Model No. PFTL39920
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guarantee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
TREADMILL OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
10. When connecting the power cord (see page 8),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 8. To purchase a surge suppressor, see
your local PROFORM or call 1-800-806-3651
and order part number 146148.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
7. The treadmill should be used only by persons
weighing 250 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
13. Keep the power cord and the surge suppressor away from heated surfaces.
2
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BEFORE YOU BEGIN on page 4 if the treadmill
is not working properly.)
15. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails or the upper body arms while
using the treadmill.
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
19. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
20. Inspect and properly tighten all parts of the
treadmill regularly.
21. Never insert any object into any opening.
22.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
17. Never leave the treadmill unattended while it
is running. Always remove the key and unplug the power cord when the treadmill is not
in use.
18. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 5, and HOW TO FOLD
AND MOVE THE TREADMILL on page 12.)
DANGER: Always unplug the power
23. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on
your treadmill. If a decal is missing, or if it
is not legible, please call our Customer
Service Department, toll-free, to order a
free replacement decal (see ORDERING
REPLACEMENT PARTS on the back cover
of this manual). Apply the decal in the location shown. Note: The decals are not
shown at actual size.
3
BEFORE YOU BEGIN
Congratulations for selecting the new PROFORM®
CROSSWALK GTS treadmill. The CROSSWALK GTS
treadmill combines advanced technology with innovative design to help you get the most from your exercise
in the convenience and privacy of your home. And
when you’re not exercising, the unique CROSSWALK
GTS treadmill can be folded up, requiring less than half
the floor space of other treadmills.
please call our Customer Service Department toll-free
at 1-800-999-3756, Monday through Friday, 6 a.m. until
6 p.m. Mountain Time (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number of the
treadmill is PFTL39920. The serial number can be
found on a decal attached to the treadmill (see the
front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
Before reading further, please look at the drawing below
and familiarize yourself with the parts that are labeled.
Bookrack
Water Bottle Holder
(Bottle not included)
Console
Key/Clip
Handrail
Storage Latch
Upright
RIGHT SIDE
Walking Belt
Foot Rail
Circuit Breaker
Power Cord
Cushioned Walking Platform
for maximum exercise comfort
BACK
Rear Roller
Adjustment Bolts
Incline Leg
4
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included allen wrenches
and your own phillips screwdriver
,
rubber mallet
, wire cutters
, adjustable wrench
, and needlenose
pliers
.
To identify small parts during assembly, use the PART IDENTIFICATION CHART in the center of this manual.
1. Make sure that the power cord is unplugged.
1
40
119
75
40
119
With the help of a second person, carefully tip the
treadmill onto one side. Partially fold the Frame (75) so
that the treadmill is more stable. Do not fully fold the
treadmill until it is completely assembled.
Attach four Base Pads (40) to the Base (11) with four 1”
Tek Screws (119).
40
119
11
2. With the help of a second person, tip the treadmill down
to the position shown.
2
103
Attach a Wheel (37) to each side of the Base (11) with a
Wheel Bolt (36) and a Wheel Nut (38) as shown. Do not
over tighten the Bolt. The Wheel should be able to
spin freely.
Identify the Right Handrail (103) (the Handrail Wire
Harness [21] is routed through the Right Handrail). If
there are plastic ties in the lower end of the Right
Handrail, remove them. While a second person holds the
Right Handrail near the Base Wire Harness (99), connect
the Handrail Wire Harness to the Base Wire Harness. If
the connectors do not fit together easily, rotate them
and then connect them.
37
38
36
5
21
99
11
3. Insert a Plastic Shim (104) into each side of the post on
the right side of the Base (11). Next, orient the Right
Handrail (103) as shown, and insert it into the Base. Be
careful to avoid pinching the Handrail Wire Harness
(21). Note: If necessary, tap the Right Handrail with a
rubber mallet until it is fully seated in the Base. If the
Right Handrail cannot be fully seated, remove the outer
Plastic Shim and then insert the Right Handrail.
3
Attach the Right Handrail (103) to the Base (11) with
three 1” Bolts (8) and three 1/4” Star Washers (9). Do
not tighten the Bolts yet.
103
Assemble the Left Handrail (not shown) in the same
way. Note: There is not a wire in the Left Handrail.
21
9
104
8
9
11
8
4. Hold the Crossbar (1) between the Handrails (102, 103).
Attach the Crossbar with two Crossbar Screws (53). Do
not tighten the Crossbar Screws yet.
4
Attach the ring on the end of the ground wire to the small
hole in the side of the Right Handrail (103) with a Silver
Ground Screw (109).
1
109
53
102
Ground
Wire
103
53
5. Hold the Left Upper Body Arm (89) near the Left Handrail
(102) as shown. Make sure that the Resistance Knob
(98) is on the indicated side. Attach the Left Upper Body
Arm to the Left Handrail with two 3” Bolts (78), two
Washers (39), and two 3/8” Star Washers (29) as shown.
5
102
89
94
29
Attach the Right Upper Body Arm (94) to the Right
Handrail (103) as described above. Be careful not to
pinch the wires in the Right Handrail.
39
78
98
103
39
78
6
29
6. Place the Console Base (46) on the Right Handrail (103)
and the Left Handrail (not shown). Attach the Console
Base with four 1 1/4” Screws (105) (only two Screws are
shown). Do not tighten the Screws yet.
6
46
21
Insert the Wire Harness (21) through the two indicated
plastic ties on the Console Base (46). Next, insert the
Wire Harness up through the opening beside the Console
Cover (110). Make sure that the Console Cover is securely attached to the Console Base.
Refer to the inset drawing. Look at the top of the Console
Base (46). Insert the Wire Harness (21) through the plastic tie on top of the Console Base.
7. Hold the Console (10) near the Console Base (46). Touch
the Right Handrail (103) to discharge any static. Plug
the widest connector on the Wire Harness (21) into the
widest connector on the Console. If the connector does
not fit easily, rotate it and then connect it. Plug the other
connector on the Wire Harness into the other connector on
the Console. Insert the excess Wire Harness down through
the opening in the Console Base (see the inset drawing
in step 6 above). Securely tighten the plastic tie on
top of the Console Base to prevent the Wire Harness
from slipping. Then, cut off the end of the plastic tie.
110
Ties
103
105
21
Tie
46
7
21
10
46
Ties
Refer to drawing 7a. Press the Book Rack (101) onto the
Console Base (46) in the location shown.
Set the Console (10) on the Console Base (46). Insert
the excess Wire Harness (21) into the large hole in the
side of the Right Handrail (103). Securely tighten the
plastic ties on the bottom of the Console Base to
prevent the Wire Harness from slipping. Then, cut off
the ends of the plastic ties.
103
Lift the treadmill frame (see HOW TO FOLD THE
TREADMILL FOR STORAGE on page 11), but do not
latch it. Make sure that the frame is centered between
the Handrails (102, 103 [not shown]). Firmly tighten all
of the bolts and screws used in assembly steps 3, 4,
5, and 6. Then, lower the frame to the floor.
13
118
7a
101
Attach the Console (10) to the Console Base (46) with two
1/2” Silver Screws (118) and four 3/4” Screws (13). Start
all six Screws before tightening them; do not overtighten the Screws.
8. Attach the Storage Latch (14) to the left Handrail (102)
with two 3/4” Screws (13). Be careful not to overtighten the Screws.
13
46
8
102
14
13
9. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included allen wrenches in a secure place. The large allen wrench is used to adjust the
walking belt (see page 14). To protect the floor or carpet, place a mat under the treadmill.
7
TREADMILL OPERATION
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking platform. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call toll-free 1-800806-3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indicate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having
8
CONSOLE DIAGRAM
Note: If there is a thin sheet of
plastic on the console, remove it.
Clip
Key
1
CAUTION: Before operating the
Insert the key fully into the console.
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing above) and
slide the clip onto the waistband of your clothes.
Next, insert the key fully into the console. After a
moment, the displays will light. Test the clip by
carefully taking a few steps backward until the
key is pulled from the console. If the key is not
pulled from the console, adjust the position of
the clip. Then, reinsert the key into the console.
console, read the following precautions.
• Do not stand on the walking belt when turning on the power.
• Always wear the clip (see the drawing
above) while operating the treadmill.
• Adjust the speed in small increments to
avoid sudden jumps in speed.
2
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed
water bottle in the water bottle holder.
Press the Start button or the Speed ▲ button to
start the walking belt.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
STEP-BY-STEP CONSOLE OPERATION
As you exercise, change the speed of the walking
belt as desired by pressing the Speed buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph. Note: The console can display speed and
distance in either miles or kilometers (see
SPEED DISPLAY on page 10). For simplicity, all
instructions in this section refer to miles.
Before operating the console, make sure that the
power cord is properly plugged in (see page 8).
Follow the steps on this page and page 10 to operate
the console.
9
To stop the walking belt, press the Stop button.
The elapsed time will begin to flash in the Time/
Distance display.
ment. When the desired unit of measurement is
selected, remove the key and then reinsert it.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
Note: During the first few minutes that the treadmill
is used, inspect the alignment of the walking belt,
and align it if necessary (see page 14).
3
5
Change the incline of the treadmill as desired.
Step onto the foot rails, press the Stop button, and
remove the key from the console. Keep the key in a
secure place.
To change the incline of the treadmill, press the
Incline buttons until the desired incline level is
reached.
4
When you are finished exercising, remove the
key.
WARNING:
Follow your progress with the three displays.
Removing the key
does not cut off power to the incline system. To prevent movement of the treadmill
and possible injury, unplug the power cord
when the treadmill is not in use.
Time/Distance
display—This display
shows the elapsed time
and the distance that
you have walked or run.
Mode Indicator
The display will change
from one number to the
other every few seconds, as shown by the mode
indicators. When the Stop button is pressed, the
elapsed time will flash in the display.
HOW TO USE THE UPPER BODY ARMS
As you walk on the treadmill, hold either the handrails
or the upper body arms. To exercise your arms, shoulders, and back for a total body workout, move the
upper body arms forward and back as you walk on the
treadmill.
Fat Calories/Calories
display—This display
shows the approximate
numbers of fat calories
and calories you have
burned (see FAT BURNING on page 15). The display will change from
one number to the other every few seconds, as
shown by the mode indicators.
Upper
Body
Arms
Speed display—This
display shows the speed
of the walking belt.
Resistance
Knobs
Note: The console can
display speed and distance in either miles or
kilometers. The letters
MPH or KPH in the
Speed display will show
which unit of measurement is selected. To change
the unit of measurement, hold down the Stop button, insert the key into the console, and continue
to hold the Stop button for a moment. An “E” for
English miles or an “M” for metric kilometers will
appear in the Fat Calories/Calories display. Press
the Speed ▲ button to change the unit of measure-
To vary the intensity of your upper body exercise, the
resistance of the upper body arms can be adjusted. To
increase the resistance, turn the resistance knobs
clockwise; to decrease the resistance, turn the knobs
counterclockwise.
10
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) in order to
raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown at
the right. To decrease the possibility of injury, bend your
legs and keep your back straight. As you raise the treadmill, make sure to lift with your legs rather than your
back. Raise the treadmill about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left thumb, press the storage
latch to the left. Raise the treadmill until the storage latch
closes over the catch. Make sure that the storage latch is
fully engaged over the catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Engaged
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the storage
position as described above. Make sure that the storage latch
is fully engaged over the catch.
1. Hold the upper ends of the handrails. Place one foot on the
base as shown.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not move the treadmill over an uneven surface.
Base
3. Place one foot on the base, and carefully lower the treadmill
until it is resting in the storage position.
11
Front Wheels
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left thumb, press the storage latch to the
left. Pivot the treadmill down until the frame and foot rail are
past the storage latch.
Storage
Latch
2. Hold the treadmill firmly with both hands, and lower the treadmill to the floor. Do not drop the treadmill frame to the
floor. To decrease the possibility of injury, bend your
legs and keep your back straight.
12
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department tollfree at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM:
The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 8. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
c
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE POWER CORD. Remove the screws from
the hood, and carefully remove the hood.
Locate the Reed Switch (44) and the Magnet (45) on
the left side of the Pulley (50). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(33) and move the Reed Switch slightly. Retighten the
Screw. Re-attach the hood, and run the treadmill for a
few minutes to check for a correct speed reading.
13
b
44
1/8”
50
45
33
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 2 to
3 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
b
2”–3”
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our toll-free Customer Service
Department.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the allen wrench to
turn the left rear roller bolt clockwise 1/2 of a turn; if
the walking belt has shifted to the right, turn the
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Plug in the power cord,
insert the key, and run the treadmill for a few minutes.
Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the allen wrench, turn both rear roller bolts clockwise,
1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Be
careful to keep the walking belt centered. Plug in the
power cord, insert the key and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
a
b
PROBLEM: ONE OF THE UPPER BODY ARMS SQUEAKS DURING USE
SOLUTION: a. Correcting this problem requires a small amount of
white marine grease, available at most hardware
stores. Turn the Resistance Knob (98) counterclockwise until it can be removed. Remove the Resistance
Cone (93) and the Upper Body Arm (89), along with
the 3/8” Washers (57), Spring Washer (95), Thrust
Washers (96), and Thrust Bearing (97). (Note: If the
Resistance Sleeve [92] comes out of the Resistance
Bracket [91], press it back in.) Apply a thin layer of
white marine grease to the outer surface of the
Resistance Cone (93). Reattach all parts in the order
shown at the right.
14
a
91
89
92
93
96
57
97
95
57 98
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
HOW TO MEASURE YOUR HEART RATE
To measure your
heart rate, first exercise for at least four
minutes. Then, stop
exercising and place
two fingers on your
wrist as shown. Take
a six-second heartbeat count, and multiply the result by 10 to find your heart rate. For example, if your six-second heartbeat count is 14, your heart
rate is 140 beats per minute. (A six-second count is
used because your heart rate will drop rapidly when
you stop exercising.)
WORKOUT GUIDELINES
Each workout should include the following three parts:
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone. For maximum fat burning, adjust
the speed and incline of the treadmill until your heart
rate is near the middle of your training zone.
Aerobic Exercise
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
15
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• The MODEL NUMBER of the product (PFTL39920)
• The NAME of the product (PROFORM® CROSSWALK GTS treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED DRAWING in the center of this manual)
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products used for commercial or rental purposes; or products used as store display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 188703 R0902A
Printed in USA © 2002 ICON Health & Fitness, Inc.
PART IDENTIFICATION CHART
Remove this chart and use it to identify small parts during assembly. Save
this chart and the EXPLODED DRAWING/PART LIST for future reference.
Silver Ground
Screw (109)–1
Crossbar Screw
(53)–2
1/2” Silver
Screw (118)–2
1 1/4” Screw (105)–4
1” Tek Screw
(119)–4
1/4” Star Washer
(9)–6
(May be an internal
Star Washer)
3/8” Star Washer
(29)–4
Washer (39)–4
3/4” Screw (13)–6
Wheel Nut (38)–2
Wheel Bolt (36)–2
3” Bolt (78)–4
1” Bolt (8)–6
PART LIST—Model No. PFTL39920
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20*
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
1
1
2
1
1
1
1
6
6
1
1
1
9
1
2
7
1
1
1
1
1
4
1
1
19
1
1
1
9
1
2
1
1
6
4
2
2
6
9
4
2
1
1
1
1
1
2
4
2
1
1
2
2
1
1
1
6
2
1
1
2
2
3
Description
Crossbar
Key/Clip
Incline Leg Pivot Bolt
Battery Cover
Left Foot Rail
Lift Motor
Rear Roller
1” Bolt
1/4” Star Washer
Console Assembly
Base
Motor Belt
3/4” Screw
Storage Latch
Frame Pivot Spacer
8” Cable Tie
Motor Nut
Pulley/Flywheel/Fan
Motor
Motor/Pulley/Flywheel/Fan
Handrail Wire Harness
Belt Guide Screw
Motor Hood
Hood Shield
Screw
Controller
Motor Swivel Bolt
Motor Tension Nut
3/8” Star Washer
Motor Tension Washer
Motor Tension Bolt
Incline Stop Bracket
Clip Screw
Cage Nut
Endcap Screw
Wheel Bolt
Wheel
Wheel Nut/Lift Nut
Washer
Base Pad
Base Endcap
Latch Catch
Reed Switch Clip
Reed Switch
Magnet
Console Base
Front Isolator
Platform Screw
Isolator
Front Roller/Pulley
Front Roller Adj. Bolt
Incline Wheel
Console Screw
Power Cord
Power Cord Grommet
Circuit Breaker
3/8” Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Rear Platform Screw
Releasable Tie
Key No. Qty.
R0902A
Description
64
1
Choke
65
2
Belt Guide
66
6
Plastic Fastener
67
1
Walking Belt
68
1
Walking Platform
69
1
Belly Pan
70
8
Electronics Screw
71
1
Incline Wire Harness
72
1
Upright Grommet
73
2
Isolator Screw
74
1
Allen Wrench
75
1
Frame
76
2
Front Endcap
77
2
Incline Wheel Bolt
78
4
3” Bolt
79
4
Incline Wheel Nut
80
1
Ground Wire
81
2
Hood Screw (Front)
82
1
Incline Leg
83
2
Rear Roller Adj. Bolt
84
1
Left Endcap
85
1
Right Endcap
86
1
Incline Motor Bolt
87
2
Belly Pan Screw
88
2
Foam Grip
89
1
Left Upper Body Arm w/Foam Grip
90
2
Resistance Bolt
91
2
Resistance Bracket
92
2
Resistance Sleeve
93
2
Resistance Cone
94
1
Right Upper Body Arm w/Foam Grip
95
2
Spring Washer
96
4
Thrust Washer
97
2
Thrust Bearing
98
2
Resistance Knob
99
1
Base Wire Harness
100
1
Motor Belt Shield
101
1
Book Rack
102
1
Left Handrail
103
1
Right Handrail
104
4
Shim
105
4
1 1/4” Screw
106
4
Plastic Stand-off
107
1
Power Board
108
1
Power Board Plate
109
1
Silver Ground Screw
110
1
Console Cover
111
1
Warning Decal
112
1
Incline Warning Decal
113
2
Handrail Endcap
114
1
Right Foot Rail
115
1
Hole Cap
116
1
Motor Controller Wire
117
1
5/32” Allen Wrench
118
2
1/2” Silver Screw
119
4
1” Tek Screw
#
1
8” White Wire, 2F
#
1
4” White Wire, M/F
#
1
4” Blue Wire, M/F
#
1
4” Red Wire, M/F
#
1
User’s Manual
* Includes all parts shown in the box
# These parts are not illustrated
83
39
84
31
29
17
32
88
86
6
91
90
89
83
117
39
74
17
93
92
5
77
7
48
97
57
85
75
4
13
95
52
3
42
25
57
96
118
46
98
66
79
80
73
49
13
61
13
112
111
101
79
82
59
22
65
66
48
110
35
10
52
3
71
77
87
114
61
73
66
69
15 38
48
29 45
76
16
67
50
63
44
68
116
2
66
49
22
43
33
39
33
40
119
33
35
76
65
39
48 78
33
60
51
39
14
36
38
29
113
102
1
37
15
78
21
39
33
34
104
39
34
41
104
113
38
103
13
53
33
119
70
40
8
34
9
53
9
100
8
57
27
12
113
58
109
105 21
119
40
33
28
41
38
64
31 30
29
105
17
72
37
70 8
36
11
9
119
40
108
25
106
107
99
8
19
81 9
18
20*
25
54
56 115
57
29
70
57
95
96
97
25
29
57
58
26
70
55
98
24
23
81
92
91
93
94
88
90
25
EXPLODED DRAWING—Model No. PFTL39920
R0902A