Technical information | Acer 3300 Laptop User Manual

Acer TravelMate 3300/Extensa 3100 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate 3300/Extensa 3100 service guide.
Date
II
Chapter
Updates
2005/11/25
All
Revise TravelMate 3300/Extensa 3100 battery spec. on
page 25 and page 26.
2005/12/15
Chapter 1
Add “WFM” to BIOS support protocols on page 23.
Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
T
Intel® 915GM PCI Express chipset
Intel® Pentium® M processor 740/750/760/770/780 (2MB L2 cache, 1.60/1.73/1.86/2/2.13/2.26
GHz, 533 MHz FSB)
T
Intel® Celeron® M processor 360/370/380 (1MB L2 cache, 1.40/1.50/1.60 GHz, 400 MHz FSB)
T
CPU Package is uFPGA 478 Package
T
Integrated Intel® PRO/Wireless 2200BG network connection (dual-mode 802.11b/g) Wi-Fi
CERTIFIEDTM solution
Memory
T
256MB or 512MB of DDRII 400/533
T
Upgradeable to 2GB Memory by Dual channels of SODIMM
T
512KB flash ROM BIOS
Display and graphics
T
14.1” WXGA Acer Crystallbrite clolor TFT LCD: 1280x 800 resolution
T
14.1” WXGA clolor TFT LCD: 1280x 800 resolution
T
16.7 million colors
T
Intel® 915GM integrated 3D graphics, featuring Intel® Graphics Media Accelerator 900 and up to
128 MB of VRAM, supporting Microsoft® DirectX® 9.0 and dual independent display
T
MPEG-2/DVD hardware-assisted capability
T
Audio system with two built-in speakers
T
Intel® AC’97 audio support
T
Sound Blaster Pro and MS Sound compatible
T
Built-in microphone
T
S/PDIF (Sony/Philips Digital interface)
T
40/60/80/100/12060 GB ATA/100 hard disc drive
T
Optical drive options: DVD-Dual double-layer or DVD/CD-RW combo
T
5-in-1 card reader (MS/MS PRO/MMC/SD/XD)
Audio
Storage
Communication
Chapter 1
T
56Kbps ITU V92 with PTT approval; Wake-on-Ring ready
T
LAN: gigabit Ethernet; Wake-on-Ring ready
1
T
WLAN (optional):
T
T
T
Integrated Intel® PRO/Wireless 2200BG network connection (dual-band 802.11b/g) Wi-Fi
CERTIFIEDTM solution, supporting Acer SignalUpTM wireless technology, or
Integrated Acer InviLinkTM 802.11b/g Wi-Fi CERTIFIEDTM solution, supporting Acer
SignalUpTM wirelss technology
WPAN (optional): Integrated Bluetooth®
I/O Ports
T
Three USB 2.0 port
T
5-in-1 card reader (MS/MS PRO/MMC/SD/XD)
T
One Type II PC Card slot
T
IEEE 1394 port (6-pin)
T
Fast infrared (FIR) port
T
External display (VGA) port
T
Headphones/speaker/line-out port with S/PDIF support
T
Microphone-in jack
T
Line-in jack
T
Ethernet (RJ-45) port
T
Modem (RJ-11) port
T
DC-in jack (AC adapter)
T
One external monitor port
T
124-pin Acer ezDock connector
Dimensions and weight
T
330(W) x 240(D) x 23/31.3(H) mm (12.9 x 9.45 x 10.91/1.23 inches)
T
1.9Kg (4.23 lbs)
Environment
T
T
2
Temperature
T
Operating: 5o C ~ 35o C
T
Non-operating: -20o C ~ 65o C
Humidity ( non-condensing)
T
Operating: 20% ~ 80% RH
T
Non-operating: 20% ~ 80% RH
Chapter 1
Mainboard Layout
Top View
1
Fan Connector (FAN1)
6
5-in-1 Card Reader Slot (CARD1)
2
LCD Cable Connector (LCD1)
7
RTC Battery Connector (RTC1)
3
IEEE 1394 Connector (SKT1)
8
Bluetooth Module Connector (BT1)
4
USB Port (SKT2)
9
Touchpad FFC Connector (TPAD1)
5
PC Card Slot (PCH1 or U22)
10
Keyboard Connector (KB1)
Chapter 1
3
Bottom View
4
1
Giga LAN Port (JK1)
10
Main Board to IO Board Connector
(IOB1)
2
Power Jack (DCIN1)
11
HDD Connector (HDD1)
3
VGA Port (CRT1)
12
DIMM Slot (DM2)
4
ezDock Port (DOCK1)
13
DIMM Slot (DM1)
5
IO Controller-PC 87392 (U27)
14
South Bridge-Intel ICH6-M (U44)
6
Wireless LAN Card Slot (WIN1)
15
Switch (SW8)
7
Keyboard Controller (U32)
16
Cardbus/1394/Card Reader
Controller-UltraMedia PCI 7411
(U52)
8
LAN Controller-BROADCOM
BCM5788M (U31)
17
North Bridge (U34)
9
Battery Connector (BAT1)
18
CPU (U33)
19
Power Generator-IDT CV125PA
(U41)
Chapter 1
IO Board Layout
Top View
1
Microphone Connector (INTMIC1)
7
Microphone-in Port (MIC1)
2
Cover Switch Cable Connector
(LID1)
8
Line-in Port (LINT1)
3
Audio Codec-Realtek ALC655 (U1)
9
USB Port (USB1)
4
IO Board to Main Board Connector
(BTB1)
10
USB Port (USB2)
5
Speaker Set Connector (SPKR1)
11
FIR (U6)
6
Line-out Port (LOUT1)
12
RJ11 Modem Jack (JK1)
Chapter 1
5
Bottom View
1
6
Modem Board Connector (MDC 1)
2
MDC Cable Connector (RING1)
Chapter 1
System Block Diagram
CLK GEN.
CRT
Dothan
Mobile CPU
533MHz
CLE-1.5G / Dothan2.13G
(CPU on board,no socket )
4, 5
HOST BUS
Alviso-GM
6,7,8,9,10
100MHz
KI.91501.017
DMI I/F
ICH6-M
Ver. : B2, KI.80101.011
G792
PCI BUS
19
TI
PCI 7411
31
14
13
TV
(EZ4 only )
LCD
CRT
DVI-D
(EZ4 only ) 35
PCMCIA
SLOT
Support
TypeII
26
1394 6pin
Conn 27
Title
41,42
43
43
2D5V_S0(LDO)
1D5V_S0
3V_S5
5V_S5
OUTPUTS
TPS5130
SYSTEM DC/DC
INPUTS
DCBATOUT
1D05V_S0
OUTPUTS
SYSTEM DC/DC
ISL6227
INPUTS
DCBATOUT
1D8V_S3
VTT_S0(0.9V)
TPS51100DGQ
1D8V_S3
MAXIM CHARGER
16.8V
3.2A
CHG_PWR
OUTPUTS
MAX8725ETI 44
INPUTS
DCBATOUT
100mA
UP+5V
5V
CPU DC/DC
Sheet
1
OUTPUTS
VCC_CORE
0.844~1.3V
27A
47
SB
Rev
ISL6218CV-T 40
INPUTS
DCBATOUT
Myna II
Date: Monday, September 26, 2005
Size
Document Number
Custom
BLOCK DIAGRAM
<Core Design>
Project code: 91.4C201.001
PCB REVISION: 05216-SB
LVDS
RGB CRT
53 TMDS
MS/MS Pro/
xD/ MMC/SD
26
Mini-PCI
23
LPC
DEBUG
CONN.
33
RJ45 CONN
33
PM49F004T-33VC
4M BITS
BIOS ROM
23
TXFM
802.11A/B/G
(only smaller)30
5 in 1
TSP2220A
26
PWR SW
PCMCIA I/F
CH7307C
22, 23
30
INT.
KB 32
34, 35
PCIeX2 SMBUS
Touch
Pad 32
Renesas RE144B
KBC
Giga
BCM5788-M
LAN
24,25
1* Slot Cardbus
1* 1394
CardReader
NS
SIO
87392
FIR
DVI
IO Board
LPC BUS
USB
21
3 PORT
21
15,16,17,18
two USB port
on IO Board
HDD 20
MINI USB
Blue-tooth
Easy Port 4 (124 PIN)
PS2 MIC LINE IN LINE TV
OUT OUT
PRINTER
PCI-E
ACLINK
400/533MHz
400/533MHz
3
IDT CV125
Myna II
DDR II
400/533 MHz
11,12
DDR II
Int. MIC
SEARIAL
PORT
PWR SW
TPS223129
New card29
(co-lay with PCMCIA)
MODEM
MDC Card
G1421B
OP AMP
ALC655
Codec
400/533 MHz
11,12
Mic In
Line In
Line Out
INT.SPKR
RJ11 CONN
IO Board
AC RJ45-11
IN
7
Chapter 1
PATA
Outlook View
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Front View
#
8
Item
Description
1
Display screen
Also called Liquid-Crystal Display (LCD), displaying computer output.
2
Microphone
Internal microphone for sound recording.
3
Status indicators
Light-Emitting Diodes (LEDs) that turn on and off to show the status
of the computer’s functions and components
4
Touchpad
Touch-sensitive pointing device which functions like a computer
mouse.
5
Click buttons
(Left, center and right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a 4-way scroll button.
6
Palmrest
Comfortable support area for your hands when you use the computer.
7
Keyboard
For entering data into your computer.
8
Power button
Turns the computer on and off.
9
Easy-launch buttons
Buttons for launching frequently used programs.
Chapter 1
#
"Launch keys" on page 10
Item
Description
"Launch keys" on page 10
Closed front view
"Launch keys" on page 10
#
1
#
#
Icon
Icon
Icon
Item
Item
Description Description
Item
Speakers
2
Description
Left and right speakers deliver stereo audio output.
Battery indicator
#
Icon
Item
Lights up when the battery is being charged.
Description
3
Power indicator
Lights up when the computer is on.
4
Latch
Locks and releases the lid.
5
5-in-1 card reader
Accepts Memory Stick, Memory stick Pro,
MultiMedia card (MMC), Sedure Digital (SD) and
xD-Picture Card.
Note: Only one care can operate at any given time.
6
Bluetooth
communication button/
indicator
7
Wireless
communications
button/indicator
Press to enable/disable Bluetooth function. Lights
to indicate the status of Bluetooth communications.
(for TM4600 only)
Press to enable/disable Wireless function. Lights to
indicate the status of wireless LAN
communications. (manufacturing option)
Left View
Chapter 1
9
Note:
#
#
Icon
Item
#
Icon
Item
Description
Item
Description
Description
1
Kensington lock slot
Connects to a Kensington-compatible
2
Modem (RJ-11) port
Connects to a phone line.
3
Infrared port
Interfaces with infrared devices (e.g., infrared
printer and IR-aware computer).
4
#
Icon
Item
Description
Two USB 2.0 ports
Connect to USB 2.0 devices (e.g., USB mouse,
USB camera).
5
Line-in jack
Accepts audio line-in devices (e.g., audio CD
player, stereo walkman).
6
Microphone jack
Accepts input from external microphones.
Headphones/speaker/
Connects to audio line-out devices (e.g., speakers,
headphones).
7
#
Icon
Item
line-out jack
Description
NOTE: The positions of the AcerMedia indicator, eject button and emergency eject hole may differ depending
on the optical drive module installed.
#
Item
Description
Right View
10
Chapter 1
#
#
#
Icon
Item
Icon
Item
Icon
1
#
2
#
Icon
Icon
3
Description
Description
Item
Description
Note:
PC Card slot eject
button
Ejects the PC Card from the slot.
PC Card slot
Connects to one Type II CardBus PC Card.
Item
Description
Item
USB 2.0 ports
Description
Note:
Connect to Universal Serial Bus (USB) 2.0 devices
(e.g., USB mouse, USB camera).
Note:
4
IEEE 1394 port (6-pin)
Connects to IEEE 1394 devices.
5
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
6
Network jack
Connects to an Ethernet 10/100/1000-based
network (for selected models).
#
Icon
7
Item
Description
DC-in jack
Connects to an AC adapter.
Rear View
#
##
Icon
Item
Item
Icon
1
Description
Item
External display port
#
Icon
#
Icon
Item
Item
124-pin Acer ezDock
Description
Description
Connects to a display device (e.g., external
monitor, LCD projector).
Description
Description
Connects to Acer ezDock.
connector
Battery bay
Chapter 1
Houses the computer’s battery pack.
11
Bottom View
#
Item
Description
1
Battery bay
Houses the computer’s battery pack.
2
Battery lock
Locks the battery in position.
3
Cooling fan
Helps keep the computer cool.
4
Mini PCI card bay
Houses the computer’s Mimi PCI card.
5
Memory and hard disk bay
Houses the computer’s main memory and hard disk (secured with
screws).
6
Battery release latch
Release the battery for removal.
Note: Do not cover or obstruct the opening of the fan.
12
Chapter 1
Indicators
#
Item
Description
The computer has three easy-to-read status indicators on the left side of the keyboard, and four on the front
panel.
#
Item
#
Item
Description
"Launch keys" on page 10
Description
"Launch keys" on page 10
"Launch keys" on page 10
The power, battery and wireless communiction status indicators are visible even when the LCd display is
closed.
Icon
#
Icon
#
#
Icon
Icon
Item
Description
Caps Lock activity
Lights when Caps Lock is activated.
Num Lock activiy
Lights when Num Lock is activated.
Item
Media activity
Item
Item
Description
Lights when the hard disk or optical drive is active.
Description
Description
Battery
Lights up when the battery is being charged.
Power
Lights up when the computer is on.
Bluetooth
Indicates the status of Bluetooth communication.
Wireless LAN
Indicates the status of wireless LAN communication.
NOTE: 1. Charging: The light shwos amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Chapter 1
13
Easy-launch buttons
Located at the upper-right, above the keyboard are four buttons. These buttons are called easy-launch
buttons. The are: mail, Web Browser, Empowering Key <
> and one user-programmable button.
Press <
> to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email
and Internet programs, but can be reset by users.
Easy-launch button
Default application
Mail
Email application (user-programmable)
Web browser
Internet browser (user-programmable)
Acer Empowering Technology (user-programmable)
P
14
User-programmable
Chapter 1
Touchpad
The build-in touchpad is pointing device that senses movement on its surface. This means the cursor
responds as you move your finger across the surface of the touchpad. The central location on the palmrest
provides optimum comfort and support.
Touchpad Basics
Use the touchpad as follows:
T
Move your finger across the touchpad (2) to move the cursor.
T
Press the left (1) and right (4) buttons located on the edge of the touchpad to do selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button
T
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button
mimics your cursor pressing on the right scroll bar of windows applications.
Function
Left button (1)
Right button (4)
Main touchpad (2)
Execute
Quickly click twice.
Tap twice (at the
same speed as
double-clicking a
mouse button).
Select
Click one.
Tap once.
Chapter 1
Center button (3)
15
Function
Drag
Access context
menu
Scroll
16
Left button (1)
Right button (4)
Main touchpad (2)
Center button (3)
Tap twice (at the
same speed as
double-clicking a
mouse button); rest
your finger on the
touchpad on the
second tap and
drag the cursor.
Click and hold, then
use finger on the
touchpad to drag
the cursor.
Click one.
Click and hold to
move up/down/left/
right.
Chapter 1
Using the Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock Keys and embedded mumeric keypad
The keyboard has three lock keys which you can toggle on and off.
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed
are in uppercase.
Num lock
<Fn>+<F11>
When Num Lock is on, the embedded keypad is in
numeric mode. The keys function as a calculator
(complete with the arithmetic operators +, -, *, and /).
Use this mode when you need to do a lot of numeric
data entry. A better solution would be to connect an
external keypad.
Scroll lock
<Fn>+<F12>
When Scroll Lock is on, the screen moves one line up
or down when you press the up or down arrow keys
respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
Num Lock On
Num Lock Off
Number keys on embedded
keypad
Type numbers in a normal
manner.
Cursor-control keys on
embedded keypad
Hold <Shift> while using
cursor-control keys.
Hold <Fn> while using
cursor-control keys.
Main keyboard keys
Hold <Fn> while typing
letters on embedded
keypad.
Type the letters in a normal
manner.
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Chapter 1
17
Key
Icon
Windows key
Description
Pressed alone, this key has the same effect as
clicking on the Windows Start button; it launches the
Start menu. It can also be used with other keys to
provide a variety of function:
+ <Tab> Activates next taskbar button.
+ <E> Opens the My Computer window
+ <F1> Opens Help and Support.
+ <F> Opens the Find: All Files dialog box.
+ <R> Opens the Run dialog box.
+ <M> Minimizes all windows.
<Shift>+
action.
Application
key
+ <M> Undoes the minimize all windows
This key has the same effect as clicking the right
mouse button; it opens the application’s context
menu.
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like sreen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hot Key
18
Icon
Function
Description
Fn-F1
Hot key help
Displays help on hot keys.
Fn-F2
Acer eSetting
Launches the Acer eSettings in Acer eManager.
Fn-F3
Acer
ePowerManagement
Launches the Acer ePowerManagement in Acer
eManager.
Chapter 1
Hot Key
Icon
Function
Description
Fn-F4
Sleep
Puts the computer in Sleep mode.
Fn-F5
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both.
Fn-F6
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-F7
Touchpad toggle
Turns the internal touchpad on and off.
Fn-F8
Speaker toggle
Turns the speakers on and off.
Fn-w
Volume up
Increases the speaker volume.
Fn-y
Volume down
Decreases the speaker volume.
Fn-x
Brightness up
Increases the screen brightness.
Fn-z
Brightness down
Decreases the screen brightness
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.
To type:
Chapter 1
19
The Euro symbol
1.
Open a text editor or word processor.
2.
Either directly press the < > symbol at the bottom-right of the keyboard, or hold <Alt Gr> and then
press the<5> symbol at the upper-center of the keyboard.
The US dollar sign
1.
Open a text editor or word processor.
2.
Either directly press the < > key at the bottom-right of the keyboard, or hold <Shift> and then press the
<4> key at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
20
Chapter 1
Using System Utilities
Acer eManager
Innovative Acer eManagement software is designed for easy access to frequently used functions. At the press
of Acer Empowering Key, the Acer eManager user interface appears, featuring four main settings -- Acer
eSetting, Acer ePresentation, Acer ePowerManagement and Acer eRecovery.
“Launch keys” on p
Acer eSetting
Icon
“Launch
keys”
on page
20
“Launch
keys”
on page
“Launch keys” on p
Item
Description
Acer
eSetting
Acer eSetting
It is an easy way to manage the settings and security of
Acer
eSetting
your PC.
Acer eSetting
Acer ePresentation
Acer ePresentation
It takes the hassle out of making presentations.
Acer
ePresentation
Acer ePresentation
Acer ePresentation
Acer
ePowerManagement
Acer
It provides a central location from where to control all your
ePowerManagement
PC’s power schemes and maximise battery life.
Acer
ePowerManagement
Acer ePowerManagement
Acer ePowerManagement
Acer eRecovery
It backs up your files preventing data loss in the event of a
AcereRecovery
eRecovery
system crash.
Acer
Acer eRecovery
Acer eRecovery
Chapter 1
21
Launch Manager
Launch Manager allows you to set the two launch keys located above the keyboard.
You can access the Launch Manager by clicking on Start, All Programs,Start
and then Launch Manager to start
Allapplication.
Programs
the
22
Launch Manager
Chapter 1
Hardware Specifications and Configurations
Processor
Item
CPU type
Specification
®
Pentium®
M processor 740/750/760/770/780 (2MB L2 cache, 1.73/
Intel
1.87/2.0/2.13/2.26 GHz, 533 MHz FSB)
Intel® Celeron® M processor 360/370/380 (1MB L2 cache, 1.4/1.5/1.6
GHz, 400 MHz FSB)
CPU package
CPU on board no socket
CPU core voltage
Depend on DVI
CPU I/O voltage
1.2V
System Board Major Chips
Item
Controller
System core logic
Intel 915GM / ICH6-M
Super I/O controller
NS 87392, LPC interface
Audio controller
Codec ALC655
Video controller
UMA (built-in Intel® 915GM)
Hard disk drive controller
ICH6-M
Keyboard controller
Renesas RE144B
®
FIR controller
NS 87392
PCMCIA / card reader / 1394
controller
TI PCI7411
DDR-soDIMM controller
built-in Intel® 915GM
BIOS
Item
BIOS vendor
Specification
Phoenix
BIOS Version
BIOS ROM type
Flash ROM
BIOS ROM size
512KB
BIOS package
32 lead of TSSOP
Supported protocols
ACPI 2.0, PC Card 95, SMBIOS 2.3, IEEE1284-ECP/EPP, PCI 2.2, PnP
1.0a, DMI 2.0, PS/2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM
bootable, IEEE 1394, WFM 2.0 (Wired for Management)
BIOS password control
Set by setup manual
L2 Cache
Item
Cache controller
Built-in CPU
Cache size
2M (Intel® Pentium® M processor 740/750/760/770/780)
1M (Intel® Celeron® M processor 360/370/380)
1st level cache control
Always enabled
2nd level cache control
Always enabled
Cache scheme control
Always enabled
Chapter 1
23
System Memory
Item
Memory controller
Specification
®
Intel 915GM
Memory size
256MB/512MB/1GB
DIMM socket number
2
Supports maximum memory size per
slot
1024 MB
Supports maximum memory size
2GB
Supports DIMM type
DDRII SDRAM standard
Supports DIMM Speed
400/533 MHz
Supports DIMM voltage
1.8V
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications.
.
LAN Interface
Item
Specification
Supports LAN protocol
10/100/1000 Mbps Fast Ethernet connection
LAN connector type
RJ45
Wireless LAN
InviLink. 802.11b/g dual-band
LAN connector location
Right side
.
Modem/Bluetooth Interface
Item
Data modem data baud rate (bps)
Supports modem/bluetooth protocol
Specification
56K ITU
V.92 AC-Link modem with PTT approval
Wake-on-Ring ready
Modem connector type
RJ11
Modem connector location
Left side
VGA
Notice
Chipset for suitable VGA type
UMA
Intel (R) 915GM
USB Port
Item
USB compliancy level
Specification
2.0
OHCI
USB 2.0
Number of USB port
3
Location
Right Side *1
Left Side *2
Item
Audio Controller
24
Specification
AC’ 97 Codec (ALC 655)
Chapter 1
Item
Specification
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to analog converter
18 bit stereo Analog to Ditial converter
Compatibility
Microsoft PC99/2100, AC97 2.3 & WHQL/WLP2.0
Mixed sound source
CD
Sampling rate
48 KHz
Internal microphone
Yes
Internal speaker / Quantity
Yes / 2
PCMCIA Port
Item
Specification
PCMCIA controller
TI PCI 7411
Supports card type
Type II
Number of slots
One type-II
Access location
Right Side
Supports ZV (Zoomed Video) port
No
Supports 32 bit CardBus
Yes
Keyboard
Item
Specification
Keyboard controller
Renesas RE144B
Keyboard vendor & model name
Darfon
Standard keyboard with launch button embeded
Total number of keypads
Touchpad with 4-way integrated scroll button
Function keys
Four easy-launch buttons
Two front access LED buttons
Chapter 1
T
88/85 keys PS/2 and AT-compatible
keyboard
T
four inverted “T“ cursor keys
T
Hot key controls (12 function keys)
T
two Windows functions
T
Lock keys and embedded numeric keypad
T
special keys
T
international language support
T
Web Browser
T
Mail
T
Empowering key
T
One user-programmable button
T
WLAN LED button
T
Bluetooth LED button
Yes
25
Battery
Item
Specification
Vendor & model name
Sony/Sanyo
Battery Type
Li-ion
Pack capacity
53Wh
Cell voltage
7200mAh for 9-cell
Number of battery cell
9-cell
NOTE: Extensa 3100 has second battery. When the battery is running out of power, the user can replace the
battery with the second battery for prolong usage.
LCD 14.1” WXGA
Item
Specification
Vendor & model name
CMO:
QDI
Hydis
N141I1-L07 (non
glare)
QD14TL0102
HT141WX1-100
N141I1-L05 (glare)
N141C1-L02
(WXGA+)
Screen Diagonal (mm)
358.14
358.14
358.14
Active Area (mm)
303.36x189.6
303.7x189.8
303.36x189.6
1280x800
1280x800
0.237x0.237
0.237x0.237
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
303.48x189.675(for
WXGA+)
Display resolution (pixels)
1280x800 WXGA
1440x900 WXGA+
for N141C1-L02
Pixel Pitch
0.237x0.237
0.21075x0.21075
(WXGA+)
Pixel Arrangement
R.G.B. Vertical
Stripe
Display Mode (transmissive mode)
Typical White Luminance (cd/m
2)
Normally White
Normally White
Normally White
185 (typ)
185
185
also called Brightness
220 (typ for WXGA+
Luminance Uniformity
N/A
1.25
N/A
400 (Typ)
300
300
Contrast Ratio
500 (Typ)
Response Time (Optical Rise Time/Fall
Time)msec
5/11
10/15
25
Power Supply Voltage
+3.3V Typ.
+3.3V
3.3V
Typical Power Consumption (watt)
4.02 for backlight
unit only
N/A
Weight
400
440 (max)
390
Physical Size(mm)
319.5x205.5x5.2
319.5x205.5x5.2
319.5x205.5x5.2
Electrical Interface
1 channel LVDS
1 channel LVDS
1 channel LVDS
Support Color
262K colors (RGB
6-bit data driver)
262,144
262,144
Horizontal: Right/Left
45/45
40/40
45/45
Vertial: Upper/Lower
20/45
15/30
20/45
Viewing Angle (degree)
26
Chapter 1
LCD 14.1” WXGA
Item
Specification
Temperature Range( ° C)
Operating
Storage (shipping)
0 to +50
0 to +50
0 to +50
-20 to +60
-25 to +60
-20 to +60
Hard Disk Drive Interface
Item
Vendor &
Model Name
HGST Hakone
TOBHIBA Pluto
MK4025GAS
SEAGATE N2.1
ST9402112A
HGST Hakone
TOBHIBA Pluto
MK6025GAS
SEAGATE N2.2
ST960812A
HGST Hakone
TOSHIBA Pluto
MK8025GAS
SEAGATE N2.2
ST980829A
HGST Hakone
TOSHIBA Aries MK
1031GAS
SEAGATE N2.2
ST9100825A
Capacity (MB)
40000
60000
80000
100000
Bytes per
sector
512
512
512
512
Data heads
HGST Hakone
2 (Toshiba)
1 (Seagate)
HGST Hakone
4 (Toshiba)
2 (Seagate)
HGST Hakone
4 (Toshiba)
3 (Seagate)
HGST Hakone
4 (Toshiba)
4 (Seagate)
Drive Format
Disks
HGST Hakone/1/1
HGST Hakone/2/1
HGST Hakone/2/2
HGST Hakone/2/2
Spindle speed
(RPM)
4200
4200
4200
4200
Performance Specifications
Buffer size
HGST Hakone
Toshiba 8192KB
Seagate 2048KB
HGST Hakone
Toshiba 8192KB
Seagate 8192KB
HGST Hakone
Toshiba 8192KB
Seagate 8192KB
HGST Hakone
Toshiba 8192KB
Seagate 8192KB
Interface
HGST Hakone/ATA6/Parallel ATA
HGST Hakone/ATA6/Parallel ATA
HGST Hakone/ATA6/Parallel ATA
HGST Hakone/ATA6/Parallel ATA
Internal
transfer rate
(Mbytes/sec.
max.)
HGST Hakone/42.71/
56.25
HGST Hakone/38.43/
56.25
HGST Hakone/42.71/
56.25
HGST Hakone/46.62/
56.25
I/O data
transfer rate
(Mbytes/sec.
max.)
100 MB/Sec.
Ultra DMA mode 5
100 MB/Sec.
Ultra DMA mode 5
100 MB/Sec.
Ultra DMA mode 5
100 MB/Sec.
Ultra DMA mode 5
5V(DC) +/- 5%
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Allowable
voltage
5V(DC) +/- 5%
AC Adapter
Item
Vendor & model name
Specification
LITEON PA-1650-02WR (3pin, 65W)
LISHIN SLS0335A19A54LF (3pin, 65W)
Input Requirements
Maximum input current (A,
@100Vac, full load)
1.8A max@3.5A/100Vac and 240 Vac
Nominal frequency (Hz)
47 - 63
Frequency variation range (Hz)
47 - 63
Chapter 1
27
AC Adapter
Item
Specification
Nominal voltages (Vrms)
90 - 264
Inrush current
The maximum inrush current will be less than 50A and 100A when the adapter
is connected to 100Vac(60Hz) and 240Vac(50Hz) respectively.
Efficiency
High efficiency 85% minimum, at 100~240Vac AC input, full load, warm-up
condition.
Output Ratings (CV mode)
DC output voltage
Offers constant voltage 19.0V output source with 150W max output power
capacity.
Noise + Ripple
300mvp-pmax (20MHz bandwidth) for resistor load
Output current
0 A (min.)
3.5A (max.)
Output Ratings (CC mode)
DC output voltage
18.0 ~ 20.0
Constant output
7.9A
Dynamic Output Characteristics
Start-up time
3 sec. (@115 Vac and 230Vac full load)
Hold up time
5ms min. (@115 Vac input, full load)
Over Voltage Protection (OVP)
25V
Short circuit protection
Output can be shorted without damage, and auto recovery
Electrostatic discharge (ESD)
15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
4242 Vdc for 1 second-
Leakage current
60uA at 240Vac/60Hz
Regulatory Requirements
1. FCC class B requirements (USA)
2. VDE class B requirements (German)
3. VCCI classII requirements (Japan)
Power Management
ACPI Mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned off completely.
Working (G0/S0)
Individual devices such as the CPU and hard disk may be power managed in
this state.
Sleeping State (S3)
CPU Power Down
VGA Power Down
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
Super I/O Power Down
Sleeping State (S4)
Also called Hibernate state. System saves all system states and data onto the
disk prior to power off the whole system.
Dimensions and Weight
Item
28
Details
Deminsions
330(W) x 240(D) x 23/31.3(H) mm (12.9 x 9.45 x 10.91/1.23 inches)
Weight
1.9Kg (4.23 lbs)
Chapter 1
Environmental Requirements
Item
Specification
Temperature
Operating
+5°C ~ +35°C
Non-operating
-10°C ~ +60°C
Package storage
-20°C ~ 60°C
Humidity
Operating
20% ~ 85% RH
Non-operating
20% ~ 80% RH
Package storage
20% ~ 90% RH
Altitude
Operating sea level 0 to 10,000ft
Storage sea level 0 to 40,000ft
HDD Interface
Model Name
MK4025GAS ,KA100A,
40GB
Pluto MK6025GAS
60GB
Pluto MK8025GAS, 8MB,
80GB
Per drive, formatted
40.007GB
60.0116GB
80.012GB
Data Heads
2
4
4
Number of Disks
1
2
2
Data Storage Physical
Logical Configuration
Heads
16
16
16
Cylinders
16,383
16,383
16,383
User Sectors/Track at
zone 0
63
63
63
Logical Blocks (LBA)
78,140,160
117,210,240
156,301,488
100MB/sec
100MB/sec
100MB/sec
Track-to-track
2ms
2ms
2ms
Average
12ms
12ms
12ms
Maximum
22ms
22ms
22ms
Data Transfer Rate
Max transfer rate to host
Seek Time
Chapter 1
29
30
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However,
if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
The setup screen displays BIOS as follows:Navigating the BIOS Utility
Function
Item
Information
Display the system informations
Main
Allows the user to specify standard IBM PC AT
system parameters
Advanced
Provides advanced settings of the system
Security
Provides security settings of the system
Boot
Allows the user to specify the boot options
Exit
Allows the user to save CMOS setting and exit Setup
During setup,all Fn function keys and power saving functions are disabled.
There are five menu options: Main, Advanced, Security, Boot and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press p or q.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
Chapter 2
31
Information
PhoenixBIOS Setup Utility
Main
Information
Advanced
Security
Intel (R) Pentium (R) M processor 2.0GHz
CPU Type :
2000MHz
CPU Speed :
IDE1 Model Name :
ST9100825A - (PM)
IDE1 Serial Number : None
None
IDE2 Model Name :
None
IDE2 Serial Number :
System BIOS Ver:
V0.08
1232
VGA BIOS Ver
01.00
KBC Ver
xxxxxxxxxxxxxxxxxxxxxx
Serial Number
Asset Tag Number
Produce Name
N/A
TravelMate 3300/Extensa 3100
Manufacturer Name:
UUID:
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1 Help
↑ ↓
Esc Exit
←→
Parameter
32
Boot
Exit
22 Byte
32 Byte
16 Byte
16 Byte
32 Byte
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Description
CPU Type
This field displays the system CPU type.
CPU Speed
This field displays the CPU speed of the system.
IDE1 Model Name
This item will show the Model name of HDD installed on Primary IDE
master. The hard disk model name is automatically detected by the
system. If there is no hard disk present or unknown type, “None”
should be shown on this field
IDE1 Serial Number
This item will show the Serial number of HDD installed on Primary IDE
master. If no Hard disk or other devices are installed on Primary IDE
master, then it will display a blank line
IDE2 Model Name
This item will show the model name of DVD/CD-ROM drive installed on
system. The DVD/CD-ROM model name is automatically detected by
the system. If there is no DVD/CD-ROM model present or unknown
type, “None” should be shown on this field
System BIOS Version
This field reports the BIOS version of system
VGA BIOS Version
This field reports the VGA version of the system
KBC Version
This field reports the KBC version of the system.
Chapter 2
Parameter
Description
Serial Number
This item will show the Serial number of system.
Asset Tag Number
This item will show the Asset Tag number of the system.
Product Name
This field will show product name.
Manufacturer Name
This field will show manufacturer name.
UUID
This will be visible only when there is an internal LAN device present.
Chapter 2
33
Main
PhoenixBIOS Setup Utility
Information
Advanced
Main
Security
Boot
Exit
Item Specific Help
System Time:
[23:47:44]
System Date:
[11/23/2005]
System Memory:
640 KB
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system base memory size
Extended Memory:
1022 MB
Shows extended memory size
Video Memory
[128MB]
VGA memory size
Quiet Boot:
[Enabled]
Power on display:
Network boot
[Auto ]
[Enabled]
F12 Boot Menu
D2D Recovery
[Disabled]
[Enabled]
F1 Help
↑↓
Select Item
F5/F6 Change Values
F9 Setup Defaults
Esc Exit
←→
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
This menu provides you the information of the system.
Parameter
34
Description
System Time / System
Date
The hours are displayed with 24 hours format. The values set in these two fields
take effect immediately.
System Memory
This field reports the memory size of system base memory. The size is fixed to
640KB.
Extended Memory
This field reports the memory size of the extended memory in the system.
Extended Memory size = Total memory size - 1 MB
Video Memory
VGA Memory size = 128MB
Quiet Boot
Customer Logo display will be shown during POST when it is selected.
Power on display
Auto: During power on process, the system will detect if any display
device is connected on external video port. If any external display device is
connected, the power on display will be in CRT (or projector) only mode.
Otherwise it will be in LCD only mode.
Both: Simultaneously enable both the integrated LCD screen and the system’s
external video port (for an external CRT or projector).
Chapter 2
Parameter
Description
Network boot
When this is selected, Boot from LAN feature is enabled. When this is not
selected, Boot from LAN feature is then disabled.
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key
during POST. When this is not selected, device boot priority will not be
adjustable during POST.
D2D Recovery
Allow user to enable/disable the Disk-to-Disk recovery
Chapter 2
35
Advanced
The Advanced screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Infrared Port (FIR)
[Enabled]
Parallel port:
[Enabled]
Serial port
[Enabled]
Security
Boot
Exit
Item Specific Help
Configure Infrared Port
using options:
[Disable]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when controlled
by OS
F1 Help
Esc Exit
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
Description
Serial port A
36
Configure serial port A using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayed when controlled
by OS
Option
Disabled
Enabled
Auto
Chapter 2
Description
Option
Infrared Port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled
by OS
Disabled
Enabled
Auto
Parallel port
Configure serial port B using options:
[Disabled]: No configuration
[Enabled]: User configuration
[Auto]: BIOS or OS chooses configuration
(OS Controlled) Displayedd when controlled
by OS
Disabled
Enabled
Auto
Mode
Set the mode for the parallel port using
options:
Output only Bi-directional
EPP
ECP
Output only
Bi-directional
EPP
ECP
Chapter 2
37
Security
The Security screen contains parameters that help safeguard and protect your computer from
unauthorized use.
Information
PhoenixBIOS Setup Utility
Security
Boot
Main
Exit
Item Specific Help
User Password is :
Supervisor Password is :
Clear
Clear
Set User Password
Set Supervisor Password
[Enter]
[Enter]
Primary HardDisk Security
[Disabled]
Password on Boot
[Disabled]
F1
Help
Esc Exit
↑ ↓
←→
Supervisor Password
controls accesses of the
whole setup utility.
It can be used to
boot up when Password
on boot is enabled.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and
suggested parameter settings.
Parameter
Option
Supervisor Password Is
N/A
N/A
User Password Is
N/A
N/A
HDD Password Is
N/A
N/A
HDD Master ID
N/A
N/A
Set Supervisor Password
Press Enter to set the administrator
password. When set, this password
protects the BIOS Setup Utility from
unauthorized access.
[Set]: System password is set
[Clear]: System password is not set
Length -- No more than 8
characters
Characters -- 0-9, A-Z (not
case sensitive)
Set User Password
38
Description
Chapter 2
Parameter
Description
Option
Set HDD Password
When shown as [Locked], the hard drive
password currently can not be changed
or disabled.
To change or disable it, turn off the
system and enter Setup immediately after
turning it back on.
Press [Enter] to input change, or disable
hard drive password.
Enter
Password on boot
Defines whether a password is required
or not while the events defined in this
group happened. The following suboptions are all requires the Supervisor
password for changes and should be
grayed out if the user password was used
to enter setup.
Allows the user to specify whether or not
a password is required to boot.
Disabled
Enabled
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length
No more than 8 characters
Characters 0-9,A-Z (not case sensitive)
While these fields are highlighted and press “Enter”, a window similar to the following is shown:
Set SupervisorPassword
Enter New Password
[
]
Confirm New Password
[
]
If there is an old password then setup will prompt with the following window instead and a current password
will be required to be entered at first:
Set Supervisor Password
Chapter 2
Enter current password
[
]
Enter New Password
[
]
Confirm New Password
[
]
39
User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New
Password” for verification.
If the verification is OK:
The password setting is complete after user presses enter.
Setup Notice
Changes have been saved.
[ continue]
If the current password entered does not match the actual current password:
Setup Warning
Invalid password
Re-enter Password
[ continue]
If the new password and confirm new password strings do not match:
Setup Warning
Password do not match
Re-enter Password
40
Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable
devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM
in module bay and onboard LAN device.
PhoenixBIOS Setup Utility
Information
Main
Security
Boot
Exit
Item Specific Help
+Hard Drive
Floppy Devices
CD-ROM/DVD Drive
Network Boot
F1
Help
↑ ↓
←→
Esc Exit
Parameter
+Hard Drive
Floppy Devices
Keys used to view or configure
devices:
<Enter> to expands or
collapses devices with a + or <F5> and <F6> moves the
device up or down.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Description
+ and - indicate device categories. Use <Enter> to expand/
collapse.
CD-ROM/DVD Drive
Boot order is top-down using only the top device in each
category.
Netword Boot
Use <F6> and <F5> to move highlighted item up and down.
.
Chapter 2
41
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Information
Main
Security
Boot
Exit
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Disarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
42
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS
Exit Discarding
Changes
Exit utility without saving Setup data to CMOS
Load Setup Default
Load default values for all SETUP items
Discard Changes
Load previous values from CMOS for all SETUP items
Save Changes
Save Setup Data to CMOS
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screwdriver
T
Plastic flat head screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
43
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
44
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Remove the battery pack.
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery Pack
Memory
B*4
Wireless LAN
Card
A*1
HDD Module
HDD sponge
Middle Cover
HDD copper
Keyboard
LCD Module
Upper Case
Assembly
Touch Pad
Plate
C*2
D*2
E*1
F*2
G*1
H*15
I*5
Lower Case
Assembly
Touch Pad
Bluetooth
Module
Main Board
Assembly
RTC Battery
Fan
N*3
Front Cover
Speaker Set
Chapter 3
J*2
K*2
O*2
Heatsink
I/O Board
Modem
Board
Q*3
L*2
M*1
P*1
45
LCD Module
LCD Bezel
LCD Inverter
LCD
Assembly
2 hinges
Wireless
Antenna Set
V*2
LCD Brackets
W*2
R*2
S*2
T*2
U*2
X*8
LCD Cable
LCD
Screw List
46
Item
Description
A
SCW HEX NYL I#R-40/
O#4-40 L5.9
34.4C210.001
Part Number
B
SCREW MACH WAFER
M2*L4 NI
86.T39V1.002
C
SCREW M2*L9 NYLOK
86.00D38.520
D
SCRW WH MS+CBZ
M2.5+L4 BLACK
86.9A323.4R0
E
SCREW M2.5-6
86.9A323.6R0
F
SCREW M2*3 NYLON
1JMCPC-420325
86.9A352.3R0
G
SCREW
M2.5*4L(NYLOCK)BLA
CK ZN
86.9A353.4R0
H
SCREW M2.5X6
86.9A353.6R0
I
SRW M2.5*8L B/ZN
NYLOK 700
86.9A353.8R0
J
SCREW M2-3
86.9A522.3R0
K
SCRW M2*4 WAFER NI
86.9A552.4R0
Chapter 3
Removing the Battery Pack
1.
Release the battery lock.
2.
Slide the battery latch as shown then remove the battery pack.
Chapter 3
47
Removing the Wireless LAN Card/the memory and the HDD
Module and the LCD Module
Removing the Wireless LAN Card
1.
Remove the screw fastening the mini PCI cover.
2.
Detach teh mini PCI cover.
3.
Disconnect the main and the auxiliary wireless antenna.
4.
Pop out the wireless LAN card then remove it.
Removing the Memory and the HDD Module
48
1.
Remove the five screws that secure the HDD cover.
2.
Detach the HDD cover from the main unit.
3.
Pop up the memory then remove it.
4.
Lift up the HDD module then pull the HDD module backwards and remove it.
Chapter 3
.
Removing the LCD Module
1.
Open the notebook as shown.
2.
Detach the middle cover from the main unit.
3.
Remove the two screws that secure the keyboard.
4.
Turn over the keyboard as shown.
5.
Disconnect the keyboard cable then remove the keyboard.
6.
Tear off the tape fastening the wireless antenna, then pull out the antenna from the main unit.
7.
Disconnect the LCD cable from the main board.
8.
Close the LCD module and turn over the notebook, then remove two screws fastening the LCD module on
the bottom as shown.
9.
Remove one screw holding the LCD module on the rear side.
Chapter 3
49
10. Then remove two screws fastening the LCD module.
11. Detach the LCD module from the main unit carefully.
50
Chapter 3
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.
Disconnect the touchpad FFC from the main board.
2.
Disconnect the system fan cable from the main board.
3.
Remove one screw fastening the upper and the lower case assembly as shwon.
4.
Remove 15 screws fastening the upper and the lower case assembly on the bottom.
5.
Then detach the upper case assembly from the lower case assembly carefully.
Disassembling the Lower Case Assembly
1.
Disconnect the bluetooth cable from the main board then detach the bluetooth module.
2.
Disconnect the RTC battery cable from the main board then detach the RTC battery.
3.
Disconnect the speaker cable from the IO board.
4.
Disconnect the bluetooth cable from the bluetooth board.
Chapter 3
51
5.
Disconnect the microphone cablem from the IO board then detach the microphone.
6.
Disconnect the Lid switch cable from the IO board as shown.
7.
Remove the four screws fastening the mian board to the lower case.
8.
Remove two screws fastening the IO board and one screw holding the modem board.
9.
Detach the IO board from the lower case (The IO board is with modem board).
10. Remove the three screws fastening the system fan.
11. Remove the system fan from the lower case.
12. Remove the two screws that fasten the speaker set.
13. Detach the front cover from the lower case.
14. Remove the speaker set from the lower case.
15. Remove the four screws fastening the heatsink to the main board.
16. Detach the heatsink from the main board.
17. Remove the screw that fastens the modem board to the IO board.
52
Chapter 3
18. Disconnect the modem board from the IO board.
19. Disconnect the modem board cable from the modem board.
Disassembling the Upper Case Assembly
1.
Disconnect the touchpad FFC from the touchpad then remove it.
2.
Remove the five screws fastening the touchpad plate.
3.
Detach the scroll key rubber from the touchpad plate.
4.
Remove the touchpad plate.
5.
Then detach the touchpad from the upper case.
Chapter 3
53
Disassembling the LCD Module
1.
Remove the four screw caps as shown.
2.
Remove the four screws holding the LCD bezel.
3.
Then detach the LCD bezel from the LCD module.
4.
Remove the two screws fastening the inverter.
5.
Take the inverter out of the LCD panel then disconnect the LCD cable.
6.
Disconeect the LCD inverter cable on the other side then remove the inverter.
7.
Remove two screws fastening the LCD to the LCD panel.
8.
Detach the LCD from the LCD panel.
9.
Remove the two screws fastening the hinges to the LCD panel.
.
10. Remove the two hinges from the LCD panel.
11. Remove the two screws holding the wireless antenna set.
12. Then detach the wireless antenna set from the LCD panel.
54
Chapter 3
13. Remove the four screws fastening the LCD right bracket.
14. Detach the LCD right bracket from the LCD.
15. Remove the four screws fastening the LCD left bracket.
16. Detach the LCD left bracket from the LCD.
17. Tear off the tape fastening the LCD cable then disconnect the LCD cable.
Chapter 3
55
Disassembling the External Modules
Disassembling the HDD Module
56
1.
Detach the HDD sponge.
2.
Turn over the HDD module.
3.
Tear off the HDD module copper (shielding).
4.
Then detach the HDD from the HDD copper (shielding) as shown.
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1.
Obtain the failing symptoms in as much detail as possible.
2.
Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
Chapter 4
57
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if FDD Test is passed as the program runs to FDD Test.
3.
Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
58
Chapter 4
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
“Check the Power Adapter” on page 59
T
“Check the Battery Pack” on page 59
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V
Pin 2: 0V, Ground
1.
If the voltage is not correct, replace the power adapter.
2.
If the voltage is within the range, do the following:
T
Replace the System board.
T
If the problem is not corrected, see “Undetermined Problems” on page 73.
T
If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
3.
If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4.
If the operational charge does not work, see “Check the Battery Pack” on page 59.
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
Chapter 4
59
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the touchpad cables.
2.
Replace the touchpad.
3.
Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
60
Chapter 4
Power-on Self-Test Error Messages
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 73.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
61
Index of Error Messages
Error Code List
Error Codes
006
Error Messages
Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment Configuration
Error”)
010
Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070
Real Time Clock Error
071
CMOS Battery Bad
072
CMOS Checksum Error
110
System disabled.
Incorrect password is specified.
<No error code>
Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut down
system, no message will show.
<No error code>
Thermal critical High
In this situation BIOS will shut down system, not show message.
Error Message List
Error Messages
Failure Fixed Disk
FRU/Action in Sequence
Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key
see “Keyboard or Auxiliary Input Device Check” on page 58.
Keyboard error
see “Keyboard or Auxiliary Input Device Check” on page 58.
Keyboard Controller Failed
see “Keyboard or Auxiliary Input Device Check” on page 58.
Keyboard locked - Unlock key switch
Unlock external keyboard
Monitor type does not match CMOS - Run Setup
Run “Load Default Settings” in BIOS Setup Utility.
Shadow RAM Failed at offset: nnnn
BIOS ROM
System board
System RAM Failed at offset: nnnn
DIMM
System board
Extended RAM Failed at offset: nnnn
DIMM
System board
System battery is dead - Replace and run Setup
Replace RTC battery and Run BIOS Setup Utility to reconfigure
system time, then reboot system.
System CMOS checksum bad - Default
configuration used
RTC battery
System timer error
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
62
Chapter 4
Error Message List
Error Messages
Real time clock error
FRU/Action in Sequence
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
System board
Previous boot incomplete - Default configuration
used
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Memory size found by POST differed from
CMOS
Run “Load Default Settings” in BIOS Setup Utility.
DIMM
System board
Diskette drive A error
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
See “External Diskette Drive Check” on page 58.
Incorrect Drive A type - run SETUP
Check the drive is defined with the proper diskette type in BIOS
Setup Utility
System cache error - Cache disabled
System board
CPU ID:
System board
DMA Test Failed
DIMM
System board
Software NMI Failed
DIMM
System board
Fail-Safe Timer NMI Failed
DIMM
System board
Device Address Conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn
DIMM
BIOS ROM
System board
Fixed Disk n
None
Invalid System Configuration Data
BIOS ROM
System board
I/O device IRQ conflict
Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found
Enter Setup and see if fixed disk and drive A: are properly identified.
Diskette drive
Hard disk drive
System board
Chapter 4
63
Error Message List
No beep Error Messages
No beep, power-on indicator turns off and LCD is
blank.
FRU/Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 59.
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and LCD is
blank.
Power source (battery pack and power adapter). See “Power
System Check” on page 59.
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and LCD is
blank. But you can see POST on an external
CRT.
Reconnect the LCD connectors
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a
blinking cursor shown on LCD during POST.
No beep during POST but system runs correctly.
Ensure every connector is connected tightly and correctly
System board
Speaker
System board
64
Chapter 4
Phoenix BIOS Beep Codes
Code
Beeps
POST Routine Description
02h
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
22h
1-3-1-3
Test DRAM refresh
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
46h
Chapter 4
POST device initialization
2-1-2-3
Check ROM copyright notice
65
Code
POST Routine Description
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
58h
59h
66
Beeps
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
Chapter 4
Code
Beeps
POST Routine Description
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
B4h
POST done- prepare to boot operating system
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Chapter 4
67
Code
POST Routine Description
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
68
Beeps
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
LCD is too dark
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
LCD brightness cannot be adjusted
Reconnect the LCD connectors.
LCD contrast cannot be adjusted
Keyboard (if contrast and brightness function key doesn't work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen
Reconnect the LCD connector
Missing pels in characters
LCD inverter ID
Abnormal screen
LCD cable
Wrong color displayed
LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines
displayed.
LCD inverter ID
LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms
Symptom / Error
Indicator incorrectly remains off or on, but system
runs correctly
Action in Sequence
Reconnect the inverter board
Inverter board
System board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 59.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 59.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-off.
Power source (battery pack and power adapter). See “Power
System Check” on page 59.
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged
See “Check the Battery Pack” on page 59.
Battery pack
System board
Chapter 4
69
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
System board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings, then
reboot system.
DIMM
System board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
Audio driver
Speaker
System board
Internal speakers make noise or emit no sound.
Speaker
System board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation
Action in Sequence
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode and
four short beeps every minute.
See “Sleeping State (S4)” on page 28.
Press Fn+oand see if the computer enters hibernation mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode after
closing the LCD
See “Sleeping State (S4)” on page 28.
LCD cover switch
System board
The system doesn't resume from hibernation
mode.
See “Sleeping State (S4)” on page 28.
Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby mode
after opening the LCD.
See “Sleeping State (S4)” on page 28.
LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Remove battery pack and let it cool for 2 hours
Refresh battery (continue use battery until power off, then charge
battery)
Battery pack
System board
70
Chapter 4
Power Management-Related Symptoms
Symptom / Error
System hangs intermittently.
Action in Sequence
Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms
Symptom / Error
Action in Sequence
System configuration does not match the
installed devices.
Enter BIOS Setup Utility to execute “Load Default Settings”, then
reboot system.
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Reconnect hard disk/CD-ROM/diskette drives.
System board
USB does not work correctly
System board
Print problems.
Ensure the “Parallel Port” in the “Onboard Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems.
Ensure the “Serial Port” in the Devices Configuration” of BIOS Setup
Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
System board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 73.
Chapter 4
71
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
72
1.
Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 59):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
CD-ROM/Diskette drive Module
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
T
System board
T
LCD assembly
73
74
Chapter 4
Chapter 5
Jumper and Connector Locations
Mainboard Layout
Top View
1
FAN1
Fan Connector
6
CARD1
5-in-1 Card Reader Slot
2
LCD1
LCD Cable Connector
7
RTC1
RTC Battery Connector
3
SKT1
IEEE 1394 Connector
8
BT1
Bluetooth Module Connector
4
SKT2
USB Port
9
TPAD1
Touchpad FFC Connector
5
U22 or
PCH1?
?)
PC Card Slot
10
KB1
Keyboard Connector
Chapter 5
75
Bottom View
76
1
JK1
Giga LAN Port
10
IOB1
2
DCIN1
Power Jack
11
HDD1
Main Board to IO Board Connector
HDD Connector
3
CRT1
VGA Port
12
DM2
DIMM Slot
4
DOCK
1
ezDock Port
13
DM1
DIMM Slot
5
U27
IO Controller-PC 87392
14
U44
South Bridge-Intel ICH6-M
6
WIN1
Wireless LAN Card Slot
15
SW8
Switch
7
U32
Keyboard Controller
16
U52
Cardbus/1394/Card Reader ControllerUltraMedia PCI 7411
8
U31
LAN Controller-BROADCOM BCM5788M
17
U34
North Bridge
9
BAT1
Battery Connector
18
U33
CPU
19
U41
Power Generator-IDT CV125PA
Chapter 5
IO Board Layout
Top View
1
INTMIC1
Microphone Connector
7
MIC1
2
LID1
Cover Switch Cable Connector
8
LINT1
Line-in Port
3
U1
Audio Codec-Realtek ALC655
9
USB1
USB Port
4
BTB1
IO Board to Main Board Connector
10
USB2
USB Port
5
SPKR1
Speaker Set Connector
11
U6
FIR
6
LOUT1
Line-out Port
12
JK1
RJ11 Modem Jack
Chapter 5
Microphone-in Port
77
Bottom View
1
78
MDC1
Modem Board Connector
2
RING1
MDC Cable Connector
Chapter 5
Switch Settings
Please see the bottom view of the main board layout for switch location. The image bleow is switch enlarged
image.
Switch Settings
Switch
Function
SW8-1
Clear Password
SW8-2
Bootblock
SW8-3
Keyboard Matrix ID1
SW8-4
Keyboard Matrix ID2
Chapter 5
79
80
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 3300/
Extensa 3100. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise
Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information
available on your regional web or channel. For whatever reasons a part number change is made, it will not
be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office
may have a DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You
MUST use the local FRU list provided by your regional Acer office to order FRU parts for repair and service of
customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
81
Exploded Diagram
Image
Part Name
Description
Acer P/N
ADAPTER
ADAPTER 65W
LITEON PA-165002WR
ADT 65W LITEON PA1650-02WR
AP.06503.011
ADAPTER 65W LISHIN
SLS0335A19A54LF
ADT 65W LISHIN
SLS0335A19A54LF
AP.06506.003
BATTERY PACK LI+
6CELL 2.4MAH SONY
BTY PACK LI+ 6C
2.4AH SONY
BT.00604.005
BATTERY
82
Chapter 6
Image
Part Name
Description
Acer P/N
BATTERY PACK LI+
6CELL 2.4MAH SANYO
BTY PACK LI+ 6C
2.4AH SANYO
BT.00603.012
BATTERY PACK LI+
9CELL 2.4MAH SANYO
BTY PACK LI+ 9C
2.4AH SANYO
BT.00903.004
MODEM BOARD
FOXCONN
T60M845.01
MODEM MDC1.5
(AC97) T60M845.01
54.A56V1.001
TOUCHPAD BOARD
SYNAPTIC TM51-389
TOUCHPAD
SYNAPTICS TM51-389
56.TB1V1.001
WIRELESS LAN
BOARD 802.11BG
INTEL
WLAN 802.11BG
INTEL867074 LF
KI.CAX01.013
BLUETOOTH BOARD
FOXCONN BCM2045
BT MODULE
FOXCONN BCM2045
54.A74V1.003
I/O BOARD
MYNA2 I/O BD 05519SB (DIP)
55.TB1V1.001
BOARD
CABLE
83
Image
Part Name
Description
Acer P/N
MODEM CABLE
CABLE MODEM US W/
RECYCLE
50.TB1V1.002
TOUCHPAD CABLE
C.A. T/P FFC JH
MYNA2
50.TB1V1.003
POWER CODE 5A
250V 3P UK BK
CODE 5A 250V 3P UK
BK
27.03118.001
POWER CORD 2.5A
125V USA
CORD USA/W CNS
2.5A 125V 8121-
27.01518.781
BLYETOOTH CABLE
B/T CABLE HT MYNA-2
50.TB1V1.010
PCMCIA DUMMY
CARD
CARD-BUS DUMMY
CARD
42.TB1V1.003
SD MEMORY DUMMY
CARD
SD DUMMY CARD
MYNA2
42.TB1V1.004
UPPER-CASE ASSY
60.TB1V1.002
CASE/COVER/BRACKET ASSEMBLY
UPPER CASE
Note: This is
engineering sample,
and the color of the
upper case is not
correct.
84
Chapter 6
Image
Part Name
Description
Acer P/N
TOUCHPAD PLATE
ASSY T/P PLATE
MYNA2
33.TB1V1.001
LOWER CASE
ASSY L-CASE FOR
CARD BUS MYNA2
60.TB1V1.001
SPEAKER LEFT/
RIGHT
SPEAKER MYNA-2
23.TB1V1.001
MICROPHONE
MICROPHONE
MYNA2
23.TB1V1.002
COVER SWITCH
CABLE
C.A. COVER SWITCH
MYNA2
50.TB1V1.001
FRONT COVER
ASSY FRONT COVER
MYNA2
60.TB1V1.004
MIDDLE COVER
ASSY MIDDLE COVER
MYNA2
60.TB1V1.003
85
Image
Part Name
Description
Acer P/N
HDD COVER
ASSY HDD COVER
MYNA2
42.TB1V1.001
MINI PCI COVER
ASSY MINIPCI COVER
MYNA-2
42.TB1V1.002
COMBO 24X
PANASONIC UJDA770
COMBO 24X PAC/
UJDA770 MYNA EXT
KO.02406.014
COMBO 24X LITEON
SOSC-2483K
COMBO LIT/SOSC2483K LF EXT
KO.02409.014
WIRELESS ANTENNA
LEFT/RIGHT
ANTENNA CABLE
MYNA2
25.TB1V1.001
DVD-RW DRIVE 8X
LITEON SOSW-833S
DUAL
DUAL 8X LTN/SOSW833S MYNA EXT
KU.00804.020
COMBO MODULE
COMMUNICATION MODULE
DVD MODULE
86
Chapter 6
Image
Part Name
Description
Acer P/N
DVD-RW DRIVE 8X
PANASONIC UJ-840B
DUAL
DUAL PAN/UJ-840B LF
8X DVD
KU.00807.030
FAN
FAN FORCECON
MORAR
23.A74V1.001
HDD MODULE 40G
HDD MODULE 40G
TBD
HDD MYLAR W/
CUPPER
ASSY HDD CHASSIS
MYNA-2
33.TB1V1.002
HDD 40G HITACHI
HTS421240H9AT00
HDD 40GB HGST
HTS421240H9AT00
KH.04007.013
HDD 40G TOSHIBA
MK4025GAS
HDD 40GB TOSHIBA
MK4025GAS
KH.04004.005
HDD 40G SEAGATE
ST9402113A
HDD 40GB SEAGATE
ST9402113A
KH.04001.016
HDD MODULE 60G
ASSY HDD 60G
SEAGATE MYNA-2
TBD
HDD MYLAR W/
CUPPER
ASSY HDD CHASSIS
MYNA-2
33.TB1V1.002
HDD 60G HITACHI
HTS421260H9AT00
HDD 60GB HGST
HTS421260H9AT00
KH.06007.009
HDD 60G TOSHIBA
MK6025GAS
HDD 60GB TOSHIBA
MK6025GAS
KH.06004.004
HDD 60G SEAGATE
ST960812A
HDD 60GB SEAGATE
ST960812A
KH.06001.003
HDD MODULE 80G
ASSY HDD 80G HGST
MYNA-2
TBD
HDD MYLAR W/
CUPPER
ASSY HDD CHASSIS
MYNA-2
33.TB1V1.002
HDD 80G TOSHIBA
MK8025GAS
HDD 80GB TOSHIBA
MK8025GAS
KH.08004.003
HDD 80G HITACHI
HTS421280H9AT00
HDD 80GB HGST
HTS421280H9AT00
KH.08007.011
HDD 80G SEAGATE
ST980829A
HDD 80GB SEAGATE
ST980829A
KH.08001.013
HDD MODULE 100G
ASSY HDD 100G
HGST MYNA-2
TBD
FAN
HDD MODULE
87
Image
Part Name
Description
Acer P/N
HDD MYLAR W/
CUPPER
ASSY HDD CHASSIS
MYNA-2
33.TB1V1.002
HDD 100G HITACHI
HTS421210H9AT00
HDD 100GB HGST
HTS421210H9AT00
KH.10007.002
HDD 100G TOSHIBA
MK1031GAS
HDD 100GB TOSHIBA
MK1031GAS
KH.10004.001
HDD 100GB SEAGATE
ST9100825A
HDD 100GB SEAGATE
ST9100825A
KH.10001.003
KEYBOARD 88KEY
DARFON NSK-AEN1D
US-INT
KB DARFON NSKAEN1D US-INT 88K
KB.TB107.001
KEYBOARD DARFON
NSK-AEN02 CHINESE
88
KB DARFON NSKAEN02 CHINESE 88
KB.TB107.002
TM3300 KEYBOARD
SPANISH
TM3300 KEYBOARD
SPANISH
KB.TB107.003
TM3300 KEYBOARD
THAI
TM3300 KEYBOARD
THAI
KB.TB107.004
TM3300 KEYBOARD
BRAZILIAN
PROTUGESE
TM3300 KEYBOARD
BRAZILIAN
PROTUGESE
KB.TB107.005
TM3300 KEYBOARD
KOREA
TM3300 KEYBOARD
KOREA
KB.TB107.006
TM3300 KEYBOARD
UK
TM3300 KEYBOARD
UK
KB.TB107.007
TM3300 KEYBOARD
GERMAN
TM3300 KEYBOARD
GERMAN
KB.TB107.008
TM3300 KEYBOARD
ITALIAN
TM3300 KEYBOARD
ITALIAN
KB.TB107.009
TM3300 KEYBOARD
FRENCH
TM3300 KEYBOARD
FRENCH
KB.TB107.010
TM3300 KEYBOARD
SWISS/G
TM3300 KEYBOARD
SWISS/G
KB.TB107.011
TM3300 KEYBOARD
PORTUGUESE
TM3300 KEYBOARD
PORTUGUESE
KB.TB107.012
TM3300 KEYBOARD
ARABIC
TM3300 KEYBOARD
ARABIC
KB.TB107.013
TM3300 KEYBOARD
BELGIUM
TM3300 KEYBOARD
BELGIUM
KB.TB107.014
TM3300 KEYBOARD
SWEDEN
TM3300 KEYBOARD
SWEDEN
KB.TB107.015
TM3300 KEYBOARD
CZECH
TM3300 KEYBOARD
CZECH
KB.TB107.016
TM3300 KEYBOARD
HUNGAIAN
TM3300 KEYBOARD
HUNGAIAN
KB.TB107.017
TM3300 KEYBOARD
NORWAY
TM3300 KEYBOARD
NORWAY
KB.TB107.018
KEYBOARD
88
Chapter 6
Image
Part Name
Description
Acer P/N
TM3300 KEYBOARD
DANISH
TM3300 KEYBOARD
DANISH
KB.TB107.019
TM3300 KEYBOARD
TURKISH
TM3300 KEYBOARD
TURKISH
KB.TB107.020
TM3300 KEYBOARD
TURKISH F TYPE
TM3300 KEYBOARD
TURKISH F TYPE
KB.TB107.021
TM3300 KEYBOARD
CANADIAN FRENCH
TM3300 KEYBOARD
CANADIAN FRENCH
KB.TB107.022
TM3300 KEYBOARD
JAPANESE
TM3300 KEYBOARD
JAPANESE
KB.TB107.023
TM3300 KEYBOARD
GREEK
TM3300 KEYBOARD
GREEK
KB.TB107.024
TM3300 KEYBOARD
HEBREW
TM3300 KEYBOARD
HEBREW
KB.TB107.025
TM3300 KEYBOARD
RUSSIAN
TM3300 KEYBOARD
RUSSIAN
KB.TB107.026
TM3300 KEYBOARD
SLOVENIA (SLO)
TM3300 KEYBOARD
SLOVENIA (SLO)
KB.TB107.027
TM3300 KEYBOARD
CROATIA (CR )
TM3300 KEYBOARD
CROATIA (CR )
KB.TB107.28
LCD MODULE 14.1"
WXGA GLARE 400G
LCD 14" WXGA
QD14TL02-04
6M.TB1V1.001
INVERTER BOARD
DARFON
INVERTER 17" ROHS
VK.21189.401
19.TB1V1.001
LCD CABLE 14.1 "
WXGA
CABLE 14.1" WXGA HT
MYNA2
50.TB1V1.004
LCD BRACKET RIGHT
BRKT LCD 14.1" R
MYNA2
33.TB1V1.003
LCD MODULE
89
Image
90
Part Name
Description
Acer P/N
LCD BRACKET LEFT
BRKT LCD 14.1" L
MYNA2
33.TB1V1.004
LCD BEZEL 14.1"
ASSY LCD 14.1"
BEZEL MYNA-2
60.TB1V1.005
LCD BEZEL 14.1”
ASSY LCD 14.1"
BEZEL MYNA-2 (for
Extensa 3100) with
model name printing on
it
60.E31V1.001
LCD PANEL 14.1"
ASSY LCD 14.1"
PANEL MYNA-2
60.TB1V1.006
HINGE PACK LEFT/
RIGHT
HINGE PACK LEFT/
RIGHT
6K.TB1V1.001
LCD 14.1" WXGA
N141I1-L05 GLARE
400G
LCD 14" WXGA
N141I1-L05
LK.1410D.006
LCD 14.1" WXGA QDI
QD14TL02-04 400G
LCD 14" WXGA
QD14TL02-04
LK.14109.006
LCD MODULE 14.1"
WXGA GLARE 420G
LCD 14.1" WXGA
N141C1-L02
6M.TB1V1.002
INVERTER BOARD
DARFON
INVERTER 17" ROHS
VK.21189.401
19.TB1V1.001
LCD CABLE 14.1 "
WXGA
CABLE 14.1" WXGA HT
MYNA2
50.TB1V1.004
(this is different item
from TravelMate 3300)
Chapter 6
Image
Part Name
Description
Acer P/N
LCD BRACKET RIGHT
BRKT LCD 14.1" R
MYNA2
33.TB1V1.003
LCD BRACKET LEFT
BRKT LCD 14.1" L
MYNA2
33.TB1V1.004
LCD BEZEL 14.1"
ASSY LCD 14.1"
BEZEL MYNA-2
60.TB1V1.005
LCD PANEL 14.1"
ASSY LCD 14.1"
PANEL MYNA-2
60.TB1V1.006
HINGE PACK LEFT/
RIGHT
HINGE PACK LEFT/
RIGHT
6K.TB1V1.001
LCD 14.1" WXGA
N141C1-L02 GLARE
420G
LCD 14.1" WXGA
N141C1-L02
LK.1410D.008
LCD MODULE 14.1"
WXGA NONE GLARE
400G
ASSY QDI 14.1" WXGA
(N-GLAR
6M.TB1V1.003
INVERTER BOARD
DARFON
INVERTER 17" ROHS
VK.21189.401
19.TB1V1.001
LCD CABLE 14.1 "
WXGA
CABLE 14.1" WXGA HT
MYNA2
50.TB1V1.004
LCD BRACKET RIGHT
BRKT LCD 14.1" R
MYNA2
33.TB1V1.003
LCD BRACKET LEFT
BRKT LCD 14.1" L
MYNA2
33.TB1V1.004
LCD BEZEL 14.1"
ASSY LCD 14.1"
BEZEL MYNA-2
60.TB1V1.005
LCD PANEL 14.1"
ASSY LCD 14.1"
PANEL MYNA-2
60.TB1V1.006
HINGE PACK LEFT/
RIGHT
HINGE PACK LEFT/
RIGHT
6K.TB1V1.001
LCD 14.1" WXGA
N141I1-L07 NONE
GLARE 400G
LCD 14.1" WXGA
N141I1-L07
LK.1410D.007
LCD 14.1" WXGA QDI
QD14TL02-03 NONE
GLARE 400G
LCD 14" WXGA
QD14TL02-03
LK.14109.007
LCD MODULE 14.1"
WXGA NONE GLARE
420G
LCD MODULE 14.1"
WXGA
6M.TB1V1.004
INVERTER BOARD
DARFON
INVERTER 17" ROHS
VK.21189.401
19.TB1V1.001
LCD CABLE 14.1 "
WXGA
CABLE 14.1" WXGA HT
MYNA2
50.TB1V1.004
LCD BRACKET RIGHT
BRKT LCD 14.1" R
MYNA2
33.TB1V1.003
LCD BRACKET LEFT
BRKT LCD 14.1" L
MYNA2
33.TB1V1.004
LCD BEZEL 14.1"
ASSY LCD 14.1"
BEZEL MYNA-2
60.TB1V1.005
LCD PANEL 14.1"
ASSY LCD 14.1"
PANEL MYNA-2
60.TB1V1.006
HINGE PACK LEFT/
RIGHT
HINGE PACK LEFT/
RIGHT
6K.TB1V1.001
91
Image
Part Name
Description
Acer P/N
LCD 14.1" WXGA
N141C1-L03 NONE
GLARE 420G
LCD 14.1" WXGA
N141C1-L03
LK.1410D.009
LCD 14.1" WXGA QDI
QD14TL01-02 NONE
GLARE 420G
LCD 14.1" WXGA
QD14TL01-02
LK.14109.005
LCD 14.1" WXGA QDI
QD14TL01-03 NONE
GLARE 420G
LCD 14" WXGA
QDIQD14TL01-03
LK.14109.004
MAINBOARD MYNA 2
1.4G 1.73MHZ(CPU ON
BOARD) W/CPU
HEATSINK & PCMCIA
SLOT & RTC BATTERY
MB PM740 MYNA2 W/
O DIMM
LB.TB101.008
MAINBOARD MYNA 2
2.13GMHZ(CPU ON
BOARD) W/CPU
HEATSINK & PCMCIA
SLOT & RTC BATTERY
MYNA2 MB DOT-2.13G
05216SB DIP
LB.TB101.014
MAINBOARD MYNA 2
2.0GMHZ(CPU ON
BOARD) W/CPU
HEATSINK & PCMCIA
SLOT & RTC BATTERY
MYNA2 MB 2.0G
05216SB DIP
LB.TB101.012
RTC BATTERY LI
BATTERY RTC
CANARY
23.T28V1.001
CPU HEATSINK W/O
FAN
ASSY CPU HEAT SINK
MYNA2
34.TB1V1.001
PCMCIA SLOT 4PIN
CONN CARDBUS 4P
59330-00L0C
22.T28V1.001
SDIMM 256M HYNIX
HYMP532S64P6-C4
SODIMM 256M
HYMP532S64P6-C4
KN.2560G.006
SDIMM 256M
INFINEON
HYS64T32000HDL-3.7A
SODIMM256MHYS64T
32000HDL-3.7-A
KN.25602.023
MAIN BOARD
92
Chapter 6
Image
Part Name
Description
Acer P/N
SDIMM 512M
INFINEON
MHYS64T64020HDL3.7-A
SODIMM512MHYS64T
64020HDL-3.7-A
KN.51202.021
SDIMM SAMSUNG
M470T3354CZ3-CD5
Samsung
M470T3354CZ3-CD5
KN.2560B.016
SDIMM 512M NANYA
NT512T64UH8A1FN37B
SODIMM512M
NT512T64UH8A1FN37B
KN.51203.023
SDIMM 512M
SAMSUNG
M470T6554CZ3-CD5
SODIMM 512M
M470T6554CZ3-CD5
KN.5120B.015
SDIMM 512M HYNIX
HYMP564S64P6-C4
SODIMM 512M
HYMP564S64P6-C4
KN.5120G.005
LCD SCREW RUBBER
RUB LCD RUBBER
CUSHION BOLSENA
47.A46V1.002
Note: See the upper two
rubber cushion.
LCD SCREW RUBBER
RUBBER SCREW
47.TB1V1.001
Note: See the lower two
rubber
SCROLL KEY RUBBER
KNOB SCROLL KEY
MYNA2
47.TB1V1.002
Note: The picture below
shows its location. It is
put on the touchpad
plate.
LOGO PLATE FOR
BEZEL
PLT BEZEL PLATE
"ACER " LOGO
31.A46V1.001
LOGO PLATE FOR
PANEL
PLT ACER LOGO
ADHESIVE T.M.
31.T49V1.001
93
Image
94
Part Name
Description
Acer P/N
HDD SPONGE
HDD SPONGE MYNA-2
47.TB1V1.003
SCREW
SCW HEX NYL I#R-40/
O#4-40 L5.9
34.4C210.001
SCREW
SCREW MACH
WAFER M2*L4 NI
86.T39V1.002
SCREW
SCREW M2*L9 NYLOK
86.00D38.520
SCREW
SCRW WH MS+CBZ
M2.5+L4 BLACK
86.9A323.4R0
SCREW
SCREW M2.5-6
86.9A323.6R0
SCREW
SCREW M2*3 NYLON
1JMCPC-420325
86.9A352.3R0
SCREW
SCREW
M2.5*4L(NYLOCK)BLA
CK ZN
86.9A353.4R0
SCREW
SCREW M2.5X6
86.9A353.6R0
SCREW
SRW M2.5*8L B/ZN
NYLOK 700
86.9A353.8R0
SCREW
SCREW M2-3
86.9A522.3R0
SCREW
SCRW M2*4 WAFER
NI
86.9A552.4R0
Chapter 6
Download PDF

advertising