Technical information | Acer 3660 Laptop User Manual

Acer TravelMate 2300/4000/4500 Series
Service Guide
Service guide files and updates are available
on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on TravelMate 2300/4000/4500 service guide.
Date
II
Chapter
Updates
2004/10/13
Chapter 1
Specify core logic for TravelMate 2300 series
2005/01/07
Chapter 3
ODD module disassembling SOP
Copyright
Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.
Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
IV
SCREEN MESSAGES
Denotes actual messages that appear
on screen.
NOTE
Gives bits and pieces of additional
information related to the current
topic.
WARNING
Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION
Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT
Reminds you to do specific actions
relevant to the accomplishment of
procedures.
Preface
Before using this information and the product it supports, please read the following general information.
1.
This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2.
Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Performance
T
T
Intel® Pentium M® processor 705, 715, 725, 735, 745, 755 or Intel® Celeron M® processor
Intel® 855GME or 852GM chipset (manufacturing option; Intel® 855GME is for TM4000/4500 and
Intel® 852GM is for TM2300)
T
256/512 MB of DDR333 SDRAM standard, upgradeable to 2048 MB with dual soDimm modules
T
30 GB and above high-capacity, Enhanced-IDE hard disk
T
Advanced Configuration Power Interface (ACPI) power management system.
T
Internal removable optical drive (AcerMedia bay)
T
Li-ion main battery pack
T
The TFT LCD panel providing a lare viewing area for maximum efficiency and ease-of-use:
Display
t14.1”
XGA (1024x768) resolution
t15.0”
XGA (1024x768) or SXGA+ (1400x1050) resolution
t15.4”
WXGA (1200x800) or WSXGA+ (1680x1050) resolution
T
ATI MOBILITYTM RADEONTM 9700 with 64MB of video memory (manufacturing option)
T
3D graphics support
T
Simultaneous display on LCD and CRT monitor, and other display devices like projector support
T
“Automatic LCD dim” feature that automatically decides the best settings for your display and
conserves pwer
T
Dual indenpendent display
Multimedia
T
High-speed drive: DVD/CD-RW Combo, DVD-Dual or DVD-Super Multi
T
16-bit high-fidelity AC’97 stereo audio
T
Built-in microphone and dual speakers
T
Built-in microphone
T
High-speed DVD/CD-RW Combo, DVD-Dual or DVD-Super Multi drive
Connectivity
Chapter 1
T
Built-in 56Kbps fax/data modem
T
Integrated 10/100/1000 Mbps Fast Ethernet connection (manufacturing option)
T
Fast infrared wireless communication (manufacturing option)
T
Three Universal Serial Bus (USB) 2.0 ports
T
IEEE 1394 port
T
InvilinkTM 802.11b/g or LnviLinkTM 802.11a/b/g dual-band tri-mode Wireless LAN (manufacturing
option)
1
T
Bluetooth® (manufacturing option)
T
SD/MMC/MS memory card reader (manufacturing option; for TravelMate 4500 only)
T
100-pin port replicator connector (manufacturing option)
Human-centric design and ergonomics
T
Rugged, yet extremely portable design
T
Stylish appearance
T
Full-size keyboard with four programmable launch keys
T
Ergonomically-centered touchpad pointing device
T
Acer FineTouch keyboard with a 5-degree curve
T
Internet 4-way scroll button
Keyboard and Pointing Device
T
88/89-key Windows keyboard
T
Ergonomically-centered touchpad pointing device with scroll function
T
Acer FineTouchTM keyboard with a 5-degree curve
Expansion
T
One Type II CardBus PC Card slot
T
Upgradeable memory modules
T
Acer EasyPort (only in TravelMate 4500)
T
One Type II PC Card slot
T
One RJ-11 phone jack (V.92, 56Kbps modem)
T
One RJ-45 network jack
T
One DC-in jac (AC adapter)
T
One 100-pin port replicator connector (manufacturing option) for TravelMate 4500 only
T
One external monitor port
T
One speaker/headphone-out jack (3.5mm mini jack)
T
One audio line-in jack (3.5mm mini jack)
T
One microphone-in jack (3.5mm mini jack)
T
One Infrared (FIR) port (manufacturing option)
T
One IEEE 1394 port (manufacturing option)
T
One S-video TV-out port (manufacturing option)
T
Three USB 2.0 ports
T
3-in-1 (MS/MMC/SD) memory card reader (manufacturing option; for TravelMate 4500 only)
I/O Ports
2
Chapter 1
System Block Diagram
A
B
C
D
1
5V / 3.3V / 12V
Page : 10
2.5V / 1.25V / 1.8V
Page : 10
1.5V / 1.2V
Page : 10
CPU CORE
Page : 10
VGA CORE/VRAM
Page : 10
BATTERY
CHARGER
Page : 10
BATTERY
SELECT
Page : 10
1
5VPCU
3V_ALWAYS
+12V
+5V
3V_S5
5V_S5
3VSUS
5VSUS
2.5VSUS
+2.5V
+1.8V
MVREF_DM
SMDDR_VTERM
1.5V_S5
+1.5V
AGP_VCC (+1.5V)
1.2VCCT
VTT
VCC_CORE
VGA_CORE
LINE
IN
2
MIC IN
Page:13
2.5V_VGA
Page:13
2
Page : 10
CLOCK GEN
CYPRESS
CY28346-2
CLOCK S/S
ICS
*IC91718
Page : 10
3
AC97
4
Centrino
Page : 2 , 3
BANIAS DORTHAN
CELEROM-M
/
/
/
/
5
ATI
M11-P
64M /
128M
Page : 4 ~ 5
6
EXT_LVDS
EXT_CRT
EXT_TV-OUT
INT_LVDS
INT_CRT
7
SWITCH
CIRCUIT
TI
PCMCIA+1394
+3 IN 1
Page: 11
PCI7411
MINI-PCI
Wireless LAN
Modem/LAN
Page : 15
BROADCOM
1G LAN
5788M
Page:12
CRT
Page:17
Page:17
LVDS
TV-OUT
Page:17
BOTHHAND
TRANSFORMER
DOCKING 2
USB PORT
USB4
Page: 15
MINI-USB
SYSTEM 3
USB PORT
USB0,1
Page : 15
Sheet
8
3 IN 1
Page: 11
PCMCIA
Page: 11
1394
RJ45
35
Rev
A1A
Page:12
Page: 11
8
1
Acer Incorporated
Document Number
Friday, June 04, 2004
BLOCK DIAGRAM
of
PROJECT:Kestrel Series
USB2,3,5
Size
Date:
7
Page : 15
INT_TV-OUT
Page : 4 ~ 5
CHRONTEL
CH7011A
Page:16
DOCKING
Print Port
DEVICE
M11
BROADCOM LAN
MINI-PCI
TI 7411
6
Page:16
RGB
LVDS
AGP BUS
IrDA
5
INTE#,INTF#,INTG#
DOCKING
COM Port
DVO
PCI BUS
NS
USB 2.0
NS
Keyboard
AD18
AD20
AD23
AD22
Page : 18
SIO (87383)
Touchpad
Page:16
4
IDSEL
Page:16
GNT0#
GNT1#
GNT2#
GNT3#
INTERUPT
INTA#
INTD#
INTB# , INTC#
Page:15
Page : 18
KBC(97551)
LPC
Page : 6 ~ 7
421 BGA
82801DBM
ICH4-M
HUB I/F 66(266)MHz
Page : 4 ~ 5
732 Micro-FCBGA
Montara-GME
82855GME
HOST BUS 400MHz
INTEL Mobile_479 CPU
DOCKING
PS2
REQ0#
REQ1#
REQ2#
REQ3#
PCI ROUTING TABLE
Page:16
ATA 66/100
ATA 66/100
333MHZ DDR
CLK_SDRAM0~5,
CLK_SDRAM0~5#
DDR-SODIMM1
Page:8~9
Page:8~9
DDR-SODIMM2
IDE - HDD
Page:16
IDE-ODD
Page:16
MEDIA BAY
Page:16
AUDIO CODEC
Page:13
RJ11
MODEM
CONEXANT
20493-21
LINE
OUT
Page:13
Page:12
Page:14
CONEXANT
20468-31
Page:14
AMP
MAX9750
SPEKER
Page:13
3
A
B
C
D
3
Chapter 1
Board Layout
Top View
4
1
Keyboard Connector
7
3 in 1 Connector
2
Bluetooth Board Connector
8
Speaker Connector
3
LCD Cable Connector
9
Internal Microphone Connector
4
LED Board Connector
10
Modem Board Connector
5
Lid Switch
11
Touchpad Board Connector
6
Modem Cable Connector
Chapter 1
Bottom View
1
Power Jack
16
Audio Cable Connector
2
CRT
17
Line-in Connector
3
Docking
18
Headphone Out Connector
4
Audio Cable Connector
19
Microphone-in Connector
5
Main Battery Connector
20
USB Connector
6
ODD Connector
21
IEEE 1394 Connector
7
Media Bay Connector
22
PCMCIA
8
Mini PCI Slot
23
USB Connector
9
Second Battery Connector
24
CPU Socket
10
RTC Battery Connector
25
USB Connector
11
DDR DIMM Connector
26
S-Video
12
HDD Connector
27
RJ45 and RJ11 Connector
Chapter 1
5
13
6
IR
28
LAN Cable Connector
14
Bluetooth Switch
29
FAN Connector
15
Wireless Switch
30
LAN Cable Connector
Chapter 1
A TravelMate tour
After knowing your computer features, let us show you around your new TravelMate computer.
Front Open View
#
Icon
Item
Description
1
Display screen
Also called LCD (liquid-crystal display),
displays computer output.
2
Microphone
Internal microphone for sound recording.
3
Keyboard
Inputs data into your computer.
4
Palmrest
Comfortable support area for our hands
when you use the computer.
5
Click buttons (Left,
center and right)
The left and right buttons function like the
left and right mouse buttons; the center
button serves as a 4-way scroll button.
6
Touchpad
Touch-sensitive pointing device which
functions like a computer mouse.
Turns on the computer power.
Chapter 1
7
Status indicators
Light-Emitting Diodes (LEDs) that turn on
and off to show the status of the
computer’s function and components.
8
Launch keys
Buttons for launching frequently used
programs.
7
9
8
Power button
Turns the computer on and off.
Chapter 1
Front Closed View
#
Icon
Item
Description
1
Speakers
Left and right speakers deliver stereo audio
output.
2
Infrared port
Interfaces with infrared devices (e.g., infrared printer, IR-aware computer). The function is for TravelMate 4000 and TravelMate
4500.
3
Power indicator
Lights when the computer is on.
4
Battery indicator
Lights when the battery is being charged
5
Bluetooth®
communications
Indicates that (optional) Bluetooth is
enabled.
6
Wireless
communication
Indicates status of wireless LAN communication.
7
Line-in/Mic-in jack
Accepts audio line-in devices (e.g., audio
CD player, stereo walkman).
8
Line-in/MIc-in jack
Accepts audio line-in devices (e.g., audio
CD player, stereo walkman).
9
Speaker/Line-Out/
Headphone jack
Connects to audio line-out devices (e.g.,
speakers, headphones).
10
USB 2.0 port
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).
11
Latch
Locks and releases the lid.
Chapter 1
9
Left View
#
10
Icon
Item
Description
1
Optical drive
Internal optical drive; accepts CDs or DVDs
depending on the optical drive type.
2
LED indicator
Lights up when the optical drive is active.
3
Emergency eject hole
Ejects the optical drive tray when the
computer is turned off.
4
Optical drive eject
button
Ejects the optical drive tray from the drive.
5
AcerMedia bay
(Manufacturing option)
Houses an AcerMedia drive module.
Chapter 1
Right Panel
#
Icon
Item
Description
1
IEEE 1394 port
(Manufacturing option)
Connects to IEEE 1394 devices. The
function is for TravelMate 4000 and
TravelMate 4500 only.
2
PC Card slot eject
button
Ejects the PC Card from the slot.
3
PC Card slot
Connects to one Type II CardBus PC Card.
4
3-in-1 card reader
Accepts MS, MMC and SD card.
Note: The 3-in-1 card reader is a
manufacturing option, subject to
configuration. Only one card can operate at
any given time.
Chapter 1
5
Two USB 2.0 ports
Connects to Universal Serial Bus (USB) 2.0
devices (e.g., USB mouse, USB camera).
6
S-video port
Connects to a television or display device
with S-video input. This is for TravelMate
4000 and TravelMate 4500 only.
7
Network jack
Connect to an Ethernet 10/100-based
network.
8
Modem jack
Connects to a phone line.
9
Ventilation slots
Enable the computer to stay cool, even
after prolonged use.
11
Rear Panel
#
12
Icon
Item
Description
1
Power jace
Connects to an AC adapter.
2
External display port
Connects a display device (e.g., external
monitor, LCD projector).
3
100-pin port replicator
connector
(Manufacturing option)
Connects to an I/O port replicator, or Acer
EasyPort expansion devices.(for
TravelMate 4500 only)
4
Security keylock
Connects to a Kensington-compatible
computer security lock.
Chapter 1
Bottom Panel
#
1
Item
Cooling fan
Description
Helps keep the computer cool.
Note: Do not cover or obstruct the opening
of the fan.
Chapter 1
2
Battery lock
Locks the battery in place.
3
Memory compartment
Houses the computer’s main memory.
4
Hard disk bay
Houses the computer’s hard disk (secured
by a screw).
5
AcerMedia bay release
latch
Unlatches the AcerMedia drive for
removing the optical drive. (Only in
TravelMate 4500)
6
AcerMedia bay
Houses an AcerMedia drive module.
7
Battery release latch
Unlatches the battery to remove the battery
pack.
8
Battery bay
Houses the computer’s battery pack.
13
Indicators
The computer has three easy-to-read status icons on the upper-right above the keyboard.
Icon
14
Function
Description
Caps lock
Lights when Caps Lock is activated.
Num lock
Lights when Num Lock is activated.
Media Activity
Lights when the disc or AcerMedia is
activated.
Chapter 1
In addition, there are two indicators at the front panel. Even when the cover is closed, the state or features can
still be seen.
Icon
Chapter 1
Function
Description
Power
Lights when the computer is on.
Battery indicator
Lights when the battery is being charged.
15
Using the Keyboard
The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and
twelve function keys.
Lock Keys
The keyboard has three lock keys which you can toggle on and off.
16
Lock Key
Description
Caps Lock
When Caps Lock is on, all alphabetic characters typed
are in uppercase.
Num lock
(Fn-F11)
When Num Lock is on, the embedded keypad is in
numeric mode. The keys function as a calculator
(complete with the arithmetic operators +, -, *, and /).
Use this mode when you need to do a lot of numeric
data entry. A better solution would be to connect an
external keypad.
Scroll lock
(Fn-F12)
When Scroll Lock is on, the screen moves one line up
or down when you press w and y respectively.
Scroll Lock does not work with some applications.
Chapter 1
Embedded Numeric Keypad
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired Access
Num Lock On
Num Lock Off
Number keys on embedded
keypad
Type numbers in a normal
manner.
Cursor-control keys on
embedded keypad
Hold j while using
cursor-control keys.
Hold Fn while using cursorcontrol keys.
Main keyboard keys
Hold Fn while typing letters
on embedded keypad.
Type the letters in a normal
manner.
Chapter 1
17
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key
Windows key
Icon
Description
Pressed alone, this key has the same effect as
clicking on the Windows Start button; it launches the
Start menu. It can also be used with other keys to
provide a variety of function:
+ Tab (Activates next taskbar button)
+ E (Explores My Computer)
+ F1 (Opens Help and Support)
+ F (Opens the Find: All Files dialog box
+ M (Minimizes all windows)
j+
+ M (Undoes the minimize all windows)
+ R (Displays the Run... dialog box)
Application
key
18
This key has the same effect as clicking the right
mouse button; it opens the application’s context
menu.
Chapter 1
Hot Keys
The computer employs hot keys or key combinations to access most of the computer’s controls like sreen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination.
Hot Key
Icon
Function
Description
Fn-F1
Hot key help
Displays help on hot keys.
Fn-F2
Acer eSetting
Launches the Acer eSetting in the Acer eManager set
by the Acer Empowering key.
Fn-F3
Acer
ePowerManagement
Launches the Acer ePowerManagement in the Acer
eManager set by the Acer Empowering key.
Fn-F4
Sleep
Puts the computer in Sleep mode.
Fn-F5
Display toggle
Switches display output between the display screen,
external monitor (if connected) and both the display
screen and external monitor.
Fn-F6
Screen blank
Turns the display screen backlight off to save power.
Press any key to return.
Fn-F7
Touchpad toggle
Turns the internal touchpad on and off.
Fn-F8
Speaker toggle
Turns the speakers on and off.
Fn-w
Volume up
Increases the speaker volume.
Chapter 1
19
Hot Key
Function
Description
Fn-y
Volume down
Decreases the speaker volume.
Fn-x
Brightness up
Increases the screen brightness.
Fn-z
Brightness down
Decreases the screen brightness
US dollar
Types the US dollar sign.
Euro
Types the Euro symbol.
Alt Gr-$
Alt Gr-Euro
20
Icon
Chapter 1
Special Key
You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard.
To type:
The Euro symbol
1.
Open a text editor or word processor.
2.
Either directly press the Euro symbol at the bottom-right of the keyboard, or hold Alt Gr and then press
the Euro symbol at the upper-center of the keyboard.
The US dollar sign
1.
Open a text editor or word processor.
2.
Either directly press the dollar sign at the bottom-right of the keyboard, or hold Alt Gr and then press the
dollar sign at the upper-center of the keyboard.
NOTE: This function varies by the operating system version.
Chapter 1
21
Launch Keys
Located at the upper-right above the keyboard are four buttons. These buttons are called launch keys. They
are designated as the mail, Web browser, Empowering and programmable keys.
Press the Acer Empowering Key to run the Acer EManager. The mail and Web browser are default for Email
and Internet programs, but can be reset by users. To set the mail, Web browser and programmable keys, run
the acer Launch Manager.
Launch Key
22
Default application
Mail
Email application (user-programmable)
Web browser
Internet browser application (user
programmable)
e
Acer eManager application (userprogrammable)
P
User-programmable
Chapter 1
In addition, there are two launch keys at the front panel. Even when the cover is closed, you can easily access
the features of Wireless and Bluetooth®. However, the Wireless and Bluetooth keys cannot be set by users.
Description
Default application
communications
Lights to indicate the status of Bluetooth
(optional) communications.
Wireless
communications
Lights to indicate the status of wireless LAN
(optional) communications.
Bluetooth®
Chapter 1
23
Touchpad
The built-in touchpad is a PS/2-compatible pointing device that senses movement on its surface. This means
the cursor responds as you move your finger on the surface of the touchpad. The central location on the
palmrest provides optimum comfort and support.
NOTE: If you are using an external USB or serial mouse, you can press Fn-F7 to disable the touchpad.
Touchpad Basics
The following teaches you how to use the touchpad:
T
Move your finger across the touchpad to move the cursor.
T
Press the left (1) and right (3) buttons located on the edge of the touchpad to do selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the touchpad produces similar results.
T
Use the 4-way scroll (2) button (top/bottom/left/and right) to scroll.
Function
Right Button
Scroll Button
Tap
Execute
Click twice
quickly
Tap twice (at the same
speed as double-clicking
the mouse button)
Select
Click once
Tap once
Drag
Click and hold,
then use finger
to drag the
cursor on the
touchpad
Tap twice (at the same
speed as double-clicking
a mouse button) then hold
finger to the touchpad on
the second tap to drag the
cursor
Access context
menu
24
Left Button
Click once
Chapter 1
Function
Scroll
Left Button
Right Button
Scroll Button
Tap
Click and hold
the button in the
desired
direction (up/
down/left/right)
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The
touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response.
Tapping too hard will not increase the touchpad’s responsiveness.
Chapter 1
25
Hardware Specifications and Configurations
Processor
Item
CPU type
Specification
®
Intel Celeron M processor at 1.3GHz~1.4GHZ for TravelMate 2300
Intel® Pentium M processor at 1.5GHz~1.6GHz (Dothan) for TravelMate
4000
Intel® Pentium M processor at 1.8GHz (Dothan) for TravelMate 4500
Core logic
InteI® 855GME+ICH4 for TravelMate 4000/4500
Intel® 852GM+ICH4 for TravelMate 2300
CPU package
Intel socketable 478pin Micro-BGA
CPU core voltage
1.308V (highest frequency mode) to 0.956V (low frequency mode)
0.748V (deeper sleep mode)
BIOS
Item
Specification
BIOS vendor
Phneoix
BIOS Version
3A03
BIOS ROM type
SST 39SF040A, 512KX8 CMOS Boot Block Flash Memory
BIOS ROM size
512KB
BIOS package
32-pin PLCC
Supported protocols
ACPI 1.0b, PC Card 95, SM BIOS 2.3, IEEE1284-ECP/EPP, PCI 2.2, PnP
1.0a, DMI 2.0, PS/2 keyboard and mouse, USB 2.0, VGA BIOS, CD-ROM
bootable, IEEE 1394
BIOS password control
Set by setup manual
Second Level Cache
Item
Specification
Cache controller
Built-in CPU
Cache size
512K for Intel® Celeron M processor at 1.3~1.4GHz-TravelMate 2300
2MB for Intel® Pentium M processor at 1.5~1.6GHz (Dothan)-TravelMate
4000
2MB for Intel® Pentium M processor at 1.8GHz (Dothan)-TravelMate 4500
1st level cache control
Always enabled
2st level cache control
Always enabled
Cache scheme control
Fixed in write-back
System Memory
Item
Memory controller
Specification
®
Intel 855GME built-in (TravelMate 4000/4500);
Intel® 852GM built-in (TravelMate 2300)
Memory size
26
0MB (no on-board memory)
DIMM socket number
2 sockets
Supports memory size per socket
1024MB
Supports maximum memory size
2G (by two 1024MB SO-DIMM module)
Supports DIMM type
DDR Synchronous DRAM
Supports DIMM Speed
333 MHz
Supports DIMM voltage
2.5V and 1.25V
Chapter 1
System Memory
Item
Specification
Supports DIMM package
200-pin soDIMM
Memory module combinations
You can install memory modules in any combinations as long as they
match the above specifications.
Memory Combinations
Slot 1
Slot 2
Total Memory
0MB
128MB
128MB
0MB
256MB
256MB
0MB
512MB
512MB
0MB
1024MB
1024MB
128MB
128MB
256MB
128MB
256MB
384MB
128MB
512MB
640MB
1284MB
1024MB
1152MB
256MB
128MB
384MB
256MB
256MB
512MB
256MB
512MB
768MB
256MB
1024MB
1280MB
512MB
128MB
640MB
512MB
256MB
768MB
512MB
512MB
1024MB
512MB
1024MB
1536MB
1024MB
0MB
1024MB
1024MB
128MB
1125MB
1024MB
256MB
1280MB
1024MB
512MB
1536MB
1024MB
1024MB
2048MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
LAN Interface
Item
Specification
Chipset
Broadcom BCM4401 (10/100M) ; BroadCom BCM5788M (1G)BroadCom BCM5788M chipset is manufacturing option
Supports LAN protocol
10/100/1000Mbps
LAN connector type
RJ45
LAN connector location
Right panel
Features
Integrated 10/100 BASE-T transceiver
Wake on LAN support compliant with ACPI 2.0
PCI v2.2
IR Interface
Item
Specification
Part name
VISHAY TFU6102F
Package
8-pin SMT type
Chapter 1
27
IR Interface
Item
Specification
Performance
4Mbit/s
Compliant
IrDA 1.1
Modem Interface
Item
Specification
Data modem data baud rate (bps)
56K
Supports modem protocol
V.90/V.92
Modem connector type
RJ11
Modem connector location
Right panel
Bluetooth Interface
Item
Chipset
Specification
Broadcom BCM2035
Data throughput
723 bps (full speed data rate)
Protocol
Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG
specification is ratified).
Interface
USB 1.1
Connector type
Mini-USB
Wireless Module 802.11b/g (optional device)
Item
Specification
Chipset
Intel
Data throughput
11~54 Mbps
Protocol
802.11b+g
Interface
Mini-PCI type II
®
Wireless Module 802.11a/b/g (optional device)
Item
Specification
Chipset
Intel
Data throughput
11~54 Mbps
Protocol
802.11 a+b+g
Interface
Mini-PCI type II
®
3-in-1 card reader
Item
28
Specification
Chipset
TI PC7411
Protocol
support Smart Media, Multi-Media Card and Security Digital
Chapter 1
Hard Disk Drive Interface
Item
Specification
Vendor &
Model Name
HGST
HTS424030M9AT00/
Toshiba Pluto
MK3025GAS/
HGST
HTS424040M9AT00/
Toshiba Pluto
MK4025GAS/
HGST MORAGA
IC25N060ATMR04-0
Toshiba Pluto
MK6025GAS
HGST MORAGA
IC25N080ATMR04-0
Toshiba Pluto
MK8025GAS
Capacity (MB)
30000
40000
60000
80000
Bytes per
sector
512
512
512
512
Data heads
2
2
3/4 (for Toshiba)
4
Disks
1
1
2
2
Spindle speed
(RPM)
4200 RPM
4200 RPM
4200 RPM
4200 RPM
2048KB
8192KB
8192KB
Drive Format
Performance Specifications
Buffer size
2048KB/
Interface
ATA/ATAPI-6; ATA-6
ATA/ATAPI-6; ATA-6
ATA/ATAPI-6; ATA-6
ATA/ATA-6; ATA-6
Max. media
transfer rate
(disk-buffer,
Mbytes/s)
372
372
350
350
Data transfer
rate
(host~buffer,
Mbytes/s)
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
100 MB/Sec.
Ultra DMA mode-5
5V(DC) +/- 5%
5V(DC) +/- 5%
5V(DC) +/- 5%
DC Power Requirements
Voltage
tolerance
5V(DC) +/- 5%
Combo Drive Interface
Item
Specification
Vendor & model name
DVD/CDRW KME UIDA760 (24x24x8x24x)
DVD/CDRW QSI SBW-242C (24x24x8x24x)
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (KB/sec)
Sustained:
Max 3.6Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Buffer Memory
2MB
Interface
Enhanced IDE(ATAPI) compatible
Applicable disc format
DVD: DVD-ROM, (DVD-5, DVD-9, DVD-10, DVD-18),DVD-R (read, single
border), DVD-RW, DVD-RAM (2.6GB, 4.7GB)
CD: CD-DA, CD-ROM, CD-ROM XA, CD-R, CD-RW Photo (Multisession)
Video CD, CD-Extra, (CD+), CD-test
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
Chapter 1
5 V +/- 5 % (Operating)
29
DVD-Dual Interface
Item
Specification
Vendor & model name
DVD Dual HLDS GWA-4040N
Performance Specification
With CD Diskette
With DVD Diskette
Transfer rate (KB/sec)
Sustained:
Max 3.6Mbytes/sec
Sustained:
Max 10.8Mbytes/sec
Buffer Memory
2MB
Interface
Enhanced IDE(ATAPI) compatible
Applicable disc format
Support disc formats
1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD, CD-Extra and
CD-Text
2. Reads data in Photo CD (single and Multi-session)
3. Reads standard CD-DA
4. Reads and writes CD-R discs
5. Reads and writes CD-RW discs
6. Reads and writes in each dVD+R/RW (Ver. 1.1)
7. Reads data in each DVD-ROM and DVD-R (Ver. 2.0 for Authoring)
8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVD-RW and
DVD+R/RW (Ver1.1)
Loading mechanism
Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage
5 V +/- 5 % (Operating)
Audio Interface
Item
Specification
Audio Controller
Conexant CX20468-31
Audio onboard or optional
Built-in
Mono or Stereo
Stereo
Resolution
18 bit stereo digital to analog converter
18 bit stereo analog to digital converter
Compatibility
AC97
Mixed sound source
Line-in, CD
Voice channel
8/16-bit, mono/stereo
Sampling rate
44,1 KHz (48K byte for AC97 interface)
Internal microphone
Yes
Internal speaker / Quantity
Yes/2
Audio Jack
Item
Number of audio jack
30
Specification
Internal: 2
External:3
Rated input
1W
Connector type
Internal: two 1W speakers
External: Headphone out, microphone in and line-in
Chapter 1
Video Interface
Item
Specification
Chipset
ATI Mobility RADEON 9700 (optional for TM4000/4500)
Package
MBGA 708 pin
Interface
AGP8X
Supports ZV (Zoomed Video) port
Yes
Video Memory
Item
Specification
Chipset
TM4000 and TM4500 has two types of PCBAs. One is with Intel
855GME and the other is ATI M11 (ATI Mobility RADEON 9700)
TM2300 Intel 852GM integrated
Memory size
UMA 16/32/64MB for TM2300
UMA 16/32/64MB or ATI M11-P 64MB for TM4000
UMA 16/32/64MB or ATI M11-P 64MB for TM4500
Interface
DDR
USB Port
Item
Specification
Chipset
ICH4-M
USB Compliancy Level
2.0
OHCI
USB 1.1 and USB 2.0 Host controller
Number of USB port
3
Location
two on the right side; one on the front side
Serial port function control
Enable/Disable by BIOS Setup
IEEE 1394 Port
Item
Specification
Chipset
TI PC7411
Number of IEEE 1394 port
1
Location
Right side
Connector type
IEEE 1394
PCMCIA Port
Item
Specification
PCMCIA controller
TI PC7411
Supports card type
Type-II
Number of slots
One type-II
Access location
Right panel
Supports ZV (Zoomed Video) port
No ZV support
Supports 32 bit CardBus
Yes
Chapter 1
31
System Board Major Chips
Item
Core logic
Controller
®
Intel 855GME+ICH4 (TravelMate 4000/4500)
Intel® 852GM+ICH4 (TravelMate 2300)
VGA
ATI Mobility RADEON 9700 (optional for TravelMate 4000/4500)
LAN
BroadCom BCM4401 (10/100M); BCM5788M(1G)
IEEE 1394
TI PC7411
USB 2.0
ICH4-M
Super I/O controller
NS 87383
MODEM
Conexant RD01-D620
Bluetooth
Broadcom BCM2035
Wireless 802.11 b
Intel®
Wireless 802.11 b+g
Intel®
PCMCIA
TI PC7411
Audio
Conexant CX20468-31
3-in-1 card reader
TI PC7411
Keyboard
Item
Specification
Keyboard controller
NS PC97551
Total number of keypads
88-/89-key
Windows logo key
Yes
Internal & external keyboard work
simultaneously
1. Plug USB keyboard to the USB port directly: Yes
2. Use port replicator then plug a USB/PS 2 keyboard to the USB
port/PS 2 port on the port replicator: Yes
Battery
Item
Specification
Vendor & model name
Sanyo 4UR18650F-2-QC140
Panasonic CGR-B/8B5AE
Simplo 916-3020
Battery Type
Li-ion
Pack capacity
4400 mAh
Number of battery cell
8
Package configuration
4 cells in series, 2 series in parallel
Normal voltage
14.4V
Charge voltage
16.8+-0.2v
LCD 14.1 inch
Item
Vendor & model name
32
Specification
AU B141XG05
CMO N141XB-L01
QDI QD141XLH12
Screen Diagonal (mm)
357(14.1inch)
14inch
360(14.1inch)
Active Area (mm)
285.7(H)x214.3(V)
285.7(H)x214.3(V)
285.7(H)x214.3(V)
Display resolution (pixels)
XGA (1024x768)
XGA (1024x768)
XGA (1024x768)
Chapter 1
LCD 14.1 inch
Item
Specification
Pixel Pitch
0.279(H)x0.279(H)
mm
0.279(H)x0.279(H)
mm
0.279(H)x0.279(H)
mm
Pixel Arrangement
RGB vertical stripe
RGB vertical stripe
RGB vertical stripe
Display Mode
Normally white
Normally white
Normally white
Typical White Luminance (cd/m2)
150
130(min)/160(typ)
120
1.2(5 points)
1.5(13 points)
not show
Contrast Ratio
250 (min)/ 300 (typ)
300(min)/450(typ)
300(min)
Response Time (Optical Rise Time/Fall
Time)msec
15/10
6/17(typ)
10/25(max)
12.5/22.5
Nominal Input Voltage VDD
+3.3V
not show
+3.3V
Typical Power Consumption (watt)
5.3
4.03 (for backlight
unit)
N/A
Weight
400g (w/o inverter)
420g
460g
Physical Size(mm)
299(W)x228(H)x5.5
(D)
299(W)x228(H)x5.2
(D)
299(W)x228(H)x6.2
(D)
Electrical Interface
R/G/B Data, 3Sync,
Signals, Clock (4
pairs LVDS)
1 channel LVDS
1 channel LVDS
Support Color
Native 262K colours
262K colours
262K colours
45/45
15/35
45/45
15/35
40/40
10/30
0 to +50
-20 to +60
0 to +50
-20 to +60
0 to +50
-25 to +60
AU:
QDI
Hannstar
B150XG01
QD15XL06-01
HSD150PX14-A07
also called Brightness
Luminance Uniformity
1.45(5 points)
2(13 points)
Viewing Angle (degree)
Horizontal: Right/Left
Vertial: Upper/Lower
Temperature Range( ° C)
Operating
Storage (shipping)
LCD 15 inch
Item
Specification
Vendor & model name
Screen Diagonal (mm)
381
15.0 inches
15.0 inches
Active Area (mm)
304.1x228.1
304.1x228.1
304.1x228.1
Display resolution (pixels)
1024x768 XGA
1024x768 XGA
1024x768 XGA
Pixel Pitch
0.297x0.297
0.099x0.297
0.297x0.297
Pixel Arrangement
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
Display Mode
2
Typical White Luminance (cd/m )
also called Brightness
Normally White
Normally White
Normally White
180 (5 point
average)
160
150
150 (5 point
average)
Luminance Uniformity
N/A
N/A
70
Contrast Ratio
300
300
250
Response Time (Optical Rise Time/Fall
Time)msec
24/11
8/17
10/25
Nominal Input Voltage VDD
+3.3V Typ.
+3.3V
3.3V
Chapter 1
15/35
33
LCD 15 inch
Item
Specification
Typical Power Consumption (watt)
5.6/5.7
3.96
N/A
Weight
550
570
600
Physical Size(mm)
317.3x242.0x6.0
317.3x242.0x5.9
317.3x242.0x6.5
Electrical Interface
1 channel LVDS
1 channel LVDS
1 channel LVDS
Support Color
262K colors (RGB
6-bit data driver)
262,144
262,144
Horizontal: Right/Left
40/40
45/45
40/40
Vertial: Upper/Lower
10/30
15/35
20/40
0 to +50
0 to +50
0 to +50
-20 to +60
-25 to +60
-20 to +60
SAMSUNG
LTN150XB-L03
Hitachi
LCD 15.4" WXGA
QDI
15.0 inches, 381
390.1
304.1x228.1
304.1x228.1
331.2x207.0
Viewing Angle (degree)
Temperature Range( ° C)
Operating
Storage (shipping)
LCD 15 inch and 15.4 inch
Item
Vendor & model name
Specification
Screen Diagonal (mm)
Active Area (mm)
TX38D81VC1CAB
Display resolution (pixels)
1024x768 XGA
1024x768 XGA
1280x800 WXGA
Pixel Pitch
0.297x0.297
0.297x0.297
0.2588x0.2588
Pixel Arrangement
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
R.G.B. Vertical
Stripe
Display Mode
Normally White
Transmissive &
normally White
Normally White
Typical White Luminance (cd/m2)
160
170
185
Luminance Uniformity
N/A
40
1.4 (5pts)
Contrast Ratio
200
200
400
Response Time (Optical Rise Time/Fall
Time)msec
10/30(typ)
30/30
5/20
also called Brightness
Nominal Input Voltage VDD
+3.3V
+3.3V
+3.3V Typ.
Typical Power Consumption (watt)
4.6 for backlight unit
only
N/A
4.38
Weight
585
580
585
Physical Size(mm)
317.3x242.1x6.0
317.3x242.1x6.0
344x222.0x6.35
max
Electrical Interface
1 channel LVDS
1 channel LVDS
1 channel LVDS
Support Color
262K
262K
262K colors (RGB
6-bit data driver)
Horizontal: Right/Left
45/45
40/40
15/35
Vertial: Upper/Lower
25/45
20/40
45/45
Temperature Range( ° C)
N/A
0 to +40
0 to +50
-20 to +60
-25 to +60
Viewing Angle (degree)
Operating
Storage (shipping)
34
Chapter 1
LCD Inverter
Item
Specification
Vendor & model name
SUMIDA TWS-449-147
Brightness conditions
Vadj=3.3V
Input voltage (V)
8~20
Input current (mA)
350 (max)
Output voltage (V, rms)
1600 (no load)
Output current (mA, rms)
5.6~5.4
Output voltage frequency (k Hz)
55~58K Hz
AC Adaptor
Item
Specification
Input rating
90V AC to 264V AC, 47Hz to 63Hz
Maximum input AC current
1.7A
Inrush current
220A@115VAC
220A@230VAC
Efficiency
82% min. @115VAC input full load
System Power Management
ACPI mode
Power Management
Mech. Off (G3)
All devices in the system are turned off completely.
Soft Off (G2/S5)
OS initiated shutdown. All devices in the system are turned off
completely.
Working (G0/S0)
Individual devices such as the CPU and hard disc may be power
managed in this state.
Suspend to RAM (S3)
CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4)
Also called Hibernate state. System saves all system states and
data onto the disc prior to power off the whole system.
Chapter 1
35
36
Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press m during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press m to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
PhoenixBIOS Setup Utility
. Info.
Main
Advanced
Security
Boot
CPU Type:
CPU Speed:
Intel (R) Pentium (R) M processor 1.70Ghz
1700 MHz
HDD1 Model Name:
HDD1 Serial Number:
HDD2 Model Name:
HDD2 Serial Number:
ATAPI Device:
System BIOS Ver:
VGA BIOS Ver:
KBC Ver:
Serial Number
IC25N080ATMR04-0
MPAA01Q2G0746A
Asset Tag Number:
Product
1234567890
Aspire1680
Manufacturer Name:
UUID:
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1
Help
Esc Exit
Chapter 2
↑ ↓
←→
Exit
MATSHITADVD-RAM UJ-825S
3A01
Montara-GME3360
PQ1A24
1234567890123456789012
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
37
Navigating the BIOS Utility
There are six menu options: Info., Main, System Devices, Security, Boot, and Exit.
Follow these instructions:
T
To choose a menu, use the cursor left/right keys (zx).
T
To choose a parameter, use the cursor up/down keys ( wy).
T
To change the value of a parameter, press por q.
T
A plus sign (+) indicates the item has sub-items. Press e to expand this item.
T
Press ^ while you are in any of the menu options to go to the Exit menu.
T
In any menu, you can load default settings by pressing t. You can also press u to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information vary in models.
38
Chapter 2
Information
PhoenixBIOS Setup Utility
. Info.
Main
Advanced
Security
Boot
CPU Type:
CPU Speed:
Intel (R) Pentium (R) M processor 1.70Ghz
1700 MHz
HDD1 Model Name:
HDD1 Serial Number:
HDD2 Model Name:
HDD2 Serial Number:
ATAPI Device:
System BIOS Ver:
VGA BIOS Ver:
KBC Ver:
Serial Number
IC25N080ATMR04-0
MPAA01Q2G0746A
Asset Tag Number:
Product
1234567890
Aspire1680
Manufacturer Name:
UUID:
Acer
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
F1
Help
Esc Exit
↑ ↓
←→
Exit
MATSHITADVD-RAM UJ-825S
3A01
Montara-GME3360
PQ1A24
1234567890123456789012
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter
Description
Floppy Disk Drive
Shows floppy drive type informaiton only when this model has floppy disk drive.
HDD Model Name
This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number
This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name
This field displays the mofel name of devices installed on secondary IDE master. The hard
disk drive or optical drive model name is automatically detected by the system.
ATAPI Serial Number
This field shows the serial number of devices installed on secondary IDE master.
Serial Number
This field displays the serial number of this unit.
UUID Number
This will be visible only when an internal LAN device is presenting.
UUID=32bytes
Chapter 2
39
Main
The Main screen displays a summary of your computer hardware information, and also includes basic setup
parameters. It allows the user to specify standard IBM PC AT system parameters.
PhoenixBIOS Setup Utility
Info.
Advanced
Main
Security
Boot
Exit
Item Specific Help
System Time:
[05:34:07]
System Date:
[07/23/2004]
System Memory:
640 KB
<Tab>, <Shift-Tab>, or
<Enter> selects field.
Shows system base memory size
Extended Memory:
238MB
Shows extended memory size
Video Memory
[16MB]
VGA memory size
Quiet Boot:
[Enabled]
Power on Display:
Network boot:
F12 Boot Menu:
[Auto ]
[Enabled]
[Disabled]
D2D recovery:
[Enabled]
F1
Help
Esc Exit
↑↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
40
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Format/Option
System Time
Sets the system time. The hours are displayed
with 24-hour format.
Format: HH:MM:SS
(hour:minute:second) System Time
System Date
Sets the system date.
Format MM/DD/YYYY (month/day/
year)
System Date
System Memory
This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory
This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory
Shows the VGA memory size. VGA Memory
size=64/128MB
Fast Boot
Determines if Customer Logo will be displayed or
not; shows Summary Screen is disabled or
enabled.
Option: Enabled or Disabled
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Power on display
Auto: During power process, the system will
detect if any display device is connected on
external video port. If any external display device
is connected, the power on display will be in CRT
(or projector) only mode. Otherwise it will be in
LCD only mode.
Option: Auto or Both
Both: Simultaneously enable both the integrated
LCD screen and the system’s external video port
(for an external CRT or projector).
LCD Auto Dim
Determines if the system will automatically dim
the LCD brightness in order to save power when
AC is not present.
Option: Enabled or Disabled
The system will support an automatic dimming of
the LCD backlight when the AC power is NOT
available (running on battery power).
Network Boot
Enables, disables the system boot from LAN
(remote server).
Option: Enabled or Disabled
F12 Boot Menu
Enables, disables Boot Menu during POST.
Option: Disabled or Enabled
D2D Recovery
Enables, disables D2D Recovery function. The
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
Option: Enabled or Disabled
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2
41
Advanced
The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced
settings of the system.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
Internal Touchpad:
[Both]
Infrared Port (FIR):
[Enabled]
Configure Infrared Port
using options:
[Disable]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when controlled
by OS
F1
Help
Esc Exit
↑ ↓
← →
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub- Menu
F10 Save and Exit
The table below describes the parameters in the screen. Settings in boldface are the default and suggested
parameter settings.
.
Parameter
Options
Enables, disables or auto detects the infrared port.
Disabled/Disabled/Auto
Parallel Port
Enables, disables or auto detects the parallel port.
Enabled/Disabled/Auto
Mode
Sets the operation mode of the parallel port.
ECP, EPP, Output only or Bidirectional
Base I/O address
Sets the I/O address of the parallel port.
378/278
Interrupt
Sets the interrupt request of the parallel port.
IRQ7/IRQ5
DMA channel
Sets a DMA channel for the printer to operate in
ECP mode. This parameter is enabled only if Mode
is set to ECP.
DMA3/DMA1
Infrared Port
42
Description
Chapter 2
Parameter
Description
Options
Legacy USB Support
Enables, disables USB interface devices support.
(Enable for use with a non-USB aware Operating
System such as DOS or UNIX).
Option: Disabled or Enabled
Hard Disk Recovery
Enables or disables Hard Disk to Hard Disk system
Recovery by pressing Fn+F10 key during POST.
Option: Disabled or Enabled
Chapter 2
43
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.
Info.
Main
PhoenixBIOS Setup Utility
Security
Advanced
Boot
Exit
Item Specific Help
Supervisor Password Is:
Clear
User Password Is:
Clear
Primary HardDisk Security:
HDD Master ID:
Clear
Set Supervisor Password
Set User Passord
Set HDD Password
[Enter]
[Enter]
Password on Boot
[Disabled]
43883445
[Enter]
When shown as [Locked],
the hard drive password
currently can not be changed
or disabled.
To change or disable it, turn
off the system and enter Setup
immediately after turning it
back on.
Press [Enter] to input, change,
or disable hard drive
passwords.
F1
Help
Esc Exit
44
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter
Description
Option
User Password is
Shows the setting of the user password.
Clear or Set
Supervisor Password is
Shows the setting of the Supervisor password
Clear or Set
Set User Password
Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set Supervisor Password
Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
Primary Harddisk Security
This feature is available to user when
Supervisor password is set. Password can be
written on HDD only when Supervisor
password or user password is set and
password on HDD is set to enabled.
Supervisor Password is written to HDD only
when Supervisor password is being set. User
password is written to HDD when both
passwords are set. When both Supervisor and
user password are present, both passwords
can unlock the HDD.
Disabled or Enabled
Password on Boot
Defines whether a password is required or not
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
Disabled or Enabled
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1.
Use the w andy keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2.
Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
Chapter 2
45
3.
4.
Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
If desired, you can opt to enable the Password on boot parameter.
5.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Press e twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4.
When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
46
1.
Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Password box appears:
2.
Type the current password in the Enter Current Password field and press e.
3.
Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4.
Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5.
If desired, you can enable the Password on boot parameter.
6.
When you are done, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2
47
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Boot
Exit
Item Specific Help
CD-ROM/DVD Drive
+ and - indicate device
categories. Use <Enter> to
expand/collapses.
Floppy Devices
+Hard Drive
Network Boot
Boot order is top-down using
only the top device in each
category.
Use <F6> and <F5> to move
highlighted item up and down.
F1
Help
Esc Exit
48
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
Chapter 2
Exit
The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use.
PhoenixBIOS Setup Utility
Info.
Main
Advanced
Security
Exit
Boot
Item Specific Help
Exit Saving Changes
Exit System Setup and save
your changes to CMOS.
Exit Dicarding Changes
Load Setup Defaults
Discard Changes
Save Changes
F1
Help
Esc Exit
↑ ↓
←→
Select Item
F5/F6 Change Values
F9 Setup Defaults
Select Menu
Enter Select 4 Sub-Menu
F10 Save and Exit
The table below describes the parameters in this screen.
Parameter
Exit Saving Changes
Description
Exit System Setup and save your changes to CMOS.
Exit Discarding Changes
Exit utility without saving setup data to CMOS.
Load Setup Default
Load default values for all SETUP item.
Discard Changes
Load previous values from CMOS for all SETUP items.
Save Changes
Save Setup Data to CMOS.
Chapter 2
49
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
T
New versions of system programs
T
New features or options
T
Restore a BIOS when it becomes corrupted.
Use the Phlash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Phlash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
NOTE: Please use the AC adaptor power supply when you run the Phlash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Phlash.
50
1.
Prepare a bootable diskette.
2.
Copy the Phlash utilities to the bootable diskette.
3.
Then boot the system from the bootable diskette. The Phlash utility has auto-execution function.
Chapter 2
Chapter 3
Machine Disassembly and Replacement
This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
To disassemble the computer, you need the following tools:
T
Wrist grounding strap and conductive mat for preventing electrostatic discharge
T
Small Philips screw driver
T
Philips screwdriver
T
Plastic flat head screw driver
Tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
When you remove the stripe cover, please be careful not to scrape the cover.
T
Chapter 3
51
General Information
Before You Begin
Before proceeding with the disassembly procedure, make sure that you do the following:
1.
Turn off the power to the system and all peripherals.
2.
Unplug the AC adapter and all power and signal cables from the system.
3. Remove the battery pack.
NOTE: The screws used to secure bottom case and upper case are more than one type. Please group same
type of screw together as you disassemble the system for service purpose. The image below is for your
reference. Please pay attention to the explanation below.
Battery
IO Bezel
The screws that secure heatsink cover, MIni PCI cover and HDD cover are with the covers. There is no need
to worry about mix them up. However, please notice that you have to group the screws on the following
locations together. There are twenty screws holding the bottom case to upper case but some screws are inside
the system. You may have to remove the HDD, the heatsink cover to see these screws. Mini PCI cover here
also called RAM/Wireless cover.
Screw Type
M2.5*6
(Part number: 86.T23V7.010)
52
Location
Bottom case and IO bezel
(hightlight with yellow circle)
Quantity
14
Chapter 3
Screw Type
M2.5*6
(Part number: 86.T23V7.010)
M2.5*6
(Part number: 86.T23V7.010)
M2.5*6
(Part number: 86.T23V7.010)
M2.5*3
(Part number: 86.T25V7.012)
M2.5*3
(Part number: 86.T25V7.012)
Chapter 3
Location
Quantity
Remove the IO bezel then
you will see.
2
Remove the heatsink cover
then you will see.
1
Remove the HDD cover then
you will see.
1
Detach the HDD module
then you will see.
1
Remove the battery then you
will see.
1
53
Disassembly Procedure Flowchart
The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence
and instructs you on the components that need to be removed during servicing. For example, if you want to
remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in
that order.
Start
Battery
*2
*2
E*2
RAM/Wireless
Cover
HDD Cover
IO Bezel
ODD Module
*2 back side
*4 left/right side
*2
Heatsink
Cover
HDD Module
Wireless LAN
Card
Memory
ODD
Connector
Board
ODD Holder
special screw for thermal*3
Ex1
Thermal
Module
CPU
ODD Drive
E*3
Middle Cover
B*2
Keyboard
*4
(right and left hinges)
LCD Module
B*2
Switch Board
B*5
E*16+B*2
Lower and
Upper Case
Assembly
Lower Case
Assembly
Upper Case
Assembly
Touchpad
E*2
*2 screw nuts
VGA Heatsink
54
*3
Main Board
3-in-1 Cover
*4
Speaker Set
B*2
Modem Board
B*2
Touchpad
Bracket
Bluetooth
Module
Touchpad
Board
Chapter 3
LCD Module
4 screw pads
M*4
LCD Bezel
*6 hinges
*2 brackets
LCD Inverter
Antenna set
LCD Cover
LCD
Assembly
*4
LCD
LCD Cable
LCD Brackets
Screw List
Item
Description
A
SCREW M2.0X3.0-I-NI-NYLOK
B
SCREW I2.5*3M-BNIH(M2.5L3)
C
SCREW M2.5*4L-BZN-NYLOK
D
SCREW M2.0X5-I-NI-NYLOK
E
SCREW MM25060IL69
F
SCREW M2.0*5-I(NI)(NYLOK)
G
SCREW M2.0X2.5-I-NI-NYLOK
H
SCREW I2*3M-NIHY (M2L3)
I
SCREW M1.7*3.0-I (BK)
J
SCREW I3*3.5M-NIH(M3L3.5)
Chapter 3
55
Removing the Battery Pack
56
1.
Unlock the battery lock.
2.
Slide the battery latch as shown then remove the battery pack.
Chapter 3
Removing the HDD Module/the Memory and the Wireless LAN Card/the
Thermal Module and the CPU/ODD Module and LCD Module
Removing the HDD Module
1.
Remove the two screws holding the HDD cover.
2.
Remove the HDD cover.
3.
Detach the HDD module then remove it.
Removing the Memory and the Wireless LAN Card
1.
Remove the two screws that secure the RAM/Wireless cover.
2.
Remove the RAM/Wireless cover.
3.
Pop up the memory then remove it.
4.
Disconnect the auxiliary and the main wireless antennae.
5.
Pop the wireless LAN card then remove it.
.
Removing the Thermal Module and CPU
1.
Remove the two screws holding the IO bezel.
2.
Then remove the IO bezel.
3.
Remove the two screws that secure the heatsink cover.
Chapter 3
57
4.
Remove the heatsink cover from the main unit.
5.
Disconnect the fan cable.
6.
Remove the four screws that secure the thermal module.
7.
Pull the thermal module outwards then remove it.
NOTE: The edge of the thermal module as shown is very sharp. Be very careful as you remove the thermal
module.
58
8.
Use a flat-bladed screwdriver to release the CPU lock.
9.
Remove the CPU from the socket carefully.
Chapter 3
Removing the ODD Module
1.
Remove the three screws holding the middle cover.
2.
Detach the middle cover carefully.
3.
Turn over the keyboard as shown.
4.
Disconnect the keyboard cable from the main board then remove the keyboard.
5.
Remove the screw that fastens the ODD module.
6. Turn over the notebook computer then detach the ODD module carefully.
NOTE: When you reattach the ODD, please make sure you attach the ODD module completely to the main
unit. Otherwise, you can not fasten the screw and the screw may damage the main board.
.
Removing the LCD Module
1.
Remove the three screws holding the keyboard cover.
2.
Open the LCD module as the picture shown then detach the keyboard cover from the main unit.
Chapter 3
59
.
3.
Remove the two screws that secure the keyboard as shown.
4.
Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard.
5.
Pull out the antenna set with a tweezers then take out the antenna set from the main unit.
6.
Disconnect the LCD coaxial cable.
7.
Remove the four screws holding the right and the left hinge. Two on each side.
8.
Then detach the LCD module from the main unit.
.
.
60
Chapter 3
Disassembling the Main Unit
Separate the Main Unit Into the Upper and the Lower Case Assembly
1.
Remove the two screws holding the switch board.
2.
Remove the switch board.
3.
Disconnect the touchpad FFC from the main board.
4.
Disconnect the bluetooth cable.
5.
Remove the five screws that secure the upper case.
6.
Remove the eighteen screws on the bottom as shown.
7.
Detach the upper case assembly and place it next to the lower case assembly.
8.
Disconnect the microphone cable then remove the upper case assembly.
Disassembling the Upper Case Assembly
1.
Disconnect the touchpad board to touchpad FFC.
2.
Disconnect the touchpad board to main board FFC.
3.
Then detach the touchpad board to main board FFC from the touchpad board.
Chapter 3
61
4.
Remove the three screws that secure the touchpad board.
5.
Remove the touchpad board from the upper case.
6.
Disconnect the touchpad board to touchpad FFC.
7.
Remove the touchpad board to touchpad FFC from the uppwer case assembly.
8.
Remove the four screws holding the touchpad bracket.
9.
Detach the touchpad bracket from the upper case assembly.
10. Remove the touchpad from the upper case.
11. Remove the two screws that secure the bluetooth module.
12. Disconnect the bluetooth module then remove it.
Disassembling the Lower Case Assembly
62
Chapter 3
1.
Disconnect the MDC cable from the modem board.
2.
Detach the MDC cable from the main board.
3.
Remove the two screws holding the modem board.
4.
Remove the modem board from the lower case.
5.
Disconnect the speaker cable from the main board.
6.
Remove the two screws that secure the main board.
7.
Remove the two screw nuts as shown.
8.
The you can detach the main board from the upper case.
9.
Remove the three screws that secure the VGA heatsink.
10. Remove the VGA heatsink from the main board as shown.
11. Remove the three in one cover from the lower case.
12. Remove the two screws that secure the speaker set on one side.
13. Then remove another two screws holding the speaker set on the other side.
14. Then take out the speaker set from the lower case.
Chapter 3
63
64
Chapter 3
Disassembling the LCD Module
1.
Remove the four screw caps as shown.
2.
Remove the four screws holding the LCD bezel.
3.
Then detach the LCD bezel from the LCD module.
4.
Disconnect the inverter board then remove it.
5.
Remove the three screws holding the right hinge.
6.
Then remove the three screws that secure the left hinge.
7.
Remove one screw that secure the LCD bracket.
8.
Remove another screw holding the LCD bracket on the other side.
9.
Then detach the LCD panel from the LCD cover carefully.
.
10. Remove the two screws holding the right bracket.
11. Then remove the right bracket.
12. Remove another two screws that tighten the left bracket.
Chapter 3
65
13. Remove the left bracket as the picture shows.
14. Tear off the tape fastening the LCD cable.
15. Tear off the the LCD cable fastening the LCD cable, then remove it..
66
Chapter 3
Disassembling the External Modules
Disassembling the HDD Module
1.
Remove the two screws holding the HDD bracket on one side.
2.
Remove another two screws holding the HDD bracket on the other side.
3.
Then take the hard disc drive out from the HDD bracket.
Disassembling the Optical Drive Module
1.
Remove the four screws as the picture shows.
2.
Remove the two screws that secure the optical disc drive and the ODD holder.
3.
Push the ODD holder as shown.
4.
Detach the ODD holder.
5.
Disconnect the ODD connector board then remove it.
Chapter 3
67
68
Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test this model. Non-Acer products, prototype cards, or modified
options can give false errors and invalid system responses.
1.
Duplicate symptom and obtain the failing symptoms in as much detail as possible.
2.
Distinguish symptom. Verify the symptoms by attempting to re-create the failure by running the diagnostic
test or by repeating the same operation.
3.
Disassemble and assemble the unit without any power sources.
4.
If any problem occurs, you can perform visual inspection before you fellow this chapter’s instructions. You
can check the following:
power cords are properly connected and secured;
there are no obvious shorts or opens;
there are no obviously burned or heated components;
all components appear normal.
5.
Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified)
Go To
Power failure. (The power indicator does not go
on or stay on.)
“Power System Check” on page 71.
POST does not complete. No beep or error
codes are indicated.
“Power-On Self-Test (POST) Error Message” on
page 73
“Undetermined Problems” on page 85
POST detects an error and displayed messages
on screen.
“Error Message List” on page 74
Other symptoms (i.e. LCD display problems or
others).
“Power-On Self-Test (POST) Error Message” on
page 73
Symptoms cannot be re-created (intermittent
problems).
Use the customer-reported symptoms and go to
“Power-On Self-Test (POST) Error Message” on
page 73
“Intermittent Problems” on page 84
“Undetermined Problems” on page 85
Chapter 4
69
System Check Procedures
External Diskette Drive Check
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1.
Reconnect the external diskette drive/DVD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
External CD-ROM Drive Check
Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1.
Boot from the diagnostics diskette and start the diagnostics program.
2.
See if CD-ROM Test is passed when the program runs to CD-ROM Test.
3.
Follow the instructions in the message window.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1.
Reconnect the external diskette drive/CD-ROM module.
2.
Replace the external diskette drive/CD-ROM module.
3.
Replace the main board.
Keyboard or Auxiliary Input Device Check
Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
Reconnect the keyboard cables.
2.
Replace the keyboard.
3.
Replace the main board.
The following auxiliary input devices are supported by this computer:
T
Numeric keypad
T
External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1.
Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board.
2.
Go to the diagnostic memory in the test items.
3.
Press F2 in the test items.
4. Follow the instructions in the message window.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
70
Chapter 4
Power System Check
To verify the symptom of the problem, power on the computer using each of the following power sources:
1.
Remove the battery pack.
2.
Connect the power adapter and check that power is supplied.
3.
Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
T
Chapter 4
“Check the Battery Pack” on page 72
71
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1.
Check out the Power Management in control Panel
2.
In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3.
Repeat the steps 1 and 2, for both battery and adapter.
4.
This helps you identify first the problem is on recharging or discharging.
From Hardware:
1.
Power off the computer.
2.
Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground). See the
following figure
3.
If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1.
After rebooting, run Tracking Pad PS2 Mode Driver. For example, run Syn touch driver.
2.
Run utility with the PS/2 mouse function and check if the mouse is working.
3.
If the the PS/2 mouse does not work, then check if the main board to switch board FPC is connected O.K.
4.
If the main board to switch board FPC is connected well, then check if the FCC on touch pad PCB
connects properly.
5.
If the FFC on touch pad PCB connects properly, then check if LS851 JP1 Pin6=5V are pulese. If yes, then
replace switch board. If no, then go to next step.
6.
Replace touch pad PCB.
7.
If the touch pad still does not work, then replace FPC on Track Pad PCB.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
72
Chapter 4
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 85.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
Chapter 4
73
Index of Error Messages
Error Message List
Error Messages
FRU/Action in Sequence
Struck Key
See “Keyboard or Auxiliary Input Device Check” on page 70
System CMOS checksum bad - Default
configuration used
RTC battery
Real time clock error
Run BIOS Setup Utility to reconfigure system, then reboot system.
RTC battery
Run BIOS Setup Utility to reconfigure system time, then reboot
system.
Main board
Previous boot incomplete - Default configuration
used
“Load Default Settings” in BIOS Setup Utility.
RTC battery
Main baord
Invalid System Configuration Data
“Load Default Settings” in BIOS Setup Utility.
Main board
Operating system not found
Enter Setup and see if fixed disk and drive A are properly identified.
Dikette drive
Hard disk drive
Main board
74
Chapter 4
Error Message List
No beep Error Messages
Power-on indicator turns off and LCD is blank.
FRU/Action in Sequence
Power source (battery pack and power adapter.) See “Power
System Check” on page 71
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
Main board.
Power-on indicator turns on and LCD is blank.
Power source (battery pack and power adapter.) See “Power
System Check” on page 71
Reconnect the LCD connector
Hard disk drive
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and LCD is blank.
But you can see POST on an external CRT.
Reconnect the LCD connectors.
LCD cable
LCD inverter
LCD
Main board
Power-on indicator turns on and a blinking cursor
shown on LCD during POST.
Chapter 4
Ensure every connector is connected tightly and correctly.
Main board
75
Phoenix BIOS Beep Codes
Code
Beeps
Verify Real Mode
03h
Disable Non-Maskable Interrupt (NMI)
04h
Get CPU type
06h
Initialize system hardware
08h
Initialize chipset with initial POST values
09h
Set IN POST flag
0Ah
Initialize CPU registers
0Bh
Enable CPU cache
0Ch
Initialize caches to initial POST values
0Eh
Initialize I/O component
0Fh
Initialize the local bus IDE
10h
Initialize Power Management
11h
Load alternate registers with initial POST
values
12h
Restore CPU control word during warm boot
13h
Initialize PCI Bus Mastering devices
14h
Initialize keyboard controller
16h
1-2-2-3
17h
BIOS ROM checksum
Initialize cache before memory autosize
18h
8254 timer initialization
1Ah
8237 DMA controller initialization
1Ch
Reset Programmable Interrupt Controller
20h
1-3-1-1
22h
1-3-1-3
Test DRAM refresh
Test 8742 Keyboard Controller
24h
Set ES segment register to 4 GB
26h
Enable A20 line
28h
Autosize DRAM
29h
Initialize POST Memory Manager
2Ah
Clear 215 KB base RAM
2Ch
1-3-4-1
RAM failure on address line xxxx
2Eh
1-3-4-3
RAM failure on data bits xxxx of low byte of
memory bus
2Fh
30h
Enable cache before system BIOS shadow
1-4-1-1
RAM failure on data bits xxxx of high byte of
memory bus
32h
Test CPU bus-clock frequency
33h
Initialize Phoenix Dispatch Manager
36h
Warm start shut down
38h
Shadow system BIOS ROM
3Ah
Autosize cache
3Ch
Advanced configuration of chipset registers
3Dh
Load alternate registers with CMOS values
42h
Initialize interrupt vectors
45h
46h
76
POST Routine Description
02h
POST device initialization
2-1-2-3
Check ROM copyright notice
Chapter 4
Code
Beeps
POST Routine Description
48h
Check video configuration against CMOS
49h
Initialize PCI bus and devices
4Ah
Initialize all video adapters in system
4Bh
QuietBoot start (optional)
4Ch
Shadow video BIOS ROM
4Eh
Display BIOS copyright notice
50h
Display CPU type and speed
51h
Initialize EISA board
52h
Test keyboard
54h
Set key click if enabled
58h
59h
2-2-3-1
Test for unexpected interrupts
Initialize POST display service
5Ah
Display prompt “Press F2 to enter SETUP”
5Bh
Disable CPU cache
5Ch
Test RAM between 512 and 640 KB
60h
Test extended memory
62h
Test extended memory address lines
64h
Jump to User Patch1
66h
Configure advanced cache registers
67h
Initialize Multi Processor APIC
68h
Enable external and CPU caches
69h
Setup System Management Mode (SMM) area
6Ah
Display external L2 cache size
6Bh
Load custom defaults (optional)
6Ch
Display shadow-area message
6Eh
Display possible high address for UMB
recovery
70h
Display error messages
72h
Check for configuration errors
76h
Check for keyboard errors
7Ch
Set up hardware interrupt vectors
7Eh
Initialize coprocessor if present
80h
Disable onboard Super I/O ports and IRQs
81h
Late POST device initialization
82h
Detect and install external RS232 ports
83h
Configure non-MCD IDE controllers
84h
Detect and install external parallel ports
85h
Initialize PC-compatible PnP ISA devices
86h
Re-initialize onboard I/O ports
87h
Configure Motherboard Configurable Devices
(optional)
88h
Initialize BIOS Area
89h
Enable Non-Maskable Interrupts (NMIs)
8Ah
Initialize Extended BIOS Data Area
8Bh
Test and initialize PS/2 mouse
8Ch
Initialize floppy controller
Chapter 4
77
Code
Beeps
8Fh
Determine number of ATA drives (optional)
90h
Initialize hard-disk controllers
91h
Initialize local-bus hard-disk controllers
92h
Jump to UserPatch2
93h
Build MPTABLE for multi-processor boards
95h
Install CD ROM for boot
96h
Clear huge ES segment register
97h
Fixup Multi Processor table
98h
1-2
Search for option ROMs. One long, two short
beeps on checksum failure.
99h
Check for SMART drive (optional)
9Ah
Shadow option ROMs
9Ch
Set up Power Management
9Dh
Initialize security engine (optional)
9Eh
Enable hardware interrupts
9Fh
Determine number of ATA and SCSI drives
A0h
Set time of day
A2h
Check key lock
A4h
Initialize Typematic rate
A8h
Erase F2 prompt
AAh
Scan for F2 key stroke
ACh
Enter SETUP
AEh
Clear Boot flag
B0h
Check for errors
B2h
B4h
78
POST Routine Description
POST done- prepare to boot operating system
1
One short beep before boot
B5h
Terminate QuietBoot (optional)
B6h
Check password (optional)
B9h
Prepare Boot
BAh
Initialize DMI parameters
BBh
Initialize PnP Option ROMs
BCh
Clear parity checkers
BDh
Display MultiBoot menu
BEh
Clear screen (optional)
BFh
Check virus and backup reminders
C0h
Try to boot with INT 19
C1h
Initialize POST Error Manager (PEM)
C2h
Initialize error logging
C3h
Initialize error display function
C4h
Initialize system error handler
C5h
PnPnd dual CMOS (optional)
C6h
Initialize notebook docking (optional)
C7h
Initialize notebook docking late
C8h
Force check (optional)
C9h
Extended checksum (optional)
D2h
Unknown interrupt
Chapter 4
Code
Beeps
POST Routine Description
E0h
Initialize the chipset
E1h
Initialize the bridge
E2h
Initialize the CPU
E3h
Initialize the system timer
E4h
Initialize system I/O
E5h
Check force recovery boot
E6h
Checksum BIOS ROM
E7h
Go to BIOS
E8h
Set Huge Segment
E9h
Initialize Multi Processor
EAh
Initialize OEM special code
EBh
Initialize PIC and DMA
ECh
Initialize Memory type
EDh
Initialize Memory size
EEh
Shadow Boot Block
EFh
System memory test
F0h
Initialize interrupt vectors
F1h
Initialize Run Time Clock
F2h
Initialize video
F3h
Initialize System Management Mode
F4h
1
Output one beep before boot
F5h
Boot to Mini DOS
F6h
Clear Huge Segment
F7h
Boot to Full DOS
Chapter 4
79
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error
LCD backlight doesn't work
Action in Sequence
First, plug a monitor to CRT port. Next, enter BIOS utility to running
“Load Default Settings” then reboot the system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
LCD is too dark
LCD brightness cannot be adjusted
Enter BIOS Utility to execute “Load Setup Default Settings”, then
reboot system.
Reconnect the LCD connectors.
Keyboard (if the brightness function key doesn't work).
LCD cable
LCD inverter
LCD
Main board
Unreadable LCD screen
Reconnect the LCD cable
Missing pels in characters
LCD cable
Abnormal screen
LCD
Wrong color displayed
Main board
LCD has extra horizontal or vertical lines
displayed.
Indicator-Related Symptoms
Symptom / Error
Action in Sequence
Indicator incorrectly remains off or on, but system
runs correctly
Main board
HDD/CD-ROM active indicators cannot work
HDD/CD-ROM drive
Device driver
Main board
Power-Related Symptoms
Symptom / Error
Power shuts down during operation
Action in Sequence
Power source (battery pack and power adapter). See “Power
System Check” on page 71.
Battery pack
AC adapter
See if the thermal module is overheat (Heat sink or fan).
Main board
The system cannot power-on.
Power source (battery pack and power adapter). See “Power
System Check” on page 71.
Battery pack
Power adapter
CPU
Main board
The system cannot power-off.
In Windows XP operating system, hold and press the power switch
for more than 4 seconds. If the system can power off, then the main
board is OK. Verify OS in the HDD.
Main board
80
Chapter 4
Power-Related Symptoms
Symptom / Error
Battery can’t be charged or discharged
Action in Sequence
See “Check the Battery Pack” on page 72.
Battery pack
Main board
System hang during POST
ODD/HDD/FDD/RAM module
Main board
PCMCIA-Related Symptoms
Symptom / Error
System cannot detect the PC Card (PCMCIA)
Action in Sequence
PCMCIA slot assembly
Main board
PCMCIA slot pin is damaged.
PCMCIA slot assembly
PC Card cannot be inserted or ejected
Check if the PCMCIA slot is blocked
Main board
Memory-Related Symptoms
Symptom / Error
Memory count (size) appears different from
actual size.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot system.
RAM module
Main board
Check BIOS revision
System can power on, but you hear two long
beeps: “B--, B--” and the LCD is blank.
Reinsert DIMM
DIMM
Main board
Speaker-Related Symptoms
Symptom / Error
In Windows, multimedia programs, no sound
comes from the computer.
Action in Sequence
OS volume control
Audio driver
Speaker
Main board
Internal speakers make noise or emit no sound.
Speaker
Main board
Microphone cannot work
Audio driver
Volume control in Windows XP
Main board
Power Management-Related Symptoms
Symptom / Error
The system will not enter hibernation mode
Action in Sequence
Power option in Windows XP
Hard disk drive
Main board
The system doesn’t enter standby mode after
closing the lid of the portable computer.
Driver of Power Option Properties
Lid close switch in upper case
Main board
Chapter 4
81
Power Management-Related Symptoms
Symptom / Error
The system doesn't resume from hibernation/
standby mode.
Action in Sequence
Connect AC adapter then check if the system resumes from
Standby/Hibernation mode.
Check if the battery is low.
Hard disk drive
Main board
The system doesn't resume from standby mode
after opening the lid of the portable computer.
LCD cover switch
Battery fuel gauge in Windows doesn’t go higher
than 90%.
Refresh battery (continue use battery until power off, then charge
battery).
Main board
Battery pack
Main board
System hangs intermittently.
Reconnect hard disk/CD-ROM drives.
Main board
Peripheral-Related Symptoms
Symptom / Error
System configuration does not match the
installed devices.
Action in Sequence
Enter BIOS Setup Utility to execute “Load Setup defaults”, then
reboot system.
Reconnect hard disk/CD-ROM drives/FDD or other peripherals.
Main board
External display does not work correctly.
Press Fn+F5, LCD/CRT/Both display switching
Keyboard
Main board
USB does not work correctly
Main board
Print problems.
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Run printer self-test.
Printer driver
Printer cable
Printer
Main board
Parallel port device problems
Enter BIOS Setup Utility to execute “Load Default Settings” then
reboot the system.
Device driver
Device cable
Device
Main board
Keyboard/Touchpad-Related Symptoms
Symptom / Error
Keyboard (one or more keys) does not work.
Action in Sequence
Reconnect the keyboard cable.
Keyboard
Main board
Touchpad does not work.
Reconnect touchpad cable.
Touchpad board
Main board
82
Chapter 4
Modem/LAN-Related Symptoms
Symptom / Error
Internal modem does not work correctly.
Action in Sequence
Phone cable
Driver
Reconnect the Internal modem cable to the main board tightly.
Main board
Internal LAN does not work correctly
Lan cable
Driver
Main board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 85.
Chapter 4
83
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
84
1.
Run the diagnostic test for the system board in loop mode at least 10 times.
2.
If no error is detected, do not replace any FRU.
3.
If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 71):
1.
Power-off the computer.
2.
Visually check them for damage. If any problems are found, replace the FRU.
3.
Remove or disconnect all of the following devices:
T
Non-Acer devices
T
Printer, mouse, and other external devices
T
Battery pack
T
Hard disk drive
T
DIMM
T
PC Cards
4.
Power-on the computer.
5.
Determine if the problem has changed.
6.
If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7.
If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
Chapter 4
T
System board
T
LCD assembly
85
Use NAPP CD to Build Master Hard Disc Drive
CD to Disk Recovery
86
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Put NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.
NAPP CD will start to preload the system, please click [Y].
5.
Select CD to Disk Revocery.
Chapter 4
6.
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below.
Chapter 4
87
88
7.
Then insert the System CD to the optical drive.
8.
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 4
Disk to Disk Recovery
1.
Prepare NAPP CD, Recovery CD and System CD.
2.
Put NAPP CD into the optical drive. Then boot up the system.
3.
The system will ask you if you want to build NAPP Master HDD. Please press any key to continue.
4.
NAPP CD will start to preload the system, please click [Y].
Chapter 4
89
5. Select Disk to Disk Recovery. Then choose Single Language or Multi-Languages Recovery.
NOTE: For Multi-Languages Recovery, not more than five languages could be loaded to the system.
6.
90
Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have
to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till
you finish all Recovery CDs.
Chapter 4
After you place the Recovery CD to the optical drive, you will see the display below.
7.
Then insert the System CD to the optical drive.
Chapter 4
91
8.
92
You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 4
Chapter 5
Jumper and Connector Locations
Top View
1
Keyboard Connector
CN5
7
3 in 1 Connector
CN10
2
Bluetooth Board Connector
CN6
8
Speaker Connector
CN12
3
LCD Cable Connector
CN2
9
Internal Microphone Connector
CN11
4
LED Board Connector
CN3
10
Modem Board Connector
CN9
Chapter 5
93
94
5
Lid Switch
SW2
6
Modem Cable Connector
CN4
11
Touchpad Board Connector
CN8
Chapter 5
Bottom View
1
Power Jack
CN13
16
Audio Cable Connector
CN34
2
CRT
CN14
17
Line-in Connector
CN39
3
Docking
CN15
18
Headphone Out Connector
CN37
4
Audio Cable Connector
CN16
19
Microphone-in Connector
CN38
5
Main Battery Connector
CN18
20
USB Connector
CN36
6
ODD Connector
CN19
21
IEEE 1394 Connector
CN35
7
Media Bay Connector
CN23
22
PCMCIA
CN30
8
Mini PCI Slot
CN24
23
USB Connector
CN28
9
Second Battery Connector
CN26
24
CPU Socket
U41
10
RTC Battery Connector
CN31
25
USB Connector
CN27
11
DDR DIMM Connector
CN32
26
S-Video
CN25
12
HDD Connector
CN33
27
RJ45 and RJ11 Connector
CN22
13
IR
U53
28
LAN Cable Connector
CN21
Chapter 5
95
96
14
Bluetooth Switch
SW4
29
FAN Connector
CN20
15
Wireless Switch
SW3
30
LAN Cable Connector
CN17
Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List
This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of TravelMate 4000/
4500 series products. Refer to this chapter whenever ordering for parts to repair or for RMA (Return
Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available
on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on
the printed Service Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a
DIFFERENT part number code from those given in the FRU list of this printed Service Guide. You MUST use
the local FRU list provided by your regional Acer office to order FRU parts for repair and service of customer
machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or
regulations on how to dispose it properly, or follow the rules set by your regional Acer office on how to
return it.
Chapter 6
97
Exploded Diagram
98
Chapter 6
TravelMate 4000
Picture
No.
Partname And Description
Part Number
Adapter
N/S
ADAPTER 65W 3 PIN DELTA SADP-65KB BF
19V
TBD
N/S
ADAPTER 65W 3 PIN LITE-ON PA-1650-02
QA 19V
TBD
N/S
ADAPTER 65W 3 PIN LI-SHIN SLS0335A 19V
TBD
N/S
BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140
TBD
BATTERY PANASONIC LI-ION 4S2P 4.4A
CGR-B/8B5AE
TBD
BATTERY SIMPLO LI-ION 4S2P 4.4A 9163020
TBD
9
MODEM BOARD
54.T50V7.001
14
BLUETOOTH MODULE W/ANTENNA
54.T48V7.001
N/S
WIRELESS LAN BOARD (802.11b+g) INTEL
KI.CAX01.005
12
LAUNCH BOARD
55.T50V7.001
31
TOUCH PAD BOARD
55.T50V7.002
Battery
Boards
Chapter 6
99
TravelMate 4000
Picture
No.
Partname And Description
Part Number
Cables
N/S
FFC CABLE - TP/B TO MB
50.T50V7.001
N/S
MODEM CABLE
50.T50V7.002
N/S
POWER CORD US (3 PIN)
27.A03V7.001
POWER CORD PRC (3 PIN)
27.A03V7.003
POWER CORD KOERA ( Pin)
27.T23V7.006
POWER CORD EU (3 PIN)
27.A03V7.002
POWER CORD UK (3 PIN)
27.A03V7.004
POWER CORD ITALIAN (3 PIN)
27.A03V7.005
POWER CORD- SWISS
27.A03V7.007
POWER CORD AU (3 PIN)
27.A03V7.008
POWER CORD DANISH (3 PIN)
27.A03V7.006
POWER CORD AF (3 PIN)
27.T48V7.001
MIDDEL COVER ERGO W/BUTTON
42.T50V7.001
Case/Cover/Bracket Assembly
13
Note: The middle cover on the exploded
diagram is non-ergo for Aspire series.
10
UPPER CASE ERGO W/TP, TP BRACKET,
TP TO TP BOARD FFC CABLE
60.T50V7.001
Note: The upper case on the exploded
diagram is non-ergo for Aspire series.
100
1
LOWER CASE W/SPEAKER
60.T51V7.001
37
I/O BEZEL
42.T51V7.001
23
DIMM/WIRELESS COVER
42.T50V7.002
Chapter 6
TravelMate 4000
Picture
No.
Partname And Description
Part Number
22
HEATSINK COVER
42.T50V7.003
26
HDD COVER
42.T50V7.004
36
3 IN 1 DUMMY COVER
42.T51V7.002
Note: The image on the left is 3 in 1 cover. If
that is 3 in 1 dummy cover, there is no card
insert space on the cover.
25
HDD BRACKET
33.T50V7.001
N/S
WIRELESS LAN ANTENNA
50.T50V7.003
N/S
INTEL PENTIUM M 1.5G 2M 400FSB
uFCPGA2 SL6F9 B-1 STEPPING
KC.N0001.715
INTEL PENTIUM M 1.6G 2M 400FSB
uFCPGA2 SL7EG B-1 STEPPING
KC.N0001.725
INTEL PENTIUM M 1.7G 2M 400FSB
uFCPGA2 SL7EP B-1 STEPPING
KC.N0001.735
INTEL PENTIUM M 1.8G 2M 400FSB
uFCPGA2 SL7EN B-1 STEPPING
KC.N0001.745
INTEL PENTIUM M 2.0G 2M 400FSB
uFCPGA2 SL7EM B-1 STEPPING
KC.N0001.755
Communication Module
CPU
Optical Disc Drive Module
N/S
Chapter 6
DVD-ROM MODULE 8X QSI SDR-083
6M.T51V7.008
DVD/CDRW COMBO MODULE 24X QSI
SBW-242C
6M.T51V7.001
DVD/CDRW COMBO MODULE KME UIDA760
6M.T51V7.002
DVD DUAL MODULE QSI SDW-042
6M.T51V7.003
DVD DUAL MODULE PIONEER DVR-K14RA
6M.T51V7.004
DVD DUAL MODULE LITE-ON SOSW-852S
6M.T51V7.005
DVD SUPER MULTI MODULE KME UJ-830B
6M.T51V7.006
DVD SUPER MULTI MODULE HLDS GSA4080N
6M.T51V7.007
101
TravelMate 4000
Picture
No.
27
Partname And Description
Part Number
DVD-ROM DRIVE 8X QSI SDR-083
KV.00803.003
DVD/CDRW COMBO DRIVE 24X QSI SBW242C
KO.02407.014
DVD/CDRW COMBO DRIVE 24X KME UIDA760
KO.02406.008
DVD DUAL DRIVE QSI SDW-042
KU.00403.001
DVD DUAL DRIVE PIONEER DVR-K14RA
KU.00805.001
DVD DUAL DRIVE LITE-ON SOSW-852S
KU.00805.001
DVD SUPER MULTI DRIVE KME UJ-830B
KU.00807.003
DVD SUPER MULTI DRIVE HLDS GSA4080N
TBD
29
OPTICAL DEVICE HOLDER-FIX
42.T51V7.003
28
DVD-ROM BEZEL FOR QSI
42.T51V7.004
DVD/CDRW BEZEL FOR QSI
42.T50V7.008
DVD/CDRW BEZEL FOR KME
42.T50V7.009
DVD DUAL BEZEL FOR QSI
42.T50V7.010
DVD DUAL BEZEL FOR PIONEER
42.T50V7.011
DVD DUAL BEZEL FOR LITE-ON
42.T50V7.012
DVD SUPER MULTI BEZEL FOR KME
42.T50V7.013
DVD SUPER MULTI BEZEL FOR HLDS
42.T50V7.014
30G HGST 2.5" 4200 Moraga+
HTS424030M9AT00 13G1486 fw:DA1017
KH.03007.006
Toshiba Pluto 30G 4200rpm MK3025GAS
KH.03004.002
Seagate 30G ST93015A,2MB F/W:4.05
KH.03001.001
40G HGST 2.5" 4200 Moraga+
HTS424040M9AT00 13G1132 fw:DA1017
KH.04007.010
Toshiba PLUTO 40G 4200rpm MK4025GAS
,KA100A F/W:KA100A
KH.04004.002
SEAGATE 40G 4200rpm ST94019A, 2MB F/
W:3.05
KH.04001.010
HGST 60G 4200rpm MORAGA
IC25N060ATMR04-0 08K0634 F/W:AD4A
KH.06007.006
Toshiba PLUTO 60G 4200rpm MK6025GAS
(phase in Mar/Apr) F/W:KA200A
KH.06004.003
HGST 80G 4200rpm MORAGA
IC25N080ATMR04-0 08K635 F/W:AD4A
KH.08007.007
TOSHIBA PLUTO 80G 4200rpm
MK8025GAS, 8MB F/W:KA023A
KH.08004.001
HDD/Hard Disk Drive
24
Keyboard
102
Chapter 6
TravelMate 4000
Picture
No.
11
Partname And Description
TM4500/TM4000/TM2300 KEYBOARD
DARFON US International
Part Number
KB.T5007.001
Note: The keyboard on the exploded diagram
is non-ergo for Aspire series.
Chapter 6
TM4500/TM4000/TM2300 KEYBOARD
DARFON Chinese
KB.T5007.002
TM4500/TM4000/TM2300 KEYBOARD
DARFON Spanish
KB.T5007.003
TM4500/TM4000/TM2300 KEYBOARD
DARFON Thai
KB.T5007.004
TM4500/TM4000/TM2300 KEYBOARD
DARFON Brazilian Protugese
KB.T5007.005
TM4500/TM4000/TM2300 KEYBOARD
DARFON Korea
KB.T5007.006
TM4500/TM4000/TM2300 KEYBOARD
DARFON UK
KB.T5007.007
TM4500/TM4000/TM2300 KEYBOARD
DARFON German
KB.T5007.008
TM4500/TM4000/TM2300 KEYBOARD
DARFON Italian
KB.T5007.009
TM4500/TM4000/TM2300 KEYBOARD
DARFON French
KB.T5007.010
TM4500/TM4000/TM2300 KEYBOARD
DARFON Swiss/G
KB.T5007.011
TM4500/TM4000/TM2300 KEYBOARD
DARFON Portuguese
KB.T5007.012
TM4500/TM4000/TM2300 KEYBOARD
DARFON Arabic
KB.T5007.013
TM4500/TM4000/TM2300 KEYBOARD
DARFON Belgium
KB.T5007.014
TM4500/TM4000/TM2300 KEYBOARD
DARFON Sweden
KB.T5007.015
TM4500/TM4000/TM2300 KEYBOARD
DARFON Czech
KB.T5007.016
TM4500/TM4000/TM2300 KEYBOARD
DARFON Hungaian
KB.T5007.017
TM4500/TM4000/TM2300 KEYBOARD
DARFON Norway
KB.T5007.018
TM4500/TM4000/TM2300 KEYBOARD
DARFON Danish
KB.T5007.019
TM4500/TM4000/TM2300 KEYBOARD
DARFON Turkish
KB.T5007.020
TM4500/TM4000/TM2300 KEYBOARD
DARFON Canadian French
KB.T5007.021
TM4500/TM4000/TM2300 KEYBOARD
DARFON Japanese
KB.T5007.022
TM4500/TM4000/TM2300 KEYBOARD
DARFON Greek
KB.T5007.023
TM4500/TM4000/TM2300 KEYBOARD
DARFON Hebrew
KB.T5007.024
TM4500/TM4000/TM2300 KEYBOARD
DARFON Russian
KB.T5007.025
103
TravelMate 4000
Picture
No.
Partname And Description
Part Number
LCD Module
N/S
20
17
104
LCD MODULE 14.1 IN. XGA AU B141XG05
6M.T51V7.011
LCD MODULE 14.1 IN. XGA QDI
QD141XLH12
6M.T51V7.012
LCD MODULE 14.1 IN. XGA CMO N141XBL01
6M.T51V7.013
LCD MODULE 15 IN. XGA AU B150XG01
6M.T50V7.011
LCD MODULE 15 IN. XGA QDI QDI150XL0601
6M.T50V7.012
LCD MODULE 15 IN. XGA HANNSTAR
HSD150PX14-A07
6M.T50V7.013
LCD MODULE 15 IN. XGA SAMSUNG
LTN150XB-L03
6M.T50V7.014
LCD MODULE 15 IN. XGA HITACHI
TX38D81VC1CAB
6M.T50V7.015
LCD MODULE 15.4 IN. WXGA QDI
QD15TL02-01
6M.T50V7.019
LCD 14.1 IN. TFT XGA AU B141XG05
LK.14105.006
LCD 14.1 IN. TFT XGA QDI QD141XLH12
LK.14109.003
LCD 14.1 IN. TFT XGA CMO N141XB-L01
LK.1410D.003
LCD 15" TFT XGA AU B150XG01 V2 (spwgB)
LK.15005.001
LCD 15 IN. XGA QDI QDI150XL06-01
LK.15009.002
LCD 15 IN. XGA HANNSTAR HSD150PX14A07
LK.15007.009
LCD 15 IN. XGA SAMSUNG LTN150XB-L03
LK.15006.004
LCD 15 IN. TFT XGA HITACHI
TX38D81VC1CAB (SPWG-B)
LK.15004.006
LCD 15.4 IN. WXGA QDI QD15TL02-01
LK.15409.001
LCD INVERTER BOARD
19.T50V7.001
Chapter 6
TravelMate 4000
Picture
No.
16
Partname And Description
Part Number
LCD CABLE - 14.1 IN. XGA
50.T51V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 14 IN. - L
33.T51V7.001
LCD BRACKET W/HINGE 14 IN. - R
33.T51V7.002
19
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
18
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
38
20
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD PANEL W/LOGO ANTENNA 15.4 IN.
60.T50V7.005
LCD BEZEL W/RUBBER PAD 14 IN.
60.T51V7.002
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
MAINBOARD 855GME M11 64MB W/PCMCIA
SLOT W/O CPU MEMORY
LB.T5206.001
MAINBOARD 855GME UMA W/PCMCIA
SLOT W/O CPU MEMORY
LB.T5306.001
256MB NANYA SO-DIMM DDR333 256MB
NT256D64SH8BAGM-6K (.14u)
KN.25603.009
256M Infineon SO-DIMM DDR333
HYS64D32020GDL-6-C (.11u/B) (Sample
April/M, 09/04' by firm PO)
KN.25602.022
256M Infineon SO-DIMM DDR333 256MB
HYS64D32020HDL-6-C 32x64 (.11u/G) (MP in
Sept.)
KN.25602.012
256M Micron SO-DIMM DDR333 256MB
MT4VDDT3264HG-335C2
KN.25604.016
256M Samsung SO-DIMM DDR333 256MB
M470L3224FT0-CB3 (.13u)
KN.2560B.008
256M Hynix SO-DIMM DDR333 256MB
HYMD232M646D6-J AA
KN.2560G.001
Main Board
2
Memory
N/S
Chapter 6
105
TravelMate 4000
Picture
No.
Partname And Description
Part Number
N/S
512M Infineon SO-DIMM DDR333 512MB
HYS64D64020GBDL-6-C (.11u/B)
KN.51202.013
N/S
512MB NANYA SO-DIMM DDR333 512MB
NT512D64SH8A0FM-6K
KN.51203.011
N/S
512MB Micron SO-DIMM DDR333 512MB
MT8VDDT6464HDG-335C1 (.11u),
KN.51204.013
N/S
SPEAKER SET
23.T50V7.001
21
THERMAL MODULE
60.T50V7.007
4
VGA HEATSINK W/PAD
34.T50V7.001
7
NAME PLATE
47.T51V7.001
N/S
RUBBER FOOT
47.T50V7.002
N/S
LCD SCREW RUBBER PAD
47.T50V7.003
32
LCD BEZEL RUBBER PAD
47.T50V7.004
N/S
SCREW M2.0X3.0-I-NI-NYLOK
86.A03V7.012
C
SCREW I2.5*3M-BNIH(M2.5L3)
86.T25V7.012
N/S
SCREW M2.5*4L-BZN-NYLOK
86.A03V7.006
N/S
SCREW M2.0X5-I-NI-NYLOK
86.T23V7.006
D
SCREW MM25060IL69
86.A08V7.004
N/S
SCREW M2.0*5-I(NI)(NYLOK)
86.T23V7.010
K
SCREW M2.0X2.5-I-NI-NYLOK
86.A03V7.007
G
SCREW I2*3M-NIHY (M2L3)
86.T25V7.008
I
SCREW M1.7*3.0-I (BK)
86.T50V7.001
A
SCREW I3*3.5M-NIH(M3L3.5)
86.A03V7.011
Speaker
Heatsink
Miscellaneous
Screw
106
Chapter 6
TravelMate 4500
Picture
No.
Partname And Description
Part Number
Adapter
ADAPTER 65W 3 PIN DELTA SADP-65KB BF
19V
TBD
ADAPTER 65W 3 PIN LITE-ON PA-1650-02
QA 19V
TBD
ADAPTER 65W 3 PIN LI-SHIN SLS0335A 19V
TBD
BATTERY SANYO LI-ION 4S2P 4.4A
4UR18650F-2-QC140
TBD
BATTERY PANASONIC LI-ION 4S2P 4.4A
CGR-B/8B5AE
TBD
BATTERY SIMPLO LI-ION 4S2P 4.4A 9163020
TBD
MODEM BOARD
54.T50V7.001
BLUETOOTH MODULE W/ANTENNA
54.T48V7.001
WIRELESS LAN BOARD (802.11b+g) INTEL
KI.CAX01.005
LAUNCH BOARD
55.T50V7.001
TOUCH PAD BOARD
55.T50V7.002
FFC CABLE - TP/B TO MB
50.T50V7.001
MODEM CABLE
50.T50V7.002
POWER CORD US (3 PIN)
27.A03V7.001
POWER CORD PRC (3 PIN)
27.A03V7.003
POWER CORD KOERA ( Pin)
27.T23V7.006
POWER CORD EU (3 PIN)
27.A03V7.002
POWER CORD UK (3 PIN)
27.A03V7.004
POWER CORD ITALIAN (3 PIN)
27.A03V7.005
POWER CORD- SWISS
27.A03V7.007
POWER CORD AU (3 PIN)
27.A03V7.008
POWER CORD DANISH (3 PIN)
27.A03V7.006
POWER CORD AF (3 PIN)
27.T48V7.001
MIDDEL COVER ERGO W/BUTTON
42.T50V7.001
UPPER CASE ERGO W/TP, TP BRACKET,
TP TO TP BOARD FFC CABLE
60.T50V7.001
LOWER CASE FOR SWAP W/SPEAKER
60.T50V7.002
I/O BEZEL FOR DOCKING
42.T50V7.005
DIMM/WIRELESS COVER
42.T50V7.002
HEATSINK COVER
42.T50V7.003
HDD COVER
42.T50V7.004
3 IN 1 COVER
42.T50V7.006
HDD BRACKET
33.T50V7.001
WIRELESS LAN ANTENNA
50.T50V7.003
Battery
Boards
Cable
Case/Cover/Bracket Assembly
Communication Module
CPU
Chapter 6
107
TravelMate 4500
Picture
No.
Partname And Description
Part Number
INTEL PENTIUM M 1.5G 2M 400FSB
uFCPGA2 SL6F9 B-1 STEPPING
KC.N0001.715
INTEL PENTIUM M 1.6G 2M 400FSB
uFCPGA2 SL7EG B-1 STEPPING
KC.N0001.725
INTEL PENTIUM M 1.7G 2M 400FSB
uFCPGA2 SL7EP B-1 STEPPING
KC.N0001.735
INTEL PENTIUM M 1.8G 2M 400FSB
uFCPGA2 SL7EN B-1 STEPPING
KC.N0001.745
INTEL PENTIUM M 2.0G 2M 400FSB
uFCPGA2 SL7EM B-1 STEPPING
KC.N0001.755
DVD/CDRW COMBO MODULE 24X QSI
SBW-242C SWAP
6M.T50V7.001
DVD/CDRW COMBO DRIVE 24X QSI SBW242C
KO.02407.014
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD/CDRW BEZEL FOR QSI
42.T50V7.008
DVD/CDRW COMBO MODULE KME UIDA760 SWAP
6M.T50V7.002
DVD/CDRW COMBO DRIVE 24X KME UIDA760
KO.02406.008
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD/CDRW BEZEL FOR KME
42.T50V7.009
DVD DUAL MODULE QSI SDW-042 SWAP
6M.T50V7.003
DVD DUAL DRIVE QSI SDW-042
KU.00403.001
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD DUAL BEZEL FOR QSI
42.T50V7.010
DVD DUAL MODULE PIONEER DVR-K14RA
SWAP
6M.T50V7.004
DVD DUAL DRIVE PIONEER DVR-K14RA
KU.00805.001
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD DUAL BEZEL FOR PIONEER
42.T50V7.011
DVD DUAL MODULE LITE-ON SOSW-852S
SWAP
6M.T50V7.005
DVD DUAL DRIVE LITE-ON SOSW-852S
KU.00804.007
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
Combo Module
108
Chapter 6
TravelMate 4500
Picture
No.
Partname And Description
Part Number
DVD DUAL BEZEL FOR LITE-ON
42.T50V7.012
DVD SUPER MULTI MODULE KME UJ-830B
SWAP
6M.T50V7.006
DVD SUPER MULTI DRIVE KME UJ-830B
KU.00807.003
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD SUPER MULTI BEZEL FOR KME
42.T50V7.013
DVD SUPER MULTI MODULE HLDS GSA4080N SWAP
6M.T50V7.007
DVD SUPER MULTI DRIVE HLDS GSA4080N
TBD
OPTICAL DEVICE CONNECTOR BOARD W/
MYLARY
55.T50V7.003
OPTICAL DEVICE HOLDER-SWAP
42.T50V7.007
DVD SUPER MULTI BEZEL FOR HLDS
42.T50V7.014
30G HGST 2.5" 4200 Moraga+
HTS424030M9AT00 13G1486 fw:DA1017
KH.03007.006
Toshiba Pluto 30G 4200rpm MK3025GAS
KH.03004.002
Seagate 30G ST93015A,2MB F/W:4.05
KH.03001.001
40G HGST 2.5" 4200 Moraga+
HTS424040M9AT00 13G1132 fw:DA1017
KH.04007.010
Toshiba PLUTO 40G 4200rpm MK4025GAS
,KA100A F/W:KA100A
KH.04004.002
SEAGATE 40G 4200rpm ST94019A, 2MB F/
W:3.05
KH.04001.010
HGST 60G 4200rpm MORAGA
IC25N060ATMR04-0 08K0634 F/W:AD4A
KH.06007.006
Toshiba PLUTO 60G 4200rpm MK6025GAS
(phase in Mar/Apr) F/W:KA200A
KH.06004.003
HGST 80G 4200rpm MORAGA
IC25N080ATMR04-0 08K635 F/W:AD4A
KH.08007.007
TOSHIBA PLUTO 80G 4200rpm
MK8025GAS, 8MB F/W:KA023A
KH.08004.001
TM4500/TM4000/TM2300 KEYBOARD
DARFON US International
KB.T5007.001
TM4500/TM4000/TM2300 KEYBOARD
DARFON Chinese
KB.T5007.002
TM4500/TM4000/TM2300 KEYBOARD
DARFON Spanish
KB.T5007.003
TM4500/TM4000/TM2300 KEYBOARD
DARFON Thai
KB.T5007.004
TM4500/TM4000/TM2300 KEYBOARD
DARFON Brazilian Protugese
KB.T5007.005
TM4500/TM4000/TM2300 KEYBOARD
DARFON Korea
KB.T5007.006
HDD/Hard Disk Drive
Keyboard
Chapter 6
109
TravelMate 4500
Picture
No.
Partname And Description
Part Number
TM4500/TM4000/TM2300 KEYBOARD
DARFON UK
KB.T5007.007
TM4500/TM4000/TM2300 KEYBOARD
DARFON German
KB.T5007.008
TM4500/TM4000/TM2300 KEYBOARD
DARFON Italian
KB.T5007.009
TM4500/TM4000/TM2300 KEYBOARD
DARFON French
KB.T5007.010
TM4500/TM4000/TM2300 KEYBOARD
DARFON Swiss/G
KB.T5007.011
TM4500/TM4000/TM2300 KEYBOARD
DARFON Portuguese
KB.T5007.012
TM4500/TM4000/TM2300 KEYBOARD
DARFON Arabic
KB.T5007.013
TM4500/TM4000/TM2300 KEYBOARD
DARFON Belgium
KB.T5007.014
TM4500/TM4000/TM2300 KEYBOARD
DARFON Sweden
KB.T5007.015
TM4500/TM4000/TM2300 KEYBOARD
DARFON Czech
KB.T5007.016
TM4500/TM4000/TM2300 KEYBOARD
DARFON Hungaian
KB.T5007.017
TM4500/TM4000/TM2300 KEYBOARD
DARFON Norway
KB.T5007.018
TM4500/TM4000/TM2300 KEYBOARD
DARFON Danish
KB.T5007.019
TM4500/TM4000/TM2300 KEYBOARD
DARFON Turkish
KB.T5007.020
TM4500/TM4000/TM2300 KEYBOARD
DARFON Canadian French
KB.T5007.021
TM4500/TM4000/TM2300 KEYBOARD
DARFON Japanese
KB.T5007.022
TM4500/TM4000/TM2300 KEYBOARD
DARFON Greek
KB.T5007.023
TM4500/TM4000/TM2300 KEYBOARD
DARFON Hebrew
KB.T5007.024
TM4500/TM4000/TM2300 KEYBOARD
DARFON Russian
KB.T5007.025
LCD MODULE 15 IN. XGA AU B150XG01
6M.T50V7.011
LCD 15" TFT XGA AU B150XG01 V2 (spwgB)
LK.15005.001
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. XGA QDI QDI150XL0601
6M.T50V7.012
LCD
110
Chapter 6
TravelMate 4500
Picture
Chapter 6
No.
Partname And Description
Part Number
LCD 15 IN. XGA QDI QDI150XL06-01
LK.15009.002
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. XGA HANNSTAR
HSD150PX14-A07
6M.T50V7.013
LCD 15 IN. XGA HANNSTAR HSD150PX14A07
LK.15007.009
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. XGA SAMSUNG
LTN150XB-L03
6M.T50V7.014
LCD 15 IN. XGA SAMSUNG LTN150XB-L03
LK.15006.004
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. XGA HITACHI
TX38D81VC1CAB
6M.T50V7.015
LCD 15 IN. TFT XGA HITACHI
TX38D81VC1CAB (SPWG-B)
LK.15004.006
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. XGA
50.T50V7.004
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. SXGA CMO N150P2L04
6M.T50V7.016
LCD 15" TFT SXGA+ CMO N150P2-L04
LK.1500D.003
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. SXGA
50.T50V7.005
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
111
TravelMate 4500
Picture
No.
Partname And Description
Part Number
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. SXGA AU B150PG01
6M.T50V7.017
LCD 15" TFT SXGA+ AU B150PG01
LK.15005.002
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. SXGA
50.T50V7.005
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15 IN. SXGA SAMSUNG
LTN150P4-L03
6M.T50V7.018
LCD 15 IN. TFT SXGA+ SAMSUNG
LTN150P4-L03 (150nit)
LK.15006.006
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15 IN. SXGA
50.T50V7.005
LCD BRACKET W/HINGE 15 IN. - L
33.T50V7.002
LCD BRACKET W/HINGE 15 IN. - R
33.T50V7.003
LCD PANEL W/LOGO ANTENNA 14/15 IN.
60.T50V7.003
LCD BEZEL W/RUBBER PAD 15 IN.
60.T50V7.004
LCD MODULE 15.4 IN. WXGA QDI
QD15TL02-01
6M.T50V7.019
LCD 15.4 IN. WXGA QDI QD15TL02-01
LK.15409.001
LCD INVERTER BOARD
19.T50V7.001
LCD CABLE - 15.4 IN. WXGA
50.T50V7.006
LCD BRACKET W/HINGE 15.4 IN. - L
33.T50V7.004
LCD BRACKET W/HINGE 15.4 IN. - R
33.T50V7.005
LCD PANEL W/LOGO ANTENNA 15.4 IN.
60.T50V7.005
LCD BEZEL W/RUBBER PAD 15.4 IN.
60.T50V7.006
MAINBOARD 855GME M11 64MB DOCKING
3 IN 1 W/PCMCIA SLOT W/O CPU MEMORY
LB.T5006.001
MAINBOARD 855GME UMA DOCKING 3 IN 1
W/PCMCIA SLOT W/O CPU MEMORY
LB.T5106.001
256MB NANYA SO-DIMM DDR333 256MB
NT256D64SH8BAGM-6K (.14u)
KN.25603.009
256M Infineon SO-DIMM DDR333
HYS64D32020GDL-6-C (.11u/B) (Sample
April/M, 09/04' by firm PO)
KN.25602.022
256M Infineon SO-DIMM DDR333 256MB
HYS64D32020HDL-6-C 32x64 (.11u/G) (MP in
Sept.)
KN.25602.012
256M Micron SO-DIMM DDR333 256MB
MT4VDDT3264HG-335C2
KN.25604.016
Mainboard
Memory
112
Chapter 6
TravelMate 4500
Picture
No.
Partname And Description
Part Number
256M Samsung SO-DIMM DDR333 256MB
M470L3224FT0-CB3 (.13u)
KN.2560B.008
256M Hynix SO-DIMM DDR333 256MB
HYMD232M646D6-J AA
KN.2560G.001
512M Infineon SO-DIMM DDR333 512MB
HYS64D64020GBDL-6-C (.11u/B)
KN.51202.013
512MB NANYA SO-DIMM DDR333 512MB
NT512D64SH8A0FM-6K
KN.51203.011
512MB Micron SO-DIMM DDR333 512MB
MT8VDDT6464HDG-335C1 (.11u),
KN.51204.013
SPEAKER SET
23.T50V7.001
THERMAL MODULE
60.T50V7.007
VGA HEATSINK W/PAD
34.T50V7.001
NAME PLATE
47.T50V7.001
RUBBER FOOT
47.T50V7.002
LCD SCREW RUBBER PAD
47.T50V7.003
LCD BEZEL RUBBER PAD
47.T50V7.004
WEIGHT SAVER
60.T50V7.008
2nd HDD BASE W/CONNECT
60.T50V7.009
2nd HDD COVER
42.T50V7.015
2nd HDD BRACKET KIT
6K.T50V7.001
SCREW M2.0X3.0-I-NI-NYLOK
86.A03V7.012
SCREW I2.5*3M-BNIH(M2.5L3)
86.T25V7.012
SCREW M2.5*4L-BZN-NYLOK
86.A03V7.006
SCREW M2.0X5-I-NI-NYLOK
86.T23V7.006
SCREW MM25060IL69
86.A08V7.004
SCREW M2.0*5-I(NI)(NYLOK)
86.T23V7.010
SCREW M2.0X2.5-I-NI-NYLOK
86.A03V7.007
SCREW I2*3M-NIHY (M2L3)
86.T25V7.008
SCREW M1.7*3.0-I (BK)
86.T50V7.001
SCREW I3*3.5M-NIH(M3L3.5)
86.A03V7.011
Speaker
SPEAKER
Heatsink
Miscellaneous
Weights Saver
2nd HDD Base
2nd HDD Cover
2nd HDD Bracket Kit
Screw
Chapter 6
113
114
Chapter 6
Chapter 6
115
Appendix A
Model Definition and Configuration
TravelMate 4000 Series
Model Number
LCD
CPU
4001WLCi
15.4"
WXGA
4001WLMi
HDD
PM 715
(1.5GHz/2M)
DDR333 1
or
2x256MB
40GB
24x Combo
11b/g
XPH
15.4"
WXGA
PM 715
(1.5GHz/2M)
DDR333 1
or
2x256MB
40/
60GB
4x DVDDual
11b/g
XPH
4001WFLMi
15.4"
WXGA
PM 715
(1.5GHz/2M)
DDR333
1x256MB
40GB
4x DVDDual
11b/g
IBM DOS
4001WFLCi
15.4"
WXGA
PM 715
(1.5GHz/2M)
DDR333
1x256MB
40GB
24x Combo
11b/g
IBM DOS
4001WNLCi
15.4"
WXGA
PM 715
(1.5GHz/2M)
DDR333
1x256MB
40GB
24x Combo
11b/g
Linux
4001WNLMi
15.4"
WXGA
PM 715
(1.5GHz/2M)
DDR333
1x256MB
40GB
4x DVDDual
11b/g
Linux
4001LCi
15.0"
XGA
PM 715
(1.5GHz/2M)
DDR333
2x256MB
40GB
24x Combo
11b/g
XPH
4001LMi
15.0"
XGA
PM 715
(1.5GHz/2M)
DDR333
2x256MB
40/
60GB
4x DVDDual
11b/g
XPH
Appendix A
ODD
Wireless
LAN
Memory
OS
116
Appendix B
Test Compatible Components
This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the TravelMate 2300/4000/4500
series Compatibility Test Report released by the Acer Mobile System Testing Department.
NOTE: Test Compatible List is NOT ready when the service guide is released. We will update test compatible
list accordingly once we got test report.
Appendix B
119
Microsoft® Windows® XP Pro Environment Test
Item
Processor
Specifications
Intel Celeron 1.3GHz
Intel Celeron 1.4GHz
Intel PMP 705Banias 1.5 GHz, Tj85
Intel Dothan 715/1.5GHz
Intel Dothan 725/1.6GHz
Intel Dothan 735/1.7GHz
Intel Dothan 745/1.8GHz
Intel Dothan 755/2.0GHz
Memory
256MB NANYA SO-DIMM DDR333 NT256D64SH8BAGM
256MB Infineon SO-DIMM DDR333 HYS64D32020GDL
256MB Infineon SO-DIMM DDR333 HYS64D32020HDL
256MB Micron SO-DIMM DDR333 MT4VDDT3264HG
256MB Samsung SO-DIMM DDR333 M470L3224FT0
256MB Hynix SO-DIMM DDR333 HYMD232M646D6
512M Infineon SO-DIMM DDR333 HYS64D64020GBDL
512MB Micron SO-DIMM DDR333 MT8VDDT6464HDG
1GMB Elpida SO-DIMM DDR333 EBD11UD8ADDA
LCD
14.1"XGA B141XG05 (AU)
14.1"XGA QD141X1LH12 (QDI)
14.1"XGA N141XB-L01 (CMO)
LCD
15.0"XGA B150XG01 V. 2 (AU)
15.0"XGA B150XG02 V.2 170 nits (AU)
15.0"XGA QD150XL06-01 160nits (QDI)
15.0"XGA LP150X08-A3 160nits (LG)
15.0"XGA HSD150PX14-A07 (Hannstar)
15.0"XGA LTN150XB-L03-C00 (Samsung)
15.0"XGA TX38D81VC1CAB Rev.B (Hitachi)
15.0"XGA N150X3-L07 (CMO/IDT)
15.0"XGA CLAA150XH01-N (CPT)
LCD
15.0"SXGA+ B150PG01 with NEC driver IC (AU)
15.0"SXGA+ N150P2-L04 (200nit) (IDT(CMO)
15.0"SXGA+ B150PG03 (200nit) (AU)
15.0"SXGA+ LTN150P4-L03 (Samsung)
15.0"SXGA+ QD15FL02 RV.01 (200nit) (QDI)
LCD
15.4"WXGA B154EW01 V.5 (170nit) (AU)
15.4"WXGA QD15TL02-01 (TN type) (185nit) (QDI)
15.4"WXGA N154I1-L09 (185nit) (CMO/IDT)
15.4"WXGA LTN154X2-L02 Low cost (Samsung)
15.4"WXGA Low cost TN TYPE (CPT)
15.4"WXGA Low Cost TN TYPE (LG)
15.4"WXGA TX39D85VC1FAA Low Cost (Hitachi)
15.4"WSXGA+ LP154W02-B1 (185nit) (LG)
15.4"WSXGA+ TX39D99VC1FAA (Hitachi)
15.4"WSXGA+ Low cost (Samsung)
120
Appendix B
Item
Hard Disk Drive
Specifications
30G HGST Moraga+ HTS424030M9AT00
30G Toshiba MK3025GAS30GB
30G Seagate 30G ST93015A
40G HGST Moraga+ HTS424040M9AT0040GB
40G Toshiba PLUTO MK4025GAS
40G SEAGATE ST94019A40G
60G HGST Moraga IC25N060ATMR04-0
60G TOSHIBA Neptune MK6021GAS
80G HGST Moraga IC25N080ATMR04
80G TOSHIBA Pluto MK8025GAS
DVD-ROM Drive 8X
DVD-ROM QSI SDR-083
DVD/CD-RW Combo
KME UJDA-760
DVD-dual
DVR-K14RA
QSI SBW-242C
Lite-on SOSW-852S
QSI SDW-042
QSI SDW-082
DVD-Super Multi
KME UJ-830B
HLDS GSA-4080N
AC Adapter (3 pin)
Delta NB Asapter 65W, SADP-65KB BF
Lite-on NB Adapter 65W, PA-1650-02
LSE NB Adapter 65W, P0335A1965
Power Cord
Battery Li-Ion, 8 cells
King Cord
Sanyo 4UR18650F-2-QC140 ZL1,4S2P,4.4A / AHA842223I4
Panasonic CGR-B/8B5AE,ZL1,4S2P,14.8V,4.4A / AHA84222050
Simplo 916-3020 4S2P,4.4A / AHA842221I0
Sanyo 4UR18650F-QC141 ZL1,4S1P,2.2A / AHA44122A01
Panasonic CGR-B/423AE,ZL1,4S1P,14.8V,2.2A / AHA44122712
Simplo 916-2990 4S1P,2.2A / AHA44122909
Sanyo 3UF103450P-2-QC148 ZL1,3S2P,3.8A 6cell 2nd Bat /
AHA63217219
CRT Port
CRT Monitor:
ViewSonic PF775
Philips Brilliance 109P 19"
LCD Monitor:
LCD Quanta ADT 20"
LCD akia KX1
Projector:
Panasonic PT-LC80U
Parallel Port
Printer:
HP Desk Jet 840C
HP Laser Jet 5M
HP Deskjet 450
Cable:
LL5 cable
Appendix B
121
Item
1394 Port
Specifications
HDD:
IEEE 1394 (Fire Wire)/USB 1.1 Combo Hard Drive
CCD:
1394 CCD (APLUX C102T)
1394 CardBus Card:
IEEE 1394 CardBus Card \DV Magician\UPMOST
Cable:
1394 four to four cable
USB 2.0
HUB:
Highspeed\4 Port
UNION START UH-364
W-FORCE 4 Port USB2.0 Super Mini Hub
HDD:
USB HDD:VIPower(Smart Family Disk)
DVD/CD-RW:
Pioneer DVR-104
Ricoh MP5125A
YAMAHA CD/RW-70
Printer:
HP3425 Printer
Handy Drive:
SanDisk Cruzer USB 2.0 Handy Drive 256MB
USB Port
USB Mouse:
BenQ M102-G80
Logitech Mouse M-BE58
Microsoft Wheel Mouse Optical USB & PS2 Compatible
Acer MP0930
USB Keyboard:
Microsoft Internet Keyboard Pro
BenQ 6511-ME
KILITEK
USB KeyPad:
LUNARIS TK-LU2BSV USB Keypad
122
Appendix B
Item
USB Port
Specifications
USB CCD:
ViewQuest NB330
USB HDD:
HD 530 Tested to comply with FCC Standards
USB FDD:
Teac USB FDD
Yano USB FDD UFD-04
NEC USB FDD
Mitsumi USB FDD D353FUE
USB Speaker:
J-S USB 3D Speaker /J1321
USB Printer:
Canon BJC-3000
HD DeskJet 930C
HP DeskJet 840C
USB Hub:
PCI_ USB HUB\UH-400
USB Hub /UH-9124Z
USB LAN:
BUFFALO USB-10/100M Ethernet LUX-TX
USB Handy Drive:
JMTEK USB 1.1 Handy Drive 128MB
GB LAN HUB
3COM SUPER STACK II \ 3C16611 24port
PS/2 Port
Keyboard:
Microsoft Internet Keyboard Pro
BTC Keyboard
PS/2 Keypad:
PC Keypad KB-5640
Mouse:
Logitech M-C48
COM Port
Mouse:
Logitech Serial Mouse M-MM43
S-Video
TV:
SONY Trinitron 14"\PVM-14M2U
PC Card
Modem Card:
Psion - Gold Card Glabal 56K+Fax
SyCard:
16bit
32bit
16 bit LAN Card:
3COM 10M LAN Card (3CCFE589ET)
Xircom EtherNet 10/100+Modem56 CEM56-100
CardBus LAN Card:
3COM 10/100 CardBus LAN Card (3CCFE575CT)
SCSI:
Adaptec SlimSCSI APA-1460D Card
Adaptec SlimSCSI 1480A CardBus UltraSCSI Card
RATOC REX-CB80
Appendix B
123
Item
PC Cards
Specifications
LAN+Modem card:
Xircom CreditCard Ethernet + Modem 56k (CEM56-100)
ATA Card:
4 in1 WIN&MAC Card reader+Transcend 128MB
Apapter CF Card Read + PNY CF CARD 128MB
Wireless LAN Card:
CISCO AIRONET 350 SERIES\AIR-PCM350
Linksys WPC11ver.4
Intel(R)PRO / Wireless 2011B LAN PC Card
Memory Card
MMC:
SanDisk 64MB
Compact Flash Card:
PNY 128MB
Memory Stick:
SONY 256MB
SD Memory Card:
Apacer 128MB
Toshiba 256MB
Smart Media:
Transcend 128 MB
Fuji 128 MB
Audio Jacks
Speaker:
J-S 3D Speaker /J-2202
Headphone:
PHILIPS Stereo Headphone SBC HP090
Labtec Stereo Headphone Elite-840
Earphone:
Philips Earphone
Microphone:
Condenser MIC. EM-420T
Labtec deskmic 524 Microphone
Access Point
Intel 802.11B
Linksys 54G
Bluetooth
HDD
HP Deskjet 450 with Ericsson bluetooth card
Toshiba 40G
Toshiba 60G
Toshiba 80G
HITACHI 60G
ODD
124
MATSHITA UJDA755 DVD/CDRW
Appendix B
Appendix C
Online Support Information
This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
T
Service guides for all models
T
User's manuals
T
Training materials
T
Bios updates
T
Software utilities
T
Spare parts lists
T
TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
T
Detailed information on Acer's International Traveler's Warranty (ITW)
T
Returned material authorization procedures
T
An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C
125
126
Appendix C
Download PDF

advertising