Pride Mobility CELEBRITY X Owner`s manual

CELEBRITY X SPORT
32 Wedgwood Road
Bicester, Oxon OX26 4UL
32 Wedgwood Road Bicester, Oxon OX26 4UL
*INFMANU3477*
SAFETY GUIDELINES
WARNING! An authorised Pride Dealer or qualified technician must perform the initial
setup of this scooter and must perform all of the procedures in this manual.
The symbols below are used throughout this owner's manual and on the scooter to identify warnings and
important information. It is very important for you to read them and understand them completely.
WARNING! Indicates a potentially hazardous condition/situation. Failure to follow
designated procedures can cause either personal injury, component damage or
malfunction. On the product, this icon is represented as a black symbol on a yellow
triangle with a black border.
MANDATORY! These actions should be performed as specified. Failure to perform
mandatory actions can cause personal injury and/or equipment damage. On the product,
this icon is represented as a white symbol on a blue dot.
PROHIBITED! These actions are prohibited. These actions should not be performed at
any time or in any circumstances. Performing a prohibited action can cause personal
injury and/or equipment damage. On the product, this icon is represented as a black
symbol with a red circle and a red slash.
Please fill out the following information for quick reference:
Pride Dealer: _______________________________________________________________________
Address: __________________________________________________________________________
Phone Number: _________________________
Purchase Date: _________________________
Serial Number: ____________________________
NOTE: This owner’s manual is compiled from the latest specifications and product information available at the time of publication. We reserve the right to make changes as they become necessary. Any
changes to our products may cause slight variations between the illustrations and explanations in this
manual and the product you have purchased. The latest/current version of this manual is available on
our website.
Copyright © 2009
Pride Mobility Products Ltd.
INFMANU3477/RevC/June 2009
CONTENTS
I.
INTRODUCTION .......................................................................................................................4
II.
SAFETY ........................................................................................................................................5
III. YOUR SCOOTER ......................................................................................................................18
IV. BATTERIES AND CHARGING ..........................................................................................23
V.
OPERATION .............................................................................................................................28
VI. COMFORT ADJUSTMENTS ..............................................................................................30
VII. DISASSEMBLY AND ASSEMBLY ...................................................................................33
VIII. BASIC TROUBLESHOOTING ..........................................................................................36
IX. CARE AND MAINTENANCE ..............................................................................................38
X.
WARRANTY ..............................................................................................................................42
APPENDIX I - SPECIFICATIONS .............................................................................................43
Celebrity X Sport
www.pridemobility.com
3
I. INTRODUCTION
SAFETY
Welcome to Pride Mobility Products Ltd. (Pride). The product you have purchased combines state-of-theart components with safety, comfort and styling in mind. We are confident the design features will provide
you with the conveniences you expect during your daily activities. Understanding how to safely operate
and care for this product should bring you years of trouble free operations and service.
Read and follow all instructions, warnings and notes in this manual and all other accompanying literature
before attempting to operate this product for the first time. In addition, your safety depends upon you, as
well as your dealer, carer or healthcare professional in using good judgement.
If there is any information in this manual which you do not understand or if you require additional assistance for setup or operation, please contact your authorised Pride Dealer. Failure to follow the instructions, warnings and notes in this manual and those located on your Pride product can result in
personal injury or product damage and will void Pride’s product warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter or modify this product
or remove or render inoperable or unsafe any guards, shields or other safety features of this product; fail,
refuse or neglect to install any retrofit kits from time to time provided by Pride to enhance or preserve the
safe use of this product.
SHIPPING AND DELIVERY
Before using your scooter, make sure your delivery is complete as some components may be individually
packaged. If you do not receive a complete delivery, please contact your authorised Pride Dealer immediately. Where damage has occurred during transport, either to the packaging or content, please contact the
delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments and suggestions about this manual. We would also like to hear
about the safety and reliability of your new scooter and about the service you received from your authorised Pride Dealer. Please notify us of any change of address, so we can keep you apprised of important
information about safety, new products and new options that can increase your ability to use and enjoy
your scooter. Please feel free to contact us at the address below:
Pride Mobility Products Ltd.
32 Wedgwood Road
Bicester, Oxon OX26 4UL
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact
us and we will be glad to send you a new one immediately.
4
www.pridemobility.com
Celebrity X Sport
II. SAFETY
PRODUCT SAFETY SYMBOLS
The symbols below are used on the scooter to identify warnings, mandatory actions and prohibited actions.
It is very important for you to read and understand them completely.
Read and follow the information in the owner’s manual.
Pinch/Crush points created during assembly.
Corrosive chemicals contained in battery.
EMI-RFI- This product has been tested and passed at an immunity level of 20 V/m.
Do not place your scooter in freewheel mode while on a declilne.
Do not place your scooter in freewheel mode while on an incline.
Explosive conditions exist!
Celebrity X Sport
www.pridemobility.com
5
II. SAFETY
Maximum seating weight.
Unlocked and in freewheel mode.
Place unit on level ground and stand to one side when changing from drive
mode to freewheel mode or freewheel mode to drive mode.
Locked and in drive mode.
Front-to-rear plug orientation.
Wear safety goggles.
Do not mistake the tiller adjustment lever for a brake.
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
condition.
6
www.pridemobility.com
Celebrity X Sport
II. SAFETY
Do not raise or lower the power seat while the scooter is in motion.
Keep your hands away from the tyres when driving. Be aware that loose fitting
clothing can become caught in the drive tyres.
Do not remove anti-tip wheels.
Do not use a cell phone, walkie/talkie, laptop or other radio transmitter while
operating.
Avoid exposure to rain, snow, ice, salt or standing water whenever possible.
Maintain and store in a clean and dry condition.
Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug
access.
Do not connect an extension lead to the AC/DC converter or the battery charger.
Keep tools and other metal objects away from battery terminals. Contact with tools
can cause electrical shock.
Celebrity X Sport
www.pridemobility.com
7
II. SAFETY
Do not allow unsupervised children to play near the scooter while the batteries
are charging.
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and
new batteries. Always replace both batteries at the same time.
Battery charger for indoor use only.
Disposal and recycling—Contact your authorised Pride Dealer for information on
proper disposal of your Pride product and its packaging.
Contains lead.
8
www.pridemobility.com
Celebrity X Sport
II. SAFETY
GENERAL
MANDATORY! Do not operate your new scooter for the first time without completely
reading and understanding this owner’s manual.
Your scooter is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an
extensive variety of products to best fit the individual needs of the scooter user. Please be aware that the
final selection and purchasing decision regarding the type of scooter to be used is the responsibility of the
scooter user who is capable of making such a decision and his/her healthcare professional (i.e., medical
doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted
the scooter to the user and has assisted the prescribing healthcare professional and/or the authorised Pride
Dealer in the instruction process for the use of the product.
There are certain situations, including some medical conditions, where the scooter user will need to practice operating the scooter in the presence of a trained attendant. A trained attendant can be defined as a
family member or care professional specially trained in assisting a scooter user in various daily living
activities.
As you begin using your scooter during daily activities, you will probably encounter situations in which
you will need some practice. Simply take your time and you will soon be in full and confident control as
you manoeuvre through doorways, on and off lifts, up and down ramps and over moderate terrain.
Below are some precautions, tips and other safety considerations that will help you become accustomed
to operating the scooter safely.
MODIFICATIONS
Pride has designed and engineered your scooter to provide maximum mobility and utility. However, under
no circumstances should you modify, add, remove or disable any feature, part or function of your scooter.
WARNING! Do not modify your scooter in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
REMOVABLE PARTS
WARNING! Do not attempt to lift or move your scooter by any of its removable parts,
including the armrests, seat or shroud.
PRE-RIDE SAFETY CHECK
Get to know the feel of your scooter and its capabilities. Pride recommends that you perform a safety check
before each use to make sure your scooter operates smoothly and safely.
Celebrity X Sport
www.pridemobility.com
9
II. SAFETY
Perform the following inspections prior to using your scooter:
Check for proper tyre inflation (if equipped with pneumatic tyres).
Check all electrical connections. Make sure they are tight and not corroded.
Check all harness connections. Make sure they are secured properly.
Check the brakes.
Check battery charge.
If you discover a problem, contact your authorised Pride Dealer for assistance.
TYRE INFLATION
If your scooter is equipped with pneumatic tyres, you should check or have the air pressure checked at least
once a week. Proper inflation pressures will prolong the life of your tyres and help ensure the smooth
operation of your scooter.
WARNING! It is critically important that the psi/bar/kPa air pressure rating indicated on
each tyre be maintained in pneumatic tyres at all times. Do not underinflate or overinflate
your tyres. Low pressure may result in loss of control and overinflated tyres may burst.
Failure to maintain the psi/bar/kPa air pressure rating indicated on pneumatic tyres at all
times may result in tyre and/or wheel failure.
WARNING! Inflate your scooter tyres from a regulated air source with an available
pressure gauge. Inflating your tyres from an unregulated air source could overinflate
them, resulting in a burst tyre.
NOTE: If the tyres on your scooter list the psi rating only, use the following conversion formulas to
find the bar or kPa rating: bar = psi x 0.06895; kPa = psi x 6.89476.
WEIGHT LIMITATIONS
Your scooter is rated for a maximum weight capacity. Refer to the specifications table for information.
MANDATORY! Stay within the specified weight capacity of your scooter. Exceeding the
weight capacity voids your warranty. Pride will not be held responsible for injuries and/
or property damage resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your scooter. Carrying passengers on your
scooter may affect the centre of gravity, resulting in a tip or a fall.
INCLINE INFORMATION
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe
access. Some ramps may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your scooter.
Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
Take wide swings with your scooter around any tight corners. If you do that, the scooter’s rear wheels
will follow a wide arc, not cut the corner short and not bump into or get hung up on any railing corners.
When driving down a ramp, keep the scooter’s speed adjustment set to the slowest speed setting to
ensure a safely controlled descent.
Avoid sudden stops and starts.
10
www.pridemobility.com
Celebrity X Sport
II. SAFETY
When climbing an incline, try to keep your scooter moving. If you must stop, start up again slowly and
then accelerate cautiously. When driving down an incline, do so by setting the speed adjustment dial to the
slowest setting and driving in the forward direction only. If your scooter starts to move down the incline
faster than you anticipated or desired, allow it to come to a complete stop by releasing the throttle control
lever. Then push the throttle control lever forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the scooter in
freewheel mode, especially while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the
face of the incline. Drive your scooter straight up the incline. This greatly
reduces the possibility of a tip or a fall. Always exercise extreme caution when
negotiating an incline.
WARNING! Do not drive your scooter across the side of an incline or diagonally
up or down an incline; do not stop, if possible, while driving up or down an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e.,
areas covered with snow, ice, cut grass or wet leaves).
WARNING! Even though your scooter is capable of climbing slopes greater than
those illustrated in figure 1, do not, under any circumstances, exceed the incline
guidelines or any other specifications presented in this manual. Doing so could
cause instability in your scooter.
Handicap public access ramps are not subject to government regulation in all countries and therefore do
not necessarily share the same standard percent of slope. Other inclines may be natural or, if man-made,
not designed specifically for scooters. Figure 1 illustrates your scooter’s stability and its ability to climb
grades under various weight loads and under controlled testing conditions.
These tests were conducted with the scooter’s seat in the highest position and adjusted rearward on the seat
base to its farthest rearward position. Use this information as a guideline. Your scooter’s ability to travel
up inclines is affected by your weight, your scooter’s speed, your angle of approach to the incline and your
scooter setup.
136-159 kg/
21-25 stone
(350 lbs.)
15.8% (9˚)
Figure 1. Maximum Recommended Incline Angle
WARNING! Any attempt to climb or descend a slope steeper than what is shown in figure
1 may put your scooter in an unstable position and cause it to tip.
WARNING! Never carry an oxygen tank weighing more than 6 kg (13 lbs.). Never fill the
front or rear basket with contents exceeding 6 kg (13 lbs.).
Celebrity X Sport
www.pridemobility.com
11
II. SAFETY
When you approach an incline, it is best to lean forward. See figures 2 and 2A. This shifts the centre of
gravity of you and your scooter toward the front of the scooter for improved stability.
NOTE: When negotiating ramps, if the throttle control lever is released while moving forward, the
powered scooter may "rollback" approximately 30.5 cm (1 foot) before the brake engages. If the throttle
control lever is released while moving in reverse, the powered scooter may "rollback" approximately
one metre (3 feet) before the brake engages.
Figure 2. Normal Driving Position
Figure 2A. Increased Stability Driving Position
CORNERING INFORMATION
Excessively high cornering speeds can create the possibility of tipping. Factors which affect the possibility
of tipping include, but are not limited to, cornering speed, steering angle (how sharply you are turning),
uneven road surfaces, inclined road surfaces, riding from an area of low traction to an area of high traction
(such as passing from a grassy area to a paved area – especially at high speed while turning) and abrupt
directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a
corner, reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your scooter
from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable centre of
gravity. When using your scooter at higher speeds, do not corner sharply. This greatly
reduces the possibility of a tip or fall.
BRAKING INFORMATION
Your scooter is equipped with these powerful brake systems:
Regenerative: Uses electricity to rapidly slow the vehicle when the throttle control lever returns to the
centre/stop position.
Disc Park Brake: Activates mechanically after regenerative braking slows the vehicle to near stop or
when power is removed from the system for any reason.
Handbrake: Gives you additional stopping power when you squeeze it.
12
www.pridemobility.com
Celebrity X Sport
II. SAFETY
OUTDOOR DRIVING SURFACES
Your scooter is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed of concrete or tarmac. However, Pride recognises that there will be times when you will
encounter other surface types. For this reason, your scooter is designed to perform admirably on packed
soil, grass and gravel. Feel free to use your scooter safely on lawns and in park areas.
Reduce your scooter’s speed when driving on uneven terrain and/or soft surfaces.
Avoid tall grass that can become tangled in the running gear.
Avoid loosely packed gravel and sand.
Do not use your scooter in fresh or salt water.
Do not use your scooter at the edge of a stream, lake, or ocean.
If you feel unsure about a driving surface, avoid that surface.
PUBLIC STREETS AND ROADWAYS
WARNING! Exercise extreme caution when operating the scooter on footpaths,
pavements, bridleways, pedestrian areas and roads. Obey all local pedestrian traffic rules.
STATIONARY OBSTACLES (STEPS, KERBS, ETC.)
To navigate up over a kerb or stationary onstacle:
1. Approach the kerb or obstacle slowly, and make sure the scooter is traveling perpendicular to the
obstacle. See figure 3.
2. Increase the forward speed just before the front wheel(s) some in contact with the obstacle.
3. Reduce the forward speed only after the rear wheels have cleared the obstacle.
To navigate down a kerb or stationary obstacle:
1. Approach the kerb or obstacle slowly, and make sure the scooter is traveling perpendicular to the
obstacle. See figure 3.
2. Reduce the forward speed just before the front wheel(s) come in contact with the obstacle.
3. Increase the forward speed only after the rear wheels have cleared the obstacle and you are once again
on a level surface.
WARNING! Do not attempt to have your scooter climb or descend an obstacle that is
inordinately high.
WARNING! Do not attempt to have your scooter proceed rearward down any step, kerb
or other obstacle. This may cause the scooter to tip.
KERB
KERB
Figure 3. Correct Kerb Approach
Celebrity X Sport
Figure 4. Incorrect Kerb Approach
www.pridemobility.com
13
II. SAFETY
WARNING! Be sure your scooter is traveling perpendicular to any kerb you may be
required to ascend or descend. See figures 3 and 4.
WARNING! Even though your scooter may be capable of handling greater obstacles, Pride
recommends that you do not attempt to negotiate a curb that has a height greater than
2 in. (5 cm). Doing so could cause instability in your scooter.
INCLEMENT WEATHER PRECAUTIONS
Exposure of your scooter to inclement weather conditions should be avoided whenever possible. If suddenly caught up in rain, snow, severe cold or heat while operating your scooter, proceed to shelter at the
earliest opportunity. Thoroughly dry your scooter before storing, charging or operating your scooter.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions and on icy/slippery
surfaces may have an adverse affect on the electrical system. Maintain and store your
scooter in a dry and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of
upholstered and non-upholstered items on the scooter, possibly resulting in skin
irritation. Exercise caution when using your scooter in extremely hot or cold conditions
or when exposing your scooter to direct sunlight for prolonged periods of time.
FREEWHEEL MODE
Your scooter is equipped with a manual freewheel lever that, when engaged, allows the scooter to be pushed.
For more information about how to place your scooter into and out of freewheel mode, see III. “Your Scooter.”
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
Disengage the drive motors only on a level surface.
Ensure the key is removed from the key switch.
Stand to the side of the scooter to engage or disengage freewheel mode. Never sit
on a scooter to do this.
After you have finished pushing your scooter, always return it to the drive mode to
lock the brakes.
An added feature built into the scooter is “push-too-fast” protection which safeguards the scooter against
gaining excessive speed while in freewheel mode.
“Push-too-fast” operates differently depending on which of two conditions exists:
If the key is switched “off” while in freewheel mode, the scooter’s controller activates regenerative
braking when the scooter is pushed faster than a maximum threshold which has been preprogrammed.
In this case, the controller is acting as a speed governor.
If the key is switched “on” while in freewheel mode, you will encounter considerable resistance at any
speed. This prevents the scooter from gaining unwanted momentum should the manual freewheel lever
inadvertently be released while driving the scooter.
STAIRS AND ESCALATORS
Scooters are not designed to travel up or down stairs or escalators. Always use a lift.
WARNING! Do not use your scooter to negotiate steps or escalators.
DOORS
Determine if the door opens toward or away from you.
Use your hand to turn the knob or push the handle or push-bar.
Drive your scooter gently and slowly forward to push the door open. Or drive your scooter gently and
slowly rearwards to pull the door open.
14
www.pridemobility.com
Celebrity X Sport
II. SAFETY
LIFTS
Modern lifts have a door edge safety mechanism that, when pushed, reopens the door(s).
If you are in the doorway of a lift when the door(s) begin to close, push on the rubber door edge or
allow the rubber door edge to contact the scooter and the door will reopen.
Use care that handbags, packages or scooter accessories do not become caught in lift doors.
NOTE: If your scooter’s turning radius is greater than 1500 mm (60 in), it may be difficult to manoeuvre in lifts and building entrances. Use caution when attempting to turn or manoeuvre your scooter in
small spaces and avoid areas that might pose a problem.
LIFT SYSTEMS/ELEVATION PRODUCTS
If you will be transporting your scooter during travel, you may find it necessary to use a vehicle-mounted
lift system or elevation product to aid in transportation. Pride recommends that you closely review the
warnings, instructions, specifications, and safety information set forth by the manufacturer of the lift/
elevation product before using that product.
WARNING! Not all lift systems/elevation products are rated for use with an occupied
mobility device. Pride recommends that you do not remain seated in your scooter when
it is being used in connection with any type of lift system/elevation product unless:
That product is rated for occupied use by the manufacturer.
You are able to occupy your mobility device in strict conformity with the warnings,
instructions, specifications, and safety guidelines set forth by the manufacturer.
WARNING! Always turn off the power to the unit when you are being transferred via an
elevation product. Failure to do so may result in accidental throttle control lever contact,
resulting in unintended movement and personal injury or product damage.
BATTERIES
In addition to following the warnings below, be sure to comply with all other battery handling information.
MANDATORY! Battery posts, terminals and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash
hands after handling.
WARNING! Scooter batteries are heavy. See specifications table. If you are
unable to lift that much weight, be sure to get help. Use proper lifting techniques
and avoid lifting beyond your capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen
battery. Changing a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables
must be connected to positive (+) battery terminals/posts. BLACK (-) cables must
be connected to negative (-) battery terminals/posts. Protective caps must be
installed over all battery terminals. REPLACE cables immediately if damaged.
BATTERY DISPOSAL AND RECYCLING
If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and call your
authorised Pride Dealer for instructions on disposal. Your authorised Pride Dealer will also have the necessary information on battery recycling, which is our recommended course of action.
PREVENTING UNINTENDED MOVEMENT
WARNING! If you anticipate being seated in a stationary position for an extended period
of time, turn off the power. This will prevent unexpected motion from inadvertent throttle
control lever contact.
Celebrity X Sport
www.pridemobility.com
15
II. SAFETY
MOTOR VEHICLE TRANSPORT
Pride recommends that you do not remain seated in your scooter while traveling in a motor vehicle. The
scooter should be stowed in the boot of a car or in the back of a truck or van with the batteries removed
and properly secured. In addition, all removable scooter parts, including the armrests, seat and shroud
should be removed and/or properly secured during motor vehicle transport.
WARNING! Although your scooter may be equipped with a positioning belt, this belt is not
designed to provide restraint during motor vehicle transport. Anyone travelling in a motor
vehicle should be properly secured in the motor vehicle seat with safety belts fastened
securely.
WARNING! Do not sit on your scooter while it is in a moving vehicle.
WARNING! Always be sure your scooter and its batteries are properly secured when it is
being transported. Batteries should be secured in an upright position and protective caps
should be installed on the battery terminals. Batteries should not be transported with any
flammable or combustible items.
POSITIONING BELTS
Your authorised Pride Dealer, therapist(s) and other healthcare professionals are responsible for determining your requirement for a positioning belt in order to operate your scooter safely.
WARNING! If you require a positioning belt to safely operate your scooter, make sure it
is fastened securely in order to reduce the possibility of a fall from the scooter.
GETTING ONTO AND OFF YOUR SCOOTER
Getting onto and off of your scooter requires a good sense of balance. Please observe the following safety
tips when getting onto and off of your scooter:
Remove the key from the key switch.
Ensure that your scooter is not in freewheel mode. See III. “Your Scooter.”
Make certain that the seat is secured into place.
Pivot the armrests up to make getting onto and off of the scooter easier.
WARNING! Position yourself as far back as possible in the scooter seat to prevent the
scooter from tipping.
WARNING! Avoid putting all of your weight on the scooter armrests and do not use the
armrests for weight bearing purposes, such as transfers. Such use may cause the
scooter to tip, resulting in a fall from the scooter and/or personal injury.
WARNING! Avoid putting all of your weight on the floorboard. Such use may cause the
scooter to tip.
REACHING AND BENDING
Avoid reaching or bending while driving your scooter. Bending forward creates the risk of accidental throttle
control lever contact. Bending to the side while seated creates the risk of tipping. It is important to maintain
a stable centre of gravity and keep the scooter from tipping. Pride recommends that the scooter user determine
his/her personal limitations and practice bending and reaching in the presence of a qualified attendant.
WARNING! Do not bend, lean or reach for objects if you have to pick them up from the
scooter deck or from either side of the scooter. Movements such as these may change your
centre of gravity and the weight distribution of the scooter and cause your scooter to tip.
PROHIBITED! Keep your hands away from the tyres when driving. Be aware that loose
fitting clothing can become caught in drive tyres.
16
www.pridemobility.com
Celebrity X Sport
II. SAFETY
PRESCRIPTION DRUGS/PHYSICAL LIMITATIONS
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues when taking prescribed or over-the-counter drugs or when the user has specific
physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter
medication or if you have certain physical limitations. Some medications and limitations
may impair your ability to operate your scooter in a safe manner.
ALCOHOL/SMOKING
The scooter user must exercise care and common sense when operating his/her scooter. This includes
awareness of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your scooter while you are under the influence of alcohol, as
this may impair your ability to operate the scooter in a safe manner.
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated on
your scooter, although the scooter seat has passed the necessary testing requirements
for cigarette smoking. You must adhere to the following safety guidelines if you decide
to smoke cigarettes while seated on your scooter.
Do not leave lit cigarettes unattended.
Keep ashtrays a safe distance from the seat cushions.
Always make sure cigarettes are completely extinguished before disposal.
ELECTROMAGNETIC AND RADIO FREQUENCY INTERFERENCE (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency
waves can have an adverse affect on the performance of electrically-powered mobility
vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile
two-way radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters,
wireless computer links, microwave signals, paging transmitters and medium-range mobile transceivers
used by emergency vehicles. In some cases, these waves can cause unintended movement or damage to
the control system. Every electrically-powered mobility vehicle has an immunity (or resistance) to EMI.
The higher the immunity level, the greater the protection against EMI. This product has been tested and
has passed at an immunity level of 20 V/M.
WARNING! Be aware that cell phones, two-way radios, laptops and other types of radio
transmitters may cause unintended movement of your electrically-powered mobility
vehicle due to EMI. Exercise caution when using any of these items while operating your
mobility vehicle and avoid coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered
mobility vehicle can increase the susceptibility of the vehicle to EMI. Do not modify your
scooter in any way not authorised by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance
of other electrical devices located nearby, such as alarm systems.
NOTE: For further information on EMI/RFI, visit the Resource Centre on www.pridemobility.com. If
unintended motion or brake release occurs, turn your scooter off as soon as it is safe to do so. Contact
your authorised Pride Dealer to report the incident.
Celebrity X Sport
www.pridemobility.com
17
III. YOUR SCOOTER
TILLER CONSOLE
The tiller console houses all of the controls needed to drive your scooter, including the speed adjustment dial, throttle
control lever, battery condition meter, handbrake, hi-low switch, lights switch and horn buttons. See figure 5.
PROHIBITED! Do not expose the tiller console to moisture. In the event that the tiller
console does become exposed to moisture, do not attempt to operate your scooter until
the tiller console has dried thoroughly.
BATTERY CONDITION METER
HANDBRAKE LEVER
STATUS LED
SPEED ADJUSTMENT DIAL
KEY SWITCH
THROTTLE
CONTROL
LEVER
THROTTLE
CONTROL
LEVER
LEFT TURN INDICATOR
BUTTON
RIGHT TURN
INDICATOR BUTTON
HORN BUTTON
HORN BUTTON
HI-LOW SWITCH
HAZARD LIGHTS SWITCH
LIGHTS SWITCH
Figure 5. Tiller Console
Horn Buttons
These buttons activate a warning horn. Your scooter must be powered up for the horn to be operational.
Do not hesitate to use the warning horn when doing so may prevent accident or injury.
Key Switch
Insert the key into the key switch and turn it clockwise to power up (turn on) your scooter.
Turn the key anticlockwise to power down (turn off) your scooter.
WARNING! If the key is moved to the “off” position while your scooter is in motion, the
electronic brakes will engage and your scooter will come to an abrupt stop!
Battery Condition Meter
When the key is fully inserted and turned clockwise to power up your scooter, this meter indicates the
approximate battery voltage strength. For further information on battery charging, see IV. “Batteries and
Charging.”
Turn Indicator Buttons
Use these buttons to turn on the left and right turn indicator (amber) lights. See figure 5.
Push the left button to activate the left turn indicator light.
Push the right button to activate the right turn indicator light.
The indicators are timed to shut off automatically.
18
www.pridemobility.com
Celebrity X Sport
III. YOUR SCOOTER
Status LED
The status LED alerts you to electrical problems that may occur with the scooter. The LED remains constantly lit while your scooter is on. If your scooter develops an electrical problem, the status LED will flash
a code. SeeVIII. “Basic Troubleshooting” for flash codes.
Hi-Low Switch
Toggle the switch forward (HI) and your scooter’s maximum speed is 12.82 km/h (8 mph).
Toggle the switch rearward (LOW) and your scooter’s maximum speed is 6.3 km/h (4 mph).
Lights Switch
This switch controls your scooter’s lights.
Toggle the switch forward to turn on your scooter’s front top light and running lights.
Toggle the switch to the middle to turn off the scooter’s lights.
Toggle the switch rearward to turn on all the scooters lights (upper and lower front and running lights).
WARNING! Scooter users are required to use their lights when visibility is restricted—day
or night.
Handbrake Lever
This lever provides you with additional stopping power. Release the throttle control lever and gently
squeeze the handbrake lever to come to a stop.
NOTE: If you do not release the throttle control lever before using the handbrake, your scooter may not
come to a complete stop.
Throttle Control Lever
This lever allows you to control the forward speed and the reverse speed of your scooter up to the maximum speed you preset with the speed adjustment dial.
To Move Forward use either of the following:
Use your left thumb to push the left side of the throttle control lever.
Use your right hand fingers to pull back on the right side of the throttle control lever.
To Move Rearward use either of the following:
Use your right thumb to push the right side of the throttle control lever.
Use your left hand fingers to pull back on the left side of the throttle control lever.
Release the throttle control lever and allow your scooter to come to a complete stop before engaging the
other side of the lever. When the throttle control lever is completely released, it automatically returns to
the centre “stop” position and engages your scooter’s brakes.
Speed Adjustment Dial
This dial allows you to preselect and limit your scooter’s top speed.
The image of the tortoise represents the slowest speed setting.
The image of the hare represents the fastest speed setting.
Celebrity X Sport
www.pridemobility.com
19
III. YOUR SCOOTER
Off-board Charger Port
The off-board charger power lead plugs into this port
when charging the batteries. See figure 6.
Tiller Console Fuses
These 1-amp fuses help protect your scooter’s front
lighting, turn indicator and key switch console systems from receiving an overload of electrical current.
The fuses used in your scooter are the same type used
in automobiles. See figure 7. See IX. “Care and Maintenance” for fuse replacement.
Figure 6. Off-board Charger Port
REAR SECTION
The batteries, the main circuit breaker (reset button),
the manual freewheel lever, the anti-tip wheels and
the motor/transaxle assembly are located on the rear
section of your scooter. See figure 8.
Motor/Transaxle Assembly
The motor/transaxle assembly is an electromechanical unit that converts electrical energy from your
scooter’s batteries into the controlled mechanical
energy that drives the scooter’s wheels.
Batteries
The batteries store electrical energy that powers your
scooter. See IV. “Batteries and Charging ” for information on how to charge your scooter batteries.
SPARE
UPPER HEADLIGHT
LOWER HEADLIGHT
LEFT TURN INDICATOR
RIGHT TURN INDICATOR
Figure 7. Tiller Console Fuses
BATTERY
BATTERY
MANUAL FREEWHEEL LEVER
MOTOR/TRANSAXLE ASSEMBLY
ANTI-TIP WHEELS
Figure 8. Rear Section
20
www.pridemobility.com
Celebrity X Sport
III. YOUR SCOOTER
Anti-tip Wheels
The anti-tip wheels are an integral and important safety feature designed to help prevent your scooter from
tipping rearwards on an incline. They are bolted to the frame at the rearmost part of your scooter.
PROHIBITED! Do not remove the anti-tip wheels or modify your scooter in any way that
is not authorised by Pride.
Manual Freewheel Lever
Whenever you need or want to push your scooter for short distances, you can put it in freewheel mode.
1. Remove the key from the key switch.
2. Push forward on the manual freewheel lever to disable the drive system and the brake system. You may
now push your scooter.
3. Pull back on the manual freewheel lever to reengage the drive and the brake systems and take your
scooter out of freewheel mode.
WARNING! When your scooter is in freewheel mode, the braking system is disengaged.
Disengage the drive motors only on a level surface.
Ensure the key is removed from the key switch.
Stand to the side of the scooter to engage or disengage freewheel mode. Never sit on
a scooter to do this.
After you have finished pushing your scooter, always return it to the drive mode to
lock the brakes.
NOTE: If the scooter is placed in freewheel mode (manual freewheel lever forward) while the key is in
the “on” position, the scooter will not run until the manual freewheel lever is pushed rearward and the
key is turned to the “off” position, then back to the “on” position.
Main Circuit Breaker (Reset Button)
When the voltage in the batteries becomes low or
your scooter is heavily strained because of excessive loads, the main circuit breaker may trip to
protect the motor and electronics from damage.
When the breaker trips, the entire electrical system shuts down. See figure 9.
The reset button pops out when the breaker
trips.
Allow a minute or so for the electronics to
“rest.”
Push in the reset button to reset the breaker.
If the breaker trips frequently, you may need
to charge the batteries more often or have
your authorised Pride Dealer perform a load
test on the batteries.
If the main circuit breaker trips repeatedly,
see your authorised Pride Dealer for service.
Celebrity X Sport
MAIN CIRCUIT BREAKER (RESET BUTTON)
Figure 9. Main Circuit Breaker (Reset Button)
www.pridemobility.com
21
III. YOUR SCOOTER
SECUREMENT POINTS
Steel loops welded to the anti-tip wheel brackets and/or front frame components of your scooter provide
securement points. See figures 10 and 10A. These should only be used with an unoccupied scooter and
secured by an approved securement system (tie-downs) in accordance with the manufacturer’s instructions. Pride makes no representation of suitability for use with specific securement systems nor can we
anticipate the various situations that might arise in use of public transportation systems. For detailed
instructions on the use of securement systems, refer to the applicable municipal transit authority and/or
manufacturer of the system used.
WARNING! DO NOT leave the scooter in freewheel mode when securing it for transport.
WARNING! DO NOT use your scooter as a seat in a moving vehicle.
SECUREMENT POINTS
SECUREMENT POINTS
Figure 10. Rear Securement Points
22
Figure 10A. Front Securement Points
www.pridemobility.com
Celebrity X Sport
IV. BATTERIES AND CHARGING
Your scooter requires two long-lasting, 12-volt, deep-cycle batteries that are sealed and maintenance free.
They are recharged by an off-board charging system.
Charge your scooter’s batteries prior to using it for the first time.
Keep the batteries fully charged to keep your scooter running smoothly.
READING YOUR BATTERY VOLTAGE
The battery condition meter on the tiller console indicates the
approximate strength of your batteries using a colour code.
From right to left, green indicates fully charged batteries, yellow a draining charge and red indicates that an immediate
recharge is necessary. See figure 11. To ensure the highest
accuracy, the battery condition meter should be checked
while operating your scooter at full speed on a dry, level surface.
CHARGING YOUR BATTERIES
Figure 11. Battery Condition Meter
PROHIBITED! Never use an extension lead to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary,
properly install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug
access.
PROHIBITED! Do not allow unsupervised children to play near the scooter while the
batteries are charging. Pride recommends that you do not charge the batteries while the
scooter is occupied.
MANDATORY! Read the battery charging instructions in this manual and in the manual
supplied with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the
scooter and battery charger away from sources of ignition such as flames or sparks and
provide adequate ventilation when charging the batteries.
WARNING! Ensure that both ends of the charger power lead are clean and dry before
plugging the charger power lead into the off-board charger port or the electrical outlet.
WARNING! Inspect the battery charger, wiring and connectors for damage before each use.
Contact your authorised Pride Dealer if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does not
appear to be working correctly, contact your authorised Pride Dealer.
WARNING! If the off-board battery charger is equipped with cooling slots, then do not
attempt to insert objects through these slots.
WARNING! If your battery charger has not been tested and approved for outdoor use, then
do not expose it to adverse or extreme weather conditions. If the battery charger is
exposed to adverse or extreme weather conditions, then it must be allowed to adjust to the
difference in environmental conditions before use indoors. Refer to the manual supplied
with the battery charger for more information.
Celebrity X Sport
www.pridemobility.com
23
IV. BATTERIES AND CHARGING
Follow these easy steps to charge your batteries
safely:
1. Position the front of your scooter close to a standard electrical outlet.
2. Remove the key from the key switch.
3. Make sure that the manual freewheel lever is in
the drive position.
4. Plug the 3-pin charger power lead into the offboard charger port. See figure 6.
5. Extend the charger power lead and plug it into
the electrical outlet. We recommend that you
charge the batteries for 8 to 14 hours.
6. When the batteries are fully charged, unplug the
charger power lead from the electrical outlet
and then from the off-board charger port.
PLUGS INTO THE OFF-BOARD
CHARGER PORT
PLUGS INTO ELECTRICAL OUTLET
Figure 12. Off-board Charger
NOTE: The LED lights on the charger indicate different charger conditions at various times: charger
power on, charging in progress and charging complete. Refer to the manual supplied with the charger
for a complete explanation of these indicators.
NOTE: There is a charger inhibit function on your scooter. The scooter will not run and the battery
condition meter will not operate while the batteries are charging.
FREQUENTLY ASKED QUESTIONS
How does the charger work?
When your scooter’s battery voltage is low, the charger works harder, sending more electrical current to
the batteries to bring up their charge. As the batteries approach a full charge, the charger sends less and
less electrical current. When the batteries are fully charged, the current sent from the charger is at nearly
zero amperage. Therefore, when the charger is plugged in, it maintains the charge on your scooter’s batteries, but does not overcharge them. We do not recommend that you charge your scooter’s batteries for
more than 24 consecutive hours.
Can I use a different charger?
Chargers are selected precisely for particular applications and are especially matched to the type, size and
chemical formulation of specific batteries. For the safest and most efficient charging of your scooter’s
batteries, we recommend use of the charger supplied as original equipment with your Pride product only.
Any charging method resulting in batteries being charged individually is especially prohibited.
What if my scooter’s batteries won’t charge?
Ensure the red (+) and black (-) battery cables are connected properly to the battery terminals.
Ensure both battery harnesses that extend from the batteries are plugged into their mating harness
leading to the charger.
Ensure both ends of the charger power lead are inserted fully.
How often must I charge the batteries?
Two major factors must be considered when deciding how often to charge your scooter’s batteries:
All day scooter use on a daily basis.
Infrequent or sporadic scooter use.
24
www.pridemobility.com
Celebrity X Sport
IV. BATTERIES AND CHARGING
With these considerations in mind, you can determine how often and for how long you should charge your
scooter’s batteries. We designed the off-board charger so that it will not overcharge your scooter’s batteries. However, you may encounter some problems if you do not charge your batteries often enough and if
you do not charge them on a regular basis. Following the guidelines below will provide safe and reliable
battery operation and charging.
If you use your scooter daily, charge its batteries as soon as you finish using it for the day. Your scooter
will be ready each morning. We recommend that you charge your scooter’s batteries for 8 to 14 hours
after daily use.
If you use your scooter once a week or less, charge its batteries at least once a week for 12 to 14 hours
at a time.
Keep your scooter’s batteries fully charged.
Avoid deeply discharging your scooter’s batteries.
How can I ensure maximum battery life?
Fully charged deep-cycle batteries provide reliable performance and extended battery life. Keep your
scooter’s batteries fully charged whenever possible. Protect your scooter and batteries from extreme heat
or cold. Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme
temperatures or stored without a full charge may be permanently damaged, causing unreliable
performance and limited service life.
How can I get maximum range or distance per charge?
Rarely will you have ideal driving conditions - smooth, flat, hard driving surfaces with no wind or curves.
Often, you will face hills, pavement cracks, uneven and loosely packed surfaces, curves and wind, all of
which affect the distance or running time per battery charge. Below are a few suggestions for obtaining
the maximum range per battery charge.
Always fully charge your scooter’s batteries prior to daily use.
Maintain but do not exceed the psi/bar/kPa air pressure rating indicated on pneumatic tyres.
Plan your route ahead to avoid as many hills, cracked, broken or soft surfaces as possible.
Limit your baggage weight to essential items.
Try to maintain an even speed while your scooter is in motion.
Avoid stop-and-go driving.
What type and size of battery should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. Both AGM and Gel-Cell are deepcycle batteries that are similar in performance. Do not use wet-cell batteries, which have removable caps.
WARNING! Corrosive chemicals are contained in batteries. Use only AGM or GelCell batteries to reduce the risk of leakage or explosive conditions.
NOTE: Sealed batteries are not serviceable. Do not remove the caps.
Celebrity X Sport
www.pridemobility.com
25
IV. BATTERIES AND CHARGING
How do I change a battery in my scooter?
MANDATORY! Battery posts, terminals and related accessories contain lead and
lead compounds. Wear goggles and gloves when handling batteries and wash
hands after handling.
WARNING! Always use two batteries of the exact same type, chemistry and amphour (Ah) capacity. Refer to the specifications table in this manual and in the
manual supplied with the battery charger for recommended type and capacities.
WARNING! Contact your authorised Pride Dealer if you have any questions
regarding the batteries in your scooter.
WARNING! Do not replace the batteries while the scooter is occupied.
WARNING! The batteries on your scooter should only be serviced or replaced by
an authorised Pride Dealer or a qualified technician.
1. Remove the seat and rear shroud. See VII.
“Disassembly and Assembly.”
2. Disconnect the battery tie-down strap. See
figure 13C.
3. Disconnect the battery harness for each battery by pulling it straight up. See figure 13.
4. Disconnect the battery cables from the battery
terminals of each battery.
5. Remove the old batteries.
6. Place a new battery in each battery well. Face
the battery terminals toward the seat post.
7. Connect the red battery cable to the positive
(+) battery terminal. See figure 13A.
8. Connect the black battery cable to the negative (-) battery terminal on each battery.
9. Ensure the battery terminals are covered with
the tiller boots.
NOTE: See figure 13B for correct hardware
placement for battery terminal connections.
10. Reconnect the battery harness.
11. Reconnect the battery tie-down strap, making
sure the strap is positioned over the frame
release lever to ensure proper securement.
See figure 13C.
12. Reinstall the rear shroud and seat.
BATTERY
TERMINALS
UNDER
BOOTS
BATTERY
HARNESSES
Figure 13. Battery Harnesses and Battery Cables
+
BATTERY
+
BATTERY
Figure 13A. Battery Cable
Orientation
Figure 13B. Cable To Terminal Connection
NOTE: If you encounter a damaged or cracked
battery, immediately enclose it in a plastic bag
and contact your local waste disposal agency,
recycling center or your authorised Pride
Dealer for instructions on disposal and battery
recycling, which is our recommended course of
action.
26
www.pridemobility.com
Celebrity X Sport
IV. BATTERIES AND CHARGING
Why do my new batteries seem weak?
Deep-cycle batteries employ a different chemical
technology than that used in car batteries, nickel-cadmium batteries (nicads) and other common battery
types. Deep-cycle batteries are specifically designed
to provide power, drain down their charge and then
accept a relatively quick recharge.
We work closely with our battery manufacturer to
provide batteries that best suit your scooter’s specific
electrical demands. Fresh batteries are shipped fully
charged to our customers. During shipping, the batteries may encounter temperature extremes that can
influence their initial performance. Heat diminishes
the charge on the battery; cold slows the available
power and extends the time needed to recharge the
battery.
BATTERY TIE-DOWN STRAP
Figure 13C. Battery Tie-Down Strap
It may take a few days for the temperature of your scooter’s batteries to stabilise and adjust to their new
room or ambient temperature. More importantly, it takes a few charging cycles (partial draining followed
by full recharging) to establish the critical chemical balance that is essential to a deep-cycle battery’s peak
performance and long life.
Follow these steps to properly break in your scooter’s new batteries for maximum efficiency and service life.
1. Fully recharge any new battery prior to its initial use. This charging cycle brings the battery up to about
88% of its peak performance level.
2. Operate your new scooter in familiar and safe areas. Drive slowly at first and do not travel too far from
your home or familiar surroundings until you have become accustomed to your scooter’s controls and
have properly broken in your scooter’s batteries.
3. Fully recharge the batteries. They should be at over 90% of their peak performance level.
4. Operate your scooter again.
5. Fully recharge the batteries again.
6. After four or five charging cycles, the batteries are able to receive a charge of 100% of their peak
performance level and are able to last for an extended period of time.
What about public transport?
If you intend to use public transport with your scooter, you must contact the transportation dealer in
advance to determine their specific requirements.
Celebrity X Sport
www.pridemobility.com
27
V. OPERATION
BEFORE GETTING ONTO YOUR SCOOTER
Have you fully charged the batteries? See IV. “Batteries and Charging.”
Is the manual freewheel lever in the drive (rearward) position? Never leave the manual freewheel lever
pushed forward unless you are manually pushing your scooter.
Is the tiller lock knob in the unlocked position? See VII. “Disassembly And Assembly.”
GETTING ONTO YOUR SCOOTER
1. Make certain that the key is removed from the key switch.
WARNING! Never attempt to get onto or off of your scooter without first removing the key
from the key switch. This will prevent the scooter from moving if accidental throttle
control lever contact is made.
2.
3.
4.
5.
6.
7.
8.
Stand at the side of your scooter.
Disengage the seat rotation lever and rotate the seat until it is facing you.
Make certain that the seat is secured into position.
Position yourself comfortably and securely in the seat.
Disengage the seat rotation lever and rotate the seat until you are facing forward.
Make certain that the seat is secured into position.
Make certain that your feet are safely on the floorboard.
PRE-RIDE ADJUSTMENTS AND CHECKS
Is the seat at the proper height? See VI. “Comfort Adjustments.”
Is the seat positioned securely into place?
Is the tiller at a comfortable setting and locked securely in place? See VI. “Comfort Adjustments.”
Is the key fully inserted into the key switch and turned clockwise to the “on” position?
Does the scooter’s horn work properly?
Is your proposed path clear of people, pets and obstacles?
Have you planned your route to avoid adverse terrain and as many inclines as possible?
OPERATING YOUR SCOOTER
WARNING! The following can adversely affect steering and stability while operating your
scooter:
Holding onto or attaching a leash to walk your pet
Carrying passengers (including pets)
Hanging any article from the tiller
Towing or being pushed by another motorised vehicle
Keep both hands on the tiller and your feet on the floorboard at all times while operating your scooter. This
driving position gives you the most control over your vehicle.
Set the speed adjustment dial to your desired speed.
Push or pull the appropriate side of the throttle control lever.
The electromechanical disc park brake automatically disengages and the scooter accelerates smoothly
to the speed you preselected with the speed adjustment dial.
Pull on the left handgrip to steer your scooter to the left.
Pull on the right handgrip to steer your scooter to the right.
Move the tiller to the centre position to drive straight ahead.
To stop, slowly release the throttle control lever. The electronic brakes will automatically engage,
bringing your scooter to a stop.
28
www.pridemobility.com
Celebrity X Sport
V. OPERATION
NOTE: Your scooter’s reverse speed is slower than that of the forward speed you preset with the speed
adjustment dial.
GETTING OFF YOUR SCOOTER
1. Bring your scooter to a complete stop.
2. Remove the key from the key switch.
3. Disengage the seat rotation lever and rotate the seat until you are facing toward the side of your scooter.
4. Make certain that the seat is secured into position.
5. Carefully and safely get out of the seat and stand to the side of your scooter.
6. You can leave the seat facing to the side to facilitate boarding your scooter next time.
POWER DOWN TIMER FEATURE
Your scooter is equipped with an energy saving automatic power down timer feature designed to preserve
your scooter’s battery life. If you mistakenly leave the key in the key switch and in the “on” position but
do not use your scooter for approximately 20 minutes, the scooter’s controller shuts down automatically.
Although the controller is shut down, power will still be supplied to the scooter’s lighting system.
If the power down timer feature takes effect, perform the following steps to resume normal operation.
1. Remove the key from the key switch.
2. Reinsert the key and power up your scooter.
Celebrity X Sport
www.pridemobility.com
29
VI. COMFORT ADJUSTMENTS
After becoming familiar with your scooter’s operation,
you may find the need to make some adjustments to
increase your comfort.
WARNING! Remove the key from the
key switch before adjusting the tiller
or the seat. Never attempt to adjust
the tiller or the seat while the scooter
is in motion.
TILLER ANGLE ADJUSTMENT
Your scooter is equipped with an adjustable pivoting tiller.
1. While supporting the tiller, turn the tiller
adjustment knob anticlockwise to loosen the tiller.
See figure 14.
2. Move the tiller to a comfortable position.
3. Turn the tiller adjustment knob clockwise to secure
the tiller in position.
TILLER ADJUSTMENT
KNOB
Figure 14. Tiller Angle Adjustment
NOTE: In order to fully lower the tiller, you must first
remove the seat. Remove the seat by pulling it straight
up and off of the scooter.
ADJUSTMENT DIAL
ARMREST ANGLE ADJUSTMENT
The armrest angle of your scooter can be adjusted
upward or downward by turning the adjustment dial.
See figure 15.
NOTE: Pivot the armrests upward to make getting
onto and off of your scooter easier.
SEATBACK ANGLE ADJUSTMENT
Figure 15. Armrest Angle Adjustment
WARNING! Do not operate your scooter
with the seatback in a reclined position.
WARNING! Always keep your back
pressed firmly against the seatback
while adjusting the angle.
To adjust your scooter's reclining seat, perform
these steps.
1. With your back pressed up against the seatback, lift up
on the seatback adjustment lever (see figure 16) and
lean forward or rearward to adjust the seatback angle.
2. Release the seatback adjustment lever once the seat
is in a comfortable riding position.
SEATBACK
ADJUSTMENT
LEVER
Figure 16. Seatback Angle Adjustment
30
www.pridemobility.com
Celebrity X Sport
VI. COMFORT ADJUSTMENTS
SEAT ROTATION LEVER
SEAT ROTATION
The seat rotation lever will secure the seat into several positions.
1. Push forward on the seat rotation lever to release the seat. See figure 17.
2. Rotate the seat to the desired position.
3. Release the lever to secure the seat into place.
FRONT-TO-BACK SEAT ADJUSTMENT
You can reposition the seat forward or rearward to
adjust the distance between the seat and the tiller.
See figure 17.
1. Move the seat sliding lever outward.
2. While holding the lever out, slide the seat forward or rearward.
3. Release the seat sliding lever once the seat is in
the desired position.
SEAT HEIGHT ADJUSTMENT
The seat can be repositioned to different heights.
See figure 18.
1. Remove the seat and shroud from your scooter.
See VII. “Disassembly and Assembly.”
2. Remove the seat height adjustment bolt.
3. Loosen the clamp-action bolt.
4. Raise or lower the upper seat post to the desired
seat height.
5. While holding the upper seat post at that height,
match up the locating holes in the upper seat
post with those of the lower seat post.
6. Insert the seat height adjustment bolt through
the locating holes of both the upper and lower
seat posts.
7. Reinstall the nut onto the seat height adjustment bolt and tighten.
8. Tighten the clamp-action bolt.
9. Reinstall the rear shroud and the seat.
SEAT SLIDING LEVER
Figure 17. Seat Adjustment Levers
NUT
UPPER SEAT
POST
LOCATING
HOLES
NUT
SEAT HEIGHT
ADJUSTMENT
BOLT
CLAMP-ACTION
BOLT
LOWER SEAT POST
Figure 18. Seat Height Adjustment
Celebrity X Sport
www.pridemobility.com
31
V I . CO M F O R T A D J U S T M E N T S
MIRROR POSITION
To install the mirror (see figure 19):
1. Determine a side to install the mirror and remove the
rubber plug from the top of the tiller handle.
2. Insert the threaded end of the mirror holder into the
opening and rotate it clockwise until snug.
3. If necessary, rotate the nut clockwise to secure the
mirror in place.
MIRROR HOLDER
PLUG
NUT
To adjust the mirror:
1. Position yourself in a seated driving position facing
forward.
2. Adjust the mirror left, right, up or down until you have
a good line of sight behind you.
Figure 19. Mirror Installation
POSITIONING BELT (OPTIONAL)
Your scooter seat may be equipped with an auto-type
positioning belt that can be adjusted for operator comfort.
See figure 20. The positioning belt is designed to help support the operator so that he/she does not slide down or forward in the seat. The positioning belt is not designed for
use as a restraining device.
To install the positioning belt (if required):
1. Remove the seat from your scooter.
2. Place the seat upside down so that you can see the bottom of the seat base.
3. Remove the two bolts on the outermost part of the rear
seat mounting strap.
4. Insert the bolt through the appropriate end of the positioning belt and then through the seat mounting strap
for each side of the scooter seat.
5. Tighten the bolts.
Figure 20. Positioning Belt
To adjust the positioning belt for operator comfort:
1. Insert the metal tab on the right side of the belt into the plastic housing on the opposite strap until you
hear a “click.”
2. Pull the strap on the right side of the belt until it is secure, but not so tight as to cause discomfort.
MANDATORY! Make sure the positioning belt is properly secured to the scooter and is
adjusted for operator comfort.
MANDATORY! Inspect the positioning belt for loose or damaged parts before each use of
the scooter. If you discover a problem, contact your authorised Pride Dealer for
maintenance and repair.
32
www.pridemobility.com
Celebrity X Sport
VII. DISASSEMBLY AND ASSEMBLY
DISASSEMBLY
You can disassemble the scooter into seven
pieces: the seat, the front section, the rear
section, the rear shroud, the basket and the
batteries. See figure 21. No tools are required to
disassemble or assemble your scooter, but keep
in mind that the disassembled sections of the
scooter take up more floor space than the
assembled unit. Always disassemble or
assemble your scooter on a level, dry surface
with sufficient room for you to work and move
around your scooter—about 2 metres (5 feet) in
all directions. Remember that some scooter
components are heavy and you may need
assistance when lifting them.
WARNING! Avoid lifting weight
beyond your physical capability.
Ask
for
assistance
when
necessary while disassembling
or assembling your scooter.
REAR SECTION
REAR SHROUD
SEAT
BATTERIES
FRONT SECTION
BASKET
Figure 21. The Scooter Disassembled
1. Place the scooter in drive mode by engaging the freewheel lever.
2. Lock the tiller in the straight ahead position by pushing the tiller lock knob in and turning it clockwise
90°. See figure 22. The front wheel must face forward in order to lock the tiller.
3. Remove the seat by lifting it straight up and off of the scooter. If you encounter resistance when
removing the seat, disengage the seat rotation lever and swivel the seat back and forth while lifting up
on the seat.
UNLOCKED POSITION
LOCKED POSITION
Figure 22. Tiller Lock Knob (Locked)
Celebrity X Sport
Figure 22A. Tiller Lock Knob (Unlocked)
www.pridemobility.com
33
VII. DISASSEMBLY AND ASSEMBLY
4. Gently pull the rear shroud up and off of the
rear section of the scooter.
5. Unplug the front-to-rear and rear lighting
harnesses by squeezing the sides and pulling
straight up.
6. Unplug both battery harnesses. Pull each
harness straight up. See figure 23.
7. Unfasten the battery tie-down straps and
remove the batteries from the battery wells.
WARNING! Failure to unplug both
battery harnesses, the front-torear harness and rear lighting
harness prior to separating the
front and rear sections could
result in permanent damage to the
scooter.
Handbrake Cable Disconnect
1. Locate the quick disconnect body. See figure 24.
2. Pull the quick disconnect handle back from the
quick disconnect body.
3. Position the quick disconnect handle over the
top of the quick disconnect body.
4. Separate the brake cable from the cable clamp
located inside the quick disconnect body. See
figure 25.
REAR LIGHTING HARNESS
BATTERY HARNESSES
Figure 23. Harness Connections
QUICK DISCONNECT HANDLE
Frame Separation
1. Lift up on the frame release lever. See figure 26.
2. Lift the front section up until the frame hooks
of the front section separate from the rear section. See figure 27.
NOTE: Stabilise the rear section with your free
hand by holding onto the upper frame tube.
FRONT-TO REAR HARNESS
QUICK DISCONNECT BODY
Figure 24. Quick Disconnect Handbrake Cable
3. Slowly separate the two sections. See figure 27.
Figure 25. Handbrake Cable Release
34
www.pridemobility.com
Celebrity X Sport
VII. DISASSEMBLY AND ASSEMBLY
ASSEMBLY
1. Position the front and rear sections of your
scooter as shown in figure 27.
2. Use the frame release lever to lift the front section as you align the frame hooks of the front
section with the lower frame tube of the rear
section. See figure 27.
3. Once the frame hooks are over the lower frame
tube, lower the front section completely. This
will engage the frame lock. See figure 26.
4. Raise the tiller and fully tighten the tiller adjustment knob.
5. Reinstall both batteries and secure with the tiedown strap.
6. Connect the front-to-rear harness, rear lighting
harness and both battery harnesses. See figure 23.
7. Reinstall the rear shroud.
8. Reinstall the seat and rotate it until it locks into
place.
9. Unlock the front wheel by turning the tiller lock
knob 90° anticlockwise. See figure 22A.
FRAME RELEASE LEVER
FRAME HOOK
Figure 26. Frame Release
LOWER FRAME TUBE
UPPER FRAME TUBE
WARNING! After assembly, make
absolutely certain the tiller lock
knob is in the unlocked position
FRAME HOOK
Figure 27. Frame Separation
Celebrity X Sport
www.pridemobility.com
35
VIII. BASIC TROUBLESHOOTING
Any electromechanical device occasionally requires some troubleshooting. However, most of the
problems that may arise can usually be solved with a bit of thought and common sense. Many of these
problems occur because the batteries are not fully charged or because the batteries are worn down and can
no longer hold a charge.
DIAGNOSTIC FLASH CODES
The diagnostic flash codes for your scooter are designed to help you perform basic troubleshooting quickly
and easily. A diagnostic flash code will flash from the status LED in the event one of the conditions listed
below develops.
NOTE: Your scooter will not run unless the flash code condition is resolved and the scooter has been
turned off, then turned back on.
FLASH CODE
(1,1)
CONDITION
SOLUTION
Controller is hot; the scooter seems to be Shut down your scooter for a minumum
of several minutes to allow the controller
losing power.
to cool.
(1,4)
Battery charge is low.
Charge batteries as soon as possible.
Throttle pot fault.
Contact your authorised Pride Dealer
for assistance.
Contact your authorised Pride Dealer
for assistance.
(3,3)
(1,2)
(1,3)
Speed pot fault.
(1,5)
(3,5)
(3,4)
(3,2)
Attempting to operate the scooter with
the charger attached.
Turn the scooter key to the off
position. Switch off the charger and
remove the lead from the charger port,
then restart your scooter.
Throttle control lever not at centre
position at start up.
Return the throttle control lever to
centre position, turn scooter off, and
then back on.
The manual freewheel lever may be in the
freewheel (forward) position.
Turn the scooter key to the off
position. Push the freewheel lever to
the drive (rearward) position, then
restart your scooter.
A brake fault has occurred.
Contact your authorised Pride Dealer
for assistance.
What if all the systems on my scooter seem to be “dead”?
Make certain that the key is in the “on” position.
Check that the batteries are fully charged.
Push in the main circuit breaker reset button. See III. “Your Scooter.”
Make certain that both battery harnesses and the front-to-rear harness are firmly connected. See VII.
“Disassembly and Assembly.”
Be sure the power down timer feature hasn’t been activated. See V. “Operation.”
36
www.pridemobility.com
Celebrity X Sport
VIII. BASIC TROUBLESHOOTING
What if my scooter does not move when I engage the throttle control lever?
When the manual freewheel lever is pushed forward, the brakes are disengaged and all power to the
motor/transaxle assembly is cut.
Push rearward on the manual freewheel lever, turn the scooter off and then turn the scooter on to return
to normal scooter operation.
What if the main circuit breaker repeatedly trips?
If the main circuit breaker trips repeatedly, see your authorised Pride Dealer for service.
Charge the scooter’s batteries more frequently. See IV. “Batteries and Charging.”
If the problem continues, have both of your scooter’s batteries load tested by your authorised Pride
Dealer.
You may also perform the load test yourself. Battery load testers are available at most automotive parts
stores.
Follow the directions supplied with the load tester.
See IV. “Batteries and Charging” for information about your scooter’s battery type.
What if the battery condition meter dips way down and the motor surges or hesitates when I engage
the throttle control lever?
Fully charge your scooter’s batteries. See IV. “Batteries and Charging.”
Have your authorised Pride Dealer load test each battery.
Or, see the previous troubleshooting question for load testing the batteries yourself.
If you experience any problems with your scooter that you are not able to solve, immediately contact your
authorised Pride Dealer for information, maintenance and service.
Celebrity X Sport
www.pridemobility.com
37
IX. CARE AND MAINTENANCE
Your scooter requires a minimal amount of care and maintenance. If you do not feel confident in your
ability to perform the maintenance listed below, you may schedule inspection and maintenance at your
authorised Pride Dealer. The following areas require periodic inspection and/or care and maintenance.
TYRE PRESSURE
If equipped with pneumatic tyres, always maintain the psi/bar/kPa air pressure rating indicated on each tyre.
WARNING! It is critically important that the psi/bar/kPa air pressure rating be maintained
in pneumatic tyres at all times. Do not underinflate or overinflate your tyres. Low
pressure may result in loss of control and overinflated tyres may burst. Failure to
maintain the psi/bar/kPa air pressure rating indicated on pneumatic tyres at all times may
result in tyre and/or wheel failure.
Regularly inspect your scooter’s tyres for signs of wear.
EXTERIOR SURFACES
Bumpers, tyres and trim can benefit from an occasional application of rubber or vinyl conditioner.
WARNING! Do not use a rubber or vinyl conditioner on the scooter’s vinyl seat, floorboard
or tyre tread, as they will become dangerously slippery.
CLEANING AND DISINFECTION
Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your scooter.
Avoid using products that may scratch the surface of your scooter.
If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for
use on your product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or
cleaning agent before applying it to your product. Failure to comply may result in skin
irritation or premature deterioration of upholstery and/or scooter finishes.
ABS PLASTIC SHROUDS
The shrouds of the scooter are formed from durable ABS plastic and are coated with an advanced
formula urethane paint.
A light application of car wax will help the shrouds retain their high gloss.
HANDBRAKE
The handbrake lever may require periodic adjustment to maintain proper operation. Contact your authorised Pride Dealer for more information.
WIRING HARNESSES
Regularly check all wiring connections.
Regularly check all wiring insulation, including the charger power lead, for wear or damage.
Have your authorised Pride Dealer repair or replace any damaged connector, connection or insulation
that you find before using your scooter again.
PROHIBITED! Even though the scooter has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence. Check
electrical components frequently for signs of corrosion and replace as necessary.
38
www.pridemobility.com
Celebrity X Sport
IX. CARE AND MAINTENANCE
WHEEL REPLACEMENT
If your scooter is equipped with pneumatic tyres and
you have a flat tyre, you can have the tube replaced.
If your scooter is equipped with a solid tyre insert,
either the solid insert or the entire wheel must be
replaced depending on model. Contact your
authorised Pride Dealer for information regarding
replacement wheels for your scooter.
DRIVE
WHEEL
WASHER
AXLE KEY
WARNING! Wheels on your scooter
should only be serviced/replaced by
an authorised Pride Dealer or
qualified technician.
WARNING!
Completely
deflate
pneumatic tyres before dismantling
the rim or attempting repair.
WARNING! Be sure that the key is
removed from the key switch and the
scooter is not in freewheel mode
before performing this procedure.
WARNING! When changing a tyre,
remove only the centre lug nut, then
remove the wheel. If any further
disassembly is required, deflate the
tyre completely or it may explode.
DRIVE WHEEL NUT
Figure 28. Drive Wheel Removal
HUB
REAR RIM HALF
TYRE
Follow these easy steps for a quick and safe
repair of both pneumatic and solid tyres:
TUBE
1. Remove the key from the key switch.
2. Elevate the side of the scooter from which you
FRONT
are removing the tyre. Place wooden blocks
RIM HALF
under the frame to elevate the scooter.
WARNING! Completely deflate
3. If you are changing a pneumatic tyre, completely
the tyre before attempting repair!
deflate it before removing the wheel.
4. Remove the drive wheel nut and washer from the
WASHERS
axle. See figure 28.
NUTS
5. Pull the wheel off the axle.
6. Remove the nuts and washers and separate the Figure 29. Drive Wheel Assembly
rim halves. See figure 29.
7. Remove the old tube from the pneumatic tyre and replace it with a new tube or replace the entire
assembly if it is a solid tyre.
8. Reassemble the rim halves.
9. Slide the wheel back onto the axle. Make sure that the axle key is in the axle slot. See figure 28.
WARNING! Failure to ensure that the axle key is properly installed into the axle slot
when mounting the wheel can result in electronic brake failure, personal injury, and/or
product damage.
Celebrity X Sport
www.pridemobility.com
39
IX. CARE AND MAINTENANCE
10. Reinstall the drive wheel nut and washer onto the axle and tighten.
WARNING! Make sure both the nut and washer are reinstalled and tightened properly.
11. Inflate pneumatic tyres to the psi/bar/kPa air pressure rating indicated on each tyre.
12. Remove the block from beneath the scooter.
BATTERY TERMINAL CONNECTIONS
Make certain that the terminal connections remain tight and uncorroded.
The batteries must sit flat in the battery wells.
The battery terminals should face the rear of the scooter.
MOTOR BRUSHES
The motor brushes are housed inside of the motor transaxle/assembly. They should be inspected periodically for wear by your authorised Pride Dealer.
AXLE BEARINGS AND THE MOTOR/TRANSAXLE ASSEMBLY
You do not need to lubricate these items, as they are all prelubricated and sealed
CONSOLE, CHARGER AND ELECTRONIC CONTROLLER MODULE
Keep these areas away from moisture.
Before operating your scooter, allow any of these areas to dry thoroughly if they have been exposed to moisture.
NYLON LOCK NUT REPLACEMENT
Any nylon insert lock nut removed during the periodic maintenance, assembly or disassembly of the
scooter must be replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause
damage to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available
at local hardware stores or through your authorised Pride Dealer.
FUSES
To replace a fuse:
1. Remove the fuse by pulling it straight out of its slot.
2. Examine the fuse to be sure it is blown. See figures 30 and 30A.
3. Insert a new fuse of the proper rating.
WARNING! The replacement fuse must exactly match the rating of the fuse being
replaced. Failure to use properly rated fuses may cause damage to the electrical system.
Figure 30. Working Fuse
40
Figure 30A. Blown Fuse (Replace)
www.pridemobility.com
Celebrity X Sport
IX. CARE AND MAINTENANCE
STORING YOUR SCOOTER
If you plan on not using your scooter for an extended period of time, it is best to:
Fully charge its batteries prior to storage.
Disconnect both battery harnesses.
Store your scooter in a warm, dry environment.
Avoid storing your scooter where it will be exposed to temperature extremes.
WARNING! Always protect batteries from freezing temperatures and never charge a
frozen battery. Charging a frozen battery may result in damage to the battery.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures
or stored without a full charge may be permanently damaged, causing unreliable performance and limited
service life. It is recommended that you charge the scooter batteries periodically throughout periods of
prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your scooter to raise it off of the ground during
periods of prolonged storage. This takes the weight off the tyres and reduces the possibility of flat spots
developing on the areas of the tyres contacting the ground.
DISPOSAL OF YOUR SCOOTER
Your scooter must be disposed of according to applicable local and national statutory regulations. Contact
your local waste disposal agency or authorised Pride Dealer for information on proper disposal of packaging, metal frame components, plastic components, electronics and batteries.
Celebrity X Sport
www.pridemobility.com
41
X. WARRANTY
LIFETIME WARRANTY
Structural frame components, including: platform, fork, seat post and frame welds.
TWO-YEAR LIMITED WARRANTY
Drivetrain, including: transaxle, motor and brake.
ONE-YEAR LIMITED WARRANTY
All electrical parts, including controllers and battery chargers, are covered for one year under warranty.
Any attempt to open or dismantle these parts will lead to this warranty being void.
BATTERIES
Batteries are covered by a twelve-month warranty from the original manufacturer.
NOT COVERED UNDER WARRANTY
The following are classed as wear items, which may, under normal wear and tear, require replacing. These
items are not therefore covered under warranty: tyres, lap belts, bulbs, upholstery, plastic shrouds, motor
brushes and fuses. Warranty will also be refused if damage is deemed to have been caused through misuse
or accident for which Pride Mobility Products Ltd. cannot be deemed responsible.
NOTE: Pride Mobility Products Ltd. provides parts only under warranty. Your Pride Dealer is responsible for labour and service. Please contact your Pride Dealer for information about these services and
for any applicable charges.
42
www.pridemobility.com
Celebrity X Sport
APPENDIX - SPECIFICATIONS
Model Number
SCUK4401SP
Class of Use
B
Maximum Safe Slope
See figure1.
Maximum Climbing Ability
See figure 1.
Maximum Obstacle Climbing Ability
5 cm (2 in.)
Overall Length
118.75 cm (46.75 in.)
Overall Width
61 cm (24 in.)
Total Weight
87.54 kg (193 lbs.)
Total Weight Without Batteries
65.31 kg (144 lbs.)
Heaviest Piece When Disassembled
Front section: 29.02 kg (64 lbs.)
Turning
Radius2
144.80 (57 in.)
Speed (Maximum)1
Variable up to 12.87 km/h (8 mph)
Range Per Charge1,4
Up to 40.23 km (25 miles)
Ground Clearance2
8.26 cm (3.25 in.)
Weight Capacity
159 kg, 25 stone (350 lbs.)
Standard Seating
Type: CRS Deluxe
Weight: 16.78 kg (37 lbs.)
Material: Vinyl
Dimensions: 45.72 cm (18 in.) width
45.72 cm (18 in.) depth
68.58 cm (27 in.) height
Drive System
Rear-wheel drive, sealed transaxle, 24-volt DC motor
Dual Braking System
Regenerative and electromechanical
Tyres
Type: pneumatic
Front: 8.89 cm x 25.40 cm (3.5 in. x 10 in.)
Rear: 10.16 cm x 35.5 cm (4 in. x 13.9 in.)
Battery Requiements3
Two 12-volt, deep-cycle
Size: 40 Ah
Weight: 11.11 kg (24.50 lbs.) each
Battery Charger
Off-board
1
2
3
4
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery
condition, motors, controller type, tyre type, and tyre condition. This specification can be subject to a variance
of (+ or -) 10%.
Due to manufacturing tolerances and continued product improvement, this specification can be subject to
variance of (+ or – ) 3%.
AGM or Gel-Cell type required. See VI. “Batteries and Charging.”
Tested in accordance with ASNI/RESNA, WC Vol 2, Section 4 & ISO 7176-4 standards. Results derived from
theoretical calculation based on battery specifications and drive system performance. Test conducted at maximum weight capacity.
NOTE: This product conforms to all applicable ANSI-RESNA testing requirements and ISO 7176
EN12184 standards. All specifications subject to change without notice.
43
www.pridemobility.com
Celebrity X Sport
APPENDIX - SPECIFICATIONS
68.58 cm
(27")
123.19 cm - 133.35 cm
(48.5"-52.5")
43.18 cm - 53.34 cm
(17" -21")
8.26 cm (3.25")
118.75 cm (46.75")
45.72 cm
16"
(18")
45.72 cm
(18")
Turning Radius
144.80 cm (57")
61 cm (24")
Figure 31 Scooter Dimensions
44
www.pridemobility.com
Celebrity X Sport
NOTES
Celebrity X Sport
www.pridemobility.com
45
NOTES
46
www.pridemobility.com
Celebrity X Sport
CELEBRITY X SPORT
32 Wedgwood Road
Bicester, Oxon OX26 4UL
32 Wedgwood Road Bicester, Oxon OX26 4UL
*INFMANU3477*