installing the MiniPCI Wireless LAN module............................... 15
Chapter
3
.............................................................15
Chapter
4
Jumper Settings and Connectors ....17
4.1
Setting Jumpers ...................................................................................... 18
4.1.1 Jumpers and Switches on Motherboard ..................................... 18
Table 4.1: Jumpers and their functions on Motherboard ........... 18
4.1.2 Locating Jumpers on Motherboard ............................................. 19
Figure 4.1 Locating Jumpers on Motherboard........................... 19
4.1.3 Connectors on Motherboard ....................................................... 19
Table 4.2: Connectors on Motherboard..................................... 19
4.1.4 Locating Connectors on Motherboard......................................... 20
Figure 4.2 Locating Connectors on the PPC-L61T Mother-board
(front side) ................................................................ 20
Figure 4.3 Locating Connectors on the PPC-L61T Mother-board
(back side) ................................................................ 20
vii
PPC-L61T User Manual
4.2
4.3
PPC-L61T User Manual
Jumper setting on Mother-Board ............................................................ 21
4.2.1 CMOS Clear for External RTC (JP1) .......................................... 21
Table 4.3: Clear CMOS / External RTC (JP1)........................... 21
4.2.2 AT/ATX power Setting Power feature setting (J1) ...................... 21
Table 4.4: AT/ATX Power setting (J1)....................................... 21
COM port interface.................................................................................. 22
4.3.1 COM port Pin 9 power output setting (CN13) ............................. 22
Table 4.5: COM port Pin 9 power output setting (CN13)........... 22
4.3.2 COM port Pin 9 power output value setting (CN10) ................... 22
Table 4.6: COM port Pin 9 power output value setting (JP2) .... 22
viii
Chapter
1
1
General Information
This chapter gives background
information on the PPC-L61T
Panel PC.
Sections include:
„ Introduction
„ General Specifications
„ LCD Specifications
„ Dimensions
1.1 Introduction
The PPC-L61T panel PC is an AMD low-power LX800 processor computer that is
designed to serve a Human machine interface (HMI) and as a multimedia computer.
It is a PC based system with 6.5"color TFT LCD display and aluminum front cover,
the PPC-L61T is as compact and user friendly as a multi-function computer.
For system integrators, the simple, complete, compact system lets you easily build a
panel PC into your application. Common industrial applications include factory automation systems, precision machinery, and production process control. It is also suitable for many mon-industrial applications, including car part automation and
interactive kiosk system. Our Panel PC is a reliable, cost effective solution to your
application°Øs processing requirements.
1.2 General Specifications
General
„ Dimensions (W x H x D): 202 x 148 x 49 mm
„ Weight: 1.2 kg
„ Power supply:
– Input voltage: 12 ~ 30 V, 2.5 A
– Power Adapter: 19 V @ 3.19 A
„ Disk Drive Housing: Optional for exteranl SATA HDD kit
„ Front panel: IP65/NEMA 4 compliant
Standard PC functions
„ CPU: On board AMD LX800 500MHz processor
„ Chipset: Integrated in AMD CS5536AD South Bridge
„ BIOS: Award 256 KB Flash BIOS, ACPI 2.0 Compliant
„ System Chipset: AMD CS5536AD
„ System Memory: One 200-pin SODIMM socket, accepts up to 1 GB DDR333/
400 SDRAM
„ Solid state disk: Supports one 50-pin socket for Compact-Flash type I/II (True
IDE mode)
„ Serial ports: one RS-232/422/485 serial port one RS232 serial port. All ports
are compatible with 16C550. UARTs, Pin 9 with +5 V/+12 V power supply
selectable
„ Universal serial bus (USB) port: Supports up to four USB2.0 (2 internal, 2
external)
„ Mini PCI bus expansion slot: Accepts one type III mini PCI bus card
„ Watchdog timer: 256level timer intervals from 1 to 255 seconds Jumperless
selection and software enabled/disabled
„ RTC Battery: 3.0 V @ 195 mA lithium battery
„ Power management: Supports power saving modes including Normal/
Standby/Suspend modes. APM 1.2 compliant
„ Audio controller: ALC 650 AC97 Ver. 2.0 compliant interfaces, Multi stream
Direct sound and Direct Sound 3D acceleration
„ Stereo sound: 18-bit full-duplex codec
„ Audio interface: Optional One 1.5 W speaker
PCI bus Ethernet interface
„ Chipset: Realtek RTL8100CL PCI local bus Ethernet controller
PPC-L61T User Manual
2
„
Ethernet interface: Full compliance with IEEE 802.3u 100Base-T and 10 BaseT specifications. Includes software drivers and boot ROM that supports both
RPL and PXE.
100/10Base-T auto-sensing capability
Touch screen (Optional)
Analog Resistive
Resolution
Continuous
Light Transmission
80%
Controller
RS232 interface
Durability
10 million
(Touches in a life time)
Software Driver
Support Windows XP/XP Embedded, Windows CE
Optional modules
„ Memory: 128/256/512/1024 MB DDR SODIMM
„ Operating system: Microsoft® XP, XP Embedded, CE
„ Touch screen: Analog resistive
„ Installation Accessories:
– Wall Mount kit: PPC-174 WL-MT
– Panel Mount kit: Included in standard purchase of PPC-L61T
„ Extension SATA HDD Kit (without HDD): 989KL61T00E.
19 V / 60 W AC Adapter: 1757000272
„ Power cord: 1702002600 (USA type), 1702002605( Euro type), 1700000237
(JP type), 1700000596 (China type)
„ Wireless LAN kit (802.11 b.g ): 989KL12709E
Environment
„ Operating Temperature: 0~ 50°C (32 ~ 122°F)
„ Relative Humidity: 10 ~ 95% @ 40°C (non-condensing)
„ Shock: 10 G peak acceleration (11 msec duration)
„ Certifications: EMC: CE, FCC, CCC, BSMI , VCCI 6786
Safety: UL, CE; CCC, CB. BSMI
„ Vibration: 5~500 Hz 1G RMS random vibration (HDD type)
5~500 Hz 3G RMS random vibration (CF card)
3
PPC-L61T User Manual
General Information
Type
Chapter 1
„
1.3 LCD Specifications
Figure 1.1: LCD Specifications
Display type
Max. resolution
Colors
Dot size (mm)
Luminance
6.5"TFT LCD
Viewing Angle (Horizon/Vertical)
Temperature
LCD MTBF
140°/120°
Note!
640 X 480
262K
0.207 X 0.207
400 cd/m2
-10 ~ 70°C
50,000 hours
The color LCD display installed in the Panel PC is high-quality and reliable. However, it may contain a few defective pixels which do not
always illuminate. With current technology, it is impossible to completely
eliminate defective pixels. Advantech is actively working to improve this
technology.
1.4 Dimensions
186.00
Figure 1.1 PPC-L61T dimensions
PPC-L61T User Manual
7.00
42.00
133.50
148.00
202.00
1.50
4
Chapter
2
2
System Setup
This chapter details system setup
on the PPC-L61T Panel PC.
Sections include:
„ A quick Tour on Panel PC
„ Installation procedures
„ Running the BIOS Setup Program
„ Installing System Software
„ Installing the Drivers
2.1 A Quick Tour of the Panel PC
Before you start to set up the Panel PC, take a moment to become familiar with the
locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below.
When you place the Panel PC upright on the desktop, its front panel appears as
shown in Figure 2.1.
Figure 2.1 Front View of the PPC-L61T Panl PC
When you look at the left side of the Panel PC, you will see the Complat Flash socket
at left side as shown in Figure 2.2.
Figure 2.2 Left Side of the PPC-L61T
PPC-L61T User Manual
6
Chapter 2
When you turn the Panel PC around and look at its rear cover, you will find VESA
standard holes (75x75mm) and power Button. As shown in Figure 2.3.
System Setup
Product Lable
Power Button
Figure 2.3 Rear View of the PPC-L61T
The I/O section is at the bottom of the Panel PC, as shown in Figure 2.4.
Figure 2.4 Panel PC I/O
7
PPC-L61T User Manual
2.2 Installation Procedures
2.2.1 Connecting the Power Cord
The Panel PC can only be powered by a DC electrical outlet. Be sure to always handle the power cord by holding the plug ends only.Please follow the Figure 2-5 to connect the male plug of the power cord to the DC Inlet of the Panel PC.
2.2.2 Connecting the Keyboard or Mouse
Before you start the computer, please connect the necessary mouse or keyboard to
the USB ports.
2.2.3 Switching On the Power
When you look at the bottom of the computer, you will see the power switch.
Figure 2.5 Switching on the power
2.3 Running the BIOS Setup Program
Your computer is likely to have been properly set up and configured by your dealer
prior to delivery. You may still find it necessary to use the computer’s BIOS (Basic
Input-Output System) setup program to change system configuration information,
such as the current date and time or your type of hard drive. The setup program is
stored in read-only memory (ROM). It can be accessed either when you turn on or
reset the computer, by pressing the "Del" key on your keyboard immediately after
powering on the computer.
The settings you specify with the setup program are recorded in a special area of
memory called CMOS RAM. This memory is backed up by a battery so that it will not
be erased when you turn off or reset the system. Whenever you turn on the power,
the system reads the settings stored in CMOS RAM and compares them to the
equipment check conducted during the power on self-test (POST). If an error occurs,
an error message will be displayed on screen, and you will be prompted to run the
setup program.
PPC-L61T User Manual
8
Recent releases of operating systems from major vendors include setup programs
which load automatically and guide you operating system installation. The guidelines
below will help you determine the steps necessary to install your operating system on
the computer hard drive.
Note!
The BIOS of the computer supports system boot-up directly from the CDROM drive
connected via USB interface. You may insert your system installation CD-ROM into
the CD-ROM drive.
Power on your computer or reset the system by pressing the "Ctrl"+"Alt"+"Del" keys
simultaneously. The computer will automatically load the operating system from the
diskette or CD-ROM.
If you are presented with the opening screen of a setup or installation program, follow
the instructions on screen. The setup program will guide you through preparation of
your hard drive, and installation of the operating system.
If you are presented with an operating system command prompt, such as A:\>, then
you must partition and format your hard drive, and manually copy the operating system files to it. Refer to your operating system user's manual for instructions on partitioning and formatting a hard drive.
2.5 Installing the Drivers
After installing your system software, you will be able to set up the AMD chipset,
VGA, audio, LAN, and touch screen functions. All the drivers are stored in a CD-ROM
disc entitled "Drivers and Utilities" (Pls check the correct wording on the CD) which
can be found in your accessory box.
The utility directory includes multimedia programs. Some drivers and utilities in the
CD-ROM disc have their own text files which help users install the drivers and understand their functions.
These files are a very useful supplement to the information in this manual. And more
detail of driver installation please refers to Chapter 5 to 10 of this manual.
Note!
The drivers and utilities used for the PPC-L61T are subject to change
without notice. If in doubt, check Advantech’s website or contact our
application engineers for the latest information regarding drivers and
utilities.
9
PPC-L61T User Manual
System Setup
Some distributors and system integrators may have already preinstalled system software prior to shipment of your Panel PC.
Chapter 2
2.4 Installing System Software
PPC-L61T User Manual
10
Chapter
3
3
Hardware and
Peripheral Installation
This chapter details the
installation of the PPC-L61T
hardware.
Sections include:
„ Overview of Hardware
Installation and upgrading
„ Installing the Storage Device
and Memory
„ Installing the Optional
accessory
3.1 Overview of Hardware Installation and
Upgrading
The Panel PC consists of a PC-based computer that is housed in a ruggedized aluminum front panel. Any maintenance or hardware upgrades can be completed after
removing rear panel.
Warning! Do not remove the ruggedized covers until you have verified that no
power is flowing within the computer. Power must be switched off and
the power cord must be unplugged. Every time you service the Panel
PC , you should be aware of this.
3.2 Installing the Storage Device and Memory
The Standard Panel PC computer can use a Compact Flash Card (CFC) or Optional
Extension HDD kit as a storage device.
Put the CFC into the CF slot and insert the RAM into the 200-pin SODIMM socket on
the main board.
3.3 Installing the Optional accessory
Optional accessories, like Extension HDD kit or other functional modules are available for purchase to complement PPC-L61T. The following are instructions for accessory installation.
3.3.1 Installing Extension HDD kit
1.
2.
Place the HDD on the HDD mounting Bracket and tighten the screws.
Insert Shock absorber into HDD mounting Bracket.
PPC-L61T User Manual
12
5.
6.
7.
8.
Detach and Remove the Rear cover.
Remove the SATA HDD hole through (-) Screwdriver.
Attach the SATA converter board to the Rear cover with two M2*5 screws.
Connect the IDE HDD cable to the SATA converter.
13
PPC-L61T User Manual
Hardware and Peripheral Installation
Connect the SATA HDD cable to the SATA HDD.
Plate the HDD Module into HDD Cover and tighten the screws.
Chapter 3
3.
4.
9. Connect SATA cable to the SATA Converter board through the hole.
10. Fix the SATA cable with green adhesive tape.
11. Attach HDD cover on PPC-L61 back cover with Four M3*5 screws.
12. Attached VESA Bracket to the HDD.
13. Put the Rear cover on and tighten the screws.
PPC-L61T User Manual
14
1.
2.
3.
Insert the WLAN module onto the MiniPCI slot on Motherboard.
Tight the cable between the connector (main) on the WLAN module and the
screw-in antenna hole on Middle Frame.
Screw the antenna on the antenna hole on Middle Frame shown as below picture.
RAM
WLAN
(Mini PCI)
IDE
Power
Switch
3
„
15
PPC-L61T User Manual
Chapter 3
3.3.2 Installing the MiniPCI Wireless LAN module
PPC-L61T User Manual
16
Chapter
4
4
Jumper Settings and
Connectors
This chapter tells how to set up
the Panel PC hardware, including
instructions on setting jumpers
and connecting peripherals,
switches and indicators. Be sure
to read all the safety precautions
before you begin the installation
procedures.
Sections include:
„ Setting Jumpers and
Connectors
„ CPU Installation
„ Jumper setting on MotherBoard
„ COM-port Interface
4.1 Setting Jumpers
You can configure your Panel PC to match the needs of your application by setting
jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal
pins and a small metal clip (often protected by a plastic cover) that slides over the
pins to connect them. To “close” a jumper, you connect the pins with the clip. To
“open” a jumper you remove the clip. Sometimes a jumper will have three pins,
labeled 1, 2, and 3. In this case, you would connect either pins 1 and 2 or pins 2 and
3.
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes.
An arrow is used on the motherboard to indicate the first pin of each jumper.
4.1.1 Jumpers and Switches on Motherboard
The motherboard of the PPC-L61T has a number of jumpers and Connector that
allow you to configure your system to suit your applications. The table below lists the
function of each jumper and Connector.
Table 4.1: Jumpers and their functions on Motherboard
Label
Function
JP1
CMOS clear for external RTC
J1
AT/ATX power
CN10
COM1/COM2 Pin 9 power output value setting
CN13
COM1/COM2 Pin 9 Ring & power output type setting
CN12
RTC battery
PPC-L61T User Manual
18
Chapter 4
4.1.2 Locating Jumpers on Motherboard
SW1:PWR
BTN
J1:AT/ATX
SEL
CN13:COM1/2 Pin9 SEL
CN12:Battery
JP1:Clear CMOS
Figure 4.1 Locating Jumpers on Motherboard
4.1.3 Connectors on Motherboard
On-board connectors link the Panel PC to external devices such as hard disk drives.
The table below lists the function of each connector.
Table 4.2: Connectors on Motherboard
CN1
Mic IN
CN2
Internal Speaker connector
CN3
Line in
CN4
SMBus
CN5
Line out
CN6
IDE hard drive connector
CN7
Mini PCI socket
CN8
Touch screen connector
CN9
Inverter connector
CN11
COM 3 / GPIO
CN16
LAN
CN17
USB 1+USB 2
CN18
DC input
CN19
COM2 / RS232/422/485
CN20
COM1
CN21
VGA
CN22
LVDS interface
CN23
CFC
DIMM1
Dual In-line Memory Module Socket for SDRAM
19
PPC-L61T User Manual
Jumper Settings and Connectors
CN10:Pin9
PWR SEL
4.1.4 Locating Connectors on Motherboard
Figure 4.2 Locating Connectors on the PPC-L61T Mother-board (front side)
Figure 4.3 Locating Connectors on the PPC-L61T Mother-board (back side)
PPC-L61T User Manual
20
4.2.1 CMOS Clear for External RTC (JP1)
Warning! To avoid damaging the computer, always turn off the power supply
before setting "Clear CMOS". Set the jumper back to "Normal operation"
before turning on the power supply.
Normal Operation (Default)
2
1
Clear CMOS
3
2
1
3
4.2.2 AT/ATX power Setting Power feature setting (J1)
The default setting for PPC-L61T is ATX Mode, client can easy to adjust Power Mode
to AT by jumper setting. Described as below:
Table 4.4: AT/ATX Power setting (J1)
ATX Power Model (Default)
1
AT Power Mode
1
2
21
2
PPC-L61T User Manual
Jumper Settings and Connectors
Table 4.3: Clear CMOS / External RTC (JP1)
Chapter 4
4.2 Jumper setting on Mother-Board
4.3 COM port interface
The computer provides 2 serial ports: COM1, COM 2: RS-232/422/485 (selectable
via BIOS setting)
However, if you wish to disable the port or change these parameters later you can do
this in the system BIOS setup. The table overleaf shows the default settings for the
computer’s serial ports.
COM1 and COM2 are one set. You can exchange the address range and interrupt
IRQ of COM1 for the address range and interrupt IRQ of COM2. After exchanging:
COM1’s address range is 3F8 ~ 3FF and its IRQ is IRQ4.
COM2’s address range is 2F8 ~ 2FF and its IRQ is IRQ3.
4.3.1 COM port Pin 9 power output setting (CN13)
Pin 9 on COM1, COM2 port can activate external power output.
Table 4.5: COM port Pin 9 power output setting (CN13)
External power output disable (Default)
Note!
1
3
5
2
4
6
1.
2.
External power output enable
Normally, Pins 1, 3, 5 are assigned to COM1; and Pins 2, 4, 6 are
assigned to COM2.
The normal external power output value is DC 5 V.
4.3.2 COM port Pin 9 power output value setting (CN10)
Table 4.6: COM port Pin 9 power output value setting (JP2)
5 V (Default)
12 V (Optional)
1
PPC-L61T User Manual
2
3
1
22
2
3
Chapter 4
Jumper Settings and Connectors
PPC-L61T User Manual
23
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2007
Download PDF

advertising