Aarrow Fires AFS1221 Stove User Manual

Operating & Installation Manual
Wood / Multifuel Model Range
Ecoburn 7 Multifuel
PLEASE RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
BK043
Rev 6
October 2006
AFS1221
Congratulations on your choice of an Aarrow Stove.
More than 20 years experience has been put into the
development of our Ecoburn range to ensure ultimate
performance and years of trouble free enjoyment.
Every detail on this stove has been carefully engineered
and designed which is why we are so confident in the
reliability of our product that we offer a
Lifetime Guarantee.
Should you have any questions about our Ecoburn Stoves
that are not covered in this manual, please contact the
Aarrow dealer in your area, or call our Technical support
department on 01308 427234
© COPYRIGHT 2006
Arada Ltd
This booklet has copyright & may not be
copied in whole or part or be used for any
purpose other than that for which it is
supplied without express written consent
from Arada Limited.
2
Aarrow Ecoburn Wood & Multifuel Stoves
CONTENTS
INTRODUCTION
Warning Notice
Page
4
Safety Notices
5
The Principle Of The Fire
5
Check List
6-7
Fire Door Glass
23
Service Record
24
OPERATING INSTRUCTIONS
Fuel Types
25
Lighting The Fire
25
Solid Fuel Burning
26
Burning Wood
26
Technical Data
8
INSTALLATION
General Precautions
9
Handling
9
Mixed Fuels
26
Hearth
9
Anthracite
26
Combustible Materials
9
Overnight Burning
26
Air For Combustion
9
Air Inlet Controls - Primary Air
27
Fitting the Flue Outlet & Hotplate
10
Air Inlet Controls - Airwash
27
Fuel Retainer Bars
27
Multi-Purpose Operating Tool
28
Setting The Grate
28
De-Ashing (Riddle)
28
Empty The Ashpan
28
Ash Removal
28
Adjusting Air Inlet Controls
28
Main Fire Door Handle
29
Over-Firing
29
Extended Burning
29
OPTIONAL EXTRA ACCESSORIES
30
SPARE PARTS LIST
31 - 33
GUARANTEE
34 - 35
FINAL FACTORY CHECKLIST
36
Flues & Chimneys
10 - 13
Adjusting the Self Levelling Feet
14
Wood Only Version
14
Multifuel Version
15
Firebox Liner Panels
16
Optional Add In Boilers
17
Water Connections
17 - 18
Final Check List
19
SERVICING & MAINTENANCE
Cleaning - Internal Surfaces
20
Cleaning - Outer Finish
20
Chimney Sweeping
20
Annual Maintenance
21
Summer Storage / Non Usage
21
Door Adjustment
21
Dissassemble Airwash
22
Fuel Retaining Bars - Inspection
22
Aarrow Ecoburn Wood & Multifuel Stoves
3
WARNING
TO ALL MULTIFUEL USERS
PETROLEUM COKE
SOME OF WHOSE BRAND NAMES ARE
"CALCO", "PETROCOKE" OR "WONDERCO"
MUST NOT BE BURNED IN THIS APPLIANCE
TO USE THESE FUELS WILL INVALIDATE THE
APPLIANCE GUARANTEE
IF IN DOUBT CONTACT THE SOLID FUEL ASSOCIATION
TELEPHONE NUMBER 0800 600 000
www.solidfuel.co.uk
THE USE OF SPARE PARTS OTHER THAN THOSE SUPPLIED
BY AARROW FIRES WILL INVALIDATE THE
APPLIANCE GUARANTEE.
4
Aarrow Ecoburn Wood & Multifuel Stoves
INTRODUCTION
SAFETY
A fireguard conforming to BS 8423: 2002 should
be used in the presence of children and old/or
infirm people. If the appliance is used with the fire
door open, a spark guard conforming to BS 3248
should be fitted.
Caution Do not use aerosol sprays or any other flammable materials near the appliance under fire.
Do not fit an extractor fan in the same room as
the appliance.
Fire cement is caustic, hand and eye protection
should always be worn, prolonged contact with
the skin should be avoided.
Aarrow Fires Ltd will not be responsible for any
consequential or incidental loss or injury
however caused.
Before continuing any further with the installation
of this appliance please read the following guide to
manual handling.
• Always obtain assistance when lifting the
appliance.
• When lifting always keep your back
straight. Bend your legs not your back.
• Avoid twisting at the waist. It is better to
reposition your feet.
• Avoid upper body/top heavy bending. Do not
lean forwards or sideways when
handling the fire.
• Always grip with the palms of your hands.
Do not use fingertips for support.
• Always keep the stove as close to the body as
possible. This will minimise the cantilever
action.
• Use gloves to provide additional grip.
THE PRINCIPLE OF THE FIRE
Your Aarrow stove is built to the highest standard
of craftsmanship using the best materials and the
most modern equipment available. It is a highly
efficient and sophisticated piece of machinery and
when properly installed and operated it should provide a lifetime of heating satisfaction.
Aarrow Ecoburn Wood & Multifuel Stoves
Safety is the most important consideration when
installing your fire. If not properly installed and
operated a house fire may result. installation must
comply with the Building Regulations and conform
to all relevant fire safety standards.
Aarrow Fires produce a variety of appliances
ranging from units, which are traditional in style to
stoves which are modern in appearance, all
bristling with "High Tech" features.
Model types include simple room heaters,
convectors, integral boiler models and inset units.
Your Aarrow Stove, is constructed from either single or twin wall steel strengthened where necessary.
Cast iron is used where appropriate for decorative
features.
All fire doors are fitted with special high
temperature ceramic glass panels through which
the fire can be viewed.
Multifuel stoves are fitted with a cast iron grate to
give full multifuel facility and positive de-ashing.
All models except integral boiler models are lined
with firebricks or heat reflective panels which
ensure complete combustion and provide a good
heat store to even out fluctuations in burning.
An internal throat plate produces turbulence to
encourage secondary combustion and directs the
flue gas around the whole upper firebox before
allowing it to escape up the chimney.
On multifuel appliances the primary air for burning
enters the ash pit chamber beneath the grate,
controlled by the air inlet mechanism.
Aarrow stoves are also fitted with an "air wash" so
called because it provides a curtain of high speed
preheated air behind the glass to help keep it clean
and to provide secondary air/over draught.
The provision of two inlets on all multifuel stoves
gives a wide range of primary air/secondary air,
under draught/over draught combinations. The
optimum settings will only be established by
experience in firing the appliance, and will depend
on type of fuel, the position of the appliance in the
house, condition of chimney etc.
5
CHECK LIST
Part Description
ECB 5 ECB 5 ECB 7
& Visual Aid
Wood Multifuel Wood
(not to scale)
ECB 7
ECB 9
Multifuel Wood
ECB 9 ECB 11 ECB 11
Multifuel Wood Multifuel
1. Grate bars
N/A
5
N/A
7
N/A
9
N/A
11
1
N/A
1
N/A
1
N/A
1
N/A
1
1
1
1
1
1
1
1
2. Wood burning
tray
3. Stainless Steel
Throat plate
4. Flue spigot
1 (4”)
1 (4”)
1 (5”)
1 (5”)
1 (5”)
1 (5”)
1 (6”)
1 (6”)
1 (4”)
1(4”)
1(5”)
1(5”)
1 (5”)
1(5”)
1(6”)
1(6”)
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
5. Hotplate
6. Rear liner (s)
7. Side liners
6
Aarrow Ecoburn Wood & Multifuel Stoves
CHECK LIST
Part Description
ECB 5 ECB 5 ECB 7
& Visual Aid
Wood Multifuel Wood
(not to scale)
8. Rear grate bar
support
9. Comb
assembly
consisting
of comb & comb
extension
bar
ECB 7
Multifuel
ECB 9
Wood
ECB 9 ECB 11 ECB 11
Multifuel Wood Multifuel
N/A
1
N/A
1
N/A
1
N/A
1
N/A
1
N/A
1
N/A
1
N/A
1
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
10. Fuel retainers
11. Fire door handle - Nickel Plated
12. Stainless steel
Ashpan & Cover
13. Operating tool
14. Instruction
Manual
15. Stove Mitten
Aarrow Ecoburn Wood & Multifuel Stoves
7
TECHNICAL DATA
TECHNICAL DATA
Room Min/Max
Room Heater Only
Output (kW)
ECB 5
Wood
ECB 5
Multifuel
1-5
1-5
ECB 7 ECB 7 ECB 9
ECB 9 ECB 11 ECB 11
Wood Multifuel Wood Multifuel Wood Multifuel
1-7
1-7
2-9
2-9
2.5 - 11
2.5 - 11
Room Heater with Domestic Hot
Water with add in boiler type
0
0
8
8
9
9
10
10
Max Output to Room (kW)
3
3
4.8
4.8
6.7
6.7
7.6
7.6
Max Output to Water (kW)
2
2
2.2
2.2
2.3
2.3
3.4
3.4
522
558
558
600
600
605
605
476
476
586
586
672
672
Height (mm)
522
Width (mm)
397
Depth (mm) *
388
388
386
386
396
396
442
442
Height to Centre of Rear Flue
424
424
449
449
485
485
478.5
478.5
Depth from Back to Centre
of Flue (mm)
94
94
109
109
102.5
102.5
141
141
102mm
(4”)
127mm
(5”)
127mm
(5”)
64
68
Flue Diameter
Weight Packed (Kg)
102mm
(4”)
54
397
57
127mm 127mm
(5”)
(5”)
74
79
152mm 152mm
(6”)
(6”)
95
106
*Measured from rear of canopy to the tip of the handle.
The model and Serial Number of your stove can be found stamped into the casing,
centrally just below the bottom edge of the fire door aperture.
8
Aarrow Ecoburn Wood & Multifuel Stoves
INSTALLATION
GENERAL PRECAUTIONS
Note - All installations must conform to the
appropriate building regulations.
The Building Regulations for England and Wales
2000 ref Approved Document J 2002 edition
(issued by the DTLR).
The Building Standards (Scotland) (Consolidation)
Regulations.
Detailed recommendations for installation of
appliances, chimneys and flues are outlined in the
current issue of the following British Standards:BS6461, BS8303 and BS4543.
Any Manufacturer's Instructions must not be
taken as overriding statutory requirements.
During installation ensure that adequate
precautions are taken to avoid unnecessary risk to
yourself or any householder. In particular the
danger from the caustic nature of the fire cement
should be avoided by using these accepted
methods:
• Wear gloves when handling fire cement.
• Wear goggles when chiselling or looking up
chimneys.
Make sure that Building Regulations are adhered to
during installation along with any local by-laws. In
the case of heating systems make sure that the pipe
work is correctly bonded to ensure electrical
earthing.
HANDLING
By the time you read this you will appreciate the
weight of the appliance. The Safety and handling
guidelines as set out on page 5 of this manual
should be followed.
To make movement easier internal fittings, fuel
retainers, grates, firebox liners, flue outlets, hot
plate, throat plate, etc., can be removed.
HEARTH
The stove should be installed to stand on a
constructional hearth of non-combustible materials
not less than 125mm (5'') thick conforming to
Building Regulations. Dimensions of the hearth
should project at least 300mm (12'') forward of the
front of the appliance and 150mm (6'') at the sides.
The surface of the hearth should be free of
combustible materials. In most buildings with solid
concrete floors the requirement will be met by the
floor itself, but mark the perimeter of the hearth to
ensure floor coverings are kept well away or use
different levels to mark the hearth perimeter.
COMBUSTIBLE MATERIALS
A gap of at least 450mm (18'') should be allowed
between the appliance and any combustible
materials including furnishings. Adjacent walls
should be of suitable non-combustible
construction, preferably brickwork. In large
fireplaces take care that any supporting beam is
protected by a 13mm (0.5'') sheet of
Masterboard/Supalux spaced 13mm (0.5'') off the
surface with strips of non-combustible material
- not wood.
Make sure that there is a gap between an
uninsulated flue system and any combustible
material. This gap must be at least 3 x the outside
diameter of the flue pipe, or 1.5 x the flue diameter
to non combustible surfaces. see illustration p13.
AIR FOR COMBUSTION
There must always be a permanent means of
providing air for combustion into the room in
which the fire is installed. A permanent vent with a
total free area of at least 550mm for every kW
rated output above 5kw should be connected
directly to the outside air or to an adjacent room
which itself has a permanent vent of the same size
direct to the outside air. The fitting of an extractor
fan to either of these rooms is not recommended.
2
Care should be taken to make sure that the hinges
are not damaged during installation.
Aarrow Ecoburn Wood & Multifuel Stoves
9
INSTALLATION
FITTING THE FLUE OUTLET AND
HOT PLATE
The flue outlet spigot is found packed inside the
appliance. The hot plate (blanking plate) is supplied
fitted to the top opening and is removed by turning
clockwise (as is the flue outlet).
Smear a very thin layer of fire cement on the faces
of the flue outlet and the blanking plate. Fit the outlet to the appliance in the desired position .
Lock into place by rotating anti-clockwise and
tighten by tapping with a block of wood and mallet
from the inside of the appliance. Similarly, fit the
blanking plate to the unused opening. Clean off any
surplus fire cement.
Place appliance on the hearth and make sure that it
is level and does not rock. The Solution range of
stoves are fitted with adjustment cam on both rear
legs, see page 14 for details.
Connect the chimney ensuring all joints are sealed
with fire cement.
FLUES AND CHIMNEYS
Please remember that chimney draught is
dependent on four main factors:
• Flue gas temperature.
• Flue height.
• Flue size.
• Flue terminal.
The stove must be connected to a suitable and
efficient flue that provides a good up draught to
safely take the products of combustion (fumes)
from the stove outlet to the outside air. To ensure a
good up draught it is important that the flue gases
are kept warm and that the flue size suits the stove.
The termination of the outlet at the top of the flue
also needs to comply with the Building
Regulations. The minimum effective height of the
flue must be at least 4.5 metres from the top of the
stove to the top of the flue outlet. When warm the
flue draught should be between 0.1 and 0.2 mb.
A chimney may comply with the regulations but
still be subject to down draught and similar
problems. A chimney terminating above the ridge
level is generally less likely to suffer such
problems.
If a new chimney is being provided it should fully
comply with the relevant Building Regulations that
specify the requirements for solid fuel burning
installations. Suitable types of chimney include the
following.
*NOTE
THE FLUE PIPE MUST BE FITTED INSIDE THE OUTLET SPIGOT
FAILURE TO DO SO COULD RESULT IN THE SPILLAGE OF
CONDENSATION ECT. RUNNING DOWN THE FLUE.
Fig. 1. Flue and Spigot Fitting
Masonry chimney built with clay or concrete
liners, or a chimney block system meeting Building
Regulations. These types of chimney should be
installed in accordance with the Building
Regulations and BS 6461: Part 1.
Factory made insulated chimney complying
with BS 4543: Part 2 (often called "Class 1
prefabricated metal chimney"). These types of
chimney should be installed in accordance with the
Building Regulations and BS 7566: Parts 1 to 4.
10
Aarrow Ecoburn Wood & Multifuel Stoves
INSTALLATION
Due to the gradual introduction of European
Chimney Standards chimneys will be specified
according to their performance designation as
defined in BS EN 1443 that covers the General
Requirements for chimneys. The minimum
performance designation required for use with solid
fuel burning stoves is T450 N2 S D3.
The flue and chimney installation must be carefully
checked by a competent person before fitting the
stove to ensure it is suitable and will work safely.
If the chimney is old (i.e. built of brick or stone
without a liner) or being opened up for reuse
additional checks and smoke testing as described in
Appendix E of the Approved Document J 2002
Edition should also be carried out to ensure the flue
and chimney are in good operating condition.
Unless the existing flue is in good condition with
suitable access for collection and removal of debris.
If the flue size is more than 225mm (9 inches)
diameter or 200 x 200mm square, a suitable lining of
150mm (6 inches) diameter should be fitted, or if the
flue length is over 5.5 metres one size larger than the
appliance outlet should be fitted. This should be a
double skin stainless steel flexible flue liner that is
independently certified for use with solid fuel.
Details of suitable linings for use with solid fuel are
given in the Official HETAS guide that can be
viewed on their website at www.hetas.co.uk
It is also important that suitable flue pipe
complying with the Building Regulations is used to
connect the stove to the flue in the chimney and that
suitable access is provided into the flue for regular
inspection and sweeping of the flueways.
The installer should comply with the Building
Regulation requirements in respect of providing a
Notice Plate giving details on the chimney, flue
lining, hearth and fireplace installation. Approved
Document J of the Building Regulations for
England and Wales is available from The Stationery
Book
shops
and
can
also
be
viewed
at
the
ODPM
website
at
www.s af ety.odpm.gov.uk/bre gs/bra ds. h t m
Details on the relevant Building Regulations and
BS British Standards are given in the "General
Aarrow Ecoburn Wood & Multifuel Stoves
Precautions" section page 9 of these instructions.
A chimney may comply with the regulations but
still be subject to down draught and similar
problems. A chimney terminating above the ridge
level is generally less likely to suffer such
problems.
Chimneys should be as straight as possible.
Horizontal runs should be avoided except where
the rear outlet of the appliance is used, in which
case the horizontal section should not exceed
150mm (6'') in length.
If the fire appears to be working hard but produces
very little output to the room it is likely that
excessive draw is present in the chimney, and that
heat is being sucked out of the appliance and up the
chimney. If this is the case we recommend the
fitting of a draught stabiliser in preference to a flue
damper, in the interest of safety and efficiency.
We do not recommend the use of a damper when
burning solid fuel.
FOR ALL APPLIANCES
Access for cleaning the flue should be incorporated
in the system other than through the appliance (e.g.
a soot door or access through register plate).
Purpose-made soot doors and inspection lengths
are available from manufacturers of all systems.
Ensure that the whole length of the flue can be
reached from the soot door.
Note: if the appliance is fitted with a draught
stabiliser or if one is fitted to the flue pipe or
chimney in the same room as the appliance, then
the permanent air entry opening (or openings)
should be increased by 300mm2 for each kW of
rated output.
For advice on flues and chimneys contact;
NACE (National Association of Chimney
Engineer): telephone 0800 0924019
www.nace.org.uk
or
NACS (National Association of Chimney
Sweeps): telephone 01785 811732
www.chimneyworks.co.uk
11
INSTALLATION
Fig. 2. A Typical Rear Flue Layout
12
Aarrow Ecoburn Wood & Mutifuel Stoves
INSTALLATION
ADJUSTING THE SELF
LEVELLING FEET
WOOD STOVE VERSION WOOD TRAY
The Aarrow Ecoburn Wood and Multifuel stoves
are equipped with adjustable rear levelling feet,
these are ideal for use where the hearth surface is
not flat or level.
The wood burning tray should come fitted in your
stove, if not please follow these instructions -
Adjustment is as follows:
• Position the stove on the hearth into its final resting place, ensuring room for the flue connections
etc.
• On the rear leg of the stove, loosen the pozi screw,
and rotate the inner ‘cam’ shaped levelling foot
until this touches the hearth. (See Fig. 4.).
•Re-tighten the pozi screw. Check the stove is level
with a sprit level.
•Repeat for the other rear leg.
•Fully open the fire door, and remove the two round
fuel retaining bars,
•Locate the front of the wood tray, this is the end
with no tabs protruding from each side,opposite to
the rear end with the tabs protruding either
side.(See Fig. 5.)
•Holding the front edge of the wood tray, carefully
insert the wood tray into the firebox, taking care not
to damage the paint work and side / rear liner panels.
•Engage the rear lugs into the slots athe the rear of
the side landings. Then lower the front of the tray
until this rests onto the front brace of the stove.
(See Fig. 6.)
Front
Fig. 4. Adjusting the rear feet
Rear Lug
Fig. 5. Wood tray identification
Fig. 6. Wood Tray Installed
14
Aarrow Ecoburn Wood & Multifuel Stoves
INSTALLATION
MULTIFUEL STOVE VERSIONMULTIFUEL GRATE
GRATE
The grates in the Aarrow Ecoburn multifuel units
comprise a series of reciprocating cast iron bars
seated on a pivoted "comb". All bars in the grate are
identical, but every other bar is turned through 180
degrees, with the ends of the bars marked "H" sitting on the high sections of the comb, and the ends
marked "L" sitting on the low sections.
ASSEMBLING THE GRATE
Fig. 7. Fitting the grate bars
To assemble the grate, fit bars to low sections of the
comb first, inserting end marked "H" into rear
channel with groove on underside of bar located on
upstand tab, and then lowering end marked "L"
onto the low section of the comb, see fig. 7. The
upper bar is fitted in a similar manner, but with the
end marked "L" inserted in the rear channel, and
the end marked "H" seated on the high section of
the comb. See fig. 8. for the assembled grate layout.
GRATE BAR REPLACEMENT
After extended use it may be necessary to replace
some of the grate bars. Periodic inspection of the
bars is recommended and the removal of any nails
or wire that may be present after burning wood. All
the grate bars in each appliance are identical and
can easily be lifted out after removal of the fuel
retainers. Remove damaged grate bars and replace
with casting of the same type, fitting as per
instruction above. When re-ordering replacement
grate bars, see page 31of these instructions for the
correct spare part code.
Aarrow Ecoburn Wood & Multifuel Stoves
Fig. 8. Assembled grate
15
INSTALLATION
FIREBOX LINER PANELS
The Aarrow Ecoburn Wood and Multifuel stoves
use firebox liner panels to the sides and back of the
firebox. The throat plate sits on top of the side and
rear panels. These should come fitted to your stove,
if however they are not proceed as follows to fit
them as follows •Open the fire door.
•Remove the two round front fuel retaining bars, by
lifting one end free of the bracket and sliding the
remaining end out from the bracket.
Fig. 10. Liners inserted
•Set the small liner(s) into the back of the fire.
•Insert side liner panels. (See Fig. 10).
•Fit the throat plate with the single bend and two
cut outs to the front facing up. The projecting lugs
sit on top of the side liners. The long centre tab on
the back edge rests on the rear liners.The shorter
turn-down tabs against the vertical face.(See Fig.
11 & 12 ).
Fig. 11. Inserting the throat plate
•Replace the front fuel retainer bars.
Note: Neither the rear firebox liners nor the side
firebox liners are "handed", both faces are
suitable for direct contact with the fire.
Note: Cracking of lining panels does not effect
efficiency.
Fig. 12. Liners & throat plate
correctly fitted
Fig. 9. Overall View Of Liners & Throat
Plate.
16
Aarrow Ecoburn Wood & Multifuel Stoves
INSTALLATION
OPTIONAL ADD IN BOILERS
supplier will be able to offer advice and assistance.
Aarrow Ecoburn Wood and Multifuel stoves offer
the option of a slab boiler, which occupies the position of the rear firebox liner panels.
Direct Systems
Fitting:
•Remove the fuel retainering bars, rear firebox liner
panels and throat plate.
•Knock out the blanking discs in the back
plate corresponding to the terminals on the
boiler.
•Introduce the boiler to the appliance
through the main fire door and locate the
terminal pipes through the back plate holes
and seal around boiler terminals with fire
cement.
•Engage locking nuts to the thread of the
terminals and tighten to secure the boiler in
position, ready for connection to flow and
return pipes.
•Replace throat plate and the fuel retainering bars.
Note: On boilers the terminal which is
approximately flush with the edge of the boiler
and marked "TOP" must be fitted uppermost, to
prevent "Kettling".
WATER CONNECTIONS
Heating systems
The size of the heating system which can be run,
will depend on the output rating of the appliance. It
will be necessary to work out heat loss calculations
for the system proposed in order to establish the
kW/hr rating. An appliance that will meet this
figure can then be chosen; (for boiler outputs please
refer to the brochure).
Stainless steel boilers, either factory fitted or
retro-fitted as add-in boilers enable connection to
direct systems to be made without the need to
change the cylinder or to fit an expansion tank. This
applies to domestic water supply only and should
not be done when in an area with soft water. If
radiators are used then an indirect system must be
utilised.
To connect the cylinder use 28mm copper pipes.
Ensure that the pipes rise continuously to the
cylinder.
Ensure that the runs are not too long, i.e. 20ft
maximum each for flow and return. Install the
cylinder above the level of the fire, and as close to
it as possible. (the higher the cylinder the faster the
circulation). Ensure that no valves are present in the
circulating pipes.
Indirect Systems- The Domestic Hot Water
Circuit
In addition to providing hot water the primary
circuit is essential in providing a "heat leak" to
absorb excessive heat produced in the event of the
circulation pump shutting down.
Heat is produced in varying quantities while the
fire is alight and care must be taken to ensure that
effective circulation can occur around the primary
circuit to carry heat away and thus stop boiling. The
output of any radiator installed as a "heat leak"
should not be less than 10% of the rated output of
the appliance. The radiator should not be fitted
with a control valve.
The cylinder must be of the indirect type with a
minimum capacity of 110 litres, conforming to
BS 1566 part 1.
The constructional requirements of installing and
connecting the appliance also need to be taken into
account when selecting. Design and calculations
for individual heating systems should be carried out
by a qualified heating engineer. In many cases your
Aarrow Ecoburn Wood & Multifuel Stoves
17
INSTALLATION
Primary flow and return pipes should be 28mm
diameter. The cylinder should be installed at a
higher level than the appliance, and as close to it as
possible (the higher the cylinder the faster the
circulation). The flow and return pipes should not
be longer than 20ft each. Pipe runs should rise
continually from the boiler to the cylinder.
A radiator of approximately 25 sq.ft. should be
connected into the primary circuit, if installed in the
bathroom it provides a means of drying towels in
the summer.
Safety Vent Circuit
This circuit consists of a cold feed pipe, expansion
pipe, and expansion tank. The possibility that water
may boil can never be completely ruled out, and it
is therefore vital to ensure that cold water can be
supplied to the boiler and steam vented from it at all
times.
The expansion tank should have a capacity of at
least 7 % of the system's water capacity. The cold
water feed pipe should be at least 22mm diameter.
There must not be any shut off valves in the circuit.
Pipes should be run to avoid air locks. A spring
safety valve should be fitted to the expansion pipe
close to the boiler.
It is often possible, and is good practice, to utilise
the primary flow and return as part of the safety
circuit. The ball valve should have a copper ball.
The overflow pipe from the expansion tank should
be 28mm diameter copper. Pipes in unheated
spaces must be lagged.
FINAL CHECK
Before handing over the installation to the
customer it is strongly recommended that the
appliance is lit and the functioning of the chimney,
hot water and heating system is checked.
A checklist (Pre-lighting Checks) appears in the
Operating Instructions, but in addition to this the
installer should:
•Balance the radiators.
•Re-vent and ensure no air locks.
•Check the circulation round the primary
system and the heat leak radiator,
particularly when the pump is running, to
ensure circulation is not reversed.
•Be sure that the chimney is operating and
that ALL smoke and fumes are vented to
the atmosphere through the chimney
terminal.
•Check all joints and seals.
•Clean the outside of the appliance to
prevent any stains becoming burnt on.
•Check the flue draught which should read
1 - 2mm, or 0.1 - 0.2mbar.
The following details must be checked and
completed in full by the installer at the time of
installation. Please answer all questions as fully as
possible. Aarrow Fires can not be held responsible for chimney or installation.
HOT WATER SYSTEMS
Is the boiler cross-flowed?
YES / NO
Are the pipes correctly sized?
YES / NO
What is the calculated output
required to heat the system?
Is a heat leak fitted?
YES / NO
What is the return water temperature?
Is the pump thermostatically
controlled by a pipe stat?
YES / NO
What is the height and distance of the
hot water tank above the stove?
•Operate the heating system and set the
pump head.
18
Aarrow Ecoburn Wood & Multifuel Stoves
INSTALLATION
CHECKLIST
Hearths, Fireplaces, Flues and chimneys
This checklist is to ensure hearths, fireplaces, flues and chimneys are satisfactory, and to show what you have done to comply with the
requirements of The Building Regulations 2000 Approved Document J 2002.
1. Building address, where work has been carried out.......................................................................................................................................
.........................................................................................................................................................................................................................
2. Identification of hearth, fireplace chimney or flue
3. Firing capability: solid fuel/gas/.
4. Intended type of appliance.
State model and output.
5. Ventilation provisions for the appliance:
State type and area of permanently open vents.
6. Chimney or flue construction
a) State the type or make and whether new or existing.
b) internal flue size (and equivalent height, where
calculated - natural draught gas appliances only).
c) If clay or concrete flue liners used confirm that they are
correctly jointed with socket end uppermost and
state jointing materials used.
d) If an existing chimney has been refurbished with a
new liner, type or make of liner fitted.
e) Details of flue outlet terminal and diagram reference.
Outlet Details:
Complies with:
f) Number and angle of bends.
g) Provision for cleaning and recommended frequency.
7. Hearth. Form of construction. New or existing?
8. Inspection and testing after completion
Tests carried out by:
Tests and results
Flue
inspection
visual
sweeping
coring ball
smoke
Appliance (where included) spillage
I/we the undersigned confirm that the above details are correct. In my opinion, these works comply with the relevant requirements in
Part J of Schedule 1 to the Building regulations.
Print name and title....................................................................................................Profession..........................................................................
Capacity......................................................................................................................Telephone..........................................................................
Address............................................................................................................................................................Post code.......................................
Signed........................................................................................................Date.................................
Aarrow Ecoburn Wood & Multifuel Stoves
19
SERVICING & MAINTENANCE
CLEANING
INTERNAL SURFACES
IMPORTANT Under some circumstances soot can quickly build
up on the throat plate and adjacent areas. The throat
plate should be removed and checked monthly, and
any debris stripped off. Similarly, clean the upper
surface of the firebox. Refer to page 16 for instructions on the throat plate removal / inspections.
OUTER FINISH
The outside finish of the appliance is a durable high
temperature paint. It is best cleaned by brushing
down with a clean shoe brush. Do not allow
moisture to remain on the appliance whilst cold or
surface rust may form.
The high temperature paint should not require
attention for some time, depending on use. The
hotter the fire burns the sooner repainting will be
necessary. Aerosol tins of paint are available for
complete refurbishing. Before repainting make sure
that the fire is out and is cold.
•Remove the door glass.
•Lightly wire brush, or rub with wire wool, the
body of the appliance to remove any loose paint
powder.
•Mask or remove items such as brass work.
•Any adjacent brickwork, mantelpiece, hearth,
etc., should be carefully masked for quite a
distance around the appliance. (this precaution is
to prevent discolouration of the surrounding brick
work, wallpaper etc).
Re-spray in a well-ventilated area - avoid breathing
the vapour. Refer to safety instructions on paint
cans.
•When the paint is dry refit door glass and any
other parts previously removed.
•Leave the appliance for eight hours before
re-lighting.
•Burn slowly for the first four hours, then build up
heat gradually to cure the paint.
20
Note: Use only genuine Aarrow Fires touch-up
spray as some paints interact. This could ruin the
finish and invalidate the guarantee.
DOOR GLASS
The door glass should remain clear during normal
daytime burning. However under certain conditions-such
as burning at a low rate with damp wood, or overnight
burning, the glass may become somewhat blackened. To
remedy this, operate the appliance at a fast rate.
Alternatively when the stove is cold open the door and
clean the inside face of the glass with a damp cloth or
with glass cleaner (available from fire stockists). A piece
of cloth moistened with vinegar and dipped in wood ash
- not coal ash - will provide a good soft scourer to
remove the soot without scratching the glass.
CHIMNEY SWEEPING
Sweeping should be carried out with an appropriate
sized bristle brush and rods to suit chimney size and
type. As with all appliances regular sweeping of the flue
is essential to avoid the danger of blockage and the
escape of poisonous fumes. Access for cleaning should
also be incorporated in the chimney (e.g. soot door or
access through register plate).
Any existing chimney should be swept prior to
installation of the appliance, and swept again a
second time within one month of regular use after
installation to establish frequency of sweeping
required. This should be done by a competent
person such as a NACS chimney engineer who will
provide a Certificate of Chimney Sweeping.
Sweep the whole flue way, including the outlet, at
least twice per burning season. It is important that
the flue ways, flue pipe and chimney be cleaned
prior to lighting the fire after a prolonged
shut-down period.
If any damage or doubt over the flue or chimney
exists, DO NOT use the appliance until the chimney and connector have been inspected and any
damaged parts repaired or replaced. This should be
done by a competent person such as a HETAS registered engineer.
Aarrow Ecoburn Wood & Multifuel Stoves
SERVICE & MAINTENANCE
ANNUAL MAINTENANCE
It is important that your fire is regularly serviced in
accordance with these instructions. This should be
carried out at least annually by a qualified person
and should consist of the following.
Remove the fire lining(s), and throat plate, inspect
all gasketing on doors, glass etc. and re-order any
items that may need replacing, from your Aarrow
dealer. With a wire brush clean inside the appliance
paying particular attention to the small inlet holes
of the air wash on the inside of the stove, above the
fire door. Ensure the inside face of the fire door is
free of debris around the area of the primary air
inlet.
Sweep the chimney and confirm that it is sound.
Examine all joints in the flue pipe etc. and re-seal if
necessary.
SUMMER STORAGE/NON USAGE
Please ensure that your stove is left clean and moving components are well lubricated for the summer
months (during periods of prolonged non use). If
possible store the throat plate outside of the stove,
check all movable components, at regular intervals,
to ensure they are moving freely.
Allow air movement through the stove, by opening
the airwash and prinmary air inlet(s) controls to
about half way open or leave the door ajar. This will
allow a free flow of air through the appliance thus
preventing moisture and condensation forming
inside the stove and chimney. This preventative
maintenance will ensure your stove stays in the best
condition for the coming winter months.
DOOR ADJUSTMENT
Once the appliance has been under fire for a period
of time the fire door may appear to have moved out
of alignment with relation to the door aperture.
This is quite normal and due to the settling of the
casing.
The fire door can be re-aligned by the user as
follows:
•When the appliance is cold, open the fire door so
that it is at a right angle to the front face of the fire.
•Lift the fire door up off the hinges. .
•Gently tap the two hinge pins in a direction to
compensate for the misalignment.(Fig.13)
•Refit the door and check to ensure it now sits
square to the body; if not repeat above steps.
Raising the door as follows:
•When the appliance is cold, open the fire door so
that it is at a right angle to the front.
•Lift the fire door up off the hinges.
•Drop one washer on the top and bottom hinge pin
.
•Refit the door and check.
Please Note: There is no adjustment to the door
lock/catch assembly.
Fig. 13. Adjusting the door hinge
Aarrow Ecoburn Wood & Multifuel Stoves
21
SERVICING & MAINTENANCE
DISASSEMBLE AIRWASH
The Aarrow Ecoburn air wash may be disassembled for cleaning or adjustment. To achieve this, the
following procedure should be followed:
Note - This should only be carried out when the fire
is cold and unlit.
•Unscrew (Anti-clockwise) the airwash control
knob (Fig. 14).
•Move outer cover up by tapping each end of the
cover with a soft mallet.
Fig. 16. Inner slider removal
•Lift outer cover free from body, being careful not
to damage the ends of each lug (Fig. 15).
FUEL
RETAINER
INSPECTION
•Slide off the spacer tube from the centre stud and
retain for re-assembly.
Fuel retainering bars are supplied with the stove.
Periodically check for any bowing or heat warpage
to the fuel retaining bars and replace as necessary.
•Unscrew the inner slider and clean/replace
(Fig.16).
•Refit using the reverse of this procedure.
BARS
-
Note: This operation should only be carried out
when the appliance is unlit and cold.
Fig. 14. Unscrew control knob
Fig. 15. Lifting cover from body
22
Aarrow Ecoburn Wood & Multifuel Stoves
SERVICING & MAINTENANCE
FIRE DOOR GLASS
In the event of the door glass being broken it can
easily be replaced.
Note: This operation should only be carried out
when the appliance is unlit and cold.
•Replace the four retaining clips and bolts. Do not
over-tighten the bolts as damage may occur to the
glass (Fig.19) Re-place the door carefully over the
hinges and slot in place.
•The door should be lifted off the hinges so that
the operations can be carried out on a
workbench or similar level surface.
•Unscrew the four hex bolts, on the inside of the
door securing the retaining clips.
•Carefully remove any pieces of broken glass, and
sealing gasket wearing suitable gloves.
•Re-place the gaskets and line them up in
relation to the door frame. (Fig. 17)
Fig. 19. Tightening the glass clips
Fig. 17. Lining up the gasket
•Re-seat the new glass, ensuring the sealing gasket
is flat and in contact with the glass. (Fig. 18)
Fig. 18. Fitting the glass
Aarrow Ecoburn Wood & Multifuel Stoves
23
SERVICING & MAINTENANCE
Date of Visit
Company
Work Carried Out
Signature
Should you have any questions about your Ecoburn stove that is not covered in this manual please contact
your Aarrow Fires retailer.
Please keep all repair receipts safely.
Please ensure you have this manual available when an engineer visits as they will complete the service record
chart.
24
Aarrow Ecoburn Wood & Multifuel Stoves
OPERATING INSTRUCTIONS
FUEL TYPES
Wood- Any type of wood is suitable provided it is
well seasoned and has a moisture content below
20%. This usually implies that the timber has been
suitably stored to allow moisture to evaporate for at
least nine months in the case of soft woods, and at
least eighteen months in the case of hard wood. We
recommend that for general burning, wood should
be split into logs of no more than 130mm (5")
diameter.
Larger logs can be used for overnight burning.
Approval does not cover the use of other fuels
either alone or mixed with the suitable fuels listed
above, nor does it cover instructions for the use of
WARNING wet wood must not be used as this will
greatly contribute to the creation of tar and creosote
which may, in extreme cases, run down the
chimney in liquid form. This will seriously damage
both the chimney and the appliance, and increase
the risk of chimney fire.
Note: If you have sticky tar inside the appliance or
chimney your wood is 'Green' or too wet.
Recommended Reading:
"Wood as Fuel" available from the Forestry
Commission.
Peat- Can be used in turf or briquette form, but
again the moisture content must be low.
Paper- paper will burn successfully. Burn dry
paper only or chimney damage will occur.
NEVER BURN PLASTICS OR WASTE IN
YOUR STOVE.
Coal - Household coal produces a large amount of
ash and smoke. If used the appliance and chimney
will require frequent cleaning. Therefore soft house
coal is not recommended.
Recommended fuels are as follows:
The Hetas Ltd, "Three Tick" appliance approval
only covers the use of the following fuels in this
appliance; Phurnacite, Phurnacite Plus,
Centurion, Maxibrite, Extracite, Pureheat,
Blazebrite, Taybrite, Sunbrite (Doubles/Singles),
Anthracite (Large Nuts), and Welsh Dry Steam
Coal (Large/Small Nuts).
Aarrow Ecoburn Wood & Multifuel Stoves
25
OPERATING INSTRUCTIONS
ENSURE THAT YOU HAVE READ &
UNDERSTOOD THESE INSTRUCTIONS
BEFORE LIGHTING THE FIRE.
ALWAYS WEAR SUITABLE PROTECTIVE
FIRE GLOVES WHEN REFUELLING YOUR
STOVE.
SOLID FUEL
Version Only)
BURNING
(Multifuel
•Set the grate to ‘coal’ position.
•Ensure that the ash pan is in position and the fire
doors are closed.
•Set the air wash (secondary air) to one quarter
open position.
•Set the primary inlet to the fully open position
•Light in the normal manner with paper and
kindling, or use a fire lighters.
•If using a gas poker be sure to remove it
immediately when the fire is alight.
•When the fire is well alight regulate the burning
rate by adjusting the setting on the primary air
inlet control.
•The air wash can be opened sufficiently to keep
the door glass clean.
BURNING WOOD
•When burning wood on multifuel version set to
grate to wood burning position.
•If wood burning only version no further settings
are required.
•Set the air wash to fully open position.
•Proceed as for solid fuel but note the fire will burn
up and become established more quickly.
• Ensure primary air control is in the fully closed
position. Note some familiarisation may be
required due to fuel variation and some adjustment
may be necessary.
periods, consequently more care in setting the
controls and some familiarisation is necessary
when burning anthracite.
Use the smallest size fuel (Stovesse or Small Nuts).
Proceed as for manufactured smokeless fuel. Leave
the air inlet control open about a quarter or less.
Note: The high temperature paint acquires
durability by being "cured" during the initial
firings of the appliance. During this time, fumes
which are non-toxic, are emmitted, certain persons
may find they have an unpleasant or irritant effect.
Ensure that the area is well ventilated during this
time.
OVERNIGHT BURNING
The appliance will burn overnight provided:
•Sufficient fuel is placed in the firebox.
•The controls are set correctly.
•Excess draught is not present in the chimney.
•Close the door.
•If the fire goes out with unburnt fuel left in the
firebox increase the air opening slightly, and vice
versa.
In the morning
Open the air control fully until embers begin to
glow brightly and place pieces of fuel on the fire
until it is well established.
WARNING: When wood is burnt slowly in a
closed appliance it produces moisture and tar,
which will create condensation and deposits in the
chimney. This effect can be minimised by burning
hard for a short period, about 20 minutes, twice a day.
It is usually convenient to do this morning and night.
Note: To avoid chimney problems your fire should
not be burnt slowly for longer than 12 hours
without a period of fast burning.
MIXED FUELS (Multifuel Version Only)
•The grate can be set to either coal or wood
position depending on the main percentage of
the fuel to be burnt.
•As per coal but allow additional secondary air.
•The primary air inlet can be closed and burning
regulated by means of the air wash above the door.
ANTHRACITE (Multifuel Version Only)
Anthracite is more difficult to keep in for long
26
WARNING: Properly installed, with a suitable
flue and chimney and operated and maintained
this appliance will not emit fumes into the
dwelling. Occasional fumes from the de-ashing
and re-fuelling may occur. However, persistent
fume emission is potentially dangerous and must
be investigated by a Hetas registered installer.
Stop using the appliance if you smell fumes or
see smoke escaping.
Aarrow Ecoburn Wood & Multifuel Stoves
OPERATING INSTRUCTIONS
AIR INLET CONTROLS
Both Aarrow Ecoburn wood & multifuel stoves
have two air inlets:
•The primary air inlet providing under draught to
the base of the fire chamber through the control
slider located under the oval cover.
•The air wash system (so called because its
pre-heated high speed air washes across the inner
face of the door glass, keeping it clear), which
provides over draught.
AIRWASH SYSTEM
The air wash has an internal sliding plate with slots,
housed in a cover plate, and is located above the fire
door. Sliding the control knob to the right as far as it
will go achieves the fully open position. Sliding it to
the left will shut off the air inlet slots As shown in fig.
22 & 23.
PRIMARY AIR
Air enters the appliance through the control on the
bottom of the fire door. The Aarrow Ecoburn has a
single control knob which slides left to right.
Sliding the knob to the right (+), fig.21, will
increase the amount of air intake to the stove. To
decrease push knob to the left (-) as in fig. 20.
Fig. 22 Fully Closed
Fig. 23 Fully Open
Please Note Fig. 20 Closed Position
refer to page 26 to the type of
fuel being burnt, as the position of the air inlet controls are dependant upon the fuel varity being used.
Incorrect setting could cause an inefficient heat output and poor fuel consumption from the appliance.
FUEL RETAINER BARS
Fig. 21 Open Position
Fuel retainering bars are supplied with the stove.
For wood burning, the top fuel retaining bar may be
removed to afford a better view of the fire. Slide
and lift the bar until it is clear of the guides at each
side, and remove through the fire door opening.
The bars are symmetrical and of even lengths
making incorrect fitting impossible.
Note: This operation should only be carried out
when the appliance is unlit and cold.
Aarrow Ecoburn Wood & Multifuel Stoves
27
OPERATING INSTRUCTIONS
MULTI-PURPOSE
TOOL
OPERATING
Your Aarrow stove comes with a multi-purpose
operating tool, which is used for riddling, setting
the multifuel grate *, (fuel position) , adjusting the
air wash control knob and for the removal of the
ashpan.
SETTING THE GRATE
(*Multifuel Version Only)
To use the operating tool for setting the grate in the
coal burning position or the wood burning position,
place the tool over the external round bar extension
, found on the front right hand side of the stove,
(see Fig. 24.), move the lever to the desired position
as indicated upon the bracket fixed to the stove.
This lever is also used for de-ashing and riddling
TO EMPTY THE ASH PAN
The Ecoburn stoves are supplied with a unique ashpan cover to prevent ash dust from being dispersed
around the room when de-ashing. To remove the
ashpan , open the fire doors. Slide the ashpan cover
over the top of the ashpan, ensuring the two radius
holes are alinged with the slots in the ashpan. Fit
the fork end of the operating tool into the ash pan /
cover and remove from the ash pit chamber.
Empty the ash into a suitable container and replace
ashpan into the stove, withdraw the cover & operating tool and close the fire doors.
Fig. 25 Operating Tool & Ashpan
Warning: The ash can be very hot. Empty only
into a metal container. Even if the ash appears
cold, red-hot pieces of ash may be concealed and
could easily start a fire or cause an injury.
ASH REMOVAL
Fig. 24 Setting The Grate
DE-ASHING (RIDDLE)
It is necessary to maintain an ash layer on the upper
surface of the grate bars, in order to protect them so
de-ashing should cease as soon as the first red
embers drop into the ash pan. Further de-ashing
will cause heat build-up under the grate, which will
considerably shorten its life. This operation should
be carried out with the doors closed to prevent dust
escaping into the room.
•Move up and down vigorously the riddling
lever (ash will fall into the ash pan beneath
the grate). See Fig. 24.
•When de-ashing is complete re-set grate to
previous position.
• Empty the ash pan.
The ash pan should be emptied at least twice a day
or when the level of ash reaches the top of the ash
pan. On no account should the ash be allowed to
build up to touch the underside of the grate bars as
this will greatly shorten their life span.
When the appliance is burning Wood only, it is
acceptable to maintain an ash bed on top of the
wood tray, of approximately 20mm (3/4'') without
any un-due effect upon the tray.
AIR WASH CONTROL KNOB
The operating tool can also be used to adjust the air
wash control knob. Use the fork end of the tool,
place side onto the knob and push in the desired
direction as in Fig. 26.
Note: Do not force the riddling lever.
Fig. 26 Adjusting Airwash Controls
28
Aarrow Ecoburn Wood & Multifuel Stoves
OPERATING INSTRUCTIONS
MAIN FIRE DOOR HANDLE
A stove mitten is supplied with your Aarrow
Ecoburn stove, this is provided for the operation of
the fire door handle whilst the stove is in use. Care
must be taken when opening and closing the fire
door as any surrounding areas of the stove will be
very hot.
Warning : Never attempt to open the fire door
whilst the appliance is in use, without the use of
the stove mitten or suitable gloves, serious
injuries may occur.
Caution must be given when re-fuelling the
appliance, always keep the stove mitten away
from naked flames and sparks.
OVER-FIRING
Do not over fire your appliance. Using flammable
liquids or too much wood or firing the fire at
maximum for prolonged periods may result in
over-firing. If the chimney connector or casing
glows red it is being over-fired. If this occurs
immediately close all air inlets to the appliance to
reduce the air supply to the fire. Should a chimney
fire occur immediately close the appliance down.
Get everyone out of the house and call the fire
brigade. A chimney fire may cause structural
damage of the chimney. Do not use the appliance
until the chimney and connector have been
inspected and any damaged parts repaired or
replaced. This should be done by a competent person
such as a HETAS registered engineer.
CLINKER
The formation of clinker suggests that the unit is
being over-fired. Any clinker forming on the grate
should be removed when cold.
EXTENDED BURNING
The appliance will burn for an extended period
provided:
•Sufficient fuel is placed in the firebox.
•The controls are set correctly.
•Excess draught is not present in the chimney.
•Fire door is closed.
•If the fire goes out with unburnt fuel left in
the firebox increase the air opening slightly,
and vice versa.
Aarrow Ecoburn Wood & Multifuel Stoves
In the morning
•Open the air control fully until embers begin
to glow brightly and place pieces of fuel on
the fire until it is well established.
WARNING: When wood is burnt slowly in a
closed appliance it produces moisture and tar,
which will create condensation and deposits in the
chimney. This effect can be minimised by burning
hard for a short period, about 20 minutes, twice a
day. It is usually convenient to do this morning and
night.
Note: To avoid chimney problems your fire should
not be burnt slowly for longer than 12 hours
without a period of fast burning.
WARNING: Properly installed, with a suitable
flue and chimney correctly operated and maintained this appliance will not emit fumes into the
dwelling. Occasional fumes from the de-ashing
and re-fuelling may occur. However, persistent
fume emission is potentially dangerous and must
be investigated by a Hetas registered installer.
Stop using the appliance if you smell fumes or
see smoke escaping.
If fume emission does persist, the following
immediate actions should be taken.
•Open doors and windows to ventilate room.
•Let the fire die or extinguish and safely
dispose of fuel from the appliance.
•Check the flue or chimney for a blockage, and
clean if required.
Seek expert advice from your HETAS registered
installer. Do not attempt to re-light the fire until the
cause of the fume emission has been identified and
corrected
29
OPTIONAL EXTRA / ACCESSORIES
ECB 9 ECB 9 ECB 11 ECB 11
Wood Multifuel Wood Multifuel
Optional Extra
Description
ECB 5 ECB 5 ECB 7
Wood Multifuel Wood
Aerosol Paint
AFS
101a
AFS
101a
AFS
101a
AFS
101a
AFS
101a
AFS
101a
AFS
101a
AFS
101a
ECB5
TRACE
G
ECB5
TRACE
G
ECB7
TRACE
G
ECB7
TRACE
G
ECB9
TRACE
G
ECB9
TRACE
G
ECB9
TRACE
G
ECB9
TRACE
G
ECB5
TRACE
L
ECB5
TRACE
L
ECB7
TRACE
L
ECB7
TRACE
L
ECB9
TRACE
L
ECB9
TRACE
L
ECB9
TRACE
L
ECB9
TRACE
L
AIB 0
AIB 0
AIB 8
AIB 8
AIB 9
AIB 9
AIB 10
AIB 10
AFS997
AFS997
AFS997
AFS997
AFS997
AFS997
AFS997
AFS997
AFS
1135
AFS
1135
AFS
1135
AFS
1135
AFS
1135
AFS
1135
AFS
1135
AFS
1135
ECB5
STAND
ECB5
STAND
ECB7
STAND
ECB7
STAND
ECB9
STAND
ECB9
STAND
N/A
N/A
AOC
XSL
AOC
XSL
AOC
SL
AOC
SL
AOC
ML
AOC
ML
AOC
LL
AOC
LL
Add On High
Canopy
N/A
N/A
AOC
SH
AOC
SH
AOC
MH
AOC
MH
AOC
LH
AOC
LH
Kooler To Touch
Fire Door Handle
AFS
1305
AFS
1305
AFS
1305
AFS
1305
AFS
1305
AFS
1305
AFS
1305
AFS
1305
N/A
N/A
ECB 7
Multifuel
Gothic Tracery
Lattice Tracery
Add In Boiler**
Stove Gloves
Floor Fixing Kit
Stand *
Add On Low
Canopy
Convector Kit
ECB7
ECB5
ECB5
ECB7
CONKIT CONKIT CONKIT CONKIT
ECB9
ECB9
CONKIT CONKIT
Note
* - The overall height of the stand is 160mm. This increases the combined height of stove
and stand by 100mm. This will effect the height from the floor to the centre of the rear
flue outlet, just add 100mm to rear flue outlet, see page 8 for technical information.
** - See page 17 for instructions on how to fit the add in boilers.
30
Aarrow Ecoburn Wood & Multifuel Stoves
SPARE PARTS LIST
Part Description
ECB 5 ECB 5 ECB 7
& Visual Aid
Wood Multifuel Wood
(not to scale)
ECB 7
ECB 9
Multifuel Wood
ECB 9 ECB 11 ECB 11
Multifuel Wood Multifuel
1. Grate bars
N/A
AFS001
N/A
AFS001
N/A
AFS001
N/A
AFS002
AFS
1196
N/A
AFS
1197
N/A
AFS
1198
N/A
AFS
1247
N/A
AFS
1193
AFS
1193
AFS
1194
AFS
1194
AFS
1195
AFS
1195
AFS
1248
AFS
1248
AFS
009a
AFS
009a
AFS
010
AFS
010
AFS
010
AFS
010
AFS
011
AFS
011
AFGS
064
AFGS
064
AFS
009
AFS
009
AFS
009
AFS
009
AFS
012
AFS
012
AFS
1207
AFS
1207
AFS
1210
AFS
1210
AFS
1213
AFS
1213
AFS
1244
AFS
1244
AFS
1206
AFS
1206
AFS
1209
AFS
1209
AFS
1212
AFS
1212
AFS
1243
AFS
1243
2. Wood burning
tray
3. Stainless steel
throat plate
4. Flue spigot
5. Hotplate
6. Rear liner(s)
7. Side liners
Aarrow Ecoburn Wood & Multifuel Stoves
31
SPARE PARTS LIST
Part Description
ECB 5 ECB 5 ECB 7
& Visual Aid
Wood Multifuel Wood
(not to scale)
ECB 7
Multifuel
ECB 9
ECB 9 ECB 11 ECB 11
Wood Multifuel Wood Multifuel
8. Liner Set
9. Stainless steel
ashpan
AFS
1205
AFS
1205
AFS
1208
AFS
1208
AFS
1211
AFS
1211
AFS
1242
AFS
1242
AFS
1199
AFS
1199
AFS
1200
AFS
1200
AFS
1201
AFS
1201
AFS
1249
AFS
1249
AFS
1190
AFS
1190
AFS
1192
AFS
1192
AFS
1191
AFS
1191
AFS
1240
AFS
1240
AFS
008
AFS
008
AFS
008
AFS
008
AFS
008
AFS
008
AFS
008
AFS
008
AFS
1214
AFS
1214
AFS
1215
AFS
1215
AFS
1216
AFS
1216
AFS
1216
AFS
1216
AFS
1010
AFS
1010
AFS
1010
AFS
1010
AFS
1010
AFS
1010
AFS
1010
AFS
1010
AFS
047
AFS
047
AFS
047
AFS
047
AFS
047
AFS
047
AFS
047
AFS
047
AFS
1293
AFS
1293
AFS
1293
AFS
1293
AFS
1293
AFS
1293
AFS
1293
AFS
1293
AFS
1202
AFS
1202
AFS
1203
AFS
1203
AFS
1204
AFS
1204
AFS
1252
AFS
1252
10. Fuel Retainer
11. Operating
Tool
12. Replacement
Glass & Gasket
13. Glass Clips
14. Hinge &
Fixing Kit
15. Air Wash
Assembly
16. Ashpan Cover
32
Aarrow Ecoburn Wood & Multifuel Stoves
SPARE PARTS LIST
Part Description
ECB 5 ECB 5 ECB 7
& Visual Aid
Wood Multifuel Wood
(not to scale)
17. Fire Door
Rope Kit
Complete With
Glue
18.Main Fire
Door Assembly,
Complete With
Handle, Glass,
Gaskets, Clips &
Seal
19. Door Handle
Assembly
AFS
1021
AFS
1021
ECB 7
Multifuel
ECB 9 ECB 11 ECB 11
ECB 9
Wood Multifuel Wood Multifuel
AFS
1021
AFS
1021
AFS
1021
AFS
1021
AFS
1021
AFS
1021
AFS
1218
AFS
1218
AFS
1219
AFS
1219
AFS
1220
AFS
1220
AFS
1220
AFS
1220
AFS
1306
AFS
1306
AFS
1306
AFS
1306
AFS
1306
AFS
1306
AFS
1306
AFS
1306
AFS
1121
AFS
1121
AFS
1121
AFS
1121
AFS
1121
AFS
1121
AFS
1121
AFS
1121
N/A
AFS
1226
N/A
AFS
1227
N/A
AFS
1228
N/A
AFS
1250
N/A
AFS
1229
N/A
AFS
1230
N/A
AFS
1231
N/A
AFS
1251
AFS
1285
AFS
1285
AFS
1285
AFS
1285
AFS
1285
AFS
1285
AFS
1285
AFS
1285
20. Replacement
Instructions
21. Comb &
Extension
22. Grate Bar
Support
23. Stove Mitten
Aarrow Ecoburn Wood & Multifuel Stoves
33
GUARANTEE
Guarantee
Once again we would like to thank you for buying
an Aarrow Ecoburn stove.
When you buy an Aarrow stove, you are not only
buying a first class appliance - you are buying a
commitment from us to look after you and your
appliance for as long as you want.
The Ecoburn stoves come with a
Lifetime
Guarantee
USE OF SPARE PARTS OTHER THAN
THOSE SUPPLIED BY AARROW WILL
INVALIDATE THE APPLIANCE WARRANTY.
AARROW WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR
INCIDENTAL LOSS, DAMAGE OR
INJURY HOWEVER CAUSED.
against splitting or cracking of the
main body. The main body being defined as the
steel outer casing and items fixed immovably to the
casing. All other parts are covered by a one-year
no-quibble parts Guarantee.
All Guarantee periods commence on the date of
purchase and are non-transferable.
This Guarantee shall not apply to any part that has
been altered in any way, or which in our judgment
has been subjected to misuse, neglect, accident,
abuse and fair wear and tear.
If you think your fire is not working correctly or in
the event of a breakdown, please call your local
dealer.
When you contact them, they will want to know:
Items which would be subject to fair wear or tear,
firebox liner panels, fuel retainers, throat plate,
door rope, door glass and gaskets are not covered
by the guarantee. However, should you have any
problems with your appliance please contact your
Aarrow stockist who will have the knowledge and
facilities to help you.
1.Your Name, Address/Post Code and Telephone
Number
2.Serial Number
3.Clear and concise details of the fault
Claims are not valid where the installation does
not conform to local Building Regulations and
fire codes.
The Guarantee is conditional upon the appliance
being serviced and checked annually by a qualified
heating engineer.
The Manufacturers decision shall be final.
Our Lifetime Guarantee is offered as an addition to
your statutory rights.
This installation and operating manual gives sufficient details to enable the appliance to be installed
and maintained. If further information is required,
our technical helpline will be pleased to help.
Please telephone 01308 427234 or email :
info@arada.uk.com
Please Note The appliance serial number can be found
stamped into the the casing of the main stove
body, centrally just below the bottom edge of the
fire box apperature.
If your appliance proves to be defective as a
result of faulty materials or workmanship
during the guarantee period, we will repair or
replace it FREE OF CHARGE as long as the fire
has been installed according to the manuals
instructions and the Final Installation Check
List on page 19 has been completed and signed
by a suitably qualified engineer.
34
Aarrow Ecoburn Wood & Multifuel Stoves
Lifetime Guarantee
For your peace of mind
Aarrow Fires gives a Lifetime Guarantee against manufacturing defects of the main
body* of its Ecoburn range of stoves. Additionally, all other parts are covered by a
one year no quibble replacement guarantee. This guarantee covers replacement of
the item only and does not extend to any other costs, including labour, incurred in its
replacement. Documentation must be retained and produced in the event of a
warranty claim. This guarantee specifically does not cover accidental damage, misuse, wear & tear. The use of non Aarrow replacement parts will invalidate your warranty. For full details contact your local Aarrow Fires retailer. All guarantees are in
addition to your statutory rights. Please see page 34 for further information regarding the lifetime guarantee.
*The main body defined as the steel outer casing and items fixed immovably on to this casing.
Aarrow Ecoburn Wood & Multifuel Stoves
35
FINAL FACTORY CHECK LIST
Model..................................
Serial No.............................
QUALITY
FINISH
I’ve checked it
and it’s O.K.
PARTS
FLUE OUTLET
HOT PLATE
FUEL RETAINERS
GRATE BARS / WOODBURNING TRAY
FIREBOX LININGS
Assembled by.............................
THROAT PLATE
Checked by ................................
AIR WASH
DOOR CATCH / NICKEL PLATED HANDLE
ASH PAN & COVER
ADJUSTING FEET X 2
OPERATING TOOL
CONVECTOR KIT FIXINGS X 4
OPERATING INSTRUCTIONS
STOVE MITTEN
Date of Purchase....................................
Name and address of supplier.......................................................................
.......................................................................................................................
.......................................................................................................................
Arada Ltd
The Fireworks
Bridport
Dorset
DT6 3BE
United Kingdom
Tel: +44 (0)1308 427234 Fax: +44 (0)1308 423441 www.arada.uk.com
BK043