WERTHEIM W4000 Instruction manual

Instruction Manual
7000
2
Year
WARRANTY
ONLINE
www.wertheim.net.au
EMAIL
enquiries@wertheim.net.au
enquiries@wertheim.net.au
Due to the process of continual improvement, minor
changes in product design or features may occur from
what is shown on the packaging.
2
WARNINGS & SAFETY INFORMATION
BEFORE OPERATING THIS MACHINE, PLEASE READ THESE SAFETY INSTRUCTIONS CAREFULLY
For Household Use Only
When using your Wertheim vacuum, basic safety precautions should always be observed, including
the following:
1.
Only use this machine indoors on dry surfaces
2. Turn off the vacuum controls before connecting or disconnecting from the electrical outlet
3.
Do not run over power supply cord
4.
Do not use machine if the power supply cord is damaged
5.
Do not use machine if it has been dropped, damaged, left outdoors or dropped into water
6. Do not pull or carry machine by the power supply cord, use the cord as a handle, close doors
on the cord, pull the cord around sharp corners, run the machine over the cord, or expose the
cord to heated surfaces
7.
Do not carry the machine while turned on and in use
8. Do not unplug by pulling on the power supply cord, unplug the cord by grasping the plug, not
the cord
9. Do not handle the machine or the plug with wet hands. Do not use outdoors or on wet surfaces
10. Use only the recommended attachments for this machine
11. Do not put any foreign object into machine openings, or use with blocked openings or restricted
air flow
12. Do not expose hair, loose clothing, fingers, or other body parts to openings or moving parts of
the machine
13. Do not pick up hot or burning objects
14. Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc.) or use
in the presence of explosive liquids or vapors
15. Do not pick up toxic material (chlorine, bleach, ammonia, drain cleaner, petrol etc)
16. Do not use machine in an enclosed space filled with vapors from oil based paint, paint thinner, some
moth proofing surfaces, flammable dust, or other explosive toxic vapors
17. Remove plug from electrical outlet before cleaning the machine
18. Not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of
experience or knowledge, unless they have been given supervision or instruction concerning use
of the machine by a person responsible for their safety
19. Keep out of reach of children
20. Store the machine indoors in a cool, dry area
21. Do not modify the earthed plug
22. Do not use for any purpose other than described in this instruction manual
This machine is intended for household use only and not for commercial or industrial use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
3
7000 PARTS
OPTIONAL ACCESSORIES
10
11
17
9
15
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
On/Off Buttons
Cord Retract Button
Power Adjustment Indicators
Accessories Storage Button
Accessories Storage
Dust Bag Cover Release Button
Power Cord
HEPA Filter (Not Visible)
Power Handle & Hose
Telescopic Tube
Powerhead (Height Adjustment)
Deluxe Combination Floor Tool
Small Dusting Brush
Crevice Tool
Mini Turbo Brush
Blower Attachment
Hard Floor Tool
4
4
1
4
5
6
7
16
12
13
14
1
8
3
2
ASSEMBLY STEPS
STANDARD ACCESSORIES
5
POWERING YOUR WERTHEIM 7000
Refer to page 10 for
Powering your W7000.
For max power,
make sure your
powerhead is
turned on.
RETRACTING CORD
CORRECT FLOOR SETTING
Setting for Powerhead
Setting for Floor Tool
Hard Floor
Variable Height
Adjustment
1-6
6
Carpet
ADJUST POWER SETTING
REPLACING YOUR BAG
See page 10 for settings.
CLEANING YOUR MOTOR FILTER
7
REPLACING THE HEPA FILTER
ACCESSORIES STORAGE COMPARTMENT
8
CLEARING POWERHEAD OBSTRUCTIONS - RESETTING POWERHEAD
OFF
Make sure the machine
is also disconnected
from the power source.
Be sure to completely
remove all obstructions
before pressing the
reset button.
PROBLEMS AND TROUBLESHOOTING
If a problem occurs it can usually be solved by referring to the checklist below. If your problem
can not be fixed using these tips, please contact our customer support centre (1800 815 270)
who will be happy to help.
PROBLEM
POSSIBLE CAUSE
SOLUTION
Motor does not start No power supply
or stops
Check cord, plug
and socket. If still
inoperative contact
service agent
Suction force
gradually decreases
The dust bag is full, filters are
dirty, suction hose or wand
is blocked
Empty the dust bag,
clean or replace filters,
remove objects from
hose and wand
Powerhead
not working
No power supply to powerhead Ensure that the switch
on the handle and
powerhead is switched on
Roller not rotating
on powerhead
Reset button has tripped
Make sure the roller is
clean and then press the
reset button (see above)
Powerhead is not switched on
Check the powerhead
is switched on
The belt is broken
Contact the service agent
9
ASSEMBLY STEPS - Refer to visual steps on pages 5-9 if required.
The cleaner should be switched off and disconnected from the mains supply before
commencing assembly.
• Connect the hose body connector to the cleaner
• Insert the wand into the powerhead
• Press the release button on the telescopic tube to extend or retract to desired length
• Fit the other end of the telescopic tube to the hand piece
• To detach tube from powerhead, press down on the release pedal with your foot
ACCESSORIES
Your Wertheim 7000 comes with a powerhead, a deluxe combination floor tool, a mini turbo
brush and crevice tool, a dust brush and a blower attachment.
OPTIONAL ACCESSORIES
• Hard Floor Tool
POWERING YOUR WERTHEIM 7000
If you are using your machine without the powerhead and are using any of the other tools
you only need to turn on the power for the machine (not the powerhead).
The switch on the handle is used when you have the powerhead on.
The switch on the powerhead allows you to turn off the rotating brush. (You may not want
to change the floor head, but are using on a hard floor & don’t want the brush rotating).
• Pull the power cord out from the rear of the vacuum and plug into a power socket
(Never extend the power cord further than the yellow mark)
• Press the On/Off button to switch the appliance on
• When you are finished using the appliance, unplug from the power socket and press the
power cord retract button to retract the power cord
CORRECT FLOOR SETTING
Deluxe Combination Floor Tool -
Has two floor settings. One for hard floors and the other
for carpeted surfaces. To adjust the setting, press down
on the floor tool lever.
ADJUST POWER SETTING
To adjust the suction from the machine, rotate the variable speed dial. MIN setting to reduce
the suction, and MAX setting to increase the suction.
10
EMPTYING YOUR CLEANER
Before emptying, switch ‘OFF’ and unplug the appliance
• An indicator light will illuminate when the dust bag is full
• Pull upwards on the lid release button and lift up the dust bag lid
• Slide out dust bag and replace, then close the lid
CLEANING YOUR FILTERS
• Pull upwards on the lid release button and lift up the dust bag lid
• Slide out dust bag
• Firmly pull the filter cover tab to release and remove
• Separate filter from filter cover and rinse with warm water
Ensure filter is completely dry before re-fitting
REPLACING THE HEPA FILTER
Before replacing filters, switch ‘OFF’ and unplug the appliance
• Pull upwards on the lid release button and lift up the dust bag lid
• Unclip and slide out the HEPA filter
• Replace the HEPA filter and close the dust bag lid
CLEARING POWERHEAD OBSTRUCTIONS - RESETTING POWERHEAD
If the powerhead brushbar is obstructed, it may automatically shut off. If this happens
you will need to clear any obstructing objects and reset the powerhead
• Switch ‘OFF’ and unplug the appliance
• Clear and remove all obstructions caught within the powerhead brushbar
• Press the red button on rear of powerhead to reset
• Return plug into power socket and switch both the appliance and powerhead ‘ON’
to resume cleaning
11
V3 0412