Martin Professional MAC 2000 Profile II User manual

MAC 2000 Profile II
user manual
133½°
133½°
271
759
10°
28°
743
613
488
171
min c/c
408
270°
545
270°
490
530
© 2000-2002 Martin Professional A/S, Denmark. All rights reserved. No part of this manual may be reproduced, in any form or by any
means, without permission in writing from Martin Professional A/S, Denmark. Printed in Denmark.
P/N 35000090 Rev. K
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
TRANSPORTATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Included items. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transport locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Single flight case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Double flight case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
5
6
LAMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
About the HMI 1200 W/S lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Lamp replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
AC POWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power supply adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Reduced power function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
RIGGING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Clamping the fixture to a truss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Navigation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DMX address and protocol setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tailoring performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Readouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
13
13
14
15
15
OPTICAL CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Gobos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rotating gobo wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color/gobo wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Effect wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
17
18
19
EFFECTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Dimming and strobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Color temperature correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Random color mixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fixed colors and gobos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gobos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Effect wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Focus and zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pan and tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
20
20
20
20
20
21
21
21
21
21
ROUTINE MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Software installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
DMX PROTOCOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CONTROL MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
ADJUSTMENT SUBMENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
DISPLAY MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
CIRCUIT BOARD CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
SPECIFICATIONS
MAC 2000 PROFILE II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
INTRODUCTION
Thank you for selecting the MAC 2000 Profile II. This extraordinary 1200 watt luminaire from Martin Professional
provides CMY color mixing, continuous 0 - 178 mireds color correction, a color/gobo wheel with 4 dichroic color
filters and 3 fixed glass gobos, 10 indexed-rotation gobos on 2 wheels, a 2-position rotating-effect wheel with 3-facet
prism, beam shaper, and variable frost; combined full-range dimmer and shutter, iris, zoom, focus, 540° of pan, and
267° of tilt. It is available with a magnetic or electronic ballast.
For the latest firmware updates, documentation, and other information about this and all Martin Professional products,
please visit the Martin web site at http://www.martin.dk.
Safety information
Warning!
This product is for professional use only. It is not for household use.
This product presents risks of lethal or severe injury due to fire and heat, electric shock, ultraviolet radiation, lamp
explosion, and falls. Read this manual before powering or installing the fixture, follow the safety precautions listed
below and observe all warnings in this manual and printed on the fixture. If you have questions about how to operate
the fixture safely, please contact your Martin dealer or call the Martin 24-hour service hot line at +45 70 200 201.
Protecting against electric shock
• Disconnect the fixture from AC power before removing or installing the lamp, fuses, or any part, and when not in use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical codes and has both overload and
ground-fault protection.
• Do not expose the fixture to rain or moisture.
• Refer any service operation not described in this manual to a qualified technician.
Protecting against UV radiation and lamp explosion
• Never operate the fixture with missing or damaged lenses and/or covers.
• When replacing the lamp, allow the fixture to cool for at least 15 minutes before opening the fixture or removing the
lamp. Protect your hands and eyes with gloves and safety glasses.
• Do not stare directly into the light. Never look at an exposed lamp while it is lit.
• Replace the lamp if it becomes defective or worn out, or before usage exceeds the maximum service life.
Protecting against burns and fire
• Never attempt to bypass the thermostatic switch or fuses. Always replace defective fuses with ones of the specified
type and rating.
• Keep all combustible materials (for example fabric, wood, paper) at least 1 meter (39 inches) away from the fixture.
Keep flammable materials well away from the fixture.
• Do not illuminate surfaces within 3 meter (10 inches) of the fixture.
• Provide a minimum clearance of 0.1 meters (4 inches) around fans and air vents.
• Never place filters or other materials over the lens.
• The exterior of the fixture can get very hot. Allow the fixture to cool for at least 5 minutes before handling.
• Do not modify the fixture or install other than genuine Martin parts.
• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
Protecting against injury due to falls
• Do not lift or carry the fixture alone.
• When suspending the fixture, verify that the structure can hold at least 10 times the weight of all installed devices.
• Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary
attachment such as a safety cable.
• Block access below the work area whenever installing or removing the fixture.
4
MAC 2000 Profile II
TRANSPORTATION
Important! Release the transport locks before operating the fixture.
Included items
The MAC 2000 Profile II is shipped in a 1 or 2 unit flight case
that contains the following items.
•
•
•
•
•
User manual
2 clamp attachment brackets
2 x 20 A main fuses (for use with 100-130 V local power supply)
2 x 15 A main fuses (for use with 200-250 V local power supply)
XLR cable
Transport locks
The head and yoke may be locked for transportation and service.
The locks are shown in Figure 1. The fixture must be unlocked
before operation.
Figure 1: Pan and tilt locks
Single flight case
Unpacking the fixture
1
Remove the top of the flight case.
2
With one person on each side, lift the fixture out of the bottom
of the flight case.
3
Release the pan and tilt locks before operating.
Packing the fixture
1
Disconnect the fixture from power and allow it to cool.
2
Lock the head and yoke in the position shown in Figure 2.
3
Place the fixture in the bottom of the flight case. Place the
top section over the fixture without forcing.
Figure 2: Single unit transport position
Transportation
5
Double flight case
Unpacking
2
Release the head (tilt) transport lock.
3
Install rigging hardware as described on page 12.
4
With one person on each side, lift the fixture out of the flight
case.
R
Open the flight case and pull the drawer all the way out.
F
1
O
N
T
Packing
1
Disconnect the fixture from power and allow it to cool.
2
Turn the yoke parallel to the sides of the base with the tilt
lock closest to the back.
3
Pull the transport drawer all the way out. With one person
on each side, place the fixture on the drawer with the arrow
pointing in.
4
Remove and stow rigging hardware. Coil and stow the
power cord in the door.
5
Tilt the head so that the lens points away from the door as
shown in Figure 3. Lock the head in the horizontal position.
Do not lock the yoke.
6
Figure 3: Double unit transport position
Slide the drawer all the way in without forcing. Close the flight case.
Setup for flight case testing
The double flight case has two slide-out arms from which the fixture can hang for testing and setting. Though
unnecessary, the pan and tilt reset can be cancelled by pressing [Menu] and [Enter] at the same time.
6
1
Open the flight case and pull the drawer all the way out. Release the transport locks.
2
Pull the test arms all out. Tilt the fixture up and over the slide arms so that the handle cross-braces that are
second from the back rest on the arms. The fixture should rest at an angle.
3
Push the transport drawer into the flight case.
MAC 2000 Profile II
LAMP
About the HMI 1200 W/S lamp
TOP
The MAC 2000 Profile II comes with a double-ended OSRAM
HMI 1200 W/S discharge lamp installed. This highly-efficient
short-arc source provides an exceptionally stable 6000K color
temperature, a color rendering index greater than 90, and an
average life of 750 hours.
TOP
The lamp is capable of hot restrike. This feature, however, is only
supported by the MAC 2000 Profile II with electronic ballast.
The ends of the lamp have specially-developed keys, shown in
Figure 6, to ensure proper installation. Do not use HMI 1200 W/S
lamps with the non-keyed SFc 10-4 base.
Warning!
Installing any other lamp may create a safety
hazard or damage the fixture!
The lamp has an average life of 750 hours. To reduce the risk of
explosion, replace the lamp before usage exceeds 125% of the
average life, i.e., before it exceeds 940 hours. To read lamp hours
from the control panel, please refer to Readouts on page 14.
For optimum performance, avoid turning off the lamp before it
has warmed up fully.
Figure 4: Lamp access
Lamp replacement
Important! Do not touch the quartz bulb with bare fingers.
Replacement lamps are available from your Martin dealer. Please
order Martin P/N 97010304.
The clear quartz bulb must be clean and free of any oils from
your fingers. Clean the lamp with an alcohol wipe and polish it
with a dry cloth, particularly if you accidentally touch the bulb.
Replacing the lamp
1
Disconnect the fixture from power and allow it to cool. Lock
the head horizontally with the top up.
2
See Figure 4. Release the 4 quarter-turn fasteners marked
with arrows on the rear plate. Pull the lamp assembly
straight back as far as it goes and let it rest in place.
3
See Figure 5. Pull the retention spring on the left end up
and then swing the end of the lamp out. Pull the other end
out of the socket.
Figure 5: Lamp removal
Lamp
7
4
See Figure 6. With the nipple on the bulb facing the back,
insert the right end of the new lamp in the socket. Pull up
on the left spring and snap the other end into place.
5
Lift the lamp assembly so that lamp is level with the center
of the reflector. Push the assembly straight in until it seats,
making sure the lamp passes through the reflector opening.
Lock the 4 quarter-turn fasteners.
6
When installing a new lamp, reset the lamp hour and lamp
strike counters as described on page 14.
Aligning the lamp
1
Switch on the MAC 2000 Profile II and allow it to reset.
Using either a controller or the control module, turn on the
lamp and project an open white beam on a flat surface.
2
Center the hot spot vertically using the top Allen-head
adjustment screw in the center of the rear plate.
3
If there is significant hot spot, turn the bottom adjustment
screw counterclockwise until the light is evenly distributed.
If the light is brighter around the edge than it is in the
center, or if light output is low, turn the bottom adjustment
screw clockwise until the light is bright and evenly
distributed.
4
Figure 6: Lamp insertion
Repeat step 2.
Figure 7: Lamp adjustment
8
MAC 2000 Profile II
AC
POWER
WARNING! For protection from electric shock, the fixture must be grounded (earthed). The AC mains
supply shall be fitted with a fuse or circuit breaker and ground-fault protection.
Important! Verify the power supply settings before applying power.
The chapter describes:
•
•
•
•
Installing fuses
Power supply adjustments for the various MAC 2000 Profile II models
Connection to a power supply (see page 10)
The reduced power function (see page 10)
Fuses
The MAC 2000 Profile II comes with two:
• 20 AT (time delay) main fuses for use with AC supplies of 100 - 120 volts.
• 15 A main fuses for use with AC supplies of 200 - 250 volts.
Install the appropriate fuses in the holders near the power switch.
Power supply adjustments
The MAC 2000 Profile II (identified as such by the label on the base of the product) comes with an electronic or
magnetic ballast and an auto-sensing, auto-ranging switch-mode power supply. Manual adjustments are not necessary
unless you have the magnetic ballast version.
Magnetic ballast configuration
In magnetic ballast models the ballast must be tapped correctly
for the local AC voltage and frequency. The wrong setting can
cause overheating, damage, and poor performance. The factory
settings are printed on the serial number label.
CHANGING
THE MAGNETIC BALLAST SETTINGS
1
Disconnect the fixture from AC power. Remove the rear
base cover as shown in Figure 8.
2
To expose the ballast connection block, remove the screws
from each end of the side plate and tilt it down (Figure 8).
3
Find the ballast setting in Table 1.
AC frequency
50 Hz
AC voltage
Setting
200 - 218 V
208 V / 50 Hz
219 - 238 V
230 V / 50 Hz
239 - 250 V
245 V / 50Hz
200 - 218 V
208 V / 60 Hz
219 - 241 V
230 V / 60 Hz
ballast
60 Hz
Table 1: Magnetic ballast settings
Figure 8: Power supply access
AC power
9
4
Move the brown wire on the ballast connection block to
the position shown Figure 9.
5
Close the base before applying power.
Black
Brown
208 V / 60 Hz
230 V / 60 Hz
208 V / 50 Hz
230 V / 50 Hz
245 V / 50 Hz
Figure 9: Magnetic ballast connections
Power connection
Important! Connect the MAC 2000 Profile II directly to AC power. Do not connect it to a dimmer
system; doing so may damage the fixture.
You may need to install a cord cap that fits your supply on the power cable. A 3-prong grounding-type plug must be
installed following the manufacturer’s instructions. The table shows some possible pin identification schemes; if the
pins are not clearly identified, or if you have any doubts about proper installation, consult a qualified electrician.
To apply power, set the power switch on the base to the “I” position.
Wire Color
Pin
Symbol
Screw (US)
brown
live
L
yellow or brass
blue
neutral
N
silver
yellow/green
ground
green
Table 2: Cord cap connections
Reduced power function
The MAC 2000 Profile II has an automatic power reduction function, which reduces the consumption to 700W if the
shutter/dimmer is closed for more than 10 seconds. This not only increases the lamp life, but also further decreases the
overall noise emission of the fixture.
10
MAC 2000 Profile II
DATA
Important! Never connect more than 1 data input and 1 data output.
The MAC 2000 Profile II has both 3-pin and 5-pin XLR sockets for DMX input and output. The pin-out on all sockets
is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.
The sockets are wired in parallel: both inputs connect to both outputs. For reliable data transmission and to avoid
damage to the fixture, however, use one input and one output!
Connecting fixtures
• Use shielded twisted-pair cable designed for RS-485 devices: standard microphone cable cannot transmit
control data reliably over long runs. 24 AWG cable is suitable for runs up to 300 meters (1000 ft). Heavier
gauge cable and/or an amplifier is recommended for longer runs.
• Never use both outputs to split the link. To split the serial link into branches use a splitter such as the Martin
4-Channel Opto-Isolated RS-485 Splitter/Amplifier.
• Do not overload the link. Up to 32 devices may be connected on a serial link.
• Terminate the link by installing a termination plug in the output socket of the last fixture. The termination
plug, which is a male XLR plug with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3, “soaks
up” the control signal so it does not reflect and cause interference. If a splitter is used, terminate each
branch of the link.
• Martin fixtures introduced before 1997 have reversed polarity data sockets (pin 2 hot and pin 3 cold). The
socket polarity is labelled. Use a phase-reversing cable between the MAC 2000 Profile II and any Martin
device with reversed polarity.
CONNECTING
THE DATA LINK
1
Connect the DMX data input from the controller to the MAC 2000 Profile II’s 3-pin or 5-pin input (male)
socket.
2
Using the sockets that match your data cable, connect the output of the fixture closest to the controller to the
input of the next fixture.
3
Insert a male 120 Ω XLR termination plug in the 3-pin or 5-pin output of the last fixture on the link.
Data
11
RIGGING
6
25
256
25
6
256
The MAC 2000 Profile II can be placed on stage or clamped to a truss in any orientation. The Fast-Lock system
enables quick and easy fastening of the clamp brackets in 4 positions as shown Figure 10.
Figure 10: Clamp bracket positions
Warning!
Always use 2 clamps to rig the fixture. Lock each clamp with both 1/4-turn fasteners. The
fasteners are locked only when turned fully clockwise. Attach an approved safety cable to
the attachment hole in the base. Never use the carrying handles for secondary attachment.
Clamping the fixture to a truss
1 Verify that the rigging clamps (not included) are undamaged and can bear at least 10 times the weight of the
fixture. Verify that the structure can bear at least 10 times the weight of all installed fixtures, clamps, cables,
auxiliary equipment, etc.
2 Bolt each clamp securely to a clamp bracket with an M12 bolt (grade 8.8 or better) and lock nut.
3 Align a clamp with 2 mounting points in the base. Insert the fasteners into the base and turn both levers a
full 1/4-turn clockwise to lock. Install the second clamp.
4 If the truss can be lowered, fixtures can be clamped on directly from the double flight case. If the fixture must
be lifted, block access under the work area. Working safely from a stable platform, hang the fixture on the
truss with the arrow towards the area to be illuminated. Tighten the rigging clamps.
5 Install a safety wire that can bear at least 10 times the weight of the fixture. The attachment point is
designed to fit a caribiner clamp.
6 Verify that the pan and tilt locks are released. Verify that there are no combustible materials or surfaces to
be illuminated within 1 meter of the fixture, and that there are no flammable materials nearby.
FRONT
Figure 11: Rigging hardware installation
12
MAC 2000 Profile II
CONTROL
PANEL
The LED control panel is used to set the address and personalities, read lamp hours and other information, calibrate
effects, and run a test routine. Most of these functions may be performed remotely via the serial link with the Martin
MP-2 Uploader.
Navigation
The DMX address and any messages (see page 34) are displayed when the MAC 2000 Profile II is turned on. To enter
the menu, press [Menu]. Press [Up] and [Down] to move within the menu. To select a function or submenu, press
[Enter]. To escape a function or menu, press [Menu].
Note: [Enter] must be pressed and held for a few seconds to enter the utilities menu.
See Table 4 on page 28 for a complete list of the menu items.
DMX address and protocol setting
The DMX address, also known as the start channel, is the first channel used to receive instructions from the controller.
For independent control, each fixture must be assigned its own control channels. Two MAC 2000 Profile IIs may share
the same address, however, if identical behavior is desired. Address sharing can be useful for diagnostic purposes and
symmetric control, particularly when combined with the inverse pan and tilt options.
Two DMX protocols, 8-bit and 16-bit, are available. The 8-bit mode uses 20 control channels and provides full basic
control. The 16-bit mode uses 4 additional channels to provide finer gobo and pan/tilt positioning.
Setting the DMX address and protocol
1
Press [Menu] to enter the main menu.
2
Press [Up] until A dd R is displayed. Press [Enter]. To snap to channel 1, press [Enter] and [Up]. Scroll to
the desired channel and press [Enter].
3
Select PS ET from the main menu and press [Enter]. Select 8b i t or 16 bt and press [Enter].
Tailoring performance
Movement
The MAC 2000 Profile II provides options for optimizing movement for different applications.
• The protocol setting (PS ET ) setting selects 8-bit or finer 16-bit control of pan, tilt, and gobo index.
• The pan and tilt invert (P AT I ) menu swaps and/or inverts pan and tilt.
• The pan/tilt speed (P T SP ) menu provides 3 settings: FA S T , N OR M , and S LO W. NO R M is best for most
applications. F AS T provides better performance in applications where speed is most important. S LO W provides the
smoothest movement and is best in long-throw applications with slow movements through narrow angles.
• The studio mode (ST U d ) setting optimizes all effects besides pan and tilt for speed or quietness.
• The shortcuts (S CU T ) setting determines whether the color, gobo, and effect wheels always take the shortest path
between two static positions or oscillate between outer positions.
Tracking Response
The MAC 2000 Profile II has a filter algorithm that looks at several position updates in tracking control mode and
calculates the ideal response for smooth movement. Tracking response is adjustable to compensate for variations in
controller performance. In most cases the default settings work well.
Control panel
13
If tracking mode movement is not satisfactory there are 2 parameters that can be adjusted. The first is selected under
P E R S / T R A C / M O d E . The default, M O d 1 , is the best choice with controllers that calculate intermediate
positions at a steady rate. Begin by selecting the alternative, MO d 2 , which is better if the intermediate positions stray
significantly from the line of travel.
The second parameter is the number of position updates used to calculate speed. The level is adjustable between 1 and
10 under P E R S / T R A C / C A L . Increasing the number of samples increases the distance over which speed is
calculated, making movement smoother but less responsive to sudden changes. Experiment for best results.
Display
The display intensity (d I N T ) setting controls display brightness. The display on/off setting (d I S P ) determines
whether the display remains on or extinguishes two minutes after the last key-press. To flip the display, press [Up] and
[Down] simultaneously.
Lamp
There are two settings that modify lamp control: Automatic Lamp On (AL ON ) and DMX Lamp Off (DL oF ).
When A L ON is off, the lamp remains off until a “lamp on” command is received from the controller. When A LO N is
on, the lamp strikes automatically after the fixture is powered on. When A L O N is set to D M X , the lamp strikes
automatically when the fixture receives DMX data, and it extinguishes 15 minutes after DMX data is lost.
When A L O N is set to either O N or D M X , the automatic lamp strike timing is staggered to prevent all lamps from
striking at once. The delay is determined by the fixture address.
If striking lamps from the controller, note that striking many lamps at once may cause a voltage drop large enough to
prevent lamps from striking or trip the main circuit breaker. Avoid this by programming a “lamp on” sequence that
strikes lamps one at a time at 5 second intervals.
Power to the lamp can be turned off from the controller if DMX Lamp Off (d L O F ) is on. If d L O F is off, a DMX
lamp off command is executed only if position 7 is selected on the color wheel and gobo 5 is selected on both gobo
wheels. Be careful: with the magnetic ballast model, it is not possible to restrike the lamp until it has cooled for a few
minutes. (The electronic ballast model provides hot restrike.)
DMX reset
The fixture can be reset from the controller if DMX reset (P E R S / d R E S ) is ON. If DMX reset is OFF, the reset
command can only be executed if position 7 is selected on the color wheel and gobo 5 is selected on both gobo wheels.
Custom settings
The custom configuration function allows you to save and recall three sets of fixture settings. The savable settings are
DMX mode, pan/tilt speed, pan/tilt inverse and swap, DMX lamp off and reset, display settings, shortcuts, studio
mode, automatic lamp on, effects feedback, tracking algorithm, and tracking samples.
Readouts
Note: The MP-2 Uploader provides commands to display the time, temperature, and version readouts on the fixture
control panel.
Time
IN FO / TI M E provides readouts of fixture hours (H RS ), lamp hours (L HR ), and lamp strikes (L ST ). Under
each item is a resettable (R S E T ) increment counter and a non-resettable counter for total accumulated hours/strikes
since fabrication (T O TL ). To reset an increment counter, display it and then press [Up] until it reads 0. (This may also
be done remotely using the MP-2 Uploader.)
Temperature
IN FO / TE M P provides readouts of the head and base temperature in Celsius and Fahrenheit.
14
MAC 2000 Profile II
Firmware version
IN FO / VE R displays the version number of the installed firmware. The firmware version is also displayed briefly at
startup.
DMX
The D MX L menu shows the DMX start code (S T CO ) and DMX values received for each effect.
Service messages
The Service LED on the control panel lights under conditions that require fixture service, and there is a message
describing the service required. To display the message, select S M S G in the main menu. This item is available only
when the LED is lit. There are two service messages.
Re p l ac e l a mp is displayed when the lamp counter exceeds 750 hours, which is the rated average life for the
HMI 1200 W/S lamp. The maximum service life is 125% of the average life, or 940 hours.
Fi xt u re o v er h ea ti n g is displayed when the head temperature exceeds 120° C (248° F). Overheating is
likely due to dirty air filters, fans, or air vents; incorrect power supply settings, or a defective fan.
Service utilities
Important! Enter must be held for several seconds to access the utilities menu.
Test sequences
T S E Q provides a general test of all effects that can be run without a controller. U T I L / P C B t provides routines
for circuit board testing that are for service use only.
Feedback toggles
An on-the-fly position correction system monitors the color wheel, gobo wheels, gobos, rotating effects, and effect
wheel. If a position error is detected, the shutter closes while the effect resets. This feature can be disabled by turning
effects feedback (U T IL / EF Fb ) off.
The automatic pan/tilt position correction system may be temporarily turned off under U T I L / F E b A . The off
setting, however, is not saved and the system will be re-enabled the next time the fixture starts. If the system cannot
correct the pan/tilt position within 10 seconds, feedback is automatically disabled.
Adjustment
The adjustment menu (U TI L /A dj ) provides manual control for making mechanical adjustments. See page 33.
Calibration
The calibration menu ( U T I L / C A L ) provides utilities to define offsets in software that are relative to the
mechanical reset or home positions. This allows you to fine tune optical alignment and achieve uniform performance
between fixtures. Dimmer and zoom are calibrated to defined points. The other effects are calibrated relative to an
arbitrary reference fixture.
Default offset settings may be restored by selecting default offsets (UT I L/ d FO F ).
CALIBRATING
EFFECTS
1
Apply power but do not strike the lamp until zoom has been calibrated.
2
To calibrate zoom, first remove the bottom head cover. Select UT I L/ C AL /Z O OF and press [Enter].
Adjust the offset until the face of the zoom lens plate is flush with the back edge of the focus plate (Figure
12). Press [Enter] to save the setting. Replace the bottom head cover.
Control panel
15
Figure 12: Zoom calibration point
3
Pan calibration is most useful when multiple fixtures are stacked vertically. To calibrate, set zoom, focus, iris,
and tilt position for easy one-over-the-other comparison and set each fixture to the same pan DMX value.
Select one fixture to be the reference fixture. On the other fixtures, select U TI L /C A L/ P OF and press
[Enter]. Adjust the offset as necessary to align the beam with the reference beam. Press [Enter] to save the
setting.
4
Tilt calibration is most useful when multiple fixtures are arranged horizontally. To calibrate, set zoom, focus,
iris, and pan position for easy side-by-side comparison and set each fixture to the same tilt DMX value.
Select one fixture to be the reference fixture. On the other fixtures, select U TI L /C A L/ T OF and press
[Enter]. Adjust the offset as necessary to align the beam with the reference beam. Press [Enter] to save the
setting.
5
To calibrate the dimmer, select U TI L /C AL / D O F and press [Enter]. Hold a piece of paper over the
lens. Set the offset to 0 and then increase it until light is clearly projected onto the paper. Press [Enter] to
save the setting. Remove the paper.
6
To calibrate color mixing flags (cyan, magenta, yellow, and color temperature correction), project white
beams with no dimming and position them for easy comparison. On each fixture, including the reference,
select U TI L /C A L/ C O F and press [Enter]. (This adds a defined amount of cyan.) Select one fixture to
be the reference. Adjust the offsets on the other fixtures to match the reference color. Press [Enter] to save
the setting. Repeat for M OF (magenta), Y OF (yellow), and C TO F (CTC).
7
Focus calibration is useful when two or more fixtures are the same distance from a projection surface. To
calibrate focus, set up all fixtures with the same focus, zoom, dimming, iris, and gobo values. Select a
focussed fixture to be the reference. On the other fixtures, select UT IL / CA L/ F OO F and press [Enter].
Adjust the offset to focus the image. Press [Enter] to save the setting.
Software upload
The software update mode is normally engaged automatically by the upload device. See Software installation on
page 23.
16
MAC 2000 Profile II
OPTICAL
CONFIGURATION
Gobos
Specifications
All gobo slots including the seven color/gobo wheel positions accept round theatrical size-E glass gobos. Aluminum
gobos are suitable for short-term use only. For best results, custom gobos should meet the following criteria.
Outside diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37.5 +0/-0.3 mm (1 15/32 +0/-0.01 in.)
Maximum image diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 mm (1 3/16 in.)
Material: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . High temperature Borofloat or better glass
Coating: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Dichroic or enhanced aluminum
The color/gobo wheel accepts 1.1 mm thick gobos and color filters. Thinner gobos must be secured with a drop or two
of glue. Use a high-temperature silicone adhesive such as Dow Corning’s 732 Multi-Purpose Sealant.
The rotating-gobo wheel positions hold gobos up to 3 mm thick with the gobo retention spring. Gobos thicker than 3
mm must be glued in the holder.
Orientation
Coated gobos are inserted with the coating against the rim of the holder (away from the spring). Textured gobos are
inserted with the smooth side against the spring. This provides the best results when combining rotating gobos.
Coated side
Uncoated side
When an object is held up to the coated side
there is no space between the object and its
reflection. The back edge of the gobo cannot
be seen when looking through the coated
side.
When an object is held up to the uncoated
side there is a space between the object and
its reflection. The back edge of the gobo can
be seen when looking through the uncoated
side.
Figure 13: Finding the coated side
Rotating gobo wheels
Figure 14 shows the standard gobo configuration.
1
5
1
1
5
red
2
2 2
4
3
Gobo wheel 1
7
4
3
Gobo wheel 2
6
green
blue
3
UV
4
5
Color/gobo wheel
Figure 14: Standard gobo configuration as seen from lamp
Optical configuration
17
Replacing rotating gobos
Important! The gobo can fall out if the spring is inserted backwards.
1
Disconnect the fixture from power and allow it to cool.
2
See Figure 15. Lock the head in the upside down position and remove the bottom cover. Turn the gobo
wheels as required to access the desired position. Pull the gobo holder away from the wheel slightly to
release. Remove the gobo holder.
3
Remove the gobo retention spring from the gobo holder and drop the gobo out of the holder. Insert the new
gobo in the holder. Insert the spring with the narrow end against the gobo. To identify the narrow end, press
the spring flat: the narrow end is on the inside. Push the end of the spring in under the lip of the holder.
4
Work the rim of the gobo holder under both clips and snap the gobo holder back into position. If necessary,
a small screwdriver or similar tool may be used to pry the clips away from the wheel.
5
Replace the bottom cover and release the pan and/or tilt locks before operating.
Color/gobo wheel
The color/gobo wheel houses four dichroic glass color filters and three static gobos as shown in Figure 14. These are
normally installed with the coated side in towards the wheel.
Replacing color filters or gobos
1
Disconnect the fixture from power and allow it to cool.
TOP
Access gobos from the bottom of the head. Tilt out
and remove the holder.
coated side
The narrow end is on the inside when
the spring is pressed flat.
Insert spring with narrow end against gobo.
Figure 15: Replacing rotating gobos
18
MAC 2000 Profile II
2
Lock the head in the upside down position and remove the bottom cover. Turn the color/gobo wheel as
required to access the desired position.
3
To remove, press the filter or gobo from the lamp side to release it. Remove from wheel.
4
To insert, work the filter or gobo under the retention spring and position it between the pins. The long edge
of the six-sided color filters must be precisely aligned with the inside of the hub in order to fit.
5
Replace the bottom cover and unlock the head before operating.
Install filters and
gobos with
coating down,
towards the
lamp.
Figure 16: Replacing color filters and fixed gobos
Effect wheel
The effect wheel provides two positions for rotating effects. Effects are glued into holders and are changed by
replacing the assembled effect and holder.
Replacing rotating effects
1
Disconnect the fixture from power and allow it to cool.
2
Lock the head in the upside down position and remove the bottom cover. Turn the effect wheel so that the
locking plate is under the sensor bracket.
3
To remove, hold the rim of the effect holder and pull back on the locking plate. Remove effect from wheel.
4
To insert, pull back on the locking plate. If both effects are removed, pull straight back on both tabs. Position
the groove in the effect holder over the fixed plate. Release the locking plate and verify that the effect is
properly seated.
5
Replace the bottom cover and unlock the head before operating.
Position the effect holder
groove over the fixed plate.
Locking plate
Figure 17: Replacing rotating effects
Optical configuration
19
EFFECTS
The MAC 2000 Profile II is compatible with USITT DMX512 controllers. The fixture has two DMX operating modes,
8-bit and 16-bit.16-bit mode requires four more DMX channels than 8-bit mode but provides more precise gobo
indexing and pan/tilt positioning. All other functions are identical. The complete DMX protocol begins on page 24.
Dimming and strobe
The mechanical dimmer/shutter system provides smooth, high-resolution 100 percent dimming, instant open and
blackout, random and variable strobe effects up to 10 Hz, and random and variable pulses in which the dimmer snaps
open and slowly dims or snaps closed and slowly opens.
Color mixing
The color mixing system uses continuous dichroic cyan, magenta, and yellow (CMY) color filters. It is a subtractive
system that removes color from white light. Inserting all three filters results in loss of light: for maximum brightness,
mix 2 colors at a time.
Color temperature correction
The color temperature correction (CTC) system uses a continuous 0 - 178 mireds color filter that lowers the color
temperature from 6000 K to 2900 K.
Random color mixing
Variable speed random color mixing using the CMY filters may be selected at the top of channel 7. When selected,
channels 3 - 5 set the maximum or minimum amount of each color in the mix. Values up to 127 set a minimum
amount: the color is randomly inserted from the selected value up to 100%. Values over 127 set a maximum amount:
the color is inserted from 0% up to the selected value. To use the full range of a color in the random mix, select a
minimum value of 0% or a maximum value of 100%. To exclude a color from the random mix, select a maximum
value of 0%.
Fixed colors and gobos
The color/gobo wheel provides seven slots with four dichroic color filters and three glass gobos. To change the color or
gobo, see Replacing color filters or gobos on page 18.
The wheel can be scrolled, allowing for split color effects, snapped to fixed positions, and continuously rotated in both
directions at different speeds. When the effects speed channel is set from 252 to 255, the dimmer automatically closes
while the color wheel is moving between static positions.
Gobos
Two overlapping gobo wheels provide room for 10 glass gobos. See page 17 to change gobos.
Gobos may be rotated and shaken at varying speeds and indexed to any position. Extremely accurate positioning is
available in 16-bit mode.
For each wheel, the gobo and type of rotation (indexed or continuous, with or without shake) are selected on the
wheel’s Gobo & Function Channel, which also provide commands for continuous wheel rotation. The gobo position
index and rotation speed are selected on its Position/Velocity Channel. In 16-bit mode, the position is further adjusted
on the wheel’s Fine Position Channel.
20
MAC 2000 Profile II
Effect wheel
The effect wheel provides a variable frost filter and two rotating slots that house a beam shaper and a three-facet prism.
The position and velocity of the rotating slots are selected on the effect wheel’s Position / Velocity Channel.
Iris
The iris closes down to 15 percent of its full-open diameter with high, 200-step resolution. The Iris Channel also
provides random and variable speed pulsating iris effects.
Focus and zoom
The focus lens focusses the beam from approximately 2 meters (6.5 feet) to infinity. The zoom lens widens the beam
from approximately 10° at full spot to 28° at full flood.
Pan and tilt
The yoke pans 540° and the head tilts 267°. For maximum positioning accuracy, select 16-bit mode.
The pan/tilt speed (fast, norm, or slow) may be selected on the pan/tilt speed channel. Setting the pan/tilt speed channel
to “blackout” causes the shutter to black out the light while the head is moving.
Speed control
There are two ways to control the speed at which effects move from one static position to another. These are known as
tracking control and vector control and are selected on the Pan/Tilt Speed and Effect Speed Channels. These channels
are independent so you may, for example, combine a vector control pan movement with a tracking control color fade.
In tracking mode, speed is determined by the cross-fade time. The controller continuously sends small position
changes that the fixture “tracks.” To enable tracking mode, set the relevant speed channel to a tracking value. Note that
in addition to enabling tracking control, some tracking values also provide overrides of the menu settings.
In vector mode, speed is set directly on a speed channel. The cross-fade time must be 0. Vector control provides a way
to set speed on controllers that do not have programmable fade times and results in smooth movement regardless of the
cross-fade time or the controller’s processing power.
To open the iris slowly in:
• Tracking mode, for example, you program a scene with the iris fully closed and a second scene with the iris fully open.
Then you set a cross-fade time between the two scenes of, say, 10 seconds. The controller gradually changes the iris
position value from 199 (closed) to 0 (open).
• Vector mode, you program the iris closed and open as before. Then you set the cross-fade time to 0 and program a slow
speed, in the second scene, on the Effect Speed Channel.
Effects
21
ROUTINE
MAINTENANCE
The MAC 2000 Profile II requires routine cleaning. The schedule depends heavily on the operating environment;
please consult a Martin service technician for recommendations. Refer all service not described here to a qualified
Martin technician.
Important! Excessive dust, smoke fluid, and particulate buildup degrades performance and causes
overheating and damage to the fixture that is not covered by the warranty.
Warning!
Disconnect the fixture from power before removing any cover.
Cleaning
Use care when cleaning optical components and work in a clean, well lit area. The coated surfaces are fragile and
easily scratched. Do not use solvents that can damage plastic or painted surfaces.
Inspect the air filters regularly and clean before they become clogged. Replace the air filters with new ones when
replacing the lamp.
To maintain adequate cooling, dust must be cleaned from the fans and air vents periodically.
Cleaning optical components
1
Disconnect the fixture from power and allow the components to cool completely. Remove the head cover.
2
Vacuum or gently blow away dust and loose particles with compressed air.
3
Remove stuck particles with an unscented tissue or cotton swab moistened with glass cleaner or distilled
water. Do not rub the surface: lift the particles off with a soft repeated press.
4
Remove smoke and other residues with cotton swabs or unscented tissues moistened with isopropyl
alcohol. A commercial glass cleaner may be used, but residues must be removed with distilled water. Clean
with a slow circular motion from center to edge. Dry with a clean, soft and lint-free cloth or compressed air.
Cleaning the fan and air vents
• Remove dust from the fans and air vents with a soft brush, cotton swab, vacuum, or compressed air.
Cleaning or replacing the air filters
1
Disconnect the fixture from power. On each side of the head, remove the 2 screws that hold the side cover
using a Torx-20 screwdriver. Slide the cover forward to remove. Lift the filter off of the cover.
2
Clean the filters with a vacuum or compressed air, or replace them. If they are saturated with smoke fluid,
etcetera, soak them in warm soapy water and blot dry.
3
Place the filters on the covers and replace the covers.
Figure 18: Removing air filters
22
MAC 2000 Profile II
Software installation
Software updates are installed in the MAC 2000 Profile II using a Martin MP-2 Uploader or a LightJockey 4064 DMX
interface card. The procedure is found in the MP-2 user manual and the Martin Software Uploader online help file.
Requirements
The following are required in order to install software.
• The MAC 2000 Profile II update file, available for download from the User Support Area of the Martin web site
(http://www.martin.dk).
• The Martin Software Uploader program, version 4.0 or later, available for download from the User Support Area of the
Martin web site.
• A Martin MP-2 Uploader connected to a Windows 95/98/ME/2000/XP PC, or a LightJockey DMX Interface card.
Preventing software updates on a MAC 2000 Profile II
Software updates are enabled by default, but on a MAC 2000 Profile II you can disable this by setting the Write jumper
(see Circuit board connections on page 36) to disable.
Boot sector jumper
If the normal upload procedure does not work, or if the software update notes call for a boot sector update, move the
boot sector jumper on the printed circuit board to the BOOT position before uploading software.
SETTING
THE BOOT SECTOR JUMPER
1 Disconnect the fixture from power.
2 Remove the top screws from the ends of the front side panel and tilt the
panel down to expose the main circuit board.
3 Using the appropriate diagram in Circuit board connections on page 36 or
the label inside the base, locate the BOOT jumper. This is PL16 on a MAC
2000 Profile II. Move the jumper to the “BOOT” position.
4 Perform a boot mode upload. When the upload is complete, disconnect the
fixture from power and move the jumper back to the locked or normal
position.
Routine maintenance
23
DMX
PROTOCOL
DMX channel
Start code = 0
8-bit
16-bit
1
1 If reset is disabled, i.e., d RE S =O F F,
the command executes only when
position 7 is selected on the color
wheel and gobo 5 is selected on both
gobo wheels.
2
If lamp off is disabled, i.e.,
dLOF =OFF, the command executes
only when position 7 is selected on the
color wheel and gobo 5 is selected on
both gobo wheels.
2
Value
Percent
0 - 19
20 - 49
50 - 72
73 - 79
80 - 99
100 - 119
120 - 127
128 - 147
148 - 167
168 - 187
188 - 190
191 - 193
194 - 196
197 - 199
200 - 202
203 - 207
208 - 217
218 - 227
228 - 237
238 - 247
248 - 255
0-7
8 - 19
20 - 28
29 - 31
31 - 39
39 - 47
47 - 50
50 - 58
58 - 65
66 - 73
74 - 75
75 - 76
76 - 77
77 - 78
78 - 79
80 - 81
82 - 85
85 - 89
89 - 93
93 - 97
97 - 100
Shutter, Strobe, Reset, Lamp On/Off
Shutter closed
Shutter open
Strobe, fast!slow
Shutter open, lamp power reduced (MAC 2000 E only)
Opening pulse, fast !slow
Closing pulse, fast !slow
Shutter open
Random strobe, fast
Random strobe, medium
Random strobe, slow
Shutter open
Random opening pulse, fast
Random opening pulse, slow
Random closing pulse, fast
Random closing pulse, slow
Shutter open
Reset fixture1
Shutter open
Lamp power on
Shutter open
Lamp power off (hold 5 seconds)2
0 - 255
0 - 100
Intensity
0 ! 100%
0 - 255
0 - 100
Cyan
White ! Cyan
0 - 127
128 - 255
0 - 50
50 -100
Cyan limit for random CMY color
At least 0 ! 100%
At most 0 ! 100%
0 - 255
0 - 100
Magenta
White ! Magenta
0 - 127
128 - 255
0 - 50
50 -100
Magenta limit for random CMY color
At least 0 ! 100%
At most 0 ! 100%
0 - 255
0 - 100
Yellow
White ! Yellow
0 - 127
128 - 255
0 - 50
50 -100
Yellow limit for random CMY color
At least 0 ! 100%
At most 0 ! 100%
0 - 255
0 - 100
CTC
Cold ! Warm (0-178 mireds)
3
4
5
6
Function
Table 3: DMX protocol
24
MAC 2000 Profile II
DMX channel
Start code = 0
8-bit
16-bit
7
Value
Percent
Function
0 - 20
20 - 40
40 - 60
60 - 80
80 - 100
100 - 120
120 - 140
140 - 160
0-7
7 - 16
16 - 23
23 - 31
31 - 39
39 - 47
47 - 55
55 - 63
Color/Gobo Wheel
Continuous scroll
White ! Position 1
Position 1 ! Position 2
Position 2 ! Position 3
Position 3 ! Position 4
Position 4 ! Position 5
Position 5 ! Position 6
Position 6 ! Position 7
Position 7 ! Open
160 - 163
164 - 167
168 - 171
172 - 175
176 - 179
180 - 183
184 - 187
188 - 191
63 - 64
64 - 65
66 - 67
67 - 68
69 - 70
70 - 72
72 - 73
74 - 75
Stepped scroll
Position 7 (Dots)
Position 6 (Highways)
Position 5 (Triple Cone)
Position 4 (UV)
Position 3 (Blue 111)
Position 2 (Green 201)
Position 1 (Red 308)
Open
192 - 217
218- 243
75 - 85
85 - 95
Continuous rotation
CW, fast ! slow
CCW, slow ! fast
244 - 247
248 - 251
252 - 255
96 - 97
97 - 98
99 - 100
Random CMY color (set limits on ch. 3 - 5)
Random color, fast
Random color, medium
Random color, slow
0-9
0-3
10 - 14
15 - 19
20 - 24
25 - 29
30 - 34
3-5
5-7
7-9
9 - 11
11 - 13
Indexed gobo rotation
Gobo 1 (Jet Fan)
Gobo 2 (Pipe Dreams)
Gobo 3 (Double Worms)
Gobo 4 (Inverted King Star)
Gobo 5 (Limbo)
35 - 39
40 - 44
45 - 49
50 - 54
55 - 59
13 - 15
15 - 17
17 - 19
19 - 21
21 - 23
Continuous gobo rotation
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
60 - 74
75 - 89
90 - 104
105 - 119
120 - 134
23 - 29
29 - 35
35 - 40
41 - 46
47 - 52
Indexed gobo shake
Gobo 1, shake slow ! fast
Gobo 2, shake slow ! fast
Gobo 3, shake slow ! fast
Gobo 4, shake slow ! fast
Gobo 5, shake slow ! fast
135 - 149
150 - 164
165 - 179
180 - 194
195 - 209
53 - 58
59 - 64
65 - 70
70 - 76
76 - 82
Rotating gobo shake
Gobo 1, shake slow ! fast
Gobo 2, shake slow ! fast
Gobo 3, shake slow ! fast
Gobo 4, shake slow ! fast
Gobo 5, shake slow ! fast
210 - 232
233 - 255
82 - 91
91 - 100
Gobo wheel rotation
CW, slow ! fast
CCW, fast ! slow
8
Gobo Wheel 1, Gobo & Function
Open
Set position / velocity on
next channel. Fine
position on ch. 10
(16-bit).
Table 3: DMX protocol
DMX protocol
25
DMX channel
8-bit
Start code = 0
16-bit
9
9
-
10
10
Value
Percent
0 - 255
0 - 100
Gobo Wheel 1, Position/Velocity
Coarse Position (MSB), Min ! Max
0-2
3 - 127
128 - 252
253 - 255
0-1
1 - 50
50 - 98
99 - 100
Rotation velocity
No rotation
CCW, slow ! fast
CW, fast ! slow
No rotation
0 - 255
0 - 100
Gobo Wheel 1, Fine Position
Fine Position (LSB), Min ! Max
0-9
0-3
10 - 14
15 - 19
20 - 24
25 - 29
30 - 34
3-5
5-7
7-9
9 - 11
11 - 13
Indexed gobo rotation
Gobo 1 (Limbo Donut)
Gobo 2 (Triangle Cones)
Gobo 3 (Congo Star)
Gobo 4 (Space Sun)
Gobo 5 (Waves)
35 - 39
40 - 44
45 - 49
50 - 54
55 - 59
13 - 15
15 - 17
17 - 19
19 - 21
21 - 23
Continuous gobo rotation
Gobo 1
Gobo 2
Gobo 3
Gobo 4
Gobo 5
60 - 74
75 - 89
90 - 104
105 - 119
120 - 134
23 - 29
29 - 35
35 - 40
41 - 46
47 - 52
Indexed gobo shake
Gobo 1, shake slow ! fast
Gobo 2, shake slow ! fast
Gobo 3, shake slow ! fast
Gobo 4, shake slow ! fast
Gobo 5, shake slow ! fast
135 - 149
150 - 164
165 - 179
180 - 194
195 - 209
53 - 58
59 - 64
65 - 70
70 - 76
76 - 82
Rotating gobo shake
Gobo 1, shake slow ! fast
Gobo 2, shake slow ! fast
Gobo 3, shake slow ! fast
Gobo 4, shake slow ! fast
Gobo 5, shake slow ! fast
210 - 232
233 - 255
82 - 91
91 - 100
Gobo wheel rotation
CW, slow ! fast
CCW, fast ! slow
0 - 255
0 - 100
Gobo Wheel 2, Position/Velocity
Coarse Position (MSB), Min ! Max
0-2
3 - 127
128 - 252
253 - 255
0-1
1 - 50
50 - 98
99 - 100
Rotation velocity
No rotation
CCW, slow ! fast
CW, fast ! slow
No rotation
0 - 255
0 - 100
Gobo Wheel 2, Fine Position
Fine Position (LSB), Min ! Max
11
11
12
-
13
Function
Gobo Wheel 2, Gobo & Function
Open
Table 3: DMX protocol
26
MAC 2000 Profile II
Set position / velocity on
next channel. Fine
position on ch. 13
(16-bit).
DMX channel
8-bit
12
13
Start code = 0
16-bit
15
16
15
17
16
18
17
19
-
20
18
21
-
22
20
Percent
Function
0
1 - 175
176 - 183
184 - 191
192 - 199
200 - 207
208 - 215
0
1 - 68
69 - 72
72 - 75
75 - 78
78 - 81
81 - 84
Effect Wheel Selection and Macros
Effect selection
Open
Variable frost, 0 ! 100%
Effect 1, indexed rotation
Set position / velocity
Effect 2, indexed rotation
on next channel.
Effect 1, continuous rotation
Effect 2, continuous rotation
Open
216 - 220
221 - 225
226 - 230
231 - 235
236 - 240
241 - 245
246 - 250
251 - 255
85 - 86
87 - 88
89 - 90
91 - 92
92 - 94
94 - 96
96 - 98
98 - 100
Macro selection
1
2
3
4
5
6
7
8
0 - 255
0 - 100
Effect Wheel, Position / Velocity
Position, Min ! Max
0-2
3 - 127
128 - 252
253 - 255
0-1
1 - 50
50 - 98
99 - 100
Rotation velocity
No rotation
CCW, slow ! fast
CW, fast ! slow
No rotation
0 - 199
200 - 215
216 - 229
230 - 243
244 - 246
247 - 249
250 - 252
253 - 255
0 - 78
78 - 84
85 - 90
90 - 95
96 - 96
97 - 98
98 - 99
99 - 100
Iris
Open ! closed
Closed
Pulse opening, fast !slow
Pulse closing, fast !slow
Random pulse opening, fast
Random pulse opening, slow
Random pulse closing, fast
Random pulse closing, slow
0 - 255
0 - 100
Focus
Infinity ! near
0 - 255
0 - 100
Zoom
Flood ! spot
0 - 255
0 - 100
Pan Coarse (MSB)
Left ! right (128 = neutral)
0 - 255
0 - 100
Pan Fine (LSB)
Left ! right
0 - 255
0 - 100
Tilt Coarse (MSB)
Up ! down (128 = neutral)
0 - 255
0 - 100
Tilt Fine (LSB)
Up ! down
0-2
3 - 242
243 - 245
246 - 248
249 - 251
252 - 255
0
1 - 95
95 - 96
96 - 97
98
99 - 100
Pan/Tilt Speed
Tracking
Fast ! slow
Tracking, PTSP = SLOW (slow pan/tilt speed)
Tracking, PTSP = NORM (normal pan/tilt speed)
Tracking, PTSP = FAST (fast pan/tilt speed)
Blackout
0-1
1 - 94
94 - 95
95 - 96
96 - 97
98 - 98
99 - 100
Effect Speed (Dimmer, Color, Gobos, Effects,
Indexed Rotation, Iris, Focus, and Zoom)
Tracking
Fast ! slow
Tracking, STUd = OFF (studio mode off)
Tracking, STUd = ON (studio mode on)
Tracking, SCUT = OFF (shortcuts off)
Tracking, SCUT = ON (shortcuts on)
Fast. Blackout “speed” for color wheel
14
14
19
Value
23
24
0-2
3 - 239
240 - 242
243 - 245
246 - 248
249 - 251
252 - 255
Table 3: DMX protocol
DMX protocol
27
CONTROL
MENU
Menu
Item
Options
Notes (Default settings in bold print)
A dd R
-
1 - 51 2
DMX address
8b it
Full control with coarse pan, tilt, and gobo indexing
P SE T
16 bt
Full control with fine pan, tilt, and gobo indexing
ON
Map DMX pan control to tilt channel and vice versa.
OF F
Normal pan and tilt control
ON
Reverse DMX pan control, right ! left
OF F
Normal pan control, left ! right
ON
Reverse DMX tilt control, down ! up
OF F
Normal tilt control, up ! down
NO RM
Medium pan/tilt speed
FA ST
Optimize movement for speed
SL OW
Optimize movement for smoothness
OF F
Optimize effects for speed
ON
Optimize effects for silence
ON
Display remains on
OF F
Display extinguishes 2 minutes after last key press
10 - 1 0 0
Adjust display intensity
ON
Enable DMX lamp off command
OF F
Disable DMX lamp off command
ON
Enable DMX reset command
OF F
Disable DMX reset command
ON
Lamp strikes automatically within 90 seconds of power on
OF F
No automatic lamp strike
dM X
Lamp strikes if DMX is present, douses 15 mins. after it’s missing
ON
Color, gobo, and effect wheels turn shortest distance
OF F
Color, gobo, and effect wheel paths oscillate
MO dE
MOd1: Absolute delta value algorithm (for most controllers)
moD2: Real delta value algorithm
S WA P
P AT I
P IN V
T IN V
P TS P
S tu d
-
-
d IS P
d IN T
d LO F
d RE S
A LO N
P ER S
S CU T
T RA C
CA L
(Default = 6)
NO RM
Normal color/gobo wheel speed.
FA ST
Increases gobo/color wheel acceleration to maximum and provides
faster color bumps. Note that gobo/color wheel step loss my occur
under low power or high temperature conditions that decrease
motor torque. The NORM option is slower, but less prone to step
loss.
F AC T
LO AD
Return all personality settings (not calibrations) to factory defaults
C US 1, C US 2,
C US 3
LO Ad
Load custom configuration
SA VE
Save current configuration
C SP d
d FS E
1- 1 0. Tracking samples. Increase if pan/tilt is not smooth.
Table 4: Control menu
28
MAC 2000 Profile II
Menu
Item
Options
Notes (Default settings in bold print)
TO TL
Total hours of operation since fabricated
RS ET
Hours of operation since counter reset. To reset, display counter
and press [↑] for 5 seconds.
TO TL
Total hours of operation with lamp on since fabricated
RS ET
Lamp hours since counter reset. To reset, display counter and
press [↑] for 5 seconds.
TO TL
Total number of lamp strikes since fabricated
RS ET
Number of lamp strikes since counter reset. To reset, display
counter and press [↑] for 5 seconds.
HE Ad
Head temperature
bA SE
Base temperature
-
CPU firmware version
ST CO
Decimal value of the DMX start code. The start code must be 0 for
the MAC 2000 Profile II to function properly.
dI M. . E SP
DMX value (from 0 - 255) received for each channel.
T IM E/ H RS
T IM E/ L H R
I NF O
T IM E/ L S T
T EM P
V ER
d MX L
-
Table 4: Control menu
Control menu
29
Menu
Item
Options
Notes (Default settings in bold print)
R ST
-
Reset fixture
L ON
-
Lamp on
L oF F
-
Lamp off
OP EN
Open shutter
CL OS
Close shutter
ST RF
Fast strobe
ST RM
Medium strobe
ST RS
Slow strobe
d IM
0- 25 5
Dimmer
C YA N,
M AG ,Y E L
0- 25 5
C TC
0- 25 5
Color temperature correction. Cold →Warm (0-178 mireds)
OP EN
Color wheel in open position.
C1 -C 7
Color wheel positions 1 →7.
CW F
Clockwise rotation - fast
CC WF
Counter clockwise rotation - fast
CW M
Clockwise rotation - medium
CC WM
Counter clockwise rotation - medium
CW S
Clockwise rotation - slow
CC WS
Counter clockwise rotation - slow
RN dF
Random color - fast
RN dM
Random color - medium
RN dS
Random color - slow
OP EN
Gobo wheel 1. Open position
g1 I - g5 I
Gobo wheel 1. Indexed gobos 1→5
g1 g - g5 R
Gobo wheel 1. Rotating gobos 1→5
g1 IS - g5 IS
Gobo wheel 1. Indexed gobo shake 1→5
g1 RS - g5 RS
Gobo wheel 1. Rotating gobo shake 1→5
CW F
Gobo wheel 1. Clockwise rotation - fast
CC WF
Gobo wheel 1. Counter clockwise rotation - fast
CW M
Gobo wheel 1. Clockwise rotation - medium
CC WM
Gobo wheel 1. Counter clockwise rotation - medium
CW S
Gobo wheel 1. Clockwise rotation - slow
CC WS
Gobo wheel 1. Counter clockwise rotation - slow
0- 25 5
Clockwise rotation of gobo wheel 1. Slow→fast.
S HU T
M AN
C OL
g Ob 1
I /S 1
White →Cyan/Magenta/Yellow
Table 4: Control menu
30
MAC 2000 Profile II
Menu
Item
Options
Notes (Default settings in bold print)
OP EN
Gobo wheel 2. Open position
g1 I - g5 I
Gobo wheel 2. Indexed gobos 1→5
g1 g - g5 R
Gobo wheel 2. Rotating gobos 1→5
g1 IS - g5 IS
Gobo wheel 2. Indexed gobo shake 1→5
g1 RS - g5 RS
Gobo wheel 2. Rotating gobo shake 1→5
CW F
Gobo wheel 2. Clockwise rotation - fast
CC WF
Gobo wheel 2. Counter clockwise rotation - fast
CW M
Gobo wheel 2. Clockwise rotation - medium
CC WM
Gobo wheel 2. Counter clockwise rotation - medium
CW S
Gobo wheel 2. Clockwise rotation - slow
CC WS
Gobo wheel 2. Counter clockwise rotation - slow
0- 25 5
Clockwise rotation of gobo wheel 2. Slow→fast.
F 0- F 17 5
Effects. Variable frost 0→100%
E1 I - E2 I
Effect 1 or 2 - indexed rotation.
E1 R - E2 R
Effect 1 or 2 - continuous rotation.
ST OP
Effect wheel - no rotation.
R 1- R 12 5
Effect wheel - clockwise rotation. Slow→fast.
L1 25 - L 1
Effect wheel - counter clockwise rotation. Fast→slow.
ST OP
Effect wheel - no rotation.
I 0- I 19 9
Iris - Open→Closed
PO UT
Pulse opening
P IN
Pulse closing
RN dO
Random pulse opening
RN dI
Random pulse closing
F OC
0- 25 5
Focus - Infinity→Near
Z OO M
0- 25 5
Zoom - Flood→spot
P AN
0- 25 5
Pan - Left→Right
T IL T
0- 25 5
Tilt - Up→Down
-
RU N
Run a general test of all effects
g Ob 2
I /S 2
M AN
c on t .
E FF
I /S E
I RI S
T SE Q
Table 4: Control menu
Control menu
31
Menu
Item
Options
Notes (Default settings in bold print)
ON
Enable pan/tilt position correction system
OF F
Disable pan/tilt feedback. Setting not saved.
ON
Enable on the fly reset of color, gobo, and effect wheels
OF F
Disable on the fly reset of color, gobo, and effect wheels
A dj
-
See Table 5
C AL /P OF
1- 25 5
Pan offset
C AL /T OF
1- 25 5
Tilt offset
C AL /d OF
1- 25 5
Dimmer offset
C AL /C OF
1- 25 5
Cyan offset
C AL /M OF
1- 25 5
Magenta offset
C AL /Y OF
1- 25 5
Yellow offset
C AL /C T OF
1- 25 5
CTC offset
C AL /C O OF
1- 25 5
Color wheel offset
C AL /G 1 OF
1- 25 5
Gobo wheel 1 offset
C AL /G 2 OF
1- 25 5
Gobo wheel 2 offset
C AL /E F OF
1- 25 5
Effect wheel offset
C AL /I R OF
1- 25 5
Iris offset
C AL /F O OF
1- 25 5
Focus offset
C AL /Z O OF
1- 25 5
Zoom offset
d FO F
SU RE
Return all offsets to the default settings
P Cb T
LE d
PCB test for service use only.
RE G
Regulate the effect cooling fans for quieter performance. Enabling
this option increases the operating temperature and thus increases
wear on the components.
FU LL
Operate cooling fans at full speed. This is the default from software
version 1.4.
SU RE
Manually set fixture to software update mode
F Eb A
E FF b
U TI L
( P re s s
a nd h ol d
En ter fo r a
few
seconds
to use this
m enu )
F AN S
U PL d
R ep la c e la m p
Displayed when lamp hours exceed average life (750 hours)
F ix tu r e ov e rh e at in g
Displayed if head temperature exceeds 120° C (248° F)
S MS G
Table 4: Control menu
32
MAC 2000 Profile II
ADJUSTMENT
SUBMENU
This menu is located under UT IL / Ad j .
Menu
Item
Options
Notes
RS T
-
-
Reset fixture
L ON
-
-
Strike lamp
Lo FF
-
-
Douse lamp
Ad j
Turn dimmer to adjustment position (closed mechanical stop)
OP EN
Open dimmer
CL OS
Close dimmer
ST RO
Strobe
MI N
Color flags out
MA X
Color flags in
OP EN
Turn color wheel to open position
Ad j
Turn color wheel to adjustment position
C1 -C 7
Select color
OP EN
Turn gobo wheel to open position
Ad j
Turn gobo wheel 1 to adjustment position
G1 I - G5 I
Turn gobos to index position
G1 -G 5 LS
Select and rotate gobos
OP EN
Turn effect wheel to open position
Ad j
Turn effect wheel to adjustment position
FR OS
Turn effect wheel to maximum frost position
EF F1 - E2 L S
Select and rotate effects
Ad j
Set iris to adjustment position (open mechanical stop)
OP EN
Open iris
CL OS
Close iris
NE AR
Move focus lens to front
FA R
Move focus lens to back
NA RR
Zoom to full spot
WI dE
Zoom to full flood
NE UT
Move pan and tilt to neutral positions
PN Td
Pan neutral, tilt down
PN TU
Pan neutral, tilt up
PL TN
Pan left, tilt neutral
PR TN
Pan right, tilt neutral
PL Td
Pan left, tilt down
PR TU
Pan right, tilt up
d IM
C YA N , M AG ,
Y EL , C TC
C OL
G Ob 1 , GO b 2
HE Ad
E FF
I RI S
F OC U
Z OO M
PA TI
-
Table 5: Adjustment menu
Adjustment submenu
33
DISPLAY
MESSAGES
Message
Appears when...
RS T ( Reset)
... the fixture is indexing effects at startup.
Wait for reset to complete.
SR ST (Serial reset)
... the fixture has received a reset command
from the controller.
Wait for reset to complete. Set
PERS/dRES to off to prevent accidental
reset commands.
HO ME
... the effects have been indexed and are
moving to their default positions.
Wait a few moments.
OP EN
...the lamp access cover is not fully closed.
Verify that the lamp access cover is locked
in place.
LE RR (Lamp error)
... the lamp doesn’t ignite within 10 minutes of
receiving the ‘Lamp ON’ command. Likely
reasons are a missing or defective lamp, or
insufficient AC voltage.
Check the lamp. Check that the voltage
and frequency settings match the local
supply.
ME RR (Memory error)
...the EEPROM memory cannot be read.
Contact Martin service personnel for
assistance.
Sh ER (Short error)
... the fixture detects the lamp is ON but no
‘Lamp ON’ command has been received. This
can occur if the lamp relay is stuck or if the
lamp-power feedback circuit fails. The fixture
may be operated but remote lamp on/off may
be effected.
Contact Martin service personnel for
assistance.
bT ER (Base temperature error)
HT ER (Head temperature error)
... there is a fault with the temperature sensor
in the base or head.
Contact Martin service personnel for
assistance.
Fb EP (Feedback error pan)
Fb ET (Feedback error tilt)
Fb ER (Feedback error pan/tilt)
...pan (FbEp), tilt (FbET) or both (FbER)
feedback circuits are malfunctioning. It will still
be possible to operate the fixture, though it
goes into a “safe” mode where maximum
speed is reduced, thus preventing the fixture
from losing track of its home position (losing
step).
Contact Martin service personnel for
assistance.
(Pan time-out)
(Tilt time-out)
(Cyan time-out)
(Magenta time-out)
(Yellow time-out)
(CTC time-out)
(Focus time-out)
(Zoom time-out)
...the electric indexing circuit is
malfunctioning. The fixture will, after the
time-out, establish a mechanical stop, and
continue to work normally.
Reset fixture again. Contact Martin
service personnel if problem continues.
(Color wheel time-out)
(Gobo wheel 1 time-out)
(Gobo wh. 1 index time-out)
(Gobo wheel 2 time-out)
(Gobo wh. 2 index time-out)
(Effect wheel time-out)
(Effect wheel index time-out)
...the magnetic-indexing circuit malfunctions
(e.g. sensor defective or magnet missing).
After the time-out, the effect in question stops
in a random position.
Reset fixture again. Contact Martin
service personnel if problem continues.
(Gobo wh. sensor short)
(Gobo rot. sensor short)
(Effect wh. sensor or
zoom/focus switch short)
(Color wh. or effect rot.
sensor short)
(Yellow or CTC switch short)
(Cyan or magenta switch
short)
...an effect does not move away from the index
position under reset, a sensor or micro-switch
circuit is shorted, or a micro-switch is stuck or
connected incorrectly.
Contact Martin service personnel for
assistance.
PA ER
TI ER
CY ER
MA ER
YE ER
CT ER
FO ER
ZO ER
CO ER
g1 ER
R1 ER
g2 ER
R2 ER
EF ER
RE ER
S3 SC
S4 SC
S5 SC
S6 SC
S7 SC
S8 SC
Table 6: Display messages
34
MAC 2000 Profile II
What to do
TROUBLESHOOTING
Problem
One or more of the fixtures is
completely dead.
Fixtures reset correctly but
respond erratically or not at all
to the controller.
Magnetically indexed effect
resets correctly but wanders
after fixture reaches operating
temperature.
Mechanical effect loses
position.
No light and “LERR” error
message displayed.
Probable cause(s)
Remedy
No power to fixture.
Check that power is switched on and cables are
plugged in.
Primary fuse blown (located near mains inlet).
Disconnect fixture and replace fuse.
Secondary fuse(s) blown (located on PCB
inside base).
Disconnect fixture. Check fuses on PCB and
replace.
Bad data link.
Inspect connections and cables. Correct poor
connections. Repair or replace damaged cables.
Data link not terminated.
Insert termination plug in output jack of the last
fixture on the link.
Incorrect addressing of the fixtures.
Check fixture address and protocol settings.
One of the fixtures is defective and disturbs
data transmission on the link.
Bypass one fixture at a time until normal operation
is regained: unplug the XLR in and out connectors
and connect them directly together. Have the fixture
serviced by a qualified technician.
XLR pin-out on fixtures does not match (pins
2 and 3 reversed).
Install a phase-reversing cable between the fixtures
or swap pins 2 and 3 in the fixture that behaves
erratically.
Effect wheel requires mechanical adjustment.
Disable effects feedback (page 15). Contact Martin
technician for service.
The transformer setting does not match local
voltage.
Disconnect fixture. Check transformer setting and
correct if necessary.
Mechanical train requires cleaning,
adjustment, or lubrication.
Contact Martin technician for service.
The ballast and transformer settings do not
match local AC voltage and frequency.
Disconnect fixture. Check ballast and transformer
settings and correct if necessary.
Lamp blown
Disconnect fixture and replace lamp.
Lamp not installed
Disconnect fixture and install lamp.
Lamp access safety switch open
Verify that lamp access plate is fully seated and
locked in place.
Lamp too hot to strike
Send a lamp off command. Allow the lamp to cool
for 5 - 10 minutes and try again.
Fixture is too hot.
Allow fixture to cool.
Clean air filters.
Reduce ambient room temperature.
The ballast and transformer settings do not
match local AC voltage and frequency.
Disconnect fixture. Check ballast and transformer
settings and correct if necessary.
Lamp cuts out intermittently.
Table 7: Troubleshooting
Troubleshooting
35
CIRCUIT
36
BOARD CONNECTIONS
MAC 2000 Profile II
SPECIFICATIONS
MAC 2000 PROFILE II
Note that versions with electronic ballast are denoted with an ‘E’.
PHYSICAL
Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 408 mm (16.0 in)
Width: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 mm (19.3 in)
Height: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 743 mm (29.3 in)
Weight - MAC 2000 Profile II E: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 kg (84 lbs)
Weight - MAC 2000 Profile II:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 kg (99 lbs)
S O U RC E
Lamp: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200 W short arc discharge
Base: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Double-ended SFc 10-4 with key
Approved models: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Osram HMI 1200 W/S Short-Arc
Control: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . automatic and remote, hot re-strike w/ electronic ballast
THERMAL
Maximum ambient temperature (Ta) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40° C (104° F)
Maximum surface temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140° C (284° F)
CONTROL
AND PROGRAMMING
Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USITT DMX-512 (1990)
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Opto-isolated RS-485
Control channels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 or 24
Data I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . locking 3-pin & 5-pin XLR, pin 1 shield, pin 2 cold (-), pin 3 hot (+)
ELECTRICAL
AC input: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 m trailing cable w/o cord cap
Operating ranges (electronic ballast):. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100-130/200-260 V, 50/60 Hz
Operating ranges (magnetic ballast): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200-260 V, 50/60 Hz
Main fuses (x 2 - when local AC supply is 200 - 250 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 A
Main fuses (x 2 - when local AC supply is 100 - 120 V) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T 20 A
Fuse F101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T 6.3 A
Fuse F102 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . T 10 A
Fuse F103 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T 3.15 A
Fuse F104 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .T 3.15 A
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electronic auto-ranging
MAXIMUM
POWER AND CURRENT
-
MAGNETIC BALLAST
208 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1520 W, 9.3 A
208 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1410 W, 7.5 A
230 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1470 W, 7.6 A
230 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1450 W, 7 A
250 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480 W, 7.4 A
Specifications MAC 2000 Profile II
37
MAXIMUM
POWER AND CURRENT
-
ELECTRONIC BALLAST
100 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1590 W, 19.8 A
100 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1560 W, 19.3 A
120 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1560 W, 16.8 A
120 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1540 W, 16.3 A
208 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1470 W, 10.5 A
208 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1470 W, 10.3 A
230 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480 W, 9.6 A
230 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1470 W, 9.4 A
250 V / 50 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480 W, 8.6 A
250 V / 60 Hz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1480 W, 8.5 A
DESIGN
STANDARDS
EU EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 50 081-1, EN 50 082-1
EU safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN 60598-1, EN 60598-2-17
Canadian safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .CSA C22.2 No. 166
US safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI/UL 1573
CONSTRUCTION
Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UV-resistant fiber-reinforced composite
Protection factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .IP 20
INSTALLATION
Mounting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 pairs of 1/4-turn locks, offset 45°
Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . any
ACCESSORIES
MP-2 Uploader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G-clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Half-coupler clamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Wife DMX Tester . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
O RD E R I N G
INFORMATION
MAC 2000 Profile II in 1-unit flight case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 MAC 2000 Profile IIs in a 2-unit flight case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MAC 2000 Profile II E in 1-unit flight case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 MAC 2000 Profile II Es in a 2-unit flight case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
White MAC 2000 Profile II in a 1-unit flight case (minimum order – 10 pieces) . . . . . . . . . . . . . . . . . . .
White MAC 2000 Profile II E in a 1-unit flight case (minimum order – 10 pieces) . . . . . . . . . . . . . . . . .
38
P/N 90758420
P/N 91602003
P/N 91602005
P/N 91611038
MAC 2000 Profile II
P/N 90205610
P/N 90205600
P/N 90205810
P/N 90205800
P/N 90205620
P/N 90205820