Avigilon | H3-BO1-IR | Installation guide | Avigilon H3-BO1-IR Installation guide

Installation Guide
Avigilon High Definition H.264 IP Camera
Models:
1.0W-H3-BO1-IR, 1.0W-H3-BO2-IR, 2.0W-H3-BO1-IR, 2.0W-H3-BO2-IR,
3.0W-H3-BO1-IR, 3.0W-H3-BO2-IR, 5.0-H3-BO1-IR and 5.0-H3-BO2-IR
920-0087A-Rev1
This manual provides installation and operation information and
precautions for the use of this camera. Incorrect installation could
cause an unexpected fault. Before installing this equipment read this
manual carefully. Please provide this manual to the owner of the
equipment for future use.
The Warning symbol indicates the presence of dangerous
voltage within and outside the product enclosure that may
constitute a risk of electric shock, serious injury or death to
persons if proper precautions are not followed.
The Caution symbol alerts the user to the presence of
hazards that may cause minor or moderate injury to
persons, damage to property or damage to the product
itself if proper precautions are not followed.
Warning — Failure to observe the following instructions may
result in severe injury or death.
•
•
•
•
Installation must be performed by qualified personnel only,
and must conform to all local codes.
This product is intended to be supplied by a UL Listed
Power Unit marked “Class 2” or “LPS” or “Limited Power
Source” with output rated 12 VDC or 24 VAC, 22 W min. or
Power over Ethernet (PoE), rated 48 VDC, 22 W min.
Any external power supply connected to this product may
only be connected to another Avigilon product of the same
model series. External power connections must be
properly insulated.
Do not connect directly to mains power for any reason.
i
English
Important Safety Information
English
Caution — Failure to observe the following instructions may
result in injury or damage to the camera.
•
•
•
•
•
•
•
ii
Do not install near any heat sources such as radiators, heat
registers, stoves, or other sources of heat.
Do not subject the cables to excessive stress, heavy loads
or pinching.
Do not open or disassemble the device. There are no user
serviceable parts.
Refer all servicing to qualified personnel.
Servicing may be required when the device has been
damaged (such as from a liquid spill or fallen objects), has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not use strong or abrasive detergents when cleaning
the device body.
Use only accessories recommended by Avigilon.
Use of controls or adjustments or performance of
procedures other than those specified in this document
may result in hazardous radiation exposure.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for
a Class B computing device pursuant to Subpart B of Part 15 of FCC
rules, which are designed to provide reasonable protection against
such interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to cause
interference, in which case the user at his/her own expense will be
required to take whatever measures may be required to correct the
interference.
Changes or modifications made to this equipment not expressly
approved by Avigilon Corporation or parties authorized by Avigilon
Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose
of it according to your local environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat
above 100 °C (212 °F), or incinerate.
iii
English
Regulatory Notices
European Union:
English
This symbol means that according to local laws and
regulations your product should be disposed of separately
from household waste. When this product reaches its end of
life, take it to a collection point designated by local
authorities. Some collection points accept products for free.
The separate collection and recycling of your product at the
time of disposal will help conserve natural resources and
ensure that it is recycled in a manner that protects human
health and the environment.
iv
English
Other Notices
Compilation and Publication Notice
This manual has been compiled and published covering the latest
product descriptions and specifications. The contents of this manual
and the specifications of this product are subject to change without
notice. Avigilon reserves the right to make changes without notice in
the specifications and materials contained herein and shall not be
responsible for any damages (including consequential) caused by
reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
Intellectual Property Notice
No license is granted by implication or otherwise under any industrial
design, industrial design rights, patent, patent rights, or copyrights of
Avigilon Corporation or its licensors. Trademarks and registered
trademarks are the property of their respective owners.
v
English
vi
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Side View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Camera Package Contents . . . . . . . . . . . . . . . . . . . . . . 4
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Adding the Mounting Holes . . . . . . . . . . . . . . . 4
Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . 4
Mounting the Camera . . . . . . . . . . . . . . . . . . . . 5
Assigning an IP Address . . . . . . . . . . . . . . . . . . 6
Accessing the Live Video Stream . . . . . . . . . . 6
Aiming the Camera . . . . . . . . . . . . . . . . . . . . . . . 7
Focusing the Camera . . . . . . . . . . . . . . . . . . . . . 7
(Optional) Configuring Onboard Storage . . . . 8
For More Information . . . . . . . . . . . . . . . . . . . . . 8
Connecting to External Devices . . . . . . . . . . . . . . 9
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Removing the Sun Shroud . . . . . . . . . . . . . . . . . . 11
Reinstalling the Sun Shroud . . . . . . . . . . . . . . . . . . . . . 11
Reset to Factory Default Settings . . . . . . . . . . . .12
Setting the IP Address Through the
ARP/Ping Method . . . . . . . . . . . . . . . . . . . . . . . . . .13
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Limited Warranty & Technical Support . . . . . . . .15
English
Table of Contents
English
English
Overview
Front View
Sun Shroud
IR Illuminator
Feature
Description
Sun Shroud
An adjustable cover to help protect the
lens against glare from the sun.
IR Illuminator
Provides scene illumination in the IR
spectrum.
1
Bottom View
English
Connection Status LED
Configuration
Ethernet Port
Feature
Link LED
Configuration Panel
Cable Entry Notch
SD Card Slot
Serial Number Tag
Description
Configuration Panel
Quick access port for configuring the camera
during installation. To access the
Configuration Panel, remove the plug with
the supplied opening tool.
Configuration Ethernet A secondary Ethernet port for configuring
Port
the camera. Does not accept PoE.
Link LED
Indicates if there is an active connection in
the Ethernet port. The light is On when there
is an active network connection.
Connection Status LED Provides information about device operation.
See LED indicators for more information.
SD Card Slot
Cable Entry Notch
Serial Number Tag
2
Accepts an SD card for onboard storage.
See (Optional) Configuring Onboard Storage
for more information.
An entry notch for network, power and I/O
cables.
Product serial number and part number
label.
Sun Shroud Mount
Mount Arm
Mounting Bracket
Adjustment Screws
Feature
Description
Sun Shroud Mount Mounting bracket for the sun shroud.
Mount Arm
Adjustable mount arm for positioning the
camera.
Mounting Bracket
Allows the camera to be flush mounted or
surface mounted.
Adjustment
Screws
Provides a locking mechanism for the mount
arm.
3
English
Side View
English
Installation
Camera Package Contents
Ensure the package contains the following:
•
•
•
•
•
Avigilon High Definition IP Bullet Camera
T20 TORX tamper resistant key
4 screws and anchors for solid walls
Drill template sticker
Configuration Panel opening tool
Installation Steps
Complete the following procedures to install the camera.
1.
2.
3.
4.
5.
6.
7.
8.
Adding the Mounting Holes on page 4
Connecting Cables on page 4
Mounting the Camera on page 5
Assigning an IP Address on page 6
Accessing the Live Video Stream on page 6
Aiming the Camera on page 7
Focusing the Camera on page 7
(Optional) Configuring Onboard Storage on page 8
Adding the Mounting Holes
1.
Use the drill template to drill four mounting holes in the
ceiling or wall.
•
Only drill the optional center hole if you are flush
mounting the camera. Once the center cable hole
has been drilled, pull the required cables through.
Connecting Cables
To connect the cables required for proper operation, complete the
following:
4
2.
If there are external input or output devices that need to be
connected to the camera (for example: door contacts,
relays, speakers, etc), connect the devices to the camera’s
I/O connector cable.
For more information, see Connecting to External Devices.
Connect power using one of the following methods:
•
Power over Ethernet (PoE) Class 3 — If PoE is
available, the camera is automatically detected
when the network cable is connected.
•
3.
4.
External Power — Connect the camera to an
external 12 VDC or 24 VAC power source through
the auxiliary power cables.
Connect the Ethernet Port (RJ-45 connector) to a network
using an Ethernet network cable. The Link LED in the
Configuration Panel under the camera will turn On once a
network link has been established.
Check that the Connection Status LED in the Configuration
Panel displays the correct state.
For more information, see LED Indicators.
Mounting the Camera
After the cable connections have been made, mount and secure the
camera.
1.
Tuck the extra lengths of cables away:
•
If you are flush mounting the camera, push the extra
lengths of cable through the cable hole in the wall
or ceiling.
•
2.
If you are surface mounting the camera, remove the
mounting gasket and tuck the connected cables to
one side through the cable entry notch in the
mounting bracket. When installed outdoors, the
cable entry notch must face downwards.
Ensure the mounting gasket is used when flush mounting
the camera.
5
English
1.
English
The gasket is required to maintain the mounting bracket’s
water resistance when installed outdoors.
3.
Drive the provided screws into the mounting holes and
tighten the camera bracket to the mounting surface.
Assigning an IP Address
The camera automatically obtains an IP address by default. Once
connected to a network, it attempts to locate and obtain an IP address
from a DHCP server. If this fails, Zero Configuration Networking
(Zeroconf) is used to choose an IP address. When the IP address is set
using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
The IP address settings can be changed using one of the following
methods:
•
•
Avigilon Camera Installation Tool software application.
Camera's web browser interface:
http://<camera IP address>/
•
ARP/Ping method. For more information, see Setting the IP
Address through the ARP/Ping Method.
•
Network Video Management software application (for
example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:
•
•
Avigilon Camera Installation Tool software application.
Camera's web browser interface:
http://<camera IP address>/.
•
Network Video Management software application (for
example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
6
1.
(Optional) To help you aim the camera, you can connect an
Ethernet cable to the secondary Ethernet port in the
Configuration Panel.
Be aware that while the Configuration Ethernet Port is in
use, the primary Ethernet port at the back of the camera
will only be used for PoE.
Important: While the Configuration Ethernet Port is in use, the camera
will only stream video and accept commands from the Configuration
Ethernet Port. Also, the Indicator LEDs will only show the connection
status for this Ethernet port.
2.
To aim the camera, loosen the adjustment screws on the
camera mount arm.
Only loosen the screws that can be rotated by the supplied
tamper resistant key.
3.
Rotate and move the camera and mount arm as required.
Review the camera’s live video stream to help aim the
camera correctly.
Slide the sun shroud forward or back to protect the camera
against glare from the sun. In outdoor installations, the sun
shroud should be set as far forward as possible without
intruding on the video image.
•
To move the sun shroud, hold down the black tabs
on either side of the camera then slide the sun
shroud forward or back.
4.
5.
6.
Once satisfied, tighten the adjustment screws on the
mount arm to secure the camera’s position.
In the Avigilon Camera Installation Tool or camera web
browser interface, adjust the camera’s Image and Display
settings to achieve the desired zoom position.
Focusing the Camera
•
In the Avigilon Camera Installation Tool or camera web
browser interface, use the camera’s Image and Display
settings to focus the camera lens.
7
English
Aiming the Camera
English
a.
Click the Auto Focus button to focus the lens.
b.
If the desired focus was not achieved, use the focus
near and far buttons to adjust the focus.
(Optional) Configuring Onboard Storage
To use the camera’s onboard storage feature, you must insert an SD
card into the SD card slot. Avigilon offers a line of SD cards that have
been fully tested with this camera to ensure optimal SD card
performance. For ordering information, please refer to the Avigilon
price list.
It is recommended that the SD card have a capacity of 8GB or more,
and a write speed of class 6 or better. If the SD card does not meet the
recommended capacity or write speed, the performance of the
onboard storage may suffer and result in the loss of frames or footage.
1.
Insert an SD card into the camera.
Caution — Do not force the SD card into the camera or you
may damage the card and the camera. The SD card can only
be inserted in the direction shown on the camera.
2.
Access the camera’s web interface to enable the onboard
storage feature.
For more information, see the Avigilon High Definition
H.264 Camera Web Interface User Guide.
For More Information
Additional information about setting up and using the device is
available in the following guides:
•
•
•
Avigilon Camera Installation Tool User Guide
Avigilon Control Center Client User Guide
Avigilon High Definition H.264 Web Interface User Guide
The manuals are available on the Avigilon website: http://avigilon.com/
support-and-downloads.
8
External devices are connected to the camera through the I/O cable.
Refer to the following table for the connections.
NOTE: The camera can be connected to an external microphone and
speaker through the I/O connector.
Table:External I/O Connections
Wire Color
Yellow
Brown
Green
Grey
Pink
Red
Purple
Description
Audio ground return
Audio input
Audio output
Relay ground return
Relay output 1
Relay input 1
+12 V output for relay drive
NOTE: The 12 V connection can be used to energize a relay coil with
up to 50 mA. If more than 50 mA is required, an external power
supply up to 25 VDC at 120 mA can be used.
12 V
GND
MAX 50 mA
GND
GND
PINK
RED
GREY
PURPLE
RELAY
Max 50 mA
SWITCH
3.3 V
IN
OUT
MAX 120 mA
GND
Figure: External I/O schematics and example application.
9
English
Connecting to External Devices
English
LED Indicators
Once the camera is connected to the network, the Connection Status
LED will display the camera’s progress in connecting to the Network
Video Management software.
The following table describes what the LEDs indicate:
Table:LED Indicators
Connection
State
Connection
Status LED
Description
Obtaining IP One short
Address
flash every
second
Attempting to obtain an IP address.
Discoverable Two short
flashes every
second
Obtained an IP address but is not
connected to the Network Video
Management software.
Upgrading
Firmware
Two short
Updating the firmware.
flashes and
one long flash
every second
Connected
On
10
Connected to the Network Video
Management software.
English
Removing the Sun Shroud
The sun shroud is not required when the camera is installed indoors.
1.
As you press down on the center of the sun shroud, pull up
the corners of the shroud from one side of the camera.
Avoid the black tab on the sun shroud mount.
The sun shroud should lift off the camera.
2.
Use a 2 mm or 5/64” hex driver to unscrew and remove the
sun shroud mount from the camera.
Reinstalling the Sun Shroud
1.
2.
3.
Use a 2 mm or 5/64” hex driver to screw on the sun shroud
mount.
Align one side of the sun shroud on to the mount.
Press down on the center of the sun shroud until it clicks
into place.
11
English
Reset to Factory Default
Settings
If the camera no longer functions as expected, you can choose to
restore the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Firmware Revert Button
Figure: The firmware revert button in the Configuration Panel.
1.
2.
3.
4.
Ensure the camera is powered on.
Unscrew the Configuration Panel Plug at the bottom of the
camera with the supplied opening tool.
Using a straightened paperclip or similar tool, gently press
and hold the firmware revert button for 2 seconds.
Screw the Configuration Panel Plug back into place.
Caution — Do not apply excessive force. Inserting the tool
too far will damage the device.
12
Complete the following steps to configure the camera to use a specific
IP address:
1.
2.
Locate and copy down the MAC Address (MAC) listed on
the Serial Number Tag for reference.
Open a Command Prompt window and enter the following
commands:
a.
arp -s <New Camera IP Address> <Camera
MAC Address>
For example: arp -s 192.168.1.10 00-1885-12-45-78
b.
3.
4.
ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
Reboot the camera.
Close the Command Prompt window when you see the
following message:
Reply from <New Camera IP Address>: ...
13
English
Setting the IP Address Through
the ARP/Ping Method
English
Specifications
H3-BO1-IR
H3-BO2-IR
Camera
Audio Input/Output
Lens
Onboard Storage
Line level input and output
3-9 mm, F1.2, P-Iris, remote focus
9-22 mm, F1.6, P-Iris, remote focus
and zoom
and zoom
SD/SDHC/SDXC slot – minimum class 4; class 6 or better recommended
Network
Network
Cabling Type
Connector
API
Security
Protocols
Streaming Protocols
100Base-TX
CAT5
RJ-45
ONVIF compliance version 1.02, 2.00, Profile S (www.onvif.org)
Password protection, HTTPS encryption, digest authentication, WS
authentication, user access log
IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP, IGMP,
ICMP, DHCP, Zeroconf, ARP
RTP/UDP, RTP/UDP multicast, RTP/RTSP/TCP, RTP/RTSP/HTTP/TCP,
RTP/RTSP/HTTPS/TCP, HTTP
Mechanical
Dimensions LxWxH
Weight
Body
Housing
Finish
Adjustment Range
Cable Length
241.7 mm x 94.9 mm x 70 mm (9.5” x 3.7” x 2.8”)
1.15 kg (2.5 lbs)
Aluminum
Surface mount, tamper resistant
Powder coat, cool gray 2
±175° pan, -45° to +90° tilt, ±175° azimuth
45 cm (17.72”)
Electrical
Power Consumption
Power Source
22 W with external power
12.95 W with IEEE 802.3af Class 3 PoE
VDC: 12 V +/-10%, 22 W min
VAC: 24 V +/-10%, 28 VA min
PoE: IEEE802.3af Class 3 compliant
Environmental
Operating Temperature
Storage Temperature
-40 °C to +50 °C (-40 °F to 122 °F)
-10 °C to +70 °C (14 °F to 158 °F)
Certifications
Safety
UL 60950
CSA 60950
ROHS
WEEE
Environmental
IK10 Impact Rating
Electromagnetic Emissions FCC Part 15 Subpart B Class B
IC ICES-003 Class B
Electromagnetic Immunity EN 55024 Class B
EN 61000-4-4
EN 61000-4-5
14
CB Scheme
CE
UVV
C-Tick
Meets IP66 Weather Rating
EN 55022 Class B
EN 61000-4-2
EN 61000-4-3
EN 61000-4-6
EN 61000-4-11
English
Limited Warranty & Technical
Support
Avigilon warrants to the original consumer purchaser, that this product will
be free of defects in material and workmanship for a period of 3 years from
date of purchase.
The manufacturer’s liability hereunder is limited to replacement of the
product, repair of the product or replacement of the product with repaired
product at the discretion of the manufacturer. This warranty is void if the
product has been damaged by accident, unreasonable use, neglect,
tampering or other causes not arising from defects in material or
workmanship. This warranty extends to the original consumer purchaser of
the product only.
AVIGILON DISCLAIMS ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXCEPT
TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE
VALIDLY WAIVED.
No oral or written information, advice or representation provided by Avigilon,
its distributors, dealers, agents or employees shall create another warranty
or modify this warranty. This warranty states Avigilon’s entire liability and
your exclusive remedy against Avigilon for any failure of this product to
operate properly.
In no event shall Avigilon be liable for any indirect, incidental, special,
consequential, exemplary, or punitive damages whatsoever (including but
not limited to, damages for loss of profits or confidential or other information,
for business interruption, for personal injury, for loss of privacy, for failure to
meet any duty including of good faith or of reasonable care, for negligence,
and for any other pecuniary or other loss whatsoever) arising from the use of
or inability to use the product, even if advised of the possibility of such
damages. Since some jurisdictions do not allow the above limitation of
liability, such limitation may not apply to you.
This Limited Warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction.
Warranty service and technical support can be obtained by
contacting Avigilon Technical Support by phone at 1.888.281.5182 or
via email at support@Avigilon.com.
15
Download PDF

advertising