Abocom 56K Network Router User Manual

Internal
Fax Modem 56K
Quick Installation Guide
FCC REGULATORY STATEMENTS
FCC Part 68 Registration
This device complies with FCC Part 68 rules, and the use of
this device is subject to the following restrictions:
1. The FCC has established rules which permit this device to be
directly connected to the telephone network. Standardized jacks
are used for these connections. This equipment should not be used
on party lines or coin phones.
2. If this device is malfunctioning, it may also be causing harm to
the telephone network; this device should be disconnected until
the source of the problem can be determined and until repair has
been made. If this is not done, the telephone company may
temporarily disconnect service.
3. The telephone company may make changes in it's facilities,
equipment, operation and procedures; if such changes affect the
compatibility or use of this device, the telephone company is
required to give adequate notice of the situation with the FCC.
4. If the telephone company requests information on what equipment
is connected to their lines, inform them of:
a. The telephone number to which this unit is connected.
b. The Ringer Equivalence Number (REN).
c. The USOC jack required.
d. The FCC Registration number.
Items (b) and (d) are indicated on the label. The Ringer
Equivalence Number (REN) is used to determine how many
devices can be connected to your telephone line. In most
areas, the sum of the REN's of all the devices on any one line
should not exceed 5.0. If too many devices are attached, they
may not ring properly.
FCC Part 15 Registration
This device complies with Part 15 of FCC rules. Operation is
subject to the following two conditions:
1. This device may not cause harmful interface, and
2. This device must accept any interface received including
interface that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and receiver
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult an experienced radio/TV technician for help.
CTR 21 pan-European Certification
This equipment has been approved in accordance with
Council Decision 98/482/EC for pan-European single
terminal connection to the public switched telephone network
(PSTN). However, due to differences between the individual
PSTNs provided in different countries, the approval does not,
of itself, give an unconditional assurance of successful
operation on every PSTN network termination point. In the
event of problems, you should contact your equipment
supplier in the first instance.
This device is designed to work with the notified networks in
all EC member states. Nevertheless, some of the network
services in invidual countries might not be supported, but
they will not affect the normal data and fax applications. For
example, the metering charge service in Germany. Besides
you may encounter difficulty of using PULSE dialing
function in some of the countries, such as Nordic countries.
This kind of network compatibility is dependent on the
physical and software settings of this device. If the users are
desired to use this device on those networks, they should
contact the vendor or supplier first.
HARDWARE INSTALLATION
Precautions:
Please be sure you take adequate anti-static
precautions when handling this product. The
simplest way to achieve this is; before you begin
and every minute or so during the hardware
installation touch a non-painted surface of the
computer’s chassis.
1.
2.
3.
4.
5.
6.
Before installing the device, make sure the
computer is turned off.
Remove the expansion slot cover from the
computer.
Carefully slide the PCI modem card into an
available PCI slot, push it evenly and firmly
home and ensure it is screwed securely in
place using the mounting screw (PCI slots
are 85mm long and positioned 40mm from
the PC’s rear panel. Generally there are
several PCI slots side by side).
Plug one end of the telephone cable into the
Modem line jack and the other end to the
telephone jack in the wall.
Replace the cover.
After hardware installation is done, move on
to the software installation.
-1-
SOFTWARE INSTALLATION
Windows 98 Installation
1.
2.
3.
Restart the computer system after the
modem is correctly plugged into the PCI
slot of your computer. Windows will
automatically detect the device. Click Next.
When the following dialog box appears,
insert the device driver compact disc into
your CD-ROM drive and click Next.
Select Specify a location and press Browse
to choose the folder driver/win98 in your
CD-ROM drive. Then click Next.
-2-
4.
Click Next to continue.
5.
When the following figure appears, click
Finish. The Installation program will
continue.
-3-
6.
Follow the
proceed.
on-screen
instructions
to
7.
The program will proceed automatically.
Click Finish to complete software
installation.
Windows 2000 Installation
Restart the computer system after the modem is
properly plugged into the PCI slot of your
-4-
computer. Windows 2000 will automatically
detect the device. If you want to use the
Microsoft
built-in
driver,
execute
d:\Driver\Win2000\PAR.exe (assume that d: is
your CD-ROM drive). Or you may update the
device driver with the utility provided by the
manufacturer.
1.
Go to Control Panel, double-click System.
Select Hardware. Click Device Manager.
2.
Right-click LT Win Modem.
Properties.
-5-
Select
3.
Select Driver.
Driver…button.
4.
Follow the on-screen instructions to proceed.
(Click Next to continue.)
Load the Compact Disc that contains the
device driver into your CD-ROM drive.
5.
Click
-6-
the
Update
Click Browse and select the proper file
location with the disc drive followed by
Driver\Win2000.
6.
Check Install one of the other drivers.
Click Next.
7.
Select
d:\Driver\Win2000\ltmdmnt.inf,
click Next.
-7-
8.
When Windows prompt you to continue the
installation. Select Yes.
9. Click Finish to complete the software
installation.
Windows ME Installation
Restart the computer system after the modem is
properly plugged into the PCI slot of your
-8-
computer. Windows ME will automatically
detect the device. If you want to use the
Microsoft
built-in
driver,
execute
d:\Driver\WinME\PAR.exe (assume that d: is
your CD-ROM drive). Or you may update the
device driver with the utility provided by the
manufacturer.
1.
2.
3.
Right-click My Computer, then click
Properties Device Manager.
Click WDM Modem Enumerator to
expand.
Load the device driver into your CD-ROM
drive. Click Properties Driver Update
Driver.
-9-
4.
Select Specify the location of the driver
(Advanced) and click Next.
- 10 -
5.
Select Display a list of all the drivers…and
click Next.
6.
Click the Have Disk…button.
7.
Click Browse to select the drive where the
device driver exists. (for example: D:\)
- 11 -
Enter the CD-ROM driver letter followed by
driver\Win_ME.
8.
Click Next.
9.
Click Next to proceed.
- 12 -
10. Click Finish to complete the software
installation.
Note: Windows ME users who experience low
connection speeds to their Internet provider can
apply a driver update to improve speeds. To do
this, insert the modem driver CD, (you will need
to press Exit when the PICShell software
installation utility starts).
Click on Start,
Programs, Windows Explorer. Now explore
the CD-ROM by opening the Driver folder, then
Win_Me_faster.
Double-click
on
Driver_update.exe, this will lead you through
the upgrade process.
Windows XP Installation
Restart the computer system after the modem is
well inserted into the PCI slot of your computer.
Windows XP will automatically detect the
- 13 -
modem. Perform the following procedures to
install the driver.
1.
Load the device driver CD into your CDROM drive. Close the window that
automatically pops up.
2.
Go to Start Run. Click Browse to
direct your system to the location where
contains the device’s driver (e.g.,
E:\Driver\Win 2000&XP\Setup). Click
OK.
3.
Click OK to install the driver.
4.
When the following window appears,
click Continue Anyway to complete the
software installation.
- 14 -
5.
Go to Start Run, enter “regedit”, and
click OK.
6.
Select HKEY_LOCAL_MACHINE, and
click SOFTWARE to expand. If the
Lucent and Modem are listed as below,
the modem exists and is successfully
enabled. If not, consult your distributor
for the technical support.
- 15 -
Windows NT Installation
1.
2.
3.
4.
5.
6.
Reboot the computer system after the
modem is correctly plugged into your PCI
slot of computer.
Load the device driver compact disk in the
CD-ROM drive.
Start Windows NT.
Go to My Computer.
Click the CD-ROM drive. Click the
driver\winnt folder. Or you may click the
Browse button to select the CD-ROM drive
and the driver\winnt folder.
Double-click setup.exe. The installation
program will proceed automatically.
- 16 -