INSTALLATION INSTRUCTIONS INSTRUCCIONES

721.80513
721.80602
721.80603
721.80604
721.80609
721.80822
721.80823
721.80824
721.80829
721.80832
721.80833
721.80834
721.80839
INSTALLATION
INSTRUCTIONS
INSTRUCCIONES
DEINSTALACION
Read and save these
installation instructions.
Lea y guarde estas
instrucciones de
instalaci6n
MicrowaveHood Combination
Combinaci6nMicroondasCampana
Part No. 3828W5U0463
Sears, Roebuck and Co., Hoffman Estates, IL. 60179 U.S.A
www.sears.com.
YOUR SAFETY
BEFORE
FIRST
YOU START
• Proper installation
is the installer's responsibility!
- Read the entire manual before you begin.
- The model number label is located on the oven front. See Figure 1.
- Mounting plate is located on back side of microwave oven. See Figure 2.
BE SURE TO READ THE FOLLOWING
SAFETY
INSTRUCTIONS:
Model and Serial
Number Plate
Cooking Guide
Mounting
Plate
Mounting
Figure 1
Plate
Figure 2
WARNING
FOR YOUR SAFETY:
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not handled
properly. The dimensions of the oven are as follows:
Height : 16-7/16 inches
Width • 29-15/16 inches
Depth • 15-3/8 inches
• AVOID
ELECTRICAL
SHOCK!
- Before you drill into the wall, note where electrical outlets are and where electrical wires might be
concealed behind the wall.
YOU COULD GET AN ELECTRIC SHOCK if you contact electrical wires with your drill bit.
- Locate and disconnect the power of any electrical circuits that could be affected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
• ELECTRICAL
RATING OF THIS OVEN : 120V, 60Hz.
- You need a 120V, 60Hz, AC only, 20A, fused electrical supply (located in the cabinet above the
microwave as close as possible to the microwave circuit) serving only the microwave.
YOUR SAFETY FIRST
• THIS APPLIANCE MUST BE GROUNDED!
- If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an escape
wire for the electric current. This appliance is equipped with a cord having a grounding wire with a
grounding plug.
PROPERLY POLARIZED AND
• Place the plug into a properly installed and grounded
outlet. See Figure 3.
• Do not use an extension cord.
• Keep the power cord dry and do not pinch or crush it.
GROUNDED OUTLET
* DO NOT, UNDER ANY CIRCUMSTANCES,
REMOVE
THE POWER SUPPLY CORD GROUNDING
PRONG!
This appliance MUST be grounded!
For best operation, plug this appliance into its
own electrical outlet to prevent flickering of lights,
blowing of fuse or tripping of circuit breaker.
Three-Pronged (Grounding) plug
Figure
3
01
WARNING
If you use the grounding
plug improperly,
you risk electric shock!
- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you do
not completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.
WARNING
Improper
grounding
could result in electric
SAVE THESE INSTRUCTIONS
shock or other personal
FOR THE LOCAL ELECTRICAL
INSPECTOR'S
• DO NOT EXPOSE YOURSELF TO EXCESSIVE MICROWAVE
injury.
USE.
ENERGY!
-
DO NOT try to operate the microwave oven with the door open.
DO NOT tamper with or defeat the safety interlocks.
DO NOT place objects between the microwave oven front face and the door.
DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
DO NOT operate the microwave oven if it is damaged.
The microwave oven door must close properly to operate safely.
DO NOT use the microwave oven:
• If the door is bent.
• If the hinges or latches are broken or loose.
• If the door seals, sealing surfaces or glass is broken.
- DO NOT attempt to adjust or repair the oven yourself!
It should be adjusted and repaired by a qualified technician who can check for microwave leakage after
repairing the oven.
WARNING
If you do not use the microwave
to excessive microwave energy.
61
oven as instructed,
you could be exposed
YOUR SAFETY
FIRST
• MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT.
- Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be
constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
- ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.
- DO NOT mount the microwave oven to an island or peninsula cabinet.
- BE SURE the upper cabinet and rear wall structures are able to support 150 Ibs., plus the weight of any
items you place inside the oven or upper cabinet.
- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.
WARNING
If you do not mount the oven as instructed,
property damage.
you risk personal
injury and/or
Grounded Outlet
(inside upper cabinet)
.....
Power Suf 3lyCord Hole
/
30" rain. cabinet opening width
>/
/
30" rain. clearance from bottom
of cabinet to cooking surface
or countertop before installation.
L..--
(Use templates included
with installation instructions)
I
Figure 4
CAUTION
• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL
(a blanket) over the countertop or cooktop to protect it. Do not use a plastic cover.
Failure to protect these surfaces could result inproperty damage.
PARTS, TOOLS, MATERIALS
THE FOLLOWING
PARTS ARE SUPPLIED
WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
Damper/duct connector
(for roof vented or wall vented installation)
One power cord clamp and
One dark-colored mounting screw
(to hold the power cord)
One power cord clamp bushing (for the cord hole in a metal upper cabinet)
Four 114"x 3" toggle bolts
(for drywall holes)
Four 1/4" x 2" lag screws
(for wall stud holes)
Two 1/4" x 3" bolts
(for securing to the upper cabinet)
Two tapping screws
(for attaching the damper duct connector)
Four spring toggle heads
(for the toggle bolts)
One upper cabinet template
One rear wall template
(3 pieces mounting plate only)
I
REAR
WALL
TEMPLATE
I
NOTE: You need to install at least one lag screw into a 2" x 4" stud and four anchor bolts into the wall,
and the mounting area must meet the 150 Ibs. weight requirement.
63
PAR TS, TO 0 L S, MATER IA LS
YOU WILL NEED THE FOLLOWING
INSTALLATION:
TOOLS AND MATERIALS
FOR THE
Carton or other heavy material for covering the counter top.
Clear Tape
(for taping the templates to the wall)
Stud Finder or Thin Nail
Saber Saw (for cutting vent holes for roof
or wall vending)
Keyhole Saw (for the power cord hole)
Electric drill
Phillips Screwdriver (for the screws)
3/8" and 3/4" wood drill bits
Pencil
1/2" an d 3/16"
drill bits
Flat Blade Screwdriver (for the bolts)
Plumb Line
Measuring Tape (metal preferred)
Duct Tape
Small Side Cutters or Tin Snips
Caulking gun
,.,,,,..,:._
._)
Gloves
* If you have brick or masonry walls, you need special hardware and tools.
* The ductwork you need for the installation is not included. All wall and roof caps must have a back-draft
damper.
6
STEP 1: PREPARE THE
ELECTRICAL CONNECTIONS
_, WARNING
AVOID ELECTRICAL
SHOCK!
A
THIS APPLIANCE
1. Locate the grounded electric outlet for this oven in the
cabinet above the oven, as shown in Figure 4 Detail.
MUST BE GROUNDED!
Upper
NOTE: The outlet should be on a circuit dedicated to the
microwave oven 120V, 60Hz., AC only, with a
20ampere fused electrical supply.
I
Cabinet
::
Grounded Outlet
IMPORTANT: If you do not have the proper wall outlet,
you MUST have one installed by a qualified
electrician.
o
T
(Inside Cabinet)
Power-Supply-Cord Hole
2. You will cut the power-supply-cord hole (shown in
Figure 4 Detail) later when you prepare the wall and
upper cabinet in Step 4.
Figure 4 Detail
NOTE: Do not use an extension cord.
Keep the power cord dry and do not pinch or crush it.
_, WARNING
Improper
grounding
could result in electric
• DO NOT, UNDER ANY CIRCUMSTANCES,
CORD GROUNDING
PRONG!
• This appliance
MUST be grounded!
_,
shock or other personal
REMOVE
THE POWER
injury.
SUPPLY
STEP 2:
PREPARE
THE VENTING S YS YTEM
NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork
fittings and length are shown in Figure 9, page 9.
WARNING
THIS OVEN MUST BE PROPERLY
- FIRE HAZARD
VENTED!
You may vent your oven in one of three ways:
Roof Venting
If your oven is located on an outside wall near the roof, as in Figure 6 (3-1/4" x 10" duct) and
Figure 8 (6" round duct.)
Wall Venting
If
your oven
is located
on an and
outside
wall8 on
first duct.)
floor of your house, as in
Figure
5 (3-1/4"
x 10" duct)
Figure
(6"the
round
Room
If yourthe
oven
located on
an inside
of your
house,
in Figure
NOTE: Venting
If you choose
rearisexhaust
method
(roof wall
or wall
venting),
beas
sure
there is7.enough clearance within
the wall for the exhaust duct.
Wall Venting
Roof Venting
cabinet
cabinet
[__
_,
Wall venting
3-1/4"x10"
duct
wall cap
duct
through-the-wall
.,
Roof venting
Figure 5
REMEMBER
AS YOU INSTALL
6
THE VENTING:
Room Venting
roof cap
cabinet
6" min.
diameter
round
* Do not install two elbows together.
wall cap
elbow
* Use duct tape to seal all joints in the duct
system.
* Use caulking to seal the exterior wall or
roof opening around the cap.
th rough-the-roof
Figure
* Keep the length of the ductwork and the
number of elbows to a minimum to
ventilate your oven efficiently.
See examples on page 9.
* Keep the size of the ductwork the same.
U
3-1/4" to round
duct transition
,/
3-1/4" to round
ductwork transition
OVE
Figure
7
Figure 8
STEP 2:
PREPARE
STANDARD
THE VENTING SYSTEM
FITTINGS
NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension
duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking.
DUCT LENGTH
The total length of the duct system, including straight duct, elbows, transitions, wall or roof caps must not
exceed the equivalent of 140 feet.
For best performance,
do not use more than three 90 degree elbows.
Below are the standard fittings and their equivalent length in feet.
61
3 1/4" x 10" to 6" = 5 ft.
3 1/4" x 10" 900elbow = 25 ft
3 1/4" x 10" roof cap = 24 ft
3
90°elbow = 10 ft
3-1/4" x 10" flat elbow
= lOft
45°elbow = 5 ft
3 1/4" x 10" wall cap
= 40 ft
Figure 9
To calculate the equivalent length of each duct piece used, see the examples below.
I
For 3-1/4" x 10" SYSTEMS
3-1/4"x10"
_
90" elbow _\
6ft. --_1
Examples
_[3wall cap
1,
2ft.
1 3"1/4"
X 10" 90 ° elbow
1 Wall Cap
8 feet straight
TOTAL
duct
LENGTH
For 6" ROUND
90° elbows
_----
SYSTEMS
6ft. ---_
[_/wall
cap
transi_
=
25 ft.
=
40 ft.
=
8ft.
=
73 ft.
1 transition
2 90 ° elbows
=
=
5 ft.
20 ft.
1 Wall Cap
8 feet straight
TOTAL LENGTH
=
=
=
40 ft.
8 ft.
73 ft.
STEP 3:
PREPARE
THE VENTING BL 0 WER
Your microwave oven is shipped with the blower assembled for room venting (recirculating).
the blower if you want wall vented or roof vented installation.
WARNING
ELECTRICAL
SHOCK
HAZARD!
UNPLUG
You need to adjust
A
UNIT BEFORE
WORKING
ON IT.
• DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower wiring could result
in electrical shock.
REMOVE
THE MOUNTING
A thick, protective
PLATE:
1. Remove any shipping materials and parts from inside
the microwave oven.
2. Cover the counter top or cooktop with a thick,
protective covering to protect it from damage and dirt.
See Figure 10.
NOTE: If you have a free-standing range, disconnect
it, move it onto a piece of cardboard or
hardboard and pull it away from the wall, so
that you can get closer to the upper cabinet
and back wall for easier measuring and
drilling.
ring
Figure
_
Remove mounting plate 2 screws from the mounting
plate as shown and discard them.
(See Figure 11 .)
3,
4,
The mounting plate will also be used to locate and
mark the mounting holes on the rear wall.
5,
Locate exhaust adaptor, grease filters and hardware
packet.
10
_
o
Mounting
plate screws
_____j
tm
Control panel side
At this point, remove any adhesive tape (if there is
any), on the exhaust adaptor, the grease filters and
the power supply cord.
6,
ROOM VENTED
'=8
McountingPlate
rews
Mounting
plate
INSTALLATION:
Go to STEP 4, PREPARE THE WALL AND UPPER
CABINET FOR INSTALLATION located on page 13.
--,=_
--
Control panel sid_
Figure
10
Mounting
plate
11
STEP 3:
PREPARE
WALL VENTED
THE VENTING BLOWER
INSTALLATION:
--
1. Remove blower unit mounting screw(s) and blower
plate screw(s). Remove the blower plate from cabinet.
See Figure 12.
back plate
blower unit
blower plate
mounting screw(s)
(option)
2. Carefully lift the blower unit out of the microwave
oven. Disconnect the blower wire from connector.
See Figure 13.
Knockouts "B"
J_
3. Use side cutters or tin snips to cut and remove
knockouts "B" from Back plate. Discard knockouts.
Be careful not to distort the plate. See Figure 14.
blower plate
blower unit
mounting screw(s)
(option)
Figure 12
4. Rotate the unit so that the exhaust ports face the rear
of the cabinet. See Figure 15. Before you insert
blower unit, blower wire must be like Figure 15.
5. Reassemble the blower wire into the connector.
6. Place blower unit back into cabinet. Check that the
connector
exhaust ports face towards the rear of the cabinet.
See Figure 16.
01
3:
7. Reattach the blower plate to the top of the cabinet as
it was originally assembled. Attach with blower unit
mounting screw(s) and then blower plate mounting
screw(s). See Figure 17.
blower wire
8. Go to STEP 4, PREPARE THE WALL AND UPPER
CABINET FOR INSTALLATION
located on page 13.
Figure 13
IBII
blower
unit
__Parts
"B'
exhaust
ports
Figure
Figure 15
14
_
exhaust
ports
Figure 16
lower plate
mounting
screw(s) (option)
blower unit
mounting screw(s) (option)
Figure 17
11
STEP 3:
PREPARE
ROOF VENTED
THE VENTING BL 0 WER
INSTALLATION:
_
1,
2,
blower plate
Remove blower unit mounting screw(s) and blower
plate screw(s). Remove the blower plate from cabinet.
See Figure 18.
Carefully lift the blower unit out of the microwave
oveR.
3. Rotate blower unit 90 ° so the exhaust ports face the
top of the cabinet. See Figure 19.
4. Place blower unit back into microwave oven.
5,
Use side cutters or tin snips to cut and remove
knockouts "A" from blower plate. Discard knockouts.
Be careful not to distort the plate. See Figure 20.
6,
Reattach blower plate to microwave oven. Attach with
the blower unit mounting screw(s) and then the blower
plate mounting screw(s). See Figure 21.
screw(s) (option)
_-blower _late
_[1/Ounting
"'-'_'%:_
blower unit
mounting screw(s) (option)
Figure 18
blower
unit
Figure
19
Knockouts "A"
blower plate
Figure 20
mounting
screw(s) (option)
,ow
blower unit
mounting screw(s) (optior
Figure 21
12
STEP 4: PREPARE THE WALL AND
UPPER CABINET FOR INSTALLATION
MEASURE AND TACK / TAPE UP THE
TEMPLATE
1. Using a plumb line and (metal) measuring tape, find
and mark the vertical center line ,_ on the back
wall, as in Figure 22.
O
2. Find and mark one or two points where the studs
are on the wall (Studs are normally 16 inches apart.)
and then measure and mark the stud locations. If
you cannot find any wall stud, consult a local
building contractor.
O
CAUTION A
DO NOT ATTEMPT TO INSTALL THE
MICROWAVE OVEN IF YOU CANNOT FIND A
WALL STUD.
m
3. Line up the plumb line on the wall with the center
line on the mounting plate.
NOTE: Be sure the minimum width is 30 inches and
the distance from the top of the mounting
plate to the range or counter top is at least
30 inches. See Figure 4 on page 4.
Figure 22
4. Center mounting plate in opening by lining up the
plumb line on wall with centerline on mounting plate.
Make sure the minimum width is 30 inches and that
the top of the mounting plate is located a minimum
of 30 inches above the cooking surface.
See Figure 23.
NOTE: If the front edge of the cabinet is lower than
the back edge, adjust the mounting plate to
be level with the cabinet front.
5. Measure the bottom of the upper cabinet frame.
Trim the edges "A", "B" and "C" on the upper
cabinet template so that the template will fit on the
bottom of the upper cabinet. If upper cabinet has a
recessed frame, trim template so that it fits inside
the recessed area. Align the centerline of the upper
cabinet template with the centerline of the mounting
plate; then securely tape or tack the upper cabinet
template in place. See Figure 23.
(1-piece Mounting Plate)
Upper Cabinet
o
_
Mounting
Template
jt
oo
c>
Plate
(3-piece Mounting Plate)
Figure 23
13
STEP 4: PREPARE THE WALL AND
UPPER CABINET FOR INSTALLATION
DRILL THE HOLES IN THE WALL AND UPPER CABINET.
WARNING
BE VERY CAREFUL
WHEN DRILLING
HOLES
INTO THE WALL.
Electrical wires could be concealed behind the wall covering and if the drill hits them you
could get an electric shock.
1. Find the points on the mounting plate labeled "A", "B", "C" and "D". Drill a 3/16" diameter hole at any of
these points that are in front of a wall stud. Drill a 3/4" diameter hole at any of these points that are over
drywall.
2.
Drill a 3/8" hole at points "J" and "K" on the upper cabinet template.
NOTE: If the bottom of the upper cabinet is recessed 3/4" or more, you will need 2"x2" filler blocks (not
included) to provide additional support for the bolts. See Figure 24.
• Mark the center of each filler block and drill a 3/8" diameter hole at the mark.
• Align filler blocks over the two openings in the top of the microwave oven cabinet and attach to cabinet with
masking tape. See Figure 25.
3. Cut or drill a 2" diameter hole at the area marked "M", "power supply cord hole" on the upper cabinet template.
If the upper cabinet is metal, you will need to cover the edge of the hole with the power supply cord bushing
(supplied) to prevent damage to the cord from the rough metal edge.
WARNING
A
cabinet front
filler block
YOU MUST COVER THE EDGE OF
THE POWER SUPPLY CORD HOLE
IN A METAL CABINET WITH THE
POWER SUPPLY CORD BUSHING.
FAILURE TO DO SO COULD
RESULT IN DAMAGE TO THE CORD
AND ELECTRIC
SHOCK.
Figure 24
4. Cut out the venting areas (with the saber saw):
• Roof Venting: cut out the shaded area marked "L"
on the upper cabinet template.
• Wall or Room Venting (Recirculating): go to STEP
5, INSTALL THE MOUNTING PLATE, located on
page 15.
5. Use caulking compound to seal the exterior wall or
roof opening around the wall cap or roof cap.
Figure 25
14
cabinet
bottom shelf
STEP 5: INSTALL THE MOUNTING
PL ATE TO THE WA L L
THE OVEN MUST BE CONNECTED
TO AT LEAST ONE WALL STUD.
3/16 Hole on Studs
5/8 Hole on Drywall Only
I
Minimum 66" I
From the Floor
I
r---
ILIL
1. Draw a vertical line on the wall at the center of the
30" wide space.
, _ .
Use the mounting plate as the template for the
rear wall. Place the mounting plate on the wall,
making sure that the tabs are against the bottom
of the cabinet. Line up the notch and center line
on the mounting plate to the center line on the
wall.
ntedC
, ,_--_
/ '!,"-I---..../
.....""
m
;
,
2. While holding the mounting plate with one hand,
draw circles on the wall at holes "A", "B", "C"
and "D". Four holes must be used for mounting. If
the holes are not used, the installation will not be
secure. Installer must use these holes for proper
installation. Use toggle bolts through these holes
unless one of them lines up with a stud. Use a lag
screw for studs. See Figure 26.
_r
Draw Lines
on Studs
_
Draw
Center Line :
Mounting
Plate
/
J
61
I
I
L
._
Su
NOTE: Draw a fifth circle inside area "E", through
one of the holes to match the location of a
stud.
Ul
J
Su
(1-piece Mounting Plate)
3/16 Hole on Studs
Minimum 66" ]
5/8 Hole on Drywall Only
From
theFIoor/
For wall vented: The oven requires a rear wall
cutout opening for the rear wall duct and the
exhaust adaptor must be attached to the mounting
plate. See the next page on how to prepare the rear
wall cutout opening and the exhaust
adaptor/mounting plate for wall vented.
I
I, _-
I
III1__
4'/ILvented°'!l
oo,
!
o?.........
3. Drill holes through the circles. If there is a stud,
drill a 3/16" hole for lag screws. Two or preferably
four lag screws at holes "A" and "C", or "B" and
"D" must be used to secure mounting plate to
wall. If there is no stud, drill a 3/4" hole for toggle
bolts. Make sure to use at least 1 lag screw at
holes of area "E" in a stud, and 4 toggle bolts at
holes "A", "B", "C" and "D" in the drywall or the
plaster.
,, L
i
Draw Lines i '_
on Studs
II
/
'
_
[] _/'
/
IIII '
Draw _
i
Mounting
II11/[]Center
Line.
4. Attach the plate to the wall. To use spring toggle
head bolts: Remove the toggle wings from the
bolts. Insert the bolts into the mounting plate and
replace the spring toggle heads to 3/4" past the
bolt ends. Insert the spring toggle heads into the
holes in the wall to mount the bracket. You may
pull forward on the bracket to help in tightening
the toggle bolts. Tighten all bolts. See Figure 27.
_
Center LineL_ ]
Plate
J,
"r_
', III
_ Ioli
Supp[rt
TabL--%--Isupp[rt
Tab
(3-pieceMounting Plate)
Figure 26
I
Mounting
Plate'-..d....I:: iI
i_
Space More Than Wall Thickness
Toggle Wings
, ,_ ToggleBolt III '!LI
l_ll_ii:i__
__
BOltEnd
Figure 27
15
STEP 5: INSTALL THE MOUNTING
PL ATE TO THE WA L L
TO PREPARE THE REAR WALL
CUTOUT OPENING AND EXHAUST
ADAPTOR/MOUNTING
PLATE FOR
WALL VENTING AND ROOF
VENTING:
• Make the box cutout for the rear wall duct.
- 1 piece mounting plate:
Using a pencil, put dots through slots F and G,
and through holes H and I. Remove the mounting
plate and draw lines extending through the points.
This will give the location and size of the box
cutout for the rear wall duct. (Figure 28)
- 3 pieces mounting plate:
Use the wall template to determine the location
and size of the box cutout for the rear wall duct.
• Attach the exhaust adaptor to the rear mounting
plate by sliding it into the guides at the top center
of the plate on the wall side. Push in securely until
it is past the top locking tabs and in the lower
locking tabs. Take care to assure the damper
hinge is installed so that it is at the top and that the
damper swings freely.
• Carefully guide the exhaust adaptor, now attached
to the mounting plate, into the house duct, before
using the screws to attach the plate to the wall.
This will assure proper alignment for installation.
See Figure 29.
• Return to step 5, item 3 (page 15) to continue.
After completing the installation of the mounting
plate, again check the rear damper for free
movement to assure it will operate properly.
Figure 28
Damper
(hinge side up)
Exhaust Adaptor
-Mounting Plate
(1 piece
mounting plate)
Slide exhaust
adaptor into
guides on
rear panel,
- Back Plate
I
(3 pieces
mounting plate)
Locking
Tabs
Figure 29
16
Guides
STEP 6:
ATTACH THE 0 VEN TO THE WALL
_, WARNING
_,
You will need two people to lift this
microwave. Failure to use more
than one person could result in
personal injury.
I
I _'--'_-...
_X,L_
"l.._-l_powe
r co rd
1. Carefully lift microwave oven and hang it on support
tabs (See Figure 26) at the bottom of the mounting
plate. Reaching through upper cabinet, thread
power supply cord through the power supply cord
hole in the bottom of the upper cabinet.
See Figure 30.
2. Rotate the microwave oven upward so the top of
oven is against the bottom of the upper cabinet or
cabinet frame.
ffl
Figure
30
Figure
31
_,_
3. Then insert a bolt down through each hole in the
upper cabinet bottom. See Figure 31.
Tighten the bolts until the gap between the upper
cabinet and microwave oven is closed.
4. If wall vented or room vented installation is used, go
to No. 7 on the next page.
17
STEP 6:
ATTACH THE OVEN TO THE WALL
5. Roof vented installation: See Figure 32.
Install ductwork through the vent opening in the
upper cabinet. Complete the venting system through
the roof according to the method needed. See
"PREPARE THE VENTING SYSTEM," STEP 2 on
the page 8. Use caulking to seal exterior roof
opening around the exhaust cap. See Figure 6 on
page 8.
_
_1
damper
I
I
6. Use power supply cord clamp to bundle the power
supply cord. Install the power supply cord clamp,
using a screw as shown in Figure 33, to inside of
the cabinet.
7. To install the grease filter: Slide it into the slide slot,
then push up and toward oven center to lock.
See Figure 34.
Figure 32
I I-:-1
t_\\lJlI \power
J
I
I_JTI
..................................
__1
I cord
clamp
I1©1
8. Plug in the power supply cord.
9. Read your Owner's Manual, then check the
operation of your microwave oven.
Figure
33
Figure 34
18
r
_,W I supply
MEMO
19