ABC Office 802CC Paper Shredder User Manual

802CC
852CC
The Shredder Company
Schleicher International
POSTFACH 1420
D-88672 MARKDORF/BODENSEE - GERMANY
Tel.: +49(0)7544/60-0
Fax: +49(0)7544/60-248
E-mail: vertrieb@schleicher.de
http//www.schleicher.de
Typ/Type/Type/Tipo:
648 / 649
Serie/Series/Série/Serie:
648 / 649
Vor der Inbetriebnahme die Bedienungsanleitung durchlesen!
Before operating, please read the Operating Instructions!
Veuillez lire le mode d’emploi avant la mise en service!
Voor de inbedrijfstelling de gebruiksaanwijzing doorlezen!
Leer las instrucciones de uso antes de la puesta en servicio!
Antes de pôr a máquina em funcionamento leia as instruções de operação!
Prima della messa in funzione leggere attentamente le istruzioni!
Bedienungsanleitung
Operating instructions
Instructions d’opération
Gebruiksaanwijzing
Instrucciones de uso
Instruções de Operação
Istruzioni per l’uso
Schaltplan / Wiring Diagram / Plan de montage / Schakelschema
Diagrama eléctrico / Esquema electrico / Schema Elettrico
(Seite 2-4)
D
(page 5-7)
GB
(page 8-10)
F
(pagina 11-13)
NL
(página 14-16)
E
(página 17-19)
P
(pagina 20-22)
I
(Seite / page / pagina
página / pagina 23-24)
1-800-658-8788 - www.abcoffice.com
802CC
852CC
GB
Schleicher International
IMPORTANT SAFETY NOTES
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< Keep all loose articles of clothing,
ties, jewelery, long hair or other
loose objects away from opening,
injury may result!
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.).
<< Never insert fingers into opening.
Serious injury may result!
<< Keep children away from the machine.
This machine’s design and safety concept
are based on adult dimensions (inlet guide,
safety cut-off switches, etc.) to ensure that it
can be operated safely by adults only.
STOP
<< In case of danger switch the machine
off with the mains switch, or with the
emergency switch, or unplug the
machine.
<< Always unplug the machine from the
mains power supply before opening
the machine.
<< Repairs may only be performed by trained
personnel.
INITIAL START UP
APPLICATION:
The INTIMUS 802CC/852CC shredder is used in
all areas where large quantities of printed material
need to be shredded.
The machine (model 852CC) can shred cardboard
and crumpled paper as easily as it shreds smooth
paper.
CAUTION: The shredder should only
be fed with paper or cardboard!
Shredding other data carriers can cause
injury(e.g. by splintering of hard materials)
or may damage the shredder (e.g.
destruction of the cutting system).
INSTALLATION REQUIREMENTS:
Note: Be certain that three phase current is
available at the point of installation (see
TECHNICAL DATA for information concerning
required pre-fusing of the electrical outlet).
- Unpack and set machine upright.
- Put the collecting bag into the sliding frame (see
description „EMPTYING THE COLLECTING
BAG“)
- Plug in the machine.
The air vents in the housing are
necessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 40°C!
CHECKING THE RUNNING DIRECTION:
1. Move the main switch (1) (fig. 1) to position „1“.
2. Press the „forward“ button (2) (fig. 2). The
cutting system starts running.
3. Check that the cutting system is running in the
correct direction and correct the phase relation
of the power plug if necessary.
Correcting the phase relation of the
power plug may only be carried out
by a qualified electrician!
Now that everything has been correctly assembled
and connected, you can proceed to operating the
machine.
POWER SUPPLY CONNECTION:
a) The maximum value for loop impedance at the
mains connection point is 0.5 Ohms.
b) The conductor cross-section of the power supply
line should be of a magnitude so as to cause a
15% voltage drop in the case of a machine
blockage (inhibit current = 6 x nominal current).
I
S
MAINS SWITCH
1
4
fig. 1
3
2
5
6
7
fig. 2
5
1-800-658-8788 - www.abcoffice.com
802CC
852CC
GB
Schleicher International
OPERATION
OPERATING FUNCTIONS (Figs. 1, 2 and 4):
1 = Mains switch (Emergency-stop) (fig. 1)
This switch turns the machine either on
(position „1“) or off (position „0“).
2 = „Cutting system forward“
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
3 = „Cutting system stop“
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse“
pushbutton (fig. 2)
Pressing this button starts the cutting system
in reverse.
5 = Pilot lamp (fig. 2)
a) „ready“
Continously lights when the mains switch
(1) is operated.
b) „motor protection“
Flashes when the motor is overloaded.
While the motor is cooling down, the
machine cannot be switched on to „forward“
run.
6 = Pilot lamp „paper jam“ (fig. 2)
Lights when too much paper is fed to the
cutters (see description „AUTOMATIC
RESPONSE IN CASE OF OVERLOADING“).
7 = Pilot lamp (fig. 2)
a) „door open“/„hopper open“
Lights when the door is not closed or when
the hopper is open. The machine then
switches off automatically and it cannot be
started as long as the door is open or the
hopper is open.
b) „collecting bag full“ (fig. 2)
Lights as soon as the collecting bag is full
and needs to be emptied. At the same time
the machine switches off automatically.
8 = Light barrier (forward operation) (fig. 4)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
OPERATING THE MACHINE:
To start, switch on the unit by operating the mains
switch (1) (fig. 1). The pilot lamp marked „ready for
operation“ (5), as well as the red stop-button „S“
(3) (fig. 2) will light to indicate that the machine is
ready for operation.
The paper tray may not be used as a
step ladder or as a seat. Danger of
tipping over!
FEEDING CRUMPLED PAPER
(MODEL 852CC):
In order to avoid a reduction of user
safety by increasing the height of the
hopper side panels, and in order to
allow for filling the hopper while
standing on the floor, the height of the
hopper side panels is not in compliance
with EN 294:1992.
The deviation from EN 294:1992 is
identified with a yellow-black mark.
1. Fill the hopper with crumpled paper.
Note: The crumpled paper can be dropped
directly from the wastepaper basket into the
hopper of the machine. The apportioning wings
preceding the cutting mechanism ensure more
or less uniform distribution of the paper.
Attention: The wastepaper basket is no refuse
tin and should not be emptied into the machine
thoughtlessly - in no way can the machine
destroy bottles, pens, pencil sharpeners etc.
2. Press the pushbutton switch „forward“ (2) (fig.
2). The cutting system runs and begins to shred
the paper.
Note: Do not feed any smooth paper until the
crumpled paper is completely shredded.
3. To switch the machine off press the red stopbutton (3) (fig. 2).
Never feed the shredder with a quantity
of paper exceeding the maximum
indicated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC
RESPONSE
IN
CASE
OF
OVERLOADING“.
AUTOMATIC RESPONSE
IN CASE OF „OVERLOADING“:
In case you accidentally overload the shredder, it
will automatically alleviate the problem as follows:
1. The cutting system becomes jammed. The pilot
lamp (6) (fig. 2) lights up.
2. The cutting system runs briefly in reverse,
thereby freeing the material to be shredded.
3. The cutting system automatically switches back
to forward mode.
The machine repeats this process until all the
material has been shredded satisfactorily.
EMPTYING THE COLLECTING BAG (Fig. 3):
When the collecting bag is full, the machine turns
off automatically. The pilot lamp (7) (fig. 2) lights
up. Empty the collecting bag as follows:
- Open the door and take out the sliding frame
with the collecting bag.
- Remove the rubber band, take out the full bag
and dispose of contents.
- Put the empty bag from below through the
sliding frame and put the edges of the bag
approx. 10 cm over the frame outwardly.
- Fix the collecting bag with the rubber band at the
sliding frame.
- Move back the sliding frame with the collecting
bag and close door.
Note: The machine will only run with closed door!
FEEDING SMOOTH PAPER:
- Feed smooth paper through the opening at the
lower part of the hopper (model 852CC) or
through the opening of the hopper (model 802CC)
to the cutting system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
I
S
MAINS SWITCH
1
fig. 1
4
3
2
5
fig. 2
6
6
7
fig. 3
1-800-658-8788 - www.abcoffice.com
802CC
852CC
GB
Schleicher International
MAINTENANCE
CUTTING SYSTEM MAINTANANCE:
After about 2 hours of continuous operation run
the cutting system in reverse for about 30 seconds
and, at the same time, spray some of the enclosed
special oil onto the cutting system.
CLEANING THE PHOTOCELLS (8) (Fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean the
photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
ENERGY SAVING TIP:
Be certain that the machine is turned off overnight
(mains switch (1) (fig. 1) switched to „0“).
8
fig. 4
MALFUNCTION
TAKING OUT EXCESS PAPER
IN CASE OF OVERLOAD:
If the shredder has stopped due to an overload
(motor protection) take the excess paper out of
the inlet as follows:
1. Depress the reverse pushbutton (4) (fig. 2). The
material is released.
2. Lift up the hopper. The pilot lamp „door open“ or
„hopper open“ (7) (fig. 2) will light.
3. Remove the excess material by hand from the
inlet guide.
Note: In this case, there is no danger of injury
as all circuits are interrupted when the hopper
is lifted and the machine cannot be started.
MOTOR FAULT:
The machine is equipped with a thermally protected
motor. Should this motor be overloaded, it will
switch off automatically. In such case the pilot
lamp „ready“ (5) (fig. 2) flashes.
After a cooling down period of approx. 10 minutes
(depending on the room temperature) you can
restart the machine and continue shredding.
TECHNICAL DATA
Note: When the motor is overloaded, only the
forward run is cut off. To take the excess paper out
of the inlet opening, the cutting system may at any
time be switched on „reverse“.
FAULT CHECKLIST:
If the machine is not functioning properly, you
should check the following:
- is the plug conneted to the mains?
- is the mains switch (1) turned on?
- is the door closed?
- is the collecting bag full?
The bag has to be emptied.
- is the motor overloaded?
Please refer to the section headed „Motor Fault“.
- is there a phase failure?
Check the three-phase fuse at the power supply
socket, and replace if necessary.
If you still cannot isolate the fault after carrying
out all these checks, please notify our customer
service department.
Cutting width:
802CC:
852CC:
Cutting capacity:
802CC:
852CC:
Working width:
Power:
Supply voltage:
1.9x15 (cross-cut)
3.8x40 (cross-cut)
35-40 sheets (70 g/m2)
70-80 sheets (70 g/m2)
444 mm
3.9 kW
400V/50Hz
230V/50Hz
415V/50Hz
220V/60Hz
200V/50Hz
200V/60Hz
Pre-fusing:
(gl fuse, type 1 assignment)
400V-415V/50Hz:
16 A
220V-230V/50-60Hz:
25 A
200V/50-60Hz:
25 A
Width:
750 mm
Depht:
550 mm
Height:
802CC:
1275 mm
852CC:
1600 mm
Noise level:
approx. 75 dB(A)
Weight:
802CC:
approx. 185 kg
852CC:
approx. 201 kg
ACCESSORIES
Description
Order-No.
Plastic bag, 600 x 380 x 1100 x 0,6 mm
80946
Lubrication bottle, 125 ml
99943
Note: For orders of special accessories and spare parts, please contact your dealer.
7
1-800-658-8788 - www.abcoffice.com
802CC
852CC
Schleicher International
Konformitätserklärung
Certificate of Conformity
Attestation de Conformité
Bezeichnung der Maschine:
Type of machine:
Déscription de la machine:
Datenshredder
Document Shredder
Destructeur de Document
Modelle / Models / Modèles:
intimus 802CC
intimus 852CC
Typen / Types / Types:
648 / 649
Hiermit wird bestätigt, daß o. g. Geräte den Anforderungen der Maschinen-Richtlinie 89/392/EWG, sowie
der EMV-Richtlinie 89/336/EWG (Klasse B) einschließlich allen bis heute veröffentlichten Änderungen
bzw. Nachträgen entsprechen. Die o. g. Geräte entsprechen folgenden Normen bzw. Richtlinien:
We do hereby certify that the above mentioned products meet the requirements set forth in EEC-Guidelines
89/392 and EMC 89/336 (Class B) including all changes and addendums to date thereto. The above
mentioned products meet the following standards and guidelines:
Nous Vous Confirmons que les appareils cités ci-dessus correspondent aux exigences des directives 89/
392/CEE ainsi qu’ à la directive CEM 89/336/CEE (Classe B), ci-inclus toutes les modifications ainsi que
tous les suppléments publiés jusqu’à ce jour. Les appareils mentionnés correspondent aux normes citées
ci-après:
EN 292-1, Ausgabe / dated / en date du 1991
EN 294-1, Ausgabe / dated / en date du 1992
EN 60204-1, Ausgabe / dated / en date du 1993
EN 55011, Ausgabe / dated / en date du 1993
EN 61000-4-2 /-4 (IEC 1000-4-2 /-4), Ausgabe / dated / en date du 1995
ENV 50140 (IEC 1000-4-3), Ausgabe / dated / en date du 1993
November / November / Novembre 2000
POSTFACH 1420
D-88672 MARKDORF/BODENSEE - GERMANY
ppa. D. Schuster
i. A. J. Erlecke
Leiter Technik
Leiter Elektrik
Head of Technical Dpt.
Responsable Dép. Technique
Head of Electrical Dpt.
Responsable Dép. Electricité
Dieses Papier ist aus 100 % Altpapier ohne optische Aufheller hergestellt
This paper made from 100 % unbleached recycled paper
Papier recyclable à 100 %
00000 1 07/01
The Shredder Company
1-800-658-8788 - www.abcoffice.com