USER MANUAL
M-HPB30.B
M-HPB30.W
Table of contents
EN
Warranty
Safety information
Specifications
Product overview
Charge the battery
Switch On/Off
Pairing and connecting with a Bluetooth device
Re-connecting with a Bluetooth device
Adjust the Volume
Manage phone calls
Listen to music
Auxiliary input
Micro USB input
Product care
-2-
3
3
3
4
5
5
6
6
6
7
7
8
8
8
EN
Warranty
Thank you for purchasing this Macrom product. Should your product
need warranty service, please return it to the shop where you buy it or
to the Macrom distributor in your country . The warranty does not cover
damage due to improper use and or installation, incorrect connections to
power supply and audio video sources, exposure to excessive humidity,
unauthorized repair attempts or modifications.
Safety information
To prevent hearing damage when listening the headphones gradually
turn up the volume until you reach a pleasant and safe listening level.
Pay attention to do not use the headphones when your full attention to your
surroundings is required. For example is not safe (or even illegal in some
countries) to use headphones while driving a vehicle or crossing a street.
Specifications
M-HPB30 can make and receive calls hands-free with compatible mobile
phones and listen to music from a compatible music players. The
operating range is within 10 meters. M-HPB30 is compliant with the
following Bluetooth® specifications: Bluetooth V4.0 and supports HSP,
HFP, A2DP and AVRCP profiles. Power supply input 5V DC - 0.5 A.
-3-
EN
Product overview
Size adjustment.
Track forward
Pause/Play
MFB (Multi function button)
Track back
Volume up
Volume down
USB micro connector
Status indicator LED
Auxiliary input
-4-
EN
Charge the battery
Use the Micro USB cable provided with the
product to charge the battery. Plug it in the
connector located under the rigth ear cup of
the headphone, then plug the other end into a
compatible USB charger or a USB port of a
computer. The status indicator LED is steady
red while charging or steady blue if the battery
is fully charged. For a faster charge please
remember to power off the headphone before
charging the battery. The fully charged battery
allows up to 16 hours of continuous music
playback or phone calls. The maximum standby
time is approximately 100 hours. Is possible to
listen to music and/or make phone calls while
charging the battery. If the battery needs to be
charged the headphone will prompt a three
tones every 30 seconds and the status indicator
LED flashes red.
Switch On/Off
To switch ON, press and hold the MFB
key about 3 seconds until the headphone
prompts 4 ascending tones and the status
indicator LED blinks blue.
To switch OFF, press and hold the MFB
key about 3 seconds until the headphone
prompts 4 descending tones and the status
indicator LED switch off.
-5-
EN
Pairing and connecting with a Bluetooth device
To enter pairing mode, make sure the headphone is powered off then
press and hold the MFB key about 6 seconds until the headphone prompts
4 ascending tones and after a while 2 more tones and the status indicator
LED blinks red and blue alternately. From the Bluetooth function of the
device to be paired search for new device named “M-HPB30”. Select it and if
requested enter “0000” passcode. When pairing is completed successfully
the indicator LED blinks blue and the headphone prompts two tones. If
the pairing procedure is not successful, please switch off the headphone
and repeat the above steps. The specific pairing procedure may vary, so
please refer to your device user manual for further information. When in
pairing mode, if no device is paired within 2 minutes, the headphone will
return to standby mode automatically.
Re-connecting with a Bluetooth device
Every time the headphone is switched on, it will connect to the last
connected device automatically. When the headphone is in standby mode
and doesn’t connect to any HFP devices, short press MFB button once, it
will connect to last connected source device automatically.
Adjust the Volume
To adjust the headphone volume during a call
or while listening to music press the volume
up or down keys. When the volume is turned
to maximum or minimal levels, one tone is
prompted. Please remember that excessive
sound pressure from headphones can damage
your hearing.
-6-
To receive a phone call from the mobile phone use it
as usual. To manage the phone from the headphone
refer to the commands below:
Pick up a call: Short press MFB key when the
phone rings.
Reject a call: Press and hold MFB key for 2
seconds.
Hung up a call: Short press MFB key once.
Swap call audio: Press and hold MFB key for 2
seconds.
Microphone mute/un-mute: Short press MFB key
twice.
Redial the last number: Short press MFB key twice.
Take an incoming call dropping the first one: Short press
key once.
key twice.
Reject an incoming call keeping the first one: Short press
Switch calls: Press and hold
key for 2 seconds.
Hung up current mutiple calls: Short press
key once or twice to keep
second call active.
With some mobile phones, if an incoming call is accepted using the phone
commands the conversation will be automatically transferred to the
phone. To transfer it back to the headphone use the audio source switch
of the phone. Refer to the phone user manual for further information.
Listen to music
Connect the headphone to a compatible music
player that supports A2DP profile. Please note
that the music functions available depends on
your music player. If a call is received or originated
while listening to music, the music will be paused
until the call ends. To manage music from the
headphone refer to the commands below:
Pause/Play: Short press
key.
Track back: Short press ◄ key.
Track forward: Short press ► key.
Fast back: Press and hold ► key.
Fast forward: Press and hold ◄ key.
-7-
EN
Manage phone calls
EN
Auxiliary input
To connect a device to the auxiliary input use the cable provided with the
unit. If a connector is plugged in the auxiliary input the Bluetooth function
is automatically disabled. Bluetooth functions is automatically resumed
when the connector is removed from the auxiliary input.
Micro USB input
To listen music from a computer, use the micro USB cable provided with
the headphone. Plug it in the micro USB connector located under the rigth
ear cup of the headphone, then plug the other end into an USB port of
a computer. When the headphone is plugged to computer the Bluetooth
function is automatically disabled. Bluetooth functions is automatically
resumed when the micro USB cable is removed from the micro USB
connector. If the automatically reconnection does not work, please switch
off the headphone and repeat the pairing procedure.
Product care
Please remember that your Macrom product is an electronic device, and
so needs to be treated with care:
Do not subject it to mechanical shock or vibrations.
Do not subject it to eccessive heat.
Keep it away from water and excessively humid areas.
Keep it away from high electromagnetic fields.
There are no user-serviceable parts inside. Opening the product or try to
repair it will terminate the warranty.
-8-
The BLUETOOTH ® worldmark and logos are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by ALDINET
S.p.A. is under license.
The MACROM brand is a registered trademark of ALDINET S.p.A.
Declaration of Conformity
ALDINET S.p.A
Viale C. Colombo, 8 - 20090 Trezzano s/N (MI) - Itlaly
Tel. +39 02 484781
w
w
w
.
m
a
c
r
o
m
.
i
t