Owner`s manual | Aastra Telecom 480I Telephone User Manual

Owner’s Manual
Integrated High Definition
LCD Television
HIGH-DEFINITION TELEVISION
32RV525RZ
37RV52R
37RV52RZ
37RV525RZ
40RV52R
40RV52RZ
For an overview of steps for setting up your new TV, see page 10.
Note: To display a High Definition picture, the TV must be receiving
a High Definition signal (such as an over-the-air High Definition
TV broadcast, a High Definition digital cable program, or a High
Definition digital satellite program). For details, please contact
your TV antenna installer, cable provider, or satellite provider.
© 2009 TOSHIBA CORPORATION
All Rights Reserved
40RV525R
40RV525RZ
46RV525R
46RV525RZ
Owner’s Record
The model number and serial number are on the back
of your TV. Record these numbers in the spaces below.
Refer to these numbers whenever you communicate
with your Toshiba dealer about this TV.
Model number:
Serial number:
HDA51B4002I
Dear Customer,
Thank you for purchasing this Toshiba LCD TV. This
manual will help you use the many exciting features
of your new LCD TV. Before operating your LCD TV,
please read this manual completely, and keep it
nearby for future reference.
Safety Precautions
WARNING: TO REDUCE THE RISK OF FIRE
OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
WARNING
RISK OF ELECTRIC
SHOCK DO NOT OPEN.
WARNING: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
WARNING
To prevent injury, this apparatus must be securely
attached to the floor/wall in accordance with the
installation instructions. See item 23 on page 4.
WARNING: If you decide to wall mount this
television, always use a UL Listed wall bracket
appropriate for the size and weight of this television.
The use of any wall bracket other than a UL Listed
wall bracket appropriate for the size and weight of this
television for wall mounting this television could result
in serious bodily injury and/or property damage. See
“Removing the Pedestal Stand” ( page 6).
NOTE TO CATV INSTALLERS
This is a reminder to call the CATV system installer’s
attention to Article 820-40 of the U.S. NEC, which
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding system of the building,
as close to the point of cable entry as practical. For
additional antenna grounding information, see items
30 and 31 on page 4.
2
CHILD SAFETY:
It Makes A Difference How and Where You Use Your Flat
Panel Display
Congratulations on your purchase! As you enjoy your
new product, please keep these safety tips in mind:
The Issue
• The home theater entertainment experience is a growing trend
and larger flat panel displays are popular purchases. However,
flat panel displays are not always supported on the proper stands
or installed according to the manufacturer’s recommendations.
• Flat panel displays that are
inappropriately situated on dressers,
bookcases, shelves, desks,
speakers, chests or carts may fall
over and cause injury.
TOSHIBA Cares!
• The consumer electronics industry
is committed to making home
entertainment enjoyable and safe.
Tune Into Safety
• One size does NOT fit all. Follow the manufacturer’s recommendations
for the safe installation and use of your flat panel display.
• Carefully read and understand all enclosed instructions for
proper use of this product.
• Don’t allow children to climb on or play with furniture and
television sets.
• Don’t place flat panel displays on
furniture that can easily be used as
steps, such as a chest of drawers.
• Remember that children can
become excited while watching a
program, especially on a “larger
than life” flat panel display. Care
should be taken to place or install
the display where it cannot be
pushed, pulled over, or knocked down.
• Care should be taken to route all cords and
cables connected to the flat panel display so that they cannot be
pulled or grabbed by curious children.
Wall Mounting: If you decide to wall mount your
flat panel display, always:
• Use a mount that has been recommended by the display
manufacturer and/or listed by an independent laboratory (such
as UL, CSA, ETL).
• Follow all instructions supplied by the display and wall mount
manufacturers.
• If you have any doubts about your ability to safely install your
flat panel display, contact your retailer about professional
installation.
• Make sure that the wall where you are mounting the display is
appropriate. Some wall mounts are not designed to be mounted
to walls with steel studs or old cinder block construction. If you
are unsure, contact a professional
installer.
• A minimum of two people are
required for installation. Flat panel
displays can be heavy.
• NEVER allow your body to come in contact
with any broken glass or liquid from the
damaged television. The LCD panel inside the
TV contains glass and a toxic liquid. If the
liquid comes in contact with your mouth or
eyes, or your skin is cut by broken glass, rinse
the affected area thoroughly with water and
consult your doctor.
• ALWAYS contact a service technician to inspect
the TV any time it has been damaged or dropped.
Important Safety Instructions
1)
2)
3)
4)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding type plug. A polarized Wide blade
plug has two blades with one wider
than the other. A grounding type
plug has two blades and a third
grounding prong. The wide blade or
the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched, particularly at plugs,
convenience receptacles, and the point
where they exit from the apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer,
or sold with the apparatus. When a
cart is used, use caution when moving
the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.
Additional Safety Precautions
14a)CAUTION: If the TV is dropped and the cabinet or
enclosure surface has been damaged or the TV does
not operate normally, take the following precautions:
• ALWAYS turn off the TV and unplug the power
cord to avoid possible electric shock or fire.
15) CAUTION:
• To reduce the risk of electric shock, do not
use the polarized plug with an extension cord,
receptacle, or other outlet unless the blades
can be inserted completely to prevent blade
exposure.
• To prevent electric shock, match wide blade of
plug to wide slot; fully insert.
16) WARNING:
To prevent the spread of fire, keep candles or other
open flames away from this product at all times.
Installation, Care, and Service
Installation
Follow these recommendations and precautions and
heed all warnings when installing your TV:
17) WARNING: NEVER expose batteries to excessive
heat such as sunshine, fire or the like.
18)
ALWAYS plug the product into an outlet
that is located in such a manner that
it can be easily unplugged in case the
product requires service.
19) NEVER route the product’s power cord inside a wall
or similar enclosed area.
20) Never modify this equipment. Changes or
modifications may void: a) the warranty, and b) the
user’s authority to operate this equipment under the
rules of the Federal Communications Commission.
21)
DANGER: RISK OF SERIOUS PERSONAL
INJURY, DEATH, OR EQUIPMENT
DAMAGE!
Never place the TV on an unstable
cart, stand, or table. The TV may
fall, causing serious personal
injury, death, or serious damage
to the TV.
22) To avoid damage to this product, never place or store
the TV in direct sunlight; hot, humid areas; or areas
subject to excessive dust or vibration.
(continued)
3
23) Always place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the unit.
To secure the TV, use a sturdy strap from the hook(s)
on the rear of the TV to a wall stud, pillar, or other
immovable structure. Make sure the strap is tight,
secure, and parallel to the floor.
31)
• Use extreme care to make sure you are never
in a position where your body (or any item
you are in contact with, such as a ladder or
screwdriver) can accidentally touch overhead
power lines. Never locate the antenna near
overhead power lines or other electrical
circuits.
• Never attempt to install any of the following
during lightning activity: a) an antenna
system; or b) cables, wires, or any home
theater component connected to an antenna
or phone system.
Sturdy strap (as short as possible)
4"
min.
TV side
Hook
TV top
24) The apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such
as vases, shall be placed on the apparatus.
25) Never block or cover the slots or openings in the TV
cabinet back, bottom, and sides. Never place the TV:
• on a bed, sofa, rug, or
similar surface;
• too close to drapes,
curtains, or walls; or
• in a confined space such
as a bookcase, built-in
cabinet, or any other place with poor ventilation.
The slots and openings are provided to protect the
TV from overheating and to help maintain reliable
operation of the TV. Leave a space of at least 4 (four)
inches around the TV.
26) Always place the back of the television at least four
(4) inches away from any vertical surface (such as a
wall) to allow proper ventilation.
27) Never allow anything to rest on or roll over the power
cord, and never place the TV where the power cord is
subject to wear or abuse.
28) Never overload wall outlets and extension cords.
29) Always operate this equipment from a 120 VAC, 60
Hz power source only.
30) Always make sure the antenna system is properly
grounded to provide adequate protection against
voltage surges and built-up static charges (see
Section 810 of the National Electric Code).
Antenna lead-in wire
Ground clamp
Electric service
equipment
Ground clamps
Antenna discharge unit
(NEC Section 810-20)
Grounding conductors
(NEC Section 810-21)
Power service grounding
electrode system
(NEC Art 250 Part-H)
DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
Care
For better performance and safer operation of your TOSHIBA
TV, follow these recommendations and precautions:
32) If you use the TV in a room whose temperature is
32 °F (0 °C) or below, the picture brightness may
vary until the LCD warms up. This is not a sign of
malfunction.
33) Always unplug the TV before cleaning. Gently wipe
the display panel surface (the TV screen) using a dry,
soft cloth only (cotton, flannel, etc.). A hard cloth
may damage the surface of the panel. Avoid contact
with alcohol, thinner,
benzene, acidic or alkaline
solvent cleaners, abrasive
cleaners, or chemical
cloths, which may damage
the surface. Never spray
volatile compounds such as insecticide on the
cabinet. Such products may damage or discolor the
cabinet.
34)
WARNING:
RISK OF ELECTRIC SHOCK!
Never spill liquids or push objects of any kind into
the TV cabinet slots.
35) While it is thundering, do not touch the
connecting cables or apparatus.
36) For added protection of your TV from lightning
and power surges, always unplug the power
cord and disconnect the antenna from the TV if
you leave the TV unattended or unused for long
periods of time.
(continued)
4
37) ALWAYS unplug the TV to completely disconnect
from mains power. When the TV is turned off using
the on/off switch, it is not completely disconnected
from power and a minute amount of current is still
consumed.
38) During normal use, the TV may make occasional
snapping or popping sounds. This is normal,
especially when the unit is being turned on or off. If
these sounds become frequent or continuous, unplug
the power cord and contact a Toshiba Authorized
Service Center.
39)
DANGER: RISK OF SERIOUS
PERSONAL INJURY OR DEATH!
Never strike the screen
with a sharp or heavy
object.
40) • The LCD screen of this product can be damaged
by ultraviolet radiation from the sun. When
selecting a location for the television, avoid
locations where the screen may be exposed to
direct sunlight, such as in front of a window.
• Never touch, press, or place anything on the LCD
screen. These actions will damage the LCD screen.
If you need to clean the LCD screen, follow the
instructions in item 33 on page4.
Service
41)
WARNING:
RISK OF ELECTRIC SHOCK!
Never attempt to service the TV yourself. Opening
and removing the covers may expose you to
dangerous voltage or other hazards. Failure to follow
this WARNING may result in death or serious injury.
Refer all servicing not specified in this manual to a
Toshiba Authorized Service Center.
42) If you have the TV serviced:
• Ask the service technician to use only replacement
parts specified by the manufacturer.
• Upon completion of service, ask the service
technician to perform routine safety checks to
determine that the TV is in safe operating condition.
43) The cold cathode fluorescent lamp in the LCD panel
contains a small amount of mercury.
When the TV reaches the end of its useful life,
dispose of the used TV by the approved method for
your area, or ask a qualified service technician to
properly dispose of the TV.
Note: The lamp(s) inside this product
contain mercury. Disposal may be regulated
due to environmental considerations. For
disposal or recycling information, contact
your local authorities or the Electronics
Industries Alliance (www.eiae.org).
Choosing a location for your LCD TV
To Display your LCD TV on the included
Pedestal Stand:
Observe the following safety precautions:
1) Read and Follow the pedestal assembly instructions
included with the pedestal.
CAUTION: Before beginning pedestal assembly,
carefully lay the front of the LCD Panel face down
on a flat, cushioned surface such as a quilt or blanket.
Leave the bottom of the unit protruding over the edge
of the surface and assemble the pedestal as indicated
below.
Note: Extreme care should always be used
when attaching the pedestal stand to avoid
damage to the LCD panel.
2) Place the TV on a sturdy, level surface that can
support the weight of the TV.
3) Be sure to secure the TV to a wall, pillar, surface, or
other immovable structure. ( item 23, page 4).
To Display your LCD TV using a Wall
Bracket:
If you decide to wall mount your LCD TV, always use
a UL listed wall bracket appropriate for the size and
weight of the LCD TV ( page 2):
1) CAUTION: Two people are required for installation.
2) Unplug and remove any cables and/or other
component connectors from the rear of the TV.
3) Remove the screws of the VESA Mounting Pattern
show in the next page.
4) Follow the instructions provided with your
wall bracket. Before proceeding, make sure the
appropriate bracket(s) are attached to the wall and
the back of the TV as described in the instructions
provided with the wall bracket.
5) After attaching the appropriate bracket(s) to the wall
and the back of the TV, remove the pedestal stand
from the TV as described below.
(continued)
5
40” TV
6) VESA Mounting Pattern
TV Size
Hole Pattern(HxV)
VESA Mounting Pattern
Screw Size
32”
200x200 mm
M6
37”
200x200 mm
M6
40”
200x200 mm
M6
46”
400x200 mm
M8
(unit in mm)
Removing the Pedestal Stand
1) Carefully lay the front of the unit face down on a flat,
cushioned surface such as a quilt or blanket. Leave
the stand protruding over the edge of the surface.
Note: Extreme care should always be used
when removing the pedestal stand to avoid
damage to the LCD panel.
2) Remove the four screws shown in the right diagram.
This will allow removal of the pedestal stand.
3) Once you have removed all four screws, holding the
pedestal stand in place, remove the pedestal stand
from the TV.
32” TV
Four screws
Hook
Sturdy strap
(as short as possible)
46” TV
VESA Mounting Pattern
VESA Mounting Pattern
Four screws
Hook
Sturdy strap
(as short as possible)
Hook
Four screws
37” TV
Sturdy strap
(as short as possible)
VESA Mounting Pattern
Four screws
Hook
Sturdy strap
(as short as possible)
6
CAUTION: Always place the TV on the floor or a sturdy,
level, stable surface that can support the weight of
the unit. To secure the TV, use a sturdy strap from
the hook(s) on the rear of the TV to a wall stud, pillar,
or other immovable structure. Make sure the strap is
tight, secure, and parallel to the floor.
FCC Declaration of Conformity
Compliance Statement (Part 15):
The Toshiba 32RV525RZ, 32RV52RZ, 37RV525RZ,
37RV52RZ, 40RV525R, 40RV525RZ, 40RV52R,
40RV52RZ, 46RV525R, and 46RV525RZ Televisions
comply with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
The party responsible for compliance to these rules is:
Toshiba America Consumer Products, L.L.C.
82 Totowa Rd. Wayne, NJ 07470.
Ph: 1-800-631-3811
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by removing
and applying power to the equipment, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
the receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Caution: Changes or modifications to this
equipment not expressly approved by Toshiba
could void the user’s authority to operate this
equipment.
ENERGY STAR® User
Information
ENERGY STAR User Information Statement: the
factory default settings of this television meet ENERGY
STAR requirements. Changing Picture Settings may
increase energy consumption, possibly beyond the limits
required for ENERGY STAR qualification.
To ensure your television is operating at optimal energy
efficiency, select [Home] mode during initial activation.
To return to [Home] mode settings, select [Standard]
picture mode. [Standard] mode is recommended for
normal home use.
ENERGY STAR® qualified TV.
Products that earn the ENERGY
STAR prevent green house
gas emissions by meeting
strict guidelines set by the
U.S. Environmental Protection
Agency. ENERGY STAR and
the ENERGY STAR mark are
registered U.S. marks.
Important notes about your
LCD TV
The following symptoms are technical limitations
of LCD Display technology and are not an
indication of malfunction; therefore, Toshiba is
not responsible for perceived issues resulting from
these symptoms.
1) An afterimage (ghost) may appear on the screen if
a fixed, nonmoving image is displayed for a long
period of time. The afterimage is not permanent
and will disappear in a short period of time.
2) The LCD panel contained in this TV is
manufactured using an extremely high level
of precision technology; however, there may
be an occasional pixel (dot of light) that does
not operate properly (does not light, remains
constantly lit, etc.). This is a structural property of
LCD technology, is not a sign of malfunction, and
is not covered under your warranty. Such pixels
are not visible when the picture is viewed from a
normal viewing distance.
Note: Interactive video games that involve
shooting a “gun” type of joystick at an onscreen target may not work with this TV.
Trademark Information
• QSound and [ ] symbol are trademarks of
QSound Labs, Inc.
• Manufactured under license from Dolby
Laboratories.
Dolby and the double-D symbol are trademarks
of Dolby Laboratories.
• HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
7
Contents
Important Safety Instructions................................ 3
Installation, Care, and Service.............................. 3
Chapter 1: Introduction....................................... 9
Features of your new TV....................................................... 9
Overview of steps for installing, setting up, and using
your new TV................................................................. 10
TV front and side panel controls and connections...............11
TV back panel connections................................................. 12
Chapter 2: Connecting your TV.............................13
Overview of cable types...................................................... 13
About the connection illustrations...................................... 13
Connecting a VCR (or a VCR with S-video) and antenna,
Cable TV or Camcorder............................................... 14
Connecting a DVD player with ColorStream®
(component video), a VCR, and a satellite receiver.... 15
Connecting an HDMI™ or DVI device to the
HDMI input.................................................................. 16
REGZA-LINK® connection................................................ 17
Connecting a digital audio system...................................... 18
Connecting an audio system............................................... 18
Connecting a personal computer (PC)................................ 19
Chapter 3: Using the remote control.......................20
Preparing the remote control for use................................... 20
Installing the remote control batteries................................. 20
Remote control effective range........................................... 20
Learning about the remote control...................................... 21
Using the remote control to control your other devices..... 22
Remote Control functional key chart.................................. 23
Programming the remote control to control
your other devices........................................................ 24
Remote control codes.......................................................... 25
Chapter 4: Menu layout and navigation...................27
Main menu layout................................................................ 27
Setup/Installation menu layout............................................ 28
Navigating the menu system............................................... 28
Chapter 5: Setting up your TV...............................29
Setting the Energy Saving Mode......................................... 29
Selecting the menu language............................................... 29
TOSHIBA Logo LED......................................................... 29
Configuring the antenna input source for the
ANT/CABLE terminal................................................. 29
Programming channels into the TV’s channel memory..... 30
Programming channels automatically............................. 30
Manually adding and deleting channels in
the channel memory.............................................. 30
Labeling channels................................................................ 31
Setting the HDMI™ audio mode........................................ 32
Viewing the digital signal meter......................................... 33
Setting the time zone........................................................... 33
Viewing the system status................................................... 33
Chapter 6: Using the TV’s features.........................34
Selecting the video input source to view............................ 34
Labeling the video input sources........................................ 34
Tuning channels................................................................... 35
Tuning channels using the Channel Browser™.............. 35
Setting the Channel Tuning Mode................................... 37
Tuning to the next programmed channel......................... 38
Tuning to a specific channel (programmed or
unprogrammed)..................................................... 38
Switching between two channels using
Channel Return...................................................... 38
Switching between two channels using SurfLock™...... 38
Selecting the picture size..................................................... 38
8
Scrolling the TheaterWide® picture
(TheaterWide 2 and 3 only)......................................... 40
Using the auto aspect ratio feature...................................... 40
Selecting the cinema mode ................................................ 41
Using the FREEZE feature................................................. 41
Adjusting the picture........................................................... 41
Selecting the picture mode............................................... 41
Adjusting the picture quality........................................... 42
Using the closed caption mode........................................... 42
Base closed captions........................................................ 42
Digital CC Settings ......................................................... 43
CC Selector...................................................................... 43
Adjusting the audio............................................................. 43
Muting the sound............................................................. 43
Using the digital audio selector....................................... 43
Selecting stereo/SAP broadcasts...................................... 44
Adjusting the audio quality.............................................. 44
Selecting the optical audio output format........................ 44
Using the Dolby® Digital Dynamic Range Control
feature.................................................................... 45
Using the Locks menu......................................................... 45
Entering the PIN code...................................................... 45
If you cannot remember your PIN code.......................... 45
Changing your PIN code................................................. 45
Blocking TV programs and movies
by rating (V-Chip)................................................. 45
Downloading an additional rating system for
blocking TV programs and movies....................... 46
Blocking channels............................................................ 47
Unlocking programs temporarily.................................... 48
Using the input lock feature............................................. 48
Using the GameTimer®. .................................................. 48
Using the control panel lock feature................................ 49
Using the PC settings feature.............................................. 49
Setting the PC Audio........................................................... 50
Setting the sleep timer......................................................... 50
Using REGZA-LINK®. .................................................... 50
REGZA-LINK® playback device
(DVD player, etc.) control ................................... 50
REGZA-LINK® input source selection........................... 51
VOLUME and MUTE controls of Audio Receiver........ 51
Other REGZA-LINK® functions..................................... 51
Displaying TV status information....................................... 52
Understanding the auto power off feature.......................... 52
Understanding the last mode memory feature.................... 52
Chapter 7: Using the TV’s advanced features............53
Using the advanced picture settings features...................... 53
Using dynamic contrast................................................... 53
Using the static gamma feature....................................... 53
Using CableClear® digital noise reduction...................... 54
Using MPEG noise reduction.......................................... 54
Using the Game Mode feature......................................... 54
Using the advanced audio settings features........................ 55
Using the QSound® sound feature................................... 55
Chapter 8: Troubleshooting.................................56
General troubleshooting...................................................... 56
Chapter 9: Appendix..........................................58
Specifications...................................................................... 58
Acceptable signal formats for PC IN and
HDMI terminals........................................................... 59
Limited United States Warranty
for LCD Televisions 26” and Larger............................ 60
Limited Canadian Warranty
for Toshiba Brand Flat Panel Televisions.................... 61
Chapter 1: Introduction
Features of your new TV
The following are just a few of the many exciting
features of your new Toshiba widescreen, integrated
HD, LCD TV:
• Integrated digital tuning (8VSB ATSC and
QAM) eliminates the need for a separate digital
converter set-top box (in most cases).
• 1080p output resolution.
• Three HDMI™ digital, high-definition
multimedia interfaces 1080p input support (
page 16).
• HDMI new capability
Lip-Sync Latency activates an audio/video
display timing adjustment function that allows
HDMI source devices to accurately perform
synchronization automatically.
• Two sets of ColorStream® HD high-resolution
component video inputs ( page 15).
• QSound® audio technologies ( page 55).
• Digital Audio Out optical audio connection with
Dolby® Digital optical output format ( page 44).
• CableClear® digital picture noise reduction (
page 54).
• PC IN (Analog RGB) computer terminal ( page
19).
• Channel Labeling allows you to put the Call
Letters (e.g. ABC, HBO, etc.) on the screen along
with the station numbers, so you always know
what you’re watching ( page 31).
• REGZA-LINK allows control of external devices
from the TV remote via HDMI connection(
page 50).
9
Chapter 1: Introduction
Overview of steps for installing,
setting up, and using your new TV
Follow these steps to set up your TV and begin using
its many exciting features.
1
2
Carefully read the important safety, installation,
care, and service information. Keep this manual
for future reference.
Observe the following when choosing a location
for the TV:
•Read “Important notes about your LCD TV”
3
( page 7).
•Place the TV on the floor or a sturdy, level,
stable surface that can support the weight of the
unit. Secure the TV to a wall, pillar, or other
immovable structure ( page 4).
•Place the TV in a location where light does not
reflect on the screen.
•Place the TV far enough from walls and other
objects to allow proper ventilation. Inadequate
ventilation may cause overheating, which will
damage the TV. THIS TYPE OF DAMAGE
IS NOT COVERED UNDER THE TOSHIBA
WARRANTY.
Do not plug in any power cords until AFTER you
have connected all cables and devices to your TV.
4
BEFORE connecting cables or devices to the TV,
learn the functions of the TV’s connections and
controls ( pages 11–12).
5
Connect your other electronic device(s) to the TV
( pages 13–19).
6
Install the batteries in the remote control ( page
20).
7
See “Learning about the remote control” ( page
21) for an overview of the buttons on the remote
control.
8
Program the remote control to operate your other
device(s) ( pages 22–26).
9
AFTER connecting all cables and devices, plug
in the power cords for your TV and other devices.
Then press POWER on the TV control panel or
remote control to turn on the TV. If the TV stops
responding to the controls on the remote control
or TV control panel and you cannot turn the TV
off or on, please unplug the power cords few
seconds then re-plug to try again.
10
10 See “Menu layout and navigation” for a quick
overview of navigating the TV’s menu system
( page 27).
11 Program channels into the TV’s channel memory
( page 30).
12 For details on using the TV’s features, see
Chapters 6 and 7.
13 For help, refer to the Troubleshooting Guide,
Chapter 8.
14 For technical specifications and warranty
information, see Chapter 9.
15 Enjoy your new TV!
Chapter 1: Introduction
TV front and side panel controls and connections
Model 40RV525RZ is used in this manual for illustration purposes.
Left side panel
TV front
TV top
Control panel
1無 Green LED and TOSHIBA Logo LED
Power LED(Green) = Power indicator
TOSHIBA Logo LED= On or Off ( page 29).
6無 ARROWS pqtu — When a menu is onscreen, these buttons function as up/down/left/
right menu navigation buttons.
2無 Remote sensor — Point the remote control
toward this remote sensor ( “Remote control
effective range” on page 20).
7無 MENU (ENTER) — Press to access the menu
system ( pages 27–28). When a menu is onscreen, the MENU button on the TV’s control
panel functions as the ENTER button.
3無 VIDEO-2 IN — The side panel A/V connections
are referred to as “VIDEO 2” and include standard
A/V connections.
4無 Service port — For service use only. Used for
updating the television’s firmware.
5無 POWER — Press to turn the TV on and off.
If the TV stops responding to the controls on
the remote control or TV control panel and
you cannot turn off the TV, press and hold the
POWER button on the TV control panel for 5 or
more seconds to reset the TV.
8無 EXIT — Press to instantly close an on-screen
menu.
9無 CHANNEL pq — When no menu is on-screen,
these buttons change the channel (programmed
channels only;  page 30).
10無 VOLUME tu — These buttons adjust the
volume level.
11無 INPUT — Repeatedly press to change the source
you are viewing (ANT/CABLE, VIDEO 1, VIDEO 2,
ColorStream HD1, ColorStream HD2, HDMI 1,
HDMI 2, HDMI 3, PC).
11
Chapter 1: Introduction
TV back panel connections
For an explanation of cable types and connections, see pages 14–20.
TV back
Power Cord
1無 HDMI™ IN — High-Definition Multimedia
Interface input receives digital audio and
uncompressed digital video from an HDMI
device or uncompressed digital video from a DVI
device. HDMI connection is necessary to receive
1080p signals.
4無 Audio OUT Variable — Analog audio outputs for
connecting an audio amplifier.
2無 ColorStream® HD-1 and ColorStream® HD-2
— Two sets of ColorStream® high-definition
component video inputs (with standard stereo
audio inputs) for connecting devices with
component video output, such as a Toshiba DVD
player with ColorStream®.
6無 Digital Audio OUT — Optical audio output in
Dolby Digital or PCM (pulse-code modulation)
format for connecting an external Dolby Digital
decoder, amplifier, A/V receiver, or home theater
system with optical audio input.
Note: Component video cables carry only
video information; separate audio cables
are required for a complete connection.
3無 VIDEO-1 IN — Standard (composite) video and
standard audio inputs plus optional S-video
inputs for connecting devices with composite
video or S-video output.
Note: Standard (composite) video and
S-video cables carry only video information;
separate audio cables are required for a
complete connection.
12
5無 ANT/CABLE — Antenna input that supports
analog (NTSC) and digital (ATSC) off-air
antenna signals and analog and digital Cable TV
(QAM) signals.
7無 PC/HDMI-1 (AUDIO) IN — PC audio input
terminals are shared with HDMI-1 analog audio
input terminals, and their use can be configured
in the Audio Setup menu ( page 50).
8無 PC IN — For use when connecting a personal
computer.
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.Manufactured
under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of
Dolby Laboratories.
Chapter 2: Connecting your TV
Overview of cable types
Cables can be purchased from most stores that sell audio/
video devices. Before purchasing any cables, be sure of
connector types required by your devices and the length
of each cable.
Coaxial (F-type) cable
Coaxial (F-type) cable is used for connecting your
antenna, cable TV service, and/or cable converter box
to the ANT/CABLE input on your TV.
Standard A/V cables (red/white/yellow)
HDMI™ cable
(with HDMI Logo “
”)
HDMI (High-Definition Multimedia Interface) cable
is for use with devices with an HDMI output. An
HDMI cable delivers digital audio and video in its
native format. This cable carries both video and audio
information; therefore, separate audio cables are not
required for a complete HDMI device connection (
page 16 and page 19).
Note: HDMI cable provides better picture
performance than a standard (composite) video or
S-video cable.
Optical audio cable
Standard A/V cables (composite video) usually come
in sets of three, and are for use with video devices with
analog audio and composite video output. These cables
(and the related inputs on your TV) are typically colorcoded according to use: yellow for video, red for stereo
right audio, and white for stereo left (or mono) audio.
S-video cable
Optical audio cable is for connecting receivers with
Dolby Digital or PCM (pulse-code modulation) optical
audio input to the TV’s DIGITAL AUDIO OUT terminal
( page 18).
Analog RGB (15-pin) computer cable
S-video cable is for use with video devices with
S-video output. Separate audio cables are required for a
complete connection.
Analog RGB (15-pin) computer cable is for connecting
a PC to the TV’s PC IN terminal ( page 19).
Note: An S-video cable provides better picture
performance than a composite video cable. If you
connect an S-video cable, be sure to disconnect
the standard (composite) video cable or the picture
performance will be unacceptable.
About the connection illustrations
Component video cables (red/green/blue)
You can connect different types and brands of devices to
your TV in several different configurations. The connection
illustrations in this manual are representative of typical
device connections only. The input/output terminals on
your devices may differ from those illustrated herein. For
details on connecting and using your specific devices, refer
to each device’s owner’s manual.
Component video cables come in sets of three and are
for use with video devices with component video output.
(ColorStream® is Toshiba’s brand of component video.)
These cables are typically color-coded red, green, and
blue. Separate audio cables are required for a complete
connection.
Note: Component video cables provide better
picture performance than a standard (composite)
video or S-video cable.
13
Chapter 2: Connecting your TV
Connecting a VCR (or a VCR with S-video) and antenna, Cable TV or
Camcorder
From Cable TV or
antenna
Camcorder
From Cable TV
Cable box
TV back panel
AUDIO
OUT
IN CH 3
CH 4
VIDEO
OUT
L
R
S-video cable
VIDEO 2 inputs
on TV right side
panel
Stereo VCR
or
Standard
A/V cable
VIDEO
L
AUDIO
R
IN
OUT
L
R
CH 3
CH 4
IN
from
ANT
OUT
to
TV
Audio cable
You will need:
• coaxial cables
• S-video cable
−− For better picture performance, if your VCR
has S-video, use an S-video cable (plus the
audio cables) instead of the standard video
cable. Do not connect both types of video
cable to VIDEO 1 at the same time or the
picture performance will be unacceptable.
−− For better picture performance, if your
camcorder has S-video, connect an S-video
cable (plus the audio cables) to VIDEO 1 on
the TV back side instead of the VIDEO 2 on
the TV side panel.
−− If you have a mono VCR, connect L/MONO
on the TV to your VCR’s audio out terminal
using the white audio cable only.
• S-video cable (if your VCR or camcorder has S-video)
−− Do not connect both types of video cable
to VIDEO 1 at the same time or the picture
performance will be unacceptable.
• standard audio cables (If you have a mono VCR or
camcorder has S-video)
Note: When you use a Cable box, you may not
be able to use the remote control to program or
access certain features on the TV.
14
To view the antenna or Cable signal:
Select the ANT/CABLE video input source on the TV.*
To view basic and premium Cable channels:
Turn OFF the VCR. Select the ANT/CABLE video
input source on the TV.* Tune the TV to channel 3 or
4 (whichever channel the Cable box output is set to).
Use the Cable box controls to change channels.
To view the VCR:
Turn ON the VCR. Select the VIDEO 1 video input
source on the TV.*
To view the camcorder video:
Select the VIDEO 2 video input source on the TV.*
** To select the video input source, press INPUT on
the remote control ( page 21). To program the
TV remote control to operate other devices, see
Chapter 3.
The unauthorized recording, use, distribution, or
revision of television programs, videotapes, DVDs,
and other materials is prohibited under the Copyright
Laws of the United States and other countries, and may
subject you to civil and criminal liability.
Chapter 2: Connecting your TV
Connecting a DVD player with ColorStream® (component video), a VCR,
and a satellite receiver
Your TV has two sets of ColorStream® (component video) inputs.
From antenna
TV back panel
Y
PB
PR
COMPONENT VIDEO S-VIDEO VIDEO
OUT
OUT
AUDIO
OUT
L
Stereo VCR
VIDEO
L
AUDIO
R
IN
R
CH 3
CH 4
OUT
DVD player with component video
L
IN from ANT
OUT to TV
R
From satellite dish
Y
Satellite
IN
PB
PR
COMPONENT VIDEO S-VIDEO VIDEO
OUT
OUT
AUDIO
OUT
L
R
Satellite receiver with component video
You will need:
• coaxial cables
• standard A/V cables
−− For better picture performance, if your VCR
has S-video, use an S-video cable (plus the
audio cables) instead of the standard video
cable. Do not connect both types of video
cable to VIDEO 1 at the same time or the
picture performance will be unacceptable.
−− If you have a mono VCR, connect L/MONO
on the TV to your VCR’s audio out terminal
using the white audio cable only.
• standard audio cables
• component video cables
−− You can connect the component video cables
(plus audio cables) from the DVD player or
satellite receiver to either set of ColorStream
terminals on the TV (HD-1 or HD-2). The
ColorStream HD-1 and HD-2 terminals
can be used with Progressive (480p, 720p)
and Interlaced (480i, 1080i) scan systems.
A 1080i signal will provide the best picture
performance (1080p is not supported).
−− If your DVD player or satellite receiver does
not have component video, connect a
standard A/V cable to VIDEO 2 on the side
panel. If your DVD player has HDMI video,
see page 16.
To view antenna or Cable channels:
Select the ANT/CABLE video input source on the TV.*
To view the DVD player:
Turn ON the DVD player. Select the ColorStream
HD-1 video input source on the TV.*
To view satellite programs using the
component video connections:
Turn on the satellite receiver. Select the ColorStream
HD-2 video input source on the TV.*
To view the VCR or view and record
antenna channels:
Turn ON the VCR. Tune the VCR to the channel you want
to watch. Select the VIDEO 1 video input source on the TV.*
To record a TV program while watching a DVD:
Turn ON the VCR. Tune the VCR to the channel to
record. Select the ColorStream HD-1 video input source
on the TV* to view the DVD.
** To select the video input source, press INPUT on
the remote control ( page 21). To program the
TV remote control to operate other devices, see
Chapter 3.
The unauthorized recording, use, distribution, or
revision of television programs, videotapes, DVDs,
and other materials is prohibited under the Copyright
Laws of the United States and other countries, and may
subject you to civil and criminal liability.
15
Chapter 2: Connecting your TV
Connecting an HDMI™ or DVI
device to the HDMI input
The HDMI input on your TV receives digital audio
and uncompressed digital video from an HDMI
source device, or uncompressed digital video from a
DVI (Digital Visual Interface) source device.
This input is designed to accept HDCP (HighBandwidth Digital-Content Protection) program
material in digital form from EIA/CEA-861-D–
compliant[1] consumer electronic devices (such as
a set-top box or DVD player with HDMI or DVI
output).
The HDMI input can accept and display VGA,
SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p
(60Hz), 720p (60Hz), 1080i (60Hz) and 1080p
(24Hz/60Hz) signal formats. For detailed signal
specifications, see page 59.
Supported Audio format: Linear PCM, sampling rate
32/44.1/ 48 kHz
Note: To connect a PC to the HDMI input, see page 19.
To connect a DVI device, you will need:
• one HDMI-to-DVI adapter cable (HDMI type A
connector) per DVI device
−− For proper operation, the length of an HDMIto-DVI adapter cable should not exceed 9.8 ft
(3m). The recommended length is 6.6 ft (2m).
• one pair of standard analog audio cables per DVI
device
−− An HDMI-to-DVI adapter cable transfers
video only. Separate analog audio cables
are required (see illustration).
−− See “Setting the HDMI™ audio mode”
( page 32).
TV back panel
To connect an HDMI device, you will need:
• one HDMI cable (type A connector) per HDMI device
−− For proper operation, it is recommended that
you use an HDMI cable with the HDMI Logo (
).
−− To display an 1080i/60Hz signal format, you
will need a Category 2 cable. Conventional
HDMI/DVI cable may not work properly.
−− HDMI cable transfers both video and audio.
Separate analog audio cables are not
required (see illustration).
−− See “Setting the HDMI™ audio mode”
( page 34).
TV back panel
HDMI device
To view the HDMI device video:
Select the HDMI 1, HDMI 2 or HDMI 3 video input
source on the TV.*
** To select the video input source, press INPUT on
the remote control ( page 21). To program the
TV remote control to operate other devices, see
Chapter 3.
16
DVI device
VIDEO
L
DVI/HDCP
OUT
AUDIO
R
IN IN
OUT
L
R
Note: To ensure that the HDMI or DVI device is reset
properly, it is recommended that you follow these
procedures:
•• When turning on your electronic components,
turn on the TV first, and then the HDMI or
DVI device.
•• When turning off your electronic components,
turn off the HDMI or DVI device first, and
then the TV.
[1]EIA/CEA-861-D compliance covers the
transmission of uncompressed digital video
with high-bandwidth digital content protection,
which is being standardized for reception of
high-definition video signals. Because this is
an evolving technology, it is possible that some
devices may not operate properly with the TV.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
Chapter 2: Connecting your TV
®
REGZA-LINK connection
You can control the basic functions of connected audio/video devices using the TV’s remote control if you
connect a REGZA-LINK compatible audio receiver or playback device. For an explanation of setup and
operations, see pages 51.
TV back panel
Playback device
Audio receiver
(REGZA-LINK DVD player,etc.)
Playback device
(REGZA-LINK HD DVD player,etc.)
To connect an Audio Receiver and Playback
Devices, you will need:
Before controlling the device(s):
• HDMI cables ( page 16)
REGZA-LINK Setup menu as you desire ( page
51).
• The connected devices must also be set. For
details, see the operation manual for each device.
• The REGZA-LINK feature uses the CEC
technology as regulated by the HDMI standard.
• This feature is limited to models incorporating
Toshiba’s REGZA-LINK. However, Toshiba is not
liable for those operations. Refer to the individual
instruction manuals for compatibility information.
Note:
• If several devices are connected, REGZA-LINK
feature may not operate properly.
• For proper operation, it is recommended that you
use HDMI cables with the HDMI Logo
(
).
• After completing the above connections, set the
Note: This feature may not work properly
depending on the devices that are connected.
17
Chapter 2: Connecting your TV
The TV’s DIGITAL AUDIO OUT terminal outputs a
Dolby®* Digital
or 2-channel down-mixed
PCM (pulse-code modulation) signal for use with
an external Dolby® Digital decoder or other external
audio system with optical audio input.
standard optical out signals may not work
properly, creating a high noise level that
may damage speakers or headphones.
THIS DAMAGE IS NOT COVERED BY YOUR
WARRANTY.
•• The DIGITAL AUDIO OUT terminal may not
output some digital audio sources because
of copy restrictions.
You will need:
• optical audio cable (Use an optical audio cable
** Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol are
trademarks of Dolby Laboratories.
Connecting a digital audio system
that has the larger “TosLink” connector and not
the smaller “mini-optical” connector.)
Dolby Digital decoder or
other digital audio system
Connecting an audio system
This connection allows you to use external speakers with
an external analog audio amplifier to adjust the sound level.
You will need:
• standard audio cables
TV back panel
Analog audio amplifier
LINE IN
L
R
TV back panel
To control the audio:
1無 Turn on the TV and the digital audio device.
2無 Press on the TV’s remote control and open the
Audio menu.
3無 Highlight Audio Setup and press
.
To control the audio:
1無 Turn on the TV and the stereo amplifier.
2無 Set up a optimum volume level of the stereo amplifier.
Audio
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio Setup
4無 In the Optical Output Format field, select either Dolby
Digital or PCM, depending on your device (“Selecting
the optical audio output format” on page 44).
Audio Setup
PC Audio
No
HDMI 1 Audio
Auto
MTS
Stereo
Language
English
Optical Output Format
Dolby Digital
Dolby Digital
Dynamic Range Control
Compressed
Reset
Done
Note:
•• Some audio systems may not be compatible
with Dolby Digital bitstream signals. Older
audio systems that are not compatible with
18
Then you can adjust the sound volume level from the
TV’s volume control or the amplifier’s volume control.
3無 Menu item of Speakers can turn to OFF to mute the
TV’s built in speakers.
Chapter 2: Connecting your TV
Connecting a personal computer (PC)
With either the PC IN or HDMI connection, you can watch
your computer’s display on the TV and hear the sound
from the TV’s speakers.
• Signal names for mini D-sub 15-pin connector
Pin
No.
Signal
name
Pin
No.
Signal
name
Pin
No.
Signal
name
1
R
6
Ground
11
Reserved
2
G
7
Ground
12
SDA
To connect a PC to the PC IN terminal on the TV:
3
B
8
Ground
13
H-sync
When connecting a PC to the PC IN terminal on the TV, use
an analog RGB (15-pin) computer cable and a PC audio cable.
4
Reserved 9
5V
14
V-sync
5
Reserved 10
Ground
15
SCL
TV back panel
To connect a PC to the HDMI terminal on the TV:
PC audio
cable
When connecting a PC to the HDMI terminal on the
TV, use an HDMI-to DVI adapter cable and analog
audio cables.
If connecting a PC with an HDMI terminal, use an
HDMI cable (type A connector). Separate analog
cables are not necessary ( page 15).
TV back panel
Computer
PC audio
output
Conversion adapter
(if necessary)
• To use a PC, set the monitor output resolution on the
PC before connecting it to the TV. The PC IN terminal
can accept and display VGA, SVGA, XGA, WXGA and
SXGA signal formats. For detailed signal specifications
( page 59).
Other formats or non-standard signals will not be
displayed correctly.
• To display the optimum picture, use the PC setting
feature ( “Using the PC settings feature” on page 49).
Note:
•• The PC audio input terminals on the TV are shared
with the HDMI-1 analog audio input terminals (
page 50).
•• Some PC models cannot be connected to this TV.
•• An adapter is not needed for computers with a
compatible mini D-sub15-pin terminal.
•• Depending on the DVD’s title and the
specifications of the PC on which you are playing
the DVD-Video, some scenes may be skipped or
you may not be able to pause during multi-angle
scenes.
PC audio
cable
Computer
PC audio
output
The HDMI input can accept and display VGA, SVGA,
XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p
(60Hz), 1080i (60Hz), and 1080p (24Hz/60Hz) signal
formats. For detailed signal specifications, see page 59.
Note:
•• The edges of the images may be hidden.
•• If receiving a 480i (HDMI), 480p (HDMI), 720p,
1080i, or 1080p signal program, Native mode
scales the video to display the entire picture within
the borders of the screen (i.e. no overscanning).
19
Chapter 3: Using the remote control
Preparing the remote control for
use
Your TV remote control can operate your TV and
many other devices such as cable converter boxes,
satellite receivers, VCRs, DVD players, and HTIBs
(home theater in a box), even if they are different
brands.
If you have a Toshiba device:
Your TV remote control is preprogrammed to operate
most Toshiba devices ( page 24).
If you have a non-Toshiba device or a
Toshiba device that the remote control is not
preprogrammed to operate:
You can program the TV remote control so it will
operate the other device ( pages 22–26).
Installing the remote control
batteries
1無Remove the battery cover from the back of the
•• If the remote control does not operate
correctly, or if the operating range becomes
reduced, replace batteries with new ones.
•• When necessary to replace batteries in the
remote control, always replace both batteries
with new ones. Never mix battery types or use
new and used batteries in combination.
•• Always remove batteries from the remote
control if they are dead or if the remote
control is not to be used for an extended
period of time. This will prevent battery acid
from leaking into the battery compartment.
Remote control effective range
For optimum performance, aim the remote control
directly at the TV and make sure there is no
obstruction between the remote control and the TV.
Point remote control
toward remote sensor
on front of TV.
remote control.
Squeeze tab
and lift cover.
2無Install two “AAA” size batteries, making sure to
match the + and – signs on the batteries to the
signs on the battery compartment.
3無Reinsert the battery cover in the remote control
until the tab snaps.
Caution: Batteries must not be exposed to
excessive heat such as sunshine, fire or the
like.
Note:
•• Be sure to use AAA size batteries.
•• Dispose of batteries in a designated disposal
area.
•• Batteries should always be disposed of with
the environment in mind. Always dispose of
batteries in accordance with applicable laws
and regulations.
20
16.4 ft (5m)
Chapter 3: Using the remote control
Learning about the remote control
The buttons used for operating the TV only are
described here. For a complete list of the remote
control’s functions, see the remote control functional
key chart ( page 23).
1無 POWER turns the TV on and off. When the TV is
on, the green LED indicator on the TV front will be
illuminated.
2無 FREEZE freezes the picture. Press again to restore the
moving picture ( page 41).
3無 SLEEP accesses the sleep timer ( page 50).
4無 PIC SIZE cycles through the picture sizes: Natural,
TheaterWide 1/2/3, Full, 4:3 HD, Native and Dot by Dot
( page 39-40).
5無 Channel Numbers (0–9, –/100) directly tune channels.
The
button is used to tune digital channels ( page
38) or to edit the Favorites List ( page 36).
6無 INPUT selects the video input source ( page 34).
7無 CH pq cycles through programmed channels when no
menu is on-screen ( page 30).
8無 VOL + – adjusts the volume level.
9無 FAV BROWSER accesses the Favorites List in the Channel
Brower™ ( page 35).
10無RECALL displays TV status information ( page 52).
11無CH RTN returns to the last viewed channel or source
( page 38).
12無MUTE reduces or turns off the sound ( page 43).
13無INFO displays TV status information as well as program
details, when available ( page 52).
/
While watching TV, these buttons open
14無
the Channel Browser™ and tune to the previous/next
channel in the channel history ( page 36). (Also see
“Arrow buttons.”)
15無Arrow buttons (pqtu) When a menu is on-screen,
these buttons select or adjust programming menus. (Also
see
/
.)
16無ENTER activates highlighted items in the main menu
system.
17無MENU accesses the main TV menu system ( pages 27
and 28).
18無EXIT closes on-screen menus.
Note: The error message “NOT AVAILABLE”
may appear if you press a key for a function that
is not available.
19無MODE SELECT switch switches between TV, CABLE/
SAT, AUX 1, and AUX 2 modes ( page 22). Set to “TV”
to control the TV.
21
Chapter 3: Using the remote control
Using the remote control to
control your other devices
1無 POWER Turns the selected device on and off.
If you have a non-Toshiba device or a Toshiba device that
the remote control is not preprogrammed to operate, you
must first program the remote control to recognize the
device (if you have not already done so) ( pages 24–26).
3無 +10 Press to directly access DVD chapters higher than
10.
To use your TV remote control to operate a:
• Cable converter box or satellite receiver, set the
MODE SELECT switch to CABLE/SAT.
• VCR, set the MODE SELECT switch to AUX 1.
• DVD player or HTIB, set the MODE SELECT
switch to AUX 2.
Note: Even after the TV remote control is
programmed, it may not operate certain
features on any other devices. If this happens
and you wish to use those features, you will
need to use the device’s original remote control.
Point the remote control
directly at the device.
2無 Channel Numbers (0-9) Press to directly access
channels (as opposed to
).
4無 TOP MENU Accesses a DVD’s top menu.
5無 CH pq For channels programmed into the channel
memory ( page 30):
p selects the next higher channel.
q selects the next lower channel.
6無 GUIDE Displays the channel guide in the CABLE/SAT
mode.
SET UP Accesses a DVD’s setup menu in the AUX
mode.
7無 INFO Displays TV status information on-screen.
8無 pqtu Press to navigate DVD menus (may not work
on some DVD players).
9無 ENTER Required by some satellite receivers and DVD
players to activate certain functions.
10無DVD CLEAR Press to reset the title and chapter number.
11無PLAY Begins playback of a tape or DVD.
12無PAUSE Press during play or record mode to pause the
picture; press again to restart.
13無STOP Stops the tape or DVD.
14無SKIP
Skips forward to locate later DVD chapters.
15無FF Fast-forwards the tape or DVD. (Press during play
mode to view the picture moving rapidly forward.)
Skips back to beginning of current DVD
16無SKIP
chapter, or locates previous chapters.
17無REW Rewinds/reverses the tape or DVD. (Press
during play mode to view the picture moving rapidly
backward.)
16
17
18
19
18無TV/VCR To view one program while recording another,
press to select TV mode.
SEARCH selects a specific DVD chapter, title or time.
19無REC Starts tape recording.
20無MODE SELECT switch Set to “TV” to control the TV;
“CABLE/SAT” to control a cable converter box or
satellite receiver; “AUX 1” to control a VCR; “AUX 2”
to control a DVD player or HTIB.
22
Chapter 3: Using the remote control
Remote Control functional key chart
Note:
•• “---” = key does not send a signal in that remote control mode.
•• “ TV” = key will affect the TV, even though the remote control is in another mode.
•• * Not available for your TV.
REMOTE CONTROL
KEY
POWER
SLEEP
PIC SIZE
FREEZE
1-9
0
100/–/+10
INPUT
FAV BROWSER/
TOP MENU
MUTE
SET UP/GUIDE
VOL + –
Power
TV
TV
TV
Digit 1-9
Digit 0
– (sub CH)
TV
AUX 1
(VCR)
Power
TV
TV
TV
Digit 1-9
Digit 0
100
TV
AUX 2 (DVD or
HTIB)
Power
TV
TV
TV
Digit 1-9
Digit 0
+10
TV
---
---
Top Menu
Toshiba TV
CABLE
SAT (satellite)
Power
TV
TV
TV
Digit 1-9
Digit 0
--TV
---
INFO
ENTER
Power
Sleep timer
Picture size
FREEZE
Digit 1-9
Digit 0
– (sub CH)
TV/Video select
FAV BROWSER
DVD TOP Menu*
Sound mute
Guide*
Volume up/down
Channel
up/down
RECALL
Previous channel
DVD previous menu*
Info
Enter
pq
Menu up/down
---
CHpq
RECALL
CH RTN/DVD RTN
t
u
MENU
EXIT/DVD CLEAR
PAUSE/STEP
PLAY
STOP
SKIP
SKIP
REW
FF
TV/VCR/
SEARCH
Menu left/
Channel Browser™
Menu right/
Channel Browser™
Menu
Exit
DVD clear*
Pause*
Play*
Stop*
Skip REV*
Skip FWD*
Rewind*
Fast FWD*
DVD search*
TV
TV
Channel
up/down
TV
TV
SAT Guide
TV
Channel
up/down
TV
---
---
---
DVD Return
-----
Info
Select, Enter
Menu
up/down
-----
Display
Enter
---
Menu up/down
---
Menu left
---
Menu left
---
Menu right
---
Menu right
---
Action Menu
---
DVD Menu
---
Exit
---
DVD Clear
---------------
---------------
Pause
Play
Stop
----Rewind
Fast FWD
Pause
Play
Stop
Skip REV
Skip FWD
Rewind
Fast FWD
---
---
TV/VCR
DVD search
---
TV
--TV
Channel
up/down
TV
TV
Setup
TV
--TV
23
Chapter 3: Using the remote control
REMOTE CONTROL
KEY
Toshiba TV
CABLE
SAT (satellite)
REC
REC MENU*
---
---
SLOW –
SLOW +
ANGLE
SUB TITLE
AUDIO
EJECT
SLOW REW*
SLOW FWD*
Angle*
Sub title*
Audio*
Eject*
-------------
-------------
Programming the remote control
to control your other devices
Your Toshiba TV remote control is preprogrammed
to operate most Toshiba devices. To program your
TV remote control to operate a non-Toshiba device
(or a Toshiba device that it is not preprogrammed to
operate), follow the steps below. For details on using
the remote control to operate the device, see page 22.
1無 In the remote control code table ( page 25), find the
code for your device. If more than one code is listed,
try each one separately until you find one that works.
2無 Set the MODE SELECT switch to the type of device you are
programming the remote control to operate — CABLE/
SAT (for a cable converter box or satellite receiver), AUX
1 (for a VCR or TV/VCR combo), or AUX 2 (for a DVD
player or HTIB [home theater in a box]).
, press the Channel Number
3無 While holding down
buttons to enter the 3-digit code for your device.
4無 To test the code, turn on the device, point the remote
control at it, and press
. See notes below.
• If the correct code was entered, the device will
turn off.
• If the device does not respond, repeat steps 1–4
using another code.
• If the device does not respond to another code,
you will need to use the remote control that came
with the device.
5無 Remember to set the MODE SELECT switch back to
“TV” to control the TV.
6無 For future reference, write down the code(s) you used:
DEVICE
24
CODE
DEVICE
CODE
AUX 1
(VCR)
Record (2
click)
-------------
AUX 2 (DVD or
HTIB)
------DVD Angle
DVD Sub title
DVD Audio
DVD Eject
Note:
•• In addition to POWER, confirm that all necessary
keys on the TV remote control operate your device.
If some keys are not operational, repeat the device
code setup using another code (if other codes
are listed for your device). If, after trying all listed
codes, the necessary keys do not operate your
device, use the device’s original remote control.
•• Every time you change the batteries, you will need
to reprogram the remote control.
•• Some newer VCRs respond to either of two codes.
These VCRs have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch and does not
respond to the codes for your VCR brand, set the
switch to the other position (“VCR1” or “VCR2”)
and reprogram the remote control.
Chapter 3: Using the remote control
Remote control codes
Wards
In some cases you may not be
able to operate your device with
the TV remote control. Your other
device may use a code that is not
recognized by the TV remote
control. If this happens, use the
device’s remote control.
Alphastar
Chaparral
DISH Network
Drake
Cable converter box
ABC
061, 062, 063, 082,
084, 087, 092,
096, 098
Archer
065, 092, 097, 099
Cableview
064, 094
Century
092
Citizen
090, 092, 097
Contec
083, 085, 086, 088,
093, 098
Diamond
093
GE
061, 062
Gemini
069, 070, 094
Hamlin
093
Hitachi
062, 095, 096
Jasco
097
Motorola/GI/
062, 069, 071, 082,
Jerrold
086, 089, 096, 107
Magnavox
072, 096
Memorex
092, 104
Multi Canal
090
Novavision
101
Panasonic
081, 083, 085
Philco
087
Philips
066, 067, 068, 070,
072, 073, 074, 075,
092
Pioneer
076, 077
Proscan
061, 062
Radio Shack
092, 097, 099
RCA
064, 081
Realistic
065
Recoton
102
Samsung
077, 090
Scientific Atlanta 063, 078, 079, 080,
088, 098, 101, 105
Sears
095
Signature
062
Signature 2000 096
Sprucer
081, 085
Starcom
069, 082, 087, 096,
103, 104
Stargate
069, 090
Sylvania
095, 100
TeleView
090
Texscan
100
Tocom
071, 084, 085
U. S. Electronics 087, 096, 098
United Cable
082
Universal
065, 092, 097, 099,
102, 103
096
Satellite receiver
Echostar
Express Vu
Fujitsu
GE
General
Instruments
Hitachi
Hughes
Hughes Network
Systems
Intersat
Janeil
JVC
Kenwood
Magnavox
Optimus
Pansat
Primestar
Proscan
Radio Shack
RCA
Realistic
Samsung
Sony
Star Choice
Star Trak
STS
Toshiba
Uniden
Zenith
038, 059
034
057
020, 040, 044, 046,
050, 053
018, 041, 051
057
027
008, 009, 013
010, 011, 012, 022,
023, 031, 049
033
033
019
048
027
017, 057
029
060
058
036, 052
015, 042
008, 009, 013
022, 023, 030
008, 009, 013, 016
030
059
014, 055
057, 106
025, 026, 037, 054
024
000, 001, 002, 003,
004, 005, 006, 007,
020, 031, 056
021, 028, 030, 032,
035, 039, 043, 045,
047, 058
027
TV/VCR Combo
Action
GE
Goldstar
Panasonic
Precision
Quasar
Realistic
Sony
Toshiba
Zenith
Totevision
078
059, 062
065
065
078
065
079
074
057
065
009, 010, 065
DVD/VCR Combo
Go Video
JVC
DVD=087,
VCR=081
DVD=088,
VCR=082
RCA
Samsung
Sanyo
Zenith
DVD=089,
VCR=083
DVD=090,
VCR=084
DVD=091,
VCR=085
DVD=092,
VCR=086
DVD player
Aiwa
Apex
BOSE
Broksonic
Clarion
Classic
Daewoo
Denon
Emerson
Fisher
Funai
GE
Go Video
GPX
Hitachi
JVC
Kenwood
Konka
Magnavox
Memorex
Mintek
NAD
Nakamichi
Norcent
Onkyo
Oritron
Panasonic
Philips
Pioneer
Proscan
Qwestar
RCA
Sampo
Samsung
Sansui
Sanyo
Sharp
Sherwood
Sony
Sylvania
Teac
Technics
Techwood
Toshiba
Yamaha
Zenith
006, 015
016, 017
097
018
019
020
021
022, 023, 024, 025
026, 027
028
027
001, 029, 030
087
031
005, 032, 033, 034,
035
003, 007, 036, 042,
088
037
008, 009
004, 038
039
040
026
041
043
044
058
010, 045, 046, 047,
048, 049, 050
004, 051
052, 053, 054, 055
001, 056
057, 058
001, 002, 059, 089
060
061, 062, 086, 090
073
063, 091
064, 067
074
011, 012, 065, 066,
068, 069, 070
027
071
072
075
000, 013, 076, 077,
078
079, 080, 081
014, 082, 092
Portable DVD player
Aiwa
093
(continued)
25
Chapter 3: Using the remote control
Audiovox
Panasonic
RCA
094, 095
024, 096, 099
098
VCR
Admiral
Aiko
Aiwa
Akai
049
019
018
003, 004, 037, 038, 039,
058, 069
Audiovox
010
Bell & Howell 007, 068
Broksonic
008, 017
Calix
010
Carver
026
CCE
019
Citizen
009, 010, 011, 012,
013, 014, 015, 019,
057, 073
Colortyme
005
Craig
009, 010, 016, 061,
065, 079
Curtis Mathes 001, 005, 009, 012,
014, 040, 048, 053,
056, 057
Daewoo
011, 013, 015, 017,
018, 019, 057, 078
Daytron
078
Denon
063
Dimensia
001, 048
Electrohome
010, 020, 065
Emerson
003, 008, 010, 011,
017, 018, 020, 028,
039, 054, 057, 062,
065, 068, 072
Fisher
007, 016, 021, 022,
023, 057, 064, 068,
070, 071, 079
Fuji
004, 041
Funai
018, 073
Garrard
018
GE
001, 002, 009, 040,
042, 048, 056
Go Video
056, 059, 061, 081
Goldstar
005, 010, 014, 054,
056, 065, 067
Gradiente
018, 065
Harman Kardon 005
Hitachi
024, 025, 035, 037,
042, 063, 070, 080
JBL
076
JC Penney
005, 006, 007, 008,
009, 010, 023, 024,
025, 026, 035, 056,
061, 063, 065
Jensen
024, 025, 037, 050
JVC
005, 006, 007, 014,
037, 043, 055, 062,
063, 068, 082
Kenwood
005, 006, 007, 012,
014, 037, 043, 050,
053, 068, 071
Kodak
010
LG
010
26
Lloyds
Logik
LXI
Magnasonic
Magnavox
Marantz
Memorex
MGA
MGN
Minolta
Mitsubishi
Montgomery
Ward
Motorola
MTC
Multitech
NEC
053, 073, 079
061
010
061, 065, 078
026, 027, 034, 044,
057, 061, 072
005, 006, 007, 012,
014, 026, 053, 067
007, 009, 010, 016,
018, 034, 049, 063,
065, 066, 068, 075,
079
020, 028, 039
056
024, 025, 035, 063
020, 024, 025, 028,
039, 043, 065
049
049
009, 046, 061
009, 012, 018
005, 006, 007, 012,
014, 037, 043, 053,
054, 067, 070
Nikko
010
Noblex
009
Optimus
010, 049, 065
Optonica
031
Orion
054, 057, 062, 065,
068, 072
Panasonic
036, 045, 046, 057,
061, 072, 079
Pentax
012, 024, 025, 035,
042, 053, 063
Pentex Research 014
Philco
026, 027, 063
Philips
026, 031, 044, 057
Pioneer
006, 024, 043, 055
Portland
012, 013, 015
Proscan
001, 002, 048
Proton
061
Quasar
045
Radio Shack
010, 031, 065
Radio Shack/
007, 009, 010, 016,
Realistic
018, 020, 021, 022,
031, 049
Radix
010
RCA
001, 002, 003, 009,
024, 025, 029, 035,
040, 042, 045, 048,
055, 056, 063, 071,
083
Realistic
007, 009, 010, 011,
016, 018, 020, 021,
022, 031, 049, 051,
056, 060, 065, 075,
079
Ricoh
047
Runco
034
Samsung
009, 011, 038, 056,
073, 084
Sansui
006, 037, 043, 061
Sanyo
Scott
Sears
Sharp
Shintom
Signature
Signature 2000
Singer
Sony
STS
Sylvania
Symphonic
Tandy
Tashiko
Tatung
Teac
Technics
Teknika
Toshiba
007, 009, 016, 054,
064, 068, 071, 075,
079, 085
008, 011, 017, 028,
030, 057, 065, 072
007, 010, 016, 021,
022, 023, 024, 025,
035, 053, 057, 063,
064, 065, 068, 071,
075, 079
013, 020, 031, 049,
051, 060, 066
004, 025, 032, 061
049
075
047, 061
004, 032, 033, 041,
052, 058, 070, 074,
076, 077, 080
035
018, 026, 027, 028,
044, 072
018, 050, 051, 053,
073, 079
007
010
037
018, 029, 037
036
010, 018, 065
000, 011, 021, 023,
024, 028, 030, 039,
057, 074, 078, 079
Totevision
Unitec
Unitech
Vector Research
009, 010, 065
073
009
005, 006, 011, 012,
053
Video Concepts 005, 006, 011, 012,
039, 053
Wards
009, 010, 011, 016,
018, 020, 024, 025,
031, 035, 049, 051,
056, 057, 060, 065,
066, 079
White
073
Westinghouse
XR-1000
018
Yamaha
005, 006, 007, 014,
037, 053
Zenith
004, 032, 034, 041,
047, 069, 086
HTIB
Lasonic
Panasonic
Venturer
083
084
085
Chapter 4: Menu layout and navigation
Main menu layout
The tables below and on the next page provide a quick overview of your TV’s menu system.
To open the main menus (illustrated below), press
on the remote control or TV control panel.
Icon
Video
Audio
Preferences
Locks
Setup
Item
Option
Mode
Picture Settings
Noise Reduction
Game Mode
Theater Settings
Digital Audio Selector
Audio Settings







Advanced Audio Settings
 [Opens the Advanced Audio Settings menu]
Audio Setup
 [Opens the Audio Setup menu]
CC Selector
Base CC Mode
Digital CC Settings
Input Labeling
Channel Labeling
Menu Language






Channel Browser Setup
 [Opens the Channel Browser Setup menu]
REGZA-LINK Player Control
 [Opens the REGZA-LINK Player Control]
Enable Rating Blocking
Edit Rating Limits
Channels Block
Input Lock
Control Panel Lock
GameTimer
New PIN Code
Installation









REGZA-LINK Setup
Sleep Timer
PC Settings
Logo LED
Sports / Standard / Movie / PC / Preference
[Opens the Picture Settings menu]
[Opens the Noise Reduction menu]
Off / On
[Opens the Theater Settings menu]
[Launches the temporary Audio Selector]
[Opens the Audio Settings menu]
[Launches the temporary CC Selector]
Off / CC1 / CC2 / CC3 / CC4 / T1 / T2/ T3 / T4
[Opens the Digital CC Setup menu]
[Opens the Input Labeling menu]
[Opens the Channel Labeling menu]
English / Français / Español
Off / On
[Opens the Edit Rating Limits menu]
[Opens the Channels block menu]
Off / Video / Video+
Off / On
Off / 30 min / 60 min / 90 min / 120 min
[Opens the New PIN Code entry screen]
[Opens the Installation menu ( page 29)]
Enable REGZA-LINK / TV Auto Input Switch
/ TV Auto Power/ Device Auto Standby / Speaker
Preference
 [Opens the Sleep Timer menu]
 [Opens the PC Settings menu]
 Off/On
27
Chapter 4: Menu layout and navigation
Setup/Installation menu layout
The Installation menu contains the Terrestrial and System Status menus.
To open the Installation menu (illustrated below), press
Setup menu, select Installation, and press
.
Icon
Terrestrial
Item
Option
Input Configuration
Channel Program
Channel Add/Delete
Channel Tuning Mode





Time Zone
on the remote control or TV control panel, open the
[Opens the Input Configuration menu]
[Start]  [Scans for new channels on ANT/CABLE]
[Opens the Channel Add/Delete menu]
Standard / Auto / Digital
Pacific / Alaska / Hawaii / Atlantic / Newfoundland /
Eastern / Central / Mountain
Signal Meter
 [Opens the Signal Meter menu]
System Information
 [Opens the System Information screen]
System Status
Navigating the menu system
• To close a menu instantly, press
Note:
You can use the buttons on the remote control or TV
control panel to access and navigate your TV’s onscreen menu system.
to open the menu system.
• Press
•• The menu background may sometimes
appear black, depending on the signal
the TV is receiving. This is not a sign of
malfunction.
•• The Video sub-menu appears with a black
background, which looks different from other
menus.
• When a menu is open, use the up/down/left/right
arrow buttons (pqtu) on the remote control
or TV control panel to move in the corresponding
direction in the menu.
to save your menu settings or select
• Press
a highlighted item. (A highlighted menu item
appears in a different color in the menu.)
• All menus close automatically if you do not make
a selection within 60 seconds, except the signal
meter menu, which closes automatically after
about 5 minutes.
28
.
Chapter 5: Setting up your TV
Setting the Energy Saving Mode
TOSHIBA Logo LED
When you first turn on the TV, the Menu Language,
and Energy Saving Mode windows will appear by
default.
To select settings:
1無From the Menu Language selection window,
highlight your preferred language and press
Initial Setup
.
You can select TOSHIBA Logo LED either On or Off.
1無Press and open the Setup menu.
2無Highlight Logo LED and press u.
3無Press p or q to select either On or Off and press
.
Menu Language
Setup
Please select a language.
Installation
REGZA-LINK Setup
Sleep Timer
PC Settings
English
Français
Espñol
2無 Next, the Energy Saving Mode setting window will
appear.
For normal home use, press u to select Home and
press
.
Initial Setup
Energy Saving Mode
To use this TV for displaying in a retail showroom,
please select [Retail].
[Home] mode is recommended for normal home
use. (ENERGY STAR® qualified )
R
Retail
Home
Logo LED
Off
Off
On
Configuring the antenna input
source for the ANT/CABLE
terminal
To configure the ANT/CABLE input source:
1無Press and open the Setup menu.
2無Highlight Installation and press .
Selecting the menu language
You can choose from three different languages
(English, French and Spanish) for the on-screen
display of menus and messages.
To select the menu language:
3無(A new set of Installation menu icons will appear,
as shown below.) Open the Terrestrial menu,
highlight Input Configuration, and press
.
1無Press and open the Preferences menu.
2無Highlight Menu Language and press u.
3無Press p or q to select your preferred menu
language and press
.
4無Press t or u to select the input source (Cable or
Antenna) for the ANT/CABLE input on the TV.
5無To save your new settings, highlight Done and press
4無Press
to close the Preferences menu.
. To revert to your original settings, highlight
Cancel and press
.
29
Chapter 5: Setting up your TV
Programming channels into the
TV’s channel memory
When you press
or
on the remote control
or TV control panel, your TV will stop only on the
channels you programmed into the TV’s channel
memory.
Follow the steps below to program channels into the
TV’s channel memory.
Programming channels automatically
4無(A new set of Installation menu icons will
appear, as shown below.) Open the Terrestrial
menu, highlight Channel Program to bring up
the Start, and press
again to begin channel
programming.
Your TV can automatically detect all active channels
in your area and store them in its memory. After the
channels are programmed automatically, you can
manually add or erase individual channels in the
channel memory.
Note:
•• You must configure the ANT/CABLE input
source before programming channels (
page 29).
•• The automatic channel programming process
will erase channels that were previously
programmed into the TV’s memory.
•• To tune the TV to a channel not programmed
in the channel memory, you must use the
Channel Number buttons on the remote
control.
•• Programming channels when the ANT/
CABLE input is configured for Cable will take
substantially longer than when the antenna
input is configured for Antenna. This is
normal; however, once channel programming
is finished, you should not have to repeat
the programming process again unless
your Cable TV service lineup changes
significantly.
To program channels automatically:
1無Configure the antenna input source, if you have
not already done so ( page 29).
2無Press and open the Setup menu.
3無Highlight Installation and press .
The TV will automatically cycle through all the
antenna channels, and store all active channels
in the channel memory. While the TV is cycling
through the channels, the message “Scanning
channels, please wait” appears (as shown
above).
5無To cancel channel programming, press
on
the remote control (or highlight Cancel in the onscreen display and press
).
When channel programming is finished, press
or
to view the programmed channels.
Manually adding and deleting
channels in the channel memory
After automatically programming channels into the
channel memory, you can manually add or delete
individual channels.
To add or delete channels in the channel
memory:
1無From the Setup menu, highlight Installation and
press
. A new set of Installation menu icons
will appear.
(continued)
30
Chapter 5: Setting up your TV
2無Open the Terrestrial
menu, highlightChannel
Add/Delete, and then press
.
To add a channel to the channel memory:
Highlight the unchecked box next to the channel
number you want to add, and then press
to check
the box.
To manually add digital subchannels on a
physical channel:
Use the Channel Numbers and the Dash (
) on
the remote control to enter the channel number (for
example, 56–1).
If the channel is found, the number will be added to
the list and the box will be checked.
If the channel is not found, a message will appear.
To remove a channel from the channel
memory:
Highlight the checked box next to the channel
number you want to remove, and then press
to
uncheck the box.
To save your new settings:
Highlight Done and press
Labeling channels
A list of common channel labels (logos) for various
channels (ABC, CBS, etc.) will be programmed into
the TV. You will be able to view and assign these
logos from the Channel Labeling window. If the
desired channel label is not provided in the list, you
will be able to manually enter/edit labels using the
software keyboard.
To assign channel labels:
1無Press and open the Preferences menu.
2無Highlight Channel Labeling and press .
The Channel Labeling window opens.
3無Press
or
to select the channel you want to
label.
4無Press pqtu to highlight the desired channel
label and press
.
5無Repeat steps 3 and 4 for other channels.
6無To save your settings, highlight Done and press
.
.
To revert to your original settings:
Highlight Cancel and press
before saving.
To remove all channels from the channel
memory:
Highlight Reset and press
Done and press
.
, and then highlight
Note: A video preview of the currently
highlighted channel is provided to assist you in
adding/deleting channels.
To remove encrypted channels from the
channel memory:
If an encrypted channel is accidentally added to
the channel list by programming channels, you can
remove the unwanted encrypted (non-viewable)
channel while you are channel surfing. When you
tune into an encrypted channel, the following
message will appear.
The maximum number of labels that can be
stored is 128.
To remove channel labels:
1無Open the Channel Labeling window.
2無Press or to select the channel for which
you want to remove the label.
3無Press pqtu to highlight No Label and press
.
4無Repeat steps 2 and 3 for other channels.
5無To save your settings, highlight Done and press
.
Press
while the message is on the screen to
remove the unnecessary channel from the channel
list.
If the desired channel label is not available from the
list of presets, you can create a custom label.
(continued)
31
Chapter 5: Setting up your TV
To create and assign a custom label:
Setting the HDMI™ audio mode
1無Open the Channel Labeling window.
2無Press or to select a channel you want to
To set the HDMI audio mode:
label.
3無Press pqu to highlight Custom and press
.
The software keyboard will appear.
1無Press and open the Audio menu.
2無Highlight Audio Setup and press .
3無Press p or q to select HDMI 1 Audio and
then press t or u to select the HDMI 1 audio
mode (Auto, Digital, or Analog). (Auto is the
recommended mode.) See “Connecting an HDMI
or DVI device to the HDMI input” ( page 16).
4無Repeatedly press the corresponding key on the
remote control to highlight the desired character
on the on-screen software keyboard.
5無The highlighted character is entered after you
either press a different key, press u key, or after a
two-second pause.
6無Repeat steps 4 and 5 until you have entered all
desired text.
7無When finished, press .
8無New labels will be added to the list in alphabetical
order and marked with an icon to indicate that
they are custom. Highlight the new custom label
and press
to assign.
Assigned channel labels will be displayed in the
banner, Channel Add/Delete, Channels Block, and
Channel BrowserTM.
To delete the custom label:
1無Open the Channel Labeling window.
2無Highlight the label to be deleted and press
3無Highlight Yes from the deletion confirmation
window and press
.
4無Highlight Done and press
to save changes,
and go back to the Channel Labeling window.
32
.
Mode
Description
Auto
When viewing the HDMI 1 input, if
digital audio from the HDMI input is
available, it will be output. If not, the
TV will automatically detect and output
analog audio from the PC Audio input.
Digital
When viewing the HDMI 1 input,
digital audio from the HDMI input will
be output.
Analog
When viewing the HDMI 1 input,
analog audio from the PC Audio input
will be output.
4無To save your settings, highlight Done and press
.
Note: Because the PC and HDMI-1 inputs
share the same set of analog audio inputs, the
PC Audio menu setting influences the HDMI 1
Audio menu setting. If PC Audio is set to “No,”
the HDMI 1 Audio setting changes to “Auto.”
If PC Audio is set to “Yes,” the HDMI 1 Audio
setting is set to “Digital” and is grayed out in
the menu. (Also see item 7 on page 12 and
“Setting the PC Audio” on page 49.)
Chapter 5: Setting up your TV
Viewing the digital signal meter
Viewing the system status
You can view the digital signal meter in the ANT/
CABLE digital TV input source only.
To view the system status:
To view the digital signal meter:
1無Press and open the Setup menu.
2無Highlight Installation and press .
3無A new set of Installation menu icons will appear.
Open the Terrestrial menu, highlight Signal
Meter, and press
.
4無Press pqtu to select the antenna input and
digital channel whose signal you want to check.
Note:
• The physical digital channel number listed in
the Signal Meter screen may not correspond
to a virtual TV channel number. Contact your
local broadcasters to obtain the RF channel
numbers for your local digital stations.
• The signal strength does not change between
virtual channels on the same physical
channel.
To close the screen and return to the
Terrestrial menu:
Highlight Done and press
.
To return to normal viewing:
Press
.
Setting the time zone
The Time Zone setup will allow you to specify the
correct time zone for your region. This feature will
allow the TV status information to show the correct
time zone information ( page 52).
To set the time zone:
1無From the Setup menu, highlight Installation and
press
. A new set of Installation menu icons
will appear.
2無Highlight Time Zone Setup, and press .
3無Press  or  to select the region, highlight
Done, and then press
.
After the time zone has been set, you will be asked to
set the current Daylight Saving Time status.
To set the Daylight Saving Time status:
1無Press t or u to select Yes or No, highlight Done,
and then press
1無Press and open the Setup menu.
2無Highlight Installation and press .
3無A new set of Installation menu icons will appear.
Open the System Status menu, highlight System
Information, and press
.
4無Press tu to scroll through the menu bar to select
the Sotware Version or Support Information and
view the related information.
Note:
•Sotware Version is for 40RV525R,
40RV52R and 46RV525R.
•Support Information is for 32RV525RZ,
37RV52RZ, 37RV525RZ, 37RV52RZ,
40RV525RZ, 40RV52RZ and 46RV525RZ.
To close the screen and return to the
Installation menu:
Highlight DONE and press
.
To return to normal viewing:
Press
.
Reset Factory Defaults
To reset all settings and channels to their
factory default values:
1無Press and open the Setup menu.
2無Highlight Installation and press . A new set of
Installation menu icons will appear.
3無Open the System Status menu, highlight System
Information, and press
.
4無Press tu to scroll through the menu bar to select
Factory Defaults.
5無Enter your PIN code (or 0000 if no PIN code has
been set).
6無Highlight Yes and press
. The TV will turn
off automatically after a few seconds. After the
TV turns off, unplug the TV power cord and then
plug it in again to complete the reset process.
To cancel the reset:
Highlight No and press
.
.
33
Chapter 6: Using the TV’s features
Selecting the video input source
to view
To select the video input source to view:
1無Press
on the remote control or TV control
panel.
2無And then either:
a) Press 0–7; or
b) Repeatedly press  on the remote control
and then press
to change the input; or
c) Repeatedly press
on the remote control
or TV control panel to change the input.
The current signal source displays in the top right
corner of the Input Selection screen.
Input Selection
0
1
2
3
4
5
6
7
ANT/CABLE
ANT/CABLE
Video 1
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1 REGZA-LINK
HDMI 2
HDMI 3
8 PC
0 - 8 / INPUT to Select
Navigate
Note:
••You can label the video input sources
according to the specific devices you have
connected to the TV ( “Labeling the video
input sources” at right).
••Sources can be “hidden” ( “Labeling the
video input sources” at right).
••“No Video Signal” will appear randomly on the
screen if no signal is received in video input
mode.
••If CEC device is connected to a HDMI input,
the REGZA-LINK icon will appear.
If a REGZA-LINK device with HDMI
switching capability (e.g. Audio Receiver) is
connected to the HDMI input:
Press
on the remote or TV control panel
repeatedly to highlight HDMI 1, HDMI 2, or HDMI 3.
If the connected CEC device has any connected
devices, a separate device selection popup window
will appear.
Press
repeatedly to highlight the desired input
source, and then press
.
Note:
••When selecting REGZA-LINK input sources
from the popup window using
, some
REGZA-LINK devices may automatically turn
on.
••When selecting input sources using ,
you will have to press
to actually select a
particular device from the popup window.
Labeling the video input sources
You can label each video input source according to
the type of device you connected to each source,
from the following preset list of labels:
• – – (default label)
• Audio Receiver
• Cable
• Compact Disc
• DTV
• DVD
• Game Console
• HDMI Switch (HDMI inputs only)
• Laser Disc
• Satellite/DSS
• VCR
• Video Recorder
• Hide (to hide an unused input in the Input Selection
screen and in the Channel Browser™ Inputs list)
Note: If you select PC in the Input Selection
screen, you can choose only “– –”, “Game
Console”, or “Hide” as the label.
To label the video input sources:
1無Press and open the Preferences menu.
2無Highlight Input Labeling and press .
Preferences
CC Selector
Off
Base CC Mode
Off
CC1
Digital CC Settings
CC2
Input Labeling
CC3
Channel Labeling
Menu Language
CC4
English
Channel Browser Setup
T1
T2
REGZA-LINK Player Control
(continued)
34
Chapter 6: Using the TV’s features
3無Press  or  to highlight the video source you
want to label.
Tuning channels using the
Channel Browser™
Input Labeling
Video 1
VCR
Video 2
Cable
ColorStream HD 1
Video Recorder
ColorStream HD 2
Hide
HDMI 1
DTV
HDMI 2
Satellite/DSS
HDMI 3
DV D
--
PC
Reset
Done
4無Press  or  to select the desired label for that
input source. If a particular input is not used, you
can select Hide as the label, which will cause that
input to be “grayed out” in the Input Selection
screen and skipped over when you press
on
the remote control.
5無To save the new input labels, highlight Done and
press
.
To revert to the factory default labels, highlight
Reset and press
.
Input labeling example:
The screen below left shows the default Input Selection
screen (with none of the inputs labeled as a specific
device). The screen below right is an example of how
you could label the inputs if you connected a VCR to
VIDEO 1, Cable TV to VIDEO 2, a video recorder to
ColorStream HD1, a DTV set-top box to HDMI 1, and
a satellite/DSS set-top box to HDMI 2, and a DVD
player to HDMI 3. Also note that the ColorStream
HD2 input is labeled “Hidden”, which means that input
will be skipped over when
is pressed.
Input Selection
0
1
2
3
4
5
6
7
ANT/CABLE
HDMI 2
HDMI 3
8 PC
0 - 8 / INPUT to Select
Input Selection
0
1
2
3
4
5
6
7
ANT/CABLE
Video 1
Video 2
ColorStream HD1
ColorStream HD2
HDMI 1
ANT/CABLE
ANT
ANT/CABLE
VCR
Cable
Video Recorder
ColorStream HD2 (Hidden)
DTV
Input Selection screen
with no inputs labeled.
0 - 8 / INPUT to Select
The Channel Browser™ provides an easy navigation
interface for all your channels and inputs. This
feature allows you to:
• Navigate the contents of all of your inputs.
• Keep a list of your favorite channels (see
“Favorites Browser,” below).
• Keep a history of the last 32 channels or inputs
viewed.
• Quickly surf and tune your recently viewed
channels/inputs from the Channel Browser™
History List (illustrated on the next page).
• Surf via Browse mode (to immediately tune
channels as you highlight them in the Channel
Browser™) or Select mode (to surf over channels
in the Channel Browser™ before you select one
to tune).
• Quickly change inputs from the Inputs List.
• Quickly select REGZA-LINK devices from the
REGZA-LINK List.
Favorites Browser
The Favorites Browser allows you to quickly set up a
favorite channels/inputs list that is integrated into the
Channel Browser™.
To add a favorite channel/input:
1無Tune to the channel or input.
for 3 seconds.
2無Press and hold
Note: Additions are added to the beginning of
the Favorites list on the left side of the Channel
Browser™.
To delete a favorite channel/input:
Satellite/DSS
DVD
1無Press
8 PC
Navigate
Tuning channels
Navigate
Input Selection screen
with all inputs labeled
except input 4, which
has been hidden.
To clear the input labels:
1無Press and open the Preferences menu.
2無Highlight Input Labeling and press .
3無Highlight Reset and press .
to open the Favorites browser
list.
2無Highlight the channel or input to delete by
pressing  or .
for 3 seconds. The channel/
3無Press and hold
input will be removed from the Favorites list.
To set up the Channel Browser™:
1無From the Preferences menu, highlight Channel
Browser Setup and press
.
2無Press  to highlight Navigation, and then press
 or  to select either Browse Mode or Select
Mode.
(continued)
35
Chapter 6: Using the TV’s features
Elements of the ChannelBrowser™
3無Press  to highlight History List, and then press
 or  to select the setting you prefer: either On,
or Off.
Note: History List will be cleared every time
the TV is powered off.
4無Press  to highlight ANT/CABLE List, and then
press  or  to select On or Off.
5無Press  to highlight Inputs List, and then press
 or  to select On or Off.
6無Press  to highlight Favorites List, then press 
or  to select On or Off.
7無Press  to highlight REGZA-LINK List, and then
press  or  to select On or Off.
Note: REGZA-LINK List will be automatically
grayed out and set to Off when Enable
REGZA-LINK is switched to Off. (See “To
set the REGZA-LINK Setup” on page 51 for
more information.)
8無To save your entries, highlight Done and press
. To return to factory defaults, highlight Reset
and press
.
To open the Channel Browser™:
• Press
• Press
 or  on the remote control.
 to surf backward through the previously
tuned 32 channels in the History list, the channels
in the ANT/ CABLE channel list, the inputs in
the Inputs list, the REGZA-LINK devices in the
REGZA-LINK list, or the favorite channels/inputs
in the Favorites list.
• Press  to surf forward through the channel
History, the ANT/CABLE channel list, the
Inputs list, the REGZA-LINK list, or the favorite
channels/inputs in the Favorites list.
1無 Current list (History, ANT/CABLE, Inputs,
Favorites, or REGZA-LINK)
2無 Input type
3無 Channel or input currently being viewed
4無 Channel or input that is currently
highlighted in the browser
5無 Channels stored in the History List
6無 Channel labels
To toggle among the available lists:
After opening the Channel Browser™, press  or
 to toggle among History, ANT/CABLE, Inputs,
Favorites, and REGZA-LINK.
Note:
••The Channel Browser™ opens in History
List by default. Once another list has been
selected, the Channel Browser™ will open in
the last selected list.
••If all lists are turned off, pressing ,
, or
will not display the Channel
Browser™. If Favorites List is turned off,
will have no effect.
will bring up the Channel
••Pressing
Browser™ Favorites list regardless of the last
selected list in the Channel Browser™.
To tune to a channel or input in Browse
mode:
1無While watching TV, press
 or  to
open the Channel Browser™ and surf back to a
previous item or surf forward to the next item in
the list.
In Browse mode, when you stop on an item in the
Channel Browser™, it will be highlighted and
the TV will automatically tune to the channel or
input.
2無Press
36
to close the Channel Browser™.
Chapter 6: Using the TV’s features
To tune to a channel or input in Select mode:
Setting the Channel Tuning Mode
1無While watching TV, press
This feature allows you to choose how tuning will be
handled for analog and digital channels when the TV
is in Antenna mode.
 or  to open the
Channel Browser™ and surf back to a previous item
or forward to the next item in the list.
In Select mode, when you stop on an item in the
Channel Browser™, it will be highlighted but you
must press
to tune the TV to the highlighted
item.
Note: To use this feature, the Input Configuration
must be set to Antenna ( page 29).
The channel tuning mode has three options.
Mode
Description
Standard
Both analog and digital channels can
be tuned normally
Adding and clearing channels and inputs
in the History List
Auto
(default)
Adding channels and inputs to the History
List:
Digital channels will have priority when
manually entering a channel number
using the Channel Number (0-9) on the
remote control, analog channels can
still be tuned by
/
, if available
Digital
Only digital channels can be tuned
2無Press
3無Press
to tune the TV to the highlighted item.
to close the Channel Browser™.
As a channel or input is tuned, the Channel Browser™
adds it to the History List and displays it on the “right
side” of the Channel Browser™. Previously tuned
channels/inputs are “shifted” to the left, eventually
moving off the left side. Press  to surf backward
through the previously tuned channels/inputs. Any
channel or input that is tuned repeatedly will not be
repeated in the History List, but instead is moved to
the end of the list on the right side of the Channel
Browser™.
The Channel Browser™ will store the following
channels:
• All channels that are tuned using the numeric buttons
on the remote control.
or
on the
•All channels that are tuned using
remote control.
Note: Whenever an item is selected that cannot
be tuned (for various reasons), the TV will
automatically tune to the previously viewed
channel or input.
Clearing channels from the History List:
•Reconfiguring the ANT/CABLE input will clear the
History List.
Note: See page 29 for details on configuring
the antenna input.
• Once 32 channels or inputs are stored in the History
Note: Digital mode will be most useful after
analog channels are shut down by the
government in 2009.
To set the Channel Tuning Mode:
1無From the Setup menu, highlight Installation and
press
. A new set of Installation menu icons
will appear.
2無Open the Terrestrial menu, highlight Channel
Tuning Mode, and then press  and   to
select your desired mode.
Note:
••The Channel Add/Delete & Channels Block
windows as well as the Channel Browser ANT/
CABLE list will be updated automatically when
you change the mode. Also, the History List will
be cleared, but the Favorites List will be saved.
••Even if the Channel Tuning Mode is set to
Digital, analog channel 3 will still be the
default channel to prevent the initial case
where no digital channels have been found in
prior channel scans. (Channel Add/Delete will
not have anything listed until a scan is done.)
List, the oldest item will be removed from the list
when a new channel or input is tuned.
•Turning off the TV will clear the History List.
37
Chapter 6: Using the TV’s features
Tuning to the next programmed
channel
Switching between two channels
using SurfLock™
To tune to the next programmed channel:
The SurfLock™ feature temporarily “memorizes” one
channel to the
button, so you can return to that
channel quickly from any other channel by pressing
. To memorize a channel to the
button:
Press
panel.
or
on the remote control or TV control
Note: This feature will not work unless you
program channels into the TV’s channel memory
( page 30).
Tuning to a specific channel
(programmed or unprogrammed)
Tuning analog channels:
Press the Channel Number (0–9) on the remote
control. For example, to select channel 125, press 1, 2,
5, then
.
Tuning digital channels:
Press the Channel Number (0–9) on the remote
control, followed by the dash (
) button and then
the sub-channel number. For example, to select digital
channel 125-1, press 1, 2, 5, –, 1, then
.
Note: If a digital channel is not programmed—
either through the automatic channel scan (
page 30) or the channel add/delete function (
page 31)—you will have to tune the RF channel
using the Channel Number and dash (
) on
the remote control.
Switching between two channels
using Channel Return
The Channel Return feature allows you to switch
between two channels without entering an actual
channel number each time.
1無Tune the TV to the channel you want to program
into the
button.
for about 2 seconds until
2無Press and hold
the message “Memorized” appears on-screen.
The channel has been programmed to the
button.
3無You can then change channels repeatedly, and
when you press
will be tuned.
, the memorized channel
The TV will return to the memorized channel one
time only. Once you press
and then change
channels again, the CH RTN memory will be cleared
and the button will function as Channel Return,
by switching back and forth between the last two
channels that are tuned.This feature also works for
external inputs.
Selecting the picture size
You can view many program formats in a variety of
picture sizes—Natural, TheaterWide 1, TheaterWide
2, TheaterWide 3, Full, 4:3 HD, Native, and Dot by Dot
(available in PC Mode Only).
Note: The “picture size” illustrations are
examples only. The format of the image (in any
of the picture sizes) will vary depending on the
format of the signal you are currently watching.
Select the picture size that displays the current
program the way that looks best to you.
1無Select the first channel you want to view.
2無Select a second channel using the Channel
You can save separate picture size preferences for
each input on your TV.
3無Press
on the remote control. The previous
channel will display. Each time you press
, the
TV will switch back and forth between the last two
channels that were tuned.
on the remote control.
1無Press
While
the
Picture
Size screen is open, you can do
2無
Note: If you press
from a non-antenna
input, the TV will return to the last-viewed
input.
.
•Repeatedly press
• Press the corresponding Number button (0–6)
Number buttons (and the dash (
selecting a digital channel).
) button if
To select the picture size using the remote
control:
one of the following to select the desired picture
size:
while the Picture Size screen is open.
•Press  or  while the Picture Size screen is
open.
38
(continued)
Chapter 6: Using the TV’s features
To select the picture size using the menus:
1無Select Picture Size in the Theater Settings menu.
2無Press  or  to select the desired picture size
setting.
3無Highlight Done and press
Picture Size
TheaterWide 2
(for letter box programs)
.
Note: Some of the picture sizes may not be
available depending on the receiving signal
format (those will be “grayed out” in the Picture
Size screen).
Using these functions to change the
picture size (i.e., changing the height/
width ratio) for any purpose other than your
private viewing may be prohibited under
the Copyright Laws of the United States
and other countries, and may subject you
to civil and criminal liability.
Note: If you select one of the TheaterWide®
picture sizes, the top and bottom edges of the
picture (including subtitles or captions) may be
hidden. To view the hidden edges, either scroll
the picture (TheaterWide 2 and 3 only) or try
viewing the program in Full or Natural picture
size.
Picture Size
ABCDEFG----------------
The top and bottom edges of the picture may be
hidden*.
TheaterWide 3
(for letter box programs with
subtitles)
ABCDEFG----------------
ABCDEFG--------------------------
The top and bottom edges are hidden*.
Full
(for 16:9 [480i, 480p] source
programs only)
Natural
• If receiving a squeezed 4:3 format program, the
Some program formats will display with sidebars
and/or bars at the top and bottom.
TheaterWide 1
(for 4:3 format programs)
The center of the picture remains close to its original
proportion, but the left and right edges are stretched
wider to fill the screen.
picture is stretched wider to fill the width of the
screen, but not stretched taller.
• None of the picture is hidden.
4:3 HD
(for 720p, 1080i, and 1080p program
sources only)
Picture is not distorted from original size.
(continued)
39
Chapter 6: Using the TV’s features
To set the scroll settings:
Picture Size
Native
(for 480i (HDMI), 480p (HDMI), 720p,
1080i, and 1080p signal programs)
• If receiving a 480i (HDMI), 480p (HDMI), 720p,
1080i, or 1080p signal program, Native mode scales
the video to display the entire picture within the
borders of the screen (i.e. no overscanning).
• This is especially useful for external HD sources
such as DVHS movies, or PC graphics.
Note:
••This mode is supported only for HDMI
(1080p,1080i, 720p, 480p, and 480i), ColorStream
(1080i and 720p), and ANT/ CABLE (digital)
inputs (1080p,1080i, and 720p).
••Depending on the input signals, the border of
the picture may be hidden, displayed in black,
or noisy.
Dot by Dot
(for VGA, SVGA, XGA, WXGA, and
SXGA sources only)
The “Dot by Dot” picture is non-scaling display.
Depending on the input signal formats, picture is
displayed with sidebars and/or bars at the top and
bottom. (Example: VGA input source)
** To view the hidden areas (such as subtitles or
captions), see below “Scrolling the TheaterWide®
picture”.
®
Scrolling the TheaterWide picture
(TheaterWide 2 and 3 only)
You can set separate scroll settings for the TheaterWide 2
and TheaterWide 3 modes for each input.
40
1無Press and open the Video menu.
2無Highlight Theater Settings and press
.
3無In the Picture Size field, select either TheaterWide
2 or TheaterWide 3 (you cannot scroll in any other
mode).
4無Press  to highlight the Picture Scroll field.
5無Press  or  to scroll the picture up and down
as needed.
6無To save the new settings, highlight Done and
press
. To revert to the factory defaults,
highlight Reset and press
.
Note: When receiving a signal at 480i
resolution, the picture scroll function may have
limited adjustment range.
Using the auto aspect ratio feature
When the auto aspect ratio feature is set to On, the
TV will automatically select the picture size when
one of the following input sources is received:
• A 480i, 480p, 720p, 1080i digital signal from the
ANT/CABLE input
• A 480i signal from the VIDEO 1 or VIDEO 2 input
•A 480i signal from the ColorStream HD1, or HD2
input
• A 480i, 480p, 720p, 1080i, 1080p, or VGA (60Hz)
signal from the HDMI 1/2/3 input
Aspect ratio of
signal source
Automatic aspect size
(automatically selected when
Auto Aspect is On)
4:3 normal
Natural (with sidebars)
4:3 letter box
TheaterWide 2
16:9 full
Full
Not defined (no
The current picture size you
ID-1 data or
set under “Selecting the
HDMI aspect data) picture size” on page 38.
Note: The auto aspect ratio feature is not
applicable to PC input.
Chapter 6: Using the TV’s features
To turn on the auto aspect ratio feature:
1無Press and open the Video menu.
2無Highlight Theater Settings and press .
3無In the Auto Aspect Ratio field, select On.
4無To save the new settings, highlight Done and press
. To revert to the factory defaults, highlight
Reset and press
.
To turn off the auto aspect ratio feature:
Select Off in step 3 above.
Selecting the cinema mode
When you view a DVD (3:2 pulldown processed)
from a DVD player connected to the VIDEO 1, VIDEO
2, ColorStream HD-1, ColorStream HD-2 (component
video), or HDMI inputs on the TV, smoother motion
can be obtained by setting the Cinema Mode to Film.
To set the Cinema Mode to Film:
(available for 480i and 1080i signals)
1無Press and open the Video menu.
2無Highlight Theater Settings and press .
3無In the Cinema Mode field, select Film.
4無To save the new settings, highlight Done and press
. To revert to the factory defaults, highlight
Reset and press
.
Adjusting the picture
Selecting the picture mode
You can select your desired picture settings from four
different modes, as described below.
Mode
Picture Quality
Sports
Bright and dynamic picture (factory
setting)
Standard
Standard picture settings (factory
setting)
Movie
Lower contrast for darkened room
(factory setting)
PC
Designed for viewing of PC tables
and documents
Preference
Your personal preferences
Note: PC mode is available for HDMI and PC
inputs only (grayed out for other input sources).
To select the picture mode using the menu
system:
1無Press and open the Video menu.
2無Highlight Mode and press .
To set the Cinema Mode to Video:
Select Video in step 3 above.
Using the FREEZE feature
To use the FREEZE feature:
to make the
1無When viewing the TV, press
picture a still picture.
2無To return to the moving picture, press
again (or any other button).
3無Press  or  to select the picture mode you
prefer and press
.
Note: If the TV is left in FREEZE mode for
more than 15 minutes, the FREEZE mode
will automatically be released and the TV will
return to moving picture.
Using the FREEZE function for any purpose
other than your private viewing may be
prohibited under the Copyright Laws of the
United States and other countries, and may
subject you to civil and criminal liability.
Note: The picture mode you select affects
the current input only. You can select a
different picture mode for each input.
41
Chapter 6: Using the TV’s features
Adjusting the picture quality
Using the closed caption mode
You can adjust the picture quality (Contrast,
Backlight, DynaLight™, Brightness, Color, Tint, and
Sharpness) to your personal preferences.
Base closed captions
Selection
Pressing 
Pressing 
Contrast
lower
higher
Backlight*
darker
lighter
DynaLight**
On/Off
On/Off
Brightness
darker
lighter
Color
paler
deeper
Tint
reddish
greenish
Sharpness
softer
sharper
** Backlight
This feature adjusts the brightness of the
entire screen. When in video mode and no
signal is input, this will automatically be set to
0. (Settings are stored in memory.)
**DynaLight
This function automatically strengthens the
black coloring of dark areas in the video
according to the level of darkness.
The closed caption mode has two options:
• Captions—An on-screen display of the dialogue,
narration, and sound effects of TV programs and
videos that are closed captioned (usually marked
“CC” in program guides).
•Text—An on-screen display of information not
related to the current program, such as weather or
stock data (when provided by individual stations).
To view captions or text:
1無Press and open the Preferences menu.
2無Highlight Base CC Mode and press .
3無Press  or  to select the desired closed caption
mode and press
.
•To view captions:
Highlight CC1, CC2, CC3, or CC4. (CC1 displays
translation of the primary language in your area.)
To adjust the picture quality:
1無Press and open the Video menu.
2無Highlight Picture Settings and press .
3無Press  or  to select the picture quality you
want to adjust (Contrast, Backlight, DynaLight,
Brightness, Color, Tint, or Sharpness), and then
press  or  to adjust the setting, as described in
the table above.
Note: If the program or video you selected
is not closed captioned, no captions will
display on-screen.
•To view text:
Highlight T1, T2, T3, or T4.
4無To save the new settings, highlight Done and
press
. You can use any of the picture modes
( “Selecting the picture mode,” above left) as a
starting point for adjusting the picture settings.
To revert back to the base mode that you began
adjusting the picture settings from, highlight
Reset and press
.
The picture qualities you adjusted are automatically
saved in the Preference mode ( “Selecting the
picture mode,” above left) until Reset is selected.
42
Note: If text is not available in your area, a
black rectangle may appear on screen. If this
happens, set the Base CC Mode to Off.
•To turn off the closed caption mode:
Select Off in step 3 above.
Note: A closed caption signal may not display
in the following situations:
••When a videotape has been dubbed
••When the signal reception is weak
••When the signal reception is non-standard
Chapter 6: Using the TV’s features
Digital CC Settings
You can customize the closed caption display
characteristics by changing the background color,
opacity, text size, type, edge, and color.
Note:
••This feature is available for digital channels
only.
••You cannot set the Caption Text and
Background as the same color.
To customize the closed captions:
1無Press and open the Preferences menu.
2無Highlight Digital CC Settings and press .
3無Press  or  to highlight the characteristic you
want to change, and then press  or  to select
the format for that characteristic (see table below).
4無To save the new settings, highlight Done and press
. To revert to the factory defaults, highlight
Reset and press
.
Caption Size
Auto, Small, Standard, Large
Caption Text
Type
Auto, Default, Mono w. Serif,
Prop. w. Serif, Mono w/o
Serif, Prop. w/o Serif, Casual,
Cursive, Small Capitals
Caption Text
Edge
Auto, None, Raised,
Depressed, Uniform, Left
Drop Shadow, Right Drop
shadow
Caption Text
Color
Auto, Black, White, Red,
Green, Blue, Yellow, Magenta,
Cyan
Text Foreground Auto, Transparent,
Opacity
Translucent, Flashing, Solid
Background
Color
Auto, Black, White, Red,
Green, Blue, Yellow, Magenta,
Cyan
Text Background Auto, Transparent,
Opacity
Translucent, Flashing, Solid
Caption Text
Edge Color
Auto, Black, White, Red,
Green, Blue, Yellow, Magenta,
Cyan
CC Selector
You can use the CC Selector to temporarily override
the default analog caption mode (set in Base CC
Mode) for a particular channel. However, once you
change to another analog channel, the closed caption
setting will automatically change back to the current
Base CC Mode setting.
You can also use the CC Selector to select digital
closed caption services (if available). When such
services are not available, the CC Selector presents a
default list of services. If the selected service is not
available, the next best service will be used instead.
To select closed captions:
1無Press and open the Preferences menu.
2無Highlight CC Selector and press .
3無Press  or  to select Closed Caption, and then
press  or  to select the desired service.
4無Press
.
Adjusting the audio
Muting the sound
Press
on the remote control to partially reduce (1/2
MUTE) or turn off (MUTE) the sound. Each time you
press
, the mute mode will change in the following
order:
1/2 Mute
Mute
Volume
If the closed caption mode is set to Off when you
select “MUTE” mode, the closed caption feature is
automatically activated if the TV program is Closed
Captioned. To mute the audio without automatically
activating the closed caption feature, use
to
set the volume to 0. See “Using the closed caption
mode” ( page 42) for more information on closed
caption modes.
Using the digital audio selector
You can use the Digital Audio Selector to
conveniently switch between audio tracks on a digital
channel (for those channels that have multiple audio
tracks). This temporarily overrides the audio track
chosen by the language option under Audio Setup (
“Selecting stereo/SAP broadcasts” on page 44).
To use the digital audio selector:
1無Press
and open the Audio menu.
(continued)
43
Chapter 6: Using the TV’s features
2無Highlight Digital Audio Selector and press
.
Audio
Digital Audio Selector
Audio Settings
Advanced Audio Settings
Audio Setup
3無Press  or  to select Audio, and then press 
or  to select the desired service.
4無Press
.
Selecting stereo/SAP broadcasts
The multi-channel TV sound (MTS) feature allows
you to output high-fidelity stereo sound. MTS
also can transmit a second audio program (SAP)
containing a second language, music, or other audio
information (when provided by individual stations).
When the TV receives a stereo or SAP broadcast, the
word “STEREO” or “SAP” appears on-screen when
is pressed.The MTS feature is only available
for analog signals on the ANT/CABLE input.
To listen to stereo sound:
1無Press and open the Audio menu.
2無Highlight Audio Setup and press .
3無In the MTS field, select Stereo.
4無To save the new settings, highlight Done and
press
.
To reset the settings to the factory defaults,
highlight Reset and press
.
Note:
••You can typically leave the TV in Stereo
mode because it will automatically output
the type of sound being broadcast (stereo
or monaural).
••If the stereo sound is noisy, select Mono to
reduce the noise.
To listen to an alternate language on an
ATSC digital station (if available):
Highlight the Language field in step 3 above, and
then press  or  to select the language you prefer.
To listen to a second audio program on an
analog station (if available):
Select SAP in step 3 above.
Note:
••A second audio program (SAP) can be heard
only on those TV stations that offer it. For
example, a station might broadcast another
44
language as a second audio program. If you
have SAP on, you will see the current program
on the screen but hear the other language
instead of the program’s normal audio.
••If you have SAP on and the station you are
watching is not broadcasting a second audio
program, the station’s normal audio will be
output. However, occasionally there is no
sound at all in SAP mode. If this happens, set
the MTS feature to Stereo mode.
Adjusting the audio quality
You can adjust the audio quality by adjusting the
bass, treble, and balance.
To adjust the audio quality:
1無Press and open the Audio menu.
2無Highlight Audio Settings and press .
3無Press  or  to highlight the item you want to
adjust (Bass, Treble, or Balance).
4無Press  or  to adjust the level.
•• makes the bass or treble weaker or
increases the balance in the left channel
(depending on the item selected).
•• makes the bass or treble stronger or
increases the balance in the right channel
(depending on the item selected).
5無To save the new settings, highlight Done and press
. To reset the settings to the factory defaults,
highlight Reset and press
.
Selecting the optical audio output
format
You can use this feature to select the optical audio
output format when you connect a Dolby Digital
decoder or other digital audio system to the Optical
Audio Out terminal on the TV (see “Connecting a
digital audio system” on page 18).
To select the optical audio output format:
1無Press and open the Audio menu.
2無Highlight Audio Setup and press .
3無In the Optical Output Format field, select either
Dolby Digital or PCM, depending on your device.
4無To save the new settings, highlight Done and press
. To revert to the factory defaults, highlight
Reset and press
.
Chapter 6: Using the TV’s features
Using the Dolby® Digital Dynamic
Range Control feature
This dynamic range control feature causes the ATSC
dynamic range to be further compressed, allowing
you to switch from ATSC to analog broadcasts at the
same dynamic range.
PIN code has not been stored. Press the Channel
Number buttons to enter a new four-digit code,
enter the code a second time to confirm, and
press
.
To use the Dolby Digital Dynamic Range
Control:
1無Press and open the Audio menu.
2無Highlight Audio Setup and press .
3無In the Dolby Digital Dynamic Range Control field,
select Compressed. When Standard is selected,
the audio is output with minimal compression.
4無To save the new settings, highlight Done and
press
.
To revert to the factory defaults, highlight Reset
and press
.
Note:
••This item will be grayed out for NTSC signals,
Video, ColorStream, and PC inputs.
••The Dolby Digital Dynamic Range Control will
function in relation to Optical Output Format
(PCM mode).
Using the Locks menu
The Locks menu includes the Enable Rating
Blocking, Edit Rating Limits, Channels Block, Input
Lock, Front (control) Panel Lock, and New PIN Code
features. You can use these features after entering the
correct PIN code.
Entering the PIN code
1無Press
and highlight the Locks menu icon.
•The Locks/Active screen appears if the PIN code
is already stored. Use the Number buttons to
enter your four-digit code and press
.
If the wrong PIN code is entered, the message
“Incorrect PIN code, please try again!” appears.
Highlight Retry and press
. Enter the code again
and press
.
When the correct PIN code is entered, the Locks menu
opens.
If you cannot remember your PIN code
While the PIN code entering screen is displayed, press
four times within five seconds. The PIN code will
be cleared and you can enter a new PIN code.
Changing your PIN code
1無Press and highlight the Locks menu icon.
2無Press  to display the PIN code entering screen.
3無Enter your four-digit PIN code and press .
4無Press  to highlight New PIN Code and press .
5無Press the Number buttons to enter a new fourdigit code. Reenter the PIN code to confirm it.
6無Press
. The new PIN code is now active.
Blocking TV programs and movies
by rating (V-Chip)
2無Press , which displays the PIN code entry
Some TV programs and movies include signals that
classify the content of the program (violence, sex,
dialog, language). The V-Chip feature in this TV
detects the signals and blocks the programs according
to the ratings you select. (For rating descriptions, see
the tables on the next page.)
screen.
•The Lock System screen (below) appears if a
45
Chapter 6: Using the TV’s features
To block and unblock TV programs and
movies:
To download the additional rating system
(if available):
1無Press and highlight the Locks menu icon.
2無Press  to display the PIN code entering screen.
3無Enter your four-digit PIN code and press .
4無Press  to highlight Enable Rating Blocking.
5無Press  and  to select On, and then press .
1無Press and highlight the Locks menu icon.
2無Press  to display the PIN code entering screen.
3無Enter your four-digit PIN code and press .
4無Press  to highlight Enable Rating Blocking.
5無Press  and  to select On, and press .
6無Press  to highlight Edit Rating Limits and press
. The Edit Rating Limits screen appears.
7無Highlight Alt RS and press
Ratings screen will appear.
. The Edit Alternate
Note:
6無Press  to highlight Edit Rating Limits and press
. The Edit Rating Limits screen appears.
7無Press   and then press
to select the
level of blocking you prefer. A box with an “ ”
is a rating that will be blocked. As you highlight
a rating, a definition for the rating appears at the
bottom of the screen.
8無When done selecting the ratings you want to
block, highlight Done and press
.
Note: Above selection of blocking level is for
U.S V-Chip system. For Canada rating, you can
highlight the “Canada RS” then press
, another
“Canadian Rating Menu” screen will appear.
Downloading an additional rating
system for blocking TV programs and
movies
In the future, an additional rating system may become
available for use in selectively blocking programs.
Note: The currently tuned station must be
receiving a digital signal before an additional
rating system can be downloaded.
46
••The Alt RS button will only be available
if an additional rating system is currently
available.
••It may take several minutes for the TV to
download the additional rating system.
••The information displayed in the Alternate
Ratings screen will depend on the
configuration of the additional rating
system available at the time of download.
8無Press   and then press
to select the
level of blocking you prefer. A box with an “ ”
is a rating that will be blocked.
9無When you are finished selecting the ratings you
want to block, highlight Done and press
.
10In the Edit Rating Limits screen, highlight Done
and press
.
Note:
••The additional rating system can only be
downloaded one time. You will not be able to
download any updates to the rating system
should such updates become available.
••The additional rating system is not designed,
transmitted, or controlled by the TV or
Toshiba, nor is the availability of an additional
rating system determined or controlled by
Toshiba. Similarly, the rating of programs in
an additional rating system is not determined,
transmitted, or controlled by the TV or Toshiba.
••The additional rating system is an evolving
technology; therefore, availability, content, and
format may vary.
Chapter 6: Using the TV’s features
Independent rating system for broadcasters
Ratings
Description and Content themes
TV-MA
Mature Audience Only (This
program is specifically designed
to be viewed by adults and
therefore may be unsuitable for
children under 17.)
L) Crude or indecent language S)
Explicit sexual activity V) Graphic
violence
TV-14
Parents Strongly Cautioned (This
program contains some material
that many parents would find
unsuitable for children under 14
years of age.)
D) Intensely suggestive dialog
L) Strong, coarse language
S) Intense sexual situations V)
Intense violence
TV-PG
Parental Guidance Suggested
(This program contains material
parents may find unsuitable for
younger children.)
D) Some suggestive dialog L)
Infrequent coarse language
S) Some sexual situations V)
Moderate violence
TV-G
General Audience (Most parents
would find this program suitable
for all ages.)
TV-Y7,
TVY7FV
Directed to Older Children (This
program is designed for children
age 7 and above. Note: Programs
in which fantasy violence may be
more intense or more combative
than other programs in this
category are designated TV-Y7FV.)
TV-Y
All Children (This program is
designed to be appropriate for all
children.)
Independent rating system for movies
Ratings
Description and Content themes
X
X-rated (For adults only)
NC-17
Not intended for anyone 17 and
under
R
Restricted (Under 17 requires
accompanying parent or adult)
PG-13
Parents Strongly Cautioned (Some
material may be inappropriate for
children under 13)
PG
Parental Guidance Suggested
(Some material may not be
suitable for children)
G
General Audience (Appropriate
for all ages)
Note:
••If you place an “ ” in the box next to “
‘None’ Rated,” programs rated “None” will
be blocked; however, programs that do not
provide any rating information will not be
blocked.
••To display the rating of the program you are
watching, press
on the remote control. If
it is rated “None,” the word “NONE” appears
in the RECALL screen (as shown below right).
If rating information is not provided, no rating
will appear in the RECALL screen.
Blocking channels
With the Channels Block feature, you can block
specific channels. You will not be able to tune
blocked channels unless you unlock them.
To block channels:
1無Press and highlight the Locks menu icon.
2無Press  to display the PIN code entering screen.
3無Enter your four-digit PIN code and press
( page 45).
4無Press  to highlight Channels Block and then
press
. A list of the channels available for that
input will be displayed along with the call letters
for each channel, if available.
5無Press  to highlight the channel you want to
block and press
, which puts an “ ” in the
box next to that channel.
47
Chapter 6: Using the TV’s features
and channels 3 and 4. You will not be able to view the
input sources or channels until you unlock the inputs.
To lock/unlock the video inputs:
1無From the Locks menu, Press  to display the
PIN code entering screen.
6無Repeat step 5 for other channels you want to
block.
7無Highlight Done and press
2無Enter your four-digit PIN code and press .
3無Press  to highlight Input Lock and press .
4無Press  or  to select the level of video input
locking you prefer, as described below.
Mode
.
To unblock individual channels:
Video
Video+
Locks VIDEO 1, VIDEO 2,
ColorStream HD1/HD2, HDMI 1,
HDMI 2, HDMI 3, PC and channels 3
and 4.
• Select Video+ if you play video
tapes via an ANT/CABLE input.
Off
Unlocks all video inputs and channels
3 and 4.
In step 5 above, press  to highlight the channel
you want to unblock, press
to remove the “ ”
from the box, highlight Done and press
.
To block all channels at once:
Highlight Block All in step 5 on previous page and
then highlight Done and press
.
To unblock all locked channels at once:
Highlight Allow All in step 5 on previous page and
then highlight Done and press
.
Unlocking programs temporarily
If you try to tune the TV to a program that exceeds
the rating limits you set, the TV will enter program
lock mode and the following message will appear onscreen:
This program exceeds the rating limit you set.
Push 'MUTE' to enter PIN.
You can either temporarily unlock the program or
select an unlocked program to watch.
To temporarily unlock the program:
1無Press .
2無Enter your four-digit PIN code and press
. If
the correct code is entered, the program lock mode
is released and the normal picture appears. All
locking is disabled until the TV is turned off, and
will be enabled when the TV is turned on again.
Using the input lock feature
You can use the Input Lock feature to lock the
video inputs (VIDEO 1, VIDEO 2, ColorStream HD-1,
ColorStream HD-2, HDMI 1, HDMI 2, HDMI 3 and PC)
48
Description
Locks VIDEO 1, VIDEO 2,
ColorStream HD1/HD2, HDMI 1,
HDMI 2, HDMI 3, and PC.
5無Press
.
®
Using the GameTimer
You can use the GameTimer to set a time limit for
playing a video game (30–120 minutes). When the
GameTimer expires, the TV enters Input Lock mode
and locks out the input source for the video game
device.
To set the GameTimer®:
1無From the Locks menu, press  to display the
PIN code entering screen.
2無Enter your four-digit PIN code and press .
3無Press  to highlight GameTimer and press .
4無Press  or  to select the length of time until
the Input Lock is activated (30, 60, 90, or 120
minutes) and press
.
To cancel the GameTimer®:
Select Off in step 4 above.
To deactivate the Input Lock once the
GameTimer® has activated it:
Set the Input Lock to Off ( “Using the input lock
feature” as described).
Chapter 6: Using the TV’s features
Note:
••A message will appear when 10 minutes,
3 minutes, and 1 minute remain on the
GameTimer.
••If the TV loses power with time remaining on the
GameTimer, when power is restored the TV will
enter Input Lock mode (as if the GameTimer
had been activated) and you will have to
deactivate the Input Lock (as described
before).
picture are cut off, readjust the Horizontal Position
and Vertical Position. If the picture is affected by
interference, readjust the Clock Phase and Sampling
Clock.
To adjust the PC settings:
1無Repeatedly press
to select PC input mode
( “Selecting the video input source to view”
page 34).
2無Press and open the Setup menu.
3無Highlight PC Settings and press .
Using the control panel lock feature
You can lock the control panel to prevent your
settings from being changed accidentally (by
children, for example). When the control panel lock
is On, none of the controls on the TV control panel
will operate except POWER.
To lock the control panel:
1無Press and highlight the Locks menu icon.
2無Press  to display the PIN code entering screen.
3無Enter your four-digit PIN code and press .
4無Press  to highlight Control Panel Lock.
5無Press  and  or  to highlight On and press
Installation
PC Settings
Note: If a PC is not connected or there is no
pc input signal, this feature will be grayed
out in the Setup menu.
4無Press  or  to highlight the item you want to
adjust.
5無Press  or  to make the appropriate
adjustments.
. When the control panel is locked and any
button on the control panel (except POWER)
is pressed, the message “NOT AVAILABLE”
appears.
Note: The screen is disrupted momentarily
when adjusting the PC settings. This is not a
sign of malfunction.
Mode
Description
To unlock the control panel:
Horizontal
Position
Highlight Off in step 5 above, or press and hold the
VOLUME – button on the TV control panel for about
10 seconds until the volume icon appears.
Moves the picture left/right.
The adjustment range is within ±50 from
center.*
Vertical
Position
Moves the picture up/down.
The adjustment range is within ±10 from
center.*
Clock
Phase
Helps to reduce noise and sharpen the
picture.
The adjustment range is within ±16 from
center.*
Using the PC settings feature
You can view an image from a PC on the TV screen.
When a PC is connected to the TV's PC IN
terminal, you can use the PC Settings feature to
make adjustments to the image. If the edges of the
(continued)
49
Chapter 6: Using the TV’s features
Sampling
Clock
Helps to reduce noise and minimize
periodic vertical stripes on the screen.
The adjustment range is within ±10 from
center.*
Auto
Adjust
Highlight this item then press
to get an optimum adjustment
automatically.
** The default settings may vary depending on
the input signal format.
Setting the PC Audio
This function allows you to output or mute the sound
from your PC when connecting using the PC IN
terminal and an analog RGB cable. ( page 19)
To set the PC Audio:
1無Press and open the Audio menu.
2無Highlight Audio Setup and press .
3無Press  or  to select PC Audio and then press
 or  to select No or Yes.
Yes: When viewing the PC input, the audio from
the PC Audio input can be heard.
No: When viewing the PC input, there will be no
audio.
Note: Because the PC and HDMI-1 inputs
share the same set of analog audio inputs,
the PC Audio menu setting influences the
HDMI 1 Audio menu setting. If PC Audio
is set to “No,” the HDMI 1 Audio setting
changes to “Auto.” If PC Audio is set to
“Yes,” the HDMI 1 Audio setting is set to
“Digital” and is grayed out in the menu.
(Also see item 7 on page 12 and “Setting the
HDMI™ Audio mode” on page 32.)
Setting the sleep timer
You can set the sleep timer to turn off the TV after a
set length of time (maximum of 180 minutes).
To set the sleep timer using the remote control:
Press
on the remote control to set the length of
time until the TV turns off. Repeatedly press
to increase the time in 10-minute increments, or
press  or  to increase or decrease the time in
10-minute increments, to a maximum of 180 minutes.
To set the sleep timer using the on-screen
menus:
50
1無Press and open the Setup menu.
2無Highlight Sleep Timer and press .
3無Press the Number buttons to enter the length of
time in 10-minute increments.
4無Highlight Done and press
.
Note: When a power failure occurs, the
sleep timer setting may be cleared.
To display the remaining sleep time:
Press
.
Note: A message will display on-screen when
there is one minute remaining on the sleep timer.
To cancel the sleep timer:
Repeatedly press
until it is set to 0 minute.
Using REGZA-LINK®
This is a new feature that uses CEC technology
and allows you to control Toshiba REGZA-LINK
compatible devices from the TV remote via HDMI
connection ( page 17).
When the Enable REGZA-LINK in the REGZALINK setup menu ( page 51) is set to On, the
following REGZA-LINK functions will be enabled.
REGZA-LINK® playback device (DVD
player, etc.) control
With your TV’s remote control, or using the REGZALINK Player Control menu, you can control the
connected REGZA-LINK playback device you are
watching.
Available remote control key functions:
Before using the following key functions, first set the
MODE SELECT switch on the remote control to TV.
Button
Description
Begins playback.
Stops playback.
Pauses the picture during play or record
mode.
Skips forward.
Skips backward.
Fast-forwards.
Rewinds/reverses.
Chapter 6: Using the TV’s features
pqtu
VOLUME and MUTE controls of Audio
Receiver
Navigate contents menu, etc.
Enters contents menu, etc.
Returns to the previous menu.
Note: These functions depend on the devices
connected.
REGZA-LINK® Player Control menu
functions:
1無Press and open the Preferences menu.
2無 Highlight REGZA-LINK Player Control and press
.
With your TV’s remote control, you can adjust or
mute the sound volume of the Audio Receiver. First,
set the MODE SELECT switch on the remote control
to TV.
•
adjust the volume level.
•
turns off the sound.
Note:
••To use this function:
−− Set Speaker Preference to Audio Receiver in
the REGZA-LINK Setup menu.
−− Confirm that a connected REGZA-LINK device
(such as DVD player, etc) is selected for the
Audio Receiver input source.
3無Press p or q to select the item you want to
control and press
.
••You can also use this function when the audio
receiver is connected to the TV’s DIGITAL
AUDIO OUT terminal (not HDMI connection).
In this case, select a digital audio input mode
on the Audio Receiver.
••These functions depend on the device
connected.
Item
Description
Other REGZA-LINK® functions
Power
Turns the select device on and off.
Top Menu
Accesses the top menu of a DVD.
Menu
Accesses the menu of a DVD.
When the Enable REGZA-LINK and each item in the
REGZA-LINK Setup menu are set to On, the following
functions will be enabled.
Contents
Menu
Accesses the contents list when you press
. At this time, the REGZA-LINK Player
Control menu will disappear.
Note:
•These functions depend on the devices that are
connected.
•The REGZA-LINK Player Control item will be
grayed out in the following conditions:
−−A non-HDMI input is currently selected.
−−The Enable REGZA-LINK item is set to Off.
−−The connected CEC device is not a
playback or recording device.
Item
Description
TV Auto
Input Switch
If a connected HDMI device starts
playing video or audio, the TV
will automatically switch to the
appropriate HDMI input.
TV Auto
Power
If a REGZA-LINK device is turned
on, the TV turns on automatically.
Device Auto
Standby
If the TV is turned off the TV will
send a message to turn off all of the
REGZA-LINK devices connected to
the TV.
Speaker
Preference
From this item, you can set your
audio output preference to the
TV speakers or the audio receiver
speakers. When this item is set to
Audio Receiver, the TV remote
can be used to adjust or mute the
volume of the audio. This item will
be grayed out unless a REGZALINK compatible audio receiver is
connected.
REGZA-LINK input source selection
®
If a REGZA-LINK device with HDMI switching
capability (e.g. Audio Receiver) is connected to
the HDMI input, you can select another REGZALINK device that is connected to the master HDMI
device using the TV’s INPUT button. See page 34 for
details.
(continued)
51
Chapter 6: Using the TV’s features
Note: When you turn on the Audio Receiver,
change its input source, or adjust the sound
volume, the sound will be output from the audio
receiver’s speakers even if TV Speakers has
been selected. Turn the TV off and on again to
output the sound from the TV speakers.
To set the REGZA-LINK® Setup:
1無From the Setup menu, highlight REGZA-LINK
Setup and press
.
2無Press p or q to highlight Enable REGZA-LINK.
3無Press t or u to select On.
Note: If you select Enable REGZA-LINK Off, the
other items will be grayed out.
4無Press p or q to highlight the REGZA-LINK Setup
item you want to use, and press t or u to select
On or desired mode.
•TV Auto Input Switch: On/Off
•TV Auto Power: On/Off
•Device Auto Standby: On/Off
• Speaker Preference: TV Speakers/Audio Receiver
5無To save the new settings, highlight Done and press
. To revert to the factory defaults, highlight
Reset and press
.
Displaying TV status information
To display TV status information using
RECALL:
Press
on the remote control.
The following information will display (if applicable):
•Current input (ANT/CABLE, VIDEO 1, etc.)
• If ANT/CABLE is the current input, either “CABLE”
(for cable TV) or “ANT” (for over-the-air broadcasts).
• Channel number (if in ANT/CABLE mode)
• Channel label (if set)
• Digital signal strength indicator (bar graph in lower
right corner of box; for ATSC signal only)
• Stereo, Mono or SAP audio status (when HDMI input
mode, Dolby Digital or PCM)
• Video resolution
• Aspect ratio of incoming video signal (4:3 or 16:9)
• V-Chip rating status
• Game Timer (if set)
52
To close the RECALL screen:
Press
again.
To display TV status information using INFO:
Press
on the remote control.
The following additional information will display for
off air digital channels (if applicable):
• Title
• Duration
•Detailed description
Note: The location of the banner can be moved
to the top or bottom of the screen by pressing 
or  while the RECALL or INFO display is onscreen.
Understanding the auto power off
feature
The TV will automatically turn itself off after
approximately 15 minutes if it is tuned to a vacant
channel or a station that completes its broadcast for the
day. This feature functions in ANT/CABLE mode only.
Understanding the last mode
memory feature
If the power is cut off while you are viewing the
TV, the Last Mode Memory feature automatically
turns on the TV when the power is resupplied.
Note: If it’s possible, and you will be away
from the TV for an extended period of time you
should unplug the power cord.
Chapter 7: Using the TV’s advanced features
4無To save the new settings, highlight Done and
Using the advanced picture
settings features
press
.
To revert the factory defaults, highlight Reset
and press
.
Note: If you select one of the factory-set
picture modes (Sports, Standard, Movie
or PC) and then change the static gamma
setting, the picture mode automatically
changes to Preference.
Using dynamic contrast
When dynamic contrast is set to On, the TV will
detect changes in the picture quality that affect
the appearance of your contrast settings and then
automatically adjust the video.
Selecting the color temperature
To select dynamic contrast preferences:
1無Press and open the Video menu.
2無Highlight Picture Settings and press
You can change the quality of the picture by selecting
from three preset color temperatures (Cool, Medium,
and Warm), as described below.
.
3無Highlight Advanced Picture Settings and press .
4無In the Dynamic Contrast field, select either Off or On.
5無To save the new settings, highlight Done and
press
.
To revert to the factory defaults, highlight Reset
and press
.
Using the static gamma feature
The static gamma feature allows you to adjust the
levels of black in the picture.
blueish
Medium
neutral
Warm
reddish
To select the color temperature:
1無Press and open the Video menu.
2無Highlight Picture Settings and press .
3無Highlight Advanced Picture Settings and press
4無Highlight Color Temperature and press .
5無In the Color Temperature field, press  or  to
select the mode you prefer (Cool, Medium, or Warm).
6無Press  or  to select either B Drive or G Drive,
and then press  or  to adjust the settings.
• B Drive:  makes the picture blueish.
• G Drive:  makes the picture greenish.
Note: The B Drive and G Drive settings
are connected to the Color Temperature
settings and will change based on which
setting is selected in step 5 above.
To adjust the static gamma settings:
• In the Static Gamma field, press  or  to
Picture Quality
Cool
.
Note: If you select one of the factory-set
picture modes (Sports, Standard, Movie, or
PC) and then change the dynamic contrast
setting, the picture mode automatically
changes to Preference.
1無Press and open the Video menu.
2無Highlight Picture Settings and press .
3無Highlight Advanced Picture Settings and press
Mode
7無To save the new settings, highlight Done and
.
adjust the static gamma.
The adjustment range is within ±5 from center.
• If the setting is moved in the minus direction,
the detail of black colors will be decreased.
• If the setting is moved in the plus direction, the
detail of black colors will be increased.
press
.
To revert to the factory defaults, highlight Reset
and press
.
Note: If you select one of the factory-set
picture modes (Sports, Standard, Movie, or
PC) and then change the color temperature
mode, the picture mode automatically
changes to Preference.
53
Chapter 7: Using the TV’s advanced features
Using CableClear® digital noise
reduction
The CableClear® digital noise reduction feature
allows you to reduce visible interference in your
TV picture. This may be useful when receiving a
broadcast with a weak signal (especially a Cable
channel) or playing a noisy video cassette or disc.
To change the CableClear settings:
1無Press
and open the Video menu, highlight
Noise Reduction and press
.
2無In the CableClear field, select your desired setting.
Note:
•• If the current input is ANT/CABLE, VIDEO
1, or VIDEO 2, the menu will display the
text “CableClear.” The available selections
are Off, Low, Middle, and High.
•• If the current input is ColorStream HD1,
ColorStream HD2, HDMI 1, HDMI 2
or HDMI 3, the menu will display the
text “DNR.” The available selections
are Off, Low, Middle, and High. Low,
Middle, and High will reduce the noise in
varying degrees, from lowest to highest,
respectively.
3無To save the new settings, highlight Done and
press
.
To revert to the factory defaults, highlight Reset
and press
.
Using MPEG noise reduction
The MPEG noise reduction feature allows you
to reduce visible interference caused by MPEG
compression. Choices for MPEG noise reduction
are Off, Low, Middle, and High. Off is automatically
selected when this feature is disabled (“grayed out”).
To select the MPEG noise reduction level:
1無Press and open the Video menu.
2無Highlight Noise Reduction and press .
3無Press  or  to highlight the MPEG Noise
Reduction field, and then press  or  to select
either Off, Low, Middle or High.
4無To save the new settings, highlight Done and
press
.
To revert to the factory defaults, highlight Reset
and press
.
54
Using the Game Mode feature
You can use the Game Mode feature for shorter
frame delays when playing a video game requiring
split-second timing between the on-screen display
and input from the controller (such as music creation
and high-action games).
This feature is more effective for 480i and 1080i input
signals.
Note: To use the Game Mode feature, the
current video input must be Video 1, Video 2,
ColorStream HD1, ColorStream HD2, HDMI
1, HDMI 2 or HDMI 3. The Game Mode cannot
be turned on when any other video input is
selected.
To turn on Game Mode:
1無Press and open the Video menu.
2無Press  or  to highlight the Game Mode and
then press .
3無Press  or  to select On and then press
.
To turn off Game Mode:
Select Off in step 2 above, change the video input, or
turn the TV off and then on again.
Note: You can change the video input by
pressing
on the remote control ( page
34).
Chapter 7: Using the TV’s advanced features
Using the advanced audio
settings features
Using the QSound® sound feature
QSound® is the original name for a positional threedimensional (3D) sound processing algorithm from
QSound Labs that creates 3D audio effects from
multiple monophonic sources and sums the outputs
to two channels for presentation over regular stereo
speakers.
To adjust the QSound® settings:
1無Put the TV in STEREO mode ( “Selecting
stereo/SAP broadcasts” on page 42).
2無Press and open the Audio menu.
3無Highlight Advanced Audio Settings and press
4無Press  or  to highlight the QSound feature,
.
and then press  or  to turn the QSound effect
On or Off.
5無To save the new settings, highlight Done and
press
.
To revert to the factory defaults, highlight Reset
and press
.
Note: If the broadcast is monaural, the
QSound effect will not work.
55
Chapter 8: Troubleshooting
General troubleshooting
Before calling a service technician, please check this
chapter for a possible cause of the problem and some
solutions you can try.
Black box on-screen
•• The closed caption feature is set to one of the Text
modes (T1, T2, T3, or T4). Set the closed caption
feature to Off ( page 42).
TV stops responding to controls
•• If the TV stops responding to the controls on
the remote control or TV control panel and you
cannot turn off the TV, press and hold the POWER
button on the TV control panel for 5 or more
seconds to reset the TV.
Other problems
•• If your TV’s problem is not addressed in this
Troubleshooting section or the recommended
solution has not worked, use the Restore Factory
Defaults procedure ( page 33).
TV will not turn on
•• Make sure the power cord is plugged in, and then
press
.
•• The remote control batteries may be dead.
Replace the batteries or try the control panel
buttons.
Picture problems
General picture problems
•• Check the antenna/cable connections ( Chapter
2).
•• Press
••
••
••
••
••
on the remote control or TV and
select a valid video input source ( page 34).
If no device is connected to a particular input
on the TV, no picture will display when you
select that particular input source. For device
connection details, see Chapter 2.
Antenna reception may be poor. Use a highly
directional outdoor antenna (if applicable).
The station may have broadcast difficulties. Try
another channel.
Adjust the picture qualities ( page 42).
If you are using a VCR, make sure
on the
remote control is set correctly ( page 22).
Do not connect both a standard video cable and
an S-video cable to the VIDEO 1 input at the same
time ( page 14).
56
Noisy picture
•• If you are watching an analog channel (off-
air broadcast or Cable TV), you can set the
CableClear® feature to reduce visible interference
in the TV picture ( page 54).
Video Input Selection problems
•• If the Input Selection window does not appear
when you press
on the remote control or
TV, press
a second time, which will change
to the next video input source and display the
Input Selection window.
Cannot view external signals or channel
3 or 4
•• If you cannot view signals from external devices
connected to VIDEO 1, VIDEO 2, ColorStream®
HDMI 1, HDMI 2, HDMI 3, PC, or from channels
3 or 4, make sure the Input Lock is set to Off (
page 48).
Poor color or no color
•• The station may have broadcast difficulties. Try
another channel.
•• Adjust the Tint and/or Color ( page 42).
Poor composite or S-video picture
•• If the TV is connected to an external A/V device
(e.g., DVD player, video game system, set-top
box, etc.) try using a ColorStream or HDMI video
connection instead.
Picture and sound are out of sync
•• As with all products that contain a digital display,
in rare instances, when viewing certain content
(e.g.. television broadcasts, video games, DVDs),
you may notice that the sound and picture are
slightly out of sync. This phenomenon can be
caused by various factors including, without
limitation, video processing within the TV, video
processing in an attached gaming system, and
video processing or different compression rates
used by broadcasters in their programming. You
may want to try one or more of the following
suggestions, which may help to reduce the effect
of this phenomenon:
–– If the TV is connected to an A/V receiver that
has a programmable audio delay feature, use
this feature to help synchronize the sound to
the picture.
–– If you notice this phenomenon only on
certain TV channels, please contact your
local broadcast, cable, or satellite provider to
inform them of this issue.
Chapter 8: Troubleshooting
Sound problems
•• Check the antenna/cable connections ( Chapter
••
••
••
••
••
2).
The station may have broadcast difficulties. Try
another channel.
The sound may be muted. Press VOLUME.
If you hear no sound, try setting the MTS feature
to Stereo mode ( page 44).
If you are not receiving a second audio program
from a known SAP source, make sure the MTS
feature is set to SAP mode ( page 44).
If you hear audio that seems “incorrect” for the
program you are watching (such as music or a
foreign language), the SAP mode may be on. Set
the MTS feature to Stereo mode ( page 44).
Remote control problems
•• Make sure the remote control is set to the correct
device mode ( page 21).
•• Remove all obstructions between the remote
control and the TV.
•• The remote control batteries may be dead.
Replace the batteries ( page 20).
•• Your TV remote control may not operate
certain features on your external device. Refer
to the owner’s manual for your other device
to determine its available features. If your TV
remote control does not operate a specific feature
on another device, use the remote control that
came with the device ( pages 22–26).
•• If the TV still does not act as expected, use the
Reset Factory Defaults procedure ( page 33).
Channel tuning problems
•• Make sure the remote control is set to the correct
device mode ( page 21).
•• The channel may have been erased from the
channel memory by the Channel Add/Delete
feature. Add the channel to the channel memory
( page 30).
•• The channel may be blocked by the Channels
Block feature. Unblock the channel ( page 47).
•• If you are unable to tune digital channels, check
the antenna configuration ( page 29). If you
are still unable to tune digital channels, clear all
channels from the channel list ( page 31) and
reprogram channels into the channel memory
( page 30). If you are still unable to tune
digital channels, use the Reset Factory Defaults
procedure ( page 33). Also see “TV stops
responding to controls” and “Other problems”
( page 56).
Closed caption problems
•• If the program or video you selected is not
closed-captioned, no captions will display (
page 42).
•• If text is not available, a black rectangle may
appear. If this happens, turn off the closed
caption feature ( page 42).
•• A closed-caption signal may not display
correctly in the following situations: a) when
a videotape has been dubbed; b) when the
signal reception is weak; or c) when the signal
reception is nonstandard ( page 42).
Rating blocking (V-Chip) problems
•• If you forget your PIN code: While the PIN
code entering screen is displayed, press
four times within 5 seconds. The PIN code you
previously stored will be cleared ( page 45).
No REGZA-LINK operation
•• The REGZA-LINK feature is available for
Toshiba REGZA-LINK compatible devices.
•• Make sure the HDMI cables with the HDMI
Logo (
) are used.
•• When the connected REGZA-LINK device
does not work correctly after you have changed
settings of the device, turn off your TV and
unplug the power cord, then plug and turn on
again.
•• If several devices are connected, REGZA-LINK
feature may not operate properly.
•• Read the instruction manual furnished with the
connected REGZA-LINK device.
HDMI problems
For HDMI cables
•• Make sure to use cables with the HDMI Logo
(
) ( page 13).
For Legacy HDMI source
•• Some legacy HDMI sources may not work
properly with the latest HDMI TV products, due
to new standard adoption.
57
Chapter 9: Appendix
Specifications
Note:
•• This model complies with the
specifications listed below.
•• Designs and specifications are subject to
change without notice.
•• This model may not be compatible with
features and/or specifications that may be
added in the future.
Television System
NTSC standard
ATSC standard (8VSB)
Digital Cable (64 QAM, 256 QAM; in-the-clear,
unencrypted)
Channel Coverage
VHF: 2 through 13
UHF: 14 through 69
Cable TV:
Mid band (A-8 through A-1, A through I)
Super band (J through W)
Hyper band (AA through ZZ, AAA, BBB)
Ultra band (65 through 94, 100 through 135)
Power Source: 120 V AC, 60 Hz
Power Maximum Current
32RV525RZ/32RV52RZ: 1.85 A
37RV525RZ/37RV52RZ: 1.80 A
40RV525R/40RV52R: 2.75 A
40RV525RZ/40RV52RZ: 2.75 A
46RV525R/46RV525RZ : 2.95 A
Power Consumption
32RV525RZ/32RV52RZ: 0.6 W in standby mode
37RV525RZ/37RV52RZ: 0.6 W in standby mode
40RV525R/40RV52R: 0.6 W in standby mode
40RV525RZ/40RV52RZ:0.6 W in standby mode
46RV525R/46RV525RZ: 0.6 W in standby mode
Audio Power:
32RV525RZ/32RV52RZ: 10 W + 10 W
37RV525RZ/37RV52RZ: 10 W + 10 W
40RV525R/40RV52R: 10 W + 10 W
40RV525RZ/40RV52RZ: 10 W + 10 W
46RV525R/46RV525RZ: 10 W + 10 W
Speaker Type: Two 1-5/8 × 7-7/8 inches (4 × 20 cm)
Video/Audio Terminals
S-VIDEO INPUT:
Y: 1 V(p-p), 75 ohm, negative sync.
C: 0.286 V(p-p) (burst signal), 75 ohm
VIDEO/AUDIO INPUT:
VIDEO: 1 V(p-p), 75 ohm, negative sync.
AUDIO: 150 mV(rms) (30% modulation
equivalent, 22 k ohm or greater)
ColorStream® (component video) HD INPUT:
VIDEO:Y: 1V(p-p), 75 ohm
PR: 0.7 V(p-p), 75 ohm
PB: 0.7 V(p-p), 75 ohm
Suggested formats: 1080i, 720p,
480p, 480i
AUDIO: 150 mV(rms), 22 k ohm or greater
HDMI™ INPUT:
HDMI compliant (type A connector)
HDCP compliant
Audio Lip Sync supported
Suggested formats: See table on the next page.
HDMI Audio: 2-channel Linear-PCM;
32/44.1/48 kHz
sampling frequency; 16/20/24
bits per sample
DIGITAL AUDIO OUTPUT:
Optical type
PC INPUT:
15-Pin D-sub Analog RGB
Dimensions
32RV525RZ/32RV52RZ:
Width: 2’7-5/8 inches (804.6 mm)
Height: 1’10-7/8 inches (580.4 mm)
Depth: 9-1/8 inches (232.4 mm)
37RV525RZ/37RV52RZ:
Width: 3’-1/4 inches (921.5 mm)
Height: 2’1-5/8 inches (649.6 mm)
Depth: 10-7/8 inches (276.3 mm)
40RV525R/40RV52R/40RV525RZ/40RV52RZ:
Width: 3’3-1/4 inches (996.6 mm)
Height: 2’2-7/8 inches (683.3mm)
Depth: 10-7/8 inches (276mm)
46RV525R/46RV525RZ:
Width: 3’8-3/8 inches (1127.5mm)
Height: 2’6 inches (761.1 mm)
Depth: 1’-3/4 inches (325.3 mm)
Mass (Weight)
32RV525RZ/32RV52RZ: 27.2 lbs (12.3 kg)
37RV525RZ/37RV52RZ: 34.4 lbs (15.6 kg)
40RV525R/40RV52R: 39.3 lbs (17.8 kg)
40RV525RZ/40RV52RZ:39.3 lbs (17.8 kg)
46RV525R/46RV525RZ: 50.2 lbs (22.8 kg)
Operating conditions
Temperature: 32ºF - 95ºF (0ºC - 35ºC)
Humidity: 20 - 80% (no moisture condensation)
Supplied Accessories
•Remote control with two size “AAA” batteries
•Owner’s manual (this book)
•Cleaning cloth
58
Chapter 9: Appendix
Acceptable signal formats for PC IN and HDMI terminals
PC IN signal formats
Note: Depending on the connected PC, the following status may occur; incorrect display, false format
detection, picture position failure, blur, or judder. But this is not a malfunction of your TV.
Format
Resolution
V. Frequency
H. Frequency
Pixel Clock Frequency
VGA
640 × 400
70.090Hz
31.470kHz
25.180MHz
VGA
640 × 480
59.940Hz
31.469kHz
25.175MHz
SVGA
800 × 600
60.317Hz
37.879kHz
40.000MHz
XGA
1024 × 768
60.004Hz
48.363kHz
65.000MHz
WXGA
1280 × 768
59.870Hz
47.776kHz
79.500MHz
1360 × 768
60.015Hz
47.712kHz
85.500MHz
1280 × 1024
60.020Hz
63.981kHz
108.000MHz
SXGA
HDMI signal formats
Format
Resolution
V. Frequency
H. Frequency
Pixel Clock Frequency
VGA
640 × 480
59.940Hz
31.469kHz
25.175MHz
SVGA
800 × 600
60.317Hz
37.879kHz
40.000MHz
XGA
1024 × 768
60.004Hz
48.363kHz
65.000MHz
WXGA
1280 × 768
59.870Hz
47.776kHz
79.500MHz
1360 × 768
60.015Hz
47.712kHz
85.500MHz
SXGA
1280 × 1024
60.020Hz
63.981kHz
108.000MHz
480i
720 × 480i
59.940Hz
15.734kHz
27.000MHz
480p
720 × 480p
59.940Hz
31.469kHz
27.000MHz
720p
1280 × 720p
60.000Hz
45.000kHz
74.250MHz
1080i
1920 × 1080i
60.000Hz
33.750kHz
74.250MHz
1080p
1920 × 1080p
24.000Hz
27.000kHz
74.250MHz
1080p
1920 × 1080p
60.000Hz
67.500kHz
148.500MHz
59
Chapter 9: Appendix
Limited United States Warranty
for LCD Televisions 26” and Larger
Toshiba America Consumer Products, L.L.C. (“TACP”)
makes the following limited warranties to original
consumers in the United States.
THESE LIMITED WARRANTIES EXTEND TO
THE ORIGINAL CONSUMER PURCHASER OR
ANY PERSON RECEIVING THIS LCD ELEVISION
AS A GIFT FROM THE ORIGINAL CONSUMER
PURCHASER AND TO NO OTHER PURCHASER OR
TRANSFEREE. LCD TELEVISIONS PURCHASED IN
THE U.S.A. AND USED ANYWHERE OUTSIDE OF
THE U.S.A., INCLUDING, WITHOUT LIMITATION,
CANADA AND MEXICO, ARE NOT COVERED BY
THESE WARRANTIES.
LCD TELEVISIONS PURCHASED ANYWHERE
OUTSIDE OF THE U.S.A., INCLUDING, WITHOUT
LIMITATION, CANADA AND MEXICO, AND USED
IN THE U.S.A., ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labor
TACP warrants this LCD Television and its parts against
defects in materials or workmanship for a period of
one (1) year after the date of original retail purchase.
DURING THIS PERIOD, TACP WILL, AT TACP’S
OPTION, REPAIR OR REPLACE A DEFECTIVE PART
WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU FOR PARTS OR LABOR. During this
period, TACP Authorized Service Station personnel will
come to your home when warranty service is required.
Depending on the type of repair required, the service
will either be performed in your home or the LCD
Television will be taken to a TACP Authorized Service
Station for repair and returned to your home at no cost
to you.
Rental Units
The warranty for LCD Television rental units begins on
the date of the first rental or thirty (30) days after the
date of shipment to the rental firm, whichever comes
first.
Limited Warranty for Commercial Units
TACP warrants LCD Televisions that are sold and
used for commercial purposes as follows: all parts are
warranted against defects in materials or workmanship
for a period of ninety (90) days after the date of original
retail purchase. DURING THIS PERIOD, TACP WILL, AT
TACP’S OPTION, REPAIR OR REPLACE A DEFECTIVE
PART WITH A NEW OR REFURBISHED PART WITHOUT
CHARGE TO YOU.
Owner’s Manual and Product Registration Card
Read this owner’s manual thoroughly before operating
this LCD Television.
Complete and mail the enclosed product registration
card or register your LCD Television online at www.tacp.
com/service as soon as possible. By registering your LCD
Television you will enable TACP to bring you new products
specifically designed to meet your needs and help us to
contact you in the unlikely event a safety notification is
required under the U.S. Consumer Product Safety Act.
Failure to complete and return the product registration card
does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must retain your original bill of sale or
provide other proof of purchase.
(2) All warranty servicing of this LCD Television must
be performed by an Authorized TACP Service
Station.
(3) The warranties from TACP are effective only if this
LCD Television is purchased and operated in the
Continental U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup,
adjustment of customer controls, and installation
or repair of antenna systems are not covered by
this warranty. Reception problems caused by
inadequate antenna systems, misaligned satellite
dishes, cable television distribution, VCRs, DVD
players/recorders, personal computer level IEEE1394 devices, and any other connected signal
source device are your responsibility.
(5) Warranties extend only to defects in materials
or workmanship as limited above, and do not
extend to any LCD Television or parts that have
been lost or discarded by you or to damage
to the LCD Television or parts caused by fires,
misuse, accident, Acts of God (such as lightning or
fluctuations in electric power), improper installation,
improper maintenance, or use in violation of
instructions furnished by TACP; use or malfunction
through simultaneous use of this LCD Television
and connected equipment; or to units that have
been modified or had the serial number removed,
altered, defaced, or rendered illegible.
How to Obtain Warranty Service
If, after following all of the operating instructions
in this manual and reviewing the section entitled
“Troubleshooting,” you find that service is needed:
(1) To find the nearest TACP Authorized Service
Station, visit
TACP’s website at www.tacp.com/service or contact
TACP’s Consumer Solution Center toll free at 1-800631-3811.
(2) You must present your original bill of sale or other
proof of purchase to the TACP Authorized Service
Station.
For additional information, visit TACP’s website:
www.tacp.com
ALL WARRANTIES IMPLIED BY THE LAW OF ANY
STATE OF THE U.S.A., INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE
EXPRESSLY LIMITED TO THE DURATION OF THE
LIMITED WARRANTIES SET FORTH ABOVE. WITH
THE EXCEPTION OF ANY ARRANTIES IMPLIED
BY THE LAW OF ANY STATE OF THE U.S.A. AS
HEREBY LIMITED, THE FOREGOING WARRANTY
IS EXCLUSIVE AND IN LIEU OF ALL OTHER
WARRANTIES, GUARANTEES, AGREEMENTS, AND
SIMILAR OBLIGATIONS OF TACP WITH RESPECT
TO THE REPAIR OR REPLACEMENT OF ANY
PARTS. IN NO EVENT SHALL TACP BE LIABLE FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, LOST PROFITS,
BUSINESS INTERRUPTION, OR MODIFICATION
OR ERASURE OF RECORDED DATA CAUSED BY
USE, MISUSE OR INABILITY TO USE THIS LCD
TELEVISION).
60
Chapter 9: Appendix
No person, agent, distributor, dealer, or company is
authorized to change, modify, or extend the terms of
these warranties in any manner whatsoever. The time
within which an action must be commenced to enforce
any obligation of TACP arising under the warranty or
under any statute or law of the United States or any
state thereof is hereby limited to ninety (90) days from
the date you discover, or should have discovered,
the defect. This limitation does not apply to implied
warranties arising under the law of any state of the U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE IN THE
U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW
LIMITATIONS ON THE DURATION OF AN IMPLIED
WARRANTY, WHEN AN ACTION MAY BE BROUGHT,
OR THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. THEREFORE,
THE ABOVE PROVISIONS MAY NOT APPLY TO YOU
UNDER SUCH CIRCUMSTANCES.
[0305]
Limited Canadian Warranty
for Toshiba Brand Flat Panel
Televisions
Toshiba of Canada Limited (“TCL”) makes the
following limited warranties to original consumers in
Canada. THESE LIMITED WARRANTIES EXTEND
TO THE ORIGINAL CONSUMER PURCHASER OR
ANY PERSON RECEIVING THIS TOSHIBA BRAND
FLAT PANEL TELEVISION (the “TELEVISION(S)” or
“Television(s)”) AS A GIFT FROM THE ORIGINAL
CONSUMER PURCHASER AND TO NO OTHER
PURCHASER OR TRANSFEREE.
TELEVISIONS PURCHASED IN CANADA, AND USED
ANYWHERE OUTSIDE OF CANADA INCLUDING,
WITHOUT LIMITATION, THE UNITED STATES
AND MEXICO, ARE NOT COVERED BY THESE
WARRANTIES.
TELEVISIONS PURCHASED ANYWHERE OUTSIDE
OF CANADA, INCLUDING, WITHOUT LIMITATION,
THE UNITED STATES AND MEXICO, AND USED
IN CANADA, ARE NOT COVERED BY THESE
WARRANTIES.
Limited One (1) Year Warranty on Parts and Labour
Subject to the more limited warranty if the Television is
used for any commercial or business purposes as set
out below, TCL warrants the Television and its parts
against material defects in materials or workmanship
that result in the Television failing for a period of one (1)
year after the date of original retail purchase. DURING
THIS PERIOD, TCL WILL, AT TCL’S OPTION, REPAIR
OR REPLACE A DEFECTIVE PART WITH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU
FOR PARTS OR LABOUR.
(a) FOR TELEVISIONS 32 INCHES OR LESS: YOU
MUST DELIVER THE ENTIRE TELEVISION TO
A TCL TELEVISION AUTHORIZED SERVICE
PROVIDER (“ASP”). YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES
FOR THE TELEVISION TO AND FROM THE ASP.
(b) FOR TELEVISIONS OVER 32 INCHES: During this
period, ASP personnel will come to your home
61
when warranty service is required. Depending on
the type of repair required, the service will either
be performed in your home or the Television will
be taken to an ASP for repair and returned to your
home at no cost to you. IN-HOME SERVICE ONLY
APPLIES WITHIN 100 KILOMETERS OF AN ASP.
IF YOU ARE NOT WITHIN 100 KILOMETERS
OF AN ASP, YOU MUST DELIVER THE ENTIRE
TELEVISION TO AN ASP. YOU MUST PAY FOR
ALL TRANSPORTATION AND INSURANCE
CHARGES FOR THE TELEVISION TO AND FROM
THE ASP.
Limited Warranty for Commercial Units
TCL warrants Televisions that are used for any
commercial or business purposes as follows: all parts
are warranted against material defects in materials or
workmanship that result in the Television failing for a
period of ninety (90) days after the date of original retail
purchase. DURING THIS PERIOD, TCL WILL, AT TCL’S
OPTION, REPAIR OR REPLACE THE DEFECTIVE
PART WITH A NEW OR REFURBISHED PART
WITHOUT CHARGE TO YOU.
(c) FOR TELEVISIONS 32 INCHES OR LESS: YOU
MUST DELIVER THE ENTIRE TELEVISION
TO AN ASP. YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES
FOR THE TELEVISION TO AND FROM THE ASP.
(d) FOR TELEVISIONS OVER 32 INCHES: During this
period, ASP personnel will come on-site when
warranty service is required. Depending on the
type of repair required, the service will either be
performed on-site or the Television will be taken
to an ASP for repair and returned at no cost to
you. ON-SITE SERVICE ONLY APPLIES WITHIN
100 KILOMETERS OF AN ASP. IF YOU ARE
NOT WITHIN 100 KILOMETERS OF AN ASP,
YOU MUST DELIVER THE ENTIRE TELEVISION
TO AN ASP. YOU MUST PAY FOR ALL
TRANSPORTATION AND INSURANCE CHARGES
FOR THE TELEVISION TO AND FROM THE ASP.
Rental Units
The warranty for Television rental units begins with the
date of first rental or thirty (30) days from the date of
shipment to the rental firm, whichever comes first.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDITIONS:
(1) You must provide your bill of sale or other proof of
purchase.
(2) All warranty servicing of this Television must be
performed by an ASP.
(3) The warranties from TCL are effective only if the
Television is (i) purchased as new and unopened
from TCL or from TCL’s authorized distributors,
dealers or resellers (“ADR’s”) and (ii) located/
operated in Canada.
(4) Labour charges for set installation, setup,
adjustment of customer controls, and installation
or repair of antenna systems are not covered by
these warranties. Reception problems caused by
inadequate antenna systems are your responsibility.
(5) Warranties extend only to material defects in
materials or workmanship as limited above, and do
not extend to:
a. Service, repairs or replacement made
necessary by accident, misuse, abuse,
moisture, liquids, dust, dirt, neglect, accident,
Chapter 9: Appendix
b.
c.
d.
e.
f.
g.
h.
i.
j.
damage, 24/7 applications, improper
installation, improper operation, improper
cleaning, improper maintenance, normal
wear and tear, screen burn or image retention
caused by prolonged display of static images
and/or phosphor aging, or any other external
cause or event, act or omission outside
the control of TCL, including fire, theft, acts
of God, alteration, power failures, power
surges or power shortages, lightning, other
electrical faults, or repairs, modifications or
replacements by persons other than those
authorized by TCL to service the Television;
Replacement of missing, discarded or lost
parts, the provision of retrofits, or preventive
maintenance;
Repair of damage that is cosmetic only or
does not affect the Television functionality,
such as wear and tear, scratches and dents;
Service on Toshiba-branded accessory items
(such accessory items may be covered by
their own warranty);
Service on third party products or service
made necessary by use of incompatible third
party products;
Service made necessary by the simultaneous
use of this Television and connected
equipment;
Modifications to the Television not approved in
writing by TCL, and service made necessary
by the use or installation of non-Toshiba
modifications to the Television;
Service of a Television on which the TOSHIBA
label or logo, rating label or serial number
have been defaced or removed;
On-site service and repair of the Television;
and
Damage to the Television caused by failure
to follow the specifications, User manuals or
guides as to usage and/or storage.
Disclaimer and Limitation of Remedy
TO THE EXTENT NOT PRECLUDED BY LAW, ALL
OTHER EXPRESS AND IMPLIED WARRANTIES,
CONDITIONS AND REPRESENTATIONS
FOR THIS TELEVISION, INCLUDING THE
IMPLIED WARRANTIES, CONDITIONS AND
REPRESENTATIONS OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
ARE HEREBY DISCLAIMED AND EXCLUDED.
IF THE APPLICABLE LAW, STATUTORY OR
OTHERWISE, PRECLUDES THE EXCLUSION
OF ANY IMPLIED WARRANTIES, CONDITIONS
AND REPRESENTATIONS THEN SUCH
IMPLIED WARRANTIES, CONDITIONS AND
REPRESENTATIONS ARE OTHERWISE LIMITED
IN DURATION TO THE TERM OF THIS EXPRESS
WRITTEN LIMITED WARRANTY. TO THE EXTENT NOT
PRECLUDED BY LAW, STATUTORY OR OTHERWISE,
THIS WRITTEN WARRANTY SUPERCEDES AND
SPECIFICALLY DISCLAIMS ANY OTHER WARRANTY,
CONDITION OR REPRESENTATION NOT STATED
IN THIS WARRANTY, WHETHER MADE BY TCL,
TOSHIBA CORPORATION, THEIR AFFILIATES, ADRs
AND ASPs AND WHETHER MADE ORALLY OR IN
WRITING (INCLUDING ANY STATEMENT IN ANY
BROCHURE, PRESS RELEASE, ANNOUNCEMENT,
ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.).
YOU MUST READ AND FOLLOW ALL SET-UP AND
USAGE INSTRUCTIONS IN THE APPLICABLE USER
GUIDES AND/OR MANUALS. IF YOU FAIL TO DO SO,
THIS TELEVISION MAY NOT FUNCTION PROPERLY
AND YOU MAY SUFFER DAMAGE. THIS WARRANTY
WILL NOT COVER ANY SERVICE THAT IS REQUIRED,
IN PART OR IN WHOLE, AS A RESULT OF ANY
FAILURE TO FOLLOW THE SET-UP AND USAGE
INSTRUCTIONS. THIS WARRANTY DOES NOT APPLY
AND SHALL BE VOID AND UNENFORCEABLE IF THE
TELEVISION IS OPENED, SERVICED, OR REPAIRED
BY PERSONS OTHER THAN THOSE AUTHORIZED BY
TCL TO SERVICE OR REPAIR THE TELEVISION.
IF THE TELEVISION FAILS TO WORK AS WARRANTED
ABOVE, YOUR SOLE AND EXCLUSIVE REMEDY
SHALL BE REPAIR OR REPLACEMENT OF THE
DEFECTIVE PART. IN NO EVENT WILL TCL, TOSHIBA
CORPORATION, THEIR AFFILIATES, ADRs OR
ASPs (THE “RELATED PARTIES”) BE LIABLE TO
YOU OR ANY THIRD PARTY FOR ANY DAMAGES,
MONEY, REIMBURSEMENT, COSTS OR EXPENSES.
THIS LIMITATION APPLIES TO DAMAGES, MONEY,
REIMBURSEMENT, COSTS OR EXPENSES OF ANY
KIND WHATSOEVER INCLUDING ANY DIRECT OR
INDIRECT DAMAGES, DAMAGE TO PROPERTY
OR ERSON, LOST PROFITS, LOST SAVINGS,
INCONVENIENCE OR OTHER SPECIAL, INCIDENTAL,
EXEMPLARY OR CONSEQUENTIAL DAMAGES,
WHETHER FOR BREACH OF WARRANTY, BREACH
OF CONTRACT, TORT (INCLUDING NEGLIGENCE),
UNDER A STATUTE OR UNDER ANY OTHER LAW OR
FORM OR ACTION, OR WHETHER ARISING OUT OF
THE USE OF OR INABILITY TO USE THE TELEVISION,
VEN IF ANY OF THE RELATED PARTIES HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
OR OF ANY CLAIM BY ANY OTHER PARTY.
No person, agent, distributor, dealer or company is
authorized to change, modify or extend the terms of
these warranties in any manner whatsoever.
62
Chapter 9: Appendix
Arbitration and Dispute Resolution
To the extent not precluded by law, any claim, dispute,
controversy or disagreement (whether for breach of
warranty, breach of contract, tort (including negligence
and negligent and/or fraudulent misrepresentation),
under a statute or under any other law or form of action)
against any of the Related Parties arising out of, or
otherwise relating to: (i) this warranty; (ii) the Television;
(iii) any oral or written representations, statements,
brochures, press releases, advertising, announcement,
point of sale display, or promotional material relating to
the Television; (iv) the relationships that result from this
warranty, (the foregoing claims, disputes controversies
and disagreements are collectively referred to as the
“Dispute”), shall be referred to and resolved by final
and binding arbitration (to the exclusion of the courts).
To the extent not precluded by law, you agree to waive
any right that you may have to commence or participate
in any representative or class proceeding against the
Related Parties relating to any Dispute. If and where
applicable and to the extent not precluded by law, you
further agree to opt out of any such representative or
class proceedings. Arbitration of any Dispute will be
conducted in the forum and in the manner as agreed
to between you and TCL. Failing such agreement, the
arbitration will be conducted by one arbitrator pursuant
to the laws and rules relating to arbitration generally in
force in the jurisdiction in which you reside at the time
that the Dispute arises. To the extent not precluded by
law, no claim, dispute, controversy or disagreement of
any other person may be joined or combined with any
Dispute by you, without the prior written consent of TCL.
Critical Applications
The Television you have purchased is not designed
for any “critical applications.” “Critical applications”
means life support systems, medical applications,
connections to implanted medical devices, commercial
transportation, nuclear facilities or systems or any other
applications where Television failure could lead to
injury to persons or loss of life or catastrophic property
damage.
IF THE CUSTOMER USES THE TELEVISION IN ANY
CRITICAL APPLICATION, THE CUSTOMER - AND
NOT TCL, ITS AFFILIATES, ADRs OR ASPs - ASSUME
SOLE AND FULL RESPONSIBILITY FOR SUCH USE.
TCL RESERVES THE RIGHT TO REFUSE TO SERVICE
ANY TELEVISION USED IN A CRITICAL APPLICATION.
TCL, ITS AFFILIATES, ADRs AND ASPs HEREBY
DISCLAIM ANY AND ALL LIABILITY, DAMAGES AND
CONSEQUENCES ARISING OUT OF THE SERVICE
OR REFUSAL TO SERVICE SUCH TELEVISION
AND FURTHER DISCLAIM ANY AND ALL LIABILITY,
CONSEQUENCES AND DAMAGES THAT MAY ARISE
OR RESULT FROM THE USE OF THE TELEVISION IN
ANY CRITICAL APPLICATIONS.
General Provisions
If and to the extent that any provision of this
limited warranty should generally be found to be
unenforceable, the unenforceable provision shall be
severed from the warranty and deemed not to form
part of the warranty. The remaining provisions of this
warranty shall be and remain valid and enforceable.
If and to the extent that any provision of this limited
warranty as it relates to any of the Related Parties is
found to be invalid or unenforceable in respect of that
party (the “Excluded Party”), the Excluded Party shall be
deemed to be severed or excluded from the provision,
and the provision shall remain valid, enforceable and
63
applicable in respect of the other or remaining Related
Parties.
To the extent permitted by law, this limited warranty shall
be governed and construed in accordance with the
laws of Ontario.
If there is any inconsistency between this limited
warranty, on the one hand, and any statement in the
packaging of the Television or in any other document
enclosed with, or used in the context of the promotion or
sale of, the Television, on the other hand, the provisions
of this limited warranty shall prevail.
How to Obtain Warranty Services
If, after following all of the operating instructions in this
manual and checking the “Troubleshooting” section,
you find that service is needed:
(1) To find the nearest ASP, visit TCL’s web site at www.
toshiba.ca, or call toll free 1-800-268-3404
(2) Present your bill of sale or other proof of purchase
to the ASP.
For additional information, visit TCL’s website at www.
toshiba.ca
A copy of the GPL source code in this product
may be obtained by contacting Toshiba Consumer
Solutions at (800)631-3811. There will be a charge to
cover the costs of providing the source code.
TOSHIBA AMERICA CONSUMER
PRODUCTS, L.L.C.
Corporate Headquarters: 82 TOTOWA ROAD, WAYNE, NJ 07470, U.S.A.
NATIONAL SERVICE DIVISION: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A.
TOSHIBA OF CANADA LTD.
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA
– TEL: (905) 470-5400
SERVICE CENTERS:
TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA
– TEL: (905) 470- 5400
MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA
– TEL: (514) 390-7766
VANCOUVER: 6932 GREENWOOD STREET, BURNABY, B.C., V5A 1X8, CANADA
– TEL: (604) 303-2500
CableClear, ColorStream, GameTimer, and TheaterWide are registered trademarks of Toshiba
America Consumer Products, L.L.C.
Channel Browser, DynaLight, and SurfLock are trademarks of Toshiba America Consumer
Products, L.L.C.
REGZA-LINK is a registered trademark of Toshiba Corporation.
PRINTED IN CHINA
Download PDF

advertising