Instruction manual | 3M 4407 Projector User Manual

MP8749
Multimedia Projector
Operator's Guide
01CPX385SW/EN最終 02.11.20 9:29 AM ページ 1
MP8749 Multimedia Projector
Operator's Guide
Thank you for purchasing this projector.
WARNING Please read the "Product Safety Guide" and this "Operator's Guide"
thoroughly to ensure correct usage through understanding.
After reading, store this instruction manual in a safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
Page
Page
PROJECTOR FEATURES ................2
PREPARATIONS ..............................2
PART NAMES ...................................4
SETTING UP THE PROJECTOR .....6
CONNECTING YOUR DEVICES ......8
USING THE REMOTE CONTROL ..13
TURNING ON THE POWER ...........14
TURNING OFF THE POWER .........16
ADJUSTING THE VOLUME ...........17
TEMPORARILY MUTING
THE SOUND....................................17
ADJUSTING THE POSITION..........18
USING THE AUTOMATIC
ADJUSTMENT FEATURE ..............19
CORRECTING
KEYSTONE DISTORTIONS ...........20
USING THE MAGNIFY FEATURE ..21
FREEZING THE SCREEN ..............21
SIGNAL SEARCHING.....................22
SELECTING THE ASPECT RATIO..22
TEMPORARILY
BLANKING THE SCREEN..............22
USING THE MENU FUNCTIONS ...23
MULTIFUNCTIONAL SETTINGS ...24
OPERATING THE PC SCREEN .....29
THE LAMP ......................................30
THE AIR FILTER.............................32
THE HANDLE .................................34
OTHER CARE ................................34
WHAT TO DO WHEN
YOU THINK A MACHINE
DEFECT HAS OCCURRED ...........35
SPECIFICATIONS...........................38
ACCESSORIES...............................39
1
01CPX385SW/EN最終 02.11.20 9:29 AM ページ 2
This liquid crystal projector is used to project
various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space
is required for installation and large images can
easily be realized.
PROJECTOR
FEATURES
●Ultra High Brightness
●Keystone Distortion Correction
●Partial Magnification Function
●Whisper Mode Equipped
Crisp, ultra-bright presentations is achieved
by using a UHB (ultra high brightness) lamp
and a highly efficient optical system
Interesting parts of images can be magnified
for closer viewing
PREPARATIONS
Quick correction of distorted images electrically
Special mode is available for reducing
projector noise to achieve quieter operation
Your projector should come with the items
shown below. Check to make sure that all the
items are included. Contact your dealer if
anything is missing.
NOTE • Keep the original packing material for future reshipment.
Power Cord
(US,UK,Europe)
Stereo Mini Cable
RGB Cable
Video/Audio Cable
(with white lead)
Component
Video Cable
(with green lead)
Mouse cable
(PS/2)
Projector
MP8749
Multimedia Projector
Operator's Guide
MP8749 Projecteur multimedia - Guide de L' opérateur
MP8749 Multimedia-Projektor - Benutzerhandbuch
MP8749 Proyector de Multimedia - Guía del usuario
MP8749 Proiettore Multimediale - Guida dell' operatore
MP8749 Multimedia Projector - Gebruiksaanwijzing
MP8749 Projector dos Multimedia - Guia da operador
MP8749 Multimedia Projektør- Brukerhåndbok
Operator's Guide
Product Safety Guide
Warranty
Quick Start Guide
BLANK
STANDBY/ON
LASER
VIDEO
RGB
AUTO
MENU
Handle
Two AA batteries
(for the remote
control)
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
VOLUME
SEARCH
Remote Control
Carrying Bag
2
01CPX385SW/EN最終 02.11.20 9:29 AM ページ 3
WARNING Precautions to observe in regards to the power cord:
Please use extra caution when connecting the projector's power cord as incorrect
or faulty connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere
to the following safety guidelines to insure safe operation of the projector:
• Only plug the power cord into outlets rated for use with the power cord's specified voltage range.
• Only use the power cord that came with the projector.
• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREEPRONGED PLUG!
• Make sure that you firmly connect the power cord to the projector and wall outlet.
1
Connect your devices to the projector
2
Insert the batteries into the remote
control
3
Connect the power cord
8
∼ 12
Connect your computer, VCR and/or other
devices you will be using to the projector.
13
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
(2) Firmly plug the power cord's plug into the outlet
Power outlet
(2)
Power cord
(1)
AC inlet
3
01CPX385SW/EN最終 02.11.20 9:29 AM ページ 4
THE PROJECTOR
PART NAMES
Indicates the corresponding
reference page
Speaker
15
15
Handle Hook
34
Power Switch
AC Inlet
(to the Power Cord)
Zoom Ring
Focus Ring
13
Remote Control
Sensor
14
Slide lens door
14
3
Ventilation Openings
(Intake)
6
Foot Adjuster
STANDBY/ON Button 14
KEYSTONE Button 20
15
36
36
Foot Adjuster Button
(
14
6
18
23
Filter Cover 3 2
Air Filter and Intake
for the Cooling Fan
INPUT Button
LAMP Indicator
TEMP Indicator
POWER Indicator
RESET Button
MENU Button
)
Rear Foot Adjuster
Ventilation Openings
(exhaust)
6
S-VIDEO Port 11
COMPONENT VIDEO
Y Port
CB/PB Port
CR/PR Port
VIDEO IN Port
4
13
11
10
11
11
1
11
AUDIO IN
AUDIO 1
IN
VIDEO IN
2 AUDIO OUT
RGB IN
Remote Control
Sensor
RGB IN 1 Port
10
RGB IN 2 Port
2
S-VIDEO IN
USB
AUDIO IN R Port
11
AUDIO IN L Port
11
10
CONTROL Port
AUDIO IN 1 Port
10
12
RGB OUT Port
AUDIO IN 2 Port
10
10
USB Port
AUDIO OUT Port
9
RGB OUT
CONTROL
TERMINAL PANEL
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 5
THE REMOTE CONTROL
5 LASER button
BLANK
STANDBY/ON
STANDBY/ON 14
button
22 BLANK button
LASER
VIDEO
RGB
VIDEO button 15
15 RGB button
Disk Pad 29
24 MOUSE / RIGHT
Button
AUTO button 19
AUTO
20 KEYSTONE button
MENU
KEYSTONE
MENU button 23
23 ENTER button
ENTER
,
,
,
23
Cursor buttons
POSITION button 18
ASPECT button 22
MAGNIFY button 21
18 RESET button
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
21 FREEZE button
23 ESC button
17 MUTE button
VOLUME
17 VOLUME button
SEARCH
22 SEARCH button
WARNING The laser pointer of the remote control is used in place of a finger
or rod. Never look directly into the laser beam outlet or point the laser beam at
other people. The laser beam can cause vision problems.
AVOID EXPOSURELASER RADIATIONS IS
EMITTED FROM THIS
APERTURE
C A U T I O N
LASER RADIATIONDO NOT STARE INTO BEAM
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
CLASS2 LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS2 LASER PRODUCT
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
IEC60825-1 : 1993+A1:1997
Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations
pursuant to Laser Notice No.50, dated 2001.7.26
SMK CORPORATION
6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511
MANUFACTURED Novemver 2001
PLACE OF MANUFACTURER: A
NOTE • Keep the remote control away from children and pets.
• Do not give the remote control any physical impact. Take care not to drop.
• Do not place the heavy objects on the remote control.
• Do not wet the remote control or place it on any wet object.
• Do not place the remote control close to the cooling fan of the projector.
• Do not disassemble the remote control.
5
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 6
SETTING UP THE PROJECTOR
CAUTION • Install the projector in a suitable environment according to instructions
of the “Product Safety Guide” and this "Operator's Guide".
• If you press the elevator buttons without holding the projector, the projector might
crash down, overturn, smash your fingers and possibly result in malfunction.
To prevent damaging the projector and injuring yourself, ALWAYS HOLD THE
PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
Angle Adjustment
Use the foot adjusters on the bottom of the projector to adjust the projection
angle. It is variable within 0˚ to 9˚ approximately.
1
Lift up the front side of the
projector, and pressing the foot
adjuster button, adjust the
projection angle.
Press the foot adjuster button
2
3
Release the button to lock at the desired angle.
Turn the rear foot adjuster to adjust
the left-right slope. Do not force the
foot adjuster screws. This could
damage the adjusters or cause the
lock to fail.
Rear Foot Adjuster
6
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 7
Adjusting the Screen Size and Projection Distance
Refer to the illustrations and tables below to determine the screen size and
projection distance.
The values shown in the table are calculated for a full size screen
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
If 4:3 aspect ratio
4
3
Top View
Screen size
[inches (m)]
40 (1.0)
60 (1.5)
a
Side View
a [inches (m)]
Min.
Max.
47 (1.2)
71 (1.8)
59 (1.5)
87 (2.2)
80 (2.0)
94 (2.4)
114 (2.9)
100 (2.5)
118 (3.0)
142 (3.6)
120 (3.0)
142 (3.6)
173 (4.4)
150 (3.8)
177 (4.5)
217 (5.5)
200 (5.0)
240 (6.1)
287 (7.3)
7
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 8
CONNECTING YOUR DEVICES
Devices You Can Connect to the Projector
(Refer to this section for planning your device
configuration to use for your presentation.)
CAUTION Incorrect connecting could result in fire or electrical shock. Please
read the "Product Safety Guide" and this “Operator's Guide”.
ATTENTION Precautions to observe when connecting other devices to the projector :
• Whenever attempting to connect other devices to the projector, please thoroughly
read the manual of each device to be connected.
• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to
connect a live device to the projector may generate extremely loud noises or other
abnormalities that may result in malfunction and/or damage to the device and/or
projector. Refer to the “TECHNICAL” for the pin assignment of connectors and
RS-232C communication data.
• Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
• Some cables may have to be used with core set. Use the accessory cable or a
designated-type cable for the connection. For cables that have a core only at one
end, connect the core to the projector.
• Secure the screws on the connectors and tighten.
Indicates the
corresponding
reference page
12 Display monitors
11 DVD players
10 Laptop computers
11 VCRs
10 Desktop computers
8
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 9
Ports and Cables
Refer to the table below to find out which projector port and cable to use for connecting a
given device. Use this table for determining which cables to prepare.
Function
Projector Port
RGB IN 1
RGB input
RGB IN 2
RGB output
Audio input
(from the computer)
USB mouse control
RGB OUT
Connection Cables
RGB cable
with D-sub 15-pin shrink jack and
inch thread screws
AUDIO IN 1
(interlocked with RGB IN 1)
Audio cable with stereo mini jack
AUDIO IN 2
(interlocked with RGB IN 2)
USB
PS/2 mouse control
USB cable
PS/2 mouse cable
ADB mouse control
ADB mouse cable
CONTROL
Serial mouse control
Serial mouse cable
RS-232C communication
RS-232C cable
S-video input
S-VIDEO IN
S-video cable with mini DIN 4-pin jack
Video input
VIDEO IN
Audio/video cable
COMPONENT VIDEO Y
Component video input
COMPONENT VIDEO CB/PB
Component video cable
COMPONENT VIDEO CR/PR
Audio input
(from video equipment)
AUDIO IN L
AUDIO IN R
Audio/video cable or
Audio cable with RCA jack
Audio output
AUDIO OUT
Audio cable with stereo mini jack
NOTE About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by
connecting this projector to computers that are VESA DDC (display data channel)
compatible. Please take advantage of this function by connecting the accessory RGB
cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices).
• Please use the standard drivers as this projector is a Plug-and-Play monitor.
• Plug-and-Play may not function properly with some type of computers. Use the RGB
IN 2 port if Plug-and-Play does not function correctly.
9
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 10
CONNECTING YOUR DEVICES (continued)
Connecting to a Computer
ATTENTION Whenever attempting to connect a laptop computer to the projector,
be sure to activate the laptop's RGB external image output (set the laptop to CRT
display or to simultaneous LCD and CRT display). For details on how this is done,
please refer to the instruction manual of the corresponding laptop computer.
1
AUDIO IN
AUDIO 1
IN
VIDEO IN
2 AUDIO OUT
S-VIDEO IN
1
2
RGB IN
AUDIO IN
AUDIO 1
IN
RGB OUT
2 AUDIO OUT
C
B
RGB OUT
CONTROL
A
B
10
CONTROL OUT
Analogue
RGB OUT
NOTE
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• For some RGB input modes, the optional Mac adapter is necessary.
MOUSE cable
RGB cable
AUDIO OUT
Analogue
RGB OUT
USB OUT
AUDIO cable
RGB cable
AUDIO cable
AUDIO OUT
Desktop computer
CONTROL IN
RGB IN
C
AUDIO IN
USB IN
RGB IN
AUDIO IN
Laptop computer
USB cable
If connecting to a
USB port equipped
computer
D
2
A
USB
D
CONTROL
A
B
RGB IN
S-VIDEO IN
A
USB
B
VIDEO IN
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 11
Connecting to a DVD Player
A A A
AUDIO IN
VIDEO IN
1
AUDIO 1
IN
2
RGB IN
S-VIDEO IN
B B B
C
2 AUDIO OUT
USB
RGB OUT
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
COMPONENT VIDEO OUT
COMPONENT cable
S-VIDEO IN
C
AUDIO/VIDEO IN
B
COMPONENT VIDEO IN
A
CONTROL
If using an audio/video
connection
If using a component
video connection
DVD player
Connecting to a VCR
1
AUDIO IN
VIDEO IN
A A A
AUDIO 1
IN
2 AUDIO OUT
RGB IN
2
S-VIDEO IN
B
USB
RGB OUT
S-VIDEO IN
B
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
AUDIO/VIDEO IN
A
CONTROL
VCR
11
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 12
CONNECTING YOUR DEVICES (continued)
Connecting to a Display Monitor
1
AUDIO IN
AUDIO 1
IN
VIDEO IN
2 AUDIO OUT
2
RGB IN
S-VIDEO IN
A
USB
RGB OUT
CONTROL
A
RGB OUT
RGB IN
RGB cable
Display monitor
12
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 13
USING THE REMOTE CONTROL
Putting batteries into the remote control unit
CAUTION Precautions to observe in regards to the batteries:
Always handle the batteries with care and use them only as directed. Improper use may result in battery
cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
1
Remove the battery
cover
Push the knob while lifting
up the battery cover in the
direction of the arrow.
2
Insert the batteries
Align and insert the two AA
batteries (that came with the
projector) according to their plus
and minus terminals (as indicated
in the remote control).
Close the battery
cover
3
Replace the battery cover
in the direction of the arrow
and snap it back into place.
Operating the remote control
30
30
• The remote control works with both the
projector's front and rear remote sensors.
• The range of the remote sensor on the front and
back is 3 meters with a 60-degree range (30
degrees to the left and right of the remote sensor).
• Since the remote control uses infrared light to send
30
30
de
de
gre
gre
es
es
signals to the projector (Class 1 LED), be sure to
use the remote control in an area free from
approximately
approximately
obstacles that could block the remote control's
3 meters
3 meters
output signal to the projector.
• Only use the accompanying remote control. Using other remote controls (even of similiar models) to control the
CP-X385W may result in unexpected operation.
s
ee
s
ee
gr
gr
de
de
ATTENTION Precautions to observe when using the remote control:
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if you
won't be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunction.
• When strong light, such as direct sunlight or light from an extremely close range (such as from an
inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function.
Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.
13
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 14
TURNING ON THE POWER
Precautions
Connect all devices to be used to the projector prior to turning on the power.
8
∼ 12
WARNING When the power is ON, a strong light is emitted. Do not look into the
lens.
BLANK
STANDBY/ON
1
LASER
VIDEO
Make sure that the power cord is firmly and
correctly connected to the projector and outlet
3
RGB
2
Turn on the projector's power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
POWER-indikator
Control panel
på/av-bryter
3
NOTE Turn the
power on/off in
right order.
• Power on the
projector before the
computer or video
tape recorder.
• Power off the
projector after the
computer or video
tape recorder.
14
Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
STANDBY/ON
• The POWER indicator stops blinking and
lights to solid green once the projector's
power is completely on.
4
Open the slide lens door
The picture is projected.
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 15
Selecting an Input Signal
5
Using the remote control
If selecting RGB input
Press the RGB button
Using the projector's control panel
Press the INPUT button
Press this button to toggle between the
devices connected to RGB IN 1 and 2.
As illustrated below, each time you
press the RGB button, the projector
switches between RGB IN 1 and 2.
Select the signal you wish to project.
As illustrated below, each time you
press the INPUT button, the projector
switches between its input signal
ports. Select the signal you wish to
project.
INPUT
RGB
RGB IN 1
RGB IN 2
RGB IN 1
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, SVIDEO IN and COMPONENT VIDEO. As
illustrated below, each time you press
the VIDEO button, the projector
switches between VIDEO IN, S-VIDEO
IN and COMPONENT VIDEO. Select the
signal you wish to project.
VIDEO
VIDEO IN
RGB IN 2
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
S-VIDEO IN
COMPONENT VIDEO
6
Use the zoom ring to adjust the
screen size
7
Use the focus ring to focus the
picture
15
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 16
TURNING OFF THE POWER
1
BLANK
STANDBY/ON
Press the STANDBY/ON button (control
panel or remote control)
The message "Power off?" will appear on the screen for approximately 5 seconds.
LASER
STANDBY/ON
VIDEO
RGB
2
Press the STANDBY/ON button again while the "Power off?"
message is visible. The projector lamp goes off and starts cooling
down. The POWER indicator blinks orange while the lamp cools
down. (Pressing the STANDBY/ON button while the POWER
indicator is blinking orange has no effect.)
The system goes into the STANDBY mode after cooling
down and the POWER indicator stops blinking STANDBY/ON
orange and then lights to solid orange.
AUTO
MENU
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
Press the STANDBY/ON button again
(control panel or remote control)
VOLUME
Control panel
3
Check that the POWER indicator stops
blinking and lights to solid orange.
Switch the power switch to [O] (OFF).
POWER-indikator
på/av-bryter
4
NOTE
• Except in
emergencies, follow
the abovementioned
procedure for
turning power off.
16
Confirm that the POWER indicator has gone
off and then close the slide lens door.
When the projector has completed powering down, the
POWER indicator will go off.
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 17
ADJUSTING THE VOLUME
BLANK
STANDBY/ON
1
LASER
VIDEO
RGB
Press the VOLUME button
VOLUME
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
VOLUME
16
2
AUTO
MENU
Press the
the volume
,
buttons to adjust
Press the VOLUME button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
Press this to increase the volume
VOLUME
Press this to decrease the volume
VOLUME
SEARCH
16
TEMPORARILY MUTING THE SOUND
1
AUTO
MENU
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound. Press
the VOLUME button to close the dialog. (Even if you don't
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
VOLUME
MUTE
VOLUME
SEARCH
16
17
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 18
ADJUSTING THE POSITION
BLANK
STANDBY/ON
1
LASER
VIDEO
Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
RGB
POSITION
POSITION
AUTO
MENU
KEYSTONE
2
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
VOLUME
SEARCH
Control panel
18
Use the
,
the position
,
,
buttons to adjust
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB IN 1/2 input.
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 19
USING THE AUTOMATIC ADJUSTMENT FEATURE
1
BLANK
STANDBY/ON
Press the AUTO button
AUTO
LASER
VIDEO
RGB
Automatic Adjustment for RGB Input
AUTO
MENU
KEYSTONE
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly adjusted. Use a
bright screen when adjusting.
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
VOLUME
Automatic Adjustment for Video Input
The signal type best suited for the respective input
signal is selected automatically.
This feature is available only if VIDEO is set to AUTO in
the INPUT menu.
SEARCH
NOTE
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
19
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 20
CORRECTING KEYSTONE DISTORTIONS
BLANK
STANDBY/ON
1
LASER
VIDEO
RGB
Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion.
KEYSTONE
KEYSTONE
KEYSTONE
16
AUTO
MENU
2
Use the
,
buttons to select the
direction of distortion to correct ( /
3
Use the
distortion
KEYSTONE
)
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
VOLUME
SEARCH
,
buttons to correct the
Press the KEYSTONE button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
Control panel
NOTE
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
20
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 21
USING THE MAGNIFY FEATURE
BLANK
STANDBY/ON
LASER
VIDEO
1
Press the MAGNIFY (ON) button
The projector enters MAGNIFY mode.
MAGNIFY
ON
RGB
the POSITION button, then use the
, ,
2 ,Pressbuttons
to select the area to enlarge and then
press the POSITION button again to confirm your
selection POSITION
POSITION
AUTO
MENU
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
3
Press the
,
buttons to zoom in and
out of the selected area.
Press the MAGNIFY (OFF) button to exit MAGNIFY mode
and restore the screen to normal. (The projector will also
automatically exit MAGNIFY mode if there is a change in the
input signal's state.)
VOLUME
SEARCH
NOTE
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
FREEZING THE SCREEN
ENTER
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
1
Press the FREEZE button
The [II] icon appears and the screen will freeze at
the current image. Press the FREEZE button again
and the [ ] appears as the projector exits
FREEZE mode.
FREEZE
▲
POSITION
VOLUME
SEARCH
NOTE
• The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.
• If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.
21
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 22
SIGNAL SEARCHING
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
1
VOLUME
Press the SEARCH button
When you press the SEARCH button, the projector begins
searching for input signals. If it detects an input signal, the
search will cease and the projector will project the detected
signal. If the projector is unable to find an input signal at any of
its ports, it will return to the state it was in prior to the search.
SEARCH
SEARCH
RGB IN 1
RGB IN 2
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
SELECTING THE ASPECT RATIO
1
AUTO
MENU
Press the ASPECT button
ASPECT
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
RGB IN 1, RGB IN 2, COMPONENT VIDEO
(HDTV signals : 1125i (1035i/1080i), 750p)
4:3
16:9
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO
(Non-HDTV signals : 525i, 525p,625i)
VOLUME
SEARCH
4:3
16:9
SMALL
TEMPORARILY BLANKING THE SCREEN
BLANK
STANDBY/ON
LASER
VIDEO
RGB
1
Press the BLANK button
The input signal screen is shut off, and a blank screen
appears. You can set the blank screen using the menu
(from the SCREEN menu, select BLANK). Press the BLANK
button again to remove the blank screen, and return to the
input signal screen.
BLANK
AUTO
22
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 23
USING THE MENU FUNCTIONS
BLANK
STANDBY/ON
1
Press the MENU button
2
/
Select a menu using the
buttons,
then press the
or ENTER button.
LASER
VIDEO
RGB
AUTO
MENU
The display of the selected menu appears.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select PICTURE-1, then press
the
or ENTER button.
MENU
KEYSTONE
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
ENTER
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
–1
+1
–1
+1
–1
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
: SELECT
VOLUME
3
MENU
The menu display appears on the screen. The
projector has the following menus: MAIN,
PICTURE-1, PICTURE-2, INPUT, SCREEN, and
OPTION. Select a menu using the
/
buttons. The
current settings of the items that can be manipulated via the
selected menu appear.
Select an item using the
or ENTER button.
/
buttons, then press the
The operation display of the selected item appears. To adjust a numerical value,
press the
or ENTER button again to switch to the single menu (small display
showing only the operation display area).
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select SHARPNESS, then
MENU
press the
or ENTER button.
MAIN
COLOR BAL R
ENTER
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
COLOR BAL B
SHARPNESS
COLOR
TINT
0
: SELECT
4
Press the
/
buttons to adjust the level.
Press the MENU button to hide the menu and finish your operation. Alternatively,
press the
or ESC button to return to the previous display.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to adjust the SHARPNESS.
23
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 2
MULTIFUNCTIONAL SETTINGS
This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT,
SCREEN, OPTION. Each of these menus is operated using the same methods.
The basic operations of these menus are as follows.
Menu screen display : Press the "MENU" button.
Menu selection
: Choose a menu name using the
/
button, and press the
button or the ENTER button.
Item selection
: Choose an item using the
/
button, and press the
button or the ENTER button.
Return menu to last previous screen: Press the
button or the ESC button.
Execution of settings and/or adjustments: Operate by using the
/
button. (For further
details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are
performed simultaneously with the operation
of clock phase, language selection, automatic
adjustment, etc., cannot be initialized.)
End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
With the MAIN menu, the seven items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the Table.
Item
Adjust Brightness: Light
CONTRAST
Adjust Contrast: Strong
24
⇔
Dark
⇔
Weak
Select Aspect Ratio:
At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO
Input:
4:3
⇔
16:9
At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input:
4:3
⇔
16:9
⇔
SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
Select Picture Position (for 16:9/SMALL Picture):
TOP
⇔
CENTER
⇔
BOTTOM
GAMMA
Select Gamma Mode:
NORMAL
⇔
CINEMA
MIRROR
Select Mirror Status:
NORMAL
⇔
H:INVERT
LANGUAGE
12
: SELECT
Description
BRIGHT
PICT.POSIT.
BRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
Example : MAIN Menu
(BRIGHT)
MAIN Menu
ASPECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
⇔
⇔
DYNAMIC
V:INVERT
⇔
H&V:INVERT
Select Menu Language:
ENGLISH
⇔
FRANÇAIS
⇔
DEUTSCH
⇔
ESPAÑOL
⇔
ITALIANO
⇔
NORSK
⇔
NEDERLANDS
⇔
中文
⇔
日本語
⇔
POTUGUÊS
⇔
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 3
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
PICTURE 1 Menu
With the PICTURE 1 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
12
: SELECT
Example : PICTURE1 Menu
(COLOR BAL R)
PICTURE1 Menu
Item
Description
COLOR BAL R
Adjust Red Color Balance: Dark
⇔
Light
COLOR BAL B
Adjust Blue Color Balance: Dark
⇔
Light
SHARPNESS
COLOR
TINT
⇔
Adjust Sharpness (for VIDEO/S-VIDEO): Clear
Soft
Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO):
Dark
⇔
Light
⇔
Adjust Tint (for VIDEO/S-VIDEO): Green
PICTURE 2 Menu
With the PICTURE 2 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
Red
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
V POSITION
H POSITION
H PHASE
H SIZE
OVER SCAN
12
: SELECT
Example : PICTURE2 Menu
(V POSITION)
PICTURE2 Menu
Item
Description
V POSITION
Adjust Vertical Position (for RGB): Up
H POSITION
Adjust Horizontal Position (for RGB): Left
H PHASE
⇔
Down
⇔
Right
Adjust Horizontal Phase (for RGB/COMPONENT VIDEO):
Right
⇔
Left
• Adjust to eliminate flicker.
H SIZE
Adjust Horizontal Size (for RGB): Large
⇔
Small
• If the horizontal size adjustment is excessive, the image may not be displayed
correctly. In such a case, initialize H SIZE with the RESET button.
OVER SCAN
Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO):
LARGE
⇔
MIDDLE
⇔
SMALL
• It is recommended to select SMALL to avoid flicker at the lower part of the
picture.
25
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 4
MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
With the INPUT menu, the four items shown in the Table below can be
performed. With inputting of RGB IN 1 and RGB IN 2 signals, the
horizontal and vertical frequencies of the signals will be displayed on the
initial screen of the INPUT menu.
Perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
AUTO
VIDEO
HDTV
SYNC ON G
EXECUTE
: SELECT
Example : INPUT Menu
(AUTO)
INPUT Menu
26
Item
Description
AUTO
Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO
mode for the current input signal. This function is active only when the AUTO
mode is selected for the item VIDEO. Refer to the description for the item
VIDEO below.
• This function may not be available with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
VIDEO
Select Mode of Signal Type (for VIDEO/S-VIDEO):
AUTO
⇔
NTSC
⇔
PAL
⇔
SECAM
⇔
NTSC4.43
⇔
M-PAL
⇔
N-PAL
Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. It automatically selects the proper mode from among those above.
Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g.
The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
HDTV
Select HDTV Signal Mode:
1080i
⇔
1035i
• If the selected HDTV mode is incompatible with the input signal, the picture
may be distorted.
SYNC ON G
On/Off SYNC ON G Mode:
TURN ON
⇔
TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode
allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input
signals. In such a case, remove the signal connector so that no signal is
received and turn SYNC ON G off, and then reconnect the signal.
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 5
SCREEN Menu
With the SCREEN menu, the five items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BLANK
START UP
MyScreen
MyScreen Size
MyScreen Lock
MyScreen
ORIGNAL
: SELECT
Example : SCREEN Menu
(BLANK)
SCREEN Menu
Item
Description
BLANK
Selection of BLANK Screen:
MyScreen
⇔
ORIGINAL
⇔
. .
⇔
.
.
⇔
. .
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the
“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).
MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
Option screens: Various colored non-patterned (plain) screens displayed within the Menus.
• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color
screen several minutes after being displayed.
START UP
Selection of START UP Screen:
MyScreen
⇔
ORIGINAL
⇔
TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when
no signal has been inputted, or when spec signals are being inputted.
MyScreen: Using the MyScreen category (see this Table, below), one can register a
desired screen (or screens). At the time of factory shipment, this is set as a non-patterned
(plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
TURN OFF: A non-patterned (plain) blue color screen.
• The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several
minutes after being displayed.
MyScreen
Registration of MyScreen:
When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen
and the START UP Screen is displayed. When operations are performed in accordance with this Menu,
one can “cut” and register desired screens from among the received images within the display.
1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or
RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the
picture becomes static (no longer moves), and a frame for picture cutting, as well as the message
that follows below, appear. Please press the button when the screen you want to register is
currently being displayed.
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)
button will eliminate the static state of the picture, and operations can be performed again from operation 1.
The frame can be moved using the
,
,
,
buttons. After designating the screen
you want to register, pressing the ENTER button will initiate screen registration. The registration
process takes approximately 1 minute to complete.
3. When the registration has been completed, the screen of the registered MyScreen, plus the
message, “MyScreen registration is finished,” will be displayed for several seconds, after which
the operation is terminated.
MyScreen Size
Selection of MyScreen display size:
x1
⇔
FULL
MyScreen Lock
Invalidation of MyScreen registration function:
TURN ON
⇔
TURN OFF
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in
this way, one can prohibit rewrites (“writeovers”) of the MyScreen.
27
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 6
MULTIFUNCTIONAL SETTINGS (continued)
OPTION Menu
With the OPTION menu, the five items shown in the Table below
can be performed.
Please perform each operation in accordance with the instructions
in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
12
: SELECT
Example : OPTION Menu
(VOLUME)
OPTION Menu
Item
VOLUME
28
Description
Adjust Volume: High
⇔
Low
AUTO OFF
Adjust AUTO OFF Time:
Long (MAX. 99 min.)
⇔
Short (Min. 1 min.)
⇔
(DISABLE: 0 min.)
The system automatically enters the standby mode if no signal is received
within the set time. This function is inactive when DISABLE (0 min.) is selected.
WHISPER
Select WHISPER Mode:
NORMAL
⇔
WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER
mode, acoustic noise and screen brightness are reduced.
LAMP TIME
Refer to LAMP TIME: When set, this function displays the total time the
projector lamp has been used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the lamp with a
new lamp, select RESET on the menu with the
button.
• Do not reset the lamp time unless you have replaced the lamp. And, always
reset the lamp time when replacing the lamp. The message functions will not
operate properly if the lamp time is not reset correctly.
• Before replacing the lamp, carefully read the descriptions headed "THE
LAMP".
FILTER TIME
Refer to FILTER TIME: This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the
button.
DEFAULT
⇔
CANCEL
• Do not reset the filter time unless you have cleaned or replaced the filter. And,
always reset the filter time when cleaning or replacing the filter. The message
functions will not operate properly if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 24
OPERATING THE PC SCREEN
You can use the remote control as a simplified mouse or keyboard.
CAUTION Mistaken use of the mouse/keyboard control could damage your equipment.
• Only connect to a PC.
• Before connecting, read the manuals of the device you will connect.
• Do not plug or unplug the connector cables while the computer is operating.
BLANK
STANDBY/ON
LASER
VIDEO
RGB
PS/2, ADB, Serial Mouse Control
1. Turn off the projector and PC power, and connect the projector’s
CONTROL terminal to the computer via the mouse cable.
2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control
function is given priority, and mouse control from the CONTROL terminal will not function.
3. Turn on the projector power, then the computer.
The functions in the table below can be controlled. If you have difficulty with control,
restart the computer (either from the software or by pressing the restart button).
Available Functions
AUTO
MENU
KEYSTONE
Remote Control Operation
Move Pointer
Use
Left click with mouse
Press
Disk Pad
Right click with mouse
Press
MOUSE/RIGHT button
Disk Pad
ENTER
POSITION
RESET
ASPECT FREEZE
ESC
MAGNIFY
ON
OFF
MUTE
USB Mouse Control
1. Connect the projector’s USB terminal to the computer using a USB cable.
The functions in the table below can be controlled.
Available Functions
Remote Control Operation
VOLUME
SEARCH
Move Pointer
Use
Left click with mouse
Press
Disk Pad
Right click with mouse
Press
MOUSE/RIGHT button
Disk Pad
NOTE
• It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.
track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and
select external mouse, and disable the pointing devices. In addition, the mouse may not function if the
computer does not have the needed utility program. See your computer’s hardware manual for details.
• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to
use the remote control, depending on the computer’s configurations and mouse drivers.
• The USB control can only be used for the functions listed above. You cannot do things like press two buttons
at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).
• This function is not available while the lamp is warming up (the POWER indicator flashes green), while adjusting the volume and
display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.
29
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 25
THE LAMP
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately:
78-6969-9464-5), then contact your local dealer. Before replacing the lamp, turn off the power,
and unplug the power cord, then wait at least 45 minutes, in order to ensure that the lamp is properly
cooled. Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.
WARNING The LCD projector uses a glass lamp bulb. It is a mercury lamp with
high internal pressure. High-pressure mercury lamps can break with a loud bang
bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a
different lifetime, and some may burst or burn out soon after you start using them. In
addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing,
and for gas containing mercury to escape from the projector’s vent holes.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the replace lamp indicator (see "Related Messages" ( 3 5 ) and "Regarding the
indicator Lamps" ( 3 6 )) comes on, replace the lamp as soon as possible. Using the
lamp for long periods of time, or past the replacement date, could cause it to burst. Do
not use old (used) lamps; this is a cause of breakage.
• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems
elsewhere besides the lamp. If this happens, contact your local dealer.
• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make
sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.
• If the lamp should break (it will make a loud bang when it does), unplug the power cord from
the outlet, and make sure to request a replacement lamp from your local dealer. Note that
shards of glass could damage the projector’s internals, or cause injury during handling, so
please do not try to clean the projector or replace the lamp yourself.
• Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used
bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.
• Do not use the projector with the lamp cover removed.
30
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 26
Replacing the lamp
All projector lamps will wear out eventually. If used for long periods of time, the image could become
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps
early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up
the projector, the lamp needs to be replaced. (See "Related Messages" ( 3 5 ) and "Regarding the
Indicator Lamps" ( 3 6 ) for details.)
1
witch the projector OFF,
remove the power cord from
the power outlet, and wait at
least 45 minutes for the unit
to cool.
2
Prepare a new lamp.
3
Check that the projector has
cooled sufficiently, and gently
turn it upside down.
4
5
6
Install the new lamp and
tighten the three screws
firmly. Also steadily push the
opposite side of the screwed
lamp into the unit.
Loosen the two screws as
shown in the diagram, and
remove the lamp cover.
7
Replace the lamp cover in
position and tighten the two
screws firmly.
Loosen the three screws, and
gently remove the lamp while
holding the grips. Touching
the inside of the lamp case
may result in uneven coloring.
8
Gently turn the projector rightside up.
ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
• Do not use with lamp cover removed.
• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing
the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
• When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER
WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following
operation within 10 minutes of switching power ON.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power
ON again. If the LAMP indicator is still red, replace the lamp.
31
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 27
THE AIR FILTER
Caring for the air filter
The air filter should be cleaned about every 100 hours. If the LAMP indicator and
TEMP indicator blink red simultaneously, or a message prompts you to clean the air
filter when you turn on the unit, the filter needs to be cleaned. (See "Related
Messages" ( 3 5 ) and "Regarding the Indicator Lamps" ( 3 6 ) for details.)
1
Turn off the projector, and unplug the power cord
2
Apply a vacuum cleaner to
the top of the air filter cover
to clean the air filter
Filter Cover
3
Turn on the projector, and use the menu to reset the filter
timer
• To reset the air filter timer, from the OPTION menu, select FILTER TIME.
32
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 28
Replacing the air filter
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be
replaced. Please contact your local dealer, after confirming the model of your
separately sold replacement air filter (sold separately: 78-8118-8896-1).
1
Turn off the projector, and unplug the power cord. Prepare a
new air filter (one specified for your projector)
2
Remove the air filter cover and air filter
3
Insert the new filter, and replace the
filter cover
4
Turn on the projector power, and using the menu, reset the
filter timer
• To reset the lamp timer, from the OPTION menu, select FILTER TIME.
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for
the unit. Please carefully read the "Product Safety Guide", in order to care for your projector correctly.
• Do not use with air filter cover removed.
• If the air filter becomes clogged by dust or the like, internal temperature rises and could cause
malfunction. The power is automatically turned off in order to prevent the unit from overheating
internally.
33
01CPX385SW/EN最終 02.11.20 9:30 AM ページ 29
THE HANDLE
Fixing the Handle
Fix the enclosed handle if you need.
1
Raise up the handle hook, and pass one
end of the handle through the hole of
handle hook.
2
Buckle the end of the handle, as the
right drawing.
3
Fix the other end of the handle to the
other handle hook in the same way.
CAUTION • Make sure the handle is fixed before carrying the projector with the
handle. If the projector should be dropped from the handle should be off, it could
result in an injury, and continued use could result in fire or electrical shock. Do not
flourish the projector with the handle.
OTHER CARE
Caring for the inside of the projector :
In order to ensure the safe use of your projector, please have it cleaned and inspected by
your local dealer about once every 2 years. Never try to care for the inside of the unit
yourself. Doing so is dangerous.
Caring for the lens :
Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the
lens directly with your hand.
Caring for the cabinet and remote control transmitter :
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a
neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly
with a soft, dry cloth.
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for
the unit. Please carefully read the "Product Safety Guide", in order to care for your projector
correctly.
• Do not use cleaners or chemicals other than those listed above, including benzene
and paint thinner.
• Do not use aerosols or sprays.
• Do not polish or wipe with hard objects.
34
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 7
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED
Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When
any such message is displayed on the screen, please respond as described below.
Message
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
(Note 1)
Description
Lamp usage time is approaching 2,000 hours. (Note 2)
Preparation of a new lamp, and an early lamp change, is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
(Note 1)
Lamp usage time is approaching 2,000 hours. A lamp change
within ** hours is recommended. (Note 2)
When lamp usage reaches 2,000 hours, the power will
automatically be turned OFF. Please change the lamp by
referring to “THE LAMP”. After you have changed the
lamp, please be sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
As lamp use has reached 2,000 hours, the power will soon be
automatically turned OFF. (Note 2)
Please immediately turn the power OFF, and follow the
instructions in the “THE LAMP”.
After you have changed the lamp, please be sure to reset the
lamp timer.
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.
NO INPUT IS DETECTED
ON ***
A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION
Menu, and perform reset of the filter timer.
There is no input signal.
Please confirm the signal input connection, and the status of the
signal source.
The horizontal or vertical wavelength of the inputted signal is
SYNC IS OUT OF RANGE
outside of the response parameters of this unit. Please confirm
ON *** fH *****kHz fV *****Hz the specs for this unit or the signal source specs.
The internal portion temperature is rising. Please turn the power
OFF, and allow the unit to cool down for approximately 20
minutes. After having confirmed the following items, then please
CHECK THE AIR FLOW
resent the power to ON.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
NOTE
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be
reappeared every time the power is turned ON.
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped
with an automatic shut-down function, such that the power will automatically be turned OFF
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior
to the functioning of the automatic shut-down function of this unit.
35
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 8
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Regarding the Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the
TEMP indicator have the meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
POWER
indicator
LAMP
indicator
TEMP
indicator
The orange Turned OFF Turned OFF
lamp is lighted (Not lighted) (Not lighted)
Description
The STANDBY mode is set
Flashing of the green lamp
Turned OFF
Turned OFF
The unit is warming up. Please wait.
The green lamp is lighted
Turned OFF
Turned OFF
The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp
Turned OFF
Turned OFF
Blinking of the
red lamp
-
-
The red lamp
Turned
OFF
The unit is cooling down. Please wait.
The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp has finished
flashing, and then perform the proper response measure using the item descriptions
below as reference.
The lamp does not light.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please change the lamp.
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp is
lighted, or
blinks
The green lamp
is lighted
The green
lamp is lighted
is lighted
Blinking of the
red lamp
Turned
OFF
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has
sufficiently cooled down, please make confirmation of the attachment state of the lamp and
lamp cover. After performing any needed maintenance, turn the power ON again; if the same
display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the
main unit has cooled down, please make confirmation that no foreign matter has become caught in
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display
red lamp
is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
Turned The red lamp is there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
lighted
OFF
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
There is a possibility that the interior portion has become overcooled. Please use the unit within
Alternative blinking
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
with the red lamp
service company.
Turned
OFF
Blinking of the
Simultaneous blinking
with the red lamp
This is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
NOTE
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,
and the indicator lamps may also be turned OFF. Press the “ ○” (power OFF) side of the main power switch, and wait
for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.
36
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 9
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Phenomenon
Power does not
come ON
No sound or
pictures are
outputted
Pictures are
displayed, but no
sounds are heard
Sounds are
heard, but no
pictures are
displayed
Colors have a fadedout appearance
Color tone is poor
Pictures appear
dark
Pictures appear
blurry
Cases not involving a machine defect
Items to be confirmed
Reference
Page(s)
The main power source is not ON.
Turn on the main power.
The electrical power cord is not plugged in.
The input changeover settings
are mismatched.
Correctly connect the power cord.
Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit 14
has sufficiently cooled down, turn ON the
power source.
Select the input signal, and
15
correct the settings.
No signal is being inputted.
Correctly connect the connection cord.
10, 11
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
10, 11
The volume setting has been set at (or
adjusted to) an extremely low level.
Adjust the VOLUME setting to a higher level.
17
The MUTE mode is the current setting.
Press the MUTE button to release
(change) the MUTE mode setting.
17
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
10, 11
The brightness setting has been set at
(or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a
brighter level.
24
The Slide lens door has not been removed.
Remove the Slide lens door.
14
Color depth setting or color tone setting
Perform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the
TINT settings, etc.
25
The brightness setting and/or contrast
setting has not been properly adjusted.
Perform picture adjustments by changing the
BRIGHT and/or CONTRAST settings, etc.
24
The WHISPER mode is the current
setting.
Change (by releasing) from the
WHISPER mode.
28
Lamp is approaching the end of its
product lifetime.
Exchange the old lamp with a new
lamp.
30, 31
Either the FOCUS setting or the H
PHASE is not properly adjusted.
Adjust the FOCUS and H PHASE settings.
15, 25
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.
3, 14
NOTE
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and
such do not constitute or imply a machine defect.
37
01CP-X385SW/Vol2-E 02.11.20 10:09 AM ページ 10
SPECIFICATIONS
NOTE • This specifications are subject to change without notice.
Item
Specification
Product name
Liquid
crystal
panel
Liquid crystal projector
Panel size
2.3 cm (0.9 type)
Drive system
TFT active matrix
Pixels
786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7 ~ 2.0 f=27.3 ~ 32.8 mm
Lamp
200 W UHB
Speaker
1.0W+1.0W (Stereo)
Power supply
AC100 ~ 120V, 3.3A / AC220 ~ 240V, 1.4A
Power consumption
310W
Temperature range
0 ~ 35°C (Operating)
Size
298 (W) x 94.6 (H) x228 (D) mm
Weight (mass)
3.25 kg
AUDIO port
AUDIO IN(Stereo) ..........2
AUDIO IN(R, L) ..............1
OUT port
RGB OUT........................1
AUDIO OUT ....................1
CONTROL port
CONTROL ......................1
USB ................................1
RGB port
RGB IN(1, 2) ..................2
VIDEO port
VIDEO IN ........................1
S-VIDEO IN ....................1
COMPONENT VIDEO
(Y, CB/PB,CR/PR) ......1
Port
228
241.5
Dimension Diagram
AC N
298
76
94.6
54
76.5
38
Unit : mm
ACCESSORIES
Accessories ................................................................ Part Number
UHB Lamp, 200W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9464-5
Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8896-1
Power Cable (US) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 78-8118-8102-4
Power Cable (UK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 78-8118-8101-6
Power Cable (Europe) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 78-8118-8103-2
RGB Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8708-8
Component Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8843-3
Video/Audio Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-3234-0
Stereo Mini Jack Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8846-6
Mouse Cable (PS/2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8105-7
Remote Control Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-9120-5
Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8673-4
Soft Carry Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9203-7
Not Included with Basic Packet ................................ Part Number
Ceiling Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9261-5
Adjustable Height Suspension . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-8312-7
Shipping Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-6969-9259-9
S-Video Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-3238-1
Mouse Cable (ADB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8106-5
Mouse Cable (Serial) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8107-3
Mouse Cable (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-8186-7
RS-232C Control Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-3312-4
Mac adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78-8118-3308-2
How to Order
Please order these parts through your dealer, or contact 3M Customer Service at the
following number:
In U.S. or Canada : 1-800-328-1371
In other locations, contact your local 3M sales office.
39
Intended Use
Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors,
using 3M lamps, 3M ceiling mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment
and/or create a potentially unsafe operating condition.
3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.
• 16˚ to 29˚C (60˚ to 85˚ F)
• 10- 80 %RH (without condensation)
• 0- 1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the
projector.
Use of this product in adverse conditions will void the product warranty.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only
transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call
us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.
3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
3M Canada
P.O. Box 5757
London, Ontario
N6A 4T1
DN00401 (QR56331_OG_ENG)
3M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
3M Europe
Boulevard de l'Oise
95006 Cerge Pontoise Cedex
France
Litho in Japan
© 3M 2002
78-6970-9169-8 Rev. A
Download PDF

advertising