Ventana 1200EAP Owner`s manual

VENTANA
Direct Vent ZC Fireplace
1200EAN (NG) & 1200EAP (LPG)
Installation & Owner’s Manual
!
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot
viewing glass is provided with this appliance and shall be
installed for the protection of children and other at-risk
individuals.
I N S TA L L E R
Leave this manual
with the appliance.
CONSUMER
Retain this manual
for future reference.
! WARNING
FIRE OR EXPLOSION HAZARD
Please read this manual BEFORE
installing and operating this appliance.
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
This appliance may be installed in an
after-market permanently located,
manufactured (mobile) home where not
prohibited by local codes.
This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with
other gases, unless a certified kit is used.
This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.
This appliance is suitable for installation in a
bedroom or bed sitting room.
Massachusetts: The piping and final
gas connection must be performed by a
licensed plumber or gas fitter in the State of
Massachusetts. Also, see Carbon Monoxide
Detector requirements on page 17.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
▪ Do not try to light any appliance.
▪ Do not touch any electrical switch; do
not use any phone in your building.
▪ Leave the building immediately.
▪ Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.
▪ If you cannot reach your gas supplier,
call the fire department.
— Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
4001272-30
©2015, Miles Industries Ltd. All rights reserved.
Ce guide est disponible en français sur demande.
Table of Contents
FOR THE QUALIFIED INSTALLER
Safety Precautions ................................................. 3
Safety and Your Fireplace ...................................... 4
Owner’s Information............................................... 5
Operating Your Fireplace for the First Time ............... 5
Cleaning Your Fireplace ............................................ 6
Checking Pilot and Burner Flames ............................ 8
Replacing Light Bulb.................................................. 8
Using Handset Wall Holder........................................ 8
Replacing Batteries ................................................... 8
Locating Lighting, Operation and
Rating Information Plate ......................................... 9
Servicing Your Fireplace ............................................ 9
Operating Your Fireplace ......................................... 10
How to Turn Your Fireplace OFF
(including pilot) ..................................................... 10
How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently ................................. 10
Remote Control Operation................................... 11
Options .................................................................. 15
Lighting Instructions ............................................ 16
Warranty ................................................................ 49
Commonwealth of Massachusetts...................... 17
Specifications ....................................................... 19
Overview................................................................ 20
Dimensions ........................................................... 21
Location................................................................. 21
Mantel Clearances ................................................ 22
Hearth Requirements ........................................... 24
Framing ................................................................. 27
Venting................................................................... 28
Co-axial Venting.................................................... 29
Co-Linear Venting ................................................. 33
Installation Planning ............................................ 34
Installation............................................................. 35
Unpack the appliance .............................................. 35
Fix the appliance to the floor ................................... 36
Remove Window ..................................................... 37
Connect Gas Supply................................................ 37
Install Liners ............................................................ 39
Install Ceramic Logs ................................................ 40
Refit and Check Window ......................................... 41
Synchronize Remote Control................................... 42
Install Electrical Components for
Decorative Lighting ............................................... 43
Check Operation...................................................... 44
Adjust Aeration (if necessary, NG units only) .......... 44
Install Window Skirt and Side Doors ....................... 44
Install Barrier Screen to the Appliance .................... 45
Install Handset Wall Holder ..................................... 45
Wiring Diagram ..................................................... 46
Approved Venting Components .......................... 47
Warranty ................................................................ 49
Spare Parts............................................................ 50
WA R
LOR
P
TY
R AN
M
GR A
RO
T
Warranty Card at the
back of this manual.
OR
The information contained in this installation
manual is believed to be correct at the time of
printing. Miles Industries Ltd. reserves the right
to change or modify any information or specifications without notice. Miles Industries Ltd.
grants no warranty, implied or stated, for the
installation or maintenance of your heater, and
assumes no responsibility for any consequential
damage(s).
VA
FOR THE OWNER
CO M F
Designed and Manufactured by / for
Miles Industries Ltd.
190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1
Tel. 604-984-3496 Fax 604-984-0246
www.valorfireplaces.com
2
© Copyright Miles Industries Ltd., 2015. All rights reserved.
!
Safety Precautions
READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW
these installation instructions may result in possible fire
hazard and will void the warranty.
Prior to the first firing of the fireplace, READ the
Owner’s Information section of this manual.
DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualified service technician
to inspect the unit and to replace any part of the control
system and any gas control that has been under water.
THIS UNIT IS NOT FOR USE WITH SOLID FUEL.
Installation and repair should be PERFORMED by a
qualified service person. The appliance and venting
system should be INSPECTED before initial use and at
least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.
Always KEEP the appliance clear and free from
combustible materials, gasoline, and other flammable
vapors and liquids.
NEVER OBSTRUCT the flow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.
This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent
system or components MAY BE USED.
This gas fireplace and vent assembly MUST be vented
directly to the outside and MUST NEVER be attached
to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate
vent system. Common vent systems are PROHIBITED.
INSPECT the external vent cap on a regular basis to
make sure that no debris, plants, trees, shrubs are
interfering with the air flow.
TURN OFF the gas before servicing this appliance.
It is recommended that a qualified service technician
perform an appliance check-up at the beginning of each
heating season.
DO NOT use this heater as a temporary source of heat
during construction.
State of California. Proposition 65 Warning. Fuels
used in gas, wood-burning or oil fired appliances,
and the products of combustion of such fuels, contain
chemicals known to the State of California to cause
cancer, birth defects and other reproductive harm.
California Health & Safety Code Sec. 25249.6.
Due to the high temperature, the appliance should be
LOCATED out of traffic areas and away from furniture
and draperies.
Clothing or flammable material SHOULD NOT BE
PLACED on or near the appliance.
This appliance is a DOMESTIC ROOM-HEATING APPLIANCE. It must not be used for any other purposes
such as drying clothes, etc.
DO NOT place furniture or any other combustible
household objects within 36” of the fireplace front.
BE CAREFUL not to put any decorating objects
sensitive to heat to close above or around the fireplace
as it gets very hot when operating.
The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.
DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualified
service person. DO NOT strike or slam the glass door.
The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the fireplace
manufacturer. NO SUBSTITUTE material may be used.
DO NOT USE abrasive cleaners on the glass door
assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.
A BARRIER DESIGNED TO REDUCE THE RISK OF
BURNS from the hot viewing glass is provided with
this appliance and SHALL BE INSTALLED for the
PROTECTION OF CHILDREN and other AT-RISK
INDIVIDUALS.
If the barrier becomes damaged, the barrier SHALL BE
REPLACED with the MANUFACTURER’S BARRIER
for this appliance.
Any safety screen, guard or barrier removed for servicing the appliance, MUST BE REPLACED prior to
operating the appliance.
Children and adults should be ALERTED to the hazards
of high surface temperature and should STAY AWAY to
avoid burns or clothing ignition.
YOUNG CHILDREN should be CAREFULLY
SUPERVISED when they are in the same room as the
appliance. Toddlers, young children and others may
be susceptible to ACCIDENTAL CONTACT BURNS.
A physical barrier is recommended if there are at-risk
individuals in the house. To restrict access to a fireplace
or stove, INSTALL AN ADJUSTABLE SAFETY GATE
to keep toddlers, young children and other at-risk
individuals out of the room and away from hot surfaces.
3
!
Safety and Your Fireplace
Safety and Your Fireplace
Please Read and Carefully Follow all Safety Warnings and
Operating Instructions Contained in Your Owner’s Manual
(Replacement Manuals are available by contacting our service department at
1-800-468-2567 or visit www.valorfireplaces.com).
Please Follow These Important
Child Safety Precautions and
Recommendations,
4
•
Parts of your Valor Fireplace become
extremely hot while in operation.
•
The glass viewing window
temperature can
exceed 500 F
at full capacity.
Momentary contact
with a hot glass
surface can cause
a severe burn, even if the fireplace
is operating at reduced heating
capacity.
withdraw in the event of accidental
contact with a hot surface.
•
A physical barrier is strongly
recommended if there are young
children, or at-risk individuals in the
house. Install an approved aftermarket safety gate to keep toddlers,
young children and other at-risk
individuals a safe distance from the
fireplace.
•
Keep the remote control handset
out of reach of children at all
times. A wall mount storage holster
is provided with your remote control
handset.
•
The glass window will remain hot
for an extended period of time after
the fireplace has been turned off.
Ensure that children are prevented
from touching the fireplace during the
cool down period.
•
Ensure that the fireplace, including
the pilot light, is completely turned
off when children are present and
close supervision and safety barriers
are not available—see pages 9–10 of
Owner’s Information section.
•
Toddlers and Young Children
must be closely supervised at all
times when they are in the same
room as the operating fireplace. They
lack full awareness of danger and
rely on your protection. Toddlers,
in particular, do not have the motor
skills and response reflexes to
•
If the fireplace is not going to be used
for the summer or any extended
period of time, remove the batteries
from the remote control handset
and receiver. It is recommended that
batteries are replaced annually in any
event—see page 8.
Owner’s Information
! WARNING
EXTREMELY HOT!!!
• READ the SAFETY information on pages
3 and 4 of this manual BEFORE operating
your gas heater.
• Some parts of your fireplace are EXTREMELY
HOT, particularly the GLASS window.
• DO NOT LET CHILDREN touch the glass or
any parts of your fireplace even after it is
turned off as it is still hot.
• USE THE BARRIER SCREEN provided with
the trim or a GATE to reduce the risk of severe
burns.
• Keep the remote control handset OUT OF
REACH of children.
• HOT WALL SURFACES! The wall directly above
the fireplace is VERY HOT when the fireplace
heats. It is constructed of non-combustible
materials and although safe, it may reach
temperatures in excess of 200º F depending
on choice of trims. DO NOT TOUCH IT!
• HOT HEARTH/FLOOR SURFACE! The
hearth or floor directly in front of the fireplace
is VERY HOT when the fireplace heats. Even
if constructed of non-combustible materials,
and although safe, it may reach temperatures
in excess of 200º F depending on choice of
materials. DO NOT STEP ON IT!
• Some materials or items, although safe, may
discolor, shrink, warp, crack, peel, and so on
because of the heat produced by the fireplace.
AVOID PLACING candles, paintings, photos,
and other items SENSITIVE TO HEAT within
36 inches (0.9 m) around the fireplace.
• Solid wood flooring in front of the fireplace (if
allowed) may shrink during the heating season
due to heat.
Performance of LPG appliances may be affected by
the quality of commercial gas supplied in your area.
OWNER’S
INFORMATION
Thank You ...
For purchasing a Valor by Miles Industries. Your new
radiant gas heater is a technical appliance that must
be installed by a qualified dealer. Each Valor fireplace
is fully tested during the production process for your
safety and comfort.
Your unit has been professionally installed by:
Dealer Name: ________________________________
Phone Number :_______________________________
Should you encounter an operational problem, call
your dealer immediately.
Do not try to repair the unit as you may cause an
injury or damage the fireplace.
This manual and particularly the preceeding
and following pages contain very important
information regarding the safe operation of your
fireplace as well as maintenance instructions.
Read carefully BEFORE operating your fireplace
and pay special attention to the SAFETY
WARNINGS.
A heating gas appliance does require safe handling
and for this reason, we very strongly recommend that
no children be allowed to touch the fireplace and its
controls at all times. Do install a screen or barrier
in front of the fireplace to protect your children
against severe burns.
Operating Your Fireplace for the First Time
When operating your new fireplace for the first time,
some vapors may be released due to the burning of
curing compounds used in the manufacture of the
appliance. They may cause a slight odor and could
cause the flames to be the full height of the firebox, or
even slightly higher, for the first few hours of operation.
It is also possible that these vapors could set off any
smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room. After
a few hours use, the vapors will have disappeared and
the flames will be at their normal height.
Flame Supervision Device
Fireplace
Hearth
Do not put
furniture or other objects
in this space in front of
the fireplace:
36” (0.9 m)
For your safety, this appliance is fitted with a flame
supervision device which will shut-off the gas supply
if, for any reason, the pilot flame goes out. This device
incorporates a fixed probe, which senses the heat
from the pilot flame. If the probe is cool, the device will
prevent any gas flow unless manually lighting the pilot.
See full lighting instructions on page 16 of this manual.
5
OWNER’S
INFORMATION
Owner’s Information
Cleaning Your Fireplace
! WARNING
DO NOT TOUCH THE GLASS WHILE IT IS HOT!
Let the fireplace cool first before cleaning it.
Important - Glass cleaning - Mineral deposits
One of the by-products of the combustion process in
a gas appliance is a mineral which can show up as a
white film on the ceramic glass of the viewing door.
The composition of the deposit varies widely from
various locations and also from time to time in the same
location. It seems this is associated with the varying
sulfur content of the gas. You may have the problem for
a time and then not see it for many months when it will
reappear in your area.
We have discussed this problem with ceramic glass
manufacturers and they cannot give us a definitive
answer to this problem. Dealers have tried various
cleaning products with varying results. The following
recommendations will not guarantee results in your
particular case.
NOTE: This is a problem beyond Miles Industries’
control and is not covered under warranty.
• Clean the glass regularly as soon as you notice
the buildup (white film). If the film is left for a longer
period of time, it will bake on. It is then much harder,
if not impossible, to remove.
• NEVER use an abrasive cleaner on the ceramic
glass. Any abrasion of the surface has the
immediate effect of compromising the strength
of the glass. An emulsion type cleaner is
recommended.
• Use a soft damp cloth to apply the cleaner. Dry the
glass with a soft, dry, preferably cotton cloth. Most
paper towels and synthetic materials are abrasive
to ceramic glass and should be avoided.
• Our dealers have had good results from the
products listed below. We cannot, however,
guarantee the results of these products.
• BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN CREME
by ELCO, WHITE OFF by RUTLAND, TURTLE WAX
Do not clean the glass while it is hot!
Always securely replace the window and the barrier
screen before lighting.
If broken, the glass pane may only be replaced
as a complete window unit as supplied by the
manufacturer.
If the barrier becomes damaged, the barrier shall
be replaced with the manufacturer’s barrier for this
appliance.
6
To have a access to the window for cleaning, you must
first remove the barrier screen.
! WARNING
WARNING
DO NOT TOUCH THE BARRIER SCREEN OR
FIREPLACE WHILE THEY ARE HOT! Let the
fireplace cool first before cleaning it.
To clean the barrier screen:
1. Push the screen upwards so that the lower serrated
tabs unhook from their brackets.
2. Unhook the top serrated tabs.
3. Clean the screen with a soft brush.
To clean the window and inside the firebox:
1. Find the levers on each side of the window towards
the top. Using your finger, pull the lever towards you
and unhook it from the window frame bracket.
Spring Loaded
Window Levers
2. Gently pull the top of the window outward.
3. Lift the window out of its bottom railing and set it
aside in a safe place to avoid damage.
4. Clean the window using the guidelines in this
section.
5. Dust the inside of the firebox including the ceramic
logs and walls with a soft brush. When cleaning,
make sure that no particles are brushed into the
slots of the burner.
OWNER’S
INFORMATION
Owner’s Information
To refit the window:
1. Place it in its bottom railing and push its top against
the firebox.
2. While you hold it, pull the side levers back into the
window brackets on each side.
3. Pull out the top of the window and release it to
insure the springs return it.
IMPORTANT: To ensure a safe operation, ensure that
the spring-loaded mechanism functions properly.
4. Apply light hand pressure against the window frame
sides to bed-in the window seal.
To reinstall the barrier screen:
! WARNING
FOR SAFETY PURPOSE, ensure the barrier
screen is re-installed on the fireplace front
after maintenance.
1. Hook the top tabs in the slots of the convection
baffle (a).
2. Push the screen up and hook the bottom serrated
tabs to the brackets at the bottom of the fireplace
opening (b).
5. If the Hot Glass Warning plate has been removed
from the front lower corner of the window,
reinstall it by sliding it between the glass and
the frame as indicated.
a
Hot Glass Warning Plate
a
b
b
7
OWNER’S
INFORMATION
Owner’s Information
Checking Pilot and Burner Flames
A periodic check of the pilot and burner flames should
be made. Check after the fire has been on for at least
30 minutes. The pilot flame must cover the tip of the
thermocouple probe. The main burner flame pattern will
vary from appliance to appliance depending on the type
of installation and climatic conditions.
3. While holding the glass cover so it does not fall and
shatter, swivel one or both of its retaining tabs to
free the glass. Gently remove the glass cover.
Light fixture without glass cover
4. Remove the light bulb from its socket by pushing
towards one end.
5. With a gloved hand, replace with a new light bulb
using only a 100 watts halogen 130 volts (type J
T3, 119 mm long).
Correct Flame Picture
Pilot Flame can be seen between logs
100W Halogen Light Bulb (119mm)
Thermocouple
Probe must be in
Flame
Pilot Flame
The appliance area must always be kept clear and
free from combustible materials, gasoline and other
flammable vapors and liquids.
Inspect the vent terminal outdoors regularly to make
sure that snow, trees, bushes, leaves, or other objects
do not obstruct it.
Examine the vent system and terminal regularly. We
recommend annually.
Replacing Light Bulb
The appliance is equipped with a decorative light inside the firebox located in front
of the window. To replace the light bulb,
follow these steps:
1. Turn off the decorative light wall switch.
2. Locate the light fixture. Loosen the screws of the
glass cover retaining tabs.
Tab
Light fixture with glass cover
Tab
6. Test the bulb by turning the wall switch on. Turn
the switch off again to complete the operation.
NOTE: If the bulb is new and not functioning, turn
off the dimmer switch and call your local electrician
for inspection.
7. Put the glass cover back in place and, while
holding it, turn the retaining tab(s) to retain
the glass.
8. Tighten the tabs’ screws.
Using Handset Wall Holder
Your fireplace equipment includes a wall
holder to store the handset. If it hasn’t be
installed, refer to the instructions further
on in this manual for the installation.
Replacing Batteries
! WARNING
DO NOT ATTEMPT TO CHANGE THE BATTERIES WHILE THE FIREPLACE IS STILL HOT! Let
the fireplace cool first before touching it.
CAUTION
DO NOT USE a screwdriver or other metallic
object to remove the batteries from the receiver or
the handset! This could cause a short circuit to the
receiver.
Low battery signal: see page 15.
BEFORE changing the batteries, turn off the valve
using the manual On/Off switch—see instructions
next page.
8
OWNER’S
INFORMATION
Owner’s Information
The appliance uses four 1.5 V AA alkaline batteries
for its remote control receiver and one 9 V alkaline
battery for its handset. Batteries should last one to two
seasons, depending on usage. Removing the batteries
in the off-season will extend the battery life. Should
the batteries lose power, the control may be operated
by manually turning the control knob at the valve or by
turning off the valve at the switch.
If the antenna was
unhooked when
replacing batteries,
hook it back to its
clip.
NOTE: It MUST
NOT TOUCH the
ignition wire!
Antenna
!
Ignition Wire
Locating Lighting, Operation and Rating
! WARNING
DO NOT ATTEMPT TO TOUCH THE DATA PLATE
WHILE THE FIREPLACE IS STILL HOT! Let the
fireplace cool first before touching it.
Information Plate
The Lighting, Operation and
Rating information is located
on a plate at the right hand
side of the firebox behind the
side door.
To access the plate, open
the right hand side door and
grab the plate and slide it out
to read it. There is important
information on both sides of
the plate.
The data plate is
located on the right of
the firebox behind the
side door.
Servicing Your Fireplace
If any attention is required for your appliance, contact
your supplier quoting the model number. It will be
helpful if the appliance serial number can also be
quoted. This number is on the rating plate, which is
located on the right hand side of the firebox behind
the side door. Open the side door and slide the plate
out. The replacement parts are shown at the end of
this manual. Please always quote the part number and
description when requesting spare parts.
CAUTION
To avoid short-circuit to the receiver, position the antenna so that it DOES NOT TOUCH the ignition wire.
To replace the batteries in the remote control
receiver:
1. Open the side panel to the left of the window.
2. The receiver is located under the valve and it is
retained to its platform by a Velcro tab. Grab the
receiver and pull it out from it’s platform.
3. Slide and remove the receiver cover.
4. Replace the batteries with 4 AA alkaline batteries.
5. Replace the cover.
6. Put the receiver back on its platform pushing it in
so it attaches to the Velcro tab. If it was unhooked,
replace the antenna in its clip.
IMPORTANT: The antenna MUST NOT TOUCH
the ignition wire to avoid a short-circuit.
9
OWNER’S
INFORMATION
Owner’s Information
Operating Your Fireplace
There are three ways to control your fireplace.
1. Thermostatic Remote Control;
2. Wall Switch;
3. Manual On/Off Switch.
The manual On/Off switch must be ON for the fireplace
to function. It can be used to shut off the fireplace in
case of emergency—see next section.
The Thermostatic Remote Control can be programmed
to function automatically—see pages 11–15.
How to Ensure Your Fireplace Cannot
Be Turned ON Inadvertently
You can use one of the two following methods to
ensure that your fireplace will not turn on when you
don’t want it on.
First, ensure your fireplace is turned off—including
the pilot—and cold BEFORE going ahead.
• You can prevent your fireplace from lighting by
pressing the O button on the manual ON/OFF
switch on the gas valve.
The Wall Switch (optional) can be used to turn on, off
and to increase or decrease the flame height—see
1265WSK—Wall Switch Kit.
NOTE: The remote control in the AUTO mode will
override the wall switch.
X
The receiver and gas
valve are located on
the left of the firebox
behind the side door.
Thermostatic Remote
Control
Wall Switch
(optional)
Manual On/Off Switch
How to Turn Your Fireplace OFF
(including pilot)
Familiarize yourself with each of these methods before
operating your fireplace.
Press and hold the OFF button for a second (either on
the handset or the wall switch).
If the flames are on, they go down and you hear the
valve motor wind down. You hear a clunk and a beep
indicating that the valve has received the signal from
the remote control.
ON
OFF
Manual ON/OFF Switch
• Alternately, remove all batteries from the receiver as
well as the battery from the handset.
Automatic Shut-Off (in certain conditions)
Your fireplace’s remote control is equipped with an
automatic shut-off mechanism which is activated in
certain conditions. See page 15 in the Remote Control
Operation section for a description of this feature.
Remote control
handset
10
Wall Switch
OWNER’S
INFORMATION
Remote Control Operation
NOTE: Before using the remote control system for
the first time, the receiver and the handset must be
synchronized. See the section Remote Control Initial
Set-up on page 42 of this manual.
Current
temperature
(F or C)
IMPORTANT: BEFORE YOU BEGIN, please note that
on this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when
the function display is flashing. Be patient when
programming as it can take a few seconds to set.
Handset
sensor
Period
start or end
(Temp, Timer)
Battery status
Current time
(12 or 24 hour clock)
Current
programmed
period (Timer)
Modes (Manual,
Temperature, Timer)
Display Overview
Note: In the TEMP or TIMER modes, the remote
handset senses the room temperature and adjusts the
flame accordingly.
To communicate, the handset should be within 15 feet
(4.5 meters) of the fireplace.
Do not leave the handset on the mantel or hearth.
TO TURN ON APPLIANCE
CAUTION
When pilot ignition is confirmed, motor turns
automatically to maximum flame height.
Large flame
button (flames
up, sets hours,
temperature)
Set (scrolls
through
modes and
settings)
OFF (returns
to set mode,
turns the burner
and the pilot off )
Small flame
button (flames
down and off,
sets minutes,
temperature)
Handset Overview
TO TURN OFF APPLIANCE
•
When the pilot is off, it will take 2
When the
pilotitiscan
off, be
it will
take 2
minutes
before
lit again.
minutes before it can be lit again.
• On the valve, turn MAN knob on the ON, full
counterclockwise
position.
• Place ON/OFF switch (if equipped) in I (ON
position).
•
Simultaneously press the OFF and
(large flame) buttons until a short
beep confirms the start sequence
has begun; release buttons.
• Continuing beeps confirm the
ignition is in process.
• Once pilot ignition is confirmed,
there is main gas flow.
• After main burner ignition the
handset will automatically go into
manual (MAN) mode.
Press OFF button.
STANDBY MODE (Pilot Flame)
• Press and hold
(small flame) to set appliance at
pilot flame.
FLAME HEIGHT ADJUSTMENT
•
In standby mode: Press and hold
(large flame) button to increase
flame height.
11
OWNER’S
INFORMATION
Remote Control Operation
• Press and hold
(small flame)
button to decrease flame height or
to set the appliance at pilot flame.
• For fine adjustment tap the
(large flame) or (small flame)
buttons.
MODES OF OPERATION
•
Briefly pressing the SET button
changes the mode of operation in
the following order:
MAN
→
Express Low and High Fire
• Double-click
(small flame)
button. “LO” will be displayed.
NOTE: Flame goes to high fire first
before going to designated low fire.
→
TIMER
TEMP
→
TEMP
→ and back to
MAN
.
NOTE: Manual mode can also be reached by pressing
either the
(large flame) or the (small
flame) buttons.
•
- Manual Mode - Manual
Flame Height Adjustment.
•
- Daytime Temperature Mode (Appliance must be in
standby mode; pilot ignited) - The
room temperature is measured and
compared to the set temperature.
The flame height is then automatically adjusted to achieve the
Daytime Set Temperature.
•
- Nighttime Setback
Temperature Mode (Appliance
must be in standby mode; pilot
ignited) - The room temperature
is measured and compared to the
Nighttime Setback temperature.
The flame height is then automatically adjusted to achieve the Nighttime Setback Temperature.
•
- Timer Mode (Appliance
must be in standby mode; pilot
ignited) - The timers P1 and P2
(Program 1, Program 2) each can
be programmed to go ON and OFF
at specific times. For instructions
see Timer Programming Mode.
MAN
x2
• Double-click
(large flame)
button. Flame automatically goes
to high fire. “HI” will be displayed.
x2
SETTING ºC/24-HOUR OR ºF/12-HOUR CLOCK
• In MAN mode, press OFF and
(small flame) buttons until display
changes from Farenheit/12-hour
clock to Celsius/24-hour clock and
vice versa.
SETTING THE TIME
• The time display will flash after
either:
• Installing the battery or
• Simultaneously pressing the
(large flame) and
(small flame)
buttons.
• Press
(large flame) button to
set the hour.
• Press
(small flame) button to
set the minute.
• Press OFF or simply wait to return
to MAN mode.
12
TEMP
TEMP
TIMER
NOTE: The display shows the set temperature every
30 seconds.
OWNER’S
INFORMATION
Remote Control Operation
SETTING THE ON / OFF TEMPERATURES
SETTING THE “DAYTIME” TEMPERATURE
SETTING THE “NIGHTTIME SETBACK” TEMPERATURE
Default Settings:
Default Settings:
•
TEMP
(sun), 23ºC / 74ºF
Briefly press SET button to scroll to
TEMP
TEMP
(sun) mode. Hold
the SET button until the TEMP
flashes.
TEMP
(moon), “--” (OFF)
• Briefly press SET button to scroll to
TEMP T E M P (moon) mode. Hold
the SET button until the TEMP
flashes.
• Press
(large flame) button
to increase the
Daytime Set
Temperature.
• Press
(large flame) button to
increase
Nighttime Setback
Temperature.
• Press
(small flame) button
to decrease
Daytime Set
Temperature.
• Press
(small flame) button to
decrease
Nighttime Setback
Temperature.
• Press OFF or simply wait to
complete programming.
• Press OFF or simply wait to
complete programming.
Tip
Set the different parameters when they are flashing.
13
OWNER’S
INFORMATION
Remote Control Operation
SETTING PROGRAM TIMERS
SETTING P1 OFF TIME
• You can program two periods of time between 12:00
am and 11:50 pm in each 24-hour cycle.
• The Programs P1 and P2 must be set in the
following order during a 24-hour cycle: P1 , P1 ,
P2
and P2 .
• The icon
indicates the beginning of the period (ON)
and the icon indicates the end of the period (OFF).
• If P1 = P1 or P2
= P2 , the programming
is cancelled.
• To keep the fireplace ON all night, set P2 at
11:50 am and P1
at 12:00 am.
•
Briefly press SET button to scroll
to TIMER P1 (moon) while the
time flashes.
•
Press
(large flame) button to set
the hour.
•
Press
(small flame) button to
set the minutes.
Default settings:
Program 1: P1
Program 2: P2
6:00 am P1
11:50 pm P2
8:00 am
11:50 pm
• Briefly press SET button to scroll to
TIMER mode.
SETTING P1 ON TIME
• Hold the SET button until P1
(sun) is displayed and the time
flashes.
• Press
(large flame) button to
set the hour.
• Press
(small flame) button to
set the minutes.
14
SETTING P2 ON TIME
• Briefly press SET to scroll to TIMER mode P2
(sun) while the time flashes.
• Follow the instructions given to set P1 ON time.
SETTING P2 OFF TIME
• Briefly press SET to scroll to TIMER mode P2
(moon) while the time flashes.
• Follow the instructions given to set P1 OFF time.
Press OFF button to save these settings. The timers
are programmed. See the diagram on programming
sequences on the following page.
Tip
If you want to program only one period, program P1
and P1 with desired times and program P2
and
P2
with the same time as P1 .
OWNER’S
INFORMATION
Remote Control Operation
Timer Programming Example (default temperatures shown)
6:00 a.m.—
P1
Start time
☼
Set temp
4:00 p.m.—
P2
Start time
8:00 a.m.—
P1 ☽
End time
☼
74˚F
Set temp
10:00 p.m.—
P2 ☽
End time
☼
☽
40˚F
AUTOMATIC TURN DOWN
Set temp
☼
74˚F
Set temp
6:00 a.m.—
P1
Start time
☼
☽
40˚F
LOW BATTERY INDICATION
• No communication. If there is no communication
between the receiver and the handset for a period of
6 hours, the appliance goes into pilot mode.
• No change in flame height. If there is no change
in flame height for a period of 6 hours, the appliance
goes into pilot mode.
NOTE: In TEMP or TIMER modes, the flame height
will vary according to room temperature. The appliance will continue to work normally. However, if the
room temperature remains the same for 6 hours, the
appliance will go into pilot mode.
AUTOMATIC SHUT OFF
• Low batteries in the receiver. With low battery
power in the receiver the system shuts off
completely.
NOTE: This does not apply when the power supply
is interrupted.
• No change in pilot. The appliance shuts off
completely when it is continually in pilot position—
without any change—for a period of 5 days.
CAUTION
DO NOT USE a screwdriver or other metallic object
to remove the batteries from the battery box or the
handset! This could cause a short circuit.
Remote handset: The battery icon
will show
when the battery needs to be replaced.
Replace with one 9 V alkaline battery.
Receiver: Three short ‘beeps’ will sound when the
motor turns when the batteries need to be replaced.
Replace with four 1.5 V alkaline batteries.
HANDSET / RECEIVER MATCH
The remote control handset and receiver are programmed to function together. In case of a replacement of
the handset or the receiver, you will need to reset the
receiver to allow them to function together. Contact your
dealer for details.
Options
Required Kits*
Ceramic Liners
1245VRL—Victorian Red Liner Pack
1250FSL—Frontera Liner Pack
1255IBL—Inca Slab Liner Pack
1260BSL—Black Slab Liner Pack
Optional Accessories*
Doors and Surrounds
1210DKA—Alhambra Door Kit
1215FDV—FenderFire Double Door Kit
1220FSV—FenderFire Single Door Kit
1240BPK—3-Sided Backing Plate Kit
1241FBK—4-Sided Backing Plate Kit
1235MTP—3-Sided Polished Trim
1237MFP—4-Sided Polished Trim
614CVI—Arched Cast Surround
615CVI—Cast Surround
Fret and Andirons
1225VFB—Ventana Fret Black
1230ACB—Andiron Classic Black
1236MAP—Metropolis Andiron Polished
Conversion Kit
1200PCK—Conversion Kit to Propane Gas
1200NCK—Conversion Kit to Natural Gas
Wall Switch
1265WSK—Wall Switch Kit
Fan
1270RBK—Remote Blower Kit
Hearth Gate
Hearth gates such as Cardinal VersaGates are
available at retail stores carrying safety products
for children.
*Information accurate at the time of printing and subject to
change without notice.
15
OWNER’S
INFORMATION
Lighting Instructions
FOR YOUR SAFETY, READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactlyD¿UHRUH[SORVLRQPD\UHVXOWFDXVLQJ
SURSHUW\GDPDJHSHUVRQDOLQMXU\RUORVVRIOLIH
A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly. To
save gas, turn the pilot off when not using the appliance for a prolonged period of time.
%%()25(/,*+7,1*VPHOODOODURXQGWKHDSSOLDQFHDUHDIRUJDV%HVXUHWRVPHOOQH[WWRWKHÁRRUEHFDXVHVRPHJDV
DUHKHDYLHUWKDQDLUDQGZLOOVHWWOHRQWKHÁRRr.
WHAT TO DO IF YOU SMELL GAS
‡'RQRWWU\WROLJKWDQ\DSSOLDQFH
‡'RQRWWRXFKDQ\HOHFWULFVZLWFKGRQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ
‡,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPDQHLJKERr’s phone. Follow the gas supplier’s instructions.
‡,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHrFDOOWKHÀUHGHSDUWPHQW
C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by hand,
GRQ·WWU\WRUHSDLUWKHPFDOODTXDOLÀHGVHUYLFHWHFKQLFLDQ)RUFHRUDWWHPSWHGUHSDLUPD\UHVXOWLQDÀUHRUH[SORVLRQ
D. Do not use this appliance if any part has been under water,PPHGLDWHO\FDOODTXDOLÀHGVHUYLce technician to inspect
the appliance and to replace any part of the control system and any gas control, which has been under water.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above. Dependent on model, switch #1 may be mounted directly to valve see Fig 2A.
)LJ
)LJ
)LJ$
2. SET ON/OFF SWITCH (1) TO “OFF” POSITION.
‡ WDLWÀYHPLQXWHVWRFOHDURXWDQ\JDVWKHQVPHOOIRUJDVLQFOXGLQJQHDUWKHÁRRr. If you smell gas, STOP! Follow
“B” in the safety information above on this label. If you don’t smell gas, go to the next step.
3. AUTOMA7,&,*1,7,21ÀJ/RFDWHWKHSLORWÀJLQVLGHRIÀUHER[DW/HIW+DQGVLGH
‡ 212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ21SRVLWLRQVHW)ODPH Adjustment knob (3) to lowest setting
(3);
‡ On the remote control handset, press and hold the ‘off ’ button and
(large flame) VLPXOWDQHRXVO\DVKRUW
DFRXVWLFVLJQDOFRQÀUPVWKHVWDUWKDVEHJXQ
‡ )XUWKHUVKRUWDFRXVWLFVLJQDOVLQGLFDWHWKHLJQLWLRQSURFHVVLVLQSURJUHVV
‡ When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.
‡ Press the (small flame)RQWKHUHPRWHFRQWUROKDQGVHWWRUHGXFHWKHÁDPHKHLJKW
4. MANUAL,*1,7,21ÀJWLWKWKHZLQGRZRIIORFDWHWKHSLORWÀJ
LQVLGHRIÀUHER[DW/HIW+DQGVLGH
‡ 212))VZLWFKLQ21SRVLWLRQ0$1NQRELQ0$1SRVLWLRQ
‡ Set Flame Adjustment knob (3) to the lowest setting (3);
)LJ
‡ 3XVKGRZQWKHPHWDOOLFFRUHZLWKDSHQRUVLPLODULQVWUXPHQWWKLVZLOOHVWDEOLVKWKHSLORWJDVÁRZ
/LJKWJDVDWWKHSLORWZLWKDPDWFK
&RQWLQXHKROGLQJGRZQPHWDOFRUHIRUDERXWVHFRQGVDIWHUUHOHDVHSLORWVKRXOGUHPDLQOLW
‡
If the pilot will not stay lit after several tries, turn the gas control knob (3) to “OFF” (3) and call your local
service technician or gas supplier.
5HLQVWDOOWKHZLQGRZDQGVHWWKH0$1NQREWR´21µWXUQ)ODPH Adjustment knob (3) up (4) or down
manually or use the up/down ‘flame’ buttons on the remote control handset to adjust theÁDPHKHLJKW
TO TURN OFF GAS TO APPLIANCE
1. AUTOMATIC SHUT2))XVLQJWKHUHPRWHFRQWUROKDQGVHW
X
‡ Press and hold the
(small flame) RQWKHUHPRWHFRQWUROKDQGVHWWRVKXWRIIWKHPDLQEXUQHUJDVÁRZ
‡ 3UHVV´2))µEXWWRQRQUHPRWHKDQGVHWWRVKXWRIIWKHDSSOLDQFHLQFOXGLQJSLORWÁDPH
2. MANUAL SHUT-OFF (using only the ON/OFF switch (1))
‡ Press “O” the ON/OFF switch (1) to shut-off the appliance.
16
Commonwealth of Massachusetts
State of Massachusetts Carbon Monoxide
Detector/Vent Terminal Signage
Requirements
For all side wall horizontally vented gas fueled
equipment installed in every dwelling, building or
structure used in whole or in part for residential
purposes, including those owned or operated by the
Commonwealth and where the side wall exhaust
vent termination is less than seven (7) feet above
finished grade in the area of the venting, including
but not limited to decks and porches, the following
requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE
DETECTORS. At the time of installation of the side wall
horizontal vented gas fueled equipment, the installing
plumber or gas fitter shall observe that a hard wired
carbon monoxide detector with an alarm and battery
back-up is installed on the floor level where the gas
equipment is to be installed. In addition, the installing
plumber or gas fitter shall observe that a battery
operated or hard wired carbon monoxide detector
with an alarm is installed on each additional level of
the dwelling, building or structure served by the side
wall horizontal vented gas fueled equipment. It shall
be the responsibility of the property owner to secure
the services of qualified licensed professionals for the
installation of hard wired carbon monoxide detectors.
a. In the event that the side wall horizontally vented
gas fueled equipment is installed in a crawl space or
an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next
adjacent floor level.
b. In the event that the requirements of this subdivision
can not be met at the time of completion of installation,
the owner shall have a period of thirty (30) days
to comply with the above requirements; provided,
however, that during said thirty (30) day period, a
battery operated carbon monoxide detector with an
alarm shall be installed.
OWNER’S
INFORMATION
3. SIGNAGE. A metal or plastic identification plate
shall be permanently mounted to the exterior of the
building at a minimum height of eight (8) feet above
grade directly in line with the exhaust vent terminal for
the horizontally vented gas fueled heating appliance
or equipment. The sign shall read, in print size no less
than one-half (1/2) inch in size, “GAS VENT DIRECTLY
BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of
the side wall horizontally vented gas fueled equipment
shall not approve the installation unless, upon
inspection, the inspector observes carbon monoxide
detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt
from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled
“Equipment Not Required To Be Vented” in the most
current edition of NFPA 54 as adopted by the Board;
and
2. Product Approved side wall horizontally vented
gas fueled equipment installed in a room or structure
separate from the dwelling, building or structure used in
whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM PROVIDED.
When the manufacturer of Product Approved side
wall horizontally vented gas equipment provides a
venting system design or venting system components
with the equipment, the instructions provided by the
manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting
system design or the venting system components; and
2. A complete parts list for the venting system design or
venting system.
2. APPROVED CARBON MONOXIDE DETECTORS.
Each carbon monoxide detector as required in
accordance with the above provisions shall comply
with NFPA 720 and be ANSI/UL 2034 listed and IAS
certified.
17
OWNER’S
INFORMATION
Commonwealth of Massachusetts
(d) MANUFACTURER REQUIREMENTS - GAS
EQUIPMENT VENTING SYSTEM NOT PROVIDED.
When the manufacturer of a Product Approved side
wall horizontally vented gas fueled equipment does
not provide the parts for venting the flue gases, but
identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions
shall be included with the appliance or equipment
installation instructions; and
2. The “special venting systems” shall be Product
Approved by the Board, and the instructions for that
system shall include a parts list and detailed installation
instructions.
(e) A copy of all installation instructions for all Product
Approved side wall horizontally vented gas fueled
equipment, all venting instructions, all parts lists
for venting instructions, and/or all venting design
instructions shall remain with the appliance or
equipment at the completion of the installation.
18
Specifications
Approval & Codes
This appliance is certified to ANSI Z21.88-2014/
CSA 2.33-2014 American National Standard / CSA
Standard for Vented Gas Fireplace Heaters for use in
Canada and USA, and to CGA 2.17-91 High Altitude
Standard in Canada. This appliance is for direct vent
installations.
This appliance complies with CSA P4.1-09 Testing
method for measuring annual fireplace efficiencies.
The installation must conform to local codes or, in
the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1 or the Natural Gas and
Propane Installation Code CAN/CGA-B149. Only
qualified licensed or trained personnel should
install this appliance.
QUALIFIED
INSTALLER
For installations at elevations above 4,500 feet
(1,370 m) in Canada, please consult provincial
and/or local authorities having jurisdiction.
Supply Gas
Heater engine 1200EAN is used with natural gas.
Heater engine 1200EAP is used with propane gas.
The supply pressure must be between the limits
shown in the Ratings section above.
X
This appliance must be electrically grounded in
accordance with local codes, or, in the absence of
local codes, with the National Electrical Code, ANSI/
NFPA 70 or the Canadian Electrical Code, CSA C22.1.
The supply connection is 3/8 inch NPT male and
located on the left hand side of the firebox. A shut-off
valve (not supplied) is required on the supply line to
isolate the unit during service.
Ratings
Conversion Kits
Model
Gas
Altitude (Ft.)*
Input Maximum (Btu/h)
Input Minimum (Btu/h)
Manifold Pressure (in w.c.)
Minimum Supply Pressure
(in w.c.)
Maximum Supply Pressure
(in w.c.)
Main Burner Injector
Marking
Pilot Injector Marking
Min. Rate By-Pass Screw
N
P
Natural
Propane
0-4,500 feet*
36,000
31,000
15,000
15,000
3.6”
10.5”
5”
11”
10”
14”
Cat #
82-1200
#51
#190
Cat #
92-360
#30
#125
The 1200 Ventana is supplied as natural gas or
propane gas and is field convertible between fuels.
See instructions packaged with the conversion kit
for further information.
Electrical
The 1200 does not require an electrical power source
to operate as a heater. However, it requires electrical
power to operate its decorative hearth light.
*High Altitude Installations
Input ratings are shown in BTU per hour and are
certified without deration for elevations up to 4,500
feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA,
installations must be in accordance with the current
ANSI Z223.1 and/or local codes having jurisdiction.
Heating value of gas in some areas is reduced to
compensate for elevation—consult your local gas
utility to confirm.
19
QUALIFIED
INSTALLER
Overview
Mantel—See Mantel Clearances
Fire On/Off
Wall Switch
(optional)
Framing—See Framing
Remote
Handset
Wall Holder
Cement Board—Combustible
wall finish may butt up to but
not cover cement board
Decorative Light
Dimmer Switch
(not provided)
Optional Doors and
Plates—see Options
Wall Finish
butted up to the
edge of door plate
1200EA
Barrier Screen to
prevent touching
the hot glass
Non-combustible Hearth—
See Hearth Requirements
Combustible Floor
! WARNING
Some materials or items, although safe,
may discolor, shrink, warp, crack, peel, and
so on because of the heat produced by the
fireplace. Avoid placing candles, paintings,
photos, and other items sensitive to heat
around the fireplace.
20
1/2” Insulation Board
When the appliance is installed directly on
carpeting, tile or other combustible material
other than wood flooring, the appliance shall
be installed on a metal or wood panel extending the full width and depth of the appliance
! WARNING
HOT HEARTH / FLOOR! The hearth or floor
in front of the fireplace may become very
hot when the fireplace heats. Do not use the
hearth as a seat or shelf. Solid wood flooring
in front of the fireplace (if allowed) may
shrink during the heating season due to heat.
QUALIFIED
INSTALLER
Dimensions
18”
Zero Clearance to Stand-off
offs
at Back and Sides
Electrical
x
x
8-1/2”
(for ambient
light only)
Gas
24”
Center
Line
7-1/8”
6-5/8” dia. Venting
Electrical
(for ambient
light only)
50” to underside of header
51-1/2” to top of cement board
28””
33”
46-3/4”
Zero Clearance
to Stand-Offs
at Top
”
66
43”
32-1/2”
Location
21
QUALIFIED
INSTALLER
Mantel Clearances
Combustible Mantel—Left Side View
Ceiling
Combustible wall finish
allowed above cement board
Mantel Projection
(from Face of Cement Board)
50”
45”
43” Mantel
Height
41” (from
39” Bottom
of Unit)
36” Min. to Ceiling
0 2” 4” 6” 8” 10” 12”
36”
Firebox Height
Face of
Cement Board
Fireplace
Opening
33”
28”
Bottom of Unit
Left Side View
22
QUALIFIED
INSTALLER
Mantel Clearances
Combustible Sidewall / Mantel Leg—Top View
FIREPLACE
Shading denotes
allowable location
for combustible
mantel legs
Face of
Finished
Wall
Fireplace Opening
32-1/2”
1”
2”
3”
4”
5”
Wall
5” 4” 3” 2” 1”
Note
Right Side Clearances
are the same
Min. 6”
between edge
of opening
and wall
Top View
23
QUALIFIED
INSTALLER
Hearth Requirements
General Hearth Considerations
! WARNING
SAFETY WARNING! The Ventana is a very effective radiant heater. The hearth/floor in front of
the heater can get very hot (in excess of 200ºF). Locating the unit raised above the hearth/floor or
adding one of the optional screen fronts or a generic freestanding screen in front of the unit can
greatly reduce hearth temperatures. Any hearth within 4 inches of the base of the heater must be
constructed of non-combustible materials (see diagrams in the following pages). Note that some
materials, although safe can degrade due to heat—take this into consideration when choosing
materials.
When the appliance
is installed directly on
carpeting, tile or other
combustible material
other than wood flooring,
the appliance shall be
installed on a metal or
wood panel extending the
full width and depth of the
appliance
Top of Finished Hearth
Must Be Flush With
Bottom of Heater to
accommodate some
optional mantels and
trims. See Option section
at the beginning of this
manual for optional
accessories.
NOTE:
• Unit will need to be raised
in almost every case to
accommodate hearth or
combustible flooring.
• Non-combustible hearth
required if bottom of
fireplace is less than 4” from
combustible floor in front.
24
Hearth Requirements
QUALIFIED
INSTALLER
Rules
1. Any hearth/floor in front of fireplace within 4 inches of the bottom of the unit must be non-combustible and
project a minimum distance as shown on page 26. The hearth/floor must have a non-combustible finish applied
over the 1/2 inch insulation board provided with the engine. This insulation board acts as a thermal break.
2. Minimum hearth projection is determined by a combination of the height of the hearth above the surface of
combustible floor or carpet and the distance between the hearth and the bottom of the fireplace.
3. Combustible baseboards (1 inch thick or less) located on the wall are acceptable provided they are located
below the base of the raised fireplace.
Unit Raised Above Combustible Hearth or Floor
Face of
Cement
Board
4” MIN.
Combustible
Floor
Base of Fireplace
Top Face of
Combustible
Floor or
Carpet
When the appliance is installed directly on
carpeting, tile or other combustible material
other than wood flooring, the appliance
shall be installed on a metal or wood panel
extending the full width and depth of the
appliance
25
QUALIFIED
INSTALLER
Hearth Requirements
Unit With Site-Built Non-Combustible Hearth Extending
When using Optional Trims and
Mantels, Surface of Finished
Hearth Must Be Flush With
Bottom of Fireplace
Example: If the fireplace is raised 2” above
combustible floor, the non-combustible-flushwith-bottom-of-fireplace hearth must project a
min. of 6” in front of the fireplace.
Front of Fireplace
(Surface of Cement Board)
(otherwise, optional trims will not fit)
Raised 4”
above combustible floor
Surface of Hearth
(non-combutible material on
non-combustible insulation board
see diagram below)
Min. Hearth Projection
Required to Protect
Combustible Floor
4”
3”
Raised 3”
above combustible floor
2”
Raised 2”
above combustible floor
1”
Raised 1”
above combustible floor
Bottom of
fireplace
Wood is Allowed
Directly Below Fireplace
Non-combustible substrate
construction detail
3”
6”
9”
DO NOT FINISH ABOVE
THIS HEIGHT!
(Hearth MUST be at this height
when using certain accessories)
Non-Combustible
Finish
12”
Surface of
Combustible
Floor or Carpet
1/2” Insulation
Board supplied
with fireplace
Bottom of
fireplace
See Chart above for Required Projection
Wood is Allowed
Directly Below Fireplace
Using 616/617STK Stone Trim Kits
616STK/617STK
Leg & Hearth
Surface of
Combustible
Floor or Carpet
Combustible
Floor Allowed
2“
Bottom of
fireplace
Air Gap
Wood is Allowed
Directly Below Fireplace
26
Surface of
Combustible
Floor or Carpet
QUALIFIED
INSTALLER
Framing
Between underside
of header and base of
heater. Note: May
increase if raising heater
further. See Hearth
Requirements Section.
1/2” thick cement board required
above and on each side of engine
(supplied w/engine) - Combustible
wall finish may butt up to but not
cover cement board
When the appliance is
installed directly on
carpeting, tile or other
combustible material
other than wood
flooring, the appliance
shall be installed on a
metal or wood panel
extending the
full width and depth
of the appliance
50”
24
”
”
/2
1
3
4
FRAMING DIMENSIONS
Any surface directly in front of
the unit which is at a height of
less than 4” from the bottom of
the unit must be non-combustible.
See chart for minimum
non-combustible projection
required to protect combustible
flooring in front.
27
QUALIFIED
INSTALLER
Venting
Vent Material
Wall Thickness
This unit is approved for installation using
4 x 6-5/8 inches co-axial direct vent pipe and
accessories as listed in the Approved Venting
Components section on pages 47–48 of this
manual. Follow the installation instructions
supplied with the individual venting accessories.
The appliance vent is suitable for penetrating a
combustible wall assembly up to 8 inches in thickness.
A non-combustible wall can be of any thickness up to
the maximum horizontal run of vent pipe allowed for
the particular installation.
This unit may also be converted to co-linear (2 x 3 in)
venting for use in solid-fuel burning fireplaces and
chimneys using adapters and accessories—see the
Approved Venting Components section on pages
47–48 of this manual.
Vent Sealing
Seal all outer coaxial pipe and elbow joints, including
sectioned elbow joints, using high quality, high temperature 2 inch wide self-adhesive aluminum foil tape
(Nashua-322-2 brand or similar). Wrap the tape completely around all joints and press firmly to seal.
A high temperature black silicone sealant may be used
in the outer joints as a substitute to foil tape.
Ensure all the pipe joints have a minimum of 1 ¼ inch
overlap.
Tape all joints
(including all
elbow joints)
28
Framing Vent in Combustible Walls &
Ceilings
When penetrating through combustible walls and
ceilings, frame a minimum of 10 x 10 inches opening
and ensure that the insulation is kept clear of the vent
pipe using either a wall thimble or an attic insulation
shield. Follow the installation instructions supplied
with the individual venting components.
10” (254 mm)
Align the vent
center to the
center of the
frame
10” (254 mm)
All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow. The
final pipe length, when terminating through the wall
may be graded downwards slightly to prevent water
migration.
Co-axial Venting
QUALIFIED
INSTALLER
Important Installer Notice – Weather Sealing &
Vapor Barriers
It is the installer’s responsibility to ensure that vent installations
through exterior walls are caulked and weatherproofed in such a
manner as to:
• Prevent rain water from entering the wall from the weather side
by adequately caulking the outer vent plate to the exterior wall
surface.
• Prevent moisture inside the home from penetrating into the wall
structure by ensuring the inside wall plate is adequately sealed to
the inside vapor barrier.
• Prevent rain water and moisture from entering the walls by sealing the joints between the outer vent tube and the inner and outer
wall plates.
We recommend the use of a high quality polyurethane sealant.
Typical Venting Components
2-PIECE
WALL
THIMBLE
VERTICAL
TERMINATION
STORM
COLLAR
FLASHING
ATTIC
INSULATION
SHIELD
HORIZONTAL
TERMINATION
ATTIC
FIRESTOP
CEILING
FIRESTOP
90˚ ELBOW
PIPE
LENGTH
PIPE
LENGTH
PIPE
LENGTH
PIPE
LENGTH
29
QUALIFIED
INSTALLER
Co-axial Venting
How to Read the Venting Chart
The chart below applies to roof or wall termination.
1. The total length of the vent pipe cannot exceed
40 feet (12.2 m).
2. The minimum vertical height with roof termination
is 6 feet (1.83 m).
3. Any combination of rise and run can be used as
long as they are within the allowable limits shown
on the chart below.
4. A maximum of 4 x 90 degrees elbows—or
equivalent (2 x 45 degr. = 90 degr.)—can be used.
5. Each 90 degrees elbow installed on the horizontal
plane is equivalent to a 3 feet horizontal pipe;
therefore, 3 feet must be subtracted from allowable
horizontal run (45 degrees elbow is equivalent to
18 inches horizontal pipe.)
6. All horizontal pipe runs must be graded 1/4 inch per
foot upwards in the direction of the exhaust flow.
The final pipe length, when terminating through the
wall may be graded downwards slightly to prevent
water migration.
7. A restrictor is required for many installations—see
next section.
Venting Chart
4 x 90º ELBOWS
MAXIMUM (or equivalent)
H2
Top of
horizontal
pipe
V3
Allowable Vent
Configurations
3”
1”
40
Bottom & sides
of horizontal pipe
V2
1”
H1
38
36
All around
vertical
pipe
NO INSTALLATION
34
32
MINIMUM
VERTICAL
RISE: 2’
#4 Restrictor
30
28
Min. 12”
pipe
Max. 24” pipe if
min. vertical rise
is used
V1
Max. 6” pipe
if min. vertical
rise is used
45º elbow
directly on
flue collar
26
VERTICAL RISE (ft)
Min. 2’
before
elbow
#3 Restrictor
24
22
20
18
Example 1
#2 Restrictor
16
14
12
10
#1 Restrictor
8
6
Example 1
V Value = V1 (6’) + V2 (6’) + V3 (2’)= 14’
H Value = H1 (3’) + H2 (3’) = 6’
#2 Restrictor position required
30
4
No Restrictor
NO INSTALLATION
2
2
4
6
8
10
12
14
16
HORIZONTAL RUN (ft)
18
20
QUALIFIED
INSTALLER
Co-axial Venting
Restrictor
MANY INSTALLATIONS REQUIRE A RESTRICTOR
for improved flame picture and performance, This unit
is supplied with one restrictor having four different
positions or settings. The level of restriction required
depends on the vertical rise in the venting system and,
to a lesser degree, the horizontal run and number of
elbows.
INSTALL HERE
The amount of restriction is based on laboratory tests.
The ideal restrictor position may vary slightly, especially
when the vent pipe length is near the limits of the
acceptable configurations for each type of restrictor.
The chart on the previous page shows the vent
restrictor required relative to the length of the vent pipe.
To install the restrictor:
1. On an engine previously installed, open the panels
on each side of the window. Remove the window
skirt, the window, the logs, the right and rear top
brick panels.
2. According to the installation, look up the venting
chart on the previous page to know what position
the restrictor should be fitted in.
3. Remove the screws (2) on each side of the venting
port in the firebox roof.
4. Place the restrictor in the required position over the
port aligning it with the two screw holes.
5. Fit the screws and tighten.
6. Continue the installation or, for
an engine previously installed,
replace the right and rear top brick
panels, the logs, the window and
the window skirt. Close the side
panels.
Position #1
Position #2
Position #3
Position #4
31
QUALIFIED
INSTALLER
Co-axial Venting
Vent Termination
• The vent terminal must be located on an outside
wall or through the roof.
• This direct vent appliance is designed to operate
when an undisturbed airflow hits the outside vent
terminal from any direction.
• The minimum clearances from this terminal that
must be maintained when located on an outside
wall are shown in the figure below. Any reduction
in these clearances could result in a disruption
of the airflow or a safety hazard. Local codes or
regulations may require greater clearances.
• The vent terminal must not be recessed into a
wall or siding.
• The vent terminal should be positioned where it
will not be covered by snowdrifts.
• Sidewall vent terminations within 7 feet of grade
require a terminal guard such as the 845TG.
Min. 72”
Max. 72”
G
V
A
Alcove detail
(open on one
side) Normal
ceiling/soffit
clearances
apply.
KEY
VENT TERMINAL LOCATIONS - MINIMUM DISTANCES
A
B
C
D
Clearance above grade, verandah, porch, deck or balcony
Clearance to window or door that may be opened
Clearance to permanently closed window (recommended to prevent condensation on window)
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of
2 feet (60 cm) from the center-line of the terminal
Clearance to unventilated soffit
Clearance to outside corner
Clearance to inside corner
Horizontal clearance to center-line of meter/regulator assembly located within 15 feet (4,6 m)
below the terminal
Clearance to service regulator vent outlet
Clearance to non-mechanical air supply inlet to the building or the combustion air inlet to any
other appliance
Clearance to a mechanical air supply inlet
Clearance above paved sidewalk or a paved driveway located on public property
Note: A vent must not terminate directly above a sidewalk or paved driveway, which is located
between two single-family dwellings and serves both dwellings
Clearance under a verandah, porch, deck or balcony
Only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides
beneath the floor
E
F
G
H
I
J
K
L
M
Note:
32
Local codes and regulations may require different clearances.
MINIMUM
CLEARANCE
Inches
Cm
12
30
12
30
12
30
18
46
12
12
12
36
30
30
30
90
36
12
90
30
72
84
180
210
12
30
QUALIFIED
INSTALLER
Co-axial Venting
Vertical Vent Termination
Roof
Pitch
Flat to 7/12
Minimum
"H" (feet)
1'
Over 7/12 to
8/12
1.5'
Over 8/12 to
9/12
2’
Over 9/12 to
10/12
2.5’
Over 10/12 to
11/12
3.25’
Over 11/12 to
12/12
4’
Over 12/12 to
14/12
5’
Co-Linear Venting
Conversion to Co-Linear Liners using generic Co-Linear Adapters
Co-linear portion of vent system may only be installed within a solid-fuel burning fireplace and chimney.
The appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance.
Requires a Co-Axial to Co-Linear appliance Adapter, two
Approved co-linear
lengths of 2-ply 3” dia. flexible chimney liner approved for
termination or approved
co-linear adapter
venting gas appliances, a co-linear termination kit and
2 x 3”
and approved
liners
co-axial
Flashing
flashing or a co-linear to co-axial adapter and either a
termination
high wind vertical vent terminal cap or a low profile vertical
termination. Firebox top zero clearance stand-offs supplied
Co-linear
with the heater are not required for this application.
adapter
Rules for Co-Linear Venting
• Maximum 40 feet vertical pipe
• Minimum 10 feet vertical
• Maximum offset 8 feet with liners at minimum 45 degrees
from horizontal plane
• Restrictor: Use #4 position for all co-linear installations—
refer to page 31 for restrictor positioning.
3” min.
bend radius
2 x 3”
liners
10-1/2”
(267 mm)
Co-linear
adapter
3”
(76 mm)
7-1/8”
(181 mm)
Ventana
Vogue
engine
engine
7-1/2”
(191 mm)
Dura-Vent #46DVA-GCL
Co-Axial to Co-Linear Adapter
Ventana with co-linear adapter
Co-Linear installation into existing F/P
33
QUALIFIED
INSTALLER
Co-Linear Venting
Co-linear terminal configurations
Alternate to 559CLT/559FSK Conversion
10”
Co-Linear to Co-Axial
Adapter
10”
7-5/8” dia.
collar
3” Inlet & Exhaust
Collars
559CLT Co-Linear Terminal
Flashing
559FSK Flashing Kit
Terminal Cap
Installation Planning
Installer—READ THIS FIRST
Only qualified licensed or trained personnel
should install this appliance.
BEFORE YOU START, YOU NEED TO KNOW
FROM THE HOMEOWNER:
• The height of the floor or hearth finish;
• The thickness and type of the wall finish
around the firebox opening;
• What accessories (surround, door, etc.) will be
installed with this fireplace if any;
• The venting configuration.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
34
Unpack the appliance.
Check that you have everything.
Finish framing.
Fit appliance into framing.
Remove overlay, barrier screen bottom brackets
and fix the appliance to the floor.
Reinstall overlay and screen bottom brackets.
Install venting system.
Install restrictor.
Connect and test gas supply.
Install bricks and logs.
Refit window.
Connect electrical wiring for decorative light.
Install optional wall switch if required.
14. Put batteries in receiver and remote control
handset.
15. Perform initial remote control set-up.
16. Verify operation and adjust aeration settings.
17. Install the remote control handset wall holder.
18. Instruct the homeowner on the operation and
maintenance of the fireplace.
19. Install the window skirt.
20. Install the control access doors.
21. Install the andirons and fret if required.
22. Finish the wall around the fireplace.
23. Install the surround/doors/mantel if required.
24. Install the barrier screen.
Installation
Unpack the appliance
To assist you, we have included the cement and
hearth insulation boards required in the installation.
The boards need to be removed and reinstalled with
care. Two of the boards are fixed temporarily to the
back of the appliance for transportation purpose. When
disassembling the crate into which the appliance is
located, be careful not to damage these boards.
Beware of sharp edges! Wear gloves!
1. Remove the cardboard wrapping and the wood
pallet from the appliance and discard.
2. Remove the cement board and hearth insulation
board from the rear of the appliance and set aside
with screws for future use.
3. Remove the cement boards from the front of the
appliance and set aside with screws for future use.
These boards must be removed to allow space to
fix the fireplace to the framing through its four side
tabs.
4. Unpack any loose items from around the appliance.
5. Remove the window and set aside in a safe place
to avoid damage—see next page.
6. Verify that you have all the components
required for the installation, including:
- brick panels (in separate carton);
- surround/doors/fret/andirons;
- venting components and accessories;
- electrical components for installation of the
decorative light wall switch.
7. The standoffs are supplied flat on the firebox and
fixed at one end. Bend them as shown and fix the
loose end to the top of the firebox.
Fold Lines
QUALIFIED
INSTALLER
8. Remove the 4 screws retaining the engine to its
pallet.
9. On each side of the appliance, bend out the 2 fixing
tabs.
10. Taking great care not to cut your hands on the
sheet metal edges, lift the appliance out of its
packing base and place in the framing. Make sure
that the unit is at the right height with consideration
to the trim and the height of the hearth or
combustible flooring.
11. Secure the fixing tabs (2 on
each side) to the framing
studs as shown.
12. Re-install the cement boards on each side and
on top of the firebox opening re-using screws
removed in 2. and 3.
13. Incorporate the hearth insulation board in the
construction of the hearth as required, following the
guidelines provided in the Hearth Requirements
section of this manual.
35
QUALIFIED
INSTALLER
Installation
Fix the appliance to the floor
1. Remove the front bottom overlay panel and the
barrier screen lower brackets by removing 1 screw
on each side and sliding the panel out from under
the firebox.
2. Screw the appliance to the floor with 4 countersunk
wood or cement screws (not provided).
3. Reinstall the overlay panel sliding it in the clips
under the edge of the firebox. Add the barrier screen
brackets and fix them with the overlay back to the
bottom sides of the opening frame with 1 screw on
each side.
36
Installation
QUALIFIED
INSTALLER
Remove Window
The window is held in place by a spring-loaded lever on
each side.
1. To remove the window, locate the levers on each
side of the window towards the top. Using your
finger, pull the lever towards you and unhook it from
the window frame bracket.
2. Gently pull the top of the window outward.
3. Lift the window out of its bottom railing and set it
aside in a safe place to avoid damage.
Window frame
Bottom railing
Section Views
Connect Gas Supply
The gas supply inlet connection is a 3/8 inch NPT male
connector and is located on the left hand side of the
firebox.
copper tubing must be internally tinned for protection
against sulfur compounds.
Unions in gas lines should be of ground joint type.
X
Use only new black iron or steel pipes or copper tubing
if acceptable—check local codes. Note that in USA,
The gas supply line must be sized and installed to
provide a supply of gas sufficient to meet the maximum
demand of the appliance without undue loss of pressure.
Sealant used must be resistant to the action of all gas
constituents including LP gas. Sealant should be applied
lightly to male threads to ensure excess sealant does not
enter gas lines.
37
QUALIFIED
INSTALLER
Installation
The unit is supplied with a stainless steel flex line to
allow the appliance to be disconnected for service.
The flex line is supplied loose to avoid damage during
shipping. Connect the flex to the appliance valve as
shown below. An individual shut-off valve (not supplied)
is required on the supply line ahead of the flex
connector.
3/8” NPT male
connector
Pressure test the supply line for leaks.
The appliance and its individual shut-off valve must be
disconnected from the gas supply piping system during
any pressure testing of that system at test pressures in
excess of 1/2 psig (3.5 kPa).
Supplied loose
The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2 psig (3.5 kPa).
Failure to either disconnect or isolate the appliance
during pressure testing may result in regulator or valve
damages and void the warranty. Consult your dealer in
case of damages.
Control
Valve
Pressure Test Points
The minimum supply pressure is given in the section
Specifications of this manual—page 19.
All piping and connections must be tested for leaks
after installation or servicing. All leaks must be
corrected immediately.
When testing for leaks:
• Make sure that the appliance is turned off.
• Open the manual shut-off valve.
• Test for leaks by applying a liquid detergent or soap
solution to all joints. Bubbles forming indicate a gas
leak.
Never use an open flame to check for leaks.
Correct any leak detected immediately.
The pressure test tapping locations are shown in
the figures on the right. An internal regulator within
the valve controls the burner manifold pressure. The
correct pressure range is shown in the table in section
Specifications of this manual on page 19. The pressure
check should be made with the burner alight and at its
highest setting. See Lighting Instructions section for full
operating details on page 16.
38
Manifold Pressure
Adjustment
behind Plastic
Cap
Valve Assembly
Manifold Test
Pressure
Valve Inlet
Pressure
Pressure Testing
QUALIFIED
INSTALLER
Installation
Install Liners
The following guidelines apply for all brick liners.
1. Inside the firebox, on the top of each side, release
the screw of the side brick anchors (one per side).
4. Place the top panel over the top edge of the rear
and side panels. Leave the panel to balance there
until right hand side panel is installed.
2. Place the rear panel against the back of the firebox,
behind the retainer at bottom.
5. Hold the right hand side panel at an angle and
insert it totally inside the firebox, behind the
top outer edge of the firebox. This will greatly
facilitate the installation. Slide the bottom first
and then the top against the side of the firebox.
You may have to lift the top panel slightly to avoid
scratching it. Rotate the side brick anchor to hold
the panel in place.
3. Hold the left hand side panel at an angle and insert
it totally inside the firebox, behind the top outer
edge of the firebox. This will greatly facilitate the
installation. Slide the bottom first and then the top
against the side of the firebox. Rotate the side brick
anchor to hold the panel in place.
Top of panel
behind the top
outer edge of
the firebox
Top of panel
behind the top
outer edge of
the firebox
6. Make any adjustment by moving the rear top panel
slightly.
7. Tighten the side brick anchors on each side of the
firebox.
39
QUALIFIED
INSTALLER
Installation
Install Ceramic Logs
The ceramic logs are supplied in two packages. Unpack them very carefully to avoid damaging the fragile
material. Install the logs as shown below. Please note that the position of the Logs is critical to insure proper
performance of the appliance.
1. Place the Rear Log on the rear log support behind the burner. Pull log forward until it contacts at ends. See
detailed view.
Touches
Pins for Top Left and Right Logs
here
Rear Log position
against the back of
middle log support
2. Place the Middle Log on the pins of the middle log support on the burner. Move the log slightly forward so it sits
against the front tabs of the log support. See detailed view.
Pins for Middle Left and Right Logs
Middle Log position
on pins at each end
3. Place the Front Log behind the grate with its rear
right notch on the middle log’s support front tab. The
log must also be flat against the burner plate. See
detailed views.
Notch in back
side of log lines
up with bracket
Front Log bottom
should contact sheet
metal below
40
Installation
4. Place the narrow end of the Middle Left Log on the
left pin of the middle log with its wider end resting on
the front log.
Place on pin with log
projecting forward
6. Place the Top Left Log on the left pin of the rear log
with its end resting on the middle left and front logs.
Refit and Check Window
1. To refit the window, place it in its
bottom railing and push its top against
the firebox.
QUALIFIED
INSTALLER
5. Place the charred end of the Middle Right Log on
the right pin of the middle log with its lighter end
resting on the notch on the far right of the rear log.
Place on pin with log
projecting backward
7. Place the Top Right Log on the right pin of the rear
log with its narrow end resting on the middle and the
middle right logs.
Section
Views
41
QUALIFIED
INSTALLER
Installation
2. While you hold it, pull the side levers back into the
window brackets on each side.
3. Pull out the top of the window and release it to
insure the springs return it.
4. Apply light hand pressure against the window frame
sides to bed-in the window seal.To refit the window,
place it in its bottom railing and push its top against
the firebox.
5. While you hold it, pull the side levers back into the
window brackets on each side.
6. Pull out the top of the window and release it to
insure the springs return it.
IMPORTANT: To ensure a safe operation,
ensure that the spring-loaded mechanism
functions properly.
Hot Glass Warning Plate
7. Apply light hand pressure against the window
frame sides to bed-in the window seal.
8. If the Hot Glass Warning plate has been
removed from the front lower corner
of the window, reinstall it by sliding
it between the glass and the frame as
indicated.
Synchronize Remote Control
The receiver and the handset of the remote control
system must be initially synchronized before the first
use.
1. Insert alkaline batteries in the remote control
receiver and handset. The receiver is located left
of the firebox.
2. With a sharp object, press and hold the receiver’s
reset button until you hear one short and one long
beeps. Release the reset button after the second
beep.
3. Within the subsequent 20 seconds, press the small
flame button ( ) on the remote handset until you
hear two short beeps confirming the sychronization
is set.
This is a one time setting only and is not required when
changing the batteries in the remote receiver. The
remote control system is now ready to use.
42
QUALIFIED
INSTALLER
Installation
Install Electrical Components for Decorative
Lighting
Wall Dimmer Switch
The electrical installation must be performed
by a qualified installer and must be electrically
wired and grounded in accordance with local codes,
or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70 or the Canadian
Electrical Code, CSA C22.1.
The fireplace is equipped with a decorative light
located in front of and above the window. The
light is pre-wired to a junction box on the right
hand side, inside the fireplace. A switched power
supply to the knock-out on the right hand side is
required to complete the installation. A dimmer is
recommended—see specifications below.*
1. Turn the power off at the fuse box.
2. Decide where the dimmer will be located. If you are
not sure, check with the homeowner.
3. Install the outlet box and connect the dimmer to the
electrical wiring (all components—not supplied—
available from your local electrical hardware store).
4. Locate the electrical wire in the junction box inside
the firebox outer lining, on the right hand side.
Remove its cover.
5. Run the electrical wires from the dimmer and
thread it through the knock-out of the firebox to the
junction box.
6. In the junction box, hardwire the harness to the
electrical wire. Refit the junction box cover. Outside
the firebox, fit a cable clamp.
7. Fit the cover plate to the wall (not supplied).
Fitting the Decorative Light bulb
1. Locate the decorative light fixture inside the firebox
top, just in front of the window.
2. Loosen the screws of the tabs located on each side
of the decorative light fixture.
3. While holding the glass cover, turn on of the
retaining tabs to free the glass.
4. With a gloved hand, take the halogen light bulb
from its packaging and insert in the light fixture.
5. Turn the power back on at the fuse box.
6. Turn on the dimmer switch to ensure good function
and then, turn it off.
7. Put the glass cover back in place and, while
holding it, turn the retaining tabs back to cover the
glass edges.
8. Tighten the tabs screws.
Electrical
Connection
Point
X
Knock-out on
Outside of
Fireplace (use
proper cable
clamp)
Standard
octagon
Junction
Box + Cover
Accessible
inside
Fireplace
to Dimmer
Switch
* Recommended Dimmer Switch (not
supplied):
Switch Type: Single-Pole
Type: Electro-Mechanical none preset or
Preset
Load Rating: 600W
Voltage: 120 Volt AC 60 Hz
Action: Standard ON/OFF
Protection: Radio/TV Filter
Standards and Certifications: UL/CSA
Tab
Light fixture with glass cover
Tab
Light fixture without glass cover
100W Halogen Light Bulb (119mm)
43
QUALIFIED
INSTALLER
Installation
Check Operation
Turn the fireplace flame up and down using the
remote control to confirm that the full range of inputs
is achieved—see the remote control operation
instructions on pages 11–15.
Adjust Aeration (if necessary, NG units only)
(LPG units do not have any primary air adjustment.)
Light the fire and allow the unit to warm up for 10–15
minutes to evaluate the flame picture. Natural gas
burners are equipped with an adjustable shutter to
control primary aeration. See the figures below. The
shutter is factory-set to an aeration gap which will
give optimum performance for the vast majority of
installations.
In a few unusual installations, the flame picture may
be improved by adjusting the aeration. The need for
adjustment should be determined only by operating the
appliance with the ceramic logs and window installed.
Increasing aeration will cause the flames to appear
more transparent and blue showing more ceramic log
glow.
Decreasing aeration will cause the flames to appear
more yellow or orange showing less ceramic log glow.
Too little aeration may result in black carbon
forming and dropping into the firebox.
Air Shutter (NG units only)
Air Shutter
Air Shutter
Retainer
Air Shutter in
Closed Position
Air Shutter in
Open Position
Install Window Skirt and Side Doors
The fireplace comes equipped with a window skirt to
hide the underside of the firebox and two side steel
doors to hide the gas and electrical controls.
1. To install the window skirt, simply hook it to the
bottom frame of the window as indicated.
2. Sort the left hand side and the right hand side
doors—the tab to open the door should be towards
the outside at the bottom.
Take one door and locate the top hinge pin in the
holed bracket located inside the top front of the
outer firebox liner.
3. Slide the door up as much as possible and fit the
lower hinge pin in the bottom hole.
4. Repeat with the other door.
The doors should be maintained closed by a magnet
on each side of the window frame.
44
Tab at
bottom
QUALIFIED
INSTALLER
Installation
Install Barrier Screen to the Appliance
A barrier screen is supplied with this appliance to install
in front of the window. The barrier screen is designed
specifically to prevent any contact with the glass of
the fireplace which becomes hot during operation and
remains hot when cooling.
To install the screen:
1. Once the trim is installed on the fireplace or the wall
finish is done around the opening of the fireplace,
adjust the convection baffle at the top of the opening
of the fireplace by releasing the two screws holding
it and pushing it as far in as possible. Tighten the
screws.
a
a
b
b
Push convection baffle as far in as possible
2. Hook the barrier screen’s top tabs in the slots of the
convection baffle (a).
3. Push the screen up and hook the bottom serrated
tabs to the brackets at the bottom of the fireplace
opening (b).
Install Handset Wall Holder
Alternative 2
Alternative 3
Packing Contents:
The remote control kit for this
fireplace comes complete with a
1 Wall Bracket A
wall-mounted holder. This holder
2 Screws B
is not required in all installations
1 Screw C
but is provided as an optional
2 Wall Anchor D
1 Spacer E
feature for those customers who
(detach before assembly)
wish to mount the remote handset
Switch Plate
to the wall.
1 Wall Bracket F
To install the holder to the wall,
find a convenient location and
Alternative 1
use the hardware provided with
the kit. See the diagram below
for required hardware and
configurations. Note that the
holder can be installed at the
base of a light switch plate.
IMPORTANT. The location of the remote control handset is important to assure proper temperature regulation. To
obtain a constant temperature, we recommend that the handset should be between 3 and 15 feet away from the
appliance but not directly above it. We also advise that the handset should be located away from any other heat
source and not in direct sunlight as this may affect the temperature sensor located in the remote handset.
45
QUALIFIED
INSTALLER
Wiring Diagram
Optional Wall
Switch Kit
1265WSK
Connector
Yellow
GV60 Wiring Diagram
46
Red
QUALIFIED
INSTALLER
Approved Venting Components
Approved Direct Vent Suppliers for Valor Models 1100, 1150, 12005, 1500, 16005 and 17006
DURA-VENT
SELKIRK
ICC EXCEL
DIRECT
SECURE
VENT
RLH
INDUSTRIES
AMERIVENT
MILES
INDUSTRIES
BDM
Venting Parts Code / availability by Manufacturer
Standard Co-axial
46DVA-HC
4DT-HC
TM-4HT
—
—
4DHC round
658DVK2
940160
Deluxe Co-axial
—
—
TM-4DHT
—
—
4DHCS square
—
940160
High Wind Co-axial
—
—
—
SV4CHC
—
—
—
Horizontal
Venting Parts
Description
Standard Co-axial
46DVA-VC
4DT-VC
TM-4VT
—
HSDV46581313
4DH-1313
—
Vertical
Aluminum
Flexible
Liner
Adjustable Pipe Length
4” x 6-5/8”
DV 45°
Elbows
940364
940206LP
High Wind Co-axial
46DVA-VCH
—
—
SV4CGV
—
—
—
—
Extended Co-axial
46DVA-VCE
—
—
—
—
—
—
—
—
HS-C33U-99
HS-C33U-99
HS-C33F-1313
HCL-99-33
HCL-99-33
Co-linear
46DVA-CL33
46DVA-CL33H
46DVA-CL34
46DVA-33P
46DVA-CL34P
Snorkel, 14” Rise
46DVA-SNK14
4DT-ST14
TM-4ST14
—
—
4D14S
—
94040614
Snorkel, 36” Rise
—
3PDVCV
—
HS-C33F-1313
—
HCL-913-33
HCL-913-33
HCL-1313-33
940033B
559CLT
HCL-1313-33
—
940034B
940033HWS
940033RD
46DVA-SNK36
4DT-ST36
TM-4ST36
—
—
4D36S
—
94040636
Universal Adapter 3”
Flex Coupler
2150
—
TM-CFAA3
—
—
—
—
95090390
Co-linear Flex
Connector
46DVA-ADF
—
—
—
—
—
—
—
Co-axial-to-Co-linear
Adapter
46DVA-GCL6
—
TM-4CAA6
—
—
4DCAB336
Co-linear-to-Co-axial
Adapter
46DVA-GK
—
TM-4CTA
—
—
4DCAT33
1156CLA5, 6 9401064336
—
—
NOTE: 2-ply liner approved to CAN/ULC S635 suitable for venting gas appliances. As manufactured by Z-Flex,
Flexmasters or others.
3” or 4” diameter
2280 Series
4” to 10”
1-1/2” to 6”
1-1/2” to 12”
Galvanized
Black
Galvanized
Black
Galvanized
—
AF3-35L
4DT-ADJ
4DT-ADJ(B)
—
—
—
—
Black
1-1/2” to 24”
Galvanized
—
—
—
—
—
—
—
4D7A or 4D7AB
(3” to 5”)
—
94610608
(4” to 8-1/2”)
—
4D12A or 4D12AB
(3” to 10”)
—
94610616
(4” to 16”)
—
4D16A or 4D16AB
(3” to 14”)
—
—
—
4D26A or 4D26AB
(3” to 24”)
—
—
4D45L
—
94620645
4D45LB
—
94620645B
—
—
—
—
SV4LA12
TC-4DLTB
SV4LBA12
—
Galvanized
46DVA-E45
—
TE-4DE45
Black
46DVA-E45B
—
Galvanized Swivel
—
4DT-EL45
4DT-EL45(B)
Galvanized
46DVA-E90
—
Black
46DAV-E90B
—
Galvanized Swivel
—
4DT-EL90
Black Swivel
—
4DT-EL90(B)
SV4LA
SV4LBA
TC-4DLT
—
Black
952703
—
—
Black Swivel
DV 90°
Elbows
—
940264
—
Vent Adapters /
Couplers
Termination Caps
4DVC
SV4LA24
SV4LBA24
—
TE-4DE45B SV4EBR45
—
TE-4DE90
SV4E45
SV4EB45
—
TE-4DE90B SV4EBR90
—
SV4E90
SV4EB90
—
—
—
—
952704
4D90L
—
—
4D90LB
—
—
—
—
94620690
94620690B
47
QUALIFIED
INSTALLER
Approved Venting Components
4DT-06
TC-4DL6
SV4L6
Black
46DVA-06B
4DT-06(B)
TC-4DL6B
SV4LB6
Pipes 4” x 6 5/8” ( ID x OD )
7” long
9” long
12” long
18” long
24” long
Flashings
Various Venting System Parts
—
Galvanized
46DVA-09
4DT-09
—
—
—
—
—
—
Black
46DVA-09B
4DT-09(B)
Galvanized
46DVA-12
4DT-12
TC-4DL1
SV4L12
Black
46DVA-12B
4DT-12(B)
TC-4DL1B
SV4LB12
—
—
Galvanized
46DVA-18
4DT-18
Black
46DVA-18B
4DT-18(B)
—
Galvanized
46DVA-24
4DT-24
TC-4DL2
SV4L24
Black
46DVA-24B
4DT-24(B)
TC-4DL2B
SV4LB24
—
—
4D7B
—
4D12
4D12B
—
4D2
4D2B
—
—
—
—
—
94610609
94610609B
94610612
94610612B
94610618
94610618B
94610624
94610624B
46DVA-36
4DT-36
4DT-36(B)
Galvanized
46DVA-48
4DT-48
TC-4DL4
SV4L48
Black
46DVA-48B
4DT-48(B)
TC-4DL4B
SV4LB48
Roof Flashing
0/12-6/12
46DVA-F6
4DT-AF6
TF-4FA
SV4FA
—
4DF
(0/12-5/12)
—
949606012
Roof Flashing
7/12-12/12
46DVA-F12
4DT-AF12
TF-4FB
SV4B
—
4DF12
(6/12-12/12)
—
949606712
Flat Roof Flashing
46DVA-FF
—
TF-4F
SV4F
—
—
559FSK
949606001
SV4LB36
—
—
4D3
—
90410606B
46DVA-36B
—
SV4L36
—
4D7
94610606
Black
48” long
48
—
Black
—
Galvanized
36” long
Notes:
Galvanized
—
BDM
SECURE VENT
46DVA-06
MILES
INDUSTRIES
ICC EXCEL
DIRECT
6” long
AMERIVENT
SELKIRK
Galvanized
Venting Parts
Description
RLH
INDUSTRIES
DURA-VENT
Venting Parts Code / availability by Manufacturer
4D3B
4D4
4D4B
—
—
94610636
94610636B
94610648
94610648B
Masonry Flashing
—
—
TF-4MF
—
—
—
—
—
Wall Thimble
46DVA-WT
4DT-WT
TM-4WT
SV4RSM
—
4DWT
—
949064U
Storm Collar
46DVA-SC
4DT-SC
TM-SC
SV4AC
—
4DSC
—
94960608
Decorative Plate
46DVA-DC
4DT-CS
TM-4TR
SV4PF
—
4DFPB
—
94940612
Cathedral Ceiling
Support
46DVA-CS
4DT-CCS
—
—
—
4DRSB
—
949506KT
Ceiling Firestop /
Floor Support
46DVA-FS
4DT-FS
TM-CS
—
4DFSP
—
94980612
Attic Radiation Shield /
Firestop
—
—
TM-4AS
—
—
—
94930620A
Wall Strap
46DVA-WS
4DTWS
TM-WS
—
—
4DWS
—
949164
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
TM-VSS
SV4VS
—
4DHVS
—
94800615S
Elbow Strap / Offset
Support
46DVA-ES
4DT-OS
TM-OS
—
—
—
—
949264
Terminal Guard
46DVA-WG
—
—
—
—
—
845TG
940164SHRD
SV4BF
SV4SD
4DAIS12 (12”)
4DAIS36 (36”)
1. Follow instructions supplied with each manufacturer’s components.
2. Unless otherwise specified, all the parts and assemblies from the above table are to be used with 4” x 6-5/8” pipes.
3. Do not mix components from different vent manufacturers.
4. Termination caps manufactured by RLH Industries or American Metal Products are from Homestyle Chimney Collection and can be ordered in
one of the following finishes: a) aluminium; b) black powder coated; c) solid copper.
5. Miles Industries Valor Co-linear adapter 1156CLA cannot be used with models 1200 and 1600. Use only with models 1100, 1150, 1500 and 1700.
6. Only Miles Industries Valor Co-linear adapter 1156CLA can be used with models 1700.
OWNER’S
INFORMATION
WA
TY
N
A
RR
M
GR A
O
PR
T
LOR
OR
If you have a problem with this unit, please contact your dealer or supplier
immediately. Under no circumstances should you attempt to service the unit
in any way by yourself. The warranties in paragraphs 1 and 2 are provided
only to the first purchaser/user of this unit, are not transferable and are
subject to the conditions and limitations in paragraphs 3, 4 and 5. Please
review the conditions and limitations carefully and strictly follow their requirements.
VA
Warranty
CO M F
1. Extended Warranty Coverage
For a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at its option pay the
initial purchaser for the repair of, or will exchange the following parts or components which are found to be defective in material or
workmanship under normal conditions of use and service:
Part or Component
Exterior steel casing
Defect Covered
Corrosion
Maximum Warranty Period
10 years
Glass
Loss of structural integrity
10 years
Cast iron parts
Corrosion
10 years
Firebox and heat exchanger
Corrosion (but not discoloration) causing
loss of structural integrity
10 years
2. Two-Year Parts Warranty
In addition, for two (2) years from the date of purchase, the Company, at its option, can repair or exchange all parts and components
not listed above but that are found to have a bona fide defect in material or workmanship under normal conditions of use.
3. Conditions and Limitations
a) The warranty registration card must be completed by the initial owner and returned to the Company within 90 days of purchase.
b) Installation and maintenance must be performed by an authorized and trained dealer in accordance with the Company’s installation
instructions.
c) This warranty is void where installation of the unit does not conform to all applicable codes including national and local gas
appliance installation codes and building and fire codes.
d) The owner must comply with all operating instructions.
e) The Company is not responsible for the labor costs to remove defective parts or re-install repaired or replacement parts.
f) The first purchaser or user of the unit will be responsible for any shipping charges for replacement parts as well as travel time
incurred by the dealer to perform the warranty work.
g) This warranty applies to non-commercial use and service and is void if it is apparent that there is abuse, misuse, alteration,
improper installation, accident or lack of maintenance to the unit.
h) This warranty does not cover damage to the unit through:
i)
Improper installation, operational or environmental conditions.
ii) Inadequate ventilation in the area or competition for air from other household equipment or appliances.
iii) Damage due to chemicals, dampness, condensation, or sulphur in the fuel supply lines which exceeds industry standards.
i) This warranty does not cover glass, log breakage or damage to the unit while in transit.
j) The Company does not allow anyone to extend, alter or modify this warranty and assumes no responsibility for direct, indirect or
consequential damages caused by the unit. State or provincial laws where the first purchaser or user resides may provide specific
rights to extend this warranty and, if so, the Company’s sole obligation under this warranty is to provide labor and/or materials in
accordance with those laws.
4. Discharge of Liability
After two (2) years from the date of purchase, the Company may, at its option, fully discharge all obligations under this warranty by
paying to the first purchaser/user the wholesale price of any defective parts.
5. No Other Warranty
All obligations to repair this unit are defined in this warranty. Some states or provinces may specifically mandate additional warranties
on the part of manufacturers, but in the absence of such specific legislation, there is no other warranty or obligation expressed or
implied.
49
OWNER’S
INFORMATION
Code
Spare Parts
Description
Part
Number
Code
Description
Part
Number
1
Intake Collar
4000925
38a
GV60 Complete Valve NG
4003101
2
Intake Collar Gasket
4000942
38b
GV60 Complete Valve LPG
4003114
3
Top Standoff (2)
4001373
39
Cable Interruptor
4001035
4
Firebox
40
Switch with Cable
4001036
5
Air Inlet Duct Assembly
4001246
42
Ignition Cable
4001039
6
Rear Log Support
4001280BY
42a
Ignition Cable Sleeve
4002244
7
Front Brick Support
4001265BY
43
Thermocurrent Interruptor
4001037
8
Side Brick Anchor (2)
4001283
44
Pipe S/S Flex
4000345
9
LH Explosion Relief Assembly
4001286
46
Magnet dia. 16 x 4.5mm
420K551
10
RH Explosion Relief Assembly
4001287
47a
Log Set NG
4001223
11
Grate Mounting Clips (2)
4001402
47b
Log Set LPG
4001541
12
Cast Iron Grate Assembly
4005212AH
48
Top Left Log
4001366
13
Window Frame Assembly
4001221
49
Top Right Log
4001365
14
Window Skirt
4001445AZ
50
Middle Right Log
4001368
15
RH Side Panel
4001243AZ
51
Middle Left Log
4001367
16
LH Side Panel
4001242AZ
52
Front Log
4001369
17
1/2” Side Trim (2)
4001360AZ
53a
Middle Log NG
4001370
18
1/2” Top Trim
4001359AZ
53b
Middle Log LPG
4001534
19a
Burner Module Assembly NG
4001228S
54
Rear Log
4001371
19b
Burner Module Assembly LPG
4001229S
55
Quartz Lamp 100 Watts
4001446
20a
Pilot Assembly NG
4000727
56
Light Cover
4001353
20b
Pilot Assembly LPG
4000728
59
Handset G6R H3T5-ZV (BJ)
4001910
21
Pilot Bracket
4000729
60
Handset Wall Holder
9000008
22
Thermocouple
4000061
61
Receiver G6R-R3AM-ZV (CP)
4001911
23a
Pilot Injector #51 NG
4000735
62
Wiring Harness
4001187
23b
Pilot Injector #30 LPG
4000736
63
Cable Clip
4000012
24
Pilot Tube
4000732
64
Ceramic Liner Sets
25
Pilot Hood 2 Flame
4000730
a
Victorian Red Brick
1245VRL
26
Extended Nut
4001855
b
Frontera Stone
1250FSL
27
Electrode
4001856
c
Inca Slab
1255IBL
28a
Burner Assembly NG
4001400
d
Black Slab
1260BSL
28b
Burner Assembly LPG
4001472
65
LH Panel
29
Air Shutter (2)—NG only
4000657
a
Victorian Red Brick
4001224
30
Shutter Slider—NG only
4000759
b
Frontera Stone
4001327
31a
Injector Elbow #82 NG
4001270
c
Inca Slab
4001328
31b
Injector Elbow #360 LPG
4001494
d
Black Slab
4001478
32
Valve to Burner Pipe Assembly
4001279X
66
Top Panel
33
Location Support Assembly (2)
4001288X
a
Victorian Red Brick
4001227
34
Top Gasket
4001269
b
Frontera Stone
4001323
35
Bottom Gasket
4001363
c
Inca Slab
4001324
36
Sealing Gasket
4001364
d
Black Slab
4001481
37
Side Gasket (2)
4001268
50
Spare Parts
Code
Description
Part
Number
67
Rear Panel
a
Victorian Red Brick
4001226
b
Frontera Stone
4001321
c
Inca Slab
4001322
d
Black Slab
4001480
68
RH Panel
a
Victorian Red Brick
4001225
b
Frontera Stone
4001325
c
Inca Slab
4001326
d
Black Slab
4001479
69
Overlay (to cover front bottom FP)
70
LH Burner Support
4001511
71
RH Burner Support
4001512
72
Restrictor
4001222
73
Hot Glass Warning Plate
4003093
74
Barrier Screen
4003365
75
LH Bracket for screen
4003655AZ
76
RH Bracket for screen
4003654AZ
77
Convection baffle
4004473AZ
Micore insulation pad (not shown)
OWNER’S
INFORMATION
4001500AZ
4001489
51
OWNER’S
INFORMATION
Spare Parts
66
54
64
53a, 53b
52
50
67
1
51
65
68
2
48
3
49
47a, 47b
19a,19b
43
Module Plate
Gaskets 34 to 37
44
4
Pilot Assy
20a to 27
28a, 28b
38a,
38b
31a, 31b
33
39
40
71
42
61
42a
62
72
77
59
75
60
8
9
74
17
76
16
10
18
5
11
6
63
7
11
55
12
56
13
14
69
17
52
15
73
72
Thank You ...
For purchasing a Valor by Miles Industries. Your new radiant gas
heater is a technical appliance that must be installed by a qualified
installer.
Please fill in the information below. The information provided will be
used for customer records only.
Fireplace Information
Model Number: 1200
EAN or
EAP
Serial Number:
Date Purchase (yyyy-mm-dd):
Dealer:
Customer Information
First Name:
Last Name:
Contact Information
Email:
Mailing Address
Address:
City:
Province/State:
Postal/Zip Code:
Country:
Cut out page, fill information, and mail to Miles Industries Ltd.
Online Warranty registration at www.valorfireplaces.com
Tape Shut
Fold here
Postage
needed
Miles Industries Ltd.
190 - 2255 Dollarton Highway
North Vancouver, BC V7H 3B1
Canada
Online Warranty registration at www.valorfireplaces.com
Were you given all documentation and manuals for your product?
Thank you for choosing a Valor Product
YES
NO