Acer 3300S Laptop User Manual

TravelMate2460&Aspire3660
Service Guide
Service guide files and updates are available
on the AIPG/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate2460 & Aspire3660 service guide.
Date
4
Chapter
Updates
Copyright
Copyright © 2005 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium 4 and Celeron are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
5
Conventions
The following conventions are used in this manual:
6
Screen messages
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
7
Chapter1 System Specifications 1
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TM 2460 Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Aspire 3660 Outlook View . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Easy-Launch Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Touchpad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . 26
Hardware Specifications and Configurations . . . . . . . . . . . . 43
Chapter2 System Utilities 54
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
55
56
58
61
62
Chapter3 Machine Disassembly and Replacement 63
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Disassembly Procedure Flowchart . . . . . . . . . . . . . . . . . . . . 65
Removing the Adapter and Battery Pack . . . . . . . . . . . . . . . 66
Removing the TV Tuner, Heatsink Module, CPU, and HDD Module 67
Removing the Memory and Wireless Card . . . . . . . . . . . . . . 69
Removing the Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . 70
Disassembling the Main Unit into Upper Case and Lower Case 71
Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . 74
Reassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . 77
HDD disassembly & Reassembly . . . . . . . . . . . . . . . . . . . . . 79
ODD disassembly & Reassembly . . . . . . . . . . . . . . . . . . . . . 80
Chapter4 Troubleshooting 81
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Self-Test (POST) Error Message . . . . . . . . . . . .
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . .
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . .
Intermittent Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
85
86
88
92
96
97
Chapter5 Jumper and Connector Locations 98
Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Bottom View . . . . . . . . . . . . . . . . . . . . 99
Chapter6 FRU (Field Replaceable Unit) List 100
Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Part List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
1
Chapter 1
System Specifications
Features
This computer was designed with the user in mind. Here are just a few of its many features:
Performance
T
Intel® Pentium® M YonahProcessor dual core at 1.66~2.16 GHz
T
Intel® Pentium® M Yonah Processor single core at 1.66~1.83 GHz
T
Intel® Celeron® M Yonah Processosr at 1.66~1.83 GHz
T
North Bridge:
Chipset
T
T
ATI RC410ME
South Bridge:
T
SB460
Memory
T
DDRII 533/667 SDRAM
T
Two DDR2 SODIMM slots
T
Upgradeable to 2GB Memory
T
15.4” TFT WXGA
T
15” TFT XGA
Display
Graphics
T
UMA
T
Discrete
T
ATI MOBILITYTM RADEON® M52PG, X1300(M52P)
VRAM
T
UMA
T
T
Share 64MB, up to 256MB
Discrete
T
M52P:128MB, up to 512MB of HyperMemoryTM
Audio
Chapter 1
T
Realtek ALC883 Audio Codec
T
HD(High Definition) Audio
T
SNR > 85
T
Internal Microphone
T
Two speakers, at lease 1W/2.5cc for each
1
T
Enable VoIP function
T
PATA(SATA ready)
T
9.5mm height, 2.5” HDD
T
Easily removable
T
60/80/100/120GB
T
4200 or 5400 rpm
T
PCI Bus Master Enhanced IDE
T
Support Ultra DMA100, S.M.A.R.T
Storage
Communication
T
56Kbps V.90/V.92 AC-Link modem card (MDC1.5)
T
10/100Mbps Fast Ethernet on board
T
WLAN 802.11b/g or 802.11 a/b/g dual-band tri-mode Wireless with Mini-PCI interface
T
Mini USB bluetooth module and built-in 1 antenna
T
Built-in 2 Antenna (which has to be placed on the top of LCD on the sides of LCD latch)
I/O Ports
T
3 external USB 2.0 ports
T
Ethernet (RJ-45) port
T
Modem (RJ-11) port
T
One External display (VGA) port(15-pin)
T
One Microphones-in
T
One Line-in jack
T
One Headphones/Line-out jack with SPDIF support
T
One DC-in jack for AC adaptor
T
1 PCMCIA
T
5-in-1 card reader
T
8-cell of 18650 Li-ion battery pack, (2400mAh)
T
4-cell of 18650 Li-lon battery pack, (2000mAh)
T
6-cell of 18650 Li-lon battery pack, (2000mAh)
T
3-pin 90W AC adaptor
Battery
2
Chapter 1
Block Diagram
ZB3
X'TAL
14.31818MHz
VGA option
Yonah/Yonah Celeron-M
Clock generator
ICS951413CGLFT
V
+1.0V/+1.2V
VGA Power
MAX1993
INTEL Mobile_479 CPU
SOCKET_M
Page:5
Page:30
Page:3, 4
VGA_CORE
VGA Memory
128MB/256MB
(Channel-B)
Page:19
HOST BUS 533/667MHZ
DDR-II SODIMM1
DDR-II 533/667MHz
Page: 10
NB
ATi RC410ME
533MHz/667MHz
PCI-E 16X
Page:
Page: 10
RGB
CRT
Page: 20
LVDS
LVDS
Page: 15, 16,
17, 18, 19
707-Pins FCBGA Package
DDR-II SODIMM2
VGA
ATI M52-P(M54-P)
Page: 20
6 , 7, 8, 9
UMA(option)
Manufacturing Option
2X PCIE
2X PCIE
MINI-Card
Wireless LAN
Page: 22
SATA HDD
Page: 21
PATA HDD
2X PCIE
SATA
USB7
64QFN-Pins Package
SB
ATA 66/100
MARVEL
88E8038
RTC
Page: 21
Page: 23
Page: 11
ATi SB460
BOTHHAND
TRANSFORMER
NS0013
RJ45
Page: 23
Page: 23
549-Pins BGA Package
PCI BUS 33MHZ
IDE-ODD
TI PCI7412
Cardbus controller
Page: 21
Azalia
Page: 11, 12, 13, 14
MIC-IN
Page: 26
LINE-IN
USB 2.0
AD17
REQ3# / GNT3#
INTE#, INTH#,
INTG#(share)
AUDIO CODEC
REALTEK- ALC883
X'TAL
32.768KHz
48-pins Package
Page: 26
Page: 26
Audio AMP
MAX9755
Page: 27
MODEM
LPC 33MHZ
Page: 24,25
KBC
NS PC97551
BIOS
176-Pins Package
Page: 28
Page: 28
Page: 26
RJ11
Touchpad
Page: 27
Page: 23
Page: 26
Keyboard
Page: 29
Audio DJ
Bluetooth
USB
interface
Page: 27
FAN
Page: 29
Page: 24
5 IN1 CARD
READER
Page: 25
MINI-PCI
Wireless LAN
Page:22
SPEAKER
PCMCIA
SLOT
USB6
AD20
REQ2# / GNT2#
INTF#,
INTG#(share)
Page: 22
SYSTEM
USB PORT*3
Page: 22
USB0,2,4
Chapter 1
3
TM 2460 Outlook View
Just for Starters...
A general introduction of ports allow you to connect peripheral devices, as you would with a desktop PC.
Open View
#
#
4
Item
Item
Description
Description
1
Built-in camera
0.31 megapixel web camera for video communication(for
selected models)
2
Display screen
Also called Liquid-Crystal Display (LCD), displaying computer
output.
3
Microphone
Internal microphone for sound recording.
4
Keyboard
Inputs data into your computer.
5
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
6
Click buttons
(Left, center and
right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a 4-way scroll button.
7
Palmrest
Comfortable support area for your hands when you use the
computer.
8
Power button
Turns the computer on and off.
9
Easy-launch buttons Buttons for launching frequently used programs.
10
Status indicators
Light-Emitting Diodes (LEDs) that turn on and off to show the
status of the computer’s functions and components.
Chapter 1
#
Icon
Item
Description
"Easy-launch buttons" on page 25
Front#ViewItem
#
Icon
# #
Icon
Icon
#
Item
#
1
Icon
N/A
#
Description
Description
Item
Item
Item
Description
Description
"Launch keys"
on page 10
Description
Icon
2
Item
Item
Description
Description
Speakers
Left and right speakers deliver stereo audio output.
Power indicator
Indicates the computer’s power status.
"Launch keys" on page 10
3
Battery indicator Indicates the computer’s battery status.
4
Line-in jack
5
#
6
Mic-in jack
Item
Icon
##
Icon
Icon
#
Icon
Accepts audio line-in devices (e.g., audio CD player,
stereo walkman).
Accepts inputs from external microphones.
Description
Item
ItemHeadphones/
Item
7
Description
Description
Connects
to audio line-out devices(e.g., speakers,
speaker/line-out headphones)
Description
jack with
S/PDIF support
5-in-1 card
reader
Accepts Memory Stick(MS), Memory Stick PRO(MS
PRO), MultiMediaCard(MMC), Secure Digital (SD) and
xD-Picture Card(xD)
NOTE: Only one card can operate at any given time.
Note:
Note:
8
Bluetooth
communication
button/indicator
9
Wireless
Press to enable/disable Wireless function. Lights to
communications indicate the status of wireless LAN communications.
button/indicator (manufacturing option)
10
N/A
Latch
Press to enable/disable Bluetooth function. Lights to
indicate the status of Bluetooth communications.
Locks and releases the lid.
Chapter 1
5
#
Icon
Item
Description
Note:
Left View
#
#
Item
Description
Icon
Item
Description
1
N/A
Optical drive
Internal optical drive; accepts CDs or DVDs
2
N/A
Optical disk access
indicator
Lights up when the optical drive is active.
3
N/A
Optical drive eject button
Ejects the optical disk from the drive.
4
N/A
Emergency eject hole
Ejects the optical drive tray when the computer is
turned off.
Right View
#
Item
#
#
Icon
Description
Item
Icon
Description
Item
Description
1
PC Card slot eject
button
Ejects the PC Card from the slot.
2
PC Card slot
Connects to one Type II CardBus PC Card.
##
Item
Icon
Description
Description
Item
3
Two USB 2.0 ports
Connect to Universal Serial Bus (USB) 2.0 devices
(e.g., USB mouse, USB camera).
4
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
5
External
display(VGA) port
Connects to a display device(e.g., external monitor,
LCD projector)
#
6
#
Icon
Icon
Item
Item
Description
Description
Chapter 1
#
Icon
Item
Description
Rear View
Note:
#
#
1
Icon
Item
Icon
#
#
Icon
Icon
Item
Description
Item DC-in Jack
Description
Connects to an AC adapter.
Item
2
3
Description
Description
USB2.0 ports
#
Icon
##
Icon
Connect to USB 2.0 devices(e.g., USB mouse, USB
camera)
Connects to an Ethernet 10/100/1000 based network.
Item Ethernet(RJ-45) Description
port
Item
Item
Description
Description
4
Modem(RJ-11) port
Connects to a phone line.
5
Battery
Powers the computer
6
Kensington lock slot Connects to a Kensington-compatible computer security
lock.
#
Icon
Item
Description
#
Item
Description
#
Item
Description
Note
Note
Chapter 1
7
Bottom View
#
#
8
Item
Description
Item
Description
1
Battery release latch
Unlatches
the battery to remove the battery pack.
Note
2
Cooling fan
Helps keep the computer cool.
NOTE: Do not cover or obstruct the opening of the fan.
3
Memory compartment
Houses the computer's main memory
4
Hard disk bay
Houses the computer’s main memory
5
Battery lock
Locks the battery in position.
6
Battery bay
Houses the computer’s battery pack.
Chapter 1
Aspire 3660 Outlook View
Just for Starters...
Open View
#
#
Chapter 1
Item
Item
Description
Description
1
Built-in camera
1.3 megapixel web camera for video communication(for select
models)
2
Display screen
Also called Liquid-Crystal Display (LCD), displaying computer
output.
3
Microphone
Internal microphone for sound recording.
4
Keyboard
Inputs data into your computer.
5
Touchpad
Touch-sensitive pointing device which functions like a
computer mouse.
6
Click buttons
(Left, center and
right)
The left and right buttons function like the left and right mouse
buttons; the center button serves as a 4-way scroll button.
7
Palmrest
Comfortable support area for your hands when you use the
computer.
8
Power button
Turns the computer on and off.
9
Easy-launch buttons Buttons for launching frequently used programs.
9
"Launch keys" on page 10
"Launch keys" on page 10
#
Status indicators
Icon
Item
10
Description
Light-Emitting Diodes (LEDs) that turn on and off to show the
status of the computer’s functions and components.
"Easy-launch buttons" on page 23
Front View
#
Icon
# #
Icon
Icon
#
Item
#
#
1
Icon
Item
Description
Item
Item
Description
Description
Description
Item
Icon
Description
Item
N/A
2
Description
Speakers
Left and right speakers deliver stereo audio output.
Power indicator
Indicates the computer’s power status.
"Launch keys" on page 10
3
Battery indicator Indicates the computer’s battery status.
4
Line-in jack
Accepts audio line-in devices (e.g., audio CD player,
stereo walkman).
5
Mic-in jack
Accepts inputs from external microphones.
6
##
Icon
Icon
#
7
Icon
Item
ItemHeadphones/
Item
Description
Description
Connects
to audio line-out devices(e.g., speakers,
speaker/line-out headphones)
Description
jack with
S/PDIF support
5-in-1 card
reader
Accepts Memory Stick(MS), Memory Stick PRO(MS
PRO), MultiMediaCard(MMC), Secure Digital (SD) and
xD-Picture Card(xD)
NOTE: Only one card can operate at any given time.
Note:
8
10
Bluetooth
communication
button/indicator
Note:
Press to enable/disable Bluetooth function. Lights to
indicate the status of Bluetooth communications.
Chapter 1
Note:
9
Wireless
Press to enable/disable Wireless function. Lights to
communications indicate the status of wireless LAN communications.
button/indicator (manufacturing option)
10
N/A
Latch
Locks and releases the lid.
Left View
#
#
Item
Description
Icon
Item
Description
1
N/A
Optical drive
Internal optical drive; accepts CDs or DVDs
2
N/A
Optical disk access
indicator
Lights up when the optical drive is active.
3
N/A
Optical drive eject button
Ejects the optical disk from the drive.
4
N/A
Emergency eject hole
Ejects the optical drive tray when the computer is
turned off.
Right View
#
Item
#
#
1
Icon
Description
Item
Icon
N/A
2
#
3
Chapter 1
Icon
Description
Item
Item
Description
PC Card slot eject
button
Ejects the PC Card from the slot.
PC Card slot
Connects to one Type II CardBus PC Card.
Description
Two USB 2.0 ports
Connect to Universal Serial Bus (USB) 2.0 devices
(e.g., USB mouse, USB camera).
11
#
Item
Description
Note:
#
4
Icon
Item
N/A
5
#
Icon
Description
Ventilation slots
Enable the computer to stay cool, even after
prolonged use.
External
display(VGA) port
Connects to a display device(e.g., external monitor,
LCD projector)
Item
Description
Rear View
Note:
#
#
1
#
#
Icon
Icon
Icon
Icon
Item
Item DC-in Jack
Description
Description
Connects to an AC adapter.
Item
2
3
Description
Item
Description
USB2.0 ports
#
Icon
##
Icon
Connect to USB 2.0 devices(e.g., USB mouse, USB
camera)
Connects to an Ethernet 10/100/1000 based network.
Item Ethernet(RJ-45) Description
port
Item
Item
Description
Description
4
Modem(RJ-11) port
Connects to a phone line.
5
Battery
Powers the computer
6
Kensington lock slot Connects to a Kensington-compatible computer security
lock.
#
Icon
Item
Description
12
Chapter 1
#
Item
Description
#
Item
Description
Note
Bottom View
#
#
Chapter 1
Item
Description
Item
Description
1
Battery release latch
Unlatches the battery to remove the battery pack.
2
Cooling fan
Helps
keep the computer cool.
Note
NOTE: Do not cover or obstruct the opening of the fan.
3
Memory compartment
Houses the computer's main memory
4
Hard disk bay
Houses the computer’s main memory(secured with screws)
5
Battery lock
Locks the battery in position.
6
Battery bay
Houses the computer’s battery pack.
13
Indicators
Your computer provides an array of three indicators located above the keyboard, in addition to four
indicators positioned at the front panel. These indicators show the status of the computer
#
Item
Description
and its component.
"Launch keys" on page 10
#
Item
Description
"Launch keys" on page 10
#
Item
Description
The power, battery and wireless communication status indicators are visible even when the LCD display is
Icon
Function
Description
closed.
Icon
Icon
#
Item
Item
Description
Description
"Launch
pageup10when Caps Lock is activated.
Caps Lock
activitykeys" onLights
#
#
14
Icon
Icon
Item Num Lock activity
Description
Lights upwhen Num Lock is activated.
HDD
Indicate when the hard disk drive is active.
Bluetooth
Indicates the status of Bluetooth communication.
Item
Description
Wireless LAN
Indicates the status of wireless LAN communication.
Power
Indicates the status of computer’s power status.
Chapter 1
#
Icon
Item
Icon
Description
Item
Battery
Description
Indicates the computer’s battery status.
NOTE: The lights shows amber when the battery
is charging.
NOTE: The lights showns green when in AC
mode.
Chapter 1
15
1. Charging:
2. Fully charged:
1. Charging:
2. Fully charged:
Easy-Launch Buttons
Located at the upper-right, above the keyboard are four easy-launch buttons. They are User-Programmable
Button, Mail, Web Browser, Acer Empowering Key from left to right.
"Acer
"
Empowering Technology" on page 1
Aspire 3660
TravelMate 2460
"Launch Manager" on page 43
"Launch Manag
ger" on p
pag
ge 43
Easy-launch button
Easy-launch button
16
Default application
Item
Default application
Default Application
P
User programmable
e
Acer Empowering Technology(User-programmable)
Web Browser
Internet browser(User -programmable)
Mail
Email application(User-programmable)
Chapter 1
Touchpad
The build-in touchpad is a pointing device that senses movement on its surface.
This means the cursor responds as you move your finger across the surface of the touchpad.
The touchpad is located in the middle of the palm rest area, providing maximum comfort and efficiency.
Touchpad Basics
TravelMate 2460
Aspire 3660
T
Move your finger across the touchpad to move the cursor.
T
Press the left (1) and right (4) buttons located beneath the touchpad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad is the same as clicking the left button
T
Use the 4-way scroll (3) button to scroll up or down and move left or right a page. This button
mimics your cursor pressing on the right scroll bar of windows applications.
Function
Left Button(1)
Righ Button(4)
Main touchpad(2)
Execute
Click twice quickly
Tap twice (at the
same speed as
double-clicking the
mouse button)
Select
Click once
Tap once
Drag
Click and hold.
Then slide your
finger across the
touchpad to drag
the cursor over the
selection.
Tap twice quickly; rest
your finger on the
touchpad on the
second tap and drag
the cursor.
Access
context
menu
Scroll
Center button(3)
Click once
CLick and hold to
move up/down/left/
right
NOTE: When using the touchpad, keep it-and your fingers-dry and clean. The touchpad is sensitive to finger
movement; hence, the lighter the touch, the better the response. Tapping harder will not increase the
touchpad’s responsiveness.
Chapter 1
17
Using the Keyboard
The full-sized keyboard includes an embedded numeric keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock keys and Embedded Numeric Keypad
The keyboard has four lock keys which you can toggle on and off.
TravelMate 2460
Lock key
DescriptionAspire 3660
<Fn> + <F11>
<Fn> + <F12>
Lockfeatures
key
Description
The computer
three
lock keys, each with its own status indicator light.
Lock Key
Caps Lock
Description
<Fn> Caps
+ <F11>
When
Lock is on, all alphabetic characters are typed in
Desired access
Num
on
Numkey
Lockon
off
uppercase.
Toggle on and
offLock
by pressing
the Caps Lock
the
left side of the keyboard.
Num lock
<Fn+F11>
When Num Lock is on, the embedded keyboard is in numeric mode.
The
keys function as a calculator(complete
with the arithmetic
<Shift>
<Fn>
<Fn> + <F12>
operators+,-,*, and /). Use this mode when you need to do a lot of
numeric data entry. A better solution
would be to connect and
<Fn>
external keypad.
Scroll lock
<Fn+F12>
When Scroll Lock is on, the screen moves one line up or down when
you press the up or down arrow keys respectively. Scroll Lock does
not work with some applications.
The embedded numeric
keypad functions
like a desktop numeric keypad.
It is indicated by small characters
Desired access
Num Lock on
Num Lock off
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
<Shift>
Desired access
Numer keys on
embedded keypad
18
Num Lock on
<Fn>
Num Lock off
<Fn>
Type numbers in a normal manner
Chapter 1
Desired access
Num Lock on
Cursor-control keys Hold <Shift> while using cursoron embedded
control keys.
keypad
Main keyboard
keys
Hold <Fn> while typing letters on
embedded keypad.
Num Lock off
Hold <Fn> while using cursor-control
keys.
Type the letters in a normal manner.
Windows Keys
The keyboard has two keys that perform Windows-specific functoins.
Windows logo key
Pressed alone, this key has the same effect as clicking on the
Windows Start button; it launches the Start menu. It can also be
used with other keys to provide a variety of functions:
+ Tab (Activates the next Taskbar button)
+ E (Opens the My Computer window)
+ F1 (opens Help and Support)
+ Tab
++F
E (opens the Find: All Files dialog box)
+ F1
+F
+ M (minimizes all windows)
+M
+
+logo
M key + M (undoes the minimize all windows
j + Shift
Windows
action)
+M
+R
+ R (opens the Run dialog box)
Application key
This key has the same effect as clicking the right mouse button; it
opens the application’s context menu.
Hotkeys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility. To activate hotkeys, press and hold the <Fn> key before
pressing the other key in the hotkey combination.
Chapter 1
19
<
> + <Tab>:
<
> + <E>:
<
> + <F1>:
<
> + <F>:
<
+ <R>:
<Fn>
>TravelMate
+ <M>:
2460
<Shift> + <
> + <M>:
<Fn>Fn
Fn
Fn
Aspire 3660
Fn
Hot Key
Fn+F1
Icon
Fn-F1
Fn-F1
Fn-F1
Fn-F1
Fn-F2
Fn-F2
Fn+F2 Fn-F2
Item
Hot key help
This key will cause a help
message to appear on the display
device that describes the definition
and functionality of the unit hot
keys.
Acer eSettings
Launches the Acer eSetting in
Acer Empowering Technology.
See “Acer Empowering
Technology”
Acer ePower
Management
Launches the Acer ePower
Management in Acer Empowering
Technology. See “Acer
Empowering Technology”
Sleep
Puts the computer in Sleep mode
Display toggle
Switches display output between
the display screen, external
monitor(if connected)and both .
Screen blank
Turns the display screen backlight
off to save power. Press any key
to return
Fn-F2
Fn-F3
Fn+F3 Fn-F3
Fn-F3
Fn-F3
Fn+F4
Fn+F5
Fn-F4
Fn-F4
Fn-F5
Fn-F4
Fn-F4
Fn-F5
Fn+F6
Fn-F6
Description
Fn-F6
Fn-F7
20
Fn-F7
Fn-F8
Fn-F8
FnFn-
Chapter 1
Fn-F5
Fn-F5
Fn-F5
Fn-F5
Fn-F5
Fn-F5
Fn-F6
Hot Key Fn-F6
Fn+F7
Icon
Item
Fn-F6
Fn-F6
Fn-F7
Fn-F6
Description
Touchpad toggle
Turns the internal touchpad on
and off
Speaker toggle
Turns the speakers on and off
Volume up
Increases the sound volume
Volume down
Decreases the sound volume
Brightness up
Increases the screen brightness
Fn-F7
Fn+F8
Fn-F7
Fn-F6
Fn-F8
Fn-F7
Fn-F7
Fn-F8
Fn-F8
Fn-F8
Fn-F7
FnFn-F8
Fn+w Fn-
FnFn-F8
FnFnFn-
Fn+y FnFnFnFn-
FnFn-
Fn+x
FnFnFn-
FnFnFnFnFnFnFnFnFn+z FnBrightness down
Decrease the screen brightness
Home
FnFnFnFnHome
Home
Home
FnFnHome
Pg Up
FnFnFnHome
FnPg
Up
Pg
Up
FnPg
FnPg Up
Dn
Fn-Up
FnPg
Special Keys FnFnPg
Up
PgDn
Dn
Pg
PgEuro
Dn symbol and the US dollar sign at the upper-center and/or bottom-right of your
You can locate theFnFn-End
Fn-Dn
keyboard.
Pg
Pg
Dn
Fn-End
Fn-End
TravelMate 2460
Fn-End
Fn-End
Fn-End
Aspire 3660
Alt Gr>
<5>
Note
www.microsoft.com/typography/faq/faq12.htm
<Shift>
Chapter 1
<4>
Alt Gr>
<5>
Note:
Note
www.microsoft.com/typo graphy/faq/faq12.htm
21
The Euro Symbol
1.
Open a text editor or word processor.
2.
Either press <
Alt Gr>
at the bottom-right of the keyboard, or hold <Alt
Gr> and then press the <5> key at
> ><5>
Alt Gr>
th <5>
the upper-center of the keyboard.
Note
NOTE: Some fonts and software
do not support the
Euro symbol. Please refer to www.microsoft.com/
www.microsoft.com/typo
graphy/faq/faq12.htm
Note
typography/faq/faq12.htm
for more information.
www.microsoft.com/typo graphy/faq/faq12.htm
The US Dollar Sign
1.
Open a text editor or word processor.
2.
Either press <
> at the bottom-right of the keyboard, or hold
<Shift> and then press the <4> key at
<Shift>
th
<4>
<4>
the upper-center of the keyboard.
<Shift>
NOTE: This function varies according to the language settings.
Note:
Note:
22
Chapter 1
Note:
Using the System Utilities
Acer GridVista(dual-display compatible)
To enable the dual monitor
feature of your notebook, first ensure that the second monitor is connected, then,
Note:
select Start, Control Panel, Display and click on Settings.
the secondary
monitor (2) icon in the
StartSelect
Control
Panel Display
displaySettings
box and then click the check box Extend my Windows
desktop
onto
this
monitor.
Finally, click Apply to
(2)
confirm the new settings and click OK to complete the process.
Extend my windows desktop onto this monitor
OK
Apply
Note:
Start Control Panel Display
(2)
Extend my Windows desk top onto this monitor
OK
Settings
Apply
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access this function, please go to Start, All Programs and click on Acer GridVista.
You may choose any
one of
thePrograms
four display settings indicated
below:
Start
All
Acer
GridVista
Start All Programs
1
2
1
Acer GridVista
2
1
3
2
3
1
3
2
4
Double(vertical), Triple(primary at left), Triple(primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is imple to set up:
1.
Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2.
Drag and drop each window into the appropriate grid.
3.
Enjoy the convenience of a well-organized desktop.
Chapter 1
23
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Note:
Note:
Launch Manager
"Easy-launch
buttons"
on page
Launch Manager allows you to set
the four easy-launch
buttons
located24
above rhw keyboard. You can access
"Easy-launch
on page and
22 then Launch Manager to start the application.
the Launch Manager by clicking
on Start, buttons"
All Programs,
Start All Programs
Launch Manager
Norton AntiVirus
Norton AntiVirus is an anti-virus software that finds and repairs infected files, and protects against viruses to
keep your computer data safe and secure.
How do I check for viruses?
A Full System Scan scans all files on your computer. To perform a system scan:
1.
24
Start Norton AntiVirus.
Chapter 1
Double click on the Norton AntiVirus icon on the desktop or click on the Start menu in the Windows
taskbar, highlight Programs, and select Norton AntiVirus.
2.
In the Norton AntiVirus main window, click Scan for Viruses.
3.
In the Scan for Viruses panel, click Scan My Computer.
4.
Under Actions, click Scan.
5.
When the scan is complete, a scan summary appears. Click Finished.
You can schedule customized virus scans that run unattended on specific dates and times or at periodic
intervals. If you are using the computer when the scheduled scan begins, it runs in the background so that you
do not have to stop working.
For more information refer to the Norton Antivirus Help menu.
Chapter 1
25
Acer Empowering Technology
Acer’s innovative Empowering Technology makes it easy for you to access frequently used functions and
manage your new Acer notebook. It features the following handy utilities:
T
T
T
T
T
T
T
T
Acer eNet Management hooks up to location-based networks intelligently.
Acer ePower Management extends battery power via versatile usage profiles.
Acer ePresentation Management connects to a projector and adjusts display settings conveniently.
Acer eDataSecurity Management protects data with passwords and advanced encryption algorithms.
Acer eLock Management limits access to external storage media.
Acer eRecovery Management backs up and recovers data flexibly, reliably and completely.
Acer eSettings Management accesses system information and adjusts settings easily.
Acer ePerformance Management improves system performance by optimizing disk space, memory and
registry settings.
For more information, press the <
> key to launch the Empowering Technology menu, then click on the
appropriate utility and select the Help or Tutorial function.
Empowering Technology Password
Before using Acer eLock Management and Acer eRecovery Management, you must initalize the Empowering
Technology password. Right-click on the Empowering Technology toolbard and select “Password Setup” to do
so. If you do not initialize the Empowering Technology password, you will be prompted to do so when running
Acer eLock Management or Acer eRecovery Management for the first time.
Acer eNet Management
Acer eNet Management helps you to quickly and easily connect to both wired and wireless networks in a
variety of locations. To access this utility, either click on the “Acer eNet Management” icon on your netebook,
or start the program from the Start menu. You also have the option to set Acer eNet Management to start
automatically when you boot up your PC.
Acer eNet Management automatically detects the best settings for a new location, while offering you the
freedom to manually adjust the settings to match your needs.
26
Chapter 1
Acer eNet Management can save network settings for a location to a profile, and automatically switch to the
appropriate profile when you move from one location to another. Settings stored include network connection
settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings.
Security and safety concerns mean that Acer eNet Management does not store username and password
information.
Chapter 1
27
Acer ePower Management
Acer ePower Management features a straightforward user interface. To launch it, select Acer ePower
Management from the Empowering Technology interface.
AC Mode (Adapter mode)
The default setting is “Maximum Performance.” You can adjust CPU speed, LCD brightness and other
settings, or click on buttons to turn the following functions on/off: Wireless LAN, Bluetooth, CardBus, FireWire
(1394), Wired LAN and Optical Device if supported.
DC Mode (Battery mode)
There are four pre-defined profiles - Entertainment, Presentation, Word Processing, and Battery Life. You can
also define up to three of your own.
To create new power profile
28
1.
Change power settings as desired.
2.
Click “Save as...” to save to a new power profile.
3.
Name the newly created profile.
4.
Select whether this profile is for Adapter or Battery mode, then click OK.
Chapter 1
5.
The new profile will appear in the profile list.
Battery status
For real-time battery life estimates based on current usage, referto the panel on the lower left-hand side of the
window.
For additional options, click “Settings” to:
T
T
T
T
Set alarms.
Re-load factory defaults.
Select what actions will be taken when the cover is closed or the power button is pressed.
View information about Acer ePower Management.
Chapter 1
29
Acer ePresentation Management
Acer ePresentation Management lets you project your computer’s display to an external device or project
using the hot key: Fn + F5. If auto-detection hardware is implemented in the system, your system display will
be automatically switched out when an external display is connected to the system.
30
Chapter 1
Acer eDataSecurity Management
Acer eDataSecurity Management is handy file encryption utility that protexts your files from being accessed by
unauthorized persons. It is conveniently integrated with Windows explorer as a shell extension for quick and
easy data encryption/decryption and also supports on-the-fly file encryption for MSN Messager and Microsoft
Outlook.
The Acer eDataSecurity Management setup wizard will prompt you for a suvervisor password and default
encryption. This encryption will be used to encrypt files by default, or you can choose to enter your won filespecific password when encrypting a file.
NOTE: The password used encrypt a file is the unique key that the system needs to decrypt it. If you lose the
password, the supervisor password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encryped file! Be sure to safeguard all related
passwords!
Chapter 1
31
Acer eLock Management
Acer eLock Management is a security utility that allows you to lock your removable data, optical and floppy
drives to ensure that data can’t be stolen while your notebook is unattended.
T
32
Removable data devices - includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives,
Chapter 1
T
T
T
USB memory card readers, IEEE 1394 disk drives and any other removable disk drives that can be
mounted as a file system when plugged into the system.
Optical drive deivces - includes any kind of CD-ROM or DVD-ROM drives.
Floppy disk drives - 3.5-inch disks only.
Interfaces - includes serial ports, parallel port, infrared (IR), and Bletooth.
To activate Acer eLock Management, a password must be set first. Once set, you can apply locks to any of the
devices. Lock(s) will immediately be set without any reboot necessary, and will remain locked after rebooting,
until unlocked.
NOTE: If you lose your password, there is no method to reset it except by reformatting your notebook or taking
your notebook to anAcer Customer Serivce Center. Be sure to remember or write down your password.
Acer eRecovery Management
Acer eRecovery Management is a powerful utility that does away with the need for recovery disks provided by
the manufacturer. The Acer eRecovery Management utility occupies space in a hidden partition on your
system’s HDD. User-created backups are stored on D:\ drive. Acer eRecovery Management provides you
with:
T
T
T
Password protection.
Recovery of applications and drivers.
Image/data backup:
T
Chapter 1
Back up to HDD (set recovery point).
33
T
T
Back up to CD/DVD.
Image/data recovery tools:
T
Recover from a hidden partition (factory defaults).
T
Recover from the HDD (most recent user-defined recovery point).
T
Recover from CD/DVD.
For more information, please refer to “Acer eRecovery Management”
NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management’s “System backup to optical disk” feature to burn a backup image to CD or DVD. To
ensure the best results when recovering your system using a CD or Acer eRecovery Management,
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications and to monitor the system health
status. Furthermore, Acer eSettings Management enables you to optimize your Windows operating system, so
your computer runs faster, smoother and better.
Acer eSettings Management also:
T
T
34
Provides a simple graphical user interface for navigating.
Displays general system status and advanced monitoring for power users.
Chapter 1
Acer ePerformance Management
Acer ePerformance Management is a system optimization tool that boosts the performance of your Acer
notebook. It provides and express optimization method to release unused memory and disk space quickly. The
user can also enable advanced options for full control over the following option:
T
T
T
Memory optimization - releases unused memory and check usage.
Disk optimization - removes unneeded items and files.
Speed optimization - improves the usability and performance of your Windows XP system.
Chapter 1
35
Acer OrbiCam
The Acer OrbiCam is a 1.3 megapixel CMOS camera appropriately mounted on the top of the LCD panel. The
camera’s 225-degree ergonomic rotation allows you to capture high-resolution photos or videos up front or at
the back of the LCD panel. The Acer OrbiCam fully supports the Acer Video Conference technology so that
you can transmit the best video quality over an instant Messenger service.
36
Chapter 1
Getting to know your Acer OrbiCam
1
#
23
Item
No.
#
Item
1
Item
Lens
2
Power indicator
3
Rubber grip (selected models only)
Rotating the Acer OrbiCam
The Acer OrbiCam rotates 225 degrees counterclockwise to achieve the desired angle. Refer to the
illustrations below:
For your convenience, the camera snaps 45 degrees to match the position of your face in front or at the back
of the LCD panel.
NOTE: Do not rotate the camera clockwise to prevent damage to the device.
Launching the Acer OrbiCam
To launch the Acer OrbiCam, double click on the Acer OrbiCam icon on the screen.
OR
Click Start > All programs > Acer > Acer OrbiCam. The Acer OrbiCam capture windows window appears.
Chapter 1
37
Changing the Acer OrbiCam settings
Resolution
To change the capture resolution, click the displayed resolution at the bottom right corner of the capture
window, then select the desired resolution.
Options
Click Options to display the Window, Preview, and Folder tabs. Use the options to change the capture window
size, preview settings, and the folder for captured photos or videos.
38
Chapter 1
Camera Settings
Chapter 1
T
Basic settings: Click the Camera Settings icon on the bottom right corner of the capture display,
then select Camera Settings from the pop-up menu. You can adjust the Video, Audio, and Zoom/
Face tracking options from this window.
T
Capture settings: From the Camera Settings window, click the Driver Settings button. The
Properties window will appear.
39
T
Device Settings allows you to change the camera brightness, contrast, hue, saturation, sharpness,
etc.
T
Advanced Settings allows you to achieve gain control, implement image mirror, select image
enhancements and anti-flicker settings, and turn on/off the camera indicator.
T
Zoom/Face Track Settings allows you to adjust the zoom level and turn the face tracking feature
on or off.
Capturing photos or videos
To capture a photo or a video clip, rotate the Acer OrbiCam to get the desired angle, then click the Take a
Picture or Record a Video button. The Windows Picture and Fax Viewer or the Windows Media Player
automatically launches to display or play a preview of the photo/video clip.
NOTE: By default, all photos and videos are saved in the My Pictures and My Videos folder.
Using the Acer OrbiCam as webcam
The Acer OrbiCam is automatically selected as the capture device of any instant messenger (IM) application.
To use the Acer OrbiCam as a webcam, open the IM service, then select the video/webcam feature. You can
now broadcast from your location to an IM partner anywhere in the world.
Enabling the Acer VisageON
The Acer VisageON technology comes with two features: Face tracking and Video effects (selected models
only). The Face Tracking feature tracks your head movement and automatically centers your face in the
capture window. The video effects feature allows you to select and apply an effect to your video transmissions.
NOTE: The face tracking feature is not capable of centering your face beyond the capture window frame.
Minimal head movements are tracked more efficiently.
To enable the Acer VisageON:
1. Right click on this icon, then select VisageON from the pop-up menu.
40
Chapter 1
The VisageON window appears as below:
2.
Select and apply a video effect in the left section of the VisageON window. Change the face tracking
settings and options in the right section.
Using the face tracking feature
To use the face tracking feature:
1. Click the left icon down arrow button, then select Single User or Multiple Users from the pop-up menu. For
multiple users, the face tracking feature automatically centers all the users’ face in the capture window,
otherwise the utility centers the face of the user closest to the camera.
2.
Click the right icon to zoom in/out or reset the current view.
3.
Click VisageON to display a menu that allows to change the configuration of the camera, face tracking
and video effects settings.
Chapter 1
41
Using video effects (selected models only)
The Video Settings section allows you to select an avatar or accessory video effect from the list. To select an
effect:
1. Click the encircled icon to display the available video effects. The Video Effect Selection window appears as
below:
2.
Click on a video effect to use. The selected effect appears in the video effects section of the VisageON
window.
NOTE: When using avatars, you may have to calibrate the face points to achieve better tracking. Follow
screen instructions in the VisageON to continue.
NOTE: You may use video effects when using the camera for IM chat/video sessions or call conferences.
42
Chapter 1
Hardware Specifications and Configurations
Processor
Item
Specification
CPU type
®
Intel
®
Intel
Intel®
Pentium
®
M YonahProcessor dual core at 1.66~2.16 GHz
Pentium
®
M Yonah Processor single core at 1.66~1.83 GHz
®
M Yonah Processosr at 1.66~1.83 GHz
Celeron
CPU package
uFCPGA
CPU core voltage
Depend on DVI
CPU I/O voltage
VCCA 1.5V
VCCP 1.05V
System Board Major Chips
Item
Controller
System core logic
ATI RC410ME + SB460
Super I/O controller
N/A
Audio controller
Azalia Audio Controller ALC883
Video controller
ATI 52P/52PG
UMA
Hard disk drive controller
ATI SB460
Keyboard controller
NS PC97551
IrDA controller
N/A
DVI controller
N/A
PCMCIA/ card reader / 1394
controller
TI PCI7412
DDR-soDIMM controller
ATI RC410ME
BIOS
Item
Specification
BIOS vendor
Phoenix
BIOS Version
Phoenix First BIOS
BIOS ROM type
Flash ROM(SST39VF080)
BIOS ROM size
1MB
BIOS package
40 pins TSOP
BIOS password control
Set by setup manual
Item
Specification
Cache controller
Built-in CPU
Cache size
2 MB
1st level cache control
Always enabled
2nd level cache control
Always enabled
Cache scheme control
Always enabled
Chapter 1
43
System Memory
Item
Specification
Memory controller
ATI RC410ME
Memory size
256MB/512MB/1GB
DIMM socket number
2
Supports memory size per slot
1024 MB
Supports maximum memory size
2GB (with dual soDIMM modules)
Supports DIMM type
DDRII SDRAM Standard
Supports DIMM Speed
533/667 MHz
Supports DIMM voltage
1.8V
Memory module combinations
You can install memory modules in any combinations as long as
they match the above specifications.
.
LAN Interface
Item
Specification
Supports LAN protocol
10/100 Mbps Fast Ethernet connection
LAN chip
Marvel 88E8038
LAN connector type
RJ45
LAN connector location
Rear side
.
Wireless LAN
Item
Specification
Card Type
Mini-card/Mini-PCI
Mode
802.11 a/b/g
802.11 b/g
Antenna
Built in 2 antenna(PIFA type)
Support
Wi-Fi, WPA2, WMM, CCX V3/V4
.
Modem Interface
Item
Specification
Data modem data baud rate (bps)
56K ITU
Supports modem protocol
V.90/V.92 AC-Link modem with PTT
approval
Wake-on-Ring ready
Modem connector type
RJ11
Modem connector location
Rear side
VGA
44
Notice
Discrete
UMA
Chipset for suitable VGA type
M52P/M52PG
RC410ME
Video RAM
up to 512MB
up to 256MB
Chapter 1
USB Port
Item
Specification
USB Controller
Integrated with SB460
USB compliancy level
2.0
OHCI
USB 2.0
Number of USB port
3
Location
Rear Side *1
Right Side *2
Audio Port
Item
Specification
Audio Controller
Azalia Audio Controller (Realtek ALC883)
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
20 bit stereo Digital to analog converter
18 bit stereo Analog to Ditial converter
Compatibility
Microsoft PC99/2100, AC97 2.3 & WHQL/WLP2.0
Mixed sound source
CD
Sampling rate
All DACs support 44.1K/48K/96K/192K sample rate
All ADCs support 44.1K/48K/96K sample rate
Internal microphone
Yes
Internal speaker / Quantity
Yes / 2
Support
S/PDIF out / VoIP
PCMCIA Port
Item
Specification
PCMCIA controller
PCI7412
Supports card type
Type II
Number of slots
One
Access location
Right Side
Feature
PC Card Standard 8.1 compliant, ACPI 2.0 compliant, Support PC
Card or CardBus with hot insertion and removal, Support 132MBps
burst transfer
Keyboard
Item
Specification
Keyboard controller
NS PC97551
Keyboard vendor & model name
TravelMate series: New Acer Ergo Keyboard
Aspire series: New Acer flat keyboard
Total number of keypads
Touchpad with 4-way integrated scroll button
Chapter 1
T
88-89 keys Acer Fine TouchTM
keyboard
Yes
45
Keyboard
Item
Specification
12 function keys
Four easy-launch buttons
Two front access LED buttons
T
two Windows keys
T
Hotkey controls
T
embedded numberic keypad
T
Multi-Langue support
T
Spill-proof
T
Internet browser
T
email with LED
T
Empowering key
T
one user-programmable button
T
WLAN LED button
T
Bluetooth LED button
Battery
Item
Specification
Vendor & model name
Sony/Sanyo/Simplo
Battery Type
Li-ion
Pack capacity
65Wh
Number of battery cell
8-cell 2400mAh
6-cell 2000mAh
4-cell 2000mAh
Package configuration
Pin 1
Pin 2
BATT+: Battery+, Battery Positive Terminal
Pin 3
ID : Identify Pin (Note 1)
Pin 4
B/I : Battery-In Pin
Pin 5
TS : Connect to Thermister
Pin 6
SMD : SMBus data interface I/O pin
Pin 7
SMC : SMBus clock interface I/O pin
Pin 8
Pin 9
GND : Battery Negative Terminal
LCD :15.4" WXGA LCD
Item
Vendor & model name
Specification
CMO
N154I1-L0C
GLARE
TYPE/
N154I1-L0B
NON-GLARE
LPL
LP154W01TLB5 GLARE
LEAD-FREE/
LP154W01TLA1 NONGLARE
LEAD-FREE
Samsung
LTN154X3L01-H00
glare L6-G5/
L01-100 nonglare L6-G5/
LTN154P1L02-V LEADFREE
AUO
B154EW01
V9 16MS
LEAD-FREE
GLARE
TYPE
QDI
QD15TL0702 GLARE /
QD15TL0203 NONGLARE
TYPE LEADFREE
Mechanical Specifications
46
Chapter 1
LCD :15.4" WXGA LCD
Item
Specification
LCD display area
(diagonal, inch)
15.4”
15.4”
15.4”
15.4”
15.4”
Active Area(mm)
331.2(H)x
207.0(V)
331.2(H)x
207.0(V)
331.2(H)x
207.0(V)
331.2(H)x20
7.0(V)
331.2(H)x20
7.0(V)
Display technology
TFT
TFT
TFT
TFT
TFT
Resolution
WXGA
(1280*800)
WXGA
(1280*800)
WXGA
(1280*800)
WXGA
(1280*800)
WXGA
(1280*800)
Pixel Pitch
0.2588(H)x0
.2588(V)
0.2588(H)x0
.2588(V)
0.2588(H)x0
.2588(V)
0.2588(H)x0
.2588(V)
0.2588(H)x0
.2588(V)
Pixel Arrangement
RGB
vertical
stripe
RGB
vertical
stripe
RGB
vertical
stripe
RGB
vertical
stripe
RGB
vertical
stripe
Display Mode
Normally
White
Normally
White
Normally
White
Normally
White
Normally
White
Typical White
Luminance(cd/m2)
also called Brightness
200
200/170
200
180
185
Luminance Uniformity
N/A
N/A
N/A
1.25 max.
N/A
Contrast Ratio
400
550/300
300
400
400
Response Time(Optical
Rise Time/Fall Time)
msec
5/11
16(Tr+Tf)
25(Tr+Tf)
12/4
6/10
Power Supply Voltage
+3.3V
+3.3V
+3.0V
+3.3V
+3.3V
Typical Power
Consumption(watt)
4.22
5.23
4.2
6.5
N/A
Weight
600 g
540/575 g
530 g
585 g
585 g
Physical Size(mm)
(Typical)
344(H)x222
(V)x6.2(D)
344(H)x222
(V)x6.2(D)
344(H)x222
(V)x6.2(D)
344(H)x222
(V)x6.5(D)
344(H)x222
(V)x6.35(D)
Electrical Interface
LVDS with 1
pixel/clock
1 channel
LVDS
3.3V LVDS
1 channel
LVDS
Support Color
262144
262144
262144
262K
262144
Viewing Angle(degree)
Horizontal: Right/Left
Vertial: Upper/Lower
45/45
15/35
45/45
15/35
45/45
15/35
45/45
15/35
45/45
15/35
Temperature Range(oC)
Operating
Storage(shipping)
0~+50
-20~+60
0~+50
-20~+60
0~+50
-20~+60
0~+50
-20~+60
0~+50
-20~+60
LCD :15" WXGA LCD
Item
Vendor & model name
Specification
15.0" XGA
NB LCD LPL
LP150X08TLA2 LEADFREE/CHINA
MADE
15.0" XGA
NB LCD CMO
N150X3-L09
REV. C2
Mechanical Specifications
Chapter 1
47
LCD :15" WXGA LCD
Item
Specification
LCD display area
(diagonal, inch)
15.0”
15.0”
Active Area(mm)
304.1(H)x
228.1(V)
304.1(H)x
228.1(V)
Display technology
TFT
TFT
Resolution
XGA
(1024*768)
XGA
(1024*768)
Pixel Pitch(mm)
0.297(H)x
0.297(V)
0.297(H)x
0.297(V)
Pixel Arrangement
RGB
Vertical
stripe
RGB
Vertical
stripe
Display Mode
Normally
White
Normally
White
Typical White
Luminance(cd/m2)
also called Brightness
170
200
Luminance Uniformity
N/A
N/A
Contrast Ratio
250
250
Response Time(Optical
Rise Time/Fall Time)
msec
10/20
5/11
Power Supply Voltage
+3.3V
+3.3V
Typical Power
Consumption(watt)
4.76
3.96
Weight
530 g
550 g
Physical Size(mm)
(Typical)
317(H)x241
(V)x5.9(D)
317(H)x242
(V)x5.7(D)
Electrical Interface
LVDS
IS100C30R-C15
LVDS with 1
pixel/clock
Support Color
262144
262144
Viewing Angle(degree)
Horizontal: Right/Left
Vertial: Upper/Lower
45/45
15/35
45/45
20/40
Temperature Range(oC)
Operating
Storage(shipping)
0~+50
-20~+60
0~+50
-20~+60
AC Adapter
Item
Vendor & model name
Specification
DELTA - 65W, SADP-65KB DBRF YELLOW 1.7X5.5X11 LF
LITEON - 65W, PA-1650-02 QY YELLOW 1.7X5.5X11 LF
LSE - 65W, SLS0335A1957 LF YELLOW 1.7X5.5X11 LF
Input Requirements
48
Chapter 1
Item
Specification
Maximum input current (A,
@100Vac, full load)
1.5A @100Vac input and maximum load
Nominal(Rated) frequency
(Hz)
50 or 60 and single phase
Frequency variation range
(Hz)
47 - 63
Nominal voltages (Vrms)
90 - 265
Efficiency
High efficiency 85% minimum, at 100~240Vac AC input, full load,
warm-up condition.
Output Ratings (CV mode)
Rated output voltage
Offers rated output voltage 19.0V
Voltage Range
18.2V to 19.8V
Noise + Ripple
300mvp-pmax (20MHz bandwidth) for resistor load
Rated Power
90Watts continuously at all specified conditions
Output current
0 A (min.)
to 4.74A (max.)
Dynamic Output Characteristics
Start-up time
2 sec. (@115 Vac and 230Vac full load)
Hold up time
at least 10ms (@115 Vac input, full load)
Over Voltage Protection
(OVP)
30V
Over Current
Protection(OCP)
Output current limit is 6A(Max mode)
Short circuit protection
Output can be shorted without damage, and auto recovery
Electrostatic discharge
(ESD)
15kV (at air discharge)
8kV (at contact discharge)
Dielectric Withstand Voltage
Primary to secondary
3000 Vac for 1 second
Leakage current
less than 250uA at 240Vac, 50Hz
Regulatory Requirements
1. CISPR 22 Class B
2. VCCI Class B
Hard Disk Drive Interface
Item
Specification
Vendor &
Model Name
Segate
SATAST98823AS/
HGST
SATA 1.5G NCQ
MORAGA+HTS5410
80G9SA00
Segate SATA
ST9100824AS LF/
Toshiba
MK1032GSX/
HGST
NCQMORAGA+HTS
541010G9SA00
Segate SATA
ST9120821AS LF/
Toshiba SATAI1.5G
W/NCQ MK1234GSX
Capacity (MB)
80000
100000
120000
Bytes per
sector
1024/512
512
512
Data heads
3/4
4
4
Drive Format
Chapter 1
49
Hard Disk Drive Interface
Item
Specification
Disks
2
2
2
Spindle speed
(RPM)
5400 RPM
5400 RPM
5400 RPM
Performance Specifications
Buffer size
8192KB
8192KB
8192KB
Interface
Serial ATA
Serial ATA
APA7&SATA1.0&SAT
AII(for Toshiba)
Serial ATA
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
57.6/61.6
57.6/57.6/61.6
57.6
Data transfer
rate
(host~buffer,
Mbytes/s)
150 MB/Sec.
SATA 1.0
150 MB/Sec.
150 MB/Sec.
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Voltage
tolerance
5V(DC) +/- 5%
8X Super Multi Interface
Item
Vendor & model name
Specification
PHILIPS SDVD8821
PIONEER DVR-K16RS
Transfer rate (KB/sec)
Sustained:
Max 10.9Mbytes/sec
Sustained:
DVD: Max 10.8Mbytes/sec
CD: 3.6Mbytes/sec
Access Time(DVD)
Random Access: 130 ms
Full Stroke: 240 ms
Random Access: 150 ms
Full Stroke: 300 ms
Buffer Memory
2MB
2MB
Interface
Compliant to ATA/ATAPI-5
ATAPI interface(SFF-8020, SFF-8090)
Applicable disc format
DVD(Read): DVD-ROM, DVD-Video,
DVD-Audio, DVD-R, DVD-R 3.95GB,
DVD-R Multi-Border, DVD-RW,
DVD+R, DVD+R DL, DVD+R MultiSession, DVD+RW, DVD-RAM
CD(Read): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, CD-i, CD-i Bridge,
Video-CD(MPEG-1), Karaoke CD,
Photo-CD, Enhanced CD, CD Plus,
CD Extra, itrax CD, CD-Text, CD-R,
and CD-RW
DVD(Write): DVD Data&Video
CD(Write): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, CD-i, Video-CD, CDText
KODAK Photo CD Single and Multisession, CD Extra(CD PLUS), Video
CD, CD text data(Read/Write), CD-R
discs(Read/Write), CD-RW
discs(Read/Write), DVD-ROM, DVD-R
ver2.00 for general(Read/Write), DVDR DL ver3.0(Read/Write), DVD-RW
ver1.0&1.1&1.2(Read/Write), DVD+R
ver1.0&1.11&1.2(Read/Write), DVD+R
DL ver1.0(Read/Write), DVD+RW
ver1.1&1.2(Read/Write), DVD+RW
high speed ver1.0(Read/Write), DVDRAM ver2.0&2.1&2.2(Read/Write)
Loading mechanism
Load: Manual
Drawer loading mechanism
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
Performance Specification
Power Requirement
Input Voltage
50
Chapter 1
DVD-Dual Interface
Item
Specification
Vendor & model name
PHILIPS SDVD8441
PIONEER DVR-K16RA
Transfer rate (KB/sec)
Sustained:
Max 10.9Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Access Time(DVD)
Random Access: 130 ms
Full Stroke: 240 ms
Random Access: 150 ms
Full Stroke: 300 ms
Buffer Memory
2MB
2MB
Interface
Compliant to ATA/ATAPI-5
ATAPI interface
Applicable disc format
DVD(Read): DVD-ROM, DVD-Video,
DVD-Audio, DVD-R, DVD-R 3.95GB,
DVD-R Multi-Border, DVD-RW,
DVD+R, DVD+R DL, DVD+R MultiSession, DVD+RW
CD(Read): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, CD-i, CD-i Bridge,
Video-CD(MPEG-1), Karaoke CD,
Photo-CD, Enhanced CD, CD Plus,
CD Extra, itrax CD, CD-Text, CD-R,
and CD-RW
DVD(Write): DVD Data&Video
CD(Write): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, CD-i, Video-CD, CDText
DVD(Read): DVD-5/9/10/18, DVD-R
3.95G/4.7G, DVD-R DL, DVD-RW,
DVD+R, DVD+R DL, DVD+RW,
DVD+RW high speed, DVD-RAM v2.0/
2.1
CD(Read): CD-DA, CD-ROM Mode-1,
CD-ROM/XA Mode-2 Form-1 and
Mode-2 Form-2, Photo CD, Video CD,
CD-DA, CD-Extra, Mixed-CD, CDText, CD-R, CD-RW, HS CD-RW, US
CD-RW, US+ CD-RW
DVD(Write): DVD-R, DVD-RW,
DVD+RW
CD(Write): CD-DA, CD-i, Video-CD,
CD-Text, Photo CD, CD-Extra, MixedCD, CD-R, CD-RW, HS CD-RW, US
CD-RW, US+ CD-RW
Loading mechanism
Load: Manual
Drawer loading mechanism
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
Performance Specification
Power Requirement
Input Voltage
Combo Drive Interface
Item
Vendor & model name
Specification
QSIPHILIPS SCB5265
PANASONIC UJDA-770 HLDS GCC-4244N
Transfer rate (KB/sec)(DVD)
Sustained:
Max 11.2Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Sustained:
Max 11.8Mbytes/sec
Access Time
DVD: Random Access: 126 ms
DVD:Full Stroke: 165 ms
DVD: Typical:180 ms
Average:
CD-ROM110ms
DVD-ROM 120ms
Performance Specification
Buffer Memory
2MB
2MB
2MB
Interface
Compliant to ATA/ATAPI-5
ATAPI interface
ATAPI interface
Chapter 1
51
Combo Drive Interface
Item
Specification
Applicable disc format
DVD(Read): DVD 5/9/10/18,
DVD-ROM, DVD-Video, DVD-R
3.95G/4.7G, DVD-RW, DVD+R,
DVD+RW, Multi-Border DVD-R/
DVD-RW, Multi-Session
DVD+R, DVD+RW and DVDRAM
CD(Read): CD-DA, CD-ROM
Mode-1, CD-ROM/XA Mode-2
Form-1 and Mode-2 Form-2,
CD-i Ready, Video-CD(MPEG1), Karaoke CD, Super Video
CD, Photo-CD, Enhanced CD,
CD Plus, CD Extra, i-trax CD,
CD-Text, CD-R, CD-RW
CD(Write): CD-DA, CD-ROM
Mode-1, CD-ROM/XA Mode-2
Form-1 and Mode-2 Form-2,
CD-i, Video-CD, CD-Text
CD: CD-DA, CD-ROM,
CD-R, CD-RW, CDROM XA,
PhotoCD(MultiSession)
DVD: DVD-ROM, DVDVideo, DVDRAM(2.6GB/4.7GB),
DVD-R, DVDRW(Ver1.1), DVD+R,
DVD+RW
1. Reads and writes data
in each CD-ROM, CDROMXA, CD-I FMV,
Video CD, and CDEXTRA
2. Reads data in Photo
CD( Single and Multi
session)
3. Reads and writes
standard CD-DA
4. Reads and writes CDR
5. Reads and writes CDRW
6. Reads data in DVDROM
Loading mechanism
Load: Manual
Load: Manual
Load: Manual
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
5 V +/- 5 % (Operating)
Power Requirement
Input Voltage
Power Management
ACPI Mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (S5)
OS initiated shutdown. All devices in the system are turned
off completely.
Working (S0)
Individual devices such as the CPU and hard disk may be
power managed in this state.
Suspend(S3)
CPU Power Down
VGA Power Down
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
Super I/O Power Down
Sleeping State (S4)
Also called Hibernate state. System saves all system
states and data onto the disk prior to power off the whole
system.
Dimensions and Weight
Item
Details
Model
AS 5600/3680&TM 4220/2480
Deminsions
Weight
52
364(W) x 275(D) with max. 30/35.2mm(H)
<2950 g except TV SKU for 15.4” WXGA LCD model
<2940 g for 15” XGA LCD model
Chapter 1
Environmental Requirements
Item
Specification
Temperature
Operating
+5 ~ +35°C
Non-operating
-20 ~ +65°C (storage package)
Humidity
Operating
20% ~ 80% without condensation
Altitude
Operating sea level 0 to 10,000ft
Storage sea level 0 to 40,000ft
Chapter 1
53
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However,
if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
The setup screen displays BIOS as follows:Navigating the BIOS Utility
Function
Item
Information
Display the system informations
Main
Allows the user to specify standard IBM PC AT
system parameters
Advanced
Provides advanced settings of the system
Security
Provides security settings of the system
Boot
Allows the user to specify the boot options
Exit
Allows the user to save CMOS setting and exit Setup
During setup,all Fn function keys and power saving functions are disabled.
There are five menu options: Main, Advanced, Security, Boot and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press p or q.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values.
Chapter 2
54
Information
PhoenixBIOS Setup Utility
. Info.
Main
CPU Type:
:
CPU Speed
:
Advanced
Security
Boot
Exit
Genuine Intel(R) CPU T2600@2.16GHz
2130 MHz
IDE1 Model Name:
ST9100824AS
IDE1 Serial Number: 3PL022FK
System BIOS Version: v0.3301
EC BIOS Version:
0.13
Serial Number:
LXT123ZH2000470082EF00
Asset Tag Number:
Product Name:
Manufacturer Name:
TravelMate xxxx
Acer
UUID:
E0A62208C08BD811BCFB00163631BD37
F1 Help
↑ ↓
←→
Esc Exit
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
Parameter
55
Description
CPU Type
This item will show the CPU information of the system.
CPU Speed
This item will show the CPU clock speed.
IDE1 Model Name
This item will show the Model name of HDD installed on Primary IDE
master. The hard disk model name is automatically detected by the
system. If there is no hard disk present or unknown type, “None”
should be shown on this field
IDE1 Serial Number
This item will show the Serial number of HDD installed on Primary IDE
master. If no Hard disk or other devices are installed on Primary IDE
master, then it will display a blank line
System BIOS Version
This field reports the BIOS version of system
VGA BIOS Version
This field reports the VGA version of the system
KBC Version
This field reports the keyboard controller version of the system
Serial Number
This item will show the Serial number of system.
Asset Tag Number
This item will show the Asset Tag number of the system.
Product Name
This field will show product name.
Manufacturer Name
This field will show manufacturer name.
UUID
This will be visible only when there is an internal LAN device present.
Chapter 2
Main
This menu provides you the information of the system.
PhoenixBIOS Setup Utility
Info.
Advanced
Main
Security
Boot
Exit
Item Specific Help
System Time:
[11:59:38]
System Date:
[03/16/2006]
System Memory:
640 KB
Extended Memory:
1014 KB
Video Memory
128 MB
Quiet Boot:
[Enabled]
Power on Display:
[Auto ]
Network boot
[Enabled]
F12 Boot Menu:
[Disabled]
D2D Recovery:
[Enabled]
<Tab>, <Shift-Tab>, or
<Enter> selects field.
F1 Help
Esc Exit
↑↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Parameter
Description
System Time / System
Date
The hours are displayed with 24 hours format. The values set in these two fields
take effect immediately.
System Memory
This field reports the memory size of system base memory. The size is fixed to
640KB.
Extended Memory
This field reports the memory size of the extended memory in the system.
Extended Memory size = Total memory size - 1 MB
Video Memory
VGA Memory size = 128MB
Quiet Boot
Customer Logo display will be shown during POST when it is selected.
Power on display
Auto: During power on process, the system will detect if any display
device is connected on external video port. If any external display device is
connected, the power on display will be in CRT (or projector) only mode.
Otherwise it will be in LCD only mode.
Both: Simultaneously enable both the integrated LCD screen and the system’s
external video port (for an external CRT or projector).
Network boot
When this is selected, Boot from LAN feature is enabled. When this is not
selected, Boot from LAN feature is then disabled.
Chapter 2
56
Parameter
57
Description
F12 Boot Menu
When this is selected, users can modify device boot priority by pressing F12 key
during POST. When this is not selected, device boot priority will not be
adjustable during POST.
D2D Recovery
Allow user to enable/disable the Disk-to-Disk recovery
Chapter 2
Security
The Security screen contains parameters that help safeguard and protect your computer from
unauthorized use.
Info.
PhoenixBIOS Setup Utility
Security
Advanced
Main
Supervisor Password Is:
Clear
User Password Is:
Clear
Supervisor Password
controls accesses of the
[Enter]
Set HDD Password
HDD Password Is:
Password on Boot:
[Enter]
Clear
[Disabled]
Esc Exit
↑ ↓
←→
Exit
Item Specific Help
Set Supervisor Password
Set User Passord
F1 Help
Boot
setup utility.
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen. Settings in boldface are the default and
suggested parameter settings.
Parameter
Supervisor Password Is
Description
N/A
Option
N/A
User Password Is
N/A
N/A
HDD Password Is
N/A
N/A
Set Supervisor Password
Press Enter to set the administrator
password. When set, this password
protects the BIOS Setup Utility from
unauthorized access.
[Set]: System password is set
[Clear]: System password is not set
Length -- No more than 8
characters
Characters -- 0-9, A-Z (not
case sensitive)
Set User Password
Chapter 2
58
Parameter
Description
Option
Set HDD Password
When shown as [Locked], the hard drive
password currently can not be changed
or disabled.
To change or disable it, turn off the
system and enter Setup immediately after
turning it back on.
Press [Enter] to input change, or disable
hard drive password.
Enter
Password on boot
Defines whether a password is required
or not while the events defined in this
group happened. The following suboptions are all requires the Supervisor
password for changes and should be
grayed out if the user password was used
to enter setup.
Allows the user to specify whether or not
a password is required to boot.
Disabled
Enabled
Set Supervisor/User Password
If password on boot is required, the password must be set otherwise it cannot be enabled.
The formats of the password are as follows:
Length
Characters
No more than 8 characters
0-9,A-Z (not case sensitive)
While these fields are highlighted and press “Enter”, a window similar to the following is shown:
Set SupervisorPassword
Enter New Password
[
]
Confirm New Password
[
]
If there is an old password then setup will prompt with the following window instead and a current password
will be required to be entered at first:
Set Supervisor Password
59
Enter current password
[
]
Enter New Password
[
]
Confirm New Password
[
]
Chapter 2
User can now type password in field “Enter New Password”, and re-enter password in field “Confirm New
Password” for verification.
If the verification is OK:
The password setting is complete after user presses enter.
Setup Notice
Changes have been saved.
[ continue]
If the current password entered does not match the actual current password:
Setup Warning
Invalid password
Re-enter Password
[ continue]
If the new password and confirm new password strings do not match:
Setup Warning
Password do not match
Re-enter Password
Chapter 2
60
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable
devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM
in module bay and onboard LAN device.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Boot
Security
Item Specific Help
Boot priority order:
1: USB KEY:
2: USB FDC:
3: USB HDD:
4: IDE 0:
ST9100824ASIDE S
6: 1394 CDROM
7: PCI LAN: MBA v8.2.6 Slot 0300
8:
Excluded from boot order:
: PCI LAN:
: USB HDD:
: USB CDROM:
: USB FDC:
: USB KEY:
F1 Help
↑ ↓
MBA v8.2.6 Slot 0300
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Parameter
Boot priority order
Keys used to view or
configure devices:
Up and Down arrows
select a device.
<+> and <-> moves
the device up or down.
<f> and <r> specifies
the device fixed or
removable.
<x> exclude or include
the device to boot.
<Shift + 1> enables or
disables a device.
<1- 4 > Loads default
boot sequence.
Select Item
←→
Esc Exit
Exit
Description
Keys used to view or configure devices: Up and Down
arrows select a device. <+> and <-> movew the device up
or down. <f> and <r> specifies the device fixed or
removable.
>
<x> exclude or include the device to boot.
<Shift +1> enables or disables a device.
<1-4> Loads default boot sequence.
.
61
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1 Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Description
Exit Saving Changes
Exit System Setup and save your changes to CMOS
Exit Discarding
Changes
Exit utility without saving Setup data to CMOS
Load Setup Default
Load default values for all SETUP items
Discard Changes
Load previous values from CMOS for all SETUP items
Save Changes
Save Setup Data to CMOS
Chapter 2
62
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screwdriver
T
Plastic flat head screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
63
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3.
Remove the battery pack.
NOTE: There are several types of screws used to secure bottom case and upper case assembly. The screws
vary in length. Please refer the picture below, group the same type of screws together during service
disassembling. Please also remember the screw location for each screw type. If you fasten the screw to
the wrong location, the screw may be too long to damage the main board.
64
Chapter 3
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Chapter 3
65
Removing the Adapter and Battery Pack
66
1.
Unplug the adapter.
2.
Release the battery lock.
3.
Slide the battery latch.
4.
Remove the battery pack.
Chapter 3
Removing the Heatsink Module, CPU, and HDD Modue
Remove the Heatsink Cover
1.
Release the six screws securing the heatsink cover. (The six screws are attached to the heatsink cover)
2.
Lift the heatsink cover up and remove it.
Remove the Heatsink Module
1.
Disconnect the main fan cable from the mainboard.
2.
Remove the seven screws securing the heatsink module.
3.
Remove the heatsink module from the main unit.
Removing the HDD Module
1.
Release the two screws securing the HDD cover. (One screw is attached to the HDD cover)
2.
Remove the HDD cover.
Chapter 3
67
.
3.
Remove the screw securing the HDD.
4.
Holding the mylar and pull the HDD module out of the main unit.
Removing the CPU
68
1.
Use a flat screw driver and turn the screwdriver counterclockwise to unlock the CPU.
2.
Remove the CPU from the mainboard.
Chapter 3
Removing the Memory and Wireless Card
Remove the Memory
1.
Press the latch on left and right side to pop out the memory and remove it.
2.
Remove the other memory.
Chapter 3
69
Removing the Bluetooth Module
70
1.
Remove the screw securing the Bluetooth module.
2.
Remove the Bluetooth connector from the mainboard.
3.
Remove the Bluetooth cable from the Bluetooth wire groove.
4.
Remove the Bluetooth module from the main unit.
5.
Remove the two screws securing the Bluetooth bracket.
6.
Remove the Bluetooth module from the Bluetooth bracket.
7.
Disconnect the Bluetooth cable from the Bluetooth module.
Chapter 3
Disassembling the Main Unit into Upper Case and Lower Case
1.
Disconnect the power cable from the mainboard.
1.
Remove the three screws securing the middle cover on the rear panel.
2.
Open the notebook.
3.
Release the clasp of middle cover and remove the middle cover from the main unit.
4.
Remove the two screws securing the keyboard.
5.
Turn the keyboard over.
6.
Unlatch the keyboard FFC latch and remove the keyboard from the main unit.
.
Chapter 3
71
7.
Disconnect the LCD cable from the mainboard as shown.
8.
Remove the two screws on left and right hinges.
9.
Remove the LCD module from the main unit and be careful to pull the antenna out.
10. Remove the screw securing the ODD module.
11. Push the ODD module out of the main unit.
12. Remove the five screws securing the upper case.
13. Remove the 22 screws securing the lower case.
72
Chapter 3
14. Disconnect the LID switch cable from the mainboard.
15. Disconnect the MIC wire cable from the mainboard.
16. Unlatch the touchpad board FFC and disconnect the touchpad board FFC from the mainboard.
17. Lift up the upper case to separate the upper and lower case.
Chapter 3
73
Disassembling the LCD Module
1.
Remove the four screw caps from the LCD module.
2.
Remove the four screw securing the LCD bezel.
NOTE: For LCD module with CCD, please refer to following steps.
1.
Remove the six screw caps for the LCD module.
2.
Remove the six screws securing the LCD module.
3.
Remove the LCD bezel.
4.
Remove the 13 screws securing the LCD panel.
Chapter 3
74
5.
For LCD with CCD, remove the 11 screws securing the LCD panel.
6.
Lift up the inverter board.
7.
DIsconnect the inverter cables from the inverter board and remove the inverter board.
8.
Remove the LCD panel from the LCD cover.
9.
Remove the two screws securing the left LCD brackets.
10. Remove the left LCD bracket from the LCD panel.
11. Remove the two screws securing the right LCD bracket.
12. Remove the right LCD bracket from the LCD panel.
13. Remove the tape on the LCD cable.
75
Chapter 3
14. Disconnect the LCD cable and remove the LCD cable from the LCD panel.
15. This completes the LCD module disassembly.
Remove the CCD module
1.
Remove the five screws securing the CCD brackets and remove the CCD brackets
2.
Lift the CCD plastic bracket up.
3.
Remove the CCD module.
4.
Be careful that the CCD cable is combined with the antenna.
CCD
Antenna
Chapter 3
Antenna
76
Reassembling the LCD Module
77
1.
Connect the LCD cable to the LCD panel.
2.
Place the tape on the LCD cable.
3.
Place the right LCD bracket back to the LCD panel
4.
Secure the right LCD bracket with the two screws.
5.
Place the left LCD bracket back to the LCD panel
6.
Secure the left LCD bracket with the two screws.
7.
Place the LCD panel back to the LCD cover.
8.
Place the inverter board back to the LCD module and connect the inverter cables to the inverter board.
9.
Secure the LCD panel with the 13 screws.
Chapter 3
10. Place the LCD bezel back to the LCD module. Push each side of the bezel to make it clip to the LCD
cover well.
11. Secure the LCD bezel with four screws.
12. Place the four screw caps back.
13. This completes the LCD module reassembly.
Chapter 3
78
HDD disassembly & Reassembly
79
1.
Remove the four screws securing the HDD bracket.
2.
Remove the HDD bracket from the HDD.
3.
Place the HDD bracket back to the HDD.
4.
Secure the HDD with the four screws.
5.
This completes HDD module disassembly and reassembly.
Chapter 3
ODD disassembly & Reassembly
1.
Remove the four screws securing the ODD module.
2.
Remove the ODD bracket from the ODD.
3.
Place the ODD bracket back to the ODD.
4.
Secure the ODD with the four screw.
5.
This completes ODD module disassembly and reassembly.
Chapter 3
80
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model. Non-Acer products, prototype cards, or modified
options can give false errors and invalid system responses.
1.
Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.
Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic
test or by repeating the same operation.
3.
Disassemble and assemble the unit without any power sources.
4.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 83.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 85
“Undetermined Problems” on page 97
POST detects an error and displayed messages
on screen.
“Error Message List” on page 86
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 85
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 85
“Intermittent Problems” on page 96
“Undetermined Problems” on page 97
Chapter 4
81
System Check Procedures
External Diskette Drive Check
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
82
Chapter 4
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
Chapter 4
“Check the Battery Pack” on page 84
83
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the PS/2 mouse does not work, then check if the main board to switch board FPC is connected O.K.
4.
If the main board to switch board FPC is connected well, then check if the FCC on touch pad PCB
connects properly.
5.
If the FFC on touch pad PCB connects properly, then check if LS851 JP1 Pin6=5V are pulese. If yes, then
replace switch board. If no, then go to next step.
6.
Replace touch pad PCB.
7.
If the touch pad still does not work, then replace FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
84
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 97.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
85
Index of Error Messages
Error Message List
Error Messages
FRU/Action in Sequence
Struck Key
See “Keyboard or Auxiliary Input Device Check” on page 82
System CMOS checksum bad - Default
configuration used
RTC battery
Real time clock error
Run BIOS Setup Utility to reconfigure system, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
Previous boot incomplete - Default configuration
used
“Load Default Settings” in BIOS Setup Utility.
RTC battery
Main baord
Invalid System Configuration Data
“Load Default Settings” in BIOS Setup Utility.
Main board
Operating system not found
Enter Setup and see if fixed disk and drive A are properly identified.
Dikette drive
Hard disk drive
Main board
86
Chapter 4
Error Message List
No beep Error Messages
Power-on indicator turns off and LCD is blank.
FRU/Action in Sequence
Power source (battery pack and power adapter.) See “Power
System Check” on page 83
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
Main board.
Power-on indicator turns on and LCD is blank.
Power source (battery pack and power adapter.) See “Power
System Check” on page 83
Reconnect the LCD connector
Hard disk drive
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and LCD is blank.
But you can see POST on an external CRT.
Reconnect the LCD connectors.
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and a blinking cursor
shown on LCD during POST.
Chapter 4
Ensure every connector is connected tightly and correctly.
Main board
87
Phoenix BIOS Beep Codes
Code
Beeps
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
07h
Disable shadow and execute code from the
ROM.
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
22h
1-3-1-3
24h
Test DRAM refresh
Test 8742 Keyboard Controller
Set ES segment register to 4 GB
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
Enable cache before system BIOS shadow
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
41h
Initialize extended memory for RomPilot.
42h
Initialize interrupt vectors
45h
46h
88
POST Routine Description
02h
POST device initialization
2-1-2-3
Check ROM copyright notice
Chapter 4
Code
Beeps
POST Routine Description
47h
Initialize I20 support
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
55h
Enable USB devices
58h
59h
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Data Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
Chapter 4
89
Code
POST Routine Description
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B1h
Inform RomPilot about the end of POST.
B2h
POST done- prepare to boot operating system
B4h
90
Beeps
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B7h
Initialize ACPI BIOS
B9h
Prepare Boot
BAh
Initialize SMBIOS
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
Chapter 4
Code
Beeps
POST Routine Description
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
CAh
Redirect Int 15h to enable remote keyboard
CBh
Redirect Int 13h to Memory Technologies
Devices such as ROM, RAM, PCMCIA, and
serial disk.
CCh
Redirect Int 10h to enable remote serial video
CDh
Re-map I/O and memory for PCMCIA
CEh
Initialize digitizer and display message.
D2h
Unknown interrupt
The following are for boot block in Flash ROM
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
F5h
1
Output one beep
Clear Huge Segment
F6h
Boot to Mini DOS
F7h
Boot to Full DOS
Chapter 4
91
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
First, plug a monitor to CRT port. Next, enter BIOS utility to running
“Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
LCD is too dark
LCD brightness cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Reconnect the LCD cable
Missing pels in characters
LCD cable
Abnormal screen
LCD
Wrong color displayed
Main board
LCD has extra horizontal or vertical lines
displayed.
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but system
runs correctly
Main board
HDD/CD-ROM active indicators cannot work
HDD/CD-ROM drive
Device driver
Main board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 83.
Battery pack
AC adapter
See if the thermal module is overheat (Heat sink or fan).
Main board
The system cannot power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 83.
Battery pack
Power adapter
CPU
Main board
The system cannot power-off.
In Windows XP operating system, hold and press the power switch
for more than 4 seconds. If the system can power off, then the main
board is OK. Verify OS in the HDD.
Main board
92
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged or discharged
Action in Sequence
See “Check the Battery Pack” on page 84.
Battery pack
Main board
System hang during POST
ODD/HDD/FDD/RAM module
Main board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
PC Card cannot be inserted or ejected
Check if the PCMCIA slot is blocked
Main board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot system.
RAM module
Main board
Check BIOS revision
System can power on, but you hear two long
beeps: “B--, B--” and the LCD is blank.
Reinsert DIMM
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
OS volume control
Audio driver
Speaker
Main board
Internal speakers make noise or emit no sound.
Speaker
Main board
Microphone cannot work
Audio driver
Volume control in Windows XP
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation mode
Action in Sequence
Power option in Windows XP
Hard disk drive
Main board
The system doesn’t enter standby mode after
closing the lid of the portable computer.
Driver of Power Option Properties
Lid close switch in upper case
Main board
Chapter 4
93
Power Management-Related Symptoms
Symptom / Error
The system doesn't resume from hibernation/
standby mode.
Action in Sequence
Connect AC adapter then check if the system resumes from
Standby/Hibernation mode.
Check if the battery is low.
Hard disk drive
Main board
The system doesn't resume from standby mode
after opening the lid of the portable computer.
LCD cover switch
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Refresh battery (continue use battery until power off, then charge
battery).
Main board
Battery pack
Main board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Main board
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the
installed devices.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then
reboot system.
Reconnect hard disk/CD-ROM drives/FDD or other peripherals.
Main board
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Keyboard
Main board
USB does not work correctly
Main board
Print problems.
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Run printer self-test.
Printer driver
Printer cable
Printer
Main board
Parallel port device problems
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Device driver
Device cable
Device
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
Main board
94
Chapter 4
Modem/LAN-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Internal LAN does not work correctly
Lan cable
Driver
Main board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 97.
Chapter 4
95
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
96
1.
Run the diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 83):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
T
System board
T
LCD assembly
97
Chapter 5
Jumper and Connector Locations
Top View
RJ11/RJ45
VRAM
Battery Connector
Charger IC
LCD + PC Camera
Connector
CPU Power
Converter IC
Clock Gen
Touch Pad +Phone Jack
Connector
Keyboard Connector
USB 2.0 X 2
Modem Connector
5V/3V Converter IC
EC Controller
Audio Codec
5-in-1
Chapter 5
Card Bus IC
DDR Power IC
BIOS
98
Bottom View
RJ11/RJ45
USB 2.0 X1
DC Jack
Mini Card
Battery
Connector
VRAM
CRT
Connector
LAN Controller
ODD
Connector
VGA Power IC
VGA
North Bridge
NB Power IC
CPU
USB 2.0 X2
Bluetooth
CON.
Mini PCI Card
South Bridge
HDD
PATA/SATA
Audio AMP
PCMCIA
Card
RTC Batt
Blue tooth SW
99
Wireless SW
DDR II Memory
Connector
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 3660.
Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please also note that there are some common parts for TravelMate 2460
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information
available on your regional web or channel. For whatever reasons a part number change is made, it
will not be noted on the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS,
your Acer office may have a DIFFERENT part number code from those given in the FRU list of this
printed Service Guide. You MUST use the local FRU list provided by your regional Acer office to
order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
NOTE: Please visit website http://aicsl.acer.com.tw/spl/ for the up to date SPL
Chapter 6
100
Exploded Diagram
Item
101
Description
Item
Description
1
LCD bezel
22
Screw M2.5*6-I(BNI)(NYLOK)
2
LCD hinge-left
23
Screw M2.5*5.0-I(NI)(NYLOK)
3
LCD hinge-right
24
Screw M2.0*3.0-I-NI-NYLOK
4
LCD cover
25
ODD holder
5
CCD module(optional)
26
LCD cable
6
CCD cover(optional)
27
Touchpad board to mainboard
cable
7
Middle cover
28
Bluetooth cable
8
Keyboard
9
Upper case
10
Battery
Chapter 6
Item
Description
11
Mainboard
12
VGA support
13
CPU support
14
Heatsink module
15
Lower case
16
ODD module
18
HDD module
19
HDD cover
20
Bluetooth bracket
21
Heatsink cover
Item
1
Item
Description
Part Name
Item
Part Name
15.4” w/ CCD LCD cover(Aspire)
13
Conductive tape EP
2
ACER logo(Aspire)
14
LCD cover protect sheet
3
15.4” wide w/ CCD LCD knob
15
LCD CCD cover mylar
4
15.4” wide w/ CCD LCD latch
16
CCD cover protect
5
CCD latch BK-L
17
CCD cover
6
CCD latch BK-R
18
CCD bezel
7
LCD spring
19
CCD LED lens
8
15.4 w/ CCD cover shield
20
CCD name plate assy
9
screw M2.5*3.0-I(BNIXNYLOK)EP
21
CCD hinge
Chapter 6
102
Item
103
Part Name
Item
Part Name
10
screw M2.0*3.0-I(NIXNYLOK)
22
camera V-UBDOEM1(CMOS module,
1.3M)
11
CCD cable maylar
23
LCD rubber-1
12
cable assy CCD (5P/4P/R2A) L-F
24
CCD bezel rotect
Chapter 6
Part List
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
ADAPTER
"ADAPTER DELTA - 65W, SADP-65KB
DBRF YELLOW 1.7X5.5X11 LF"
ZL6C ADP 19V DELTA S/P
ADAPTER
"ADAPTER LITEON - 65W, PA-1650-02
QY YELLOW 1.7X5.5X11 LF"
ZL6C ADP 19V LITEON S/P AP.06503.013
ADAPTER
"ADAPTER LSE - 65W, SLS0335A1957
LF YELLOW 1.7X5.5X11 LF"
ZL6C ADP 19V LSE S/P
AP.06506.004
"LI-MN BODENSEE 4CELL2.0 (SANYO
PACK 2,000MAH Y)"
ZB1 SANYO 4CELL 2.0 (W/
SONY) S/P
BT.00403.009
BATTER SONY 4 CELL LI
LIP4084QUPC SY6 4S1P 2.0A LF
ZB1 BAT(Lite-on 4 cell w/
Sony pack) S/P
BT.00404.004
BATTERY SIMPLO PACK 4 CELL LIMN 916C4820F 4S1P 2.0A
ZB1 BATT LI 916C4820FS/
P
BT.00407.007
BATTERY SANYO LI-MN 6
3UR18650Y-2-QC236 3S2P 11.1V 4A
ZB1 BATT LI 3UR18650Y-2- BT.00603.016
QC236 S/P
BATTERY SONY LI-ION 6 CELL
LIP6198QUPC SY6 3S2P 11.1V 4A
ZB1 BATT LI LIP6198QUPC
S/P
BT.00604.007
BATTERY SIMPLO PACK LI-MN 6
CELL 916C4890F 3S2P 10.8V 4.0A
ZB1 BATT LI 916C4890F
3S2P S/P
BT.00607.001
"BATTERY PACK SANYO LI 8CELLl2.4
4.8Ah (4UR18650F-2-QC218,4S2P)
ROHS"
ZB1 sanyo 8CELL 4.4A S/P
BT.00803.014
BOARD
MODEM 56K(MDC) T60M893.10
ZB3 MODEM 56K(MDC)
T60M893.10 S/P
54.ACZV7.001
BOARD
BLUETOOTH MODULE FOXCONN
T60H928.01
ZC1 FOX
BLUETOOTH(T60H928.01)
S/P
54.TAXV7.001
BOARD
MINI PCI WIRELESS BOARD
ABT_ATH5413BG Atheros T60N874.05
ZL6 WIRELESS LAN S.P.
54.A50V7.002
BOARD
MINI PCI WIRELESS BOARD
ABT_BRM4318BG BCM T60H906.01
ZL5 WIRELESS LAN
BOARD S.P
54.A51V7.002
TOUCHPAD BOARD W/AUDIO PORT
ZB3 TP&AUDIO BOARD
ASSY S/P
55.ACZV7.001
CCD MODULE W/CABLE
ZB2 CCD MOUDLE0.3M
W/CABLE S/P
57.AB1V7.001
MODEM CABLE
"ZB2 CABLE ASSY
MODEM (2P/2P,1A) S/P"
50.TCFV7.001
ADAPTER
AP.06501.010
BATTERY
BOARD
DIGITAL LIGHT DEVICE
CABLE
CABLE
Chapter 6
104
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
BLUETOOTH CABLE
ZB1 BLUETOOTH CABLE
S/P
50.AA7V7.002
FFC CABLE - TP TO MB
ZB3 CABLE TP FFC S/P
50.ACZV7.001
FFC CABLE - TP TO TP BOARD
ZB1 CABLE TP/B FFC S/P
50.AA7V7.004
CABLE
POWER CORD US 3PIN ROHS
ZB1 PWR CORD US S/P
27.TAXV7.001
CABLE
POWER CORD EU 3 PIN ROHS
ZB1 PWR CORD (CEE) S/P 27.TAXV7.002
CABLE
POWER CORD PRC (3 PIN)
ET2S POWER CORD S/PPRC
27.A03V7.003
CABLE
POWER CORD (UK)
ET2S POWER CORD
SPARE PART-UK
27.A03V7.004
CABLE
POWER CORD DANISH (3 PIN)
ET2S POWER CORD S/PDANISH
27.A03V7.006
CABLE
POWER CORD AF-S (INDIA)
ZL6A POWER CORD S/P
INDIA S.P.
27.A50V7.001
CABLE
POWER CORD ISRAEL (3 PIN)
ZL6A POWER CORD S/PISR S.P
27.A50V7.002
CABLE
POWER CORD AU W/LABEL (3 PIN)
ZL6A POWER CORD S/PAU S.P.
27.A50V7.003
CABLE
POWER CORD US-110V (BSMI)
ZL3E POWER CORD S/PTWN
27.A99V7.002
CABLE
POWER CORD AF (3 PIN)
ZI5 POWER CORD S/P-AF
27.T48V7.001
CABLE
POWER CORD THAI
ZL3E POWER CORD S/PTHAI
27.A99V7.003
CABLE
POWER CORD SWISS 3 PIN
ZE1 POWER CORD 3P
SWISS S.P.
27.A99V7.004
CABLE
POWER CORD ITALIAN 3PIN
EI2 POWER CORD 3P
ITALY S.P.
27.A99V7.005
CABLE
POWER CORD JAPAN
ZB1 POWER CORD
(JAPANESE) ROHS S/P
27.TAXV7.003
ZB1 AS K/B COVER ASSY
S/P
42.AA7V7.001
CASE/COVER/BRACKET ASSEMBLY
MIDDLE COVER
105
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
CASE/COVER/BRACKET
ASSEMBLY
UPPER CASE W/TP
ZB3 AS TOP ASSY S/P
60.ACZV7.001
CASE/COVER/BRACKET
ASSEMBLY
LOWER CASE W/SPEAKER
ZB3 BASE ASSY S/P
60.ACZV7.002
CASE/COVER/BRACKET
ASSEMBLY
HEATSINK COVER
ZB3 HS COVER ASSY S/P
60.ACZV7.003
DUMMY-NEW CARD
ZB1 CARDBUS DUMMY
CARD S/P
42.AA7V7.011
CPU/PROCESSOR
CPU INTEL YONAH CORE DUO FSB667 1.66G 2M SL8VR
ZC1 INTEL CPU YONAH
1.66G S/P
KC.23001.DTP
CPU/PROCESSOR
CPU INTEL YONAH CORE DUO FSB667 1.83G 2M SL8VQ
ZC1 INTEL CPU YONAH
1.83G S/P
KC.24001.DTP
CPU/PROCESSOR
CPU INTEL YONAH CORE DUO FSB667 2.0G 2M SL8VP
ZC1 INTEL CPU YONAH
2.0G S/P
KC.25001.DTP
CPU/PROCESSOR
CPU INTEL YONAH CORE DUO FSB667 2.16G 2M SL8VN
ZC1 INTEL CPU YONAH
2.16G S/P
KC.26001.DTP
CPU/PROCESSOR
CPU INTEL CELERON 1M 1.66G
SL8VZ
ZB3 YONAH 1.66G S/P
KC.N0001.420
CPU/PROCESSOR
CPU INTEL CELERON 1M 1.73G
SL92F
ZB3 YONAH 1.73G S/P
KC.N0001.430
CPU/PROCESSOR
DVD RW DRIVE
DVD RW DRIVE
DVD/CDRW COMBO MODULE 24X
ZB3 COMBO MODULE
6M.ACFV7.001
DVD RW DRIVE
"DVD COMBO,PHILIPS SCB5265
,GB,LF"
ZB2 COMBO
(SCB5265)FW:TX07 S/P
KO.02403.007
COMBO DRIVE
CDRW/DVD COMBO DRIVE 24X HLDS
GCC-4244N LF 1.00AB
ZB1 COMBO HLDS (GCC4244N) F/W:1.00 LF S/P
KO.0240A.005
DVD RW DRIVE
DVD/CDRW (COMBO) UJDA770AC-A
STN B/S
ZL7 DVD COMBO
UJDA770AC-A BS S/P
KO.02406.013
CASE/COVER/BRACKET
ASSEMBLY
"ODD HOLDER FIX
ZB1(EBZB1037,R3A)"
ZB1 ODD HOLDER FIX S/P
42.AA7V7.002
CASE/COVER/BRACKET
ASSEMBLY
ZB1 ODD BEZEL ASSY G/B COMBO
ZB1 ODD BEZEL ASSY G/
B S/P
42.AA7V7.005
DVD RW DRIVE
DVD SUPER MULTI MODULE
ZB3 SUPER MODULE
MODULE
6M.ACFV7.001
DVD RW DRIVE
DVD SUPER MULTI HLDS GMA-4082N
ZB2 DVD SUPER MULTI DL
GMA-4082N S/P
KU.0080D.021
DVD RW DRIVE
DVD SUPER MULTI PANASONIC UJ850BAA-A FW1.5
ZC1 DVD SUPERMUTI
PAN UJ850 S/P
KU.00807.025
DVD RW DRIVE
DVD SUPER MULTI PHILIPS SDVD8821 F/W:EX02 LF
ZB2 DVD SUPER
(SDVD8821)F/W:EX02 S/P
KU.00809.005
DVD RW DRIVE
DVD SUPER MULTI PIONEER DVRK16RS LF
ZB2 DVD
SUPERDRIVE(DL) DVRK16RS STNS/P
KU.00805.029
DVD RW DRIVE
DVD SUPER MULTI LITE-ON SSM8515S LF
ZB2 DVD(SUPER MULTI
)SSM-8515S S/P
KU.00804.022
Chapter 6
106
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
CASE/COVER/BRACKET
ASSEMBLY
ODD HOLDER FIX ZB1
ZB1 ODD HOLDER FIX S/P
42.AA7V7.002
CASE/COVER/BRACKET
ASSEMBLY
ZB1 ODD BEZEL ASSY G/B SUPER
MULTI
ZB1 ODD BEZEL ASSY G/
B SUPER MULTI S/P
42.AA7V7.007
DVD RW DRIVE
DVD SUPER MULTI PIONEER SLOTIN ASSY
ZB3 DVD SUPER MULT
PIO ASSY S/P
DVD RW DRIVE
DVD SUPERDRIVE DVR-K06RS
FW:1.01
ZB3 DVD SUPER MULTI
PIONEER SLOT-IN S/P
CASE/COVER/BRACKET
ASSEMBLY
OPTICAL DEVICE HOLDER
ZB1 ODD HOLDER FIX S/P 42.AA7V7.002
CASE/COVER/BRACKET
ASSEMBLY
ODD BEZEL ASSY
ZB3 SUPER MULTI BEZEL
ASSY S/P.
HDD/HARD DISK DRIVE
107
Chapter 6
CATEGORY
Chapter 6
PARTNAME
DESCRIPTION
PART NO.
HDD(40G) ST9402112A 9AH417-188
ZL6C HDD 40G SEAG LF
S/P
KH.04001.019
HDD(40G)HTS421240H9AT00
ZL5 HDD 40G
HTS421240H9AT00
HITACH S/P
KH.04007.013
60G HGST 2.5 4200RPM HAKONE-A
F/W :A70G
ZL6C HDD 60G HGST S/P
KH.06007.009
HDD(60G) ST960812A 9AH432-188
ZL6C HDD 60G SEAG LF
S/P
KH.06001.006
HDD(60G) ST96812A 9W3882-188
ZB1 HDD 60G ST96812A
SEAGATE S/P
KH.06001.007
HDD(60G)HTS541060G9AT00
ZL6 HDD 60GB HGST
HTS541060G9AT00 S/P
KH.06007.009
HDD(60GB)MK6034GAX-CZK
FW:AC101A
ZB2
HDD(60GB)MK6034GAXCZK S/P
KH.06004.007
"80G SEAGATE 2.5"" 4200RPM
ST980829A LF N2.2 FW:3.06"
ZL6C HDD 80G SEAG LF
S/P
KH.08001.021
80G HGST 2.5 4200RPM HAKONE-A
F/W:A70G
ZL6C HDD 80G HGST S/P
KH.08007.011
HDD(80G)HTS541080G9AT00
ZL3 80G HDD
HTS541080G9AT00 (HIT)
S/P
KH.08007.013
HDD(80GB)MP0804H FW:YS200-05
ZL6C HDD 80G SUMSUNG
LF S/P
KH.0800B.004
HDD(100G) ST9100825A 9AH439-188
ZL6C HDD 100G SEAG LF
S/P
KH.10001.006
HDD(100G) ST9100824A 9W3039-188
ZB1 HDD 100G
ST9100824A SEAGATE S/
P
KH.10001.007
HDD(100GB)MK1032GAX CZK
ZF3 HDD 100G
MK1032GAX CZK
TOSHIBA S/P
KH.10004.002
HDD(120G) ST9120824A 9AH434-188
ZL6C HDD 120G SEAG LF
S/P
KH.12001.023
HDD(120G)HTS421212H9AT00
0A26308
ZL6C HDD 120G HGST S/P KH.12007.006
HDD(120G) ST9120821A 9W3884-188
ZL6C HDD 120G SEAG
3.06 LF S/P
KH.12001.024
HDD(120G)MK1234GAX CZK
ZB3 HDD 120G
)MK1234GAX S/P
KH.12004.002
HDD BRACKET
ZB1 HDD BRACKET S/P
33.AA7V7.002
ZB1 HDD COVER ASSY
ZB1 HDD COVER ASSY S/
P
42.AA7V7.008
108
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
KEYBOAED
AS1680/AS1410 KEYBOARD DARFON
US International
ZL1C K/B NON ERGO-UI
S.P.
KB.A2707.001
AS1680/AS1410 KEYBOARD DARFON
Chinese
ZL1C K/B NON ERGOTAIWAN S.P.
KB.A2707.002
AS1680/AS1410 KEYBOARD DARFON
Spanish
ZL1C K/B NON ERGOSPANISH S.P.
KB.A2707.003
AS1680/AS1410 KEYBOARD DARFON
Thai
ZL1C K/B NON ERGO-THAI
S.P.
KB.A2707.004
AS1680/AS1410 KEYBOARD DARFON
Brazilian Protugese
ZL1C K/B NON ERGOBRAZ PROTU S.P.
KB.A2707.005
AS1680/AS1410 KEYBOARD DARFON
Korea
ZL1C K/B NON ERGOKOREA S.P.
KB.A2707.006
AS1680/AS1410 KEYBOARD DARFON
UK
ZL1C K/B NON ERGO-U.K
S.P.
KB.A2707.007
AS1680/AS1410 KEYBOARD DARFON
German
ZL1C K/B NON ERGOGERMAN S.P.
KB.A2707.008
AS1680/AS1410 KEYBOARD DARFON
Italian
ZL1C K/B NON ERGOITALIAN S.P.
KB.A2707.009
AS1680/AS1410 KEYBOARD DARFON
French
ZL1C K/B NON ERGOFRENCH S.P.
KB.A2707.010
AS1680/AS1410 KEYBOARD DARFON
Swiss/G
ZL1C K/B NON ERGOSWISS/G S.P.
KB.A2707.011
AS1680/AS1410 KEYBOARD DARFON
Portuguese
ZL1C K/B NON ERGOPORTUG S.P.
KB.A2707.012
AS1680/AS1410 KEYBOARD DARFON
Arabic
ZL1C K/B NON ERGOARABIC S.P.
KB.A2707.013
AS1680/AS1410 KEYBOARD DARFON
Belgium
ZL1C K/B NON ERGOBELGIUM S.P.
KB.A2707.014
AS1680/AS1410 KEYBOARD DARFON
Sweden
ZL1C K/B NON ERGOSWEDEN S.P.
KB.A2707.015
AS1680/AS1410 KEYBOARD DARFON
Czech
ZL1C K/B NON ERGOCZECH S.P.
KB.A2707.016
AS1680/AS1410 KEYBOARD DARFON
Hungaian
ZL1C K/B NON ERGOHUNG S.P.
KB.A2707.017
AS1680/AS1410 KEYBOARD DARFON
Norway
ZL1C K/B NON ERGONORWAY S.P.
KB.A2707.018
AS1680/AS1410 KEYBOARD DARFON
Danish
ZL1C K/B NON ERGODANISH S.P.
KB.A2707.019
AS1680/AS1410 KEYBOARD DARFON
Turkish
ZL1C K/B NON ERGOTURKISH S.P.
KB.A2707.020
AS1680/AS1410 KEYBOARD DARFON
Canadian French
ZL1C K/B NON ERGOCANA FREN S.P.
KB.A2707.021
AS1680/AS1410 KEYBOARD DARFON
Japanese
ZL1C K/B NON ERGOJAPAN S.P.
KB.A2707.022
AS1680/AS1410 KEYBOARD DARFON
Greek
ZL1C K/B NON ERGOGREEK S.P.
KB.A2707.023
AS1680/AS1410 KEYBOARD DARFON
Hebrew
ZL1C K/B NON ERGOHEBREW S.P.
KB.A2707.024
AS1680/AS1410 KEYBOARD DARFON
Russian
ZL1C K/B NON ERGORUSS S.P.
KB.A2707.025
LCD
109
Chapter 6
CATEGORY
DESCRIPTION
PART NO.
LCD MODULE 15.4 WXGAG 16MS
GLARE W/CCD-0.3M
ZB3 LCD 15.4 WXGAG AS
W/CCD-0.3M GF S/P
6M.ACZV7.003
LCD 15.4 IN. WXGAG QDI QD15TL0702 GLARE 16MS
ZL6C LCD QDI QD15TL0702 GLARE S/P
LK.15409.009
LCD 15.4 IN. WXGAG CMO N154I2L02 GLARE 16MS
"ZB2
LCD(TFT)15.4""N154I2L02(WXGA) S/P"
LK.1540D.012
LCD 15.4 IN. WXGAG AU B154EW02V1 GLARE 16MS
ZB3 LCD AUO B154EW02
GF S/P
LCD INVERTER BOARD
ZB1 INV MODULE S/P
19.AA7V7.001
CABLE
LCD CABLE ASSY - 15.4 IN. W/CCD
ZB3 LCD CABLE ASSY W/
CCD S/P
50.ACZV7.002
CASE/COVER/BRACKET
ASSEMBLY
"LCD COVER - 15.4 IN. W/ANTENNA
,CCD 0.3M"
"ZB2 AS 15.4"" LCD
COVER ASSY WCCD(0.3M) S/P"
60.AB1V7.003
CASE/COVER/BRACKET
ASSEMBLY
LCD BEZEL - 15.4 IN. FOR CCD N-UV
ZB3 15.4 LCD BEZEL
ASSY W-CCD N-UV S/P
60.TCFV7.005
LCD BRACKET W/HINGE 15.4 IN. - L
"ZB1 15.4"" HINGE-L ASSY
S/P"
33.AA7V7.003
LCD BRACKET W/HINGE 15.4 IN. - R
"ZB1 15.4"" HINGE-R ASSY
S/P"
33.AA7V7.004
LCD
LCD MODULE 15.4 WXGAG GLARE
W/ANTENNA
ZB3 LCD LP(15.4WXGA)
AS B/S GL S/P
TBD
LCD
LCD 15.4 IN. WXGA LPL LP154W01TLA2 GLARE
ZL8 LCD 15.4 LP154W01TLA2(WXGA)S/P
LK.15408.014
BOARD
LCD INVERTER BOARD
ZB1 INV MODULE S/P
19.AA7V7.001
CABLE
LCD CABLE - 15.4 IN.
ZB1 CABLE ASSY S/P
50.AA7V7.011
LCD COVER - 15.4 IN. W/ANTENNA
"ZB1 AS 15.4"" LCD
COVER ASSY S/P"
60.AA7V7.005
Chapter 6
PARTNAME
110
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
"ZL1 15.4""-WIDE LCD BEZEL ASSY"
ZB1 LCD BEZEL 15.4 S/P
60.TAJV7.006
CASE/COVER/BRACKET
ASSEMBLY
LCD BRACKET W/HINGE 15.4 IN. - L
"ZB1 15.4"" HINGE-L ASSY
S/P"
33.AA7V7.003
CASE/COVER/BRACKET
ASSEMBLY
LCD BRACKET W/HINGE 15.4 IN. - R
"ZB1 15.4"" HINGE-R ASSY
S/P"
33.AA7V7.004
LCD
LCD MODULE 15.4 WXGAG NONGLARE W/ANTENNA
ZB3 LCD
QDI(15.4WXGA)L07 AS B/S
S/P
TBD
LCD
LCD 15.4 IN. WXGAG QDI QD15TL0701 NON-GLARE
ZL6C LCD QDI QD15TL07- LK.15409.008
01 S/P
BOARD
LCD INVERTER BOARD
ZB1 INV MODULE S/P
19.AA7V7.001
LCD CABLE - 15.4 IN.
ZB1 CABLE ASSY S/P
50.AA7V7.011
CASE/COVER/BRACKET
ASSEMBLY
LCD COVER - 15.4 IN. W/ANTENNA
"ZB1 AS 15.4"" LCD
COVER ASSY S/P"
60.AA7V7.005
CASE/COVER/BRACKET
ASSEMBLY
"ZL1 15.4""-WIDE LCD BEZEL ASSY"
ZB1 LCD BEZEL 15.4 S/P
60.TAJV7.006
CASE/COVER/BRACKET
ASSEMBLY
LCD BRACKET W/HINGE 15.4 IN. - L
"ZB1 15.4"" HINGE-L ASSY
S/P"
33.AA7V7.003
CASE/COVER/BRACKET
ASSEMBLY
LCD BRACKET W/HINGE 15.4 IN. - R
"ZB1 15.4"" HINGE-R ASSY
S/P"
33.AA7V7.004
SO-DIMM DDRII533 256MB
NT256T64UH4A1FN-37B LF
ZB1 RAM DDRII5 256M
NANYA S/P
KN.25603.029
SO-DIMM DDRII533 256M
HYS64T32000HDL-3.7-A 32X64 LF
(0.11u)
ZB1 RAM DDRII5 256M INF
S/P
KN.25602.023
SO-DIMM DDRII533 256MB
M470T3354CZ3-CD5 LF (Pb-free)
ZB1 RAM DDRII533 256MB
SAMSUNG S/P
KN.2560B.017
MEMORY
SO-DIMM DDRII533 256MB
MT4HTF3264HY-53EB4 LF
KN.25604.030
SO-DIMM DDRII 533 256MB
HYMP532S64BP6-C4 LF
KN.2560G.012
SO-DIMM DDRII 533 512MB
HYS64T64020HDL-3.7-A LF (0.11u)
ZC1 INFINEON DDRII 533
512MB RAM S/P
KN.51202.021
SO-DIMM DDRII533 512MB
NT512T64UH8A1FN-37B LF
ZB1 RAM(512M)DDR2
NANYA S/P
KN.51203.023
SO-DIMM DDRII 533 512MB
HYMP564S64BP6-C4 LF (.09UM)
111
KN.5120G.013
Chapter 6
CATEGORY
PARTNAME
DESCRIPTION
PART NO.
SO-DIMM DDRII533 512MB
GU33512AGEPN612C
ZB2 RAM(512M)DDR2 S/P
KN.51209.005
SDIMM 512M SAMSUNG
M470T6554CZ3-CD5
ZB1 RAM DDRII533 512MB
SAMSUNG S/P
KN.5120B.015
SO-DIMM DDRII 533 512MB
HYMP564S64BP6-C4 LF
KN.5120G.013
SO-DIMM DDRII533 1GB
NT1GT64U8HA0BN-37B LF
ZC1 NANYA DDRII533 1GB
RAM S/P
KN.1GB03.006
SO-DIMM DDRII533 1GB
GU331G0AGEPN6E2C LF
ZC1 RAM 1GB DDR2
GU331G0AGEPN6E2C S/P
KN.1GB09.004
SO-DIMM DDRII533 1GB
M470T2953CZ3-CD5 LF
ZB3 RAM DDRII5 1G SUM
S/P
KN.1GB0B.004
MAINBOARD
MAINBOARD
MAINBOARD ATI RC410 UMA PATA W/ ZB3 MB ASSY(UMA)??? S/
READER W/O CPU MEMORY
P
MB.ACZ06.001
MAINBOARD
MAINBOARD ASSY(M52P/128MB)
ZB3 MB ASSY(M52P/
128MB) S/P
MAINBOARD
MAINBOARD ASSY(M52P/256MB)
ZB3 MB ASSY(M52P/
256MB) S/P
THERMAL MODULE
ZB3 THERMAL MODULE
ASSY S/P
60.ACZV7.004
MISCELLANEOUS
"NAMEPLATE
AS3660(FCZB3002,R3A)"
ZB3 NAMEPLATE S/P
40.ACZV7.001
MISCELLANEOUS
LCD RUBBER PAD-UP
ZL1A RUBBER PAD-UP
S.P.
47.AA7V7.002
MISCELLANEOUS
RUBBER FOOT - HEATSINK COVER
ZL1A RUBBER FOOT S.P.
47.T50V7.002
SPEAKER SET
ZB1 SPEAKER ASSY S/P
23.AA7V7.001
SCREW
SCWER M2.5*3.0-I(BNI)(NYLOK)EP
ZB1 SCWER M2.5*3.0I(BNI)(NYLOK)EP S/P
86.T25V7.012
SCREW
SCREW M2.5*6-I(BNI)(NYLOK)
ZB1 SCREW M2.5*6I(BNI)(NYLOK)S/P
86.A08V7.004
SCREW
SCREW M2.5*6.0-P(NI)(NYLOK)
ZB1 SCREW M2.5*6.0P(NI)(NYLOK)S/P
86.AA7V7.003
SCREW
SCREW M2.0X3.0-I-NI-NYLOK
ET2S SCREW MM2.0X3.0
SPARE PART
86.A03V7.012
SCREW
SCREW M2.5*5.0-I(NI)(NYLOK)
ZB1 SCREW M2.5*5.0I(NI)(NYLOK) S/P
86.T23V7.010
SCREW
SCREW M2.0*5-I(NI)(NYLOK)
ZB1 SCREW M2.0*5I(NI)(NYLOK) S/P
86.T23V7.006
SCREW
SCREW I3*3.5M-NIH(M3L3.5)
ET2S SCREW MM3.0X3.5
SPARE PART
86.A03V7.011
SCREW
SCREW I2*3M-NIHY (M2L3)
ZG1S I2*3M-NIHY (M2L3)
S/P
86.T25V7.008
HEATSINK
HEATSINK
MISCELLANEOUS
SPEAKER
SPEAKER
SCREW
Chapter 6
112