advertisement
Acer TravelMate 2400/3210/3220/3230 Series
Service Guide
Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
II
Revision History
Please refer to the table below for the updates made on TravelMate 2400/3210/3220/3230 service guide.
Date
2005/08/22
2005/09/30
2005/12/07
Chapter
Chapter 1, 4, 5, 6
Chapter 1, 2, 6
Chapter 1
Updates
Add docking spec. to Chapter 1, 5, 6.
Add Insyde BIOS POST codes and POST messages to
Chapter 4.
Add TravelMate 3230 specification.
Add environment conditions on page 3.
Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES
NOTE
WARNING
CAUTION
IMPORTANT
Denotes actual messages that appear on screen.
Gives bits and pieces of additional information related to the current topic.
Alerts you to any damage that might result from doing or not doing specific actions.
Gives precautionary measures to avoid possible hardware or software problems.
Reminds you to do specific actions relevant to the accomplishment of procedures.
IV
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide. In such cases, please contact your regional offices or the responsible personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information available on your regional web or channel. If, for whatever reason, a part number change is made, it will not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
V
VI
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Platform and memroy
TravelMate 3210/TravelMate 3220/TravelMate 3230
Intel
®
Centrino
TM
Mobile Technology, featuring: t
Intel
®
Pentium
®
M Processor 730/740/750/760/770 (2 MB L2 cache, 1.60/1.73/1.86/2/2.13 GHz, 533
MHz FSB) t
Intel
®
Pentium
®
M Processor 725 (2MB L2 cache, 1.6 GHz, 400 MHz FSB) t
Intel
®
915GM/PM Express chipset t
Wireless solution: integrated Intel
®
PRO/Wireless 2200BG network connection (dual-band 802.11b/g)
Wi-Fi
®
CERTIFIED
TM
solution, supporting Acer SignalUp wireless technology
TravelMate 2400 t
Intel
®
Pentium
®
M Processor 725 (2MB L2 cache, 1.6 GHz, 400 MHz FSB) t
Intel
®
Celeron
®
M Processor 350/360/370 (1 MB L2 cache, 1.30/1.40/1.50 GHz, 400 MHz FSB) t
Intel
®
910GML Express chipset t
Wireless solution: integrated Intel
®
PRO/Wireless 2200BG network connection (dual-band 802.11b/g)
Wi-Fi
®
CERTIFIED
TM
solution, supporting Acer SignalUp wireless technology
T
T
Intel
®
915GM/PM (for TravelMate 3210/3220/3230)/Intel
ICH6-M (Mobile Intel 82801FB)
®
910GML (for TravelMate 2400)+Intel
256/512 MB of DDR2 400/533 MHz memory, upgradeable to 2 GB using two soDIMM modules
(dual-channel support)
Display
T
T
T
T
T
14.1 WXGA color TFT LCD, 1280 x 800 resolution; 16:10 viewing ratio, supporting simultaneous multi-window viewing on dual displays via Acer GridVista 16.7 million colors
Intel
®
915GM/PM (TravelMate 3210/3220/3230)/Intel
®
910GML (TravelMate 2400) integrated 3D graphics, featuring Intel Graphics Media Accelerator 900 and up to 128 MB of VRAM, supporting
Microsoft
®
DirectX
®
9.0 and dual independent display
ATI MOBILITY
TM
RADEON
TM
X700 with 64 MB or higher of dedicated VRAM, supporting ATI
POWERPLAY
TM
3220/3230 only)
5.0, PCI Express
TM
, Microsoft
®
DirectX
®
9.0 and DualView (TravelMate 3210/
MPEG-2/DVD hardware-assisted capability
S-video/TV-out (NTSC/PAL) support (TravelMate 3210/3220/3230 only)
Storage subsystem
T
40/60/80 GB ATA/100 hard disk drive
T
Optical drive options: t
DVD-Super Multi double layer (TravelMate 3210/3220/3230)
Chapter 1 1
I/O Ports
T
T
T
T
T
T
T
T
T
T
T
T
Input devices
T
Acer FineTouch
TM
keyboard
T
T
T
84/85-key keyboard
Touchpad with 4-way integrated scroll button
Four easy-launch buttons
T
Two front-access LED-buttons: WLAN and Bluetooth
®
Audio
t
DVD-Dual double layer (TravelMate 2400) t
DVD/CD-RW combo
5-in-1 card reader (MS/MS PRO/MMC/SD/xD-Picture Card
T
T
Audio system with two built-in speakers
MS-Sound compatible
Communication
T
Modem: 56K ITU V.90/V.92 modem with PTT approval; wake-on ring ready
T
LAN: 10/100/ (TravelMate 2400) or gigabit Ethernet (TravelMate 3210/3220/3230); wake-on ring ready
T
T
T
WLAN: integrated 802.11b/g Wi-Fi
®
CERTIFIED
TM
solution (TravelMate 2400), or Intel
®
PRO/
Wireless 2200BG network connection (dual-band 802.11b/g) Wi-Fi
(TravelMate 3210/3220/3230)
®
CERTIFIED
TM
solution
Acer SignalUp wireless technology support
WPAN: integrated Bluetooth
®
Human-centric design and ergonomics
T
Rugged, yet extremely portable design
T
T
T
T
T
Stylish appearance
Full-size keyboard with four programmable launch keys
Ergonomically-centered touchpad pointing device
Acer FineTouch keyboard with a 5-degree curve
Internet 4-way scroll button
Three USB 2.0 ports
5-in-1 card reader (MS/MS-PRO/MMC/SD/XD)
PC Card slot (one Type II)
IEEE 1394 port (TravelMate 3210/3220/3230)
Fast infrared (FIR) port (TravelMate 3210/3220/3230)
External display (VGA) port
S-video/TV-out (NTSC/PAL) port (TravelMate 3210/3220/3230)
Headphones/speaker/line-out port
Microphone/line-in jack
Ethernet (RJ-45) port
Modem (RJ-11) port
2 Chapter 1
T
T
DC-in jack for AC adaptor
Acer ezDock (TravelMate 3220 only)
Dimensions and weight
T
335 (W) x 240 (D) x31.9/34.1 (H) mm (13.2 x 9.45 x 1.26/1.34 inches)
T
T
T
TravelMate 3220: 2.6 Kg (5.73lbs)
TravelMate 2400/3210: 2.25 kg (4.96 lbs)
TravelMate 3230: 2.0 kg (4.4lbs)
Environment
T
Temperature:
T t t t
Non-opterating: -20 degree C to 65 degree C
Opterating: 5 degree C to 35 degree C
Humidity: t
Opterating: 20%~80%
Non-operating: 20%~80%
Chapter 1 3
System Block Diagram
Intel Pentium-M/
Celeron-M CPU
Micro FC-PGA
Thermal Sensor
Clock Generator
CRT & TV-Out Conn.
Daughter Card (M26P)
PCI-Express x16
LVDS Conn.
Mobile Intel 915PM/ GM and 910GML Express
Chipset (Alviso)
DDR II SODIMM 2
DDR II SODIMM 1
Min i-PCI
So cket
BroadCOM
LAN
BCM440 1KFB
/ BCM578 8M
PCMCIA &
CardRead er
Controller
ENE CB7 12
13 94
Con troller
TSB34AB21A
Mobile Intel 82801FB
ICH6-M
RJ45
PCMCIA
Slo t
13 94 Con n.
4 -Pin s
4-in -1
CradReader
Slo t
Super I/O
SMsC LPC47N217
Power ON/ OFF
Circuit
ENE KB910Q
(EC + KBC)
DC/ DC Interface
Circuit
Power DC/DC
Circuit
RTC Circuit
Power-OK Circuit
USB Conn. x3
USB Conn. x1 for BlueTooth
Audio Codec
Amplifier
MDC Conn.
SATA Conn.
PATA Conn.
Speaker
Conn.
Jack x2
RJ-11
Internal K/B
BIOS
Touch-Pad Conn.
4 Chapter 1
Board Layout
Top View
SW3
JP1
SW2
SW4 SW5 SW6
SW1
2
2
JP7
2
2
JP4
2
JP5
2
JP42
KQ:
2
2
SW3
JP1
SW2
SW4
SW5
SW6
Power Switch
Bluetooth Connector
E-mail Switch
Internet Browser Switch
Emanager Switch
User Programmable Switch
SW1
JP5
JP4
JP42
JP7
JP10
Lid Swtich
Touchpad Connector
Keyboard Connector
Speaker Connector
PCMCIA Slot
Microphone Connector
Chapter 1 5
Bottom View
2
JP21
2
PJP11
JP20
JP39
JP26
JP31
2
JP16
2
JP22
PCN1
2 JP13 JP12
JP14
2
JP19
2
JP3
2
JP17
2
2
2
JP35
2
T2
JP28
Q2 JP29
JP36
2
JP23
JP24
2
JP25
2
JP30
2
U42
2
JP41
JP40
IR1
2
6
JP13
JP12
JP14
JP3
JP17
JP19
JP23
JP21
PJP11
JP20
JP16
JP22
PCN1
Fan Connector
Battery Connector
CPU Socket
LVDS Connector
VGA Board Connector
AC-IN
USB Port
Acer ezDock (for TravelMate 3220 only)
Modem Board Connector
External Display Port
S-Video Port
RJ11/RJ45
Modem Cable Connector
JP41
JP28
JP35
U42
JP26
JP31
JP39
JP24
JP25
JP30
JP36
IR
JP40
USB Port
USB Port
IEEE 1394 Port
Card Reader Connector
Infrared Receiver
Headphone out/line-out Jack
(support SPDIF)
Mic-in Jack
HDD Connector
Wireless LAN Card Connector
BIOS
DDR2 Socket
DDR2 Socket
ODD Connector
Chapter 1
A TravelMate tour
After knowing your computer features, let us show you around your new TravelMate computer.
Front View
Chapter 1
6
7
4
5
8
9
2
3
#
1
Icon Item
Display screen
Power button
Launch keys
Microphone
Status indicators
Palmrest
Click buttons (left, center and right)
Touchpad
Keyboard
Description
Also called LCD (liquid-crystal display), displays computer output.
Turns the computer on and off.
Buttons for launching frequently used programs. See “Launch keys” section for more details.
Internal microphone for sound recording.
Light-Emitting Diodes (LEDs) that turn on and off to show the status of the computer’s functions and components.
Comfortable support area for our hands when you use the computer.
The left and right buttons function like the left and right mouse buttons; the center button serves as a 4-way scroll button.
Touch-sensitive pointing device which functions like a computer mouse.
For entering data into your computer.
7
Closed Front View
5
6
7
2
3
#
1
4
Icon
Speaker-out/line-out/
Headphone jack
Mic-in jack
Speakers
Item
Bluetooth
® communication button/ indicator
Description
Connects to audio line-out devices (e.g., speakers, headphones).
Accepts inputs from external microphone.
Left and right speakers deliver stereo audio output.
Press to enable/disable Bluetooth function.
Lights to indicate the status of
Bluetoothcommunications (option only available for TravelMate 3210/3220/3230).
Wireless communication button/ indicator
Press to enable/disable Wireless function.
Lights to indicate the status of wireless
LAN communications.
Power indicator
Lights when the computer is on.
Battery indicator
Lights when the battery is being charged
Left View
8
#
1
Icon Item
External display port
Description
Connects a display device (e.g., external monitor, LCD projector).
Chapter 1
Chapter 1
2
3
4
5
6
7
8
9
10
S-video/TV-out port
Network jack
Connects to a television or display device with S-video input (TravelMate 3210/3220/
3230 only).
Connects to an Ethernet 10/100/1000based network.
Modem jack Connects to a phone line.
Two USB 2.0 ports
IEEE 1394 port
PC Card slot
Connects to USB 2.0 devices (e.g., USB mouse, USB camera).
Connects to IEEE 1394 devices
(TravelMate 3210/3220/3230 only).
Connects to one Type II PC Card.
5-in-1 card reader
Infrared port
PC Card slot eject button
Accepts and MS, MS PRO, MMC, SD, or xD-Picture card (manufacturing option).
Note: Only one card can operate at any given time.
Interfaces with infrared devices like infrared printer and IR-aware computer (TravelMate
3210/3220/3230 only).
Ejects the PC Card from the slot.
9
Right View
4
5
6
2
3
#
1
Icon Item
Optical drive
LED indicator
Optical drive eject button
Description
Internal optical drive; accepts CDs or DVDs depending on the optical drive type.
Lights up when the optical drive is active.
Ejects the opotical drive tray from the drive.
Emergency eject hole Ejects the optical drive tray when the computer is turned off.
Ventilation slots Enable the computer to stay cool, even after prolonged use.
Security Keylock Connects to a Kensington-compatible computer security lock.
10 Chapter 1
Rear Panel
TravelMate 3210/3230 Rear View
#
1
2
3
Icon Item
Battery bay
Power jack
Description
Houses the computer’s battery pack.
Connects to an AC adaptor.
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
TravelMate 3220 Rear View
Chapter 1
#
1
2
3
4
Icon Item
Battery bay
Power jack
Acer ezDock port
Description
Houses the computer’s battery pack.
Connects to an AC adaptor.
Connect to USB 2.0 devices (e.g., USB mouse, USB camera).
Connects to the Acer ezDock (TravelMate
3220 only)
11
Bottom Panel
6
7
4
5
2
3
#
1
Item
Battery bay
Battery lock
Cooling fan
Description
Houses the computer’s battery pack.
Locks the battery in place.
Helps keep the computer cool.
Note: Do not cover or obstruct the opening of the fan.
Memory compartment Houses the computer’s main memory.
Hard disk bay Houses the computer’s hard disk (secured by two screws).
Battery release latch
Wireless LAN card compartment
Releases the battery for removal.
Houses the computer’s mini PCI.
7
12 Chapter 1
Indicators
The computer has three easy-to-read status indicators on the upper-left above the keyboard, and four on the front panel.
The power, battery and wireless communication status indicators are visible even when the LCD display is closed.
Icon Function
Cap lock
Description
Lights when Cap Lock is activated
Num lock Lights when Num Lock is activated.
Media Activity
Bluetooth
Wireless LAN
Power
Battery
Indicates when the hard disc or optical drive is active.
Indicates the status of Bluetooth communication.
Indicates the status of wireless LAN communication.
Lights up when the computer is on.
Lights up when the battery is being charged.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows green when in AC mode.
Chapter 1 13
Launch Keys
Located at the upper-right, above the keyboard are four buttons. These buttons are called launch keys. The are: mail, Web browser, Acer Empowering key “ “ and one user-programmable button.
Press “ “ to ru the Acer eManager. Please see “Acer eManager”. The mail and Web buttons are pre-set to email and Internet programs, but can be reset by users. To set the Web browser, mail and programmable keys, run the Acer Launch Manager.
Launch key
Web browser
P
Default application
Email application (user-programmable)
Internet browser (user-programmable)
Acer eManager (user-programmable)
User-programmable
14 Chapter 1
Touchpad
The built-in touchpad is a pointing device that senses movement on its surface. This means the cursor responds as you move your finger across the surface of the touchpad. The central location on the palmrest provides optimum comfort and support.
Touchpad Basics
The following teaches you how to use the touchpad:
T
T
T
Move your finger across the touchpad (2) to move the cursor.
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button.
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button mimics your cursor pressing on the right scroll bar of Windows applications.
Function
Execute
Select
Left Button (1)
Click twice quickly
Click once
Right Button
(4)
Main touchpad
(2)
Tap twice (at the same speed as doubleclicking the mouse button)
Tap once
Center button (3)
Chapter 1 15
Function
Drag
Left Button (1)
Click and hold, then use finger to drag the cursor on the touchpad
Right Button
(4)
Main touchpad
(2)
Tap twice (at the same speed as doubleclicking a mouse button) then hold finger to the touchpad on the second tap to drag the cursor.
Center button (3)
Access context menu
Scroll
Click once
Click and hold to move up/down/left/right.
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response.
Tapping too hard will not increase the touchpad’s responsiveness.
16 Chapter 1
Using the Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys.
Lock Keys and embedded mumeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Caps Lock
Num lock
<Fn>+<F11>
Scroll lock
<Fn>+<F12>
Description
When Caps Lock is on, all alphabetic characters typed are in uppercase.
When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator
(complete with the arithmetic operators +, -, *, and /).
Use this mode when you need to do a lot of numeric data entry. A better solution would be to connect an external keypad.
When Scroll Lock is on, the screen moves one line up or down when you press the up or down arrow keys respectively. Scroll Lock does not work with some applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys.
Desired Access
Number keys on embedded keypad
Cursor-control keys on embedded keypad
Main keyboard keys
Num Lock On
Type numbers in a normal manner.
Hold <Shift> while using cursor-control keys.
Hold <Fn> while typing letters on embedded keypad.
Num Lock Off
Hold <Fn> while using cursor-control keys.
Type the letters in a normal manner.
Chapter 1 17
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Windows key
Icon
Application key
Description
Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the
Start menu. It can also be used with other keys to provide a variety of function:
+ <Tab> Activates next taskbar button.
+ <E> Opens the My Computer window
+ <F1> Opens Help and Support.
+ <F> Opens the Find: All Files dialog box.
+ <R> Opens the Run dialog box.
+ <M> Minimizes all windows.
<Shift>+ action.
+ <M> Undoes the minimize all windows
This key has the same effect as clicking the right mouse button; it opens the application’s context menu.
18 Chapter 1
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like sreen brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Fn-F4
Fn-F5
Fn-F6
Fn-F7
Hot Key
Fn-F1
Fn-F2
Fn-F3
Fn-F8
Fn-w
Icon Function
Hot key help
Description
Displays help on hot keys.
Acer eSetting Launches the Acer eSettings in Acer eManager.
Acer ePowerManagement
Launches the Acer ePowerManagement in Acer eManager.
Sleep Puts the computer in Sleep mode.
Display toggle
Screen blank
Touchpad toggle
Switches display output between the display screen, external monitor (if connected) and both.
Turns the display screen backlight off to save power.
Press any key to return.
Turns the internal touchpad on and off.
Speaker toggle
Volume up
Turns the speakers on and off.
Increases the speaker volume.
Chapter 1 19
Hot Key
Fn-y
Fn-x
Fn-z
Icon Function
Volume down
Description
Decreases the speaker volume.
Brightness up Increases the screen brightness.
Brightness down Decreases the screen brightness
20 Chapter 1
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.
To type:
The Euro symbol
1.
Open a text editor or word processor.
2.
Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then press the<5> symbol at the upper-center of the keyboard.
The US dollar sign
1.
Open a text editor or word processor.
2.
Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the
<4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information.
Chapter 1 21
Hardware Specifications and Configurations
Processor
Item
CPU type
Core logic
CPU package
CPU core voltage
Specification
TravelMate 3210/TravelMate 3220/TravelMate 3230
Intel
®
Pentium
®
M Processor 730/740/750/760/770 (2 MB L2 cache, 1.60/
1.73/1.86/2/2.13 GHz, 533 MHz FSB)
Intel
®
Pentium
®
M Processor 725 (2MB L2 cache, 1.6 GHz, 400 MHz FSB)
TravelMate 2400
Intel
®
Pentium
®
M Processor 725 (2MB L2 cache, 1.6 GHz, 400 MHz FSB)
Intel ® Celeron ® M Processor 350/360/370 (1 MB L2 cache, 1.30/1.40/1.50
GHz, 400 MHz FSB)
Intel ® 915GM/PM (for TravelMate 3210)/Intel ® 910GML (for TravelMate
2400)+Intel ICH6-M (Mobile Intel 82801FB)
Intel socketable 478pin Micro-BGA
1.308V (highest frequency mode) to 0.956V (low frequency mode)
0.748V (deeper sleep mode)
BIOS
Item
BIOS vendor
BIOS Version
BIOS ROM type
BIOS ROM size
BIOS package
Supported protocols
Specification
Phoenix
3A03
SST 39SF040A, 512KX8 CMOS Boot Block Flash Memory
512KB
32-pin PLCC
ACPI 1.0b, PC Card 95, SM BIOS 2.3, IEEE1284-ECP/EPP, PCI 2.2, PnP
1.0a, DMI 2.0, PS/2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM bootable, IEEE 1394
Set by setup manual BIOS password control
Second Level Cache
Item
Cache controller
Cache size
1st level cache control
2st level cache control
Cache scheme control
System Memory
Item
Memory controller
Memory size
DIMM socket number
Supports memory size per socket
Supports maximum memory size
Supports DIMM type
Supports DIMM Speed
Supports DIMM voltage
Specification
Built-in CPU
1MB for Intel
®
Celeron
®
CPU/2MB for Intel
®
Pentium
®
Always enabled
Always enabled
Fixed in write-back
Specification
Intel ® 915GM/PM or Intel ® 910GML built-in
0MB (no on-board memory)
2 sockets
1024MB
2G (by two 1024MB SO-DIMM module)
DDR Synchronous DRAM
400 MHz/533 MHz
2.5V and 1.25V
22 Chapter 1
System Memory
Item
Supports DIMM package
Memory module combinations
Specification
200-pin soDIMM
You can install memory modules in any combinations as long as they match the above specifications.
Memory Combinations
Slot 1
256MB
256MB
256MB
256MB
512MB
512MB
512MB
512MB
0MB
0MB
0MB
0MB
128MB
128MB
128MB
1284MB
1024MB
1024MB
1024MB
1024MB
1024MB
128MB
256MB
512MB
1024MB
128MB
256MB
512MB
1024MB
128MB
256MB
512MB
1024MB
128MB
256MB
512MB
1024MB
0MB
128MB
256MB
512MB
1024MB
Slot 2
384MB
512MB
768MB
1280MB
640MB
768MB
1024MB
1536MB
128MB
256MB
512MB
1024MB
256MB
384MB
640MB
1152MB
1024MB
1125MB
1280MB
1536MB
2048MB
Total Memory
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be reversed.
LAN Interface
Item
Chipset
Supports LAN protocol
LAN connector type
LAN connector location
Features
Specification
BroadCOM BCM5788M(10/100/1000M) TM3210/TM3220/TM3230;
BCM4401KFB(10/100M)TM2400
10/100/1000Mbps
RJ45
Left side
Integrated 10/100 BASE-T transceiver
Wake on LAN support compliant with ACPI 2.0
PCI v2.2
IR Interface
Item Specification
Part name
Package
VISHAY TFU6102F
8-pin SMT type
Chapter 1 23
24
IR Interface
Performance
Compliant
Item
Modem Interface
Item
Data modem data baud rate (bps)
Supports modem protocol
Modem connector type
Modem connector location
Bluetooth Interface
Item
Chipset
Data throughput
Protocol
Interface
Connector type
4Mbit/s
IrDA 1.1
56K
V.90/V.92
RJ11
Left side
Specification
Specification
Specification built-in Mobile Intel ® 82801FB (ICH6-M)
723 bps (full speed data rate)
Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified).
USB 1.1
Mini-USB
Wireless Module 802.11b/g (optional device)
Item
Chipset
Data throughput
Protocol
Interface
Specification built-in Mobile Intel
®
82801FB (ICH6-M)
11~54 Mbps
802.11b+g
Mini-PCI type II
5-in-1 card reader
Chipset
Protocol
Item Specification
ENE CB712 support MS/MS PRO/MMC/SD/xD
Hard Disk Drive Interface
Item
Vendor &
Model Name
Capacity (MB) 40000
Bytes per sector
512
Data heads
Drive Format
2/2
Disks 1/1
Specification
SEAGATE ST94019A
Toshiba Pluto
MK4025GAS
SEAGATE N2
ST960821A
Toshiba Pluto
MK6025GAS
60000
512
3/4
2/2
SEAGATE N2
ST9808210A
Toshiba Pluto
MK8025GAS
80000
512
4/4
2/2
SEAGATE
ST9100822A
TOSHIBA PLUTO
MK1031GAS
100000
512
4/4
2/2
Chapter 1
Hard Disk Drive Interface
Item
Spindle speed
(RPM)
Specification
4200/4200 RPM
Performance Specifications
Buffer size 2MB/8192KB
Interface
Max. media transfer rate
(disk-buffer,
Mbytes/s)
ATA/ATAPI-6; ATA-6
372
Data transfer rate
(host~buffer,
Mbytes/s)
100 MB/Sec.
Ultra DMA mode-5
DC Power Requirements
Voltage tolerance
5V(DC) +/- 5%
4200/4200 RPM
8192KB
ATA/ATAPI-6; ATA-6
350
8192KB
ATA/ATA-6; ATA-6
350
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
4200/4200 RPM
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
4200/4200 RPM
8192KB
ATA/ATA-6; ATA-6
373
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
Combo Drive Interface
Item
Vendor & model name
Performance Specification
Transfer rate (KB/sec)
Buffer Memory
Interface
Applicable disc format
Loading mechanism
Power Requirement
Input Voltage
Specification
Philips SCB5265+UJDA770
With CD Diskette
Sustained:
Max 3.6Mbytes/sec
With DVD Diskette
Sustained:
Max 10.8Mbytes/sec
2MB
Enhanced IDE(ATAPI) compatible
Read:
DVD: DVD-ROM, (DVD-5, DVD-9, DVD-10, DVD-18), DVD-Video, DVD-R (3.95 and 4.7G), DVD-RW, DVD+R, DVD+RW, Multi-Border DVD-R/DVD-RW, Multi-
Session DVD+R, DVD+RW and DVD-RAM (optional)
CD: CD-DA, CD-ROM Mode-1, CD-ROM/XA Mode-2 Form-1 and Mode-2
Form-2, CD-i Ready, Video-CD (MPEG-1), Karaoke CD, Super Video CD,
Photo-CD, Enhanced CD, CD Plus, CD Extra, i-trax CD, CD-Text, CD-R, CD-
RW
Write:
CD-DA, CD-ROM Mode-1CD-ROM/XA Mode-2 Form-1 and Mode-2 Form-2,
CD-i, Video-CD, CD-Text
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
5 V +/- 5 % (Operating)
DVD-Dual Interface
Item
Vendor & model name
Performance Specification
DVD Dual Pioneer DVR-K15RA
DVD Dual Pioneer DVR-K05RA
LiteOn SOSW-833S
Panasonic UJ-845
With CD Diskette
Specification
With DVD Diskette
Chapter 1 25
26
DVD-Dual Interface
Buffer Memory
Interface
Applicable disc format for LiteOn
SOSW-833S
Item
Transfer rate (KB/sec)
Applicable disc format for
Panasonic UJ-845
Applicable disc format for Pioneer
DVR-K15RA
Applicable disc format for Pioneer
DVR-K05RA
Loading mechanism
Sustained:
Max 3.6Mbytes/sec
2MBytes
Enhanced IDE(ATAPI) compatible
Specification
Sustained:
Max 10.8Mbytes/sec
Read:
DVD: DVD single/dual layer (PTP, OTP), DVD-R (3.9G/4.7G), DVD-R multiborders, DVD-R Double Layer, DVD+R, DVD+R multi-sessions, DVD+R Double
Layer, DVD-RW, and DVD+RW discs with diameter of 8 or 12cm
CD: CD-DA, CD-ROM, CD-ROM/XA, Photo-CD, Multi-session, Karaoke-CD,
Video-CD, CD-I FMV, CD Extra, CD Plus, CD-R, and CD-RW discs of 8 or 12 cm diameter
Read:
DVD: DVD-5, 9,10,18, DVD-R (3.95G/4.7G), DVD-RW, DVD_RAM (4.7G),
DVD+R, DVD+RW
CD: CD-Audio, CD-ROM (mode1 and mode 2), CD-ROM XA (mode 2, form 1 and form 2), CD-I (mode 2, form 1 and form 2), CD-I Ready, CD-I Bridge, CD-R,
CD-RW, Photo CD, Video CD, Enhanced Music CD, CD-TEXT
Write:
DVD: DVD-RAM, DVD-R4.7GB, DVD-RW, DVD+R, DVD+RW
CD: CD-R, CD-RW (disc at once, sessionat once, track at once, fixed/variable packet writing, multi-session)
KODAK Photo CD Single and Multi-session
CD Extra (CD PLUS)
Video CD
CD text data (Read / Write)
CD-R discs (Read / Write)
CD-RW discs (Read / Write)
DVD-ROM
DVD-R Ver.2.00 for General (Read / Write)
DVD-R-DL (Read/Write)
DVD-RW Ver.1.0 & 1.1 & 1.2 (Read / Write)
DVD+R Ver.1.0 & 1.11& 1.2 (Read/Write)
DVD+R -DL Ver1.0 (Read / Write)
DVD+RW Ver.1.1 & 1.2 (Read/Write)
DVD-RAM (Ver.2.0 & 2.1) (Read only)
KODAK Photo CD Single and Multi-session
CD Extra (CD PLUS)
Video CD
CD text data (Read / Write)
CD-R discs (Read / Write)
CD-RW discs (Read / Write)
DVD-ROM
DVD-R Ver.2.00 for General (Read / Write)
DVD-RW Ver.1.0 & 1.1 & 1.2 (Read / Write)
DVD+R Ver.1.0 & 1.11& 1.2 (Read/Write)
DVD+R -DL Ver1.0 (Read / Write)
DVD+RW Ver.1.1 & 1.2 (Read/Write)
DVD-RAM (Ver.2.0 & 2.1) (Read only)
Load: Manual (SOSW-833S/DVR-K15)
Auto (UJ-845/DVR-K05)
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release (Except for UJ-845/DVR-K05)
Power Requirement
Input Voltage 5 V +/- 5 % (Operating)
Chapter 1
Audio Interface
Item
Audio Controller
Audio onboard or optional
Mono or Stereo
Resolution
Compatibility
Mixed sound source
Voice channel
Sampling rate
Internal microphone
Internal speaker / Quantity
Video Interface
Item
Chipset
Package
Interface
Supports ZV (Zoomed Video) port
Video Memory
Chipset
Memory size
Interface
Item
USB Port
Item
Chipset
USB Compliancy Level
OHCI
Number of USB port
Location
Serial port function control
IEEE 1394 Port
Item
Chipset
Number of IEEE 1394 port
Connector type
Chapter 1
Specification
ALC250
Built-in
Stereo
18 bit stereo digital to analog converter
18 bit stereo analog to digital converter
AC97
Line-in, CD
8/16-bit, mono/stereo
44,1 KHz (48K byte for AC97 interface)
Yes
Yes/2
Specification
ATI Mobility RADEON
®
X700 (for discrete models)
MBGA 708 pin
PCIE x16
Yes
Specification
ATI Mobility RADEON
®
X700 (for discrete models)
64MB/128MB
DDR
Specification built-in Mobile Intel ® 82801FB (ICH6-M)
2.0
USB 1.1 and USB 2.0 Host controller
3 two on the left side; one on the rear side
Enable/Disable by BIOS Setup
Specification
TSB34AB21A
1
IEEE 1394
27
28
PCMCIA Port
Item
PCMCIA controller
Supports card type
Number of slots
Access location
Supports ZV (Zoomed Video) port
Supports 32 bit CardBus
System Board Major Chips
Item
Core logic
VGA
LAN
IEEE 1394
USB 2.0
Super I/O controller
Bluetooth
Wireless 802.11 b+g
PCMCIA
Audio
5-in-1 card reader
Keyboard
Item
Keyboard controller
Total number of keypads
Windows logo key
Internal & external keyboard work simultaneously
Specification
ENE CB712
Type-II
One type-II
Left panel
No ZV support
Yes
Controller
Intel
®
915GM/PM (for TravelMate 3210/3220/3230)/Intel
®
910GML (for TravelMate 2400)+Intel
®
ICH6-M (Mobile Intel
82801FB)
ATI Mobility RADEON
®
X700 (for discrete models)
BroadCom BCM4401(10/100M for TravelMate 2400);
BCM5788M(1G for TravelMate 3210/TravelMate 3220/TravelMate
3230)
TSB34AB21A built-in Intel ® ICH6-M (Mobile Intel 82801FB)
SMsC LPC 47N217 built-in Intel ® ICH6-M (Mobile Intel 82801FB) built-in Intel
®
ICH6-M (Mobile Intel 82801FB)
ENE CB712
ALC250
ENE CB712
Specification
KB 910Q
84-/85-key
Yes
1. Plug USB keyboard to the USB port directly: Yes
2. Use port replicator then plug a USB/PS 2 keyboard to the USB port/PS 2 port on the port replicator: Yes
Chapter 1
Battery
Item
Vendor & model name
Battery Type
Pack capacity
Number of battery cell
Package configuration
Normal voltage
Charge voltage
Specification
BATTERY LI-ION 6 CELLS-SANYO
2000mAH UR18650F
BATTERY LI-ION 6 CELLS-SONY
2000mAH US18650G4
BATTERY LI-ION 6 CELLS-SANYO
2400mAH UR18650F
BATTERY LI-ION 6 CELLS-SONY
2400mAH US18650G7
BATTERY LI-ION 9 CELLS-SANYO
2400mAH UR18650F
Li-ion
4800mAh 6cell and 7200mAh 9cell for TravelMate 3210
4000mAh 6cell for TravelMate 2400
53.3W 6cell and 79.9W 9cell for
TravelMate 3210
44.6W 6cell for TravelMate 2400
3 cells in series, 2 series in parallel for 6-cell battery
2 cells in series, 3 series in parallel for 9-cell battery
11.1V
12.6+-0.1v
LCD 14.1 inch
Item
Vendor & model name
Screen Diagonal (mm)
Active Area (mm)
Display resolution (pixels)
Pixel Pitch
Pixel Arrangement
Specification
QDI:
QD14TL01 (Glare)
Surface treatment: glare+hard coating
3H
14.1 inches
303.7x189.8
1280x800 WXGA
0.2373x0.2373
R.G.B. Vertical
Stripe
Normally White
185
Display Mode
Typical White Luminance (cd/m 2 ) also called Brightness
Luminance Uniformity
Contrast Ratio
Response Time (Optical Rise Time/Fall
Time)msec
Nominal Input Voltage VDD
Typical Power Consumption (watt)
Weight
Physical Size(mm)
Electrical Interface
1.25 (5 points)
300
10/15
+3.3V Typ.
N/A
440g
320x206x5.5
1 channel LVDS
QDI
QD14TL01
14.1 inches
303.7x189.8
1280x800 WXGA
0.2373x0.2373
R.G.B. Vertical
Stripe
Normally White
185
1.25 (5 points)
300
10/15
+3.3V
N/A
440g
320x206x5.5
1 channel LVDS
Chapter 1
CMO
N141I1-L03
CMO
N141I1-L02 (nonglare)
14.1 inches
303.3x189.6
1280x800 WXGA
0.2373x0.2373
R.G.B. Vertical
Stripe
Normally White
185
N/A
400
5/11
+3.3V
N/A
425g
320x206x5.5
1 channel LVDS
29
30
LCD 14.1 inch
Item
Support Color
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
Operating
Storage (shipping)
LCD Inverter
Item
Vendor & model name
Brightness conditions
Input voltage (V)
Input current (mA)
Output voltage (V, rms)
Output current (mA, rms)
Output voltage frequency (k Hz)
AC Adaptor
Item
Input rating
Maximum input AC current
Inrush current
Efficiency
System Power Management
ACPI mode
Mech. Off (G3)
Soft Off (G2/S5)
Working (G0/S0)
Suspend to RAM (S3)
Save to Disk (S4)
Specification
262K colors (RGB
6-bit data driver)
45/45
20/35
262,144 262,144
45/45
20/35
45/45
20/45
0 to +40 (with high humidity more than
90%RH)
-25 to +60
0 to +40 (with high humidity more than
90%RH)
-25 to +60
0 to +40 (with high humidity more than
90%RH)
-20 to +60
Delta DAC-07B037 B
YEC YNV-C01
SumidaTWS-442-125
Vadj=3.3V
9~21
350 (max)
1600 (starting voltage)
6.2~6.8 (DAC=0)
45~65K Hz
Specification
Specification
90V AC to 264V AC, 47Hz to 63Hz
1.7A
240A@115VAC
240A@230VAC
83% min. @115VAC input full load
Power Management
All devices in the system are turned off completely.
OS initiated shutdown. All devices in the system are turned off completely.
Individual devices such as the CPU and hard disc may be power managed in this state.
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Also called Hibernate state. System saves all system states and data onto the disc prior to power off the whole system.
Chapter 1
Chapter 1 31
32 Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press
m
during POST (when “Press <F2> to enter Setup” message is prompted on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without entering BIOS SETUP Utility.
Chapter 2 33
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
T
To choose a menu, use the cursor left/right keys (zx).
To choose a parameter, use the cursor up/down keys ( wy).
T
T
T
T
To change the value of a parameter, press por q.
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
Press ^ while you are in any of the menu options to go to the Exit menu.
In any menu, you can load default settings by pressing t. You can also press u to save any changes made and exit the BIOS Setup Utility.
Insyde Software SCU Sep 20, 2005 11:40:09 AM
Main
A dvanced S ecurity B oot E x it
----Devices---------------------------------------------------
Product Name = TravelMate 3210 Light
Manufacture Name = Acer
BIOS Version = V1.00
VGA Version = 3104
HDD Model Name = HTC426040G9AT00
HDD Serial Number = 4EB660
ATAPI Model Name = MATSHITADVD-RAM
UJ-832S
Serial Number = ( 32 bytes)
Asset Tag = (32 bytes)
UUID = (16 bytes)
-----System-------------------------
CPU = Intel® Pentium ® M
CPU speed = 1.73 GHz
L2 Cache = 2048 KB
----Memory------------------------
System Memory = 640 KB
Extended Memory = 247MB
VGA Memory = 8 MB
Setup system date, time. Enable boot logo and get system information.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.
34 Chapter 2
Main
Insyde Software SCU Sep 20, 2005 11:40:09 AM
Main
A dvanced S ecurity B oot E x it
----Devices---------------------------------------------------
Product Name = TravelMate 3210 Light
Manufacture Name = Acer
BIOS Version = V1.00
VGA Version = 3104
HDD Model Name = HTC426040G9AT00
HDD Serial Number = 4EB660
ATAPI Model Name = MATSHITADVD-RAM
UJ-832S
Serial Number = ( 32 bytes)
Asset Tag = (32 bytes)
UUID = (16 bytes)
-----System-------------------------
CPU = Intel® Pentium ® M
CPU speed = 1.73 GHz
L2 Cache = 2048 KB
----Memory------------------------
System Memory = 640 KB
Extended Memory = 247MB
VGA Memory = 8 MB
Setup system date, time. Enable boot logo and get system information.
NOTE: The system information is subject to different models.
Parameter
Product Name
Manufacturer Name
BIOS Version
VGA Version
HDD Model Name
HDD Serial Number
ATAPI Mode Name
Serial Number
Asset Tag
UUID
CPU
Chapter 2
Description
This field displays the prodcut name of the system.
This field displays the manufacturer name of the system
This field displays the BIOS version of the system.
This field shows the VGA firmware version of the system.
This field shows the model name of HDD installed on primary IDE master.
This field displays the serial number of HDD installed on primary IDE master.
This field displays the mofel name of devices installed on secondary IDE master. The hard disk drive or optical drive model name is automatically detected by the system.
This field displays the serial number of this unit.
This field displays the asset tag of this unit.
This will be visible only when an internal LAN device is presenting.
UUID=32bytes
This field shows the brand name of the system CPU.
35
Parameter
CPU speed
L2 Cache
System Memory
Extended Memory
VGA Memory
Description
This field displays CPU L2 cache size. It varies in CPU type.
This field reports the memory size of system base memory. The size is fixed to 640 KB.
This field reports the memory size of the extended memory in the system. Extended memory size = Total memory size - 2MB
VGA Memory size:
Discrete = 64 or 128MB (depends on actual VRAM size)
TurboCache = 32MB (actual TurboCache VRAM size)
Intel(R) 915 DVMT: you can select the following options:
1. 64MB (8MB pre-allocated + 56MB DVMT)
2. 128MB (8MB pre-allocated + 128MB DVMT)-Default value
3. Max DVMT (160MB on 256MB system memory, 224MB on 512 and above system memory).
The Main screen displays a summary of your computer hardware information, and also includes basic setup parameters. It allows the user to specify standard IBM PC AT system parameters.
36
Insyde Software SCU Sep 30, 2005 11:40:09 AM
Main
Date and
T
Advanced Security ime
Boot Exit
Power On Display
----------------Power On Display---------------
ˇ
Q
uiet Boot
ˇ
L
CD Auto DIM
( ˙ ) Auto
( ) Both
ˇ
N
etwork Boot
_ F12 Boot Menu
ˇ D2D
R
ecovery
OK Cancel
Press <Tab> key to select a control. <OK> button or <Enter> key accept entries. <Cancel> button or <Esc> key reject entries. Use cursor, spacebar, and numeric keys to change values. <Alt> key activates accelerators.
NOTE: The screen above is for your reference only. Actual values may differ.
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
Parameter
Date and Time
Quiet Boot
Power on display
LCD Auto Dim
Network Boot
F12 Boot Menu
D2D Recovery
Description
The hours are displayed with 12 hour format. The values setin these two fields take effect immediately.
Determines if the system will display customer logo and summary screen or not.
Enable: Customer logo is displayed, and summary screen is disabled.
Disabled: Custoemr logo is not displayed, and summary screen is enabled.
Auto: During power process, the system will detect if any display device is connected on external video port. If any external display device is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
Determines if the system will automatically dim the LCD brightness in order to save power when
AC is not present.
The system will support an automatic dimming of the LCD backlight when the AC power is NOT available (running on battery power).
Enables, disables the system boot from LAN
(remote server).
Enables, disables Boot Menu during POST.
Enables, disables D2D Recovery function. The function allows the user to create a hidden partition on hard disc drive to store operation system and restore the system to factory defaults.
Format/Option
Option: Enabled or Disabled
Option: Auto or Both
Option: Enabled or Disabled
Option: Enabled or Disabled
Option: Disabled or Enabled
Option: Enabled or Disabled
NOTE: You can also enable Acer disc-to-disc system recovery via Alt+F10 during POST.
Chapter 2 37
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced settings of the system.
Insyde Software SCU Sep 30, 2005 11:40:09 AM
Main
Advanced
Security Boot Exit
--------------------------Infrared Port(FIR)-----------------------
Infrared Port (
F
IR)
Max. Graphics Memory
ˇ Legacy
U
SB Support
-----FIR I/O settings---
(˙) Disabled
( ) Enabled
-Mode Setting for IRDA-
( ) Normal (16550)
( ) IrDA (HPSIR)
( ) ASK IR
(˙) FAST IR
DMA Setting For FIR
( ) DMA1
(˙) DMA2
( ) DMA3
OK Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
The table below describes the parameters in the screen. Settings in boldface are the default and suggested parameter settings.
.
Parameter
Infrared Port
Max Graphics Memory
Legacy USB support
Description
Enables or disables the infrared port.
This option is only available on Intel (R) 915 UMA system.
This feature allows you to USB keyboard entering
BIOS Setup. This feature also allows you to use a
USB keyboard in DOS without additional driver.
USB floppy boot and Crisis Recovery from USB floppy is also supported.
Options
Disabled /Enabled
64MB/ 128MB /DVMT
Enabled /Disabled
38 Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
Insyde Software SCU Sep 30, 2005 11:40:09 AM
Boot Exit
Set User Password
Set Supervisor Password
_ Lock HardDisk Drive --------Set Supervisor password----------------
Enter old Supervisor password: . . . . . . . . . .
Enter new Supervisor Password: . . . . . . . . . ..
Verify new Supervisor Password: . . . . . . . . . .
[ ] Boot System
Enter new password. Password will NOT be displayed
OK Cancel
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings.
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length 10 characters
Characters Alphanumeric keys only. The shift status i.e. Ctrl, Shift, Alt and Capital are ignored.
Parameter
Set User Password
Set Supervisor Password
Lock HardDisk Drive
Description
Press Enter to set the user password. When set, this password protects the BIOS Setup
Utility from unauthorized access.
Press Enter to set the administrator password.
When set, this password protects the BIOS
Setup Utility from unauthorized access.
Allows the user to specify whether or not a password is required to access hard disk drive.
Option
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget your password. If you forget your password, you may have to return your notebook computer to your dealer to reset it.
Chapter 2 39
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
Insyde Software SCU Se[ 30, 2005 11:40:09 AM
Main Advanced Security
Boot
Exit
Boot Device `
----- Boot Device ----
Hard Drive
CD-ROM/DVD Drive
Floppy Device
Network Boot
Press <Tab> key to select a control. <OK> button or <Enter> key accept entries. <Cancel> button or <ESC> key reject entries. Use spacebar and number keys to change value <Alt> key activates accelerators.
40 Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
Insyde Software SCU Sep 30, 2005 11:40:09
Main Advanced Security Boot Exit
Exit Saving Changes
--------------Exit Saving Changes------------------ Exit Discarding Changes
Press <OK> to save the current Load Setup Defaults
Setup parameters to CMOS RAM. Discard Changes
The system will reboot!!!
OK Cancel
<Tab> <Right> <Left> for block select. <Up> <Down> for item select.
< Enter> for accept. <Cancel> <Esc> for reject. <Alt> activates accelerators.
<Space> for Enable or Disable.
The table below describes the parameters in this screen.
Parameter
Exit Saving Changes
Exit Discarding Changes
Load Setup Default
Discard Changes
Description
Exit System Setup and save your changes to CMOS.
Exit utility without saving setup data to CMOS.
Load default values for all SETUP item.
Load previous values from CMOS for all SETUP items.
Chapter 2 41
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
T
New features or options
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not completely loaded.
Fellow the steps below to run the Phlash.
1.
Prepare a bootable diskette.
2.
Copy the Phlash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
42 Chapter 2
Remove BIOS Password
Please find J3 jumper on the main board. Then short the jumper to remove BIOS supervisor password. J3 locates under the memory module. Please see the image below.
42 Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
T
Small Philips screw driver
Philips screwdriver
T
Plastic flat head screw driver
T
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
Chapter 3 43
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Remove the battery pack.
44 Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Start
Battery
*2
Middle Cover
I*4
Lower Case
Assembly
*2
Wireless LAN
Cover
*1
Keyboard
*4
LCD Module
*1
*13
RTC Battery
Bluetooth
Module
Wireless LAN
Cover
ODD Module
HDD Bracket
*3
Upper Case
Assembly
*3
DIMM/HDD
Cover
*4
HDD Module
*4
Memory
HDD
Lower Case
Main Board
Assembly
Fan
Speaker Set
*6
VGA Heatsink
*3
CPU Heatsink
*2
Modem Board
Upper Case
CPU
ODD Module
*2
Touchpad
Bracket
Touchpad
Assembly
Touchpad
ODD ODD Bracket
Chapter 3 45
46
LCD Module
4 screw caps
*4
LCD Bezel
*2 *2
LCD Inverter
LCD Panel
LCD
Assembly
*8
LCD
Screw List
L
M
N
J
K
H
I
F
G
D
E
Item
A
B
C
Description
SCW HEX NYL I#R-40/O#4-40 L5.5
SCREW MACH WAFER M2*L4 NI
CPU SCREW M2.5*6.5 (2.7KG)
CPU SCREW M2.5*6.5 (4.5KG)
SCRW WH MS+CBZ M2.5+L4 BLACK
SCREW M2.5-6
SCREW M2*3 NYLON 1JMCPC-420325
SCREW M2.5X6
SCREW M2-3
SCRW M2.5*L3(NON NYLOK)
SCREW M2.5-5
SCREW M3x4(86.9A524.4R0)
SCREW WAFER NYLOK NI 2ML3
SCREW NI M2*6L
LCD Wire
Cable
LCD Brackets
Chapter 3
Removing the Battery Pack
1.
Unlock the battery lock.
2.
Slide the battery latch then remove the battery.
Chapter 3 47
Removing the Wireless LAN Card/the HDD Module/the Memory/the CPU/ the ODD Module and the LCD Module
Removing the Wireless LAN Card and the HDD Module
1.
Remove the two screws fastening the PCI door.
2.
Detach the PCI door.
3.
Disconnect the wireless antennae.
4.
Pop out the wireless LAN card then remove it.
5.
Remove the two screws fastening the HDD cover.
6.
Remove HDD cover carefully.
7.
Pull the HDD module backwards to disconnect the HDD module then remove it from the main unit.
Removing the Memory and the CPU
1.
Remove the two screws fastening DIMM cover.
2.
Then detach the DIMM cover.
3.
Pop out the memory then remove it from the DIMM socket.
48 Chapter 3
4.
Remove the two screws fastening the thermal door.
5.
Detach the thermal door from the main unit.
6.
Remove the four screws holding the thermal module. (Follow the order indicated by the numbers: 4, 3, 2 then1. Please reverse the order when you assemble the system).
7.
Disconnect the fan cablle as shown.
8.
Take out the thermal module from the main unit carefully.
9.
Use a flat headed screwdriver to release the CPU lock.
10. Then remove the CPU from the CPU socket carefully.
Removing the ODD Module and the LCD module
1.
Remove the screws fastening the ODD module as shown.
2.
Use a flat headed screwdriver to push the ODD module outwards then remove it.
Chapter 3 49
3.
Open the LCD module as shown and detach the middle cover carefully.
4.
Remove the two screws fastening the keyboard.
5.
Turn over the keyboard as shown.
6.
Disconnect the keyboard cable then remove the keyboard.
7.
Tear off the mylard festening the wireless antenna set.
8.
Pull out the wireless antenna from the main unit carefully.
9.
Disconnect the LCD cable from the main board.
50
10. Remove two screws holding the LCD module.
11. Remove another two screws fastening the LCD module on the botton.
12. Then detach the LCD module from the main unit carefully.
Chapter 3
Chapter 3 51
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.
To separate the upper and the lower case assembly, remove six screws as shown.
2.
Turn over the main unit, remove 9 screws on the other side.
3.
Separate the main unit into the upper case assembly and the lower case assembly.
Disassembling the Upper Case Assembly
1.
Disconnect the touchpad FFC from the main board.
2.
Disconnect the bluetooth cable.
3.
Detach the bluetooth module from the upper case.
4.
Disconnect the bluetooth cable from the bluetooth card.
5.
Disconnect the touchpad to touchpad board FFC.
6.
Remove the three screws fastening the touchpad board.
52
7.
Detach the touchpad board.
8.
Remove the four-way button from the upper case.
9.
Remove the two screws fastening the touchpad support to the upper case.
Chapter 3
10. Detach the touchpad support from the upper case carefully.
11. Detach the touchpad from the upper case.
12. Disconnect the FFC from the touchpad.
Disassembling the Lower Case Assembly
1.
Remove four screws fastening the main board to the lower case.
2.
Turn over the lower case assembly, then remove one screw on the other side as shown.
3.
Disconnect the speaker cable.
4.
Detach the main board assembly from the lower case carefully.
5.
Remove the three screws fastening the VGA board.
6.
Disconnect the VGA board assembly from the main board.
7.
Remove the three screws fastening the VGA themal to the VGA board.Detach the main board assembly from the lower case carefully. (Follow the order indicated by the numbers: 3, 2 then1. Please reverse the order when you assemble the system).
Chapter 3 53
54
8.
Detach the VGA thermal from the VGA board.
9.
Disconnect the modem cable from the main board.
10. Remove the two screws fastening the modem board as shwon.
11. Disconnect the modem board from the main board.
12. Disconnect the modem cable from the modem board.
13. Remove the two screws holding the speaker set to the lower case.
14. Take out the speaker set from the lower case. This completes the main unit disassembly.
Chapter 3
Disassembling the LCD Module
1.
Remove the four screw caps as shown.
2.
Remove the four screws holding the LCD bezel.
3.
Then detach the LCD bezel from the LCD module.
4.
Remove the screw fastening the LCD inverter.
5.
Disconnect the LCD cable and disconnect the inverter cable, then remove the inverter.
6.
Remove the two screws fastening the LCD assembly to the LCD panel.
.
7.
Take out the LCD assembly from the LCD panel.
8.
Remove the four screws fastening the LCD left bracket then remove it.
9.
Remove the four screws fastening the LCD right bracket.
10. Then remove the LCD right bracket.
11. Tear off the mylar and disconnect the LCD cable from the LCD then remove the cable.
Chapter 3 55
Disassembling the External Modules
Disassembling the HDD Module
1.
Remove the two screws holding the HDD bracket on one side.
2.
Remove another two screws holding the HDD bracket on the other side.
3.
Then take the hard disc drive out of the HDD bracket.
Disassembling the ODD Module
1.
Remove the two screws fastening the ODD bracket.
2.
Remove the ODD bracket from the optical disc drive module.
56 Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses.
1.
Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.
Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation.
3.
Disassemble and assemble the unit without any power sources.
4.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You can check the following: power cords are properly connected and secured; there are no obvious shorts or opens; there are no obviously burned or heated components; all components appear normal.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Power failure. (The power indicator does not go on or stay on.)
POST does not complete. No beep or error codes are indicated.
POST detects an error and displayed messages on screen.
Other symptoms (i.e. LCD display problems or others).
Symptoms cannot be re-created (intermittent problems).
Go To
“Power System Check” on page 59.
“Insyde MobilePro BIOS POST Beep Code and
“Insyde MobilePro BIOS POST Codes” on page
“Undetermined Problems” on page 72
“Insyde MobilePro BIOS POST Beep Code and
“Insyde MobilePro BIOS POST Codes” on page
“Insyde MobilePro BIOS POST Beep Code and
“Insyde MobilePro BIOS POST Codes” on page
“Index of Symptom-to-FRU Error Message” on page 67
Use the customer-reported symptoms and go to
“Insyde MobilePro BIOS POST Beep Code and
“Insyde MobilePro BIOS POST Codes” on page
“Intermittent Problems” on page 71
“Undetermined Problems” on page 72
Chapter 4 57
System Check Procedures
External Diskette Drive Check
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4.
Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
58 Chapter 4
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
“Check the Battery Pack” on page 60
Chapter 4 59
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light up, replace the DC/DC charger board.
Touchpad check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a non-defective FRU:
1.
After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the the PS/2 mouse does not work, then check if the main board to switch board FPC is connected O.K.
4.
If the main board to switch board FPC is connected well, then check if the FCC on touch pad PCB connects properly.
5.
If the FFC on touch pad PCB connects properly, then check if LS851 JP1 Pin6=5V are pulese. If yes, then replace switch board. If no, then go to next step.
6.
Replace touch pad PCB.
7.
If the touch pad still does not work, then replace FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware problem. No service actions are necessary if the pointer movement stops in a short period of time.
60 Chapter 4
Insyde MobilePro BIOS POST Beep Code and POST Messages
The POST error message index lists the error message and their possible causes. The most likely cause is listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 72.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Beep Code short, short, short; short, short, long short, short, short; short, long, short short, short, short; short, long, long short, short, short; long, short, short short, short, short; long, short, long short, short, short; long, long short short, short, short; long, long, long
Message
“FAULTY DMA PAGE REGISTERS”
“FAULTY REFRESH CIRCUIT”
“ROM CHECKSUM INCORRECT”
“CMOS RAM TEST FAILED”
“DMA CONTROLLER FAULTY”
“INTERRUPT CONTROLLER
FAILED”
N/A short, short, long; short, short, short short, short, long; short, short, long
N/A
N/A
N/A
“KEYBOARD CONTROLLER
FAILURE”
N/A “KEYBOARD FAILURE”
N/A
N/A
N/A
N/A
N/A
Description
DMA page registers do not function properly.
RAM refresh circuit does not function properly.
BIOS ROM checksum failed.
CMOS RAM test failed.
DMA controller does not work properly.
The interrupt controller does not work properly.
Keyboard controller failed to respond with the self-test command.
No video device found.
No RAM installed.
“CMOS FAILURE - RUN SCU”
“CMOS CHECKSUM INVALID - RUN
SCU”
“RAM ERROR AT LOCATION xxxxxx:
WROTE: xxxx
READ: xxxx”
“PARITY ERROR AT UNKNOWN
LOCATION”
“PARITY ERROR AT LOCATION
XXXXXX”
Keyboard controller failed during system inquiry about connected devices.
The keyboard fails to respond or no keyboard is connected.
CMOS data error, probably due to battery power loss.
CMOS checksum error.
The RAM failed during memory test at the indicated location.
Parity error during memory test at unknown location.
Parity error during memory test at the indicated location.
Chapter 4 61
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Beep Code Message
“NO INTERRUPTS FROM TIMER 0”
Description
Timer 0 of the clock timer controller does not generate system interrupts correctly.
“UNEXPECTED AMOUNT OF
MEMORY - RUN SCU”
The system memory size does not match with the CMOS record.
“CLOCK NOT TICKING CORRECTLY” The system clock does not working correctly.
“TIME/DATA CORRUPT - RUN SCU” The time/date information in CMOS is invalid.
“MACHINE IS LOCKED - TURN KEY” The keyboard operation is locked.
“BOOT SECTOR 0 HAS CHANGED” The boot sector of the hard disk has been changed, probably because of a virus attack.
Suspend-to-Disk partition MISSING!” No Suspend-to-Disk partition found.
“Hard Disk ERROR!” Access to the Suspend-to-Disk partition failed.
No Suspend-to-Disk partition signature found.
“Suspend-to-Disk partition signature
NOT FOUND!”
“Suspend-to-Disk partition size TOO
SMALL!”
“MEMORY SIZE HAS CHANGED --
REBOOTING”
The capacity of the Suspend-to-Disk partition is not enough.
The memory size has changed after previous
Suspend-to-Disk operation.
62 Chapter 4
Insyde MobilePro BIOS POST Codes
POST Code
Boot Loader--BLOAD.ASM
00
01
02
03
04
05
06
Macro Name
DIAG_SYSTEM_INIT
DIAG_A20_DISABLE
DIAG_INIT_CHIPSET
DIAG_TEST_RAM
DIAG_MOVE_BB_LOADER
DIAG_EXECUTE_IN_DRAM
DIAG_USER_FLASH_CHECK
Description
07
08
09
0A
15
16
17
18
19
1A
1B
1C
1D
1E
DIAG_SHADOW_BIOS
DIAG_CHECKSUM_BIOS
DIAG_NORMAL_BOOT
DIAG_CRISIS_BOOT
Boot started, check motherboard power is stable.
Disable A20 through A20
Initialize Chipset
Test the basic 640k RAM
Move boot load segment into the RAM program execution from DRAM
Test print port for check crisis option is enable or disable
Decompress the system BIOS, and Shadow
System BIOS to RAM
Checksum System BIOS ROM
Jump to the reset point
Proceed with Crisis Boot, first initial super I/O and boot device
Fatal Error, like the RAM error or ROM error
Start process the Crisis recovery procedure
Resume SMRAM not Found
0F
CC
DIAG_FATAL_ERROR
DIAG_CRISIS_BEGIN
99 DIAG_RESUME_RAM_ERROR
POST DIAG -- BIOSPINE.ASM
10
11
DEBUG_MISC_RESET
DEBUG_CS_FAST_A20_RESET
12
13
14
1F
20
21
22
DEBUG_POST_SIGNAL_POR
DEBUG_CS_CHIP_INIT
DEBUG_OEM_ISA_VGA_SEARCH
DEBUG_HWIO_SETUP_CTC1
DEBUG_OEM_SET_CMOS_REGS
DEBUG_CS_MEMORY_SIZE
DEBUG_POST_TEST_RAM
DEBUG_GEN_TEST_ROMS
DEBUG_HWIO_RESET_INTS
DEBUG_VIDEO_VIDEO_INIT
DEBUG_VIDEO_EQUIP_INIT
DEBUG_VIDEO_COLOR_INIT
DEBUG_VIDEO_BW_INIT
DEBUG_HWIO_TEST_DMA_PAG
Disable internal cache ram, and reset cpu
Turn off FASTA20 for post, and check have keyboard
Initial PIC enable INT and Signal Power On
Reset
Initialize the Chipset and hook PCI BIOS
Search For ISA Bus VGA Adapter, from address c000 to e000
Initialize Counter and Timer chip
User register config through CMOS
Size Memory, and detect memory timing, setup memory controllor
Initialize and test the first 64k memory checksum the system ROM
Reset PIC's status
Initialize Video Adapter(s),and check vga rom and vga ram
Initialize Video (6845 Regs),set display mode
Initialize Color Adapter, and setup display reg.
Initialize Monochrome Adapter, and setup display reg.
Send out some value, to test 8237A Page
Registers
DEBUG_KEYB_SELFTEST_CTLR
DEBUG_POST_CHECK_CMOS_RA
M
Send self test command (AAH) to test Keyboard controller. If o.k. return (55h)
DEBUG_KEYB_RESET_KEYBOARD Test Keyboard Controller and initialize keyboard controller.
Send test petten to Check CMOS Ram
Chapter 4 63
64
23
24
28
29
2A
2B
25
26
27
32
33
2C
2D
2E
2F
30
31
POST Code
3F
40
41
42
43
3B
3C
3D
3E
34
35
36
37
38
39
3A
Macro Name
DEBUG_POST_TEST_BATT_CMOS_
SUM
Description
Test Battery Fail & check CMOS X-SUM
DEBUG_HWIO_TEST_DMA_CTLRS Use DMA to copy data for Test the DMA controllers
DEBUG_HWIO_INIT_8237
DEBUG_POST_INIT_VECS
DEBUG_RAM_QUICK_SIZE
Initialize 8237A Controller
Install and Initialize interrupt Vectors
Enter memory protect mode, use change RAM bank to do RAM Quick Sizing
DEBUG_RAM_PROT_ENTRY_1
DEBUG_RAM_SIZE_DONE
DEBUG_RAM_PROT_EXIT
DEBUG_CS_SHADOW_SETUP
DEBUG_VIDEO_EQUIP_INIT_INIT
DEBUG_VIDEO_BW_SEARCH
DEBUG_VIDEO_COLOR_SEARCH
DEBUG_VIDEO_SIGNON
DEBUG_OEM_CONFIG_KBD_CTL
DEBUG_KEYB_PRESENT_TEST
Memory protected mode entered safely
Test the basic 640k ram , RAM test completed
Protected mode exit successful
Shadow system and video BIOS to RAM, if
CMOS requests shadow
Going To Initialize 6845 CRT controllor
Search For Monochrome Adapter
Search For Color Adapter
Signon messages displayed
DEBUG_KEYB_TEST_IRQ1
DEBUG_KEYB_TEST_CMD
DEBUG_RAM_FULL_TEST
DEBUG_RAM_PROT_ENTRY_2
DEBUG_RAM_TEST_DONE
DEBUG_RAM_PROT_EXIT_2
For special initialize of keyboard controller
Test the keyboard controllor , If Keyboard
Present
Clear keyboard buffer and send keyboard command to test Keyboard Interrupt
Send keyboard command to turn off keyboard
LED and Test some Keyboard Command Byte
TEST memory procedure, for test, blank and count all RAM
Eneter the memory protected mode for test all expand memory
Test and blank all memory complete
DEBUG_KEYB_OUTPUT_PORT
DEBUG_CS_CACHE_SETUP
DEBUG_HWIO_TEST_PERIODIC
DEBUG_GEN_CHECK_RTC
DEBUG_GEN_INIT_HARD_VECS
DEBUG_MOUSE_INIT
DEBUG_KEYB_SET_LEDS_1
DEBUG_OEM_DEVICE_CONFIG
DEBUG_CS_CONFIG_PORTS
DEBUG_FLOP_INIT
DEBUG_WINI_INIT
DEBUG_HWIO_ROM_INIT
Switch the memory from Protected mode to real mode
Disable A20 status for memory test finish
Setup Cache Controller
Check and test the timer 0 interrupt function is
Working test for RTC ticking
Install and initialize the hardware vectors
Clear keyboard buffer for search and Init the
Mouse
Send keyboard command to Update keyboard
NUMLOCK status special init of COMM and LPT ports
Configure the COMM and LPT ports
According cmos data to initialize the floppies
Scan and initialize the hard disk, and display the result n crt
Search option rom from c800 to e000 and to
Initialize option ROMs
Chapter 4
DE
DF
E0
E1
E2
E3
E4
D4
D5
D6
D7
D8
D9
DA
44
45
46
47
48
49
50
51
52
POST Code Macro Name
DEBUG_OEM_INIT_POWER_MAN
DEBUG_KEYB_SET_LEDS_2
DEBUG_HWIO_FIND_80X87
DEBUG_OEM_LAST_MINUTE_INIT
DEBUG_MISC_LAUNCH_INT19
DEBUG_BEGIN_BOOT_CODE
DEBUG_ACPI_INIT
DEBUG_PM_CPU_INIT
DEBUG_USB_HC_INIT
Description
Check special device initial power management function
Clear keyboard buffer and Update NUMLOCK status
Test For Coprocessor Installed, and enable coprocessor interrupt
Run OEM functions before boot, and enable
L1,L2 cache
Post code will finish, ready to run int19 and load
OS
Into Int19, to boot from floppy or other boot device
Initialize the ACPI function
Power manager initial & GEYSERVILLE CPU initialize
Clear USB status register and Initiallize the USB
Hub controller.
PCI BIOS -- PCICORE.ASM
D0 DEBUG_ROM_MAPPED_OK
D1
D2
D3
DB
DC
DD
DEBUG_SEGMENTENABLE_
COPYSTATE_1
DEBUG_COPY_HROM_RAM_1
DEBUG_SEGMENTENABLE_
READWRITE_1
DEBUG_MAP_MEM_1
DEBUG_MAP_IO_1
DEBUG_MAP_IRQ_1
DEBUG_CONFIG_COM_REG_1
DEBUG_REVISION_1
DEBUG_OEM_DEV_CLEANUP_1
DEBUG_PCI_ADDIN_ROM_
DISABLE_1
DEBUG_RET_PCI_1
DEBUG_SEGMENTENABLE_
COPYSTATE_2
DEBUG_COPY_HROM_RAM_2 check PCI 1.x VGA card rom mapping and rom signature enable PCI device use ram area, record in PCI register
Enable PCI device ROM copy to RAM, record in
PCI register update PCI device segment range attribute registers
Configure PCI device memory registers
Configure PCI device I/O registers
Configure PCI device IRQ assignments turn on PCI device
PCI 2.x video card rom mapping
OEM PCI device defined, and initial OEM rom disable add-in rom card decode
E5
DEBUG_SEGMENTENABLE_
READWRITE_2
DEBUG_MAP_MEM_2
DEBUG_MAP_IO_2
DEBUG_MAP_IRQ_2
DEBUG_CONFIG_COM_REG_2
DEBUG_REVISION_2
DEBUG_OEM_DEV_CLEANUP_2
DEBUG_PCI_ADDIN_ROM_
DISABLE_2
PCI device config finish enable PCI video device use ram area, record in
PCI register
Enable PCI video device ROM copy to RAM, record in PCI register update PCI video device segment range attribute registers configure PCI video device memory registers configure PCI video device I/O registers configure PCI video device IRQ assignments turn on PCI video device
PCI 2.x video rom mapping
OEM PCI video device defined, and initial OEM rom disable PCI video device add-in rom card decode
Chapter 4 65
66
E6
E7
E8
POST Code Macro Name
DEBUG_RET_PCI_2
DEBUG_BRIDGE_HUNT
DEBUG_PCI_IDE_FIND
Description
PCI device config finish
Search for PCI bridge controllor device
Search IDE controllors on the PCI bus, and config the IDE controllors start of cardbus config E9
PNP BIOS -- PNPINIT.ASM
A1
A2
A3
A4
C5
DEBUG_CB_CONFIG
DEBUG_PNP_ENABLE_VERIFY_RT
DATA
DEBUG_PNP_GET_VERIFY_NVRAM Get and Verify R/W Status for PNP BIOS
NVRAM data area
DEBUG_PNP_SYSTEM_NODES
DEBUG_PNP_INITIALIZE_RTDATA
Enable and Verify R/W Status for PNP BIOS
Runtime Data Area
Resolve System Nodes with the CMOS settings
Initialize variable in the PNP BIOS Runtime Data area
DEBUG_PNP_HOOK_INT15
DEBUG_PNP_SET_COPY_AREA
Hook INT 15 copy and setup PnP BIOS sytem node
A5
A6
A7
A8
DEBUG_PNP_OEM_LATE_HOOK
DEBUG_PNP_WRITE_PROTECT_R
T_DAT
A9 DEBUG_PNP_INIT_RETURN
General SMI Entry/Exit Code -- SMICHIP.ASM
C0
C1 dSMI_ENTRY dSMI_EXIT
C2
C3 dSMI_APM_ENTRY dSMI_APM_EXIT
Software SMI request Codes -- SWSHELL.ASM
C4 dSMI_SWEXEFN dSMI_HWEXEFN
Allow the OEM any Last Minute Hooks
Write protect RTData Area and NVRAM Copy
Buffer, and make runtime data checksum
PNP BIOS initialize finish
SMI procedure entry point
SMI procedure exit
APM MODE SMI procedure entry point
APM MODE SMI procedure exit
SoftWare SMI function execution
HardWare SMI function execution
Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
LCD is too dark
LCD brightness cannot be adjusted
Unreadable LCD screen
Missing pels in characters
Abnormal screen
Wrong color displayed
LCD has extra horizontal or vertical lines displayed.
Action in Sequence
First, plug a monitor to CRT port. Next, enter BIOS utility to running
“Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Reconnect the LCD cable
LCD cable
LCD
Main board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system runs correctly
HDD/CD-ROM active indicators cannot work
Main board
HDD/CD-ROM drive
Device driver
Main board
Action in Sequence
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
The system cannot power-on.
The system cannot power-off.
Action in Sequence
Power source (battery pack and power adapter). See “Power
Battery pack
AC adapter
See if the thermal module is overheat (Heat sink or fan).
Main board
Power source (battery pack and power adapter). See “Power
Battery pack
Power adapter
CPU
Main board
In Windows XP operating system, hold and press the power switch for more than 4 seconds. If the system can power off, then the main board is OK. Verify OS in the HDD.
Main board
Chapter 4 67
68
Power-Related Symptoms
Symptom / Error
Battery can’t be charged or discharged
System hang during POST
Action in Sequence
See “Check the Battery Pack” on page 60.
Battery pack
Main board
ODD/HDD/FDD/RAM module
Main board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
PCMCIA slot pin is damaged.
PC Card cannot be inserted or ejected
Action in Sequence
PCMCIA slot assembly
Main board
PCMCIA slot assembly
Check if the PCMCIA slot is blocked
Main board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from actual size.
System can power on, but you hear two long beeps: “B--, B--” and the LCD is blank.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings” then reboot system.
RAM module
Main board
Check BIOS revision
Reinsert DIMM
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound comes from the computer.
OS volume control
Audio driver
Speaker
Main board
Action in Sequence
Internal speakers make noise or emit no sound.
Speaker
Main board
Microphone cannot work Audio driver
Volume control in Windows XP
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation mode
The system doesn’t enter standby mode after closing the lid of the portable computer.
Action in Sequence
Power option in Windows XP
Hard disk drive
Main board
Driver of Power Option Properties
Lid close switch in upper case
Main board
Chapter 4
Power Management-Related Symptoms
The system doesn't resume from hibernation/ standby mode.
Symptom / Error
The system doesn't resume from standby mode after opening the lid of the portable computer.
Battery fuel gauge in Windows doesn’t go higher than 90%.
System hangs intermittently.
Action in Sequence
Connect AC adapter then check if the system resumes from
Standby/Hibernation mode.
Check if the battery is low.
Hard disk drive
Main board
LCD cover switch
Main board
Refresh battery (continue use battery until power off, then charge battery).
Battery pack
Main board
Reconnect hard disk/CD-ROM drives.
Main board
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the installed devices.
External display does not work correctly.
USB does not work correctly
Print problems.
Parallel port device problems
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then reboot system.
Reconnect hard disk/CD-ROM drives/FDD or other peripherals.
Main board
Press Fn+F5, LCD/CRT/Both display switching
Keyboard
Main board
Main board
Enter BIOS Setup Utility to execute “Load Default Settings” then reboot the system.
Run printer self-test.
Printer driver
Printer cable
Printer
Main board
Enter BIOS Setup Utility to execute “Load Default Settings” then reboot the system.
Device driver
Device cable
Device
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Touchpad does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Reconnect touchpad cable.
Touchpad board
Main board
Chapter 4 69
Modem/LAN-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Internal LAN does not work correctly
Action in Sequence
Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Lan cable
Driver
Main board
70 Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1.
Run the diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4 71
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
T
T
T
Printer, mouse, and other external devices
Battery pack
Hard disk drive
DIMM
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
T
System board
T
LCD assembly
72 Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
SW3
JP1
SW2
SW4 SW5 SW6
SW1
2
2
JP7
2
2
JP4
2
JP5
2
JP42
KQ:
2
2
SW3
JP1
SW2
SW4
SW5
SW6
Power Switch
Bluetooth Connector
E-mail Switch
Internet Browser Switch
Emanager Switch
User Programmable Switch
SW1
JP5
JP4
JP42
JP7
JP10
Lid Swtich
Touchpad Connector
Keyboard Connector
Speaker Connector
PCMCIA Slot
Microphone Connector
Chapter 5 73
Bottom View
2
JP21
2
PJP11
JP20
JP39
JP26
JP31
2
JP16
2
JP22
PCN1
2 JP13 JP12
JP14
2
JP19
2
JP3
2
JP17
2
2
2
JP35
2
T2
JP28
Q2 JP29
JP36
2
JP23
JP24
2
JP25
2
JP30
2
U42
2
JP41
JP40
74
JP13
JP12
JP14
JP3
JP17
JP19
JP23
JP21
PJP11
JP20
JP16
JP22
PCN1
Fan Connector
Battery Connector
CPU Socket
LVDS Connector
VGA Board Connector
AC-IN
USB Port
Acer ezDock (TravelMate 3220 only)
Modem Board Connector
External Display Port
S-Video Port
RJ11/RJ45
Modem Cable Connector
JP41
JP28
JP35
U42
JP26
JP31
JP39
JP24
JP25
JP30
JP36
IR
JP40
USB Port
USB Port
IEEE 1394 Port
Card Reader Connector
Infrared Receiver
Headphone out/line-out Jack
(support SPDIF)
Mic-in Jack
HDD Connector
Wireless LAN Card Connector
BIOS
DDR2 Socket
DDR2 Socket
ODD Connector
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 2400/
3210/32203230 series products. Refer to this chapter whenever ordering for parts to repair or for RMA (Return
Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 75
Exploded Diagram
The System
011
012
013
76 Chapter 6
Upper Case Assembly
Chapter 6 77
Lower Case Assembly
78 Chapter 6
LCD Module
Chapter 6 79
HDD Module
ODD Module
80
NOTE: Below is TravelMate 2400/3210/3220 FRU List. The columns highlighted in blue indicate the differential parts for TravelMate 3220.
Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Adapter
Picture No.
Part Name and Description
NS (Not
Show)
ADAPTER 3 PIN 65W DELTA SADP-65KB
BEF 19V 3PIN
ADAPTER 3 PIN 65W LITEON PA-1650-02CO
65W 3 PIN
ADAPTER 3 PIN 65W HIPRO HP-
OK066B13CP 3P 65W
Battery
NS
NS
BATTERY LI-ION 6 CELLS-SANYO 2000mAH
UR18650F
BATTERY LI-ION 6 CELLS-SONY 2000mAH
US18650G4
BATTERY LI-ION 6 CELLS-SANYO 2400mAH
UR18650F
BATTERY LI-ION 6 CELLS-SONY 2400mAH
US18650G7
BATTERY LI-ION 9 CELLS-SANYO 2400mAH
UR18650F
Board
The
System-
012
MODEM BOARD FOXCONN T60M845.01
Part Number
AP.06501.006
AP.06503.007
AP.0650A.004
BT.00603.001
BT.00604.004
BT.00604.001
BT.00604.001
BT.00903.002
54.A70V5.001
NS BLUETOOTH CARD WNC 91.BU513.002
54.A70V5.002
NS MINI PCI WIRELESS BOARD 802.11 b+g
INTEL WM3B2200/CH11
KI.CAX01.008
Upper
Case
Assembly-
251
T/P BOARD W/FFC CABLE 55.A70V5.001
Chapter 6 81
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
The
System-
013
Part Name and Description
VGA BOARD M26P 64MB
Part Number
55.A70V5.002
Cable
Upper
Case
Assembly-
004
NS
FFC CABLE - T/P TO T/P BOARD
BLUETOOTH CABLE
50.A70V5.001
50.A70V5.002
NS MODEM CABLE 50.A70V5.003
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
CABLE NS
Case/Cover/Bracket Assembly
The
System-
006
POWER CORD-AUS
POWER CORD-CHINA
POWER CORD-DENMARK
POWER CORD-EC
POWER CORD-INDIA
POWER CORD-ISREL
POWER CORD-ITALIAN
POWER CORD-JP
POWER CORD-KOREA
POWER CORD-SOUTH AFRICA
POWER CORD-SWISS
POWER CORDTWN
POWER CORD-UK
POWER CORD-US
MIDDLE COVER - TM
27.A70V5.001
27.A70V5.002
27.A70V5.003
27.A70V5.004
27.A70V5.005
27.A70V5.006
27.A70V5.007
27.A70V5.008
27.A70V5.009
27.A70V5.010
27.A70V5.011
27.A70V5.012
27.A70V5.013
27.A70V5.014
42.TAAV5.001
82 Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
The
System-
254;
Upper
Case
Assembly-
001
Part Name and Description
UPPER CASE-TM
NS
The
System-
002
UPPER CASE FOR DUCKING(TravelMate
3220)
LOWER CASE- UMA
Part Number
60.TAAV5.001
60.TAMV5.001
60.A70V5.002
NS
NS
Upper
Case
Assembly-
002
Upper
Case
Assembly-
003
LOWER CASE- NON UMA
LOWER CASE FOR DUCKING(TravelMate
3220)
4 - WAY BUTTON
TP SUPPORT
60.A70V5.003
60.TAMV5.002
42.A70V5.002
33.A70V5.001
42.A70V5.003
Lower
Case
Assembly-
003
DIMM COVER
Lower
Case
Assembly-
004
PCI DOOR 42.A70V5.005
Lower
Case
Assembly-
005
THERMAL DOOR 42.A70V5.006
Communication Module
NS
CPU/Procussor
Chapter 6
ANTENNA ASSY 50.A70V5.004
83
TravelMate 2400/3210/3220/3230 FRU List
Picture
NS
NS
NS
NS
No.
NS
NS
NS
NS
Part Name and Description
CELERON M 350 (1.3G 1M) C0
CELERON M 360 (1.4G 1M) C0
CELERON M 370 (1.5G 1M) C0
INTEL PENTIUM M DOTHAN 1.6GHZ 2M
UFCBGA SL7EG B-1 STEPPING
INTEL PENTIUM M 1.6G 2M 533FSB uFCPGA2 SL86G C-1 STEPPING
INTEL PENTIUM M 1.73G 2M 533FSB uFCPGA2 SL7SA C-1 STEPPING
INTEL PENTIUM M 1.87G 2M 533FSB uFCPGA2 SL7S9 C-1 STEPPING
INTEL PENTIUM M 2.0G 2M 533FSB uFCPGA2 SL7SM C-1 STEPPING
Combo Drive
ODD
Module
DVD/CDRW COMBO MODULE 24X PHILIPS
SCB5265
Part Number
KC.NC001.350
KC.NC001.360
KC.NC001.370
KC.N0001.725
KC.N0001.730
KC.N0001.740
KC.N0001.750
KC.N0001.760
6M.A70V5.001
ODD
Module-
001
ODD
Module-
002
ODD
Module-
003
DVD/CDRW COMBO DRIVE 24X PHILIPS
SCB5265
DVD/CDRW COMBO BEZEL
ODD BRACKET
KO.02403.007
42.A70V5.007
33.A70V5.002
DVD RW Drive
ODD
Module
ODD
Module-
001
ODD
Module-
002
ODD
Module-
003
ODD
Module
ODD
Module-
001
DVD/CDRW COMBO 24X MODULE
PANASONIC UJDA-770
DVD/CDRW COMBO 24X DRIVE
PANASONIC UJDA-770
DVD/CDRW COMBO BEZEL
ODD BRACKET
6M.A70V5.002
KO.02406.013
42.A70V5.007
33.A70V5.002
DVD DUAL MODULE 8X LITE-ON SOSW-
833S (DL) TRAY IN
DVD DUAL 8X DRIVE LITE-ON SOSW-833S
(DL)
6M.A70V5.004
KU.00804.012
84 Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
ODD
Module-
002
ODD
Module-
003
Part Name and Description
DVD DUAL BEZEL - TRAY IN
ODD BRACKET
HDD Module
ODD
Module
ODD
Module-
001
ODD
Module-
002
ODD
Module-
003
ODD
Module
ODD
Module-
001
ODD
Module-
002
ODD
Module-
003
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
HDD
Module
ODD BRACKET
SUPER MULTI MODULE 8X PANASONIC UJ-
840BAA (DL)
SUPER MULTI 8X DRIVE PANASONIC UJ-
840BAA
SUPER MULIT BEZEL
6M.A70V5.008
KU.00807.011
42.A70V5.010
ODD BRACKET
Part Number
42.A70V5.008
33.A70V5.002
DVD DUAL MODULE 8X HLDS GWA-4082N
(DL)
DVD DUAL 8X DRIVE HLDS GWA-4082N
(DL)
DVD DUAL BEZEL - TRAY IN
6M.A70V5.007
KU.0080D.016
42.A70V5.008
33.A70V5.002
33.A70V5.002
HDD 40G 4200PRM SEAGATE ST94019A KH.04001.010
HDD 40G 2.5 IN. 420RPM TOSHIBA PLUTO
MK4025GAS
HGST 40G 2.5" 4200 MORAGA+
HTS424040M9AT00 13G1132 FW:A71A
HDD 60GB 2.5 IN. 4200RPM SEAGATE N2
ST960821A F/W: 3.01
HDD 60G 2.5IN. 4200RPM TOSHIBA PLUTO
MK6025GAS 2M F/W KA200A
HDD 60GB 2.5IN. 4200RPM MORAGA 60G
IC25N060ATMR04-0 08K0634 F/S:AD4A
HDD 80GB 2.5 IN. 4200RPM SEAGATE N2
ST9808210A F/W: 3.01
HDD 80GB 2.5IN. 4200RPM TOSHIBA
PLUTO MK8025GAS
HDD 80GB 2.5IN. 4200RPM HGST MORAGA
IC25N080ATMR04-0
HDD 100G 4200PRM SEAGATE ST9100822A
F/W:3.01
HDD 100GB 2.5IN. 4200RPM TOSHIBA
PLUTO MK1031GAS F/W AA20
KH.04004.002
KH.04007.012
KH.06001.002
KH.06004.003
KH.06007.006
KH.08001.012
KH.08004.001
KH.08007.007
KH.10001.001
KH.10004.001
Chapter 6 85
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
HDD
Module-
001
Part Name and Description
HDD BRACKET
Lower
Case
Assembly-
008
HDD DOOR
Keyboard
LCD Module
Part Number
33.A70V5.003
42.A70V5.011
The
System-
011
LCD
Module
LCD
Module-
001
KEYBOARD DARFON CHINESE
KEYBOARD DARFON US INTERNATIONAL
KEYBOARD DARFON THAI
KEYBOARD DARFON GERMAN
KEYBOARD DARFON UK
KEYBOARD DARFON ITALIAN
KEYBOARD DARFON FRENCH
KEYBOARD DARFON SWISS/G
KEYBOARD DARFON BELGIUM
KEYBOARD DARFON SPANISH
KEYBOARD PORTUGUESE
KEYBOARD CZECH
KEYBOARD HUNGARIAN
KEYBOARD RUSSIAN
KEYBOARD SWEDEN
KEYBOARD NORWEGIAN
KEYBOARD DANISH
KEYBOARD ARABIC
KEYBOARD BRAZILIAN PORTUGUESE
KEYBOARD CANADIAN FRENCH
KEYBOARD GREEK
KEYBOARD TURKISH
KEYBOARD HEBREW
KEYBOARD SLOVENIA/CROATIA)
KB.T5902.001
KB.T5902.002
KB.T5902.003
KB.T5902.004
KB.T5902.005
KB.T5902.006
KB.T5902.007
KB.T5902.008
KB.T5902.009
KB.T5902.010
KB.T5902.011
KB.T5902.012
KB.T5902.013
KB.T5902.014
KB.T5902.015
KB.T5902.016
KB.T5902.017
KB.T5902.018
KB.T5902.019
KB.T5902.020
KB.T5902.021
KB.T5902.022
KB.T5902.023
KB.T5902.024
ASSY LCD MODULE 14 .1 WXGA NON
GLARE QDI (N141V2 QD14TL01 REV 01) W/
ANT - TM
LCD 14 .1 WXGA NON GLARE QDI N141V2
QD14TL01 REV 01
6M.TAAV5.003
LK.14109.004
86 Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
LCD
Module-
007
Part Name and Description
LCD INVERTER
LCD
Module-
006
LCD WIRE CABLE
Part Number
19.A70V5.001
50.A70V5.005
LCD
Module-
004
LCD PANEL WITH LOGO W/ANTENNA - TM 60.TAAV5.002
LCD
Module-
005
LCD BEZEL
LCD
Module-
002, 003
LCD BRACKET SET
60.A70V5.006
6K.A70V5.001
LCD
Module
LCD
Module-
001
ASSY LCD MODULE 14.1 WXGA NON
GLARE CMO (N141l 1-L03) W/ANT-TM
LCD 14.1 WXGA NON GLARE CMO (N141l 1-
L02)
6M.TAAV5.004
LK.1410D.004
LCD
Module-
007
LCD INVERTER 19.A70V5.001
Chapter 6 87
88
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
LCD
Module-
006
Part Name and Description
LCD WIRE CABLE
Part Number
50.A70V5.005
LCD
Module-
004
LCD PANEL WITH LOGO W/ANTENNA - TM 60.TAAV5.002
60.A70V5.006
LCD
Module-
005
LCD BEZEL
LCD
Module-
002, 003
LCD BRACKET SET 6K.A70V5.001
LCD
Module
LCD
Module-
001
ASSY LCD MODULE 14 .1 WXGA NON
GLARE QDI (N141V2 QD14TL01 REV 01) W/
O ANT - TM
LCD 14 .1 WXGA NON GLARE QDI N141V2
QD14TL01 REV 01
6M.TAAV5.007
LK.14109.004
19.A70V5.001
LCD
Module-
007
LCD INVERTER
LCD
Module-
006
LCD WIRE CABLE 50.A70V5.005
Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
LCD
Module-
004
Part Name and Description
LCD PANEL WITH LOGO W/O ANTENNA -
TM
Part Number
60.TAAV5.003
LCD
Module-
005
LCD BEZEL 60.A70V5.006
LCD
Module-
002, 003
LCD BRACKET SET 6K.A70V5.001
LCD
Module
LCD
Module-
001
ASSY LCD MODULE 14.1 WXGA NON
GLARE CMO (N141l 1-L03) W/O ANT-TM
LCD 14.1 WXGA NON GLARE CMO (N141l 1-
L02)
6M.TAAV5.008
LK.1410D.004
19.A70V5.001
LCD
Module-
007
LCD INVERTER
LCD
Module-
006
LCD WIRE CABLE 50.A70V5.005
LCD
Module-
004
LCD PANEL WITH LOGO W/O ANTENNA -
TM
60.TAAV5.003
Chapter 6 89
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
LCD
Module-
005
Part Name and Description
LCD BEZEL
Part Number
60.A70V5.006
LCD
Module-
002, 003
LCD BRACKET SET 6K.A70V5.001
Mainboard
Memory
Heatsink
The
System-
251
NS
NS
The
System-
007
MAINBOARD 915PM FOR VGA GLAN W/
READER PCMCIA SLOT W/O CPU
MEMORY
MAINBOARD 915GM UMA GLAN W/
READER PCMCIA SLOT W/O CPU
MEMORY
MAINBOARD 910GML UMA GLAN W/
PCMCIA SLOT W/O READER CPU MEMORY
MAINBOARD 915PM FOR VGA GLAN W/
READER PCMCIA SLOT W/O CPU
MEMORY (for TravelMate 3220)
PCMCIA SLOT
LB.TAA02.002
LB.TAA02.001
LB.TA902.001
LB.TAM06.001
22.A70V5.001
MEMORY IFX 256MB/ 533MHZ,
HYS64T32000HDL-3.7-A
MEMORY DDRII533 256MB NANYA
NT256T64UH4A0FN-37B
MEMORY SAMSUNG 512MB/ 533MHz,
M470T3354BG0-CD5
MEMORY DDRII 533 256MB HYNIX
HYMP532S64P6-C4
MEMORY IFX 512MB/ 533MHZ,
HYS64T64020HDL-3.7-A
CPU THERMAL
KN.25602.023
KN.25603.020
KN.2560B.011
KN.2560G.006
KN.51202.021
60.A70V5.007
The
System-
251
VGA THERMAL 60.A70V5.008
Pointing Device
90 Chapter 6
TravelMate 2400/3210/3220/3230 FRU List
Picture No.
Upper
Case
Assembly-
005
Part Name and Description
TOUCHPAD
Speaker
NS SPEAKER SET (R&L)
Part Number
56.A70V5.001
23.A70V5.002
Miscellaneous
NS LCD RUBBER PAD 47.A70V5.001
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
Chapter 6
NS LCD SCREW PAD 47.A70V5.002
NS LCD RUBBER
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NS
NAME PLATE - TM3210
NAME PLATE - TM3220
NAME PLATE - TM2400
RUBBER FOOT - ONE PIN
RUBBER FOOT - TWO PINS
SCREW M2*3(NL)
SCREW M2*4
SCREW M2*6
SCREW M2*6(p Ni)
SCREW M2.5*4(NL)
SCREW M2.5*6(NL)
SCREW M2.5*8(NL)
SCREW M3*4 (NL)
SCREW THERMAL SCREW ASSY
47.A70V5.003
47.TAAV5.001
40.TAMV5.001
47.TA9V5.001
47.A70V5.004
47.A70V5.005
86.A70V5.001
86.A70V5.002
86.A70V5.003
86.A70V5.004
86.A70V5.005
86.A70V5.006
86.A70V5.007
86.A70V5.008
86.A70V5.009
91
92 Chapter 6
Chapter 6 93
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 7 Features
- 10 System Block Diagram
- 11 Board Layout
- 11 Top View
- 12 Bottom View
- 13 A TravelMate tour
- 13 Front View
- 14 Closed Front View
- 14 Left View
- 16 Right View
- 17 Rear Panel
- 18 Bottom Panel
- 19 Indicators
- 20 Launch Keys
- 21 Touchpad
- 21 Touchpad Basics
- 23 Using the Keyboard
- 23 Lock Keys and embedded mumeric keypad
- 24 Windows Keys
- 25 Hot Keys
- 27 Special Key
- 28 Hardware Specifications and Configurations
- 39 BIOS Setup Utility
- 40 Navigating the BIOS Utility
- 41 Main
- 44 Advanced
- 45 Security
- 46 Boot
- 47 Exit
- 48 BIOS Flash Utility
- 51 General Information
- 51 Before You Begin
- 52 Disassembly Procedure Flowchart
- 54 Removing the Battery Pack
- 55 Removing the Wireless LAN Card/the HDD Module/the Memory/the CPU/ the ODD Module and the LCD Module
- 55 Removing the Wireless LAN Card and the HDD Module
- 55 Removing the Memory and the CPU
- 56 Removing the ODD Module and the LCD module
- 59 Disassembling the Main Unit
- 59 Separate the Main Unit Into the Upper and the Lower Case Assembly
- 59 Disassembling the Upper Case Assembly
- 60 Disassembling the Lower Case Assembly
- 62 Disassembling the LCD Module
- 63 Disassembling the External Modules
- 63 Disassembling the HDD Module
- 63 Disassembling the ODD Module
- 65 System Check Procedures
- 65 External Diskette Drive Check
- 65 External CD-ROM Drive Check
- 65 Keyboard or Auxiliary Input Device Check
- 65 Memory check
- 66 Power System Check
- 67 Touchpad check
- 68 Insyde MobilePro BIOS POST Beep Code and POST Messages
- 70 Insyde MobilePro BIOS POST Codes
- 74 Index of Symptom-to-FRU Error Message
- 78 Intermittent Problems
- 79 Undetermined Problems
- 80 Top View
- 81 Bottom View
- 83 Exploded Diagram
- 83 The System
- 84 Upper Case Assembly
- 85 Lower Case Assembly
- 86 LCD Module
- 87 HDD Module
- 87 ODD Module