Technical information | Acer 3000 series Laptop User Manual

Acer Ferrari 3000 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PART NO.: VD.FR1V7.001
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Ferrari 3000 service guide.
Date
II
Chapter
Updates
2003/11/17
Chapter 4
Add POST codes
2004/04/29
Chapter 3
Correct CPU removing SOP on page 56.
Copyright
Copyright © 2003 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
Chpater 1
System Specifications
1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front Open View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Left Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Right Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Bottom Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Lock Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Embedded Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
The Euro Symbol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Launch Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Touchpad Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Chapter 2
System Utilities
31
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
BIOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
System Diagnostic Diskette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Chapter 3
Machine Disassembly and Replacement
45
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the Optical Module/HDD Module/
Wireless Lan Card and LCD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Optical Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Wireless LAN Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Disassembling the Main Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Remove the function key board and the keyboard . . . . . . . . . . . . . . . . . . .53
Separate the main unit into the logic upper and the logic lower assembly .53
Disassembling the logic upper assembly . . . . . . . . . . . . . . . . . . . . . . . . . .54
Disassembling the logic lower assembly . . . . . . . . . . . . . . . . . . . . . . . . . .55
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
VII
Table of Contents
Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Disassembling the HDD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . .59
Chapter 4
Troubleshooting
61
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Keyboard or Auxiliary Input Device Check . . . . . . . . . . . . . . . . . . . . . . . . .62
Memory check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Touchpad check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
POST Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Chpater 5
Jumper and Connector Locations
79
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Chapter 6
FRU (Field Replaceable Unit) List
81
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Appendix A
Model Definition and Configuration
90
Ferrari 3000 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90
Appendix B
Test Compatible Components
91
Microsoft® Windows® XP Home Environment Test . . . . . . . . . . . . . . . . . . . . . .92
Appendix C
Index
VIII
Online Support Information
97
99
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
AMDTM XP-M processor at available in 2500+ and higher
T
Memory upgradeable up to 2GB with 2 slots (only one slot for user accessible)
T
Internal removable DVD drive (AcerMedia bay)
T
High-capacity, Enhanced-IDE hard disk
T
Li-Ion main battery pack
T
Microsoft Windows XP operating system
T
Thin-Film Transistor (TFT) liquid-crystal display (LCD) displaying 32-bit high colour up to
1400X1050 Super eXtended Graphics Array (SXGA+) resolution for 15.0”
T
3D graphics engine
T
Simultaneous LCD and CRT display support
T
S-video for output to a television or display device that supports S-video input
T
“Automatic LCD dim” feature that automatically decides the best settings for your display and
conserves pwer
Display
T
DualViewTM
Multimedia
T
AC’97 stereo audio
T
Built-in dual speakers
T
Built-in microphone
T
High-speed optical drive
T
Built-in optical drive (DVD dual)
T
15.0” TFT SXGA+ (1400x1050 resolution) panel
T
Audio input and output jacks
Connectivity
Chapter 1
T
High-speed fax/data modem port
T
Ethernet/Fast Ethernet port
T
Fast infrared wireless communication
T
Four USB 2.0 (Universal Serial Bus) ports
T
IEEE 1394 port
T
Invilink 802.11g wireless LAN (manufacturing optional)
T
Bluetooth ready (manufacturing optional)
T
SD/MMC/SM/MS memory slot (manufacturing optional)
1
Keyboard and Pointing Device
T
86-/87-key Windows keyboard
T
Sleek, smooth and stylish design
T
Acer FinTouch full-sized curved keyboard
T
Ergonomically-centered touchpad pointing device with four-way scroll button
Expansion
T
One type II CardBus PC Card slot
T
Upgradeable memory
T
One Card bus type II slot
T
One RJ-11 jack for 56Kbps fax/modem
T
One RJ-45 jack for LAN
T
One DC-in jack for AC adapter
T
One ECP/EPP compliant 25-pin parallel port
T
One external 15-pin VGA port
T
One speaker/headphone/line-out jack
T
One audio line-in jack
T
One microphone-in jack
T
Four USB 2.0 ports
T
One IEEE 1394 port
T
One S-video (NTSC/PAL) output port
T
4-in-1 Card Reader (Manufacture optional)
T
FIR (Fast Infred) port
I/O Ports
2
Chapter 1
System Block Diagram
5
4
3
2
1
ZI3 SYSTEM BLOCK DIAGRAM
PCI ..CLOCK
AMD Processor ( Socket A )
CK-GEN3V
VCC_CORE
DC/DC
2.5V
ICS950902
P4,5
P3
D
DATA
Battery
Charger
DATA
LCD/INV
CONN
P29,30
200/266/333/400MHZ
North Bridge
VIA KN400
INTA
DDR
DIMM
H/W
MONITOR
THERMAL DIODE IN
2.5VSUS
SMDDR_VTERM
P22
DDR
DIMM
VCC_CORE
1.5V
2.5V
2.5VSUS
3.3V
P33,34,35,36,37,38
P14
P6,7,8
P10
2'nd FAN
C
C
P22
CH7019
V-LINK
266/533MB/s
TV ENCODE R
P14
& LVDS
HDD
D
AGP BUS
P15
VIN
2.5V
3.3V
CTRL
TV-OUT
POWER IN
ADDR
EXT. VGA
ATI M9+X
P15
CTRL
ADDR
5V
CRT
19V IN
P27,28
5V,3V,CPUCORE VCC etc.
5V
P21
CD-ROM
5V
USB
CONN
5V
UltraDMA 100/133
PCI BUS
South Bridge
VIA VT8235
P21
3V
3VSUS
2.5V
RVCC
USB 2.0
MII
PCMCIA
TI1410
LAN PHY
VT6103
P11,12,13
P22
3V_LAN
3V
3VSUS
5VSUS
12V
P25
B
Audio
Amplifier
G1421
5V
P20
AC97
Realtek
ALC202
3V
5V
AC'97 Link
3V
Primary
INTB
REQ0
GNT0
AD18
RJ45
SIO
PC87393
1394
TSB43AB21
INTB
REQ1
GNT1
AD19
P25
MDC
AC'97 Link
5VPCU
P24
P25
1394
CONN
Slot0
3V_MODEM
5V
3VSUS
B
P23
P18
RJ11
INT C/D
REQ2
GNT2
AD20
P18
P16
P19
EC/KBC
PC87570
MINI-PCI
3V
3VSUS
5VSUS
3V
LPT
Port
5V
P23
3V
P17
FIR
P16
P26
Secondary
P19
A
A
LED/B
CONN
5V
Touch
Pad
P17
5V
BIOS
P17
5VPCU
Keyboard
P26
P16
FAN
5V
P22
Size
Document Number
Custom
Date:
5
Chapter 1
4
3
2
Rev
1A
Block Diagram
Tuesday, September 23, 2003
Sheet
1
of
38
1
3
Board Layout
Top View
3
2
PD1
PC1
PD2
PR1
PQ1
HOLE15
R591
R594
PC5
L18
C4
L19
C5
C6
L20
C7
L21
C8
C9
L22
C10
C29
R34
R33
3
CN5
7
H
PR11
PR3
PR4
RP3
2
U4
HOLE21
PR15
PC15
PR14
PC17
PR5
PC6
PC20
PR8
PC12
PC14
CN6
PR6
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
L17
L15
R584
L16
R26
L11
L12
L13
L14
R25
R583
R24
R28
R27
L6
L7
C21
C20
C19
C22
C24
C25
C26
PQ36
C32
PR7
PR9
PR12
R592
PC16
PR17
PC23
PR16
PQ4
PQ53
PQ6
HOLE24
PR31
PU2
PR30
HOLE26
PR35
8
C50
C91
PC42
PR42
PQ10
PQ11
PR43
PR44
PR45
PR46
PR47
PU4
47 49
C170
PC43
4
G
I
R123
3
R135
HOLE35
G
PQ21
10
I
O
G
I
O
PQ23
T33
PR138
O
G I
O
G
PR139
PL8
PC152
C178
PU12
O
C207
11
PQ52
PQ51
PC60
R593
C278
PD9
PR77
12
C327
C333
R232
PC69
PR78
PC70
PL10
PL11
PC74
PC75
PR79
PC76
HOLE41
C308
R192
R197
R199
C325
5
PQ26
PC63
C268
C269
C281
C188
C190
R125
PC151
C184 C185
R121 R122
PR53
R179
C322
C323
PC52
R601
PQ31
PQ29
C301
R120
HOLE40
PR64
PR65
PR63
PQ28
PC65
D11
D12
C306
C307
C264
C270
C285 C267
R597
L42
L43
L44
CN15
PQ12
PR41
PQ9
PR40
CN18
PC44
PC45
C220
PL6
PR61
PQ22
PC59
9
R116
C163
R186
C986
C293
G
19
L46
PR59
PC62
C277
C283
C292
C300
C305
C318
PC72
CN19
PC73
PC71
PQ34
PR80
PC77
C314
C315
C313
C316
C312
C317
C319
C272
C266
C294
C90
PC37
PQ7
C111
C112
C113
C114
C115
Q16
PQ18
PU6
PL9
PU7
R596
G
G
C262
C274
C282
R588
R250
PR67
PR71
PQ24
PR73
PR62
PR66
PR68
PC55
PR72
GI
I
PQ15
PQ25
PR75
O
O
20
2
C218
PQ17
PR57
PR60
PQ19
PC49
PC54
C275
C276
M 1
1
0
L D
I
S D
D1
I
D2
Q18
2
2
1
E
J
M
4 8
3
2 4 8
F GH
K L
N
CN29
C372
R295
R296
R279
HOLE52
8
U15
HOLE48
CPAD4
CPAD3
CPAD2
DA0ZI3MB6D7 REV:D
HOLE53
CPAD1
SW1
3
R298
C377
C378
C380
PQ30
O
G
PR51
I
PR55
PQ20
PC47
PC48
R263
44
A
A
PR147
PC7
PC2
CN30
PC4
PC10
PR36
PC36
5
PR56
PR58
PD10
PD11
C287
C296
C299
C311
C303
C298
CN20
4
PC32
L37
RP28
RP27
RP26
RP29
RP30
C127
C126
C152
C153
C154
C122
C151
C120
C119
C121
C104
C149
C148
C150
C147
C146
C145
PAD31
PL19
PC150
PL21
PC153
4
2
PR21
C125
HOLE45
C381
C382
L8
L9
L10
HOLE8
L1
R1
L2
L3
L5
L4
D8
U3
U2
C28
PC24
L31
PC26
PC28
C47
D C B A
H G F E
L K J
RP25
RP24
RP23
RP22
RP19
RP20
RP21
RP33
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
RP16
RP17
RP18
RP32
RP31
C116
C143
C144
C141
C142
C108
C109
C110
C140
C139
R113
C134
C135
C136
C137
C138
C124
PQ14
R293
Q20
C383
10
M
N
R P
U T
Y W V
AC
AE
AE
RP15
RP14
RP12
RP13
RP11
C107
R104
RP10
PC50
C252
C253
HOLE37
R176
R177
C261
R202
C230
9
AA
AB
AD
AF
AA
AB
AC
AD
AF
PR37
C988
PR76
R200
R201
C321
R223
R222
D14
Q19
GI
HOLE51
8 14 13
15
HOLE29
E
E
CN16
C193
C194
C195
C196
C197
34
68
RP36
C249
C250
RP42
RP44
R219
R217
R218
R602
RP50
HOLE50
O
G
PC66
C320
R211
Q49
O
G
I
G
I
PC67
C288
C297
R234
C340
R242
R598
R229
R230
R231
RP47
C225
R158
R159
R160
R161
C226
C227
C228
C229
C364
F
F
T55
C363
L48
O
C373
PR33
PL4
C83
PC53
PQ27
R595
C210
R152
C223
PR2
C30
R35
Q15
PR18
PR19
PR20
16
PC31
C
C
PD8
PC61
O
D13
R286
R287
C235
R268
R270
R272
R288
C375
PAD47
R289
R297
R292
C379
RP46
T54
T56
C371
R267
R283
PAD46
T57
C370
R278
R281
R282
R274
R277
R291
R294
R284
R285
C374
R276
C234
PR52
PR54
PD7
PC56
R215
C331
R224
Q21
T44
C339
C344
C345
L56
C980
R260
R226
R227
R228 R245
R246
R247
R259
C367
R240
RP48
C369
R265
R290
R273
L32
PR24
PR25
PC27
PR26
PR27
PR28
C34
18
19
20
21
22
23
24
25
26
17
12
13
14
15
16
T1
T2
11
9
6
8 T3
1
2
3
4
5
7
B
D
E
L34
H G F
J
C46
K
R P N ML
C73
U T
Y W V
C74
PR38
D10
C81 C77
C82 C78
C53
D9
C51
R79
R80
C79
C80
R114
C202
C203
C204
C205
R167
R168
R169
T34
C256
C258
T36
C302
R189
PAD43
R271
L63
C87 R82
R83 C84
C85
C55
U8
R76
R86
R87
R88
R89
R90
R91
R94
R95
R96
R97
R98
R99
T14
T13
T16
T19
C93
T20
T18
C162
R118
C989
C174
L45
C200
C201
R127
AF
AG
AH
AJ
AK
AC
AD
AE
C164
C172
C176
C158
C159
C160
C168
C191
RP37
C248
T43
R256
C365
C291
R180
L53
C336
C334
C335
C358
C360
C361
L55
R266
CN21
C981
PC25
PR29
PR32
C44
I
RP45
R241
C347
R236
C342
C346
C351
C352
R235
C341
R243
C350
R249
PR23
PR144
PR70
PC64
R233
C338
C368
R280
L61
L62
25
CN17
PL5
11
Q17
T41
T45
T47
PC3
C27
PC21
CN2
PR99
HOLE22
R124
1
R187
R191
C265
T42
T48
C105
PR69
PC58
R599
R600
Q7
PQ3
41
10
PC57
Q4
H
HOLE4
HOLE6
PAD9
C409
Q8
PQ44
200
20
PQ32
R178
R181
RP43
R193
L54
R237
R238
R239
T52
RP41
C271
R261
R269
L59
L60
R275
R173
HOLE3
PL1
C408
2
O
PU1
PC114
PQ13
Y1
C221
L47
C224
RP38
C247
Q50
C254
R175
L49
C260
T35
C245
R214
G
G
R170
R174
6
R29
Q10
PR82
42
40
39
C259
R262
R264
C118
E
E
PAD34
PQ16
HOLE36
I
Q5 Q6
PD3
20
PR148
G
HOLE2
HOLE7
PAD57
CN8
PQ54
PL3
8
PC51
G
CN3
R585
PQ2
PR10
199
F
R165
C343
R244
C348
U14
T96
T40
C354
R257
R258
2
R101
R103
R107
R109
R111
R115
R128
U11
R188
T46
R253
C357
R117
R119
L28
HOLE17
Q3
19
O
G
PC93
C117
R110
T37
C279
R603
C309 R203
C310 C329
C324
R213
R216
R255
PC41
35
RP39
C263 C273
C257
R251
PAD42
T53
T49
T51
L58
R252
T50
R248
C355
C359
C356
R605
R221
C330
R220
R225
C362
C332
C240
C241
R172
R171
C251
R182
C289
R183
C304
R210
T39
L51
L52
C337
C349
L57
C353
C255
C295
R194
R190
R196
R198
R184
R195
C993
R212
C328
R207
R208
R209
R204
R205
R206
C326
L50
U12
C280
C286
C290
T38
R185
U13
C244
C246
C242
R166
C243
HOLE38
PR39
CON1
PL7
C216
C219
R150
R154
R156
C222
C231
C236
65
64
32
33
C992
PU3
HOLE30
O
Q48
R100
R102
R106
D
D
PC46
R153
R155
R157
C232
R162
R163
C237
R164
C238
C239
PC34
R151
C233
Y2
C198
C199
R141
R149
C192
R140
C217
R148
C284 RP40
97
128
96
T31
T32
C215
C366
C208
C974
C975
R126
T24
U10
C973
R138
C171
T22
T23
R137
R139
R142
L35
C57
R69
R73
R70
R68
C56
C59
R67
G
D
E
C165
C157
RP34
C972
C211
R143
R144
R145
R146
R147
C212
C213
C214
C209
T28
T29
T27
T30
R136
T21
C131
C173
C967
C180
C181
C183
C187
C189
C186
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
F
A
B
C
C102
C161
C177
C182
T26
T25
C130
C179
U9
I
G
R65
R71
R74
C984
C64
C89
C95
C156
C103
15
L41
C100
C60
9
8
7
6
5
4
3
2
1
C45
R64
R66
L36
PQ8
T17
10
C128
C965
C129
R92
R93 C94
C96 C92
C106
PC38
PC39
PC40
R84
T6
R63
T8
R77
R78
C86
C88
C70
C75
RP49
R85
H
J
C98
C99
C964
1
4
1
C963
C97
C101
D
D
R81
15
14
13
12
11
T15
4
L39
L40
C48
C49 C
C
C52
C63
C62
L38 PC33
PC35
R75
U6
C376
RP9
C132
RP35
C133
4 3 2
CN14
RP8
3
2
3
2
C961
C962
T12
T11
C72
C76
C54
R72
T10
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R134
C206
R129
R130
R131
R132
R133
C966
C175
C69
C71
C166
C167
C169
C65
C67
C68
C66
C960
HOLE28
C58
R108
R112
R60
2
1
N
C
C61
R56
R57
C38
C39
R62
R61
C
C42
3
2
3
L33
1
4
O
I
T5
A
R58
T4
R59
16
10
C40
C41
C37 R55 C35 C36
U7
C43
HOLE25
HOLE23
R30
R31
10
2
3
R54
PAD10
HOLE14
40
PC9 PR13
C123
1
4
CN13
RP2
PL2
PD6
R53
L30
C33
CN11
RP1
39
CN7
C155
L29
R51
R52
2
11
R48
R50
HOLE20
C18
36 34 32 30 28 26 24
29 27 25 23
37 35 33 31
3
C16
L26
6
8
4
2
22 20 18 16 14 12 10
9
15 13 11
7
5
3
1
21 19 17
R46
R47
4
R49
Q13
Q11
R43
R44
2
1
R587
R45
Q14
R40
HOLE16
1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 10 23 11 24 25
13
12
CN4
U5
C426
I
C427
O G
I D6
B
B
Q12
L27
CN10
R38
R39
R41
R42
B
B
5
O G
R12
I
RP7
1
3
RP5
RP6
2
R36
RP4
C31
R37
Q9
R32
C23
1
4
4
3
A
A
O G
PC30
PR34
PC29
2
D1
HOLE11
C1
L24
C2
C3
L25
O
AN
AM
AL
C12
AK
AJ
AH R5
AG
AF D2
AE
AD
AC
AB
AA
Z
D3
Y
X
W
V
U
R7
T
Q2
6
G D4
20
3
GI
R3
2 7
C13 R6
PAD13
CN9
I
F
E D5
D R10
C
B
A
R11
D7
5
S
C14
R
Q
P
N
M
L
C15
K
J R8
H
R9
G
9
Q1
4
L23
OG
U1
I
8
O
CN1
HOLE1
16
I
17
5
6
11
7
12
8
13
9
14
10
15
R2
R4
C11
R13
HOLE5
4
D15
HOLE49
13
14
4
1
CPU socket
10
DIMM socket HDD connector
2
S-video port
11
Keyboard connector
3
CRT
12
Main battery connector
4
Docking
13
IR
5
RJ45
14
HDD connector
6
RJ11
15
PCMCIA slot
7
Power jack
16
IEEE 1394 port
8
LCD connector
17
Four USB ports
9
Optical drive connector
Chapter 1
Line-in connector
2
Microphone-in connector
3
Line-out connector
4
Mini PCI connector
5
DIMM socket
T95
T94
M 1
D1 1
D2 0
L D
I
S D
2
2
1
E
J
M
4
3
2
F
K
N
4 8
GH
L
8
DA0ZI3MB6D7 REV:D
C948
R604
E
R566
C934 R572
C936 R574
I G I
C942
C944
C946
C947
G I
RP100
R545
R548
R550
JP15
C929
Q43
O
R560
2
Y8
C930
C933
C935
C938
R576
R564
O Q45
G
D33
I
45
88
89
16
14
12
8
9
9
1
2
3
4
5
6
T85 7
Y W V U T R P
D24 C900
8
ML
T79
R P N ML K J
H
J
U40
G F
E
G F
T92
D
D
C904
C902
B
B A
U37
176
U41
4
K
R471
D20
R525
U29
RP85 C985
RP86
RP84
C866 C864
T93
C873
C876
C880
C882
44
D25
5
C918
4
4
HOLE44
13
14
133
132
5
D
A
11
C862
C869
C912
O
U43
C700
B
U27
K
F
D
M
H
J
L
C788
R458
108
109
C863
C894
R547
Y7
13
C916
R580
8
C955
M
C729
R454
T91
12
48
L90
M
G
A
R528
25
26
50
51
30
29
7
5
3
1
2
20
C943
L89
U25
U38
H
L
C662
C649
R419
1
3
5
7
4
2
10
11
12
9
8
6
C613
R405
C969
Q36
HOLE27
C562
R391
R398
C970
C603
C612
128
R384
R395
R394
R393
R392
C713
C569
C735
C734
C786
R490
C839
C843
C855
Q40
U31
C875
C878
U34
100
T87
24
37
36
25
C915
U36
21
R578
R579
C949
C953
C956
C959
C958 C957
C
G
E
R441
73
C835
I O
G
C845
C850
C800
R483
R484
D18
R486
C834
C836
C838
L83
C842
C844
C846
C849
RP95
T88
T89
M
C927
R561
R565
R567
R573
C937
R575
C939
C952
D29 D
D30
D31
C951
U44
U21
R377
R380
C554
C557
C564
C565
C519
R357
C479
C450
U18
C464
R353
C482
PR103
PR104
R351
R350
Q31
C435
C431
U45
2
L78
C619
C559
R334
Q29
R589
C407
C406
U16
C405
R317
R316
R315
R314
R313
R312
F1
R311
R310
L64
PAD56
C618
C627
C626
C425
C424
C423
C422
RP51
R586
C436
R347
C430
R345
C446
C429
PC8
O
R354
C463
G
I Q27
R337
R336
Q30
R339
CN23
PR143
PC13
R348
PR93
C432
C433
PC80
PD14
PQ35
PC81
PC79
PC155
PL16
PC18
PD4
PC78
Q33
RP52
PL14
C478 C476 C449
R356
C508
C511
C512
C513
C514
C494
R424
C667
C651
C653
C652
C665
C654
C650
R412
R411
R410
C971
R401
R399
C540
C549
C517
R359
C527 C523
C522
C525
C537
U20
R426
R425
R420
C675
R427
8
6
4
C676
R423
R422
R421
R414
C659
C656
M
C709
1 2 3 4 5 6 7 8 9 10
K
9
10
11
12
C977
C692
C711
U28
G
R438
11
C664
C682
C685
C677
C686
C683
U23
C625
C661
R415
C666
C663
T70
C660
C657
C978
T68
B
R440
C694
C693
C697
T77
C691
C696
C690
C670
C658
C671
D
G
R439
C
PAD55
T76
T75
C699
C976
C674
C673
C688
J
C792
PC124
R432
R431
R430
T74
C861
R518
C789
R462
H
144
R468
D
RP83
R517
C791
F
T80
E
C982
RP89
E
T82
T81
6 5 4 3 2 1
J
T84
L
11
G
13
C852
C853
R513
12
C983
B
15
Y W V U T
C790
R465
R464
R463
A
R534
R485
C
17
C858 C857
R515
Q42 O Q41
I
5 U30 4
G
R496
C672
Q35
C941
RP96
C854
C668
C678
L80
F
C913
RP98
C705
C704
C707
C706
C543
R360
C534
C533
C532
C531
T9 T7
L71
C535
C539
C551
C550
C940
L87
RP97
K
C799
F
R461
R460
R467
C793
R466
H
R493
M
C687
C695
C606
C648
L79
L92
48
I
1 2 3 4 5 6 7 8 9 10
G
G
C950
U33
D
R498
HOLE32
B
T71
C679
C669
C681
C607
R408
C620
L94
RP93
10
RP92
RP94
G
T73
C968
C906
U35
2
18
D22
R435
C689
R500
R607
C899
R476
R475
R474
R473
R472
C714
R443
C684
19
3
20
4
Y5
R529
C868
HOLE39
D21 C872
G
G
Y4
21
PC140
R477
C728
22
R489
R491
R492
R494
R497
C655
R524
R523
R522
R521
R520
C865
PC132
R481
R480
R479
R404
R407
C638 R409
R413
L91
C914
C919 O
C928
PU11
R433 PR122
U26
R502
R514
C901
C903
C907
C908
C910
L85
R482
42 40
R478
C795
C680
R508
R507
R506
R505
R504
R503
C895
C847
R512
R511
R510
T78
R509
B
R516
RP87
C859
2
D19
R519
H
H
R418
R417
Y3
23
PR135
R526
C698
C701
D17
AC
AB
AA
PC120
C647
C646
103
102
24
C874
U22
25
R530
64
AF
AE
AD
PR136
R385
R378
R379
R383
R387
R389
R396
C598 R382
R386
R390
R397
26
H
H
38
39
T83
PC134
39
PC121
PR121
PR120
R428
C
C
PC122
PC123
R429
C567
T86
CN24
C584
R608 R606
C994
PL20
R455
C732
C723
L72
U32
R535
10
11
C796
R554
C898
C897
R553
R552
R551
C896
65
A
16 14 12
13
17 15
C840
C530
C802
II
C804
C803
C724
C805
R368
R370
R369
C545
L76
L84
18
RP81
C806
41
C807
199
L74
R367
R366
PC133
C566
PC143
PR128
PC144
PR127
PR126
T63
T62
C544
C529
R365
R364
R363
R362
R361
C518
24
22 20
25
23
21
PC145
C808
C556
R403
R358
C448
C451
R540
R539
R538
26
G
O
PR131
R376
PD20
C622
C611
C461
C917
AF
AE
AD
AC
AB
AA
O
PC146
R342
L77
C596
R332
C421
C401
C400
C399
C389
C388
C387
C386
C385
C390
C391
C398
C397
C396
C395
C394
C393
C392
R300
R308
R307
R305
R304
R301
C402
T59
Q25
Q22
R333
C410
C416
R324
R373
R323
R322
R321
C411 R372
R320
C547
R319
C546
U17
R325
C412
C413
R326
C414
R331
R330
C415
R329
R328
R327
R318
L93
G
T66
C624
U19
Q26
I
RP103
I
T69
FF
G
RP102
24
RP91
R532
I
RP82
C528
R590
R555
R559
R558
R557
C879
C794
C536
PR132
G
C560
C561
C495
C510
PC19
29
30
C460
C404
U39
C909
C911
R544
RP101
C821
C822
C553
C555
C558
C823
C826
T67
C516
PC103
PR142
C462
PR134
PR133
JJ
L67
PC141
PR130
PR129
I
PC142
L81
C524
L68
T61
U42
BT1
PR124
PR125
C837
PC139
C417
RP104
C892
G
RP105
Y6
R537
R541
C883 C884
C886
R542
C885 C888
C887 R543
C889
RP99
C890
C893
R549
C801
C477
R299
A
C541
D32
C881
O
C
C
C552
Q47
Q46
R531
C538
PC147
PR137
C832
T60
PC148
G
C542
C548
C926
C925
C932 C924
C931 C923
C922
C921
C920
C877
C563
C581
L66
C824
C798
Q23 R303
C403
L86
R577
D28
JJ
C507
O
G
Q44
C726
C445
I
25
C418
Q52
C833
L82
L69
C526
L73
C825
O
C481
C496
Q51
R453
C727
R306
R581
C730
PQ47
200
PL18
O
C600
C579
PC118
PQ49
I
R371
R374
PC138
PC137
Q37 R469
L70
I
PC136
PC135
C616
G
PD21
G
C521
R582
T72
PC117
O
C954
C708
C580
PL17
C725
PQ5
C797
PC119
PR123
C520
PC130
PQ48
PR119
PR118
PC115
PC22
PQ50
PQ45
PC106
C760
C759
C758
C757
C756
C755
C754
C753
C752
C751
C750
C749
C748
C747
C746
C745
C744 RP57
C743 RP56
C742 RP55
C741 RP54
C740 RP53
C739
C738
C710
C582
PC104
CN26
FF
D23
II
C586
C595
C601
C609
C615
C623
PQ46
C591
PR22
C891
R546
5
C617
C731
PU13
Q38
C568
C578
C585
C594
R400
R406
C614
C621
R470
Q34
PC154
6
I
PU9
4
R309
C419
7 8
1
3
R556
C905
PC131
PR146
C428
D26
C820
C819
C818
C817
C816
C815
C814
C813
C812
C811
C810
C809
PC98
PR97
PC99
PR96
PR89
PC91
PC90
PR149
D27
R569
R568
C831
C830
C829
C828
C827
PR88
PR87
PR84
R562
PC116
PR108
PR83
C571
C576
C577
C575
C574 C990
R381
C573
C572 T65
R388
C991
C570
T64
G
PC89
PC101
PC108
PR112
PC112
C604
C608
C480
PR145
C605
PD19
I
G
PQ42
PR105
PR110
O
C599
C593
C592
C589
C590
C587
PR114
PQ38
C444
C443
C442
C441
C434
R344
R343
C440
C439
C438
C437
PQ40
I
PC149
C475
C474
C473
C472 C459
C471 C458
C470 C457
C469 C456
C468 C455
C467 C454
C466 C453
C465 C452
PU10
PR100
PR106
PC110
PC82
D16
19
R563
RP80
RP79
RP78
RP77
RP76
RP75
RP74
RP73
RP72
RP71
RP70
RP69
R457
RP68
RP67
RP66
RP65
R456
RP64
RP63
RP62
RP61
RP60
RP59
RP58
C493
C492
C491
C490
C489
C502 C488
C501 C487
C500 C486
C499 C485
C498 C484
C497 C483
R105
C506
C505
C504
C503
PD5
PQ41
PC100
PD17
PC109
PR113
PC113
C642
C645
C644
C641
C636
C635
C634
C633
C632
C631
C640
C630
C629
C628
C639
C637
PQ37
PR102
PR109
PR111
PR117
PC85
PC86
PC107
C384
O
R570
R571
C785
C784
C783
C782
C781
C780
C779
C778
C777
C776
C775
C774
C773
C772
C771
C770
C769
C768
C767
C766
C765
C764
C763
C762
C761
C712
50
48
49
47
PU8
HOLE19
PR81
R452
R451
R450
R449
R448
R447
R446
R445
R444
C722
C721
C720
C719
C718
C717
C716
C715
PD18
PQ43
PC87
G
4
1
3
2
PC97
G
I
PQ39
PC88
2
PC84
PC83
O
N
PR91
O
Chapter 1
PD15
G
O
O
PD16
PR90
PR92
PC96
PR98
PR107
PC111
PR115
Q28
G
K
PR86
R416
R302 Q24
I
H
PC95
PC92
PR95
PR101
PC102
PR116
C643
6
E
PC94
B
C420
1
C
PR85
O
PR94
CN22
HOLE12
C
PF1
R335
R338
R340
R341
Q32
R346
C447
R349
R352
O
PD13
C17
C583
C588
C602
C610
I
PL12
PL13
R402
I
C597
O
I
PL15
Bottom View
C979
R355
L65
C509
C515
R375
L75
A
E
C
F2
U24
A
PAD54
12
L
J
C702
C703
C787
C737
R459
C733
C736
72
HOLE33
R487
R488
Q39
C841
R495
R499
R501
C848
C851
36
C860
R527
37
C867
C856
C870
C871
C987
R536
RP90
R533
RP88
1
T90
U46
75
76
CN25
CN27
3
E
CN28
2
C945
L88
3
4
5
Outlook View
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Front Open View
#
6
Icon
Item
Description
1
Display screen
Also called LCD (liquid-crystal display),
displays computer output.
2
Power button
Turns on the computer.
3
Touchpad
Touch-sensitive pointing device which
functions like a computer mouse.
4
Click buttons (left,
center and right)
The left and right buttons function like the
left and right mouse buttons; the center
button serves as a 4-way scroll button.
5
Palmrest
Comfortable support area for your hands
when you use the computer.
6
Keyboard
Inputs data into your computer.
7
Status indicators
LEDs (light-emitting diode) that turn on and
off to show the status of the computer, its
functions and components.
8
Microphone
Internal microphone for sound recording.
9
Launch keys
Special keys for launching Internet
browser, E-mail program and frequently
used programs. Located at the top of the
keyboard are five buttons. They are
designated as P1, P2, P3, E-mail button
and Web browser button. P1, P2 and P3
launch user-programmable applications; Email and Web browser launch E-mail and
Internet browser applications.
Chapter 1
Front Panel
#
1
Icon
Item
Description
Speaker
Outputs sound.
2
4-in-1 memory reader
Reads cards from Smart Media, Memory
Stick, MultiMedia, and Secure Digital cards.
3
4-in-1 status indicator1
Displays activity of 4-in-1 memory reader.
4
Infrared port
Interfaces with infrared devices (e.g., infrared printer, IR-aware computer).
5
Bluetooth button2
Starts Bluetooth functionality.
6
Bluetooth indicator2
Indicates that (optional) Bluetooth is
enabled.
7
InviLink button3
Enables or disables wireless connectivity.
1
8
InviLink indicator
Indicates status of wireless communication
9
Latch
Latch for opening and closing the laptop.
3
NOTE:
1.
Four-in-one card reader is manufacturing option, subject to configuration. Only one card can operate at
any given time.
2.
Bluetooth button and indicator work on models with Bluetooth only.
3.
InviLink button and indicator work on models with wireless LAN only.
Chapter 1
7
Left Panel
#
8
Icon
Item
Description
1
Four (4) USB ports
Connect to Universal Serial Bus devices
(e.g., USB mouse, USB camera).
2
IEEE 1394 port
Connects to IEEE 1394 devices.
3
PC Card slot
The slot supports a standard Type II
CardBus PC Card.
4
PC Card eject button
Ejects the PC Card from the slot.
5
Line-in jack
Accepts audio line-in devices (e.g., audio
CD player, stereo walkman).
6
Microphone jack
Accepts input from external microphone.
7
Headphone/Speaker/
Line-out jack
Connects to headphones or other line-out
audio devices (speakers).
Chapter 1
Right Panel
#
1
Icon
Item
Optical drive
Description
Depending on your model, the optical drive
is one of the following:
DVD-ROM drive for reading CDs and
DVDS.
DVD/CD-RW combo drive for reading CDs
and DVDs and writing to CD-RWs.
DVD dual for reading both DVD+/- RWs
and writing to DVD+/- RWs.
Chapter 1
2
Optical disc access
indicator
LED that indicates when an optical disc is
being read or written.
3
Optical drive eject
button
Press the eject button to remove a disc
from the optical drive.
4
Optical drive
emergency eject hole
Used to eject an optical disc when the
computer is turned off.
5
Power jack
Connects to an AC adapter.
9
Rear Panel
#
10
Icon
Item
Description
1
Modem jack
Connects to a phone line.
2
Network jack
Connect to an Ethernet 10/100-based
network.
3
Parallel port
Connects to a parallel device (e.g., parallel
printer).
4
External display port
Connects to a display device (e.g., external
monitor, LCD projector).
5
S-video
Connects t a television or display device
with S-video input.
6
Security keylock
Connects to a Kensington-compatible
computer security lock.
Chapter 1
Bottom Panel
#
Icon
Item
Description
1
Battery bay
Houses the computer’s battery pack.
2
Battery release latch
Unlatches the battery to remove the battery
pack.
3
Battery lock
Locks the battery in place.
4
Mini-PCI slot
Slot for adding mini-PCI cards.
5
Hard disk protector
Protects the hard disk from accidental
bumps and vibration.
6
Hard disk bay
Houses the computer’s hard disk (secured
by a screw).
7
Memory compartment
Houses th computer’s main memory.
8
Cooling fan
Helps keep the computer cool.
Note: Don’t cover or obstruct the opening
of the fan.
9
Chapter 1
Personal identification
slot
Insert a business card or similar-sized
indentification card to presonalize your
computer.
11
Indicators
The computer has three easy-to-read status indicators below the display screen. And two on the front of the
computer.
The Power and Battery status indicators are visible even when the display is closed..
Icon
12
Function
Description
Caps lock
Lights when Caps Lock is activated.
Num lock
Lights when Num Lock is activated.
Media Activity
Lights when the disc or optical drive is
activated.
Power
Lights gree when the power is on and
orange when the computer is in standby
mode.
Battery
Lights orange when the battery is charging.
Chapter 1
Using the Keyboard
The full-sized keyboardincludes an embedded numeric keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock Keys
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters are
typed in uppercase. Toggle on and off by pressing the
Caps Lock key on the left of the keyboard.
Num lock
(Fn-F11)
When Num Lock is on, the embedded numeric keypad
can be used. Toggle on and off by pressing the Fn +
F11 keys simultaneously.
Scroll lock
(Fn-F12)
When Scroll Lock is on, the screen moves one line up
or down when you press w and y respectively.
Chapter 1
13
Embedded Numeric Keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
Number keys on embedded
keypad
Cursor-control keys on
embedded keypad
Main keyboard keys
14
Num Lock On
Num Lock Off
Type numbers in a normal
manner.
Hold j while using
cursor-control keys.
Hold Fn while using cursorcontrol keys.
Hold Fn while typing letters
on embedded keypad.
Type the letters in a normal
manner.
Chapter 1
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Windows logo
key
Icon
Description
Start button. Combinations with this key perform
special functions. Below are a few examples:
+ Tab (Activates next taskbar button)
+ E (Explores My Computer)
+ F (Finds Document)
+ M (Minimizes All)
j + Windows logo key + M (Undoes Minimize All)
+ R (Displays the Run... dialog box)
Application
key
Chapter 1
Opens a context menu (same as a right-click).
15
Hot Keys
Using the Fn key with another key creates a hot key, providing a quick and convenient method for controlling
various functions.
To activate hot keys, first hold down the Fn key. Next, press the second key in the combination. Finally, release
both keys.
Hot Key
16
Icon
Function
Description
Fn-F1
Hot key help
Displays help on hot keys.
Fn-F2
Setup
Accesses the computer’s configuration utility.
Fn-F3
Power management
scheme toggle
Switches the power management scheme used by the
computer (function available if supported by operating
system).
Fn-F4
Sleep
Puts the computer in Sleep mode.
Fn-F5
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-F6
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-F7
Touchpad toggle
Turns the internal touchpad on and off.
Fn-F8
Speaker toggle
Turns the speakers on and off.
Fn-w
Volume up
Increases the speaker volume.
Chapter 1
Hot Key
Icon
Function
Description
Fn-y
Volume down
Decreases the speaker volume.
Fn-x
Brightness up
Increases the screen brightness.
Fn-z
Brightness down
Decreases the screen brightness
Chapter 1
17
The Euro Symbol
If your keyboard layout is set to United States-International or United Kingdom or if you have a keyboard with a
European layout, you can type the Euro symbol on your keyboard.
NOTE: For US keyboard users: The keyboard layout is set when you first set up Windows. For the Euro
symbol to work, the keyboard layout has to be set to United States-International.
To verify the keyboard type in Windows XP, follow the steps below:
1.
Click on Start, Control Panel.
2.
Double-click on Regional and Language Options.
3.
Click on the Language tab and click on Details.
4.
Verify that the keyboard layout used for "En English (United States)" is set to United States-International.
If not, select and click on ADD; then select United States-International and click on OK.
5.
Click on OK.
To type the Euro symbol:
1.
Locate the Euro symbol on your keyboard.
2.
Open a text editor or word processor.
3.
Hold Alt Gr and press the Euro symbol.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
18
Chapter 1
Launch Keys
Located at the top of keyboard are five buttons. The left-most button is the power button. To the right of the
power button are the four launch keys. They are designated as the mail button, the web browser button, and
two programmable buttons (P1 and P2).
NOTE: To the left of these five launch keys is the wireless communication button. This wireless
communication button works for model with 802.11b wireless LAN only.
Launch Key
Default application
Mail
Email application
Web browser
Internet browser application
P1
User-programmable
P2
User-programmable
E-mail Detection
Click right button at the Launch Manager icon on the taskbar and click on E-mail Detection. In this dialog box,
you have the option to enable disable mail checking, set the time interval for mail checking, etc. If you already
have an email account, you can fill in User Name. Password and POP3 Server in the dialog box. The POP3
Server is the mail server where you get your email.
Chapter 1
19
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor
responds as you move your finger on the surface of the touchpad. The central location on the palmrest
provides optimal comfort and support.
NOTE: If you are using an external USB mouse, you can press Fn-F7 to disable the touchpad.
Touchpad Basics
The following items teache you how to use the touchpad:
T
Move your finger across the touchpad to move the cursor.
T
Press the left (1) and right (3) buttons located on the edge of the touchpad to do selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad produces similar results.
T
Use the 4-way scroll (2) button (top/bottom/left/and right) to scrolla page up, down, left or right.
This button mimics your cursor pressing on the vertical and horizontal scroll bars of Windows
applications.
Function
Right Button
Scroll Button
Tap
Click twice
quickly
Select
Click once
Tap once
Drag
Click and hold,
then use finger
to drag the
cursor on the
touchpad
Tap twice (at the same
speed as double-clicking
a mouse button) then hold
finger to the touchpad on
the second tap to drag the
cursor
Access context
menu
20
Left Button
Execute
Tap twice (at the same
speed as double-clicking
the mouse button)
Click once
Chapter 1
Function
Scroll
Left Button
Right Button
Scroll Button
Tap
Click and hold
the button in the
desired
direction (up/
down/left/right)
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response.
Tapping too hard will not increase the touchpad’s responsiveness.
Chapter 1
21
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
AMD Athlon
CPU package
OPGA package
CPU core voltage
1.60V/1.65V
TM
XP-M processor 2500+ and higher
BIOS
Item
Specification
BIOS vendor
Phneoix
BIOS Version
V1.00
BIOS ROM type
Flash ROM
BIOS ROM size
512KB
BIOS package
PLCC
Supported protocols
ACPI 1.0b,PC Card 95, SM BIOS 2.3, EPP/IEEE 1284, ECP/IEEE 1284
1.7 & 1.9, PCI 2.2, PnP 1.0a, DMI 2.0, PS/2 keyboard and mouse, USB
2.0, VGA BIOS, CD-ROM bootable, IEEE 1394
BIOS password control
Set by setup manual
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
512KB
1st level cache control
Always enabled
2st level cache control
Always enabled
Cache scheme control
Fixed in write-back
System Memory
Item
22
Specification
Memory controller
AMD Athlon
Memory size
0MB (no on-board memory)
DIMM socket number
2 sockets
TM
XP-M built-in
Supports memory size per socket
1024MB
Supports maximum memory size
2048MB (by two 1024MB SO-DIMM module)
Supports DIMM type
DDR Synchronous DRAM
Supports DIMM Speed
333 MHz
Supports DIMM voltage
2.5V
Supports DIMM package
200-pin soDIMM
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications.
Chapter 1
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
256MB
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
LAN Interface
Item
Chipset
Specification
VT6103
Supports LAN protocol
10/100 Mbps
LAN connector type
RJ45
LAN connector location
Rear panel
Modem Interface
Item
Specification
Chipset
South bridge/VIA VT8235
Data modem data baud rate (bps)
56K
Supports modem protocol
V.92 MDC
Modem connector type
RJ11
Modem connector location
Rear panel
Bluetooth-MODEM Interface
Item
Chipset
Specification
South bridge/VIA VT8235
Data throughput
200k bps (Blue-tooth)/56K bps (MODEM)
Protocol
Blue-tooth 1.1
Interface
USB 1.1+MDC
Connector type
RJ11 (MODEM)
Wireless Module 802.11g (optional device)
Item
Chipset
Specification
BCM4306KFB
Data throughput
11M bps
Protocol
802.11g
Chapter 1
23
Wireless Module 802.11g (optional device)
Item
Specification
Interface
Mini-PCI type II
Four-in-One Card Reader
Item
Specification
Chipset
M220V0315
Data throughput
USB 1.1
Protocol
SMC, MS, MMC, and SD
Hard Disc Drive Interface
Item
Vendor &
Model Name
HGST MORAGA
IC25N030ATMR04
TOSHIBA MK3021GAS
HGST MORAGA
IC25N040ATMR04
TOSHIBA MK4025GAS
HGST MORAGA
IC25N060ATMR04
TOSHIBA MK6021GAS
Capacity
(MB)
30000
40000
60000
Bytes per
sector
512
512
512
Data heads
2
2 for HGST
3 for TOSHIBA
3 for HGST
4 for TOSHIBA
Disks
1
1 for HGST
2 for TOSHIBA
2
Spindle
speed
(RPM)
4200 RPM
4200 RPM
4200 RPM
Drive Format
Performance Specifications
Buffer size
2048KB
2048KB
2048KB
Interface
ATA/ATAPI-6
ATA-5
ATA/ATAPI-6
ATA-5
ATA/ATAPI-6
ATA-5
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
350 for HGST
317 for TOSHIBA
350 for HGST
317 for TOSHIBA
350 for HGST
317 for TOSHIBA
Data transfer
rate
(host~buffer,
Mbytes/s)
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Voltage
tolerance
5V(DC) +/- 5%
DVD Interface
Item
24
Specification
Vendor & model name
MKE SR-8177/QSI SDR083
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (KB/sec)
Sustained:
Max 3.6Mbytes/sec
Sustained:
Max 11.08Mbytes/sec for MKE
Max 10.56Mbytes/sec for QSI
Chapter 1
DVD Interface
Item
Specification
Data Buffer Capacity
256 KBytes for MKE
Interface
IDE/ATAPI (compliant to ATA/ATAPI-5)
Applicable disc format
KMEDVD: DVD-ROM (DVD-5, DVD-9, DVD-10), DVD-R (3.95G/4.7G), DVD-RAM
(2.6G/4.7G), DVD-RW
CD: CD-Audio, CD-ROM (mode 1 and mode 2), CD-ROM XA (mode 2, form 1
and form 2), CD-I (mode 2, form 1 and form 2), CD-I Ready, CD-I Bridge, CDWO, CD-RW, Photo CD, Video CD Enhanced Music CD (CD Plus) CD-TEXT
QSIDVD:DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18), DVD-R, DVD+R, DVDRW, DVD+RW
CD: CD-DA, CD-ROM/XA, CD-i, Karaoke CD, Video CD, Multi-session Photo
CD, Enhanced CD, i-trax CD, CD extra, CD Plus, CD-Text, CD-R and CD-RW
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Eject Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
DVD Combo Interface
Item
Specification
Vendor & model name
QSI SBW-242/LiteOn LSC-24082K
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (Mbytes/sec)
Sustained:
Max 3.6Mbytes/sec for QSI
Max 3.5Mbytes/sec for LiteOn
Sustained:
Max 10.56Mbytes/sec for QSI
Max 10.15Mbytes/sec for LiteOn
Data Buffer Capacity
2MB
Interface
IDE/ATAPI-5
Applicable disc format
QSIDVD: DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18),DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-ROM (optional)
CD: CD-DA, CD-ROM/XA, CD-i, Karaoke CD, Video CD, Multi-session Photo
CD, Enhanced CD, i-trax CD, CD extra, CD Plus, CD-Text, CD-R and CD-RW
LiteOnDVD: DVD single/dual layer (PTP, OTP), DVD-R (3.8G/4.7G), DVD-R multiborders, DVD+R, DVD+R multi-sessions, DVD-RW and DVD+RW
CD: CD-DA, CD-ROM, CD-ROM/XA, Photo-CD, Multi-session, Karaoke-CD,
Video-CD, CD-I FMV, CD Extra, CD Plus, CD-R, CD-RW
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Eject Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
Specification
Audio Controller
Realtek ALC202
Audio onboard or optional
Built-in
Chapter 1
25
Audio Interface
Item
Specification
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to analog converter
18 bit stereo Analog to Ditial converter
Compatibility
AC97
Mixed sound source
Line-in, CD
Voice channel
8/16-bit, mono/stereo
Sampling rate
44,1 KHz (48K byte for AC97 interface)
Internal microphone
Yes
Internal speaker / Quantity
Yes/2
Supports PnP IRQ
IRQ10
Speakers
Item
Specification
Number of speaker
2
Rating
1W, max; 4 ohm
Connector type
Headphone out, microphone in and line-in
Video Interface
Item
Specification
Chipset
ATI M9+X
Package Specifications
Package, Size: 650 BGA, 31mm x 31mm
Supports ZV (Zoomed Video) port
No
Resolution Support
Max 2D/3D resolution: 2048x1536
Max color depth: 16.7M Colors
LVDS, TMDS, TV-out: 2048x1536, 1600x1200, 1024x768
Bus Specifications
AGP bus support / PCI bus support: AGP 2X (3.3V) / 4X (1.5V) /
PCI 2.2
Memory Type
Samsung 4MBx32 DDR SDRAM
VGA Ram Size
128MB
Parallel Port
Item
26
Specification
Parallel port controller
PC87393
Number of parallel port
1
Location
Rear side
Connector type
25-pin D-SUB
Parallel port function control
Enable/Disable/Auto (BIOS or operating system chooses
configuration) by BIOS Setup
Note: Depending on your operating system, disabling an unused
device may help free system resources for other devices.
Supports ECP/EPP/Bi-directional/Output only
(PS/2 compatible)
Yes (set by BIOS setup)
Note: When Mode is selected as EPP mode, “3BCh” will not be
available.
Optional ECP DMA channel (in BIOS Setup)
DMA channel 3
Optional parallel port I/O address (in BIOS
Setup)
378h, 278h, 3BCH
Chapter 1
Parallel Port
Item
Optional parallel port IRQ (in BIOS Setup)
Specification
IRQ7, IRQ5
USB Port
Item
Specification
Chipset
VIA VT8235
USB Compliancy Level
2.0
OHCI
USB 2.0
Number of USB port
4
Location
Left side
Serial port function control
Enable/Disable by BIOS Setup
IEEE 1394 Port
Item
Specification
Chipset
TI TSB43AB21
Interface USB Compliancy Level
IEEE 1394 1.0
Number of IEEE 1394 port
1
Location
Left side
Connector type
IEEE 1394
PCMCIA Port
Item
Specification
PCMCIA controller
TI PCI1410
Supports card type
Type-II
Number of slots
One type-II
Access location
Left panel
Supports ZV (Zoomed Video) port
No ZV support
Supports 32 bit CardBus
Yes (IRQ10)
Smart Card Reader
Item
Specification
Chipset
PCMCIA chip built-in
Number of slot
1
Location
Front side
System Board Major Chips
Item
Controller
Core logic
VIA KN400 (AMD AthlonTM XP-M processor, VIA KN400+VIA
VT8235)
VGA
ATI M9+X
LAN
VIA VT8235 embedded LAN controller + VT6103 LAN PHYceiver
IEEE 1394
TI TSB43AB21
USB 2.0
VIA VT8235 embedded USB controller
Chapter 1
27
System Board Major Chips
Item
Controller
Super I/O controller
NS PC87393
MODEM
South bridge/VIA VT8235
Blue tooth
South bridge/VIA VT8235
Wireless 802.11g
BCM4306KFB
PCMCIA
TI PCI1410
Audio
RealTek ALC202
Four-in-one card reader
M220V0315
Touchpad
Synaptics TM41P-353
IR
Vishay TFU6102F
Keyboard
Item
Specification
Keyboard controller
NS 87570 C4
Keyboard vendor & model name
DARFON
Total number of keypads
84/85 key
Windows logo key
Yes
Internal & external keyboard work
simultaneously
No
Note: Internal and external keyboard can not work
simultaneously by software specification.
Battery
Item
Specification
Vendor & model name
Simplo/Sanyo
Battery Type
Li-ion
Pack capacity
4400 Ah
Cell voltage
3.7V/cell
Number of battery cell
8
Package configuration
4 cells in series, 2 series in parallel
Package voltage
14.8V
LCD
Item
Vendor & model name
AU B150XG01
HITACHI TX38D81VC
LG LP150X08
LCD display area
(diagonal, inch)
15.0
15.0
15.0
Display technology
TFT
TFT
TFT
Resolution
XGA (1024x768)
XGA (1024x768)
XGA (1024x768)
Supports colors
262K
262K
262K
Contrast ratio
300
100
175 (Min.) 250 (Typ.)
Response time(msec)
Rising: 24 (Typ.) 15
(Max.)
Falling: 11 (Typ.) 30
(Max.)
Rising: 30 (Typ.) 50
(Max.)
Falling: 30 (Typ.) 50
(Max.)
Rising: 10 (Typ.) 20
(Max.)
Falling: 20 (Typ.) 30
(Max.)
Mechanical Specifications
Optical Specification
28
Chapter 1
LCD
Item
180 (5 points average)
180 (5 points average)
150 (5 points average)
Brightness control
keyboard hotkey
keyboard hotkey
keyboard hotkey
Contrast control
No
No
No
3.3
3.3
3.3
Limuinance, white, 5P
(cd/m2)
Electrical Specification
Supply voltage for LCD
display (V)
AC Adaptor
Item
Specification
Model number
LITE- ON PA-1900-05QA, 3pins
LSE 0202C1990, 3pins
Input rating
90VAC to 264VAC, 47Hz to 63Hz
Output rating
75W, 19V (18.8V, min to 20V, max), 4A (0A, min to 4A, max)
System Power Management
ACPI mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be power
managed in this state.
Suspend to RAM (S3)
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4)
Also called Hibernate state. System saves all system states and
data onto the disk prior to power off the whole system.
Memory Address Map
Memory Address
00100000h-000F0000h
Size
Function
512 KB
System BIOS
000CFFFFh-000C0000h
00009FFFFh-00000000h
VGA BIOS
640KB
Conventional memory
I/O Address Map
I/O Address
Function
000-00F
DMA controller-1
020-021
Interrupt controller-1
040-043
Timer 1
060, 064
Keyboard controller 87570 chip select
061
System speaker
Chapter 1
29
I/O Address Map
I/O Address
Function
000-00F
DMA controller-1
020-021
Interrupt controller-1
040-043
Timer 1
060, 064
Keyboard controller NS87591 chip select
070-073
Real-time clock and CMOS
0A0-0A1
Interrupt controller-2
0C0-0DF
DMA controller-2
066, 062
ACPI EC interface (NS87591)
170-177
Secondary IDE channel
1F0-1F7
Primary IDE channel
378, 37F
Parallel port
3B0-3BB
VGA I/O adress
3C0-3DF
CF8-CFF
PCI configuration register
000-00F
DMA controller-1
IRQ Assignment Map
Interrupt Channel
IRQ00
Function(Hardware)
System timer
IRQ01
Keyboard
IRQ02
Programmable interrupt controller
IRQ03
IrDA Fast Infrared Port
IRQ04
Communication port (COM1)
IRQ05
Winbond SD controller
IRQ06
Standard floppy disk controller
IRQ07
ECP printer port (LPT1)
IRQ08
CMOS/RTC
IRQ09
SCI IRQ used by ACPI bus
IRQ12
PS/2 mouse
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
DMA Channel Assignment
Item
30
Specification
Channel 1
IrDA Fast Infrared Port
Channel 3
ECP printer port
Channel 4
DMA controller
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. Press <F12> during POST to enter multi-boot menu. In this menu, user can change
boot device without entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Security
Boot
CPU Type:
CPU Speed:
AMD Athlon XP-M
IDE1 Model Name:
IDE1 Serial Number:
None
None
System BIOS Ver:
Ferrari 3000_V1.00
VGA BIOS Ver:
KBC Ver:
Serial Number:
AT M7-P V0.2
V1.00
xxxxxxxxxxxxxxxxxxxxxx
Asset Tag Number:
Product Name:
N/A
Ferrari 3000
32 Byte
Manufacturer Name:
UUID:
Acer
xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
16 Byte
16 Byte
F1 Help
↑ ↓
Esc Exit
←→
Chapter 2
Exit
22 Byte
16 Byte
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
31
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press por q.
T
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
This menu provides you the information of the system.
32
Chapter 2
Info.
PhoenixBIOS Setup Utility
Information
Main
CPU Type:
Advanced
Security
Boot
Exit
AMD Athlon XP-M
CPU Speed:
IDE1 Model Name:
None
IDE1 Serial Number:
None
System BIOS Ver:
Ferrari 3000_V1.00
VGA BIOS Ver:
KBC Ver:
Serial Number:
AT M7-P V0.2
V1.00
xxxxxxxxxxxxxxxxxxxxxx
Asset Tag Number:
Product Name:
N/A
Ferrari 3000
32 Byte
Manufacturer Name:
UUID:
Acer
xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
16 Byte
16 Byte
22 Byte
16 Byte
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Parameter
Description
Serial Number
This field displays the serial number of this unit.
UUID Number
UUID=32bytes
Chapter 2
33
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Item Specific Help
System Time:
[00:00:00]
System Date:
[10/15/2003]
System Memory:
640 KB
Extended Memory:
238 MB Shows extended memory size
VGA Memory:
128MB
Quiet Boot:
[Enabled]
Power on display:
[Auto ]
LCD Auto Dim:
[Enabled]
Wakeup from LAN
[Disabled]
F12 Boot Menu
[Disabled]
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system memory size
VGA memory size
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
NOTE: The screen above is for reference only. Actual values may differ.
34
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
Video Memory
Shows the VGA memory size. The default value
is set to 32MB
Option:32/64MB
Quiet Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Auto or Both
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
LCD Auto Dim
Determines if the system will automatically dim
the LCD brightness in order to save power when
AC is not present.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
35
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Parallel port:
Mode:
Base I/O address:
Interrupt:
DMA channel
Security
[Enabled]
[Bi-direct]
[378]
[IRQ 7]
[DMA3]
Boot
Exit
Item Specific Help
Configure Infrared Port
using options:
[Auto]
Disable the touchpad if an
external PS/2 mouse is
connected. Otherwise
enable the touchpad
[Both]
The touchpad is always
enabled. Any external PS/2
mouse connected will be
enabled at the same time.
F1
Help
Esc Exit
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
36
Description
Options
Serial Port
Enables, disables or auto detects the serial port.
Enabled/Disabled/Auto
Parallel Port
Enables, disables or auto detects the parallel port.
Enabled/Disabled/Auto
Mode
Sets the operation mode of the parallel port.
ECP, EPP, Normal or Bi-directional
Base I/O address
Sets the I/O address of the parallel port. This
parameter is enabled only if Mode is set to ECP or
Bi-directional. This parameter is enabled only if
Mode is set to ECP.
378h/278h/3BCH
Interrupt
Sets the interrupt request of the parallel port.
IRQ7/IRQ5
DMA channel
Sets a DMA channel for the printer to operate in
ECP mode. This parameter is enabled only if Mode
is set to ECP.
DMA3/DMA1
Chapter 2
Parameter
Description
Options
Internal Touchpad
Determines whether or not to disable the internal
pointing device as the PS/2 mouse is connected.
Both or Auto
Infrared Port (FIR)
Enables, disables or auto detects the infrared port.
Disabled/EnabledDisabled/Auto
Chapter 2
37
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Item Specific Help
User Password is
Supervisor Password is
Clear
Primary HardDisk Security
Clear
Set User Password
[Enter]
Set Supervisor Password
Set HDD Password
[Enter]
[Enter]
Password on boot:
[Enabled]
F1
Help
Esc Exit
38
Clear
↑ ↓
←→
Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password is
Shows the setting of the uer password.
Clear or Set
Supervisor Password is
Shows the setting of the Supervisor password
Clear or Set
Primary Harddisk Security
This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Set User Password
Press Enter to set the user password. When
set, this password protects the BIOS Setup
Utility from unauthorized access.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access.
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
39
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
40
Chapter 2
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2
41
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Item Specific Help
+Hard Drive
Keys used to view or configure
devices: <Enter> expnads or
Collapses Devices with a
+ or <Ctrl+Enter> expnads all
<Shift + 1> enables or disables
a device.
<+> and <-> moves the device
up or down.
<n> May move removable
device between Hard Disk or
Removable Disk.
<d> Remove a device that is
not installed.
+Floppy Devices
CD-ROM Drive
Boot to LAN
F1
Help
Esc Exit
42
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Information
Main
Advanced
Security
Boot
Exit
Item Specific Help
Exit Saving Changes
Exit System Setup and
save your changes to
CMOS.
Exit Discarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4Sub- Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
43
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the Phlash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
System Diagnostic Diskette
This diagnostic diskette is for the Acer Aspire 1450 series notebook machine. However, system diagnostic
utility is not ready as service CD released. Acer HQ CSD will upload the utility to CSD website as soon as it is
ready.
44
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screw driver
T
Flat head screwdriver
T
Plastic flat head screw driver
T
Hex screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
45
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3. Remove the battery pack.
NOTE: Ferrari 3000 series product uses mylar or tape to fasten the FFC/FPC/connectors/cable, you may
need to tear the tape or mylar before you disconnect different FFC/FPC/connectors.
46
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
Hx2
Hx2
HDD Door
Dimm Door
HDD Module
Memory
Hx2
Ox4
Middle Cover
Hx2
Mx3
Keyboard
PCI Door
Sx4
Hx3
LCD Module
Wireless LAN
Card
Function Key
Board
Main Unit
Assembly
ODD Module
Fx2
Cx4
ODD Bracket
ODD Board
ODD
Front Bezel
Sx19
Hx2
Ux3
Logic Upper
Assembly
Logic Lower
Assembly
Ax4
Hx1
Hx1
Qx4
Touchpad
Shielding
Main Board
Touchpad
Board
Dx3
Hx4
Touchpad
Holder
Tx2
CPU
Touchpad
Fx2
4-in-1 Card
Rearder
Dimm
HDD
Bracket
Hx2
Modem/
Bluetooth
Combo Card
Top Cover
Shielding
Ex4
Thermal
Module
Touchpad
Cable (FFC)
Antenna Line
Chapter 3
Hx1
Smart Card
Reader
Modem Cable
47
LCD Module
6 LCD
Cushions
Jx6
LCD Bezel
LCD Inverter
Hx4
LCD
Assembly
LCD Panel
Hx4
Hx2
Dx4
LCD
LCD Coaxial
Cable
LCD Brackets
Wireless
Antenna
LCD Latch Kit
Bracket
Dx1
LCD Latch Kit
Screw List
Item
48
Description
A
NUT-I/O
B
SCREW M1.6X4.0-I-NI-NYLOK
C
SCREW M2.0X2.5-I-NI-NYLOK
D
SCREW M2.0X3.0-I-NI-NYLOK
E
SCREW M2.0X3.5-I-NI-NYLOK
F
SCREW M2.0X5-I-NI-NYLOK
G
SCREW M2.5X3-I-NI-NYLOK
H
SCREW M2.5X4.0-B-NI-NYLOK
I
SCREW M2.5X4-I-NYLOK
J
SCREW M2.5X5.0-I-NI-NYLOK
K
SCREW M2.5X5.5-P-NI-NYLOK
Chapter 3
Item
Description
L
SCREW M2.5X0.45+7I-NYLOK
M
SCREW M1.7X3.5-I-BZN
N
SCREW M2X3-I-BNI-NYLOK
O
SCREW M2.0X5.0-I-BNI-NYLOK
P
SCREW M2.0X6.0-I-NI-NYLOK
Q
SCREW M2.5X2-I-NI-NYLOK
R
SCREW M2.5X4-I-BNI
S
SCREW M2.5X7
T
SCREW M3.0X3.5
U
SCREW M2.5X5 (BLACK)
Chapter 3
49
Removing the Battery Pack
50
1.
Release the battery lock.
2.
Slide the battery latch then remove the battery.
Chapter 3
Removing the Optical Module/HDD Module/Wireless Lan Card and LCD
module
Removing the Optical Module
1.
Slide the optical disk drive latch.
2.
Remove the ODD module.
Removing the HDD Module
1.
Remove the two screws holding the HDD cover.
2.
Remove the HDD cover.
3.
Remove the HDD module.
Removing the Wireless LAN Card
1.
Remove the screw that secures the PCI door then remove the PCI door.
2.
Disconnect the right and the left wireless antenna.
3.
Pop out the wireless LAN card then remove it.
Chapter 3
51
Removing the LCD Module
52
1.
Remove the four screws that secures the middle cover; two one each side.
2.
Detach middle cover with the assistance of a plastic flat head screw driver.
3.
Disconnect the LCD cable then take out the cable from the upper case.
4.
Disconnect the left wireless LAN antenna line. Then take out the antenna from the upper case with a
tweezers.
5.
Unscrew the four screws holding the LCD hinges; two on each side.
6.
Then remove the entire LCD module.
Chapter 3
Disassembling the Main Unit
Remove the function key board and the keyboard
1.
Take the wireless antenna out of the hook on the function key board.
2.
Disconnect function key board connector
3.
Unscrew the three screws holding the function key board.
4.
Remove the three screws that secure the keyboard.
5.
Turn over the unit and remove the two screws as the picture shows.
6.
Turn over the keyboard. Disconnect the keyboard FFC then remove the keyboard.
Separate the main unit into the logic upper and the logic lower assembly
1.
Remove the three screws on the rear panel.
2.
Unscrew the 19 screws on the bottom panel.
3.
Detach the front bezel from the main unit.
4.
Remove the two screws. Then take the right and the left antenna off the main unit.
5.
Disconnect the touchpad cable.
6.
Pull out the right and the left wireless LAN antenna, then detach the logic upper assembly from the logic
lower assembly.
Chapter 3
53
Disassembling the logic upper assembly
54
1.
Take out the touchpad cable from the small hook on touchpad holder.
2.
Remove the four screws holding the touchpad shielding and the touchpad board.
3.
Disconnect the touchpad FFC from the touchpad board.
4.
Remove the touchpad board.
5.
Remove the wireless and bluetooth button off the touchpad board.
6.
Remove the four screws that fasten the touchpad holder.
7.
Remove the touchpad off the logic upper assembly.
8.
Disconnect touchpad FFC.
Chapter 3
Disassembling the logic lower assembly
1.
In order to take out the main board from the upper case, first remove the four screws that fasten the top
cover shielding.
2.
Remove the three screws holding the 4-in-1 card reader, then remove it.
3.
Unscrew the four screws that secure the thermal module.
4.
Disconnect the fan connector then remove the thermal module.
5.
Remove one screw that secures the main board as picture shows.
6.
Remove another screw that fastens the main board.
7.
Take out the bluetooth antenna.
8.
Disconnect the speaker set cable.
9.
To remove the main board from the lower case assembly, first press the PCMCIA card button.
10. Then take the main board off the lower case assembly.
11. Unscrew the two screws that fasten the HDD bracket.
12. Remove one screw holding the top cover shielding.
Chapter 3
55
13. Disconnect the microphone cable. Then remove the top cover shielding.
14. Use a flat-headed screw driver to release the CPU then remove the CPU from CPU socket.
15. Put the CPU back to the socket, then lock the CPU to the socket with as flat-headed screw driver.
NOTE: If you use an ordinary flat-headed screw driver to remove the CPU. Please be very careful to prevent
any damage.
16. Pop out the memory then remove it.
17. Unscrew the two screws that secure the modem/bluetooth combo card. Remove the modem/bluetooth
combo card then disconnect the connector.
18. Disconnect the bluetooth antenna and the modem cable.
19. Disconnect the smart card reader FPC.
20. Unscrew the two screws holding the smart card reader then remove it.
56
Chapter 3
Disassembling the LCD Module
1.
Remove the six screw pad and the six screws.
2.
Detach the LCD bezel carefully.
3.
Disconnect LCD inverter.
4.
Remove the two screws holding the LCD to LCD panel.
5.
Then remove the LCD.
6.
Remove the four screws that fasten the right and the left LCD brackets. Then remove the right and the left
LCD brackets.
7.
Tear off the electric conductive tape that fastens the LCD coaxial cable.
8.
Tear off another electric conductive tape that fastens the LCD coaxial cable.
9.
Disconnect the LCD coaxial cable.
.
10. Detach the wireless antenna from the LCD panel.
11. Remove the two screws holding the LCD latch kit.
12. Remove the LCD latch kit bracket.
Chapter 3
57
13. Unhook the spring.
14. Remove the screw that fastens the LCD latch kit.
15. Then remove the LCD latch kit.
58
Chapter 3
Disassembling the External Modules
Disassembling the HDD Module
1.
Remove the four screws holding the HDD bracket; two on each side.
2.
Take out the HDD from the HDD bracket.
Disassembling the Optical Drive Module
1.
Remove the two screws holding the ODD bracket.
2.
Remove another screw as the picture shows.
3.
Then remove the last two screws on the back side of the ODD module.
4.
Slide the ODD from the ODD bracket.
5.
Then remove the optical bracket.
6.
In order to open the ODD, use an uncurved pin to press the emergency eject hole.
7.
Remove the three screws that fasten the ODD door.
8.
Then detach the ODD door.
Chapter 3
59
60
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model. Non-Acer products, prototype cards, or modified
options can give false errors and invalid system responses.
1.
Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.
Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic
test or by repeating the same operation.
3.
Disassemble and assemble the unit without any power sources.
4.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 63.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 65
“Undetermined Problems” on page 77
POST detects an error and displayed messages
on screen.
“Error Message List” on page 66
The diagnostic test detected an error and
displayed a FRU code.
“System Diagnostic Diskette” on page 44
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 65
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 65
“Intermittent Problems” on page 76
“Undetermined Problems” on page 77
Chapter 4
61
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device. See “System Diagnostic Diskette” on page 44 for details.
1.
Boot from the diagnostics diskette and start the diagnostics program (see “System Diagnostic Diskette” on
page 44).
2.
See if FDD Test is passed as the program runs to FDD Test.
3.
Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program (refer to “System Diagnostic
Diskette” on page 44.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test. See “System Diagnostic Diskette” on page
44 for details.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
62
Numeric keypad
Chapter 4
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
Chapter 4
“Check the Battery Pack” on page 64
63
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the the PS/2 mouse does not work, then check if the main board to switch board FPC is connected O.K.
4.
If the main board to switch board FPC is connected well, then check if the FCC on touch pad PCB
connects properly.
5.
If the FFC on touch pad PCB connects properly, then check if LS851 JP1 Pin6=5V are pulese. If yes, then
replace switch board. If no, then go to next step.
6.
Replace touch pad PCB.
7.
If the touch pad still does not work, then replace FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
64
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 77.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
65
Index of Error Messages
Error Message List
Error Messages
FRU/Action in Sequence
Struck Key
See ““Keyboard or Auxiliary Input Device Check” on page 62
System CMOS checksum bad - Default
configuration used
RTC battery
Real time clock error
Run BIOS Setup Utility to reconfigure system, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
Previous boot incomplete - Default configuration
used
“Load Default Settings” in BIOS Setup Utility.
RTC batter
Main baord.
Invalid System Configuration Data
“Load Default Settings” in BIOS Setup Utility.
Main board.
Operating system not found
Enter Setup and see if fixed disk and drive A are properly identified.
Dikette drive
Hard disk drive
Main board.
66
Chapter 4
Error Message List
No beep Error Messages
Power-on indicator turns off and LCD is blank.
FRU/Action in Sequence
Power source (battery pack and power adapter.) See “Power
System Check” on page 63
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
Main board.
Power-on indicator turns on and LCD is blank.
Power source (battery pack and power adapter.) See “Power
System Check” on page 63
Reconnect the LCD connector
Hard disk drive
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and LCD is blank.
But you can see POST on an external CRT.
Reconnect the LCD connectors.
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and a blinking cursor
shown on LCD during POST.
Chapter 4
Ensure every connector is connected tightly and correctly.
Main board
67
POST Codes
Code
Beeps
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
22h
1-3-1-3
Test DRAM refresh
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
46h
68
POST Routine Description
02h
POST device initialization
2-1-2-3
Check ROM copyright notice
Chapter 4
Code
Beeps
POST Routine Description
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
58h
59h
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
Chapter 4
69
Code
Beeps
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
B4h
70
POST Routine Description
POST done- prepare to boot operating system
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Chapter 4
Code
Beeps
For Boot Block in Flash ROM
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
F4h
Initialize System Management Mode
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
71
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
First, plug a monitor to CRT port. Next, enter BIOS utility to running
“Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
LCD is too dark
LCD brightness cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Reconnect the LCD cable
Missing pels in characters
LCD cable
Abnormal screen
LCD
Wrong color displayed
Main board
LCD has extra horizontal or vertical lines
displayed.
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but system
runs correctly
Main board
HDD/CD-ROM active indicators cannot work
HDD/CD-ROM drive
Device driver
Main board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 63.
Battery pack
AC adapter
See if the thermal module is overheat (Heat sink or fan).
Main board
The system cannot power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 63.
Battery pack
Power adapter
CPU
Main board
The system cannot power-off.
In Windows XP operating system, hold and press the power switch
for more than 4 seconds. If the system can power off, then the main
board is OK. Verify OS in the HDD.
Main board
72
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged or discharged
Action in Sequence
See “Check the Battery Pack” on page 64.
Battery pack
Main board
System hang during POST
ODD/HDD/FDD/RAM module
Main board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
PC Card cannot be inserted or ejected
Check if the PCMCIA slot is blocked
Main board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot system.
RAM module
Main board
Check BIOS revision
System can power on, but you hear two long
beeps: “B--, B--” and the LCD is blank.
Reinsert DIMM
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
OS volume control
Audio driver
Speaker
Main board
Internal speakers make noise or emit no sound.
Speaker
Main board
Microphone cannot work
Audio driver
Volume control in Windows XP
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation mode
Action in Sequence
Power option in Windows XP
Hard disk drive
Main board
The system doesn’t enter standby mode after
closing the lid of the portable computer.
Driver of Power Option Properties
Lid close switch in upper case
Main board
Chapter 4
73
Power Management-Related Symptoms
Symptom / Error
The system doesn't resume from hibernation/
standby mode.
Action in Sequence
Connect AC adapter then check if the system resumes from
Standby/Hibernation mode.
Check if the battery is low.
Hard disk drive
Main board
The system doesn't resume from standby mode
after opening the lid of the portable computer.
LCD cover switch
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Refresh battery (continue use battery until power off, then charge
battery).
Main board
Battery pack
Main board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Main board
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the
installed devices.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then
reboot system.
Reconnect hard disk/CD-ROM drives/FDD or other peripherals.
Main board
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Keyboard
Main board
USB does not work correctly
See “System Diagnostic Diskette” on page 44
Main board
Print problems.
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Run printer self-test.
Printer driver
Printer cable
Printer
Main board
Parallel port device problems
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Device driver
Device cable
Device
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
Main board
74
Chapter 4
Modem/LAN-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
See “System Diagnostic Diskette” on page 44.
Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Internal LAN does not work correctly
Lan cable
Driver
Main board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 77.
Chapter 4
75
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
76
1.
Run the diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 63):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
T
System board
T
LCD assembly
77
78
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
3
2
PD1
PC1
PD2
PR1
PQ1
HOLE15
R591
R594
PC5
L18
C4
L19
C5
C6
L20
C7
L21
C8
C9
L22
C10
C29
R34
R33
CN5
7
H
PR11
PR3
PR4
RP3
3
U4
HOLE21
PR15
PC15
PR14
PC17
PR5
PC6
2
CN6
PR6
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
L17
L15
R584
L16
R26
L11
L12
L13
L14
R25
R583
R24
R28
C21
C20
C19
C22
C24
C25
C26
R27
L6
L7
L8
L9
L10
HOLE8
L1
R1
L2
L3
L5
PQ36
C32
PR7
PR9
PR12
R592
PC16
PR17
PC23
PR16
PQ4
PQ53
PQ6
HOLE24
PR31
PU2
PR30
PR35
C50
L37
PC32
PR36
PC36
C91
PC42
PR42
PQ10
PQ11
PR43
PR44
PR45
PR46
PR47
PU4
47 49
C170
PC43
4
G
PC152
C178
3
C207
R135
G
HOLE35
C152
C153
C154
I
R123
C188
C190
R125
10
PQ21
O
G
I
I
O
R120
CN15
PQ12
PR41
PQ9
PU12
O
CN18
PQ23
T33
PR138
O
G I
O
G
PR139
PC44
PC45
C220
PL8
9
R116
C163
11
PQ52
PQ51
PC60
HOLE40
C278
R593
R601
R179
C322
C323
PR77
C333
R232
PC69
PR78
PC70
PL10
PL11
PC72
PC74
PC75
PR79
PC76
C277
C283
C292
C300
C305
C318
12
C327
PD9
HOLE41
C308
R192
R197
R199
C325
5
PQ31
PQ29
PC52
PR63
L42
L43
L44
PC151
C184 C185
R121 R122
PR53
L46
PR61
PR57
PQ17
PQ22
PC59
PR64
PR65
PQ26
PC63
C268
C269
C281
C90
PC37
PQ7
PR40
RP28
RP27
RP26
RP30
C127
RP29
C111
C112
C113
C114
C115
Q16
PQ18
PU6
PL9
G
R186
C986
C293
C301
D11
PQ28
PC65
C306
C307
C264
C270
C285 C267
D12
C266
C294
GI
I
PQ15
PR59
PC62
CN19
PC73
PC71
PQ34
PR80
PC77
C314
C315
C313
C316
C312
C317
C319
C272
R597
PR67
PR71
PQ24
PR73
PR62
PR66
PR68
PC55
PR72
O
O
20
PL6
O
G
PR51
I
PR55
PQ20
PC47
PR60
PQ19
PU7
C262
C274
C282
C287
C296
C299
C311
C303
C298
M 1 2 4 8
1 2 3
0 1 2 4 8
L D E F GH
I J K L
S D MN
D1
I
D2
Q18
R263
44
PR147
PC7
PC20
PR8
PC12
PC14
PC2
CN30
PC4
PC10
A
A
19
C218
PR56
PR58
PD10
PD11
G
G
Q49
O
G
I
CN20
PR2
C30
R35
HOLE26
C47
D C B A
H G F E
L K J
C126
5
2
CN29
4
C372
R279
C380
R295
R296
HOLE52
8
U15
CPAD4
CPAD3
CPAD2
HOLE53
CPAD1
SW1
3
R298
C377
C378
DA0ZI3MB6D7 REV:D
HOLE48
2
4
M
N
R P
U T
Y W V
AC
C123
C122
C151
C120
C119
C121
C104
C149
C148
C150
C147
C146
C145
PAD31
PL19
PC150
PL21
PC153
HOLE45
C381
C382
PR21
C125
PQ25
PR75
C320
R211
R588
R250
PC66
R293
Q20
C383
PC48
PC49
PC54
C275
C276
PQ30
R200
R201
C321
PC67
C288
C297
R234
C340
R242
R598
R596
R222
R223
C230
Q21
D14
Q19
GI
HOLE51
10
AA
AB
AD
AE
AF
RP25
RP24
RP23
RP22
RP19
RP20
RP21
RP33
RP16
RP17
RP18
RP32
RP31
C116
C143
C144
C141
C142
C108
C109
C110
C140
C139
R113
C134
C135
C136
C137
C138
C124
PC53
PQ27
R202
RP44
R219
R217
R218
C364
O
G
9
8
L31
PC26
PC28
L32
PR24
PR25
PC27
PR26
PR27
PR28
C34
AA
AB
AC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
E
E
PD8
PC61
G
8 14 13
15
HOLE29
I
R595
RP50
R602
PR33
PL4
C83
PR70
F
F
PC21
16
PC31
C
C
PQ14
PR69
O
HOLE50
PR52
PR54
PD7
PC56
T55
C363
L48
I
PC25
PR29
PR32
C44
AD
AE
AF
RP15
RP14
RP12
RP13
RP11
C107
R104
RP10
PC50
C252
C253
PR76
R176
R177
C261
HOLE37
10
C210
R152
C223
O
C373
L4
D8
U3
U2
C28
PC24
PR23
PR144
18
19
20
21
22
23
24
25
26
17
12
13
14
15
16
T1
T2
11
9
6
8 T3
1
2
3
4
5
7
B
D
E
L34
H G F
J
C46
K
R P N ML
C73
U T
Y W V
C74
PR37
C988
34
68
RP36
C249
C250
RP42
11
R229
R230
R231
RP47
C225
R158
R159
R160
R161
C226
C227
C228
C229
RP46
T54
T56
C235
D13
R286
R287
HOLE22
CN16
C193
C194
C195
C196
C197
25
CN17
PL5
R215
C331
R224
R268
R270
R272
R288
C375
PAD47
R289
R292
R297
R283
C379
R281
R282
R278
R284
R285
C374
R274
R277
R291
R294
PAD46
PR38
D10
C81 C77
C82 C78
C53
D9
C51
R79
R80
C79
C80
R114
C202
C203
C204
C205
R167
R168
R169
T34
C256
T36
C302
T44
C339
C344
C345
L56
C980
R260
R226
R227
R228 R245
R246
R247
R259
C367
RP48
C371
R267
R290
R276
C234
T57
C370
R271
L63
C981
PR18
PR19
PR20
PU1
PQ3
R124
RP45
R240
C368
R266
CN21
C87 R82
R83 C84
C85
C55
U8
R76
R86
R87
R88
R89
R90
R91
R94
R95
R96
R97
R98
R99
T14
T13
T16
T19
C93
T20
T18
C162
R118
C989
C174
L45
C200
C201
R127
AF
AG
AH
AJ
AK
AC
AD
AE
C164
C172
Y1
L47
C224
RP37
C248
T43
R256
C365
C291
R180
R189
L53
C336
C334
C335
L54
R237
R238
R239
C358
C360
C361
L55
R236
C342
C346
C351
C352
R235
C341
R243
C350
R249
C105
1
PC64
R241
PC3
C27
PQ44
41
Q17
R233
C338
R599
R600
Q7
H
CN2
C409
Q8
Q15
PC114
HOLE4
HOLE6
PAD9
C408
2
O
Q10
PR82
HOLE3
PL1
PR99
200
R187
R191
C265
T45
T47
6
R29
Q4
PQ54
PL3
42
40
20
PC57
I
Q5 Q6
PD3
20
PR148
G
HOLE2
HOLE7
PAD57
CN8
19
O
G
PC93
PQ13
PC58
T41
T42
T48
C369
R265
R273
C118
E
E
PAD34
PQ16
PQ32
R178
R181
RP43
R193
C347
PAD43
R280
L61
L62
R173
R174
RP41
C271
R261
R269
L59
L60
R275
R170
CN3
R585
PQ2
PR10
8
HOLE36
G
Q3
PC9 PR13
C117
39
C259
C343
R244
C348
R214
G
G
I
L28
HOLE17
199
PC51
R165
R262
R264
2
R101
R103
R107
R109
R111
R115
R128
F
RP38
C247
Q50
C254
R175
L49
C260
T35
C245
C240
C241
R172
U14
R221
T50
R257
R258
T96
T40
C354
C357
R117
R119
R188
T46
R253
R255
35
U11
T37
C279
R603
C309 R203
C310 C329
C324
R213
R216
R251
PAD42
T53
T49
T51
L58
R252
C355
C359
C356
R605
PC41
R110
RP39
C263 C273
C257
T52
C330
R220
R225
R248
C362
C332
C221
C233
R171
C251
R182
C289
R183
C304
C993
R210
T39
L51
L52
C337
C349
L57
C353
C255
C295
R194
R190
R196
R198
R184
R195
U12
C280
C286
C290
T38
R185
U13
C244
C246
C242
R166
C243
R207
R208
R209
R204
R205
R206
R212
C328
PR39
CON1
PL7
C216
C219
R150
R154
R156
C222
C231
C236
65
64
32
33
HOLE38
C326
L50
PU3
HOLE30
O
Q48
R100
R102
R106
D
D
PC46
R153
R155
R157
C992
I
G
R65
PC34
R151
C232
R162
R163
C237
R164
C238
C239
C176
C158
C159
C160
C168
R141
R149
C192
R140
C217
R148
C284 RP40
97
128
Y2
96
T31
T32
C215
C198
C199
C974
C975
R126
C191
C973
R138
T24
U10
T22
T23
R137
R139
R142
L35
C57
R69
R73
R70
R68
C56
C59
R67
G
D
E
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
C171
C211
R143
R144
R145
R146
R147
C212
C213
C214
C209
T28
T29
T27
T30
R136
RP34
C972
C173
C967
C208
C181
C183
C187
C189
C186
T21
C131
C366
C161
C156
C177
C182
T26
T25
C130
C179
U9
H
J
F
A
B
C
C102
3
2
1
C128
C965
C129
R92
R93 C94
C96 C92
C103
L41
C100
R108
R112
R64
R66
R74
C984
C64
C89
C95
C258
C101
C106
C60
9
8
7
6
5
4
C45
R71
L36
PQ8
T17
10
C132
RP35
C133
C98
C99
C964
R85
C157
L39
4
4
1
1
15
14
13
12
11
T15
C963
C97
D
D
PC38
PC39
PC40
R84
T6
R63
T8
R77
R78
C86
C88
RP49
RP9
L40
U6
R81
C166
C167
C169
4 3 2
CN14
RP8
3
3
2
2
C961
C962
C48
C49 C
C
C52
C63
C62
L38 PC33
PC35
R75
C70
C75
C376
C72
C76
C54
R72
T10
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
R134
C206
R129
R130
R131
R132
R133
C966
C175
C69
C71
T12
T11
C65
C67
C68
C66
C960
HOLE28
C58
15
R60
2
1
N
C
C61
R56
R57
C38
C39
R62
R61
C165
3
C180
4
C
C42
3
2
L33
1
R30
R31
HOLE14
40
PL2
T5
A
R58
T4
R59
16
10
C40
C41
C37 R55 C35 C36
U7
C43
HOLE25
HOLE23
PAD10
10
2
3
R54
RP2
39
CN7
PD6
C33
R53
L30
1
4
CN13
RP1
O
C155
L29
R51
R52
CN11
2
11
R48
R50
HOLE20
C18
36 34 32 30 28 26 24
29 27 25 23
37 35 33 31
R46
R47
3
C16
L26
6
8
4
2
22 20 18 16 14 12 10
9
15 13 11
7
5
3
1
21 19 17
R40
Q13
Q11
R43
R44
2
R49
R587
Q14
R45
1
4
1 14 2 15 3 16 4 17 5 18 6 19 7 20 8 21 9 22 10 23 11 24 25
13
12
CN4
U5
C426
I
C427
O G
I D6
B
B
HOLE16
Q12
L27
CN10
R38
R39
R41
R42
B
B
5
O G
R12
I
RP7
1
3
RP5
RP6
2
R36
RP4
C31
R37
Q9
R32
C23
1
4
4
3
A
A
O G
PC30
PR34
PC29
2
D1
HOLE11
C1
L24
C2
C3
L25
O
AN
AM
AL
C12
AK
AJ
AH R5
AG
AF D2
AE
AD
AC
AB
AA
Z
D3
Y
X
W
V
U
R7
T
Q2
6
G D4
20
3
GI
R3
2 7
C13 R6
PAD13
CN9
I
F
E D5
D R10
C
B
A
R11
D7
5
S
C14
R
Q
P
N
M
L
C15
K
J R8
H
R9
G
9
Q1
4
L23
OG
U1
I
8
O
CN1
HOLE1
16
I
17
5
6
11
7
12
8
13
9
14
10
15
R2
R4
C11
R13
HOLE5
4
D15
HOLE49
13
14
1
U5
CPU socket
2
CN1
S-video port
11
CN17
Keyboard connector
3
CN4
CRT
12
CN19
Main battery connector
4
CN3
Docking
13
U15
IR
5
CN2
RJ45
14
CN20
HDD connector
6
CN2
RJ11
15
CON1
PCMCIA slot
7
CN5
Power jack
16
CN14
IEEE 1394 port
8
CN7
LCD connector
17
CN9-11
CN13
Four USB ports
9
CN15
Optical drive connector
Chapter 5
10
CN16
DIMM socket
79
T94
1
CN25
Line-in connector
2
CN27
Microphone-in connector
3
CN28
Line-out connector
4
CN26
Mini PCI connector
5
CN24
DIMM socket
D1
M 1
1
D2 0
L D
I
S D
2
2
1
E
J
M
4 8
3
2 4 8
F GH
K L
N
DA0ZI3MB6D7 REV:D
C948
R604
E
R566
C934 R572
C936 R574
I G I
C942
C944
C946
C947
G I
RP100
R545
R548
R550
C929
Q43
O
R560
Y8
JP15
C930
C933
C935
C938
R576
2
O Q45
R564
G
D33
45
88
89
16
14
8
9
9
T85 7
C858 C857
R515
Q42 O Q41
I
5 U30 4
G
T79
8
R P N ML K J
Y W V U T R P
D24 C900
ML
J
U40
R496
R513
D20
R525
U29
RP85 C985
RP86
RP84
C866 C864
H
G F
E
T92
G F
D
D
C904
C902
B
B A
T93
C873
C876
C880
C882
44
U37
176
D25
5
U41
4
C918
4
4
HOLE44
13
14
133
132
5
D
D
B
1 2 3 4 5 6 7 8 9 10
11
U27
C862
C869
C912
O
U43
K
H
F
M
A
Y7
13
R441
M
M
G
J
L
R458
C729
R454
C788
108
109
A
C863
C894
R547
R580
8
C955
R528
25
26
50
51
T91
12
48
C916
30
29
20
C943
L89
L90
C709
C700
C735
C734
C786
C713
R490
C839
C843
C855
Q40
U31
C875
C878
U34
100
24
37
36
25
C915
U36
U38
21
R578
R579
C949
C953
C956
C959
C958 C957
R438
11
1
7
5
3
2
U25
H
L
C662
C649
R419
1
2
4
10
11
12
5
7
3
9
8
6
C613
R405
C969
Q36
HOLE27
C562
R391
R398
C970
C603
C612
128
R384
R395
R394
R393
R392
C569
C
G
E
73
C835
I O
G
C845
C850
C800
R483
R484
D18
R486
C834
C836
C838
L83
C842
C844
C846
C849
RP95
T88
T87
T89
M
C927
R561
R565
R567
R573
C937
R575
C939
C952
D29 D
D30
D31
C951
U44
U21
R377
R380
C554
C557
C564
C565
C540
C549
C517
R359
C527 C523
C522
C525
C537
C519
C513
R357
U18
C464
R353
C482
R351
R348
C478 C476 C449
R356
C508
C511
C512
C494
R424
C667
C651
C653
C652
C665
C654
C659
C650
R412
R411
R410
C971
R401
R399
C543
R360
C534
C533
C532
C531
U20
R426
R425
R420
C675
R427
8
6
4
C676
R423
R422
R421
C664
C682
R414
C656
C666
C663
T70
C660
U23
C625
C661
R415
C657
M
9
10
11
12
C686
C683
C685
C677
C977
C692
K
C711
U28
D
R440
C694
C693
C697
T77
C691
C696
C690
C670
J
F
G
R439
C
PAD55
T76
T75
C699
C976
C674
C673
C688
L80
C792
PC124
R432
R431
R430
T74
C861
R518
R468
C789
R462
R471
C982
RP89
C852
C853
R524
R523
R522
R521
R520
C865
K
144
H
RP83
R517
C791
F
T80
E
T82
T81
1
2
3
4
5
6
6 5 4 3 2 1
J
T84
L
11
G
R534
12
B
13
E
D
C983
A
15
Y W V U T
C790
R465
R464
R463
C
17
C854
12
C978
T68
Q35
C941
I
C705
C704
C707
C706
R368
R370
R369
C545
T9 T7
L71
C535
C539
C551
C550
C940
L87
RP96
I
C687
C695
C658
C671
B
C913
RP98
K
C672
G
C950
RP97
R485
F
C799
H
R461
R460
R467
C793
R466
M
C668
C678
C606
C648
L79
L94
48
G
B
R493
HOLE32
1 2 3 4 5 6 7 8 9 10
G
G
L91
U35
R435
C689
C968
C906
U33
D
T71
C679
C669
C681
C607
R408
C620
L84
RP93
10
RP92
RP94
18
D22
2
T73
R498
C714
R443
C684
19
3
20
4
Y5
R529
C868
HOLE39
D21 C872
G
G
Y4
21
PC140
22
R489
R491
R492
R494
R497
C655
R500
R607
C899
R476
R475
R474
R473
R472
R404
R407
C638 R409
R413
23
PC132
R477
C728
R502
R514
C901
C903
C907
C908
C910
L85
R481
R480
R479
42 40
R478
B
L92
C914
C919 O
C928
C680
R508
R507
R506
R505
R504
R503
C895
C847
R512
R511
R510
T78
R509
Y3
R516
RP87
C859
C795
PU11
R433 PR122
U26
24
PR135
R526
2
R418
R417
103
102
AC
AB
AA
H
H
AF
AE
AD
PC120
C647
C646
U22
25
C874
64
T83
C723
PC122
PR121
PR120
R428
C698
C701
D17
T86
R530
R385
R378
R379
R383
R387
R389
R396
C598 R382
R386
R390
R397
26
R535
10
11
PR136
39
PC121
PC123
R429
C567
R608 R606
C994
CN24
C584
R482
PL20
R455
C732
65
A
16 14 12
13
17 15
H
H
38
39
U32
18
C840
C530
L72
24
22 20
25
23
21
C796
R554
C898
C897
R553
R552
R551
C896
T63
L76
R540
R539
R538
26
PC134
C544
C518
R350
C448
C451
C917
AF
AE
AD
AC
AB
AA
RP81
R358
C802
II
C804
C803
C724
C805
41
C806
199
C807
C566
L74
R367
R366
PC133
C808
R403
C556
R376
PD20
C611
C622
T62
PC143
PR128
PC144
PR127
PR126
T66
C624
C461
RP103
PC145
C431
U45
2
L78
C619
C559
R334
Q29
R589
C407
C406
U16
C405
R317
R316
R315
R314
R313
R312
F1
R311
R310
L64
PAD56
C618
C627
C626
C425
C424
C423
C422
RP51
R586
C436
R347
C430
R345
C446
C435
O
R354
C463
G
I Q27
R337
R336
Q30
C429
PC8
R342
L77
C596
R332
C421
C401
C400
C399
C389
C388
C387
C386
C385
C390
C391
C398
C397
C396
C395
C394
C393
C392
R308
R307
R300
R305
R304
R301
C402
T59
Q25
Q22
R333
C410
C416
R324
R373
R323
R322
R321
C411 R372
R320
C547
R319
C546
U17
R325
C412
C413
R326
C414
R331
R330
C415
R329
R328
R327
R318
D19
R519
I
T69
FF
U19
Q26
I
L93
G
C794
C538
G
RP102
G
O
PR131
C528
R590
R555
R559
R558
R557
24
RP91
R532
O
PC146
C823
C826
C536
C404
U39
C909
C911
R544
RP101
C879
C553
C555
C558
T61
RP104
G
RP105
C821
C822
L67
PC141
PR130
PR129
C479
C450
PR143
PC13
PL14
PR93
R339
CN23
Q31
Q33
RP52
C460
PR132
I
C514
PR103
PR104
C432
C433
PC80
PD14
PQ35
PC81
PC79
PC155
PL16
PC18
C462
PR134
PR133
PR124
PR125
C837
PC139
RP82
PC142
JJ
C524
L68
PC147
PR137
I
C529
R365
R364
R363
R362
R361
C495
C510
PC19
29
30
PR142
PD4
C477
PC148
L81
C
C
R299
A
C541
U42
BT1
T60
C552
D32
C892
G
C417
Q47
Q46
C881
O
C560
R371
R374
C542
C548
C926
C925
C932 C924
C931 C923
C922
C921
C920
Q44
C801
C561
L66
C824
C798
Q23 R303
C403
L86
R577
D28
Y6
R537
R541
C883 C884
C886
R542
C885 C888
C887 R543
C889
RP99
C890
C893
R549
C507
O
G
R531
C445
I
C877
L69
C526
L73
C825
C832
C579
C516
PR119
PR118
PC115
PC103
PC78
C418
Q52
25
JJ
C481
C496
PC136
PC135
T67
PC118
R306
Q51
C833
L82
G
I
R581
O
C726
C797
R453
C727
PQ47
200
PL18
O
L70
PQ49
C730
C563
C521
PC138
PC137
I
C600
G
PD21
C616
C760
C759
C758
C757
C756
C755
C754
C753
C752
C751
C750
C749
C748
C747
C746
C745
C744 RP57
C743 RP56
C742 RP55
C741 RP54
C740 RP53
C739
C738
T72
PC117
CN26
C708
C580
PL17
C725
PQ45
PC22
R582
G
C582
PC106
O
C954
Q37 R469
PR123
C710
PC130
PQ48
PC119
R309
C419
7 8
T95
C520
C581
PC104
PQ50
II
C586
C595
C601
C609
C615
C623
D23
C
C
C617
FF
PQ46
C591
PQ5
C891
R546
C568
C578
C585
C594
R400
R406
C614
C621
C731
5
PR22
Q38
PU13
I
PU9
6
R556
C905
PC131
PR146
C428
D26
C820
C819
C818
C817
C816
C815
C814
C813
C812
C811
C810
C809
PC154
4
D27
R569
R568
C831
C830
C829
C828
C827
Q34
3
R562
PC116
PC98
PR97
PC99
PR96
PR89
PC91
PC90
PR149
C571
PR88
PR87
PR84
C604
C608
PD5
PR108
PR83
PC149
C576
C577
C575
C574 C990
R381
C573
C572 T65
R388
C991
C570
T64
G
PC89
PC101
PC108
PR112
PC112
C599
C593
C592
C589
C590
C587
C480
PR145
C605
PD19
I
G
PQ42
PR105
PR110
O
C444
C443
C442
C441
C434
R344
R343
C440
C439
C438
C437
PR114
PQ38
C459
C458
C457
C456
C455
C454
C453
C452
PQ40
I
R470
C475
C474
C473
C472
C471
C470
C469
C468
C467
C466
C465
PU10
PR100
PR106
PC110
D16
19
R563
RP80
RP79
RP78
RP77
RP76
RP75
RP74
RP73
RP72
RP71
RP70
RP69
R457
RP68
RP67
RP66
RP65
R456
RP64
RP63
RP62
RP61
RP60
RP59
RP58
C493
C492
C491
C490
C489
C502 C488
C501 C487
C500 C486
C499 C485
C498 C484
C497 C483
R105
C506
C505
C504
C503
PQ41
PC100
PD17
PC109
PR113
PC113
PC82
C384
O
R570
R571
C785
C784
C783
C782
C781
C780
C779
C778
C777
C776
C775
C774
C773
C772
C771
C770
C769
C768
C767
C766
C765
C764
C763
C762
C761
C712
PQ37
PR102
PR109
PR111
PR117
C642
C645
C644
C641
C636
C635
C634
C633
C632
C631
C640
C630
C629
C628
C639
C637
PU8
HOLE19
R452
R451
R450
R449
R448
R447
R446
R445
R444
C722
C721
C720
C719
C718
C717
C716
C715
50
48
49
47
PQ43
PC87
PR81
4
1
3
PD18
G
I
PQ39
PC88
O
2
PL15
PR91
PC85
PC86
PC107
O
N
PD15
G
O
O
PD16
G
PC84
PC83
G
K
PR86
R302 Q24
I
H
PC95
2
Q28
6
E
PC94
PC92
PR95
PR101
PC102
PR116
PR90
PR92
PC96
PR98
PR107
PC111
PR115
C420
1
C
PR85
B
R416
HOLE12
C
PR94
CN22
C643
R335
R338
R340
R341
Q32
R346
C447
R349
R352
O
PF1
O
80
PD13
C17
C583
C588
C602
C610
I
PL12
PL13
R402
I
C597
O
I
PC97
Bottom View
C979
R355
L65
C509
C515
R375
L75
A
E
C
F2
U24
A
PAD54
12
L
J
C702
C703
C737
C787
72
R459
C733
C736
HOLE33
R487
R488
Q39
C841
R495
R499
R501
C848
C851
36
C860
R527
37
C867
C870
C871
C856
C987
R536
RP90
R533
RP88
1
T90
U46
75
76
CN25
CN27
E
CN28
2
3
C945
L88
3
4
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Ferrari 3000 series
products. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise
Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
NOTE: Exploded diagram is not ready as service CD released. We will update the service guide to CSD
website, please download the exploded diagram from the website if you need the files
Chapter 6
81
Exploded Diagram
1
3
4
5
2
7
6
8
9
10
11
12
13
14
82
Chapter 6
.
Picture
No.
Partname And Description
Part Number
Adapter
NS
ADAPTER LITE- ON PA-1900-05QA 3PIN W/
LED 90W
AP.A1003.001
ADAPTER LSE 0202C1990 3PIN W/LED 90W
AP.A1007.001
BATTERY SANYO LI-ION 8CELL (4UR18650F2-QC-ZG1, 4400mAH)
BT.FR103.001
BATTERY SIMPLO LI-ION 8CELL (LI-ION
BATTERY PACK ZG14S2P, 4400mAH)
BT.FR107.001
NS
MODEM CARD (Ambit T60M283.10)
54.T29V7.001
NS
MODEM /BLUETOOTH COMBO BOARD AMBIT
T60M665.00
54.T23V7.002
NS
WIRELESS LAN BOARD (802.11g) WNC KM8-1 54.A13V7.001
4
LAUNCH BOARD
55.T23V7.001
NS
TOUCH PAD BOARD W/CABLE
55.T23V7.002
Battery
13
Boards
Cables
Chapter 6
83
Picture
No.
Partname And Description
Part Number
NS
TOUCHPAD CABLE
50.T23V7.001
NS
MODEM CABLE
50.T23V7.002
NS
COVER SWITCH CABLE
50.T23V7.003
NS
POWER CORD US (3 pin)
27.A03V7.001
NS
POWER CORD EU ( 3 Pin)
27.T23V7.002
NS
POWER CORD PRC ( 3 Pin)
27.T23V7.003
NS
POWER CORD UK (3 PIN)
27.A03V7.004
NS
POWER CORD ITALIAN (3 PIN)
27.A03V7.005
NS
POWER CORD DANISH (3 PIN)
27.A03V7.006
NS
POWER CORD AU (3 PIN)
27.A03V7.008
3
MIDDLE COVER W/ NAME PLATE
42.FR1V7.001
NS
DIMM DOOR W/SCREW
42.FR1V7.002
10
LOWER CASE W/O SPEAKER
60.FR1V7.001
5
UPPER CASE W/TOUCHPAD HOLDER
60.FR1V7.002
8
I/O BRACKET W/MICROPHONE
33.FR1V7.001
Case/Cover/Bracket Assembly
84
Chapter 6
Picture
No.
Partname And Description
Part Number
NS
FRONT BEZEL FOR 4 IN 1 MODEL
42.T23V7.003
NS
FRONT BEZEL FOR NON-4 IN 1 MODEL
42.T23V7.103
NS
TOUCH PAD SHIELDING FOR TOUCH PAD
BOARD
33.T23V7.001
NS
TOUCH PAD BRACKET FOR TOUCH PAD
33.T23V7.002
NS
WIRELESS BOARD COVER
42.FR1V7.003
NS
BLUETOOTH ANTENNA
50.T23V7.004
NS
WIRELESS LAN ANTENNA Y CABLE
50.A13V7.001
NS
WIRELESS LAN ANTENNA
50.A13V7.002
NS
AMD Athlon XP Barton 2500+(1.8GHz) 40W
Low-Voltage OPGA
KC.A2502.40W
12
HDD 2.5" 30G HGST MORAGA
IC25N030ATMR04-0 08K0910 2.5"
KH.03007.002
HDD 2.5" 30G TOSHIBA NEPTUNE
MK3021GAS
KH.33004.001
Communication Module
CPU
HDD/ Hard Disk Drive
Chapter 6
85
Picture
No.
Partname And Description
Part Number
HDD 2.5" 30G FUJITSU V-40 MHT2030AT
4.2KRPM F/W:009A
KH.03006.002
HDD 2.5" 40G HGST MORAGA
IC25N040ATMR04-0 08K0633
KH.04007.004
HDD 2.5" 40G TOSHIBA NEPTUNE
MK4025GAS F/W:KA100A
KH.04004.002
HDD 2.5" 40G FUJITSU V40+ MHT2040AT
4.2KRPM F/W:0021
KH.04006.003
HDD 2.5" 60G HGST MORAGA
IC25N060ATMR04-0 08K0634
KH.06007.002
HDD 2.5" 60G TOSHIBA NEPTUNE
MK6021GAS
KH.36004.001
HDD 2.5" 60G FUJITSU V40+ MHT2060AT
4.2KRPM F/W:0021
KH.06006.003
NS
HDD COVER
42.FR1V7.005
NS
HDD CASE
33.FR1V7.002
2
KEYBOARD DARFON US INTERNATIONAL (
99.N3482.41D, 84 keys)
KB.T2307.001
KEYBOARD DARFON SPANISH (
99.N3482.40S, 85 keys)
KB.T2307.003
KEYBOARD DARFON BRAZILIAN
PROTUGESE ( 99.N3482.406, 85 Keys)
KB.T2307.005
Keyboard
86
KEYBOARD DARFON UK NSK-A640U 85KEYS
KB.T2507.002
KEYBOARD DARFON GERMAN NSK-A640G
85KEYS
KB.T2507.003
KEYBOARD DARFON ITALIAN NSK-A640E
85KEYS
KB.T2507.004
KEYBOARD DARFON FRENCH NSK-A640F
85KEYS
KB.T2507.006
KEYBOARD DARFON SWISS/G NSK-A6400
85KEYS
KB.T2507.007
KEYBOARD DARFON PORTUGUESE NSK-06
85KEYS
KB.T2507.009
KEYBOARD DARFON ARABIC NSK-A640A
84KEYS
KB.T2507.010
KEYBOARD DARFON BELGIUM NSK-A641A
85KEYS
KB.T2507.012
KEYBOARD DARFON SWEDEN NSK-A640W
85KEYS
KB.T2507.013
KEYBOARD DARFON CZECH NSK-A640C
85KEYS
KB.T2507.014
KEYBOARD DARFON HUNGAIAN NSK-A640Q
85KEYS
KB.T2507.015
Chapter 6
Picture
No.
Partname And Description
Part Number
KEYBOARD DARFON NORWAY NSK-A640N
85KEYS
KB.T2507.016
KEYBOARD DARFON DANISH NSK-A640D
85KEYS
KB.T2507.017
LCD MODULE 15" TFT SXGA+ HSD 150PK17
W/ANTENNA
6M.FR1V7.002
LCD MODULE 15" TFT SXGA+ CMO IDT
N150P3 W/ANTENNA
6M.FR1V7.003
LCD 15" TFT SXGA+ HSD 150PK17
LK.15007.007
LCD 15" TFT SXGA+ CMO IDT N150P2-L04
LK.1500D.003
NS
INVERTER BOARD W/MAYLAR E SUMIDA
53261-0590
19.T23V7.011
NS
LCD BRACKET 15" RIGHT W/HINGE
33.T23V7.007
NS
LCD BRACKET 15” LEFT W/HINGE
33.T23V7.008
NS
LCD PANEL WITH LOGO-15”
60.FR1V7.003
NS
LCD BEZEL 15"
42.FR1V7.006
NS
LCD COAXIAL CABLE FOR 15" XGA spwg-B
50.T23V7.021
LCD
1
NS
Chapter 6
87
Picture
No.
Partname And Description
Part Number
Main Board
9
MAINBOARD 128MB VGA W/SMART CARD
READER,PCMCI SLOT,W/O CPU MEMORY
MB.FR106.001
NS
PCMCIA SLOT
22.A13V7.001
NS
256MB DDR333 HYS64D32020GDL-6-B
INFINEON
KN.25602.009
256MB DDR333 NT256D64SH8BAGM-6K
NANYA
KN.25603.009
256MB DDR333 MT8VDDT3264HDG-335C3
MICRON
KN.25604.009
256MB DDR333 M470L3224DT0-CB300
SAMSUNG
KN.2560B.005
256MB DDR333 W30256AAEPI652A ELPIDA
KN.25609.002
512MB DDR333 HYS64D64020GBDL-6-B
INFINEON
KN.51202.007
512MB DDR333 NT512D64S8HBAFM-6K
NANYA
KN.51203.005
512MB DDR333 EBD52UC8AARA-6B ELPIDA
KN.51209.002
11
DVD DUAL MODULE 4X PIONEER DVRK12RA
6M.FR1V7.001
NS
DVD DUAL 4X PIONEER DVR-K12RA
KU.00405.005
NS
DVD DUAL BEZEL FOR PIONEER
42.FR1V7.004
NS
OPTICAL DEVICE BRACKET
33.A13V7.002
NS
TOUCHPAD
56.FR1V7.001
Memory
Optical Drive
Pointing Device
88
Chapter 6
Picture
No.
Partname And Description
Part Number
Speaker
14
SPEAKER SET
6K.T23V7.002
7
HEATSINK W/FAN
6K.T23V7.003
NS
VGA HEATSINK
34.A13V7.001
NS
VGA MEMORY HEATSINK
34.A13V7.002
NS
4 IN 1 READER
6K.T29V7.001
NS
MICROPHONE
23.T23V7.001
NS
LCD LATCH W/O SPRING
6K.FR1V7.001
Heatsink
Reader
Microphone
Others
NS
LCD SCREW RUBBER UPPER
47.FR1V7.001
NS
LCD SCREW RUBBER LOWER
47.FR1V7.002
NS
NUT-I/O
86.T23V7.001
NS
SCREW M1.6X4.0-I-NI-NYLOK
86.T23V7.002
NS
SCREW M2.0X2.5-I-NI-NYLOK
86.A03V7.007
Screws
Chapter 6
NS
SCREW M2.0X3.0-I-NI-NYLOK
86.A03V7.012
NS
SCREW M2.0X3.5-I-NI-NYLOK
86.T23V7.005
NS
SCREW M2.0X5-I-NI-NYLOK
86.T23V7.006
NS
SCREW M2.5X3-I-NI-NYLOK
86.A03V7.010
NS
SCREW M2.5X4.0-B-NI-NYLOK
86.T23V7.008
NS
SCREW M2.5X4-I-NYLOK
86.T23V7.009
NS
SCREW M2.5X5.0-I-NI-NYLOK
86.T23V7.010
NS
SCREW M2.5X5.5-P-NI-NYLOK
86.T23V7.011
NS
SCREW M2.5X0.45+7I-NYLOK
86.T23V7.012
NS
SCREW M1.7X3.5-I-BZN
86.A03V7.009
NS
SCREW M2X3-I-BNI-NYLOK
86.T23V7.014
NS
SCREW M2.0X5.0-I-BNI-NYLOK
86.T23V7.015
NS
SCREW M2.0X6.0-I-NI-NYLOK
86.T23V7.017
NS
SCREW M2.5X2-I-NI-NYLOK
86.T23V7.018
NS
SCREW M2.5X4-I-BNI
86.T23V7.019
89
Appendix A
Model Definition and Configuration
Ferrari 3000 Series
Model
Number
3000LMi
Appendix A
CPU
Athlon XP
2500+ 40W
LCD
15.0"
SXGA+
Memory
DDR333
2x256MB
HDD
(GB)
60
ODD
2.4x
Card
Reader
4 in 1
Wireless
LAN
11g
DVD-Dual
90
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Ferrari 3000 series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B
91
Microsoft® Windows® XP Home Environment Test
Item
Display
Specifications
LCD:
Acer AL722
Compaq TFT 5004
Phillips Brilliance 150P
CRT:
Dell Trinitron 21”
ViewSonic GS773
ViewSonic GS790
ViewSonic PF775
Phillips Brilliance 109P 19”
Parallel Port
Printer:
HP Laser Jet 5M
HP Desk Jet 840C
HP Laser Jet 2100
Canon BJC-3000
IOMega ZIP 100 (LPT Port)
IOMega ZIP 250 (LPT Port)
Cable:
ECP Cable (LL5)
1394 Port
1394 HDD/IEEE 1394 (Fire Wire)/USB 1.1 Combo Hard Drive
1394 External HDD CASE
1394 CCD (APLUX C102T)
1394 MO: FUJITSU LIMITED MDF3130EE
1394 Cable P to P(Pci)
Projector
Panasonic PT_L757U
Panasonic PT_L556EA
USB 2.0
USB HUB: Highspeed\4 Port
USB HDD: Billionton
USB CD-RW: YAMAHA CD/RW-70
USB C.F. Card Reader: IOGEAR\ GFR201
USB 6 in 1 Card Reader: SanDisk ImageMate 6 in 1
USB DVD/CD-RW: Pioneer DVR-104
USB DVD/CD-RW: Ricoh MP5125A
USB Memory: USB Drive 128MB
GB LAN HUB
3 COM SUPER STACK II \ 3C16611 24port
S-Video
TV: Sony Trinitron 14” \ PVM-14M4U
Sony Trinitron 14” \ PVM-14M2U
92
Appendix B
Item
PC Cards
Specifications
Modem Card:
3Com 56K Modem (3CXM756)
Xircom 56K Modem (CM-56)
Xircom 56K Modem (CM-56G)
Billionton 56K Modem (FM56C-BF)
Psion-Gold Card Clabal 56K+Fax
LAN Card:
3Com Lan Card (3CCFE574BT)
D-Link Fast Ethernet DFE-650
D-Link CardBus DFE-660
3COM 10M CardBus LAN Card (3CCFE589ET)
Xircom CreditCard Ethernet 10/100 (CE3B-100)
Pci_Fast Ethernet Card FNW-3602-TX
LAN Card Bus Card:
3COM 10/100 CardBus LAN Card (3CCFE575CT)
Xircom CardBus Ethernet II 10/100 (CBE2-100)
SCSI:
Adaptec SlimSCSI APA-1460D Card
LAN + Modem Card:
Xircom CreditCard Ethernet + Modem 56K (CEM56-100)
ATA Card:
Adapter Flash Card+ SanDisk CF Card 128MB
PQI Compact Flash Card+ PQI CF Card 128MB
Zip Card:
ZIOMEGA USB ZIP 250
1394 CardBus Card:
IEEE 1394 CardBus Card\ DV Megician \UPMOST
Wireless LAN Card:
CISCO AIRONET 350 SERIES\AIR-PCM350
Quanta Wireless LAN Card \ WL-211F
Wireless Card Bus Card: BUFFALD WLI-CB-G54A
Card Reader:
Apapter PCMCIA 4 in 1
PQI CF CARD Reader
PNY PCMCIA 4 in 1
MMC Card:
SanDisk 32MB
SanDisk 64MB
PQI 64MB
MS Card:
Apacer 128MB
SONY Memory Stick 128MB
SD Card:
Transcend 128MB
SanDisk 128MB
CF Card:
PQI 128MB
SanDisk 8MB
SanDisk 128MB
Appendix B
93
Item
USB Port
Specifications
K/B+Mouse
Logitech K/B+Mouse+Receiver
Microsoft Wireless Optical DeskTop for Bluetooth K/B+Mouse
USB Mouse:
Microsoft IntelliMouse Optical USB & PS2 Compatible
Microsoft Notebook Optical Mouse
Microsoft Optical Mouse Blue USB & PS/2 Compatible\MIC:E-C011-02-1620
Logitech Wheel Mouse M-BB48
Logitech MouseMan Dual Optical \ M/N:M-BL63B
Logitech iFEEL Mouse M-UN58a
Acer USB Mouse MP0930
Acer USB Mouse M012B0
USB Keyboard:
NMB K/B
ZIPPY USB Keypad TK532
USB Camera:
Intel YC72
Logitech QuickCam Home
Dlink WebCam DSB-C300
USB HDD:
HD 530 Tested to comply with FCC Standards
USB CD-ROM:
YAMAHA CD/RW-70
USB Printer:
HP DiskJet 3425 Colour inKlet printer
HP DeskJet 840C
HP deskject 450
Canon BJC-3000
USB FDD:
Acer USB FDD YD-8U10
Teac USB FDD
Logitec USB FDD
USB Memory:
USB DRIVE 128MB
Panasonic SUPER DISK \ LKRF235U
USB LAN:
Billionton USB-10/100 FastEthernet
BUFFALO USB-10/100M Ethernet LUX-TX
USB Zip:
IOMEGA USB ZIP 100
IOMEGA USB ZIP 250
USB Scanner:
HP ScanJet 5300c
USB Speaker:
Philips USB Speaker (DIGITAL Speaker System)
USB HUB:
PCI_USB HUB\UH-400
USB Gamepad:
Logitech WingMan GAMEPAD EXTREME
Logitech WingMan EXTREME DIGITAL 3D
Logitech WingMan RUMBLEPAD
USB Card Reader:
Iwill 6 in 1 Card Reader
Pro Compact Flash Card Reader
94
Appendix B
Item
Audio Jacks
Specifications
Speaker
DENON Amplifier (AMP) AVR-1802
LOUDSPEAKER
Gateway Speaker
Earphone:
AIWA HP-X121 Earphone
PHILIPS Earphone
NEC Earphone
e STEREO DYNAMIC HEADPHONES E-750
Pro. 2 DYNAMIC HEADPHONES PH-B333G
Panasonic Stereo Headphones \ RP-H1245
DELL harman/kardon
Microphone
AIWA Mini Microphone
Condenser MIC. EM-420T
Audio Jack
JS-100 Jazz 3D Speaker
SONY Earphone MDR-CD60
Microsoft microphone
Microphone
Condenser Microphone
Dynamic Microphone
Appendix B
95
96
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides for all models
T
User's manuals
T
Training materials
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveler's Warranty (ITW)
T
Returned material authorization procedures
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
97
98
Appendix C
Index
A
Battery Pack 48
CD-ROM/DVD-ROM Module 53
Floppy Disk Drive 57
Procedure Flowchart 47
ACPI 1.0a 22
AFLASH Utility 44
Display 3
Audio 25
E
B
Error Symptom-to-Spare Part Index 65
Battery Pack 50
External CD-ROM Drive Check 62
BIOS 22
package 22
password control 22
ROM size 22
ROM type 22
vendor 22
Version 22
External Diskette Drive Check 62
F
Features 1
Flash Utility 44
Floppy Disk
BIOS Setup Utility 31
removing the 57
BIOS Supports protocol 22
FRU (Field Replaceable Unit) List 81
BIOS Utility 31
Basic System Settings 36
Navigating 32
Onboard Device Configuration 39
Startup Configuration 38
System Information 32
System Security 43
H
Hot Keys 13
I
Indicators 12
Board Layout 4
Bottom View 5
Top View 4
C
Intermittent Problems 76
J
Jumper and Connector Locations 79
Cache
controller 22
size 22
Top View 79
K
caps lock
Keyboard 28
on indicator 12
CardBus 27
CPU
core voltage 22
package 22
type 22
Keyboard or Auxiliary Input Device Check 62
L
L2 cache 22
M
D
Memory Check 63
Model Definition 90
DIMM 22
Combinations 23
external 51
package 22
removing 51
Speed 22
voltage 22
Disassembly
Index
Modem 23
N
num lock
on indicator 12
O
99
Online Support Information 97
P
Panel 6
Bottom 11
left 6
Rear 9
right 9
Parallel Port 26
PC Card 12, 27
PCMCIA 27
Pentium III 22
Power System Check 63
Battery Pack 64
Processor 22
R
RMA 81
S
Second Level Cache 22
System
Block Diagram 3
Layout 4
System Diagnostic Diskette 44
System Memory 22
System Utilities 31
System Utility Diskette 44
T
Test Compatible Components 91
Touchpad Check 64
Troubleshooting 61
U
Undetermined Problems 77
USB 27
utility
BIOS 31
V
Video 26
W
Windows XP Pro Environment Test 92
100
Index
Index
101
Download PDF

advertising