SFW10XP
Operating Instructions
Instrucciones de Operacion
Mode d’Emploi
Senco Products Inc.
8485 Broadwell Road
Cincinnati, Ohio 45244
Questions? Comments?
call SENCO’S toll-free Action-line: 1-800-543-4596
or e-mail: toolprof@senco.com www.senco.com
© 2007 by Senco Products, Inc.
Warnings for the safe use of this tool are included in this manual.
Los avisos para el uso seguro de esta herramienta están incluidos
en este manual.
Les consignes pour l’utilisation en toute sécurité de cet outil se
trouvent dans ce manuel.
NFD81D Issued January 8, 2007
English
Español
Français
TABLE OF
CONTENTS
TABLA DE
MATERIAS
TABLE DES
MATIERÈS
Tool Use
Accessories
Maintenance
Troubleshooting
Specifications
Uso de la Herramienta2
Accesorios
5
Mantenimiento
6
Identificación
de Fallas
7
Especificaciones
8
2
5
6
7
8
Keep this manual available for use by all people
assigned to the use of this
tool.
For personal safety and
proper operation of this
tool, read and understand
all of these instructions
carefully.
Tool Use
2
5
6
7
8
RESPONSABILIDADES DEL
EMPLEADOR
RESPONSABILITÉS DE
L’EMPLOYEUR
El empleador debe hacer
cumplir las advertencias de
seguridad y todas las otras
instrucciones que acompañan
a esta herramienta como se la
despacha desde el fabricante.
L’employeur doit faire appliquer les consignes de
sécurité et toutes les autres
instructions qui accompagnent cet outil tel qu’il est
livré par son constructeur.
Mantenga este manual disponible para que lo usen todas
las personas destinadas a hacer uso de esta herramienta.
Ayez ce manuel à la disposition de toutes les
personnes chargées
d’utiliser cet outil.
Por razones de seguridad personal y la adecuada operación
de esta herramienta, lea y
comprenda todas estas instrucciones cuidadosamente.
Pour assurer la sécurité personnelle et le bon
emploi de cet outil, lisez et
assimilez soigneusement
toutes ces instructions.
EMPLOYER’S
RESPONSIBILITIES
Employer must enforce
compliance with the
safety warnings and
all other instructions
which accompany this
tool as shipped from the
manufacturer.
Utilisation de l’outil
Accessoires
Entretien
Dépannage
Spécifications
Uso de la Herramienta Utilisation de l’Outil
l Read and understand “SAFETY
l Antes de usar la herramienta lea
INSTRUCTIONS” manual
shipped with this tool before
using tool.
y comprenda el manual “INSTRUCCIONES DE SEGURIDAD” despachado con ella.
2
l Lisez et assimilez le manuel
“INstructions de sécurité” livré avec cet outil avant
de l’utiliser.
Tool Use
Uso de la Herramienta Utilisation de l’Outil
Español
English
l Mantenga la herramienta apun-
l Keep tool pointed away from
tando en la dirección opuesta
de usted y de otros y conecte el
aire a la manguera.
yourself and others and connect
air to tool.
l To Load:
l Para cargar:
Depress latch and slide rail
open.
Oprima el cerrojo y deslice el
carril abriéndolo.
l Lay strip of staples into maga-
l Coloque la tira de grapas dentro
Français
l Maintenez l’outil pointé à l’écart
d’autres personnes et de vousmême et
raccordez l’air à l’outil.
l Pour charger :
Appuyer sur le verrou et ouvrir
le rail en le tirant.
1
2
zine. Use only genuine SENCO
staples. Do not load with trigger
depressed.
del cargador. Use solamente sujetadores SENCO auténticos. No
cargue con el gatillo oprimidos.
l Push rail forward until it latches.
l Empuje el carril hacia adelante
hasta cerrario.
l Never use a tool that leaks air or
l Nunca use una herramienta que
needs repair.
tenga escapes de aire o que
necesite reparación.
3
l Insérer la bande d’agrafes dans
le magasin. Utilisez uniquement
les véritables agrafes SENCO.
Veillez à ne pas appuyer sur la
détente quand vous chargez.
l Pousser le rail jusqu’a encli-
quetage.
l N’utilisez jamais un outil qui a
des fuites d’air ou qui a besoin
d’être réparé.
Tool Use
Uso de la Herramienta Utilisation de l’Outil
English
Español
l Para clavar las grapas:
l To drive fasteners:
Coloque la herramienta contra la
superficie de trabajo y apretar el
gatillo.
Position tool against work surface and pull the trigger.
2
l Pour agrafer :
Position l’appareil contre la
surface de travail et presser sur
la gâchette.
l Para estas herramientas no se
l Ces outils ne nécessitent pas
necesita un punto de contacto con
de contact avec la pièce. FAIRE
la pieza de trabajo. SEA PRECAVIDO
ATTENTION car ils enfonceront
ya que estas herramientas dispaune agrafe dès que la gâchette
rarán una grapa cuando se aprieta
est actionnée.
el gatillo.
l These tools are not required
to have a workpiece contact.
USE CAUTION as these tools
will drive a fastener when the
trigger is pulled.
1
Français
l Should a staple jam occur,
l Si se produce un atascamiento
disconnect air supply.
de las grapas, desconecte el
suministro de aire.
l 1) Depress latch and 2) slide
l 1) Oprima el cerrojo y 2) desli-
rail open.
ce el carril abriéndolo.
l Si un enrayage se produit,
coupez l’arrivée d’air.
l 1) Appuyer sur le verrou et 2)
ouvrir le rail en le tirant.
1
2
l Remove staples.
l Saque las grapas.
l Enlever les agrafes.
l Remove jammed fastener.
l Remueva el sujetador atascado.
l Enlevez le projectile coinçé.
l Lay strip of staples onto rail. Use
l Coloque una tira de grapas en el
l Mettez une série d’agrafes dans
riel. Use solamente grapas SENCO genuinas (ver la Tabla de
Partes). No cargue la herramienta con el gatillo oprimido.
le chargeur. N’utilisez que de
véritable agrafes SENCO (voir
Tableau des Pièces). N’appuyez
pas sur la détente pendant le
rechargement.
only genuine SENCO fasteners
(see Parts Chart). Do not load
with trigger depressed.
l Destrabe la compuerta de
l Release staple door and slide it
las grapas y deslícela hacia
adelante.
forward.
4
l Relâcher le pousse agrafes et le
faire glisser vers l’avant.
Accessories
Accesorios
Accessoires
English
Español
Français
SENCO offers a full line of accessories for your SENCO tools, including:
l Air Compressors
l Hose
l Couplers
l Fittings
l Safety Glasses
l Pressure Gauges
l Lubricants
l Regulators
l Filters
For more information or a complete
illustrated catalogue of SENCO
accessories, ask your representative
for #MK336.
SENCO ofrece una línea completa
de Accesorios para sus herramientas SENCO, incluyendo:
l Compresores de Aire
l Manguera
l Conectores Rapidos
l Conectores
l Anteojos De Seguridad
l Manometros
l Lubricantes
l Reguladores
l Filtros
Para mas informacion ó un pour
recevoir un catalogo completo ilustrado de los Accesorios SENCO,
pregunte a su representante pour
el numero MK336.
5
SENCO offre une gamme étendue
d’accessoires pour vos outils
SENCO y compris :
l Compresseurs
l Tuyauterie flexible
l Raccords
l Lunettes de sécurité
l Manomètres
l Lubrifiants
l Régulateurs
l Filtres
Pour plus d’informations ou pour
recevoir un catalogue détaillé des
accessoires proposés par SENCO,
prenez contact avec votre
représentant SENCO (référence
catalogue : #MK336).
Maintenance
Maintenimiento
Entretien
English
Español
Français
l Read and understand “SAFETY
INSTRUCTIONS” manual
shipped with this tool before
using tool.
l All screws should be kept tight.
Loose screws result in unsafe
operation and parts breakage.
l With tool disconnected, make
daily inspection to assure free
movement of trigger. Do not use
tool if trigger sticks or binds.
l Squirt SENCO pneumatic oil
l Antes de usar la herramienta lea
y comprenda el manual “INSTRUCCIONES DE SEGURIDAD” despachado con ella.
l Todos los tornillos tienen que
mantenerse apretados. Los
tornillos sueltos pueden producir
una operación no segura y
quebraduras de partes.
l Con la herramienta desconec-
tada, haga inspecciones diarias
para asegurar un movimiento
libre del disparador. No use la
herramienta si el disparador se
pegan o se atascan.
l Aplique aceite neumático
(5 to 10 drops) into the air
inlet twice daily (depending on
frequency of tool use). Other oils
may damage O-rings and other
tool parts.
SENCO en la entrada de aire
dos veces al día (dependiendo
en la frecuencia de uso 5 A 10
Gotas). Otros aceites pueden
dañar los anillos en “O” y otras
piezas de la herramienta.
l Wipe tool clean daily and inspect
l Use soluciones de limpieza no
for wear. Use non-flammable
cleaning solutions only if necessary–DO NOT SOAK.
Caution: Such solutions may
damage O-rings and other tool
parts.
flamablés
solamente si es necesarioNO LA REMOJE.
Precaución: Tales soluciones
pueden dañar
los empaques y otras partes de
la herramienta.
6
l Lisez et assimilez le manuel
“INstructions de sécurité” livré avec cet outil avant
de l’utiliser.
l Toutes les vis doivent être main-
tenues serrées à fond. Les vis
desserrées entraînent un manque de sûreté du fonctionnement
et la rupture de pièces.
l L’outil étant déconnecté de l’ar-
rivée d’air comprimé, effectuez
une inspection journalière pour
vous assurer le libre mouvement
de la détente. N’utilisez pas
l’outil si la détente colle ou se
coince.
l Avec une burette, placer 5 à 10
gouttes d’huile pneumatique
dans l’arrivée d’air deux fois
par jour (dépend de l’intensité
de l’utilisation de l’appareil).
D’autres huiles pourraient
endommager les joints toriques
et d’autres pièces de l’outil.
l Nettoyez l’outil chaque jour à
l’aide d’un chiffon et inspectezle pour déceler une éventuelle
usure. Utilisez uniquement des
solvants non inflammables en
cas de nécessité-NE LE FAITES
PAS TREMPER !
Attention : De tels produits
peuvent endommager les joints
et autres pièces de l’appareil.
Troubleshooting
Identificación de Fallas
Dépannage
English
Español
Français
WARNING
Repairs other than those described
here should be performed only by
trained, qualified personnel. Contact
SENCO for information at
1-800-543-4596.
l Read and understand “SAFETY
INSTRUCTIONS” manual
shipped with this tool before
using tool.
SÍNTOMA
El aire se escapa cerca de la parte superior de la herramienta / Operación
lenta.
Fuite d’air près du sommet
de l’outil / fonctionnement lent.
SOLUTION
SOLUCIÓN
SOLUTION
Verify air supply / tighten screws
or install Firing System Kit A
(YK0322).
A
B
B
AVERTISSEMENT
Les réparations autres que celles
décrites ici doivent être réalisées
uniquement par du personnel
qualifié ayant reçu la formation
appropriée. Pour toute information,
prenez contact avec SENCO par
téléphone en appelant Le Distributeur agréé.
l Lisez et assimilez le manuel “INstructions de sécurité” livré
avec cet outil avant de l’utiliser.
SYMPTOM
Air leak near top of tool /
Sluggish operation
A B
ALERTA
Las reparaciones, fuera de aquellas
descritas aquí, deben de ser llevadas a cabo solamente por personal
entrenado y calificado. Póngase
en contacto con SENCO para
información
1-800-543-4596.
l Antes de usar la herramienta lea y
comprenda el manual “INSTRUCCIONES DE SEGURIDAD”
despachado con ella.
SYMPTOM
Apriete los tornillos / Verifique el
suministro de aire o instale el
Juego de Partes A (YK0322).
SÍNTOMA
SYMPTÔME
Serrez les vis à fond / vérifiez
l’alimentation en air ou remplacez les
pièces portant la lettre “A” (YK0322).
SYMPTÔME
Air leak near bottom of tool /
Poor return.
El aire se fuga cerca de la parte
inferior de la herramienta / Mal
retorno.
Fuite d’air près de la base
de l’outil / retour inadéquat.
SOLUTION
SOLUCIÓN
SOLUTION
SYMPTOM
SÍNTOMA
SYMPTÔME
SOLUTION
SOLUCIÓN
SOLUTION
Clean tool / tighten screws or install Piston Stop Kit B (YK0321).
Other problems.
Contact SENCO.
Apriete los tornillos / Limpié la
herramienta o instale el Juego de
Partes B (YK0321).
Otros problemas.
Póngase en contacto con
SENCO.
7
Serrez les vis à fond / nettoyez l’outil
ou remplacez les pièces portant la
lettre “B” (YK0321).
Autres problèmes.
Prenez contact avec SENCO.
English
TECHNICAL SPECIFICATIONS
Minimum to maximum operating pressure
Air Consumption (60 cycles per minute)
Air Inlet
Maximum Speed (cycles per minute)
Weight
Staple Capacity
Tool size: Height
Tool size: Length
Tool size: Width: Main Body
Français
SPECIFICATIONS TECHNIQUES
Pression de travail min. et max.
Consommation d’air (60 cycles par minute)
Admission d’air
Vitesse maximum (cycles par seconde)
Poids
Capacité de projectiles par magasin
Dimensions de l’outil: hauteur
Dimensions de l’outil: longueur
Dimensions de l’outil: largeur: corps de
60–95 psi
.77 scfm
1
/4 in. NPT
15 (Sencomatic)
2.0 lbs.
110-185
5 15/16 in.
9 1/2 in.
1 15/16 in.
Español
Especificaciones Tecnicas
Presión de operación mínima y máxima
Consumo de aire (60 ciclos por minuto)
Entrada de aire
Velocidad máxima (ciclos por segundo)
Peso
Capacidad de grapas por cargador
Tamaño de la herramienta: Altura
Tamaño de la herramienta: Longitud
Tamaño de la herramienta: Ancho (Cuerpo)
4,1–6,5 bar
21,8 liter
1
/4 in. NPT
15 (Sencomatic)
0,9 kg
110-185
151 mm
241 mm
49 mm
4,1–6,5 bar
21,8 liter
1
/4 in. NPT
15 (Sencomatic)
0,9 kg
110-185
151 mm
241 mm
49 mm
60–95 psi
.77 scfm
1
/4 in. NPT
15 (Sencomatic)
2.0 lbs.
110-185
5 15/16 in.
9 1/2 in.
1 15/16 in.
8
4,1–6,5 bar
21,8 liter
1
/4 in. NPT
15 (Sencomatic)
0,9 kg
110-185
151 mm
241 mm
49 mm
60–95 psi
.77 scfm
1
/4 in. NPT
15 (Sencomatic)
2.0 lbs.
110-185
5 15/16 in.
9 1/2 in.
1 15/16 in.
Specifications
Especificaciones
Specifications
English
Español
Français
Tool: 1D0001N
Tool: 1D0041N
Tool: 1D0061N
.036"
,91mm
1/2"
13 mm
A
.0275"
,70 mm
A
Tool: 1D0001N
Tool: 1D0021N
Tool: 1D0031N
Tool: 1D0051N
9
Code
AT04
AT05
AT06
AT08
AT09
AT10
inches
1
/4
5
/16
3
/8
15
/32
9
/16
5
/8
mm
6
8
10
12
14
16
Limited Warranty
SENCO® Pneumatic, DuraSpin®, Cordless Tools
& Compressors
Senco Products, Inc. (“SENCO”) designs and constructs its products using the highest standards of material and workmanship. SENCO warrants to the original retail purchaser that the following products will be free from defects in material or workmanship for the warranty period
specified below:
SENCO® XP Series
Five years
SENCO DuraSpin®
One year
SENCO PRO Series
One year
SENCO Cordless
Two years
SENCO Compressors
One year
SENCO Reconditioned Products
One Year
During the warranty period (which begins on the purchase date), SENCO will repair or replace, at SENCO’s option and expense, any product or part that is defective in
materials or workmanship after examination by a SENCO Authorized Warranty Service Center, subject to the exceptions, exclusions and limitations described below. Any
replacement product or part will carry a warranty for the balance of the warranty period applicable to the replaced product or part. A DATED SALES RECEIPT OR PROOF
OF PURCHASE FROM THE ORIGINAL RETAIL PURCHASER IS REQUIRED TO MAKE A WARRANTY CLAIM. Warranty registration also is required and can be accomplished through on-line Product Registration at www.senco.com or by completing and returning the postage paid warranty registration form included with your Operator’s
manual/parts chart information, found inside the product carton. To make a warranty claim, you must return the product, with proper receipt/proof of purchase and return
transportation charges prepaid, to a SENCO Authorized Warranty Service Center. A list of SENCO Authorized Warranty Service Centers can be found at www.senco.com
or by calling 1-800-543-4596 toll free. SENCO will perform its obligations under this warranty, within a reasonable time after approval of the warranty claim.
Wheelbarrow Compressors:
1.
2.
Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the compressor pump will be free from defects in materials and workmanship for two years after the purchase date.
Defective parts of the compressor pump not subject to normal wear and tear will be repaired or replaced, at SENCO’s option, during the two year
warranty period. If SENCO determines that repair or replacement is not feasible, SENCO will refund the purchase price less reasonable depreciation based on actual use.
SENCO Cordless:
1.
2.
Subject to the exceptions, exclusions and limitations described below, SENCO warrants that the SENCO Cordless tool will be free from defects in
materials and workmanship for two years after the purchase date.
SENCO warrants that the batteries and chargers used with SENCO Cordless tools will be free from defects in material and workmanship for one
year after the purchase date.
WARRANTY EXCLUSIONS
The following warranty exclusions apply:
1. Normal wear parts are not covered under this warranty. Normal wear parts include, for example, isolators, drive belts, air filters, rubber o-rings,
seals, driver blades, piston stops, and piston/driver assembly.
2. This warranty does not cover parts damaged due to normal wear, misapplication, misuse, accidents, operation at other than recommended speeds
or voltage (electric units only), improper storage, or damage resulting during shipping.
3. Products used in production/industrial applications as defined by SENCO are excluded from this warranty.
4. Labor charges or loss or damage resulting from improper operation, maintenance or repairs are not covered by this warranty.
5. SENCO does not warrant the Wheelbarrow Compressor Engine/Motor, but the Compressor Engine/Motor may be covered under a warranty offered
by its manufacturer.
GENERAL WARRANTY CONDITIONS
This warranty will be honored, only if:
A. Clean, dry, regulated compressed air has been used, at air pressure not exceeding the maximum indicated on the tool casting;
B. No evidence of abuse, abnormal conditions, accident, neglect, misuse or improper modifications or storage of the product; and
C. No Deviation from operating instructions, specifications, and maintenance schedules exists (read Operator Manual for use, specifications, and
maintenance instructions).
THIS WARRANTY IS THE ONLY WARRANTY ON THE PRODUCT, AND SENCO DISCLAIMS ALL OTHER WARRANTIES. ANY IMPLIED WARRANTIES WILL BE LIMITED IN DURATION TO THE APPLICABLE WARRANTY PERIOD SPECIFIED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. YOUR REMEDIES ARE SOLELY AND EXCLUSIVELY AS STATED ABOVE. SENCO
SHALL IN NO EVENT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, OR SPECIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. IN NO EVENT, WHETHER
AS A RESULT OF A BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING NEGLIGENCE) OR OTHERWISE, SHALL SENCO’S LIABILITY EXCEED THE PRICE
OF THE PRODUCT WHICH HAS GIVEN RISE TO THE CLAIM OR LIABILITY. ANY LIABILITY CONNECTED WITH THE USE OF THIS PRODUCT SHALL TERMINATE
UPON THE EXPIRATION OF THE WARRANTY PERIOD SPECIFIED ABOVE. NO EMPLOYEE OR REPRESENTATIVE OF SENCO OR ANY DISTRIBUTOR OR DEALER
IS AUTHORIZED TO MAKE ANY CHANGE OR MODIFICATION TO THIS WARRANTY.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
REPLACEMENT OF TOOL DUE TO NATURAL DISASTER
SENCO will replace any tool destroyed by an Act of God such as flood, earthquake, hurricane or other disaster resulting only from the forces of nature. Such a
claim will be honored provided that such original retail purchaser had previously submitted a completed warranty registration card for the tool, and then submits
proof of ownership and an acceptable statement describing such Act of God documented by an insurance carrier, police department, or other official governmental
source. To obtain instructions for filing a claim call 1-800-543-4596.
CUSTOMER SATISFACTION
One hundred percent customer satisfaction is our #1 goal. If for any reason the product does not perform to the original purchaser’s satisfaction, it can be returned
to the place of purchase within thirty days with dated sales receipt for a full refund of the purchase price.
© 2006 by SENCO PRODUCTS, INC.
CINCINNATI, OHIO 45244-1611 USA
www.senco.com
070101