Operating instructions | Acer 4100 Laptop User Manual

TABLE OF CONTENTS
FOR YOUR SAFETY -------------------------------------------------
1
2
SAFETY PRECAUTIONS -----------------------------------SPECIAL NOTES ON LCD MONITORS ------------------
3
BEFORE YOU OPERATE THE MONITOR --------------------
3
FEATURES -------------------------------------------------------
3
PACKING LIST --------------------------------------------------
3
INSTALLATION INSTRUCTIONS --------------------------
4
CONTROLS AND CONNECTORS -------------------------
5
ADJUSTING THE VIEWING ANGLE ----------------------
6
OPERATING INSTRUCTIONS ------------------------------------
7
GENERAL INSTRUCTIONS ---------------------------------
7
HOW TO ADJUST A SETTING -----------------------------
9
ADJUSTING THE PICTURE ---------------------------------
10-11
PLUG AND PLAY -----------------------------------------------
12
TECHNICAL SUPPORT(FAQ) -------------------------------------
13-14
ERROR MESSAGE & POSSIBLE SOLUTION ---------
15
APPENDIX --------------------------------------------------------------
16
SPECIFICATIONS ----------------------------------------------
16-17
FACTORY PRESET TIMING TABLE ----------------------
18
CONNECTOR PIN ASSIGNMENT -------------------------
19
41L1500-786-1A 英文
Before operating the monitor please read this manual thoroughly. This manual
should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1.
The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
2. Shielded interface cables and AC power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modification to this equipment. It is the
responsibility of the user to correct such interference.
As an ENERGY STAR Partner our company has determined that this
product meets the ENERGY STAR guidelines for energy efficiency.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.
Dangerously high voltages are present inside the monitor. Do not open the
cabinet. Refer servicing to qualified personnel only.
41L1500-786-1A 英文
1
PRECAUTIONS
z Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
z Do not place the monitor on an unstable trolley, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a trolley or stand recommended by the manufacturer
or sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
z Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to protect it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
z The monitor should be operated only from the type of power source
indicated on the label. If you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
z The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground
the appliance safely. Do not defeat the safety purpose of the grounded
plug.
z Unplug the unit during a lightning storm or when it will not be used for long
periods of time. This will protect the monitor from damage due to power
surges.
z Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
z Never push any object into the slot on the monitor cabinet. It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
z Do not attempt to service the monitor yourself; opening or removing covers
can expose you to dangerous voltages and other hazards. Please refer all
servicing to qualified service personnel
z To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240V AC, Min. 3.5A.
z The wall socket shall be installed near the equipment and shall be easily
accessible.
z For use only with the attached power adapter (output 12V DC)which have
UL,CSA listed license.
41L1500-786-1A 英文
2
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a
problem.
NOTES
• Due to the nature of the fluorescent light, the screen may flicker during
•
•
•
initial use. Turn off the Power Switch and then turn it on again to make
sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
The LCD screen has effective pixels of 99.99% or more. It may include
blemishes of 0.01% or less such as a missing pixel or a pixel lit all of the
time.
Due to the nature of the LCD screen, an afterimage of the previous screen
may remain after switching the image, when the same image is displayed
for hours. In this case, the screen is recovered slowly by changing the
image or turning off the Power Switch for hours.
BEFORE YOU OPERATE THE MONITOR
FEATURES
• 38.1cm(15”) TFT Color LCD Monitor
• Crisp, Clear Display for Windows
• Recommended Resolutions: 1024 X 768 @60Hz
•
•
•
•
®
EPA ENERGY STAR
Ergonomic Design (TCO’99 Approved)
Dual Input (DVI + Analog) (Only Dual-Input Model)
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
1.
2.
3.
4.
5.
6.
7.
LCD Monitor
Owner's Manual
Power Cord
D-SUB CABLE
DVI CABLE (Only Dual-Input Model)
External Adapter
Audio Cable
41L1500-786-1A 英文
3
POWERCORD
Power Source:
1. Make sure the power cord is the correct type required in your area.
2. This LCD monitor has an External universal power supply that allows
operation in either 100/120V AC or 220/240V AC voltage area (No user
adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s External Adapter
input socket, and then plug the other end of External adapter to LCD
monitor’s DC-power-input. The AC-power cord may be connected to either
a wall power outlet or the power outlet socket on your PC, depending on
the type of power cord supplied with your LCD monitor.
NOTES
A certified power supply cord has to be used with this equipment. The relevant
national installation and/or equipment regulations shall be considered. A
certified power supply cord not lighter than ordinary polyvinyl chloride flexible
cord according to IEC 60227 (designation H05VV-F 3G 0.75mm2 or
2
H05VVH2-F2 3G 0.75mm ) shall be used. Alternatively a flexible cord of
2
synthetic rubber according to IEC 60245 (designation H05RR-F 3G 0.75mm )
may be used.
41L1500-786-1A 英文
4
CONTROLS AND CONNECTORS
CABLE CONNECTIONS
Turn off your computer before performing the procedure below.
1. Connect the power adapter dc cable to the DC-In port on the back of the
monitor.
2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and
connect the other end to the computer’s D-Sub port.
3. (Only Dual-Input Model) Connect one end of the 24-pin DVI cable to the
back of the monitor and connect the other end to the computer’s DVI port.
4. Connect the audio cable between the monitor's audio input and the PC's
audio output (green port).
5. Plug the power cable of your monitor into a nearby outlet. Plug the other
end of the power cord into the power adapter.
6. Turn on your monitor and computer.
Caution: If the AC outlet is not grounded (with three holes), install the proper
grounding adapter (not supplied).
Figure 1
1.
2.
3.
D-SUB Cable
DVI Cable
Audio Cable
41L1500-786-1A 英文
Connecting Cables
4.
5.
5
External Adapter
AC Power Cord
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the
monitor, then to adjust the monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the
monitor’s angle.
• You may adjust the monitor’s angle from -5° to 20°.
Figure 2
NOTES
• Do not touch the LCD screen when you change the angle. It may cause
damage or break the LCD screen.
• Careful attention is required not to catch your fingers or hands when you
change the angle.
41L1500-786-1A 英文
6
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power switch to turn the monitor on or off. The other control knobs
are located at front panel of the monitor (See Figure 3). By changing these
settings, the picture can be adjusted to your personal preferences.
• The power cord should be connected.
• Connect the video cable from the monitor to the video card.
• Press the power switch to turn on the monitor. The power indicator LED
will light up.
Figure 3
External Controls
EXTERNAL CONTROLS
1. >/ Volume
4.
2. </ Volume
5.
3.
/Power Key
41L1500-786-1A 英文
7
/MENU/ENTER
/Auto Adjust Key/Exit
FRONT PANEL CONTROL
•
/Power Key:
Press this knob to switch ON/OFF of monitor’s power.
•
/MENU/ENTER :
Activate OSD menu when OSD is OFF or activate/de-activate adjustment
function when OSD is ON or Exit OSD menu when in Volume Adjust OSD
status.
• </Volume:
Activates the volume control when the OSD is OFF or navigate through
adjustment icons when OSD is ON or adjust a function when function is
activated.
• >/Volume:
Activates the volume control when the OSD is OFF or navigate through
adjustment icons when OSD is ON or adjust a function when function is
activated.
•
/Auto Adjust Key/Exit:
1.
2.
•
When OSD menu is in active status, this button will act as EXIT-KEY
(EXIT OSD menu)
When OSD menu is in off status, press this button over 2 seconds to
activate the Auto Adjustment function.
The Auto Adjustment function is used to set the HPos, VPos, Clock
and Focus.
Power Indicator:
Blue
— Power On mode.
Orange — Power Saving
Light Blue — Power Off mode.
NOTES
• Do not install the monitor in a location near heat sources such as radiators
•
•
•
or air ducts, or in a place subject to direct sunlight, or excessive dust or
mechanical vibration or shock.
Save the original shipping box and packing materials, as they will come in
handy if you ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally
packed at the factory.
To keep the monitor looking new, periodically clean it with a soft cloth.
Stubborn stains may be removed with a cloth lightly dampened with a mild
detergent solution. Never use strong solvents such as thinner, benzene, or
abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
41L1500-786-1A 英文
8
HOW TO ADJUST A SETTING
1.
2.
3.
4.
5.
Press the MENU key to make the OSD window appear.
Press < or > to select the desired function.
Press the MENU key to select the function that you want to adjust.
Press < or > to change the settings of the current function.
To exit and save, select the exit functions,. If you want to adjust any other
function, repeat steps 2-4.
I. Analog-Only Mode
II. Dual-Input Model, Analog Signal Input
41L1500-786-1A 英文
9
III. Dual-Input Model, Digital Signal Input
ADJUSTING THE PICTURE
The description for function control icons
Main
Menu
Icon
Sub Menu
Icon
Sub Menu
Description
Item
Contrast
Brightness
Focus
Clock
H. Position
V. Position
Adjusts the contrast between the
foreground and background of the
screen image.
Adjusts the background brightness of the
screen image.
Adjust picture Focus (available in Analog
mode only).
Adjust picture Clock (available in Analog
mode only).
Adjust the horizontal position of the
picture (availab in Analog mode only).
Adjust the vertical position of the picture
(available in Analog mode only).
N/A
Warm
Set the color temperature to warm white.
N/A
Cool
Set the color temperature to cool white.
User / Red
User / Green Adjusts Red/Green/blue intensity.
User / Blue
41L1500-786-1A 英文
10
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
(Analog
-Only
Model)
(DualInput
Model)
English
繁體中文
Deutsch
Français
Español
Italiano
简体中文
日本語
Multi-Language selection
H. Position
Adjust the horizontal position of the OSD.
V. Position
Adjust the vertical position of the OSD.
OSDTimeout
Adjust the OSD timeout.
N/A
Auto Config
Auto Adjust the H/V Position, Focus and
Clock of picture.
N/A
Analog
Select input signal from analog (D-Sub).
N/A
Digital
Select input signal from digital (DVI).
N/A
Information
Show the resolution, H/V frequency and
input port of current inputs timing.
N/A
Reset
Clears all old status of
configuration
And
re-does
configuration.
N/A
Exit
Save user adjustment and exit OSD
menu.
41L1500-786-1A 英文
11
autoauto-
PLUG AND PLAY
Plug & Play DDC1/2B Feature
This monitor is equipped with VESA DDC1/2B capabilities according to the
VESA DDC STANDARD. This allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, to communicate
additional information about its display capabilities. The communication
channel is divided in two levels, DDC1 and DDC2B.
The DDC1 is a unidirectional data channel from the display to the host that
continuously transmits EDID information. The DDC2B is a bidirectional data
channel based on the I²C protocol. The host can request EDID information
over the DDC2B channel.
THIS MONITOR WILLS NOT WORK IF THERE IS NO VIDEO INPUT
SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY,
THERE MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees (NUTEK). This feature is designed to save electrical energy by
reducing power consumption when there is no video-input signal present.
When there is no video input signal this monitor, following a time-out period,
will automatically switch to an OFF mode. This reduces the monitor's internal
power supply consumption. After the video input signal is restored, full power
is restored and the display is automatically redrawn. This is similar to a
"Screen Saver" feature except the display is completely off. The display is
restored by pressing a key on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD:
The accessory power cord for the Northern American region is the wallet plug
with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for
the power cord shall be 125 volts AC.
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with a
grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration.
The other end terminates with a molded-on type connector body, rated 10A,
250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821
approval power cord in European counties.
41L1500-786-1A 英文
12
TECHNICAL SUPPORT (FAQ)
Problem & Question
Power LED is not on
No Plug & Play
Picture is fuzzy
Picture bounces or a wave
pattern is present in the picture
The power LED is ON (light
blue) but there’s no video or no
picture.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
41L1500-786-1A 英文
Possible Solution
*Check that the Power Switch is in the
ON position
*Power Cord should be connected
*Check that the PC system is Plug &
Play compatible
*Check that the Video Card is Plug &
Play compatible
*Check that the D-15 plug pin of Video
Cable is not bent.
*Adjust the Contrast and Brightness
Controls.
*Move electrical devices that may cause
electrical interference.
*The Computer Power Switch should be
in the ON position.
*The Computer Video Card should be
snugly seated in its slot.
*Make sure the video cable is properly
connected to the computer.
*Inspect the video cable and make sure
none of the pins are bent.
*Make sure the computer is operational
by hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF after hitting the CAPS
LOCK key.
*Inspect the video cable and make sure
that none of the pins are bent.
13
Screen image is not centered or *Adjust pixel frequency (CLOCK) and
sized properly.
Picture has color defects
(white does not look white)
FOCUS or press hot-key (AUTO).
*Adjust RGB color or select color
temperature
Horizontal or vertical disturbances on *Use win 95/98 shut-down mode Adjust
the screen
CLOCK and FOCUS or perform hotkey (AUTO-key).
CLOCK (pixel frequency) controls the number of pixels scanned by one
horizontal sweep. If the frequency is not right, the screen will show vertical
stripes and the picture will not have the right width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase
adjustment the picture has horizontal disturbances on light pictures.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down
mode pattern.
41L1500-786-1A 英文
14
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED:
1.
Check that the signal-cable is properly connected, if the connector is
loose, tighten the connector’s screws.
2.
Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORTS:
Your computer has been set to unsuitable display mode, set the computer to
Display mode given in the following table(See page 18).
41L1500-786-1A 英文
15
APPENDIX
SPECIFICATIONS
LCD Panel
Input
Display Colors
Dot Clock
Max. Resolution
Plug & Play
EPA ENERGY
STAR®
Audio output
Input Connector
Input Video Signal
Maximum Screen
Size
Power Source
Environmental
Considerations
Driving system
Size
Pixel pitch
Viewable angle
Brightness
Contrast Ratio
Response time
(Tr+Tf)
Video
H-Frequency
V-Frequency
ON Mode
OFF Mode
TFT Color LCD
38.1cm(15")
0.297mm( H ) × 0.297mm( V )
120° (H) 110° (V)
250 cd/m2(typ.)
400:1(typ.)
25 (8+17) ms (typ.)
R,G,B Analog Interface
Digital Interface (Only Dual-Input
Model)
30kHz – 60kHz
55-75Hz
16.2 million Colors
80MHz
1024 × 768@75 Hz
VESA DDC1/2BTM
≤30W
≤3W
Rated Power 1.5W rms (Per channel)
D-Sub 15pin
DVI 24 pin (Only Dual-Input Model)
Analog:0.7Vp-p(standard),75 OHM,
Positive
Digital signal (Only Dual-Input Model)
Weight (N. W.)
Dimension
Horizontal : 12.0”(304.1mm)
Vertical : 9.0”(228.1mm)
100~240VAC,47~63Hz
Operating Temp: 0°C to 50°C
Storage Temp.:-20°C to 60°C
Operating Humidity :
10% to 90%
3.7kg
338 (W) × 347 (H) × 154 (D)mm
41L1500-786-1A 英文
16
Switch
External Controls:
Regulatory Compliance
41L1500-786-1A 英文
Functions
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Power Switch
MENU/ ENTER
>/Volume
</Volume
Auto Adjust Key
Contrast
Brightness
Focus
Clock
H.Position
V.Position
(Warm) Color
(Cool)Color
RGB Color temperature
Language
OSD Position .Timeout
Auto Config
(only Analog-input Model)
• Input signal Selection
(only Dual-Input Model)
• Display Information
• Reset
• Exit
UL, CUL, FCC, TÜV/GS, VCCI, CE,
CCC, ISO13406-2, TCO’99, MPR II
17
Preset Display Modes
VIDEO MODE
VGA
VESA SVGA
XGA
IBM
DOS
MAC
XGA
41L1500-786-1A 英文
RESOLUTION
HORIZONTAL
FREQUENCY (kHz)
VERTICAL
FREQUENCY (Hz)
640 × 480
31.469
59.940
640 × 480
37.500
75.000
640 × 480
37.861
72.809
800 × 600
35.156
56.250
800 × 600
37.879
60.317
800 × 600
46.875
75.000
1024 × 768
48.363
60.004
1024 × 768
56.476
70.069
1024 × 768
60.023
75.029
720 × 400
31.469
70.087
1024 × 768
48.780
60.001
1024 × 768
60.241
74.927
18
CONNECTOR PIN ASSIGNMENT
1
5
6
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PIN NO.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
Green
Blue
Monitor Ground
DDC-Return
R-Ground
G-Ground
B-Ground
9.
10.
11.
12.
13.
14.
15.
+5V
Logic Ground
Monitor Ground
DDC-Serial Data
H-Sync
V-Sync
DDC-Serial Clock
(Dual-Input Model)
24 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
PI N NO.
1.
2.
13.
14.
TMDS Data 3+
+5V Power
15.
Ground(for+5V)
4.
5.
6.
TMDS Data 2TMDS Data 2+
TMDS Data 2/4
Shield
TMDS Data 4TMDS Data 4+
DDC Clock
16.
17.
18.
7.
DDC Data
Hot Plug Detect
TMDS Data 0TMDS Data 0+
TMDS Data 0/5
Shield
3.
8.
9.
10.
11.
12.
41L1500-786-1A 英文
19.
Analog Vertical
sync
TMDS Data 1TMDS Data 1+
TMDS Data 1/3
Shield
TMDS Data 3-
19
DESCRIPTION
20.
TMDS Data 5-
21.
22.
TMDS Data 5+
TMDS Clock Shield
23.
TMDS Clock +
24.
TMDS Clock -
Download PDF

advertising