Zanussi | ZWF 3100 | User manual | Zanussi ZWF 3100 User manual

35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 1
LAVADORA
WASHING MACHINE
ZWF 380
ZWF 3100
35.292.955/1
MANUAL DE USO
USER MANUAL
E
GB
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 26
Dear customer,
Please read these operating instructions carefully
and pay particular attention to the safety notes
indicated in the first pages. We recommend that you
keep this instruction booklet for future reference and
pass it on to any future owners.
Transport damages
When unpacking the appliance, check that it is not
damaged. If in doubt, do not use it and contact the
Service Centre.
The symbols you will see on some paragraphs of this booklet have the following meaning:
The warning triangle and/or the key words (Warning!, Caution!) emphasize information that is particularly
important for your safety or correct functioning of the appliance.
The information marked with this symbol provides additional instructions and practical tips on the use of
the appliance.
Tips and information about economical and ecological use of the machine are marked with this symbol.
26
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 27
Contents
Disposal
28-29
Maintenance
29
Tips for environmental protection 29
Technical specifications
Installation
30
31-32
Unpacking
31
Hydraulic connection
31
Levelling
32
Electrical connection
32
Your new washing machine
33
Description of the appliance
33
Detergent dispenser drawer
Use
Control panel
Controls
Washing hints
34
34
34-36
37
Sorting the laundry
37
Temperatures
37
Before loading the laundry
37
Maximum loads
37
Laundry weights
37
Removing stains
37
Detergents and additives
38
Quantity of detergent to be used
International wash code symbols
38
39
Operating sequence
40-41
Washing programmes
42-44
Bodywork
45
Detergent dispenser drawer
45
Cleaning of the drainage area
45
Water inlet filter
46
Emergency emptying out
46
Frost precautions
46
Something not working?
33
27
45
47-49
ENGLISH
Warnings
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 28
Warnings
The following warnings are provided in the interests of overall safety. You must read them carefully before
installing or using the appliance.
Installation
• Leave the porthole door slightly ajar when the
appliance is not in use. This preserves the door
seal and prevents the formation of musty smells.
• All internal packing must be removed before using
the appliance. Serious damage may be caused to
the machine or adjacent furniture if the protective
transit devices are not removed or are not
completely removed. Refer to the relevant
paragraph in the instruction book.
• Always check that water has emptied out before
opening the door. If not, drain the water following
the instructions in the instruction book.
• Always unplug the appliance and shut the water
tap after use.
• Any electrical work required to install this appliance
must be carried out by a qualified electrician.
General safety
• Any plumbing work required to install this
appliance must be carried out by a qualified
plumber.
• After having installed the machine, check that it is
not standing on its electrical supply cable.
• Repairs to the machine must be carried out only by
qualified personnel. Repairs carried out by
inexperienced persons could cause serious
danger. Contact your local Service Centre.
• If the appliance is placed on a carpeted floor,
ensure that air can circulate freely between the feet
and the floor.
• Never pull the power supply cable to remove the
plug from the socket; always take hold of the plug
itself.
• The power supply cable only can be replaced by a
person of the Technical Service.
• During high temperature wash programmes the
door glass may get hot. Do not touch it!
Use
• This appliance is designed for domestic use. It
must not be used for purposes other than those for
which it was designed.
• Only wash fabrics which are designed to be
machine washed. Follow the instructions on each
garment label.
• Do not overload the appliance. Follow the
instructions in the instruction book.
• Make sure that all pockets are empty. Objects such
as coins, safety pins, pins and screws can cause
extensive damage.
• Do not machine wash garments saturated with
petroleum, methylated spirits, trichlorethylene, etc.
If such fluids have been used to remove stains
prior to washing, wait until they have completely
evaporated from the fabric before placing garments
in the appliance.
• Place small items such as socks, belts, etc. in a
cloth bag or pillowcase to prevent them getting
trapped between the drum and the tub.
• Use only the recommended quantities of fabric
softener. An excessive amount could damage the
laundry.
28
14/11/06
12:30
Página 29
Child safety
• Keep all detergents in a safe place out of children’s
reach.
• Children are often not aware of how dangerous
electrical appliances can be. When the machine is
working, children should be carefully supervised
and not be allowed to play with the appliance.
• Make sure that children or pets do not climb into
the drum.
• When the appliance is to be scrapped, cut off the
electrical supply cable and destroy the plug with
the remaining cable. Disable the door catch in
order to prevent children from becoming trapped
inside while playing.
• The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children - danger
of suffocation! Keep them out of children’s reach.
Disposal
Packaging materials
The materials marked with the symbol
recyclable.
are
>PE<=polyethylene
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by disposing of
them properly in appropriate collection containers.
Machine
The symbol
on the product or on its packaging indicates that this product may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.
Tips for environmental protection
To save water, energy and to help protect the
environment, we recommend that you follow these
tips:
• With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature.
• Normally soiled laundry may be washed without
prewashing in order to save detergent, water and
time (the environment is protected too!).
• Measure out detergent according to the water
hardness, the degree of soiling and the quantity of
laundry being washed.
• The machine works more economically if it is fully
loaded.
29
ENGLISH
35.292.955…ZWF380-3100.qxd
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 30
Installation instructions
It is dangerous to alter the specifications or attempt to modify this product in any way.
Care must be taken to ensure that the appliance does not stand on the electrical supply cable.
Any electrical work required to install this appliance should be carried out by a qualified electrician or
competent person.
Any plumbing work required to install this appliance should be carried out by a qualified plumber or
competent person.
The power supply cable only can be replaced by a person of our Service Force Centre.
Technical specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
60 cm
MAXIMUM RECOMMEND LOAD
Cotton, linen
Synthetics
Delicates
Woollens
5 kg
2 kg
2 kg
1 kg
SPIN SPEED
ZWF 380
ZWF 3100
800 rpm máx.
1000 rpm máx.
POWER SUPPLY VOLTAGE/FREQUENCY
TOTAL POWER ABSORBED
MINIMUM FUSE PROTECTION
230 V/50 Hz
2100 W
10 A
WATER PRESSURE
50 kPa
800 kPa
Minimum
Maximum
This appliance complies with the following EEC Directives:
73/23/EEC of 19/02/73 relating to low voltage
89/336/EEC of 03/05/89 relating to electromagnetic compatibility.
30
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 31
Transit security bars
Hydraulic connection
Before starting the machine up, the transport
security bars must be removed as follows:
You are advised to keep all the transport security
bars. In case the appliance has to be transported
again.
There should be a COLD WATER tap near the
washing machine with a screwing on connection
pipe of 3/4 gas for the water supply, a sink, a wash
basin or a drainage system in the wall.
Previously check if:
1. Unscrew and remove
the three rear screws
by means of a key.
— it is not a hot water tap.
— the running water is clean. If not, run off a
reasonable amount of water to flush out any
debris that may have collected in the pipes.
Have the permanent drainage system in the wall
checked by a plumber.
P0287
1. Carefully screw the
pipe to the tap taking
care not to damage the
screwdrive and fix the nut
well on to the end in
order to avoid leaking.
2. Lean the appliance
back on the rear and
fit one of the
polystyrene angles
between the appliance
and the floor.
Make sure the hoses
are not squashed.
P0018
1
2
3. Carefully remove the
plastic bags on the left
and the right, pulling
them to the centre of
the appliance
P0021
3. Place the discharging
hose in a washbasin or
sink with the aid of the
bent piece delivered
separately. The bent
piece has to be entered
into the tube’s mouth in
order to assure the
support. Aforesaid piece
allows the hose to be
fixed to the wall by means of an opening on the upper
part and that way the hose does not move and its
falling is avoided.
AL009
P0001
2. If necessary turn the
hose adequately by
unscrewing the nut at the
rear of the appliance.
Now tighten the nut anew
to avoid leaks. (Open the
tap and assure that it
does not leak and close it
again.)
P0002
4. Place the machine in an upright position and
remove the three plastic bolts.
5. Plug the 3 holes with the plastic plugs which you
can find in the envelope containing the instruction
booklet.
31
ENGLISH
Installation
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 32
IMPORTANT: The distance from the floor to the
highest part of the hose should be between 60 to
90 cm. (It is advised to be between 60 and 70 cm).
The hose must not be bent nor twisted to avoid
clogging. Should a prolongation of the discharging
hose be unavoidable this must never surpass 1.5 m
and must be of the same diameter as the original
hose.
Make sure the hoses are not too tense.
90 cm. Max.
60 cm. Min.
1,5 m. Max.
Electrical connections
Before plugging the appliance make sure that:
1º. the mains of your installation is the same as on
the rating plate of your appliance (the plate is
sticked to the rear of the appliance).
2º. The meter, the fuses, the wiring and the socket
outlet can support the max. power absorbed stated
on the rating plate.
3º. The socket base and the plug must fit in
adequately without any reducing interposition,
multiple outlets or adapters. If necessary replace
the socket outlet by an adequate one.
Levelling
Level the appliance by loosening or tightening the
feet. Once in the right position fix the feet by
pushing the nuts (A) (see graphic P0254) against
the base of the case. Accurate levelling will prevent
vibration, noise and displacement of the appliance
during operation.
The applicable rules for electrical security
require an adequate earthing. The plug of the
appliance is provided with such a device.
Make sure your socket outlet is provided with
an adequate earthing too.
Some vibration is inevitable, especially if placed on
a wooden floor. Wooden floors are particularly
susceptible to vibrations. If possible always place
the appliance on a solid floor.
The manufacturer declines any liability in case
of accidents or incidents should these safety
measures not be observed.
The power supply cable only can be replaced by
a person of our Service Force Centre.
P0254
32
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 33
Your new washing machine
This new machine meets all modern requirements for effective treatment of laundry with low water, energy and
detergent consumption.
ENGLISH
• The balance control device reduces the risk of instability in machine movement and it guarantees a quieter
operation.
Description of the appliance
1 Detergent dispenser drawer
2 Programme chart
3 Control panel
4 Door handle
5 Drainage area door
6 Adjustable feet
Detergent dispenser drawer
Prewash
Main wash
Fabric softener, starch
R0001 3D
33
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 34
Use
Control panel
1. Detergent dispenser drawer
RETARDADO” option or to change the selected
delay, proceed as follows:
1. Turn the dial programme selector to position “O”.
2. Start the normal process to select a programme
again.
• If you need to stop the machine to put in more
laundry (having selected “8H/4H INICIO
RETARDADO” option first), proceed as follows:
1. Depress INICIO / PAUSA button.
2. Wait two or three minutes before opening the
door to give the electric locking mechanism
time to release.
3. Place the laundry in the drum.
4. Press again the INICIO / PAUSA button.
Programme option buttons
Depending on the programme, different option
buttons can be combined.
When these buttons are pressed, the corresponding
lights come on. When they are pressed again, the
lights go off.
If an incompatible option with the selected
programme has been chosen, the corresponding
light flashes for about 2 seconds.
The option buttons: 8H/4H INICIO RETARDADO;
PRELAVADO; LAVADO RÁPIDO and
REDUCCION DE CENTRIFUGA must be selected
after the required programme has been chosen, by
turning the programme selector (see section 8) and
before starting the machine, by pressing INICIO /
PAUSA button.
The “8H/4H INICIO RETARDADO” option can't be
selected with programmes
(DRAIN) or
(SPIN).
2. “8H/4H INICIO RETARDADO”
button
3. PRELAVADO button
Adds a pre-wash phase at the start of the cycle with
water heating to 30° C.
In COTTON and SYNTHETIC cycles, performs a
short spin before passing to the washing phase.This
option cannot be selected for LANA and LAVADO A
MANO cycles.
This button allows the delay of starting of the
washing programme by 8 H and 4 H hours.
The delay which has been selected is indicated
when the corresponding light comes on.
To use this option proceed as follows:
1. Select the required programme by the
programme selector (see section 9).
2. Press the required option buttons.
3. Push “8H/4H INICIO RETARDADO” button, as
many times as necessary to get the required
delay until the corresponding light comes on.
4. Press INICIO / PAUSA button. The machine will
begin the countdown.
4. LAVADO RÁPIDO button
Using this option, you can get good washing results
in a short period of time, since with option, the
COTTON, SYNTHETICS, and DELICATES
programmes are modified in order to obtain short
washing times (recommended for small or lightlysoiled loads).
This modification consists of reducing the number of
rinse cycles (one less) and also increases the water
level used in the remaining two rinse cycles.
IMPORTANT!
• If you would want to cancel“8H/4H INICIO
34
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 35
5. INICIO / PAUSA button
7. Programme progress display
After selecting the required programme, by the
programme selector (see section 8), press this
button to start the machine; the corresponding
light stops flashing and will keep lighting until
the programme finishes.
To interrupt the running programme, depress
INICIO / PAUSA button: the corresponding
light starts to flash.
To restart the programme from the point at
which it was interrupted, press INICIO / PAUSA
button again.
The light LAVADO will iluminate during all the
programme, turning off when it has finished.
ENGLISH
The light FIN will illuminate to indicate that the
selected programme has finished.
6. REDUCCIÓN CENTRIFUGADO
button
This button allows the reduction of the final and the
intermediate spin speed or to select the
ANTIARRUGAS option.
The light FIN flashes in the event of operating
problems:
• 4 flashes: door open.
• 2 flashes: problem with water draining.
• 1 flash: problem with water supply.
For more information see paragraph "Something not
working?" at the end of this booklet.
Press this button so many times as it was necesary
until the relevant light turns on corresponding to the
wished option.
The speeds on the lights reference to cotton
programmes in both models (ZWF380 and
ZWF3100).
• For the model ZWF3100:
- The light 1000 r.p.m. correponds to 900 r.p.m. in
synthetics and wool programmes and in the
delicates programmes corresponds to 700 r.p.m.
- The lights 700 r.p.m. and 500 r.p.m. are common
for all programmes making reference to the same
speed.
• For the model ZWF380:
- The light 800 r.p.m. correponds to 700 r.p.m. in the
delicates programmes.
- The lights 700 r.p.m. and 500 r.p.m. are common
for all programmes making reference to the same
speed.
NOTE: In both models, by default, the light of spin
speed will turns on according to the selected
programme.
RINSE HOLD: by selecting this option, the water
of the last rinse is not drained, in order to prevent
the fabrics from wrinkling. When the programme has
finished, FIN light will illuminate.
35
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 36
8. Programme selector dial
The selector dial can be turned either clockwise or
counter-clockwise.
Use this selector dial to select the required
programme.
At the end of each programme the selector dial
must be turned to position “O”, to switch off the
machine.
ATTENTION!
If the programme selector dial is turned to another
position (programme) when the machine is working,
the lights of the programme progress display start to
flash. The machine will not perform the new selected
programme, but it will continue running on the same
cycle.
REMEMBER!
In the event a wrong programme has been selected
and the machine is already working, proceed as
follows:
1. Turn the programme selector dial to position “O”.
2. Select the new required programme.
• If the machine has not already gone through the
rinse cycle, when you decide to change the running
programme, in the new programme the water and
the detergent from the previous cycle will be reused, making it an energy-saving tool. On the
other hand, if it is already in the rinse phase;
detergent, bleach,… must be re-measured.
3. Press INICIO / PAUSA button, to start the new
cycle.
36
14/11/06
12:30
Página 37
Laundry weights
Washing hints
The following weights are indicative:
bathrobe
Sorting the laundry
napkin
Follow the wash code symbols on each garment
label and the manufacturer’s washing instructions.
Sort the laundry as follows:
whites, coloureds, synthetics, delicates, woollens.
Temperatures
90°
60°
for normally soiled white cottons and linen
(e.g. tea cloths, towels, tablecloths,
sheets...)
for normally soiled, colour fast garments
(e.g. shirts, night dresses, pyjamas....) in
linen, cotton or synthetic fibres and for
lightly soiled white cotton (e.g. underwear).
1200 g
100 g
quilt cover
700 g
sheet
500 g
pillow case
200 g
tablecloth
250 g
towelling towel
200 g
tea cloth
100 g
night dress
200 g
ladies’ briefs
100 g
man’s work shirt
600 g
man’s shirt
200 g
man’s pyjamas
500 g
(cold)for delicate items (e.g. net curtains), mixed
30°-40° laundry including synthetic fibres and
woollens.
blouse
100 g
men’s underpants
100 g
Before loading the laundry
Removing stains
Never wash whites and coloureds together. Whites
may lose their “whiteness” in the wash.
Stubborn stains may not be removed by just water
and detergent. It is therefore advisable to treat them
prior to washing.
New coloured items may run in the first wash; they
should therefore be washed separately the first time.
Blood: treat fresh stains with cold water. For dried
stains, soak overnight in water with a special
detergent then rub in the soap and water.
Make sure that no metal objects are left in the
laundry (e.g. hair clips, safety pins, pins).
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and dab the
stain; treat several times.
Button up pillowcases, close zip fasteners, hooks
and poppers. Tie any belts or long tapes.
Remove difficult stains before washing. Rub
particularly soiled areas with a special detergent or
detergent paste.
Dried grease stains: moisten with turpentine, lay
the garment on a soft surface and dab the stain with
the fingertips and a cotton cloth.
Treat curtains with special care. Remove hooks or tie
them up in a bag or net.
Rust: oxalic acid dissolved in hot water or a rust
removing product used cold. Be careful with rust
stains which are not recent since the cellulose
structure will already have been damaged and the
fabric tends to hole.
Maximum loads
Recommended loads are indicated in the
programme charts.
Mould stains: treat with bleach, rinse well (whites
and fast coloureds only).
General rules:
Grass: soap lightly and treat with bleach (whites and
fast coloureds only).
Cotton, linen: drum full but not too tightly packed;
Synthetics: drum no more than half full;
Glue: moisten with acetone (*), lay the garment on a
soft cloth and dab the stain.
Delicate fabrics and woollens: drum no more than
one third full.
Lipstick: moisten with acetone as above, then treat
stains with methylated spirits. Remove any residual
marks from white fabrics with bleach.
Washing a maximum load makes the most efficient
use of water and energy.
For heavily soiled laundry, reduce the load size.
Red wine: soak in water and detergent, rinse and
treat with acetic or citric acid, then rinse. Treat any
residual marks with bleach.
37
ENGLISH
35.292.955…ZWF380-3100.qxd
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 38
Quantity of detergent to be used
Ink: depending on the type of ink, moisten the fabric
first with acetone (*), then with acetic acid; treat any
residual marks on white fabrics with bleach and then
rinse thoroughly.
The type and quantity of detergent will depend on
the type of fabric, load size, degree of soiling and
hardness of the water used.
Tar stains: first treat with stain remover, methylated
spirits or benzine, then rub with detergent paste.
(*) do not use acetone on artificial silk.
Water hardness is classified in so-called “degrees” of
hardness. Information on hardness of the water in
your area can be obtained from the relevant water
supply company, or from your local authority.
Detergents and additives
Follow the product manufacturer’s instructions on
quantities to use.
Good washing results also depend on the choice of
detergent and use of the correct quantities to avoid
waste and protect the environment. Although
biodegradable, detergents contain substances
which, in large quantities, can upset the delicate
balance of nature.
Use less detergent if:
– you are washing a small load,
– the laundry is lightly soiled,
– large amounts of foam form during washing.
The choice of detergent will depend on the type of
fabric (delicates, woollens, cottons, etc.), the colour,
washing temperature and degree of soiling.
Degrees of water hardness
All commonly available washing machine detergents
may be used in this appliance:
Degrees
Level
– powder detergents for all types of fabric,
Characteristic
– powder detergents for delicate fabrics (60°C max)
and woollens,
– liquid detergents, preferably for low temperature
wash programmes (60°C max) for all types of
fabric, or special for woollens only.
The detergent and any additives must be placed in
the appropriate compartments of the dispenser
drawer before starting the wash programme.
If using concentrated powder or liquid detergents, a
programme without prewash must be selected.
The washing machine incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Pour liquid detergent into the dispenser drawer
compartment marked
just before starting the
programme.
Any fabric softener or starching additives must be
poured into the compartment marked
before
starting the wash programme.
Follow the product manufacturer’s recommendations
on quantities to use and do not exceed the «MAX»
mark in the detergent dispenser drawer.
38
1
soft
2
medium
3
hard
4
very hard
German
°dH
French
°T.H.
0- 7
0-15
8-14
16-25
15-21
26-37
more than more than
21
37
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 39
International wash code symbols
These symbols appear on fabric labels, in order to help you choose the best way to treat your laundry.
Max. wash
temperature
95°C
Max. wash
temperature
60°C
Max. wash
temperature
40°C
ENGLISH
Energetic wash
Max. wash
temperature
30°C
Hand wash
Do not
wash
at all
Delicate wash
Bleaching
Bleach in cold water
Do not bleach
Ironing
Hot iron
max 200°C
Warm iron
max 150°C
Lukewarm iron
max 110°C
Do not iron
Dry cleaning
Dry cleaning
in all solvents
Dry cleaning in
perchlorethylene,
petrol, pure alcohol,
R 111 & R 113
Dry cleaning
in petrol,
pure alcohol
and R 113
Do not
dry clean
high
temperature
low
temperature
Drying
Flat
On the line
On clothes
hanger
39
Tumble dry
Do not
tumble dry
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 40
Operating sequence
Before washing your first load of laundry, we recommend that you run a cotton cycle at 60° C, with the machine
empty, in order to remove any manufacturing residue from the drum and tub. Pour half of the normal amount of
detergent into the main wash compartment and start up the machine.
1. Place the laundry in the drum
4. Select the required programme
Open the door by pulling the handle outwards. Place
the laundry in the drum, one item at a time, shaking
them out as much as possible. Close the door.
Turn the programme selector to the required
programme.
2. Measure the detergent
5. Select the spin speed or
rinse hold option
Pull out the dispenser drawer until it stops.
Measure the required amount of detergent, pour it
into the main wash compartment
and into the
compartment marked
(if
PRE-WASH option
has been chosen).
6. Select the required option push
button/s
R0070
3. Measure the fabric softener
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
"MAX" mark in the drawer).
Close the drawer gently.
R0071
40
14/11/06
12:30
Página 41
7. OPTIONAL! Select, if required,
“8H/4H INICIO RETARDADO”
option button
10. Interrupting a programme
Depress INICIO / PAUSA button to interrupt a
running programme, the corresponding light will
begin flashing. Press this button again to re-start the
programme.
Push “8H/4H INICIO RETARDADO” button as many
times as necessary until the corresponding light to
the required delay (8 H, 4 H) comes on.
11. Opening the door after the
programme has started
Firstly, stop the machine by pressing
INICIO / PAUSA button.
After about two or three minutes the door can be
opened.
If the door does not open , this means that the
temperature of the water is too high, that the water
level exceed the lower limit of the door (which could
cause overflowing) or that the drum is spinning.
If the door cannot be opened but you need to open it,
switch the machine off by turning the selector dial to
“O”. After approximately two or three minutes the
door can be opened. (PAY ATTENTION TO THE
WATER LEVEL AND TEMPERATURE!)
8. Start the machine
Before starting the machine check that:
• the appliance is plugged in.
• the water supply tap is turned on.
• the drain hose is correctly and securely positioned.
• the door and the detergent dispenser drawer are
closed.
12. At the end of the programme
The machine stops automatically.
Release of the lock is indicated when FIN light
comes on.
Turn the programme selector dial to position “O” to
switch the machine off.
Remove the laundry from the drum and carefully
check that the drum is empty.
If you do not intend to put in another wash, turn off
the water tap. Leave the door open to prevent from
forming mildew and unpleasant smells.
To start the selected programme, push
INICIO / PAUSA button; the corresponding light will
stop flashing and will remain lit until the end of the
programme.
ATTENTION!
If the
RINSE HOLD option has been selected,
the last rinse water does not drain. To drain the
water, carry out the following steps:
If “8H/4H INICIO RETARDADO” option has been
chosen, the machine will begin the countdown.
1. Turn the programme selector dial to “O”.
9. Modification of a running
washing programme
2. Select
DRAIN or
SPIN programme.
3. Press INICIO / PAUSA button.
Once the programme has started, it only can be
modified by turning the programme selector dial to
“O” and afterwards the new programme can be
chosen.
The washing water remains in the tub, provided that
the machine does not reach the rinse phase, since,
in this case, the machine drains it automatically.
Start the new programme by pressing
INICIO / PAUSA button.
41
ENGLISH
35.292.955…ZWF380-3100.qxd
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 42
Programme table
Washing programmes for cotton and linen
Programme
selector
dial
position
Washing
programme
Description
Possible option
Load
For heavily soiled cotton items.
Wash at 90° C
3 rinses
Spin
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
5 kg
White cotton, for example
moderately soiled work
garments, sheets, household
linen, underwear, towels.
Wash at 60° C
3 rinses
Spin
Prelavado
Inicio retardado
Rinse hold (*)
5 kg
Fast coloured cotton or linen
Wash at 40° C
COLORES
fabrics, moderately soiled, shirts, 3 rinses
ALGODÓN RESISTENTES blouses, underwear.
Spin
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
5 kg
Non fast coloured cotton or linen Wash at 30° C
fabrics, moderately soiled, shirts, 3 rinses
Spin
blouses, underwear.
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
5 kg
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
5 kg
90
ALGODÓN
60E
BLANCOS
AHORRO
ENERGÍA
(**)
ALGODÓN
Stains and type of fabric
40
30
ALGODÓN
CUIDA LOS
COLORES
ALGODÓN
ALGODÓN
EN FRÍO
O
PARADA
For slightly soiled cotton fabrics.
To cancel the running wash
programme and to switch the
machine off.
Cold wash
3 rinses
Spin
—
(*) When this option is selected, the last rinse water does not drain to avoid wrinkling in the fabrics. To drain
the water select
SPIN or
DRAIN programme.
(**) In compliance with EC directive 92/75, the consumption figures indicated on the energy label refer to the
60° C wash programme for cotton (programme 60E) with a wash load of 5 Kg.
42
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 43
Programme table
Washing programmes for synthetics, mixed fabrics, delicates and wool
Programme
selector
dial
position
Stains and type of fabric
Description
Possible option
Load
PLANCHADO
FÁCIL
Special programme for synthetic
fabrics, which makes ironing
easier.
Wash at 40° C
4 rinses
Spin impulse
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
2 kg
Synthetic or mixed fabrics,
underwear, coloured garments,
perma-press shirts, blouses.
Wash at 30° C
3 rinses
Short spin
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
2 kg
SINTÉTICO
EN FRÍO
Slightly soiled delicate synthetic
fabrics.
Cold wash
3 rinses
Short spin
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
2 kg
DELICADOS
LAVADO A
MANO
Especially delicate fabrics.
Wash at 30° C
3 rinses
Short spin
Inicio retardado
Rinse hold (*)
2 kg
Delicate fabrics, such as
curtains.
Cold wash
3 rinses
Short spin
Prelavado
Inicio retardado
Rinse hold (*)
Lavado rápido
2 kg
DELICADOS
DELICADOS
EN FRÍO
Use this wash cycle to wash
Woolmark garments according to
the instructions on the garments
label and following the
instructions booklet provided by
the manufacturer of this machine
(M9604).
Cold wash or
wash at 30° C
(depending on
the selected
position)
3 rinses
Short spin
Inicio retardado
Rinse hold (*)
1 kg
40
SINTÉTICOS
ENGLISH
Washing
programme
CARGA MIXTA
30
SINTÉTICOS
SINTÉTICOS
30
-30
LANA
O
LANA
PARADA
To cancel the running wash
programme and to switch the
machine off.
—
(*) When this option is selected, the last rinse water does not drain to avoid wrinkling in the fabrics. To drain
the water select
SPIN or
DRAIN programme.
43
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 44
Programme table
Special washing programmes
Programme
selector
dial
position
Washing
programme
ACLARADOS
CENTRIFUGADO
DESCARGA
O
PARADA
Stains and type of fabric
Description
Possible option
Load
Inicio retardado
Rinse hold (*)
5 kg
With this programme it is
possible to rinse and spin
garments which have been
washed by hand.
The machine performs 3 rinses,
and it finishes with a short spin.
3 rinses
Short spin
This programme can be used to
perform a short spin: for
garments washed by hand, for
example: to
wring them out, before hanging
them up.
This programme can be used to
drain and spin, too, when
RINSE HOLD option has
been selected.
Short spin
5 kg
To drain the water from the last
rinse in programmes with
RINSE HOLD option
selected.
Water drain
5 kg
To cancel the running wash
programme and to switch the
machine off.
—
(*) When this option is selected, the last rinse water does not drain to avoid wrinkling in the fabrics. To drain
the water select
SPIN or
DRAIN programme.
44
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 45
1. Bodywork
3. Cleaning of the drainage area
Clean the outside of the machine with warm water
and a neutral, non-abrasive household detergent.
Rinse with clean water and dry with a soft cloth.
The drainage area must be cleaned if the pump has
been blocked with objects such as buttons, safety
pins, coins, etc. , or if lint has built up because
clothes that generate lint have been washed at high
temperatures.
Important: do not use methylated spirits, solvents or
similar products to clean the bodywork.
After a while, detergents and fabric softeners leave
deposits in the drawer.
•
•
•
•
•
Clean the drawer from time to time by rinsing it under
a running tap. To remove the drawer from the
machine, press the button in the rear left-hand
corner.
• Empty the bowl. Repeat the procedure until you
have completely emptied the washing machine.
2. Detergent dispenser drawer
Pull out the plug from the power socket.
If necessary, wait until the water has cooled down.
Open the drainage area door.
Place a bowl to collect the water.
Release the emergency emptying hose, place it in
the bowl and remove its cap, when the bowl is full
put the cap back on the emergency emptying hose.
To facilitate cleaning, the top part of the additive
compartments can be removed.
P1114
R0072
P1115
C0073
• To continue, unscrew the lid of the diaphragm by
turning it counter clockwise and pull it out.
Detergent can also accumulate inside the drawer
recess: clean it with an old toothbrush. Refit the
drawer after cleaning.
• Always keep a rag nearby to dry up spillage of
water when removing the cover.
• Remove the objects such as buttons, coins and the
lint that has been accumulated in the area of the
pump impeller by rotating it.
• Screw the lid of the diaphragm clockwise, be sure
is completely tighten.
• Replace the emergency emptying hose in its initial
position and close the drainage area door.
P1116
45
P1117
ENGLISH
Maintenance
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 46
4. The water inlet hose filter
6. Frost precautions
If your water is very hard or contains traces of lime
deposit, the water inlet filter may become clogged.
If the machine is installed in a place where the
temperature could drop below 0°C, proceed as
follows:
It is therefore a good idea to clean it from time to
time.
• disconnect the appliance;
Turn off the water tap. Unscrew the water inlet hose.
• close the water tap;
Clean the filter using a hard bristle brush.
• if necessary, wait until the water has cooled down;
Tighten up the inlet hose.
• open the drainage area door;
• place a bowl to collect the water that will flow out;
• release the emergency emptying hose, place it in
the bowl and remove its cap;
• when the water stops flowing out, put the cap back
on the emergency emptying hose, replace the
emergency emptying hose in its initial position and
close the drainage area door.
By doing this, any water remaining in the machine is
removed, avoiding the formation of ice and,
consequently, breakage of the affected parts.
When you use the machine again, make sure that
the ambient temperature is above 0°C.
5. Emergency emptying out
If the water is not discharged (outlet pump is
blocked, filter or drain hose are clogged), proceed as
follows to empty out the machine:
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the drainage area door;
• place a bowl to collect the water;
• release the emergency emptying hose, place it in
the bowl and remove its cap, when the bowl is full
put the cap back on the emergency emptying hose;
• empty the bowl, repeat the procedure until you
have completely emptied the washing machine;
• replace the emergency emptying hose in its initial
position and close the drainage area door.
46
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 47
Something not working?
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without
calling technical service. Before contacting your local Service Force Centre, please check the following possible
problems listed below.
During machine operation it is possible that FIN light flashes to indicate that something is not working correctly.
• 2 flashes = the water is not drained.
• 1 flash = there is no water filling.
Once the problem has been eliminated, press INICIO / PAUSA button to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Problems which can be resolved without a technician's help.
Problems
Possible cause
- The machine does not start up:
•
•
•
•
•
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no power in the socket.
The main fuse or the fuse in the plug has blown.
The programme selector dial is not correctly
positioned and INICIO / PAUSA button has not been
pressed.
- The machine does not fill:
•
•
•
•
The water tap is off.
The filter in the inlet hose is blocked.
The inlet hose may be squashed or kinked.
The door has not been closed.
- The machine fills then empties
immediately:
• The end of the drain hose is lower than the
machine.
• The end of the drain hose is submerged in water.
• There is no air circulation in the installation,
between the machine drain hose and the one in the
house.
- The machine does not drain and / or
does not spin:
• The drain hose may be squashed or kinked.
RINSE HOLDoption has been selected.
•
• The drain pump may be blocked.
• The drain hose extension is not correct. Follow the
instructions to connect it to the drain.
• The drainage system pipes are blocked.
• The laundry load is off balance: redistribute the
garments in the drum to allow the machine to spin.
- There is water on the floor:
• There is too much detergent or an inappropriate
detergent has been used (it makes too much foam).
• Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
• The drain hose may be damaged or is not securely
positioned to prevent leaks.
• The detergent dispenser drawer is clogged.
• The drainage system pipes are blocked.
47
ENGLISH
• 4 flashes = door open.
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 48
Problems
Possible cause
- Unsatisfactory washing results:
• Little detergent or an inappropriate one has been
used. An insufficient amount of detergent leaves the
laundry looking grey.
• Stubborn stains have not been treated prior to
washing.
• The correct wash programme has not been
selected.
• Too much laundry has been placed in the drum.
- The machine vibrates when spinning:
• The transit bolts and packaging have not been
removed.
• The machine is in contact with the wall or furniture.
• The machine is not level and stable (check
diagonally).
• The laundry is not well distributed in the drum.
• There may not be enough laundry in the drum.
- The door does not open::
• The programme is still running.
• The door lock has not released yet.
• Water in the tub: if there is water in the tub, the door
RINSE HOLD option
cannot be opened (
selected).
- Spinning starts late or the machine
does not spin:
• The electronic off balance detection device has
interrupted the spin because the laundry is not evenly
distributed in the drum. The laundry is redistributed by
reverse rotation of the drum. This may happen
several times before the off balance disappears and
normal spinning can resume. If, after 10 minutes, the
laundry is still not evenly distributed in the drum, the
machine will not spin. In this case, redistribute the
load manually and re-select the spin programme.
- The machine makes an unusual noise:
• The machine is fitted with a type of motor which
makes an unusual noise compared to other traditional
motors. This new motor ensures a smoother starting
and an even distribution of the laundry in the drum
when the machine is spinning. At the same time it
increases the appliance stability.
- No water is visible in the drum:
• Appliances using modern technology are energy
efficient. They use very little water without affecting
washing results.
48
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 49
ENGLISH
If you are unable to identify or solve the problem,
contact our service centre. Before telephoning, make
a note of the model, serial number and purchase
date of your machine: the Service Centre will require
this information.
49
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 50
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 51
35.292.955…ZWF380-3100.qxd
14/11/06
12:30
Página 52
EHPOESL/Z - 12/2004
Download PDF

advertising