ADEMCO | LYNXR | Setup guide | ADEMCO LYNXR Setup guide

K14117
3/06 Rev. A
ADEMCO LYNXR-I
Security Systems
Quick Start Guide
UL
LYNXR-I is not intended for UL985 Household Fire applications unless a 24-hour backup battery (P/N
LYNXRCHKIT-HC or LYNXRCHKIT-SHA) is installed.
Introduction
This Quick Start Guide can help you install the rechargeable LYNXR-I quickly and easily by providing the basic
steps for installation using the built-in defaults. For more detailed information and important notes, refer to the
LYNXR-I Installation and Setup Guide.
The following steps assume that one of the system’s default tables will be used.
For programming data values and Powerline Carrier Devices other than those listed in the default tables, see the
Installation Instructions.
Default Table Summary
Zone
Table 1
Table 2
Table 3
Table 4
2
front door
front door
front door
3
back door
back door
back door
back door
4
window
garage door
window
window
5
motion detector
motion detector
window
window
6
-------
smoke detector
window
window
7
-------
-------
window
window
8
-------
-------
motion detector
motion detector
9
-------
-------
smoke detector
smoke detector
26
loop 3 arm away
loop 3 arm away
loop 3 arm away
loop 3 arm away
27
loop 2 disarm
loop 2 disarm
loop 2 disarm
loop 2 disarm
28
loop 4 arm stay
loop 4 arm stay
loop 4 close device
loop 4 close device
29
loop 1 no alarm response
loop 1 no alarm response
loop 1 no alarm response
loop 1 no alarm response
30
loop 3 arm away
loop 3 arm away
loop 3 arm away
loop 3 arm away
31
loop 2 disarm
loop 2 disarm
loop 2 disarm
loop 2 disarm
32
loop 4 arm stay
loop 4 arm stay
loop 4 close device
loop 4 close device
33
loop 1 no alarm response
loop 1 no alarm response
loop 1 no alarm response
loop 1 no alarm response
92
duress
duress
duress
duress
silent alarm
1-2-3-4
4-1-1-2
------
audible alarm
1-2-3-4
4-1-1-2
------
silent alarm
1-2-3-4
4-1-1-2
------
silent alarm
1-2-3-4
4-1-1-2
------
99
Master User Code
Installer Code
Duress Code
front door
Entering Expert Program Mode: installer code + 8 0 0
Interactive Mode
*56 Enhanced Zone Programming
Used to Program
Zone characteristics, report codes, and serial numbers
*83 Enhanced Sequential Mode
5800 Series transmitter serial numbers
*84 Assign Zone Voice Descriptors
Voice descriptors for each zone
Exiting Program Mode: *98 inhibits re-entry into the Programming mode using the Installer Code.
*99 allows re-entry into the Program mode using Installer Code + 8 0 0.
NOTES:
• Table 4 supports the automatic paging feature (open/close events reported to pager phone number),and a Powerline Carrier Device programmed
as device 8, which closes and stays closed upon burglary alarms and restores after bell timeout. For other applications or actions (e.g., using a
pulsing siren), see the *80 Device Programming Menu Mode section of the Installation Instructions.
• Primary and secondary report format for all tables is Ademco’s Contact ID® reporting.
• Tables 1, 3 and 4 record only alarms, alarm restores, troubles, and trouble restores in the event log. Table 2 records all events in the event log.
Installing LYNXR-I
Installation and Electrical Connections
Step
1.
2.
3.
Action
Install the control as follows:
a. Separate the front assembly from the back plate and disconnect the cable from the front assembly board.
Note: Disconnect the cable only from the front assembly board, not from the terminal block PC board.
b. Mount the back plate.
Make wiring connections as follows:
a. Connect the incoming phone line to either the 8-position jack or terminals 2 (TIP) and 3 (RING).
b. Connect the handset phone lines to either the RJ11 jack or terminals 4 (TIP) and 5 (RING).
Note: For full line seize operation, see the installation instructions.
c. If used, connect a piezo sounder to terminals 10 (+) and 11 (–).
d. If used, connect a bell to terminals 11 (–) and 12 (+).
e. If using Powerline Carrier Devices, connect com/data/sync/ lines from the K10145X10 transformer to terminals
9, 13, and 14 respectively.
Note: Install Powerline Carrier Devices according to their instructions.
f. Connect wires from the K10145X10 (K101450CN) AC Transformer to terminals 15 and 16.
Make battery connections as follows:
a. Remove battery retainer.
b. Remove backing from tape on back plate.
c. Insert battery pack into back plate.
d. Install battery retainer.
e. Connect battery connector to receptacle on terminal block PC board.
f. Carefully reconnect the ribbon cable to the front assembly PC board connector (properly aligning the red wire).
g. After all wiring connections have been made, snap the front assembly to the back plate so it is held by the
locking tabs.
h. Plug the transformer into a 24-hour, 110VAC unswitched outlet.
Note: Rechargeable batteries may take up to 48-hours to fully charge. “LOW BAT” message should clear within four
hours, or by entering Test Mode.
RETAINER
NOTE
LYNXRCHKIT-HC
BATTERY PACK SHOWN
BATTERY
PACK
TAPE
BATTERY
RECEPTACLE
WIRING
TERMINALS
-2-
07000-007-V0
UL NOTE
THE MINIMUM WIRE SIZE USED FOR TELEPHONE
INSTALLATIONS MUST BE #26 GAUGE
INCOMING
PHONE
LINE
EARTH
GROUND
8
POS
JACK
1
FUTURE
USE
PHONE
2
3
4
5
6
8
7
( )
TIP RING TIP RING
GND
DATA IN
WARNING:
TO PREVENT
RISK OF SHOCK
DISCONNECT
TELEPHONE LINE
AT TELECOM
JACK BEFORE
SERVICING
THIS UNIT.
GND
SOUNDERS
9
10
11
12
( )
(+)
( )
(+)
PLCD
13
14
AC
15
16
DATA SYNC
OUT IN
POWERLINE
CARRIER DEVICES
RJ11
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
DATA OUT
TO
HANDSET
PHONE
LINE
INTERNAL 7845i-L*
MODULE ONLY
STANDARD/HIGH
CAPACITY BATTERY
CONNECTOR
SUPER HIGH CAPACITY
BATTERY CONNECTOR
ALARMNET LRR/IP
COMMUNICATIONS PORT
INCOMING
TELEPHONE
LINE
PREMISES
TELEPHONE
PIEZO
BELL
EARTH
GROUND
FUTURE
USE
LOCAL SOUNDER DISABLE
SHUNT REMOVE TO DISABLE
THE LYNXR-I CONTROL IS COMPATIBLE WITH
THE FOLLOWING INTEGRAL RECHARGEABLE
BATTERY PACKS:
P/N LYNXRCHKIT-SC
P/N LYNXRCHKIT-HC
P/N LYNXRCHKIT-SHA
REPLACE EVERY FOUR YEARS
WEEKLY TESTING IS
REQUIRED TO ENSURE
PROPER OPERATION
OF THIS SYSTEM
6-14VDC
30mA max.
6-14VDC
120mA max.
(e.g. WAVE2EX)
K10145X10
PLUG-IN
TRANSFORMER
9VAC, 25VA
AC
AC
SYNC
COM
DATA
NOTE
USE ONLY THE K10145X10
OR K10145CN
TRANSFORMERS PROVIDED
* WHEN AVAILBLE
X10
ONLY
CONNECTIONS
07000-009-V1
LYNXR-I WIRING CONNECTIONS
System Programming
Step
1.
2.
Action
Set a programming default as follows:
a. Enter Programming mode: Installer Code + 8 0 0.
b. Press *97, then press a number 1-4 to select a default table from the tables listed on page 1.
Program the variable data fields as follows:
a. RF House ID - Press *24, then enter the desired 2-digit RF House ID for wireless keypads.
b. PABX Access Code (if used) - Press *40, then enter up to 6 digits. If fewer than 6 digits are used, press [*]
to end the field and advance to the next field.
c. Primary Phone Number - Press *41, then enter the primary phone number, up to 20 digits. If fewer than 20
digits are used, press [*] to end the field and advance to the next field.
d. Secondary Phone Number (if used ) - Press *42, then enter the secondary phone number, up to 24 digits. If
fewer than 24 digits are used, press [*] to end the field and advance to the next field.
e. Secondary Account Number (if used) - Press *44, then enter the secondary account number. If only 3 digits
are used, press [*] to end the field and advance to the next field.
f. Primary Account Number (if used) - Press *43, then enter the primary account number. If only 3 digits are
used, press [*] to end the field and advance to the next field.
g. Pager Characters - Press *88 if using Default Table 4, then enter up to 16 digits which may be required by
your pager service (e.g. account number, PIN, etc.). If fewer than 16 digits are used, press [*] to end the field
and advance to the next field.
h. Download Phone Number - Press *94, then enter the downloading computer phone number, up to 20
digits. If fewer than 20 digits are used, press [*] to end the field.
-3-
Step
3.
Action
Enhanced Sequential Mode - Press *83, then follow the prompts as follows:
Zone Number - Enter 2-digit zone number of the first transmitter to have its serial number
entered. The system will announce the Voice Descriptor for the selected zone number, if it is
programmed.
Press [*] to continue. Starting with this zone, the system will search for the first transmitter,
which has all of the following attributes pre-programmed in Zone Programming.
1) The correct input type selected in *56 (RF, UR, or BR programmed)
2) The correct loop number selected in *56
3) No serial number programmed
4) Zone type
Notes: 1. If the first zone number entered does not have one or more of the above attributes, the system will
search its database for the first zone that does, and will display it at the ENROLL SERIAL NUMBER
prompt (1b).
2. Pressing 00 exits mode, upon which the prompt “83” blinks, indicating the mode is inactive.
A
01
1A zz
1A LC
Note:
a.
b.
Enroll Mode - If “L” is displayed, the serial number for this transmitter has already been entered,
however, it may still be confirmed, viewed or deleted.
1) If the transmitter’s serial number has not been previously entered, enter the enroll serial
number mode now by pressing “1”, or copy the last serial number that was entered by
pressing “2”.
2)
If the transmitter’s serial number has been previously entered, it may be viewed by pressing
“3” or deleted by pressing “9”.
If view is selected; each digit will be re-displayed, and the keypad will beep once for digits 1-6, and three
times for the last digit.
3)
Note:
Note:
1b zz
Note:
1b
Once the serial number has been entered the system will return to the (1A) prompt and “L”
will be displayed.
This point can be faulted and restored and the panel will listen for the transmission.
4) The serial number/loop number combination that was entered can be confirmed by faulting
and restoring the zone being entered. If the panel receives a transmission that matches the
serial number and loop number entered, the keypad will beep three times, and “C” will be
displayed. This indicates that the serial number transmission has been confirmed to match.
No further transmissions will be received.
When confirming a 4-button key, it assumed that all loops are used and only the serial number is
confirmed. Pressing any key will allow a confirm. Two beeps indicate that the template has been
accepted. A single long beep indicates illegal entries, or duplicate serial number/loop entry.
5) When the last zone has been entered, the display will remain on that zone. To exit this mode
and return to data field program mode, press 00 at the ZONE NUMBER prompt
6) Once all zones have been programmed, test each zone using the system’s Test mode. Do
not use the Transmitter ID Sniffer mode for this, since it will only check for transmission of
one zone on a particular transmitter, and not the zones assigned to each additional loop.
c.
Serial Number - This prompt can be used to enroll the transmitter serial number via RF
transmission or manually. If using RF Learning proceed to c. 1). If using the manual mode skip to
c. 2).
1) RF Learning - Two (2) transmissions (two key depressions at least five second apart) will be
required for BR type or four (4) transmissions (fault, restore and fault, restore) for UR or RF
type. BR type devices can be enrolled only by transmission from BR devices. Likewise, UR
and RF devices can only be enrolled by transmission from a UR or RF device.
If the learned serial number has a different loop number than that entered in *56 the system
will announce the Voice Descriptor, if it is programmed, followed by two beeps and will return
to Prompt (1A) and “L” will be displayed.
If the loop number captured by RF transmission and that entered in *56 mode match, the
system will announce the Voice Descriptor, if it is programmed, followed by three beeps and
return to Prompt (1A) and “LC” will be displayed. No additional transmissions are needed for
confirmation.
BR type devices can be enrolled only by transmission from BR devices. Likewise, UR and RF devices
can only be enrolled by transmission from a UR or RF device.
2) Manual Entry - Enter the 7-digit serial number printed on the transmitter. If you enter an
incorrect digit, press the [#] key to backup to prompt (1A) and start over. When all seven
digits are entered press the [*] key.
-4-
Step
3.
Action
Once all 7 digits have been entered, press the [*] key. If less than 7 digits are entered,
(Cont.)
the keypad will emit a single long beep and return to the (1A) prompt without displaying
the “L”. If more than 7 digits have been entered, the first 6 digits will be saved along with
the last digit that was entered (entering 123456789 yields the serial number 1234569).
Note: If 52 seconds passes and no entry has been made, the system returns to prompt (1A).
3)
d.
Delete Serial Number - This prompt can be used to delete the serial number programmed for the
zone.
1) Enter “0” to discard delete request or “1” to confirm
Set RF House ID in the wireless keypads as follows:
a. 5827 wireless keypad - Set the keypad’s DIP switches to the RF House ID programmed in field *24.
b. 5804BD button key - Set the RF House ID per its instructions.
c. Powerline Carrier Devices - Set their House ID to “A,” (programmed as “0”) or use field *25 to change the ID
to avoid conflicts with existing installations.
Set the Real-Time Clock as follows:
a. Enter time/date setting mode by entering the User Code + FUNCTION + [63].
b. The hour prompt is displayed. Enter the correct hour, then press [ADD] to accept and advance.
c. For each subsequent prompt, enter the correct value, then press [ADD].
d. The system will exit this mode automatically after entering the year and pressing [ADD], or if no keys are
pressed for 1 minute.
Install Wireless Devices:
a. Before permanently mounting the wireless devices, enter Installer Code + [#] + [8] and run the Go/No Go
test. This will ensure adequate signal strength from each location.
b. Fault each transmitter to ensure all programmed zones are received.
c. Mount the transmitter in its permanent location.
Test the system as follows:
a. After installation and programming, enter Installer Code + TEST.
b. To exit Test mode, enter Installer Code + OFF.
Assign desired User Codes by following the procedures in the User Guide. Show the user how to perform the
various system functions.
Perform site-initiated downloader session (to load central station ID) by Installer Code + [#] + [1].
F
4.
5.
6.
7.
8.
9.
5800 Series Transmitter Loop Numbers
The following illustration shows the compatible transmitters and their associated input types and loop designations.
UL
The 5800RL, 5802MN, 5802MN2, 5804, 5804BD, 5804BDV, 5804E, 5814, 5816TEMP, 5819, 5819S(WHS & BRS),
5828/5828V and 5850(GBD) wireless transmitters have not been evaluated by UL.
LOOP 3
LOOP 3
LOOP 4
YOU MUST
ENROLL
THIS
BUTTON
LOOP 4
YOU MUST
ENROLL
THIS
BUTTON
LOOP 2
LOOP
1
LOOP 1
LOOP
1
ON
LOOP 2
LOOP 4
YOU MUST
ENROLL
THIS BUTTON
LOOP 2
OFF
LOOP 1
LOOP 3
••
•
••
•
•• •
••• ••••
• ••
5 8 0 0 WAV E
P RO G R A M
HOUSE ID
5800RL
SET
HOUSE ID
5801
ENROLL AS
"UR" OR "RF"
LOOP 1
LOOP 1
LOOP 2
(REED)
LOOP 1
(TERMINALS)
LOOP 1
(TERMINALS)
LOOP 1
(TEMP
SENSOR)
ALTERNATE
POSITION
FOR LOOP 2
5809
ENROLL AS "RF"
5806/5807/5808/5808LST
ENROLL AS "RF"
5814
ENROLL AS "RF"
LOOP 2
(REED)
LOOP 2
(REED)
5816
ENROLL AS "RF"
5 8 0 4 B D / 5 8 0 4 B DV
ENROLL AS "BR"
PROGRAM HOUSE ID
LOOP 1
(PRIMARY)
LOOP 2
(REED)
LOOP 1
5804/5804E
ENROLL AS "BR"
5802 MN2
ENROLL AS
"UR" OR "RF"
5802 MN
ENROLL AS
"UR" OR "RF"
LOOP 1
5816MN
ENROLL AS "RF"
5816TEMP
ENROLL AS "RF"
LOOP 2
(AUX.
CENTER)
LOOP 3
(AUX.
RIGHT)
5817
ENROLL AS "RF"
AR
ME
D
RE
AD
Y
MIC
LOOP 3
(TERMINALS)
LOOP 1
LOOP 3
(TERMINALS)
5818
ENROLL AS "RF"
LOOP 1
(TERMINALS)
5819
ENROLL AS "RF"
MESS
AGE
LOOP 1
(INTERNAL
SHOCK
SENSOR
5819S (WHS & BRS)
ENROLL AS "RF"
LOOP 1
(SOUND)
LOOP 1
(MOTION)
(G
ree
(Re n)
d)
(Ye
5828/5828V
PROGRAM
HOUSE ID
5849
ENROLL AS "RF"
llow
)
5850 (GBD)
ENROLL AS "RF"
5890/5890PI
ENROLL AS "RF"
01009-012-V4
Notes: (1) Loop 4 must always be enrolled on the 5801, 5804, 5804BD, 5804BDV, and 5804E transmitters.
(2) 5804E encrypted (High-Security) devices must be activated while the system is in Go/No Go Test Mode. Refer to the
transmitter’s installation instructions for complete details. The system will confirm enrollment of the encrypted device by beeping
two times.
-5-
Keypad Functions (when default programming is used)
Security Functions
Checking system status: STATUS (high level messages); press STATUS
again for secondary messages.
To arm in STAY mode: Press and hold down STAY (or enter your code + STAY ) See note below.
To restart exit delay: STAY (applies only if system is armed in Stay mode and Quick Exit option has been enabled)
To arm in AWAY mode: Press and hold down AWAY (or enter your code + AWAY ) See note below.
To arm with NO DELAY: Press and hold down AWAY or STAY + NO DELAY or enter your user code + the keys shown).
To disarm the system and silence alarms: User Code + OFF
See note below.
To bypass a zone(s): User Code + BYPASS + 2-digit zone number(s)
To turn Chime mode on or off: FUNCTION + CHIME
Message Center
To record a message: FUNCTION +
RECORD
To stop recording before end of 20 seconds: OFF
To play back a message: FUNCTION +
PLAY
To skip a message: [✻]
To delete all messages: FUNCTION +
DELETE
(during message replay)
Volume Control
To adjust message playback/system announcement volume: FUNCTION +
To mute system announcements: FUNCTION +
VOLUME
+
To restore/unmute announcements & volume: FUNCTION +
VOLUME + [3] (Up) or [6] (Down)
OFF
VOLUME + [3] or [6]
Note: If the system was muted during Field Programming it will be unmuted upon exiting.
Other Functions
To set the time and date: User Code + FUNCTION + [63]
To activate or deactivate X10 devices 1-6: FUNCTION + LIGHTS ON or LIGHTS OFF + device number
To activate or deactivate X10 devices 7 & 8: User Code + [#] + LIGHTS ON or LIGHTS OFF + dev. no.
To program scheduled events: User Code + FUNCTION + [64], then follow procedure in User Manual.
To add a User Code: Master Code + CODE + user number + User’s Code (see note below)
To delete a User Code (except Master Code): Master Code + CODE + user number
To turn Test mode on: User Code + TEST
To turn Test mode off: User Code +
OFF
To use the defined AUX function: Press and hold AUX key 2 secs (4 beeps) + User Code
(To define the AUX function, refer to the procedure in the Aux Function section of the User Manual. Note: The 1-button
paging feature [field *87] is not enabled with the default programming)
To program Follow Me announcement telephone number: User Code + FUNCTION + [65]
-6-
Remote Phone Control Operation
To remotely disarm system:
+ [1]
+ [2]
To remotely arm in AWAY mode:
To remotely arm in STAY mode:
+ [3]
+ [2] or [3] + [0]
To remotely arm in AWAY or STAY with NO DELAY:
To remotely activate X10 devices 1-6: [#] + [4] + device no.
+ [#] + [4] + device no.
To remotely activate X10 devices 7 & 8:
To remotely deactivate X10 devices 1-6: [#] + [7] + device no.
+ [#] + [7] + device no.
To remotely deactivate X10 devices 7 & 8:
To remotely bypass a zone:
+ [6] + zone no.
To remotely activate forced bypass:
+ [6] + [#]
Note: Force bypass option must be enabled.
To remotely check system status: [*]
+ [9]
To end remote phone session: Hang up or
Speaker Phone Operation
(Note: The ARMED and READY LEDs blink alternately when the Speaker Phone feature is active)
To place a call or answer a call using the speaker phone: [#] + AUX
To Flash (switch between two calls using call waiting): AUX
To hang up and exit speaker phone mode: OFF
To enable/disable (toggle) ringer: [#] + VOLUME
+ AUX
To return the keypad to telephone mode after disarming the system: [#] + AUX
Note: The Babysitter Code and Installer Code cannot disarm the system unless it was the code used to arm the system.
In addition, if the system is armed by pressing and holding the Quick-Arm buttons, neither the Babysitter Code nor
the Installer Code can disarm the system.
REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE LIMITATIONS OF THIS SYSTEM AND
WARRANTY INFORMATION.
-7-
‡K141170Š
K14117
3/06 Rev. A
165 Eileen Way, Syosset, New York 11791
Copyright © 2006 Honeywell International Inc.
www.honeywell.com/security
Download PDF

advertising