User guide | 3Com 100 PCI Network Card User Manual

SuperStack® 3 Baseline 10/100 Switch 24-Port 10BASE-T/100BASE-TX
plus 1-Port 1000BASE-T (3C16467) User Guide
DUA1646-7AAA02
INTRODUCTION
The SuperStack ® 3 Baseline 10/100 Switch 24 Port
10BASE-T/100BASE-TX plus 1-Port 1000BASE-T is a versatile,
easy-to-use unmanaged switch. It is ideal for users who want the
high-speed performance of 10/100 switching with the added
functionality of a 1000BASE-T link but do not need sophisticated
management capabilities. The Baseline 10/100 Switch is shipped
ready for use. No configuration is necessary.
The Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T provides high performance switched
connections to 10Mbps and 100Mbps hubs, servers and
workstations that need a dedicated switched link and a switched
fixed speed 1000 Mbps port that can connect to other
1000BASE-T ports or servers/workstations.
The Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T has 24 shielded RJ-45, 10/100Mbps
auto-negotiating ports and one shielded RJ-45, 1000BASE-T port
on the front panel. Each 10/100Mbps port automatically
determines the speed and duplex mode of the connected
equipment and provides a suitable switched connection. The
1000BASE-T port is a fixed speed port that operates in full duplex
mode.
The Baseline 10/100 Switch is suited for office use where it can
be free standing, or rack mounted (in a wiring closet or
equipment room).
The Baseline 10/100 Switch comes with:
„
One power cord
„
Four self-adhesive rubber pads
„
One mounting kit
The Switch can be powered either from the AC mains supply, or
through an optional 3Com SuperStack 3 Advanced Redundant
Power System (3C16071B). Contact your supplier for details.
1
HOW TO USE THE BASELINE 10/100 SWITCH 24-PORT
The numbers in this diagram refer to numbered sections in the
text.
to either another 1000BASE-T switch port or to a 1000BASE-T
server or workstation without additional configuration.
Front Panel
Connecting to a Network Device
To connect a device to the Baseline 10/100 Switch 24 Port
10BASE-T/100BASE-TX plus 1-Port 1000BASE-T, use Category 5
unshielded or shielded (screened) 100 Ohm TP cable (or
Category 3 cable for a 10Mbps connection). The maximum length
of cable for each connection is 100m (328ft). Connect one end of
the cable to an RJ-45 port on the Baseline 10/100 Switch, and
the other end to the appropriate RJ-45 port on the connecting
device.
24 RJ-45 10/100 Ports and 1 RJ-45 1000 Port
WARNING: RJ-45 ports. These are shielded RJ-45 data
1
sockets. They cannot be used as telephone sockets. Only
connect RJ-45 data connectors to these sockets. Either
shielded or unshielded data cables with shielded or
unshielded jacks can be connected to these data sockets.
AVERTISSEMENT: Les ports RJ-45. Il s’agit de prises
femelles blindées de données RJ-45. Vous ne pouvez pas
les utiliser comme prise de téléphone. Branchez uniquement des connecteurs de données RJ-45 sur ces prises
femelles. Les câbles de données blindés ou non blindés,
avec les jacks blindés ou non blindés, l’un ou l’autre, peuvent être branchés à ces prises de courant de données.
WARNUNG: RJ-45-Anschlüsse. Dies sind abgeschirmte
RJ-45-Datenbuchsen. Sie können nicht als Telefonanschlußbuchsen verwendet werden. An diesen Buchsen
dürfen nur RJ-45-Datenstecker angeschlossen werden.
Diese Datenstecker können entweder mit abgeschirmten
oder unabgeschirmten Datenkabeln mit abgeschirmten
oder unabgeschirmten Klinkensteckern verbunden werden.
Connecting to another Switch or Hub
If you connect two Baseline 10/100 Switch 24 Port
10BASE-T/100BASE-TX plus 1-Port 1000BASE-T units
together, 3Com recommends that you use the
1000BASE-T ports on both units for the link. You must
use Category 5 cable when connecting the units.
1000BASE-T connection: To connect a Baseline 10/100 Switch
24 Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T to
another Switch using the 1000BASE-T port, use a normal ‘straight
through’ cable and connect each end to the 1000BASE-T port on
each unit.
100BASE-TX connection: To connect the Baseline 10/100 Switch
24 Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T to a
SuperStack 3 hub using a normal ‘straight through’ cable,
connect any port on the Baseline 10/100 Switch 24 Port
10BASE-T/100BASE-TX plus 1-Port 1000BASE-T to the MDI/MDIX
port on the hub, as shown below. Ensure that the MDI switch on
the hub is in (MDI).
10BASE-T/100BASE-TX Ports
The Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T has 24 10/100Mbps auto-negotiating ports.
Ports 1–23 are MDIX ports. Each can be connected to a device
with an MDI port (such as a workstation) using a normal ‘straight
through’ TP (twisted pair) cable. Alternatively, you can connect to
a device with MDIX ports using ‘cross-over’ TP cable.
Port 24 is ‘switch selectable’ MDI/MDIX using the MDI switch, as
described in 2. Using this port, you can connect to any other
device without the need for ‘cross-over’ cable.
Ports 1 to 24 are auto-negotiating: their speed and duplex mode
(half duplex or full duplex) are automatically determined by the
capabilities of the connected device. Each port can be connected
to either a 10BASE-T or a 100BASE-TX device.
!
CAUTION: The Baseline 10/100 Switch supports full
duplex auto-negotiation. If the connected device does not
support auto-negotiation, the Switch will operate in half
duplex mode (even if the device is operating in full duplex
mode). In such a configuration, you may notice some
degradation of network performance. 3Com recommends
that you use devices that are capable of auto-negotiation
(and that you ensure that auto-negotiation is enabled, if
it is a configurable option).
An alternative method of connecting the Baseline 10/100 Switch
to a hub using a normal ‘straight through’ cable is to connect any
MDIX port on the hub to the MDI/MDIX port on the Baseline
10/100 Switch, ensuring that its MDI Switch is set to in (MDI).
You can use ‘cross-over’ TP cable to connect any MDIX port on
the Baseline 10/100 Switch to any MDIX port on a hub.
1000BASE-T Port
Port 25 is a 1000BASE-T port capable of auto-negotiation with
the connected port to operate at 1000BASE-T full duplex. It
auto-senses an MDI/MDIX connection and can be used to connect
2
2
MDI Switch
Off The link has not been established. Either nothing is
connected to the port, or there is a problem:
This switch affects port 24 only:
Out
MDIX
In
MDI
3
■
Port 24 is an MDIX port.
It can be connected to a device with an MDI
port (such as a workstation) using a normal
‘straight through’ TP cable.
Port 24 is an MDI port.
It can be connected to an MDIX port on a
device (such as a hub) using a normal
‘straight through’ TP cable.
■
If the LED is off for port 24, check the setting of the
MDI switch. Refer to 2. Try toggling the MDI switch.
If the port is connected to another unit’s MDI/MDIX
port, check the other unit’s MDI switch position.
If these checks do not identify the cause of a problem, it may be that the unit or the device connected
to the port is faulty. Contact your supplier for further advice.
Display Function Switch
This switch affects the Status LEDs described in 4 and 5:
Out
In
4
„
This is the normal position of the switch.
The Status LEDs show the Activity and Link
Status of each port.
When the switch is pressed in, the Status
LEDs show the Duplex and Speed Status of
each port. The switch returns to the out position when released. This switch does not
affect port 25.
6
Activity/Duplex Status LEDs
Power/Self Test LED
The Power/Self test LED lights green when the unit is powered on
and ready for use.
Rear Panel Connections
7
Power Supply
The Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T automatically adjusts to the supply voltage.
Only use the power cord that is supplied with the unit.
On The port is operating in full duplex mode.
Off Ports 1 to 24: If the link is established, the port is
operating in half duplex mode.
Port 25: No link is present.
8 Socket for Redundant Power System (RPS)
Only connect a 3Com SuperStack 3 Advanced RPS (3C16070,
3C16071, 3C16071A or 3C16071B) to this socket. An
appropriate power module and cable is required. The connector
on the Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX
plus 1-Port 1000BASE-T is a Type 2 socket. For details, follow the
installation instructions in the guides that accompany the
Advanced RPS and the power module.
Link/Speed Status LEDs
The second and fourth (bottom) row of Status LEDs, which are
colored green, show the link or speed status of the related ports:
„
When the Display Function switch is pressed in, these LEDs
show the speed status of each port:
On Ports 1 to 24: The port is operating at 100Mbps.
Port 25: The port is operating at 1000 Mbps
Off Port 1 to 24: If the link is present, ports 1 to 24 are
operating at 10Mbps.
Port 25: The link has not been established.
The first (top) and third row of LEDs, which are colored yellow,
show the activity or duplex status of the related ports:
„ When the Display Function switch is out (its normal position),
these LEDs show the activity of each port. The LED flashes
when packets are received or transmitted on the port.
„ When the Display Function switch is pressed in, these LEDs
show the duplex status of each port:
5
Check that the attached device is powered on.
Check that the cable is the correct type and is not faulty.
When the Display Function switch is out (its normal position),
these LEDs show the link status of each port:
9
Self-adhesive Pads
The unit is supplied with four self-adhesive rubber pads.
On The link has been established and the segment
attached to the port is functional.
You do not need to apply the pads if you intend to rack
mount the unit.
If the unit is to be part of a free standing stack, apply the pads to
each marked corner area on the underside of the unit. Place the
unit on top of the lower unit, ensuring that the pads locate with
the recesses of the lower unit.
INSTALLATION RECOMMENDATIONS
Positioning the Switch
It is always good practice to wear an anti-static wrist
strap when installing network equipment, connected to a
ground point. If one is not available, try to keep in contact with a grounded rack and avoid touching the unit's
ports and connectors, if possible. Static discharge can
cause reliability problems in your equipment.
When deciding where to position the Baseline 10/100 Switch 24
Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T ensure:
„ It is accessible and cables can be connected easily.
„ Cabling is away from sources of electrical noise. These include
lift shafts, microwave ovens, and air conditioning units. Electromagnetic fields can interfere with the signals on copper
cabling and introduce errors, therefore slowing down your
network.
„ Water or moisture cannot enter the case of the unit.
„ Air flow around the unit and through the vents in the side of
the case is not restricted (3Com recommend that you provide
a minimum of 25mm (1in.) clearance).
„ The air is as free from dust as possible.
„ Temperature operating limits are not likely to be exceeded. It
is recommended that the unit is installed in a clean, air conditioned environment.
Rack Mounting or Free Standing
The unit can be mounted in a 19-inch equipment rack using the
Mounting Kit. Refer to “Mounting Kit Instructions” on page 4, or
it can be free standing. Do not place objects on top of the unit or
stack.
CAUTION: If installing the Baseline 10/100 Switch 24
Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T in a
free standing stack of different size SuperStack 3 units,
the smaller units must be installed above the larger ones.
Do not have a free standing stack of more than six units.
3
Power Supply
the Advanced Redundant Power System, ensure it is powered on.
Power problems can be the cause of serious failures and downtime in your network. Ensure that the power input to your system
is clean and free from sags and surges to avoid unforeseen network outages. We recommend that you install power conditioning, especially in areas prone to black outs, power dips and
electrical storms.
When the switch is powered on, the Power/Self Test LED should
first flash green, then stay lit. If it does not, refer to 6.
Spot Checks
At frequent intervals you should visually check the Baseline
10/100 Switch 24 Port 10BASE-T/100BASE-TX plus 1-Port
1000BASE-T. Regular checks can give you an early warning of a
possible failure; any problems can then be attended to when
there will be least effect on users. Check the following:
The unit is intended to be grounded. Ensure it is connected to
earth ground during normal use. Installing proper grounding helps
to avoid damage from lightning and power surges.
Power Up
Cabling
Use the following sequence to power up the Baseline 10/100
Switch 24 Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T:
„
Check the network connections and cables.
„
Connect the power supply cable to the appropriate power
socket on the rear panel of the unit; refer to 7 or 8.
„
Connect the plug to the power supply outlet socket and
switch on the power supply at the socket. If you are using
Cooling fans
Check that all external cabling connections are
secure and that no cables are pulled taut.
Where possible, check that the cooling fans are
operating by listening to the unit. The fans are
fitted near to the front right hand side of the
unit (when viewed from the front).
If you experience any problems operating the Baseline 10/100 Switch
24 Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T, refer to
“Problem Solving” on page 4.
MOUNTING KIT INSTRUCTIONS
Introduction
The Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T is supplied with two mounting brackets and
four screws. These are used for rack mounting the unit. When
mounting the unit, you should take note of the guidelines given
in “Positioning the Switch” on page 3.
3
Insert the two screws supplied in the mounting kit and fully
tighten with a suitable screwdriver.
4
Repeat the two previous steps for the other side of the unit.
5
Insert the unit into the 19-inch rack and secure with suitable
screws (not provided).
6
Reconnect all cables.
Rack Mounting the Units
The Baseline 10/100 Switch is 1U high and will fit a standard
19-inch rack.
CAUTION: Disconnect all cables from the unit before
continuing. Remove the self-adhesive pads from the
underside of unit, if already fitted.
1
Place the unit the right way up on a hard, flat surface with
the front facing towards you.
2
Locate a mounting bracket over the mounting holes on one
side of the unit.
PROBLEM SOLVING
Refer to the information about LEDs given earlier in this guide to
see if the problem can be identified and rectified. Here are some
common problems that can occur:
at a time, waiting a few seconds between each port. If the LEDs
go off after removing a port connection, the device that was
connected to that port is introducing an excessive amount of
broadcast frames to the network (some pieces of network
equipment operate by sending out broadcast frames regularly).
Refer to the documentation that accompanies the device for
information on disabling the broadcast operation.
Link Status LED not lit for a port that has a connection.
There is a problem with this connection. Check that:
„
„
„
„
„
The device being connected to is powered on and operating
correctly.
The cable is connected at both ends.
That you are using a TP cable that is:
■
‘Straight through’, to connect an MDIX port to an MDI
port.
■
‘Cross-over’, to connect an MDIX port to an MDIX port,
or an MDI port to an MDI port.
The cable is not damaged.
If the connection is to a workstation, that the workstation’s
network interface is installed and configured correctly.
If the problem persists and the unit still does not operate
successfully, contact your supplier with the following information
before returning the unit:
All Activity LEDs appear to be lit continually. There may be
broadcast storms on the network. Remove port connections one
4
„
Product number and serial number (printed on a label supplied with the unit)
„
A brief description of the fault
SAFETY INFORMATION
Please read the following safety information carefully before
installing the Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX
plus 1-Port 1000BASE-T.
unit must be powered by 230V (2P+T) via an isolation transformer ratio 1:1, with the
secondary connection point labelled Neutral, connected directly to earth (ground).
†
Impédance à la terre
Power Cord Set
This must be approved for the country where it will be used. e.g.
WARNING: Installation and removal of the unit must be carried out
by qualified personnel only.
„
„
„
„
„
„
„
U.S.A. and
Canada
If installing the Switch unit in a stack with SuperStack 3 Hub units, the
Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus 1-Port
1000BASE-T unit must be installed below the narrower Hub units.
The unit must be connected to an earthed (grounded) outlet to comply
with international safety standards.
Do not connect the unit to an A.C. outlet (power supply) without an
earth (ground) connection.
The appliance coupler (the connector to the unit and not the wall plug)
must have a configuration for mating with an EN60320/IEC320
appliance inlet.
The socket outlet must be near to the unit and easily accessible. You
can only remove power from the unit by disconnecting the power cord
from the outlet.
This unit operates under SELV (Safety Extra Low Voltage) conditions
according to IEC 60. The conditions are only maintained if the
equipment to which it is connected also operates under SELV conditions.
Only connect an Advanced Redundant Power System (3C16070,
3C16071, 3C16071A or 3C16071B) or Redundant Power System
(3C565047) to the Redundant Power System socket.
■
The cord set must be UL-approved and CSA certified.
■
The minimum specifications for the flexible cord are:
No. 18 AWG
Type SV or SJ
3-conductor
■
The cord set must have a rated current capacity of at least
10A.
■
The attachment plug must be an earth-grounding type
with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A,
250V) configuration.
Denmark
■
The supply plug must comply with Section 107-2-D1,
Standard DK2-1a or DK2-5a.
Switzerland
■
The supply plug must comply with SEV/ASE 1011.
UK
■
The supply plug must comply with BS1363 (3-pin 13-amp)
and be fitted with a 5A fuse which complies with BS1362.
■
The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).
■
The supply plug must comply with CEE7/7 (“SCHUKO”)
■
The mains cord must be <HAR> or <BASEC> marked and
be of type HO3VVF3GO.75 (minimum).
Europe
France and Peru only
This unit cannot be powered from IT † supplies. If your supplies are of IT type, this
L’INFORMATION
DE
SÉCURITÉ IMPORTANTE
Veuillez lire à fond l'information de la sécurité suivante avant
d'installer le Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX
plus 1-Port 1000BASE-T.
France et Pérou uniquement:
Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos
alimentations sont du type impédance à la terre, ce groupe doit être alimenté par
une tension de 230 V (2 P+T) par le biais d’un transformateur d’isolement à rapport
1:1, avec un point secondaire de connexion portant l’appellation Neutre et avec
raccordement direct à la terre (masse).
Cordon électrique
Il doit être agréé dans le pays d’utilisation.
■ Le cordon doit avoir reçu l’homologation des UL et un
Etats-Unis et
Canada:
certificat de la CSA.
■ Le cordon souple doit respecter, à titre minimum, les
spécifications suivantes:
calibre 18 AWG
type SV ou SJ
à 3 conducteurs
■ Le cordon doit être en mesure d’acheminer un courant
nominal d’au moins 10 A.
■ La prise femelle de branchement doit être du type à mise à la
terre (mise à la masse) et respecter la configuration NEMA
5-15P (15 A, 125 V) ou NEMA 6-15P (15 A, 250 V).
AVERTISSEMENT: L’installation et la dépose de ce groupe doivent
être confiés à un personnel qualifié.
„
„
„
„
„
„
„
Si vous entassez l’unité Switch avec les unités SuperStack 3 Hub, l’unité
Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus 1-Port
1000BASE-T doit être installée en dessous des unités Hub plus étroites.
Ne branchez pas votre appareil sur une prise secteur (alimentation
électrique) lorsqu'il n'y a pas de connexion de mise à la terre (mise à la
masse).
Vous devez raccorder ce groupe à une sortie mise à la terre (mise à la
masse) afin de respecter les normes internationales de sécurité.
Le coupleur d’appareil (le connecteur du groupe et non pas la prise
murale) doit respecter une configuration qui permet un branchement
sur une entrée d’appareil EN60320/IEC 320.
La prise secteur doit se trouver à proximité de l’appareil et son accès
doit être facile. Vous ne pouvez mettre l’appareil hors circuit qu’en
débranchant son cordon électrique au niveau de cette prise.
L’appareil fonctionne à une tension extrêmement basse de sécurité qui
est conforme à la norme IEC60950. Ces conditions ne sont maintenues
que si l’équipement auquel il est raccordé fonctionne dans les mêmes
conditions.
Branchez uniquement un Advanced Redundant Power System
(3C16070, 3C16071, 3C16071A ou 3C16071B) ou un Redundant Power
System (3C565047) sur la prise femelle du Redundant Power System.
Danemark:
■
La prise mâle d’alimentation doit respecter la section 107-2 D1
de la norme DK2 1a ou DK2 5a.
Suisse:
■
La prise mâle d’alimentation doit respecter la norme SEV/ASE
1011.
Europe
■
La prise secteur doit être conforme aux normes CEE 7/7
(“SCHUKO”)
LE cordon secteur doit porter la mention <HAR> ou <BASEC>
et doit être de type HO3VVF3GO.75 (minimum).
■
WICHTIGE SICHERHEITSINFORMATIONEN
„
Bitte unbedingt vor dem Einbauen des Baseline 10/100 Switch 24
Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T Einheit die
folgenden Sicherheitsanweisungen durchlesen.
„
WARNUNG: Die Installation und der Ausbau des Geräts darf nur
durch Fachpersonal erfolgen.
„
„
„
„
Wenn die Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T Einheit in einer Stapel mit anderen SuperStack 3
Hub Einheiten eingebaut werden soll, muß die Baseline 10/100 Switch
24 Port 10BASE-T/100BASE-TX plus 1-Port 1000BASE-T Einheit unter die
schmaleren Hub Einheiten eingebaut werden.
Das Gerät nicht an eine Wechselstromsteckdose anschließen, die nicht
geerdet ist.
Das Gerät muß an eine geerdete Steckdose angeschlossen werden, die
die internationalen Sicherheitsnormen erfüllt.
Der Gerätestecker (der Anschluß an das Gerät, nicht der
Wandsteckdosenstecker) muß eine passende Konfiguration für einen
Geräteeingang gemäß EN60320/IEC320 haben.
„
Die Netzsteckdose muß in der Nähe des Geräts und leicht zugänglich
sein. Die Stromversorgung des Geräts kann nur durch Herausziehen des
Gerätenetzkabels aus der Netzsteckdose unterbrochen werden.
Der Betrieb dieses Geräts erfolgt unter den SELV-Bedingungen
(Sicherheitskleinstspannung) gemäß IEC 60. Diese Bedingungen sind nur
gegeben, wenn auch die an das Gerät angeschlossenen Geräte unter
SELV-Bedingungen betrieben werden.
Nur ein Advanced Redundant Power System (3C16070, 3C16071,3C16071A
oder 3C16071B) oder Redundant Power System (3C565047) an den
Redundant Power System Anschluß anschließen.
Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden:
Schweiz
■ Dieser Stromstecker muß die SEV/ASE 1011Bestimmungen
einhalten.
Europe
■
■
5
Das Netzkabel muß vom Typ HO3VVF3GO.75
(Mindestanforderung) sein und die Aufschrift <HAR> oder
<BASEC> tragen.
Der Netzstecker muß die Norm CEE 7/7 erfüllen (”SCHUKO”).
TECHNICAL INFORMATION
Related Standards
Physical
Width
Depth
Height
Weight
Mounting
The SuperStack 3 Baseline 10/100 Switch 24 Port
10BASE-T/100BASE-TX plus 1-Port 1000BASE-T has been
designed to the following standards:
Functional
ISO 8802-3, IEEE 802.3 (Ethernet), IEEE 802.3u
(Fast Ethernet), IEEE 802.3ab (Gigabit Ethernet) IEEE 802.3x (Flow Control) IEEE 802.1D
1998 (Bridging)
Safety
UL 1950, EN 60950, CSA 22.2 #950, IEC
60950
EMC Emissions EN 55022 Class A, FCC Part 15 Subpart B
Class A, ICES-003 Class A, VCCI Class A,
AS/NZS 3548 Class A, CNS 13438 Class A
Immunity
EN 55024
440mm (17.3in.)
235mm (9.3in.)
44mm (1.7in.) or 1U
2.6kg (5.8lb)
Free standing, or 19in. rack mounted using
the mounting kit supplied
Electrical
Power Inlet
AC Line Frequency
Input Voltage
Current Rating
Maximum Power
Consumption
Maximum Power
Dissipation
Environmental
Operating Temperature 0–50°C (32–122°F)
Humidity
10–95% (non-condensing)
Standard
EN 60068 (IEC 68)—various parts
IEC 320
50/60 Hz
100–240 VAC
1 Amps (maximum)
42 VA
142 BTU/hr
LIMITED WARRANTY
meeting this standard. If it appears that any product that is stated to meet this
standard does not perform properly with regard to such date data on and after
January 1, 2000, and Customer notifies 3Com within ninety (90) days after purchase
of the product from 3Com or its authorized reseller, 3Com shall, at its option and
expense, provide a software update which would effect the proper performance of
such product, repair such product, deliver to Customer an equivalent product to
replace such product, or if none of the foregoing is feasible, refund to Customer the
purchase price paid for such product.
Any software update or replaced or repaired product will carry a Year 2000 Warranty
for ninety (90) days after purchase.
OBTAINING WARRANTY SERVICE: Customer must contact a 3Com Corporate
Service Center or an Authorized 3Com Service Center within the applicable warranty
period to obtain warranty service authorization. Dated proof of purchase from 3Com
or its authorized reseller may be required. Products returned to 3Com's Corporate
Service Center must be pre-authorized by 3Com with a User Service Order (USO)
number (or a Return Material Authorization (RMA) number or a Service Repair Order
(SRO) number, whichever was issued) marked on the outside of the package, and
sent prepaid and packaged appropriately for safe shipment, and it is recommended
that they be insured or sent by a method that provides for tracking of the package.
Responsibility for loss or damage does not transfer to 3Com until the returned item
is received by 3Com. The repaired or replaced item will be shipped to Customer, at
3Com's expense, not later than thirty (30) days after 3Com receives the defective
product, and 3Com will retain risk of loss or damage until the item is delivered to
Customer.
3Com shall not be responsible for any software, firmware, information, or memory
data of Customer contained in, stored on, or integrated with any products returned
to 3Com for repair, whether under warranty or not.
Dead- or Defective-on-Arrival. In the event a product completely fails to function
or exhibits a defect in materials or workmanship within the first forty-eight (48)
hours of installation but no later than thirty (30) days after the date of purchase, and
this is verified by 3Com, it will be considered dead- or defective-on-arrival (DOA) and
a replacement shall be provided prior to 3Com receiving the defective product, but
only if Customer provides a purchase order number, credit card number, or other
method of payment acceptable to 3Com, to be used if 3Com needs to charge
Customer for the replacement, as explained below. The replacement product will
normally be shipped not later than three (3) business days after 3Com's verification
of the DOA product, but may be delayed due to export or import procedures. The
shipment of a replacement product prior to 3Com receiving the defective product is
subject to local legal requirements and may not be available in all locations. When
such a replacement is provided and Customer fails to return the original product to
3Com within fifteen (15) days after shipment of the replacement, 3Com will charge
Customer for the replacement product, at list price.
Shipment of a Replacement Prior to 3Com Receiving the Defective Product is
provided for five (5) years, after which time it may be available for a specified fee,
but in either case only if Customer provides a purchase order number, credit card
number, or other method of payment acceptable to 3Com, to be used if 3Com
needs to charge Customer for the replacement, as explained below. 3Com will make
commercially reasonable efforts to ship the replacement product not later than five
(5) business days after receiving the request for a replacement, but may be delayed
due to product availability or export or import procedures. The shipment of a
replacement product prior to 3Com receiving the defective product is subject to local
legal requirements and may not be available in all locations. When such a
replacement is provided and Customer fails to return the original product to 3Com
within fifteen (15) days after shipment of the replacement, 3Com will charge
Customer for the replacement, at list price. This replacement prior to 3Com receiving
This warranty applies to customers located in the United States, Australia, Canada
(except Quebec), Ireland, New Zealand, U.K., and other English language countries,
and countries for which a translation into the local language is not provided.
SuperStack 3 Baseline 10/100 Switch 24-Port 10BASE-T/100BASE-TX plus
1-Port 1000BASE-T (3C16467)
HARDWARE: 3Com warrants to the end user ("Customer") that this hardware
product will be free from defects in workmanship and materials, under normal use
and service, for the following length of time from the date of purchase from 3Com
or its authorized reseller:
Lifetime, for as long as the original Customer owns the product (not transferable to
a subsequent end user)
3Com's sole obligation under this express warranty shall be, at 3Com's option and
expense, to repair the defective product or part, deliver to Customer an equivalent
product or part to replace the defective item, or if neither of the two foregoing
options is reasonably available, 3Com may, in its sole discretion, refund to Customer
the purchase price paid for the defective product. All products that are replaced will
become the property of 3Com. Replacement products or parts may be new or
reconditioned. 3Com warrants any replaced or repaired product or part for ninety
(90) days from shipment, or the remainder of the initial warranty period, whichever
is longer.
SOFTWARE: 3Com warrants to Customer that each software program licensed from
it, except as noted below, will perform in substantial conformance to its program
specifications, for a period of ninety (90) days from the date of purchase from 3Com
or its authorized reseller. 3Com warrants the media containing software against
failure during the warranty period. No updates are provided, unless specifically
included in the Included Services section. 3Com's sole obligation under this express
warranty shall be, at 3Com's option and expense, to refund the purchase price paid
by Customer for any defective software product, or to replace any defective media
with software which substantially conforms to applicable 3Com published
specifications. Customer assumes responsibility for the selection of the appropriate
applications program and associated reference materials. 3Com makes no warranty
or representation that its software products will meet Customer's requirements or
work in combination with any hardware or applications software products provided
by third parties, that the operation of the software products will be uninterrupted or
error free, or that all defects in the software products will be corrected. For any third
party products listed in the 3Com software product documentation or specifications
as being compatible, 3Com will make reasonable efforts to provide compatibility,
except where the non-compatibility is caused by a "bug" or defect in the third
party's product or from use of the software product not in accordance with 3Com's
published specifications or user manual.
THIS 3COM PRODUCT MAY INCLUDE OR BE BUNDLED WITH (1) THIRD PARTY
SOFTWARE, OR (2) 3COM SOFTWARE THAT IS LICENSED "AS IS", THE USE OF
WHICH IS GOVERNED BY A SEPARATE END USER LICENSE AGREEMENT. THIS 3COM
WARRANTY DOES NOT APPLY TO SUCH THIRD PARTY SOFTWARE OR 3COM
SOFTWARE LICENSED "AS IS". FOR THE APPLICABLE WARRANTY, PLEASE REFER TO
THE END USER LICENSE AGREEMENT GOVERNING THE USE OF SUCH SOFTWARE OR
THE ACCOMPANYING DOCUMENTATION RELATING TO SUCH SOFTWARE.
YEAR 2000 WARRANTY: In addition to the Hardware Warranty and Software
Warranty stated above, 3Com warrants that each product sold or licensed to
Customer on and after January 1, 1998 that is date sensitive will continue
performing properly with regard to such date data on and after January 1, 2000,
provided that all other products used by Customer in connection or combination
with the 3Com product, including hardware, software, and firmware, accurately
exchange date data with the 3Com product, with the exception of those products
identified at 3Com's Web site, http://www.3com.com/products/yr2000.html, as not
6
UNAUTHORIZED ATTEMPTS TO OPEN, REPAIR OR MODIFY THE PRODUCT, OR ANY
OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT,
FIRE, LIGHTNING, POWER CUTS OR OUTAGES, OTHER HAZARDS, OR ACTS OF
GOD.
LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW, 3COM ALSO
EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN
CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR
FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION
OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH
THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR
INTERRUPTION OF ITS PRODUCTS, EVEN IF 3COM OR ITS AUTHORIZED RESELLER
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS
LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID,
AT 3COM'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL
PURPOSE.
DISCLAIMER: Some countries, states, or provinces do not allow the exclusion or
limitation of implied warranties or the limitation of incidental or consequential
damages for certain products supplied to consumers, or the limitation of liability for
personal injury, so the above limitations and exclusions may be limited in their
application to you. When the implied warranties are not allowed to be excluded in
their entirety, they will be limited to the duration of the applicable written warranty.
This warranty gives you specific legal rights which may vary depending on local law.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of the
State of California, U.S.A., and by the laws of the United States, excluding their
conflicts of laws principles. The United Nations Convention on Contracts for the
International Sale of Goods is hereby excluded in its entirety from application to this
Limited Warranty.
3Com Corporation
5400 Bayfront Plaza
P.O. Box 58145
Santa Clara, CA 95052-8145
(408) 326-5000
August 2000
3Com reserves the right to modify or cancel this offering at any time, without
advance notice. This offering is not available where prohibited or restricted by law.
the defective product is different from the fee-based Advance Hardware
Replacement Service, which is available as a contracted service offering.
INCLUDED SERVICES:
3Com's Electronic Support Services, available at no charge, include 3Com
Knowledgebase, information on known bugs, documentation, release notes, and
publicly available software and firmware upgrades. 3Com reserves the right to
modify or cancel this offering at any time, without advance notice.
Telephone Technical Support, with coverage for basic troubleshooting only, will
be provided at no additional charge for 12 months from the date of purchase, on a
commercially reasonable efforts basis. Telephone support is provided by 3Com only
if Customer purchased this product directly from 3Com, or if Customer's reseller is
unable to provide telephone support. To qualify for this telephone technical
support, Customer must register on the 3Com Web site at
http://support.3Com.com/index.htm, and state the date of purchase, product
number, and serial number. 3Com's response to a request for telephone technical
support will be in the form of a return call from a 3Com representative by close of
business the following business day, defined as 9 a.m. to 5 p.m., local time,
Monday through Friday, excluding local holidays. Please refer to the Technical
Support appendix in the User Guide for telephone numbers.
Software Updates, All software and firmware upgrades and the latest code for
this product downloaded through the 3Com Software Library.
WARRANTIES EXCLUSIVE: IF A 3COM PRODUCT DOES NOT OPERATE AS
WARRANTED ABOVE, CUSTOMER'S SOLE REMEDY FOR BREACH OF THAT
WARRANTY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE
PRICE PAID, AT 3COM'S OPTION. TO THE FULL EXTENT ALLOWED BY LAW, THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF
ALL OTHER WARRANTIES, TERMS, OR CONDITIONS, EXPRESS OR IMPLIED, EITHER
IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
WARRANTIES, TERMS, OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH
DESCRIPTION, AND NON-INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY
DISCLAIMED. 3COM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.
3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND
EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT OR MALFUNCTION IN THE
PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD
PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING,
REGULATORY NOTICES
FCC Statement
In order to meet FCC emissions limits, this equipment must be used only with
cables which comply with IEEE 802.3.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference to radio
communications, in which case the user will be required to correct the interference
at their own expense.
CE Statement (Europe)
This product complies with the European Low Voltage Directive 73/23/EEC and ETIC
Directive 89/336/EEC as amended by European Directive 93/68/EEC/.
CSA Statement
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
Information To The User
VCCI Statement
If this equipment does cause interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
■ Reorient the receiving antenna.
■
Relocate the equipment with respect to the receiver.
■
Move the equipment away from the receiver.
■
Plug the equipment into a different outlet so that equipment and receiver are on
different branch circuits.
BSMI Statement
If necessary, the user should consult the dealer or an experienced radio/television
technician for additional suggestions. The user may find the following booklet
prepared by the Federal Communications Commission helpful:
How to Identify and Resolve Radio-TV Interference Problems
This booklet is available from the U.S. Government Printing Office, Washington,
DC 20402, Stock No. 004-000-00345-4.
PRODUCTS
The SuperStack 3 Baseline 10/100 Switch 24 Port 10BASE-T/100BASE-TX plus 1-Port
1000BASE-T is part of the extensive SuperStack 3 range of 3Com products. This
range includes hubs, switches, power systems and other networking equipment,
and is continually being developed. Contact your supplier for the latest product
information and to order these products.
pddtechpubs_comments@3Com.com
Product Registration
It is the policy of 3Com Corporation to be environmentally-friendly in all operations.
To uphold our policy, we are committed to:
■ Establishing environmental performance standards that comply with national
legislation and regulations.
■ Conserving energy, materials and natural resources in all operations.
■ Reducing the waste generated by all operations.
■ Ensuring that all waste conforms to recognized environmental standards.
■ Maximizing the recyclable and reusable content of all products.
■ Ensuring that all products can be recycled, reused and disposed of safely.
■ Ensuring that all products are labelled according to recognized environmental
standards.
■ Improving our environmental record on a continual basis.
Please include the following information when commenting: the document title,
part number (shown at the bottom of page 8), and page number, if appropriate.
Environmental Statement
You can now register your SuperStack 3 Switch on the 3Com web site to receive
up-to-date information on your product:
http://www.support.3com.com/warrantyregistration/register.pl
Year 2000 Compliance
For information on Year 2000 compliance and 3Com products, visit the 3Com Year
2000 Web page:
http://www.3com.com/products/yr2000.html
Feedback
Your suggestions are very important to us. They will help make our documentation
more useful to you. Please e-mail comments about this document to 3Com at:
7
.
TECHNICAL SUPPORT
The following numbers may be used for technical support:
The following numbers may be used for technical support:
Country
Telephone Number
Country
Telephone Number
Asia, Pacific Rim
Australia
Hong Kong
India
Indonesia
Japan
Malaysia
New Zealand
Pakistan
Philippines
1 800 678 515
800 933 486
+61 2 9937 5085
001 800 61 009
0031 61 6439
1800 801 777
0800 446 398
+61 2 9937 5085
1235 61 266 2602
P.R. of China
10800 61 00137 or
021 6350 1590
800 6161 463
Europe
From anywhere in Europe, call:
Singapore
S. Korea
From anywhere in S. Korea:
From Seoul:
Taiwan, R.O.C.
Thailand
00798 611 2230
(0)2 3455 6455
0080 611 261
001 800 611 2000
+31 (0)30 6029900 phone
+31 (0)30 6054396 fax
Europe, South Africa, and Middle East: From the following countries, you may use the toll-free numbers:
Austria
Belgium
Denmark
Finland
France
Germany
Hungary
Ireland
Israel
Italy
0800 297468
0800 71429
800 17309
0800 113153
0800 917959
0800 1821502
00800 12813
1800 553117
1800 9453794
1678 79489
Netherlands
Norway
Poland
Portugal
South Africa
Spain
Sweden
Switzerland
U.K.
0800 0227788
800 11376
00800 3111206
0800 831416
0800 995014
900 983125
020 795482
0800 55 3072
0800 966197
Latin America
Argentina
Brazil
Chile
Colombia
AT&T +800 666 5065
0800 13 3266
1230 020 0645
98012 2127
Mexico
Peru
Puerto Rico
Venezuela
01 800 CARE (01 800 2273)
AT&T +800 666 5065
800 666 5065
AT&T +800 666 5065
North America
1 800 876-3266
LEGAL NOTICES
For civilian agencies:
Restricted Rights Legend: Use, reproduction or disclosure is subject to restrictions set
forth in subparagraph (a) through (d) of the Commercial Computer Software Restricted Rights Clause at 48 C.F.R. 52.227-19 and the limitations set forth in
3Com Corporation’s standard commercial agreement for the software. Unpublished
rights reserved under the copyright laws of the United States.
If there is any software on removable media described in this documentation, it is
furnished under a license agreement included with the product as a separate
document, in the hard copy documentation, or on the removable media in a
directory file named LICENSE.TXT. If you are unable to locate a copy, please contact
3Com and a copy will be provided to you.
Unless otherwise indicated, 3Com registered trademarks are registered in the United
States and may or may not be registered in other countries.
3Com and SuperStack are registered trademarks of 3Com Corporation.
Other brand and product names may be registered trademarks or trademarks of
their respective holders.
© 3Com Technologies, 2000. All rights reserved. No part of this documentation
may be reproduced in any form or by any means or used to make any derivative
work (such as translation, transformation, or adaptation) without permission from
3Com Technologies.
3Com Technologies reserves the right to revise this documentation and to make
changes in content from time to time without obligation on the part of 3Com
Technologies to provide notification of such revision or change.
3Com Technologies provides this documentation without warranty of any kind,
either implied or expressed, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. 3Com may make improvements
or changes in the product(s) and/or the program(s) described in this documentation
at any time.
UNITED STATES GOVERNMENT LEGENDS:
If you are a United States government agency, then this documentation and the
software described herein are provided to you subject to the following restricted
rights:
For units of the Department of Defense:
Restricted Rights Legend: Use, duplication or disclosure by the Government is
subject to restrictions as set forth in subparagraph (c) (1) (ii) for restricted Rights in
Technical Data and Computer Software clause at 48 C.F.R. 52.227-7013. 3Com
Centre, Boundary Way, Maylands Park South, Hemel Hempstead, Herts, HP2 7YU,
U.K.
Part Number: DUA1646-7AAA02
Published: August 2000
8
Download PDF

advertising